CATHODE RAY TOMES

Killer Instinct (16-40047-101 Nov 1994)

Killer Instinct (Rare / Nintendo (Midway license), 1994) · Manual · 43 pages · 30 sections · original scan

Page 1

MIDWAY NOVEMBER 1994

16-40047-101

KILLER INSTINCT

OPERATIONS MANUAL

  • includes operation parts information wiring diagrams
Page 2

TABLE OF CONTENT! Section 1 Operation and Troubleshooting

Installation & inspectio Location Requirements. Cabinet Assembly Diagram Servicing...... Game Feature: Starting-u Player Controls. Control Panel Diagram Game Operations..... Control Switche: Control Switch Location Diagra Menu System Operation........ Operation Main Men Diagnostic Tests.. Switch Test. DIP Switch Test & Tabie. CPU Board Test... Sound Board Test. Monitor Patterns Test. CORHDSOHROOOND RRLod NOOnawwn-- Cod Game Audits... Game Adjustments. Standard Pricin Custom Pricing. Utilities...... Volume Adjust. Troubleshooting. SB wD a

Section 2 Parts information Cabinet Hardware, Electronic Rack, Monitor & Manuals Control Panel, Fluorescent Lamp Assembly, Speaker, Transformer Assembly & Cable: CPU/Sound Board. Switcher Power Supply Assembly.

Section 3 Diagrams and Schematics JAMMA Chart........... Interboard Wiring Diagram.. Power Wiring Diagram & Transformer Cabinet Wiring Diagram.. Electronic Rack Assembt

Killer Instinct™

©1994 Nintendo/Rare

Game by Rare

Killer Instinct is a trademark of Nintendo

Manufactured and sold by Midway Manufacturing wonpany under license.

Page 3

KILLER INSTINCT

SECTION one

Operation

Page 4

SAFETY NOTICES The following safety instructions apply to all game operators and service personnel. Specific wamings and cautions will be found throughout this manual where they apply. We recommend that you read this page before preparing your game for play.

/A\. CAUTION

HARD DRIVE. The operator must order special a shipping box and anti-static bag from the distributor in order to send the hard drive in for repair or replacement. Shipping Box #08-7936, Anti-Static Bag #20-9638-3

AC POWER CONNECTION. Before connecting the game to the AC power source, verify the Voltage Selection Chart jumper wires are installed correctly for the line voltage in your area. For details refer to Section 3.

PROPERLY GROUND THE GAME. To avoid electrical shocks, do not plug in the game until it has been inspected and properly grounded. MIDWAY games should only be plugged into a grounded 3wire outlet.

NOTE: The control panel is removable. Ensure that the ground braid is securely attached to the contro} panel after servicing.

OISCONNECT POWER DURING REPAIRS. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game.

USE THE PROPER FUSES. To avoid electrical shock, use the replacement fuses which are specified on the inside back cover. The replacement fuses must match the original fuses in fuse type, voltage rating, and current rating.

MONITOR PRECAUTIONS. When removing or repairing the monitor, extra precautions must be taken to avoid electrical shock because high voltages may exist within the monitor circuitry and cathode ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the monitor with you hands or metal objects! Always discharge the CRT by the following method: Attach one end of a large, well-insulated, 20kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by stiding it under the anode cap. Wait two minutes and discharge the anode again.

HANDLE FLUORESCENT TUBE AND CRT WITH CARE. If you drop a fluorescent tube or CRT and it breaks, it will implode! Shattered glass can fly eight feet or more from the implosion.

ATTENTION !

PROPERLY ATTACH ALL CONNECTORS. Be sure that the connectors on each printed circuit board (PCB) are properly connected. if they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. All connectors are keyed to fit specific pins on each board.

Page 5

SETUP PROCEDURE

INSTALLATION & INSPECTION

Game Location Power Temp Humidity

Requirements Domestic 120V @ 60 Hz 32° F to 100° Not to exceed 95% relative. Foreign 230V @ 50 Hz (0° C to 38° C)

Cabinet Statistics Dimensions Weight

Width 27° Approximately 402Ibs Depth 41" Height 73"

  • Remove all items from the shipping containers and set them aside. Inspect the exterior of the cabinet and the control panel for any damage.
  • The coin door keys are attached to one of the joysticks. Unlock and open the coin and cash box doors. Remove the spare parts stored in the cash box and remove the rear door keys located on a key hook inside the coin door.
  • Remove the screws holding the rear door then unlock and remove the door. Inspect the cabinet interior for any signs of damage. Check all major assemblies to assure that they are mounted securely.

4, Refer to the Cabinet Wiring Diagram (Section 3), and check to see that all cable connectors are correctly secured. Do not force connectors. Watch for damaged connectors and avoid making reversed connections.

