CATHODE RAY TOMES

Asteroids DP-143-3rd-02B

Asteroids (rev 4) (Atari, 1979) · Drawing Package · 1 pages · original scan

Page 1
Scan of page 1

INPUTS

PLAYER INPUT CIRCUITRY

VIDEO INVERTER

‘The video inverter circuitry is only used in a cocktail ‘game. In an upright game, pin 19 is unconnected and therefore floats. When pin 19 floats, transistor Q16 Is

tuned off and transistor 217 is turned on. Therefore, INV

is ~82 VOC and NONINV is about +8.2 VDC. The result Is anoninverted Xaxis and Y-axis output.

Ina cocktail game, the wiring hamess shorts connec: tor J20's output pin 7 input pin 19. When the video of player 1 is being displayed, pins 7 and 19 are 4-6 VDC. ‘This results in a non-inverted video output. When the video for player 2 is being displayed, pins 7 and 19 are ‘grounded. This causes transistor Q16 to be tumed on and. Q17 to be tumed off. Therefore, INV is +8.2 VDC and NONINV Is 82 VDC. The result is an inverted Xaxis

‘grounded. This causes transistor Q16 to be tumed on and and Y-axis output, causing the monitor's display to be up

‘ide down,

Sheet 2, Side B DP-143402 Grd printing oo se grote Popo sy i ae ae aris aie aise Polgine we

read are selected by ABO

iid inert ice see 2 aoa aa ott ae 8 micntier

game's self-test pro: ‘cedure. SLAM is a signal ead by the MPU to in dicate the status of the ~antislam switch mounted ‘on. the coin door. The MPU reads HALT to determine the state of the vootor generator.

The coin door and some control panel ‘switches are_read by the MPU when SINPI (switch Input one enable) is low. Switches to be read are selected by ABO thru ABZ ‘rom the MPU. All Inputs are read on data line DB7. Switch inputs are “on when pulled to ground.

The game option switches ara read By the MPU when OPTS (option switch enable) is low. Switch toggles to be read are selected by ABO and Bi from the MPU. ‘Switch toggles 1, 3,5, and 7 are read on ‘ata’ line DBO and toggles 2, 4, 6 and 8 are read on DB Toggle inputs are “on” when pulled to ground. OUTPUTS

‘The THUMP sound is heard throughout play. ‘The 555 is connected as an oscillator, abled by N7 pin 2. The frequency is determined by the current coming out of G2. This depends on Its base voltage, which is derived from the fourbit code in N7.

‘The SAUCER sound is heard when an enemy ‘saucer appears. The 568 Is avoltage-controlled oscillator. Its modulating voltage Is derived from the’ $55. The §55 Is a low frequency gscilator. The effect is a warbling sound. ‘changes some component values, in order to provide for 2 different sauce sounds.

_ a

M10 latches control signals 10 tenable different sounds. “The Fire sounds for the Saucer and t ‘Space Ships are generated by two identical circuits. Each contain a 555 operating as a. voltage-controlled ‘oscillator. The Saucer Firesound is In- IMlated by SAUCRFIREEN, and the Space Ship Fire sound is’ initiated by SHPFIREEN. Each of the 5858 Is con. figured in such a way that when they are tenabled, they output a signal ofa specific frequency and amplitude, This signal begins to decay immediately, both in frequency and amplitude, due to the discharge of the contro! capacitors (638 & — 39 for Saucer Fire Sound; C47 & 48 for Ship Fire Sound).

Reser

ieee

‘ LIFE sound Is heard when an extra life is ‘gained. Itis merely 3 KHz from the clock cir.

ow], vorwe],

‘The EXPLODE sound is. heard when any object explodes. Noise is ‘sampled at a frequency determined by P8, and contol bits EXPITCHO and EXPITCH1. Changing the samp ing rate changes the pitch ofthe explosion. The noise is. amplitude- Modulated in R7 by EXPAUDO- EXPAUDS. ea me — Hd

RO and P9 generate random noise. This noise is filtered by P11 and produces the rumble sound heard when the ship Is thrusting, AUDIO OUTPUT

LAMP, LED, AND COIN COUNTER OUTPUT ‘All sounds are mixed In ¥é of PY. This is ‘Audio 1. The signal is then inverted by another 1% of Pi and becomes Audio 2. These out-of. ‘phase signals provide a pustrpull output to the Audio section of the RegulatoriAudio PCB.

