Golden Axe Installation Owners Manual (4200005U)
Golden Axe (set 6, US) (8751 317-123A) (Sega, 1989) · Owner's Manual · 26 pages · 14 sections · original scan
P= | : > + pr S& ~s Poesy Installation/Owners Manual
This SEGA product has the copyright notice as follows: OSEGA 1989
This signifies that this product was disclosed in 1989 and is the property of SEGA Enterprises.
by:
SEGA Enterprises, Inc. (U.S.A.) 2149 Paragon Drive San Jose, California 95131 Phone Number (408) 435-0201 FAX Number (408) 435-0294
The Federal Communication Commission requires the verification of game kits. This game kit will meet these requirements when installed in accordance with the instructions in this Manual and using only components and materials supplied with this kit.
Table of Contents
Introduction 2.2.0.2... eee Handling and Installation Precautions ....... Prevention of Counterfeiting and Conversion Labeling. . Precautions Concerning the Place of Installation . . System Requirements ........ beeen Le Tools Required .............. cece cece e tree eee Cabinet Preparation . fee Le wae Kit Component Verification................ Installation Procedure ... . veces . Monitor Bezel .... . beets License Seal ...... . Side Decal . Marquee Plex ....... beeen Control Panel . bcc Service Switch ‘Assembly . Harness Installation ....... Interface Harness Installation . cee Cabinet 115 VAC System Grounding bee Cabinet System Checkout .... : Golden Axe Printed Circuit Board Installation Logic Board and Complete System Checkout In Case of Difficulty... 0.0... Figure | _ Figure2 . Figure3 .. Figure4 .. Figure5 . Figure 6 Figure7 . Figure 8 . Figure 9 Figure 10 gt ures eeaga ft Figure loo. beeen Figure 12 . : Figure 13 .... Switch Setting Sheet : : Schematic Diagram bees
Introduction
Handling and Installation Precautions
During installation:
Prevention of Counterfeiting and Conversion Labeling
Precautions Concerning the Place of Installation SEGA ENTERPRISES, LTD., supported by its high electronic technology of Large Scale Integration, microprocessors, etc. and a wealth of experience, has for more than 30 years been supplying various innovative and popular game machines to the world market. This OWNER’S AND KIT INSTALLATION manual is intended to provide detailed comments together with all the neccessary information covering the operation and installation of electronic assemblies, electromechanical assemblies, control assemblies, and spare or replacement parts for the GOLDEN AXE coin operated game. This manual is intended for those who have knowledge of electricity and technical expertise in video games. Carefully read the enclosed information before starting the kit installation or troubleshooting procedures.
- Be sure to remove power plug when working on the machine
- Be sure all connections and harness routing are secure.
- Make sure all grounding connections are secure and properly affixed
- Do not use any fuse that does not meet the specified rating.
To prevent counterfeit and unauthorized conversions, the following label is supplied with all authorized SEGA kit products. When handling such goods, be sure to locate and confirm the label. It is used to prevent illegal acts such as the unauthorized copying of the products and the printed circuit boards.
e SEGA’ AU DF NE ORIGINAL SEAL THIS PRODUCT IS DESIGNED F ‘AND MANUFACTURED BY SEGAENTERPRISESLTD. LICENSE # GOLDEN AXE ano. 16391
- SEGAENTEAPRISES, LTD. 4 ‘JAPAN t t t t +
The GOLDEN AXE CONVERSION KIT is intended to be installed in an indoor game cabinet. Absolutely do not install it outdoors. When installed indoors the following places mentioned below should be avoided to ensure proper operation and usage:
Places subject to rain or water leakage, or condensation due to humidity In the proximity of an indoor swimming pool and/or shower Places subject to direct sunlight Places subject to heat sources from heating units, hot air, etc. Vicinity of highly flammable/volatile chemicals or hazardous materials Sloped surfaces Vicinity of anti-disaster facilities such as fire exits and fire extinguishers Places subject to any type of violent impact Dusty environment
System Requirements
