CATHODE RAY TOMES

18 Wheeler DLX

18 Wheeler: American Pro Trucker (deluxe, Rev A) (Sega, 2000) · Manual · 147 pages · 255 sections · original scan

Page 1

dot ABERIAN PRO PRIRER yea

DELUXE VERSION

OWNER’S MANUAL

SEGA ENTERPRISES, INC. USA MANUAL NO. 4201-6545-01

Page 2

VISIT OUR WEBSITE!

| Sherlock Preferences | Larger Smaller i

+ Dari's Office «Game Manuals *“Seerenh oWhoet's New

556 4Boeag have visited this page since 3/16/01

ones one in If you have any questions or comments

Service Department 4

Preiep nya about this site please E-Mail to Darl Davidson@seu sega com

tax 415.701 0604

THOR WER BUTE POwENEO OY

WebSTAR 4-3

You will need the ot items to view this = in its entirety

AllPlatforms Windows Macintosh

Page 3

TABLE OF CONTENTS

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS

INTRODUCTION OF THE OWNER'S MANUAL

HANDLING PRECAUTIONS PRECAUTIONS CONCERNING INSTALLATION LOCATION .. OPERATION ....

NAME OF PARTS.

ACCESSORIES ....

ASSEMBLING AND INSTALLATION...

PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE .

CONTENTS OF GAME

EXPLANATION OF TEST AND DATA DISPLAY

9-1 SWITCH UNIT AND COIN METER.......

9-2 SYSTEM TEST MODE...

9-3 GAME TEST MODE...

  • CONTROL PANEL(HANDLE MECHA, 10 - 1 REMOVING THE HANDLE MECHA...

10 - 2 VOLUME ADJUSTMENT/REPLACEMENT ..

. SHIFT LEVER

11 - 1 REMOVING THE SHIFT LEVER

11 - 2 SWITCH REPLACEMENT

  • ACCELERATOR & BRAKE ... 12 - 1 REMOVING THE ACCELERATOR AND THE BRAKE

12 - 2 ADJUSTING OR REPLACING THE VOLUME...

12-3 GREASING..

  • COIN SELECTOR
  • PROJECTOR

14-1 CLEANING THE SCREEN

14-2 ADJUSTMENT OF TOSHIBA PROJECTOR,

14-3 ADJUSTMENT OF MITSUBISHI PROJECTOR ...

  • REPLACING THE FLUORESCENT LAMP,AND LAMPS.
  • PERIODIC INSPECTION TABLE
  • TROUBLESHOOTING
  • GAME BOARD .....

18 - 1 REMOVING THE BOARD ...

18 - 2 COMPOSITION OF GAME BOARD

18 - 3 ERROR DISPLAY(DRIVE CONTROL BOARD)

  • DESIGN RELATED PARTS...
  • PARTS LIST ..
  • WIRE COLOR CODE TABLI
  • WIRING DIAGRAM ..... Mw Pender

SPN

94 ~139

Page 4

SPECIFICATIONS

Installation space:1,580mm (W) X 2,460 mm (D)

(62.2 in. X 96.9 in.)

Height:2,230 mm (1045.0 in.)
Weight:Approx.474 kg. (743.0 Ibs.)
Power, maximum current:680 W 7.63 A (AC 110V 50 Hz AREA)

660 W 7.39 A (AC 110V 60 Hz AREA) 650 W 6.79 A (AC 120V 60 Hz AREA) 700 W 3.90 A (AC 220V 50 Hz AREA) 690 W 3.89 A (AC 220V 60 Hz AREA) 720 W 3.94 A (AC 230V 50 Hz AREA) 700 W 3.80 A (AC 230V 60 Hz AREA) 690 W 3.61 A (AC 240V 50 Hz AREA) 660 W 3.44 A (AC 240V 60 Hz AREA) For TAIWAN (MITSUBISHI PROJECTION DISPLAY TYPE)

Power, current:680 W 8.00 A (MAX.)

300 W 3.40 A (MIN.) For TAIWAN (TOSHIBA PROJECTION DISPLAY TYPE)

Power, current:705 W 8.10 A (MAX.)

310 W 3.60 A (MIN.)

MONITOR:50TYPE PROJECTION DISPLAY

INTRODUCTION OF THE OWNER'S MANUAL

This Owner's Manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electromechanicals, servicing control, spare parts, etc. as regards the product, EIGHTEEN WHEELER DELUXE. This manual is intended for the owners, personnel and managers in charge of operation of the product. Operate the product after carefully reading and sufficiently understanding the instructions. If the product fails to function satisfactorily, nontechnical personnel should under no circumstances touch the internal system. Please contact where the product was purchased from.

Use of this product is unlikely to cause physical injuries or damages to property. However, where special attention is required this is indicated by a thick line, the word "IMPORTANT" and its sign in this manual.

Indicates that mishandling the product by disregarding this display can cause the product's intrinsic performance not to be obtained, resulting in malfunctioning.

IMPORTANT

SEGA ENTERPRISES, INC. (U.S.A.)/CUSTOMER SERVICE 45133 Industrial Drive, Fremont, California 94538, U.S.A. Phone : (415) 701-6580 Fax : (415) 701-6594

Page 5
WARNING! Non-technical personnel who do not have technical knowledge and expertise should refrain from performing such work that this manual requires the location's maintenance man or a serviceman to carry out, or work which is not explained in this manual. Failing to comply with this instruction can cause a severe accident such as electric shock.

Ensure that parts replacement, servicing & inspections, and troubleshooting are performed by the location's maintenance man or the serviceman. It is instructed herein that particularly hazardous work should be performed by the serviceman who has technical expertise and knowledge.

The location's maintenance man and serviceman are herein defined as follows:

"Location's Maintenance Man" : Those who have experience in the maintenance of amusement equipment and vending machines, etc., and also participate in the servicing and control of the equipment through such routine work as equipment assembly and installation, servicing and inspections, replacement of units and consumables, etc. within the Amusement Facilities and or locations under the management of the Owner and Owner's Operators of the product.

Activities of Location's Maintenance Man : Assembly & installation, servicing & inspections, and replacement of units & consumables as regards amusement equipment, vending machines, etc.

Serviceman : Those who participate in the designing, manufacturing, inspections and maintenance service of the equipment at an amusement equipment manufacturer. Those who have technical expertise equivalent to that of technical high school graduates as regards electricity, electronics and or mechanical engineering, and daily take part in the servicing & control and repair of amusement equipment.

Serviceman's Activities : Assembly & installation and repair & adjustments of electrical, electronic and mechanical parts of amusement equipment and vending machines.

Page 6
  • HANDLING PRECAUTIONS

A

WARNING!

IMPORTANT

When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely. Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine.

Before performing work, be sure to turn power off. Performing the work without turning power off can cause an electric shock or short circuit. In the case work should be performed in the status of power on, this manual always states to that effect. To avoid electric shock or short circuit, do not plug in or unplug quickly. To avoid electric shock, do not plug in or unplug with a wet hand. Do not expose Power Cords and Earth Wires on the surface, (floor, passage, etc.). If exposed, the Power Cords and Earth Wires are susceptible to damage. Damaged cords and wires can cause electric shock or short circuit.

To avoid causing a fire or electric shock, do not put things on or damage

Power Cords. When or after installing the product, do not unnecessarily pull the power cord. f damaged, the power cord can cause a fire or electric shock. n case the power cord is damaged, ask for replacement through where the product was purchased from or the office herein stated. Using the cord as is damaged can cause fire, electric shock or leakage. Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock. Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause a fire or electric shock. Completely make connector connections for IC BD and others. Insufficient insertion can cause an electric shock. Specification changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted.

Failure to observe this may cause a fire or an electric shock. Non-compliance with this instruction can have a bad influence upon physical conditions of the

players or the lookers-on, or result in injury during play. SEGA shall not be held responsible for damage, compensation for damage to a third party, caused by specification changes not designated by SEGA. Be sure to perform periodic maintenance inspections herein stated.

For the IC board circuit inspections, only the logic tester is allowed. The use ofa multiple-purpose tester is not permitted, so be careful in this regard. The Projector is employed for this machine. The Projector's screen is susceptible to damage, therefore, be very careful when cleaning the screen. For details, refer to PROJECTOR.

Page 7
  • PRECAUTIONS CONCERNING INSTALLATION

LOCATION

avoid installing in places mentioned below so as not to cause a fire, electric shock, Ay This product is an indoor game machine. Do not install it outside. Even indoors,

WARNING! injury and or malfunctioning. @ Places subject to rain or water leakage, or places subject to high humidity in the proximity of an indoor swimming pool and or shower, etc. @ Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc. Places filled with inflammable gas or vicinity of highly inflammable/volatile chemicals or hazardous matter. Dusty places. Sloped surfaces. Places subject to any type of violent impact. Vicinity of anti-disaster facilities such as fire exits and fire extinguishers. The operating (ambient) temperature range is from 5° C to 40° C. Only in the case a projector is employed, the temperature range is from 5° C to 30°C.

LIMITATIONS OF USAGE REQUIREMENTS

Be sure to check the Electrical Specifications. Ensure that this product is compatible with the location's power supply,

WARNING! voltage and frequency requirements. : A plate describing Electrical Specifications is attached to the product.

Non-compliance with the Electrical Specifications can cause a fire and

electric shock. This product requires the Breaker and Earth Mechanisms as part of the

location facilities. Using them in a manner not independent can cause a fire

and electric shock. Ensure that the indoor wiring for the power supply is rated at 15A or higher (AC single phase 100 ~ 120V area), and 7A or higher (AC 220 ~ 240V area).

electric shock. Be sure to independently use the power supply equipped with the Earth Leakage Breaker. Using a power supply without the Earth Leakage Breaker can cause an outbreak of fire when earth leakage occurs. Putting many loads on one electrical outlet can cause generation of heat and a fire resulting from overload. When using an extension cord, ensure that the cord is rated at 15A or higher (AC 100 ~ 120V area) and 7A or higher (AC 220 ~ 240V area). Using a cord rated lower than the specified rating can cause a fire and electric shock.

Page 8

OPERATION AREA

A

WARNING!

So @ For the operation of this machine, secure a minimum area of 2.905m (W) X 2.56m (D). In order to prevent injury resulting from the falling down accident during game play, be sure to secure the minimum area for operation. Be sure to provide sufficient space so as to allow this product's ventilation fan

to function efficiently. To avoid machine malfunctioning and a fire, do not

place any obstacles near the ventilation opening. SEGA shall not be held responsible for damage, compensation for damage to a third party, resulting from the failure to observe this instruction.

For transporting the machine into the location's building, the minimum necessary dimensions of the opening (of doors, etc.) are 1.6m(W) and 1.7m(H).

IMPORTANT

— Electric current consumption + wy

MAX. 7.63 A (AC 110V 50 Hz) Y MAX. 7.39 A (AC 110V 60 Hz) A 10cm MAX. 6.79 A (AC 120V 60 Hz) or MAX. 3.90 A (AC 220V 50 Hz) MAX MAX MAX MAX MAX MAX

MAX MITSUBISHI projection display)

TOSHIBA projection display) _ 3.89 A (AC 220V 60 Hz) _3.94 A (AC 230V 50 Hz) _3.80 A (AC 230V 60 Hz) _3.61 A(AC 240V 50 Hz) _3.44 A (AC 240V 60 Hz) [ os _ 8.00 A (For TAIWAN,

. 8.10 A (For TAIWAN,

2.905m

FIG. 2

Page 9
  • OPERATION

PRECAUTIONS TO BE HEEDED BEFORE STARTING THE OPERATION

To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

In order to avoid accidents, check the following before starting the operation: @ To ensure maximum safety for the players and the customers, ensure that

WARNING! where the product is operated has sufficient lighting to allow any warnings to be read. Operation under insufficient lighting can cause bodily contact with each other, hitting accident, and or trouble between customers. Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's flickering or deviation as is. Failure to observe this can have a bad influence upon the players' or the customers' physical conditions. It is suggested to ensure a space allowing the players who feel sick while playing the game to take a rest. Check if all of the adjusters are in contact with the surface. If they are not, the Cabinet can move and cause an accident.

Ensure that all of the Adjusters are in contact with the floor.

Page 10

Do not put any heavy item on this product. Placing any heavy item on the product can cause a falling down accident or parts damage.

WARNING! Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. To avoid electric shock, check to see if door & cover parts are damaged or omitted. To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product. Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.

To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause making bodily contact with each other, hitting accidents, and or trouble

CAUTION! between customers.

PRECAUTIONS TO BE HEEDED DURING OPERATION (PAYING ATTENTION TO CUSTOMERS)

To avoid injury and trouble, be sure to constantly give careful attention to the behavior and manner of the visitors and players.

To avoid injury and accidents, those who fall under the following categories are not allowed to play the game. Those who need assistance such as the use of an apparatus when walking.

WARNING! Those who have high blood pressure or a heart problem. Those who have experienced muscle convulsion or loss of consciousness when playing video game, etc. Those who have a trouble in the neck and or spinal cord. Intoxicated persons. Pregnant women or those who are in the likelihood of pregnancy. s susceptible to motion sickness. ‘sons whose act runs counter to the product's warning displays. A player who has never been adversely affected by light stimulus might experience dizziness or headache depending on his physical condition when playing the game. Especially, small children can be subject to those conditions. Caution guardians of small children to keep watch on their children during play. Instruct those who feel sick during play to have a medical examination. To avoid injury resulting from falling down and electric shock due to spilled drinks, instruct the player not to place heavy items or drinks on the product. To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in the openings of the product or small openings in or around the doors. To avoid falling down and injury resulting from falling down, immediately stop the customer's leaning against or climbing on the product, etc. To avoid electric shock and short circuit, do not allow the customers to unplug the power plug without a justifiable reason.
Page 11

A

CAUTION! Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or falling down, resulting in injury due to fragments and falling down.

Children should be accompanied by their guardians for playing the game.

The steering wheel has reaction mechanism. Caution the guardians

of children so as not to insert hands

or arms in between the spokes. Failure to observe this can cause

injury due to a sudden move of the

steering wheel.

Caution the player so as not to hold a child in his/her lap to play. Failure to observe this may cause injuries resulting from a falling accident.

Instruct those who wear high-heel or thick-sole shoes to refrain from playing the game. Failure to observe this can cause a sprain.

Page 12
  • NAME OF PARTS MAIN BILLBOARD

SUB BILLBOARD

PTV

COIN CHUTE DOOR

CASHBOX DOOR

PTV BASE

ACCELERATOR & BRAKE

MAIN CABINET |

PILLARR FIG. 4a OVERVIEW

AC UNIT = FIG. 4b SIDE VIEW

TABLE 4

Width X Length Xx Height Weight

PTV1,140mm_X__554mmX_1,670 mm110 kg
PTV BASE1,165mmX644mmX_387 mm24kg
MAIN CABINET1,580 mm_X 1,880 mmX 1,410 mm291 kg
MAIN BILLBOARD1,252mmX492mmX330mm16kg
SUB BILLBOARD1,145mmX335mmX260mm9kg
PILLAR R170mmX400mmX 1,503 mm12kg
PILLAR L170mmX400mmX 1,503 mm12kg
When assembled1,580mmX460mmX 2,230 mm|Approx. 479 kg
Page 13
  • ACCESSORIES

When transporting the machine, make sure that the following parts are supplied.

TABLE 5 ACCESSORIES

DESCRIPTIONOWNERS MANUAL,KEY MASTERKEY
Part No. (Qty.)420-6545-01 (1)220-5576 (2)(2)
NoteFor opening/closingFor the CASHBOX DOOR.

. the doors Figures If Part No. has no description, the Number has not been registered or can not be registered. Such a part may not be obtainable even if the customer desires to purchase it Therefore, ensure that the part is in safekeeping with you. The Keys are inside the Coin Chute Door at the time of SERVICE MANUAL NAOMI ENG shipment from the factory. 420-6455-01 (1) INSTRUCTION MANUAL FOR THE GAME BOARD

AC Cable (Power Cord) CORD CLAMP 600-6729 (1) AC 110V AREA 280-5009-01 (1) 600-6695 (1) AC 120V AREA Used for securing the 600-6618 (1) AC 220 ~ 240V AREA power cord. Used for installation, see|5 | of Section 6. s of Section 6.

VOL CONT B-5K OHMSW MICRO TYPELAMP 14V 3.8W.
220-5373509-5636 (1)390-6677-038 (1)

o})

220-5484Spare, refer to Section 11.Spare, refer to Section 15.

Spare, see Section 10, 12.

Page 14

FUSE 6.3A 125V 514-5086-6300 (1) Spare, see Section 17.

CARTON BOX 601-10532 (1) TOSHIBA Remote Controller used for adjustment of the projector. See Section 14. 200-5536(1)

One of the above 2 types of

Remote Controllers is used for the Projector. MITSUBISHI Remote Controller used for adjustment of the projector. See Section 14. 200-5532(1)

The Remote Controller is attached to the Projector at the time of shipment.

Used for transporting the Game Board. Refer to Next Page.

Page 15

HOW TO USE THE CARTON BOX

When requesting for the replacement/repair of this product's Game Board (NAOMI BOARD), follow the instructions below. Transporting the Game Board in an undesignated status is unacceptable. An erroneous handling can cause parts damage. Put the Game Board in the Carton Box together with the Shield Case. Do not

IMPORTANT

unnecessarily disassemble nor remove parts. By paying careful attention to the following Figure and the direction shown by on-Carton-Box printing, put the Shield Case in the Carton Box. When putting the Shield Case in the Carton Box, do not remove Leg Brackets. The projected portions of the packing material is intended for cushioning. Therefore, do not bend the projected portions.

"CHECK SIDE" Display

Projected portions of Wie packing material.

Fold the packing material in the sequential order of the numbers shown in the Figure, enfold the Shield Case and put it in the Carton Box. Positioning the Shield Case upside down or packing in the manner different from what is shown in this Figure can cause the Game Board and other parts to be damaged.

