CATHODE RAY TOMES

Meadows 4-in-1

Meadows 4 in 1 (Meadows, 1976) · Document · 21 pages · 10 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

MEADOWS 4.UN

Model M-4

Page 3

Table of Contents

  • Introduction
  • Machine Set Up
  • Inspection and Service Access
  • Game Sequence

Attract Mode

Coin

Game Select

Paddle Select/Game Start

Game Select/Start

Duration of Games

  • Other Adjustments
  • Trouble Shooting

Diagrams & Illustrations

Figure 1 Joystick Adjustment

Figure 2 Joystick Assembly

Figure 3. Timer Settings & Free Game Score Settings

Figure 4 Coin Acceptor

Figure 5 Wiring Diagram

Page 4

INTRODUCTION AND WARRANTY INFORMATION

Meadows '"4-in One'' is a coin operated video device that simulates TENNIS,

HOCKEY, and another game called ''KNOCK OUT.'' "KNOCK OUT'' is a game

against time, where the player tries to clear the field of square targets

for a high score.

The electronics of this game incorporates the latest advances in semi-

conductor technology resulting in long life and low maintenance.

However - as with all devices mechanical or electrical - there will

inevitably be minor problems. This manual describes all adjustments,

repairs, and troubleshooting procedures which you will need to know to

operate the game.

WARRANTY,

Contact the distributor from whom the ge

purchased for warranty repair and/or replacement information.

NOTE: Any PCB repair attempted by anyone other than factory authorized

service people, or any damage due to improper handling or use

shall void any existing warranty. Proper procedures for

remo. and replacement, as outlined in manuel,

adhered to.

Display Monitor: Contact the distributor from whom the game

for warranty repair and/or replacement information.

Page 1

Page 5
NOTE:. Any monitor repair attempted by anyone other than factory

authorized people, or any damage due to improper handling

or use, shall void any existing warranty.

ALL EQUIPMENT RETURNED TO THE FACTORY MUST HAVE RETURN AUTHORIZATION

NUMBER AND TRAVEL FREIGHT PREPAID. PLEASE LIST SYMPTONS OF PROBLEMS

TO EXPEDITE REPAIRS.

NEW MACHINE SET-UP AND CHECK-OUT PROCEDURES

After uncrating, save all packing materials in the event the machine

aceds to be returned.

As each new '4-in One!'! leaves the factory, every component and sub-

assembly is carefully checked for proper operation. However, since

varts may have been damaged or factory adjustments changed due to

shaking and jarring during shipping the following check-out procedure

must be performed prior to placing the machine on location.

  • With the machine unplugged, open coin acceptor door and raise the top by removing wing nut hold down. Carefully inspect both the exterior

and interior for any obvious damage to the cabinet or internal components

which may have occurred during shipping. If any such damage is discovered,

immediately contact the freight carrier.

  • Inspect the interior of the machine more carefully, looking for

broken or disconnected wires, sub-assemblies not securely mountes. soc

Page 6

any foreign objects shorting or interfering with electrical connections.

Pay particular attention to the connections to the TV monitor, the

players' controls, and the coin switch. Check the security of the

computer PCB edge connectors.

  • Plug the machine in and check the CRT (Cathode Ray Tube) image

which should be steady, centered, sharp, and exhibit the proper levels

of brightness and contrast. With the machine plugged in, but not

started, the CRT will display the Attract Mode (see next section for

Attract Mode explanation).

  • Insert several old and new coins into the coin acceptor. Wo genuine

coin should be rejected. Operate the coin return button while checking

for signs of stickiness or binding. Lightly spray the coin acceptor,

return button and the inside of both lock cylinders with WD-40, a sili-

cone lubricant.

  • Check the computer for proper operation by playing several games and

compare the results with the game sequence analysis in the next section.

INSPECTION AND SERVICE ACCESS

Access to ''4~jn-One!' is gained by first unlocking the coin door and

tilting it out. It will stop by means of its retaining cord. Then

unfasten the wing nut that holds the top down, which is located just inside

the coin door and up high. Now lift top of machine up to open. This

Page 7

allows removal of the Logic PCB, monitor and joystick assemblies as well

as Cleaning of the screen and joystick pots.

