Baseball TM-135 1st Printing
Baseball (Ramtek) (Ramtek, 1974) · Technical Manual · 80 pages · 57 sections · original scan

This page is a drawing, shown as the original scan.
GAME NO: 001 @
GAME SERIAL NUMBER LOCATION
Your game’s serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the label located on the rear of the game cabinet. Please mention this number whenever calling your distributor for service.
BASEBALL
» 7 —F (es) ID) v
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Catalog
ATARI INC. 1265 BORREGAS AVENUE -O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 ¢ TELEX 35-7488
AWarer Communcations Company
Copyright © 1979 by Atari, Inc. All rights reserved
No part of this publication may be reproduced by mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permission requests, write:
ATARI INC 1265 Borregas Avenue P.O. Box 427 Sunnyvale, California 94086
5H
Lithographed in the U.S.A
i Baseball™
table of
contents
1 location setup A. INTRODUCTION ... 00.2.0 0 0000 n eens 1 B. GAME INSPECTION... 2 C. VOLTAGE SELECTION . 2
- Low-Voltage Problems . wee 1-2
- High-Voltage Problems............... vee 12 INTERLOCK AND POWER ON/OFF SWITCHES . SELF-TEST PROCEDURE ................. VOLUME ADJUSTMENT . : reo OPERATOR OPTIONS ... 00.01 c cect nee nee ommys
2 game play A. ATTRACT MODE .... 2.0.2... 0c ccc tte teens B. READY-TO-PLAY MODE . C. PLAY MODE..............
3 maintenance and adjustments CLEANING . . 32 7 FUSE REPLACEME: . 3-2 C. CONTROL PANEL ACCESS . - 3-3
- LED Switch Replacement .... 3-3
- Play Select PCB Repairs ....... -
- Trak Ball™ Maintenance and Repair . 3-4
- TV Monitor Removal.......... .. 3-4 D. GAME PCBREMOVAL .... 2.0.6.0. c cece ect e ete eens 3-4
Baseball™ | iii
table of
contents
4 details of electronic operation
Roo Tommy POWER SUPPLY ... 0.00.00 ccc cette teens SYNC GENERATOR MICROCOMPUTER CIRCUITRY
- MPU, ROM, andRAM .....
- Address Decoding Circuitry
- OClock Driver........ : 4, Watchdog RESET...........- ALPHANUMERILCS GENERATOR . . DISPLAY RAM. GRAPHICS GENERATOR MOTION OBJECT RAM VIDEO SUMMING CIRCUITRY SWITCH AND TRAK BALL INPUT CIRCUITRY . DISPLAY PCB AND COIN COUNTER OUTPUTS. . . ee AUDIO CIRCUITRY «1.006 nee ee
5 illustrated parts catalog
list of
illustrations
Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Voltage Selection Plugs... 1... ccc eee tenes 1-2 Location of Interlock and Power On/Off Switches ..........000000- 1-3 Location of Self-Test Switch and Volume Control. Option Switch Settings.............0..00 Fuse Replacement... . Control Panel Access . . : L.E.D. Switch Replacement. . . 3-3 Play Select PCB Removal ... 34 Trak Ball™ Control Repair - TV Monitor Removal
iv Baseball™
Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-9 Figure 4-10 Figure 4-11 Figure 4-12 Figure 4-13 Figure 4-14 Figure 4-15 Figure 4-16 Figure 4-17 Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7 Figure 5-8 Figure 5-9
Table 1-1 Table 1-2 Table 4-1 list of
illustrations
Game Block Diagram... 00... ccc ccc etn eee e nee Game PCB Biock Diagram Game Power Distribution and Wiring Diagram . Game PCB Power Distribution .. . . Syne Circuitry ... . Microprocessor Circuitry . . Program Memory ... MPU RAM Address Decoding Circuit Alphanumerics Generator Display RAM....... Graphics Generator . . Motion Object RAM Circuitry Video Summing Circuitry Switch and Trak Ball Inputs Display PCB and Coin Counter Outputs Audio Circuitry .. . Final Assembly .. . Coin Door Assembly . Front Bezel Assembly : Type B Power Supply Assembly. . Control Panel Assembly . . . Trak Ball™ Assembly . . Play Select PCB Assembly . . Baseball PCB Assembly .. . . Harness/Switch Assembly . .
Self-Test Procedure Option Switch Settings . Memory Map list of
tables
Baseball™ v
WEST and CENTRAL U.S.A. Parts for all Atari Customers. Sales and Service. Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103 (Monday - Friday, 7:30 - 4:00 pm Pacific Time)
From California, Alaska or Hawaii, dial (408) 745-2900
From anywhere else in this area, dial toll-free (800) 538-1611
EAST U.S.A.
Atari Inc. New Jersey Customer Service Office 44 Colonial Drive, Piscataway, NJ 08854 Telex 37-9347 (Monday - Friday, 8:30 - 5:00 pm Eastern time)
From New Jersey dial (201) 981-0490
From anywhere else in this area, dial toll-free (800) 631-5374
vi Baseball™
a. introduction
Baseball™ is a new one- or two-player video game designed by Atari. The game rules, catching, pitching and batting are realistically displayed on the screen, accompanied by sounds of crowd cheers, noise, the crack of the bat, and a ball sound.
Player controls are mounted at either end of the game. The player controls consist of two multi-function LED pushbutton switches and Trak Ball™ controls. (The switches’ functions are described in the graphics on the control panel.) The Trak Ball rolls smoothly with a shove from the palm of your hand: this moves either the batter or outfielders on the screen.
Baseball™
b. game inspection
Your new Baseball game is manufactured ready to play immediately after removal from the shipping carton. Your cooperation is desired in order to supply the final touch of quality control to your game. Therefore, please follow the procedures below to ensure that your game is in good condition:
- Examine all external parts of the game cabinet for dents, chips, or broken parts.
- After determining that the game has been received in good condition, unlock and open the access panel.
Carefully inspect the interior and verify the following:
All plug-in connectors are firmly seated. ¢ All integrated circuit packages (chips, ICs) in sockets on the game printed circuit board are firmly seated. ¢ No hamess wires are disconnected. ¢ No loose foreign objects are present, especially metal objects that could cause electrical problems.
Be sure that all major assemblies are checked. Check the game printed circuit board (PCB), the speakers, player controls and the TV monitor for secure mounting.
c. voltage selection
Use one of the following four plugs to set the proper voltage for your game. If you have any problems with your game as described in either paragraph below, then change the voltage plug as required.
Line Sees] Range ee ee | Selection Plug Color | _86-104vac | 104 VAC 100-125 VAC a (installed at factory) 190-220 VAC Green zo-240vac_ | Red
- Low-Voltage Problems If your game is set for 110 VAC (or 220 VAC) and your line voltage is usually below 110 VAC (or 200 VAC), you may experience a decrease in the size of the monitor picture and/or the game operation will be erratic (weird things will appear on the screen).
- High-Voltage Problems If your game is set for 95 VAC (or 210 VAC) and your line voltage is usually above 110 VAC (or 220 VAC), the monitor picture size may increase, the game will run hotter, and the game will be prone to an increased rate of failures.
VOLTAGE. SELECTION
POWER-SUPPLY PLUG
CHASSIS
. ON/OFF AND [Ese] nrerocx
- Mirek
Figure 1-1 Voltage Selection Plugs
1-2 Baseball™
d. interlock and power on/off switches
To minimize the hazard of electrical shock while you are working on the inside of the game cabinet, two interlock switches have been installed (see Figure 1-2). One is located behind the access panel and one behind the coin door. Any of these switches will disconnect all the AC line voltage from the game circuitry. Check for proper operation of the interlock switches by performing the following steps:
- Unlock and open the access panel and the coin door.
- Plug the AC line power cord into your local AC outlet.
- Set the power on/off switch to the on positon. Close the access panel and coin door. Within approximately 30 seconds after closing the last door, the TV monitor should display a picture. (The game lighting should light immediately.) Slowly open either door. The TV picture should disappear and the game lighting go off when either the access panel or coin door is opened approximately 21/2 cm (one inch). If the results of step 5 are satisfactory, the interlock switches are operating properly. if the picture and lights stay on, check to see if either interlock switch is broken from its mounting or stuck in the on position. Close and lock the access panel.
INTERLOCK SWITCHES
POWER ON/OFF SWITCH
Figure 1-2 Location of Interlock and Power On/Off Switches
Baseball™ 1-3
e. self-test procedure
This game will test itself and provide data on the TV monitor and speakers to demonstrate that its circuitry and controls are working properly. No additional equipment is required. See Figure 1-3 for location of the self-test switch. To start the procedure, slide this switch to on as indicated in the figure.
See Table 1-1 for further details and instructions on the self-test. We suggest that you perform the self-test each time the coin box is emptied.
f. volume adjustment
If the volume is incorrect for your location, open the coin door and adjust the volume control as indicated in Figure 1-3.
VOLUME CONTROL. TO DECREASE TURN COUNTERCLOCKWISE
SELF-TEST SWITCH
Figure 1-3 Location of Self-Test Switch and Volume Control
1-4 Baseball™
Table 1-1 Self-Test Procedure
Open the coin door. Locate the self-test switch inside the cabinet on a metal bracket. It’s to the right and slightly below the door opening. Slide the switch to on.
Result if Test Passes Result if Test Fails
Preliminary Test Crowd noise is turned on. No crowd noise: Indicates a defective speaker, volume control set too low, or faulty crowd noise circuitry.
- RAM/ROM Test TV monitor displays RAM OK ROM OK Monitor displays the message BAD RAM if the random-access memory is at fault.
Monitor displays the message BAD ROM if a read-only memory is at fault.
- Trak Ball™ Test Two white figures will appear on the monitor, one for each Trak Ball control. They will move exactly as the control is moved— up/down, right/left, and diagonally at both angles. Roll the Trak Ball in all directions.
- Switch/Crowd Cheer Audio Test Move the Trak Ball and then press each of these switches:
- play/select switches
- coin door switches © slam switch For each pressed switch another white figure will be frozen onto the screen wherever the rolling Trak Ball last placed the moving white figure. Switch pressure will also cause a crowd cheer to be heard simultaneously from both speakers. One or both white figures are not displayed, or one or more directions of movement will not respond, such as up/down. Suspect a bad steering PCB on the Trak Ball or bad steering circuitry on the game PCB. No crowd cheer and no white figure frozen on screen indicates bad switch.
White figure frozen on screen but no crowd cheer indicates bad crowd cheer audio circuitry.
Return the Self-Test Switch to its off position; then close the coin door.
Baseball™ 1-5
g. operator options
The operator options offer maximurn player appeal for your game’s location. These options are listed in Table 1-2. They are preset for a certain game set-up during production.
To change the toggle positions of the switch assembly and set the desired options, you do not have to remove the game PCB. Unplug the game, and open the access panel. Then locaie the four-toggle switch assembly on the PCB near the edge connector (see Figure 1-4).
Set the toagles for the desired options as listed in Table 1-2. Close and lock the access panel. Plug the game in and verify attract mode.
Table 1-2 Option Switch Settings Switch Settings on 4-Toggle DIP Switch (located at position K10\on the game PCB) 2 3
Most difficult setting: Infielders are excelleni players and innings are shortest. > Intermediate settings Easiest seiting: Infielders are poor players and innings are longest.
Atari recommends, at least for initial location setup, using one of the two middle settings. Regardless of the setting, the infielders always get better as the inning progresses to provide challenge for the players.
GAME PCB
OPTION SWITCHES
Figure 1-4 Option-Setting Switches
1-6 Baseball™
game play
The Baseball™ game has four basic modes of operation: attract, ready-to-play, play and the self-test. The attract mode starts after the play mode or after power-up. It ends when a coin has been inserted into either coin slot. The ready-to-play mode begins after a coin has been inserted. It ends with the pressing of either LED switch.
The play mode starts whenever a player presses an LED switch. The game does not automatically start after a certain time has elapsed. The self-test is a special mode used for verifying proper game operation. It begins with the self-test switch set to on, and ends when the switch is set to off.
Baseball™
a. attract mode
The attract mode is specifically programmed to attract potential players by displaying the basic sequence of game play. The fielders run out to their respective places on the playfield, pitches are made, batters run around all the bases, and three outs finally cause the diamond to invert by 180°. The game repeats this sequence, so that the opposing side of the cabinet is now “playing”.
Scores for balls, strikes, and ouis are totalled and displayed as the attract-mode sequence progresses. In addition, the INSERT COINS and appropriate coinage phrases are displayed at the ends of the screen. No sound is generated during this mode.
b. ready-to-play mode
This mode starts when either coin switch is activated by a coin. Crowd noise begins at this point. Both sides of the TV monitor flash the message PUSH START until a player pushes either LED switch.
c. play mode
Fielders run from the dugout to their proper places. The game will prompt the players to select one of the four types of hits or pitches by flashing SELECT PITCH or SELECT HIT on the ends of the screen. A player chooses a hit or pitch by pressing his or her play select switch until the indicator LED corresponding to the hit or pitch selected is lit. If the player does not do so, the game will automatically choose the hit or pitch randomly.
