Crash n Score TM-048
Crash 'N Score (Atari, 1975) · Technical Manual · 66 pages · 138 sections · original scan
™M-048
ATARI In en
OPERATION MAINTENANCE SERVICE MANUAL
ATARI INC. 14600 WINCHESTER BLVD, LOS GATOS, CA 9503@ @ (408) 374-2440 @ TELEX 357-488 Copyright © 1975 by Atari, Inc.
Table of Contents
ae INTRODUCTION 1.1 Physical Description of Game 1.2. Brief Description of Play
SPECIFICATIONS 2.1 General 2.2. Electrical 2.3. Environmental 2.4 Owner/Operator Options for Structuring of Play 2.5 Accessories Available on Separate Order
THEORY OF OPERATION 3.1, Functional Description of Game 3.2. General Information 3.2.1. Energizing the Game 3.2.2. TV Monitor 3.2.3. Picture on TV Screen 3.3 Game Sequence 3.3.1 Operating Modes 3.3.2. Attract Mode 3.3.3 Game Sequence in Play Mode 3.3.4 Owner/Operator Options 3.4 Detailed Technical Description of Operation 3.4.1 General Comments 3.4.2 3.4.3 3.4.4 3.4.5, 3.4.6
3.4.8 Playfield Generation Coin Validation Coin Counter Circuit “Q” Latch “Start”
Drivers for “Start” 3.4.9 Game Timer 3.4.10 Score Registers and Score Display 3.4.11 Bonus Credit Circuitry Push Button Switches Credit Accumulator and Lamp Push Buttons so
TV Synchronization Information ” sB tse
n
3.4.12 White/Black Flag Generator, Hit Detectors and Scoring Signal Circuit 3.4.13 Gas Pedal Signals and Processing, of Acceleration Signals 3.4.14 Car Steering Signals and steering Processors 3.4.15 Motion Code PROM 3.4.16 Horizontal and Vertical Motion Counters 3.4.17 Car Reset Circuit 3.4.18 Car Video Processors 3.4.19 Video Summing Circuit 3.4.20 Engine Sound Synthesizers 3.4.21 Crash and Skid Detectors 3.4.22 Screech and Crunch Sound Synthesizers 3.4.23 Sound Summing Circuits 3.4.24 Speaker Driver Stages Ww.
vi
VIL INSTALLATION INSTRUCTIONS,
4.2
4.3 Unpacking Instructions 4.1.1 Examination for Shipping Damage 4.1.2 Mechanical Inspection Energizing the Game 4.2.1. Application of AC Power 4.2.2 Check on Operation of Interlock Switch Game Structuring 4.3.1 Coin Credit Option 43.2. Length of Game Time Option 4.3.3 Bonus Credit Option 4.3.4 Adjustment of Speaker Volumes and Pitches Functional Check of Game Operations 23 4.4.1 Attract Mode 4.4.2. Obtaining Credits 4.4.3 First Play Sequence 4.4.4 Game Time Elapsed, With Credit Remaining 4.4.5 Second Play Sequence
MAINTENANCE AND ADJUSTMENTS, 5.1
5.2 Routine Maintenance 5.1.1 Cleaning 5.1.2 Lubrication Adjustments on TV Monitor
TROUBLESHOOTING AND REPAIR 6.1
6.2 General Procedure 6.1.1. Identifying the Trouble Area 6.1.2 Locating the Trouble Cause 6.1.3 Correcting the Trouble Cause 6.1.4 Verifying Correct Game Operation Test Equipment 6.2.1 Basic Test Equipment 6.2.2. Optional Test Equipment Specific Troubleshooting Information 6.3.1 Antenna Static Modification 6.3.2. TV Monitor 6.3.3 Coin Mechanism
SCHEMATICS, DRAWINGS, AND PARTS LISTS
|. Introduction
1.1 PHYSICAL DESCRIPTION OF GAME
Atari’s “Crash ’N Score” is a video action game in which either one or two players drive race cars on a rectangular playfield and earn score points by driving
through lighted score flags. During play a player has to own upright cabinet that rests directly on the floor. A
maneuver his car around certain obstacles and has to avoid the opponent car. The game is packaged in its
23-inch black-and-white TV monitor is mounted at the top front of the cabinet and players stand in front, facing the screen. The following player-operated controls are provided: on the left side of the cabinet a steering wheel just below the TV screen and a gas pedal near the floor; on the right side another steering wheel and gas pedal; in the center and just below the TV screen two “start” push buttons, with a third “barrier” push button between them. Sheet 1 of drawing number 004172 shows an external view of the cabinet. A coin assembly with two identical coin mechanisms is located at the middle-center of the cabinet. The mechanisms accept quarters only, and coins deposited in either one will initiate game play sequences. The Crash ’N Score game features an owner/operator option that permits on-site game structuring for either 1 credit/coin or 2 credits/coin, (with one credit needed for a 1-player game, and two credits for a 2-player game). The game has an internal credit accumulator that can keep track of up to 15 credits. The cash box is located behind the hinged access door to the coin assembly. Two speakers mounted inside the cabinet, one on each side of the coin assembly, add to the game excitement by producing various types of sounds throughout the play sequence.
1.2 BRIEF DESCRIPTION OF PLAY
In Crash ’N Score a player’s objective is to build
up his point score. He does this by driving his race car
through as many lighted flags as he can before the game time runs out. A player controls car direction with the steering wheel and car speed with the gas
pedal. Ina 1-player game only one race car appears on
the TV screen. On the TV screen the following playfield obstacles appear: oil slicks, unlighted flags, a player-
selectable set of barriers, and (in a 2-player game only) Each flag is labeled with anumeral ranging from 1
collisions with the opponent car.
to7, and at any one moment no more than a single flag through a lighted flag, a number of points equal to
can be lighted. When a player succeeds in driving
that flag’s numeral is added to the player’s accumulated score. The scores are continuously displayed near the top of the TV screen. After a car has driven
through a lighted flag, that flag will cease to be lighted
and some other flag, randomly chosen, will light up. During the final one-eighth of game time the number of points added to a player’s score will be double the numeral shown in the lighted flag. Throughout play engine sounds are heard separately for each car. Other sounds produced at various times during a play sequence can include a tire screech, a crunch as a car skids or runs into an obstacle, buzzing whenever points are scored, and a beeping sound if a bonus credit is awarded. Play ends when the game timer elapses; car motion continues but player controls are disabled and no sounds are produced. However, the final scores from a previous play sequence continue to be displayed until a player initiates a new play sequence. Paragraph 2.4 in Section II of this manual lists the game’s owner/operator options for game structuring, and subparagraph 3.3.4 in Section Ill describes how their structuring can affect the play sequence.
Il. Specifications
2.1 GENERAL Cabinet Dimensions: Height 61 inches, Width 31% in. Depth 30% inches. Cabinet Weight: 289 Ibs. TV Monior: Motorola XM701, black and white, with 23-inch screen. Coin Mechanisms: Two identical mechanisms that accept quarters only; coins inay be deposited in either mechanism to initiate play. Cash Box: Removable, located behind locked access door to coin assembly. Power Cord: Approximately 6 ft. long, extending from rear of cabinet and having grounded three-prong plug for conventional wall outlet.
2.2, ELECTRICAL Power Requirement: Uses conventional wall outlet providing 60-cycle AC (60-Hz, single-phase) at 110 volts; power consumption rated at 94 watts. Fusing: All fuses located inside cabinet; TV monitor has two 1-amp fuses and remainder of game is protected by a 1.25-amp fuse. Power Interrupt Switch: This is a safety switch located inside the game cabinet. It interrupts AC power to the game whenever the rear panel service access door is unlocked and opened. 2.3 ENVIRONMENTAL Operating and Storage Temperature Range: from 32°F to 120°F (ambient temperature).
Relative Humidity: from 0% to 80% without condensation.
2.4 OWNER/OPERATOR OPTIONS FOR STRUCTURING OF PLAY © Coin Credit adjustable for either 1 credit/coin or 2 credits/coin. © Length of Game Time adjustable (from approximately 20 secs. to 2 mins. 50 secs.) @ Bonus Credit either not allowed, or given for
achievement of aspecified score
level (selectable in 10-point increments, from 10 up toa maximum of 90).
2.5 ACCESSORIES AVAILABLE ON SEPARATE ORDER
Video Probe: order from ATARI
Universal Test Fixture: order from ATARI, catalog no. TF101
Ill. Theory of Operation
3.1 FUNCTIONAL DESCRIPTION OF GAME
The block diagram in Figure 3-1 shows the major functional parts of the Crash ’N Score game and how they are interconnected. The TV monitor is a selfcontained unit housed in its own chassis inside the game cabinet. In the game control circuitry the synchronization, blanking and picture information are combined and then sent on a single composite video signal to the monitor. The game's sounds, however, are produced by two speakers that are separate from and not connected to the monitor. The steering wheel and gas pedal on the left side of the cabinet provide player controls for Car | (which appears as white video level on the TV screen); the
steering wheel and gas pedal on the right are for Carl
(medium white video level).
3.2, GENERAL INFORMATION
The general information about the Crash 'N Score game given here provides a background for understanding the Installation Instructions in Section lV of this manual, and the description of game operation in paragraphs 3.3 and 3.4.
3.2.1 ENERGIZING THE GAME: The Crash ’N Score game does not have an external “power on” switch Instead the game is energized as soon as the power cord is plugged into an active AC wall outlet. This outlet_must provide the AC power listed in the Specifications (Section II of this manual).
3.2.2. TV MONITOR: The game’s TV monitor isa selfcontained transistorized television monitor supplied to Atari by Motorola. Because the composite video signal sent to the monitor by the game control circuitry differs in certain important respects from the signal derived from commercial TV broadcasts, the picture appearing on the screen is unlike that of a home TV set and the monitor does not produce any sound,
3.2.3 PICTURE ON TV SCREEN: Instead of the more or less continuous shades of gray (between the extremes of black and white) seen ona home TV screen, the game’s composite video signal is constructed to produce only three video levels on the monitor TV screen, as follows:
- white (sometimes called bright white), {b) medium white (sometimes called gray), and (o)_ black. Also the horizontal scan lines on the screen (raster) will be more noticeable than those on a home TV. A commercial TV broadcast signal produces a picture having 525 lines, with interlace, from top to bottom on a TV screen. The game’s composite video signal, however, contains synchronization information that produces only about half as many lines, without interlace. On the game’s TV screen the playfield back-
ground is black video level. Video levels of the objects
appearing on the playfield are as follows: Car I— under control of the steering wheel and gas pedal on the left side of the cabinet—is white video level and Car ll—the other car—is medium white level. The oil
slicks—19 in all, some consisting of 3 dots and some of
6 dots—are medium white level. The flags—16 in all— are medium white level, except for the one lighted flag which will blink to white video level. The score numerals for Car | are white video level and those for Car tt are medium white. The player-selectable set of barriers—13 barriers in all—is white video level.
3.3. GAME SEQUENCE
3.3.1 OPERATING MODES: During use, the Crash ’N Score game can be described as operating in either of two modes, attract or play. Plugging the power cord into an active AC outlet energizes the game and it starts out in the attract mode. The game remains in the attract mode until a player deposits a coin and the coin clears the coin mechanism, at which point a signal derived from the coin mechanism causes the game to go into the play mode. The game remains in play mode until the game timer elapses, at which time the game reverts back to the attract mode (unless there is credit remaining in the credit accumulator).
3.3.2, ATTRACT MODE: During this mode both cars move across and interact with any obstacles that they may encounter. However, all player controls are inoperative and neither speaker produces any sound. Just after the game is first energized, both scores may be zero, or else random numerals may appear in one or even in both score displays. Car | and Car 1 will initially appear in random locations on the TV screen, and then will move in random directions through the playfield. One flag will blink, but no car can earn points during this mode. It may happen that both cars eventually find and lock into movement along certain straight-line paths that avoid all obstacles. These paths may run either horizontally or vertically. After completion of a previous play mode, each car will continue to move in the direction it was headed at the moment game time elapsed. Each car will then interact with any obstacles that it may encounter. However, player controls are disabled and no sounds are produced. The final scores from the previous play mode will remain showing until a new play sequence is initiated.
3.3.3 GAME SEQUENCE IN PLAY MODE: No game sequence can begin unless credit has been entered into the credit accumulator. Once this has been done, the player must depress one of the start push buttons
horiz. deflection MONITOR intensity ————— CONTROL CIRCUITRY Iv
vert. deflection:
= 1 audio
steering I-A MONITOR
composite video
STEERING
WHEEL steering I-B
backlighting PUSH
BUTTON ‘one player start
ed barriers BUTTON
PUSH |-—__two player start BUTTON backlighting GAME
CONTROL
CIRCUITRY
STEERING
WHEEL steering II-B
=> 2 audio GAS PEG Car Il gas
c , ‘ MECH coin mechanism #1
ci coin mechanism #2
MECH
FRONT PANEL
Figure 3-1 Block Diagram of Crash’N Score Game
in order to initiate game play. The game timer then begins to count down, and play ends when all the game time has elapsed. Details of the game sequence are given below.
- Credit Accumulator. The Crash ’N Score game features an internal electronic credit accumulator that can store as many as 15 credits. If one or more credits are remaining in this accumulator when game time elapses at the end of a play sequence, then the game stays in the play mode rather than changing over to the attract mode. To initiate a new play sequence, the player need only depress a lighted start push button. However, if no credits are remaining in the credit accumulator, then the game changes over to the attract mode as soon as game time elapses. A player must then deposit money in order to enter credit into the credit accumulator.
- Obtaining Credits. To change the game over from the attract mode to play mode, a player has to deposit one or more coins into a coin mechanism so that credit will be entered into the credit accumulator. Coins deposited at any time are recognized, but the credit accumulator is not able to store more than 15 credits at any one time. Under 1 credit/coin game structuring, one credit is entered into the coin accumulator each time a player deposits a coin and it clears the coin mechanism; under 2 credits/coin game structuring two credits are entered. Provided that the game is structured to allow
bonus credits, when in the play mode players also can
obtain credits by earning scores that reach or exceed certain levels. One credit will be added into the credit accumulator when a player’s score reaches the score achievement level set up in the game structuring (for example, 10 points, 20 points, etc.). Ina 2-player game each player can earn a bonus credit; this means that a maximum of two bonus credits could be given during a single play sequence in a 2-player game.
- Start Push Buttons and Barriers Push Button.
Neither start push button will be lighted during a play
sequence. At other times a start button is lighted only
when credit remains in the credit accumulator. The left-of-center push button (engraved with the words ONE PLAYER START) is lighted if one or more credits remain in the credit accumulator, and the right-ofcenter push button (engraved TWO PLAYER START) also is lighted if two or more credits remain. Whenever at least one start push button is lighted, the unlighted barriers push button is made operative. If barriers are visible on the TV screen, depressing the barriers push button will cause them to disappear. Conversely, if they are not visible, then depressing the barriers push button will cause them to appear. The barriers push button is only operative when one or both start push buttons are lighted; it is not operative during the attract mode or while the game timer is counting down.
When a player depresses a lighted start push
button, the game timer begins to count down and the game responds as follows:
- Both score displays are reset to zero. (2). The steering wheel and gas pedal controls are made operative.
- The position of the white car (Car 1) is
changed; it will appear at the left edge of the of the screen. Ina1-player game the grey car
screen, halfway between the top and bottom, with the car pointing toward the center
(Car I) disappears. In a 2-player game the grey car’s position is changed to the right edge of the screen, halfway between the top and bottom, also with the car pointing toward the center of the screen.
- Each car’s engine sound starts to be produced by its speaker. In a 1-player game Speaker 2, the right-hand speaker, does not produce any sound because Car II is not appearing on the TV screen.
- The start push buttons cease to be lighted.
- Car Motion. Car speed and direction are under player control except for a few seconds after a car runs into an obstacle or into the opponent car. A car goes into a skid whenever it either runs into an
oil slick or collides with the opponent car; the amount
of car rotation and the distance traveled during a skid both are magnified in direct proportion to the car’s speed. Therefore a fast-moving car’s motion is more affected than is the motion of aslow-moving car. A car stops for a few seconds whenever it runs into either an unlighted flag or a barrier. Ifa car runs off the edge of the screen it disappears, but after a few seconds reappears at the opposite edge of the screen and resumes its travel on the playfield. A car’s motion is unaffected when it moves through alighted flag or if it should happen to cross into either score display region on the TV screen.
