CATHODE RAY TOMES

Frogs

Frogs (Gremlin, 1978) · Manual · 55 pages · 45 sections · original scan

Page 1

721-0001 I I. i°

i

i FT e@part No.

i

I

I r ie]

L OWNERS MANUAL |

Page 2

FROGS

OPERATING INSTRUCTIONS

AND

SERVICE MANUAL

GREMLIN INDUSTRIES, INC.

8401 AERO DRIVE

SAN DIEGO, CA 92123

Page 3

TABLE OF CONTENTS

PAGE

INTRODUCTION 1

IMPORTANT NOTE 2

REPACKAGING INSTRUCTIONS 3

GAME CONCEPT 4

MAINTENANCE 7

DIAGNOSTIC TEST 8

OPTIONS AND ADJUSTMENTS 1

REPLACEMENT PARTS LIST 12

INSTRUCTIONS FOR REMOVAL OF MONITOR 14

SCHEMATICS Fol lowing Pages

Page 4

INTRODUCTION

This is an electronic game that makes extensive use of digital integrated circuitry and television monitor circuitry. This manual assumes the maintenance technician possesses a general knowledge of solid state circuitry,microprocessor, TTL digital integrated circuitry and T.V. monitor concepts. Any individual NOT knowledgeable in these areas SHOULD NOT attempt repair of the electronic portion of this game. IT SHOULD BE NOTED THAT ANY ATTEMPT TO REPAIR THE GAME IN THE FIELD WITH- OUT EXPRESS CONSENT OF THE FACTORY WILL IMMEDIATELY VOID THE WARRANTY: ::

IMPORTANT NOTES:

NEVER replace any components with anything other than exact replacement parts. (See Parts List located on Service Schematics.

NEVER remove circuit boards/connections while power is on.

DO NOT replace the fuse with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause severe damage to internal components if an overload occurs.

ALWAYS consult the manual before attempting repairs.

CORRESPONDENCE regarding this game should be addressed to:

GREMLIN INDUSTRIES, INC.

8401 Aero Drive

San Diego, California 92123

(714) 277-8700

Page 5
IMPORTANT NOTE

An important service note is posted in this game and is repeated here for emphasis:

IF AT ANY TIME THE T. V. SCREEN SHOWS A MEANINGLESS DISPLAY

OR THE GAME OTHERWISE MALFUNCTIONS, SIMPLY DROP A COIN INTO

THE COIN MECHANISM. THIS SHOULD CORRECT THE PROBLEM. IF

NOT, THE GAME REQUIRES SERVICE.

The circuitry in this game has been arranged so that the insertion of a quarter through the coin mechanism will reset the system. This clears up temporary problems caused by power line disturbances, static, etc.

SERVICE TECHNICIAN NOTE:

The system reset circuitry described above requires that the coin counter is attached to the system. If there is a coin counter problem and no replacement is available, the game will function properly if a 10K Ohm resistor is connected across the coin counter input pins to the video logic board.

Page 6

REPACKAGING INSTRUCTIONS

Should it be necessary to ship this game, follow the instructions below for game recrating:

A) If the original shipping bolts have been discarded (Ref.1), obtain four 5/16-18x1 3/4!' hex head bolts with 5/16" flat washers. Carefully lay the game on Its side and attach skid (Ref.2).

B) Place game upright. Tape game keys to upper flange of operator's panel (Ref.3). Crate the game using appropriate shock-absorbent packing material (Ref.4). Include padding on all four corners of the game (Ref.5). After crating is completed, secure package with strapping (Ref.6).

NOTE: If the game is to be shipped to GREMLIN for service or repair, attach a tag identifying the distributor and indicate the service or repair to be made; include the full serial number of the game. GAME MUST BE SHIPPED PREPAID.
Page 7

GAME CONCEPT AND OPERATION

FROGS is a unique single-player video game in which the player controls a frog to catch as many insects as possible in the time allotted. Points are awarded each time the frog catches one of the insects. The setting for FROGS is a colorful scene depicting a marshy area, complete with a pond, lily pads, and tall grasses.