Power Supply:
RFI Line Filter:
Miscellaneous: « Input voltage 90 VAC to 135 VAC 60 Hz « +5 volts at 6 amps « +12 volts at 2 amps
- Overvoltage protected at +5.8 volts
- Current limit set at 8 amps
- If a switching power supply is used:
- Current rating of 6 amps
- Frequency attenuation of the following: -1I5MHz 40db .5MHz 65db 1OMHz 65db 5.0MHz 55db 10.0MHz 50db 30.0MHz 50db
- If a linear power supply is used:
- Current rating of 5 amps
- Frequency attenuation of the following: .ISMHz — 6db .5SMHz 19db 1OMHz 28db 5.0MHz 42db 10.0MHz 45db 30.0 MHz 50db
Line Fuse: 4. amp 120 VAC Speaker: 8 ohms 10 watt On/Off Switch: 6 amp 120 VAC Isolation Transformer: 115 VAC primary, 115 VAC secondary, 100 watts Coin Door: Dual coin acceptors Coin Meter: +5 Volt DC Power Cord: Three conductor with ground Color Monitor:
Video input | volt to 5 volt peak-to-peak positive polarity Sync TTL negative polarity separate horizontal and vertical Horizontal frequency 15.750 KHz Vertical frequency 60 Hz Video bandwidth 12MHz or greater Horizontal mounted Recommended size 19 inch
Tools Required
Cabinet Preparation Drill Hole cutter 1-3/16” Phillips screw driver Flat blade screw driver Small flat blade screw driver Scissors Sand paper Paint X-acto knife Wood patch
RwWNn-
ww . Remove old PCB, and all existing game harnesses. . Remove and disassemble the control panel. Remove any side decals, monitor bezel, and marquee. . Using sandpaper and/or paint thinner, clean and smooth the cabinet for paint preparation. Use wood patch to fill any knicks or flaws in the cabinet. . Paint cabinet if required. . Wipe down and vacuum cabinet as necessary.
Kit Component Verification
Verify each component with the kit list provided to assure your kit is complete. If any part is missing after the inventory is taken, please contact your distributor, and provide to them the following information:
- Kit serial number
- Part number and description of missing item/s
- Date received
Kit List Part Number Quantity Description
| 0002-0000 | 2 | #6 x 3/8 Pih Phil Tek |
| 0002-0001 | 4 | #6 x 3/4 PIH Phil “AB” SMS |
| 0312-0024 | 8 | #10-24 x | 3/4 Carr/Bolt Black |
| 0502-0024 | 8 | #10-24 Hexnut |
| 0612-0024 | 8 | #10 Split Lock Washer |
| 0692-0024 | 8 | #10 Flat Washer 1/2 OD |
| 2112-0000 | 2 | Wire Nut #18 x 2 |
| 252-0005U | I | Monitor Bezel Golden Axe |
| 420-0005U | | | Manual Golden Axe |
| 421-5801-95 | 1 | License Seal Golden Axe |
| 421-7442 | 1 | Switch Setting Sheet |
| 4212-0001 | i | (Kit) Serial # Sticker |
| 423-0033U | 1 | Golden Axe Marquee Plex |
| 423-0032U-A | 2 | Side Decal, Sword |
| 423-0032U-B | 2 | Side Decal, Axe |
| 423-0032U-C | 2 | Side Decal, Golden Axe |
| 4231-0007 | 1 | Golden Axe Control Panel Overlay |
| 4231-0008 | 1 | Control Panel Clear Plex |
| 423-0031U | 1 | Golden Axe Label Sheet (See List) |
- Test, Service, Volume Sticker
- Joystick Stickers
- Attack Stickers
- Jump Stickers
- Magic Stickers
- Start 1 Player Sticker
- Start 2 Player Sticker
- FCC Sticker (Kit)
| 4750-0049 | 1 | Volume Control 100 Ohm 10 Watt |
| 5090-5028 | 2 | PB Spst Switch Momentary |
| 5091-0001-01 | 2 | Joy Stick 8 Way (Spring Type) |
| 5091-0004-01 | 2 | PB Spst Control Panel (Red) |
| 5091-0004-02 | 2 | PB Spst Control Panel (White) |
| 5091-0004-03 | 2 | PB Spst Control Panel (Blue) |
| 5091-0004-04 | 2 | PB Spst Control Panel (Yellow) |
| 6010-0043 | 1 | Knob, '/s” Shaft |
| 833-7001-02 | 1 | Golden Axe Game—PCB |
| 9992-0000, | 6 | 4" Tie Wrap |
| KRO-1721 | 1 | Service Switch Bracket |
| JAM-0000 | i | JAMMA HARNESS. |
| $25-0002U | | | SEGA to JAMMA I/F HARNESS, |
| 5091-001 5-01 | 8 | Pal Nut |
| 5091-001 5-02 | 8 | Leaf Switch |
| 5091-001 5-03 | 8 | Universal Adaptor |
Installation Procedure
Monitor Bezel
License Seal
Side Decal
Marquee Plex
Control Panel Locate MONITOR BEZEL (252-0005U). Measure the size of existing monitor bezel or the required size to fit and cut cardboard monitor bezel to size. (see figure 1)
Locate GOLDEN AXE LICENSE SEAL (421-5801-95) and place seal as shown of in figure 1. Install Monitor Bezel on game cabinet. Note: Verify that the License Seal will be visible when the bezel is installed on game cabinet.