- Game Sounds. Sounds begin to be produced as soon as a lighted start push button has been depressed, and cease after the game time elapses. Throughout play the engine souns are heard separately for each car, with Car I’s engine sound being produced by Speaker 1 (on the left side of the cabinet) and Car Il’s sound by Speaker 2 (on the right), The engine sound will vary from “idle” speed, when the car is motionless and the player is not depressing the gas pedal, up through progressively higher-speed engine sounds as the car responds to gas pedal commands by moving faster and faster on the playfield. Other sounds produced separately for each car at various times during play can include the tire screech sound and the crunch sound. The tire screech sound is produced whenever the car runs into an oil slick obstacle and whenever a car collides with the opponent car. The crunch sound is produced whenever a car runs into either an unlighted flag obstacle or a barrier obstacle. Two additional game sounds can be produced by Speaker 1 only: a brief buzzing sound and a beeping sound. The buzzing sound is heard each time a point is scored
by either car. For example, if Car Il drove through a lighted flag having a numeral “3”, then Speaker 1 would produce three brief buzzing sounds. If the game is structured to allow earning bonus credits, then Speaker 1 will produce a beeping sound as soon as either car’s score reaches the preselected achievement level (for example, 10 points, 20 points, etc.).
- End of Play. When the game timer finishes counting down, play ends. The final scores from the just-completed play sequence continue to be displayed, but player controls are disabled and no sounds are produced. Car motion continues, however, and interactions with obstacles and with the ‘opponent car are unaffected. But no additional score points will be added and the scores will not be reset until a new play sequence is initiated. If at least one credit remains in the credit accumulator, then the ONE PLAY START push button will light up; if two or more credits remain, then the TWO PLAYER START. push button will light up also.
3.3.4 OWNER/OPERATOR OPTIONS: The Crash’N Score game features three options that allow the owner/operator to structure the game play—that is, change some of the rules or alter the game time— at the game site. All three options are simple manual adjustments and are physically located on the printed circuit board inside the game cabinet.
- Coin Credit Option. The 1 credit/coin— 2 credits/coin option consists of a two-position, slide
switch. When the slide is put in one position, the game
is structured to enter one credit into the credit accumulator each time a coin is deposited and clears either coin mechanism. When the slide is put in the other position, two credits are entered into the credit accumulator for each coin deposit. Subparagraph 4.3.1 in Section IV of this manual gives instructions for making this adjustment
- Length of Game Time Option. This option consists of a potentioneter (Trimpot) that has a stud projecting out from the top. This stud can be moved with the finger and then left in a new position that causes the game time to increase or decrease (within the minimum and maximum limits listed in the Specifications in Section I!), as desired. Subparagraph 4.3.2 gives instructions for making this adjustment.
- Bonus Credit Option. This option consists of a miniature switch assembly that has four independent, side-by-side 2-position switches, When all four switches are set in their “off” positions, no bonus credits are awarded. When one or more switches are set in the “on” position, bonus credits will be given as soon as a player’s score reaches the achievement level programmed by that switch code, (for example, at 10 points, or at 20 points, etc.). Subparagraph 4.3.3 gives instructions for making this adjustment. 3.4 DETAILED TECHNICAL DESCRIPTION OF OPERATION
3.4.1. GENERAL COMMENTS: This paragraph 3.4 gives a component-level technical description of the game-s electronic circuitry, and the following drawings supplement the text: drawing number 004256 (in four sheets) is a schematic diagram of the circuitry located on the printed circuit board; drawing number A004256 is an assembly diagram showing locations of components mounted on the PCB; and drawing number 004218 is a schematic of the harness wiring. These drawings, along with a schematic diagram of the TV monitor's circuitry, are included in Section VII of this manual. On the PCB and on its schematic each integrated circuit device location is identified by a column letter designation (A thru R) and by a row number designation (1 thru 10). On the PCB schematic the symbol “P” (which appears at various inputs to logic gates and other integrated circuits) indicates a connection to +5 volts through a pull-up resistor. The design of the car control circuitry is virtually identical for both cars; sheet 3 of the PCB schematic covers Car | and sheet 4 covers Car II. The main differences between these two sheets are:
- The signals 2 PLAYER and 2 PLAYER appear on sheet 4 (in zone C4). During a 1-player game these signals prevent Car Il from appearing on the TV screen and disable Speaker 2.
- The signals FREE GAME TONE and SCORE TONE appear on sheet 3 (in zone B3). They cause Speaker 1 to produce the beeping sound and the buzzing sound. Speaker 2 does not produce either of these sounds.
3.4.2 TV SYNCHRONIZATION INFORMATION (REFER TO PCB SCHEMATIC, SHEET 1 ZONES C,D 6 THROUGH 8): The output of a 14.3-MHz crystalcontrolled oscillator is passed through an inverter to produce the system CLOCK signal at A1 pin 2. This signal is applied to the horizontal countdown chain formed by the type-9316 devices in locations A2, C2 and B2. Here the frequency is divided by 908 for each video scan line on the TV screen (a horizontal sweep frequency of 15.76 KHz). In the vertical countdown, formed by the type-7493 devices in locations E1 and D1 and the type-74107 flip-flop FH1, the line rate is further divided by 263 for a video frame rate (vertical sweep frequency) of 60 Hz. This dividing-down in the countdown chains is done as follows. The horizontal countdown chain starts at a count of 116 (binary 0001110100) and advances to a count of 1024 (binary 1111111111). The H SYNC signal (horizontal sync pulse) begins at count 256 and is 64 clock
pulses wide (4.47 microseconds). H SYNC is produced
at pin 9 of flip-flop B3, where the rising edge of the 256H signal clocks a low through to the flip-flop’s Q
output pin. The Q output is set back to high by the 64H signal that later passes through gate A3 at pin 6 The vertical countdown chain starts at a count of zero (binary 000000000) and advances to a count of 262 (binary 100000110}, at which time a low appears at pin 12 of gate D3. This low is clocked through flip-flop B3 (with Q output at pin 5) at the next rising edge of the
512H signal. The V RESET signal then resets the vertical
countdown chain to zero. The counting cycle resumes after the V RESET signal is cleared again one horizontal scan line later. the V SYNC signal (vertical sync pulse) is produced at F1 pin 10 by the R/S flipflop formed by gate F1. The pulse begins with V RESET and is 41 scan lines long (290 microseconds). The H SYNC and V SYNC signals serve as the basis for the synchronization information sent to the TV monitor on the composite video signal.
3.4.3 PLAYFIELD GENERATION (SHEET 1 ZONES
B, C5 THROUGH 8): The stationary objects appearing
on the TV screen—flags, oil slicks and barriers—originate in contributions to the composite video signal derived from the PROMs (programmable read-only memories) in locations D2 and E2. Various signals coming from the horizontal and vertical countdown chains are applied to the Ay thru A; address inputs to the PROM in location D2, and cause D2 to produce the set of signals OB) 0 thru OBJ 3. These four signals are applied to the A, thru A; address inputs of PROM £2, and certain other signals from the countdown chains are applied to the A thru A; address inputs. The four signals produced at this PROM’s Ba thru By outputs are applied to a type-74153 multiplexer
device that produces a serial output at F2 pin 7. After
clocking with the 1H signal at flip-flop K3, the SHAPES
signal is produced at K3 pin 9. Certain combinations of the OBJ 1, OBJ2 and OB) 3 signals are then gated with the SHAPES signal to produce the following signals: FLAGS at H3 pin 6, SLICKS at H3 pin 3, and BARRIERS at H3 pin 11. The FLAGS signal goes to the white/black flag generator circuit (see subparagraph 3.4.12), which produces the white flag and black flag contribution to the composite video signal. The SLICKS signal serves as the oil slicks’ contribution to the composite video signal. The BARRIERS signal is gated at F3 pin 2 with the Q output from pin 9 of flip-flop J7. After further gating at F4 pin 6 and one inversion stage, the BARRIER VIDEO signal is produced at R3 pin 12. This signal serves as the barriers’ contribution to the composite video signal.
simple binary flip-flop. Provided the ATTRACT signal
is high (meaning that the game is not in the attract mode), and that the “Q” Latch is in its “reset” state (see subparagraph 3.4.6), the output at L8 pin 10 will be high. Signals applied at J8 pin 13 can then pass through the gate and clock flip-flop J7. The signals applied at J8 pin 13 come from the latch formed by Inverter J9. This latch “debounces” the signals produced by the front panel barriers push button and that reach the PCB via edge connector pins K and 10. This circuit arrangement insures that the barriers switch is disabled both during the attract mode and while the game timer is counting down.
3.4.4 COIN VALIDATION (SHEET 2 ZONES C, D 6 THROUGH 8): Each coin mechanism has an SPDT (single-pole, double-throw) switch that is activated
momentarily whenever a coin passes through the coin
mechanism and on into the coin box. Drawing number 004218, the harness schematic, shows how these are wired and how they connect to the PCB edge connector. On the PCB two inverter latches (at J9 pins 10 and 12 for coin switch #1, and at C10 pins 8 and 10 for coin switch #2), debounce the coin switch signals. The outputs from each latch are applied to a dual stage of flip-flops (formed by A7 for Coin Switch #1 signals, and by A8 for Coin Switch #2 signals) These dual stages are clocked by the 64V and 64V timing signals, respectively, and any latch output signal that is at least as wide as two cycles of the clocking signal will cause the second flip-flop stage to produce a pulse (COIN #1 at A7 pin 9, and COIN #2 at A8 pin 9). These pulses are used to set the “Q” Latch (see subparagraph 3.4.6) and to drive the coin counter (see subparagraph 3.4.5) The Q outputs from each second flip-flop stage are applied to individual flip-flop latch configurations, and both configurations are clocked by the 16V timing signal. If the owner/operator has set Switch $1 (the 1 credit/coin—2 credits/coin option switch) for 1 credit/coin structuring, pins 2 and 11 of gate P2 are connected via the switch contacts to +5 volts (through resistor R2). One pulse will be produced at P2 pin 12 each time a coin passes through Coin Switch #1, and at P2 pin 8 each time a coin passes through Coin Switch #2. If the owner/operator has set Switch $1 for 2 credits/coin structuring, however, the 4V timing signal (instead of +5 volts through resistor R2) is connected via the switch contacts to pins 2 and 11 of gate P2. With this arrangement two pulses will be produced at P2 pin 12 each time a coin passes through Coin Switch #1, and at P2 pin 8 for a coin through Coin Switch #2. The above pulses are ORed to produce the COIN signal at gate P3 pin 8. The COIN signal is one of the two inputs that drive the credit accumulator to count up (see subparagraph 3.4.8).
3.4.5 COIN COUNTER CIRCUIT (SHEET 2 ZONES 6 AND 7: The coin counter is an electromechanical counter that is mounted on the coin assembly access door. Drawing number 004218, the harness schematic, shows how this counter is connected to the PCB edge connector, the COIN #1 and COIN #2 signals pro-
10,
duced in the coin validation circuit (see subparagraph 3.4.4) are applied to pins 10 and 9 of gate MN1so that
a pulse is produced at MN1 pin 8 each time that acoin
passes through either coin mechanism and into the coin box. This pulse passes through inverter R3 and resistor R31 to the gate terminal of an SCR, bringing the SCR into conduction. The SCR current causes the coin counter to advance by one count each time that the SCR goes into conduction.
3.4.6 “Q” LATCH (SHEET 2 ZONES D 5 AND 6): Transistors QB and Q9 form a discrete component latch.
- Latch reset, with neither transistor conducting, meaning that the game is in the attract mode.
- Latch set, with both transistors conducting, meaning that the game is in the play mode: game timer is counting down or else game time has elapsed but one or more credits are remaining in the credit accumulator. The signal Q, produced at pin 10 of inverter E10, is high when transistor Q8 is conducting, and is low when Q8 is not conducting. The “Q” Latch is set either when diode D25 is forward-biased by a COIN #1 signal pulse to low, or when diode D26 is forward-biased by a COIN #2 signal pulse to low. These two signals are produced by the coin validation circuit when players deposit coins (see subparagraph 3.4.4). Normally the “Q” Latch is reset when pin 3 of Gate B5 is low, because this low interrupts the flow of base current to transistor Q8, causing it to go out of conduction. The low at B5 pin 3 is produced when the END GAME signal is high (meaning that game time has elapsed) at the same time that the 1 or 2 CREDIT signal is high (meaning that no credits are remaining in the credit accumulator). The “Q” Latch can also be reset should transistor Q7 go into conduction, also interrupting the base current flow to Q8. However, the antenna wire is connected directly to the base of transistor Q7 and a signal can be produced on this wire only by static discharge current flow.
3.4.7. “START” PUSH BUTTON SWITCHES (SHEET 2 ZONES A, B 6 THROUGH 8): The harness schematic drawing number 004218, shows how these switches are wired and how they connect to the PCB edge connector. Anytime that a player depresses either push button, ground is connected through the
switch’s contacts to the input of an inverter (at J9 pin 3
via edge connector pin 8 for the ONE PLAYER START push button, and at J9 pin 1 via edge connector pin 7 for the TWO PLAYER START. Each inverter output
connects to the “D” input of a flip-flop (at K4 pin 12
for the ONE PLAYER START and at K4 pin 2 for the
TWO PLAYER START). The 64V timing signal is applied
to the “clock” inputs of each flip-flop. However, the signal applied at the “D” input of the flip-flop will be ignored if a low is being applied at the flip-flop’s “Clear” input (K4 pin 13 and K4 pin 1). With the gating arrangement at L4 pins 12 and 11, a player depressing the ONE PLAYER START push button is ignored unless the 1 OR 2 CREDIT signal (applied at gate L4 pin 12) is low (meaning at least one credit is remaining in the credit accumulator), at the same time that the ATTRACT signal (applied at Gate L4 pin 11) is also low (meaning that either the “Q” Latch is reset or the game timer is not counting). Likewise, with the gating arrangement at L4 pins 3 and 2, a player depressing the TWO PLAYER START push button is ignored unless the ATTRACT signal (applied at gate L4
pin 3) is low at the same time that latch MN2 (applied The 1 CR START signal (from pin 8 of flip-flop K4)
at gate L4 pin 2) has been set (meaning that at least two. credits are remaining in the credit accumulator).
and the 2 CR START signal (from pin 6 of flip-flop K4)
are gated to produce the START signal at gate K5 pin 3. The 1 CR START and 2 CR START signals are also used to reduce the credit count in the credit accumulator (see subparagraph 3.4.8). The START signal is applied to the “D” input of the start flip-flop (at J7 pin 2). Clocking for this flip-flop is provided by ANDing the 32V timing signal with the flip-flop’s Q output. Note that the flip-flop can respond to clocking only when the signal applied to the “Clear” input (J7 pin 1) is high (meaning that the “Q” Latch has been set and the game timer is not counting down).
3.4.8 CREDIT ACCUMULATOR AND LAMP DRIVERS FOR “START” PUSH BUTTONS (SHEET 2 ‘ONES C, D 2 THROUGH 4): The type-74193 device in location P4 serves as a binary up/down counter that operates between count 0 and count 15. Clock pulses applied at P4 pin 5 will cause the counter to count up; the “up” pulses are produced at Gate N4 pin 1 by ORing the COIN signal (coming from the coin validation circuit, see subparagraph 3.4.4) with the BONUS. COIN signal (coming from the bonus credit circuit, see subparagraph 3.4.11). Clock pulses applied at P4 pin 4 will cause the counter to count down; the “down” pulses are produced at gate MN1 pin 3 by ANDing the 1 CR START signal and the signal resulting from ORing the 8V timing signal with the 2 CR START signal. With this clocking arrangement, credits are entered into the coin accumulator when coins are deposited into the game and when players earn bonus credits, and credits are removed when players depress the start switches. The connection from P4 pin 12 to P4 pin 11 prevents the type-74193 counter from “wrapping around” to zero, should additional credits happen to be entered after count 15 has been reached. The counter data outputs (P4 pins 3, 2,6 and 7) are decoded to produce the 2 CREDIT signal at inverter R3 pin 2, and the 1 OR 2CREDIT signal at gate P3 pin 3.
The 2 CREDIT signal connects via resistor R65 to the gate terminal of the SCR that drives the backlighting lamps behind the TWO PLAYER START push button. Likewise, the 1 OR 2 CREDIT signal connects via resistor R71 to the gate terminal of the SCR that drives the backlighting lamps behind the ONE PLAYER START push button.
