Kart Fury 27in
CART Fury Championship Racing (ver 1.00) (Midway Games, 2000) · Manual · 104 pages · 43 sections · original scan
SEPTEMBER 2000 G/DMIDWAY rena
Game Operations Manual for 27" Dedicated Video Game
CE
Manual Includes Operation & Adjustments Parts Information * Wiring Diagrams * Testing & Problem Diagnosis
The manufacturer intends that this game is to be operated for amusement purposes only and not in contravention of any federal, state or local law or regulation of the United States or any foreign country governing gaming devices. All operators of this game are responsible for its operation in accordance with such laws and regulations. The manufacturer's factory settings for this game may require adjustment in order to comply with laws applicable in an operator's specific jurisdiction. It is the operator's responsibility to determine whether adjustments are necessary and, if they are, to make the appropriate adjustments prior to operating the amusement game.
MIDWAY AMUSEMENT GAMES, LLC 3401 NORTH CALIFORNIA AVENUE CHICAGO, ILLINOIS 60618 USA http://www.midway.com
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
DECLARATION OF CONFORMITY
MIDWAY AMUSEMENT GAMES LLC
3401 N. CALIFORNIA AVE. CHICAGO, IL 60618 US.A.
WE, HEREBY DECLARE UNDER SOLE RESPONSIBILITY THAT
THE MODEL: "c.4.k.7. FURY" 27" 40290, 40390, 40490, 40790, 40990, 41090, 41190, 41290, 41390, 41490, 41890, 41990, 42090, 42190, 42290, 42390, 47190, 47290
TO WHICH THIS DECLARATION RELATES IS IN CONFORMITY WITH THE FOLLOWING EUROPEAN PRODUCT SAFETY DIRECTIVES:
ELECTROMAGNETIC COMPATIBILITY DIRECTIVE
(89/336/EEC AND AMENDMENTS 91/C162/08, 92/31/EEC,93/68/EEC)
ELECTRICAL EQUIPMENT DESIGNED FOR USE WITHIN
CERTAIN VOLTAGE LIMITS DIRECTIVE (73/336/EEC AND AMENDMENTS 88/C 168/02, 92/C210/01, 93/68/EEC, 94/C199/03, 95/C214/02)
AS IS VERIFIED BY COMPLIANCE WITH THE FOLLOWING STANDARDS:
EN55014: 1993 EN61000-4-2: 1995 EN61000-4-3: 1995 EN61000-4-4: 1995 EN61000-4-5: 1995 EN61000-4-6: 1995 EN61000-4-11: 1994 EN61000-3-2: 1995 EN61000-3-3: 1995 EN60335-1: 1995 IEC 60335-2-82: 1999
Date issued: MAY 19, 2000
oe BE
CORPORATE V.P. OF QUALITY
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
CABINET LINKING INSTRUCTIONS
CF To link two cabinets, use the crossover coupler included in the spare parts bag. Connect the factory installed linking cable to the coupler and follow the instructions for “Wiring Modifications and Software Setup” located below starting with step #7.
To link three or more cabinets, use a standard 10 base-T ethernet hub and follow all of the instructions for “Wiring Modifications and Software Setup” located below.
CABINET ARRAYS To create a Video Game Machine (VGM) Array, join the cabinets together. Each VGM comes equipped with the necessary hardware to connect cabinets and provide maximum stability. Hardware is located in the spare parts bag inside the cash box.
To join cabinets, remove the flat-head carriage bolts from the top and rear of adjacent cabinet sides. Position cabinets next to one another and adjust the leg levelers until all holes are aligned. Insert long carriage bolts through the holes in both cabinets, and then fasten in place with the nuts provided.
NETWORK CONSIDERATIONS Each VGM comes complete with a factory installed network cable. Optionally, a hub can be installed and located remotely to monitor network activity. Cables up to 328 ft., or 100 meters, in length may be used in conjunction with the hub provided they are Category 3 or higher, 100 ohm unshielded twisted pair communications grade wiring. Standard telephone cables are not sufficient for this application and should not be used.
Take care to protect exposed wiring from player foot traffic, cleaning crews, service personnel, etc. Use approved conduit or wire channels to support cables. Please note that modular connectors do not have strain relief.
Prevent linking cables from becoming damaged by avoiding sources of extreme heat or moisture, and high amounts of electrical energy like neon signs, fluorescent fixtures, two-way radios, cordless phones, power circuits, public address system wiring, etc.
Universal RJ-45 modular plugs are not numbered or coded in any way. Clearly label all network connections to avoid confusing network cables with computer or telephone circuits.
WIRING MODIFICATIONS AND SOFTWARE SETUP
- Place the linking hub inside the base of a cabinet nearest the center of the array. Remember that the crossover couplers supplied with the game are not used when creating an array using the hub. Crossover couplers are only used to link two cabinets.
- Unlock and remove the rear door from the cabinets selected to be part of the array. Inside the cabinet you will find a coil of linking cable with one end already attached to game electronics. Uncoil just enough of the cable to reach the hub, then recoil the rest of the cable and tie it in place. Repeat this procedure for each of the other cabinets. Do not reinstall the cabinet door(s) at this time.
- Route the free end of each cable out through the notch located in the rear door opening and plug into any jack on the rear panel of the linking hub. Route the free end of the AC adapter for the hub and plug it into the 9VAC jack on the front panel of the hub. Now all of the cables can be connected to the hub.
C.A.R.T. FURY v
Refer to the manufacturer's instructions in order to set the hub switches for LNK (link) and X (crossover) activity.
Fasten the hub to the bottom of the most central cabinet using a hook-and-loop type material. Orient the hub so that the indicator lights are visible and cable jacks are accessible.
Make sure excess cable is tied into a coil and that all cables are routed through the notch in the rear door. Connect the AC adapter for the hub and all line cords to AC power.
te CAUTION
Do not connect or disconnect any cable to the game electronics or hub with the power turned on. Circuit disruptions may damage the game and void the warranty.
Switch on power and closely observe the screen for each cabinet during start up. Each automatically enters ATTRACT MODE if no errors are found. Refer to Troubleshooting in the operation manual if errors are detected.
Unlock the coin door for each cabinet to access the operator control buttons inside coin vault. Press and hold the TEST button to enter the menu system.
-Verify linked games have compatible software versions. Newer versions may contain instructions previous versions do not, causing games to halt or reset at random.
Select ADJUSTMENTS from the Main Menu screen, then scroll to the ADDITIONAL ADJUSTMENTS MENU and press the Test button. Select GAME LINK NUMBER and press Test. Assign a linking number ranging from 1 to 4 to each game cabinet.
. Repeat these steps for each remaining game cabinet you wish to link.
. Close and lock the coin door, and reinstall and lock the rear door for each cabinet. Lower the leg levelers for each cabinet until the casters do not touch the floor and the cabinets are level. Lock the levelers in position by tightening the nuts provided.
vi Mipway AMUSEMENT GAMES, LLC
CHAPTER ONE
OPERATIONS
CHAPTER 1 OPERATION
SAFETY INSTRUCTIONS The following safety instructions apply to operators and service personnel. Read these instructions before servicing or preparing the Video Game Machine (VGM) for play. Other safety instructions appear throughout this manual.
DEFINITIONS OF SAFETY TERMS + DANGER indicates an imminent hazard. If you fail to avoid this hazard, it WILL cause death or serious injury. + WARNING indicates a potential hazard. If you fail to avoid this hazard, it COULD cause death or serious injury. + CAUTION indicates a potential hazard. If you fail to avoid this hazard, it MAY cause minor or moderate injury. CAUTION also alerts you about unsafe practices. + NOTE indicates information of special importance.
MIDWAY AMUSEMENT GAMES, LLC
CHAPTER 1 OPERATION
If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g., seizures or loss of awareness), immediately consult your physician before using any video games.
We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician.
CHAPTER 1 OPERATION
PRODUCT SPECIFICATIONS
Operating Requirements
Location Electrical Power Temperature Humidity
Domestic 120VAC @ 60Hz 4.0 Amps 32°F to 100°F Not to exceed 95% relative Foreign 230VAC @ 50Hz 2.0 Amps (0°C to 38°C) Japan 100VAC @ 50Hz 4.0 Amps
Cabinet Statistics
| Shipping Dimensions | Shipping Weight (Approx.) | Design Type |
| Width 30" (76.2 cm) | 350Lbs (158kg) Main Cabinet | Sit-In Dedicated Video Game |
| Depth 62" (157.4 cm) | 125Lbs (57kg) Seat Assy. | Machine with Steering Wheel |
Height 78" (198 cm) Feedback
Game Characteristics
| Player Variables | Operator Variables | Diagnostics |
| 1 to 4 players per VGM (with Linking) | Coinage, Play Mode, Difficulty, | Automatic Power-Up Self-Test |
| High Score Recognition | Volume, Audits, Statistics | Manual Multi-Level Menu System |
Suitable for All Ages (AAMA Certified)
Equipment Characteristics Video Display Monitor Medium Resolution RGB > 27" (68.6 cm) CRT
Audio System Digital Stereo 5” (12.7 cm) Coaxial Full Range Speakers
Currency Acceptors 2 Coin Mechanisms Dollar Bill Validator Ready Electronic Coin Acceptor Ready
PRODUCT CONFIGURATION
Stand Alone Video Game Machine Each VGM is ready to play right out of the box. Operators may use the menu screens in the game menu system to determine some player variables in advance or leave the choices up to the players.
Linked Video Game Machines Linking allows players to compete against each other on a single course. Operator menus are used the same way as in stand-alone VGMs. Crossover couplers and linking cables to connect two VGMs are factory installed. Use an optional 10 base-T ethernet hub to interconnect up to four VGMs.
4 MIDWAY AMUSEMENT GAMES, LLC.
CHAPTER 1 OPERATION
VIDEO GAME MACHINE ARRAY
SET-UP
- Remove all items from the shipping containers and set them aside. Remove all packing material. Inspect the exterior of the main cabinet, control cabinet and the seat pedestal for any damage.
- Remove the keys from the steering wheel. Unlock and open the rear door, and the coin and cash boxes. Electrical cords, mechanical components, and assorted spare parts are packed inside the cash box.
- Install one nut onto each leg leveler. Tilt as needed to locate four threaded holes under both the main cabinet and three holes under the pedestal. Install a leveler and nut into each hole. Do not tighten nuts at this time.
- The main cabinet is mounted on casters. Roll the cabinet to its intended location, maintaining clearance between the cabinet and walls, drapes, other games or obstructions.
CHAPTER 1 OPERATION
LOCATION OF CASTERS AND LEVELERS
- The pedestal assembly mounting rails are shipped bolted to the inside of the control cabinet. Remove all of the % -20 hex-head bolts used to fasten the rails inside the cabinet and set aside. Individually pull each rail out of the cabinet, flip it end for end, and reinsert it. See diagram for proper placement. Fasten the rail to the inside of the control cabinet with the bolts until finger tight. Do not tighten these bolts at this time, as some movement is required in the mounting rails to align holes with pedestal assembly
LOCATION OF PEDESTAL ASSEMBLY MOUNTING HOLES
6 Mipway AMUSEMENT GAMES, LLC
CHAPTER 1 OPERATION
- Roll the pedestal section near the cabinet, align the opening in the pedestal with the ends of the rails. Slide the pedestal forward onto extended mounting rails leaving enough space to attach the wiring harness. Mate each cable connector and press firmly to seat the contacts. Ensure no wires are pinched during pedestal attachment. Attach pedestal assembly using 1/4-20 tamper resistant screws and large flat washers provided in spare parts. A T27 wrench is included with the spare parts to tighten these screws firmly. Tighten the hex head bolts after the tamper resistant screws have been tightened.
- Lower and adjust each leg leveler until the pedestal section is stable and level. Adjust the levelers until the bottoms of all pieces are flush and parallel with each other. Inspect for binding or pinched wires. Insert and firmly tighten the remaining fasteners to attach the two pieces together as a single unit.
REAR DOOR HASP INSTALLATION
- An extra padlock may be installed to secure the rear door. A hasp is located in the spare parts bag. Remove the two lock bracket nuts from inside the cabinet, above the rear door opening. Slide the hasp bracket onto the bolts so that it protrudes from the hole in back of the cabinet, then reinstall nuts.
- Modify the lock plate at the top of the rear door. Remove the bolts and nuts from the lock plate, then rotate the plate so that the slot will be above the door. Reinstall the bolts and nuts and tighten firmly.
- Reinstall the rear door onto the cabinet and close it. Lock the rear door and remove the key. If required, install the extra padlock through the hasp at this time. Install the screws at the top and sides of the rear door and tighten snugly. Leave the remaining doors open at this time.
LINE CORD INSTALLATION
CHAPTER 1 OPERATION
11.
. Return to the Main Menu screen, and then choose EXIT. The game will automatically enter its “attract The power cord is packed in with the spare parts. Insert a portion of the line cord in the cord clamp leaving enough slack for the cord. Match the holes on the IEC plug with the prongs in the receptacle and push firmly to seat the line cord.
. Plug the game into a grounded (3-terminal) AC wall outlet. Switch on power to the game using the ON/ OFF switch located on the upper left top of the cabinet (when viewed from the player’s position). The game will power up and begin its self test. If no errors are found, the game will automatically enter the attract mode of operation (scenes and sounds from typical races, player’s scores, messages, etc.).
. Open the coin door. Press and hold the Begin Test button on the operator control switch panel to enter the menu system. Wait until the Main Menu screen appears on the monitor.
TYPICAL COIN DOOR SWITCH LOCATION
. Follow on-screen instructions to select Diagnostics, then choose SWITCH TEST. Follow the on-screen instructions to verify that each of the controls is operational. If no errors are found, the controls should function well.
. Return to the Diagnostics screen, then choose SPEAKER TEST. Follow the on-screen instructions to verify that each of the speakers is operational. If no errors are found, the audio should function well.
. Return to the Diagnostics screen, then choose WHEEL FEEDBACK TEST. Follow the on-screen instructions to verify the presence of steering resistance. If no errors are found, the aim will be good.
. Return to the Main Menu screen, then choose CONTROL CALIBRATION. Follow the on-screen instructions to set steering limits. If no errors are found, the controls will have the maximum accuracy.
mode of operation (scenes and sounds from typical races, player’s scores, messages, etc.).
. Insert currency or tokens and play a game. Change the volume and make any other adjustments. Close and lock all open doors. Tighten the leveler nuts and engage the caster locks.
MAINTENANCE + Viewing Glass It is not necessary to switch off power to the game to clean the glass. Apply a mild glass cleaner to a clean cloth or sponge and wipe the viewing glass. Do not apply the cleaner directly on the glass! Liquid could drip down into switch or control circuits and cause erratic game operation.
MIDWAY AMUSEMENT GAMES, LLC
CHAPTER 1 OPERATION
+ Player Controls Use plastic-safe, non-abrasive cleaners to avoid damage. Apply cleaner to a clean cloth or sponge and wipe the player controls. Do not apply the cleaner directly on the controls!
+ Cabinet and Seat Use plastic-safe, non-abrasive cleaners to avoid damage. Apply cleaner to a clean cloth or sponge and wipe the seat or cabinet. Do not apply cleaner directly on artwork or cabinet!
GAME FEATURES C.A.R.T. Fury: Championship Racing™ ships configured for one-player game play. Up to four cabinets may be linked to promote player competition.
C.A.R.T Fury™ is based on the Championship Auto Racing Teams, Inc. owned FedEx® Championship Series run yearly from March through October. CART races on road courses, temporary street circuits, oval tracks, and super speedways in five countries on four continents. The races are televised both domestically and around the world with a viewing audience of roughly over 57 million. Michael Andretti, Christian Fittipaldi, Juan Montoya and Jimmy Vasser are but a few of the drivers involved in the CART circuit.
C.A.R.T Fury: Championship Racing™ features a total of 12 tracks to choose from. There are 8 actual CART courses, as well as 4 fantasy courses. Each course is packed with highly realistic scenery, immersive physics and the most amazing wrecks and crashes. Additionally, players can opt to play a full 12-race season, with points awarded for winning positions!