GAME SEQUENCE

When the game is first plugged in and the picture tube is allowed to

warm up, it will display an attract mode that automatically changes

from one game to another. The ball will atso be bouncing off of the

borders and "Hockey! face off area. When a coin or coins are inserted,

the games will stop changing and will allow the player to manually

change the games.

One coin (25¢) yields:

Two Player Tennis, or

Two Player Hockey, or

One Player Knock Out

Two coins (50¢) yields:

Four Player Tennis, or

Four Player Hockey, or

Four Player Knock Out

Came Select button is now pressed until the desired game is visible on

the screen.

Page 8

4, Paddle Select/Game Start

Paddle Size Button, either "Expert! or '"Pro'' is now pressed and the

game begins.

  • Game Select/Start, after Free Game (or Extended Time)

The One Player mode of the game ''Knock Out'' is equipped with a free

game feature. When the free game score is reached and the time runs

out, the game will hold the players score for about 2 seconds and

then clear the score out allowing the player to select any one coin

credit type game. As before, the game select switch is pressed and

then the Paddle Size/Start Game switch. A free game can only be

obtained once for every coin inserted. Free game scores are operator

selectable to 100, 200, 300 or 400 points. Setting of the free game

score will be covered under adjustments.

S. Duration of Games

Tennis: The length of the Tennis game, either 2 or 4 piayers, is

determined by which player reaches a score of 11 first.

Hockey and Knock Out: The length of play on these games is determined

by a visual time line on the monitor screen. This time is selectable

to either 1.1, 2.2, or 4.4 minutes as described on the illustration,

"Logic PCB."

Page 5

Page 9

OTHER ADJUSTMENTS

For the following adjustments, see illustrations,

Ti

tn the Knock Out and Hockey games, the time may either be adjusted to

1.1, 2.2, 4.4 minutes. See Figure 3.

Free Game Threshold

On the Knock Out game, the free game score may be adjusted to 100, 200,

300, or 400 points. See Figure 3.

For reference the lower side of court is nearest coin operator. The

upper sides of court are as you face the coin operator.

Paddle should be checked every service call. Paddle will need adjusting

when a pot or logic board has been replaced. If a pot has been replaced

refer to section on preliminary adjustment. Each paddle has two adjust-

ments: See Figure 1.

The joystick pots need preliminary adjustment if the pots have been

replaced. Preliminary adjustments should be done before the joystick

is remounted.

Page 10

a, ADJUSTING 2 PLAYER JOYSTICKS: Rotate pots of joystick Counter-

Clockwise until the stick is forced to move and the pot will not

rotate any further. Now apply slight pressure to the stick and move it in

a circular motion. The joystick is ready for mounting in the unit. Wires

must be connected to terminals #1 and #2 on the pots.

b. ADJUSTING 4 PLAYER JOYSTICKS: Rotate pots of the joystick Clockwise

until the stick is forced to move and the pot will not rotate any further.

Now apply slight pressure to the stick and move it in a circular motion.

The joystick is ready for mounting in the unit. Wire must be connected

to terminals #2 and #3 on the pots. To complete adjustment see Figure 1.

TV_MONITOR ADJUSTMENT

The TV monitor adjustments function like those of a home T.V. Set.

Refer to monitor manual for the locations of the following adjustments.

a. VOLUME: Adjust the volume to the preference of the location.

Keep in mind that the machine will sound louder with the control panel

raised.

b. BRIGHTNESS: Brightness is adjusted before contrast. Adjust so

the CRT background is as dark as possible without diminishing the

brightness of the playfield walls.

Page 11

c. CONTRAST: Adjust so that the CRT images are as bright as possible

against the pre-adjusted dark background without blurring.

d. VERTICAL HOLD: Adjust only if the picture appears to be rolling

up or down the screen. Adjust for a stable, centered picture.

e. HORIZONTAL HOLD: Adjust if the picture appears to be shifted off

center horizontally, the images are warped, or if the whole picture

is broken into diagonal lines.

COIN ACCEPTOR OPERATION, ADJUSTMENT AND MAINTENANCE

The detection and rejection of undesired or counterfeit coins are

determined by size (both thickness and diameter), weight, and

metallic composition.