As a player successfully hits the ball, control of the runner is gained by rolling the Trak Ball™ in the proper diagonal direction toward first base, and so on around the diamond. The crowd noise increases with a triple, home run, score or out,
Scoring is exactly as in actual games, i.e., three strikes equals an out, four balls equals a walk, and three outs mean that side retires. Coinage of the Baseball game for the first inning is one coin per player. The second and subsequent innings each cost one coin, regardless of the number of players.
2-2 Baseball™
maintenance
and adjustments / {<
Due to its solid-state circuitry, this Atari unit should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in this manual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detail to be understood by a person with moderate technical background.
Baseball™
The exterior of the game cabinei and the glass and acrylic panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the small acrylic play select panel, because any dust can scratch the surface and result in fogging the plastic. (The large monitor shield is made of tempered glass and should be scratch-resistant.)
POWER-SUPPLY CHASSIS
WF 3AG 3 Amp. 250V. Slow-blow
b. fuse replacement
Baseball contains six fuses, five on the power supply assembly, and one on the floor of the cabinet (not including TV monitor). Replace fuses only with the same type as shown in Figure 3-1. See the manual on the TV monitor for additional monitor fuse data.
SAG 3AG 2.5 Amp. 125V. 8 Amp. 125V. Fast-blow
3AG 2.5 Amp. 250V. Slow-blow
(on floor of game cabinet)
Figure 3-1 Fuse Replacement
3-2 Baseball™
c. control panel access
Prior to replacing any removable component from the control panel or prior to removing the TV monitor, unplug the game and follow the steps outlined in Figure 3-2.
- Unfasten and remove three allen-head ‘Screws from control panel.
- Carefully swing the control panel open.
Figure 3-2 Control Panel Access
- LED Switch Replacement The light-emitting diode (LED) switch on top of the control panel has a very low failure rate. In case the switch should ever be suspect, first test it. To test or replace the switch, refer to Figure 3-3,
- Play Select PCB Repairs Two problems could occur with this PCB. A light-emitting diode could burn out, or one of the six incandescent lamps could burn out. To replace any LED or lamp, open the control panel and remove this small PCB as described in Figure 3-4.
L.E.D SWITCH:
TO REMOVE TURN COUNTERCLOCKWISE NORMALLY. CLOSED (N.C.) CONTACT
LIGHT-EMITTING DIODE (L.E.D.) CONTACTS
CONTROL PANEL
NORMALLY OPEN (N.O,) CONTACT COMMON CONTACT
- Remove all wires from the faulty switch. ° Turn the switch counterclockwise while holding the cone-shaped nut on the outside of the control panel.
- Install a new switch using the reverse procedure.
- Reconnect the harness wires.
DOUBLE-POLE SINGLE-THROW (DPST) SWITCH WITH INTERNAL LED
Figure 3-3 L.E.D. Switch Replacement
Baseball™ 3-3
- Open contro! panel as illustrated in Figure 3-2.
- Remove the two washers and nuts. . Unplug the white connector. . Remove the play select PCB. . Replace lamp or light-emitting diode, as needed. The lamps are NEMA type no. 47 (Atari part no. 70-11-47). PPoOR
Figure 3-4 Play Select PCB Removal
- Trak Ball™ Maintenance and Repair To maintain this control, you will only have to lubricate the bearings approximately every 4,000 innings or $1,000 in income earned. The number of innings can be read off the coin counter, located on the coin door, Use only two drops of 3-in-One® oil in each of the ball bearings. (Each Trak Ball control has five bearings.)
For further instructions on how to replace the trak ball or either steering PCB, see Figure 3-5.
- TV Monitor Removal If you should need to service or replace the 23-inch TV monitor, you must first remove it from the game cabinet Follow the instructions in Figure 3-6.
3-4 Baseball™
d. game pcb removal
You may wish to remove the game PCB for service or inspection. To do this, proceed as follows:
© Open the access panel.
- Locate the two screws that secure the game PCB in its slots, and remove them.
- Unplug the edge connecter; then carefully slide the PCB straight out of its slots. Be careful not to twist the board, as this may loosen connections or components.
- Repiace or repair as required. © Reinstall the PCB, making sure that the edge connector is properly plugged in. Note it is keyed to fit on only one way, so if it doesn’t slip on easily, don’t force it! A reversed edge connector may damage the game! ° Replace the securing screws through the holes in the PCB.
- Close and lock the access panel.
- Check that the operation of the game is correct by performing the self-test.
Trak Ball™ Control Removal
- Open contro! panel as illustrated in Figure 3-2. See © in figure.
- Remove three carriage bolts from assembly. See @.
- Remove the Trak Ball assembly. See ©.
Trak Ball Replacement
- Remove three countersunk machine screws from the Trak Ball assembly’s acrylic top plate. (When the assembly is installed, these three screws are right underneath the control panel.) See @.
- Remove and replace the ball. See ©.
Steering PCB
- Unplug connector on steering PCB. Remove two crossrecessed machine screws, associated washers and hex nuts from the steering PCB. See ©.
- Remove the steering PCB. See @.
- When replacing this PCB assembly, be certain that the black toothed wheel turns freely between the two halves of the red photo sensor device.
Figure 3-5 Trak Ball™ Control Repair
Baseball™ 3-5
3-6 Baseball™
High voltages exist in any television unit, even with power disconnected. Use extreme caution and do not touch electrical parts or the TV chassis with your hands or with meta! objects in your hands!
Open control panel above and to the right of the coin door as shown in Figure 3-2. Open the coin door. Carefully loosen tape at exposed end of cardboard bezel. Do not remove the bezel. Open access panel. Unplug control panel connector for opened player control panel. Remove the four TV monitor carriage bolts and associated hardware. Unplug TV monitor chassis connector. Stide out TV monitor shelf assembly along with the bezel; the opened control panel is altached to the assembly.
Figure 3-6 TV Monitor Removal 2PLCS
details of electronic operation
@0n 4 oe . 5
This chapter provides a general overview of the operation of the circuitry contained on the game printed circuit board (PCB). This information has been organized with an emphasis placed on troubleshooting the game PCB circuit by circuit.
The Baseball game block diagram of Figure 4-1 illustrates the major components, including all controls remote to the game PCB. The function and direction of the information to and from these various controls is also shown.
The game PCB block diagram in Figure 4-2 illustrates the division and function of the various circuits located on the game PCB and how they are controlled by the microprocessor. Refer to Figure 4-2 as you go through the following circuit descriptions.
Baseball™
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Tv MONITOR
acrowen wremioes woniton | contro nutty
soy WNREG ULATED) ‘VERTICAL DEFLECTION
INTERLOCK
GAME SELECT LED DISPLAY
ame LaYERONE NED eee | cine somno weer conrnot paves
PuaveRTwo ! Track sPeaKen baat ContRoL GAME SELECT LED DISPLAY SELF-TEST
BRACKET LOCATED BEHIND THE COIN a |
MECHANISM
Figure 4-1 Game Block Diagram
Baseball™ 4-3
- ———— —— — —— —_ ——— —-4 | MICROPROCESSOR CIRCUITRY |
‘ADDRESS DECODING cerRcUITAY
RAMDO-RAMD7
ADDRESS: BUFFERS
BEDIRECTIONAL DATA BUFFER v0.07
poor bata BUSo-DBUS7 BUFFERS.
SWITCA AND TRACK BALL INPUTS.
Figure 4-2 Game PCB Block Diagram
4-4 Basebalil™
syne ALPHANUMERICS GENERATOR
RAMDO-RANO7
pispi6.Disp23, MOTION ‘OBJECT RAM
DISPLAY RAM GRAPHICS VIDEO out GENERATOR Dispe-pisp1s
PLAYFIELD Gate
oBuso-obus7
auoio Cimcvreny ) v0 Deuso.DBUs7
‘ANODE OUTPUTS:
DisPLAY PB AND COIN COUNTER outPurs TOLEDS,
‘CATHODE OUTPUTS
cONENTA —} peuso.DBuST
Baseball™ 4-5
a. power supply
(See Figure 4-3)
The power supply {located on the bottom) produces all the necessary game power as shown in Figure 4-3.
The game PCB receives an unregulated + 10 volts DC at pins B and 2 of the PCB edge connector. The +10 volts DC is rectified in the power supply assembly and regulated toa stable +5 volts DC by the LM323 on the game PCB. The regulated +5 volts DC is distributed throughout the PCB to power all logic circuits (see Figure 4-4).
The 25 volts AC is received by the game PCB on pins W, 19, X, and 20 and rectified by diodes CR1 and CR2, then filtered by capacitor C62. Zener diode CR3 regulates the +18 volts DC to +12 volts DC. This voltage powers the LM324 IC in the audio circuitry.
The unregulated +18 volts DC is used to supply the TDA2002 audio amplifier in the audio circuitry.
ane] Tegsatetattou! POWER, PCB
© | 15 Pos moLex Plue + MALE TERM RNALS a
Tk Power wey [at
Supply 5
sey Re aw)
=H ac. E INPUT | ie ¢ ;
stam sure
Coin Door rey NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL’ Reproduction fo:bidder, without the speci
Ten liverge, no right te reproduce this drawing 's granted or the subsecl malter thereat urless by written agreement with or writen permission trom ine corporation.
Figure 4-3 Game Power Distribution and Wiring Diagram
4-6 Baseball™
TT power SuReLY ASSY ey Je} i BK E aa ee SEE bunt ree ven
Teter} tonceer meat eu mines 1 te
rox cain coor
-C_JO nce nad ceCres cone
EBUFROL “PANEL PURER 1 * <
ASSY/ SeneMariC. poses 4 PLAY SELECT Pe} on fourescor SP pee “ee ree
NOTIGE TO ALL PERSONS RECt
CONFIDENTIAL: Reproduction. TO CONTROL PANEL PLAYER & Figure 4-3 (Continued) Game Power Distribution and Wiring Diagram
(034562-01 B)
Baseball™ 4-7
b. sync generator (See Figure 4-5)
The basic frequency of the sync generator is a 12.096-MHz clock, generated by a crysial-controlled oscillator consisting of crystal Y1, inverter N4 and several discrete components. The output of the oscillator is 12 MHz. Examination of this signal with an oscilloscope (at pin 2 of N4) should show a period (or one cycle) of approximately 83 nanoseconds (.083 microseconds)
This base frequency is then divided down by binary counters P5, P6 and N6. These provide the various horizontal synchronization frequencies (1H thru 256H). The final output of this horizontal counter chain is 256H (at pin 13 of N6). This signal is, in effect, a division of the base frequency by 768, or 15,750 Hz. The period of 256H is about 63.5 mictoseconds. The 256H signal, as well as other horizontal signals, are used to generate the HBLANK and HSYNC timing pulses at flip-flop N5. See Figure 4-9 for the The HSYNC signal is used to clock two stages of vertical sync counters M5 and M6. The HSYNC signal is divided down by these counters to form the various vertical synchronization frequencies (1V thru 128V). These two stages are used, in effect, to do a divide by 262 of the HSYNC signal. This results in the final output of these counters (128V at pin 11 of M6) to be at a frequency of 60Hz {the period is approximately 16.6 milliseconds). The various vertical frequencies address a sync PROM (L5) whose data is latched at the output of L6. The outputs of this latch are the various polarities and phases of the vertical timing frequencies used to synchronize the TV monitor display. See Figure 4-9 for the relative timing of these waveforms.
The end result of the horizontal and vertical timing waveforms is to synchronize the TV monitor display. This display consists of 262 horizontal lines per frame, with each line being the equivalent of 768 (12 MHz) clock pulses. Each frame is repeated 60 times per second, providing ihe necessary frequency of display refresh to provide a stable, relative timing of these waveforms. non-fiickering display.
Pp Rs? re | aid tov Bn vow A2,9)12,13, 1 18 /36,79 x)+sv | cue) siovconres) [eB] 2 |— st +5V Cir 14 -18, 20-22, 24-26, 297-31, 30,37,42,46, 22 i Jeo TL cavenss)
te.SVAC CT [Al T
asvac [w ‘rey Pid i im | 3S) zsvac [x 7 peeze | ag (BYPASS)
T22ee
2svac cr GND Te GNO (ROWS 5,8) NOUICE 19 ALL nERSONS RECEIVING THIS ORAWING TIAL: Repraduction. torbidden without the
Grawing or any design oF technies! information shown thorean, nor an ighto reproduce this drewing b any bat thereo), except for manulacture by vendors of porated and for marulacture under the corpor fen license, no right to reproduce this drawing 1s gra Sino Subject malar thoregtaniess by water agrownent Wwith or wetter permission from the corporation.