3.4.9 GAME TIMER (SHEET 2 ZONES C5 AND 6): The type-555 device in location R10 and the type-7490 divide-by-10 decade counter in location P10 form the game timer. The type-555 device is connected as a very low frequency oscillator, but the END GAME signal (applied at R10 pin 4) prevents it from producing an output until a play sequence is initiated. The START signal applied at P10 pins 2 and 3 resets the type-7490 counter to count0 after a player depresses a lighted start push button. This count 0 pulls the END. GAME signal (produced at P10 pin 11) low. The type-555 device’s output at R10 pin 3 is used to clock the type-7490 counter; each oscillation from the type-555 device causes the counter to advance by one count. When the counter reaches a count of 6, the 8Fl timing signal (applied at F10 pin 11) is allowed to pass through the gating to produce the FLASH signal (at F10 pin 8). This FLASH signal connects to the score display circuit (see subparagraph 3.4.10) and causes the score numerals to blink during the fast one-eighth of the game time. When the counter reaches a count of 8, the END GAME signal is brought high and the END GAME signal (produced at inverter N10 pin 10) goes low. The END GAME at low prevents the type-555 device from producing an output. The END GAME signal is used in the start push button circuit (see subparagraph 3.4.7) as one of the conditions for clearing the attract flip-flop. The potentiometer R4 provides the game time option. By manually adjusting this potentiometer, the owner/operator increases or decreases the type-555 device’s oscillation frequency, with the result that the total game time is shortened or lengthened.
3.4.10 SCORE REGISTERS AND SCORE DISPLAY (SHEET 1 ZONES D 2 THROUGH 5): The type-7490 decade counter devices in locations L1 and L2 form Car I’s score register, and the type-7490 decade counter devices in M1 and M2 form Car II’s score register. Both registers are reset to zero when the START signal goes high. Clocking for Car I’s score register is provided at L1 pin 14 by the SA signal (coming from the Hit 1 detector, see subparagraph 3.4.12), and clocking for Car Il’s score register is provided at M1 pin 14 by the SB signal (coming from the Hit 2 detector). The four most significant data bit outputs from each register—the signals 1E through 1H from Car I’s register, and 2E through 2H from Car II’s register— are connected to the bonus credit circuit (see subparagraph 3.4.11). All 16 data outputs from the score registers—the signals 1A through 1H and 2A through 2H—are connected to two type-74153 multiplexer devices in locations K1 and K2. The timing signals 32H and 256H are applied to the multiplexer address inputs (K1 and K2 pins 14 and 2). The four multiplexer outputs are applied to a type-7448 BCD-to-7-segment decoder device in location J1, and the FLASH signal is applied at the blanking input (J1 pin 4). With this arrangement, the score numerals appearing on the TV screen are made to blink when the FLASH signal changes back and forth from low to high at a very slow rate. The 7-segment decoder’s outputs—the signals a through g—are applied to a pair of type-9312 devices
in locations J2 and H1. Various timing signals from the J2 pin 15 and H1 pin 15) are ORed to produce a seri
horizontal and vertical countdown chains are also applied to these devices, and their two outputs (at J2 pin 15 and H1 pin 15) are ORed to produce a serialized score signal (at Gate H2 pin 13). After synchronization with the 1H timing signal in flip-flop K3 and gating with the 256H signal, the WHITE SCORE signal is separated out at gate H2 pin 4 and the BLACK SCORE signal is separated out at H3 pin 8. Note that when the SCORE WINDOW signal, applied at the “Clear” input of the flip-flop (K3 pin 4) is low, the serialized score signal will not be clocked through the flip-flop. The SCORE WINDOW signal is produced at gate F1 pin 1 by decoding various timing signals coming from the horizontal and vertical countdown chains. The WHITE SCORE and BLACK SCORE signals
serve as the score contribution to the composite video
signal sent to the TV monitor (see subparagraph 3.4.19), 3.4.11 BONUS CREDIT CIRCUITRY(SHEET 2 ZONES A, B 3 THROUGH 5): The type-7486 exclusive-OR gates in location L3 pair up the four most significant
data bit outputs from Car I’s score register (the signals
1E, 1F, 1G and 1H), with the corresponding four switch
contacts from $2, the bonus credit option switch. When the state set up by a switch—either a low produced by connecting ground through the switch contacts, or else a high produced by #5 volts coupled through a resistor—matches the state of the respective score register output, the exclusive OR gate will produce a low at its output. For example, when input pin 4 of gate L3 is connected to ground because switch Ax is closed, a low will be produced at output L3 pin 6 only if the 1E signal is also low. Conversely, when a high is applied through R128 to the input pin 4 of gate 13 because switch A, is open, alow will be produced at output L3 pin 6 only if the 1E signal is also high. If the score in Car I’s score register reaches the achievement level set up in switch $2, then a signal is produced at gate N3 pin 8 that sets latch N2 at pin 1. The latch output at N2 pin 4 goes high and clocks the type-74107 J/K flip-flop at P1 pin 12, causing the flipflop's Q output (at P1 pin 2) to go low. When the H RESET signal (applied at the “clear” input, P1 pin 13)
goes low, the Q output is forced back high. This change of state from high to low to high again produces a pulse at the output of gate P3, pin 6, the BONUS COIN signal. This signal causes the credit accumulator to count up by one count (see subparagraph 3.4.8). The design for sensing the Car II score is identical to that for Car I. The type-7486 exclusive OR gates in location M3 pair up the four most significant data bit outputs from Car II’s score register (the signals 2E, 2F, 2G and 2H), with the corresponding four switch contacts from $2. If the Car Il score reaches the achievement level, then a signal is produced at gate N3 pin 6 that sets latch N2 at pin 10. The latch output at N2 pin 9 goes high and clocks flip-flop P1 at pin 9, causing
P1 pin 6 to go low. When H RESET goes low, P1 pin 6
is forced back high. This change of state produces a BONUS COIN pulse. The BONUS COIN signal also connects to pin 12
of the type-9602 retrigerable multivibrator (one-shot)
in location R1. A pulse transition at pin 12 causes the device to produce an output pulse whose width is determined by the R-C combination R1 and C4. After gating with the 4V timing signal, the FREE GAME TONE signal is produced at gate MN1 pin 6. This signal is the beeping sound contribution to the sound summing circuit (see subparagraph 3.4.23)
3.4.12 WHITE/BLACK FLAG GENERATOR, HIT DETECTORS AND SCORING SIGNAL CIRCUIT (SHEET 1 ZONES C, D 3 THROUGH 5):
- White/Black Flag Generator. The type-7493 binary counter in location A4 and the type-7485 4-bi magnitude comparator in location B4 form the circuit that selects which of the flags on the TV screen is to be lighted (that is, to blink). When the type-555 oneshot C1, Q output pin 3, applied at the pin 9 input of gate E4 is low, the CLOCK signal (applied at E4 pin 10) is blocked and a steady high is produced at E4 pin 8. This steady high is applied at A4 pin 14, insuring that counter A4 will not change state while HIT is low. In the type-7485 comparator B4 the counter’s four output signals are compared with the four 128H, 256H, 64V and 128V signals from the countdown chains (see subparagraph 3.4.2). The signal produced at the comparator’s output at B4 pin 6 goes high whenever the four pairs of signals applied to the comparator are all equal. The gating of the comparator’s output signal with the FLAGS signal produces the WHITE FLAG signal at gate A3 pin 11; gating with the FLAGS signal produces the BLACK FLAGS signal at gate N4 pin 13. The FLAGS and FLAGS signals come from the playfield generation circuit: see subparagraph 3.4.3.
- Hit Detectors. If Car 1 drives through the lighted blinking flag, a signal is produced at gate J4 pin 6 that triggers the type-9602 retriggerable multivibrator (one-shot) in location H4, causing it to produce the HIT 1 signal at H4 pin 6 and HIT 1 at H4 pin 7, for the duration of the multivibrator output pulse. Likewise, if Car II drives through the lighted flag a signal is produced at J4 pin 8 that triggers a second multivibrator in location H4, causing it to produce the HIT 2 signal at H4 pin 10 and HIT 2 at H4 pin 9, for the duration of the multivibrator output pulse.
The HIT 1 and HIT 2 signals are applied to the
inputs of exclusive OR gate D4 and the HIT signal is produced at D4 pin 6. The HIT signal goes to high whenever either multivibrator is triggered by a car driving through a lighted flag (see above paragraph). The HIT signal going high clocks device DE1. Q is a negative-going pulse with a dual function: 1) a load pulse for score counter £3, and 2) a trigger for the type-555 one-shot C1. The one-shot C1 signal at high allows the MFI signal to pass through gate E4 and drive counter A4 at pin 14, causing the counter to count at the MFI rate until the multivibrator pulse time elapses. This counting interval leaves counter 4 at some new, randomized state, causing some random flag on the TV screen to light up.
- Scoring Signal Circuit. The type-74192 decade up/down counter device in location E3 provides the means for generating a series of score pulses that correspond to the numeral showing in the lighted flag. For example, if a car drives through a lighted flag having a numeral 5, this counter clocked at 2 Fl’s rate will produce a series of five pulses at its output at £3 pin 3. The counter’s output signal is gated with a signal produced at E4 pin 11, where the 1FI signal (applied at E4 pin 12) is gated with the product of ANDing GT, and GT, from the game timer (see subparagraph 3.4.9). The GT, and GT signals are both high only during the last one-eighth of the game time.
This means that the 1Fl signal (which originates in Car
I's frame counter, see subparagraph 3.4.13), passes through gate E4 only during the last one-eighth of the game time. The result of the gating at F3 pins 13, and 12 is that the signal produced at F3 pin 11 will represent normal (undoubled) score points during the first seven-eighths of the game time, and doubled points during the last one-eighth of the game time. This signal produced at F3 pin 11 is ANDed with the 8V signal to produce the SCORE TONE signal (at F3 pin 8) that serves as the buzzing sound contribution to the sound produced by Speaker 1. The signal produced at F3 pin 11 also is gated with HIT 1 to produce the SA signal (at E4 pin 3) that clocks Car I’s score register, and with the HIT 2 signal to produce the SB signal (at E4 pin 6) that clocks Car Il’s score register (see subparagraph 3.4.10). When the ATTRACT signal, applied at Counter £3’s “up count” clock input (E3 pin 5), is held low, the counter is prevented from counting. This means that no points can be scored during the attract mode, even if a car should happen to drive through a lighted flag. When ATTRACT is high, the counter is free to respond to the signal applied at the “down count” clock input
(£3 pin 4). The “D” input (pin 12) of flip-flop DE1 is tied to +5 volts through a resistor. When a car drives through a lighted flag, the HIT signal (applied at the clock input (pin 11) of flip-flop DE1) goes from low to. high, causing a low to appear at the “Q” output (DEI pin 8). This low is applied to pin 11 of Counter £3 and causes it to preset to an initial counter state set up by the GND, OBJ 0, 08} 1 and OB} 2 signals applied at £3
pins 15, 11, 10 and 9, respectively. The Counter E3 then (applied at £3 pin 4), until counter state 0 is reached,
counts down, at a rate determined by the 4F1 signal
at which time a low is produced at the counter’s “borrow” output (E3 pin 13). The borrow signal is tied back to gate F3 pin 5, and when low it blocks the 4Fl clocking signal. Also, the borrow signal is passed through inverter J3, to reset flip-flop DE1 via the “clear” input (DE1 pin 13). With this circuit design the number of pulses produced at E3 pin 3 while the
counter is counting down corresponds to the numeral
in the lighted flag.
3.4.13 _GAS PEDAL SIGNALS AND PROCESSING OF ACCELERATION SIGNALS (SHEET 3 ZONES B, C 6 THROUGH 8 FOR CAR I; SAME ZONES ON SHEET 4 FOR CAR Il):
- Gas Pedal Signals. A SPDT switch is mounted on each gas pedal. The harness schematic, drawing number 004218, shows how these switches are wired and how they connect to the PCB edge connector at pin U for Car I’s gas pedal and at pin 17 for Car II’s
gas pedal. When a player depresses the gas pedal, the
respective edge connector pin is connected to ground through the switch contacts.
- Processing of Acceleration Signals. The following description applies to Car |; the design for Car Il is identical. The type-74193 up/down binary counter device in location E9, together with gate C9 and flip-flop C7 (Q” output at pin 3), form the acceleration counter for Car |. The count-up signal consists
and flip-flop C7 (Q” output at pin 3), form the accel of the acceleration pulses produced at gate F10 pin 12,
and the count-down signal consists of the deceleration pulses produced at gate C9 pin 3. The acceleration counter’s outputs are the signals SPEED ‘IL, SPEED 21, SPEED 31 and SPEED 41 (produced at £9
pins 3, 26 and7, respectively), and SPEED 51 (produced
at C7 pin 3). These give signals are called the speed code. The STOP | signal produced at gate C9 pin 6 goes high if the counter is at speed 0, if in the attract mode, or after Car | has run into an unlighted flag or a barrier (CRASH | signal is low). The STOP signal at high resets the counter outputs to zero. The type-7493 binary counter device in location D8 and flip-flop C7 (““Q” output at pin 5) forma frame counter. The type-7485 4-bit magnitude comparator device in location D9 and gate C9 (with output at pin
- form an acceleration comparator that compares the speed code—the five signals SPEED 1! through SPEED 5l—against the frame count bits—the five signals 1F| through 16F 1. The result of this comparison is the GOI signal produced at D9 pin 5. When the gas pedal is depressed the car will accelerate at the rate of one unit per 8 frames; when it is not depressed the car will decelerate at the same rate. The acceleration counter £9 counts these acceleration units. At speed 30 (counter binary output 11110), a signal produced at gate E8 pin 6 blocks out further acceleration pulses and the car will attain a maximum speed. Figure 3-3 shows the time relationship between the frame counter’s output signals (1F through 16F) and waveforms of the GOI signal at all speeds from 0 (stop) through 30 (full speed)
FRAME SIGNALS
“Gor SIGNAL (stop)
FOR ALL SPEEDS
(FULL SPEED) 30 ur L
Figure 3-3 2 TST 4B I Pt [a rs a ce 16F
Frame Counter Output Signals and Waveforms for GOI Signal
3.4.14 CAR STEERING SIGNALS AND STEERING PROCESSORS (SHEET 3 ZONES C, D 6 THROUGH 8 FOR CAR 1; SAME ZONES ON SHEET 4 FOR CAR II):
- Steering Signals. These signals originate on two small printed circuit boards—one for each steering wheel—that plug into the steering wheel assemblies mounted on the backside of the front panel (see item 7 on drawing number A000598-Xx). The steering PCB remains stationary when a player turns a steering wheel. A slotted hub is bolted onto the end of each steering wheel shaft and the hub’s
teeth move through a curved gap on the steering PCB
as a player turns the steering wheel. A pair of LED (light-emitting diode) light sources is positioned on one side of this gap, and directly opposite on the other side is a corresponding pair of phototransistors. Sheet 1 of drawing number A000607 shows mechanical details and the component layout on the Steering PCB. Anytime a player rotates a steering wheel in either direction, the circuitry on that steering PCB optically senses the hub slots and teeth as light emissions to the phototransistors are alternately blocked and cleared. Each steering PCB produces a pair of signals in quadrature; these signals are sent to the main game PCB via edge connector pins $ and 15 for Car |, and via pins T and 16 for Car Il. The wiring connections are shown on the harness schematic, drawing number 004218. On the main PCB, steering processors—one for each car—decode each pair of quadrature signals into car rate and direction of rotation information.
- Steering Processors. The following descrip-
tion applies to schematic sheet 3 (for Car 1). The design
for Car Il, shown on sheet 4, is nearly identical. The type-74193 up/down binary counter devices in locations F8 and H8 form the steering processor for Car |. The type-7474 dual flip-flop device in location H9 and gate F9 decode the two clocking signals that drive this steering processor. The VTC | signal and its complement VTC | serve as maximum turning rate signals. When Car | goes into a skid—either because it ran into an oil slick or into Car II—the signal produced at gate F9 pin 8 forces the car to be turned at the maximum turning rate for the duration of the SKID | signal. This can happen both in the attract mode and the play mode.