Page 16
  • ASSEMBLING AND INSTALLATION

comply with the instructions can cause electric shock hazard.

WARNING! Perform assembling as per this manual. Since t a complex machine,

erroneous assembling can cause an electric shock, machine damage and or not functioning as per specified performance. When assembling, be sure to use plural persons. Depending on the assembly work, there are some cases in which working by one person alone can cause personal injury or parts damage. Ensure that connectors are accurately connected. Incomplete connections can cause electric shock hazard. Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards. Do not carelessly push the PTV. Pushing the PTV carelessly can cause the PTV to fall down. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause a severe

A Perform assembly work by following the procedure herein stated. Failing to

accident such as electric shock. Failing to comply with this instruction can cause a severe accident such as electric shock to the player during operation. Provide sufficient space so that assembling can be performed. Performing work in places with narrow space or low ceiling may cause an accident and assembly work to be difficult.

load to the fluorescent lamps and plastic parts. Failure to observe this can cause parts damage, resulting in injury due to fragments, cracks and broken pieces. To perform work safely and securely, be sure to prepare a step which is ina secure and stable condition. Performing work without using the step can cause violent falling down accidents. The PTV screen is susceptible to damage. Use care when handling the PTV. If damaged, repair can not be performed.

f) When handling plastic parts, use care. Do not give a shock or apply excessive

CAUTION!
Page 17

When carrying out the assembly work, follow the procedure in the following 7-item sequence:

ASSEMBLING THE PTV

INSTALLING THE MAIN BILLBOARD, PILLAR L, AND PILLARR

INSTALLING THE PTV

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

POWER SUPPLY, AND EARTH CONNECTION

TURNING POWER ON

ASSEMBLY CHECK NI fd J PS] J IST IS

When assembling, make sure that tools such as a Phillips type screwdriver, wrench (for M16 hexagon bolt), socket wrench (M6, M8 hexagon bolt), ratchet handle, and the master key are available.

Phillips type screwdriver

24mm,

WRENCH (for M16 hexagon bolt)

SOCKET WRENCH, (for M6,MB8 hexagon bolt)

RATCHET HANDLE KEY MASTER

Page 18

ASSEMBLING THE PTV

® Secure the 2 Mask Holders to the PTV

ceiling with the 2 Flat Head screws for each. FLAT HEAD SCREW (2 each) M4X 12

@ Secure the Mask to the PTV with a total

of 6 screws. MASK HOLDER

TRUSS SCREW (2) M5 X 25,chrome, flat washer used.

FIG. 6. 1a SCREW (4)black M5 X 20,w/flat & spring washers

® Secure the 2 PTV Holders to the

PTV front with the 2 screws for each.

FIG. 6.1b SCREW(2 each)M5 X 16,w/flat & spring washers

\ \P TV HOLDER

Page 19

2 INSTALLING THE MAIN BILLBOARD, PILLAR L, AND PILLARR

® Take out the 7 truss screws to

remove the BACK PANEL COVER from the back of main cabinet.

@ Take out the 2 hexagon bolts to

remove the BACK PANEL from the back of main cabinet.

® Take out the 2 truss screws, unlock

the lock, and remove the BACK LID.

TRUSS SCREW (7) M4 X 20,chrome, lat washer used.

al BACK PANEL COVER HEXAGON BOI . j ST

M6 X 40,w/sp: flat washer used.

  • \ TRUSS SCREW (2) BACK LID/ M4 X 25,black
Page 20

® Install the PILLAR L and PILLAR R to the left & right sides of main cabinet and secure with the 6 hexagon bolts for each. Fasten the 2 bolts from inside the BACK LID. The PILLAR R has wiring. Check with the connector portion. Install the PILLAR L to the left side and the PILLAR R to the right-hand side of main cabinet when facing from the PTV screen. Fasten the bolts while another person supporting the PILLAR.

\ HEXAGON BOLT (6 each) \ M6 X 40,w/spring washer, flat washer used.

FIG. 6.2 ¢

FIG. 6.2d

Page 21

® To secure the PILLAR, install the L-shaped Bracket from the seat side. Secure the PILLAR CABI BRACKET UPPER with the 3 truss screws and the PILLAR CABI BRACKET LOWER with the 4 truss screws. Perform this on the both sides.

PILLAR CABI BRACKET UPPER

TRUSS SCREW (3 each) | M6 X 30,black /

\ FIG. 6.2¢ 7 \ TRUSS SCREW (4 each) . M6 X 30,black

PILLAR CABI BRACKET LOWER

© Connect the PILLAR R's wire connector to the main cabinet's connector.

Connect the Connector.

PHOTO 6.2a

Page 22

@ Install the BACK PANEL, the BACK PANEL COVER, and the BACK LID to the main cabinet back.

FIG. 6.2 f

® Lift the MAIN BILLBOARD onto the 2 PILLARs by 2 persons. Use care so as not to pinch hands or damage wire.

FIG. 6.2 g

For performing work, use 2 or more workers.

Page 23

TRUSS SCREW (4 in total) MS X 50,black,

(©) By using a total of 4 truss screws from

inside the 2 PILLARs, secure the MAIN BILLBOARD. flat washer used.

FIG. 6.2h

be sure to use a step. a) rai S = bh z= | & FSI by a r] a Ss

Page 24

Secure the END CAP BRACKET to the PILLAR with the 2 screws. Perform this on the both sides.

(©) Connect the wire connector of the MAIN BILLBOARD to the connector of the PILLAR R.

SCREW (2 each) M4 X 20,black,w/flat & spring washers Connect the Connector.

END CAP BRACKET PHOTO 6.2b

By using the 3 truss screws, install the END CAP to the END CAP BRACKET. Perform this on the both sides.

END CAP

PHOTO 6. 2¢

TRUSS SCREW (3 eachM4 X 12,chrome,

fat washer used.

Page 25

PIPE BRACKET

@) By using the 2 screws, install the PIPE

BRACKET to the END CAP BRACKET.

SCREW (2 each) M4 X 20,w/flat &

spring washers

Install the PIPE SAFETY on to the PIPE PIPE SAFETY BRACKET with the 2 truss screws. Perform this on the both sides.

TRUSS SCREW (2 each) M4 X 16,black

PHOTO 6. 2d

  • By using the 4 truss screws, secure the PIPE to the PIPE BRACKET. Perform this on the both sides.

TRUSS SCREW (4) (M4 X 12,chrome

PHOTO 6.2 ¢€

Page 26

INSTALLING THE PTV

®© Fit the PTV BASE and the main cabinet. The surface of @ Secure the PTV BASE and the main cabinet with a total

PTV BASE fitting to the main cabinet is predetermined.

of 6 hexagon bolts.

HEXAGON BOLT «\ MB X 30,w/spring washer, flat washer used.

® Mount the PTV halfway onto the PTV

BASE by 3 or more persons. At this time, be sure to use another person to support the main cabinet or cause the adjusters to come into contact with the floor.

FIG. 6.3b

Page 27

Fasten the 2 s

@ Connect the 2 wire connectors from the main cabinet to

the PTV Connector Panel. The signal connector has the MITSUBISHI securing screws at the both ends. Fasten the 2 screws PROJECTOR tightly after having connected the connector. At this time, use 3 persons to support the PTV.

TOSHIBA PROJECTOR

At this time, use 3 persons to support the PTV.

® Fit the PTV to the main cabinet. Use care so as not to damage wiring at this time. @ secure the joining portion of the PTV and the main cabinet with a total of 4 screws.

FIG. 6.3d

/;

M5 X 40,chrome, flat washer used. rews tightly.

FIG. 6.3¢ Fasten the 2 screws tightly

/ TRUSS SCREW (4 in total)

Page 28

@ Install the SUB BILLBOARD to the PTV ceiling. Insert the SUB BILLBOARD to the 2 Mask Holders on the PTV ceiling and secure with the 2 truss screws. To perform work safely and securely, be sure to use a step. Do not step on the PTV or the main cabinet to perform work.

TRUSS SCREW (2) M5 X 16,chrome, flat washer used. . SUB BILLBOARD

FIG. 6.3

When performing work, be sure to use a step.

Page 29

4 SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Make sure that all of the adjusters are in contact with the floor. If they are not, the cabinet can move and cause an accident.

WARNING!

This product has 8 casters (4 for PTV BASE, 4 for MAIN CABINET) and 8 Adjusters (4 for PTV BASE, 4 for MAIN CABINET). (FIG. 6. 4a) When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level. CASTER

® Transport the product to the

installation position. Be sure to provide adequate space allowing the player to get on and off.

@ Have all of the Adjusters make

contact with the floor. Adjust the Adjuster's height by using a wrench so that the machine position is kept level.

® After making adjustment, fasten

the Adjuster Nut upward and secure the height of Adjuster (FIG. 6. 3 b). ADJUSTER

ADJUSTER

CASTER

q f Approx.Smm

FIG. 6.4¢ Refer to this Fig. (Scale:1/100) FIG. 6.44

for the layout of the place of Be sure to provide space as shown between

installation. the Air Vent and the wall surface.

Page 30

5 POWER SUPPLY, AND EARTH CONNECTION

Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage

WARNING! Breaker can cause a fire when electric leakage occurs. Ensure that the "accurately grounded indoor earth terminal" and the earth wire cable are available (except in the case where a power cord plug with earth is used). This product is equipped with the earth terminal. Connect the earth terminal and the indoor earth terminal with the prepared cable. If the grounding work is not performed appropriately, customers can be subjected to an electric shock, and the product's functioning may not be stable. Ensure that the power cord and earth wire are not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord and wire can cause electric shock and short circuit accidents. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering. After wiring power cord on the floor, be sure to protect the power cord. Exposed power cord is susceptible to damage and causes an electric shock accident.

The AC Unit is mounted on the left side of the machine. The AC Unit has Main SW, Circuit Protector and the Inlet which connects the Power Cord.

® Ensure that the Main SW is OFF.

EARTH TERMINAL MAIN SW \ Connect with the indoor earth terminal, / (0)

Main SW off

@ iC) @ eS ® 2 CIRCUIT PROTECTOR

@ o AC Cable (Power Cord)

° ° =

® © o0000 ¥ w \ : : al ° [| to

FIG. 6.5 a AC unit INLET/

Page 31

@) Connect one end of the earth wire to the AC Unit Connect the Earth Wire

earth terminal, and the other end to the indoor earth to the Earth Terminal. terminal. The AC Unit earth terminal has a Bolt and Nut combination. Take off the Nut, pass the end of earth wire through the Bolt, and fasten the Nut.

Note that the Earth Wire is incorporated in the Power Cord for the Areas of AC 120V (USA) and

AC 220A‘240V, and therefore, this procedure is oy

not necessary. FIG. 6. 5b Earth Wire Connection @ Firmly insert the power plug into the socket outlet. Insert the opposite side of Power Cord plug to the AC Unit's connector ("INLET").

@ Perform wiring for the Power Cord and Earth Wire. Install protective covering for the Power Cord and Earth Wire.

| Wiring Cover

FIG. 6. 5 c Connecting Power Cord and Earth Wire

In case the Power Plug is apt to come out of place, secure the

Power Cord to the periphery of the AC Unit with the Cord Clamp (an accessory).

HOW TO USE THE CORD CLAMP

Page 32

TURNING POWER ON

Turn the AC Unit's main switch on to supply power. When power is turned on, the fluorescent lamp inside the MAIN BILLBOARD lights up. The monitor displays NAOMI SYSTEM boot up and then proceeds to the advertise mode. During this time, the initialization setting is automatically performed. Do not touch the machine until the advertise mode is displayed on the monitor after finishing the initialization setting. While initializing, the steering wheel turns left & right and stops at the centering position. In the initialization setting, the values of V.R. inside the control panel are corrected. Until the initialization is finished (the steering wheel stops automatically), do not touch the steering wheel or play the game. If you do, the steering wheel reaction during the game (reaction at the time of a course-out or crashing) can not be obtained correctly. In case of an abnormal reaction during the game, turn the power on again from the beginning and complete the initialization setting. In this product, once the power is turned off, the data of inserted coins less than one credit and BONUS ADDER is cleared. In the advertise mode, sound is emitted from the 2 speakers. Sound is not emitted if set to NO SOUND OUTPUT in the test mode.

Image output on the monitor.

Fluorescent lamps are lit,

Page 33

7 ASSEMBLING CHECK

In the TEST MODE, ascertain that the assembly has been made correctly and IC BD. is satisfactory (refer to Section 9). In the test mode, perform the following test:

  • MEMORY TEST

Selecting the desired RAM TEST item on the MEMORY TEST MODE test mode menu screen causes the on-board memory to be tested automatically. The game RAM TEST board is satisfactory if the display beside each IC No. shows GOOD. 1C29 GOOD 1C34 GOOD IC16 GOOD IC18 GOOD 1C20 GOOD 1C22 GOOD IC9 GOOD IC10 GOOD IC11 GOOD IC12 GOOD

PRESS TEST BUTTON TO CONTINUE

  • C.R.T. TEST

C.R.T.TEST PAGE 1/2 In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the monitor is tested) to be displayed. Although the monitor RED adjustments have been made at the time of shipment from the factory, color deviation, etc.,

GREEN may occur due to the effect caused by

BLUE geomagnetism, the location building's steel frames and other game machines in the

WHITE periphery. By watching the test mode screen,

make judgment as to whether an adjustment is needed. If it is necessary, adjust the monitor by

referring to Section 14.

PRESS TEST BUTTON TO CONTINUE

C.R.T. TEST PAGE 2/2

PRESS TEST BUTTON TO EXIT

Page 34
  • INPUT TEST

INPUT TEST

COIN CHUTE #1

COIN CHUTE #2

VIEW HORN SHIFT (L] SHIFT (H] SHIFT [R] HANDLE. ACCEL BRAKE OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF XXH XXH XXH

PRESS TEST + SERVICE BUTTON TO EXIT

(4)OUTPUT TEST

OUTPUT TEST

START LAMP. VIEW LAMP HORN LAMP ROLL LEFT ROLL RIGHT

->EXIT OFF OFF OFF OFF OFF

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

(5)SOUND TEST

SOUND TEST

B.G.M EFFECT {dd ICS —__d -> EXIT O/ XX O/ XX

0/ XX

SELECT WITH SERVICE BU1 AND PRESS TEST BUTTON Selecting the INPUT TEST on the test mode menu screen causes the screen (on which each switch is tested) to be displayed. Press each switch. For the coin switch test, insert a coin from the coin inlet with the coin chute door open. If the display beside each switch indicates "ON," the switch and wiring connections are satisfactory.

Select OUTPUT TEST from the menu in the test mode to cause the screen (on which each lamp and wiring connections are tested) to appear. Ensure that lamp light up satisfactorily.

In the TEST mode, selecting SOUND TEST causes the screen (on which sound related BD and wiring connections are tested) to be displayed. Check if the sound is satisfactorily emitted from each speaker and the sound volume is appropriate.

Perform the above inspections also at the time of monthly inspection.

Page 35
  • PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

AY When moving the machine, be sure to unplug the power plug. Moving the

machine with the plug as is inserted can damage the power cord and cause fire

WARNING! and electric shock hazards. When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords and earth wires. Damaging the power cords can cause electric shock and short circuit hazards. When lifting the cabinet, be sure to hold the grip portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions due to the empty weight of the cabinet, and cause personal injury. When transporting the product in places with step-like differences in grade, disassemble into each unit before transporting. Lifting up the product in an attempt to cross the step-like differences in an as is assembled condition may

damage the unit's joining portions and cause a personal injury resulting from

damage. When moving the PTV, do not push it from the rear side. Push it from sideways. Pushing the PTV from the rear side can have the PTV fall down, causing personal injury etc. In case the floor has slanted surfaces or step-like differences, be sure to move the machine by 2 or more persons. Do not insert the fork to places other than designated when using a Forklift to transport the machine. Failure to observe this could cause falling down and injury resulting from falling down.

Do not push the plastic made parts. Failure to observe this may damage parts and cause injury due to fragments resulting from damage.

CAUTION!

@ When transporting the product in places with steps, disassemble into each unit before transporting. Inclining the product in an as is assembled condition or

IMPORTANT placing the cabinet in places with steps can damage the unit's joining portions. @ To protect surface, do not directly apply a rope to the surfaces of product. Use protective materials to the places the rope is applied to.

Do not push PTV from the back. Pushing the PTV from the back can cause the PTV to fall down. Push it from the side.

Page 36

FIG.7a

When transporting the product in places with steps or step-like differences in grade, disassemble into each unit before transporting.

FIG. 7b

Page 37
  • CONTENTS OF GAME

The following explanations apply to the case the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of faults may have occurred. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation.

When the product is energized, the Billboard's fluorescent lamp is always lit. During the advertise mode, the advertise screen is shown on the monitor and sound is emitted from the speakers. Setting to No Sound Output during the advertise is possible in the TEST mode.

Image output on the monitor.

Fluorescent lamps are lit.

Page 38

OUTLINE OF THE GAME

  • This is a single, driving game in which the player competes with rivals by driving a Trailer Truck to cross America.

+ When coins are inserted to gain credits, the START button starts flashing. Press the START button to proceed to the SELECTOR mode where you can select your truck and trailer. The game starts upon selecting the truck and the trailer.

+ Based on the setting made in the test mode, the number of coins inserted to obtain a credit counts as one credit in this product. The number of credits necessary to start game and to continue game can be set in the test mode.

  • The game consists of the 4 kinds of stages and 3 kinds of parking stages (Bonus stages). + When continued, game is played at the beginning of the latest stage where you result in game over.

+ Ifyour score falls within the top 5, you can enter your name.

CONTENTS OF GAME

  • Pass the checking point within a certain period of time and reach the goal, and you can clear the stage.
  • The game finishes when clearing all 4 stages.

+ Ifyou can reach the goal ahead of your rival trailers in each stage(the Ist through the 3rd), you can play Parking game (Bonus game).