Figure 4-4 Game PCB Power Distribution (Part of 034634-XX_ B)
4-8 Baseball™
| RRO | 2 IZ. | PAIZ |
rary 2 Fi — Q e - 6 =
| an | lt |s |b de | bla Is ede | Isle Is lode | ||||||||
| a7 | RS | PO | PZ PIPE | POP) PZ PS PE | Po PI PZ P32 PE | ||||||
| 330 | 330 | Teco | cer | cer | Na | ||||||
| 2 | Ps | Poe | Ss | i) | No | NS | cy | ||||
| Na | 7 | Na | Ma | eT | gee | Te | ket | ane | 7 | leer gai | Tere. |
| Soe | it | 4 | es | [>o2 | 2hep BIN CNTR | 2 cp BIN CNTR | Zep BIN CNTR | of | |||
| 04 | 2 690 | O48 | O4 | fag a) ar a3 wR | ‘nd a1az a3 ma | ‘og ot a2 a3 Ma | |||||
| Bae | a | [3 ie | ‘a | is [3 fe fv a | ia 3 a wy |
0 ek
| Tree | RS | | | eRe | eRIZ, |
a)
| " | ZEEE | a2 | |
| BLaG | eong | es | |
| Na, | $ | 28 | |
| TSOH | 13 | : | zSeH |
P7
| au—' | So? | 4h |
O48 oan Py 24 —2[>02— 7— 320 —3y of PT sev 302 329
¥ $
| 2 | vatanx—'S[a0 | Jo | ap | 20; | —vetank |
izev —Hao cs 20}¢—VBUANK
| wav —2as, Zog|0 | 4], | rahe |
| 3zu —Alae 82 | Le. | —YRESET |
av —4as9e 45175 gal'> — ennscrcen
| Je og! | 3 | rn |
4v Un oz ays
| el, | OF | FF | 10 |
| w——Sar hz | ely | 38 | USN |
ww —Slas sat! eae xe)
| \4 | > tT | 1 |
Arie fia fia fiz he jit pS pz ae ‘256 pao RID
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL” Reproduction foroigden. without the Specie written permission of Stary ne.” Sunnyvale, zeae Giiiornia Tne orbwing is only conttionali sued. ard
| zr | 7232 | B23 | neither racaipl nor possession (neren! confers or transfers |
| 5 | 2898 | 2aga | Sry right hor leense fo use, the subject matter ofthe |
| ln | Grawing or aay design of | techincal itfornation stown | |
| iw | thereon. norany ‘ght fo reprocuse | this drawing orany part |
‘hereof, except for manufacture by vendors ol Atav, incor porated and for manufacture ten iicense, no right to reprox fr the subject matter thereo! ‘under the corporation's writ duce tvs drawing granted ‘uniess by written agreement ‘with or witten permission trom the corporation,
Figure 4-5 Sync Circuitry (Part of 034634-XX B)
c. microcomputer circuitry
The heart of the game PCB is the microcomputer circuitry. A brief description of the major components and their functions is provided in the following paragraphs. Note 3. that the microcomputer components include the following:
- MPU at location C2, address buffers at B1 and C1, and data buffers at location E2 (see Figure 4-6). -02 version, or PROM memory
the -01 version (see Figure 4-7). RAM memory at locations N2 4-8).
gates (see Figure 4-9). Address decoding circuitry B3, ROM memory at locations M1, NO, N1 and P1 for the at BO, CO, DO, D1, EO, E1, FO, Fl, HO, H1, JO, J1, KO, K1 and MO for
and M2 (see Figure
C7 and associated
Baseball™ 4-9
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING GONFIGENTIAL” Ropreduction ‘orbigden. winout. the
| 5 | @ | reac watten, guimreion of tar ne." Sunnyvale, |
Siomnia Tn arae'ng 8 oniy sonat‘onay saved an
| aes |* | Asusis | neitter recorpt nor possession (Nerec! confers ar vaners |
=O) Sy oeh ne see trae he lea mai the 4 fawing or any design or technical Information shown asia [4 4 2 nausig Ieaon ray git produce fe cawing or any pa a inereot, except tov manlacture by weondors of Nar Ineo Ds Soratod andor manstacture under te corperation's wt
| Apia | asusis | foricenso. ce fpnt to veprodsce tis geawing Is granted |
PRD Srins subject waiter theroor uniess by wniterseareement
| f | Pa | Sino witen permis Tom the eoraeration |
ap Pe agusi2 29} 0
2} Rey 8h2 . _a war
| -@ | patella, | 6Y | ABUSII | |
| +59 | avol'2 | | : | 10] 35 | 5 |
| . | 7 | ue 31 | ABUsio | |
| ABa, | = | 28 LSIST | ||
| RIS | cl | ABLSD | ||
| i | n | f® | 4 be | |
| c2 | sania | Agus8 |
ok «
| ReseT | 90-@010 | rc | |
| eg | © | arwereczys | ae |
vee
| DOE. | i | ae7 fle | yp | ICI | PS | = | ABUST | ———-_ | |
| eit | . | 3p. | LS9244 | ||||||
| ~ | is | ft | A | 2 | 7 | ||||
| 53 | ye | avs |'S | 2 | P| | te | pause | 324 | 5 | agus? |
| 4 | p© | uw | 2 | ||||||
| zfalel> | *5¥ | jo) | — | 2 | TT} | asuse | |||
| Wer Ree RI RE | 2 | e | ia | ray | > | ABUs. | |||
| rey—ega | ag | IE | “e | -(s) | ? | moot | é | “+ We | |
| as | u_f | i | 9 | bay | > | Agus | |||
| L | iy | Av? | z | — ABUSZ | |||||
| BD vec enra | | Oo | . | 6 |
OPP ois i
| = | @ | at | . | 3 | o | ||
| i | wp | _£@ | Batt | newse | ~ | Ro | aes |
| a | By | ol | Mt | agusg | |||
| 2 | +5v— 20 | is} 2s] | |||||
| Reset [3 | $°dres | ee —1r | ne = | ||||
| =eSEy | 2 | ee, | 44] | 342 — | |||
| RESET | par (2* | Sena] Gt SETS) | | | 292 - | |||
| ENDSCREEN | - | De | RS | ||||
| 4 | soot 4S | [a py | 12 | pause |
PRie { pes}2% DBUSS: 1Ra DB4) 29 DBUse ves 2 pevs3 -& D2
| pert | SS PO | wey | He | pause |
aa
| oe [2 | ol | at | posi |
De e
+sY Ie} 26 ewe |Z a AK +59 3 Te ton
| 2 | oe | = | ||
| an | oe | - foo) | 93 | be |
| xe | a | ot | 862 |
ia
Ey
| a134 | up | iio | READ |
wafer £2, uf,
| TW | Te(warte>— | *[So8§—aai | |||
| O@OOOQS | Sy | 2 | 2H ES | oll | waite |
| Ea \y 8 | 12]93 | O-—— WRITE |
aaiw (ol) 7 Bg2 Weare, Figure 4-6 Microprocessor Circuitry (Part of 034634-XX _B)
4-10 Baseball™
+5v pt +5 -O1 PROM VERSION
| 45V | 45V | 45y | 45V | 45¥ | 45¥ | 45¥ | +50 | +5V 0 45V | 45v 0 45V 0 t5V | +5 |
ABUSsIO t if
| wr | eer | eer | [eer | fees | jeer | eer | eer | jeer | peer | eer | cer | Jee | fear | eer | [cer |
«| ko | zy | so | wi | wo | Mo | Le | fr | eo | en | em | pr | oe | co | ao ys [3474 [ost |oderra fosee] oss | os8e] 036725] 024724] 036717]034716) 03¢719]034720)094721/o34r22] 034725094724) Agus9 Aguss xs
| agus? | 17 | a | a1 |
Asuse——t Ae
| aguss | —2 | aS |
| agusa | ——3 | ae |
| aguss | —4I | As |
agusz——1 az
| agus) | —4! | AL |
Aause——3 Aen
| be—— | 03 | 93 | 3 | |||||||||
| 3 | ea | 8 | ray | |||||||||
| p¢—— | oy | ol | oe | |||||||||
| cer__feer | _|eez | [eer | [een | ceo__|ter_ | _leez | feez | [cez | [cer | [cer | eee | eer | |cez |
| SREP | RAR | RE | rol? Pol? |
++ + 4
-02 ROM VERSION
| a | Sv | +SV | +5V | |||
| Rs | aa | RS | Rel | |||
| jay | fae | far | fra | fer | [2a | do |
| es3 | 3 | 33 | ts3 | |||
| eB | Ni | Mi |
034735 | 034736 | 034737 | 034738
| Agusio | 2) | 10 |
| aguss | —22 | ao |
| ABUSE | 24 | As |
| ABUS7 | : | ar |
ABUS6 Ae
| ABUSS | 3 | as | |
| Agus4 | 4 | as | 9 |
| ABUS3 | 5 | aa | |
| ABUS? | cs | a2 | oO |
| Aausi | a | At | |
| ABUS® | ap | "7 |
o7 v7 Db te _ Db
| bs. | 1S | __ps |
dé pa D3] HS __ 3 bz Mpa DI Ho py
| de! | 2 | pe |
esics2 [est csa
| ye is |'2 | Jaojis |! | i |
Rom a
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFDENTIAL: ‘Reproduction forbisden. witnout. the Specilicwitten, permision "ot Atari ie.” Sunnwale, Gomme, Ths crewing 1s only conditional inaued, and nettner recalpt ner possession theroot confers or tana ary right invor license to use, the aoma drawing or any Sesign or tech thereon, nor any ont to reproduce iis drawing or any part thereo? except tormanutactore by vendore of Ata Incor nd for manutacture under the corporation's wi no ight to repredves this drawing Ws granted Orne aubjact matter tnereoruniess ty written agreemen Stith or welten permission from the corporation
Figure 4-7 Program Memory (Part of 034634-XX_ B)
Baseball™ 4-11
5, Watchdog reset counter A4 and associated circuitry (see Figure 4-6).
MPU, ROM, and RAM (See Figure 4-6, 4-7 and 4-8)
The microprocessor (MPU) is the “master controller” of all action that takes place in the game circuitry. Upon iniitialization, the MPU (via ABUSO thru ABUS15) addresses data locations in the program ROMs or PROMs. The data in the addressed locations is then read by the MPU via the 8-bit data bus (D0 thru D7). The MPU decodes this data to determine what action it is to perform next (i.e., “read coin switch 1”, “HIT”, etc.). The MPU uses RAM memory to temporarily store information which it will later recall. The MPU is capable of writing (or putting data into) the RAM and then later reading (pulling data out of the RAM, via address bus ABUSO thru ABUS15 and bi-directional data bus DO thru D7). Address Decoding Circuitry (See Figure 4-9)
The MPU address decoding circuitry performs the critical function of turning on or enabling the appropriate game circuitry (j.e., RAM, ROM, latches, etc.) at the correct time, so that information can be transferred back and forth between the game circuitry and the MPU. Tabie 4-1 is the memory map for this game.
© 0 Clock Driver (See Figure 4-6)
The basic operating frequency of the MPU is established by its & O input (on pin 37 of the MPU). The MPU runs at an operating frequency of 750 KHz. Examination of the MPU 2 output waveiorm (pin 39) with an oscilloscope should show a signal with a period of 1.33 microseconds.
NOTICE 70 ALL PERSONS RECEIVING TH!S DRAWING INTIAL i fen wilhou
9 rreteel en Por Ranatocture née the etpora o's Ro Sith wees permissin ton ihe cogorat oa
| ia | Sle, | es | 202 | RAMDe | sv | av |
—-e-Apr We 18 ie
| PS | pPe XevR | [3 | ramps |
| a | iz Re | M2 | NZ |
a i 90-1033| 90-1033
| = | isleo | po} %#—ramor | asvsio—2| | ao |
| agus | —'S | aa | on | |
| agusa | —e | roy | ||
| agus? | —!2 | arn | ||
| Aguse | — | ao | G |
aguss -—2 AS Apusa ——3} la
| ABuSs3 | —* | As |
| Apus2 | —t | Az |
awusi — la Aausé—S xy Lisa RAMD3 oa RAMDZ or} —Ramor yor f+ RaMDg
“tf =)
Figure 4-8 MPU RAM (Part of 034634-XX B)
4-12 Baseball™
| DUTPUTSEL | Ie | 3b — suTs | PROGSELI | js | 2. |
WRITE — u
| WRITE | yous! | ley | = 2p& | — 072 | oe? | Tt | )>2 | Rom |
| apusa—lag | tps — oom | 4 |
<7_ opt FERD —4 Roma ise 9320 “3b? inPorset—2de ——
| asusi | Bla, | 2p | NG | naive | |
| READ | 14) AD | 1 "at | _ | PROGSELG ————_} | a |
pecode Sp'2 nw vo) 432 — ROME MUK ABUSI!
re agusis——@ B —_ (oisPay BRSEL 1p 4 —> (wisea) Beye SEAR
> 2 DISRA asvsi¢ —'3] SOTPUTSEL asusi3 —!4 apusi2—!S |. )§ > warenvos INTAEK
NOTICE 10 ALL PERSONS RECEIVING THIS DRAWING
CONFIDENTIAL:
Figure 4-9 Address Decoding Circuitry (Part of 034634-XX B)
(The period of any periodic waveform is the measurement of the time it takes to complete one full cycle.) The 750 KHz clock outputs are generated by the 4H signal. This 4H frequency is generated by the horizontal sync counter R4 to produce the 0 clock input.