FROG:

The frog appears, at the start of the game, on his lily pad. He hops either to the left or right, or jumps up off his pad. The player controls these motions with a single joystick on the control panel. With the joystick, the player maneuvers the frog either right or left for rapid positioning. In this way, the player can take advantage of all possible shots. The player must be careful to keep the frog from hopping or jumping off the left or right edge of the lily pad. If he is not, the frog splashes into the water. When this happens, the player loses about 4 seconds of time, after which the frog reappears on this lily pad. Also, like a real frog, this one can't turn around in mid-air after it has jumped.

The tongue button makes the frog's tongue shoot out to catch an insect. The tongue can be ejected only after the frog has jumped up for an insect, or when the frog is coming down from a jump. The frog, then, can catch a bug on the way up or on the way down from his jump.

INSECTS:

The words ''CATCH DRAGONFLY FOR FREE GAME'' are displayed on the screen before the game starts. When the game begins, one butterfly appears. At a score of 100, two butterflies show up. Then, at a score of 600, the first fly appears; and at 800, the second fly. As a player's score increases, more insects appear on the screen. This feature makes game play self-adjusting for all player skill levels. During a game, no more than two butterflies, or two flies move across the screen. When a butterfly is caught, the player gains 100 points; 500 points are awarded for a fly.

The butterfly moves at a random height back and forth across the screen. The fly also moves randomly, but it stops for a moment, then darts off around the screen. The dragonfly appears only when 10 seconds are left in the game. A player must have a score of at least 600 for the dragonfly to appear during these last 10 seconds. It will reappear during the final 10 seconds, after it has been caught. When it is caught the first time, the player wins a free game, and is awarded 1000 points. If the player catches it again during these last seconds, he gains another 1000 points. If the free game feature is disconnected, the dragonfly appears; and, if caught, it awards the 1000 points, but not the free game. During game advertising, the message ''GAME OVER' flashes to draw the patron's attention to it.

Page 8

GAME CONCEPT AND OPERATION (Cont'd)

FREE GAME:

When the player catches the dragonfly the first time, the game action freezes briefly and a long 'croak' sound occurs, accompanied by a flashing ''FREE GAME'' message at the bottom of the screen. The game then resumes for the remaining amount of time. When time runs out, the message ''FREE GAME~PUSH TONGUE BUTTON TO START'' appears. At this time, the previous game's score is retained for the player to note. The player simply pushes the tongue button and the free game begins.

The words ''CATCH DRAGONFLY FOR FREE GAME'' appear on the screen only if the free game feature is connected. This will let the operator know at a glance if the feature has been activated, without opening the game cabinet to check. Only one free game is awarded for each paid game, and no additional games are awarded on a free game. The dragonfly does not appear during the free game.

SCORING:

The score is recorded at the top of the screen, along with the ''TIME' and "TOP SCORE" displays. The "TOP SCORE'' is kept on during advertising and adds incentive to attempt to beat it. ''TOP SCORE'' always starts at 500, even after the game has been unplugged and plugged back in.

OPTIONS:

There are four options which may be activated, as necessary:

  • Game time of 60 or 90 seconds; the game is shipped with the 90 second time on.
  • One or two coin option; the game is shipped with the one coin feature.
  • Sound-off switch for advertising sound (frog splash); this sound is on, as the game is shipped. The switch is located on the inside of the coin door, for easy access.

4, Free game activated feature; the game is shipped with the free game on: YOU MUST DISCONNECT IT IF FREE GAMES ARE {LLEGAL IN YOUR AREA! (Refer to Maintenance Section of this manual for instructions.)

Page 9

GAME CONCEPT AND OPERATION (Cont'd)

SOUNDS:

All the sounds in FROGS draw attention and add excitement to the game. A realistic sound accents each move by the frog and flies: the frog's hop, jump and tongue motions, the frog splashing into the water, and the flies darting around the screen. During advertising, the only sound made is the occassional splash of water, when the frog plops off the edge of his lily pad. This sound can be turned off during advertising, if desired, with the switch located inside the coin door.

Page 10

MAINTENANCE

NOTE: IF AT ANY TIME THE T.V. SCREEN SHOWS A MEANINGLESS DISPLAY

OR THE GAME OTHERWISE MALFUNCTIONS, DROP A COIN IN THE

COIN MECHANISM. THIS SHOULD CORRECT THE PROBLEM. IF NOT,

THE GAME REQUIRES SERVICE.