STARTING UP Each time power is switched on or restored to the game machine, the system enters Start-up Tests. The software revision level is shown at the top of the screen. A status screen to report on network activity will appear for about ten seconds. This screen is used to verify and troubleshoot connections on an array of cabinets.
The system enters Attract Mode once it passes all power-up tests. The Attract Mode screen will cycle endlessly and display a variety of scenes and sounds from a typical race on any given track. The system does not exit Attract Mode until the desired amount of coins or tokens is inserted and game play commences.
GAME RULES AND OBJECTIVES The game is configured for one-player game play, but up to four cabinets may be linked at one time to promote multiple player competition. To enter Game Mode, individual player(s) must insert the required amount of currency or tokens, press the Start button, and select a car and track. The main objective of the game is to earn top ranking against other drivers.
PLAYER CONTROLS + Start Button is used to begin game play or to select certain features before a race.
+ Boost Button, located on either side of the steering wheel, provides extra boost while passing other cars during competition
+ View 1 Button shows the view from the driver’s seat inside the vehicle. This is a normal driver view.
+ View 2 Button shows the view from directly above. The player can see the front end of the vehicle.
CHAPTER 1 OPERATION
+ View 3 Button shows an aerial view of the vehicle. This is what a helicopter camera would see.
+ Pedals, for both gas and brakes, are used to control vehicle speed.
+ Seat Position Adjuster may be changed at any time, even during competition. Pull the adjustment lever to the left while seated then slide the seat forward or backward. Release the lever to lock the seat into position.
GAME OPERATION Access to the menu system for statistics, adjustments, and testing is secured by a keyed lock on the coinbox to prevent tampering. When the menu system is entered, on screen messages guide the operator through tasks.
CABINET SWITCHES + ON/OFF SWITCH is located on the top right side of the cabinet.
+ REMOTE MONITOR ADJUSTMENT knobs are located inside coin vault. Use the monitor test screens with these controls to adjust the video image size, brightness, contrast, etc.
+ SLAM TILT SWITCH, located on the inside of the coin door opening near the lock, detects any forceful vibrations against coin door. This switch prevents awarding of free games due to pounding on coin door.
CONTROL BUTTONS + TEST BUTTON activates the game Menu System. Press the Test button to access the Main Menu and select individual diagnostics, audits, utilities, etc.
+ VOLUME UP BUTTON is used to move up through the menu selections or adjustment items, as well as to increase volume level in game play. Activation of this button is accompanied by a distinct sound.
+ VOLUME-DOWN BUTTON is used to move down through the menu selections or adjustment items, as well as to decrease volume level in game play. Activation of this button is accompanied by a distinct sound.
+ SERVICE CREDIT BUTTON is used to allot credits without affecting the game's bookkeeping total. This button is also used to exit a menu selection or to return to the main menu.
10 Mipway AMUSEMENT GAMES, LLC
CHAPTER TWO
ADJUSTMENT, DIAGNOSTIC & AUDIT MENUS
CHAPTER 2 DIAGNOSTICS
ADJUSTMENT, DIAGNOSTIC & AUDIT MENUS
MENU SYSTEM
WHAT IS THE MENU SYSTEM? The game’s Menu System is a series of auditing, game adjustments and diagnostic screens. You can easily access and apply these screens to optimize game performance. For instance...
+ Use game audit screens to assess game performance. + Use adjustment screens to help you customize game performance. For example, you can restore factory default game settings. You can also calibrate player controls for player accuracy. + Use diagnostic screens to verify proper equipment operation.
ACCESSING THE MENU SYSTEM Open the coin door. Locate and press the TEST MODE switch. The game system will exit game Attract Mode and enter Diagnostic Mode. The system runs a brief self-test, and then displays the Main Menu. The Main Menu is the opening screen of the Menu System.
Game audits, adjustments and diagnostics are line items on the Main Menu. Selecting an item opens its submenu. Every submenu presents various options that you may act upon.
C.A.R.T. MAIN MENU
DIAGNOSTICS AUDITS ADJUSTMENTS VOLUME LEVEL CONTROL CALIBRATION UTILITIES EXIT
TYPICAL MAIN MENU SCREEN
MENU LAYOUT Observe that each menu screen basically uses the same layout. The game ID, Serial Number, and Date of Manufacture will appear on most of the menu screens. These numbers will be helpful to factory personnel when referring to your game for parts or service.
+ The block at the top of each screen displays the current menu title. + Data, such as menu items and video reports, etc., appears in the center of the screen. + Messages, for example explanations and active control functions, etc., appear at the bottom of the screen.
MENU NAVIGATION TOOLS, Use the operator control buttons located inside the coin door to navigate menus. Press the Volume Up or Volume Down buttons to scroll through the menu options.
Notice the options sequentially become highlighted. Press the Test button to select a highlighted option and access the next menu level. NOTE: Only one highlighted option can be selected at a time.
To return to play mode, select Exit and press the Test button while in the Main Menu screen.
2 MIDWAY AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Diagnostics Menu
DIAGNOSTIC MENU To verify the condition of the electrical and electronic hardware in the game, select Diagnostics Menu at the Main Menu. Diagnostic tests assist you in checking and adjusting the game’s major systems. It is
DIAGNOSTICS
Use the Volume Up or Volume Down button to highlight the desired Diagnostic Menu option and press the Test button to enter.
Monitor Setup
MONITOR SET-UP To verify color clarity of the monitor, select MONITOR SETUP at the Main Menu.
Use the Volume Up or Volume Down button to highlight the desired monitor setting and press the Test button. Watch for the following results on-screen during this test.
MONITOR SET-UP
wo
CHAPTER 2 DIAGNOSTICS
Monitor Setup, continued COLOR BARS. Observe 4 color bars in different shades appear on-screen as aids in adjusting the green, blue, and red color levels. Each color should appear sharp and clear. Check video brightness and contrast.
The CROSSHATCH PATTERNS test fills the screen with a series of dots within a grid. Observe the dots are perfectly round and that both the grid and dots are clear. Inspect monitor convergence, linearity, and screen size.
The single color screens, RED SCREEN, BLUE SCREEN, GREEN SCREEN, etc., fills the screen with a single color to be observed for complete saturation and clarity.
If any of the tests show a need for CRT adjustment, use the proper knobs on the Monitor Controls board.
System Information
SYSTEM INFORMATION To verify game serial number and date code select System Information at the Main Menu.
SYSTEM INFORMATION
TYPICAL SYSTEM INFORMATION SCREEN
Use the Start button or Test button to exit this menu screen.
Sound Subsystem Test
SOUND SUBSYSTEM TEST To Verify proper operation of the sound electronics select Sound Subsystem Test at the Main Menu. Observe the following information on the screen.
4 Mipway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Sound Subsystem Test, continued
SOUND SUBSYSTEM TEST
Use the Start button or Test button to exit this menu screen.
Disk Tests Menu
DISK TESTS MENU To verify hard disk drive information and perform tests, select Disk Test at the Main Menu. Use the Volume Up and Volume Down buttons to highlight an item. Use the Test or Start button to select an item.
DISK TESTS
+ Select DISK INFORMATION to learn information about the IDE disk drive.
+ Select SEQUENTIAL READ to view the sequential sector read without the cache.
+ Select SEQUENTIAL CACHE READ to view the sequential sector read with the cache.
+ Select RANDOM READ to view the random sector read without the cache.
+ Select RANDOM CACHE READ to view the random sector read with the cache.
+ Select DATA INTEGRITY TEST to perform a disk data integrity test.
+ Select FILE SYSTEM CHECK to test the integrity of files on the disk.
+ Select SURFACE SCAN to perform a scan of the disk’s surface.
CHAPTER 2 DIAGNOSTICS
Switch Tests
SWITCH TESTS To verify proper operation of switch and button inputs in the game, select Switch Test at the Main Menu.
SWITCH TESTS
Use the Volume Up or Volume Down button to highlight the Switch Test option and press the Test button to access it.
Press any switch on the control panel or coin door to cause the corresponding indicator on the screen to illuminate. Each illuminated square represents one completed switch circuit.
DIP Switch Test
DIP SWITCH TEST To verify the functionality of both 8-position DIP switches on the CPU Board, select DIP SWITCH TEST at the Main Menu. Observe immediate on-screen results by changing the setting on a switch.
Use the Volume Up or Volume Down button to highlight the DIP Switch Test option and press the Test button to access it. The current settings appear on-screen.
Consult the table on the next page to determine if changes are required. The default switch positions are all OFF for standard operation.
A vertical bar next to the switch position column indicates a common switch function.
6 Mipway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Main Menu Diagnostic Menu, continued DIP Switch Test, continued
DIP SWITCH TEST
DIP SWITCH U13 DIP SWITCH U12
8 OFF UNUSED 8 OFF GAME MODE 7 OFF UNUSED 7 OFF UNUSED 6 OFF USA 1 6 OFF BRAKE ENABLED 5 OFF USA 1 5 OFF UNUSED 4 OFF USA 13... 4 OFF UNUSED 3 OFF USA 13... 3 OFF UNUSED 2 OFF USA 13... 2 OFF UNUSED 1 OFF DIP COINAGE 1 OFF UNUSED
PRESS ANY BUTTON TO EXIT TYPICAL DIP SWITCH SCREEN
Coinage Setting Table for DIP Switch U13 (Factory default settings in boldface type) FUNCTION Swi | Sw2 | Sw3 | SW4 ] SWS | SWée | SW7 | SWS DIP COINAGE OFF CMOS COINAGE ON USA 13 GERI FR ECA1 UK1 ECA OFF | off | OFF USA 11 GER2 FR ECA2 UK2 ECA ON | Orr | OFF USA 10 GER3 FR ECA3 UK3 ECA OFF | on | OFF USA 1 GER4 FR ECAd UK4 ON | On | OFF USA DC8 GERS FR ECA5 UK5 OFF | GFF | ON USA DC6 GER ECA1 FR ECA6 UK6 ECA ON | Orr | ON USA DC5 GER ECA2FR ECA7 UK7 ECA OFF | on | ON USA DC1 GER ECA3 FR ECA8 ON | On | ON FREE PLAY (UK) On | ON | ON USA OFF | OFF FRANCE ON | OFF GERMANY OFF | ON UK* ON | ON UNUSED OFF ON UNUSED OFF ON
DIP SWITCH SETTING FOR COINAGE There are many ways to select the type and quantity of currency recognized by the game machine.
- The most common coin combinations for several countries are pre-programmed and may be selected from the table when Standard Pricing is activated (see Game Adjustments).
- DIP Switch settings may be changed with the power switched on. Set any switch and then observe the screen to verify that the desired selection is enabled. NOTE: If CMOS Coin Settings are active, switch settings for an individual Country will have no effect.
- Some European countries may accept currency used in other countries. The most popular coinage settings are listed beneath in the Pricing Table.
CHAPTER 2 DIAGNOSTICS
Main Menu
Diagnostic Menu, continued
DIP Switch Test, continued
Setting Table for DIP Switch U12 (Factory default settings in boldface type)
FUNCTION swi sw2 SW3 SW4 SW5 SW6 SW7_~ SW8
UNUSED OFF ON
UNUSED OFF ON
UNUSED OFF ON
UNUSED OFF ON
UNUSED OFF ON
BRAKE ENABLED OFF BRAKE DISABLED ON
UNUSED OFF ON
GAME MODE OFF TEST MODE ON
Main Menu
Diagnostic Menu, continued
Lamp and LED Tests
LAMP & LED TESTS To verify the proper operation of lamps and LED’s, select the LAMP & LED TESTS at the Main Menu.
Use the Volume Up or Volume Down button to highlight Lamp & LED Test and press the Test button. During the test observe the selected lamp(s) switches turn on or off when the corresponding selection is made.
8 MIDWAY AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Lamp Tests
LAMP TESTS To detect intermittent or faulty incandescent bulbs, select LAMP TEST at the Main Menu. This test ensures that the incandescent bulbs critical to game operation function properly.
LAMP TEST
Use the Volume Up or Volume Down button to highlight Lamp Test and press the Test button. During the test observe the Lamp(s) turn ON according to the option selected.
LED Tests
LED TESTS To verify that the LED’s function properly, select LED TEST at the Main Menu. This test allows you to control and test the illumination of the LED's located on the dash PCB.
LED TESTS
Use the Volume Up or Volume Down button to highlight LED Test and press the Test button. During the test observe the LED’s turn ON.
©
CHAPTER 2 DIAGNOSTICS
Wheel Feedback Test
WHEEL FEEDBACK TEST To verify the proper directional movement of the steering wheel, select Wheel Feedback Test at the Main Menu. Make sure hands and other objects are clear of the steering wheel when this test is selected because the steering wheel automatically rotates on its own.
Use the Volume Up or Volume Down button to highlight Wheel Feedback Test and press the Test button.
WHEEL FEEDBACK TEST
Observe and follow the on-screen instructions for conducting the test. During the test observe the steering wheel is turned automatically. Upon completion of the test, the message TEST COMPLETE appears onscreen. Press the Test or Start button to exit test once this message appears.
Control Test
CONTROL TEST To verify the presence of steering wheel control, gas pedal and brake pedal control, select Control Test at the Main Menu.
Use the Volume Up or Volume Down button to highlight Control Test and press the Test button.
During the test observe the selected control input or switch turns on or off when the corresponding selection is made. NOTE: Information regarding the brake pedal will not appear if DIP 6 on DIP Switch U12 is ON.
CONTROL TEST
10 Mipway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Speaker Test
SPEAKER TEST To verify proper operation of the sound components, select Speaker Test at the Main Menu. This test allows you to access and listen to the sound emitted from the speakers used in the game.
SPEAKER TEST
Use the Volume Up or Volume Down button to highlight the Speaker Test option and press the Test button. Use the Volume Up or Volume Down button to highlight an option within the test itself and press the Test button to activate the test option.
Link Test
LINK TEST To verify communications between the game machine and others connected to it, select Link Test at the Main Menu.
LINK TEST
Use the Volume Up or Volume Down button to highlight Link Test and press the Test button. This test runs automatically and will display results on-screen.
Press the Test button to exit from this menu screen.
CHAPTER 2 DIAGNOSTICS
Audits Menu
AUDITS MENU Press the Volume Up or Volume Down button to highlight Game Audits in the Main Menu and press the Test button. To move between pages in an Audit Table, press the View 1/Volume Up or View 2/Volume Down button. Press the Test or Start button to return to the Main Menu from this screen.
AUDITS
The Game Audits Table displays the play statistics. The left side of the table names the Audit item; the right side shows the amount of play. Record these statistics before any service or repairs are done.
Coin Audits
COIN AUDITS To keep track of the number of coins collected, press the Volume Up or Volume Down button to highlight Coin Audits in the Main Menu and press the Test button.
To move between pages in an Audit Table, press the View 1/Volume Up or View 2/Volume Down button. Press the Test or Start button to return to the Main Menu from this screen.
COIN AUDITS
AUDIT TABLE, PAGE 1
12 Mipway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Credits Audits
CREDITS AUDITS To keep track of the available number of credits, press the Volume Up or Volume Down button to highlight Credits Audits in the Main Menu and press the Test button. To move between pages in an Audit Table, press the View 1/Volume Up or View 2/Volume Down button.
CREDITS AUDITS
AUDIT TABLE, PAGE 1
General Game Audits
GENERAL GAME AUDITS To keep track of the game play statistics, press the Volume Up or Volume Down button to highlight General Game Audits in the Main Menu and press the Test button.
To move between pages in an Audit Table, press the View 1/Volume Up or View 2/Volume Down button.
GENERAL GAME AUDITS.
AUDIT TABLE, PAGE 1
CHAPTER 2 DIAGNOSTICS
Player Selection Audits
PLAYER SELECTION AUDITS, To keep track of game play choices like race venue, character selection, car selection and handling options, press the Volume Up or Volume Down button to highlight Player Selection Audits in the Main Menu and press the Test button.
To move between pages in an Audit Table, press the View 1/Volume Up or View 2/Volume Down button.