Locate GOLDEN AXE SIDE ART (423-0032U). Install on the left and right side panels of the cabinet (see figure 1). Note: A mixture of slightly soapy water can be used on the cabinet to position the artwork as desired. A squeegee may be used to remove any wrinkles in the artwork if soapy water is used
Locate GOLDEN AXE MARQUEE PLEX (423-0033U). Measure the size of existing marquee plex or required size to fit and trim the marquee plex to size, Install on cabinet. (see figure 1)
Locate GOLDEN AXE CONTROL PANEL OVERLAY (4231-0007). Measure the size required and cut the control panel overlay to fit the existing control panel.
Define the location of the player push buttons and joystick(s) on the control panel. (see figure 2)
Cut holes in control panel to locate buttons and joysticks). See template for button and joystick. (see figure 3)
Install the “ONE PLAYER START” label and the “TWO PLAYER START” label on the control panel overlay. (see figure 2)
Install player control button labels, MAGIC, ATTACK and JUMP on the control panel overlay. (see figure 2)
Install the JOYSTICK label(s) on the control panel overlay. (see figure 2)
Locate the CONTROL PANEL CLEAR PLEX (4231-0008) and cut holes into the plex to match the holes cut into the control panel. Then trim as required to protect the control panel overlay and labels. Note: this clear plex overlay can be used to protect unused holes in the control panel from player punctures. (see figure 2)
Install YELLOW buttons (5091-0004-04) in the “MAGIC” locations. (see figure 2)
Install RED buttons (5091-0004-01) in the “ATTACK” locations. (see figure 2)
14, Install BLUE buttons (5091-0004-03) in the “JUMP” locations. (see figure 2)
15, Install WHITE buttons (5091-0004-02) in | PLAYER START and 2 PLAYER START locations. (see figure 2)
- Locate the JOYSTICK(S) (5091-0001-01). This package consists of the following six components. a. Preassembled joystick(s) base assembly with microswitches b. E-ring c. Black knob & shaft d. 2” Dia. washer e. Actuator plastic f. Pivot cone
The final assembly of the joystick(s) must be performed after the joystick(s) base assembly is mounted on the control panel. Locate the following: a. #10-24 X | 3/4 Carr/Bolt Black (0312-0024) (8 ea) b. #10-24 Hexnut (0502-0024) (8 ea) c. #10 Flat Washer 1/2" OD (0692-0024) (8 ea) d. #10 Split Lock Washer (0612-0024) (8 ea) Use the above components to secure the Joystick base assembly to the control panel. (see figure 2)
The final assembly of the joystick(s) is performed by: a. Placing the 2” Dia. washer over the Black knob & shaft. b. Install the Pivot cone on the shaft. c. Install the Black knob & shaft assembly through the joystick(s) base assembly on the control panel. d. Install the Actuator micro/switch on the shaft. e. Install the E-ring on the shaft to secure the assembly.
Service Switch Assembly 17. Locate SERVICE SWITCH BRACKET (KRO-1721) and install two PUSH BUTTON SPST SWITCH MOMENTARY (5090-5028) into bracket as shown in figure 4.
- Locate VOLUME CONTROL 100 OHM 10 WATT (4750-0049) and install into service switch bracket as shown in figure 4.
- Locate TEST, SERVICE, VOLUME STICKER and place on the service switch bracket as shown in figure 4.
Harness Installation 20.
21.
22.
24. Locate KNOB 1/8” SHAFT (6010-0043) and install on shaft of volume control 100 ohm 10 watt as shown in figure 4.
Install the Service Switch Assembly using 2 ea #6 x 3/8 P/H PHIL TEK screws (0002-0000) in the cabinet at either of the following locations (see figure 5): + On top of the steel enclosure for the Cash Box. inside the coin door.