The transfer cradle (#9 in Figure 4) is used to test both the size and

weight of the coin. The quarter must first pivot an “undersize'! lever

  • to unlock the transfer cradle and can be returned by actuating

the wiper operating lever (17). Oversize diameter coins will fail to

pass between the transfer cradle and the wiper and can be returned by

operating the wiper lever. Coins that are oversize in thickness will

fail to pass between the magnet gate (11) and the main channel (5) and

will have to be dislodged by actuating the wiper operating lever.

Underweight coins will fail to cvercome the transfer craale counter-

weight and ca be returned by operating the wiper lever.

Page 12

A magnet is used to test the metallic composition of the coin.

Highly magnetic coins, such as steel or iron, will be retained by

the magnet and can be returned by actuating the wiper operating lever.

Coins having comparatively high magnetic properties will be slowed

down by the magnet and will drop off the rail short of the Accept

entrance and will be returned. Coins having little or no magnetic

properties, such as brass or zinc, will pass through the magnetic field

so fast they will overshoot the accept entrance and will be returned.

ADJUSTMENT.

All coin acceptors leave the factory adjusted for maximum performance.

If, however, more critical adjustment is desired, or if the unit has

been disassembled for cleaning, the fotlowing adjustment procedure is

suggested.

a. Set the acceptor on a level surface with the back of the unit facing

you (the kicker and separator are on the back).

b. Loosen the screws holding the kicker (1) and the separator (3) and

move both the kicker (2) and the separator (4) as far to the right as

they will go. Tighten the screws lightly.

c. Insert several test coins (both cld and new) and note that some are

returned by striking the separator.

Page 13

d. Loosen the separator screw and move the separator a slight amount to

the left. Retighten the screw.

e. Insert the test coins again, and if some are still returned, repeat

Step D until all coins are accepted.

f. Loosen the kicker screw and move the kicker a slight amount to the

right. Retighten the screw.

g. Insert the test coins again and if some of them are returned, repeat

Step F until all coins are accepted.

h. Be sure that both screws are tight after the adjustments have been

made.

THE MAGNETIC GATE

a. Set the acceptor with the front of the unit facing you in the test

position.

b. Turn the magnet gate adjustor (12) out (counter-clockwise) until

none of the coins will fit through.

c. With a coin resting in the transfer cradle, turn the adjustor in

(clockwise) until the coin barely passes through the magnet gate.

Page 10.

Page 14

d. Test this adjustment using several coins, and if any fail to pass

through the magnet gate, repeat Step C until all coins are accepted.

e. Fix the magnet gate adjustor in this position with a drop of glue

or Loctite, if necessary.

ACCEPTOR MAINTENANCE

Depending on the environment in which the acceptor is used, periodic

preventative maintenance should be performed.

The mainplate (5) may be cleaned with any household cleaner. Thorough

rinsing and drying are necessary to remove deposits and/or film. Re-

move all metal particles from the magnet by guiding a screwdriver along

the edges of the magnet. Remove the transfer cradle and undersize lever

and clean the bushings and pivot pins and bushings and re-assemble.

Spray the entire unit lightly with WD-40, a silicone lubricant.

TROUBLE SHOOTING HINTS

TESTING COMPONENTS OF GAME

Buttons & Coin Switch are normally open. When pushed they are closed.

The buttons can be by-passed by touching the wires together.

Page 11

Page 15

Harness can be tested by an ohm-meter or continuity checker.

Fuses are checked by a visual inspection or continuity checker.

Logic Board & T.V. Monitor can be checked by substitution of a good

replacement. Repair of Logic Board & Monitor should only be serviced

by experienced technicians.

NO PICTURE: Check if back of picture tube is lit. If not, inspect

fuses, power cord, and power outlet. If these are good and tube is

not lit repair of monitor is necessary.

If the tube is lit, check adjustments of brightness and contrast.

Test continuity of logic board pins #1 and #3 (5 volt de power

supply), and pin #5 (Video output). If all check out, problem is

either the logic board or monitor.

NO SOUND: Check adjustment of volume control on T.V. monitor. Test

continuity of logic board pin #17 (audio signal), and monitor pins #5

and #8. Check speaker; logic board, and T.V. monitor.

