CATHODE RAY TOMES

Soul Edge V2 Kit

Soul Edge Ver. II (Asia, SO4/VER.C) (Namco, 1996) · Kit Manual · 28 pages · 21 sections · original scan

Page 1

namcoO’America, Inc.

C

KIT

Installation Manual

Page 2

Important

Read PRECAUTIONS and INSTALLATION Sections before operating game

FCC Notice

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operating in a commercial environment. This equipment uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Copyright 1996 NAMCO AMERICA INC. - Alll rights reserved No part of this publication may be reproduced by any mechanical photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from NAMCO AMERICA INC.

Page 3

SOUL EDGE™ Kit Installation Manual —— eS OO

TABLE OF CONTENTS

1.0 SPECIFICATIONS. 1.1 GAME CONVERSION OVERVIEW.

2.0 INTRODUCTION AND GAME PLAY

2.1 MAXIMIZING EARNINGS.

3.0 INSTALLATION.....

3.1 PRECAUTIONS.

3.2 CABINET PREPARATION

3.3.GAME INSTALLATION

3.4 CONTROL PANEL

3.5 CABINET GRAPHICS

4.0 SET-UP AND TEST..

4.1 TEST MODE.. rad 4.2 TEST MODE PROCEDURE .......ccesssssssessssseseeeeeensenesenenererenenecsterscaeeseseceerensnesens 8

4.3 TEST MENU

4.3.1 Switch Test Screen

4.3.2 Coin Options 4.3.3 Game Options 4.3.4 A.D.S. Screens.

5.0 SOUND VOLUME ADJUSTMENTS.

6.0 MONITOR ADJUSTMENTS ........cccccccceceseseseseeresseseserenesesesensasecareasessnerecesssscesesenssesenees

7.0 PCB CONNECTOR TABLEG............

7.1 JAMMA EDGE CONNECTOR . 7.2 EXTENDED EDGE CONNECTOR ........ cs cssssssseseseeseeeseeensesnenenenseneatataessseseeeennenens 16 APPENDIX A: ILLUSTRATIONS and PARTS LIST

APPENDIX B: WIRING DIAGRAM

Page 4

SOUL EDGE™ Kit Installation Manual

1.0 SPECIFICATIONS

Conversion Game

Power Supply: 150 Watt computer-grade, providing +5 VDC +/- 5%, 5 Amp Minimum +12 VDC +/- 5%, 2 Amp Mimimum

Harness: 56 pin JAMMA-Type, Key installed at pins H & 7.

Monitor: Horizontally mounted color monitor, accepting RGB video inputs from kit PCB.

Kit Specificati

Control panel: 2-Player configuration.

  • 8-Way Joystick, black: (1P, 2P, 1 each)
  • Push-button switch, white: (1P, 2P, 2 each)
  • Push-button switch, yellow: (1P, 2P, 4 each)

Marquee and Graphics Set

Kit Game PCB

  • | Namco System 11 SOUL EDGE PCB, w/ Foil Shield

56-Pin Connector Harness 48 Pin Connector Harness

  • DDK 225D-10024C2-2312 only

! IMPORTANT NOTE ! The 48-pin connector supplied with the SOUL EDGE kit has a small pitch or distance between connection pads. DO NOT SUBSTITUTE OTHER 48 PIN CONNECTORS.

Note: Specifications subject to change without prior notice. Modification and/or alteration of the SOUL EDGE game kit with kits or parts not supplied by NAMCO may void the warranty.

REMOVAL OF SERIAL NUMBERS AND/OR BAR-CODES FROM PRODUCT OR COMPONENTS WILL VOID THE WARRANTY

Page 5

. namco° Kit Installation Manual SOUL EDGE™ ——————————— Oe

1.1. GAME CONVERSION OVERVIEW The SOUL EDGE kit consists of the SOUL EDGE PCB set, a standard JAMMA (56 pin) wire harness, an extended JAMMA (48 pin) wire harness for stereo and extra controls, a set of player controls and SOUL EDGE graphics. This kit can be installed in an industry standard 25 or 27 inch color monitor kit cabinet. Optimum results are achieved by installing SOUL EDGE in a cabinet with stereo speakers and a large, 4 player size control panel.