Locate the JAMMA HARNESS (JAM-0000) and install as shown in figure 5 Use the provided (6 ea) 4” TIE WRAP (9992-0000) to secure the harness.
Connect the harness to the POWER SUPPLY as follows: (see figure 6) a. +5 volt source. (Pins 3, 4, C, D of Jamma Harness) b. +12 volt source. (Pins 6, F of Jamma Harness) c. GND source. (Pins B, 27, e, 28, f of JAMMA HARNESS)
Connect the harness to the COIN DOOR as follows: (see figure 7.) a. Connect the wire to coin chute 2 acceptor microswitch COMMON terminal. (Pin T of Jamma) b. Connect the wire to coin chute | acceptor microswitch COMMON terminal. (Pin 16 of Jamma) c. Connect the wire to coin chute | and 2 acceptor microswitch NOR- MALLY OPEN terminal. (Pin A of JAMMA) d. Also connect Pin A JAMMA to one side of each lamp on the coin door. e. Connect 4:5 volts from the power supply to the other side of each lamp on the coin door.
Connect the harness to the COIN METER by using two WIRE NUTS (2112-0000). (see figure 8) Note: Some coin meters have an internal diode.
- Connect the harness to the CONTROL PANEL as follows
a. Route and connect the daisy chained wire to the terminal of the PLAYER PUSH BUTTONS and JOYSTICK as shown in figure 9. b. Connect the control panel harness wires as follows: (figure 10)
JAMMA PIN # TO PLAYER | JOYSTICK UP 18 TO PLAYER | JOYSTICK DOWN 19 TO PLAYER | JOYSTICK RIGHT 21 TO PLAYER | JOYSTICK LEFT 20 TO PLAYER | JUMP 23 TO PLAYER | ATTACK 22 TO PLAYER | MAGIC 24 TO PLAYER | START 17 TO PLAYER 2 JOYSTICK DOWN W TO PLAYER 2 JOYSTICK UP Vv TO PLAYER 2 JOYSTICK RIGHT Y TO PLAYER 2 JOYSTICK LEFT x TO PLAYER 2 JUMP a TO PLAYER 2 ATTACK Zz TO PLAYER 2 MAGIC b TO PLAYER 2 START U
- Connect the T.V. Monitor as shown in figure 11
- Connect the routed speaker wires to the speaker. Check the routing for security.
SEGA TOJAMMA Interface 29. Locate SEGA TO JAMMA INTERFACE HARNESS and connect by inserting Harness Installation the card edge into the JAMMA HARNESS matching arrows to assure proper orientation. (figure 13)
- Connect the SEGA TO JAMMA INTERFACE HARNESS to the SERVICE SWITCH ASSEMBLY as follows: (see figure 4.) a. Connect the two wires to a terminal of each (GND) PUSH BUTTON. I/F Harness Pin f. Connect the wires to the SERVICE SWITCH. I/F Harness Pin 23 Connect the wires to the TEST SWITCH. I/F Harness Pin 22. . Connect the wires to the terminal of the VOLUME CONTROL that is nearest the center of the bracket. I/F Harness Pin b: e. Connect the wires that go to the speaker to the center terminal of the VOLUME CONTROL. Jamma Harness Pin L. f. Connect the wire that is routed to the 56 pin connector to the outer most terminal of the VOLUME CONTROL. I/F Harness 24. ane
Cabinet 115 VAC 31. System Grounding
Cabinet System Checkout 32
33.
Golden Axe Printed 36. Circuit Board Installation
37.
Logic Boardand 39. Complete System Checkout Locate the GROUND lead (green) of the 115 volt input power Line (see figure 12). This must be connected to all components of the game system. This is a safety requirement for the players’ protection. This AC GROUND must be of #18 AWG wire or larger. (see figure 12 for the proper routing of the wire)
Apply power to cabinet system and check for the following voltages. If any voltage is incorrect, remove power and correct problem before proceeding any further. a. +5 Volts on pins 3,4.C, and D of the 56 pin PCB connector. (Interface Connector) b. +12 Volts on pins 5 and E of the 56 pin PCB connector. c. No voltage present on any other pins of the 56 pin PCB connector.
Check that the monitor has power. This can be accomplished by observing the glow of the filament inside the neck of the picture tube.
Check that the Marquee lamp has power.
Check that the system ON/OFF switch functions properly.