GAME OVER

+ Ifyou fail to pass the checking point within a certain period of time or fail to goal, game is over.

  • Getting behind the rival trailers at the checking point or failing on the Parking game does not result in game over.
Page 39

HORN AT THE ASSISTANT DRIVER'S SEAT STEERING WHEEL OPERATIO. START BUTTON VIEW CHANGE BUTTON

CONTROL PANEL and ACCEL. & BRAKE HORN AT THE DRIVER'S SEAT

<STEERING WHEEL> SELECTOR _ : Turnright or left to select an object. GAME PLAY : Operate the Trailer Truck. <HORN AT THE DRIVER'S SEAT> SELECTOR — : Decide GAME PLAY : Blow the horn to signal the car ahead to move out of the way or to have it increase the speed. Have the trailer ahead increase the speed. <ACCEL..> SELECTOR — : Decide GAME PLAY : Increase your Trailer Truck speed. <BRAKE> SELECTOR _ : Void GAME PLAY : Decrease your Trailer Truck speed, or stop it. <GEAR> SELECTOR — : Void

GAME PLAY : 3-position, HI (High), LOW, R (Reverse)

<VIEW CHANGE> SELECTOR — : Void GAME PLAY : Select either Driver's View or Bird View. <START BUTTON> The START button flashes when the number of coins that are worth one credit are inserted. While flashing, press the START button to proceed to the SELECTOR. It also flashes when one or more credit(s) remains after the game over. <HORN AT THE ASSISTANT DRIVER'S SEAT> SELECTOR — : Decide GAME PLAY $: Signal the car ahead to move the way or to increase the speed. Signal the trailer ahead to increase the speed. This has the same effect with the hom at the driver's seat.

Page 40

SELECTOR

HB rruck SELECT

Select the truck from among ASPHALT COWBOY, STREAMLINE, HIGHWAY CAT, LONG HORN, and NIHONMARU (not available for Korea version). Each truck's abilities in SPEED, TORQUE, and TOUGHNESS differ.

HB TRAILER SELECT

When starting in the stages 2, 3, and 4, select the trailer for towing from the 2 trailers. The weight, the length, and the transportation fee differ. The heavier the trailer, the more the difficulty.

DIFFICULTY

NORMAL

TRAM ORET EWA $ 12600

Page 41

NAME ENTRY

If your score falls within the top 5, you can enter your name.

es EOIN WOM recore

VIEWING THE GAME SCREEN

~ J MIRROR

TRANSPORTAION

GEAR CHANGE INDICATOR

GEAR CONDITION

TACHOMETER

Page 42

<DESTINATION> Name of the destination point.

<TIME LIMIT> Indicates the player's playable time. Additional time will be added when passing the CHECKPOINT and obtaining TIME BONUS.

<REARVIEW MIRROR> Indicates the rear condition while DRIVER'S VEIW is being selected.

<TRANSPORTATION FEE> Indicates the fee you receive when you reach the destination. If you give damage to the trailer by hitting another car, etc., the fee will be reduced.

<TACHOMETER> Indicates speed of rotation.

<GEAR CHANGE INDICATOR> Indicates the gear condition (4 positions in total) with the lamp on the monitor.

<GEAR CONDITION> Indicates the current gear condition. The three types of gears (REVERSE * LOW * HI) are available.

Page 43
  • EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

NAOMI GAME BOARD is used for the product. The system of this game board allows

another game to be played by replacing the ROM Board Case mounted on the NAOMI CASE. As such, the Test Mode of this system consists of the System Test Mode for the system to execute SELF-TEST, COIN ASSIGNMENTS, etc. used in common for the machines employing the NAOMI BOARD, and the Game Test Mode for the specific product to execute Input/Output test for the operation equipment, difficulty setting, etc. In this manual, explanations regarding the System Test Mode cover the settings for this product only. For the details of the System Test Mode, refer to NAOMI SERVICE MANUAL, an accessory.

TABLE 9 EXPLANATION OF TEST MODE

REFERENCE

ITEMS DESCRIPTION SECTIONS

INSTALLATION | When the machine is installed, perform the following: See ye

OF MACHINE 1. Check to ensure each is the standard setting at shipment. MANUAL

  • Check each Input equipment in the INPUT TEST mode. 93E . i 9
  • Check each Output equipment in the OUTPUT TEST mode. 3-38.
  • Test on-IC-Board IC's in the SELF-TEST mode. 230
MEMORYThis test is automatically executed by selecting RAM TEST, oria St =

ROM BOARD TEST in the Menu mode. MANUAL

PERIODICPeriodically perform the following:SERVIC
SERVICING1. MEMORY TESTMANUAL
  • Ascertain each setting.
  • To test each Input equipment in the INPUT TEST mode.
  • To test each Output equipment in the OUTPUT TEST mode.
CONTROL1. To check each Input equipment in the INPUT TEST mode.seeie
SYSTEM2. Adjust or replace each Input equipment.MANITAL
  • If the problem still remains unsolved, check each equipment's 248 mechanism movements. aaa 9-3C
MONITORIn the Monitor Adjustment mode, check to see if Monitor (Projec-SERVIC

tor) adjustments are appropriate. MANUAL 9-3B.F 10,11,12

IC BOARD 1. MEMORY TEST SRE

2. In the SOUND TEST mode, check the sound related ROMs. MANDAL

DATA CHECKCheck such data as game play time and histogram to adjust theSEE VIE

difficulty level, ete. piece 9-3D SERVICE MANUAL. 9-3G

Page 44

9-1 SWITCH UNIT AND COIN METER

Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit accidents.

Adjust to the optimum sound volume by considering the environmental requirements of the installation location. If the COIN METER and the game board are electrically disconnected, game play is not possible.

IMPORTANT

SPEAKER VOLUME For SUPER WOOFER \ \ TEST BUTTON SPEAKER VOLUMEFor SPEAKERS \ at theCONTROL PANEL left & right. _—_o SERVICE BUTTON jee > ~

SWITCH UNIT i)

Open the coin chute door, and the NS /) switch unit shown will appear. The — function of each SW is as follows: ‘SUPER

‘SPEAKER WOOFER TEST SERVICE

FIG. 9. 1 a SWITCH UNIT

SPEAKER VOLUME: _ Sound volume can be adjusted for the CONTROL PANEL left & right SPEAKER speakers.

SPEAKER VOLUME: _ Sound volume can be adjusted for the SUPER WOOFER and the SUPER WOOFER BASE SHAKER under the seat.

TEST BUTTON: Enters to the test mode. TEST

SERVICE BUTTON: _ Gives credits without registering on the coin meter. SERVICE

COIN METER ( )

Open the Cashbox Door by using the key to CON ETERS @

have the Coin Meter appear underneath the Cashbox.

FIG. 9. 1b COIN METER

Page 45

9-2 SYSTEM TEST MODE

IMPORTANT The contents of settings changed in the TEST mode are stored when the test mode is finished from EXIT in the menu mode. If the power is turned off before the TEST mode is finished, the contents of setting change become ineffective. Executing "BACKUP DATA CLEAR" in the SYSTEM TEST MODE does not clear the BOOKKEEPING data in the GAME TEST mode.

Entering the TEST mode clears fractional number of coins less than one credit

and BONUS ADDER data. Perform setting as per specified in this manual for operation. If setting not specified is performed for operation, proper function of this product may not be obtained.

In the SYSTEM TEST MODE, IC BD functioning can be checked, the monitor adjusted, and the coin setting performed. Refer to NAOMI SERIVCE MANUAL for the details. Note that the setting of the following items need to be performed in accordance with the instruction given.

CABINET TYPE : 1 PLAYER(S) MONITOR TYPE HORIZONTAL SERVICE TYPE COMMON COIN CHUTE TYPE : COMMON

Page 46

9-3 GAME TEST MODE

A. GAME TEST MODE MENU (MAIN MENU)

SYSTEM MENU JAPAN VERSION

RAM TEST JVS TEST

SYSTEM ASSIGNMENTS COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING ROM BOARD TEST -> GAME TEST MODE [XXXXX XX XXXX--- ==] EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

SYSTEM TEST MODE MENU 18WHEELER TEST MENU

SOUND TEST GAME ASSIGNMENTS VOLUME SETTING BOOKKEEPING BACKUP DATA CLEAR -> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

GAME TEST MODE MENU

FIG. 9. 3a MENU MODE

+ Press the TEST button to indicate the SYSTEM TEST MODE MENU screen.

+ Bring the arrow by pressing the SERVICE button and select the GAME TEST MODE. Press the TEST button to indicate the GAME TEST MODE MENU screen.

+ By pressing the SERVICE button, bring the arrow and select an item. Press the TEST button to enter the test item.

  • Select EXIT and press the TEST button to finish the GAME TEST MODE. The screen returns to the SYSTEM TEST MODE MENU screen. Select EXIT in this mode and press

the TEST button to finish the SYSTEM TEST MODE. The screen returns to the game mode.

4l

Page 47

B. INPUT TEST

When the INPUT TEST is selected, the following screen is displayed on the monitor.

INPUT TEST

COIN CHUTE #1 OFF COIN CHUTE #2 OFF SERVICE OFF TEST OFF START OFF VIEW OFF HORN OFF SHIFT [L] OFF SHIFT [H] OFF SHIFT [R] OFF HANDLE XXH ACCEL XXH BRAKE XXH

PRESS TEST + SERVICE BUTTON TO EXIT

+ When pressing each switch, if the display next to the item changes to ON from OFF, the switch and the wiring connection are satisfactory.

  • To check COIN CHUTE #1 & #2, open the COIN CHUTE DOOR and insert coins.

+ "HORN" is for the driver seat and the assistant driver seat. Because the same circuit is used for HORN in the driver and the assistant driver seats, if the switch and the wiring connection are satisfactory, pressing the HORN at either side changes the display to ON from OFF.

+ For the steering wheel, the accelerator, and the brake, operate each input device and check to see if the value changes in accordance with operation. Items to be checked: Each switch (COIN/ SERVICE/ TEST/ START/ VIEW CHANGE/ HORN/ SHIFT <H L R>) Each volume (STEERING WHEEL/ ACCELERATOR/ BRAKE)

+ Press the SERVICE and TEST buttons simultaneously to return to the MENU screen.

Page 48

C. OUTPUT TEST

Selecting the OUTPUT TEST displays the following screen on the monitor. The condition of each lamp and motor can be checked.

OUTPUT TEST

START LAMP OFF VIEW LAMP OFF HORN LAMP OFF ROLL LEFT OFF ROLL RIGHT OFF

->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

+ Bring the arrow to the desired item and press the TEST button. The display next to the item changes to ON from OFF, the lamp lights up, and the motor functions. @ LAMP item — : Ifthe lamp lights up, operation is satisfactory. @ ROLLLEFT _ : Ifthe motor moves so as to turn the steering wheel counterclockwise, operation is satisfactory.

@ ROLL RIGHT : Ifthe motor moves so as to turn the steering wheel clockwise,

operation is satisfactory.

+ Bring the arrow to EXIT and press the TEST button to return to the MENU screen.

Page 49

D. SOUND TEST

Selecting the SOUND TEST displays the following screen on the monitor. In this mode, sounds used in the game can be checked.

SOUND TEST

B.GM o/XX EFFECT o/XX {id Ics O/XX

-> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Move the arrow by pressing the SERVICE button and select an item. Every time the TEST button is pressed, different sound is played. @ BG.M. : Sound used in the game can be played. @ EFFECT : Sound effects used in the game can be played. e Ics : Sound effects in a loop used in the game can be played.

Bring the arrow to EXIT and press the TEST button to return to the MENU screen.

Page 50

E. GAME ASSIGNMENTS,

Selecting the GAME ASSIGNMENTS displays the following screen on the monitor. Setting for the game can be performed. The contents of setting changes will be effective when the TEST MODE is finished properly. If the setting changes are made, be sure to exit from the TEST MODE.

MOTOR POWER

-> EXIT

SELECT WIT. GAME ASSIGNMENTS

IME [VERY EASY]

DEFAULT SETTING

EERVICE BUTTON AND PRESS TEST BUTTON [VERY EASY]

[LIGHT]

@ START TIME

@ CHECK POINT TIME

@ MOTOR POWER

@ DEFAULT SETTING

: Time limit given to the player at the beginning of the stage can

be set. Select from among VERY EASY, EASY, NORMAL, HARD, and VERY HARD.

: The additional time given to the player when passing the CHECK POINT can be set.

: The feedback stiffness of the steering wheel can be selected from among LIGHT, NORMAL, and HEAVY.

: This makes each setting return to its default setting.

Bring the arrow to EXIT and press the TEST button to return to the MENU screen.

Page 51

F. VOLUME SETTING

Selecting the VOLUME SETTING displays the following screen on the monitor. The volume detecting the steering wheel operation can manually be set. The value can be stored when exiting from the item.

VOLUME SETTING

HANDLE SETTING SET CENTER [LOCK] 00H

-> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

SETTING THE STEERING WHEEL VOLUME

® Press the SERVICE button to bring the arrow to SET CENTER. @) "SET CENTER [LOCK}" display changes to "SET CENTER [SET]." ® Bring the steering wheel to the centering position manually. @ Press the TEST button. The Volume value obtained at this time is stored as the steering wheel's centering value, and "SET CENTER [LOCK]" is displayed. If the value does not fall within 80+/5H at this time, perform volume adjustment by referring to 10-2.

Bring the arrow to EXIT and press the TEST button to return to the MENU screen.

Page 52

G. BOOKKEEPING

Selecting the BOOKKEEPING displays the data of operating status in 2 pages. Press the TEST button to proceed to the next screen. When the TEST button is pressed in the 2/2 PAGE, the screen returns to the MENU mode.

BOOKKEEPING 1/2

NUMBER OF GAMES 0 NUMBER OF CONTINUE 0 AVERAGE PLAY TIME 0OMO0S

PRESS TEST BUTTON TO CONTINUE

PAGE 1/2 displays the data of operating status.

@ NUMBER OF GAMES : Total number of plays. @ NUMBER OF CONTINUE : Total number of continue.

@ AVERAGE PLAY TIME

BOOKKEEPING 2/2

TIME HISTOGRAM OOMOOS - 00M29S ------- 00M30S - OOM59S 01MOOS - 01M29S 01M30S - 01M59S 02MOOS - 02M29S 02M30S - 02M59S 03MOOS - 03M29S 03M30S - 03M59S 04MOOS - 04M29S 04M30S - 04M59S O5MOOS - 05M29S 05M30S - 0OSM59S 06MOOS - 06M29S 06M30S - 06M59S OVER 07MO00S ecooocoooooooooooe

PRESS TEST BUTTON TO EXIT

PAGE 2/2 displays Histogram of Number of Play as against Play Time.

Page 53

H. BACKUP DATA CLEAR

Selecting the BACKUP DATA CLEAR displays the following screen on the monitor.

The contents of BOOKKEEPING in the GAME TEST MODE and the ranking data can be

cleared. Note that this operation does not affect the contents of GAME ASSIGNMENTS and the VOLUME SETTING. The COIN/CREDIT related data can be cleared in the BACKUP DATA CLEAR in the SYSTEM TEST MODE.

BACKUP DATA CLEAR

YES (CLEAR) ->NO (CANCEL)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

+ When clearing, bring the arrow to "YES (CLEAR)" and press the TEST button. "YES (CLEAR) COMPLETED" is displayed, "COMPLETED" is flashing, and the data is cleared. When the data has been cleared, the display stops flashing. After the data has been cleared, bring the arrow to "NO (CANCEL)" and press the TEST button to return to the MENU screen.

+ Bring the arrow to "NO (CANCEL)" and press the TEST button to return to the MENU screen without clearing the data.

Page 54

10. CONTROL PANEL (HANDLE MECHA)

aN

WARNING!

A

CAUTION!

IMPORTANT

Before starting to work, ensure that the Power SW is OFF. Failure to observe this can cause electric shock or short circuit. Use care so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard. Do not insert hand into the mechanism so as not to cause hand and fingers

pinched in. Failure to observe this can cause a serious injury such as a

fracture. When performing work such as parts replacement other than those specified in this manual, be sure to contact where you purchased the product from and confirm the work procedures and obtain precautions prior to performing work. Inappropriate parts replacement and/or installing with erroneous adjustment can cause an overload or the parts to come into contact, resulting in an electric shock, a short circuit, and a fire. Use care when removing the HANDLE MECHA so as not to hurt the back.

shock, a short circuit, and a fire Dropping the HANDLE MECHA on your foot can cause a fracture. Be very careful of this point

careful of this point.

When putting the HANDLE MECHA, do not make the gear or the sensor portion face down. Failure to observe this may damage the parts due to its own weight.

Be sure to perform Volume value setting in the Volume Setting in the Test Mode after replacing or adjusting the Volume.

10- 1 REMOVING THE HANDLE MECHA

In cases the Steering operability is poor and the adjustment of VOLUME SETTING in the TEST mode is ineffective, the causes may be the Volume Gear's mesh failure and or Volume malfunctioning. By using the following procedure, adjust Volume gear mesh, or replace the Volume. In this product, when the Steering Wheel is moved fully left/right, if the Volume shaft is rotating within the movable range, the Volume is not feared to be damaged. Secure the Volume in the manner the Volume shaft is oriented as shown and the gears are appropriately engaged when the steering wheel is in the centering position allowing the car to go straight forward. In order to perform V.R. adjustment or replacement, remove the HANDLE MECHA as per the following procedure.

© Turn power off.

Page 55

@) Take out the 4 truss screws at the center of the steering wheel to remove the FRAME HORN

BUTTON and the CAP HORN BUTTON. A small part (PIN HORN BUTTON) is attached to @) Pull out the ROD HORN BUTTON @) Remove the SPRING and the CUSHION L ® Take out the hexagon nut © Remove the WASHER HANDLE SHAFT @ Pull the STEERING HANDLE out of the HANDLE SHAFT. The HANDLE and the SHAFT

the CAP HORN BUTTON. Be sure to keep it. @) Pull out the ROD HORN BUTTON. @) Remove the SPRING and the CUSHION L. ® Take out the hexagon nut. © Remove the WASHER HANDLE SHAFT.

are nesting of gear-shape splines hole and the shaft. Be sure to pull the STEERING HANDLE vertically so as not to damage the shaft.