  • If a padiock is desired, turn the rear door hasp so that it protrudes from the hole in the back of the cabinet. Remove the two nuts inside the cabinet, at the top and middle of the rear door opening. Then slide the hasp off of the bolts. Turn the hasp, slide it back on the bolts and replace the nuts.
  • Next, locate the four leg levelers among the spare parts in the cash box. There are four threaded holes on the bottom of the cabinet; one in each corner. Place one leg leveler (with its hex nut) in each of the threaded holes. Lower each leg leveler until the cabinet is stable and level.

1! WARNING !! The cabinet is top heavy.

  • Determine the value of your line voltage with a meter. Then, check the jumper wires to the main power supply transformer. Be sure it is jumpered to correspond to your local line voltage value. If necessary, change the jumper wires to the transformer in accordance with the Voltage Selection Chart in Section 3.
  • Lay the line cord (connected to the power chassis) in the slot along the bottom edge of the rear cabinet door. Replace the rear door and screw (lock) it securely. NOTICE: Tamper proof screws are included in the spare parts bag. These screws are optional and may be used to secure the rear door panel. A special wrench (20-9626) for the installation of tamper proof screws is also provided. Close and lock the front coin and cash box doors.
  • Plug the game into a grounded (3-terminal) AC wall outlet. Switch ON the game, using the ON/OFF switch located on the upper left rear of the cabinet.

1-3

Page 6

CABINET ASSEMBLY

FLUORESCENT BULB

MARQUEE — :

SPEAKER

25” MONITOR

CONTROL PANEL

JOYSTICK

BUTTONS

COIN DOOR

CASH BOX DOOR —>

Front View

1-4

Page 7

CABINET ASSEMBLY

ON/OFF SWITCH

VENT COVER —

CPU/SOUND BOARD 1

PROGRAMMED HARD DRIVE Loon E

FAN |

REAR DOOR SWITCHER POWER SUPPLY i POWER, PACK’ ASSEMBLY

i LINE CORD

Rear View

1-5

Page 8

SERVICING

Servicing the Control Panel

Switch off power to the game and open the coin door. The controt Panel ts held in place by two latches (located inside the cabinet) which provide constant pressure on the strikes. To release the latches, reach through the coin door opening toward the right, left and front of the cabinet. Do not reach Straight back through the coin door or you could damage the monitor control board. Lift the latch handle and unhook the wire fasteners. Grip the joysticks and carefully tilt the control panel back on its hinge.

To return the control panel to its normal position, carefully lean it forward until it rests on the cabinet. Be careful notto let the control panel slam down onto the cabinet, or to pinch any wires. Always reclasp the latches.

Removal of the Viewing Glass Switch off power to the game and open the control panel. Remove the five hex-head screws and the black metal strip at the bottom of the viewing glass. Carefully, slide the glass from the side grooves and lift it clear of the cabinet.

Removal of the Monitor Bezel Switch off power to the game. Open the control panel and remove the viewing glass. Lift the bezel off of the monitor.

Monitor Replacement We recommend that you read the SAFETY NOTICES section thoroughly before beginning this procedure. Switch off power to the game. Remove the viewing glass and the monitor bezel. Completely disconnect the monitor from ail of its cabling. Remove the four flange nuts securing the monitor's mounting flanges to its mounting panel. Pult the monitor carefully from the cabinet.

VAN CAUTION

The monitor does not require an isolation transformer. However, when servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM LINE VOLTAGE WITH AN ISOLATION TRANSFORMER. THE MONITOR IS HEAVY. BE SURE IT IS FIRMLY SUPPORTED IF IT MUST BE REMOVED FROM THE CABINET.

Hard Drive Replacement REMEMBER: HARD DRIVES ARE FRAGILE. In order to return the hard drive, you must contact your distributor to obtain a special shipping box and anti-static bag. SHIPPING BOX #08-7936 ANTI-STATIC BAG #20-9638-3

Switch off power to the game and open the rear door. Unplug the ribbon cable from the hard drive. Loosen the four M3-.5 x 4mm Phillips truss head screws holding the bard drive to the mounting bracket. Lift and pull the hard drive toward you to remove it from the bracket. Remove and retain the four screws.

Page 9

Open the shipping box. Remove the top white foam packing and anti-static bag, set them aside. Remove the center two inserts from the gray foam packing. This creates an opening approximately 4° x 2-3/4". Place the hard drive in the anti-static bag and then in the opening in the gray foam packing. Replace the white foam packing so that the bubble side faces up. Seal the box.

To reinstall the hard drive, first screw the four M3-.5 x 4mm Phillips truss head screws about half way into the drive. Arrange the hard drive so that the PC board faces the mounting bracket and the ribbon cable connector points up. Line the screws up with the slots and slide it back and down, into the lock position on the bracket. Tighten the screws. Plug in the ribbon cable from the CPU/Sound board.

NOTE: The ribbon cable connector is keyed. Pin 1 of the ribbon cable has a red line going to it. The connector on the hard drive is fragile. Do not force the ribbon cable connector onto the hard drive connector.

Removal of the Marquee Switch off power to the game. Remove the hex-head screws from the black marquee retaining strip located on top of the header. Remove the strip and carefully lift the marquee and the marquee glass from the top of the header. Store the marquee carefully to prevent damage.