PLAYER SELECTION AUDITS
PLAYER SELECTION AUDITS
14 Mipway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Player Selection Audits, continued
PLAYER SELECTION AUDITS
Exception Dump Audit
EXCEPTION DUMP AUDIT To display cause, PC, and register audits, press the Volume Up or Volume Down button to highlight Exception Dump Audits in the Main Menu and press the Test button.
To move between pages in an Audit Table, press the View 1/Volume Up or View 2/Volume Down button.
EXCEPTION DUMP AUDITS
Track Audits
TRACK AUDITS To view track statistics, press the Volume Up or Volume Down button to highlight Track Audits in the Main Menu and press the Test button.
To move between pages in an Audit Table, press the View 1/Volume Up or View 2/Volume Down button.
CHAPTER 2 DIAGNOSTICS
Track Audits, continued
TRACK AUDITS
SAMPLE TRACK AUDITS PAGE
Clear Audits
CLEAR AUDITS Clear Audits displays an assortment of audit clearing options. One or all audit tables can be cleared using this audit screen.
You may wish to record some or all of the statistics before clearing an audit table, due to any reason, for future reference.
CLEAR AUDITS
16 Mipway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Main Menu
Audits, continued Clear Audits, continued
Each of the menu options beneath Clear Audits presents a confirmation box, like the one shown below, which offers you the choice of accepting or declining the selected action.
Press the Volume Up or Volume Down button to highlight the desired response and press the Test button. Aconfirmation box will appear to confirm that the desired action has been carried out.
ARE YOU SURE YOU WANT TO CLEAR CREDITS?
YES NO
TYPICAL CLEAR AUDITS BOX
Main Menu
Adjustments Menu
ADJUSTMENTS MENU To optimize game performance and earnings or to change the look or sound of the game, select the Adjustment Menu at the Main Menu.
The Attract Mode features, Game Pricing and Game Difficulty may also be customized. Free races may be awarded to encourage players. Free game player incentives may reduce earnings. NOTE: Individual Game Adjustments are explained in more detail on the following pages.
Press the Volume Up or Volume Down button to highlight the desired Adjustments Menu option on the Main Menu and press the Test button. Use these screens to optimize game performance and earnings.
ADJUSTMENT MENU
PRICING FREE PLAY ATTRACT SOUND ADDITIONAL ADJUSTMENTS FULL FACTORY RESTORE EXIT
The Adjustments Menu offers several options. Press the Volume Up or Volume Down button to highlight an option and press the Test button. Each time an option on the menu is activated you are provided with multiple setting choices.
Use the Volume Up or Volume Down button to change the current value setting and observe a confirmation box as shown appears.
CHAPTER 2 DIAGNOSTICS
Adjustments Menu, continued
ARE YOU SURE YOU WANT TO SELECT THIS PRICING?
TYPICAL CONFIRMATION BOX
Press the Volume Up or Volume Down button to select YES or NO, then press the Test button to lock in the setting. Selecting NO cancels any changes values and returns the previous values to memory.
Pricing
PRICING MENU Use the Pricing Menu to specify pricing settings other than the ones listed in the Pricing Table.
Pricing can also be used to select the amount of credits required to start a game and the amount of credits required to continue a game. This option is adjusted from the Dip Switch Settings.
PRICING MENU
18 Mipway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Pricing Table
Use the Pricing Table illustrated below as a guide to select and/or verify the desired coin credit setting(s).
| NAME | START | |CONTINUE | |CREDITS/COIN | COIN1 | |COIN2 | |COIN3 | |COIN4 | /|BILL |
| ANTILLES | 2 | 2 | 1/25¢, 4/1G | .25¢ | 1G | |||
| AUSTRALIA 1 | 2 | E- | 1/3X20¢, 2/$1.00 | 20¢ | $1.00 | |||
| AUSTRALIA 2 | 1 | 1 | 1/5X20¢, 1/$1.00 | 20¢ | $1.00 | |||
| AUSTRIA 1 | 2 | 2 | 1/5Sch, 2/10Sch | 5 Sch | 10 Sch | |||
| AUSTRIA 2 | # | 2 | 1/2X5Sch, 3/2X10Sch | 5 Sch | 10 Sch | |||
| BELGIUM 1 | 2 | 2 | 1/20BF | 20BF | 20BF | |||
| BELGIUM 2 | £ | 2 | 3/20BF | 20BF | 20BF | |||
| BELGIUM 3 | 2 | 2 | 2/20BF | 20BF | 20BF | |||
| BELGIUM ECA | 2 | 2 | 1/20BF | SBF | 20BF | 50BF | ||
| CANADA 1 | 2 | 2 | 1/2x25¢,3/$1 | 25¢ | 25¢ | |||
| CANADA 2 | = | 2 | 1/2x25¢,3/$1 | 25¢ | $1.00 | |||
| CANADA 3 | 2 | 2 | 3/ $1.00, 6 / $2.00 | $1.00 | $2.00 | |||
| CANADA ECA | 2 | 2 | 1/2x25¢,3/$1 | 25¢ | $1.00 | $2.00 | ||
| DENMARK | @ | 2 | 3/5Dkr, 7/10DKr | 5DKr | 10DKr | |||
| FINLAND: | 2 | 2 | 1/1Fmk | 1Fmk | 5Fmk | |||
| FRANCE 1 | 2 | 2 | 2/5Fr, 5/10Fr | SFr | 10Fr | |||
| FRANCE 2 | 2 | 1 | 2/5Fr, 4/10Fr | SFr | 10Fr | |||
| FRANCE 3 | 2 | 1 | 1/5Fr, 3/10Fr | SFr | 10Fr | |||
| FRANCE 4 | ie | 1 | 1/5Fr, 2/10Fr | SFr | 10Fr | |||
| FRANCE 5 | 2 | 1 | |2/5Fr, 5/10Fr, 11/2 X 10Fr | SFr | 10Fr | |||
| FRANCE 6 | 2 | 1 | 2/5Fr, 4/10Fr, 9/2 X 10Fr | SFr | 10Fr | |||
| FRANCE 7 | 2 | 1 | SFr, 3/10Fr, 7/2 X 10Fr | SFr | 10Fr | |||
| FRANCE 8 | ee | 1 | SFr, 2/10Fr, 5/2 X 10Fr | SFr | 10Fr | |||
| FRANCE 9 | z. | 1 | 1/3 X 1 Fr, 2/5Fr | (Fr | SFr | |||
| FRANCE 10 | 2 | 1 | 1/2 X 1Fr, 3/SFr | (Fr | SFr | |||
| FRANCE 11 | 2 | 1 | 1/3 X 1Fr, 2/5Fr, 5/2 X SFr | (Fr | SFr | |||
| FRANCE 12 | 2 | 1 | 1/2 X 1Fr, 3/5Fr, 7/2 X SFr | (Fr | SFr | |||
| FRANCE ECA 1 | 1 | 1 | 2/5Fr, 5/10Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 2 | 1 | 1 | 2/5Fr, 4/10Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 3 | 1 | 1 | 4/5Fr, 3/10Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 4 | 1 | 1 | 1/5Fr, 2/10Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 5 | 1 | 1 | 2/5Fr, S/10Fr, 11/2 X 10Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 6 | 1 | 1 | 2/5Fr, 4/10Fr, 9/2 X 10Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 7 | 1 | 1 | SFr, 3/10Fr, 7/2 X 10Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 8 | 1 | 1 | /5Fr, 2/10Fr, 5/2 X 10Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 9 | 1 | 1 | 1/3 X 1Fr, 2/5Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 10 | 1 | 1 | 1/2 X 1Fr, 3/SFr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 11 | 1 | 1 | 1/3 X 1Fr, 2/5Fr, S/10Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 12 | 1 | 1 | 1/3 X 1Fr, 3/5Fr, 7/1 0Fr | (Fr | SFr | 10Fr | 20Fr | |
| FRANCE ECA 13 | 1 | 1 | 4/1 0F r, 2/20Fr, 4/30Fr | (Fr | SFr | 10Fr | 20Fr | |
| FREE PLAY | od | ” | None | None | None | None | None | |
| GERMANY 1 | 2 | 2 | 1/1DM, 6/5DM | 1DM | 5DM | |||
| GERMANY 2 | e | 1 | 1/1DM, 7/5DM | 1DM | 5DM | |||
| GERMANY 3 | 2 | 1 | 1/1DM, 8/5DM | 1DM | 5DM | |||
| GERMANY 4 | 2 | 1 | 1/1DM, 5/5DM | 1DM | 5DM | |||
| GERMANY 5 | 2 | 1 | 1/1DM, 6/5DM | 1DM | 5DM | |||
| GERMANY ECA 1 | 2z | 2 | 1/1DM, 2/2DM, 6/5DM | 1DM | 2DM | 5DM |
CHAPTER 2 DIAGNOSTICS
NAME START |CONTINUE [CREDITS/COIN COIN1 |COIN2 |COIN3 |COIN4 JBILL GERMANY ECA2 [2 1 1/1DM, 2/2DM, 6/5DM 1DM 20M ‘SDM
GERMANY ECA3 [1 1 1/1DM, 2/2DM, 6/5DM 1DM 20M 5DM
HUNGARY 2 2 /2X10Ft, 3/2X20Ft 10Ft 20Ft
| ITALY | 2 2 | 1/S00LIt | ‘SOOLIt SOOLIt |
| JAPAN 1 | 2 2 | 1/100Yen | 700 Yen [100 Yen |
| JAPAN 2 2 2 | 2/00Yen | 100 Yen | 400 Yen | |
| JAPAN 3, 1 1 | 1/100Yen | 100 100 | |
| JAPAN 4 1 1 | 2/00Yen | 100 100 | |
| JAPAN 5 1 1 | 4/o0Yen | 100 100 | |
| JAPAN 6 1 1 | 1/2X100Yen | 100 100 |
NETHERLANDS 2 2 1/1HFI, 3/2.5HFI THI 2.5HFI
| NEW ZEALAND 1 [1 1 | 181 | a $2 |
| NEW ZEALAND 2 |1 1 | 2181 | $1 $2 |
NORWAY 2 2 S/SNKr, 6/10NKr ‘SNKr 10NKr
| ‘SPAIN 1 | 2 2 | 1/100Pta, 6/500Pta 1ooPta —_[500Pta |
| SPAIN 2 | 2 2 | 1/100Pta, 5/500Pta 100Pta_ | 500Pta |
‘SWEDEN 2 2 1/3X18Kr, 2/5SKr 18Kr 5SKr
| SWITZERLAND1 — [2 2 | 1/1 SFr, 6/SSFr | 1SFr 5SFr |
| SWITZERLAND 2 = |2 2 | 1/1 SFr, 7/5SFr | 1SFr SFr |
| SWITZERLAND3 = |2 2 | 1/1 SFr, 8/5SFr | 1SFr 5SFr |
| UKECA 1 1 1 | 1/50p, 3/81.00 | £1.00 50p 20p 10p £2.00 |
| UK ECA 2 1 1 | 1/50p, 2/81.00 | £1.00 50p 20p 10p £2.00 |
UK ECA3 1 1 1/30p, 2/50p, 5/£1.00 £1.00 50p 20p 10p £2.00
| UK 4 | 1 1 | 1/50p, 3/£1.00 | £1.00 50p |
| UKS | 1 1 | 1/50p, 2/81.00 | £1.00 50p |
UK ECA6 1 1 1/30p, 2/50p, 4/£1.00 £1.00 50p 20p 10p £2.00
| UK ECA7 1 1 | 3/£1.00 | £1.00 50p 20p 10p £2.00 |
UK ECA8 1 1 1/50p, 2/81.00, 4/£2.00 £1.00 50p 20p 10p £2.00
| usa | 2 2 | 1/256 | 25¢ 25¢ | $1.00 |
| usa2 | 2 1 | 1/25¢ | 25¢ 25¢ | $1.00 |
| usas | 1 1 | 1/25¢ | 25¢ 25¢ | $1.00 |
| usa4 | 1 1 | 1/50¢, 3/$1.00 | 25¢ 25¢ | $1.00 |
| UsAS | 2 1 | 1/50¢, 4/$1.00 | 25¢ 25¢ | $1.00 |
| usa6 | 1 1 | 1150¢ | 25¢ 25¢ | $1.00 |
| usa7 | 1 1 | 1/50¢, 3/$1.00 | 25¢ 25¢ | $1.00 |
| usas | 2 2 | 1/50¢, 4/$1.00 | 25¢ 25¢ | $1.00 |
| usag | 3 2 | 1/25¢, 4/$1.00 | 25¢ 25¢ | $1.00 |
| usa10 | 3 3 | 1/25¢, 4/$1.00 | 25¢ 25¢ | $1.00 |
| usa1t | 4 2 | 1/25¢, 4/$1.00 | 25¢ 25¢ | $1.00 |
| usa12 | 4 3 | 1/25¢, 4/$1.00 | 25¢ 25¢ | $1.00 |
| usa13 | 4 4 | 1/25¢, 4/$1.00 | 25¢ 25¢ | $1.00 |
| USA ECA 2 2 | 1/25¢, 4/$1.00 | $1.00 25¢ 10¢ 05¢ $1.00 | ||
| USADC1 2 2 | 1/256 | 25¢ $1.00 | $1.00 | |
| USA DC 2 2 1 | 1/25¢ | 25¢ $1.00 | $1.00 | |
| USA DC3 1 1 | 1/25¢ | 25¢ $1.00 | $1.00 | |
| USA DC 4 3 2 | 1/25¢, 4/$1.00 | 25¢ $1.00 | $1.00 | |
| USA DC5 3 3 | 1/25¢, 4/$1.00 | 25¢ $1.00 | $1.00 | |
| USA DC6 4 2 | 1/25¢, 4/$1.00 | 25¢ $1.00 | $1.00 | |
| USA DC7 4 3 | 1/25¢, 4/$1.00 | 25¢ $1.00 | $1.00 | |
| USA DC8 4 4 | 1/25¢, 4/$1.00 | 25¢ $1.00 | $1.00 |
20 Mibway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Free Play
FREE PLAY This option selects free play. The setting choices for this adjustment are: -Enable -Disable -Factory Setting: Disable
Attract Sound
ATTRACT SOUND This option selects the attract mode sounds. The setting choices for this adjustment are: -Enable -Disable -Factory Setting: Enable
Additional Adjustments Menu
ADDITIONAL ADJUSTMENT MENU To select and set any number of useful adjustments, select the Additional Adjustment Menu. Individual Additional Adjustments are explained in more detail on the following pages.
Press the Volume Up or Volume Down button to highlight the desired Additional Adjustments Menu option on the menu and press the Test button.
ADDITIONAL ADJUSTMENT MENU
CHAPTER 2 DIAGNOSTICS
Game Link Number
GAME LINK NUMBER This allows the game link number to be set. The setting range is: -Maximum: 4 -Minimum: 1 -Factory Setting: 1
Attract Mode Volume
ATTRACT MODE VOLUME This selects the value and setting of the sounds heard during attract mode. The settings for this adjustment are: -Minimum: 0 -Maximum: 255 -Factory Setting: 100
Game Difficulty
GAME DIFFICULTY This determines the level of difficulty for the game. The setting range is: -Easiest -Easy -Normal -Hard -Hardest -Factory Setting: Normal
22 Mipway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Single First Free Game
SINGLE FIRST FREE GAME This enables the single first free game option. The setting choices are: -Enable -Disable -Factory Setting: Enable
Linked First Free Game
LINK FIRST FREE GAME This enables the link first free game option. The setting choices are: -Off -Two Players -Three Players -Four Players -Factory Setting: Off
Game Start Time
GAME START TIME This adjusts the game start time. Use the View 1/View 2 buttons to select. The setting choices are: -Minimum: 30 -Maximum: 60 -Factory Setting: 50
CHAPTER 2 DIAGNOSTICS
Trophy Girls
TROPHY GIRLS This enables the viewing of trophy bearing girls following a race. The setting choices are: -Enable -Disable -Factory Setting: Enable
Speedometer
SPEEDOMETER This allows operator to select the speedometer readout. The setting choices are: -MPH -KPH -Factory Setting: MPH
Language
LANGUAGE This enables operator to select the language the game is announced in. The setting choices are: -English -Espanol -Factory Setting: English
Wheel Strength
WHEEL STRENGTH This selects the degree of wheel strength to be used for racing. The setting range is: -Very Light -Light -Normal -Heavy -Very Heavy -Factory Setting: Normal
24 Mipway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Main Menu
Adjustments, continued
Full Factory Restore
FULL FACTORY RESTORE This allows the operator to restore all settings to the way they were when the game left the factory. The setting range is: -Enable -Disable -Factory Setting: Disable
Main Menu
Volume Level
VOLUME LEVEL To select a desirable volume level, select Volume Level at the Main Menu.