Remove the COLOR HANDLE SHAFT.

TRUSS SCREW (4) FRAME HORN BUTTON M4 X 25,chrome

PIN HORN BUTTON

SPRING &

CUSHION L SS CAP HORN BUTTON

ROD HORN BUTTON CUSHION U

WASHER HANDLE SHAFT

STEERING HANDLE HEXAGON NUT (1) M16

COLOR STEERING HUB

COLOR HANDLE SHAFT

FIG. 10.1 a

Page 56

©) Take out the 4 screws, disconnect a connector, and remove the HORN BUTTON at the assistant driver's seat. (See sec. 15)

Take out the 11 screws to remove the CONTROL PANEL COVER. Wiring connection is inside the CONTROL PANEL COVER. Use care so as not to damage wiring. The CONTROL PANEL COVER is made of plastic. Erroneous handling may damage the part.

@ Disconnect the 2 connectors inside the CONTROL PANEL COVER, and remove the

CONTROL PANEL COVER.

HORN BUTTON TRUSS SCREW (11) M4 X 16,black, flat washer used.

®) Disconnect the HANDLE ® Take out a screw to remove the

MECHA's 2 wire connectors.

earth wire.

Disconnect the connector.

PHOTO 10. 1b

SCREW (1)M4 X 12,w/flat & spring washers

FIG. 10.1b

Page 57

@ Take out the 4 screws to remove the LID TOP FRONT.

® Disconnect the 2 wire connectors of the motor inside the LID TOP FRONT.

TRUSS SCREW (4) M4 X 30,black

LID TOP FRONT

Disconnect the connector.

PHOTO 10. 1c

Page 58

@ Take out a total of 6 screws and the 2 hexagon bolts which secure the HANDLE MECHA.

HOXAGON BOLT (2) M6 X 25,w/spring washer, flat washer used.

SCREW (6 in total) M5 X 16,w/flat & spring washers

PHOTO 10.14

Page 59

Remove the HANDLE MECHA. Use care when performing work.

PHOTO 10. le

() When putting the HANDLE MECHA, be sure to have the gear and the sensor portions face upper. Failure to observe this may damage the parts due to its own weight.

FIG. 10.1 ¢

Page 60

10 - 2 VOLUME ADJUSTMENT/REPLACEMENT

Volume adjustment/replacement should be performed after the HANDLE MECHA has been removed as per 10-1.

ADJUSTMENT

® In order to turn the HANDLE SHAFT, insert the STEERING HANDLE to the HANDLE

SHAFT.

Oo) Secure the HANDLE at the centering position.

  • Loosen the 2 screws which secure the VOLUME BRACKET to push the gear out of mesh.

@ With the HANDLE SHAFT being at the centering position, bring the gear into mesh so that the status of the volume's shaft is as shown in the Fig.

  • Fasten the screws securing the VOLUME BRACKET.
  • After work is finished, perform volume setting in the Test mode.

SCREW (2) M4 X 14w/flat & "D"CUT FACE(HANDLE SHAFT) | spring washers

"D"CUT FACE(VOLUME),

FIG. 10.2a

Page 61

REPLACEMENT

® Disconnect the volume's wire connector.

® Disconnect the volume's wire connector @ Take out the 2 screws which secure the VOLUME BRACKET to remove the BRACKET

together with the volume.

® Take out the 2 screws, remove the VOLUME GEAR, and replace the VOLUME. @ With the HANDLE SHAFT being at the centering position, bring the gear into mesh so that the status of the volume's shaft is as shown in the Fig.

  • Fasten the screws securing the VOLUME BRACKET. © After work is finished, perform volume setting in the Test mode.

VOLUME 220-5473,220-5484

FIG. 10.2b

Page 62
  • SHIFT LEVER

A Before starting to work, ensure that the Power SW is OFF. Failure to observe

this can cause electric shock or short circuit.

WARNING! Use care so as not to damage wirings. Damaged wiring can cause electric

shock or short circuit.

If the Shift Lever operation is not satisfactory, remove the Shift Lever in the following procedure and replace the microswitch.

11 - 1 REMOVING THE SHIFT LEVER

® By following "10-1 REMOVING THE HANDLE MECHA", turn power off, remove the

STEERING HANDLE, and remove the CONTROL PANEL COVER.

  • Take out the 4 Hexagon Bolts.

M8 X 20,w/spring washer

® Remove the SHIFT LEVER. The SHIFT

LEVER has wiring connector. Pull up PHOTO 11. La the SHIFT LEVER slowly until the 2 connectors can be seen.

@)) Disconnect the 2 connectors.

Disconnect the connector.

PHOTO 11.1b

Page 63

11-2 SWITCH REPLACEMENT

Each Microswitch is secured with 2 screws. Remove the 2 screws and replace the Microswitch.

MICROSWITCH 509-5636 PHOTO 11.2

SCREW (2)M2.3 X 12, w/tlat & spring washers\

FIG. 11.2

After replacing the Switch, check to see if the switch is inputted as per Shift Lever operation in the Test Mode.

Page 64
  • ACCELERATOR & BRAKE
WARNING!

IMPORTANT

Before starting to work, ensure that the Power SW is OFF. Failure to observe this can cause electric shock or short circuit. Use care so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. This work should be performed by the Location's Maintenance Man or Serviceman. Performing work by non-technical personnel can cause electric shock hazard. When performing work such as parts replacement other than those specified in this manual, be sure to contact where you purchased the product from. Confirm the work procedures and obtain precautions from where you purchased the product prior to performing work. Inappropriate parts replacement and/or installation with erroneous adjustment can cause an overload or the parts to come into contact, resulting in an electric shock, a short circuit, and a fire.

After having performed adjustment or replacement of the volume, be sure to check the variation of the volume value in the INPUT TEST in the test mode.

If Accel. and Brake operation is not satisfactory, adjustment of volume installation position or volume replacement is needed. Also, be sure to apply greasing to the gear mesh portion once every 3 months.

12 - 1 REMOVING THE ACCELERATOR AND THE BRAKE

Remove the accelerator and the brake to perform maintenance. To remove the accelerator and the brake, a socket wrench for M6 Hexagon bolts and an extension tool are necessary. The wiring connector is inside the accelerator and the brake. When removing, use care so as not to damage wiring.

® Turn power off.

® Turn power off @ Apply the extension tool to

the socket wrench. Remove the 4 Hexagon bolts which secure the accelerator and the brake.

(6) The 2 wire connectors are

connected to the accelerator and the brake. Disconnect the connectors, and the accelerator and the brake can be removed. Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated portions. PHOTO 12.1

HEXAGON BOLT (4) M6 X 25,black,w/spring washer

Page 65

12 -2 ADJUSTING OR REPLACING THE VOLUME

The appropriate value for both ACCEL. Volume and Brake Volume is under 30H when released and over COH when stepped on. Check Volume values in the TEST mode. Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated places. Touching places not specified can cause electric shock or short circuit.

ADJUSTMENT

_ TRUSS SCREW(2) ee t

@ Take out the 2 truss screws and remove the

Front Cover from the Accel. & Brake Unit (FIG. 12. 2 a).

FIG. 12.24

@ Loosen the screw which secure the Potentiobase, and adjust the Volume value by moving the Base. (FIG. 12. 2 b) @® Secure the Potentiobase. @) In the INPUT TEST screen, check to see if the volume value varies in accordance with operation of the pedal.

SCREW MS X 12,w/flat &

220-5484 FIG. 12.2b 220-5373

Page 66

REPLACEMENT TRUSS SCREW(2) M4Xx8 ® Turn the power off. ‘

® Turn the power off @) Take out the 2 screws and remove 4) POTENTIOCOVER ® Disconnect the connector of the

the Potentiocover (FIG. 12. 2 c).

volume to be replaced.

@) Remove the screw which secures ® Remove the Potentiobase together

the Potentiobase (FIG. 12. 2 b).

with the volume as is attached. (FIG. 12. 2c)

© Remove the base and the gear to

replace the volume.

@ After replacing, check to see if the

volume values varies in accordance with operation of the pedal. PO TENTIOBASE._\

FIG. 12.2¢

12 - 3 GREASING

Be sure to use the designated grease. Using undesignated grease can cause parts damage.

IMPORTANT

Once every 3 months, apply greasing to the Spring and gear mesh portion. For spray greasing, use GREASE MATE (PART No. 090-0066). GREASING

FIG. 12.3

Page 67
  • COIN SELECTOR

HANDLING THE COIN JAM

that the selector correctly functions.

CLEANING THE COIN SELECTOR

@ Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Never apply machine oil, etc. to the

IMPORTANT

Coin Selector. After cleaning the Coin Selector, insert a regular coin in the normal working status and ensure that the Selector correctly functions.

The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: Turn the power for the machine OFF. Open the coin chute door.

Open the gate and dust off by using a soft brush ® Remove and clean smears by using a soft cloth

(made of wool, etc.).

dipped in water or diluted chemical detergent and then squeezed dry. Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the rotary shaft. Remove stain from the rotary shaft and shaft receiving portions by wiping off with a soft cloth, etc. After wiping off as per 4D above, further apply a dry cloth, etc. to cause the coin selector to dry completely.

COIN INSERTION TEST

Once every month, when performing the Coin SW Test, simultaneously check the following: Does the Coin Meter count satisfactorily?

[7 Does the coin drop into the Cashbox

correctly? [IIs the coin rejected when inserted while keeping the Reject Button pressed down? If the coin is not rejected when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see

a Ni e CRADLE

FIG. 13b

Insert a coin while keeping the Reject Button pressed down and check if it is rejected.

COIN METER

Page 68

OPTIONAL DOLLAR BILL ACCEPTOR

@ THE COIN DOOR ASSEMBLY USED ON 18 Wheeler Deluxe COMES EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECTIONS ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR THIS APPLICATION.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATOR(S):

FORWARD-MOST Mars 2000 series HOLE POSITION

**42-1155-00 MARS VALIDATOR $1, 2,5 300 CAP

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the cut-out plate. This one entry door can be ordered through Happ Controls or one of Happ Controls authorized distributors. The part number is 40-6000-10EX. The Mars stacker can be obtained through an autherized Mars distibutor.

Note: Your game may have either Happ Controls Coin Door Assembly or the Wells Gardner Coin Door Assembly (not shown).

**Happ part number

Security Locking Bar/Bracket Set Part No.# 999-0966

Modified Cash Box (For use when DBA installed) Part No. # 999-1106

Plastic Cash Box - Full Size Part No. # 999-1177

Page 69

+9 U0D'AI1AAISNAS MMM 0€99-9€€-008-L 66909 T‘O9VOIHD RVOTIN'N LOZ NOILVYOdYOD SIINOYLIITS YANGYV9-STTIM WOI'939M MMM NO-dvNs ‘333° NN d¥NS UVB

YOLVGNVA THE HLIM S3IMLNA 2 YOOC ININ Y3GNN/YIA0 FYNSOTONA Tldads 8 LO-OLL2-S LGM 400d WOLLO

Page 70

Tom Happ Ph: 847-593-6161 ext. 107 tom.happ@happcontrols.com Fx: 847-956-2091 Happ Controls, 106 Garlisch Drive, Elk Grove, IL 60007 Visit our website http://www.happcontrols.com 42-0641-00 iL 42-0405-00 FOR §.25 COIN 42-0405-05 FOR $1.00 COIN ei 42-1044-00 $1.00 4 x .25 1 PLAY 91-1319-00 42-0288-00 ((¢— = 42-0695-05 $1.00 PUSH TO REJECT

yer 42-0351-00 2-0047-00 42-7201-00

43-02-00 \ 43-1003-00. 42-0232-00

42-7355-00 - Q 48-1000-00 42-0119-00

$0.25 42-3079-00 $1.00 42-3113-00 42-7087-00 ; £2.0841-00 43-0196-00—ew camera h ZZ) 42-8177-00 42-8176-00 @a— 41-0021-00 42-8178-00

  • 49-8174-10 Guardian Hasp 30-2400-200
Page 71
  • PROJECTOR

i jector has been adjusted at the time of shipment, avoid making stments without good reason.

CAUTION!

The Projector is subject to color deviation due to Convergence deviation caused by the geomagnetism at the installation location and peripheral magnetic field. After the installation of machine, and before commencing operation, check for Convergence deviation and if deviated, make adjustments.

IMPORTANT

Projector adjustments are stored. Due to distortion or color deviation in the TEST mode, if an adjustment is necessary, use the Remote Control to make adjustments. There are two Projector Makers (Toshiba and Mitsubishi) and the adjustment method varies depending on the specific maker.

14-1 CLEANING THE SCREEN

Since the Projector screen is susceptible to damage, pay careful attention to its handling. When cleaning, refrain from using water or volatile chemicals.

CAUTION!

When the screen surface ecomes dirty with dust, etc., clean it by using a soft cloth such as gauze. When water, and volatile chemicals such as enzine, thinner, etc., spill on the screen surface, it may be subject to damage, therefore, do not use them. Also, since the surfaces are susceptible to damage, refrain from rubbing them with a hard ——> fai ii rr

material or using a duster. i A

IAW hy \s

FIG. 14.1

Page 72

14-2 ADJUSTMENT OF TOSHIBA PROJECTOR

SETTING THE INTERFACE

In this product, set to INPUT LEVEL: 0.7V and IMPEDANCE: 75E@. Failure to observe this can cause CRT membrane to burn or Shutdown device to function resulting in power off.

IMPORTANT

The Projector's Connector Panel contains the Interface setting SW.

  • )
  • on WINNER AC IN Lat ©" RGB IN IMPEDANCE INPUT LEVEL

REMOTE CONTROL BUTTONS

When adjusting the Projector, direct the Remote Control's light emitting portion towards the Projector Screen.

REMOTE CONTROL LIGHT EMITTING PORTION

MODE (mode selection) WRITING (storing the data) ‘ ieee Fl ‘adjust/normal shift | ‘automatic color matching) TEST (adjust | shift) 7O © @ P( tic col hing) / te ene oll R.G.B. (color selection) << 1G 6 “6 al SET (to decide the selection) | e/ele - ane (item selection) (<x Posmion 5) POSITION (to select the position) =@ @ @ ‘| / | eee 4 RESET ra must)

ADJUST (adjustment) C) @ é V- SELECT (pattern selection)

oes SS!

Page 73

AUTOMATIC COLOR MATCHING

The Projector may be subject to color deviations affected by earth magnetism, the building steel frames, etc. When the Projector is initially installed or the Projector's installation position is changed, have the color matching performed automatically.

® Keep pressing the P button (red) for approximately 3 seconds to have

the ensuing movements performed automatically.

cE an The Projector will shift to the color deviation correction mode from the game mode, with the green cross pattern appearing on the screen.

The cross pattern moves up/down and right/ left to start the movement of searching the correct screen position and inclination.

When the green cross pattern movements are finished, similar detection is performed sequentially in order of red and then blue cross movements. After detecting by green, red and blue cross movements, the game mode returns with the color deviation status being corrected.

@ Although very rarely, the TRY AGAIN error display in red may appear. At this time, press the P button (red) for approximately 3 seconds. Even after the above operation is repeated, if the error condition still exists, then the display shifts to PLEASE ADJ. In this case, the auto color matching function can not be used. Contact the place of contact herein stated or where the product was purchased from.

@ Ifthe automatic color matching indicates an error, color matching can manually be performed. Refer to CONVERGENCE ADJUSTMENT (manual color matching).

Page 74

ADJUSTING THE ON-SCREEN CONTRAST

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, the on-screen contrast can be readjusted if desired. When the Game Board is replaced, readjustment may be necessary. Changing the CONTRAST causes the light and shade of the on-screen images to be changed.

>-6 Test S elelele e| SET C oe! efole Al -O.@ — Cow! A VW “ADJ @) Press either 4, or W PIC - ADJ button.

The on-screen menu will have one item in purple and 6 items in white. CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT

® Choose CONTRAST by using either 4 or W

PIC - ADJ button. Herein. CIO 5 faq \@ 4) ls procedure @ @ ¢ @ | V7 is skipped. Gee I @

SET

«ADJUST j Have CONTRAST dis- CONTRA Sim played in purple. Since H.POSI CONTRAST is selected Niece! initially, no particular V.SIZE operation is required in this EXIT case.

® Press the SET button (to decide selection). When the selection of the CONTRAST adjustment mode is decided, the adjustment data scale bar appears on the screen. CONTRAST 230 reese Siren ariel Trp

@ Make adjustment by using either < or > ADJUST button. As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen contrast status. ost Beene ra Sige ci sary >

WERTC © Press the WRITING button (for storing and finish).

The WRITING display appears and the adjustment data is stored.

WRITING

@ When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure (2) and press the SET button. @ To continue adjusting other menu items, repeat procedure e) ~ @ Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 75

ADJUSTING THE SCREEN BRIGHTNESS

Although the on-screen picture quality has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustment may be necessary. Changing the BRIGHTNESS causes the brightness of the on-screen images of black portions to be changed.

PIC-ADJ CONTRAST BRIGHTNESS, H.POSI V.POSI H.SIZE V.SIZE EXIT

  • ADJ button.

PIC-ADJ CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT /\ ® Press either 4 or W PIC - ADJ button. The on-screen menu will have one item in purple and 6 items in white.

@ Choose BRIGHTNESS by using either 4 or W PIC

Have the BRIGHTNESS displayed in purple.

SET (6) Press the SET button (to decide selection). When the selection of the BRIGHTNESS adjustment mode is decided, the adjustment data scale bar appears on the screen.

@ Make adjustment by using either <4 or > ADJUST « — AbUUST button.

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen brightness status.

‘o. 6) Press the WRITING button (for storing and finish).