Page 6

SOUL EDGE™ Kit Installation Manual

Ver. Il

2.0 INTRODUCTION AND GAME PLAY SOUL EDGE VER. II is an update to the original game. The basic core game play remains the same. Look for the updated logo (two crossed swords w/’Ver. II”) in the attract screen to guarantee which version you have. Additions and modifications make SOUL EDGE VER. Il an even better game. SOUL EDGE VER. II is a new 2-player, 3-D polygon, weapons-based fighting game. Powered by Namco’s System 11 hardware, players are treated to brilliant graphics featuring the most fluid graphics ever seen! New features*3-D Attack”, 3-D Defense”, “Locked Weapons’, ‘Guard Impact” and ‘Critical Edge” will break new ground in fighting games. Players select from eight armed warriors from around the globe, each wielding their weapon of choice in pursuit of the ultimate weapon.

Increased Number of Characters The original game featured a selection of eight characters. In Version Il, Cervantes De Leon and Hwang Sung Kyung become selectable. All characters now have two different clothing colors. Select their original clothing colors by pressing button A. Select their new clothing colors with button B or K. If the G button is held down while pressing the A, B or K buttons, an optional clothing set can be selected. Four Buttons Provide a Variety of Functions: # = G - Guard: Used in combination with the joystick, players can block a high, medium or low attack. # H - Horizontal Attack: Used in combination with the joystick, characters perform a high, medium or low horizontal weapon attack. # = V - Vertical Attack: Used in combination with the joystick, characters perform a high, medium or low vertical weapon attack. # K - Kick: Used in combination with the joystick, characters can kick high, medium or low.

Page 7

Kit Installation Manual SOUL EDGE™ Eee

3-D Attack and 3-D Defense: Once predicting an opponent attack, players can perform an evade move by side stepping left or right. This presents the defender with an attacking opportunity via a counter attack.

Guard Impact: By using the joystick and pressing the “guard” button precisely at the point of impact, players can momentarily knock loose their opponent's weapon, leaving him/her defenseless and vulnerable to an attack. Guard Impact works for all weapon attacks (upper, middle, lower), except jumping attacks. This is a modification of the original Guard Impact.

Attacking from a “Locked Sword Position”: When two players perform the same attack on each other at the same time, the characters will lock their weapons for a brief moment. During this time, players must choose a followup horizontal, vertical or kick attack. When the weapons unlock, characters will each perform their commanded move. Critical Edge: This move is a 3-button command that automatically executes a combination move. In exchange, the player sacrifices a loss of weapon strength. “Critical Edge” is composed of a first and second half combo. Once the combo begins, players must repeat the command to execute the second half combo. If the attack is “guarded” or avoided, the combo ends there. Whether the first hit lands or not, the same loss to the attacker's weapon gauge is registered. If a player's weapon gauge becomes emptied, his or her character will lose it's weapon. The player must fight hand to hand for the remainder of the round. “Critical Edge” enhancements in Ver. II: e The subtracted value on the Weapon Gauge when using Critical Edge has been reduced. e Even after inputting Critical Edge, players may cancel the command by pressing the Guard button. ¢ Critical Edge can now be performed when back dashing. Critical Edge can now be performed on all opponents while they are in the air.

Floating Combos: This is a new feature added to Ver. II. All characters may now make“upswing attacks” on opponents who are in the air. Use the joystick in three positions (high, medium, low) and the B button for these attacks.

Page 8

SOUL EDGE™ Kit Installation Manual

Unblockable Attacks: All characters now have an unblockable attack in Ver. Il. There was an inequity in the original version as some had an unblockable and some did not. This move can be cancelled by pressing the Guard button.

Time Attack Mode: This is new to Ver. Il. Players can test their skill against the computer. In the title screen, press the start button while holding down buttons A + B + K to enter“Time Attack." Players will fight opponents in the same order every time. When the player reaches the end, several game play statistics will appear to rate each player's skill.

Buy-in’s are permitted even during “Time Attack”. The challenged player must win the match in order to resume “Time Attack." If defeated, the player loses his/her place in the “Time Attack” and must restart this mode from the beginning.