FACTORY ASSISTANCE:

TECHNICAL HELP 1S AVAILABLE FROM THE GREMLIN FACTORY. IF A PROBLEM

OCCURS WHICH CANNOT BE EASILY RESOLVED BY YOUR DISTRIBUTOR, A PHONE

CALL OR LETTER TO THE FACTORY WILL BRING ATTENTION TO YOUR PROBLEM

BY A TRAINED REPRESENTATIVE.

EQUIPMENT:

  • Oscilliscope - 50 MHz or wider band width
  • DVM (Digital Volt Meter)

. OHM Meter

Logic Probe

Solder Station - 75 Watt or less n nu fF Ww

Jumpers

The above list is recommended for anyone attempting to service FROGS.

Page 11

FROGS DIAGNOSTIC TEST

A unique Test IC in FROGS allows the technician to check a number of game elements for proper operation. Among these are: Screen memory test, switch test, switch connection test and

certain IC's. The following instructions show how to run this

important test:

READ THROUGH ALL THE

2.

3. Turn off game power and remove cabinet back. INSTRUCTIONS BEFORE BEGINNING THE TEST!

Refer to FIGURE 1, below, to locate the IC's used in the test. Remove IC's U41 and U48 (Gremlin Part #316-0112 and #316-0119, respectively). Be careful not to bend the pins. Set IC #316-0119 aside. Plug IC #316-0112 into the 316-0119 socket (U48). Be sure to

observe the proper pin configuratéon and to not bend the pins. (A small dot in the upper left corner on the IC indicates pin 1; see FIG. 1).

Turn on game power.

Click the coin switch once to start the test.

If you see the character columns on the screen moving to the LEFT, proceed to STEP 9. This motion indicates that the memory

IC's, U72 through U79, are working properly. If you see NO motion on the screen and, instead, of "zip" sounds, move directly to STEP 10, below.

Video Logic Board (Gremlin #821-0001)

oot indicates pin 1 S| ls so] js

U72 -Y73 U7K U75 U76 U77 U78 U79 ERC

(U72 to U79 Gremlin #315-0036 FIGURE 1 = = = = kn em = 31601 1 316011 3160114 316017 31601 ids

FROGS VIDEO LOGIC BOARD (Top View) hear a number

Page 12

Diagnostic Test, cont'd.

  • SCREEN MOVING: Now, proceed to check the switch assemblies,

as a)

b)

c)

4)

e) follows: Press the 'TONGUE' button and hold it down until the ‘screen

action stops moving. You should then hear, in the follawing order, these sounds:

the hop sound the jump ('boing') the tongue ('zip') the capture ('croak') the fly ('buzz') (no sound)

the splash Follow the same procedure for each of the other switch actions: Hop Left, Hop Right, and Jump. After each, you should hear the same sequence of sounds listed above. Be

sure to HOLD each switch position until the screen action stops and the sounds begin. (The screen should start moving again after the sounds.) If, when you activate one of the switches, the screen DOES

NOT STOP, there is a problem in one or more of the following

areas:

bad switch

bad switch connection to logic board bad input IC, U5 or U6 If the screen action does stop, and, when you activate a

switch, you don't hear ANY of the sounds listed above, then

look for a problem with: a bad connection between the sound and logic boards.

the volume control.(Is it turned up?) the speaker.(Is it connected properly?) a bad switch or switch connection.

lf the screen stops, and, when you activate a switch, you hear only a FEW of the sounds, check these areas: bad sound board

bad connection between the sound board and

logic board

Page 13

Diagnostic Test, cont'd.

10.

11. SCREEN NOT MOVING: If there is no screen response when the

coin switch is clicked, check to make sure the coin switch itself and its connecting wires are good. !f the cain switch is OK, and again there is no screen motion after the coin switch is clicked, there is a problem with one of the IC's, U72 through U79 (Gremlin Part #315-0036). (See FIGURE 1 to locate them; they are numbered 1 through 8 on the drawing). To find out which IC isn't working, simply count the number of "zip" sounds you hear. For example, if you hear 4 "zips", you will know that IC U75 (the fourth IC from the left) needs to be replaced. Clicking the coin switch repeats the "zip" sequence. When you replace a bad IC, let the game run for a few minutes to check the new IC.