Press the Volume Up or Volume Down button to highlight the Adjust Volume option on the Main Menu, then press the Test button. Remember that the minimum sound level is set under Game Adjustments.
Press the Volume Up button to increase, or the Volume Down button to decrease the sound level of the game. Press the Test button to lock the volume level at the selected value and return to the Main Menu.
Main Menu
Control Calibration
CONTROL CALIBRATION To calibrate the steering wheel and pedals, select Control Calibration at the Main Menu.
Press the Volume Up or Volume Down button to highlight the Control Calibration option on the Main Menu, then press the Test button. Follow the instructions on screen.
CONTROL CALIBRATION
CENTER WHEEL AND PRESS START
WHEEL CENTER: XX
SAMPLE CALIBRATION SCREEN
CHAPTER 2 DIAGNOSTICS
Utilities
UTILITIES To clear bookkeeping memory and reset factory defaults, select Utilities at the Main Menu. Press the Volume Up or Volume Down button to highlight the Utilities option on the Main Menu, then press the Test button. UTILITIES MENU
UTILITIES MENU
The Utilities Menu offers several options. Press the Volume Up or Volume Down button to highlight an option, then press the Test button. Each time an option on the menu is activated you are provided with multiple setting choices.
Use the Volume Up or Volume Down button to change the current value setting and observe a confirmation box as shown below appears.
ARE YOU SURE YOU WANT TO CLEAR CREDITS?
TYPICAL CONFIRMATION BOX
Press the Volume Up or Volume Down button to select YES or NO, then press the Test button to lock in the setting. Selecting NO cancels any changes values and returns the previous values to memory.
Dump Audits
DUMP AUDITS Press the Volume Up or Volume Down buttons to highlight the Dump Audits option on the Main Menu, then press the Test button. This dumps all audits to the serial port.
- Yes
- No
- Factory Setting: No
26 Mipway AMUSEMENT GAMES, LLC
CHAPTER 2 DIAGNOSTICS
Clear Credits
CLEAR CREDITS Press the Volume Up or Volume Down buttons to highlight the Clear Credits option on the Main Menu, then press the Test button. This returns all credit values to zero and removes credit amounts from memory.
- Yes
- No
- Factory Setting: No
Clear Audits
CLEAR AUDITS This select from a menu of assorted audit values that can be returned to zero and remove total from memory, Press the Volume Up or Volume Down buttons to highlight the Clear Audits option, then press the Test button.
CLEAR AUDITS
Each time an option on the menu is activated you are provided with multiple setting choices. Use the Volume Up or Volume Down button to change the current value setting and observe a confirmation box as shown below appears.
ARE YOU SURE YOU WANT TO CLEAR AUDITS?
TYPICAL CONFIRMATION BOX
Press the Volume Up or Volume Down button to select YES or NO, then press the Test button to lock in the setting. Selecting NO cancels any changes values and returns the previous values to memory.
CHAPTER 2 DIAGNOSTICS
Reset High Scores
RESET HIGH SCORES Press the Volume Up or Volume Down buttons to highlight the Reset High Scores option on the Main Menu, then press the Test button. This deletes all high scores and removes player identities from memory.
- Yes
- No
- Factory Setting: No
Default Adjustments
DEFAULT ADJUSTMENTS Press the Volume Up or Volume Down buttons to highlight the Default Adjustments option on the Main Menu, then press the Test button. This sets the adjustments back to their original values.
- Yes -No
- Factory Setting: No
Full Factory Restore
FULL FACTORY RESTORE Press the Volume Up or Volume Down buttons to highlight the Full Factory Restore option on the Main Menu, then press the Test button. This returns every variable in the game to the original factory settings.
- Yes
- No
- Factory Setting: No
28 Mipway AMUSEMENT GAMES, LLC
CHAPTER THREE
SERVICE
CHAPTER 3 SERVICE
SAFETY INSTRUCTIONS The following safety instructions apply to operators and service personnel. Read these instructions before servicing or preparing the Video Game Machine (VGM) for play. Other safety instructions appear throughout this manual.
DEFINITIONS OF SAFETY TERMS. + DANGER indicates an imminent hazard. If you fail to avoid this hazard, it WILL cause death or serious injury. + WARNING indicates a potential hazard. If you fail to avoid this hazard, it COULD cause death or serious injury.
- CAUTION indicates a potential hazard. If you fail to avoid this hazard, it MAY cause minor or moderate injury. CAUTION also alerts you about unsafe practices. + NOTE indicates information of special importance.
MIDWAY AMUSEMENT GAMES, LLC
CHAPTER 3 SERVICE
If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g., seizures or loss of awareness), immediately consult your physician before using any video games.
We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, DISCONTINUE USE IMMEDIATELY and consult your physician.
CHAPTER 3 SERVICE
SERVICING Only qualified service personnel should perform maintenance and repairs. The product guidelines apply to all operators and service personnel. Specific notes, cautions, and warnings appear throughout the manual where they apply. We recommend that you read the SAFETY NOTICES section thoroughly before beginning service. NOTE: Always switch off power to the game machine before servicing.
To service the Marquee... Refer to Marquee Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Remove the tamper-resistant screws used to fasten the marquee to the top of the cabinet. + Lift the marquee straight out from the cabinet and set aside to expose the opening of the cabinet. + Perform the desired repair or equipment replacement. To reinstall, align the contoured marquee with the contour of the cabinet. Fasten in place with the screws provided.
MARQUEE SERVICE
To service the Backlit Marquee ... Refer to Marquee Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Lift open the Marquee Housing. Refer to service instructions for Marquee. + Reach up inside the opening toward the marquee artwork. The marquee artwork and marquee glass is held in place at the top and sides by spacers/brackets fastened with screws. + Remove the screws from each of the brackets. Set the screws and brackets aside until reinstallation. + Lift the marquee artwork or marquee glass out of the housing. + Perform the desired repair or equipment replacement.
To service the Fluorescent Light Assembly... Refer to Marquee Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Lift open the Marquee Housing. Refer to service instructions for Marquee. + Reach up inside the opening in the cabinet and disconnect the power cable from the fluorescent light assembly. + Loosen, but do not remove the screws fastening the assembly to the cabinet. + Slide the assembly slightly forward to disengage the keyholes. Lift out the assembly. + Perform the desired repair or equipment replacement.
4 MIDWAY AMUSEMENT GAMES, LLC.
CHAPTER 3 SERVICE
To service the Fluorescent Lamp or Starter... Refer to Marquee Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Lift open the Marquee Housing. Refer to service instructions for Marquee. + Reach up inside the opening in the cabinet and remove the fluorescent lamp locks. + Both the fluorescent tube and the starter require a quarter turn for removal. Grasp the tube or starter, give it a quarter turn and pull it from its socket. Carefully place a new starter or tube into the sockets and rotate it a quarter turn to reinstall. Reinstall both fluorescent lamp locks. Clean the tube to remove fingerprints and dust.
uN WARNING Fluorescent tubes implode on impact when dropped. Use care in handling.
To service the Cabinet Speakers... Refer to Marquee Service illustration. Speakers are located on the underside of the marquee housing. + Switch off the power to the game machine and unplug the AC line cord. + Lift open the Marquee Housing. Refer to service instructions for Marquee. + Reach up inside the opening in the cabinet and disconnect the speaker wires, including the ground strap. + Remove the nuts on the mounting screws before removing the speakers from the enclosure. Perform the desired repair or equipment replacement. + Carefully reseat the seals upon completing any task in the speaker enclosure. + Reconnect the wires, including ground. Refer to the Cabinet Wiring Diagram for correct speaker polarity.
VIEWING GLASS AND BEZEL SERVICE
CHAPTER 3 SERVICE
To service Viewing Glass... Refer to Viewing Glass and Bezel Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Remove the dashboard. Refer to service instructions for Dashboard.
- Gently slide the viewing glass up and lift it out of the cabinet. Set the viewing glass aside. + Perform the desired repair or equipment replacement. + Clean both the bezel and the viewing glass before reinstallation.
To service Monitor Bezel... Refer to Viewing Glass and Bezel Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Remove the dashboard. Refer to service instructions for Dashboard.
- Gently slide the viewing glass up and lift it out of the cabinet. Set the viewing glass aside. + Grasp the monitor bezel at the bottom and lift it out of the cabinet. + Perform the desired repair or equipment replacement. + Clean both the bezel and the viewing glass before reinstallation.
To service the Monitor (CRT)... We recommend that you read the WARNINGS thoroughly before beginning this procedure.
Switch off the power to the game machine and unplug the AC line cord. Remove the Dashboard, Viewing Glass and Monitor Bezel. Refer to service instructions for the Dashboard, Viewing Glass and Monitor Bezel. + Open the rear cabinet door and disconnect the monitor from the wiring harness and ground wires. Remove 4 nuts securing the monitor mounting flanges to the mounting panel. Pull the monitor carefully from the cabinet and set aside. Perform the desired repair or equipment replacement.
To service the Dashboard... Refer to Dashboard Service illustration. Switch off the power to the game machine and unplug the AC line cord. + Open the rear cabinet door. Label and disconnect all dash wiring, including the ground strap. Remove the four screws used to fasten the Dashboard to the cabinet. Firmly grab the dash and pull it straight out. NOTE: The Dashboard is heavy, with most of the weight concentrated in the center near the Steering Mechanism. Perform the desired repair or equipment replacement. To reinstall, line-up the holes on either side of the Dashboard and push straight back. Check for pinched wires, and then reconnect dash wiring and ground strap. Fasten in place with the screws provided.
6 MIDWAY AMUSEMENT GAMES, LLC
CHAPTER 3 SERVICE
GEAR SHIFT CABLE STEERING MECHANISM
VIEW BUTTON CABLE
DASHBOARD SERVICE
To service the Dash Panel Insert ... Refer to the Dashboard Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Remove the Dashboard. Refer to service instructions for Dashboard. + Remove 4 tamper resistant screws used to fasten the cover to the molded dash and set aside. + Lift the plastic cover plate off of the PCB and dash. + Perform the desired repair or equipment replacement. NOTE: It may also be necessary to remove the Dash PCB. Refer to service instructions for Dashboard PCB. + Reinstall and fasten in place with the screws provided.
To service the Dashboard PCB... Refer to the Dash PCB Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Remove the Dashboard. Refer to service instructions for the Dashboard + Remove the steering wheel, shifter plate assembly, and buttons plate assembly. Refer to service instructions for the steering assembly, shifter and buttons. + Remove 4 tamper resistant screws used to fasten the PCB back plate to the molded dash and set aside. + Remove the tamper resistant screws used to fasten down the dash panel insert. Lift the insert from the dash. + Pull out the PCB back plate from the molded dash. + Remove the ribbon and power cable connections. + Remove the snaps used to fasten the PCB to the back plate. Lift the PCB off the back plate. + Perform the desired repair or equipment replacement. + Connect the ribbon and power cable to a Dashboard PCB. NOTE: The red stripe on the ribbon cable must be lined up with pin 1 on the PCB, and the black wire on the power cable must line up with pin 1 on the power connection for the Dashboard. Reattach the PCB to the back plate, and then fasten the back plate to the molded dash. + Check for pinched wires. Reinstall the Dashboard and fasten in place with the screws provided.
CHAPTER 3 SERVICE
DASH PCB SERVICE
To service Shifter... Refer to the General Dashboard Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Remove the Control Cabinet and the Dashboard. Refer to service instructions for Control Cabinet and Dashboard. + Remove the tamper resistant screws used to fasten the molded plastic cover on the control cabinet. Lift the cover off of the cabinet and set aside. + Label and disconnect all wiring. + Remove the tamper-resistant screws used to fasten both of the faceplates. + Pull the shifter plate and button plate forward enough to expose the switches. Label and disconnect wiring to switches. + Lift button assembly completely out of the dash and set aside. + Remove the bolts used to fasten the shifter enclosure to the dash plate. + Lift enclosure from dash plate. Label and disconnect wires. + Perform the desired repair or equipment replacement. + Reconnect wires and reinstall shifter. + Check for pinched wires. + Fasten the faceplate with the screws provided.
To service Start and View Buttons... + Switch off the power to the game machine and unplug the AC line cord. + Remove the 3 tamper-resistant buttons used to fasten the faceplate. + Pull the plate forward enough to expose the switches. + Label and disconnect the wiring. + Lift assembly completely out of the dash and set aside. + Perform the desired repair or equipment replacement. + Reconnect wires and reinstall buttons. + Check for pinched wires. + Fasten the faceplate with the screws provided.
8 MIDWAY AMUSEMENT GAMES, LLC.
CHAPTER 3 SERVICE
M2298,
Q
GENERAL DASHBOARD SERVICE
To service Steering Assembly... + Refer to the General Dashboard Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Remove the Dashboard. Refer to service instructions for Dashboard. + Remove 6 screws used to fasten the cover plate to the center of the steering wheel. Remove the cover plate and set aside. + Remove the 3 screws used to fasten the wheel hoop to the shaft. Pull the wheel hoop off of the dashboard. Disconnect the harness for the buttons on the steering wheel. + Remove 4 flange nuts holding the motor shield, motor and shaft to the wheel assembly (shield not required on all cabinets). + Slide the motor and the shaft off of the assembly. + Perform the desired repair or equipment replacement. + Reinstall and fasten all items in place with the screws provided.
While the steering mechanism is exposed, inspect the belt for splits in the rubber or other signs of wear at the edges of the teeth. Install a new belt if necessary following the instructions below.
To service Steering Belt... + Loosen four mounting nuts for the motor bracket. + Tighten the tension-adjust bolt only until there is no belt deflection, then loosen the bolt one full turn and tighten the four nuts. + Reattach the mechanism and recalibrate the assembly.
CHAPTER 3 SERVICE
STEERING WHEEL Hoop SERVICE
To service Boost Buttons on the Steering Wheel Hoop... Refer to the Steering Wheel Hoop Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Remove the screws used to fasten the wheel hoop cap to the steering wheel. Lift of the hoop cap off and set it aside with the hardware for reuse later. Lift out the steering wheel spacers. + Gently pull the steering wheel forward enough to expose the boost button cable connector. Unplug the boost button cable. Remove the steering wheel completely from the dashboard. + Turn the steering wheel over to observe the rear side of the wheel hoop. Remove the tamper resistant screws used to fasten the rear cover to the steering wheel hoop. Lift the cover off and set aside with the hardware for reuse later. + Use a desoldering tool coupled with a soldering iron to remove the solder used to attach the cable wires to the button’s switch. NOTE: Use caution when performing this step to avoid becoming burned by liquefied solder and /or to avoid melting plastic parts. + Allow the area surrounding the switch and button to cool properly before proceeding. + Unscrew the nut on the button. Lift the button out of the steering wheel hoop. + Perform the desired repair or equipment replacement. + Be sure to solder the cable wires to the button’s switch when reinstalling a button(s). + Reinstall and fasten all items in place with the screws provided.
To service Lower Cabinet Speaker... This speaker is located just above the pedal assembly. + Switch off the power to the game machine and unplug the AC line cord. + Unlock and remove the rear cabinet door. + Label and disconnect wiring, including the ground strap, to Board assemblies attached to the electronics shelf. + Remove the screws used to fasten the electronics shelf inside the cabinet, then remove the shelf and set it aside. + Locate the speaker. Remove the nuts on the mounting screws before removing the speaker from the enclosure. + Perform the desired repair or equipment replacement. + Carefully reseat the seals upon completing any task in the speaker enclosure. + Reconnect the wires, including ground. Refer to the Cabinet Wiring Diagram for correct speaker polarity.