Watchdog RESET (See Figure 4-6)
The reset counter in the MPU control circuitry is a 4-bit decade counter, A4. The Qo output of this counter is the RESET signal to the MPU. Counter A4 counts the times the 128V signal changes states. On every high-to-low transition of 128V, the counter advances to the next count in its sequence. Meanwhile, the WATCHDOG signal, generated by the MPU at various times during its normal instruction sequence, is resetting the counter back to zero. If for some reason, the MPU program has strayed from its intended instruction sequence and the WATCHDOG signal does not occur before this counter counts up to a point where the Qo output goes high, a RESET signal is received by the MPU. The RESET signal causes the MPU to restart its instruction sequence from the beginning of the program.
Baseball™ 4-13
Table 4-1 Memory Map
MEMORY MAP
6000-7FFF PROGRAM a 5000. WATCHDOG. 4000-4003 INPUT PORTS 3000 INTERRUPT ACKNOWLEDGE {2000-2003 OUTPUT PORTS 1000-13BF. PLAYFIELD. _ MOTION OBJECT PARAMETERS 13C0 MOTION OBJECT 1 PICTURE # 13C1 MOTION OBJECT 1 VERTICAL POSITION 13E0 MOTION OBJECT 1 HORIZONTAL POSITION SPARE MOTION OBJECT 2 PICTURE # MOTION OBJECT 2 VERTICAL POSITION [| MOTION OBJECT 2 HORIZONTAL POSITION SPARE
MOTION OBJECT 16 PICTURE #
MOTION OBJECT 16 HORIZONTAL POSITION SPARE MOTION OBJECT 16 VERTICAL POSITION
03A0-03FF PLAYER 2 ALPHANUMERICS 0200-025F PLAYER 1 ALPHANUMERICS 0000-01FF WORKING RAM, INPUT/OUTPUT PORTS D6 DS D4 D3 D2 [ D1 ol) 2001 (OUTI) SPARE | Get SPARE NOISEN | HiT [WHISTLE COIN 2002 (OUT2) ATIRACT| CNTR NOISE AMPLITUDE
2003 (OUT3) SPARE LED CATHODES (4 BITS) 4000 (CTRED) -0 con 1 | Gen | SLAM [setect 1) PLIHD | PLIVD | PL2HD | pLzvp
| (INO) | (CTRLD)=1 | TRACK-BALL VERT. 1 | i: | TRACK-BALL HORIZ. 1 | |
| 4002 | (CTRLD)=0 | COIN2 | TEST | SPARE fetecr 27 | I | gens = | 7 |
| (IN2) | (CTRDD) =1 | TRACK-BALL VERT. 2 | TRACK-BALL HORIZ. 2 |
4-14 Baseball™
d. alphanumerics generator
(See Figure 4-10)
All score board information at the top and bottom of the TV monitor is generated by the alphanumerics generator. The information is actually generated by alphanumerics PROM N7. This PROM is addressed by latched MPU RAM. data signals RAMDO thru RAMD7.
The scoreboard picture components are each displayed as two side-by-side 8-line-by-4-bit blocks of video on the TV monitor screen. The MPU writes alphanumerics “picture select” data into the MPU RAM during 2. During 2, the MPU RAM is accessed by horizontal and vertical sync signals, a process referred to as direct memory access (DMA). The data output from the MPU RAM (RAMDO thru RAMD5, RAMD7) is latched and applied to the input of the alphanumerics PROM N7. This address information selects one of the 64 possible alphanumeric characters to be displayed. The actual line of the alphanumeric character to be displayed is defined by vertical sync signals 1V, 2V and AV and horizontal sync signal 4H. These four signals address the graphics PROM and cause it to either output a normal alphanumeric character or an “upside-down” alphanumerics character. This is done so that the two players’ scoreboards (on opposite sides of the screen) appear in the proper orientation. This inversion is controlled by HREFCNTL, which is generated by RAMD6 latched at the output of latch M7.
The data output of the alphanumerics PROM is applied to data selector/multiplexer N8. If horizontal reflect control signal HREFCNTL is low, the data is loaded into shift register P8 in the same order as output from the alphanumerics PROM. However, if HREFCNTL is high, the data input to shift register P8 is reversed. Therefore, HREFCNTL not only causes the TV monitor character to be inverted vertically, but it is also inverted horizontally.
Shift register P8 is loaded only during the period when HBLANK* and 256H" are both low. (This is the narrow strip at the top and bottom of the screen where the players’ scoreboard and other miscellaneous messages are displayed.) This results in a high ALPHASCAN signal that enables a load signal output from NAND gate N9 when both 1H and 2H are high. When 1H goes low P8 shifts four bits of the alphanumeric character out at a 6-MHz rate.
av HREFONTL, REFLay
REFLIV 2 HBLANK® og ALPHASCAN,
| 2 | 2 | 2sone Ud |
ee kere
| sv | +sv | w |
au wRercure uw [20 Be
| ce | 9. | NT | ||||
| ramo1—!Blep | aa | 3 [024710 | oMHe | |||
| RAMDe | Alin | sal | cet | Ar | ||
| 7 | we | ‘5 | RIB. | |||
| amps—Tip | ae | ase | ||||
| R | alr? m7 | 2]5 | wl | 8 | HREFENTL— | 2 |p |10 |
| aayds—S}20 | 7 29 | asd g | if | Fe Ky | ||
| f | a | aan | ||||
| Ramos-——4Jen | "Sah! | Wi a | vay, ? | aha ied |
LT oH, =
| RamDz—4sb**S"4ql® | tae & | al, | ay} | Up | ant? |
| nawoi—lsp — sal!2 | 2as | ¥ | re he | Ble Pe ae |
n 1
| rawog—Slen | 4a}? | Sina 2 | la | 10] | 21 | Beeches |
| oc. | neeLdy | 4) aa £04 | + | 38 NB | 4 A | ant? |
| Tyo | ae. | = os | Sia 8197 | 4 | SIL ¢ | ||
| ar | RerL2y | a2 5 | PS | 5 | 2 | 7 |
| Rt —t | el, | < 02 | 28 pata, | aa | ||
| REFLIV | ai | mn | al, | Seer | ||
| =. | she | t | ta | |e | eR | |
| : | exe | a8 | 24 | |||
| Ib Gio | 5 | iW | —2 {8952 |
rf TF pceunscan—H
- z \
far fight 1o reproguce this drawing 1s granted cor the subjsct mattor thereor Unless by watten agreement ‘with or written permission from the corporation, VIDEO INVERT
HBLANK, =H pLed@are, —Sd 02
Figure 4-10 Alphanumerics Generator (Part of 034634-XX B)
Baseball™ 4-15
Agusa—_t al apuse navy — 3} > ABUSE 7 uw 2] Leese agus ABUS4 4
Aguss—! ABUSt. £ +5v 25 ic 26 ToT + ma 4H ——+I
a n eay = DISAG
| aw | —S | P- | pooens |
fi 4 pisaa 2| Lszea fig
| PRo—e | tt | 2 | isa |
8 i }2— piso
| al | >- | fp | ocae |
| Oy | M4 | BB pisag | |
| cau | —_2| | 18204 | fis |
Aause: wt bissera 8H
16 Baseball™ DISSELA—
A 2G o1soat Pray bispes —2)2c2 9 yP— oi DISDID 2a Dist.
piso? —22co Lsis3 ahey bar Bisbag— A113 aa % wcz M
| ie | a | 12 | aise. |
SD16 es bisp]e —4Jico
piesers J
DISSELA—{ ia Sie afk 2] 7 pisp29— 2} aca or 1 2c2 pisbis eer Mf ose pisos —Phacd Zisa| pIsD2s eat DIsD2g. 7 r bISsDIZ wise orsD4
owses— LT
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction. forbidden without the Specitic written pormission at Atari inc., Sunnyvale. California. This drawing 1s only conditionally rssuec. and neither receipt nor possession thereof confers or wanalers any right in, or license to use, the subject malter ol ine Grawing of any design or technical information. shown thereon, nor any right to reproduce this drawing or any part thereat. excep for manufacture by vendors of Alar Incor porated and for manulacture under the corporation's wa fen license, no rght to reproduce ims drawing is granted fF the subject matter thereof unless by writien agreement wit or written permission trom the corporation. DISSELA — ba dis L afpe dispe7 —S)rc3 f <2
| a | aT fe | ay{? pies |
pispit ret DIsv3 2 [2°@ csisa| ‘ TA Disbee 5 103 Be ea DSBS DISse ispig—Sficr pispz —2Iico B16 Fr oiceete
DIssetA—j ie dis ala 2 oisD25, zea 2c
| ispr7—Ayrez | 4/9 | ge |
wisps Yc piso! —®l2c isis biso24— fica para] a] <> seup DISpie rea MUA pisos —fici
Diep 1 i Bio
Figure 4-11 Display RAM (Part of 034634-XX _B) ry pests
| ” | asuf | . | . | asv[ | L | * | + | + |
| ance {2 | eatst[ | eats | anv’ | as [tence | | aavsv[ + | ane |
abtede nlatetade lnletetede _|n Ee hoa InlateTebe Inbetetode Inlasfetene Ie hate tebe
| Ge | opt ar | ape yee | Uae | OPA aa | Ob er EO | EE | ob aT eee | oe |
| Kr | 32 | 42 | Fo | Ka | 74 | Ha | ||
| 90-7031 | 90-7031 | 90-7031 | 90-7031 | 90-1031 | 90-1031 | 90-7031 | 90-7031 | |
| DISAT | 2 | AT |
ae
| Dieae | —t | Se | @ioia-4)) |
DISsAS AS i
| DIsA4 | 2 | AS | |||||
| bisaa | —! | As | |||||
| DISAZ | 2 | az | |||||
| DIsAl | 5 | AL | |||||
| ‘ | bisag | —4 | he | ||||
| DBUST | ‘5 | Dis | 7 | pBvS3s | |||
| pBUSsE | 3 | DI | te) | DBUSZ | |||
| ' | Dauss | —1 | ore | “_ppusi | |||
| pBLS4 | 4 | Dri | > | DBUS® | |||
| S835F/Seesz/Aosg2 | (8 ss2) 884s | S88sz2/ | 82852 | ||||
| Bases | |ossae|sesaselssasa| | saad | Babe ag|a@sasa | ||||
| le Te Hz To feo lie [i fiz io 20 fe fie fiz fio f2o fie fia fiz Ie 2o fle id fiz | te fie [2 fio f20 | Ne id P No }20 | |||||
| | | I | t | 1 | ||||
| saggy | eggs | og ad | ut | song | gery | -8 | v=o |
| aAnaa | ag | gyre | rg | No | QPEL | reade | ww |
| Bhaag | 9443 | gadalzg | anaalfe S4hal® | Aaaa | aoaa|; | badale | |
| pegs | Q9OR)s | GBoavaze | vneasls | Faaalse | Qaow | gaoule | vaud |
| gvas | gaan | oo | Hees | vanue | oo | Ads wo | go |
| aaaga | Gado | GO6o|¥ | Gad0|/§ | 4040) | AaGoGOR | Oao45\ | AddOR |
NOTICE TO ALL PERSONS AECEIVING THIS ORAWING CONFIDENTIAL” Reprometion. forodden. wilnout tho Specille writen permession o! Atari, Ine.” Sunnyvale asy i California. This drawing is only conditionally issued. and nelthe receipt nor possession hereot canfersorransie's 4 ny right ino" heange to use, tne subject matte of te hn 20 Sito ay dein or tecalnfamaton shown Z
| inereo! except ter manulacture by Yengors of Atal neo | ois7—ad— | 3q/*& | pcr | |
| ' | porated ane for manulacture under the corporation's wit | 4 | E | |
| farang: rh ta veproduce ts amines ranted | vise | 2 | 20) | pice |
| thin or ween penssion om the corporavon | pise— | i770 ra& | pics |
Disa — 14 sane 15 pice e oss Bian? "bal! pics Pic2 Pic pice
#b-— DRAM D7 2 ome
| 12 | 1p BRANT | be |
mm —Sp 3
| are | > BEATE | __ | ||
| oeamwe | —He | 7 DT | = | = |
| 7 | seuss —“fa | SP | ba | |
| aausg —Sfa | SPE | bs |
spe Dz opt Dt 7 > De ea 8 it Decove” Po
Baseball™ 4-17
e. display ram
(See Figure 4-11)
The display RAM stores information from the MPU that defines the horizontal location, vertical location and picture of both the playfield objects (baseball diamond) and motion objects (players, ball and bat). The display RAM consists of four pairs of RAM devices, F2 and F4 (DRAMO), H2 and H4 (DRAM1), J2 and J4 (DRAM2) and K2 and K4 (DRAMS). Each pair contains 256 8-bit bytes of information.
The MPU addresses the display RAM during the ® 2 period (4H is low) through tri-state buffers L2 on address lines ABUS1 thru ABUS4 and ABUS6 thru ABUS9. The MPU selects the display RAM pair to be written to with address lines ABUSO and ABUS5, when DRAMWR goes low at the input of decoder E3. At this time data is written into the display RAM via data bus lines DBUSO thru DBUS7.