Locate the GOLDEN AXE GAME and install the logic PCB inside the cabinet (see figure 5). Use (4 ea) #6 x 3/4 P/H PHIL “AB” SMS (0002-0001) to secure the PCB through its’ mounting feet.
Locate the GOLDEN AXE SWITCH SETTING SHEET (421-7442). Place this sheet on the inside of the game so that it is visible when the back door is removed or opened. This will allow the DIP SWITCH OPTIONS to be handy when service or changes in options are required.
Connect the 56 pin connector of the Interface Harness to the PCB with the label on the same side as the components on the PCB. The 56 pin connector is marked with “COMPONENT SIDE”
. Apply power to the system and observe that the logic PCB functions. If a video picture is not present proceed to "IN CASE OF DIFFICULTY” portion of this manual. When corrected, return to this point and continue.
Press the TEST BUTTON to enter the test menu. Individual tests canbe = — entered by moving the Joystick. Press the test switch again to enter the test.
+ Memory test: Tests all main program Rom and Ram accessible by the main CPU. + Input test: Tests all player inputs. « Sound test: ‘Tests all sounds. Move the Joystick UP or DOWN to select Sound category and move RIGHT or LEFT to select individual sounds. Press AF TACK to test. + CRT test: Displays color bar and grid size so monitor adjustment can be made for color, focus, size, etc. + Dip switch test: Shows current Dip Switch settings. (Dip Switches may be changed in this mode with power on.)
- Back-up RAM clear: Enables erasure of all bookeeping information, high scores, etc. ° Exit: (Press test when arrow lines with this to exit to normal game mode.) + Bookkeeping: Shows all coin credit in data and displays high/low scores, etc.
Set up game options as shown in figure 14. _, a. DIP SWITCH | on PCB sets up the number of coins per credit b. DIP SWITCH 2 on PCB sets up the following: Advertise Sound - Set to ON -2on Game Difficulty - Set to NORMAL -3.4,5, 60ff
Functionally test the game by: a. VERIFY that coin drops register proper credit/s and the COIN METER OPERATES. b. VERIFY that the proper number of lives is given for each CREDIT. c. VERIFY that the JOYSTICK MOVES the player left, right, and down. d. VERIFY that each MAGIC BUTTON functions. e. VERIFY that each JUMP BUTTON functions f. VERIFY that each ATTACK BUTTON functions.
Locate the Kit SERIAL NUMBER STICKER and FCC STICKER. Install these stickers on the rear of the game cabinet. (see figure 1)
a |
In Case of Difficulty
—Check A.C. line cord —Check line fuse —Check monitor brightness —Check power switch and/or interlock switch ~Check all solder connections on line filter and transformer —Check for proper orientation of the 56 pin PCB connector
—Check all PCB to monitor connections —Check power supply voltage on PCB
—Check monitor brightness —Check all PCB to monitor connections
~Monitor needs degaussing -Check for proper wiring between PCB and monitor ~Check monitor adjustment and adjust if necessary
—Check monitor ground is properly connected to monitor —Be certain sync inputs are properly connected to monitor —Check horizontal hold adjustment
—Check horizontal and/or vertical hold adjustments —Check for proper wiring of sync from PCB to monitor
—Check volume control potentiometer adjustment —Check for + 12 volts on edge connector of PCB -Check wiring from PCB to speaker -Check speaker for low resistance between the “+” and “-—" tabs
—Check wiring to speaker for bad solder connections, ~Check sound with another speaker
—Check ground connection to switch/es ~Check wiring between PCB and switch/es for proper connection Check switch/es with an ohmeter to verify proper operation
-Check wiring between PCB and switches for proper orientation -Check wiring for shorts between switch inputs
-Check wiring to coin meter —Check that +5 volts is on "+" side of meter —Verify a +5 volt meter is used
-Verify that a meter with a diode is used —If no diode is built in meter a 1N4004 can be used across the meter. Cathode to “+” side of meter and anode to "—" side of meter
STICKERS (FOC/SER.#) MARQUEE PLEX
MONITOR BEZEL PS
ORIGINAL SEAL ‘I
SIDE ART SIDE ART
RIGHT LEFT
Figure |
JOY STICK ASSEMBLY BLACK KNOB & SHAFT
. PUSH BUTTON ASSEMBLY 7" DIA WASHER on eaen
CLEAR PLEX
PANEL OVERLAY == 8 pVOT CORN 4 \ Wag CONTROL PANEL ’ | ti L i FLAT WASHER eh) ay SPRING WASHER Le EF — perator mrs E-RING o a”
- > — RECOMMENDED PANEL LAYOUT
PLAYER 1 START ay \ - 2) MAGIC
ATTACK = JUMP PLAYER 2 START
ATTACK = JUMP
MAGIC.