Removal of the Fluorescent Light Assembly Switch off power to the game. Remove the marquee glass and the marquee. The fluorescent bulb is now accessible for replacement. Remove the plastic lamp locks. Grasp the bulb, give it a quarter turn, and remove it from its socket. Carefully, place a new bulb into the socket, and turn to reinstall.

To remove the entire light fixture, disconnect the fluorescent light assembly from its power cable. Remove the screws that hold the assembly to the cabinet then lift out the assembly.

!! WARNING !! If you drop a fluorescent tube and it breaks, it will implode! Use care in handling.

Removal of the Speakers Switch off power to the game. Remove the marquee and the marquee glass. The speakers come out from the front of the cabinet. Be sure to disconnect the cabling and remove the nuts on the mounting screws before attempting to remove the speakers from the enclosure. Carefully, reinstall the seals upon completing any task in the speaker enclosure.

Volume Control, Begin Test Switch, and Service Credit Switch Open the coin door. The game's volume control and diagnostic push-button switches are located on a smail bracket on the door. The volume is controlled by the two center buttons. Press the Volume Up or the Volume Down button until the desired sound level is reached. The Begin Test switch, on the right, activates the game's menu system. The Service Credit switch, on the left, allows credits to be allotted for service testing without affecting the game's bookkeeping total. CONTROL SWITCH LOCATIONS

! seavice VOLUME VOWUME BEGIN ceeors Dow uP Fest [oO OO SO)

Page 10

GAME FEATURES

STARTING UP Switch on power to the game. The game runs through a start-up routine. Insert the desired amount of coins, bills or tokens, Select which player receives the credit by pressing the appropriate Start button.

NOTE When an error is detected during the Start-up tests, game start-up does not progress, and an error message appears on the screen.

PLAYER CONTROLS Start Button Each player has a Start button. The Start buttons allow one or two players to begin or continue play.

Joysticks Each player has a joystick which he uses to control an on-screen character. The player can make the on-screen character move, jump or duck.

High Attack An attack that originates above the waist, such as a punch.

Low Attack An attack that originates below the waist, such as a kick.

Quick A “quick" attack is a short range, short duration attack that inflicts little damage to an opponent.

Medium A“medium" attack is a moderate range, moderate duration attack that inflicts some damage to an opponent.

Fierce A "fierce" attack is a long range, long duration attack that inflicts much damage to an opponent.

NOTE Use joystick and button combinations to discover secret moves.

CONTROL PANEL DIAGRAM

Sart Sat

Jump High Attack Jump High Attack

QuickMediumFierceQuickMediumFierce

Move Move © (e) (e) Move Move ©

Duck©©©)Duck©©©
QuickMediumFierceQuickMediumFierce

Low Attack Low Attack

1-8

Page 11

GAME OPERATION

The KILLER INSTINCT Control switches are located inside the coin door.

CONTROL SWITCHES Control switches are located on a bracket inside the coin door.

The Siam Tilt switch prevents pounding for free games.

The Volume Down and Volume Up push-button switches increase or decrease the volume level of the music and speech. The volume level can be adjusted during the Attract Mode or during menu system operation. For greater profits, set your game's volume level at a nice loud setting.

The Begin Test push-button switch enters the game's menu system. Press the Begin Test switch to access any of the menu system functions.

The Service Credit push-button switch is a special feature switch that allots credit without affecting the game's bookkeeping total.

NOTE The coin door must be open for the control switches to work.

CONTROL SWITCH LOCATIONS

SERVICEVOLUMEVQ.UMEBEGIN
cReDISDOWNwoTEST
QO000

1-9

Page 12

MENU SYSTEM OPERATION

OPERATION All game audits, adjustments and diagnostics are options of the Main Menu. Each option, in turn, has its own menu that lists several choices which you may act upon as desired.

Press the Begin Test switch on the coin door to open the Main Menu (shown below). Game adjustments, bookkeeping and diagnostics are all accessible from this menu.

Use either joystick to move the cursor up and down the menu screen. Notice that the Options are highlighted in sequence. Press any button to open a highlighted option. Only highlighted options can be opened.

To exit the Main Menu, use either joystick to select EXIT TO GAME OVER and press any button.

MAIN MENU

Page 13

DIAGNOSTIC TESTS Use either joystick to select the Diagnostic Menu and any button to open it. Then, use either joystick to move the cursor up and down the menu and any button to open a highlighted option.

DIAGNOSTIC MENU

Switch Test The Switch Test allows the operator to test the switches on the control pane! and in the coin door.

Use either joystick to highlight the Switch Test and any button to begin the test.

During the Switch Test the top of the screen shows the control panel switches while the bottom of the screen shows the coin door switches. Press a control panel or coin door switch and the switch location on the screen lights. Release the switch and the screen returns to normal.

To exit the Switch Test, press both Start buttons together.

SWITCH TEST SCREEN

4-11

Page 14

DIP Switch Test The DiP Switch Test allows the operator to check or change the position‘of the DIP Switches on the CPU Board.