Throws: Throws in Ver. Il are now easier to perform.

2.1. MAXIMIZING EARNINGS To achieve optimum earnings it is recommended that you set the game to Namco’s USA RECOMMENDED FACTORY SETTINGS. We believe that these settings are the most suitable for a wide variety of locations. These settings are not necessarily the same as the GREEN default settings in both the “Coin Options” and “Game Options” screens. However, as all locations are not alike, they are easily adjustable through the TEST MODE.

3.0 INSTALLATION

Note: Shipping damage may void the warranty. In case of shipping damage, contact your distributor and the transportation carrier immediately.

Before beginning the installation, verify that the kit contents match the enclosed kit parts list.

3.1. PRECAUTIONS

  • Turn power to the cabinet off when installing any electrical or electronic device.
  • The SOUL EDGE PCB is a state of the art custom polygon graphics system that is very sensitive to electro static discharge (ESD). Be sure to use appropiate ESD reduction handling procedures such as use of ground straps. Handle the PCB using the anti-static material provided.
Page 9

Kit Installation Manual SOUL EDGE™ SS

  • The SOUL EDGE PCB can be damaged by even the small internal voltage of a multimeter or similar device. Never test the PCB for conductivity with such devices.
  • In the event of a PCB failure please contact your distributor for factory repairs.
  • Wrap return PCBs with a suitable anti-static foam or bubble wrap and label the return carton with the serial number and RMA number.
  • Dust or foreign matter may cause PCB failure. Dust can be removed using canned compressed air available at electronics supply stores. Turn the power off before cleaning the PCB.

3.2. CABINET PREPARATION Remove the following from the existing game or standard cabinet:

  • Game PCB
  • Control Panel
  • Marquee
  • Decals
  • Clean and fill all blemishes and dents and paint the exterior of the cabiner as needed.

3.3. GAME INSTALLATION

  • Mount the game PCB to the side of the game cabinet and enclose in the FCC EMI Shield Box provided. Install the ferrite bead and clamp provided with the kit, locating it close to the shield box.
  • Connect the JAMMA and the 48 pin connector to the game PCB, and wire in accordance with the connector tables and system wiring diagram found in the back of the manual.
  • Connect the monitor.
  • Connect the coin door and the coin meter to the wire harness.
  • Connect the test/service panel.
  • Connect the speakers to the wire harness.
Page 10

hamco° SOUL EDGE™ Kit Installation Manual ooo EEEEeEEEEESESESSSSSSSSESESSSSSoSS

3.4

1.

3.5 CONTROL PANEL

Locate the joystick and push-button holes as available in a standard cabinet control panel, or use the layout drawing provided in this installation guide.

The hole sizes and positions are dimensioned in the provided template drawing. Be sure to check the clearance for the push buttons and joysticks under the control panel before punching the holes.

To fabricate a metal control panel, the easiest method is to drill a 1/4 inch pilot hole and then use an appropriate size metal hole style punch and wrench to punch the holes by hand.

Install the SOUL EDGE control panel overlay provided in the kit. Using the control panel cutouts as a guide trim the overlay to fit. Apply the G, A, B, K, Player 41 and Player 2 labels.

Install and connect the push button switches provided in the kit.

Install the contro! panel on the cabinet and connect the control panel wire harness to the game wire harness.

Use the enclosed SOUL EDGE dedicated game wiring diagram as aguide to verify system connections prior to turning on power.

CABINET GRAPHICS

Install the cabinet side graphics provided. Float the graphics on by applying a spray of general purpose cleaner to the side wall. Smooth out the bubbles and liquid with a paint squeegee. Wipe the side decals dry with a soft cloth.

Install the marquee styrene provided in the kit in place of the existing marquee.

Install the game play and game moves instruction cards provided with the kit.

If needed, trim the graphics to fit the particular cabinet.

Page 11

Kit Installation Manual SOUL EDGE™

4.0 SET-UP AND TEST 41 TEST MODE TEST mode allows the operator to test the game controls, set various game options, set coin options and test and adjust the video monitor.