During the © 1 period (4H is low), the display RAM receives its address from either of two different sources. When.the TV monitor is actually scanning a horizontal line (256H is low), the display RAM outputs playfield data to the gtaphics generator. The graphics generator receives its data for playfield pictures when display RAM memory is directly accessed (DMA process) by horizontal and vertical sync signals through tri-state buffers L4. When the monitor is in horizontal blanking (256H is low), the display RAM outputs
4-18 Baseball™ motion object data to the graphics generator. The graphics generator receives its data from motion object pictures when the display RAM memory is directly accessed (DMA process) by horizontal sync signals through tri-state buffers M4.
The outputs of the display RAM ate selected by data selector multiplexers F3, H3, J3 and K3. These data selector multiplexers are controlled by the data selector multiplexer L3. During horizontal blanking (256H is low) and when 4H is low, display data (DISDO thru DISD7) is output to the graphics generator (for motion objects). During horizontal scan time (256H is high) and when 4H is low, horizontal sync 8H and vertical sync 8V select the data byte which is output to the graphics generator (for playfield objects). When 4H goes high, the MPU selects the display RAM data byte (via address lines ABUSO and ABUSS) which is output from the MPU. The display RAM is read by the MPU on data lines DO thru D7. Selected display RAM data is latched into tri-state latch E4 with each rising edge of 1H. When display RAM read DRAMRD goes low, the latched information appears at the DO thru D7 output of iatch E4.
The multiplexed data byte output D1SO thru D1S7 is latched at the output of latch D4 (PICO thru PIC7). This data byte of information contains the following: PICO thru PICS defines the actual playfield picture to be generated by the graphics generator. PIC6 (when high) reverses the generated picture horizontally. PIC7 (when high) reverses the picture vertically. oe pee
oa
/ING
f. graphics generator
(See Figure 4-12)
The graphics generator generates the video for the playfield (baseball diamond) during horizontal scan time. During horizontal blanking, the graphics generator generates the motion object signals (players, ball and bat) that are written into the motion object RAM.
For motion objects, display data DISD8 thru DISD15 from the display RAM defines the vertical scan line where there is a motion object to be displayed. When sync signals 8V thru 128V are equal to this number, at the next rising edge of 4H and MATCH signal is latched at the output of latch F6. At this time latch F6 outputs LINEO, LINE1 and LINE2. The binary count of LINEO thru LINE2 indicates which vertical line of the motion object picture is to be scanned.
The actual graphics pictures are stored in graphics ROMs C5 and D5. Address inputs PICO thru PICS from the display RAM define the actual picture to be output by the ROMs. The vertical line of the picture is defined by address inputs GA6 thru GA8. These signals originate from vertical sync signals 1V thru 4V for the playfield pictures. For the motion object pictures, these signals originate from the compared output of adder F5.
If PIC7 is low, the output of Exclusive OR gates D6 counts from 0 to 7. If PIC7 is high, the outputs of D6 count from 7 to 0. Therefore, PIC7 reverses the vertical order of the output graphics ROMs C5 and D5.
The data output from the graphics ROMs is applied to two data selector multiplexers B6 and C6. If the output is a motion object, B6 and C6 are enabled by MATCH at the input of OR gate K7. For a playfield object, B6 and C6 are enabled by 256H" (horizontal scan time). The inputs of B6 and C6 are arranged so that if PIC6 is low, the outputs are loaded into shift register A6 with graphics data GDO shifted out first and GD7 out last. If PIC6 is high, GD7 is shifted out first and GDO last. Therefore, PIC6 reverses the horizontal order of the graphics data output. Shift register A6 is loaded every 8H and shifted out at a 6-MHz rate. The output of A6 is inverted by B7 and applied to the motion object RAM data input. It is also gated with the playfield gate (PLFDGATE) signal at the input of AND gate K8. If PLFDGATE is high, it means that the horizontal scan is out of the area reserved for the alphanumerics generator and in the playfield area. Playfield video PLFDVID is applied to the video surnming circuitry. Motion object signals are applied to the input of the motion object RAM as RAWVID.
g. motion object ram
(See Figure 4-13)
The motion object RAM stores the video for sixteen 8-bitwide motion objecis, then outputs the object video bits in their proper locations during the time of scanning that horizontal line.
During the horizontal blanking period, display RAM data DISD16 thru DISD23 presets s binary counters J6 and K5 when HLD goes low. When HLD goes high, the counters increment their count output one count for each rising edge of 6 MHz. The count output is received by RAM K6 as its address input. For each count, one bit of motion data from the graphics generator is written into RAM K6. The counters increment their output seven counts, then HLD again goes low, presetting the counters with a new horizontal location number. This process is repeated seven times.
Shortly after the beginning of the horizontal scan period (256H is high), counters J6 and K5 receive a HCLR pulse that sets the count output to zero. When HCLR goes high, the counters begin counting from 0 to 255, again at a 6-MHz rate. At each address count, motion object data is output from the RAM to the video summing circuit.
Baseball™ 4-19
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
TC eR agy Li, OMnE 5 asy 2 ys au — is. ye 21 68 0
| nfo | = | 4 | RANT | P19 | wl“ | Re |
| lt | aS | rr | ¢ | weuR | bw | 470 |
| disp2a3—3]id | 1a} | eye | 8, | aot | Har he | |S |
| Disnzz—4f2» | 20 | he | ‘och | eer | wp | |
| 1 | af, | am | Ts | 3a] .° 40-7008 | ||
| prepa; | 4 | —}a utr 08| | As | |||
| prepeg—Ya | Sao cer OS | Yaa | ||||
| " | ee ca ox | 5 | ||||
| oisvia | —4} | Tee | a3 3 |
a7 is|,,
| dispig—2 | 4 | arg |
| pispry —3Y | a | Say © |
| pispie—4| | 3 | als |
3 cescen cea| Pa2-—4
is ap—dw a
| a | sp | chiara |
sf? cieak? fe r fe (aR: fe 4 5 S]B cua 08 4 onl cep cer ck. mod eri 2 Bore a
| Ei | 25ena | 2] 77 | FER |
8? soxs 8
| NOTICE 70 ALL PERSONS RECEIVING THIS DRAWING | toad —}Do5 | 16, |
GONFTOENTIAC: "Raproducton gtbidden wiht iso 14 il 6 Specie atten permission of Ata ine. “Sunnyvale
| Gaon Ths wing | ony contionay sued, ad | te | WCB |
‘eltha receipt nor possession thereo! confers ar tanaers Sny ght nor eenea to vse, the subject mater of te TSEHX drawing or any design or technical Inormation. shown itereon, nor any right to reatoduce this crewing or any part tnereol except tor manulactore by vendors a Ata Neer otated and for manutacture under the corpwration’s wri ten teense, 30 ght to reproduce this drawing is granted orthe subjact matter thereot unless by written agraement With or willen Bermission itom ine corboration
FRI I a0
| asenw—“]p | “ab? | —asenn | ||
| a | : | e7 | ||
| = | si¢ cle | ee | — ot | mere |
| aH | Yeu S"* a8 | —z5cne | acree | or |
cre id RAB
Figure 4-13 Motion Object RAM Circuitry (Part of 034634-XX B)
Baseball™ 4-21
h. video summing circuitry
(See Figure 4-14)
The video summing circuitry receives ALPHA from the alphanumerics generator PLFDVID (playfield video), from the graphics generator and MVID (motion object video) from the motion object RAM. These three signals are summed through various gates into flip-flops P9. The actual video to be displayed on the TV monitor is determined by the combination of the two signals at the outputs of flip-flops P9. These outputs (P9, pins 5 and 9) are mixed with HSYNC and VSYNC fox a composite VIDEO OUT signal.
NOTICE 10 ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction, Giivomiat this drawing 1s. only eonattionaly Issued, and neilher receipt nor possession Ihevea! confers artransts Any right ior heense To use, Ine subject matter of Ihe drawing or any design or technical infomation snow" {heed mor any lg to reroduge tis drawing oF any part there! excep! lor many aciu'a by Vendors ot Alar, Ineo” orated and for manutasture-urdor the corpavailon's wl fen license, no right to reproduce this drawing rs granted Srine subject mattur herent unless by whiten agreoment Swi or whiten permission from the serboration
VWetaNK VBLANK®
PRS
PLEDvIG —3, g!0 men __4 eye 2 a xePH —21N3 Yo > og 4 oma ne bmne New 3 Ra asy cf 2.2K 3 Az re gacimes YO F «veo PRB
out 21 al Pa omne—3fex gfe cre PLFDGATE, 7 i YecANKY — YiDEO PUFSVT RETURN RSYNC — TD 0 vsync —9102
Figure 4-14 Video Summing Circuitry (Part of 034634-XX_B)
4-22 Baseball™
i. switch and trak ball” input circuitry
(See Figure 4-15)
Player Trak Ball information, player switch inputs and the game option switches are read by the MPU on data lines DO thru D7. The three timing signals that control which inputs are read on which data lines, and when, are INO and IN2 from the address decoding circuitry and CTRLD from latch F8 that is shown on Figure 4-17.
When INO and CTRLD are both low, horizontal and vertical direction of both Trak Balls are read by the MPU on data lines DO thru D3 and player 1 switches are read on lines D4 thru D7. When INO is iow and CTRLD is high, the horizontal rate of player 1’s Trak Ball is read by the MPU on data lines DO thru D3. The vertical rate of player 1’s Trak Ball is read on lines D4 thru D7.
When IN2 and CTRLD are low, the game option switches are read by the MPU on data lines DO thru D3 and the switches for player 2 are read on lines D4 thru D7. When IN2 is low and CTRLD is high, the horizontal rate of player 2's Trak Ball is read on data lines DO thru D3. The vertical rate of player 2’s Trak Ball is read on lines D4 thru D7.
j. display pcb and coin counter
outputs (See Figure 4-16)
For a diagram of the display PCB, see Figure 4-3, Game Wiring Diagram.
The anode of all the game LEDs are strobed at the rate of 64V. The MPU lights an LED by first outputting data on bus lines DBUSO thru DBUS3. With the proper address from the MPU, OUTS goes low and latches the data at the output of latch F9. A high on any output causes its transistor to conduct.
The coin counter is tripped when the address decoding circuitry outputs a COIN CNTR signal. The high COIN CNTR signal causes QZ to conduct.
Baseball™ 4-23
- —— — — —- STEERING PcB-———— ~~
VTBL DIR PLIVD
vret cK
TREND edn ls in [KU DHS |,
| com | fie) | +$—+ | 2 | bs | “= | D7 | |
| ENDSCREEN | Ic usi91 aci® | ey | 2097 | |, | pe | |||
| Stam | [r | B | sync 98] | bs | |||
| 3 | al | > | [a | ||||
| ELECT I | [I7 | + | ~— | 'Slq | CNTR ga | i} | 4 |
| Mim | RP | ie | 16 |
~The 9 15
| Tse | > | Ror | Rot | SReO | a |
| NOK | 1OK | PIOK |
+8V
+5vV — P,R30 R53 SAS4
| Azrael oR | fy | + | PLnD |
H2TBI cK [3 ere [eas 1 Teor Ft
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL’ Reproauction lorvidden withoet. the spacitic written permission of Atar.. nc." Sunnyvale, California. this drawing is only conditionally issued, and neither receist nor possession thereat confers or tansiers any fight in, oF license to use, the subject malter of the ‘Grawing or any design or technical information shown thereon, nor any right to reproduce iis drawing or any part thereat ‘except for manulacture by vendors O1 Atari, Ineo and for mantiaciure undls the corporation's wnt erse, No right Le reproduce th’s Grawing is grante, fr the subicct matter thereol unless by wrilten agreement \with'or writen Dermission Irom the corporation
4-24 Baseball™ PLIHD PLIVD PLZRD PLAVD TTRUD to 2
| woulsaa = | LL, | nl | > | |a |
CK UD BY EI
| af, | ald | 2 | 10 | [3 |
| Dio | va] | 9097 | [ig | |
| vic | tSstat bade 3 | Fi | . | |
| B | swNc | 9B | ||
| IS], | <NTR gald | 4 | is | |
| Mim | RIP. | si ce | ||
| Tz | Fe | T | Os |
ine
Figure 4-15 Switch and Trak Ball Inputs (Part of 034634-XX_ B) D3 D2 DI vo
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: ‘Reproduction’ forbidden “without the walter, permission o} Atari. Inc. Sunnyvale, 1a This drawing #6 only conditionally ‘ssued, feceipt nor possession thereat confors oF tran Any right if, of license (o use, the subject matter of the Grawing cr any design ‘9r technical Information. shown thereon aor any right to reproguce this drawing of any patt theteo!, except for manufacture by vendors of Alavi, Incor porated and Tor manulactue under the corporation's wri. fen license, no “ant to reproduce this drawing is granted Ortine subject matter thereat uniess by written agreement ‘win Gr weteen permission trom the corporation. +sV
P.R30 asa SASS ihe
1OK S1OK . 3? >
| vre2 oe | [o | T | [>o+ | 4)0 | als | PLavD |
| vre2 cx fio} | i | “P>o2— | ||||
| cae | [eas | Ti0 | ||||
| ) | Jor | ax |
2eL
TPE
coma [g}_+—+ vest (is) 1 = EY
| SELECT | a(R | t | 13. |
io
| rPtera>—! | Ros | SRos | Ros | eos | al | Is] |
| 10K | SioK. | ie 26 |
s +sy — ie
+5
P,R30 R57 See iH
waT|a2 DIR PLaHD
W2TB2 CK
| | | edu ls do | ad |
Tid DU
| OPTION 4 | i | a | i | a | aot | eI | 2 | a | |
| options fa | ¢ | 1 | role | H2, | ace | al | [> | Js | ba |
t ns
| oerion2 | F7i | iS | r | 8 | eye a8 [2 | | | Lon |
| option: | 15[, | EnTR | gal?! | A | a | a |
Me RIP tie te ae
| = | RAB | Rso | Sasi | = | id | m__l' |
| 1K | 1oK | 10K | me |
Figure 4-15 (Continued) Switch and Trak Ball Inputs
Baseball™ 4-25
R27 COW CNTR aK, B r 4 Or
] !
t L 2NCoad ic COIN CATR,
Lio ENSeh4 FE} ANODE < R39 —+5v (OK ° R+o 2] 1 34 3 2 ms 2NSe44 fe] ANODE 8 1a Fy rev 7 ; nar sv
- + bead ia 5 10K = 6 R44
a DECODER’
R28
war!