Use either joystick to select the DIP Switch Test and press any button to access the DIP Switch Setting Tables. The screen displays the current DIP Switch settings. To change a setting, slide the switch to the desired position, then check the screen to verify the new setting. in some cases, setting a function to OFF actually enables the function. For example, setting DIP Switch Coinage to Off enables DIP Switch Coinage.

Press any button to return to the Diagnostic Menu.

DIP Switch 1 Setting Table

Sw7 | swe

Attract Sounds. No Attract Sounds

Ending Moves No Ending Moves

Display Violence Warning No Violence Warning

Gart Fri

USA2 Ger2 Fra USA3- Ger3 Fro USA4 = Gera Fra. USAECA GerECA FECA USAS USA1O Froe Play Free Play Frma Play ‘ountry USA Germany France Not Used

One Counter Two Counters

[rest Mode Test Mode On

  • Indicates Factory Setting.
Page 15

CPU Board Test Select the CPU Board Test with either joystick then press any button to start the automatic test. When this test is activated, a "rug" pattern appears on the screen. When the rug pattern ends, Test O.K. or Test Failed appears on the screen. This test returns to the Diagnostic Menu automatically.

Sound Board Test This test allows the operator to listen to some of the sounds this game is capable of producing.

Use either joystick to select the test, then press any button to open the test menu. The screen displays two test options. Use either joystick to select an option and press any button to begin the test.

SOUND TEST MENU

GENERAL TEST analyzes the sound circuitry. The screen shows a list of error codes. A successful test Causes a single "tone" to sound. Detection of a fault causes a series of tones or no tone at all to sound. Press any button to return to the Sound Test Menu.

PLAY SOUNDS test synthesized and digitized sounds from the CPU/Sound Board. Advance to the next sound with any button. Use either joystick to end the test.

Select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU and press any button.

Page 16

Monitor Patterns The Monitor Patterns Test provides a menu for testing the monitor.

Select the test with either joystick. Press any button to open the test menu. Once the Monitor Patterns Test menu is open, use either joystick to select an option, and any button to begin it.

MONITOR PATTERNS MENU

The RED, GREEN and BLUE SCREEN tests fill the screen with either red, green or blue. Press any button to Teturn to the Monitor Patterns Menu.

The COLOR BARS test fills the screen with several shades of colors to help with red, green and blue level adjustments. Each color should appear sharp and clear. Press any button to return to the Monitor Patterns Menu.

The CROSSHATCH PATTERNS test fills the screen with a grid and a series of dots. The grid and the dots should be clear. The dots should be round. Press any button to return to the Monitor Patterns Menu.

Hf any of the Monitor Patterns Test shows a need for adjustment, use the proper knobs on the Monitor Controls Board.

Use either joystick to select RETURN TO MAIN MENU or BACK TO DIAGNOSTIC MENU, then Press any button.

Page 17

Check Disk This test checks the hard disk drive.

Use either joystick to select the test, then press any button to activate it. Press any button to return to the Diagnostic Menu.

CHECK DISK SCREEN

Burn-in Test The Burn-in Test continually repeats the CPU Board Test. Use this test to find intermittent CPU Board probtems.

Use either joystick to select the test, then press any button to activate it. When the Burn-in Test detects an error the test stops and an error message is displayed on the screen. To exit this test, switch the game off, then on again.

The Audit Table specifies the number of Burn-in cycles that have been successfully completed.

Page 18

COIN BOOKKEEPING The Coin Bookkeeping Table records the coin box totais and the game play counters.

Use either joystick to select the Coin Bookkeeping Menu, then press any button to open it.

To exit Coin Bookkeeping, use either joystick to select RETURN TO MAIN MENU and press any button.

COIN BOOKKEEPING MENU

Page 19

GAME AUDITS Use joystick to select the Game Audits Menu, then press any button to open it. Page through the available audits by selecting NEXT AUDIT PAGE or LAST AUDIT PAGE. Select RETURN TO MAIN MENU and press any button to exit Game Audits.

NOTE Game audits cannot be set. They can only be cleared.

AUDIT MENU - PAGE ONE

AUDIT MENU - PAGE TWO

Page 20

Game Audits Continued.

AUDIT MENU - PAGE THREE

AUDIT MENU - PAGE FIVE

1-18

Page 21

Game Audits Continued.

AUDIT MENU - PAGE EIGHT 1-19

Page 22

Game Audits Continued...

AUDIT MENU - PAGE TEN

AUDIT MENU - PAGE ELEVEN

1-20

Page 23

Game Audits Continued...

AUDIT MENU - PAGE THIRTEEN

1-21

Page 24

GAME ADJUSTMENTS The Game Adjustments allow the operator to customize the game.

Use either joystick to select the Game Adjustments Menu. Press any button to open the menu.

The Game Adjustments Menu offers several options. Each option has several choices. Use either joystick to select an option, then press any button to open the option. The next menu screen provides a setting value. Use either joystick to change the setting value and press any button to lock it in.