While the ATTRACT 1 signal is high, the signals during the play sequence the ATTRACT 1 signal
coming from the steering PCB are ignored, meaning that player steering control is disabled. However,
remains low, and the decoder circuit (flip-flop H9 and gate F9) can then translate the quadrature signal pair (coming from the left steering wheel) into direction and rate of turn information. The sample wave-forms shown in Figure 3-2 illustrate this translation. Diodes D13 and D14 are red LEDs that serve as visual indicators of the operation of the quadrature signal pair; these LEDs have no effect on the game and are provided as servicing aids only. The “right clock” signal (applied at F8 pin 5) causes the steering processor to count up, and the “left clock” (applied at F8 pin 4) causes it to count down. The type-74193 devices divide down the clock signals by 128. The output signals ROI (at F8 pin 6), R11 (at F8 pin 7), and R21, R3l and RAl (at H8 pins 3, 2 and 6, respectively), are the last five bits of the division by 128. These signals are called the rotation data and they form a rotation code that represents a total of 32 specific car orientations. For example, binary code 00000 represents the orientation with Car | pointing straight up. The code continues clockwise through 32 consecutive orientations up to binary 11111, which is just to the left of straight up. The type-7475 quad latch device in location H7 serves as the skid latch, and its four outputs D1 through D4l (at H7 pins 16, 15, 10 and 9, respectively) are called the direction code. When the SKID | signal is high, the skid latch’s outputs follows its inputs— the rotation code signals R1I through R4l coming from the steering processor. This direction code differs from the rotation code only when the car is in a skid. When the SKID I signal goes low (meaning that Car | is in a skid), the skid latch’s outputs are prevented from changing; instead the latch holds the most recent data from the steering processor. Therefore, during a skid the rotation code (signals ROI through R4l) tells in which direction the car is pointed, and the signal ROI plus the direction code (signals D1l through D4!) tell the direction along which the car moves while it is spinning or rotating rapidly.
3.4.15. MOTION CODE PROM (SHEET 3 ZONES C, D
5 AND 6 FOR CAR I; SAME ZONES ON SHEET 4 FOR
CAR II): The GOI signal—produced by processing acceleration/decelaration commands from the gas pedal (see subparagraph 3.4.13)—is applied to the “enable” input (pin 15) of the PROM in location F7. And the direction code data—the five signals ROI and D1 through D4l (see subparagraph 3.4.14)—are applied at the Ao through As address inputs of this PROM.The By through B, PROM outputs—produced at F7 pins 1 through 9~are called the motion code data.
The PROM is enabled whenever the GOI signal is
high. The motion code data then go to Car I’s horizontal and vertical motion counters (see subparagraph 3.4.16). The four By through B; signals of the
STEERING I (EC pin S)
STEERING 1 (EC pin 15)
VIC 1 (H9 pin 1)
RATE (H9 pin 6)
DIRECTION (H9 pin 9)
RIGHT CLOCK (F9 pin 3)
LEFT CLOCK (F9 pin 6) “TLS 1S 1 1 ee ee ee 5g Oe TITTTTTITTTTITTITTITTitTiit
a
a 2 a 0 a
Figure 3-2
motion code data pass through inverter stages and are
applied to the “preset” inputs of the vertical motion counter’s first stage (at D6 pins 3 through 6). The four B, through B, signals are gated with the V RESET 1 signal in gate E6, and the four gate outputs are applied to the “preset” inputs of the horizontal motion counter’s first stage (at ES pins 3 through 6). Table 3-1 shows the data applied at the preset inputs of the horizontal and vertical motion counters for each of the 32 directions in the direction code (the five signals ROI and D1l through D4l).
3.4.16 HORIZONTAL AND VERTICAL MOTION COUNTERS (SHEET 3 ZONES C, D3 THROUGH 5 FOR CAR 1; SAME ZONES ON SHEET 4 FOR CAR II): The type-9316 presettable binary counter devices in locations E5, D5 and C5 form Car |’s horizontal motion counter, and the type-9316 devices in locations Dé and C6 and flip-flop F5 (with “Q” output at pin 5) form its vertical motion counter. The CAR RESET | signal, produced at A6 pin 2 by inverting the CAR RESET I* signal (see subparagraph 3.4.17), resets both counters (at pin 1 of all type-9316 devices and at F5 pin 10). The CLOCK | signal, produced at A6 pin & {zone D6) by inverting the CLOCK signal, drives the clock inputs of all horizontal motion counter stages.
The signal produced at A6 pin 4 by inverting V CLOCK
drives the clock inputs of all vertical motion counter stages. The motion counters operate on the principle of Atari's “slipping counter” method of moving objects on a raster scan display (patent number 3,793,483). Both motion counters count in parallel with the synchronization countdown chains, (see subparagraph 3.4.2). To move an object in a vertical direction on the TV screen, the vertical motion counter is forced Sample Waveforms in Steering Decoder Circuit for Car |
to count short (for upward movement) or to count long (for downward movement), with respect to the horizontal countdown chain. Similarly, to move an object in a horizontal direction on the TV screen, the horizontal motion counter is forced to count short (for movement toward the left) or to count long (for movement to the right), with respect to the vertical countdown chain. The motion counters make a unit move in the
direction specified by the direction code—the signals
RO! and D1 through D4I—during each frame that the GOI signal is high and enables the motion code PROM (in location F7, see subparagraph 3.4.15). The signal CLOCK 1, which clocks the horizontal motion counter, is at the system clock rate of 14.3 MHz. The signal at A6 pin 4, which clocks the vertical motion counter, is two pulses per line and is gated out during vertical sync time, so that the vertical motion counter requires one less stage. This signal maintains the same amount of motion resolution in the vertical direction as in the horizontal direction. Certain outputs from the horizontal and vertical motion counters are gated to produce the CAR WINDOW | signal at gate B6 pin 8. The dimensions of the car window on the TV screen are 16 clock pulses
wide by 8 lines high. Certain outputs from the vertical
motion counter are gated to produce the VTC I signal (vertical terminal count) at B6 pin 6. This signal is used in the car steering processor circuit, (see subparagraph 3.4.14). The vertical motion counter’s final stage produces the 128CVI signal at F5 pin 5; this signal drives the frame counter (see subparagraph 3.4.13).
Table 3-1 Unit Motion Codes Into Motion Counters ***At D6 pins 6, 5, 4, 3 for Car |; at M6 pins 6, 5, 4, 3 for Car II **At E5 pins 6, 5, 4, 3 for Car 1; at NS pins 6, 5, 4, 3 for Car Il *AtH7 pins 9, 10, 15, 16 and F8 pin 6 for Car 1; at R7 pins 9, 10, 15, 16 and P8 pin 7 for Car Il STOP CODE 0100 1000 D4-D1, RO DIRECTION CODE*
Basa s aan na sn anincccoc ccc ccc coc CCS Bannan sco coe coe Ss soc eccos Ban neoc essa ooo OBS CoO Oss a cooS BAGO ato eat OO BBO OBB OO aso OB BOO A468 BSB Sao BSB OB OB eso OOO OHO OAS coco c Osan cc occ oC OC OCC CCC OCC SCOSCOCS Ba aA aA oo en sso CC OCC COSCO SOSCOOn COBB B BGO SOB BBA SOOO B AOC COC OC OBA Baoan noo eas seas SOs Go Sa OH HORIZONTAL COUNTER** DCBA
Bannan nncccc ecco coo DOC Oo Assan BOO COCO C OR SS COO oon SABA a coon AA CCC OCC OCC OMA OO OBA AAC Saar ot sess oss oc OSB OAs Oso aac VERTICAL COUNTER*** DCBA PRESENT INPUTS TO PRESENT INPUTS TO
3.4.17 CAR RESET CIRCUIT (SHEET 1 ZONE B4, FOR BOTH CAR I AND CAR II): This circuit produces two signals: CAR RESET I* and CAR RESET II*. At zone BS on sheet 3 the inverter A6 produces the CAR RESET | signal at pin 2; when low this signal resets Car I’s horizontal and vertical motion counters and steering
processor. Likewise, at zone B5 on sheet 4 the inverter
J6 produces the CAR RESET II signal at pin 2; when Jow this signal resets Car II’s horizontal and vertical motion counters and steering processor. The CAR RESET I* signal is produced at the “Q” output (pin 5) of the type-7474 flip-flop in location M4. The CAR RESET II* signal is produced at gate N4 pin 10 by gating the flip-flop’s “Q” output with a signal derived from certain signals from the horizontal countdown chain (see subparagraph 3.4.2) Flip-flop M4 is under control of its clock and “D” inputs only while the START signal (applied at M4 pin
- is high. Note that the flip-flop’s “D” input (pin 2) is tied to ground; this means that only binary 0 can ever be clocked into the flip-flop each time that the 256V timing signal (applied at the clock input, M4 pin 3) changes from low to high. While the START signal briefly goes low (after a player has depressed a lighted start push button), the flip-flop ignores the clock signal and instead is forced
to change to the state with the “Q” output (M4 pin 5)
at high and the “Q” output (M4 pin 6} at low. Assoon as the START signal goes back to high, the flip-flop is again allowed to clock in a low (from the “D” input
tied to ground) during the next low-to-high transition
of the 256V signal. This circuit design insures that the CAR RESET I* and CAR RESET II* signals briefly go high only once per play sequence, at the beginning just after a player depresses a lighted start push button.
3.4.18 CAR VIDEO PROCESSORS (SHEET 3 ZONE C2 FOR CAR I; SAME ZONE ON SHEET 4 FOR CAR II): The type-9312 device in location H5 and the 4K ROM in location F6 form the video processor for Car I. Inputs to the ROM include rotation information (the signals RO1 through R41 rotation code from the steering processor, see subparagraph 3.4.14), line information (the signals LO1 through L21 from the vertical
motion counter), and column information (the signals subparagraph 3.4.16). The ROM’s eight output signals,
€31 and C41 from the horizontal motion counter, see
along with additional column information (the signals
COI through C2I from the horizontal motion counter), are applied to the type-9312 device to multiplex the ROM data serially onto the complementary pair of signals produced at HS pins 14 and 15. The CAR
WINDOW I signal is applied to the “enable” input at
H5 pin 10. After clocking through flip-flop F5—to remove edge effects and to avoid race problems—the CAR | signal is produced at F5 pin 3. This signal serves as the car video contribution to the composite video signal sent to the TV monitor.
3.4.19 VIDEO SUMMING CIRCUIT (SHEET 1 ZONEB. 3 AND 4): The composite video signal is formed at the junction of resistors R23, R24, R33 and the anode of diode D12. The diode couples the synchronization information contribution produced at gate C8 pin 10 by gating the V SYNC and H SYNC signals coming from the countdown chains (see subparagraph 3.4.2}. The medium white (grey) video level contribution is produced at gate C4 pin 6 by gating the CAR 2 (Car I video), BLACK SCORE (Car II’s score numerals), BLACK FLAGS (unlighted flags) and SLICKS (oil slicks) signals. The white (bright white) video level contribution is produced at gate P2 pin 6 by gating the BARRIER VIDEO signal, the signal obtained by combining the WHITE FLAG signal with the 8FI signal (from Car I’s frame counter), and a signal derived from the CAR | and WHITE SCORE signals. Resistor R25 is included for use as a test point when servicing the game; no signal is applied at the “TEST” point during normal game operation.
3.4.20 ENGINE SOUND SYNTHESIZERS (SHEET 3 ZONES B 5 AND 6 FOR CAR |; SAME ZONES ON SHEET 4 FOR CAR I!): The configuration of inverterresistor networks connecting to the base of transistor Q10 performs a D-to-A (digital-to-analog) conversion of the SPEED 11 through SPEED 4I and the SPEED 5 I signals. Transistor Q1 acts as a current source that controls the oscillation frequency of the type-555 Timer with output at D10 pin 3. The type-7492 counter devices in locations B9 and B8 divide down the frequency of D10’s output signal by both 6 and 4. Signals representing various products of this division are mixed together through resistors R115 through R117; the resulting signal, MOTOR I, is the Car | engine sound contribution to the sound produced by Speaker 1.
3.4.21 CRASH AND SKID DETECTORS (SHEET 3 ZONES A 4 THROUGH 7 FOR CAR I; SAME ZONES. ON SHEET 4 FOR CAR Il):
- Crash Detector. As long as the signal produced at gate B5 pin 11 is high, the V RESET I signal applied at pin 3 of flip-flop A5 will clock in the steady high applied at the “D” input (pin 2) via a connection to +5 volts through a resistor. This will produce a high at the “Q” output (pin 5); the V RESET I signal will clock this high into the second “D” input (at AS pin
- during its subsequent low-to-high transition (at A5 pin 11). In this way both the CRASH SEQ | signal (produced at AS pin 9), and the CRASH | signal (produced at B5 pin 8), will be kept high The signal produced at gate B5 pin 11 goes low whenever Car | drives into an unlighted flag or a barrier. This low, applied to flip-flop A5’s Clear input (pin 1), causes the flip-flop to change to the state with
the “Q” output (pin 6) at high and the “Q” output (pin 5) at low, The high at A5 pin 6, together with the high still remaining at AS pin 9, causes the CRASH I signal to go low. The CRASH | signal goes back high just after the next low-to-high transition of the
V RESET 1 signal, because that signal transition will
have clocked a low into the flip-flop’s “Q” output at AS pin 9, the CRASH SEQ | signal. The CRASH | signal at low causes the Car | motion to stop (via the connection to gate C8 pins 11 and 12, zone C6), and also causes the crunch sound to be produced (via the connection to resistor R97 and diode D24). This arrangement keeps the CRASH SEQ signal low, preventing further crashes, until Car | no longer is in contact with the unlighted flag or barrier.
- Skid Detector. If the CAR | signal is high at the same time that the CRASH SEQ I signal is low (meaning that Car | has not crashed), then the SKID I* signal going high will bring gate B6 pin 12 low. This causes the type-555 timer device in location B7 to produce a one-half-second pulse at its output pin 3, the SKID I signal. The complement of this signal— SKID I— connects to the Car | skid latch at H7 pins 4 and 13 (zone C6) and prevents the latch from accepting new data from the Car I steering processor (see subparagraph 3.4.14). The SKID | signal also causes the “tire screech” sound to be produced (via the connection to pin 13 of inverter L10 in zone B4)
3.4.22, SCREECH AND CRUNCH SOUND SYN-
THESIZERS (SHEET 3 ZONES A, B 3 AND 4 FOR CAR I;
SAME ZONES ON SHEET 4 FOR CAR Il):
- Noise Generator. Transistor Q2 is an NPN specially selected for noise characteristics. The noise developed at its emitter is amplified by the LM324 (output at pin 1) in location C11
- Screech Sound Synthesizer. The LM324 operational amplifier (with output at pin 14) in location C11 is configured as a free-running multivibrator that is perturbed—via coupling through capacitor C51 and resistor R106—by the noise originating from transistor Q2. This noise imparts a “gritty” quality to the signal. The SKID | signal applied at pin 13 of inverter L10 turns the amplifier on and off via the connection to C11 pin
- The resulting signal that is coupled through R125 represents the Car “tire screech” contribution to the
sound produced by Speaker 1
- Crunch Sound Synthesizer. When the CRASH | signal—applied at the junction of resistor R97 and the cathode of diode D24—goes low, the discrete one-shot formed by transistor Q3 and the M324 amplifier (with output at C11 pin 7) is triggered. Noise is imparted via resistor R100 and the resulting signal coupled through resistor R110 represents the Car I “crunch” contribution to the sound produced by Speaker 1. 3.4.23 SOUND SUMMING CIRCUITS (SHEET 3 ZONES B 2 AND 3 FOR SPEAKER 1; SAME ZONES ON SHEET 4 FOR SPEAKER 2):
- Speaker 1. The junction of resistors R110 and R122 through R125 forms the sound summing point where the following five analog signals are mixed:
- Car I’s engine sound—the MOTOR I signal— coupled through R122: see subparagraph 3.4.20.
- The “crunch” signal coupled through R110 whenever Car | drives into an unlighted flag or a barrier: see subparagraph 3.4.20 (a).
- The “tire screech” signal coupled through R125 whenever Car I goes into a skid: see subparagraph 3.4.20 (b).
- The “beeping” signal—FREE GAME TONE— coupled through R123 whenever either car's score reaches the preselected score achievement level: see subparagraph 3.4.11.
- The “buzzing” signal—SCORE TONE— coupled through R124 whenever either car drives through a lighted flag: see subparagraph 3.4.12 (c). The analog signal developed at this summing point is coupled by capacitor C62 to the Speaker 1 audio amplifier stage formed by the LM324 with output at C11 pin 8. The potentiometer R109 provides the volume adjustment for the sound produced by Speaker 1
- Speaker 2. The junction of resistors R56, R58 and R63 forms the sound summing point where the analog sound signal for Speaker 2 is developed. Note that only three analog signal contributions are mixed here: Car Il’s engine sound (MOTOR Il), the “crunch” signal for Car Il and the “tire screech” signal for Car Il. The potentiometer R57 provides the volume adjustment for the sound produced by Speaker 2.