10 Mipway AMUSEMENT GAMES, LLC
CHAPTER 3 SERVICE
To service Pedal Assembly... + Switch off the power to the game machine and unplug the AC line cord. + Adjust the seat to the maximum rear position. + Remove 4 tamper resistant screws used to fasten the Pedal assembly to the cabinet. NOTE: Due to the weight of the pedal assembly it may slide or abruptly jerk out of the opening once all screws are loosened and/or removed. + Pull the assembly forward enough to expose wiring. Carefully note the orientation of the cable wiring. Label and disconnect wiring, including ground. + Perform the desired repair or equipment replacement. Reinstall pedal assembly and reconnect wiring, including ground. + Align the holes for the screws and fasten in place with the hardware provided.
To service Coin Meter... + Switch off the power to the game machine and unplug the AC line cord. + Unlock the cash door and swing it open. Remove the cash tubs. + The meter is located on a plate at the vault bottom. Remove the screws and lift the plate just enough to disconnect the meter wires from the harness. + Record the meter count before testing or replacement. + Perform the desired repair or equipment replacement.
To service Coin Mechanism... + Switch off the power to the game machine and unplug the AC line cord. + Unlock the coin door and swing it open. + Unlatch and remove each coin mechanism separately to clean or replace with a different type. Ensure mechanism seats fully in the holder upon reinstallation. Close and lock the release latch, then close the door. + Turn on the game and change the mechanism setup, then test known good and bad coins to verify operation.
DOLLAR BILL VALIDATOR SERVICE
CHAPTER 3 SERVICE
To service Dollar Bill Validator... (Use MARS AE2411-U3 UL recognized currency changer) Dollar bill validators or other currency acceptors may be installed in games that are manufactured with the additional wiring connector. + Switch off the power to the game machine and unplug the AC line cord. + Unlock the coin door and swing it open. Read the label affixed to the door for additional information. + Disassemble the validator and remove material to permit it to fit inside the coin door as illustrated then reassemble unit.
To service PCB Board Assemblies... Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear door. Remove the screws used to fasten the hinged, metal cage covering the PCB Assembly. + Open the cover, which is hinged along the bottom edge, to expose the PCB assembly. Carefully note the orientation of the JAMMA connector and the other cables. Extract the harness and other cables from the board connectors. Remove the mounting screws from the desired circuit board assembly. Lift the board out of the cabinet and set in a safe place. Use anti-static bags and protective containers from new parts for storage if not reinstalled immediately. Perform the desired repair or equipment replacement. Be certain to reinstall the perforated cover so that it seals against the metal plate.
To service Wheel Driver Board Assembly... + Switch off the power to the game machine and unplug the AC line cord. + Unlock and remove the rear door. + Remove the screws used to fasten the hinged, perforated metal cage covering the PCB Assembly. + Open the cage, which is hinged along the bottom edge, to expose the PCB assembly. + Carefully note the orientation of the cables. Extract the harness and other cables from the board connectors. + Remove the wheel driver board assembly mounting screws. Lift the board out of the cabinet and set in a safe place. Use anti-static bags and protective containers for storage if not reinstalled immediately. + Perform the desired repair or equipment replacement. + Be certain to reinstall the metal cover so that it seals against the metal cage.
To service the Main Boot, PIC or Sound ROM... The ROM (Read Only Memory) circuits contain the computer operating instructions for the game. The Main Boot ROM is located on the Mango PCB; the sound ROM is located on the Vegas SIO PCB; the PIC chip is located on the Vegas SIO PCB.
Memory devices are especially sensitive to static charges. Use grounding precautions when handling these parts. Switch off the power to the game machine and unplug the AC line cord. + Unlock and remove the rear door. Remove the screws used to fasten the hinged, metal cage covering the desired PCB Assembly. Open the cover, which is hinged along the bottom edge, to expose the PCB assembly. Carefully note each IC position, and then remove using a chip extraction tool. To install memory circuits, orient a chip over the corresponding socket and press firmly to seat pins. Do not force.
12 Mibway AMUSEMENT GAMES, LLC
CHAPTER 3 SERVICE
To service the Battery... + Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear door. Remove the screws used to fasten the hinged, metal cage covering the PCB Assembly. Open the cage, which is hinged along the bottom edge, to expose the PCB assembly. Locate the battery on the Vegas SIO Board assembly, and then remove using a chip extraction tool. To install a battery, orient a battery over the corresponding socket and press firmly to seat. NOTE: Do not force; the battery is notched and will only fit in the socket one way.
To service an Auxiliary Board Assembly... Switch off the power to the game machine and unplug the AC line cord. Unlock and remove the rear door. Remove the screws used to fasten the hinged, metal cage covering the PCB Assembly. + Open the cover, which is hinged along the bottom edge, to expose the PCB assembly. Carefully note the orientation of the cables. Extract the harness and other cables from the board connectors. Remove the assembly mounting screws. Lift the board out of the cabinet and set in a safe place. Use anti-static bags and protective containers for storage if not reinstalled immediately. Perform the desired repair or equipment replacement. Be certain to reinstall the metal cover so that it seals against the metal cage.
To service the Power Supply... + Switch off the power to the game machine and unplug the AC line cord. + Unlock and remove the rear cabinet door. + Unplug the IEC AC connector from the rear of the supply and the DC connector from the front. + Remove the two front and two rear screws from the supply, then lift it off of the power chassis. Note voltage setting. + Perform the desired repair or equipment replacement. + Be sure to set the voltage switch to the correct value prior to reinstallation. + Set the supply on the power chassis and align the mounting holes. Install the four screws and the two power connectors.
To service the Transformer... + Switch off the power to the game machine and unplug the AC line cord. + Unlock and remove the rear door. + If the power to the Video Game Machine (VGM) was only recently disconnected, the transformer may still be warm. Allow the transformer to cool completely before handling. + Label and disconnect all wiring, including ground. + Remove the screws used to fasten the transformer to the base of the cabinet. + Perform the desired repair or equipment replacement.
CHAPTER 3 SERVICE
To service Fan Assembly... + Switch off the power to the game machine and unplug the AC line cord. + Unlock and remove the rear door. + Remove the perforated metal cover to expose the fan assembly and set aside. + Unplug the fan power connector from the wiring. + Remove the screws used to fasten a fan down and then lift fan out. + Perform the desired repair or equipment replacement.
To service Speakers in Head Rest... Refer to the Seat Pedestal Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Remove the tamper resistant screws from the speaker grille. + Remove the tamper resistant screws used to fasten the speaker plate to the seat and pull forward. + Label and disconnect wires, including ground. + Remove the nuts used to fasten the speaker to the plate and remove speaker(s). + Perform desired repair or equipment replacement. + Reinstall the speaker(s) to the speaker plate and reattach wiring, including ground. Attach the speaker plate to the seat. + Reinstall speaker grille and fasten in place with hardware provided.
To service Speaker in Seat Back... Refer to the Seat Pedestal Service illustration. + Switch off the power to the game machine and unplug the AC line cord. + Remove the tamper resistant screws used to fasten the grille to the seat and pull forward. + Label and disconnect wires, including ground. + Remove 4 Phillips head screws used to fasten the speaker to the seat and remove speaker. + Perform desired repair or equipment replacement. Reinstall speaker and reattach wiring, including ground. Reinstall speaker grille and fasten in place with hardware provided.
To service the Seat Slide Assembly... Refer to the Seat Pedestal Service illustration. Switch off the power to the game machine and unplug the AC line cord. Disconnect the Seat Assembly from the cabinet by removing the tamper resistant screws used to fasten the assembly to the slide rails in the cabinet. Slide the Seat Assembly halfway back along the rails to expose wiring. Disconnect the speaker cable and slide the seat the rest of the way off the rails. Remove 3 tamper resistant screws from each side of the seat mounting plate. Lift the seat and mounting plate assembly off the pedestal and set aside. Slide the seat assembly forward, and remove the two tamper resistant screws from the rear of the metal panel on top of the pedestal assembly. Slide the seat assembly backward and remove the two tamper resistant screws from the front of the metal panel. Lift the metal panel out of the pedestal base and turn the unit over. Remove the four nuts holding the metal panel to the slide assembly. Set the metal panel aside and slide assembly is exposed. Perform the desired repair or equipment replacement. Reinstall by performing the steps in reverse and fasten in place using the hardware provided.
14 MIDWAY AMUSEMENT GAMES, LLC
CHAPTER 3 SERVICE
- TAMPER gESISTANT SCREW #815/8. PH) NASER)
‘Levey raweer aesistavr senew 45/8 PA w/ WASHER
pce sen |
=, reer. Reason socw SPAT SLIDE MOUNTING e700 /2 OER
(Lock ase 2-20 INTERNAL TOOT
- Far asic
(©) Looe waste sur
o
1 ? tf
\
SEAT PEDESTAL SERVICE
CHAPTER 3 SERVICE
To service the Seat Assembly... The Seat Assembly includes the pedestal base. Refer to the Seat Pedestal Service illustration. Switch off the power to the game machine and unplug the AC line cord. Disconnect the Seat Assembly from the cabinet by removing 8 tamper resistant screws used to fasten the assembly to the slide rails in the cabinet. Slide the Seat Assembly halfway back along the rails to expose wiring. Disconnect the speaker cable and slide the seat the rest of the way off the rails. Remove 3 tamper resistant screws from each side of the seat mounting plate. Lift the seat and mounting plate assembly off the pedestal. Place the seat on its back, on a flat surface. Perform the desired repair or equipment replacement. Reinstall using the hardware provided.
16 MiDway AMUSEMENT GAMES, LLC
CHAMPIONSHIP FACING
CHAPTER FOUR
PARTS
equipment damage! Use only Midway authorized parts. + For safety and reliability, substitute parts and modifications are not recommended.
CHAPTER 4 PARTS
Cabinet Front View
04-12542.1-1 D MARQUEE — ee MOLDE!
_ 8675-16273-00 MID RESOLUTION 27” MONITOR 03-9893.1 MONITOR BEZEL o1-14892 | . SPEAKER GRILLE
PEDAL SH EMBLY (SEE DETAIL 0!
04-12921.1 MAIN. CABINET
04-10635 COIN VAULT ENCL' 2E
OTHER COMPONENTS 04-12461-1 LEFT DASH BRACKET 04-12461-2 RIGHT DASH BRACKET H-23627.1 SERIES SPEAKER CABLE H-23277 SEAT POWER CABLE 04-11253-1 LEFT MONITOR BRACKET 04-11253-2 RIGHT MONITOR BRACKET SEAT/PEDESTAL (SEE DETAI
CABINET BA:
CABINET MOUNTING HOLES 04-12959 PORT BEAM
CABINET
700+ 00033 00 CaTWaSHER
4701-00005-00 SPLIT LOCKWASHER (8)
- 1/4 §
4320+ 01 16-20 -20B _
- 1/420 /: 4701-00005- 00 oo 4700- 00033 oop | | eedesta 7/84%3/ 4415 TAMPER RES
2 Mipway AMUSEMENT Games, LLC
CHAPTER 4 PARTS
Caster & Leveler Assemblies
SWIVEL CASTER
20-10361
- swe Locking — CASTER
"\g08-01219-11
- #8 x 11/16 C PIN HEAD SPECAL So KON 4420-01141-00 \ \\_4424-01182-00 (28) FUNGE NUT 1/4
- aM NUT 1/2=13
Rear Door Assembly
01-898 UPPER IR LOCK CAM 01-7264 LOCK RETAINER PLATE 4420-01141-00
- 1/4-20 FLANGRIP NUTS 4108-0121 fo
- 8-32 x 11/16 $
__01-11285 jf OCK PLATE
20-10350 DOOR LOCK CAM ASSEMBLY 4420-01141-00 |
- 1/4-20 FLANGRIP NUTS
4320-01164-20B
- (2) 1/4-20 X 1 1/4 FLAT HEAD BOLTS
KEYS PART ¢ CAM Li DOOR BRACKET “14-1250 REAR WOOD DOOR
03-7602 | ENT HOLE COVER ss 4320-01164-20B
- 1/4-20 x 11/4 FLAT HEAD OLTS
CHAPTER 4 PARTS
Cabinet Rear View
01-10714 LINE CORD COVER
-14632-00 OFF SWITCH
03-8326 J (2) HANDLE PULL/VENT / 5555-16059-00
01-13980 FRONT GRILLE FER SPEAKER
SUPPLY TAIL DRAWING)
CTRONICS ASSEMBLY EE DETAIL DRAWING)
PEDESTAL DETAIL DRAWING)
SWIVEL CAS MAIN. CABIN (SEE DETAIL DRAWING) H-23740__/ 6.5 SUB WOOFER SPEAKER CABLE