WRITING The WRITING display appears and the adjustment data is stored.

@ = When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure @and press the SET button. @ To continue adjusting other menu items, repeat procedure @ ~ @ Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 76

ADJUSTING THE ON-SCREEN DISPLAY POSITION

Although the on-screen display position (H. POSI, V. POSI) has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustments may be necessary.

A ress either 4 or W PIC - ADJ button. The on-screen menu will have

PIC-ADJ CONTRAST

Vv BRIGHTNESS one item in purple and 6 items in

H.POSI white. V.POSI H.SIZE V.SIZE EXIT

@ Choose H. POSI or V. POSI by using either 4 or Vv

A PIC ADJ button. j Have the H. POSI or V. POSI

A PIC ADJ button V SRIGeee displayed in purple. The Figure

H.POSI shows the status in which H. V.POSI toate H.SIZE POSI is selected. V.SIZE EXIT

When the selection of the H. POSI or V. POSI is decided, the adjustment data scale bar appears on the screen.

@ Make adjustment by using either <q or > ADJUST el TESS button.

© © As the Cursor is moved, the

adjustment data value changes. When making adjustments Make adjustment so as to obtain in vertical directions, also the desired on-screen position use either <q or D> aie ADJUST button.

WRITING 6) Press the WRITING button (for storing and finish). The WRITING display appears and the adjustment data is stored.

WRITING

@ When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure @ and press the SET button. @ To continue adjusting other menu items, repeat procedure @ ~ @ Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 77

ADJUSTING THE SCREEN SIZE

Although the on-screen size (H. SIZE, V. SIZE) has been adjusted at the time of shipment from the factory, readjustment can be made if desired. When the Game Board is replaced, readjustments may be necessary.

@| @ of eee ree. ore) © Pap |@ @ ©

ejeiea A Y ®@ Y Vv PIC-ADJ <

«ADJUST j

When making adjustments in vertical directions, also use either <q or > button.

WRITING

the SET button. ® Press either 4 or W PIC - ADJ button.

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT The on-screen menu will have one item in purple and 6 items in white.

PIC - ADJ button. @ Choose H. SIZE or V. SIZE by using either 4 or W

CONTRAST BRIGHTNESS H.POSI V.POSI H.SIZE V.SIZE EXIT Have the H. SIZE or V. SIZE displayed in purple. The Figure shows the status in which H. SIZE is selected.

(6) Press the SET button

(to decide selection). When the selection of the H. SIZE or V. SIZE adjustment mode is decided, the adjustment data scale bar appears on the screen.

button. @) Make adjustment by using either <4 or > ADJUST

As the Cursor is moved, the adjustment data value changes. Make adjustment so as to obtain the desired on-screen position status.

® Press the WRITING button (for storing and finish).

WRITING The WRITING display appears and the adjustment data is stored.

To continue adjusting other menu items, repeat procedure @ ~ @®. Unless the adjustment data is stored, the data in the adjusted status will be erased at the time the power When discontinuing the adjustment, choose EXIT from the menu at the stage of procedure @ and press

is turned off and the pre-adjustment status will remain when the power is turned on next time.

Page 78

CONVERGENCE ADJUSTMENT (manual color matching)

A

CAUTION!

IMPORTANT

To avoid circuitry malfunctioning due to electrical load increase, never utilize CONVERGENCE ADJUSTMENT (Line Convergence Adjustment in particular) for adjusting screen size changes. There is no means to restore the Convergence Adjustment data once stored, to its original state. To avoid changing the screen size by erroneously using convergence adjustment, do not perform the green Line Convergence Adjustment. As such, be sure to perform the adjustment work from this page onward by the Technical staff and the location's Maintenance Personnel who are well versed in such adjustment work. In the Static Convergence Adjustments, if satisfactory adjustments can not be performed, do not make another convergence adjustments inadvertently. Contact the office herein stated or where the product was purchased from.

To avoid making the adjustment work ineffective, do not press the RESET button during adjustment.

To discontinue adjustment work, keep pressing the TEST button for approximately 3 seconds at the stage before storing the adjustment data by pressing the WRITING button. Should the screen be abnormally disturbed by noise due to static electricity, etc., turn the power off without storing the adjustment data. Pressing the & or W PIC - ADJ button in the Convergence Adjustment mode status will display the Adjustment Menu shown right. Do not ADJUST utilize this Adjustment Menu as this is the one applied at the factory. : . : SUB V. Adjusting this menu causes the SUB H. Customer's adjustment range to be SUB BRIGHT

deviated. EXIT

Should the menu shown right be displayed by mistake, first choose EXIT by using either & or W PIC - ADJ button and then press the SET button. Adjustment menu used in the factory.

Page 79

STATIC CONVERGENCE ADJUSTMENT

In the static convergence adjustment, each of red and blue images is comprehensively moved to and superimposed on the green color. If automatic color matching function is not sufficiently satisfactory, perform this adjustment. Be sure to perform automatic color matching before starting the above adjustment.

Keep pressing the TEST button for 1G) approximately 3 seconds. The screen will change to ADJUST mode from the Game mode to cause the green test pattern to be displayed on the screen. —ADIUS} MODE—

pie é P<

DO NOT PUSH THIS. O) Press the R button to have the red adjustment

mode. The red test pattern is added to the display. The frame color turns red and this signifies the red adjustment mode.

® Make adjustment by using the & W <q > When either of (2) (4) COLOR ADJUST buttons. SELECT buttons (R, B) is pressed, if the ape MODE Make adjustment so as to have color desired to be adjusted disappears, ted superimposed on green.

press that particular button again. For When 7 is superimposed =

example, if the red color needs to be yellow.

adjusted again at the stage of O) ,theR

button need to be pressed twice. @ Press the B button to have the blue adjustment mode.

Similarly as in the case of red, adjust the blue color. When green, red, and blue are superimposed, the color becomes white. [—AbIUdF MODE—

© Press the WRITING button (for storing and finish). The WRITING display appears and the adjustment data is stored. After the data is stored, the Game mode returns.

  • ADJUSP MODE—

wrifING

Page 80

POINT CONVERGENCE ADJUSTMENT

In the POINT CONVERGENCE adjustment, each of red, green and blue images is partially moved for color matching. The adjustment may be necessary when the Game Board is replaced or changed, or screen size is changed. Be sure to perform automatic color matching before starting the adjustment.

MARKER

Note | When the MODE button is repeatedly pressed, the adjustment modes will circulate as follows:

STATIC ADJUSTMENT MODE

LINE ADJUSTMENT MODE

POINT ADJUSTMENT MODE

When either of the COLOR SELECT buttons (R, B) is pressed, if the desired color to be adjusted disappears, press that particular button again.

Note 2
Note 3 By repeatedly pressing the SELECT button, only the Projector's TEST pattern screen and the screen superimposing the Game Board Test pattern can be alternately displayed. Keep pressing the TEST button for approximately 3 seconds. [= ADIUSF MODE— The screen changes to ADJUST mode from the Game mode and displays the green test pattern.

Press the MODE button twice to have the POINT ADJUSTMENT mode. Note 1

The crosshatch test pattern appears and the MARKER indicating the adjustment point is displayed.

R or B button, select the desired be adjusted. Note2 By using the G the green color can also be selected.

The selected color is displayed by superimposing on green. The MARKER will be in the color selected.

using the A Vv <q > ADJUST buttons, move the MARKER to the position to be adjusted. The MARKER moves in the direction of the button's arrow. However, the movable point is predetermined.

® Make adjustment by using the & W <q > ADJUST buttons. Although the direct vicinity of the MARKER's center moves most conspicuously, make adjustment by paying attention to the periphery area also. Shown left is the magnified MARKER periphery.

(G) Press the SELECT button as necessary to

superimpose Game Board images. Note 3 If the test pattern is not displayed in | the periphery of the screen, adjustments can be made by pressing the SELECT button to superimpose the | test pattern and the Game Board's CRT test screen.

s the WRITING button (for storing and finish). WRITING is displayed and the adjustment data is stored. After the data is stored, the Game Board screen returns.

Page 81

LINE CONVERGENCE ADJUSTMENT

Note 1
Note 2 In the LINE CONVERGENCE ADJUSTMENT, the adjustment point of the column line (vertical) or row line (horizontal) is comprehensively moved for color matching. It is convenient to utilize this adjustment when the color of the column line or row line is uniformly deviated.

When the MODE button is repeatedly pressed, the adjustment modes will circulate as follows:

STATIC ADJUSTMENT MODE

LINE ADJUSTMENT MODE

POINT ADJUSTMENT MODE

When either of the COLOR SELECT

buttons (R, B) is pressed, if the desired color to be adjusted disappears, press that particular button again. MARKER - Keep pressing the TEST button for approximately 3 seconds.

ge aes The screen changes to ADJUST mode from the Game Board mode and displays the green test pattern.

@ Press the MODE button once to have the POINT

ADJUSTMENT mode. Note 1

The crosshatch test pattern appears and the vertically long MARKER is shown.

® Using either R or B button, select the desired color to

be adjusted. Note 2 Although the green color can also be selected by using the G button, to avoid the screen size change adjustment, do not choose green. The selected color is displayed by superimposing on green. The MARKER will be in the color selected.

® By using the & Vv <4 > POSITION buttons, move the MARKER to the position to be adjusted. ADIOS: Use the <q p> buttons to select the column line, and the MARKER moves in the right/left direction. However, the movable range is predetermined.

Use the & W buttons to select the row line and the MARKER moves in the up/down direction. However, the movable range is predetermined.

it by using the & W < > ADJUST buttons. < e & € & Z 8g

The selected column line or row line (shown left is the column line) can be moved in the desired up/ down or right/left directions as applicable.

(G) Press the WRITING button (for storing and finish). WRITING is displayed and the adjustment data is stored. After the data is stored, the Game Board screen returns.

Page 82

14-3 ADJUSTMENT OF MITSUBISHI PROJECTOR

@ For the operation of Remote Control, use only the Keys of R/B, A (UP shift),<] (LEFT shift), W (DOWN shift), [> (RIGHT shift), TEST,

IMPORTANT

-,+,and PICTURE. Do not press keys other than those explained in this manual. @ When operating the Remote Control, have it point the screen.

The Projector has DYNAMIC CONVERGENCE adjustment functions. This manual does not refer to the functions as the adjustment of DYNAMIC CONVERGENCE is very troublesome and in addition, visual effects are negligible.

UP shift)KEY

R/B KEY

LEFT shift)KEY

DOWN shift)KEY

TEST KEY

~KEY MITSUBISHI

PICTURE KEY

Page 83

+ POWER KEY... ... This does not have power ON/OFF function. Does not function even if it is pressed. ... Used to select "R" for red adjustment or "B" for blue adjustment in the STATIC CONVERGENCE ADJUSTMENT mode.

*s(UP shift) KEY we Used to move the test cross upward in the STATIC CONVERGENCE ADJUSTMENT mode.

... Used to move the test cross to the left in the STATIC CONVERGENCE

  • << LEFT shift) KEY .... ADJUSTMENT mode.

... Used to move the test cross downward in the STATIC CONVERGENCE ADJUSTMENT mode.

+. (RIGHT shift) KEY........... Used to move the test cross to the right in the STATIC CONVERGENCE > ADJUSTMENT mode. *t (DOWN shift)...

© TEST KEY .......ceeeeeees. This is the ON/OFF key in the STATIC CONVERGENCE ADJUSTMENT mode. In the ON status of this key, the test cross pattern appears in the approximately on-screen center. « ENTER KEY.... ... Used for DYNAMIC CONVERGENCE.

© - KEY wo ... Used to decrease the adjustment data in the adjustment mode of CON- TRAST, BRIGHTNESS, HORIZONTAL/VERTICAL POSITIONS and WIDTH.

... Used to increase the adjustment data in the adjustment mode of CON- TRAST, BRIGHTNESS, HORIZONTAL/VERTICAL POSITIONS and WIDTH.

... Used for the ADJUSTMENT mode of CONTRAST, BRIGHTNESS, HORI- ZONTAL/VERTICAL POSITIONS and WIDTH. Every time this key is pressed, the ADJUSTMENT mode proceeds as + PICTURE KEY ....

follows:

NORMAL CONTRAST BRIGHTNESS H-POSI -—) OPERATION [>| ADJUSTMENT |—>| ADJUSTMENT }|—®> ADJUSTMENT MODE MODE MODE

V-HEIGHT V-POSI H-WIDTH ADJUSTMENT }¢—| ADJUSTMENT }«d—J ADJUSTMENT [ed MODE MODE MODE

EXPLANATIONS OF ADJUSTMENT MODES

  • CONTRAST .. Used to vary image contrast. Use + and - keys to adjust.
  • BRIGHTNESS .. Used to change image brightness. Use + and - keys to adjust. + H-POSI....................... Used to move the image position in the horizontal direction. Use + and - keys to adjust. + H-WIDTH .. Used to change the horizontal width of image. Use + and - keys to adjust. + V-POSI. Used to move the image position in the vertical direction. Use + and - keys to adjust. © V-HEIGHT ........ Used to change the vertical width of image. Use + and - keys to adjust.
Page 84

STATIC CONVERGENCE ADJUSTMENT

RED 31K

Press the TEST KEY to change the screen to Red Line HTS Vell Adjustment mode.

Superimpose the red line on the green line. When the red line is superimposed on the green line, the green line turns to yellow or white. a

To MOVE RED LINE: Use <j key to move it left. Use [> key to move it right. Use s key to move it upward. V

Use t key to move it downward.

Press the R/B KEY. Changes to the Blue Line Adjustment screen. Every time the key is pressed, "from red to blue" and "from blue to red" are alternated.

5 : <J > SUPERIMPOSING BLUE LINE ON GREEN LINE: B < > Superimposing blue line on green line causes the green A line to turn to white.

TO MOVE BLUE LINE: Use <J key to move it left. Use > key to move it right. Use s key to move it upward. Use t key to move it downward.

Press the TEST KEY. Adjustment is finished.

AUTOMATIC CANCELLATION OF ADJUSTMENT MODE

In each adjustment mode, only in the case where an effective key input (variation of values and images) is not performed within the time limit indicated below, the adjustment mode is automatically cancelled and finished, shifting to on-screen normal images.

Approximately 6 seconds +=CONTRAST BRIGHTNESS H-POSI H-WIDTH V-POSI V-HEIGHT Approximately 5 min. STATIC CONVERGENCE

Page 85

15. REPLACING THE FLUORESCENT LAMP, AND LAMPS

When performing work, be sure to turn power off. Working with power on can cause electric shock and short circuit hazards.

WARNING! The Fluorescent Lamp, when it gets hot, can cause burn. Be very careful

when replacing the Fluorescent Lamp. Be sure to use lamps of the designated rating. Using lamps of undesignated rating can cause a fire or malfunctioning.

To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Performing work without using the step can

CAUTION! cause violent falling down accidents. Be careful when handling the plastic made parts. Failure to observe this may cause injury due to damage or fragments resulting from damage.

THE FLUORESCENT LAMP INSIDE THE MAIN BILLBOARD

@tum off power. @ Take out the 3 screws to remove the SASH.

TRUSS SCREW (3)

M4 X 16,chrome

PHOTO 15a

When performing work, be sure to use a step.

PHOTO 15b

Page 86

@ Remove the MAIN BILLBOARD PLATE.

PHOTO 15c¢

@ Replace the fluorescent lamp inside the BILLBOARD.

PHOTO 15d \FLUORESCENT LAMP 32W: 390-5251-32-01

Tan BILLBOARD PLATE

GLOW BULB: 390-5638-5P

THE BUTTON FOR THE HORN IN THE ASSISTANT DRIVER'S SEAT

A wiring connection is inside the horn button. When removing, use care so as not to damage wiring.

® Turn power off.

@ Remove the 4 screws.

PHOTO I5e TRUSS SCREW (4) M4 X 16,chrome

Page 87

® A wire connector is connected to the horn

button. Disconnect the connector, and the horn button can be removed.

@ Firmly pinch the switch portion at the

bottom of the button and pull it out of the button portion.

© Pull out the lamp vertically and replace. Do not turn the lamp at this time. Disconnect the connector.

PHOTO 15 f

LAMP14V 3.8W 390-6677-038

PHOTO 15 g

START BUTTON & VIEW CHANGE BUTTON

A wiring connection is inside the start button and the view change button. When removing, use care so as not to damage wiring.

® Turn power off.

@ Take out the 4 screws.

PHOTO 15h

TRUSS SCREW (4) M4 X 16,chrome

Page 88

(6) A connector is connected to the start

button and the view change button. Disconnect the connector, and the ASSY VR BUTTON START & VIEW | can be removed.

Se Disconnect the connector.

PHOTO 15i

@ The lamp is on the PCB side. Turn the metallic parts of the 2 buttons, unlock and remove the PCB from the buttons.

PHOTO 15j

® With the lamp pressed down, turn it

counterclockwise to remove.

PHOTO 15k

Page 89
  • PERIODIC INSPECTION TABLE The items listed below require periodic check and maintenance to retain the performance of this machine and to ensure safe business operation. A\ @ Be sure to check once a year to see if Power Cords are damaged, the plug is securely inserted, dust is accumulated between the Socket Outlet and the
WARNING! Power Plug, etc. Using the product with dust as is accumulated can cause fire and electric shock hazards. Periodically once a year, request the place of contact herein stated or the Distributor, etc. where the product was purchased from, as regards the internal cleaning. Using the product with dust as is accumulated in the interior

without cleaning can cause a fire or accident. Note that cleaning the interior

parts can be performed on a pay-basis.