3.4.24 SPEAKER DRIVER STAGES (SHEET 3 ZONES B 1 AND 2 FOR SPEAKER 1; SAME ZONES ON SHEET 4 FOR SPEAKER 2): The LM380 amplifier in location B10 serves as the output driver stage for Speaker | (via edge connector pin V). Resistor R105 couples the audio amplifier’s output to the driver stage via Capacitor C54. The ATTRACT signal applied at pin 11 of inverter L10 insures that Speaker 1 does not produce any sound during the attract mode. Likewise, the LM380 in location K10 serves as the output driver stage for Speaker 2 (via edge connector pin L). Resistor R46 couples the audio amplifier’s output to the driver stage via capacitor C14. The signal produced by inverter L10 at pin 4 insures that Speaker 2 does not produce any sound either during the attract mode, or during a one-player game.
IV. Installation Instructions
4.1 UNPACKING INSTRUCTIONS
4.1.1 EXAMINATION FOR SHIPPING DAMAGE: Before shipment from the factory, components and sub-assemblies of each game are carefully checked for proper operation, However, during shipment some adjustments may have changed or parts may have been damaged. Upon initial removal of the game from the shipping container, first examine the exterior of the cabinet. Then open the rear panel access door and also examine the interior. Any shipping damage such as a dented, cracked or broken cabinet, sub-assemblies broken loose, etc., should be reported immediately to the shipper and to Atari, Inc.
Be sure to confirm that both steering wheels turn
smoothly, both in the clockwise and counterclockwise directions. There are no limit stops; the wheels are free to turn continuously in either direction. Also operate both gas pedals and confirm that their movement is smooth, and that the return springs force the pedals back to their initial positions. 4.1.2. MECHANICAL INSPECTION: After determining that the game has been received in good condition, carefully inspect the interior parts and verify the following:
- Allslip-on and plug-in connectors are firmly seated (particularly the PCB edge connector.
- The fuses are all seated in their holders
- No loose foreign objects are present (especially metal objects which could cause electrical short circuits)
- No harness wires have become disconnected or pulled loose. Do not go on to the remaining paragraphs in this section until the above mechanical inspection has been thoroughly performed.
4.2, ENERGIZING THE GAME
4.2.1 APPLICATION OF AC POWER: Close the rear panel access door, making sure that it is completely shut at the bottom, and remove the key from the lock. Plug the power cord into an AC outlet providing the AC power listed in the Specifications (Section II of this manual). The wall outlet must accept a threeprong plug and the receptacle must be connected to a good earth ground, After the power cord has been plugged in, the proper response from the game is that a picture will appear on the TV screen. If there is no response at all from the game, unplug the power cord and check the AC wall outlet. A simple, safe way to check for presence of AC power at the wall outlet is to plug in an appliance known to be working properly—such as a table lamp, radio, or an electric clock. If the wall outlet passes the check, then presume that the trouble is with the game and refer to Section VI of this manual.
Do not go on to the remaining paragraphs in this section until the proper response described above has been observed.
4.2.2 CHECK ON OPERATION OF INTERLOCK SWITCH: The interlock switch is a safety switch mounted inside the cabinet, near the bottom edge of the rear panel access door. At the factory this switch is mechanically adjusted so that it will automatically transfer to its “off” position (switch contacts open)
whenever the rear panel access door is opened. When
the interlock switch is in its “off” position, the AC power leading to the game’s power supply is interrupted. When the access door is closed, the interrupt switch is adjusted to be in the “on” position (switch contacts closed) and AC power is allowed to reach the game's power supply, meaning that the game can operate. After application of AC power per paragraph 4.2.1 above, correct operation of the interlock switch can be checked as follows: unlock the rear panel access door and slowly open the door. The correct response is that by the time the edge of the door has
moved about 2 to 3 inches away from the cabinet, the
TV screen should go dark, verifying that the interlock switch has automatically transferred to “off”. While opening the access door do not insert fingers inside the cabinet, and do not allow foreign objects to fall inside. If the TV screen continues to be lighted up even after the door has been opened, immediately
close and lock the door, and unplug the power cord
from the wall outlet. Then refer to Section VI of this manual to replace and/or adjust the interlock switch Do not go on to the remaining paragraphs in this section until the operation of the interlock switch has been checked and found to be correct.
4.3, GAME STRUCTURING
Before putting the game into operation at the game site, the game structuring should be defined by the owner/operator. The term “game structuring” refers to the game rules, the length of each game, and other variable features. Paragraph 3.3.4 of Section III in this manual covers the owner/operator options featured in this game and describes how they affect the game structuring. In the Crash 'N Score game all three options are simple manual adjustments: setting the position of a slide switch; moving a stud on a potentiometer body; and setting the positions of four side-by-side 2-position switches. All these adjustments are performed on the printed circuit board inside the
game cabinet. Before performing any adjustment, the game should be de-energized or not operating. Further, it is recommended that the power cord also be unplugged beforehand. Unlock and open the rear panel access door; doing this should cause the interlock switch to deenergize the game, as described in paragraph 4.2.2. If the switch fails to de-energize the game, immedi:
ately close and lock the door, unplug the power cord,
and refer to Section VI of this manual to adjust and/or replace the switch. While being careful to avoid touching any parts of the body against the TV chassis components or other wiring connections inside the cabinet, find the printed circuit board and examine its surface.
4.3.1 COIN CREDIT OPTION: Find the slide switch mounted near the edge of the PCB. The switch’s ap-
proximate location is shown in Figure 4-1, and its exact
location is shown as $1 on drawing number A004256 in Section VII of this manual. Note the words “1 PLAY” and “2 PLAY” engraved on the PCB alongside the switch body. First, to structure the game for 1 credit/coin, slide the stud on top of the switch all the way toward the word “1 PLAY” engraved on the PCB. To structure the game for 2 credits/coin, slide the stud all the way toward the word ‘2 PLAY”. Then cut out the “1” or “2” from the Instruction Plate Card (provided with this game) and using transparent tape, attach it to the inside of the silk-screened plexiglass in the appropriate area. Second, cut out the “10” from this card and attach it with transparent tape to the blank area in the silkscreened phrase “Bonus score value doubles in last “seconds.” The period in each game during which the player’s score blinks is not variable by the operator. After performing this adjustment, close and lock the rear panel access door and energize the game.
4.3.2. LENGTH OF GAME TIME OPTION: Find the potentiometer (Trimpot) mounted near the edge of the board, not far from the large, black heat sink. This potentiometer’s approximate location is shown in Figure 4-1, and its exact location is shown as R4 on drawing number A004256 in Section VII of this manual. Note the words “GAME TIME” engraved on the PCB alongside the potentiometer body. To shorten or lengthen the game time, move the stud on top of the potentiometer body in a direction as shown in that figure. After performing this adjustment, close and lock the rear panel access door and energize the game.
1234
1234
BONUS CREDIT SWITCH
2 PLAY ca} PLAY 5 MTR 2 = (| q g u & (increase +) a L ci °° eu
MTR 1
(increase | for these four pots) VOL. 1
Figure 4-1 Approximate Locations of Owner/Operator Options on Crash ’N Score PCB
4.3.3 BONUS CREDIT OPTION: Find the miniature switch assembly with four side-by-side switches that is mounted near the end of the board farthest from the edge connector. The switch’s approximate location is shown in Figure 4-1, and its exact location is shown as $2 on drawing number A004256 in Section VII of this manual. See also the detail below of this switch, Figure 4-2.
Towards center of PCB
14819 .,0f,, —> 1y8/2M ,,08,, —>
Figure 4-2 Detailed View of Bonus Credit Switch
Each of the four 2-position switches can be independently set to either an on” or an “off” position. A weighted value of score points is assigned to each switch, namely as below:
Point value: 10 20 40 80 Lever Number: 1 2 3 4
Push forward on any of the levers, so the pointed end of the lever faces down and that lever is in the “on” position. Pushing one or more of the levers “on” will cause their respective values to be added together. We suggest total values between 40 and 90 points. For example, to set the game for extended play after 50 points, push forward on levers #1 and 3.
4.3.4 ADJUSTMENT OF SPEAKER VOLUMES AND PITCHES: Each speaker's electronic drive circuit is provided with a potentiometer (pot) that controls the volume of sounds produced by the speaker, and another controlling the pitch. These potentiometers are independent of one another and each can be adjusted manually. All four pots are found near the edge-connector end of the PCB. Their approximate locations are shown in Figure 4-1 and their exact locations are shown as R109 and R57 on drawing number A004256 in Section VII of this manual. Note the designations VOL 1 and MTR 1 (for the left speaker) and VOL 2 and MTR 2 (for the right speaker) engraved on the PCB alongside the potentiometer bodies. To cause a speaker to produce louder or quieter sounds, move the stud on top of the potentiometers in the direction shown in Figure 4-1 for both speakers. First adjust Speaker 1’s volume for the desired level of the score buzzing and bonus credit sounds; then adjust Speaker 2so that the volume of Car 2’s engine
sounds match those of Car 1. Then adjust the pitch in
a similar fashion with the MTR 1 and MTR 2 pots.
4.4_ FUNCTIONAL CHECK OF GAME OPERATION
The following procedure provides a simple check that can be quickly performed at the game site and that does not require external test equipment. If at any point during this procedure the game’s response is observed to be other than the response called for herein, assume the game is not operating correctly and refer to Section VI of this manual. If all the responses are as described here, then all major parts of the game can be assumed to be functioning correctly. After performing the adjustments described in paragraph 4.3, Game Structuring, and in paragraph 4.2, Energizing the Game, the game should be operating in the attract mode, as per paragraph 3.3.2. The speakers should not be producing any sound. Observe the TV screen. 4.4.1 ATTRACT MODE: Just after the game is energized, near the top of the TV screen random numerals may be appearing in one or possibly in both score displays, or else both scores will be zero. Both cars should be moving across the screen. The cars should interact with any obstacles that they may encounter and also with each other. The various obstacles described in subparagraph 3.2.3 (oil slicks,
flags, and possibly barriers also) will be distributed at various locations throughout the playfield.
Look at the front panel. Neither start push button the barriers push button, both gas pedals, and by turn
should be lighted. Confirm that all player controls are disabled by depressing both start push buttons, the barriers push button, both gas pedals, and by turning both steering wheels. None of these actions should produce any response from the game.
4.4.2, OBTAINING CREDITS: Depress the coin rejector button on the coin mechanism of each coin acceptor; make sure that each linkage is operating smoothly. Deposit a coin in one coin mechanism; no genuine coin should be rejected. If the game is structured for 1 credit/coin, upon acceptance of this
first coin the game should respond by lighting up only
the ONE PLAYER START push button (meaning that one credit has been entered into the credit accumulator). If the game is structured for 2 credits/coin, upon acceptance of this first coin both start push buttons: should light up (meaning that two credits have been entered into the credit accumulator) Deposit a second coin in the other coin mechanism. If the game is structured for 1 credit/coin, doing this should cause the TWO PLAYER START push button to also light up (meaning that a total of two credits have now been entered into the credit accumulator). If structuring is for 2 credits/coin, no visible response to the second coin will be evident, but a total of four credits will have been entered into the credit accumulator. If the game is structured for 1 credit/coin, deposit a third and fourth coin so that a total of four credits will have been entered into the credit accumulator, Observe the TV screen. If barriers are present, depressing the barriers push button should cause them to disappear. Conversely, if barriers are not present, depressing the push button should cause them to appear. After confirming correct operation of this push button, make sure that the barriers are added before continuing with this procedure. Note that up to this point neither speaker should be producing any sound.
4.4.3 FIRST PLAY SEQUENCE: Depress the TWO PLAYER START push button. The game should respond as follows:
- Both score displays should reset to zero.
- Engine sounds should begin to be produced by each speaker. Initially both will be “idle” speed sounds.
- On the TV screen the cars should change over to their initial positions: white car at left edge of screen (halfway from top to bottom, with car pointed toward center of screen), and the grey car at the right (also halfway from top to bottom, with car pointing toward the center of the screen)
- Both start push buttons should cease to be lighted.
- The barriers push button will be disabled. Depress the gas pedal on the left side of the cabinet. The game should respond by causing the engine sound from Speaker 1 to speed up, and by causing the white car to begin to move toward the center of the playfield. While keeping the gas pedal depressed, turn the left-hand steering wheel in a clockwise direction. Doing this should cause the white car to turn to the right. Next turn the steering wheel in a counterclockwise direction; doing this should cause the white car to turn to the left. Release the gas pedal. The game should respond by causing the white car to slow down, and by causing the engine sound to also slow down. Eventually the car will come to a stop and the engine sound will return to idle. Next perform this same check for the grey car depress the gas pedal on the right side of the cabinet, turn the right-hand steering wheel in each direction, and release the gas pedal. Responses for the grey car should be similar to those for the white car. For the remaining game time maneuver each car individually so that it interacts with the opponent car and with each type of obstacle at least once. The skid, crunch and scoring responses—both visual and audible—should be as described in subparagraph 3.3.3, Game Sequence in Play Mode. After correct operation has been verified separately for each car, let the game time run out. During the last one-eighth of game time the score numerals should be blinking, and the number of points given
for driving through a lighted flag should be double duce any sound but the cars should continue moving,
the numeral shown in the flag. When game time finally runs out, both speakers should cease to pro-
starting from the positions they held at the moment the game ended. Also the final scores should remain showing.
4.4.4 GAME TIME ELAPSED, WITH CREDIT REMAINING: Confirm that the player car controls are now disabled: turning each steering wheel and depressing each gas pedal produces no response on the TV screen, But do not depress the barriers push button or either of the start push buttons. Look at the start push buttons. Both should now be lighted, because two credits had been left in the credit accumulator when the previous game se-
quence ended. These two were part of the four credits
entered prior to commencing that game sequence. While observing the TV screen, depress the barriers push button. Doing this should cause the barriers to disappear.
4.4.5 SECOND PLAY SEQUENCE: Depress the ONE PLAYER START push button. The game should respond as follows:
- Car 1, the white car, should change to a new Position at the left edge of the TV screen, half way between the top and bottom, with the car pointing toward the center of the screen. The grey car should disappear.
- The idle engine sound for Car t should begin to be produced by Speaker 1, but Speaker 2 will remain silent.
- The score for the white car should reset to zero, and the score for the grey car should disappear.
- Both start switches should cease to be lighted. One credit still remains in the credit accumulator, however. If the game is not structured to allow awarding of bonus credits, let the game time run out. When this happens, the ONE PLAYER START push button will light up. If the game is structured to allow awarding of bonus credits, then operate the steering wheel and gas pedal of Car | in order to earn points. As soon as
the number of points in the white score reaches the
preselected achievement level set up in the game structuring, the bonus credit beeping sound should be produced by Speaker 1. NOTE: To facilitate checkout of the bonus credit feature before depressing the start push button, it may be desirable to temporarily change the structuring to the lowest achievement level (10 points); doing this makes it easier to earn a bonus credit before the game time runs out. However, afterwards be sure to restore the structuring to
the original achievement level. Refer to subparagraph
4.3.3 for the procedure for changing achievement level setting. The bonus credit just awarded will be entered into the credit accumulator, meaning that a total of two credits are remaining. When the game time runs out, both start push buttons will then light up.
V. Maintenance and Adjustments
5.1 ROUTINE MAINTENANCE
Due to its solid-state electronic circuitry, this
Atari game should require very little maintenance and
only occasional adjustment.
5.1.1 CLEANING: Game cabinets and glass may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from distributors.
5.1.2 LUBRICATION: About once every three months lightly spray the rejector linkage portion of the coin acceptor inside the coin mechanism. Use WD-40® or similar lubricant, and avoid spraying the entire coin acceptor.
5.2, ADJUSTMENTS ON TV MONITOR
The TV monitor need be adjusted only when the picture is distorted, or if contrast or brightness seem out of adjustment
lines covering the screen just
barely disappear when the brightness turned up. CONT (Contrast}—Adjust so that the images are as bright as possible against the dark background without being blurred. HORIZ HOLD (Horizontal Hold)—Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture. VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture.
a ra
i]. m= e000 KHOo [3838 O90QOQ oO i FUSES CONT BRITE VERT HORIZ VOL HOLD HOLD
Figure 5-1 Location of Adjustments on TV Chassis
VI. Troubleshooting and Repair
6.1 GENERAL PROCEDURE
This section describes troubleshooting procedures in detail sufficient for a person with moderate technical ability to understand. However, for those interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator's Handbook, manual no. TM-043. This book is available from Atari, Inc, attn. Customer Service Dept., 2175 Martin Avenue, Santa Clara, CA 95050, for $5.00 each, or from your distributor.