\ ATTACK LL JUMP
Figure 2 \ MAGIC
i
ATTACK ~ JUMP
Figure 3
JAMMA L TO SPEAKER TO S6P b
TO SPEAKER TO 56P 24
TO S6P 22 TO 56P 23
TO 56P f
VOL CONT TEST ‘SERMCE
‘STICKER FOR SWITCH BRACKET
ASSEMBLY AND WIRING ON SWITCH BRACKET
Figure 4 ‘SERVICE SW 1.36"
TEST SW VOLUME CONT
Eer=
&
| foape) | ap | loape) |
o
| SERVICE | TEST | VOLUME |
| oO | Oo | 0 |
CONTROL PANEL ~
COINDOOR=—
SWITCH TS _,—~ GAME BOARD BRACKET
COIN werer——|_—. NZ
K POWER SUPPLY
SUGGESTED HARNESS ROUTING
Figure 5
TERMINAL LAYOUT MAY BE DIFFERENT ON YOUR POWER SUPPLY
Figure 6
(I
5 5 COIN CHUTE 2
©) LAMP {0 POWER SUPPLY + SV P 9
[®
COIN CHUTE 1
COM WIRING FOR COIN CHUTE DOOR : NO 1056p 16 (Jamma) TO 56P T (Jamma) TO 56P A (Jamma) Figure 7
A WIRE NUT
ell TO POWER SUPPLY +5V
COIN METER
CND TO 56P 8 (Jamma)
WIRING FOR COIN METER T
Figure 8
CONTROL PANEL REAR VIEW GROUND ROUTING
PLAYER 1 START.
PLAYER 1 JOYSTICK
Figure 9
CONTROL PANEL REAR VIEW
PLAYER 2 START SIGNAL ROUTING
Pin U Jamma—_ Pin 17 Jamma. MAGIC.
PLAYER 2 JOYSTIC MAGIC
re
Figure 10
JAMMA P.
N
COLOR MONITOR
aay
Figure 11
ly)
ISOLATION TRANSFORMER}
ly)
WIRING OF AC LINE GROUND
CONTROL PANEL
Figure 12
FLUORESCENT COLOR MONITOR POWER SUPPLY
UGHT
[COMPONENT SIDE] 3
SEGA TO JAMMA
I/F HARNESS
Figure 13
o~ Switch Setting Sheet Pili ASSIGNMENT-SEGA INTERFACE PIN ASSIGNMENT-JAMMA PIN-OUT
| ‘COMPONENT SIDE | ‘SOLDER SIDE | COMPONENT SIDE | ‘SOLDER SIDE | ||||
| cso | [7 | [aA] | ono | eno | [ipa] | oxo | |
| ‘GND | kd | B | GNO- | GND | 2 | B | GND |
| sv | [ote] | tsv | sv | [ale] | tv | ||
| +y | 4 | [0 | +v | +5 | a | [o | +8v |
| sav | [sole] | +a | oy | Pete} | -w | ||
| conmerens | [6 | F | | conmerer2 | eo | Pete] | sw | ||
| (NOTUSED) | L | ll | (NOT URED) | (NOT USED) | 7 | H | (NOT USED) |
| AR MAIC, | 7 | 2 | aPMNGIG | COIN METER 1 | 8 | J | COIN METER 2 |
| ae | ee | fame | contoccours | [3s | «| | contockoure |
° | « |
| a | oo | ore | SPEAKER (+) | T] | sPeaKer)- |
| wotuseo) | [x] | M] | wworuseo) | MONITOR | | | |
| AUDIOW+) | M] | —AUDIOGND) | |||
| rpoown | [@ | | N] | 2Ppown | mS | |
| ee | ETH | ope | VIDEO RED | N | viocoGreeN |
veux | |
| VIDEO BLUE | P| | viogosyne | |||
| wricHt | [aa | [a] | 2PricHr | ao | Pa |
VIDEO GN
| wort | [as | fs] | eptert | HORIZONTAL | ee | pay | |||
| worusen) | [ie | [1] | worusen) | ||||||
| con | T] | come | / | ||||||
| worusen) | [7 | [u] | worusen) | vont | TH] | Seema PLE / | |||
| wotusen) | [|v] | worusen) | lo Bie ye | s | 1 | (CHE? | |||
| worusen) | [79 [| w] | (notuseD) | BR (ue 1PUP | ev | aur BEF | LEE | |||
| con: | [20] | x] | 1stAr | pip feoom | Fe | Tw} | zr oun tele | fe | |