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: ‘Reproduction forbiaten without the specific wiitlen permission of Alar. inc, Sunnysae, Gaitornia. Tris drawing is only conditionally issued. and either receipt nar possession thersol con ters orteanaters any right in, oF license to use, tne subject matter of the Grawing of any design or technical information shown, thereon. nar any right to reproduce this drawing ov any part ‘Rereof, exzept for manufacture by vendors of Ataf, incor porated ana Yor manulacture under the corporation's wnt en license, re right to reproduce this drawing is granted (or Ine Subject matter treieor unless By written agreement with of written permission trom the corporation 1K ANODE D
Rzs
33, u2W
ted a
Tepe
\4) TED CS 33,12w ae 2N3643
Figure 4-16 Display PCB and Coin Counter Outputs (Part of 034634-XX_ B)
4-26 Baseball™
k. audio circuitry
(See Figure 4-17)
The audio circuitry produces crowd noise, HIT and WHISTLE audio. The crowd sound is the result of the gated random noise generator composed of shift registers A8 and B8. The crowd sound volume is selected by the MPU through data bits DBUSO ihru DBUS3. The noise (unfiltered crowd sound) is filtered by the active bandpass filter circuit comprised of one quarter of op-amp A9 (LM324).
The HIT audio is generated from latched data signal DBUS1 from the MPU.
The WHISTLE sound is generated by timer C9 when DBUS0 is latched high.
The three sounds are summed at the input of op-amp A9 {one quarter of LM324) and fed to the volume control. The signal is then fed to the TDA2002 amplification circuit.
The ATTRACT signal is generated from the MPU via DBUSS input to latch E8. When ATTRACT is high, the audio signal is grounded by conducting transistor Q11.
Baseball™ 4-27
4-28 Baseball™ sv
Rat NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
‘x CONFIDENTIAL: Reproduetion lo*bidden. without The iten permission of Alar, Inc.” Sunnyvale.
‘drawing 3.6!
Raa
prs, pare opti naa tla ol cag 322K on oz [ o ey TER DBUST Sap aa\2 MIDEO INVERT = Is Tr
45v al
= WHISTLE
ato anaes ‘ ait os TM 324 100K
ATTRACT
ar {o%—arrracr
seu ERE goo x SPL
on
NOISE,
an ob) AUDIO GND
SE i vi 1 121% 2] aa
eoccnd Figure 4-17 Audio Circuitry (Part of 034634-XX_B)
illustrated parts catalog
The purpose of this chapter is to provide you with information for ordering replacement parts for your Baseball™ game.
When ordering parts from your distributor, give the part number, part name, applicable figure number of this catalog, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
Baseball™
5-2 Baseball™ ERT @ Figure 5-1 Final Assembly A034526-01 B NOTES: 46a 4OBREGD 32) Vj, aan Ra =?
- t ‘37,6 KEQD. % ) 8)
‘SECURE USING STAPLES (MIM. 8 PLACES)
APPLY R.TV SILICON RUBBER (GE, 108 OR
EQUIV) AS SHOWN.
(@) TAPE FULL LENGTH OF BEZEL FLAP TO FULL LENGTH OF SHIELD SUPPORT
LENGTH OF SHIELD SUPPORT.
A, 3M SEALANT (ITEM 34) IS TO BE APPLIED TO
WOOD SURFACE ONLY. FILL ENTIRE RECESSED
AREA. INSTALL GLASS & CHECK FOR SEAL ON
ALL 4'SIDES.
Baseball™ 5.3
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING
8 places, typical ground.
Attach green ground wires
as shown. INTERLICK hou pest
Figure 5-1 Final Assembly, continued
Figure 5-1 Final Assembly Parts List
A034504-01 Cabinet Assembly A009083-16 Coin Door Final Assembly. Consists of A006794-XX Coin Door Assy. and A006921-01 Harness Assy. For breakdown of Coin Door Assy. see Figure 5-2. Power Supply Assembly—see Figure 5-4 Cash Box Assembly, consisting of the following 3 items: Cash Drawer Cash Box Lid Cash Box Handle Control Panel Assembly—-see Figure 5-5 Glass Shield with Graphics Cardboard Bezel with Graphics 3AG 21/2-Amp. 250-Volt Slow-Blow Cartridge-Type Fuse Stop Panel Mounting Bracket Mesh Ventilation Grille Power Cord Assembly On/Off Switch Cover Baseball PCB Assembly—see Figure 5-8 Foam Vibration Damper Harness/Switch Assembly—see Figure 5-9 Monitor/Cash Box Guard 5-Inch 8-Ohm 5-Watt Speaker Speaker Grille Cash Box Bracket Interlock Switch Cover 3AB 3-Amp. 250-Volt Slow-Blow Cartridge-Type Fuse Rear Door Seal 23-Inch Diagonal Measure Black-and-White TV Monitor Monitor Tie-Down Bracket 2” Wide Black Adhesive Paper Tape Service Door Assembly 030868-01 Connector Mount TM-123 TEC Videoelectronics Monitor Service Manaul TM-124 Motorola Monitor Service Manual TM-125 Wells-Gardner Monitor Service Manual 006319-03 Copyright Decal 034537-01 Mesh Ventilation Grille 78-13025 3M Brand Sealant, 1/8” x 3/8” (3M Part No. EC-5354) 75-5520B #1/4-20 x 11/4” Round-Head Square-Neck Black Oxide Steel Carriage A007197-01 A007902-01 030244-01 006317-01 006445-01 A034533-01 033494-01 033493-01 46-2012502 033098-01 002728-01 004131-02 A033016-03 007103-01 A034634-01 034536-01 A034564-01 034497-01 48-004 000869-01 006870-01 007882-02 46-2023002 005233-01 92-030 005594-01 78-67032 A034534-01 Pee BEEN NEN NEE EE EE NN EEE eee
ios}
>
Bolt 75-0158 #1/4 Flat Plain SAE-Standard Regular-Pattern Steel Washer 75-990505S #1/4-20 Self-Locking Prevailing-Torque Shallow-Pattern Steel Hex Nut
ATARI’
5-4 Baseball™
Figure 5-1 Final Assembly, continued Paris List
SE 72-6610S #6 x 5/8” Cross-Recessed Pan-Head Type AB Zinc-Plated Steel Thread-Forming Screw 72-6812S #8 x 34” Cross-Recessed Pan-Head Type AB Zinc-Plated Steel Thread-Forming Screw 72-6810S #8 x 5/8” Cross-Recessed Pan-Head Type AB Zinc-Plated Steel Thread-Forming Screw 034509-16 #1/4-20 x 1” Socket Cap Countersunk Flat-Head Black Oxide Screw with Key Size of 0.156” Square. Thread-Locking Compound applied before Assembly. 75-935 2 #1/4-20 Steel Wing Nut 72-6012S #10 x 34” Cross-Recessed Pan-Head Type AB Zinc-Plated Steel Thread-Forming Screw 75-010S #10 Flat Plain SAE-Standard Regular-Pattern Steel Washer 75-0458 #1/4 Cortosion-Resistant Steel Split Lock Washer 75-915S #Y4-20 Standard Hex Patter Cadmium-Plated Steel Machine Nut 75-931 #10-24 Steel Wing Nut 75-5124B #10-24 x 11” Round-Head Square-Neck Black Oxide Steel Carriage Bolt 75-0408 #10 Corrosion-Resistant Stee! Split Lock Washer 72-6608S 4 #6 x Y/2” Cross-Recessed Pan-Head Type AB Zinc-Plated Sieel Thread-Forming Screw 75-5516B #1/4-20 x 1” Round-Head Square-Neck Black Oxide Steel Carriage Bolt 75-030S #10 Flat Plain SAE-Standard Wide-Pattern Steel Washer 75-5524B #1/4-20 x 11/2” Round-Head Square-Neck Black Oxide Steel Carriage Bolt 72-1406S #4-40 x 3/8” Cross-Recessed Pan-Head Type AB Zinc-Plated Steel Thread-Forming Screw
ATARI’
Baseball™ 5-5
(26)
- 2PLes
- 2PLcs
@) @) (s)
- 4PLcs (33)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction. forbidden without the specific written permission of Atari, Inc.. Sunnyvale, California. This arawing ie only conditionally issued, and ntneret contra mn ior drawing or thereot except for manufacture by vendors orated and for manufacture under the cor f raw by written agreement corpevation.
5-6 Baseball™
- 2PLes (3)
- 2PLcs
Figure 5-2 Coin Door Assembly A006794-16 thru -27 J ©
(2)2Pics (24) 2PLcs
- 2PLes
- 2PLes
- 4PLcs Not shown: @)2 tes A006921-01 Harness Assy.
Figure 5-2 Coin Door Assembly Parts List
Front Bezel Assy.—Used only on -16 Coin Door Assy. (25¢ ) Front Bezel Assy.—Used only on -17:Coin Door Assy. (5 Fr) Front Bezel Assy.—Used only on -18 Coin Door Assy. (1 DM) Front Bezel Assy.—Used only on -19 Coin Door Assy. (1 Kr) Front Bezel Assy.—Used only on -20 Coin Door Assy. (100 Y) Front Bezel Assy.—Used only on -21 Coin Door Assy. (10 pence) Front Bezel Assy.—Used only on -22 Coin Door Assy. (20¢ Australian) Front Bezel Assy.--Used only on -23 Coin Door Assy. (1 DM/2 DM) Front Bezel Assy.—Used only on -24 Coin Door Assy. (1 Fr) Front Bezel Assy.—Used only on -25 Coin Door Assy. (1 Baht) Front Bezel Assy.-—Used only on -26 Coin Door Assy. (1 DM/5 DM) Front Bezel Assy.—Used only on -27 Coin Door Assy. (100 Lire) For breakdown of Front Bezel Assy., see Figure 5-3 #6-32 x ¥%2” Cross-Recessed Pan-Head Cadmium-Plated Steel Tri- Fluted Thread-Forming Screw Coin Lockout Assembly Coin Switch Assembly Coin Counter Assembly Coin Door Weldment Key Loop Spring Return (used only on German DM coin doors) Bracket for Lock-Out Wires Right-Hand Lock-Out Wire Left-Hand Lock-Out Wire Scavenger Button Spacer (used only on German DM coin doors) Lamp Socket NEMA #47 Incandescent Miniature Bayonet-Base Lamp Carbon Spring Steel External Retaining Ring, for /4” Diameter Shaft #6-32 x V4” Cross-Recessed Pan-Head Cadmium-Plated Steel Tri- Fluted Thread-Forming Screw 75-99516 #6-32 Steel Nut and Spring Washer Assembly
- Quaniity of 15 is used on the German DM coin doors 008629-01 Spring 71-2118 Cam Lock, Hudson #CR73A045S 71-1225CU Coin Mechanism for American Quarter 71-1205FF Coin Mechanism for French 5-Francs Coin 71-1201MG ° Coin Mechanism for German 1-Mark Coin 71-1201KS Coin Mechanism for Swedish 1-Krona Coin 71-12100YJ Coin Mechanisrn for Japanese 100-Yen Coin 71-1210PE Coin Mechanism for English 10-Pence Coin 71-1220CA Coin Mechanism for Australian 20-Cent Coin 71-1202MG Coin Mechanism for German 2-Mark Coin 71-1201FF Coin Mechanism for French 1-Franc Coin 71-1201BT Coin Mechanism for Thai 1-Baht Coin 71-1205MG Coin Mechanism for German 5-Mark Coin 71-120100LI Coin Mechanism for Italian 100-Lire Coin A007637-16 A007637-17 A007637-18 A007637-19 A007637-20 A007637-21 A007637-22 A007637-23 A007637-24 A007637-25 A007637-26 A007637-27 300p ul0d Jad Ppasn asay} jo 2uQ,
wo 72-HA4608C
A030362-01 A030250-01 A002465-01 004320-01 004344-01 004340-01 004337-01 004338-01 004336-01 004326-01 006904-01 030257-01 70-11-47 73-3008 72-HA4604C NVNYEENNE PENNE EE NY
pexnbai se ‘100p w10o Jad pasn asay} jo Aue jo Z
<_
Baseball™ 5.7
Figure 5-2 Coin Door Assembly, continued Parts List
pion | reve | w, [___ teen
| 007753-01 | 1 | Anti-Probe Plate |
| A007638-01 | 1 | Slam Switch Assembly |
| 75-036S | 4 | #6 Flat Plain Wide-Pattern SAE-Standard Steel Washer |
| 73-3025 | 6 | Carbon Spring Steel External Retaining Ring, for 0.184” Diameter Shaft |
| 75-056 | 1 | #6 Internal-Tooth Steel Lock Washer |
| 033368-01 | 1 | Lock Bracket |
| 033369-01 | 1 | Lock Arm |
| 033371-01 | 1 | Slam Switch Insulator |
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden wilhout the pectic, watten, permission ‘ot Ati, inc.” Sunnyvale, ia’ This drawing 1s only condhianally issued, and iptnor possession thereot for transters for icense t0 use, er of the ‘of any design or technic shown Feon, nor any right 1o reproduce t par ing or any part thereol except for manulacture by vendors ol Ata, nor porated and for manulacture under the corporation's writ ten license, no right to reproduce this drawing is granted tr the subject maiter thereof uniess by written agreement ‘wun or written permission ‘ror the Corporation.