TRANSFORNER (SEE APPLICATION CHART)
TER WHEE DETAIL DRAWING) OTHER COMPONENTS H-23628 MAIN HARNESS. 01-11287 KEY LOCK BRACKET LINKING CABLE, \ . ee Sy a Cys
Pedal Assembly 20-10135
Mipway AMUSEMENT GAMES, LLC
CHAPTER 4 PARTS
Marquee Assembly
a xt 4006-01204-128
TAMPER RESISTANT SCREWS
402001100-16,
- 1/4-
x .087 ER 4700.00052-008 x 625 x 08
BACK FLAT w
04 12540.1-4 SW” MOLDED WARQUEE—\
440801126-00
- 6-32 KEPS NUT '5555-15098-00 ‘SPEAKER 51/2"
CHAPTER 4 PARTS
Seat Pedestal Assembly 31-3525-1 01-14945.2-1 \( UPPER SEAT DECAL [— yppeg
4408-01119-00 / (4) 8232_KEPS NUTS / 5555-16234-00 / (2) 3" FULL RANGE SPEAKER
01-14945.2-2 MIODLE SEAT PLATE 04-12815-1 SPEAKER GRILLE
" \ 4108-01193-10B OA 12674-1 \ (16) TAMPER RESISTANT SCREW Ges a PH W/ WASHER f (4) MACHINE
| 5555-16059-00 4020-01100-08 [/ SPEAKER Wh (6) TAMPER RESISTANT SCREW / {31-3538 20x1/2 BH WOOFER GRILLE
SEAT SLIDE Mt
4108-01193-10B AMPER RESISTANT SCREW #8x5/8 PH W/ WASHER Ares 00014-00B
4700-00131-00 —(6) FLAT WASHER 3/8
4701-00006-00 ———(8) LOCK WASHER 3/8 SPL
at 01070-12 4020-01148-40
4108-01042-12
- (3) #8 X 3/4 P-FH 01-15250 SHEET METAL SCREW ‘SEAT PLATE
SEAT SUDE
04-12011 PEDESTAL
OTHER COMPONENTS H-23579 SEAT SPEAKER CABLE 01-15251.1 ROLL BAR BRACKET \ 23-6822 \. PEDESTAL FLOOR MAT
6 Mipway AMUSEMENT GAMES, LLC
CHAPTER 4 PARTS
Lamp Assembly A-23252
-— 20-10444 AMP HOLDER
04-12732 NT HOUSIN! Mae 4002-01105-04 >—PH
20-10481.2 ECTRONIC BALLAST
\ 24-8809 Of 24-8874
FLOURESCENT 8ULB 18” 15W
04-11106 -—— 20-10443 HOUSING ASSEMBLY \, ~ “LAMP HOLD ‘STARTER —— 20-10480
20-10444 fo 4408-01128-00 NUT 8-32 KEPS
BALLAST CHART BELC
CONVENTIONA\
20-10263 20-8749-8 20-10220 20-10384 20-10379 20-10380 20-10236— 240V0LT —— 24-8809 OR 24-8874 FLOURESCENT BULB 18" 15W
AC Power Assemblies
5102-14240-00 LINE FILTER 5733-12869-00 PANEL FUSE HOLDER
(2)
04-12639.2 AC PLUG BRACKET“ AND PLUG
Mipway AMUSEMENT GAMES, LLC
STEERING MECHANISM
(SEE DETAIL DRAWING) 04-12908.1__/
DASH SUPPORT BRACKET
H28218 Lo DASH LE) —
POWER CABLE
5795-15667-15, / 28 PIN RIBBON —“ BLE 4420-01185-00 4700-00135-00B __/
- .265 X .626 X .067 [ (4) 1/4-20 N
STEERING
AND RELATED 4701-00003-00B
— (4) SPLITWASHERS
4008-01 100-12 Dashboard Assembly CHAPTER 4 PARTS
CHAPTER 4 PARTS
Steering Wheel
4028-01191-16B /—SOCKET HEAD BOLT T 1/4-28 x 1 STEERING ¥ MECHANISMS / (SEE DETAIL I 02-5391.2 20-10189 “LO! HUB SHER a a EXTERNAL TOOTH
“ EL IS AND CABLE
02-5164 ) STEERING WHEEL SPACER
CABLE SHIELD
H-23780.2 —
4427-01183-00 JAM NUT, 1/2-2 / > A70%-00005-008_/_/4020-01100-24
- 1/4 B aol (3) 1/4-21 sen. TAMPER RESIS
Button Plate Assembly A-23562
oN BUTTON PLA
31-3530-1 BUTTON —~ vil 1 31-3530-3
RED — vil SH BUTTON
H-23259 / VIEW SWITCH HARNESS
31-9530-2 OVAL PUSH BUTTON RED — VIEW
Mipway AMUSEMENT GAMES, LLC 20-10183
SHAFT KEY
Steering Mechanism 20-10713 CHAPTER 4 PARTS
CHAPTER 4 PARTS
Coin Door Assembly
KEY
CAM LU
5 27-3729 27-3725 7 BUTTON BEZEL ENTRY/REJECT / BUTTON NUT WASHER
CAM LOCK ARM——4
27-3730 or 27-3733 REJECT BEZEL
BLANKING PLATE
03-8863 CASH TUB
STEEL ENCLOSURE
5580-13476-00 COIN METER
CHAPTER 4 PARTS
Power Supply 20-10537
RY POWER LINE CORD —~,
INTERNAL 12VDC FAN
53, Ki2. CABLE
5060-15755-00 NE FILTER (REQUIRED FOR EUROPEAN MODELS) o i890 D.C. MAIN POWER |
- POWER SUPPLY CONNECTOR MOUNTING BRACKETS
| PINS | FUN | COLOR |
| 2,3 | +5 VOC | _RED |
5,6,7,8 GROUND BLACK
| =5 | VOC | WHITE |
2 VDC YELLO! 12 VDC BLUE
Electronics Assembly A-23566
| .5556-10056-00 | j | Bessi8 | |
| LA | FERRITE BEAD 1-1/4 SPLIT | [ | ciRCUT eoaRD HARNESS |
ZA sccessera.00 “\ J oa FERRI EAD 3/8” SPU. a
Zee 1B-32K5/16 P—PH a o A-23645 | a CPU BOARD ASSEMBLY —— on ya NXT a 6 i ZA ~ SOUND 1/0 BOARD ASSEMBLY a
- -4008-01008-1 GOSSEREN ge—sax5/8 PP
sresse200-12 L 1 RIBBON CABLE, 40-2N 12”
| Abos.01005-10 | 2o-10460 | 4002-01005-10 | |
| >< N SCR | SHIELDED VIDEO CABLE | {19} | SUREN f8-32%5/8, |
. \e-2H \\ ousrians ruesrat a 2010590 W\ ~FLEXILE GROMMET 7
osiame . ou
- ccron SERB wooo exzoreo ee RES sus oraonos
4498-01 128-00 GY NUT #32 LX otras WHEEL ORVER BOARD ASSEMBLY HINGE (PART OF GROUNDPLAN
OTHER COMPONENTS GckARSHER 6 SPLIT 20-10383 HARD DRIVE POWER CABLE (4) SCREW #6—32x2 PL-HWH
12 Mipway AMUSEMENT GAMES, LLC
CPU Board Assembly A-23645,
Field Replaceable CPU Board Parts CHAPTER 4 PARTS
DESIGNATION PART NUMBER FUNCTION DESCRIPTION U19 A-23315 Bus Controller Configuration Programmed Logic Device
| U22 | A-22912 | CPU Configuration | Programmed Logic |
Device
| U27 | A-5343-40090-1 | CPU Boot ROM | EPROM Assembly |
| U28 | - | CPU Expansion ROM | EPROM Assembly |
(empty)
CHAPTER 4 PARTS
Sound I/O Board Assembly A-23646-1
Field Replaceable Sound I/O Board Parts DESIGNATION PART NUMBER FUNCTION DESCRIPTION U28 5880-15774-00 Memory Backup. Batttery U37 A-23647 PIC Assy 40095 EPROM Assembly U44 A-5343-40090-2 Sound EPROM Assembly
Mipway AMUSEMENT GAMES, LLC
Field Replaceable Wheel Driver Board Parts Wheel Driver Board 04-12770.1 CHAPTER 4 PARTS
DESIGNATION PART NUMBER FUNCTION DESCRIPTION Fi, F2 5731-14094-00 Circuit Protection Fuse 41A SB F3 5731-15627-00 Circuit Protection Fuse .63A FB
U3 A-23362 Controller PLD Assy Primary U3 A-23363 Controller PLD Assy Secondary
CHAPTER 4 PARTS
Line Cord Application Chart Part Number
| 5850- | 5850- | 5850- | 5850- | 5850- | 5850- | 5850- | |
| 14699- | 14699- | 14699- | 14699- | 14699- | 14699- | 14699- | |
| COUNTRY | 00 | 01 | 02 | 03 | 04 | 05 | 06 |
Australia x Austria Belgium Canada x Denmark x
x
Finland France Germany Holland Hungary Italy x Japan x New Zealand x Norway x Spain x Switzerland x United Kingdom x United States x x | x |< |< |x |<
Coin Door Application Chart Part Number 09-96023- Country 02 | 03 | 04 | 06 | 07 | 09 | 11 | 13 | 14 | 15 | 17 | 18 ) 20 | 22 | 23 | 24 | 33 Australia x Austria x Belgium x Canada x Denmark x Finland x France x Germany x Holland x Hungary x Italy x Japan x New Zealand x Norway x Spain x Switzerland x United Kingdom 09-80000 United States x
16 Mipway AMUSEMENT GAMES, LLC
CHAPTER 4 PARTS
Transformer Assembly (Refer to application chart)
aH Thy
Transformer Application Chart Voltage Part Number & Country 5610-14926-00 5610-14927-00 5610-15275-00 230 VAC Australia x 230 VAC Austria x 230 VAC Belgium x 230 VAC Canada x 230 VAC Denmark 230 VAC Finland 230 VAC France 230 VAC Germany 230 VAC Holland 230 VAC Hungary 230 VAC Italy 100 VAC Japan x 230 VAC New Zealand 230 VAC Norway 230 VAC Spain 230 VAC Switzerland 230 VAC United Kingdom 120 VAC United States x x |x|] x] x] x | x
x | x |x |< | x
CHAPTER 4 PARTS
Supplementary Parts
Power & Protection AC Line Filter, 6A, 250V 5102-14240-00 Ferrite Bead 5556-15272-00 Ferrite Beads 5556-13956-00 Fuse, 0.63A, 250V, FB, 5x 20 mm | 5731-15627-00 Fuse, 3A, 250V, SB, 1/4x 1 1/4 5731-10356-00 Fuse, 4A, 250V, SB, 5 x 20 mm 5731-14094-00
Cables 26-Pin Ribbon Cable 5795-15667-48 AC Line Harness H-23626.2 Gear Shift Cable W/Dual Grd. H-23949 Dash LED Power Cable H-23218 40 ckt Ribbon Cable W/Grd Bus 5795-16308-12 Bill Acceptor Adapter Cable H-23639 20 Pin Ribbon Cable 5795-10937-18 Circuit Board Harness H-23618.2 Shielded Video Cable 20-10493 Dash Cable H-23259 Linking Cable 5797-15276-00 Flourescent Lamp Cable H-22507 Hard Drive Power Cable 20-10383 Series Speaker Cable H-23627.1 AC IDC Cable H-20353 Main Wiring Harness H-23628.6 Seat Speaker Harness H-23579 Seat DC Power Cable H-23277 Grnd Braid With Ring Term H-22327-86 Illuminated Button Inter Cable H-23780.2 Noise Reduction Fan Inter Cable H-23880
Documentation Caster Installation Instructions 16-11010 Operators Manual 16-40090A-101 Product Registration Card 16-10650
Tools & Game Installation Hardware Bolt,Hex Head, 1/4-20 x 1 4320-01124-16 Bulb, #555, 6.3V, .25 Amps 24-8768 Bulb, #161 24-8840 Crossover Coupler 5796-15262-00 Screw, SMS, #8 x 1 1/2 TRX 4108-01160-24B Screw, Tamper-Resistant, 1/4-20 1 1/4 4020-01100-20 T-20 Tamper-Resistant Wrench 20-9620 T-27 Tamper-Resistant Wrench 20-10140 Washer, Flat, .265 x 1.00 x.067 4700-00135-00B Washer, Flat, .265 x .750 x .067 4700-00033-00 Washer, Lock, 1/4 Split 4701-00005-00B Washer, Lock, 1/4 Internal Tooth 4702-00014-00B
Mipway AMUSEMENT GAMES, LLC
CHAPTER FIVE
WIRING
CHAPTER 5 WIRING
JAMMA CHART
| Function | Wire Color | Pin | Pin | Wire Color | Function |
| Ground | Black | A | 1 | Black | Ground |
| Ground | Black | B | 2 | Black | Ground |
| +5VDC | Red | Cc | 3 | Red | +5VDC |
| +5VDC | Red | D | 4 | Red | +5VDC |
| -SVDC. | Yellow | E | 5 | Yellow | -5VDC. |
| N/C | FE | 6 | Orange | +12VDC. | |
| Key | H | 7 | Key | ||
| Coin Counter 2 | Brown/Red | J | 8 | Brown | Coin Counter 1 |
| Nic | K | 9 | N/C | ||
| -Cabinet Speaker | Brown/Gray | L | 10 | Red/Gray | +Cabinet Speaker |
| N/C | M | 11 | Red/White | +Seat Speaker | |
| Video Green | Yellow/Green | N | 12 | Yellow/Red | Video Red |
| Video Syne | Yellow/White | P | 13 | Yellow/Blue | Video Blue |
| Service Credits | White/Gray | R | 14 | Yellow/Black | Video Ground |
| Slam Tilt | Black/Green | Ss | 15 | Black/Blue | Test Switch |
| Coin 2 | Black/Red | T | 16 | Black/Brown | Coin 1 |
NIC U 17 White Start
| Gear 1 | Green/Black | Vv | 18 | N/C | |
| Gear 2 | Green/Brown | Ww | 19 | N/C | |
| Gear 3 | Green/Red | x | 20 | N/C | |
| Gear 4 | Green/Orange | Y | 21 | N/C | |
| N/C | Z | 22 | White/Yellow | View 1 Switch | |
| N/C | a | 23 | White/Green | View 2 Switch | |
| N/C | b | 24 | White/Blue | View 3 Switch | |
| N/C | c | 25 | N/C | ||
| N/C | d | 26 | N/C | ||
| Ground | Black | e | 27 | Yellow/Brown, Black | Ground | |
| Ground | Black | f | 28 | Black | Ground |
SOLDER SIDE COMPONENT SIDE
DASHBOARD WIRES (NOT PART OF THE MAIN JAMMA HARNESS)
| WHEEL MOTOR BLACK _| Brown/White - | Green/Black | GEAR SHIFT 1 (1st) | |
| WHEEL MOTOR RED | Brown + | Green/Brown | GEAR SHIFT 2 (2nd) |
| Red | +5V STEERING | Green/Red | GEAR SHIFT 3 (3rd) |
| Orange/Blue | STEERING POSITION | Green/Orange | GEAR SHIFT 4 (4th) |
| Black | GROUND STEERING | Black | GEAR GROUND |
DC POWER SOURCE VOLTAGE LIMITS
| Function | Range Limits | ID | ID | Range Limits | Function |
| Digital Circuits | +4.90V to +5.10V | +5V | -5V | -4.75V to -5.25 | Audio lights |
| Audio; DBV | +11.5V to +12.5V | +12 | NOTE: +5V is adjustable on the power supply |
MIDWAY AMUSEMENT GAMES, LLC
WHEEL DRIVER BOARD
Main Cabinet Wiring
CHAPTER 5 WIRING
cnt)
| (—| | [MONITOR] [13 |'3 beaten | ae | 4 | ||||
| | | fc | — | |||||
| alsa | (Connects to | ino. | se 193 | ||||
| $ ot | a | Coole | |||||
| 3 of | eatin | See also Power | if | ., | |||
| li | 33 | Siang toga | sen wes vin yo | ||||
| a | 6 ort | 3 | Sean | wale | (WEE. wate pan vu | ||
| % | |w | oot | Ean | TR hy _ axe | 2giz | are moo — ean | TO |
| < | 9b | Ea | bee dey sox Guy | Belk | — | 26 | |
| a | fs | 932] | \gerwigr sex — view 2 La | _ | (Steer euTTON —war 194 |
fe Ae ag eens
| AIT ANT | : | ry | |||
| be | a2 erik | GND | peas | RG RT O35 | |
| SIE | Pn | neo snc MS? sep sue | ——~ | ow | Pracsaned |
wae seu ogy na
Clevae BLUI5 6 [she ong_1iavo SAS? one auk 3| |- ijrigvac use ORC SK)
| a | | | COMET |
3 powtah Stl
20 A20 AS
2} 34 CONNECTS 10
| Connects | 3) 3 fa et | Lune WOUTAGE CELE arg | ||
| Vine "Vortage | if | O48) 8 | esvac | sep ae |
Mba’ Degen) TIONAL MOTION SEAT L_ WIRING DIAGRAM
TD CONTROL PANE!
isl
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
CHAPTER 5 WIRING
Control Panel Wiring
Mipway AMUSEMENT GAMES, LLC Power Inlet Mounting Plate
CONNECTS TO
N eae) R MAI NG DIAGRAI Eon Specific Fuse.
SUPPLY a
Mount Sau
[ 2 Note 2) BLK RED. BLK YEL_HOT
RN YEL
NEUTRAL
wat RED
ONITOR ALSO. MAI NG DIAGI
FLUORESCENT LAM
(a ausck aLacK
GaN VEL
N M IDC AC Power Cable ¢ Bill Acceptor
ONNECTS TO HARNESS SO MAIN DIAGRAI ALK I ie} aLAck CRN YE WHITE rr) mo
THT
6d500566 Earth 6 to stud on Pi located in the Mor
- RATING OF CIRCUT BREAKER FUSE LTAGE SWITCH ON POWER SUPPLY
RATING VOLTAGE | FUSE 20 SR
RED_ Wet KEY RED wer BN wi EEN WET ia Ne RED Rw BRN GRW ‘GRA YEL GRAVEL GRAVEL RED WHT
: ° wan vo GaN VEL Ban WT
GaN -YEL ae
SEAT SPEAKER CABLE H-23579 RED RN
GRILL SPEAKER | COIN DOOR FRAG
ono wat ppv RN YE RN YE RN YE
GRN YE Power Wiring Diagram CHAPTER 5 WIRING
CHAPTER 5 WIRING
DIP SWITCH U13 SETTING TABLE FUNCTION Swi | SwW2 | SW3 | SW4 | SW5 | SW6 | SW7 swe DIP COINAGE OFF CMOS COINAGE ON* USA 13 GER1 FR ECA1 UK1 ECA OFF | OFF | OFF
| USA 11 GER2 FR ECA2 UK2 ECA | ON | OFF | OFF | |
| USA 10 GER3 FR ECA3 UK3 ECA | OFF | ON | OFF |
| USA 1 GER4 FR ECA4 UK4 | ON | ON | OFF |
| USA DC8 GERS5 FR ECA5 UK5 | OFF | OFF | ON | |
| USA DC6 GER ECA1 FR ECA6 UK6 ECA | ON | OFF | ON |
| USA DC5 GER ECA2FR ECA7 UK7 ECA | OFF | ON | ON |
| USA DC1 GER ECA3 FR ECA8 | ON | ON | ON |
| FREE PLAY (UK) | ON | ON | ON |
USA OFF | OFF
| FRANCE | ON | OFF |
| GERMANY | OFF | ON |
| UK** | ON | ON |
UNUSED OFF ON
UNUSED OFF ON
DIP Switch Setting for Coinage There are many ways to select the type and quantity of currency recognized by the game machine.