TABLE 16

Item Interval Reference

CABINETCheck Adjusters'contact with surface.Daily3
HANDLE MECHACheck lamp.Monthly9

Check VOLUME VALUE. Monthly 9

Check ADJUST GEAR engagement.Trimonthly10-2

ACCEL. & BRAKE Check VOLUME value. Monthly 69

Check ADJUST GEAR engagement.Trimonthly12-2
Gear and Spring portion greasing.Trimonthly12-3

SHIFT LEVER Check SW. Monthly 6,9 COIN CHUTE TOWER] Check COIN SW. Monthly 9

Coin insertion test.Monthly13
Cleaning of COIN SELECTOR.Trimonthly13

PROJECTOR SCREEN cleaning. Weekly 14-1

Check adjustments.Monthly6,9,14
GAME BDMEMORY TEST.Monthly9
Check settings.Monthly9
Cabinet surfacesCleaningAs necessary.See below.
INTERIORCleaningAnnuallySee above.

POWER SUPPLY PLUG Inspection and cleaning

CLEANING THE CABINET SURFACES

When the cabinet surfaces are badly soiled, remove stains with a soft cloth dipped in water or diluted (with water) chemical detergent and squeezed dry. To avoid damaging surface finish, do not use such solvents as thinner, benzine, etc. other than ethyl alcohol, or abrasives, bleaching agent and chemical dustcloth.

Page 90
  • TROUBLESHOOTING

WARNING! bd

In order to prevent electric shock and short circuit, be sure to turn power off before performing work. Be careful so as not to damage wirings. Damaged wiring can cause electric shock or short circuit. After removing the cause of the functioning of the Circuit Protector, reinstate

the Circuit Protector. Depending on the cause of the functioning, using the

Circuit Protector as is without removing the cause can cause generation of heat and fire hazard.

In case a problem occurs, first check wiring connector connections.

TABLE 17a

PROBLEMS

With Main SW ON, no activation. CAUSE

Power is not supplied.

Power supply/voltage is not correct.

The Circuit Protector functioned due to the momentary overload. COUNTERMEASURES

Securely insert the power plug into the plug socket.

Make sure that power supply/voltage is correct.

After eliminating the cause of overload, reinstate the AC Unit's Circuit Protector (see 5 , Section 6, Refer to the following).

The color on PTV screen is incorrect. Image adjustment is inappropriate. Adjust appropriately (see Sec. 14).

Color deviation on PTV screen. Affected by peripheral machines or the building's steel frames. Perform convergence adjustment (see Sec. 14).

Change installation direction or position.

Move the machine which causes the problem.

CIRCUIT PROTECTOR

&

FIG. 17a CIRCUIT PROTECTOR

Functions due to the activation of bimetal. To restore the function, wait for approximately one minute or longer until the bimetal cools off. (Press the Button.)

Page 91

TABLE 17 b

PROBLEMS

No sound is emitted. CAUSE

Sound volume adjustment is not appropriate.

Board and Amplifier malfunctioning. COUNTERMEASURES

Adjust sound volume (see Sec. 9).

Perform the sound test and confirm (see Sec. 9).

Operation of Super Woofer and Base Shaker are not satisfactory. The fuse on the AMP BASE is blown. Replace fuse. (see Fig.17b)

Steering Wheel reaction strength is incorrect. Deviation of Center. Power ON check not performed correctly.

V.R. position deviated.

V.R. malfunctioning. Turn off power and then turn it back on again. Complete the power on check.

Adjust V. R. value in the test mode (see Sec. 9).

Replace V.R. (see Sec. 10).

Steering Wheel reaction strength is insufficient. Reaction Mecha's secular change. Change the setting in the Test Mode (see Sec. 9).

No Steering Wheel Reaction. Connector Connection is incorrect. Check the connector's connection inside the LID TOP FRONT. (see 10-1)

SHIFT LEVER doesn't operate satisfactorily. Switch malfunctioning. Replace the Switch (see Sec. 11).

Operation of Accel. and Brake Pedals are not satisfactory. V.R. malfunctioning.

ADJUST GEAR's engagement is not correct. Replace the V.R. (see Sec. 12).

Adjust the engagement of ADJUST GEAR (see Sec. 12).

The Fluorescent lamp does not light up. Connector connection fault.

The Fluorescent tube is burnt out. Check connector connection (see Sec 6).

Replace the Fluorescent tube (see Sec. 15).

Page 92

REPLACMENT OF FUSE

Fuse replacements other than those specified can cause accidents and are strictly forbidden. In case fuse replacements other than those stated in this

WARNING! manual are necessary, contact where you purchased the product from for

inquiries regarding this matter.

n order to prevent an electric shock, be sure to turn power off and unplug

from the socket outlet before performing work by touching the internal parts of the product. Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit accidents. Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause fire and electric shock accidents. After eliminating the cause of the blowing of fuse, replace the fuse. Depending on the cause of fuse blowing, continued use with the fuse as is lown can cause generation of heat and fire hazard.

® Turn power off.

@ Take out the 2 truss screws, unlock and remove the BACK LID from the main cabinet. @ The fuse is provided at the right-hand side of the BACK LID inside.

TRUSS SCREW (2) \ M4 X 25,black

BACK LID

FIG. 17b FUSE 6.3A. 314-5086-6300 |

Page 93
  • GAME BOARD

In order to prevent electric shock and short circuit hazards, be sure to turn power off before performing work.

WARNING! Be careful so as not to damage wirings. Damaged wiring can cause fire,

electric shock or short circuit. Do not expose the Game BD, etc. without a good reason. Failure to observe this can cause electric shock hazard or malfunctioning.

In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, etc. as is with the same setting made at

CAUTION! the time of shipment so as not to cause electric shock and malfunctioning.

18 - 1 REMOVING THE BOARD

®© Turn power off.

®© Turn power off @) Take out the 2 truss screws,

unlock and remove the BACK. LID from the main cabinet. f

TRUSS SCREW oN

M4 X 25,black

BACK LID

FIG. 18.1

® Disconnect all

connectors connected to the NAOMI GAME BOARD.

PHOTO 18. 1a

Disconnect the connector|

Page 94

@® Disconnect the 4 connectors connected to

the IC BOARD next to the NAOMI GAME BOARD. It is not necessary to disconnect the leftmost 2 connectors out of the 3 connectors on the IC BD.

® Pull out the 8P connector at the AMP BD

side.

PHOTO 18. 1b Disconnect the connector

© Untie cord clamps and harness lugs which

secure wiring.

Disconnect the connector

PHOTO 18. 1c

Take out the 2 screws which secure the wooden base carrying the NAOMI GAME BOARD.

SCREW (2) M4 X 25,w/flat & spring washers

PHOTO 18. 1d

Pull the base with the NAOMI GAME

BOARD on it out of the main cabinet. At

this time, use care so as not to damage wiring.

(©) Take out the 4 screws to remove the

NAOMI GAME BOARD from the base.

PHOTO 18. Le SCREW (4) M4 X 16,w/flat & spring washers

Page 95

18 - 2, COMPOSITION OF GAME BOARD

this may cause functioning not suitable for the actual operation, or malfunctioning.

S Ensure that the DIP SW setting is performed as designated. Failure to observe

IMPORTANT

ASSY CASE NAO PTR USA(840-0023D-01):USA ASSY CASE NAO PTR EXP(840-0023D-02):0THERS ASSY CASE NAO PTR KOR(840-0023D-03):KOREA ASSY CASE NAO PTR AUS(840-0023D-04): AUSTRALIA

SCREW (4) a

ROM CASE NAO PTR 840-0023C

DIP SW. 840-0001A-01 ASSY CASE NAOMI MAIN BD USA 840-0002A-01 ASSY CASE NAOMI MAIN BD EXP. 840-0003A-01 ASSY CASE NAOMI MAIN BD KOR, 840-0004A-01 ASSY CASE NAOMI MAIN BD AUS

FIG. 18.24

FIG. 18.2a

DIP SW

In this product, set the DIP SW to OFF. There is another DIP SW on the IC BOARD (other than NAOMI GAME BOARD). Set this DIP SW to OFF as well.

FIG. 18.2b

Page 96

18 - 3 ERROR DISPLAY (DRIVE CONTROL BOARD)

WARNING! Be careful so as not to damage wirings. Damaged wiring can cause electric shock and short circuit hazards. Do not touch undesignated places. Touching places not specified can cause electric shock and short circuit hazards.

Inside the LID TOP FRONT is the Drive Control Board. If an irregularity occurs in the Drive Control Board, the ERROR message is shown on the screen and the 7-SEG display on the Drive Control Board. Take countermeasures in the manner corresponding to the ERROR message.

Note that even in the case an error occurs, game is playable. Errors can be classified roughly into 2 types, such as communication related errors between Drive Control Board & Game Board and the others. If an error relating to communication occurs, "MOTOR NETWORK ERROR IN: XX OUT: XX" is displayed on the monitor. "MOTOR TROUBLE CODE: XX" is displayed when an error relating to other than communication occurs. For communication error display, the value outputted by NAOMI Board and the value corresponding to the NAOMI 's value outputted by Drive Control Board are displayed. Under normal operation, these values are identical. However, if an irregularity occurs, the values are not identical and the results are displayed on the monitor. If an irregularity relating to other than communication occurs, an error code is displayed. On-screen ERROR display differs from 7-SEG display on the Drive Control Board. For an error code and its countermeasures, refer to Table 18.3.

Table 18. 3 ERROR DISPLAY

On-screen 7-SEG display on ERROR display Drive Control BD. ERROR CAUSE/COUNTERMEASURES,

e7ER OLROM ERRORMalfunctioning of Drive Control Board.

Replace Drive Control Board.

e6ER 02RAM ERROR
e0ER 20InitializationIrregularity during initialization setting movement.

setting Finish initialization setting movement by turning irregularity of power off and then on. Note that when ERROR is motor displayed,the malfunctioning relates to the Motor System (Motor, Drive Control BD which controls the Motor, Drive BD., wirings in between, etc.)

0ER 22Steering Wheel's | Malfunctioning during initial setting movement.

centering error Finish initialization setting movement by turning power off and then on. Note that when ERROR is displayed, the malfunctioning relates to the Steering Wheel Volume system.

elER 23ERROR of theMalfunctioning which occurs during operation.

Encoder First turn the power off and after 10 min., turn it back incorporated in on again. Note that when this Error is displayed, the the motor. malfunctioning relates to the Motor System.

e2ER 24Overcurrent

ERROR

3ER 25Overheat

Overload

eaER 30VOLUMEMalfunctioning which occurs during operation.

ERROR Check the variation of the volume value in the test mode.

Page 97

Among the ERROR display as per Table 18.3, each of Er 01, 02, 20 and 22 (Error Code e7, 6, 0 and 9) is displayed before the Advertise mode is displayed if an irregularity is found during initialization setting movements when power is turned on. From among error displays as per Table 18.3, Er 23, 24, 25, and 30 (Error Code el, 2, 3 and a) indicate On-Board 7-SEG error display when an irregularity is found during game and ADVERTISE mode. If an irregularity is found during game, game play can be continued without Steering Wheel reaction. If Error display is shown on the screen, remove LID TOP FRONT without turning power off to check the 7-SEG display on the Drive Control Board. At this time, if the power is turned off, each of Er 23, 24, 25 and 30 (Error Code el, 2, 3 and a) which could have occurred during operation may not be displayed. Perform the DIP SW setting on the DRIVE CONTROL BOARD as shown below.

DRIVE CONTROL BOARD

PHOTO 18.3 DIP SW #1 1 2 3 4 5 6 7 8 OFF | OFF | OFF | OFF | OFF | OFF | OFF | OFF

DIP SW #2

1 2 3 4 3 6 7 8 ON | ON | ON | ON | ON | OFF | ON | OFF

(ai a] | g DIP SW

FIG. 18.3

Page 98

STICKER PTV SIDEL —_

STICKER PTV SIDE R

PTR-1026-01 (For OTHERS)

PLAY INSTR SH PTR ENG A

PTR-1026-02 (For KOREA) PLAY INSTR SH PTR ENG B | PTR-2601

STICKER VR BUTTON

PTR-2530 1 | STICKER MUFFLER

SUB BILLBOARD PLATE

PTR-1502

MAIN BILLBOARD PLATE

PTR-1024

STICKER BACK PLATE COVER

if nt Hin UUUUUL I PTR-1085 STICKER GRILLE PATTERN

PTR-1003-C STICKER MUFFLER UNDER

PTR-1006 CONT PNL PLATE For the Warning Display stickers, refer to Section 1.

  • DESIGN RELATED PARTS
Page 99

@ptR-0500

ASSY PTV

@prr-0550

ASSY PTV BASE

@ Top assy PTR DX @PtR-1000

ASSY MAIN CABINET

G@PTR-1600

ASSY SUB BILLBOARD

@ptR-0510 PTV W/STICKER PTR

  • @PTR-1100

ASSY SUB-CABI

  • (2)PTR-1060 AC UNIT
  • (3)PTR-1070 ASSY PILLAR L -— (4)PTR-1075 ASSY PILLAR R
  • (15)PTR-1080 ASSY BACK PANEL
  • (16)PTR-1200
  • (18)PTR-1500
  • (9)PTR-2100 t— @d)sPG-2200 ASSY COINCHUTE TOWER, ASSY MAIN BILLBOARD ASSY HIGHT/LOW/BACK SHIFTER ASSY ACCEL&BRAKE @prr-1190 ASSY BACK LID @prr-6001 ASSY WIRE (OstR-1070 FAN UNIT (stR-1070-01 FAN UNIT OPPOSITE FLOW
  • PARTS LIST

@ny-1180 SW UNIT

  • @i)PTR-2500 t— @3PTR-2600
  • @a)PTR-4000 ASSY MAIN BD +— @5)PTR-4100 ASSY CONTROL BD
  • @e)PTR-4200 ASSY AMP BD
  • @7)PTR-4300 ASSY PWR SPLY ASSY HANDLE MECHA ASSY VR BUTTON START AND IVIEW @)ptR-2550 SENSOR UNIT
  • @8)pTR-2590 ASSY TOP PLATE HANDLE MECHA
Page 100

C) Top Assy PTR DX (D-1/2)

Page 101
  • Top ASSY PTR DX

ITEM NO. PART NO.

PTR-0500 PTR-0550 PTR-1000 PTR-1600 421-7308- ~ 440-CS0186-EG 440-WS0002XEG 421-7020 421-8479-01 SGM-4365 421-11245-01 440-CS0205-EG 440-CS0206-EG

030-000830-S 068-852216 000-T00540-0C 068-552016-0C 000-T00516-0C 068-552016-0C 008-T00412-0B

601-6604-70 SGM-2675 420-6545-01 390-6677-038 600-6729 600-6618 600-6695 SGM-4111 220-5576 514-5086-6300 280-5009-01 420-6455-01 509-5636 220-5484 220-5373

105-5356 421-8740 421-6690-03 421-6690-05 421-6690-06 421-6690-01 421-6119-91 421-6120-92 (D-2/2)

DESCRIPTION NOTE

ASSY PTV ASSY PTV BASE ASSY MAIN CABINET ASSY SUB BILLBOARD DENOMI SH 1GAME, ~ STICKER C EPILEPSY 40 ENG STICKER W POWER OFF ENG. STICKER CAUTION FORK. STICKER INSTR SUNLIGHT ENG POLY COVER 1700 X 2200 X 1700 STICKER CAPACITY 2 SEATS ENG STICKER C PTR FOR CHILD ENG STICKER C PTR FOR PROTECTOR EG

HEX BLT W/S M8 X 30 FLT WSRR 8.5-22 X 1.6 M SCR TH CRM MS X 40 FLT WSHR CRM 5.5-20 X 1.6 M SCR TH CRM MS X 16 FLT WSHR CRM 5.5-20 X 1.6 TMP PRF SCR TH BLK M4 X 12

CARTON BOX 70 POLYETHYLENE BAG, 240 X 370 OWNERS MNL PTR DX ENG LAMP WB 14V 3.8W (194) AC CABLE CONNECT TYPE 154 AC 110V AREA AC CABLE CONNECT TYPE FOR EXP = AC 220 ~ 240V AREA AC CABLE CONNECT TYPE USA 15A_— AC 120V AREA KEY BAG (SGB-1035X) KEY MASTER FOR 220-5575 FUSE S.B 6300MA 250V HBC CE CORD CLAMP 21 SERVICE MANUAL NAOMI ENG. SW MICRO TYPE SS-SGL2T VOL CONT B-SK OHM VOL CONT B-5K

SHIPPING BRKT

CAUTION INSTR COP U/R STICKER 220V AC 220V AREA STICKER 240V AC 240V AREA STICKER 110V AC 110V AREA STICKER 120V AC 120V AREA STICKER FCC S USA STICKER SEGA USA =
Page 102

@) Assy PTV (PTR-0500)

ITEM NO. PART NO.

1 PTR-0510 2 MGL-1150 3 HOD-1101 4 RAL-0501

201 000-F00412 202 000-P00516-W 204 000-P00520-W 205 000-T00525-0C 206 068-552016-0C

DESCRIPTION NOTE

PTV W/STICKER PTR ASSY MASK PTV HOLDER MASK HOLDER

M SCR FH M4 X 12 M SCR PH W/FS MS X 16 M SCR PH W/FS MS X 20 M SCR TH CRM MS X 25 FLT WSHR CRM 5.5-20 X 1.6

Page 103
  • PTV W/STICKER PTR (PTR-0510)

ITEM NO. PART NO. DESCRIPTION NOTE

1PTR-0511STICKER PTV SIDE L
2PTR-0512STICKER PTV SIDER
101200-5788-31PROJECTION DSPL T SOTYPE 31K.

200-5799-31 PROJECTION DSPL M SOTYPE 31K

Page 104

G) ASSY PTV BASE (PTR-0550)

ITEM NO. PART NO.