This circuit consists of coin counter drivers Q11, 12, Q13 and data latch N11, clocked by the » microcomputer's address decoder. When the Input 10 a diver is clocked high, its collector goes low, Grounding the return of the coin counter in the coin ‘door. When START! or START? is clocked low, it Grounds the START LEDs in the control panel. oan ‘eli HGH —faenvan com a ce tons Toye

< notes a test point PART OF REGULATORIAUDIO PCB

‘Audio inputs AUDIO 1 and AUDIO 2 receive out of phase signals for pustrpull operation. AUDIO DISABLE Is. permarently. grounded for continuous. audio amplitication.

Note: ‘AUDIO AMPLIFIER is PART OF REGULATORAUDIO PCB AND IS REPEATED ON SHEET 1, SIDE-A.

‘The video output clrcult consists of three individual circuits; X axis, ¥ axis, and Z axis ‘video output circus. The X axis and Y axis video output circuits each consist of adigitaltoanalog converter (DAG), currenttovoltage converter, two sample and holds, and amplifier. The Z axis video output circuit consists ofa shift register and a summer. X and ¥ Outputs ‘The DACs (011 and B11) each receive binary numbers from the vector generator’s pos: tion counters outputs. These numbers represent the location of the beam on the monitor. For the non-inverted X axis, the numbers range from 0 to 1023, where 0 is atthe far lett of ‘the monitor screen, 512 is atthe center, and 1023 is atthe far rignt. For the non-inverted Y axis, the numbers range from 128 to 996, where 128 is at the bottom of the monitor ‘screen, 512's at the center, and 996s atthe top. When the X axis and Y axis are inverted, ‘the monitor picture is turned upside down. This is used for a two-player cocktail game.

‘The DACs convert these binary number inputs to current outputs. The DACs! current ‘outputs are applied to the pin 6 inputs of currentto-voltage converters C12 and AtZ. ‘From the currenttovoltage converters, the signal is fed to two sampleandhold Gir ‘cuts: One is non-inverted and the other is inverted. The non-inverted sample and hold ‘consists of one stage of analog switch 012 and capacitor O98 for the X axis, and B12 and, ‘C108 for the ¥ axis. The inverting sample and hold consists of inverter E12, one stage of ‘analog switch D12, and capacitor C119 for the X axis and BIGI2, B12 and C118 for the ¥ axis.

The sample and hold circuits are controlled by SHCON (sample and hold contro). ‘SHOON is derived by gating 3 MHz from the microcomputer clock circuitry and VGCK* from the vector generator's state generator. The result of these inputs insures that the nofrinverted and inverted analog signals that are applied tothe analog switches have sutficiently stabilized before being applied to the sample and hold capacitors.

‘The output swing of SHOON is 8 to +8 VDC. When SHCON is high, the voltage ‘charges of discharges the sampleandé-hold capacitors to the X and Y analog voltage value. The voltages are then applied to the inputs of the second analog switch. These ‘Switches select elther the non inverted or inverted X-axis and Y-axis outputs. The outputs are then amplified by the second stages of C12 and A12 for an impedance-matched out: ‘But to the X'and Y inputs to the monitor. Since the monitor doesn't have field-adjustable Xand ¥ gains, the gains are adjustable by variable resistors 1120 and R126. Z Output ‘The Z axis video output receives six inputs. BVLD (beam valid, from the output of the vector generator’ position counters, tells the Z axis to draw the line, BLANK (vector line ‘lank, from the vector generator’ state machine, tells the Z axis to stop drawing a line. ‘SCALEO thru SCALES (grey level shading scale), from the output ofthe vector generator's data lt, tls the 2 ais the grey lve shading ofthe line tat is bing drawn on the ‘monitor. ‘When BVLD and BLANK are both high, a high is clocked through shift register K9 that tums transistor Q3 off. This allows the scale inputs to be passed through transistor Q2. When BLANK goes low, a low is clocked through K®, transistor Q3 tums on, and the signal is grounded at the base of transistor Q2. “The scale inputs atthe base of transistor Q1 determine Q1's emitter voltage, during the line draw period. The SCALED thru SCALES resistors R36 thru R39, resistor R35, and, resistor Ré0 result in arange of about + 1.0 VOC when all are low and + 4.0 VOC when all {are high. The emitter of Qt follows at about + 1.7 to 4.7 VDC, while the emitter of transistor Q2 follows at about + 1.0 to 40 VDC. This output is applied to the Z input of the ‘monitor. Sine there are brightness and contrast controls in the monitor, there are no ad Justments in tis circuit.

Sheet 2, Side B ASTEROIDS Switch Inputs, Coin Counter, LED and Audio Outputs Section of 034986-XX =F

a

© 1079 Ata ne.