When all the tests have been made:

  • Turn off the power.
  • Put IC #316-0112 back into its original socket (U41).
  • Put IC #316-0119 back in its socket (U48).
  • Put the rear panel back in place.
Page 14

OPTIONS AND ADJUSTMENTS

FOR FREE GAME INHIBIT:

Refer to FIGURE 1, below. To disconnect the free game feature, simply insert the pin on the end of one of the two black wires into pin 26 (position #5) of the female connector to the logic board. (These black wires are unconnected and lead out of the female connector at position #1.)

GAME TIME CHANGE: To enable the 60 second game time instead of the 90 second

time, simply insert the pin on one of the black wires, referred to above, into pin 27 (position #4) of the female connector. See FIGURE 1.

MULTIPLE COIN OPTION:

To enable the two coin feature, simply insert the pin on the black wire into pin 28 (position #3) of the connector. See FIGURE 1.

pin # pin connection to logic board

26 (Disconnect Free Game) 27 (60 Second Game) 28 (Two-Coin Per Play)

30 (Ground) To Video Logic Board

FIGURE 1- Pin Connections for Options

Page 15

Gremlin Part Number

200-0002 213-0001 213-0004

220-0019 220-0035

220-0066

220-0071

220-0072

220-0073 240-0006

240-0089

313-0001 313-0004 314-0001 314-0018 314-0019 314-0040 314-0053 314-0058 314-0062 314-0071

315-0031 315-0036 316-0042 316-0043 316-0112 316-0113 316-0114 316-0115 316-0116 316-0117 316-0118 316-0119 REPLACEMENT PARTS - FROGS

(per 10 games)

Description

Monitor, 19" 24-pin 0C Socket 16-pin IC Socket Panel Lock

Lock, Fort Lock

Coin Mechanism, Single Coin Return Button

Coin Return Stop Coin Box

Button, Red Knob,Control Lever

1c LM723 IC LM741EN

1C NE555 Ic 74LS00 IC 74LS04 IC 74L8125 IC 748175 Ic 74Ls08 Ic 74L874 1C 74LS151 1c 280 CPU

Ic 4015 IC PROM 32x8 SEQ 1C PROM 32x8 CTL IC PROM U41

IC PROM U42

IC PROM U43 IC PROM U44

tC PROM U45 1C PROM U46

1C PROM U47 IC PROM U48 Quantity

= 3-4 nne

rn ee

B= ee oe enn onan =

Page 16

Replacement Parts List, cont'd.

Part Number

390-0016 390-0019 390-0020

390-0021

390-0022 481-0009 482-0011 482-0013 482-0015 482-0016

510-0023 510-0037

514-0001 560-0003 815-0020 815-0022

821-0001

821-0002 Description

Lamp, glow Lamp, Fluorescent

Lamp, Black Light Ballast, 15W

Ballast, 20W Diode MDA 3500

Transistor MJ3000

Transistor TIP 110

Transistor TIP 115

Transistor TIP 29

Switch Assembly WICO Switch, Control

Fuse, 2A Transformer #4~10345 Game Power Supply Assembly Fluorescent Light Harness Game Computer Board

Game Sound Board Quantity

Bae oe ene ene we ininn

Page 17

INSTRUCTIONS FOR REMOVAL AND REINSTALLATION OF MONITOR

TOOLS REQUIRED:

WEWwn- Phillips screwdriver Flat head screwdriver Gloves Small piece of masking tape Safety goggles.

NOTE: Refer to game drawing number 721-0001.

INSTRUCTIONS:

l.

2.

12. Unplug game from line.

Uniock and remove rear cabinet door.

Carefully remove ONLY those staples holding the graphics panels (Gremlin part numbers 420-0166, -0169, -0174) to the inside of the game cabinet.

Remove the screws from the two side brackets holding the mirror, and take out these brackets.

Place small piece of masking tape on back side of mirror. When reinstalling, make sure this side faces the same direction.

Next, put on the gloves, and carefully lift up on the mirror and remove it from the remaining brackets. Then, remove the bottom bracket.