6.1.1 IDENTIFYING THE TROUBLE AREA: The first
troubleshooting step should be to note all observable
trouble symptoms. Examples of symptoms are: depositing a coin produces no game response, no sound coming out of the speaker at any time, no picture on the TV screen. At the same time also note the game features that still work. A systematic way of checking game operation is to perform the functional check given in Section IV of this manual. Carefully train your eye to pick up all clues; by doing
this an experienced troubleshooter can often spot the
cause of a trouble even before he opens the cabinet. Keeping these observations in mind, use the understanding of game operation gained from the Theory of Operation (Section II!) and the schematic drawings (Section VII). Next narrow down the suspected cause of the trouble to a specific area or areas. of the game: the coin mechanism, TV monitor,
harness and front panel components (switches, lamps,
gas pedals, brake pedals, steering wheel), electronics tray, printed circuit board, and power cord. Be careful not to overlook possible trouble areas that may seem too obvious: a power cord plug that has worked loose from the wall outlet and is no longer fully seated in the receptacle, or a rear panel access door that is not fully closed (thus causing the interrupt switch to block the AC power path to the game).
6.1.2. LOCATING THE TROUBLE CAUSE: Once a problem has been narrowed down to one or more areas, the next step is to perform various tests and measurements to isolate a specific cause of the trouble. Remember that sometimes a very complicated problem, such as erratic game operation, can be traced to a simple cause—the printed circuit board not being fully seated in its edge connector, Start with the most suspect area and trace backwards from the point where the trouble is first observable, using a process of elimination to eventually locate the faulty component, connection, etc. For example, if no sound is audible during game play, first check for a signal at the speaker leads. If no signal is present there, go back through the wiring harness connections to the printed circuit board. If there is still
no signal, then systematically check back through the
various components of the sound generation circuit. Substitution of parts is a legitimate and easy way to isolate the cause. For instance, if the PCB is the suspected trouble area, remove it and substitute a known-to-be-good PCB. Then check for correct game operation. Similarly, to check the TV monitor, connect the game to a known-to-be-good monitor. The harness can often be checked by substitution also, Substitute both a known-to-be-good PCB and TV monitor. If the trouble still persists, the harness must be at fault. While locating the trouble cause, use the technical descriptions in Section II] as guides for correct circuit-level operations, and the schematic drawings of Section Vil as roadmaps for tracing signal flow paths. The test equipment for use in troubleshooting is discussed in paragraph 6.2.
6.1.3 CORRECTING THE TROUBLE CAUSE: In practice, the steps required to correct troubles can range from simple adjustments (fully seating the PCB in its edge connector, changing the setting on a potentiometer, adjusting the picture controls on the TV monitor) to repair of loose connections and replacement of defective parts. Extreme care should be exercised when removing integrated circuit devices and discrete components. Use a 40-watt soldering iron with a small tip designed especially for IC work. To remove an IC device, follow this procedure: Remove all solder from both sides of the PCB, first melting it with the hot iron and then sucking up the molten solder with a Soldapullt® solder sucker. After all the solder is gone, remove the IC device by gently prying up. Afterwards clean the area thoroughly, using an approved PCB cleaning solution to remove any traces of flux and dirt. Alcohol will do in a pinch, if necessary. Insert the new IC device using an IC insertion
tool, making sure that the reference notch is oriented
correctly and that the device’s leads are not bent during insertion into the board. Afterwards, be sure to solder each lead on both sides of the PCB, using as little solder as possible. After soldering, clean the area thoroughly to remove the flux. Observe the same removal and insertion procedures when replacing discrete components. Trim the leads as close as possible and be sure to orient diodes and capacitors correctly.
6.1.4 VERIFYING CORRECT GAME OPERATION: After locating and correcting the cause of a trouble, re-energize the game and perform a final check on correct game operation. Doing this will verify that your troubleshooting was correct. If the game operation is still not correct, go back and double-check your work. Make sure that any replaced components were installed correctly. If this was done properly, then start the troubleshooting steps over again. Keep in mind that there may be more than one trouble at
atime, and that correcting one trouble can sometimes
bring previously undetectable troubles to light. This verification is especially important when the original trouble had been intermittent, that is, was not happening all the time.
6.2 TEST EQUIPMENT
Electronic troubleshooting of a video game essentially consists of checking for the presence of various signals and of examining their condition. A
signal can be thought of as acting like a “messenger”
that carries instructions from one unit or circuit to another. Many different types of signals are produced in a video game, and for this reason several unusual and perhaps unfamiliar types of test instruments are used during troubleshooting. Each instrument has its own set of advantages and disadvantages for examining a given type of signal, and both the depth of the intended troubleshooting capability and budget will determine what instruments will be needed. Some instruments are basic and essential, no matter what size of service facility, while other optional instruments are desirable because they make troubleshooting easier and quicker.
6.2.1 BASIC TEST EQUIPMENT:
- The Video Probe, This is a simple but invaluable instrument having two leads—a test-clip lead and a test-probe lead. During troubleshooting of video signals the test-clip lead is left connected to the game side of the video coupling capacitor. On the Crash ’N Score game this point is the junction of resistors R23, R24, R25 and R33 on the PCB. When the test-probe lead is then connected to any video developmental signal, that signal will be coupled to the video signal going to the TV monitor and a video probe picture will appear on the TV screen. The shape and other characteristics of this picture will give information about the signal being probed. The video probe is suited for troubleshooting synchronization and image signals, but will not be useful for extremely fast signals (such as the clock) or for very slow analog or digital signals. ‘A video probe can be constructed in a few minutes from these common electrical components: a length of 20 AWG (American Wire Gauge) rubbercoated wire, a 4.7K-ohm, ¥4-watt carbon resistor, and two test leads. For the leads, use a single Mouser test clip (Mouser #131C301 or 302) attached to one end of the wire, and a test prod containing the resistor on the other.
To assemble the video probe, proceed as follows:
Remove the cap from the test clip and strip 3/16 inch off each end of the wire. Solder one end to the postin the test clip, thread the other end through the hole in the cap, and snap on the cap. Next unscrew the plastic body of the test prod from the point and trim both leads of the resistor to a 3/16-inch length. Solder one resistor lead to the inside of the point. Thread the other end of the wire through the hold in the body and solder it to the other resistor lead; screw the body back onto the point.
- The Logic Probe. This is a test instrument designed for fast verification of digital IC outputs. It is small, convenient to carry, easy to read, and relatively inexpensive. The logic probe derives its power from the system under test; it has two power leads,
one for connection to ground and the other to +5 volts
DC. When the logic probe’s tip is held against a digital signal point, three colored lamps in the tip will indicate the signal's condition or state, as follows
@ The red lamp lit indicates a high or logical level
1 (for TTL components, this is +2.4 to +5 volts) © The white lamp lit indicates a low or logic level 0 (for TTL components, this is 0 to +0.8 volt) @ The blue lamp lit indicates that the signal is changing states © No lamps lit indicate the grey region between 0 and 1 (for TTL this is between +0.8 and +2.4 volts) A circuit shorted to ground will illuminate the white lamp and an open circuit will illuminate the red lamp. The logic probe is readily available from electronic supply sources; a commercial model found satisfactory is the Kurz-Kasch model LP 520.
- The Logic Pulser. This test instruments similar in size and shape to the logic probe, and it also derives its power from the system under test. When the logic pulser’s tip is held against a digital signal point, the source and sink capabilities of the pulser override any IC output and the point is driven to the opposite logic level. If the point that the logic pulser is held against is low, pressing the switch on the side of the pulser will introduce a high pulse. Conversely, pulsing a high line will pull that line low momentarily. During troubleshooting the logic pulser allows stimulation of in-circuit ICs with a shaped digital pulse. For example, a certain feature of the game may not be working and you suspect that a circuit is not receiving the necessary signal. Use the pulser to imitate that signal and if the circuit begins working, you have proved that the signal was in fact missing and you can begin tracking it down. This technique is very similar to jumping coils in electromechanical games such as pinball machines. In addition to the regular “pulse” button, there is another switch mounted on the logic pulser. When this switch is set in the “rep” mode, the instrument pulses the digital signal point at a 5-Hz rate or 5 times per second. This extremely low rate is slow enough to allow watching events initiated by the pulser. Counter outputs, for example, are more easily observed when the counter is pulsed or clocked at this rate. The logic pulser is also readily available from electronic supply sources; a commercial model found
satisfactory is the Kurz-Kasch model HL 583.
- Oscilloscope. The most versatile test instrument, and also the most expensive, is the oscilloscope. The high-speed TTL integrated circuits used in video games produce fast-rise-time signals. The oscilloscope should have a 50-MHz bandwidth, dual trace and dual time base capability. These latter features allow examination of both input and output signals simultaneously, so that precise timing relationships can be checked. The oscilloscope should also have provision for internal or external sync, Of the newer, solid-state oscilloscopes, a sati factory model is the Tektronix 465.
- VOM or Volt-Ohmmeter. This common measuring instrument is extremely useful in video game troubleshooting. It can be used to check line voltage, transformer secondary windings, continuity, resistance, power supply voltages, and to some extent used for measurements in the analog circuitry. One commercial model found satisfactory is the Simpson 260.
6.2.2 OPTIONAL TEST EQUIPMEN
- The Logic Comparator. This test instrument’s main benefit is that it can be used to check the functioning of an integrated circuit device while the
device is still in place on the printed circuit board. The
logic comparator performs the check by comparing the suspect ICs functioning with that of an identicaltype reference IC mounted in the instrument itself. Suppose that the functioning of a type-74193 device on the PCB is suspected to be defective. First insert a program card with a known-to-be-good 74193 into the logic comparator, and then clip the comparator
test leads onto the leads of the suspect device. If there
are any logic state differences between the reference IC and the suspect IC under test, then an LED on the logic comparator will light up to indicate which output is not functioning correctly. Once a defective IC has been located, it should be replaced. Logic comparators are readily available from electronic supply sources.
- Atari Universal Test Fixture. In situations where a large number of video games are being serviced, investment in the Universal Test Fixture will be justified. This item of test equipment forms a test station for troubleshooting printed circuit boards after they have been removed from the game cabinet. The Universal Test Fixture has a full set of controls for operating the game and also has its own TV monitor. The game’s PCB is pluged into an edge connector mounted on the side of the Fixture; with this arrangement the PCB is positioned in a convenient way for connecting probes and other test instruments. A program card inserted into a receptacle in the top of Fixture takes the place of the game's interconnect wires. The program card thus sets up the Fixture for each particular game; the game’s name is clearly printed on the program card itself With the Universal Test Fixture the method of troubleshooting via substitution of known-to-begood parts is made fast and convenient. For example, suppose that the TV picture in a game is completely broken up and you want to determine whether the
game or monitor is causing the problem. Remove the
PCB and plug it into the Fixture’s edge connector, and also insert the correct program card for that game. If the picture on the Fixture’s monitor is correct, then you know that the problem lies in the game’s monitor.
6.3 SPECIFIC TROUBLESHOOTING INFORMATION
The following subparagraphs give additional troubleshooting information about certain areas of the Crash 'N Score game.
6.3.1 ANTENNA STATIC MODIFICATION: This subparagraph gives a procedure for modifying the antenna, a wire connecting via PCB edge-connector pin 18 to the base of transistor Q7. Any signal on the antenna that will bring Q7 into conduction causes the “Q” Latch (formed by transistors Q8 and Q9) to be reset The operation of this circuit is described in detail in subparagraph 3.4.6 of this manual The purpose of the static modification feature is to prevent players from bringing the game into the play mode without having deposited coins into the game. Provided that the antenna wire has been adjusted to optimum length, this feature can make it impossible for a player to obtain bonus credits by inducing a static charge in the coin entrance plate or any other metal part of the game. The antenna wire is approximately one foot long, with one end intentionally left not connected. When a static discharge occurs, an electric current is induced in this wire and an impulse is transmitted to the Q latch circuit. This impulse resets the latch, turning off game credit and changing the game overto the attract mode. To test the static modification feature, touch the end of the antenna wire with your finger: the body usually has enough capacitance to trigger the circuitry. Sensitivity of the static modification feature can be adjusted by changing the length of the antenna wire. Lengthening the wire increases sensitivity, so that a lesser charge will turn off game credit. Cutting the wire shorter decreases sensitivity, so that a larger charge is required for triggering the circuit. If there are problems with static charges accidentally shutting off the game credit, try cutting the wire shorter in increments of % inch at a time. Be aware, however, that if the antenna wire is cut too short, players may be able to obtain free game cred (bonus games) by inducing a static charge in the game.
6.3.2 TV MONITOR: The TV monitor is a selfcontained unit housed in its own chassis. A trouble’s cause may be narrowed down to the monitor—either by the substitution method using a known-to-begood monitor, or by verifying presence of AC power to the monitor power supply and presence of the correct composite video signal. The entire monitor can then be removed from the game cabinet. Doing this facilitates troubleshooting steps, because all monitor components will then be accessible. A schematic diagram of the monitor circuitry is included in Section VI of this manual. After disconnecting and removing the monitor from the game, standard TV troubleshooting techniques are adequate for locating causes of trouble. Additional servicing information is available from the monitor manufacturer (Motorola).
6.3.3 COIN MECHANISM: If a player inserts a coin
and the game does not respond, first check the coin mechanism. If pressing the coin rejector button forces the rejector mechanism to return the coin, then examine the coin to make sure that it is genuine. If it is, then use a set of your own test coins (which should include both very new and very old worn coins) to determine whether or not the player’s coin is undersize or underweight. If your test coins are also returned, this indicates that servicing of the coin acceptor portion of the coin mechanism is called for. Generally the cause of this particular problem is an improperly adjusted magnet gate. Inside the coin mechanism a magnet is used to test the metallic composition of the coin. Highly magnetic coins, such as those made of steel or iron, will be retained by the magnet and can be returned by actuating the wiper operating lever. Coins having comparatively high magnetic properties will be slowed down by the magnet, and will drop off the end of the rail short of the “accept” entrance and be returned. Coins having little or no magnetic properties, such as brass or zinc coins, will pass through the magnetic field so fast that they will overshoot the accept entrance and be returned, A magnetic gate adjusted with too large a gap may pass both genuine and counterfeit coins. An adjustment with too small a gap can lead to rejection of some or even all coins. Over a period of time, the screw that adjusts the magnet gate has a tendency to work loose, resulting in a gradual narrowing of the gate. At first, only the thickest (newest) coins are rejected. As time passes, more and more coins are rejected until finally player complaints lead to the calling of the game repairman. If pressing the coin rejector button does not cause the coin to be returned, and if the game still does not respond, then check the coin mechanism to see if the coin is jammed inside. If you are certain that the coin is genuine, and that the coin passes through the coin mechanism and into the cash box, then the lack of game response is probably due to some kind of electrical trouble. Check for signals at the electrical contacts of the coin mechanism before moving on to the harness and other parts of the circuitry.
Vi.