Important Note;

USA Recommended Factory Settings are not the same as the Japanese factory defaults (in green). Namco’s USA Recommended Factory Settings have been found to be the most suitable settings for most USA locations. However, these settings are operator adjustable and can be modified to best suit your location.

4.2 TEST MODE PROCEDURE

To enter TEST Mode, open the coin door and set the TEST switch to the ON Position.

Alt. Method: Flip SW2 No. 1 on the System PCB to the ON position. SW2 No. 2 must remain OFF at all times.

To adjust the setup options, follow these steps in sequence:

A.To SelectUse Joystick
B.To Call Up ScreenUse Left “A” Button
Cc.To ExitUse Left “B” Button

4.3 TEST MENU

TEST MENU

SWITCH TEST Switch test screen SOUND TEST Sound test screen COIN OPTIONS Coin options screen (Setting of game fees) GAME OPTIONS. Game Options (Setting of game difficulty) UARTS TEST Not used POLYGON TEST Not used ADS Screen displays tabulated operating data COLOR TEST Color test screen (for monitor adustment) CONVERGENCE TEST (i) Cross hatch pattern (for monitor adustment) RS-232C TEST Not used

TEST MENU SCREEN

Page 12

SOUL EDGE™

4.3.1 Switch Test Screen

4P: 0000 2P: 000 +++ +++ +xt xt +++ +++

3P: 0000 2P: [0] 000 SERVICE SW: + ANALOG 0: ? TEST SW: x ANALOG 1: ? DIP 1: + ANALOG 2: ? DIP2: + ANALOG 3: ? COIN1: + ANALOG 4: ? COIN2: + ANALOG 5: ? COIN3: N/A ANALOG 6: ? COIN 4: N/A ANALOG7: ? PADDLE 0: ? PADDLE 1: ?

PUSH B - BUTTON TO EXIT

#* 1B causes screen to exit to Main Menu Kit Installation Manual

"8" when P2 is pressed "4" when A is pressed “2" when B is pressed "4" when K is pressed

Joystick Switch Status

"4" when G is pressed

Page 13

Kit Installation Manual SOUL EDGE™ eee OOOO

4.3.2 Coin Options

COIN OPTIONS [DEFAULTS IN GREEN] ALL DEFAULTS SHOWN

(A) GAME COST: 2COINS 1 CREDIT DISCOUNT TO CONTINUE: B) NO (8) COIN 1 MECH VALUE: 4 COIN COUNTS AS 1 COIN

COIN 2 MECH VALUE:

  • 1 COIN COUNTS AS 4 COIN

COIN 3 MECH VALUE: 4 COIN COUNTS AS 1 COIN (c)

(D)

COIN 4 MECH VALUE: 1 COIN COUNTS AS 1 COIN

BONUS FOR QUANTITY BUY-IN: (e) NONE

CREDIT MODE: COMMON (F)

COIN COUNTER: TYPE A: 1 COUNTER

FREE PLAY: NO (s)

(H)

COIN OPTION SCREEN

(A)Game Cost1-9 Coins = 1 Credit
(B)Discount to ContinueYes/No
(C)Coin 1 Mech Value4 Coin = 1-9 Credits
(D)Coin 2 Mech Value1 Coin = 1-9 Credits
(E)Bonus for Quantity Buy-InNone/1-9 Coins give 1-3 Coins
(F)Credit ModeCommon/Each
(G)Coin CounterType A: 1 Counter/Type B: 2 Counters
(H)Free PlayYes/No
Page 14

hamco° SOUL EDGE™ Kit Installation Manual —ooEEEEEEEeeeEEEEEEEEEoEooEEEEEeeeeee

4.3.3 Game Options

GAME OPTIONS

DIFFICULTY LEVEL:

STAGE WIDTH:

FIGHT COUNT (1P GAME): FIGHT COUNT (VS GAME): 2 LIFE BAR (1P GAME): 400 LIFE BAR (VS GAME):

ROUND TIME: CHARACTER CHANGE AT CONTINUE:

CHARACTER CHANGE AT VS GAME: (A)

(8)

(c)

(D)

(E) (F)

(s) (H)

0)

W)