CAUTION: MIRROR HAS SHARP EDGES! IT IS ALSO FRAGILE! HANDLE 17 CAREFULLY:

Remove black shadow mask from top of monitor.

Remove four (4) outside bolts from monitor brackets.

Unplug the monitor connector plug.

Make sure the power cable is loose from all wire hold-down clips.

Check to be sure monitor is free from any obstructions and connections, and carefully remove monitor. It is advisable that safety goggles be worn when handling the monitor, as an added safety precaution.

To reinstall the monitor, simply reverse this procedure, starting with this Step and work back to Step 1.

Should you have any difficulties, please contact your Distributor or Gremlin Customer Service.

Page 18

FORM NO. 001-1500

Page 19

PARTS | TITLE 72 /-O00/

QTY PER ASSY

PART NO DESCRIPTION

REF DES

130- 000/ SPEAKER, GAME 6x9?

COVER, SPEAKER 6x9

COVER, TUNETION Bax g i} MONITOR , VIDEO 19" 6 |220-0008 COUNTER, DIGITAL >

MECH COIN SINGLE

TRIM, CONTROL Panter LYVR FRAME, CASH Pook LOCK, FORT Locke led 20 |250-0277 2z |2SO- 0243 23 |\250- 0244 z

Page 20

Gremiin industries, inc. San Diego, California 92123

| QTY PER ASSY | ~ |" | ASSY

DESCRIPTION

7 - RETAINER, GLASS TOP EDGING, U-CHANNEL

/ | | PETHWER, GLASS BOT 2 : RETRINER, GLASS S/DE / A

WINDOW, FROM T= MIRLOR WALI

DECAL, CAUTION WSV

DECAL, VIAPORTANT A/OTE

DECAL, RECYELE

DECAL, S/V SMALL

DECAL, TIP N TELL

Mba, SHADOW GRAPHIC PLAVYEIELD CTR GRAPH Ie PLAYE/ELD LEFT GRAPHK PLAVFIELD BOT GRAMH/C SIDE PANEL GRAPHIC =SUPPORT CLIP, SWITRY CL/PS, STHNO-OFF FORM NO. 001-1501

Page 21

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 22

DESCRIPTION REF DES

SCREW, MACH PAK HD 10-244 1d CAD PLATE

FL. LIGHT ASS¥

BLE LIGHT ASSY

=] | PO | rar | rez | 33 | ea eS faz | 38 | a9 _| 190 | a7 | 92 | q2 |a#o-o/24 [4

Page 23

NOILd1I¥9S3qd A3u ON DMG soodry isi V SOCO-SLEL wu] Siuvd Se |

Page 24

REVSIONS rox [oa] DEScRIrTION onte_[ apenove

—30 eer — D

| ATTACH TO ' a OUT SIDE T OF CARTON ‘ AS in Cc

|'ll

4 ee | ® '

::x31) ATTACH TOSEE SH
Oy REF,6,| Gd are SIDE.1D

\ 1 OF CARTON

#

ATTACH TO _ I)

\‘Y)r 4;| i

OUTSIDE oF 1 ba -te— a |

eneror|| @otie

7&/-2O0/

~=—— A cee sHeETes

NOTES

Page 25

G) gAS 220-0019 STAPLE AeTWwoRk @zas 3 og ° @9) | a3 CRb, TORRE / [ITEMS eer p= eer / @ Ga) 2)

\ | / / ITEM 5/ REF

G SEE SH 9

é @o) 2 Pz a) REF

SECTION AoA [se] Se [eae

i G [YS Pers csr |e a eee oeel SAAR) Zz 1 ASST USED OF APPLICATION (DO_NOT SCALE DRAWING

Page 26

REVISIONS DESCRIPTION

  • (3) PLO WD)e@rree

| ®

(49)(2) Puce Hl ) QAQG ~rer rues (75) @) Pres

FRONT OF CAS EF VIEW B-B (so tan)

view D-D (No SscaLe)

Page 27

|~-zIP CORD

v ea / 1900-/2L BLACK LIGHT ASSY 821-0006 FLOURESENT LIGHT ASSY 815-0016 280 0075 WIRENUTS (LARGE)