Schematics, Drawings and Parts Lists
Number
004172 A004172
004174 004175
A004175 003094-xxx
A003094-xxx 000598-03 A000598-xx 000607
4000607
004218 004215 004215
004256 004256
A004256 Title
Parts List, Top Assembly Top Assembly
Parts List, Foot Pedal Assembly Parts List, Control Panel Assembly Control Panel Assembly Parts List, Double Lite Switch Assembly Double Lite Switch Assembly Parts List, Steering Wheel Assembly Steering Wheel Assembly Parts List, Steering Printed Circuit Board Steering Printed Circuit Board
Harness Schematic Parts List, Electronics Tray Assembly Electronics Tray Assembly
Printed Circuit Board Schematic Parts List, Printed Circuit Board Assembly Printed Circuit Board Assembly
ARCADE CRASH _'N' SCORE ASSEMBLY TIT! TOP ASSEMBLY 004172 NM PARTS LIST SPECIFICATION Page | of 2
| ATARI | Checked | Mech, Eng. | |
| Innovative | Proj. Eng | Elec. Eng | | Rev. |
leisure Lc Description Date Rev. | __Description Appr PROD RET 19/30/75
| Bt | p | 674 | 11075775 | |
| Rev per ECN | 170 | [0714775] |
a
+
| tem | Part Number | Qty. | DESCRIPTION, |
| 1 | 004155 | 1 | Cabinet Assembly | |
| 2 | 004175 | 1 | control Panel Assembly | |
| 3 | 004215 | 1 | Electronics Tray Assembly | |
| 4 | 4004174 | 2 | Foot Pedal Assembly | |
| 5 | 004214 | 1 | Playfield Plex Screen, Clear | |
| 6 | 003920-02 | 2 | Plexiglass Retainers | |
| 7 | 004166 | 1 | Bottom Plex Retainer | |
| 8 | 004171 | 1 | aBs Bezel, Black | |
| 9 | 004216-xx | 1 | Instruction Plate, Number Card | |
| 10 | 000869 | 2 | Speaker Grill | |
| ul | 000531 | 2 | Control Panel Mntg Bracket | |
| 12 | 003637 | 1 | Coin Door Assembly | |
| 13 | 4004232 | 1 | Decal Location Diagram | |
| 14 | 48-002 | 2 | Speakers, 4" Motorola | |
| 15 | 92-007 | 1 | 23" .v. Monitor | |
| 16 | 71-2114 | 1 | Hudson Lock | |
| 7 | 72-6810 | 20 | Screws, Self Tapping, #8 x 5/8 Phil Pan Hd | |
| 1s | 75-931 | 2 | Wing Nuts, #10-24 | |
| ig | 75-5124N | 10 | Carriage Bolts, #10-24 x ls | |
| 20 | 75-010S | 20 | #10 Flat Washer |
| 21 | 75-040 | 22 | #10 Lock Washer | |
| 22 | 75-9118 | 20 | #10-24 Hex Nuts | |
| 23 | 82-8116B | 4 | Socket Hex, Cap Screws, #10-24 x 1" | |
| 24 | 82-404 | 2 | Bye Bolt, #4-20 x 3" | |
| 25 | 004212 | 1 | R.H. Side Panel S/Screen | |
| 26 | 004213 | 1 | L.H. Side Panel S/Screen | |
| 27 | 004217 | 1 | Main Harness | |
| 28 | 004218 | Ref | Wiring Diagram | |
| 29 | 004177 | 1 | Shipping carton | |
| 30 | TM-048 | 1 | Technical Manual | |
| 31 | 004211 | 1 | Plexiglas, Playfield, Smoked | |
| 32 | 75-9158 | 2 | #4-20, Hex Nuts | |
| 33 | 75-015s | 2 | #4 Flat Washers | |
| 34 | 75-045, | 2 | #% Lock Washers | |
| 35 | 75-5120B | lo | Carriage Bolts, #10-24 x 1% | |
| 36 | 73-77004 | 8 | Rivets, 3/16 x .68 | |
| 37 | 004355 | 1 Free Play Card | |
| 38 | 72-6620 | 6 | Screws, Self Tap, #6 x l'y Pan Hd Phil |
@) | aooa278 1 | Coin Mech Housing Harness
| 40 | 72-6616 | 1 | Screw, Self Tap, #6 x 1" Pan Hd Phil |
ASSEMBLY TITLE ARCADE CRASH 'N SCORE Top assEMBLY = P/L 004172 PARTS LIST SPECIFICATION
Part Number DESCRIPTION
004236 Fluorescent Light Mounting Assembly A004286-04 Final Assy - R.F. Shielding Enclosure
75-5132N Carriage Bolts, #10-24 x 2"
Oran >
- Bi) (sen ea) HG 7
(sea)
$5)GEA BLD) »
_PROD_ RELEASE REV_PER ECN 1674 9-395 REV.PER ECN 1701 1034!
Th
a ii) GEG is we = DAD Cer a0)
a NOTES! ZX STEM 31, FREE PLAY CARD TO BE INSTALLED BY OWNER BETWEEN SMOKED AND SIS PANEL.
a —— —CYXDDD (ta ean)
ssrmareere Sun A sma neaton
ARCADE CRASH ‘N’ SCORE a aoa =p score TE
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
T PEDAL WARNESS———=1" OFEN i 1. ONITOR ~ uGHT
TO CONTROL PANEL SEE SHEET 1 OFZ
ARCADE a SERS Stun FOOT PEDAL ASSEMBLY P/L004174 PARTS LIST SPECIFICATION Page 1_of 1 Drawn, ATARI Checked Mech. Eng. Innovative Proj. Eng. Elec. Eng ) REV.
Part Number DESCRIPTION 1 A003511 Single Foot Pedal Assembly
| 2 | 004164 | Ref | Foot Pedal Board |
| 3 | A004219-02 | 1 | Foot Pedal Harness |
| 4 | 002932 | 1 | Front Mntg Bracket |
| 5 | 002933 | 1 | Rear Mntg Bracket |
| 7 | 65-071C | 1 | Switch, Cherry |
| 8 | 002191 | 1 | Brkt, Switch |
| 9 | 72-1416S | 2 | Mach screw, 4-40 x 1" Pan Hd Phil. |
| 10 | 72-6810 | 3 | Self Tapping Sheet Metal Screw, #8 x 5/8 Lg |
| 11 | 72-914S | 2 | Hex Nut, #4 |
| 12 | 75-0108 | 4 | Flat Washer, #10 |
| 13 | 75-040 | 4 | Lock Washer, #10 |
| 14 | 75-911 | 4 | Hex Nut, #10-24 |
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
ARCADE CRASH 'N' SCORE A ATARI Innovative leisure ASSEMBLY TITLE CONTROL PANEL ASSEMBLY
PARTS LIST SPECIFICATION
Checked Proj. Eng. Mech. Eng. x) Elec. Eng
i i [Rev per Bon 7S O/T i a a pic | 0 é |p| 4 ee SOC RTS RNS
Part Number 7 DESCRIPTION 1 | 004167 Ref| control Panel - Bolt
| 2 | 004173 | 1 ABS Control Panel |
| 4 | B000598-03 | 2 Steering Wheel Assembly |
| 5 | 004233 | L Panel, Control Plate |
| 6 | 14004219-03 | 1 | control Panel Harness |
| 7 | 000567 | 2 Bow, Washer |
| 8 | 001856 | 1 | Bushing, Switch |
| 9 | 62-009 | 1 Switch, LED |
10 | 75+5124N 4 | carriage Bolts, #10-24 x 1s
| 11 | 75-010S | 4 Flat Washer, #10 |
| 12 | 75-040 | 4 Lock Washer, #10 |
2B | 75-9118 4 | Hex Nuts, #10-24
| 14 | 72-1124S | 12] Mach Screw, #10-24 x 14 Pan Hd Phil |
| 15 | 72-6812 | 3 | Screws, Self Tapping, Sheet Metal, #8 x 3/4 |
| 16 | A004304-07 | z Double Lite Switch Assy - One Player |
| 17 | A004304-08 | 1 Double Lite Switch Assy - Two Player |
| 18 | 004168 | Ref Control Panel - Backup |
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
aw whoo oH PROD. RELEASE _{329-75| REULPER_ECN IGT t-3.75 REUPER ECN 1700 10-133: REV. PER EON 1715 O75, i
A sa menos
- — Arart AKCADE. CRASH 'N’ SCORE TOP ASS'Y- CONTROL PANEL brea te Me ooar TS ATO) lp “Aooai7s [= | i eae ae
UNIVERSAL
Innovative leisure SWITCH, DOUBLE LITE ASSY
per Ferber Een t768 | qrIz68 ee [eta per For ase—| 30/75, rs | ec Tsee Fo ea re S| {+—
Part Number DESCRIPTION 003175 A003840
003178 003177 003176 003180 003173 72-14 S 65-021C 70-13328 72-1403S 72-1428 75-914S
70-S0X Plunger, Lens Assembly
Lock Ring Switch Bracket Contact Spring Actuator Mntg. Screw, Pan Hd, 4-40 x Length ##a/R
Cherry Switch, G-18 (
Lamp, #328 Chicago Min. Screws, Pan Hd, 4-40 x 3/16" Lg Screws, Pan Head, 4-40 x 3/4" Long Hex Nut. 4-40
Lens Filter *If "0" is not indicated in either column, 3 Contacts (003176), 3 Lamps (70-13328), and 3 additional Screws (75-1403S) will A003094-XXKX pe required. If "0" is indicated in one column and a numeral in the other, 2 Contacts, 2 Lamps, and 2 additional Screws will be required.
[ | MS, BREW 7 * LENO +L LENG FILTER 2 LENS FILTER -0 [%@ | |-O[ No UsHT LEED ||-O] No UGHT USED =1 [7/2 |[-1 [No Fiver USED es NO FIVER USED we
-2 |5/e | [72] Rep -2| Rep -3 | 2/4 ORANGE, ORANGE -4 |7/e YELLOW YELOW 1 GREEN GREEN
LENS FILTER AS REQ'D we CMe tas AS REQ’'D. Leck eine 003178 /—sousines CO375 “== PLUNGER, LENS ASS'Y ACO 3840 —— SPRING COsLBO 003103 ——~ SeiycH BeackeyT
AcruaToR —~_ 002173 ~ ropes, sceew a oS a. = % _comTAcr >.
OOBLTG, AS READ.
THIS DRAWING REPLACED BY
AC04304 AND 1S TO BE
USED FOR REFERENCE ONLY
~ COBTT sented, cHEee aig | SCREW, MACH RDAD PH. 4-40 x "LONG
- 4 TER 1F ‘O'S NOT INDICATED IN ETHER, [— BCONTACTS; (031%), 3 LANDS (O13320) AND 3 ADDITIONAL SCREWS (75714035) A003094-XXX WiLL Be. REQUIRED IPS SiINimrcaTe
NONE COLUMN AND A NUMERAL IN,
THE CTHER, 2CONTACTS, 2 LAMPS, AND
2 ADDINONAL SCREWS WILL BE.
REQUIRED. i #1 LENS FILTER |] ® 2 LENS FILTER POT NG UGHT USED |FOT Ne UicAT USED =1 |NO FILTER USED ||-L [No FurTer UseD =2 | Rep [-2[ Rep
ARCADE CRASH 'N' SCORE ASSEMBLY TI STEERING WHEEL ASSEMBLY A, ATARI Innovative leisure PARTS LIST SPECIFICATION
Drawn Checked Mech. Eng. Proj. Eng. Elec. Eng | Rev.
| Ttem | Part Number | Qty. | DESCRIPTION |
| 1 | 000598 | Ref |Steering Wheel Assy (3201-3803) | |
| 2 | 000599 | 1 |cover | |
| 3 | 000605 | 1 |Housing (3201-3545) | |
| 4 | 000606 | 1 |shaft (3201-3544) | |
| 6 | 72-7512 | 3 |Screw, Mach, Fil. Hd, Phil, #%-20 x 3/4" Lg. | |
| 7 | 000607 | 1 |Printed Circuit Assy | |
| 9 | 75-07002 | 2 |Washer, Fender, | |
| iu | 76-042020 | 1 |Bearing, Thompson (20L20-F) | |
| 12 | 76-041010 | 1 |Bearing, Thompson (10L10-F) | |
| 13 | 78-40102 | 1 |Steering Wheel, 10" | |
| 14 | 75-945N | 1 |Nut, #%-20, Nylon Lock | |
| 15 | 72-9580 | 1 |Screw, Mach, Truss Ha, Slotted, #%-20 x 5 Lg. | |
| 16 | 000616 | 1 | Hub Light | |
| 17 | 75-055 | 1 |Washer, %" Int. Tooth, Starlock | |
| 18 | 78-16002 | A/R |Silicone Grease, Compound | |
| 19 | 73-1208 | 2 |Mach Screw, .256 x % Pan Hd Phil |
ASSEMELY —] STEERING WHEEL, Dl asooses ax[s
ATARI
© RACETRAK STEERING PCB ASSY Dwe-P/L 000607
Drawn
Checked Mech, Eng. Proj. Eng.
Rev Description Apprv. Description
H Redesigned 5-6-74 J_| Rev per ECN 397 5/28/74 K Rev_ per ECN 457 6/3/74 L_ [Rev per ECN 601 7/15/74 M Rev_per ECN 1531
Part. No. Qty. Description
| 000614 | 1 | Printed Ci |
| 001092 | 1 | Light Moun| |
| 001151 | Ref | Schematic |
| 11750/10-5750 | 2 | Reslistor, |
| 11471/10- 5471 | 4 | Resjistar, |
| 11332/10-5332 | 2 | Resistor, |
34104 /27-101103 | 2 Capacitor,
| 70006/38-2N5777 | 2 | Transistor} |
70000/34-2N3643 | 2 Transistor}
| 71008 /38-ME7124 | 2 | Light Emit} |
| 80089 /79-58005 | 1 | Connector, |
| 72-1212s | L | Sctew, |
| 75-042 | L | Wagher} S; |
| 75-9128 | 1 | Nut, Hex, |
| 003749 | 1 | Retainer, |
ipcuit Board (E)
iagram omp., 75 ohm, % watt, 5% omp, 470 ohm, % watt, 5% omp, 3-3Kohm, % watt, 5% Ceramic, .Oluf |, 2N 5777 (Photo Darlington) 2N 3643 ting Diode, 1.R. ME 7124
10 pin, PC Mount, Amp #1-380991 sonra Pan Head Phil, #2-56 x 3/4 Lg. iL. it Lock #2 2-56 Led Light Mount
MODIF. 1 REFER TO SCHEMATIC OO!IS! RECESIGUED [REV. PER ECN 397
REV. PER ECN 457
REV Pez EX) Gol REV PER ECN 1531 MODIFICATIONS : FOR OOOGI4 BEV J P.C.BOABDS
1. JUMPER FROM PIN 2 TO PINIO OF THE 10 PIN CONNECTOR,
ON Ci@cUIT S\DE OF BOAeD.
2, JUMPER FROM PIN 1 OF THE 10 PIN CONNECTOR TO THE
PAD MARKED +SV (END OF 21) ON CIRCUIT SIDE OF BOARD,
MODIFICATIONS | FOR OOOGI4 REV K P.C.BOARDS, ), DUMPER FROM FIN 2 TO PIN IO OF THE IO PIN CONNEZ TOR,
ON CIRCUIT SIDE. OF BOARD.