To exit the Adjustments Menu, use either joystick to select RETURN TO MAIN MENU, then press any button.

NOTE Adjustment values set by DIP SWITCH, override adjustment values set by the menu system.

GAME ADJUSTMENTS MENU

Game Adjustments

Standard Pricing Standard pricing allow the operator to choose any of the "standard" selections from the Standard Pricing Table. See page 1-24.

Modify the setting value with either joystick. Press any button to lock in the new value and return to the Adjustments Menu.

Custom Pricing Custom pricing alfows the operator to install pricing other than that of the Standard Pricing Table. Custom pricing also allows the operator to select the maximum amount of credits per game, the amount of credits required to start a game, and the amount of credits required to continue a game. This option is being adjusted from the DIP Switch settings. See page 1-25.

Modify the setting value with either joystick. Press any button to lock in a new value and return to the Adjustment Menu.

1-22

Page 25

Game Adjustments Continued...

Free Play This option selects free play. The setting choices for this adjustment are: -No ~ Yes ~ Factory Setting: No

Computer Difficulty This option determines how tough the computer opponents are. The setting choices for this adjustment are:

  • (1) Extra Easy
  • (2} Easy
  • (3) Medium
  • (4) Hard
  • (5) Extra Hard
  • Factory Setting: Medium

Winning Streak Reset This option determines the number of games that must be played before the high scores automatically reset to factory settings. The setting choice for this adjustment are:

  • No Reset ~ 5000 Games
  • 10,000 Games
  • 15,000 Games
  • Factory Setting: No Reset

1-23

Page 26

STANDARD PRICING TABLE

NameSetting - CregivCoinCoinCoin 3Coin 2Coin4Bills
UsAt1/25¢@ to Start; 2 to Continue)25¢25¢$1.00
USA225¢{2 to Start 1 to Continue)25¢25¢$1.00
USA 31/25¢(1 to Start; 1 to Continue)2828e$1.00
USA4150¢, 9/$1.00 (1 to Start; 1 to Continue)25025¢$1.00
Usa 5s1/50¢, 4/81.00 (2 to Start; 1 to Continue)25¢25¢$1.00
USA61150e{1 to Start; 1 to Continua)25¢26¢$1.00
USAT1/50¢, 3/$1.00 {1 to Start; + to Continue)25¢28¢$1.00
USAg508, 4781.00 (2 to Start; 2 to Continue}25¢25e$1.00
usagV25¢te Continue)25¢25e$1.00
USA 101/250to Continue)25¢25¢$1.00
USA ECA1/25¢, 4/81.00 {2 to Start; 2 to Continue)$1.0010825¢Se$1.00
‘German 141DM, &/5DMDMSDM
German 21/10, 7/5DM1DM5DM
German 341M, 8/5DM10MSDM
German 4JDM, 6/50M.10M5DM
German 541DM, 6/SDM4DMSDM
German ECA421M, 2/2DM, 6/5DM50M1DM20M
France 1BIS, S10FoF10F
France 22ISE, AOFoF40F
France 3WSF, Y10FoF40F
France 4WSF, 2/10FSF10F
France 52ISF, SOF, 11/2 x 10FSF10F
France 62ISE, A/OF, 9/2 x 10Faf10F
France 7{/5F, SOF, 7/2 x 10FoF10F
France &USF, 2/40F, 5/2 x 10FSF40F
France 913x 1F, 2561¢SF
France 10V2 x 1F, a/SF1FoF
France 111/3 x 1F, 2/5F, 5/2 x SF1FSF
France 12M2 x 1F, SBF, 7/2 x 5F1FFF
France ECA43x 1F, 2/5F, 5/2 x SF1F10FSF
Canada12 x 25¢, 461.0025¢$1.00$1.00
‘Swiss 1AE, /SF1FSF
Swiss 2AA, iSF1FSF
Swiss 3AE, BSF1FSF
Italy17500 lire500 lire800 lire
UK t1/20P, /50P20PSOP
UK22/20P, /50P20P50P
UK ECA1V20P, 3/50P, 7/81.00£1.0020PsoP40P
UK Elec wiCCU4UGOP, 2/50P, 4/81.00£1.0020PSOP10P
Spain 11/100 peseta, &/500 peseta100 peseta500 pesata
‘Spain 21100 pesata, 5/500 peseta100 peseta800 peseta
Australia 1413 x 208, 2/$1.00208$1.00
Australia 2U5 x 202, 1081.00206$1.00
Japan 11100 yen100 yen400 yen
Japan 22100 yen100 yen100 yen
Austria 1WS schiling, 2/10 schilling5 schilling10 schilling
Austria 2U2 x5 schilling, 3/2 x 10 schilling5 schilling10 schilling
Belgium 11v20F20F20F
Beigium 2/20F20F20F
Belgium 32/20F20F20F
Belgium ECA1/20F50FSF20F
‘SwedenV3 x1 krona, 2/5 krona1 krona5ktona
New Zealand 113x 20620820¢
New Zealand 2V2 x 20¢20¢20¢
Netherlands4it HF, 372.5 HF1 HFI2.5 HFL
Finland1 markka{ markka1 markka
Norway12 x1 krone, 3/5 x 1 krone1 kronekrone
Denmark2x 1 krone, 3/5 krone, 7/2 x 5 krone1 krone5 krone
Antillies1/25#, 4/1 guilder2581 guitder
HungaryV2 x 10 forint, 3/2 x 20 forint40 forint20 forint

1-24

Page 27

(1)

@)

(4)

6)

(6)

”) CUSTOM PRICING MENU

Coins inserted accumulate units. This adjustment specifies the number of units given for each coin in the fourth chute (see “units/credit").