  • PLACES

CONTROL PANEL ASSY. 82!-O003 }+— CONTROL PANEL HARNESS 82!-0004 VIDEO MONITOR 200-0002 MONITOR HARNESS 821-0008

RED COIN MECH ASSY. VOLUME. cage 815-0027

as HARNE:

815-0028 ASSY. &2I-O00I al: POWER HARNESS 821-0007 POWER SUPPLY ASSY. 815-0020

SOUND BOARD 821-0002

‘Sam Binge, Guttforwin 93S Greasiin industries, ine. PARTS UIST. PART OR JOENTIFVING NO. [se] S35 JUMPER HARNESS 821-0005 SPEAKER HARNESS 807-0010

SPEAKER 130-0001

FROGS

[SHEET 1G OF [SCALE ca [APPLICATION

Page 28

TITLE

Gremlin Industries, ine: COIN MECHANISM ASSY Son ren cotrernss enn? (7Wo SINGLE MECHANISMS)

B

SHEET 3B IS QO SIZE

FORM NO. 001-1500

Page 29

TITLE

COIN MECHANISM ASSY

(TWO S/NGLE MECHANISMS)

PARTS

LIST

TY PER ASSY

TEM paRT NO 2 DESCRIPTION REF DES

7 | 250-0285 FRAME ,COIN DOOR (MODIFIED 2 |220-0066 MECHANISM, COIN, SINGLE

SCREW, ONE WAY HEAL, 6-32x Te \L6 , CAD FLT WASHER, FLAT AS 1.L.,CAL PE WASHER, £0CK, SPLIT, MIEDIUM SERYES , SS 1.B.,CAD FLT UT, HEX © ~32,CAD F247 AOCK QGAT

~~] 0000/00/00] | ~ PTT TT z f.) AJ a

Page 30
  • THIS ASSY /S INTERCHANGEABLE W/7H &00-

NOTES CON RETURN ByrToW 490-9011 REF.

yo COUNTER (REF)

\ REVISIONS DESCRIPTION

\ SWI7CH BRACK

_ \_ a 7 (REF)

sor Ato -9072 REF. SECTION ACA

MECHANISM ASSY (TWO SINGLE MECHANISMS)

"800-0015. [sneer SOF

Page 31

GREMLIN IND INC

SAN DIEGO CA. 932122

ASSY,POWER

SUPPLY | 815-0020

DWG NO

DRAWN LEE J. LIPTAK

CHECK “eu. i dnt |

REVISION DESCRIPTION

SH | A org | REV

APPR

| DRAFT | CHECK | APPR | RELEASED

SHT 4 18°C’ SIZE

Page 32

SH 2 ASSY, POWFR SUPPLY | BIS- 0020 m2] A | 7 DWG NO OF 3 | rev 2lt- OOOT 2'l- OOIT

CONN. FEM 10 PIN

[SOckET, To-3_ | 4 | STAND- OFFS, CLIPS 1 | CLAMP, CAP. VR4 DIODE, MDA 3500 XISTOR, 2N3055 NUT HEX 46-32 SCREW-MACH RD, HD 44-40 X37 4 [NUT HEX # 4-40 RIVET,POP 3/16 @ [SCR, MACH , HEX, WAS,HD WA-20 X

Page 33

REVISIONS Zone | UTR DESCRIPTION DATE | APPROVED

D

CAPACITOR

souper

OX LO) Os (Os o® a a

“/Awee OM

t U = = a al a pcs Ae omy c GOOG (2 BOGC (7X8)

sug>IN@)iz)/a) N—
4)t=—ht-}=

1 ° i ta aes PINT MOLEX Conn TRANSFORMER

(SKI it WIRING DIAGRAM Blues”, @ BRN 6.5 BAN 6.5' a” BLM (JYMPER) 1.5. BLK RED 6.5~

[oaxk 65° z :

Bis-OOO TA Ate) Q > le \o

(4)(4) (4)SEE DETACHED PARTS L/ST 8/5-0020

[so] SE [ohh ad [

Bem Bear, CoBterne TMA ASSY POWER SUPPLY

Q\ALL POWER TRANSISTORS TO BE MOUNTED WITH HEAT SINKING PASTE £ INSULATING HARDWARE L ALL WIRE TO BE AWG™22G6A NOTES! uncess OTHERWISE SPECIFIED 7 6 5 4