2PLCS
2PLCS
Figure 5-3 Front Bezel Assembly A007637-16 thru -27 G
5-8 Baseball™
Figure 5-3 Front Bezel Assembly Parts List
004328-02 1 Bezel 004330-02 Ring for American Quarter 004330-02 Ring for French 5-Franc Coin 009153-02 Ring for German 1-Deuischmark Coin 004330-02 Ring for Swedish 1-Krona Coin 009153-02 Ring for Japanese 100-Yen Coin 007752-02 Ring for English 10-Pence Coin 007752-02 Ring for Australian 20¢ Coin 030677-02 Ring for German 2-Deutschmark Coin 009153-02 Ring for French 1-Franc Coin 030677-02 Ring for Thai 1-Baht Coin 007752-02 Ring for German 5-Deutschmark Coin 030677-02 Ring for Italian 100-Lire Coin 004331-02 Coin Shield 004332-02 Primary Coin Chute 004327-01 Scavenger Button Bearing 004328-01 Price Plate Clamp 004343-01 Price Plate— 25 004343-06 Price Plate-—5 FR 004343-04 Price Plate—1 DM 004343-03 Price Plate—1 KR 004343-05 Price Plate—¥ 100 004343-02 Price Plate— 10 P 004343-07 Price Plate—20¢ Australian 004343-08 Price Plate—Einwurf 1 DM/2 DM 004343-09 Price Plate—1 FR 004343-10 Price Plate—1 Baht 004343-11 Price Plate—Einwurf 1 DM/5 DM 004343-12 Price Plate--100 Lire 73-3009 Carbon Spring Steel External Retaining Ring, for 3/8” Shaft Diameter 72-1604S 3 #6-32 x 1/4” Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 75-046 #6 Corrosion-Resistant Steel Split Lock Washer 72-CL606 #6-32 x 3/8” Phillips Pan-Head Steel “Rolok” Self-Threading, Thread-Rolling Machine Screw 75-046 #6 Internal-Tooth Steel Lock Washer >
JOOP UID Jed pasn asay} jo omy,
f
t
Oop Uloo Jed pasn asay} JO 2uD
ATARI
Baseball™ 5-9
4REQ’D
- 8 REQ’D mits
5-10 Baseball™ Figure 5-4 Type B Power Supply Assembly A007197-01 J NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction foridaan without the Specific. wrilten permission of Atati, Inc, Sunnyvate, Cation ne ‘rawing Is ori conaitionaly sued. ana 1h thereof contersortransters ipt nor possessio ty maht nor here to use. the Sub) drawing or any design or technical. information shown r ‘ior any right toreproduc
nse, no righ to repreduce ins drewing s grenied ject matter tnereol uniess by written agreement finer welten persssion om he corporation
Figure 5-4 Type B Power Supply Assembly Parts List
A009266-01 Power Supply Base Weldment Assembly A006886-01 Type B Transformer Termination Assembly 29-053 26,000 pf 15V Electrolytic Capacitor 78-70501SC 2” Diameter Cadmium-Plated Steel Component Mounting Bracket A006555-01 P.C. Board Rectifier 79-4411004 Panel-Mounting Non-Indicating 3AG Fuse Post 41-2003 115/250 VAC 5-amp 5-400 Hz AC Line Filter A006958-01 95V Voltage Selection Block (Black Wires) A006958-02 110V Voltage Selection Block (Orange Wires) A006958-03 205V Voltage Selection Block (Green Wires) A006958-04 220V Voltage Selection Block (Red Wires) 78-2708 Nylon Tape 6/6 Hole Bushing, 5/8” Inside Diameter x 55/64” Qutside Diameter x 1/4” Thick 72-1810S #8-32 x 5/8” Pan-Head Cross-Recessed Cadmium-Plated Steel Machine Screw 75-048 #8 Cortosion-Resistant Steel Split Lock Washer 75-918S #8-32 Standard Hex-Pattern Cadmium-Plated Steel Nut 75-0188 #8 Flat Plain SAE-Standard Regular-Pattern Steel Washer A007192-01 Power Switch Termination A007444-01 Power In Harmess 46-2038001 8-amp 125V 3AG Normal-Acting Fuse 46-2012501 2¥/2-amp 125V 3AG Slow-Acting Fuse
ATARI’
Baseball™ 5-11
. yoo FT] an vee da: (B)} 4 pea ‘ Ol aed pera 3
view EX (prom inside)
Figure 5-5 Control Panel Assembly A034533-01 B
5-12 Baseball™ (8)
1G) & RERID
NOTICE TO ALL PERSONS RECEIVING, THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the ‘written permission ol Atari, ‘This drawing i only conditi eipt nor possession thereot cor Any Tight In, oF Heenge to use, the subject matter of tne drawing cr any design or technical information shown thereon, nor any rightto repcoduce this drawing or any part ‘thereat, except for manufacture by vendors of Atari, Incorid for manulacture under the corporation's wr'treduce this drawing Is granted ‘hereo! unless by written agreement ‘transters:
or the subj wwith or written permission from the corporation,
Figure 5-5 Control Panel Assembly Parts List
OO A033360-01 Trak Ball™ Assembly — see Figure 5-6 A034565-01 Control Harness Assembly A033729-01 Play Select PCB Assembly — see Figure 5-7 034491-01 Metal Control Panel with Graphics 033097-01 Play Select Panel Support 034492-01 Acrylic Play Select Panel with Graphics 001856-01 Aluminum Bushing 75-990505S #1/4-20 Self-Locking Prevailing-Torque Shallow-Pattern Steel Hex Nut 75-5512N #Y/4-20 x 34” Round-Head Square-Neck Nickel-Plated Steel Carriage Bolt SPDT Momentary Pushbutton Switch, with Red Cap and Light-Emitting Diode #V/q Flat Plain SAE-Standard Regular-Pattern Stee] Washer #10 Corrosion-Resistant Steel Split Lock Washer #10-32 Standard Hex-Pattern Cadmium-Plated Steel Nut #10 Plain Fiat Regular-Pattern Steel Washer Black Single-Coated Adhesive Foam Tape, 44” wide x 1/8” thick NEMA #47 Incandescent Miniature Bayonet-Base Lamp #10 Fiber Washer Flat Nylon Washer, 0.470” inside diameter x 0.968” outside diameter x 0.075” thick WOH HH BEE
62-039 »
75-015S 75-0408 78-9108 75-010S 78-6900402 70-11-47 75-07053 75-07054 rualaanw
ATARI’
Baseball™ 5-13
2Pes
ee— 2PcsS
ZacS 2ZACS 2aes
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Ri th
either receipt nor possession thereat conters or transfers. any right in, oF license to use, the subject matter of the drawing or ‘any design or technical information sown, {ereon, nor any right fo reproduce this grawing or any part ept for manulacture by vendors of Atarl, incor: for manufacture under the corporation's wilt 2e right to reproduce this dawg is granted ct maiter thereof unless by written agreement with or written permission from the corporation.
5-14 Baseball™ nin
Ou
Figure 5-6 Trak Ball™ Assembly A033360-01 F wi
NOTICE 10 ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Beproauction forbidden without the Specitic written permission of Alar, inc, Sunnyvale, California. This drawing 18 oniy conditionally issued, and ner recelpt nar possession hercot confers or translers ight in, oF license tp use, the subject matter of the ‘or any detign or (echnical Information shawn sor an ight4o reproduce this dravting or any part te there! except for manslactuie By vendors of Ata, incor porated and for manufacture under the Corporation's wrt fen license, no rigm to repreduce this drawing 's granted ‘7 the subject malter there! Unless by welten agreernent ‘wan or wlttan permission from the corporation,
ay “x
2 FLACK.
We, 2s
Figure 5-6 Trak Ball™ Assembly Parts List
Base Plate Top Plate Cover Plate (Acrylic) Corner Post End Post Steering PCB Bracket Roller Shaft Stand-Off Adjustable Post Spacer Light Hub Trak Ball™ 033355-01 033356-01 033357-01 083358-01 033359-01 033361-01 033362-01 033363-01 033364-01 033365-01 000616-01 033366-01 RMR RE NNNE EEE
ATART
Baseball™ 5-15
Figure 5-6 Trak Ball™ Assembly, continued Parts List
a A 74-A00011 Phenolic Spacer, 1/8” inside diameter x 1/4” outside diameter x 1/4” long A009060-02 Printed Circuit Board Assembly 033367-01 Bearing 73-3006 Carbon Spring Steel External Retaining Ring, for 3/8” shaft diameter 72-8808 48-32 x 1/2” Hex Socket-Head Cap Steel Alloy Machine Screw 72-1006S #10-32 x 3/8” Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-1606S #6-32 x 3/8” Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-1408S #4-40 x 1/2” Cross-Recessed Pan-Head Cadmium-Plated Steel Machine Screw 72-8920S #3/8-16 x 11/4,” Hex Socket-Head Cap Steel Alloy Machine Screw 85-1808B #8-32 x 1/2” Socket Cap Flat Countersunk Head Black Oxide Steel Screw 75-3608S #6-32 x Y/2” Cross-Recessed Flat-Head Cadmium-Plated Steel Machine Screw #6 Corrosion-Resistant Steel Split Lock Washer #8 Corosion-Resistant Steel Split Lock Washer #10 Corrosion-Resistant Steel Split Lock Washer 43/8 Corrosion-Resistant Steel Split Lock Washer #10 Flat Plain SAE-Standard Regular-Pattern Steel Washer #8 Flat Plain SAE-Standard Regular-Pattern Steel Washer #6 Flat Plain SAE-Standard Regular-Pattern Steel Washer #4-40 Hex Shallow-Pattem Self-Locking Prevailing-Torque Corrosion- Resistant Steel Nut #6-32 Standard Hex-Pattern Cadmium-Plated Steel Machine Nut #3/8-16 Standard Hex-Pattern Cadmium-Plated Steel Machine Nut Label with Lubrication Instructions 75-046S 75-048S 75-040S 75-0418 75-010S 75-018S 75-016S 75-990504C RWNNHNOA
75-916S 75-919S 034168-01 Huw
ATARI”
5-16 Baseball™
TRACES SHOWN ARE ON OPPOSITE SIDE
esxecon a YAI9e\0_ 1ia8TOO4 10-OfSRE0 ey 70 IAAT?
