CATHODE RAY TOMES

Punisher

The Punisher (World 930422) (Capcom, 1993) · Manual · 12 pages · 12 sections · original scan

Page 1

(©1993 MARVEL ENTERTAINMENT GROUP, INC. ALL RIGHTS RESERVED. (© CAPCOM 1993. ALL RIGHTS RESERVED. THIS VIDEO GAME IS PRODUCED UNDER LICENSE FROM THE MARVEL ENTERTAINMENT GROUP, INC.

MANUAL

WARNING This game is for use in the United States. of America and Canada. Sales, export or operation outside of these countries may be construed as copyright and trademark infringement and is strictly prohibited. Violators are subject to severe penalties and will be prosecuted to the full extent of the law.
Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

CAUTION

Please keep the following instructions to keep the PC board in good condition

keep the PC board in good condition.

  • Do not block up the ventilation slots.
  • Do not give the board too much shock.
  • Do not let any liquid go inside the case.
  • Do not disassemble the case. ¢ Do not turn the volume dial excessively.

Disassembling the case or removing the sticker will terminate repair warranty.

Page 4

WARNING

THIS GAME MUST BE GROUNDED, FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

WARNING: This equipment generates, uses and can radiate radio frequency energy and if not used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J and PART 15 of FCC RULES, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.

“WINNERS DON’T USE DRUGS” William S. Sessions, Director, FBI

*IN COOPERATION WITH THE AAMA AND FBI ANTI-DRUG CAMPAIGN*

CAPCOM, USA INC.

INVITES YOU TO USE

OUR SERVICE NUMBER FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER CAPCOM GAME YOU NOW HAVE ON LOCATION. PLEASE HAVE GAME SERIAL NUMBERS AND CABINET NUMBERS READY.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Direct Number 08) 727-0400

Page 5

@ SETTING INSTRUCTIONS

O PCB CONNECTOR

JAMMA STANDARD O CRT MONITOR HORIZONTAL

O CONTROL PANEL 2 PLAYERS SIMULTANEOUS

NC.

(COIN LOCK OUT 2) SP(-) o& Ne yaa VIDEO GREEN BWAVLEVER BUTTON (Shot) eee (Shot 1) SERVICE SW Nc O 8-WAY LEVER: used to move the player in 8 ways. COIN Sw2 COINSW1 O ATTACK BUTTON: used to attack. START SW2 ‘START SW 1 © JUMP BUTTON: used to jump. aur {PUP 2P DOWN 1P DOWN Push both buttons simultaneously to execute powerful MEGACRUSH. 2P LEFT 1P LEFT 2P RIGHT 1P RIGHT 2P SHOT 1 1PSHOT1 SP SHOT2 1PSHOT2

No. Ne. @ CONNECTORS Ne. Ne.

No. Ne.

GND

GND

« PARTS NAME CRITE-GEDA-2 986: (HIROSE) AUDIO OUT cN2 CN4 1168. 056-o4b : (KEL)

CN2 — JAMMA CONNECTOR CN4 — VO CONNECTOR for PLAYER 3 N/A CNS — VO CONNECTOR for PLAYER 4 N/A NE — OPTIONAL OUTPUT CONNECTOR AUDIO OUT — used only for CAPCOM Q SOUND cabinet CN1 —NA CNS —NA

Page 6

ABOUT EEP-ROM

This board “The Punisher’ is equipped with EEP-ROM and you can change the various settings on screen.

ABOUT TEST MENU

TO OPEN THE MENU

  • Turn on the main switch. Then push the test switch” inside the cabinet and following menu will appear. («screen a)

“If your cabinet is not equipped with a test switch, connect a ground terminal and a test switch terminal of JAMMA connector.

EST MENU

INPUT OUTPUT TO SELECT AN ITEM

SOUND TEST

COLOR BAR * Select an item with 1P lever and SYSTEM CONFIGURATION decide with 1P ATTACK button. DOT CROSS HATCH

Seo 1 * To retum to the main menu,

Penoer push 1P START and 2P START SCROLL 2 ; buttons simultaneously. SCROLL 3 s simultaneously.

MEMORY CHECK EXIT

TO CLOSE THE MENU

  • On the menu screen, select EXIT and push 1P ATTACK button.
1.INPUT OUTPUTUsed to test all the input/output switches.

Used to change the sound volume, etc.

  • COLOR BAR Used to adjust the color with color bars.
4,SYSTEM CONFIGURATIONUsed to change various game play settings.
5.DOT CROSS HATCHUsed to adjust the screen size, the focus and the distortion.
6-9.CHARACTER TESTUsed to check all the characters.
10.MEMORY CHECKUsed to test the memory. Main menu appears automatically after the test.