- The most common coin combinations for several countries are pre-programmed and may be selected from the table when Standard Pricing is activated (see Game Adjustments).
- DIP Switch settings may be changed with the power switched on. Set any switch then observe the screen to verify that the desired selection is enabled. NOTE: If CMOS coin settings are active, switch settings for an individual Country will have no effect.
- Some European countries may accept currency used in other countries. The most popular coinage settings are listed in the Pricing Table.
DIP SWITCH U12 SETTING TABLE
Function swi Sswe2 SW3 SW 4 sws SW6 SW7 SsWw8
Unused OFF ON
Unused OFF
Unused OFF
Unused OFF
Unused OFF
Brake Enabled OFF Brake Disabled ON
Unused OFF ON
Game Mode OFF Test Mode ON
CHAPTER 5 WIRING
CPU BOARD JUMPER LOCATION TABLE
| Jumper | J1 | J2 | J3 | J4 | J5 | J6 |
| Location | U28, PS | U28, PS | U28, PS | U28, PS | U28, P5 | U22, U27 |
CPU BOARD JUMPER POSITION TABLE
| ROM Type | Default | Options* | J1 | J2 | J3 | J4) | J5 | J6 |
| Boot (U27) | 27C080, 1M X 8, EPROM | 1-2 | 2-3 | 1-2 | 1-2 | |||
| * | 27C040, 512K X 8, EPROM | 1-2 | 1-2 | 1-2 | 1-2 |
27C010, 128K X 8, EPROM 1-2 | 1-2 | 1-2 | 2-3 29F040, 512K X 8, Flash 2-3 | 1-2 | 23 | 1-2 29F020, 256K X 8, Flash 1-2 | 1-2 | 2-3 | 1-2 29F010, 128K X 8, Flash 1-2 | 1-2 | 2-3 | 1-2 Expansion (28) 27C080, 1M X 8, EPROM 27C040, 512K X 8, EPROM 27C010, 128K X 8, EPROM a
External Boot Boot from CPU ROM Empty Boot from SIO ROM
Notes on CPU Jumper Position
- Boxes containing “----” means not applicable
- Memory type numbers shown are for blank parts. Your game requires programmed parts.
SOUND SIO BOARD JUMPER POSITION TABLE
Jumper Location Function Meaning Position State
| J1 (Note1) | U9, Y3 | /O Connector P2 | Input Mode | Pins | 1&2 | * |
| Output Mode | Pins | 2&3 | |||
| J2 | U35, U10 | Video Sync | Positive Sync | Jumper not installed | * |
Negative Sync Pins 1&2
| 3 (Note 2) | U15 | /O Connector P4 | Input Mode | Pins | 1&2 | . |
Output Mode Pins 2&3
| J4 | None | None | Not used | None | oa |
| J5 (Note 2) | U15, P2 | /O Connector P4 | Input Mode | Pins | 1&2 | . |
| Output Mode | Pins | 2&3 | |||
| J6 | None | None | Not used | None | oa |
| J7 | None | None | Not used | None | on |
| J8 (Note 1) | U9, P4 | /O Connector P2 | Input Mode | Pins | 1&2 | * |
Output Mode Pins 2&3 Notes on SIO Jumper Position
- Configure I/O port P2 by setting both jumpers J1 and J8 to input or output mode.
- Configure I/O port P4 by setting both jumpers J3 and J5 to input or output mode.
MIDWAY AMUSEMENT GAMES, LLC
CHAPTER 5 WIRING
SOUND I/O BOARD LED INDICATOR STATUS TABLE
LED Location Function Color State Meaning
| LED 1 | Ut1 | Not Used (Remains Off) | Green | OFF |
(Note 1) ON BLINKING ~
| LED 2 | U34, Y1 | Linking Connector Status | Green | OFF | Not in use (No game linking) |
| (Note 2) | ON | Link continuity good | |||
| LED 3 | JAMMA | -5V power indicator | Red | OFF* | No power | |
| (Note 2) | Connector | ON* | Normal operation | ||
| LED 4 | U35, P14 | +12V power indicator | Red | OFF | No power | |
| (Note 2) | ON | Normal operation | |||
| LED5 | P23 | +5V power indicator | Red | OFF | No power |
| (Note 2) | ON | Normal operation | |||
| LED6 | U34, Y1_ | CPU linking activity | Red | OFF | Not in use | |
| (Note 2) | ON | CPU and ethernet contact | |||
| LED7 | U34, Y1 | Linking and transmission | Red | OFF | Not in use (No game linking) |
| (Note 2) | of data | ON | Sending data |
BLINKING Normal operation
| LED 8 | U14, Y1 | Audio activity | Yellow | OFF | No sound boot ROM |
| (Note 1) | ON | Locked up |
BLINKING Normal operation
| LED9 | U34, Y1 | Linking receiving data | Yellow | OFF | Not in use (No game linking) |
| (Note 2) | ON | Receiving data | |||
| LED10 | U44, Y2_ | Not used (Remains On) | Green | OFF |
(Note 1) ON BLINKING ~
| LED 11 | U44, Y2_ | Not used (Remains On) | Red | OFF |
(Note 1) ON BLINKING ~
| LED 12 | U44, Y2__| | Not used (Remains On) | Yellow | OFF | - |
| (Note 1) | ON | - |
BLINKING ~
| LED 13 | U44, Y2_ | Not used (Remains On) | Yellow | OFF | - |
| (Note 1) | ON | a |
BLINKING ~
Notes on SIO LED Indicator Status
- Software controls this LED. Indications are game and revision specific. Changing the EPROM’s on this board may alter the function of this LED. Firmware damage may also cause new or different LED behavior.
- Hardware controls this LED. Indications depend on hard-wired circuitry. A change in normal LED behavior may indicate a circuit fault. Changing the EPROM’s on this board shouldn't alter the function of this LED.
CHAPTER 5 WIRING
CPU BOARD LED INDICATOR STATUS TABLE
Device Location Function Color State Meaning
| LED 1 | U6, U7, U16 | 3.3V CPU Power | Red | OFF | Insufficient power |
ON Power OK BLINKING | Power supply fault
| LED 2 | U28, PS | Disk Drive Activity | Green | OFF | Disk not in use |
ON Locked up disk BLINKING | Normal disk activity
| RP63 | U22, U26 | Indicator | Red | OFF* |
ON* See NOTE 3, below BLINKING*
Notes on LED Indicator Status
- LED 1 monitors CPU power (+3.3V). If this LED is off or blinking, investigate processor circuits. If other LED’s are off or blinking at the same time, check +5V circuits or the game power supply.
- LED 2 flashes when the hard disk is operating during game play. LED 2 may light continuously during start-up. If this LED remains lighted, the hard drive may be locked-up or faulty.
- Software controls RP63. In this game, RP63 initially indicates program start-up stages. This LED is a seven-segment, alphanumeric display device. Normally, RP63 will display a lowercase “b” or “o” pattern with sequentially blinking segments. During Self-Test screens, RP63 displays a “bouncing bar” that resembles a hypen (“-”).
10 MiDway AMUSEMENT GAMES, LLC
CHAPTER SIX
TROUBLESHOOTING
A
Before servicing electronics, turn off AC power to the VGM. Wait for capacitors to discharge. Before touching or handling electronic assemblies, discharge static electricity on your body. To discharge static, begin by connecting the line cord to a properly grounded outlet, but do not turn on the power! Next, touch the safety ground stud of the power supply chassis. Store electronic assemblies in an anti-static area. Use anti-static bags to store or transport circuit boards. Transport the hard drive in original shipping container. Do not remove or connect electronic assemblies when the power to the cabinet is switched on. Otherwise you'll damage electronic assemblies and void the warranty. Replace ground wires, shields, safety covers, etc., upon completion of maintenance or service. Install and firmly tighten all ground and mounting screws.
COIN MECHANISM AND PRICING TROUBLESHOOTING
Symptom Cause Required Action
+ Video Game Machine (VGM) accepts currency or tokens, but number of credits per coin or bill is incorrect. Improper settings at Pricing Menu 1. Press and hold TEST MODE switch inside coin door to enter Menu System. Select SWITCH TEST from Diagnostics menu. Conduct test to confirm operation of game switches. Select either the STANDARD or CUSTOM PRIC- ING MENU from Game Adjustments Menu.
Faulty wiring Confirm cabinet wiring is correct for this game. Assure coin meter and coin switches connect properly to control input wires.
VGM will not accept currency or tokens.
VGM will not enter play mode.
Audio and video are present. Improper currency Unlock and open cash door. Empty cash box and inspect revenue for counterfeit currency. Check vault. Remove any items that block path from mechanism.
Faulty coin mechanism POV Unlock and open coin door. Check each mechanism for proper mounting. Remove mechanism. Clear currency path. Reinstall mechanism and close latch.
Tilted coin mechanism or game yo Verify mechanism is level after doors close. Repair or replace coin door if it is bent or damaged. If necessary, adjust cabinet leg levelers to keep mechanisms level.
Coin indicators do not light Burned-out bulb Burned-out bulbs may appear white or darkened. Check continuity with digital voltmeter. Replace burned-out bulb with an identically rated part.
Open fuse circuit Check fuse continuity with digital voltmeter. If fuse is blown, replace fuse with an identically rated part. If fuse isn’t blown, check wiring.
TROUBLESHOOTING - 2 MIDWAY AMUSEMENT GAMES, LLC
START UP TROUBLESHOOTING
| Symptom | Cause | Required Action |
| + Video Game Machine | Power problem | 1. | Check power is switched on. |
| (VGM) does not start. | 2. | Make sure fans are turning. If not: Is the power |
supply connected to its power cable? Is power + VGM appears com- supply turned on?
| pletely non-functional. | 3. | Plug cord into AC power outlet. Verify presence of |
AC line voltage. No audio Improper line volt- Turn off power. Unplug AC line cord. Check line age switch setting voltage switch. If necessary, set it to agree with local AC line voltage. Retest game. No illumination
| No video display | Open fuse | 1. | Turn off power. Examine AC fuse on power chas- |
sis.
- Examine DC fuses on cabinet wall or electronic equipment shelf.
- Replace faulty fuses with identically rated parts.
- Turn on game power. If fuse opens again, check DC wiring harness and connectors.
| Faulty wiring | 1. | Remove line cord. Test line cord, power plug, and |
IEC connector for breaks or damage. Verify continuity of each wire in cord. Install cord on power chassis. Press connector firmly to seat it.
- Assure that cabinet wiring harness connectors fully seat in corresponding power supply and board connectors.
- Inspect wiring for breaks or damage. Video Game Machine _ | Faulty coinmech- | 1. Unlock and open coin door. Check each currency
| (VGM) does not start. | | anism | acceptor to assure proper mounting. Verify each |
release latch is closed and locked.
| + VGM accepts cur- | 2. | Test mechanism with good and bad coins to see if |
rency or tokens. mechanism accepts and rejects currency correctly.
| + Audio and video are | 3. | Inspect to see if external acceptor indicators (Pric- |
present. ing, Flashing Arrows, etc.) are lit.
- Verify each acceptor operates properly by placing it in working game. Replace bad parts.
| Faulty switches | 1. | Press and hold the TEST MODE switch inside |
coin door to enter Menu System. Select SWITCH TESTS from the Diagnostics Menu. Conduct test to confirm operation of each switch.
- Assure no loose parts or wires are caught in switch contacts.
- Check for continuity in each suspect switch connection (Common to Normally Open or Common to Normally Closed).
- Replace faulty switches (bent levers, broken actuators, etc.).
C.A.R.T. FURY TROUBLESHOOTING - 3
Symptom Cause Required Action
+ Video Game Machine (VGM) does not start.
+ VGM accepts currency or tokens.
+ Audio and video are present. Faulty wiring 1.
2. Assure no wires are caught in hinges, latches or switch contacts. Check wiring continuity from circuit board connectors to acceptors.
+ Video Game Machine (VGM) appears nonfunctional.
+ Currency acceptor
nated. price indicator is illumi- Power problem Inspect circuit boards under low-light conditions. The LED’s glow and the fan turns when processor circuits receive voltage and indicate presence of DC from power supply. However, voltages or signals may not be normal. Turn on power. Set the digital voltmeter to the 20volt DC setting and measure DC voltages at power connector pins. Adjust the +5V source if necessary. Refer to the Cabinet Wiring Diagram for specific wiring information and voltage limits. Set the digital voltmeter to the 2-volt AC setting and measure DC voltages at power connector pins. Any reading here indicates that supply voltages are unstable and may contain ripple or noise.
Faulty wiring Turn off power. Check wiring harness connectors attach and fully seat onto mating board connectors. Verify harness connects to CPU Board. Check other connectors in same way.
Improper DIP switch settings Check DIP switch settings.
Faulty circuit boards Run power-up self-test sequence. Note errors or failures during test. Compare LED’s with LED indicator status charts. Note discrepancies. Press and hold TEST MODE switch inside coin door to enter Menu System. Select MONITOR TEST from Diagnostics Menu. Conduct test to confirm operation of each screen used in the game.
TROUBLESHOOTING - 4 MIDWAY AMUSEMENT GAMES, LLC
LINKING PROBLEM TROUBLESHOOTING
| Symptom | Cause | Required Action |
| * Cannot connect multi- | Faulty wiring | 1. | Do not extend linking cables supplied with VGM. |
| ple Video Game | 2. | Install required crossover between cabinets. Each |
Machines (VGMs) coupler connects two VGMs (one pair). Do not use together standard telephone type couplers or wiring for linking.
- Use only 10 Base-T, Ethernet-type, Category 5, twisted-pair wiring.
| Improper linking | 1. | Use required network hub for your local network. |
hardware A Hub Link Kit permits up to four VGM connections. Array completion requires basic kit brackets and spacers.
+ VGM does not recog- | Improper settings | 1. Record any error messages that occur during selfnize other players in test.
| linking operation | 2. | From the Diagnostic Menu select DIP SWITCH |
TEST. Confirm the link is enabled.
| + VGM functions nor- | 3. | Be sure that each VGM has a unique ID number. |
| mally by itself | 4. | Select LINKING TEST from the Diagnostic menu. |
Run tests for each linked VGM.
| Power problem | 1. | Verify the hub receives power. AC adapter wires |
are thin and easily damaged.
| Faulty wiring | 1. | Inspect hub indicator lights. Illuminated indicator |
(3 or more VGMs) lights for each active port light up if the cable(s) are properly connected. Check for cable continuity from hub to VGM for each indicator that failed to light.
- Assure no loose wires are caught in hinges, doors or under cabinet.
- Verify linking cable connects to CPU Board for each game.
- Verify each linking cable operates properly by placing it in working game.
C.A.R.T. FURY TROUBLESHOOTING - 5
LINKING PROBLEM TROUBLESHOOTING
Symptom Cause Required Action
+ Some Video Game Machines (VGMs) in group link properly, while others do not Improper hub switch setting 1. Assure switches on hub are set according to Hub Link Kit instructions. (VGMs on a network do not require couplers. Hub has electronic crossover.) Inspect hub indicator lights for link activity. See manufacturer’s literature for diagnostics.
Wrong software version Verify all linked VGMs use same version of software. Error message “VERSION MISMATCH’ will appear if you try to link different versions. Contact your distributor.
Faulty wiring (2 VGMs) 1. Insert only the supplied crossover connection between coupled VGMs. Standard couplers appear identical to devices supplied with games, but do not include an internal crossover. Verify each linking crossover coupler operates properly by placing it in a working link between two VGMs.