(kK) NEW CHARACTER:

MUSIC IN ATTRACT: MITSURUGI

YES

SPEAKER OUT: STEREO (L) EVENT MODE: OFF (m)

PRESS B-BUTTON TO EXIT

GAME OPTION SCREEN

(A)Difficulty LevelEasy, Medium, Hard, Extra Hard, Ultra Hard
(B)Stage Width15, 17, 18, 20m
(C)Flight Count (1P Game)4 thru 5
(D)Flight Count (VS Game)41 thru 5
(E)Life Bar (1P Game)90, 100, 110, 120, 130
(F)Life Bar (VS Game)90, 100, 110, 120, 130
(G)Round Time30, 35, 40, 45, 50 sec
(H)Character Change at ContinueYes/No
(!)Character Change at VS GameYes/No
(J)New CharacterMitsurugi
(K)Music in AttractYes/No
(L)Speaker OutStereo/Mono
(M)Event ModeOfffOn
Page 15

namco°: Kit Installation Manual SOUL EDGE™

4.3.4 A.D.S. Screens

A.D.S. MODE ON TIME: OH49M47S

COIN1 TOTAL 0 COIN 2 TOTAL 0 SERVICE TOTAL

TOTAL TIME COUNT AVERAGE

1P PLAYOHOOMOOS1OHOOMO0S
1P PLAYOHOOMO0S0OHOOMOOS

4PPLAY — OHOOMOOS OHOOMO0S

ALL PLAYOHOOMO0SOHOOMOOS

ON TIME — OHOOMO0S PLAY RATIO 3.8%

AP PLAY RATIO100%FREE PLAY

VSPLAYRATIO 0% 0

CLEAR: PRESS P1 LEFT UP & P1 START

NEXT: PRESS P14 A-BUTTON

EXIT: PRESS P41 B-BUTTON

A.D.S. Screen #1

A.D.S. MODE CHARACTER DATA

E F eccccc0000l

MITSURUGI 0% SOPHITIA 0%

SIEG 0% VOLD 0%

TAKI 0%

LEE 0% NINA 0% ROCK 0%

SOULEDGE 0%

HWANG 0% esre000eCCo ecccccco0o &

CLEAR:PRESS P41LEFT UP & P1 START

NEXT: PRESS P1 = =A-BUTTON

EXIT:PRESS P1B-BUTTON

A.D.S. Screen #2

Page 16

SOUL EDGE™ Kit Installation Manual

A.D.S. MODE CHARACTER DATA RATE TOTAL WIN LOSE MITSURUGI 0% SIEG 0%

VOLD 0%

SOPHITIA 0% TAKI 0% LEE 0% NINA 0% ROCK 0% SOULEDGE 0% HWANG 0% eco0ccee0e eoceooceooo0e eocoeoeceoce

CLEAR:PRESS P1LEFT UP & P1 START
NEXT:PRESS P1A-BUTTON
EXIT:PRESS P1B-BUTTON

A.D.S Screen #3

Page 17

Kit Installation Manual SOUL EDGE™

5.0 SOUND VOLUME ADJUSTMENTS

Two methods of volume adjustment are provided: a main adjustment on the System PCB, and, if wired in stereo, individual left/right control knobs located on the Service Panel. The volume may be set during bench testing by adjusting the PCB Volume potentiometer (located near the heat sink-mounted component). The Namco recommended setting is fully clockwise.

6.0 MONITOR ADJUSTMENTS

IMPORTANT Some monitors require use of an isolation transformer in the monitor power supply. Do not attempt to operate the SOUL EDGE PCB without this transformer or damage to the game PCB will result.
Page 18

SOUL EDGE™

7.0 PCB CONNECTOR TABLES 7.1. JAMMA EDGE CONNECTOR (56 Pin 3.96 mm pitch)

Po CGND TA Pp CGND TC a ee ee ee | insertion error preventing | H | ee eee

ee eee

2P “A” button 1 [ Zz | | 2P“B"button2 | a | 2P “GUARD” button3 |b | ee eee ee ee Po CCGND Te

+5V+5% 2.5Aor more, Notes: Do not connect leads to blank pins.

