CATHODE RAY TOMES

Space Tactics

Space Tactics (Sega, 1981) · Manual · 60 pages · 32 sections · original scan

Page 1

OWNER’S MANUAL

Manual Part No. 420-0556

Page 2

Grem n/SEGA

Owner’s Manual

GREMLIN INDUSTRIES, INC. 8401 Aero Drive San Diego, CA 92123 (714) 277-8700 TLX:910-335-1621 SEGA ENTERPRISES, LTD. No. 2-12 Haneda 1-Chome Ohta-ku, Tokyo, Japan 144

  • 742-7312 TLX: SegaStar 22357

SPACE TACTICS OWNER’S MANUAL Copyright © 1980 by GREMLIN®/SEGA®, All Rights Reserved

i

Page 3

Introduction Game Concept. . Game Specifications .... 00.0.0 c cece 1 A. Shipping Bracket Removal . B. Game Inspection.......... C. Connecting Game Halves D. Game Power-On ...... Theory of Operation ... Logic Board Diagram .. . Maintenance Procedures . .

  • General Service Tips
  • Power Supply ... =
  • Sound Board ........ 606 c ccc ccc cnt e eet n tence 4, Power Amplifier .....0.0 0.000 etn eens
  • Logic Board .. Game Adjustments . .
  • Mirror Motor ...............0.004-
  • Monitor Motor ..........0. 00.00 ccc eee eee
  • Alignment of Mirror and Motor During Self-Test
  • Steering Handle
  • Monitor Removal .......
  • Miscellaneous Adjustments . Parts Catalog...........-...04.
  • Complete Assembly ......
  • Recommended Spare Parts . SCHEMAHES. os a ccs wines 2 gow eee +o ed EH a ENYA e mene soe oe ee uimnne
Page 4

introduction—

how to use this manual

The following manual is designed to instruct you in the trouble-free operation of your new Space Tactics game. Please take the time to read it through carefully before using your game. This manual assumes the maintenance technician possesses a general knowledge of solid state circuitry, microprocessor and digital integrated circuitry, and TV monitor concepts. Any individual not knowledgeable in these areas should not attempt repair of the electronic portion of the game. The manual is organized in two main sections—electronic assemblies and electro-mechanical assemblies—which contain detailed service and parts information. After reading the manual through first, you will then be familiar with the proper assembly section to refer to if a problem should occur. If you have any questions that are not answered in this manual, call GREMLIN/SEGA Customer Service, (714) 277-8700.

iii

Page 5

Space Tactics is the newest video game from GREMLIN/SEGA. It is a sitdownstyle game, surrounding the player with the game action. The object of the game is to destroy the attacking space ships one by one in order to defend the five player bases at the bottom of the screen. At the beginning of each game, the player's bases are armed with one missile each which destroys the bombs dropped by the enemy ships. These are controlled by the five red switches on the game front panel. By moving the steering handle, the player aims his laser beam at the enemy ships. His aim must be exact to destroy the ships. The handle allows the player to aim at all parts of the screen. At the game's beginning, the player receives 4 or 6 basebarrier defenses, which he must use carefully throughout the game. The basebarrier is a yellow arc that runs over the player's bases and prevents enemy bombs from reaching the bases; it is activated with the yellow front-panel switch. But, a bomb that hits the barrier will explode and make a hole in the defense. The player must destroy all enemy ships in each round to advance to the next round. Each of the 3 kinds of enemy ships is worth a different point value, depending on the round. At the end of the first round, one UFO appears and must be hit to gain a bonus point value. The sooner this ship is hit, the higher will be the points awarded. At the end of the second round, 2 UFOs appear. Play continues until all the bases are destroyed by the enemy; when this occurs, the game ends. Options selection for Space Tactics

game concept

allows you to select the number of coins and credits for each coin mechanism, number of barriers, bonus barriers, (1 or 2 extra each time a player destroys all invaders and the UFO), player initials entry, advertising sound on/off and extended play. The extended play feature occurs only if 2 or more credits are on the game. Refer to the Options Selection section under Miscellaneous Adjustments in this manual for instructions. Also, at the end of every game, the screen displays the top 5 high scores, and allows entry of a player's initials if he is one of the high scorers.

game

specifications

Power 90-120VAC, 175 watts 100-240VAC, 175 watts

31W X 69 inchesD (77cemW X 171cmD) Dimensions:

Height 63 inches (157cm)

Page 6

. Shipping Bracket Removal After the game halves are out of their cartons, you must remove the shipping brackets and bolts before operating the game. Refer to the drawing to locate these brackets and bolts. The only tools required are a Phillips-head screwdriver and a cresent wrench. Remove the brackets carefully, so that the FRAGILE GLASS MIRROR does not break. Loosen and remove the 2 shipping bolts located at the bottom of the monitor. When moving the game at any time, we strongly recommend that these brackets and bolts be put back, as a precaution against shipping vibrations. b.Game Inspections After all shipping brackets and material have been removed, inspect the game against the following check-points: (DO

REMOVE—shipping bracket _

game set-up and inspection

NOT TURN THE GAME ON YET!) Check: [Cabinet not damaged. Glass mirror not broken or cracked. GNo wires loose from plastic connectors. CiLogic and sound boards seated properly. {Monitor mounted securely. Monitor boards seated properly. CiConnectors are attached properly.

These are problems that could occur during shipment. Be sure to check them before turning on the game. Report any serious problems to GREMLIN/SEGA Customer Service, or your distributor.