1 PTR-0551 2 SCR-1008 3 ARC-1006 4 117-5233

101 601-9377 102 601-5699X

201 050-H01600-0B 202 030-000630-SB 203 011-P03512 204 030-000625-WB

DESCRIPTION NOTE

PTV BASE NUT PLATE FOR CASTER LEG BRACKET PLATE LEG BRACKET BLACK

CASTER FAI=75 LEG ADJUSTER BOLT M16 X 75

HEX NUT BLK M16 HEX BLT BLK W/S M6 X 30 TAP SCR PH 3.5 X 12 HEX BLT W/FS BLK M6 X 25

Page 105

(S) ASSY SUB BILLBOARD (PTR-1600)

ITEM NO. PART NO. DESCRIPTION NOTE

1PTR-1601SUB BILLBOARD BASE
2PTR-1602SUB BILLBOARD PLATE
3PTR-1604SIDE PLATE L

4 PTR-1605 SIDE PLATER

201000-T00412-0CM SCR TH CRM M4 X 12
Page 106

(D-1/4)

Page 107
  • ASSY MAIN CABINET (PTR-1000) (D-2/4)
Page 108

© ASSY MAIN CABINET (PTR-1000) (D-3/4)

ITEM NO. PART NO. DESCRIPTION NOTE

1PTR-1070ASSY PILLAR L
2PTR-1075ASSY PILLAR R
3PTR-1080ASSY BACK PANEL
4PTR-1100ASSY SUB-CABI
5PTR-1200ASSY COINCHUTE TOWER
6PTR-1500ASSY MAIN BILLBOARD
7PTR-2100ASSY HIGH/LOW/BACK SHIFTER,
8PTR-2500ASSY HANDLE MECHA

9 PTR-4000 ASSY MAIN BD

10 PTR-4100 ASSY CONTROL BD 12 PTR-4300 ASSY PWR SPLY

11PTR-4200ASSY AMP BD
13PTR-2600ASSY VR BUTTON START AND 1 VIEW
14SPG-2200ASSY ACCEL & BRAKE
15PTR-1001SEAT
16PTR-1002SEAT BACK
17PTR-1004END CAP

18 PTR-1005 CONTROL PANEL COVER

19PTR-1006CONT PNL PLATE
20PTR-1007DESIGN PIPE
21PTR-1008STEP
22PTR-1010SPKR BRKT
23PTR-1011PLATE HORN BUTTON
24PTR-1013LID TOP FRONT
25PTR-1014WIRE COVER
26PTR-1015ACCEL BRKT
27PTR-1016END CAP BRKT UPPER

28 PTR-1018 PIPE JOINT BRKT

29PTR-1019BACK PANEL COVER
30PTR-1020PILLAR CABI BRKT UPPER
31PTR-1021PILLAR CABI BRKT LOWER

32 PTR-2501 STEERING HANDLE

33STW-3031WOOFER BRKT
34PTR-2507COLLAR HANDLE SHAFT
35PTR-2508WSHR HANDLE SHAFT
36PTR-2509COLLAR STEERING HUB
37PTR-2510ROD HORN BUTTON
38PTR-1060AC UNIT
39PTR-2512COMP SPRING HORN BUTTON
40PTR-2513FRM HORN BUTTON
41PTR-2514CAP HORN BUTTON
42PTR-2525CUSHION L
43PTR-2526CUSHION U
44PTR-2527PIN HORN BUTTON
45PTR-1023PIPE SAFETY
46440-WT0192-EGTAG W LAMP ENG
47PTR-1022TOWER SHELF
48PTR-1024STICKER BACK PANEL COVER
49PTR-1026-01PLAY INSTR SH PTR ENG AOTHERS

PTR-1026-02 PLAY INSTR SH PTR ENG B KOREA

50PTR-2530STEERING HORN MARK
51PTR-1115WOOFER NET
53PTR-1027SPEAKER SPACER CUSHION
Page 109

©) ASSY MAIN CABINET (PTR-1000) (D-4/4)

ITEM NO. PART NO.

130-5096 130-5196 130-5172 509-5966 280-5275-SR10 280-0419 270-5117 601-0460

000-T00412-0C 000-P00420 050-H01600 000-T00425-0C 030-000640-SB 060-F00600-0B 030-000840-SB 068-852216 000-T00550-0B 011-T03512 000-P00408-W 068-552016-0B 030-000625-SB 068-652016-0B 030-00825-S 000-P00530 060-S00500 068-441616-0C 050-H00800 000-T00416-0B 068-441616-0B 000-P00420-WB 000-T00430-0B 000-T00416-0C 000-T00630-0B 050-F00400 000-T00516 000-P00512-W 060-F00400

PTR-60021 PTR-60028 PTR-60034 PTR-60033 DESCRIPTION NOTE

ASSY SERVO SPEAKER BOX WOOFER 40HM 80W BASS SHAKER SW PB OBSA-60UM 14V 3.8W PTR. CORD CLAMP SRI10 HARNESS LUG FERRITE CORE TDK ZCAT3035-1330 PLASTIC TIE BELT 100 MM

MSCR TH CRM M4 X 12 M SCR PH M4 X 20 HEX NUT M16 MSCR TH CRM M4 X 25 HEX BLT W/S BLK M6 X 40 FLT WSHR BLK M6 HEX BLT W/S BLK M8 X 40 FLT WSRR 8.5-22 X 1.6 MSCR TH BLK M5 X 50 TAP SCR TH 3.5 X 12 M SCR PH W/FS M4 X 8 FLT WSHR BLK 5.5-20 X 1.6 HEX BLT W/S BLK M6 X 25 FLT WSHR BLK 6.5-20 X 1.6 HEX BOLT W/S M8 X 25 M SCR PH MS X 30 SPR WSHR MS FLT WSHR CRM 4.4-16 X 1.6 HEX NUT M8 MSCR TH BLK M4 X 16 FLT WSHR BLK 4.4-16 X1.6 M SCR PH W/FS BLK M4 X 20 MSCR TH BLK M4 X 30 MSCR TH CRM M4 X 16 MSCR TH BLK M6 X 30 FLG NUT M4 MSCR TH MS X 16 M SCR PH W/FS MS X 12 FLT WSHR M4

WIRE HARN BASS WIRE HARN HORN SUB WIRE HARN VR BUTTON WIRE HARN MOTOR CONTROL

Page 110

ASSY STEERING UNIT

PTR-2524 Collar B

PTR-2523 Collar A

PTR-2503 Stopper Block 999-0989 Screw Sck Hex 10-32x3/4" Hardened 18 Wheeler Std Steering Shaft Assembly

a ca PTR-2506 H Stopper Ring B Assy ** See Drawing \ 100-5357 18 Wheeler Std, Back ' Bearing 8 ‘ for detail of this area 999-0948 Ring Retainer, Bearing

PTR-2505 Stopper Ring A Assy ** 100-5357 Bearing 8 *#999-0948 Ring Retainer, Bearing

999-0941 Rack & Pinion Assy Do not open, Spring and roller bearings under pressure. (Individual Parts not available)

999-0945 Hub, Spline 999-0991 Ring Retainer, Bearing *Screw Phillips #6-32x3/8" w/Lock Washer (2)

100-5052 Bearing, 6007ZZ

999-0951 Washer, Bearing Large SS 999-0955 Shaft, Steering

999-0936 Steering Wheel

999-0938 Spring, Horn

999-0939 Bushing Horn

  • Local Purchase ** Included in Assembly Sty 999-0981 Nut 5/8+11 Nyloc

999-0937 Horn Button

999-0980 Screw 1/4-20x1 3/4" Tamper Proof Torx (4)

D. Davidson 8/14/00 RevA

Page 111

18 Wheeler Standard Steering Assembly

Back

999-0973 VR Bkt 1 10-32x 1/2" w/Flat Washer 999-0947 Gear, Pot 90 *Screw 6-32x1/2" (2) 999-0943 Coupling, Pot Gear 999-0942 SK Pot, Long Life Imperial 998-0134. Optical Coupler 999-0950 Opto Bd Assy 999-0977 1/8" Spacer (2) 999-0959 Stopper Rubber 999-0978 Stopper Bracket *Screw Phillips #10-32x1/2" w/Lock Washer (4) ASSY HANDLE MECHA

999-0946 Gear, Main Shaft 30 *Set Screw Hex 6-32x1/4" (2)

999-0949 Ring Retainer, Bearing *Screw Phillips #6-32x3/8" w/Lock Washer (2)

| 999-0944 Bearing, 37 mm OD. 25 mm ID, 7 mm Thick

999-0952 Washer, Bearing Small “Screw Phillips 10-32x 1/2" w/Flat Washer (2)

See "Detail A" for parts identification of Tension Unit.

*Screw Phillips #4-40x 1/2" (2) 999-0990 Bracket, Opto 1s 10-32x 1/2"

  • LOCAL PURCHASE 999-0975 * #10-32 Nut (2)

#10 Shoulder Bolt (2) 999-0940 Friction Block - Nylon 999-0976 Spring (2) ‘999-0974 Tension Bracket

Detail A D. Davidson 8/14/00 RevC

Page 112

@) ASSY SUB-CABI (PTR-1100) (D-1/3)

Page 113

@) ASSY SUB-CABI (PTR-1100)

ITEM NO. PART NO.

1 PTR-1190 2 PTR-1012 3 STR-1070 4 PTR-1101 5 PTR-1102 6 PTR-1103 7 PTR-1104 8 PTR-1107 9 PTR-1108 10 PTR-1109 11 PTR-I111 12 PTR-1112 13 PTR-1113 14 PTR-1114 16 ARC-1006 17 117-5233 18 253-5460-01 19 PTR-1116 20 STR-1070-01 21 PTR-1121 22 PTR-1122 23 PTR-1119 24 PTR-1120

101 601-9377 102 601-5699X 103 280-5009-01 104 280-0419 105 601-0460 106 117-5402-06 107 280-5275-SR10

201 000-T00420-0B 203 FAS-000070 204 079-000008 205 030-000630-SB 206 050-H01600-0B 207 000-P00416-WB 208 011-P00412 209 011-F00312 210 011-T03512 211 011-F03516 212 068-652016-0B 213 030-000625-WB (D-2/3)

DESCRIPTION NOTE

ASSY BACK LID BRKT HORN BUTTON FAN UNIT MAIN CABINET SEAT BRKT SEAT BRKT UPPER BACK PLATE DUMMY SHAFT CTRL COVER BRKT A CTRL COVER BRKT B SHIFTER BRKT A SHIFTER BRKT B CTRL PNL REINFORCE JOINT BRKT LEG BRACKET PLATE LEG BRACKET BLACK AIR VENT BLACK SASH PTV FAN UNIT OPPOSITE FLOW STICKER CABI L STICKER CABIR WATER SEAL 865X10 TS WATER SEAL 120X10 TS

CASTER FAI=75 LEG ADJUSTER BOLT M16 X 75 CORD CLAMP 21 HARNESS LUG PLASTIC TIE BELT 100 MM EARTH TERMINAL PLATE 6P CORD CLAMP SRI10

MSCR TH BLK M4 X 20 MSCR TH BLK M6 X 25 SCR NAIL THH STNLS 1.5 X 16 HEX BLT BLK W/S M6 X 30 HEX NUT BLK M16 M SCR PH W/FS BLK M4 X 16 TAP SCR PH 4 X 12 TAP SCR FH 3 X 12 TAP SCR TH 3.5 X 12 TAP SCR FH 3.5 X 16 FLT WSHR BLK 6.5-20 X 1.6 HEX BLT W/FS BLK M6 X 25

Page 114

@) ASSY SUB-CABI (PTR-1100)

ITEM NO. PART NO.

301 PTR-60005 302 PTR-60006 303 PTR-60031 304 PTR-60032 305 PTR-60103 306 600-6972-1200 307 600-6972-1800 308 600-6972-0750 309 PTR-6001 310 PTR-60102 (D-3/3)

DESCRIPTION NOTE

WIRE HARN AC FRONT WIRE HARN AC BACK WIRE HARN MOTOR, WIRE HARN ENCODER, WIRE HARN EARTH SHIFTER WIRE HARN EARTH IDS 1200MM WIRE HARN EARTH IDS 1800MM WIRE HARN EARTH IDS 0750MM ASSY WIRE WIRE HARN EARTH PEDAL

Page 115

ASSY BACK LID (PTR-1190)

ITEM NO. PART NO. DESCRIPTION NOTE

1PTR-1191BACK LID
2DP-1148XLKG TNG
3117-0062PLATE LOCK RETAINER
4253-5460-01AIR VENT BLACK
101220-5575CAM LOCK MASTER W/O KEY
201000-T00416-0BMSCR TH BLK M4 X 16
Page 116

@) ASSY WIRE (PTR-6001)

ASSY WIRE (PTR-6001) is comprised of the following wire harnesses. An ASSY DRG. is unavailable.

ITEM NO. PART NO. DESCRIPTION NOTE

101601-0460PLASTIC TIE BELT 100 MM
301PTR-60018WIRE HARN WOOFER 2
302PTR-60019WIRE HARN SPEARKER 2
303PTR-60020WIRE HARN VOLUME 2
304PTR-60024WIRE HARN IO
305PTR-60025WIRE HARN ANALOG
306PTR-60027WIRE HARN DC DRIVE
308600-7009-4000ASSY RGB CA D-SUB 15P 4000MM.
Page 117

FAN UNIT (STR-1070)

ITEM NO. PART NO. DESCRIPTION NOTE

1105-5340-01FAN BRKT LONG
101260-0011-02AXIAL FLOW FAN AC100V 50-60HZ

102 601-8543 RD

201000-P00312-WM SCR PH W/FS M3 X 12
Page 118

@ FAN UNIT OPPOSITE FLOW (STR-1070-01)

{(

SF Sy) SY)

ITEM NO. PART NO. DESCRIPTION NOTE

1105-5340-01FAN BRKT LONG
101260-0011-02AXIAL FLOW FAN ACI100V 50-60HZ
102601-8543FAN GUARD
201000-P00312-WM SCR PH W/FS M3 X 12
Page 119
  • AC UNIT (PTR-1060) (D-1/2)
Page 120
  • AC UNIT (PTR-1060)

ITEM NO.

RON PART NO.

FRI-1021 421-7468-01 421-8202 FRI-1022

214-0202 280-0417

509-5453-91-V-B 512-5046-10000 512-5046-5000 450-5126 450-5133 450-5134 450-5135 270-5081 310-5029-G20 601-0460

000-P00416-W 000-P00408-W 050-H00400 060-S00400 060-F00400 000-T00408-0B

FRI-60001 FRI-60002 FRI-60003 FRI-60004 FRI-60005 FRI-60006 PTR-60001 600-6972-0100

PTR-60101

008-T00412-0B (D-2/2)

DESCRIPTION NOTE

AC BRACKET STICKER C.P W/PIC STICKER EARTH MARK CONNECTOR LID

AC INLET PANEL TYPE TERMINAL BINDING POST BLACK TAIWAN NOT USED OTHERS SW ROCKER J8 V-B C.P 10000MA CE UL AC 110 ~120V AREA C.P 5000MA CE UL AC 220 ~ 240V AREA MAGNET CONTACT S-NIOCX AC 110V AREA MAGNET CONTACT S-NIOCX AC 200V_ AC 220V 60Hz AREA MAGNET CONTACT S-NIOCX AC 230V_ AC 220V S0Hz, AC240V AREA MAGNET CONTACT S-NIOCX AC 120V_ AC 120V AREA NOISE FILTER 20A SUMITUBE F G 20MM PLASTIC TIE BELT 100 MM

M SCR PH W/FS M4 X 16 M SCR PH W/FS M4 X 8 HEX NUT M4 SPR WSHR M4 FLT WSHR M4 M SCR TH BLK M4 X 8

WIRE HARN AC INLET A WIRE HARN AC INLET B WIRE HARN EARTH AC INLET WIRE HARN CP WIRE HARN MAIN SW. WIRE HARN FILTER IN WIRE HARN AC UNIT WIRE HARN EARTH IDS 0100MM TAIWAN NOT USED OTHERS WIRE HARN EARTH AC UNIT

TMP PRF SCR TH BLK M4 X 12

Page 121

(D-1/2)

  • ASSY PILLAR L (PTR-1070)
Page 122
  • ASSY PILLAR L (PTR-1070)

ITEM NO. PART NO.

1 PTR-1071 2 PTR-1072 3 PTR-1073 4 PTR-1074 5 PTR-1003 6 PTR-1004 7 PTR-1017

201 011-P03512 202 000-P00420-WB 203 000-T00412-0C 204 068-441616-0C (D-2/2)

DESCRIPTION NOTE

PILLAR BASE PILLAR COVER BRKT UPPER BRKT LOWER BRKT PILLAR COVER. END CAP END CAP BRKT LOWER

TAP SCR PH 3.5 X 12 M SCR PH W/FS BLK M4 X 20 M SCR TH CRM M4 X 12 FLT WSHR CRM 4.4-16 X 1.6

Page 123

ASSY PILLAR R (PTR-1075)

(D-1/2)

Page 124

ASSY PILLAR R (PTR-1075)

ITEM NO. PART NO.

1 PTR-1071 2 PTR-1072 3 PTR-1073 4 PTR-1074 5 PTR-1003 6 PTR-1004 7 PTR-1017

101 280-0419

201 011-P03512 202 000-P00420-WB 203 000-T00412-0C 204 068-441616-0C

301 PTR-60007 (D-2/2)

DESCRIPTION NOTE

PILLAR BASE PILLAR COVER BRKT UPPER BRKT LOWER BRKT PILLAR COVER, END CAP END CAP BRKT LOWER

HARNESS LUG

TAP SCR PH 3.5 X 12 M SCR PH W/FS BLK M4 X 20 M SCR TH CRM M4 X 12 FLT WSHR CRM 4.4-16 X 1.6

WIRE HARN AC PILLAR.

Page 125
  • ASSY BACK PANEL (PTR-1080)

ITEM NO. PART NO. DESCRIPTION NOTE

1PTR-1081BACK PANEL
2PTR-1082DESIGN PLATE
3PTR-1083DESIGN PILLAR.
4PTR-1084DESIGN SIDE PILLAR
5PTR-1085STICKER GRILLE PATTERN
201000-T00416-0CMSCR TH CRM M4 X 16
Page 126

ASSY COINCHUTE TOWER (PTR-1200) (D-1/2)

Page 127

ASSY COINCHUTE TOWER (PTR-1200) (D-2/2)

ITEM NO.