Faulty wiring (3 or more VGMs) Use an additional crossover connector and cable to extend game or hub link connection. Two crossovers cancel each other out and results in same problem as no link crossover. Connect cables directly to hub. Do not use a crossover coupler and hub together in single network. Separate communications wiring from other wiring. Wires that must cross can only cross at right angles to limit noise pickup.
TROUBLESHOOTING - 6 MIDWAY AMUSEMENT GAMES, LLC
PLAYER CONTROL TROUBLESHOOTING
Symptom Cause Required Action
+ Intermittent or completely non-functional player controls
+ Video Game Machine (VGM) starts normally. Faulty switches or lamps 1. Press and hold TEST MODE switch inside coin door to enter Menu System. Select SWITCH TEST from Diagnostic Menu. Conduct tests to confirm switch operation. Press and hold TEST MODE switch inside coin door to enter Menu System. Select LAMP TEST from Diagnostic Menu. Conduct tests to confirm lamp operation. Check for loose parts or wires caught in switch contacts. Check continuity at each switch connection (Common to Normally Open or Common to Normally Closed). Verify player control operates properly by placing it in working VGM. Verify light bulbs used for dashboard switches are type specified in parts listing. Other types will light, but may produce too much heat. Excess heat may cause switches to bind.
Faulty switch wiring Check for wires caught in door hinges, latches, or switch contacts. Verify harness connectors are attached and fully seated. Assure control switches connect properly to control input wires. Check cabinet wiring is correct for this VGM.
+ Steering pulls to one side Faulty Wheel Driver Board Find power amp on Wheel Driver Board’s large heatsink. Test and replace bad part or board.
+ No wheel feedback
- Steering aims vehicle as expected Improperly set feedback Select STEERING WHEEL TEST on the Diagnostics Menu. Set feedback to match player requirements. Maximum force may be too extreme for very young or inexperienced customers.
Faulty circuit Examine fuses and cables on Wheel Driver Board. Check cables and wiring between CPU board, wheel driver and motor. Check resistance of motor series resistors. Replace bad parts.
Faulty motor Turn off power. Open dashboard. Support steering wheel and remove outer mounting screws. Remove metal shield (if VGM has one) over motor. Unscrew caps. Inspect motor brushes. Replace worn parts.
TROUBLESHOOTING - 7
Symptom Cause Required Action
+ Sloppy, unpredictable or ineffective steering
+ Video is present
+ Video Game Machine (VGM) operates normally Blocked or faulty fan Fan located on power supply functions as an exhaust fan. With power on, check airflow near each fan to assure that nothing blocks airflow.
Faulty mechani- Turn off power. Open dashboard. Support steering cal parts wheel and remove outer mounting screws. Remove metal shield (if VGM has one) over motor. Inspect for faulty or worn belts, bearings, couplings, gears, etc.
Faulty Wheel 1. Inspect Wheel Driver Board under low-light condi- Driver Board tions. To indicate presence of AC from the transformer the LED’s glow when voltage is received. However, voltages or signals may not be normal.
- Examine fuses and cables on Wheel Driver Board. Replace bad fuses. Use digital voltmeter to verify AC voltage between each fuse holder and ground. You should measure approximately 25V. See Wiring Diagram.
- Use the 20-VAC setting on digital voltmeter to measure DC voltage at motor. Do not move steering wheel, drive belt, or motor while making this measurement. Any reading indicates unstable supply that may contain ripple or noise.
- Select the STEERING WHEEL TEST from the Diagnostic Menu. Follow on-screen instructions to verify operation of the wheel motor and steering position sensor.
- Verify proper operation of Wheel Driver Board by placing it in working VGM.
Loose or worn drive belt
- Turn off power. Open dashboard. Support steering wheel and remove outer mounting screws. Remove metal shield (if VGM has one) over motor. Inspect for faulty or worn belts, bearings, couplings, gears, etc.
- If drive belt isn’t worn or damaged, check its tightness.
Inability to make a transmission selection.
Video Game Machine (VGM) operates normally. Improper DIP Switch setting(s) From the Diagnostics Menu, choose DIP SWITCH TEST. Make sure DIP 1, SW 1 is set to the OFF position.
TROUBLESHOOTING - 8 MIDWAY AMUSEMENT GAMES, LLC
VIDEO TROUBLESHOOTING
| Symptom | Cause | Required Action |
| + Monitor appears non- | Power problem | Verify connection of AC Power to video monitor. Inspect |
functional neck of CRT in dim light. Glowing filament near CRT base confirms monitor circuits receive power. However, voltages + Audio is present or signals may not be normal.
| Faulty wiring | 1. | Turn off game power. Verify that video signal and |
+ Video Game Machine (VGM) controls oper- Remote Adjustment Board connectors seat properly on Video Monitor Board. ate normally 2. Assure that no wires are caught on chassis or
mounting brackets.
Improper monitor | Check BRIGHTNESS (intensity) and CONTRAST are adjustments set above their minimum levels. Faulty monitor cir- | 1. Examine AC line fuse on Video Monitor Board. If cuitry fuse is faulty, replace it with an identically rated fuse.
- If the fuse is good, verify video monitor operates correctly by placing it in a working VGM.
- If monitor is bad; Check monitor power supply.
- |f the power supply is good, Check monitor horizontal output transistor and related circuitry.
| + Graphic images from | Improper compo- | 1. | Verify circuit boards are correct for this game. |
game do not appear nents Labels on each board record manufacturers’ name, assembly number and hardware version.
| + No audio | 2. | Verify ROM instruction set is correct for this game. |
Game set includes more than one ROM. Label on + Power-up self-test each ROM records assembly number and softruns ware version.
| Faulty Circuit | 1. | Allow game to load normally. Note and record any |
Board error messages that occur during self-test.
- Press and hold TEST MODE switch inside coin door to enter Menu System. Select Diagnostic Menu from the Main Menu. Then select CPU BOARD TEST. Conduct this test to check operation of critical components.
- Turn off power. Inspect CPU Board to ensure JAMMA cable connector is fully seated onto the mating edge connector of the CPU. Check all other cable connectors for correct alignment and continuity.
- Compare activity of LED’s on CPU with the CPU Indicator Chart.
C.A.R.T. FURY TROUBLESHOOTING - 9
Symptom Cause Required Action
Power Problems
- Turn on Power. Use 20-volt DC setting on digital voltmeter to measure DC voltages present at Power connector pins. Verify +5V source if it is adjustable. Refer to Cabinet Wiring Diagram for specific wiring information and voltage limits.
- Use 2-Volt AC setting on digital voltmeter to measure DC voltages at Power Connector pins. Any reading indicates the supply voltages are unstable and may contain ripple or noise.
+ White areas at screen edges appear tinged with color Picture tube dynamic convergence is out of Have service bureau dynamically re-converge monitor. This procedure requires removing and repositioning yoke. Service bureau must follow instructions from alignment monitor manufacturer. + Dots at screen edges appear ovoid or cylindrical
+ Video images tear or | Faulty wiring 1. Check connectors and cables for wiring continuity. roll, or have black bar down middle of screen Video cables connect circuit boards to video monitor.
- Assure connection of all cabinet ground wires, especially at video monitor chassis.
Faulty monitor circuitry
- Verify video monitor operates correctly by connecting it to working Video Game Machine (VGM).
- Assure video monitor is correct type for this game. Video monitors with wrong resolution can’t lock sync.
Improper sync signals
- Check to see if Video Board puts out type of sync that your monitor requires.
- Verify jumpers are set correctly for monitor.
Electromagnetic fields Move cabinet far away from machines, appliances, or competitors’ video games.
+ Missing colors Faulty wiring Check connectors and cables for wiring continuity from circuit boards to video monitor.
Faulty monitor color drive circuitry Verify video monitor operates correctly by connecting it to working Video Game Machine (VGM).
+ One color is dimmer or brighter than others
+ Whites appear tinted everywhere on screen Maladjusted color bias pots Turn on Video Game Machine (VGM). From Diagnostic Menu select MONITOR TEST. Watch Color Bars screen in mirror. Adjust three bias pots for best colors. (Most monitor neck boards include these pots.) Check White Screen. Touch up controls. If whites still seem tinted, have service bureau rejuvenate picture tube. PONS
On
TROUBLESHOOTING - 10 MIDWAY AMUSEMENT GAMES, LLC
Symptom Cause Required Action
+ Picture is too narrow Maladjusted WIDTH pot. From Diagnostic Menu select MONITOR TEST. Watch Crosshatch Screen while adjusting WIDTH pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.
Picture is too short Maladjusted HEIGHT pot or damaged vertical circuit
- From Diagnostic Menu select MONITOR TEST. Watch Crosshatch Screen while adjusting HEIGHT pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.
- If pot has no effect, service vertical output circuit.
Picture seems shifted to one side Maladjusted HORIZONTAL POSITION pot From Diagnostic Menu select MONITOR TEST. Watch Crosshatch Screen while adjusting HORIZONTAL POSITION pot for best picture. You'll find this pot on Monitor Remote Control Board, behind coin door.
Keystone-shaped picture Shorted turns in yoke
- Substitute working yoke.
- Have service bureau converge monitor.
- Retest monitor.
Blotches of color appear on screen Picture tube aperture mask is magnetized Demagnetize monitor with external degaussing coil. Take care not to magnetize neighboring games. Monitor may be left on or off during this procedure.
White areas in center of screen appear tinged with color
Object edges have fringe of one or more colors Picture tube purity or static convergence is out of alignment
- Turn on Video Game Machine (VGM).
- Press and hold TEST MODE to enter Menu System. Select Diagnostic Menu from the Main Menu. Select MONITOR TEST. Perform tests for Crosshatch, Red, Green and Blue screens to find clearest display of problem.
- Display screen with the most severe problem.
- Display Crosshatch Screen. Locate purity and static convergence ring magnets on back of monitor neck. Watch screen in mirror. Adjust magnets to minimize problem. Follow instructions from monitor manufacturer.
- Display Crosshatch Screen. Touch up adjustments while watching screen in mirror.
+ Picture is dim or faded Maladjusted BRIGHTNESS pot or subnormal picture tube emission
- From Diagnostic Menu select MONITOR TEST. Watch Color Bars screen. Adjust BRIGHTNESS and CONTRAST pots for greatest number of grays. You'll find these pots on Monitor Remote Control Board, behind coin door.
- If pots have no effect, have service bureau rejuvenate picture tube.
TROUBLESHOOTING - 11
TYPICAL CUTAWAY REAR VIEW
A
TROUBLESHOOTING - 12 MIDWAY AMUSEMENT GAMES, LLC
AUDIO TROUBLESHOOTING
Symptom Cause Required Action
+ No audio
+ Video is present
+ Video Game Machine (VGM) appears to operate normally Improper volume setting Press and hold TEST MODE switch inside coin door to enter Menu System. Select VOLUME MENU from the Main Menu. Make sure the Attract Music is on (enabled). Verify all volume levels are set well above zero. If necessary, change levels to make game audible.
Faulty wiring Turn off power. Assure wiring harness connectors attach and fully seat onto mating board connectors. Verify harness connects to CPU Board. Check audio cable connectors in same way.
Faulty or Remove grilles and inspect speakers. Free speaker obstructed cones, terminals, mounting screws and magnets of speaker loose parts or wires.
Faulty Audio Verify proper operation of Audio Board by placing it in Board a working VGM.
Power Problems Use 20-volt DC setting on digital voltmeter to measure DC voltages present at Power connector pins. Verify +5V, -5V and +12V sources. Refer to Cabinet Wiring Diagram for specific wiring information and voltage limits.
+ Audio is distorted, muffled or has missing frequencies. Faulty or improper speaker
- Turn off power. Remove grilles and check speakers. Verify that speakers are full range (100 to 10,000 Hz response) and rated for at least 20 watts. Woofers must be rated for at least 40 watts.
- Verify proper speaker operation by placing speaker in question in a working VGM.
Faulty wiring Multiple-speaker installations: Check for reversed wires at one speaker. Weak or low frequencies and thin or hollow sound quality are symptom of incorrectly phased speakers. Sound tests may not detect this condition, but you can hear it during operation.
Improper Setting Press and hold TEST MODE switch inside coin door to enter Menu System. Select SOUND TEST from Diagnostics Menu. Increase volume as required. This test will verify some audio circuit functions.
+ Dead sound channel Faulty speaker
- From Diagnostics Menu, choose SOUND TEST. Recheck speakers with audio signals provided by test.
- Verify proper speaker operation by connecting speaker in question to working Video Game Machine (VGM).
TROUBLESHOOTING - 13
Symptom Cause Required Action
Faulty circuit Run power-up self-test sequence. Note errors found board during tests. Compare CPU Board LED’s with LED Indicator Status Charts. Note discrepancies.
- Constant low hum Faulty wiring 1. Check cabinet wiring is correct. from all speakers.
- Verify cabinet wiring provides separate wires (not common return) for each speaker.
- Check connection of all cabinet ground wires.
Faulty power supply Use 2-Volt AC setting on digital voltmeter to measure voltages at speaker terminals. Any reading indicates unstable supply that may contain ripple or noise.
MISCELLANEOUS PROBLEM TROUBLESHOOTING
Symptom Cause Required Action
+ Marquee lamp is intermittent or non-functional
Video Game Machine (VGM) starts and plays normally Faulty fluorescent tube
- Remove fluorescent tube from sockets. If you find cracks or darkened ends, install new lamp. Clean tube.
- Check continuity of both fluorescent tube filaments.
- Check lamp ballast is rated for local AC line voltage and frequency.
- Verify fluorescent tube operates by placing it in working VGM.
Faulty lamp fixture
- Verify lamp pins make good connection with socket contacts.
- Check the ballast and/or starter are working properly.
Faulty wiring Measure fluorescent lamp AC voltages. Check wiring and connector continuity from AC power chassis to lamp assembly.
VGM operates normally
Cabinet becomes warm after several hours of use Obstructed fan
- Check bottom and rear of cabinet for blocked airflow.
- Move VGM away from sources of heat.
- Turn off power. Remove dust from vent holes with high-power vacuum cleaner.
Faulty Wiring Check fan wiring and connectors.
Faulty fan Check operation of all fans.
Error messages appear on screen Faulty hardware
- Check any assembly (RAM, ROM, Battery, etc.) identified in error messages.
- Call your authorized distributor for help with unresolved screen messages.
TROUBLESHOOTING - 14 MIDWAY AMUSEMENT GAMES, LLC
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
WARNINGS & NOTICES
If you or anyone in your family has experienced symptoms linked to an epileptic condition (e.g. seizures or loss of awareness), immediately consult your physician before using any video games.
We recommend that parents observe their children while they play video games. If you or your child experience the following symptoms: dizziness, altered vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation, or convulsions, discontinue use immediately and consult your physician.
COPYRIGHT & TRADEMARK NOTICE You may not reproduce any part of this publication by mechanical, photographic, or electronic means. You may not prepare phonograph recordings of this document. You may not transmit this publication or otherwise copy it for public or private use, without permission from the publisher.
CART FURY © 2000 Midway Amusement Games, LLC. MIDWAY and the M IN A CIRCLE DESIGN are trademarks of Midway Amusement Games, LLC. © 1999 Official Licensed Product of Championship Auto Racing Teams, Inc. All logos and marks of CART, its Teams, Drivers, Tracks and sponsors, are the property of CART and its respective Teams, Drivers, Tracks and sponsors and may not be reproduced, in whole or part, without the prior written consent of CART Licensed Products, Inc.
NOTICE This equipment generated, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interferance to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
NOTICE When Midway Amusement Games, LLC ships a VGM, it complies with FCC regulations. Your label is proof of compliance. Legal repercussions to the owner or distributor may result if the label is missing or damaged. If your VGM does. not contain an FCC compliance label, call Midway Amusement Games, LLC immediately.
For Service:Call your authorized Midway Amusement Games, LLC distributor.
MIDWAY AMUSEMENT GAMES, LLC 3401 N. CALIFORNIA AVE. CHICAGO, ILLINOIS 60618-5899 USA Visit our Web site at http:/www.midway.com
Entire contents of this manual copyright © 2000 Mipway AMUSEMENT GAMES, LLC . All rights reserved.