Connect the switches to N.O. terminals and +12V 5% Kit Installation Manual

Pa ft GND Pp 2 [GND

a a ee | 8 | -Coincounter 1 | [| 9 | Coinlockout 1 |

|_22 | 1P “A” button 1

2.0A or more

The lockout solenoid and coin counter operate on +12 volts

the GND to the COM terminal The +5V 2.5 A and +12 V 2.0 A supplies must be at + or - 5%.

Page 19

namco°: Kit Installation Manual SOUL EDGE™

7.2. EXTENDED EDGE CONNECTOR (48 Pin 2.54 mm pitch)

|Speaker R(-)[ At | Bi | a De =) COCA PCC A CSCS BS | insertion error preventing key | [C=C NS <=) [2PKickbutton | As [| Be | PP C~SC A PCC. [BO PCC a PCC Ta Xe = OY; SD = D1 = PA te CCA Bt CSCS Bi PCC TB [iP Kick button [| A20 [B20 | CSC Be PCC TB V0 = PC*CA BO Notes: © ¢ Do not connect leads to blank pins. ¢ For Stereo and Mono setting select the speaker output in the game option screen in test mode. « Monophonic cabinets output only left channel sound when the stereo sound setting is selected. Speaker connections e Connect the (L) speaker to the speaker output of 56 Pin JAMMA edge connector. e Connect the Right speaker to the speaker output of the 48 Pin edge connector.

Page 20

SOUL EDGE™ Kit Installation Manual

APPENDIX A: ILLUSTRATIONS and PARTS LIST

Page 21

SOUL EDGE KIT PARTS LIST Qty

SON COMESTOR CONNECTOR [SoRromaroD [HARNESS JASERRTT peearanrasae—[FoePOR HE

7 [wersaesroo [tage Fee

$040-04635-01 DECAL, CONTROL PANEL, (UNCUT) QO) fe} a s & c) fo) Q fe} r=) g a fy r=)

< Es) rr) pay rs) Ec cE E

o o

= EE

iy o

ro) al a al a

ej EEE o o

[Sow OeTSOT [DECAL ROR

a

[YeRrOSzTEOD | JSTOR FWAVESWAYRRGRSORER | 7 25 MANUAL, KIT INSTALLATION, SOUL EDGE 4

a fs)

=>

cE Ec o

oo ea

nN

@ »

Page 22

SOUL EDGE Control Panel Assembly $010-04679-00

PART NO.DESCRIPTIONNOPARTNODESCRIPTIONQTY
1$063-04678-00Controt Panel. Wood110VG80-00007-00Push Button, wiHorz. M-Switch, White, Legend: “2P*1
2‘$010-04679-00Control Panel, Metal w/studs11$040-04647-00Decal, Player 21
3$040-04635-00Decal, Control Panel OverlayT12VG80-03167-00Push Button, w/Hor M-Swiich, Yellow3
4$095-04680-00Cover, Control Panel, Plexigtass113S040-04645-00Decal, Kick “K"2
JVG20-04342-12‘Screw, Bin.-Hd., Torx, Sht. Mtl., Tamperproot, Bik, Oxide814S040-04643-00Decal, “B"2
6\VG20-02864-05‘Washer, Flat, #10, Steei, Zinc815$040-04642-00Decal, “A”2
tdVG20-02700-05‘Nut, Kep, 410-24, Steet,Zine816$040-04644-00Decal, Guard “G"2
8'VGB0-00006-00Push Button, w/Horz. M-Switch, White, Legend: “1P"17G80-03212-00Joystick, 4-Way/8-Way Black “Super”2
QS040-04646-00Decal, Player 1118vG20-02700-05Nut, Kep, #10-24, Steel, Zinc8
Page 23

SOUL EDGE Control Panel (Top View)

S010-04679-00

SOUL EDGE Control Panel (Side View)

$010-04679-00

Microswitch s Bracket (4 places) Nut (6) screw (2 places) (10 places)