CHOIDARWNH os PART NO.

INY-1180 PTR-1201 APC-0301 APC-0302 DRT-0301X DP-1167 105-5171 253-5366 421-7501-02 440-WS0002XEG 421-6591-01

220-5237-92- ~ 220-5482-91- ~ 220-5643-01 220-5574 601-0460 280-5275-SR10 280-5009-01 310-5029-F20 601-6231-C045 220-5575

000-P00408-W 000-P00408-S 060-F00400 050-H00800 068-852216 060-S00800

PTR-60022 PTR-60023 600-6455-02 600-6972-0750 600-6972-0300 600-6972-0150 DESCRIPTION NOTE

SW UNIT TOWER COVER L COINCHUTE TOWER METER HOLE LID COIN METER BRKT TNG LKG CHUTE PLATE SINGLE CASH BOX STICKER 6.3V 0.15A STICKER W POWER OFF ENG. STICKER COIN METER

ASSY C.C 2DR ~ ASSY C.C 2DR ~ MAG CNTR DCSV 6P WH MZ-674-D04 CAM LOCK W/KEYS PLASTIC TIE BELT 100 MM CORD CLAMP SRI10 CORD CLAMP 21 SUMITUBE F F 20MM EDGING NEW TYPE CAM LOCK MASTER W/O KEY

M SCR PH W/FS M4 X 8 MSCR PH W/S M4 X8 FLT WSHR M4 HEX NUT M8 FLT WSRR 8.5-22 X 1.6 SPR WSHR M8

WIRE HARN VOLUME 3 WIRE HARN COINCHUTE TOWER WIRE HARN C.C DOOR SINGLE WIRE HARN EARTH IDS 0750MM WIRE HARN EARTH IDS 0300MM. WIRE HARN EARTH IDS 0150MM.

Page 128

(@) SW UNIT (INY-1180)

ITEM NO. PART NO.

1 INY-1181 2 421-8911

101 220-5179 102 509-5028 103 601-0042 104 310-5029-D20 105 601-0460

301 600-6609-32 302 600-6609-33 303 600-6609-34 DESCRIPTION NOTE

SW BRKT STICKER SW UNIT

VOL CONT B-5K OHM SW PB IM KNOB 22 MM SUMITUBE F D 20 MM PLASTIC TIE BELT 100 MM

WIRE HARN TEST & SERVICE WIRE HARN VOLUME A WIRE HARN VOLUME B

Page 129

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 130

ASSY MAIN BILLBOARD (PTR-1500) (D-2/2)

ITEM NO. PART NO.

PTR-1501 PTR-1502 PTR-1503 PTR-1504 PTR-1505 PTR-1506 PTR-1507 PTR-1508 PTR-1509 PTR-1510 PTR-1511 253-5457

421-7501-18

440-WS0143-EG 440-WS0027-EG 253-5460-01 PTR-1512 PTR-1513

390-6659-32EX

280-0419

000-T00418-0C 068-441616-0C 000-T00620-0B 000-T00410-0B 000-P00416-WB 000-T00416-0B 000-P00440-W

011-T03516 050-F00400 000-T00412-0C

PTR-60008 DESCRIPTION NOTE

MAIN BILLBOARD BASE MAIN BILLBOARD PLATE MAIN BILLBOARD COVER SASH BILL JOINT BRKT BILL WIRE COVER SASH LOWER SASH BRKT SIDE GUIDE L SIDE GUIDE R CUSHION FL HOLDER OTHERS Locally supplied. USA STICKER FL32W OTHERS Locally supplied. USA STICKER W POWER OFF WIDE ENG STICKER W HIGH TEMP WIDE ENG AIR VENT BLACK CUSHION UPPER CUSHION LOWER

ASSY FL32W EX W/CONN HIGH S CE OTHERS Locally supplied. USA HARNESS LUG

M SCR TH CRM M4 X 18 FLT WSHR CRM 4.4-16 X 1.6 M SCR TH BLK M6 X 20 M SCR TH M4 X 10 BLK M SCR PH W/FS BLK M4 X 16 M SCR TH BLK M4 X 16 M SCR PH W/FS M4 X 40 OTHERS Locally supplied. USA TAP SCR TH 3.5 X 16 FLG NUT M4 M SCR TH CRM M4 X 12

WIRE HARN AC BILLBOARD MAIN

Page 131

ASSY HIGH/LOW/BACK SHIFTER (PTR-2100) (D-1/2)

OE

Page 132

ASSY HIGH/LOW/BACK SHIFTER (PTR-2100) (D-2/2)

ITEM NO. PART NO.

SPG-2151 SPG-2152 SPG-2153 SPG-2154 SPG-2155 SPG-2156 SPG-2157 SPG-2158 SPG-2159 SPG-2160X SPG-2161 SPG-2162 SPG-2163 SPG-2164 PTR-2101 PTR-2102

100-5252 100-5193 100-5242 509-5636 601-0460 280-5306 280-5307

000-F00408 000-P00410-W 000-P00420-W 000-P00510-W 050-H00600 060-S00600 065-S010S0-Z FAS-000033 FAS-650008 FAS-450006

600-6445-45 600-6872 DESCRIPTION NOTE

SHIFT KNOB STOPPER RUBBER FRONT BASE SLIDE COVER SLIDE PLATE REAR BASE RUBBER BLOCK 45 RUBBER BLOCK 65 INSULATOR SHEET SHAFT CASE SHAFT BOLT CENTERING BLOCK RUBBER CASE ROLLER BOLT ROLLER SUPPORT GUIDE

BEARING ROLLER 25 GROMMET 11 BEARING FAI8 SW MICRO TYPE SS-5GL2T PLASTIC TIE BELT 100 MM SPACER FAI 6 X 30 SPACER FAI 8 X 55

M SCR FH M4 X8 M SCR PH W/FS M4 X 10 M SCR PH W/FS M4 X 20 M SCR PH W/FS MS X 10 HEX NUT M6 SPR WSHR M6 STP RING BLK OZ S10 MSCR PH W/FS M2.3 X 12 WAVE WSRHR 12.7-18.1 X 2.5 SPR PIN WAVE STN 5S X 45

WIRE HARN SHIFT MECHA WIRE HARN EARTH SHIFT MECHA

Page 133

8ZI1 WOT AIIALISNISMMM (w/1-@ (007@Z-DdS) ANVUI¥Y TADOV ASSV @

Page 134

ASSY ACCEL&BRAKE (SPG-2200) (D-2/2)

ITEM NO. PART NO.

SPG-2201 SPG-2202 SPG-2203 SPG-2204 SPG-2205 SPG-2206 SPG-2207 SPG-2208 SPG-2209 SPG-2210 SPG-2211 SPG-2212 SPG-2213 SPG-2214 SPG-2215 SPG-2216 SPG-2217 SPG-2219 SPG-2220 SPG-2221

100-5263 220-5484 601-7944 310-5029-F15 280-0419

028-A00304-P 020-000520-0Z 000-P00420 000-P00508-W 000-T00408-0C FAS-450005 000-P00405 FAS-000001 050-H00500 060-F00400

600-6840 DESCRIPTION NOTE

BASE ACCEL PEDAL BRAKE PEDAL. ACCEL SPRING BRAKE SPRING SHAFT ACCEL GEAR BRAKE GEAR NEUTRAL STOPPER, VR PLATE ACCEL VR PLATE BRAKE AMPL GEAR GEAR SHAFT STOPPER RUBBER CUSHION COVER VR COVER GEAR STAY WSHR NEUTRAL STOPPER D

BEARING 12 VOL CONT B-5K OHM GEAR 15 SUMITUBE F F 15MM HARNESS LUG

SET SCR HEX SKT CUP P M3 X 4 HEX SKT H CAP SCR BLK MS X 20 M SCR PH M4 X2 MSCR PH W/FS MS X 8 M SCR TH CRM M4 X 8 SPR PIN BLK OZ 6 X 10 M SCR PH M4 X5 M SCR TH CRM M3 X 6 HEX NUT M5 FLT WSHR M4

WIRE HARN ACCEL&BRAKE

Page 135

@1) ASSY HANDLE MECHA (PTR-2500)

(D-1/2)

8) RH

Page 136

@1) ASSY HANDLE MECHA (PTR-2500) (D-2/2)

ITEM NO.

ll PART NO.

PTR-2502 PTR-2503 PTR-2590 PTR-2505 PTR-2506 PTR-2515 PTR-2516 PTR-2550 PTR-2521 PTR-2523 PTR-2524 PTR-2528 SPG-2504 ASK-3502 ASK-3503 DYN-1270 SPG-2453 SPG-2454 PTR-2517 PTR-2518 PTR-2519 PTR-2531 PTR-2532-06 PTR-2532-08 PTR-2532-10 PTR-2532-12

350-5448-01 601-9173 100-5112 280-5009-01 280-5275-SR10 601-0460 220-5484 220-5373 310-5029-F20 601-8966 270-5117

020-000530-0Z 000-P00516-W 030-000625-S 060-F00600 000-P00414-W 028-C00416-P 065-S020S0-Z 065-S012S0-Z 030-000830-S 060-F00800 028-A00304-P

PTR-60029 PTR-60030 DESCRIPTION NOTE

HANDLE SHAFT STOPPER BLOCK ASSY TOP PLATE HANDLE MECHA STOPPER RING A STOPPER RING B MOTOR BASE BEARING BASE SENSOR UNIT COVER BRKT COLLAR A COLLAR B PULLEY 60 PULLEY 20 SSM MOTOR SPACER MOTOR COLLAR STOPPER KEY KEY 4X4X 40 MOTOR SHAFT COLLAR VOL BRKT GEAR 90 MO75 GEAR 30 MO75 STOPPER COLLAR SPACER PLATE06 SPACER PLATE08 SPACER PLATE10 SPACER PLATE12

SERVO MOTOR S00W NEW TIMING BELT BEARING 17 CORD CLAMP 21 CORD CLAMP SR10 PLASTIC TIE BELT 100 MM VOL CONT B-5K OHM VOL CONT B-5K SUMITUBE F F 20MM GEAR HOLDER FERRITE CORE TDK ZCAT3035-1330

HEX SKT H CAP SCR BLK 0Z MS X 30 M SCR PH W/FS MS X 16 HEX BLT W/S M6 X 25 FLT WSHR M6 M SCR PH W/FS M4 X 14 SET SCR CH CUP P M4 X 16 STP RING BLK OZ 820 STP RING BLK OZ S12 HEX BLT W/S M8 X 30 FLT WSHR M8 SET SCR HEX SKT CUP P M3 X 4

WIRE HARN HORN MAIN WIRE HARN HANDLE

Page 137

@5) SENSOR UNIT (PTR-2550)

LIGHT EMITTING SIDE (2P)

ITEM NO. PART NO. DESCRIPTION NOTE

1PTR-2551SENSOR BEKT
2PTR-2552GUIDE RING
101370-5226PHOTO SENSOR OMT-01DAMP NEW
102280-5275-SR10CORD CLAMP SR10
202000-P00312-WM SCR PH W/FS M3 X 12
Page 138

@) ASSY VR BUTTON START AND 1VIEW (PTR-2600)

ITEM NO. PART NO.

APC-2151X 171-6478B PTR-2601

212-5205-12 509-5560-Y 509-5561-S

(BLUE)

DESCRIPTION NOTE

VR BUTTON BRKT PC BD LIGHTING SWX5 STICKER VR BUTTON

CONN JST M 12P RTA PB SW WIL 6V IL Y PB SW WIL 6V SLS

Page 139

ASSY MAIN BD (PTR-4000)

2-6 30 3| Ory

(203\ NEW)

Oey WY

ITEM NO. PART NO.

1 PTR-4001 2 840-0023D-02 840-0023D-04 840-0023D-03 840-0023D-01 3 837-13844

101 280-5009-01 102 280-0419 103 601-0460

201 000-P00416-W 202 011-T00316 203 011-T03512 204 011-F00312

301 600-7141-050 302 600-7159-034 303 PTR-60017 304 PTR-60026 (204) NOTE: Make sure that there is no wiring, ete. a7 in the slash mark portions.

DESCRIPTION NOTE

MAIN BD BASE ASSY CASE NAO PTR EXP OTHERS ASSY CASE NAO PTR AUS AUSTRALIA ASSY CASE NAO PTR KOR KOREA ASSY CASE NAO PTR USA USA 1/0 CONTROL BD 2 FOR JVS FRI

CORD CLAMP 21 HARNESS LUG PLASTIC TIE BELT 100 MM

M SCR PH W/FS M4 X 16 TAP SCR TH 3 X 16 TAP SCR TH 3.5 X 12 TAP SCR FH 3 X 12

CABLE JVS TYPE A-B 050CM WIRE HARN JVS PWR 034CM WIRE HARN SOUND OUT WIRE HARN DC IO

Page 140

@5) ASSY CONTROL BD (PTR-4100)

  • (02)

e

Ulla

NOTE: Make sure that there is no wiring, etc. in the slash mark portions.

ITEM NO. PART NO.

PTR-4101

838-12912-01 838-13992 280-0419

011-P00325 011-T03516 O11-T03512

PTR-60035 PTR-60036

DESCRIPTION NOTE

CONTROL BD BASE

SERVO MOTOR DRIVE BD NEW DRIVE BD PTR HARNESS LUG

TAP SCR PH 3 X 25 TAP SCR TH 3.5 X 16 TAP SCR TH 3.5 X 12

WIRE HARN AC EXT WIRE HARN DC EXT

Page 141

ASSY AMP BD (PTR-4200) (D-1/2)

2-6 30

NOTE: Mak

Page 142

ASSY AMP BD (PTR-4200)

ITEM NO. PART NO.

1 PTR-4201 2 DRT-4502 3 421-7914-250630

101 601-10369 102 560-5419-V 103 838-13723 104 260-0011-02 105 601-8543 106 514-5086-6300 107 514-5084 108 280-5009-01 109 280-0419 110 400-5397-01 111 601-0460 112 310-5029-D20

201 000-P00312-W 202 050-F00300 203 000-P00416-W 204 011-P00325 205 011-F00312 206 O11-T03512 207 011-F00312

301 PTR-60010 302 PTR-60011 303 PTR-60012 304 PTR-60013 305 PTR-60014 306 PTR-60015 307 PTR-60016 (D-2/2)

DESCRIPTION NOTE

AMP BD BASE FAN MOTOR BRKT STICKER AC 250V 6.3A

STEREO PWR AMP 47 XFMR 100V 23V9.6A X 2 WOOFER AMP 50W X 2 AXIAL FLOW FAN AC100V 50-60HZ FAN GUARD FUSE S.B 6300MA 250V HBC CE FUSE HOLDER F-60B W/F-60 CORD CLAMP 21 HARNESS LUG SW REGU FOR JVS VA PLASTIC TIE BELT 100 MM SUMITUBE F D 20 MM

M SCR PH W/FS M3 X 12 FLG NUT M3 M SCR PH W/FS M4 X 16 TAP SCR PH 3 X 25 TAP SCR FH 3 X 12 TAP SCR TH 3.5 X 12 TAP SCR #1 FH 3 X 12

WIRE HARN WOOFER 1 WIRE HARN SPEAKER 1 WIRE HARN VOLUME | WIRE HARN AMP WIRE HARN SOUND MIX WIRE HARN AC AMP WIRE HARN SOUND IN

Page 143

@7) ASSY PWR SPLY (PTR-4300)

NOTE: Make sure that there is no wiring, etc. in the slash mark portions.
ITEM NO.PART NO.DESCRIPTIONNOTE
1PTR-4301PWR SPLY BASE
2PTR-4302CONN BRKT VL3P
3PTR-4303CONN BRKT UPI8P
101838-11856-ULCONNECT BD UL
103280-5009-01CORD CLAMP 21
104280-0419HARNESS LUG
105601-0460PLASTIC TIE BELT 100 MM
106560-5384XFMR 100-120V 100V 10A WBAC 110 ~120V AREA
560-5377PWR XFMR 200-240V 100V10A CEAC 220 ~240V AREA
202011-P00325TAP SCR PH 3 X 25
203011-F00310TAP SCR FH3 X 10
204011-T03512TAP SCR TH3.5 X 12
205000-P00616-WM SCR PH W/FS M6 X 16
301PTR-60002WIRE HARN AC 1
302PTR-60003WIRE HARN AC 2
303PTR-60004WIRE HARN AC 3
Page 144

ASSY TOP PLATE HANDLE MECHA (PTR-2590)

ITEM NO. PART NO. DESCRIPTION NOTE 1 PTR-2533 BASE HANDLE MECHA V2

2PTR-2534STOPPER BRKT V2
3PTR-2535ADDITIONAL STOPPER BRKT
4SPG-2109STOPPER RUBBER
101100-5052BEARING 6007ZZ
201050-F00500FLG NUT M5
202000-P00516-WM SCR PH W/FS MS X 16
203030-000616-SHEX BLT W/S M6 X 16
204060-F00600FLT WSHR M6
205050-H00600HEX NUT M6
206060-S00600SPR WSHR M6
Page 145
  • WIRE COLOR CODE TABLE

THE WI

moawp RE COLOR CODE is as follow:

PINK

SKY BLUE

BROWN

PURPLE

LIGHT GREEN

Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.

CnmrInkwnNne RED

BLUE

YELLOW

GREEN

WHITE

ORANGE

BLACK

GRAY

If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side numeral (see the above).

Note 1:
Note 2: If the right-hand side alphanumeric is not 0, that particular wire has a spiral color code. The left-hand side character shows the base color and the right-hand side one, the spiral color.

<Example> 51 oe. WHITE / RED

NOON ON

RED WHITE

The character following the wire color code indicates the size of the wire.

U: AWGI6

K: AWGI8

L: AWG20

‘None: AWG22

Page 146

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 147

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 (650) 632-7580 phone (650) 632-7594 fax