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
DESCRIPTION INITIALS and DATE
PROD. REL. CHECK | wane
REV PER ECN Ww
Line GN z FILTER, 3
| w | Woo, | eK |
BK] = 5 s)- ~ Tt 2 Prayer St @ BarRieR SeELect Sw NC NO NO. NC tt V/BK 4R
| a | #2 | Hy | 193050702 |
'ye89 |STEERING STEERING |2e4y5e64q GNw
| ak | = | _ | = | _— | ar | 4 |
= 5) g 4 3
x v WIGN
[INTERPRET THIS DRAWING PER USASI YI48
HARNESS ATARI INCORPORATED 14600 Winchester Boulevard Los Gatos, California 95030
"ARCADE CRASH N SCORE
SCHEMATIC
Innovative leisure
Part Number DESCRIPTION
004176 001551 72-6608 000622 79-3201 46-201132 90-3001 68-001 000268 A004244 A002808-03 72-6812 A004217 A001920 A001921-01 A001921-02 A001921-03 A001921-04 A003100-04 000871 Tray, Electronics Transformer Screw, Sht. Metal, Pan Hd., Phil., #6 x 4 Lg. Cover, Transformer Fuse Holder Fuse, 1.25 Amp Filter, Power Line A.C. Power Interlock Switch Bracket, Switch Mtg. Power Cord Assembly, 8° Interlock Switch Jumper Screw, SM, Pan Hd., Phil., #8 x 3/4 Lg. Harness Harness, Voltage Selection Shorting Block, 95V Shorting Block, 110V Shorting Block, 220V H Shorting Block, 220V L Fuse Jumper Harness Label
MFIs | PROB REL
TEANSFORMER WIRES or SOURCE on [voor SELECT. WARN
ev cnewr | sce NOTE ak |your. SeLecr WARN. vesx | See Nore auiw MAIN HARK. ASSEMBLERS NOTE
COMBINE GN WIRE, FROM VOLT. SELECT., WITH
wit : WHT WIRE, FROWA MAIN HARNESS, AND V WIRE, w/pu FeOM volt SELECT. WITH BLK WIRE, FROM See MAIN HARNESS, USEING 7 IB7 FASTONS,
eney wir lone BNW BW on oun veurers
ARCADE CRASH N SCORE
ELECTRONICS TRAY A004215
vt
a anes
330 Lay a hs ED
x a“ esont Aa © 9 pr ‘S64 Sfoo)eé aso Sg
| a | 7 | ye, | “canara | agtt |
| cue | sen] | ons Pe | 3 oa) 8 |
eo oc me
| [s TRESE | anal | om |
rps san Bp
| vreser | i | pe! |
Tone
5 Aya a} sey 2 SRT
| vere | ele | fakes | v8 | t |
thre ae | Fela a2 a5e0 on pe aR a2 2b acn can 24) Lae earl os pet asc 31 om pp aay
| Fou 8 20 VER | ev Spee By | WHITE FLAG |
ond CF ‘al i= LOCATIONS 324 8 lu, conn 2207 Te
- FLAGS °
| Ke | B - | BARRIORS | \ |
| walle 2. | ae | emer Ban | |
| mt Moh | ARE | cae y + sucs |
Ye a nv aoa SicKs op) 134.93 _| $3
| 08) 2fio s& | a | ~ can TE y euicus |
oa 3
No ct a BARRIER, Seuect K. ea #4 "i. oz) eee
| TRANSFORMER | ~ | wan 22S |
: G a OO1DS) BARRIER VIDED me} a au ar seers | vets wnvac saveleces nese 82, 2 R104 R21 a] . or
- Z ALL DIODES ARE INDI4,
| Sum340 | ae | J ALL RESISTORS VALUES AX | |
| Bey aiae | By] oP? | co | NOTES! UMLESS OTHERWISE SPEC |
i ‘GND
DierwaL
PREPERBUC IO BELEASE PRODUCTION RELEASE. faev ree cou vee, 04 Re Pee HES BS
SCORE WINDOW Saat efoapt WHITE SCORE
iso (G5>® BACK SCORE
| 2 | Bg | 8 |
Pe ne
| "j | paper | os * |
ail Is* yf
| 22 | wee2 | [SE | I |
weed ey = fi
DRE WINDOW
Del al
| rina] | 3 | a | 2 |
ls is acs art BANE |
| geld + EK | 2 | ath |
hp sv TE fiat s sis sec
Sa
oe Roars ae 4,04 iy Aang Sales alit__air-z fei se Ha 1/2 9602| 9 a <3 tw __d WRITE FLAG
a3
soy
CAR RESET 1 #
car weset 2 ¢ SYNC
TARR Ip HRC ScoRE ‘BAC FLAG: ‘SUCKS,
WHITE a3, Fine Fl enna S ne
WAST BEF, DESIG.
oe as em RISO st
¥ IK ORME Law, 10%: Heo,
v BLACK FLAGS
MAK Fass
Rea aie
fg) vivo out
BACKGROUND,
EXTRA GATES EXTRA PINS
EEEEE MwN2, MIN2, MN
1200 seh Brat
SCHEMATIC CRASH N’SCORE BT" 04256 | —a
TSv Re 2 PLAYS/e599 IO K woes en
START#! PLAYER
VOR 2 CREDIT ‘2 s np>2 13
ATTRACT
a7 €i0
fo] Hiseses
START *2 PLAYER
coin, GAME TIMER
9, Fee
JE 2fpet attract teh) & # aF #0 r
tS
BONUS COIN COIN
TER START
\ a TCR START
ry
ORE CREDIT ato ey abner 2 cReDIT 470 f \06-1
z I 3 2 CREDIT LIGHT
eva
io camel “] FREE GAME SELECTOR ces P| 630 vac sw
pot y
P ED“ Bonus COIN B
END GAME + _— arrexce {fh a] w A fa é e z
| a | 2 | a | |
| t | 2 | i | |
| I | ir] | 7 | |
| ls | | | ba | i |
Bian ty a sonus con LOL Pieroni A
SCHEMATIC waren CRASH N’? SCORE Mee "564256 a oe rece
ATTRACT I AO eecen
HT lee TS Lelcr a ap ac, eee Bt 02 8 O08, prere
vrertt
aT.
speeosr speeo4 tt ee SPEED3I-3420 ‘SPEEO?T
‘cee “e Ee p22 cae ML SLICK [at L
- |_| ere rors e257 fo 854 ma Se) emer ets spate as bo srecosr 28 erupts TEBE
| ry | +8v | +Sv | ‘BG |
re cae weseran Boo? eon re oro mye RY FREQUENCY I eas OF ar 2F 1 280% ee sor
02 Ro3, me SiGe
epeen iT
nates
| speep 31-'Pde2—AAA | la le | ohh | |||
| ° | Bo | MY | ET | jeder Lie. | — |
| sreep 417 Besa 4 | low | Bes | vaste 3S | ||
| tc | ; | ae |
rast at it wave ee =
Sik t
exit ws -
ao
+50
Ice us.
arapet Ts
t LIL cone cLockt SAE ks 1 dre fe Cae WOW athe wl, HE ° phe Sie “lg 2 Ble 8 Wer 7
clock 1 ——+——24
eros. +20V UNRES, weo1 4001 *
fy
(003629 al o eT
2uaes3)[a2 ie ATTRACT. _
ne A FREE GAME TONE Sek Ri2a Scere Tone
CRE EB
SCHEMATIC CRASH N'score
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
| u | Is la [5 je |e | 3 lo [5 je Io |
Seb Pe Se 0 Pe FG Pe ‘ ees ME, eH ET gaic Tel ee nh 08 GC oD Mil i fa a8 ac GD Mi [ ana i" cont ce Gs crocum C4 ju efi a [zal it 30-3T a a oan nC le Holle rs 3 . Bre ome 3E 3 ss iz Dens Vie x bs . He c ee feral S} mee LSB! vee = Aer able refS} _L94ctor co
| fa anc ao wa | nee | j |
apatepay les croc p24
| = | TAR RESET | ri |
| | | a | Te. |
avpio MOTOR. VoUUME =
Re 13 tow Rs? RD Opt
TJavoio our
inte
(CRUNCH) REF
CAR It
“30 ror ate
=a Sola
| = CRASH IF | — | “DESON ENGINEER |
SonrACe FSH SCHEMATIC ee eee J meorome | CRASH NV SCORE a p= sd Pry a <= ib |""“coaese == ee
ASSEMBLY TITLE ASSEMBLY, P.C. BOARD
PARTS LIST SPECIFICATION A Drawn ATARI Checked Mech. Eng. Innovative Proj. Eng Elec. Eng REV. leisure c
Rev. | Description
| tem | Part Number | ty. | DESCRIPTION | |
| 1 | 004257 | 1 | Printed Circuit Board | |
| 2 | 37-7400 | 11 {1.C. 7400 | A3,B5,C9,E4,F9,H3,04,K5,L9,P3 |
Pg
| 3 | 37-7402 | 9 |I.c. 7402 | C8,E6,F1,F4,H2,L4,L8,N4,N6 |
| 4 | 37-7404 | 12 | 1.C. 7404 | Al ,A6,C3,C10,07,£10,J3,J6,J9, |
M7 ,N10,R3
| 5 | 37-7406 | 1 J 1.C. 7406 | L10 |
| 6 | 37-7408 | 3 [1.C. 7408 | F3,08,MN |
| 7 | 37-7410 | 5 |1.C. 7410 | B6 ,D3,F10,K6,P2 |
| 8 | 37-7414 | 1 1.C. 7414 | H10 |
| 9 | 37-7420 | 4 |1.C. 7420 | C4,£8,N3,N8 |
| 10 | 37-7430 | 1 [1.C. 7430 | Bl |
| W | 37-7432 | 1 1.C. 7432 | R4 |
| 12 | 37-7448 | 1 1.C. 7448 | Jl |
| 13 | 37-7474 | 14 | 1.C. 7474 | AS ,A7,A8,B3,DE1,H9,J5,07,K3 |
K4,M4,N1,R2,R9
| 14 | 37-7475 | 2 {1.C. 7475 | H7,R7 |
| 15 | 37-7485 | 3 {1.C. 7485 | B4,D9,M9 |
| 16 | 37-7486 | 3 | 1.C. 7486 | D4 M3 ,L3 |
| 7 | 37-7490 | 7 | 1.C. 7490 | B8,K8,L1,L2,M1 ,M2,P10 |
| 18 | 37-7492 | 2 |1.C. 7492 | BO,K9 |
| 19 | 37-7493 | 5 |1.C. 7493 | A4,D1,D8,E1,M8 |
| 20 | 37-74107 | 6 |1.C. 74107 | C7,F5,FH1,L7,P1,P5 |
| 21 | 37-74153 | 3 | I.C. 74153 | F2,K1,K2 |
| 22 | 37-74192 | 1 J 1.C. 74192 | E3 |
| 23 | 37-74193 | 7 {I.C. 74193 | E9,F8,H8,N9,P4,P8,R8 |
| 24 | 37-74279 | 2 |1.C. 74279 | MN2 ,N2 |
| 25 | 37-9312 | 4 |1.C. 9312 | H1,H5,02,R5 |
| 26 | 37-9316 | 13 | 1.C. 9316 | A2,B2,C2,C5,C6,05, D6,E5,L5,L6 |
M5 M6 NS
| 27 | 37-9602 | 2 |1.C. 9602 | H4,R |
| 28 | 37-555 | 6 |1.C. 555 | B7 ,D10,K7,M10,R10 |
| 29 | 37-LM323 | 1 | Reg LM323 + 5V | |
| 30 | 37-LM324 | 2 |1.C. LM324 OP AMP | C11,L11 |
| 31 | 37-LM340T-15 | i Reg LM340T-15 +15V | Qi3 |
or 7815
| 32 | 37-LM380 | 2 |1.C. LM380 Audio AMP B10,K10 |
rae
ASSEMBLY TITLE CRASH 'N SCORE P.C. BUARD ASSEMBLY P/L 04256 Rev ¢
45, Part Number
003186 003187 004248 004247
7939-42424 79-42116
31-MR501 31-Al4F 31-1N4001 31-1N914
33-2N3644 34-2N3643 34-2N3565 003629 35-MCR106
38-MV5013
21-500103 21-500104 24-160808 24-250105 24-250505 24-250106
24-250107 24-060257 24-250507 24-250478 27-250103
27-250104
28-101101
28-101391
10-5101 10-5151
10-5221
10-5331 10-5471
10-5102 PARTS LIST SPECIFICATION
DESCRIPTION
=--nn
Uyeyn FN
FHN-w CfHOFNNY HO WENNW Rom, RT8 Car Video F6,P6 P-Rom, RT8, Car Motion Code F7,P7 P-Rom, Crash 'N Score, Location Code D2 P-Rom, Crash 'N Score, Shape Code E2
24 pin I.C. Socket 16 pin I.C. Socket
Diode MR501 Power DI0,D11 Diode Al4F Power DI8,D19 Diode 1N4001 Power 027,028 Diode 1N914 03,D5-D9,D12,D194, 016,017 ,020-D26
Transistor PNP 2N3644 Q1,04,99 Transistor NPN 2N3643 Q7,Q8 Transistor NPN 2N3565 Q3,06 Selected NPN Noise Source 2N3643 2 SCR Transistor MCR106 Q10,Q11,Q12
Light Emitting Diode, Visible Red DI,D2,D4,D13,D14
Capacitor, Mylar, .Oluf, 50V C10,C49 Capacitor, Mylar, .luf, 50V C15,C52 Capacitor, Elect. 8000uf 16V c45 Capacitor, Elect. luf 25V €14,C016,C53,054 Capacitor, Elect. 5uf 25V C7,C18,C48,C59 Capacitor, Elect. l0uf 25V €5,C8,C9,C12,C2: C47,C56,C67, C68 Capacitor, Elect. 100uf 25V €4,C38,C39 Capacitor, Elect. 250uf 6V Cl Capacitor, Elect. 500uf 25V C25,C66 Capacitor, Elect. 4700uf 25V C57 Capacitor, Ceramic .Oluf 25V €3,C11,C19,C36, C37,C41,C42,C50 C60 ,C69 Capacitor, Ceramic .luf 25V €13,C€21,C22,C24 €26-C35,C43,C44 C51,C55,C62,C63 C65, C70 Capacitor, Mica 100pf 100V €2,C17,C20,C40, C58,C61,C64 Capacitor, Mica 390pf 100V C6,C46
Resistor, Carbon, 5%, 1/4W, 100 ohm R75,R77,k79
| Resistor, " | 7 | ‘ | 150 ohm R9,R10,R73,R74 |
Resistor, 220 ohm R14,R32,R33,R66 R72,R76
| Resistor, " | . | " | 330 ohm R78,R118,R119 | |
| Resistor, " | . | 470 ohm R24,R31,R65,R71 | ||
| Resistor, " | " | i: | 1K | R3,R7,R8,R25,R3G |
R69,R70,R95,R103,R104,R120,R121 ,R49,R54, R55 R64
ASSEMBLY TITLE CRASH 'N SCORE P.C. BOARD ASSEMBLY
10-5272 10-5152 10-5472
10-5103
10-5123 10-5153 10-5333 10-5563 10-5683 10-5393 10-5104
10-5224
10-5474
10-5105
10-5225 10-5475
17-54P0
19-311103 19-311254 19-311105
66-024P1T 69-001
72-1406C 75-016C 75-914C 75-054 75-056 75-916C
78-06004 78-16005 90-101
72-1610 10-5273 10-5333 UNyrV—wnn
= NN *
—N~
NYONNONND Resistor, Carbon, 5%, 1/4W, 2.7K
| Resistor, " | 7 | 7 | 1.5K |
| Resistor, " | " | a | 4.7K |
| Resistor, " | " | " | 10K |
| Resistor, " | e | s | 12K |
| Resistor, " | ‘ | : | 15K |
| Resistor, " | NM | " | 33K |
| Resistor, " | ia | 2 | 56K |
| Resistor, “ | = | : | 68K |
| Resistor, © | 7 | 2 | 39K |
| Resistor, " | : | " | 100K |
| Resistor, " | il | " | 220K |
| Resistor, " | " | " | 470K |
| Resistor, " | ‘ | : | 1 Meg |
| Resistor, " | 2 | " | 2.2M |
| Resistor, “ | " | " | 4.7M |
Resistor, WW, 5%, 10W, 4 ohm
Trim Pot, 10K ohm Trim Pot, 250K ohm Trim Pot, IM ohm
Dip Switch, 4SPST Switch, DPDT
Washer, Flat #6, CRES Nut, Hex 4-40, CRES Lockwasher, Int Star #4 Lockwasher, Int Star #6 Nut, Mach, Hex, 6-32, CRES
Heat Sink, Wakefield #680-.75A Silpad, Wafer, Insulator, To-3 Crystal 14.31818
Resistor, Carbon, 5%, 1/4 W, 27K P/L 004256
Screw, Mach, Pan Hd, Phil 4-40 x 3/8 , CRES
Screw, Mach, Pan Hd, Phil, 6-32 x 5/8", CRES
Resistor, Carbon, 5%, 1/4 W, 330K Rev c
R126-R129 R23 R15-R22 ,R80-R87
R2,R12,R37 R46, R56 ,R58 R59, R60, R93,R98,R105, R110,R111,R112, R122 R62,R114 R38, R99 R1,R48,R107 R123 R34,R96 R50,R108 R5,R11,R39,R41, R47,R51,R52,R53, R61,R100,R102, R106,R113,R115, R116,R117,R124
R30, R35 ,R92,R97
R29, R91,R101
R26, R63, R88, R125
R28, R90 R27,R89
R6
R57 R109 R13,R94 R4
S2 SI
YI
R67 , R68 R130
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Nest mee [FR © REDRAWN PER ECN
Ea) €
NOYES? UNLESS OTHERWISE SPECIFIED USE THIS Assy DWE WITH 004757 REVC PC. BoReDS,
ZALL DIODES ABE INDIA.
MODIFICATIONS TO 004287 REV C PC. BCAROS \ BOB AO. CAPACITOR FROM A4 BIN 14 TO +5y BUSS. (cI)
- ADB A JUMPER FROM PIN OF cil TO PAS OF LIL. BLADE A Inf /25V CAPACITOR (CTI), POSITIVE SIDE TO PIN IB OF HIO AND NEGATIVE SIDE TO GND TRACE, ABO & 1uf/25V CAPACITOR (C12)y POSITIVE SIDE TO PIN TOF HIO AUD NEGATIVE SIDE TO GND TRACE.
ini Wan Brat (eas rt ATARE
Tone anea ™ ASSEMBLY,
CRASH N? SCORE = Lp I" Aooeese Te | P/LCoazse
JONUOW LOLWX/LOSWX 201020WN ‘ONeUIDYDS