1. 2. 3. 4. 5. 6. 7. 8. 9. 0. 1.

(*screen a)

Page 7

ABOUT SYSTEM CONFIGURATION

+ On the TEST MENU screen, select SYSTEM CONFIGURATION and push 1P ATTACK button. Following menu appears. («screen b)

SYSTEM CONFIGURATION MENU

. COIN 1 COIN 1 CREDIT . CONTINUE ON . MONITOR FLIP OFF DEMO SOUND OFF SOUND Q SOUND . GAME DIFFICULTY 3 (NORMAL) . NUMBER OF PLAYERS 2 . EXTEND 1800000pts . PLAYER SELECT . FACTORY SETTING . EXIT

(«screen b)

TO CHANGE THE SETTING

  • Select an item with 1P lever (UP or DOWN) and change the setting with 1P lever (LEFT or RIGHT). (You can also change the setting with 1P ATTACK button.)

TO CLOSE THE MENU

When all the settings are done, select EXIT and push 1P START button to retum to the TEST MENU. Your settings are memorized in EEP-ROM.

ITEM DESCRIPTIONS

SOUND or MONAURAL. Q SOUND is available only with CAPCOM Q SOUND cabinet. For other cabinets, set to MONAURAL.

6.GAME DIFFICULTYAs the number increases, the game play gets harder.
7.NUMBER OF PLAYERSNumber of initial lives.
8.EXTENDScore points required for 1 up.
9.PLAYER SELECTUsed to select an initial player (PLAYER 1 or PLAYER 2) when the game starts.
10.FACTORY SETTINGTo return to the factory setting, select this item and push 1P START button.
Page 8

SYSTEM CONFIGURATION MENU

1 COIN 1COIN 1COIN 1COIN 1 1CREDIT | 2CREDITS | 3CREDITS | 4CREDITS | 6CREDITS

2COINS | 3COINS 1CREDIT | 1CREDIT

  • Bold face indicates the factory setting.
  • After you change the setting, make sure to select EXIT and push 1P START before tuming off the switch. Otherwise your setting will not be memorized.

CP SYSTEM (ASH)

SERIAL NUMBER STICKER

GAME TITLE STICKER

SEALING STICKER VOLUME DIAL

(‘arate this sticker

will void all warranty

Page 9

HOW TO MOUNT THE P.C. BOARD

  • Installing the P.C.B. foot

4 pcs. of P.C.B. feet are included in the package.

  • Mounting the P.C.B.

These screws are not included in the package. v

Page 10

HELPFUL HINTS IN CASE OF DIFFICULTY

No Raster/No Video

Raster/No Video PROBLEM/CAUSE-CURE

-Check A.C. line cord -Check line fuse -Check monitor brightness -Check power switch and/or interlock switch -Check all solder connections on line filter and transformer -Check for proper orientation of the PCB connector

-Check all PCB to monitor connections -Check power supply voltage on PCB

No Video/Game sounds can be heard

Wrong Colors

Wavy Picture

Horizontal/Vertical Roll

No Sound

Bad Sound

No Switch Input -Check monitor brightness -Check all PCB to monitor connections

-Monitor needs degaussing -Check for proper wiring between PCB and monitor -Check monitor adjustment and adjust if necessary

-Check monitor ground is properly connected to monitor -Be certain sync inputs are properly connected to monitor -Check horizontal hold adjustment

-Check horizontal and/or vertical hold adjustments -Check for proper wiring of sync from PCB to monitor

-Check for -5 volts on edge connector of PCB -Check volume control potentiometer adjustment -Check for + 12 volts on edge connector of PCB -Check wiring from PCB to speaker -Check speaker for low resistance between the “+” and“-” tabs

-Check wiring to speaker for bad solder connections -Check sound with another speaker

-Check ground connection to switch/es -Check wiring between PCB and switch/es for proper connection -Check switch/es with an ohmmeter to verify proper operation Switch Operates Incorrect Function

No Coin Meter -Check wiring between PCB and switches for proper orientation -Check wiring for shorts between switch inputs

-Check wiring to coin meter -Check that +5 volts is on “ +” side of meter -Verify a +5 volt meter is used When coin switch is made and meter pulses, the screen blanks out and/or game resets -Verify that a meter with a diode Is used -If no diode is built in meter, a IN4004 can be used across the meter. Cathode to “ +” side of meter and anode to “-” side of meter

Page 11

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 12

CAPCOM®

USA

3303 Scott Bivd. anta Clara, CA 95054 TEL (408) e740 FAX (408) 496-5720