This is the number of coin units required to buy one credit.

There is one bonus credit awarded after this many coin units have accumulated.

This is the minimum number of units required before any credits are awarded.

ach player needs this many credits to begin a game.

Each player needs this many credits to continue a game.

This is the limit for the credit counter. Additional coins inserted will be lost (factory setting: 30).

1-25

Page 28

UTILITIES The Utilities Menu allows the operator to clear the game's bookkeeping memory.

Use either joystick to select the Utilities Menu, then press any button.

UTILITIES MENU

Use either joystick to select a utility. Press any button to activate the selection. A dialogue box appears and the Operator can choose to reset the utility. For example:

Use either joystick to choose a setting value. Press any button to lock in the new setting value.

To exit the Utilities Menu, use either joystick to select RETURN TO MAIN MENU, then press any button.

1-26

Page 29

VOLUME ADJUST The Volume Adjust feature allows the operator to determine the sound and music level of the game.

The volume level can be adjusted from either the Attract Mode or the Menu System. Press the Volume Up button to raise the volume level and the Volume Down button to lower the volume level. Either joystick can also be used to raise or low the volume level. The current volume level is shown with a red bar. Press the any button to return to the Main Menu.

VOLUME ADJUST PRESS ANY BUTTON TO EXIT

(MAXIMUM)

(CURRENT VOLUME LEVEL)

{MINIMUM}

1-27

Page 30

TROUBLESHOOTING

PROBLEM No picture or distorted pictura.

Turn game On and nothing happens.

No sound.

No general illumination.

Press start button and nothing happens.

No credit given for number of coins inserted.

Too many credits for number of coins inserted.

Game stay in test mode. POSSIBLE SOLUTION Check for faulty video board or monitor. Check for disconnected video signal cable.

Check line fuse. Check for +5Vde at pins C, D, 3 and 4 of the JAMMA connector.

Check the speaker and the speaker connection to pin L and 10 on the JAMMA connector. Check volume control setting. Check for +12Vde at pins F and 6 on the JAMMA connector.

Check the 1A, S.B. fuse in the A.C. power pack assembly.

Check tor open wires between the button and the CPU board. Check for contamination on CPU board pins or the Start button switch blade contacts. Check for proper ground.

Check DIP switch coin settings. Check for contamination on the coin ‘Switch contacts. Check for an open wire between Coin Switch 1 and pin 16 on the JAMMA connector or Coin Switch 2 and pin T of the JAMMA connector.

Check the game pricing settings. Check for a short between pins T & 16 on the JAMMA connector.

Check that the switch #8 of DIP switch bank #2 is set to off.

1-28

Page 31

KILLER INSTINCT

SECTION two

Parts

Page 32

CABINET HARDWARE

Cabinet Assembly Lock Retainer Plate Upper Door Lock Cam Leg Leveler Piate Lock Plate Door Bracket Shaft Caster 20" Vent Hole Cover Door Cam Lock Caster Wheel

Coin Door Assembly Coin Vault Door Mars Chute Coin Meter w/Diode A-19178-40047 01-7264 01-8989 01-9155 01-11285 01-11291 02-4404 03-7602 20-6542-TB 20-9627

09-50000-33 09-41000 0171-11379 5580-13476-00

Glass Retainer Bracket 01-9607.1 Security Bracket 01-11955 Marquee Retainer 03-8252-2 Glass Edge Retainer 03-8358 25" CRT Bezel 03-8497 Cash Box Tub 03-8863 (Qty = 2) Leg Adjuster, 3 inch 08-7377 (Qty = 4) Clear Marquee Giass 08-7456-4 Clear CRT Glass 08-7456-10 Marquee 31-2020

ELECTRONIC RACK

Electronic Rack A-19591 *Before retuming hard drive to

Switcher Power SupplyA-15202-1distributor order:
CPU/Sound AssemblyA-19650-40047Shipping Box #08-7936
Hard Drive Mounting BracketA-19595.1and
Programmed Hard Drive*A-19596Anti-Static Bag #20-9638-3