| cone | [afv | | 2smar | ER | [yaievert | [oo | [Tc] | amsert | wel 7 | |
| test | [ae | Pz] | worusen) | 2 | grace | [arp] | sain | ule | a |
| service | [2a] | a] | (woruseo) | pusn | [ze | [2] | 2prusis f, wack t | ||
| spcamen(s) | [eee] | (-)sPeaKen | (gitarmoons | Tafa] | ers | BUN | |||
| reo | [|e] | cacen | wbtrreusis | [ae | [oe | 2reusis 10 | ||||
| ewe | [2s | [ae] | cwpsync | preserveo | [2s | |<] | 2PRESeRVED | ||
| ono | far[e] | ono | wreseaveo | [26] | a] | 2PnesEAVED | |||
| ono | [eft] | ono | ono | [ae] | oxo | ||||
| ono | [ee | [+] | ono |
seP__P.93.96mm 56P__P.396mm
| COIN/CREDIT OPTION SWITCH SETTING | DIP Swat | 171-5358 | |
| [corre | T2727 | ]*15]*]7 | 1% |
| Toon | voneon | | arr | or | ovr | or | or | ovr | ovr | om | |
| ‘con | Zoneons | | on | or | OFF | or | ow | OFF | OFF | OFF | TYPE |
| ‘eon | aoneons | ort | on | OFF | ort | ort | Ow | oFF | oF | 2 | |
| 1 COIN | REDITS | ON | ON | OFF | OFF | ON | ON | OFF | OFF | B. |
recon Scneons — | om | Orr | on | ort | ovr | or | Ow | Orr yeonseneons — | ow | orr | on [ort | Ow | OFF | on | Orr acoms scneor” — | ovr | on | ow | ovr | ofr | Ov | On | OFF
| Scoms | 1 cneor | on | on | ov | or | On | on | on | oF | ||
| fcoms | teneor | | Orr | ort | orr | on | ort | ort | Orr | on | oo | |
| 2coms | screors | | on | ort | ofr | on | on | ofr | ort | on | 1 | 238 |
2cONS 1 CREDIT
| soos | 2creors | Tore | on | ore | on | or | on | ort | on | mt | Nn |
Scons 3cREDITS
| SCONS | _4CREDITS | DIP SW1 | ||
| 2coNs | 1 CREDIT | " | 7 | i” |
| scons | soneors | | ON | ON | OFF | | ON | oN | on | oFF | OW | DIP Sw2 |
"CON 1 CREDIT
| 2cons | 2GREDITS | | |
3eoms screprs — | or | orF | on | on | ofr | oF | on | on icons 3GREDITS | __SCOINS _ 6 CREDITS GAME OPTION SETTING DIP SW #2 "con 1cReDit
| 2cons | d¢ReDITs | 7]2]3]4]5]6]7]8 | |||||
| deans | Sereors | | o* ] or | om | fom | Jon | rr | on / on | SSE | = | |
| icon | chen | | | ” | ZCREDITS TO START | oN | ||
| 2cons | _screots | | OFF | ON | ON | on | oFF | on | on | ON | ADVERTISE | [OFF | ON | ||
| FREE PUN | on | Low | on | on | [on | ow | [on | ow | SOUND | ON | OFF |
| comswer | | | ___comsurwa | Gane | HARDEST | on | [om | on | or | |
| erreunry, | HARDER | ON | OFF | OFF | OFF | |||||
| tasoatects | [HARD | corr | [of | on | oFF | notuseo |
numberof
| payers) | NORMAL | corr | oFF | oFF | oFF |
easy corr | or | orr | on EASIGR ‘ofr | on | oF | orF EASIEST ‘off | on | oFF | ow
| SPECIAL | on | [ow | [on | on |
Schematic Design
SEGA Enterprises, Inc. (U.S.A.)
2149 Paragon Drive San Jose, California 95131 Phone Number (408) 435-0201 FAX Number (408) 435-0294 ’