@PL NOTICE TO ALL PEREONS RECEIVING THIS ORAWING SONTIDENTIAL’ Reproduction, forbidden. wimout the specific wat sono} ry Eatiornia.
i ight to reproduce this drawing Is grantee rine subject mater thereo! uniess by writen agreement WHR OF wntten Dermission from the corporation,
¢ =D a =>) i {
[21
SCHEMATIC
Figure 5-7 Play Select PCB Assembly A033729-01 A
Light-Emitting Diode with Red Diffused Cap: 1.6 mcd, 20 mA, 1.7 Volts (MV5053) CR1-4 NEMA T-3/ Right-Angle PCB Mounting Miniature Bayonet-Base Lamp Socket Right-Angle Header with 7 Contacts
ATARI’
Baseball™ 5-17
tt
Cl
5-18 Baseball™ 5974 8: (0)
Figure 5-8 Baseball PCB Assembly A034634-01 and -02 A NOTICE TO ALL PERSONS AECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atari, Inc... Sunnyvale, Gaifornia’ Ths drawing |s only conéitionally issued, and either receipt nor, fon thereo! confers or transfers any right in, or Heense 10 use, ‘drawing or any assign or {thareon, nor any right to reprodcoe this drawing of any part "or manulacture oy Vendors of atari, Incor-
with oF written permigsian trom the co:poration,
10-5152 10-5222 10-5392 10-5562 10-5103
10-5223 10-5473 10-5563 10-5104 10-5224 10-5334 10-5394 11-5330 10-5390 10-51P0 19-315503
19-10020001 24-250106 24-250108 24-250477 24-250228 10-5181 10-5474 27-250102 27-250103
27-250104 Breage
Mee BHR OD
BrP REENHWH Figure 5-8 Baseball PCB Assembly Parts List
100 Ohm, +5%, ¥4W Carbon Composition Resistor 330 Ohm, +5%, %W Carbon Composition Resistor 470 Ohm, +5%, %W Carbon Composition Resistor 1K Ohm, +5%, 1/4W Carbon Composition Resistor
1.5K Ohm, +5%, 14W Carbon Composition Resistor 2.2K Ohm, +5%, 1/4W Carbon Composition Resistor 3.9K Ohm, +5%, 1/4W Carbon Composition Resistor 5.6K Ohm, +5%, 14W Carbon Composition Resistor 10K Ohm, +5%, %W Carbon Composition Resistor
22K Ohm, +5%, '/4W Carbon Composition Resistor 47K Ohm, +5%, ¥/4W Carbon Composition Resistor 56K Ohm, +5%, 1/4W Carbon Composition Resistor 100K Ohm, +5%, 14W Carbon Composition Resistor 220K Ohm, +5%, 14W Carbon Composition Resistor 330K Ohm, +5%, %4W Carbon Composition Resistor 390K Ohm, +5%, %4W Carbon Composition Resistor 33 Ohm, +5%, 1/2W Carbon Composition Resistor 39 Ohm, +5%, ¥%4W Carbon Composition Resistor 1 Ohm, +5%, 14W Carbon Composition Resistor 50K Ohm Vertical PCB-Mounting Cermet Trimpot (Boumes Series 3352V-1-50K) 2 Ohm, + 10%, 20W Wirewound Resistor 10yf Electrolytic Radial-Lead Capacitor 1000yf Electrolytic 25V Radial-Lead Capacitor 470uf Electrolytic 25V Radial-Lead Capacitor 2200p Electrolytic 25V Radial-Lead Capacitor 180 Ohm, +5%, %4W Carbon Composition Resistor 470K Ohm, +5%, 1/4W Carbon Composition Resistor 0.001pf Ceramic-Dise 25V Radial-Lead Capacitor 0.01 Ceramic-Dise 25V Radial-Lead Capacitor
O.1pt Ceramic-Disc 25V Radial-Lead Capacitor
ATART R7, 8, 21 R23, 26 RI, 2, 6, 9, 11-13, 18, 27-31, 40, 43, 44, 67, 68, 76, 78,
R22 R19, 32-34, 84 R20 R72 R10, 39, 41, 42, 48-65, 77 R36 R74, R15 R14, 82 R16, 70, 73 R71 R17 R24, 25, 66, 69 R86 R85 R75
R37 C35, 50, 69
C27, 28, 38-41, 48, 49, 51-53, 68,
C1-11, 13-22, 24-26, 29-31, 36, 37, 42-46, 66, 67, 70, 72
Baseball™ 5-19
27-250224 28-101101 21-101103 21-101223 31-1N4001 31-A14F 32-1N5242B 33-2N3644 34-2N3643, 34-2N6044 37-7400
37-7402
37-7404 37-7408 37-7410
37-7414
37-7430 37-7432
37-7442
37-7474
37-74S74
37-74LS83
37-74LS86
37-7490 37-74LS153
37-74LS157
37-74LS163A.
37-74LS 164
5-20 Baseball™ NE VwWHEN OEE Ee Figure 5-8 Baseball PCB Assembly Parts List
0.22uf Ceramic-Disc 25V Radial-Lead Capacitor 100pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor 0.01pf Radial-Lead Epoxy-Dipped 100V Mylar Capacitor 0.022yf Radial-Lead Epoxy-Dipped 100V Mylar Capacitor 50V Silicon Rectifier 1N4001 Diode 50V 2.5A Miniature Axial-Lead High-Current Rectifier 12V, +5%, 500mw Zener Diode, Type 1N5242B PNP Silicon Transistor, Type 2N3644. NPN Silicon Transistor, Tykpe 2N3643 Darlington NPN Transistor, Type 2N6044 Type 7400 TTL Quad 2-Input NAND Gate Integrated Circuit Type 7402 TTL Quad 2-Input NOR Gate Integrated Circuit Type 7404 TTL Hex Inverter Integrated Circuit Type 7408 TTL 2-Input AND Gate Integrated Circuit Type 7410 TTL Triple 3-Input NAND Gate Integrated Circuit Type 7414 TTL Hex Schmitt Trigger Inverter Integrated Circuit Type 7430 TTL 8-Input NAND Gate Integrated Circuit Type 7432 TTL Quad 2-Input OR Gate Integrated Circuit Type 7442 TTL 4-to-10 BCD-to-Decimal Integrated Circuit Type 7474 TTL Dual-D Edge Trigger Flip-Flop Integrated Circuit Type 74874 TTL Dual-D Edge Trigger Flip-Flop Integrated Circiut Type 74LS83 TTL 4-Bit Binary Full Adder Integrated Circuit Type 74LS86 TTL Quad 2-Input Exclusive OR Gate Integrated Circuit Type 7490 TIL Decade Counter Integrated Circuit Type 74.5153 TTL Dual 4-line-to-1-line Data Selector/ Multiplexer Integrated Circuit Type 74LS157 TTL Quad 2-line-to-1-line Data Selector/ Multiplexer Integrated Circuit Type 74LS163A TTL Synchronous 4-Bit Counter Sync Clear Iniegrated Circuit Type 74LS164 TTL 8-Bit Serial-In/Parallel-Out Shift Register Integrated Circuit
ATARI C47 cl2 C33 C34 CR4-8 CR1, 2 CR3 Q5-7 Ql, 3, 4, 8-11
P2, N4, P7 D8, L8 J7, N9
D3, B7, J10
H6 M3, P3, B4, C4, BS B3, E3, L10
N5, E9, J9, M9, PQ L7
F5, HS
D6, A7, M8
A4 F3, H3, J3, K3 L3 B6, C6, E6, N8,
Figure 5-8 Baseball PCB Assembly, continued Parts List
37-74LS166 Type 74LS166 TTL 8-Bit Shift Register Integrated Circuit 37-74LS174 Type 74LS174 TTL Hexadecimal D-Type Flip-Flop Integrated Circuit 37-74LS175 Type 74LS175 TTL Quad D Flip-Flop Integrated Circuit
| 37-74LS191 | Type 74LS191 TTL Synchronous Binary Up/Down | D9, H9, D10, H10 |
Counter Integrated Circuit
| 37-74195 | Type 74195 TTL 4-Bit Parallel-Access Shift Register | P83 |
Integrated Circuit
| 37-74LS244 | Type 74LS244 TTL Octal Buffers and Line Drivers | C1, E2, L2, N3, |
Integrated Circuit L4, M4
| 37-74LS374 | Type 74LS374 TTL Octal D Flip-Flop Tri-State | D4, E4, J5, F6, |
Integrated Circuit M7, F8 37-LM323K 3-Amp. 5V Positive Voltage Regulator
| 37-LM324 | Type LM324 Linear Quad Operational Amplifier | AQ |
Integrated Circuit
| 37-555 | Type NE555 Timer Integrated Circuit | co |
37-TDA2002AV | Type TDA2002AV 8W Linear Audio Ampiifier Integrated Circuit
| 37-8T28 | Type 8T28 TTL Non-inverting Out Tri-State Quad Bus | E5, E7 |
Receiver Integrated Circuit 37-9316 Type 9316 TTL 4Bit Binary Counter Integrated Circuit | M5, P5, M6, N6, P6
| 37-9321 | Type 9321 TTL Dual 1-of-4 Decoder/Demultiplexer | C7 |
Integrated Circuit
| 37-8097 | Type DM8097N TTL Tri-State Hex Buffer Integrated | E10, E/F10, |
Circuit F/H10
| 62-001 | SPST Pushbutton Switch | AS |
| 66-114Pi1T | 4-Station Single-Throw Dual-Inline-Package Bit Switch | K10 |
72-1608C #6-32 x V2” Cross-Recessed Pan-Head Corrosion- Resistant Steel Machine Screw 75-016C #6 Flat Plain SAE-Standard Regular-Patiern Corrosion- Resistant Steel Washer 75-056C #6 Internal-Tooth Stainless Steel Lock Washer 75-916C #6-32 Standard Hex-Pattern Corrosion-Resistant Steel Nut 72-1604C #6-32 x 1/4” Cross-Recessed Pan-Head Corrosion- Resistant Steel Machine Screw 78-16005 Thermal Conductive Compound, Berquist #7403-10-04 78-06001 Flat Black Anodized Aluminum Heat Sink 009470-01 Heat Sink 034815-01 Heat Sink
ATART
Baseball™ 5-21
Figure 5-8 Baseball PCB Assembly, continued Parts List
40-Contact Medium-Insertion-Force IC Socket 73-7A0509C Oval-Head Semi-Tubular Corrosion-Resistant Stainless Steel Rivet, 5/32” Shank Diameter x 9/32” Shank Length 90-102 12.096 MHz, + .005%, Crystal 020670-01 Test Points
| 90-6010 | Microprocessor | c2 |
| 90-7008 | Type 82S16 256 x 1 Bipolar Random-Access Memory | K6 |
Integrated Circuit
| 90-7031 | Type 2101A-4 MOS 256 x 4 Static Random-Access | F2, H2, J2, K2, |
Memory Integrated Circuit (450 ns) F4, H4, J4, K4 90-7033 Type 2114 MOS 1024 x 4 Static Random-Access Memory Integrated Circuit (450 ns) 034006-01 Programmable Read-Only Memory (Sync) 034710-01 Programmable Read-Only Memory {Alphanumerics) 034708-01 Programmable Read-Only Memory (Graphics/LSB) 034709-01 Programmable Read-Only Memory (Graphics/MSB)
For remaining memory components and their part numbers, see next page.
5-22 Baseball™
Figure 5-8 Baseball PCB Assembly, continued
Alternate -01 P.C. Boards (PROMs) -01 P.C. Boards (PROMs)
034720-01 EO (ROMs)
034735-01 P1
034736-01 N1
034737-01 M1
034738-01 NO | -02 P.C. Boards
Baseball™ 5-23
By)
FUSE BLOCK
A034563-01 A034631-01 68-002 000268-02 A030169-01
030168-01 69-001 72-6008S
19-9032
79-3210
5-24 Baseball™ Buea)
- INTERLOCK
NO. 2PLES 2PLCS we 82 w BK ex ON/OFF
Ww We 6) rr 8K ‘/BN. W W ! S i] LI ! D
ek w INTERLOCK
BN(K2)
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING, specitie wiltlen permission ol Aten, inc. Sunnyvale, Eaivorna’ This ofawing tp only conditionally Issued, and neither receipt nor possession tnereot confers or transters ary ron i. or Hicense to use, the subiest matter 3 the rai ‘design oF technical information. shown thereo fara igh 0 saproduse\his rawingo any gr Dy vendors ol Atari, Ineo der the corporavon's wi his drawing is granted Subject matter tneroot unless by wntten agreement ‘wat oF written permission from "he corporation,
Figure 5-9 Harness/Switch Assembly A034564-01
Main Harness On/Off Switch Assembly DPDT Interlock Switch, Cherry #E79-30A Interlock Switch Mounting Bracket Audio Control/Test Switch Assembly (Rev. G), consisting of the following four items: Mounting Bracket DPDT Slide Switch, Switchcraft #46206LR #10 x 1” Cross-Recessed Pan-Head Type AB Zinc-Plated Steel Thread-Forming Screw Wirewound Panel-Mounting Variable Resistor, Ohmite Model E, #0110 Rheostat Single-Pole .25” Quick-Disconnect Tab Fuse Block
_ oe Cut along this line
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm 0 Distributor 1 Operator Address (1 Other.
City State Zip
TM-135, Ist printing
First fold |
No Postage Necessary if mailed in the United States
BUSINESS REPLY MAIL
FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA
POSTAGE WILL BE PAID BY ADDRESSEE
Atari, Inc. Attn: Publications/Coin-Op Eng. P.O. Box 427 Sunnyvale, California 94086
Second fold
o g a
Cut along this line
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
@ PEGE GE RET ES
BX Ren TEN EN AON BEN OES
WARRANTY
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period. provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller’s examination of said products discloses to Seller’s satisfaction that such alleged defects existed’ and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order. = S © © © :
Piles Nata Nate Satie Mates Naas Satie ated Saha
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
A.
ATARI
ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 * TELEX 35-7488 > wore: communications Company