Fan Grille 03-9223 Fane Guard 20-9420 Fan 20-9947

MONITOR

Monitor Support Bracket 01-10819 25" Monitor 5675-13399-01

MANUALS

DBV Installation Instructions Instruction Manual 16-9637 16-40047-101

2-2

Page 33

CONTROL PANEL

Housing & Control Panel Assembly A-19584 Control Panel Assembly A-19586 Plate A-19587 Control Panel Cable H-19597 Control Panel Latch Bracket 01-11996 Clear Overlay 03-9304 15 Link Safety Chain 20-9275-2 White Pushbutton 20-9687-2 Blue Pushbutton 20-9687-3 Control Panel Hinge 20-9841.1 8-Way Joystick 20-10178-3 Screened Overlay 31-2021 Housing w/ Hinge A-19585 Toggle Latch 20-9347

FLUORESCENT LAMP ASSEMBLY

Fluorescent Housing & Bracket A-15890 Lamp Locks 03-8327 18° Fluorescent Bulb, 15W 24-8809

SPEAKER

Speaker Grille 01-11859 8Q Full Range Speaker 5555-13961-00

TRANSFORMER ASSEMBLY

Power Pack Assembly Fuse, SB, 1A, 250V Fuse, SB, 3A, 250V A-15916 5731-06569-00 5731-10356-00

CABLES

Dixie-Narco Cable Control Panel Cable Main Harness Cable Speaker Cable Line Voltage Cable 2MM Ribbon Cabie H-17019 H-19597 H-19598.1 H-19599 H-19639 5795-14459-02

2-3

Page 34

CPU/Sound Assembly A-19650-40047

DesignationPart NumberDescription
U98A-5343-40047-1Game EPROM
U10A-5343-40047-2Sound EPROM
UliA-5343-40047-3Sound EPROM
ul2A-5343-40047-4Sound EPROM
U13A-5343-40047-5Sound EPROM
U33A-§343-40047-6Sound EPROM
U34A-5343-40047-7Sound EPROM
U35A-5343-40047-8Sound EPROM
U36A-5343-40047-9Sound EPROM
$1, $25645-09025-00DIP Switch
J35791-12461-10Header, 10-pin
65791-14457-00Header, 44-pin
J75791-12461-15Header, 15-pin
JB5791-12461-08Header, 8-pin

hal

ue uss

un } u34

uo ~ u33

qd

JAMMA

2-4

Page 35

Switcher Power Supply Assembly

A-15202-1

Part Number Description

01-10500 Mounting Bracket 01-12162 Shield 20-9920 P/S Switcher Supply

fe) a 2 ¢ 2) > > fe) c c > SS c > > > c ¢ 5 > i og me ¢ > bog = > ¢ 3c ¢ D ¢ > 1 & Cc C > 5 = SS c » = Se S » ES c fs 5 ¢ 5 fa < > ¢ > | ¢ = DC > =} > ¢ » ¢ 5 I ¢ C

: ° fo}

a

RED (+5V) i i VIGQLET/VIOLET—YELLOW BLACK BLACK } GREEN-YELLOW YELLOW (-5¥) ORANGE (+12)

7 < gS =“ ¢ e > & > ce a é a ~ 4+ go g 4 2 & & ~ 1 2

EE lone)

2-5

Page 36

KILLER INSTINCT

SECTION three !

Wiring Diagrams

Page 37

JAMMA Chart

FUNCTIONWIRE COLORWIRE COLOR | FUNCTION
GroundBlackABlackGround
GroundBlackBBlackGround

+5VDC Red Cc Red

+5VDCRedDRed
-5VDCYellowEYellow

+12VDC Orange F Orange

KeyHKey
Coin Counter 2 | Brown-RedJBrownCoin Counter 1
N/CKN/C

Speaker- Brown-Gray L Red-Gray Speaker+

NIGMNC
Video GreenGreenNRedVideo Red
Video SyncWhitePpBrownVideo Blue
Service Credits | White-GrayRShieldVideo Ground
Slam TiitBlack-Green$Black-BlueTest
Coin 2Black-RedTBlack-Brown

2 Start Violet-White U White 2 Down Violet-Brown WwW White-Brown 1 Down

2 UpViolet-BlackVvWhite-Black1 Up
2 LeftViolet-Red_xWhite-Red1 Left
2 RightViolet-OrangeYWhite-Orange_]1 Right
2 Quick/HighViolet-YellowZWhite-Yellow1 Quick/High
2 MediViolet-GreenaWhite-Green1 Medium/High
ieViolet-BiuebWhite-Blue1 Fierce/High