NO PADDLES: Check paddle adjustment. Test continuity of wires, from

pots to logic board. The game may not be resetting properly. Check

coin switch and wires. Check pots and logic board.

Page 12

Page 16

PADDLE DEFECTS: If paddles appear and are jumpy, oscillating, flickering,

or will not stay within its boundaries, pots may need adjustment or

replacement.

GAME DEFECTS: If game is not operating properly, for example: incorrect

scoring, segments missing, erratic ball movement, the likely cause is the

logic board.

SPEED BALL: Check speed buttons and wires. Check logic board.

Page 13

Page 17

MEADOWS 4-IN-1 PADDLE ADJUSTMENT PROCEDURE

A. Start game of 4 PLAYER HOCKEY with ''Pro'' size paddles.

B. To adjust HORIZONTAL paddle travel begin by positioning the joystick in its leftmost position. Next turn the adjustment ears on the joystick for the paddle's "horizontal" paddle position pot counter clockwise until] the paddle is unaffected by further turning. Now back off on the adjustment you just made until the paddle begins to move to the right. At this point a correctly adjusted black paddle will be adjacent to the left border and the white paddles at an imaginary line that passes between the left score digits.

Now move the joystick to the full right position. Turn the appropriate "H JOY'' adjustment on the PCB until the paddle has gone as far to the right as the adjustment will take it. Next, back off until the paddle just begins to move to the left. At this point a correctly adjusted black paddle will be at an imaginary line that passes between the right score digits, and a white paddle will be adjacent to the right border. Check the paddle travel and repeat if necessary.

C. Start game in the 4 PLAYER TENNIS Mode.

D. To adjust VERTICAL paddle travel begin by positioning the joystick in the full up position. Turn the appropriate ''vertical'' paddle position pot on the joystick counter clockwise until the paddle no longer moves up. Back off on the adjustment you just made until the paddle starts to move.

.Place the joystick in the full down position. Turn the appropriate ''V JOY" adjustment on the PCB until the paddle no longer moves downward. Back off on this last adjustment until the paddle just starts to move upward. Recheck the paddle travel and repeat if necessary.

H JOY 1 for adjustment H JOY 2 of peddle HJOY 3. rightmost Himit White paddles may travel horizontally within this HJOY 4 -v JoyT fe adjustment zone. They cannot move outside of it, ~V JOY 2 of paddle rR —— V JOY 3 bottom limit ~— a

AI paddles should be able to move vertically from top border to bottom + is border, They cannot move beyond the borders.

Block paddles nay travel horizontally within this zone. They cannot_move outside it.

used to adjust poddle topmost position limit. Joystick 3 Joystick #4 horizontal poddte position pot “] used to odjust poddte leftmost position limit. top view of table

Page 18

we eS aie

JOYSTICK ASSEMBLY EXPLODED VIEW

FIGURE 2

Page 19

Timer is factory set at 2.2 minutes To change timer

Time setting

For 1.}? minutes connect jumper wire between A to D For 2.2 minutes connect jumper wire between A to C For 4.4 minutes connect jumper wire between A to B

TIMER OPTION SETTINGS

FREE GAME SCORE OPTION SETTINGS

Free game credit factory set at 200 points. To change to below options connect jumper wire at following points:

Free game score

100 - Connect jumper wire between B to 200 - Connect jumper wire between A to 300 - Cofinect jumper wire between A to hoo ~ Connect jumper wire between C to and B to E nmooMm

FIGURE 3

Page 20

KICKER SCREW KICKER

SEPARATOR SCREW

TOR

ATE ASSEMBLY

SEMBLY

VE RPLATE ASSEMBLY

Same nonen NY

COIN FACE PLATE

FIGURE 4

COIN ACCEPTOR — EXPLODED

Page 21

2 PLAYER 4 PLAYER

“WOH LHOIY

Luan HOY

“YOH “L437

LY3A 1377

"MOH LHOTY

“Luan LHOIY

“YOH 1337 Luan Ky 1437 por RIGHT SPEED | | 7 boo © ror Oe LEFT SPEED oa | GAME SELECT A) ¢ NOVICE - | pee ée

EXPERT One

PWA EDGE

i CONNECTOR 39) | COIN COUNTER | CONNECTOR |

POWER

CONNECTOR

117 Vv AC