__ (8 places) = = feast]

Page 24

REVISION, ur | Eco | DATE DESCRIPTION By _| APPR 1 2-12-96 | INTIAL RELEASE ve

PO-D | tee + + ++ 4? 4

(ims 150 Charcot Avenue

San Jose, California 95131

SOUL EDGE CONTROL PANEL

HOLE LOCATION

‘SIZE [DWG NO. REV. 2 | |

[FILE NAME SCALE FULL. Hove =|sneer_ 1 OF 1

DETAIL, 2 PLACES

Page 25

SOUL EDGE™ Kit Installation Manual

APPENDIX B: WIRING DIAGRAM

Page 26

vores. APPLY I8AVG FOR THICK LINES AnD Z2AVG FOR THIN LINES

2G. INDICATES RING. TERNAL 3 LABELS AME APPLIED TO BOTH SIDES OF S6 PIN comecTOR 4 KEYS ARE APPLIED ON BOTH 56 AND 4B PIN CONNECTORS.

1250-0. | MONITOR ' (u2000 | 20" CRT 1434600 ed

i I 00-£27¥0-0S71 B tor | set 1250-04345-00 JAMMA 56P (J1) LETTE

SSY '$050-04817~00 one

<

1250-04349-00 RIGHT SPEAKER 8 OHMS, 15 WATT LEFT SPEAKER 3250-04551-00 ~~ “SERVICE PANEL ASSY > & LEFT VOLUME POT RIGHT VOLUME POT “ =

250-04347-00

00-8¥S¥0~0S71 rue POWER ‘ SUPPLY 150W s SERVICE

nt .—s COIN ——-< ft] COUNTER | COIN DOOR “ASSY gavm>_VG50-03550-00 | co CONTROL PANEL ASSY - PLAYER 1 7250-04352-00 CONTROL PANEL ASSY - PLAYER 1250-04353-00 maMRCo 10 cool Aorse P-Serereri SOUL EDGE igie/264 WIRING DIAGRAM

m= be "5080~04857-00 A

Page 27

Seler warts tht ts printed cet bids and pats thereon are tee rom defects n o and workmanship under normal use and.service for a period. of ninety: (90)~ > days from the date of shipment. -Seller warrants:that its video displays (in games ~ supplied with video displays). are free from defects in material and workmanship under ‘normal use and service for‘a. period of thirty (30) days from the date of shipment. Norie ~ of the Seller's other’ products or parts thereof are warranted. Seller's: sole liability ‘shall : ‘ be, at its option, to repair, replace, bv isons .cele account tx otch prea ttc ace” Seer rome cited n wig upon covey y seal products are’ defective. % a Cre hs | Such products are rohumed prepaid Yo Seller's plant, ‘and: Seller's examination of said products discloses to Sellers satisfaction that t auch

: alleged ‘defects existed’ and not. caused . by accident, misuse, neglect,

alteration, improper repair, i installation, of improper! testing. :

“Inno event shall Seller be liable for loss of. profits, ee consequential damages, wot ne A x “Except for any express warranty set forth i in a vnitin coat betivoh Seller'and einer which \contract supersedes the’ terms herein, this warranty is: in Jieu., 5k aoe. warranties expressed or implied, including the implied warranties ‘of merckantability and’ ‘ fitness for a particular purpose, and ali other obligations of liabilities on the Seller's pat,» and it neither assumes nor authorizes any other'person to. assume for the Seller.

other liabilities in connection with the sale of products by Seller. ve oan

Namco America Inc. distributors are independent, being. privately owned and oferta In their judgment they may sell parts or accessories other than Namco ‘America Inc. '_ parts or accessories. Namco America. Ing. cannot be responsible’, for the- quality, - Suitability or safety of any non-Namco America, Inc. part or any modification including ~ -labor which i is vetoes bye such distributor. y

“Contact Namco America Ine. Customer Service at

14800) 326-4283 or FAX (408) 232-3060, - | Hours: 8: :00 am - “4: :00 pm PDT _ Parts and repair services for Namco America Inc. .. products are available through your distributor.

Page 28

. S . / ~ (g08)383-3900 ~ 450 Charcot Ave. San Jose, CA 95131 , >.) BAX: (408) 383-0128 -

  • ‘Technical Assistance ( ‘(@00) SASS Fae we a
  • 2523060