Violet c White-Violet Not Used

N/CdNIC
N/CeN/C
GroundBlackfBlackGround

SOLDER SIDE COMPONENT SIDE

3-2

Page 38

3-3

GROUND

NZC es Ci A BLACK ORANGE GROUND 7, BLAGK B CPU/SO A-19650- GU \D BOARD 40047

Interboard Wiring

Page 39

Power Wiring

NOTE:
For 230VAC Operation1 feTo
1. Fuse is 2A 5.8.cK YE!2 |[2Fit
  • Voristor 's 250V. ye picter OE f 3 (/3 noe tomp 4 4
A SB. BLKavH
p olsiVIO_AT1 1vIO_A é.To
ft}AQ=yeL A | 2 |) 2 [yig-vELA:I SEL Switcher
'wiO 631) 3 MOB2 || 2 fiotver~ Power
YF |3 3=
WO-YEL B | 44 [wio-vet 6 |Supply

of YEL ON/OFF

PevA SWITCH|;}i (aE Video
* PLUGWHT=REDL 32 Mo=vEL Monitor

YEL| | YEL-WHT 2] [2 To

SEErlsMain

TRANSFORMER 1A Harness CHART 250¥ 5.8

Transformer Chart

From Power Sw'icres

YEL-RE>LisWHT
ifte | 5WHTaais):*20V Isoctes For
Hi:VIO1Monitor Asc Power
i:$s00
iBRN 103.5,pane
i7 79 )>4-Ne 294 vio-vE_ 4
:BK 115i
1fe | 12|1
:15 | S [sep t32)dvio-ver 2
H| 5BLU-WHT
8BLU-BRN 103.5 3YEL-WHT 2SBY For Bolt 6h:

i * Coin Door

Ss.aaaBLU-BLK 115) bagcj tights. °|
;Voltage |znsuu-reo 132 )\{C®ve

Selection |

Toble }Hy_!
_ H= 7+ a_.
“0S481TRANSFORMER 5610-*3326-00

113) \ 1 BK

|aNOTE:
|jShown As sumpered For 115V Operation.

WHT-RED x | WHT-RED

BLK—YEL;BLK-YELFrom Line Filter

{

VOLTACE SELECTION TABLE Voltage dumper Pins 103.5 [5-6, 7-8, 10-9 TTS 5-6, 7-TT, 10-12 132 5-6, 7-14, TO=15 207__[3-9.10-8 2185 [5-9 10-11 230 5-12, 10-11 47 S=12, 10-18

3-4

Page 40

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 41

Electronic Rack Assembly

Ero vomit aS a : a

‘ee, erm Sukie Roma atbe Og

AMMA CONNECTOR

NN > a Ke A wwr°e%y ernest ome Bion

Cin snes ® sian nae aS Shilo

LOCATE HARD OISC DRIVE MOUNTING BRACKET To BE PARALLEL WITH CORRESPONDING PU RIBBON CABLE HEADER j Bano onve uous

eae or

RACK (WOOD ONLY) 11-9938

Page 42

CONTROL PANEL WIRE COLORS

Player One

Start White

Up White-Black Down White-Brown

Left White-Red Right White-Orange

Quick/High White-Yellow Medium/High White-Green Fierce/High White-Biue Quick/Low — Blue-Black Medium/Low Blue-Brown Fierce/Low Blue-Red Ground Black

Player Two

Start Violet-White

Up Violet-Black Down Violet-Brown

Left Violet-Red

Right Violet-Orange Quick/High Violet-Yellow Mediun/High Violet-Green Fierce/High Violet-Blue Quick/Low Blue-Yellow Medium/Low Blue-Green Fierce/Low Blue Ground Black

FUSES

Line Fuse- (Domestic) 3A. S.B., 125V (Foreign) 2A. §.B., 250V

General Illumination - (Domestic & Foreign) 1A. S.B., 250V

Page 43

WARNING & NOTICES

WARNING USE-OF NON-MIDWAY PARTS OR CIRCUIT MODIFICATIONS MAY CAUSE SERIOUS INJURY OR EQUIP- MENT DAMAGE! USE ONLY MIDWAY AUTHORIZED PARTS.
  • For safety and reliability, substitute parts and modifications are not recommended.
  • Substitute parts or modifications may void FCC type acceptance.
  • This game is protected by federal.copyright, trademark and patent laws. Unauthorized modifications may be illegal under federal law. This also applies to MIDWAY Jogos, designs, publications and assemblies. Moreover, facsimiles of MIDWAY equipment (or any feature thereof) may be illegal under federal law, regardless of whether or not such facsimiles are manufactured with MIDWAY components.
WARNING
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These iimits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generated, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction Manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARNING Prevent shock hazard and assure proper game operation. Only plug this game into a properly grounded outlet. Do nct use a cheater plug to defeat the power cord's grounding pin. Do not cut off the ground pin.

NOTICE When MIDWAY ships a game, it is in compliance with FCC regulations. Your sticker is proof. If the sticker is missing or damaged, legal repercussions to the owner or distributor of the game may result. If your game does contain an FCC sticker, call MIDWAY immediately.

NOTICE No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phanographic recording, nor may be transmitted, or otherwise copied for public or private use, without permission from the publisher.

FOR SERVICE: CALL YOUR AUTHORIZED MIDWAY DISTRIBUTOR.

Killer Instinct™

© 1994 Nintendo/Rare

Game by Rare

Killer Instinct is a trademark of Nintendo

Manufactured and sold by Midway Manufacturing Company under license

MIDWAY MANUFACTURING COMPANY 3401 N. CALIFORNIA AVE. CHICAGO, IL 60618