Page 34

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 35

Parts [TITLE ccuemaric

LIST COMPUTER GAME BOARD

Sut b 1S & SIZE

SHeT 1.8.9 1% D SIRE |LTR| DATE REVISION DESCRIPTION Ee 6-6-78| RELEASED 7-1778| ADDED SOUND OUT LUT SHT F FORM NO. 001-1500

82!- 0001

DWG NO

| DRAFT | CHECK | APPR | as | oi

Page 36

Gremiin Industries, Inc. PARTS | TITLE SCHEMATL 821-0001 San Biege, California 91123 COMPUTER GAME BOARD DWG NO QTY PER ASSY PART NO 314-0001 . WES55 DIP 70,7 27 | 314-0018 . 74LS00 U7, 16,27 28 | 314-0019 . UI9, 20, 33,36 29214-0090 | US.6, 17,22 23, 39,40 314 - 0046 U 84 1} | 314-0058 U64-67 32 | 314-0058 314 -00 54 WC, 7415 16 CEC 314 ~ 0061 We 741542 suze 314 - 0062 NC. 7416 74 uIB-5,6F7 314 - 0061 fic. 7auszo fe 37 | 314 ~ 0070 1G. 74LS 86 fus3ssi‘sSSCisdzY 314-001! 4G T4L5151 uUse-63 [sid-0012 _—| nc. 74usi74_SSCS~S~S 314-0073 lic 74e5i75 314-0015 | hC. 7415393 314-0017 [214-0006 | [315-0036 [35-0031 : BOLE

LC. 741508 12, 21,24 25,49. 50-52,56,57 bu} ws WwW | ERESEES8 ly Jw reo es) FORM NO. 001-1501

Page 37
Scan of page 37

This page is a drawing, shown as the original scan.

Page 38

SCHEMATIC

COMPLI TER GAME BOARD

DESCRIPTION

5| 316-OUS [SH-wIS | ™~ 390-0003 q1- O10l La I UW -0974 48! jaei-ooor | 481 -0006 182-0014 WO. F-18501

IC. EPROM Ute FRE

821-0001

DWG NO

SH 4 OF 9 | [RES Ok ORM W/2W 5%

Page 39

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 40

NoTESt Aymeaiare wirn mics As srry vest simcine comeouno tmeess _oreunse anceinca NSoLATED PER. COO® \ae

“Toa [73 az ASS COMPUTER GAME BOARD LOGS

Emew

Page 41

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 42

“Rib 2% 4 u29 ‘SRLD uss) us 746 $393 7acgo4) |

PINS $8, 69,10

By PASS CAPACITORS

PIS 72,7374

NOTES: 34/5

Cre

1 ae Naden

+5¥

C2-cw@e 19-26 CL8-C35 37-644 C51, 652 st

UNLESS OTHERWISE SPECIFIED wen

654321

REVISIONS |

Tone]DEScRITIONoane | arrnoves
4312
(374L 5393AR34

T €

¢ HSL

24,Bot 3 ale

ryt Htboq | R34. 4s

ty

uhQyemvsywe —i
9 og = ETEKawwway Sey Lay ieav7aye 3)
WMLSOF)Us3

744 S86

CAT CA6 CAS CA4 CASussvSYMcvs
1s_|r o e5”

US.

Oey>740.8174CAR CAI caoMIDE
7iae Ce Ce3 oc0
Abe.wal te 124 2,288

ut:

p06Kd 9-15its+

y74 pos — MK 1096-15

2 UIs os MK40 96-15 iL),

GATD pos.mx 4056-15

2 ur poe MK 909-6- 15

——2v78

pot MkIO96-15 a 279

PodRWWRAS casveh 409 Mopveeves
rc139cyY16
[7Rre$$Saek

1 es (Sur) AES Seda. ry i ‘unr q Taltr Low

-s¥

Bysyairy

5V

|TOLERASICES ASE: Sam Senge, Cavornin ORES

eeasome

ms

ims *OTsSCHEMATIC

COMPUTER

GAME BOARD ea or ee av D B2/- 000/ A

D0 NOT SCME DONGfea Monenet gor
64321
Page 43

90 P.cs) psy ysye pe pspepsye pes} 7a]" >> ye Tsy psy [o

(sary

corm DOOR

oureur SH77

NOTE S! uncass oTMERWISE SPECIFIED 7Pels yt

gurevr —4 Burry | Jal SOO +t ral

ME MR sary aS (SHT 7) 74500

tan Binge, Cxtthernin OSE SCHEMATIC COMPUTER GAME BOARD [rar eae en a

Page 44

Gremiin industries, Ine. eee ie eesy FROGS Sound] B2ZI- C002

BOaARB DWG NO SHTS, 5 lo are *D'SizE . [CHECK 7.7. afoajne [APPR | LTR| DATE REVISION DESCRIPTION DRAFT | CHECK | APPR FORM NO. 001-1500

Page 45

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 46

TITLE

ASS Y. FROGS SOUND

DESCRIPTION

Por IM CAR PCNTV

POT 50K CAR PCMTV

EF y > > al Poa a 481-000 BL

CONN MALE 10 PIN

CONN MALE 1Z PIN R ES 27K I/ZW5% Ag ae) el i ;

§

Page 47

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 48

. TITLE

oe ier ASSY FROGS SOUND

CHECK 4, 2.9, d/ea/ne | APPR

DRAFT | CHECK | APPR FORM NO. 001-1500

Page 49

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 50

a REVISIONS DESCRIPTION

Wooo we

L _ _ _IPer. ony

ssh

Buzz? ©

ExT, Nooo INPUT

  • ALL NPN TRANSISTORS ZN4401 2 ALL PNP TKANSISTORS 2N4402- 1 ALL DIODES INTE OR [NAS 4 CAPACITOR VALUES IN) MICEORRRADS 5 RELISMR VALUES IN OHMS € compecton PIN 7 16 KEWINE PID 7 REMI TANS ECARD AIRY CAE CoaRTS

SCHEMATIC

FROGS SCUND BO [COOE TOENT Wo, [BRAS RO. E21- 0002

Page 51

2 1 REVISIONS a | Tore [oR DESCRIFTN wate | APPROVED

D D

FOR REF onuy — (42) POLARIZING. FENCE TYP.

c

B

oT REE pesus 0 J C74 ba «) — N fe Qg 0267 Ss S

N RB? FOR REF ONLY AN)

cone Pan OR NOWENGUATURE 80] BER | went no. Of OESERFHON PARTS LIST iensice aRe Ww ches Gremlin Industries, Inc. FRACTIONS DECIMALS ANGLES San Siege; cxucernin 9308

MyxsDae
MATERIALae2b 78)A S SY

SEE DETACHED P/L hale FROGS SOUND BD.

| TEE CODE TENT NO. DRAWING RO, Ber |. BOARD VIEWED FRON COMPONENT SiDE 121-600) | #ROeS 321-000

NOTES: UNLESS OTHERWISE SPECIFIED["_wexT Assy|__USED ONDB2\-02A
APPLICATION10_NOT SCALE DRAWINGsee 2X|[ser oS OF
65i]4321
Page 52

REVISIONS, DESCRIPTION

3 PLACES

SEG A-A SEC B-B

4 PLACES

8PLACES

3 PLACES

Page 53

P. Gremlin industricssime: | list |ASSY PAMEL, CONTROL

IpRAWN OZ id /LTR| DATE | REVISION DESCRIPTIO N TA cAve| PElEASE PG +See FORM NO. 001-1500

Page 54

TITLE

[ cremun Industries, inc. ier | ASSY. PANEL , CONTROL San Dregs, Catifernia 92913

aa ASSY ie PART NO ott ae NSIS NSIS

PIN, COTTER .O78 0.D.X/"L6 BOLT, CARRIACE "8-32 X 1 %2" NUT HEX 8-32 ea 29] ea [3.4] Ex [38] EE [40 | [4 | a2 | 43 | ca 48 |

Page 55

|252-0054 | P 1280-0070 | 1 j2so-o/03 {1 p

wy SST ERR ISISIST EET FT =s Gag

SWITCH, ASSY_WICO

SWITCH CONTROL

Pt | joey St