’ipping bolt (2 ea.)

REMOVE—shipping bracket (2 ea.)

Page 7

€.Connecting Game Halves Position the front and back halves together, leaving about 6 inches (15 cm) of space between them. Now, insert all plastic connectors from each half. All the leads and connectors are color-coded, so there will not be a mistake in making the connections. Be sure to insert the male/female connectors firmly. When all leads are attached, tuck the wiring inside the rear half of the game to be certain that no wires hang out when the cabinet halves are brought together. Now, push the game halves together and insert the enclosed Allen-head bolts (located in the cash box) into the following positions: 1 bolt on the right side of the game. 1 bolt on the left side of the game. 3 bolts on the top of the game. 3 bolts on the bottom, below the steering handle. (8 bolts used, total). It is suggested the game halves be joined on a smooth floor surface for easier maneuvering. Adjust the cabinet leg levellers under the game, as needed for your location. Two handles are provided on the rear of the front half for moving the game. d.Game Power—On Now you are ready to turn on your Space Tactics game. Plug in the game and turn on the power switch located on the rear side of the game. The following sequence should occur: 1.The monitor and mirror assemblies will move slightly to center themselves before the game starts. This occurs every time the game is turned on. If the monitor or mirror do not move, it may only mean they were already centered.

  • The two ultraviolet fluorescent lights will come on.

(Do not look directly at these lamps—ultraviolet light can harm the eyes! Also do not expose the logic board to the lamps—ultraviolet light erases Eproms!)

  • If everything is normal, the monitor, at power on, displays random information. A few seconds later, this clears and the game goes into the advertising sequence, first displaying:

GAME OVER

If there is a mechanical problem; the screen displays:

MECHANISM IS NOT READY

Consult the Maintenance section of this manual for further instructions.

Page 8

Space Tactics is a unique combination of video-game and electro-mechanical circuitry. As a video game, it possesses the essential elements of any video computer: 1.A microprocessor 2.Memory circuits

  • Clock and video timing circuitry
  • Input ports
  • Output ports
  • Power circuits 7.Video and character generation circuitry But, what makes Space Tactics a special kind of video game is its electromechanical system controlled by the computer. More about that system later. First, let's look briefly at each of the essential elements above and where they are located in the game. (Refer to the Logic Board Block Diagram for reference.)
  • Microprocessor: (Page B of Schematics) The microprocessor used in Space Tactics is an 8080A. It is IC 138 on the logic board, and is the heart of the computer. It controls the movement of data and instructions to and from memory and the outside world.
  • Memory Circuits: (Pages C, D, and E of Schematics) Basically, there are two types of memory devices: 2716 Eproms (8), and 4027 RAMS (32). The Eproms hold the program instructions for the microprocesor; they also contain character information. The RAMS form the video memory and they are divided into 4 Pages of 8 RAM ICs each. (A Page is a section of memory designed to hold certain video information.) The Pages in Space Tactics memory are labelled “B’, “D", “E” and “F’.
  • Clock and Video Timing Circuitry:

game theory of operation

(Page G of Schematics) The Master Clock circuitry consists of a crystal and IC 143. The clock signal generated by this circuit not only drives the microprocessor, but also the video timing circuits 123, 118, 116, 117, 121, and 122.

  • Input Ports: (Pages F, H and I of Schematics) Input ports allow the computer to sense the player's actions on input devices. Refer to the Maintenance section for a list of these parts and ICs. Note that the photo-sensing units used in the game are considered input devices, also.
  • Output Ports: (Pages F, H and I of Schematics) Output ports allow the computer to respond to the player's actions. The Maintenance section lists the output ports and ICs. Note also the addition of 2 output devices not commonly found in video games—the 2 motors.
  • Power Circuits: (Page E of Schematics) Voltage requirements for the game's logic board are +5 VDC, -5, +12, +6.8 VDC and +8 VDC. The last two voltages provide power for the 75468 transistor array ICs; 6 VDC also powers the coin counter and coin rejects coils.
  • Video and Character Generation: (Pages C, D and F of Schematics, also see block diagram of logic board) The circuits that produce the color video patterns on the screen consist of not only the video RAM (4 Pages), but also the following:
  • Address Multiplexers
  • Video Memory Controller
  • Character Generator d)Color Prom (RGB outputs)
Page 9

LOGIC BOARD DIAGRAM

VIDEO TIMING

|- — — i LOGIC

CLOCK,

CPU memory CRT beam

address position addr.

address bus WRITE

(16 lines) 3 Re; [ADDRESS ' j '

READ- READ- | REFRESH

) COLOR ONLY | MEMORY PROM MEMORY MEMORY | (CONTROL: > ‘ x |

CPU VIDEO |

a 8080 REFRESH

MEMORY ' RGB

(READ-WRITE) CHARACTER OUTPUTS

data bus J GENERATOR (8 lines) MEMORY (READ-ONLY) | L

TIMING & INPUT OUTPUT| CONTROL PORTS PORTS

LOGIC LS

ready player controls

tL opto- isolators SPACE TACTICS

< < LOGIC BOARD: BLOCK DIAGRAM.

rod + Ve sound board motors

Page 10

The address multiplexers are 74LS153 ICs located (on the schematic) to the left of each of the four RAM pages. They allow the computer to address the RAMs at one time, and, at another, allow video timing to address the RAMs. This process of switching between the computer and the video timing updates, or refreshes, the information in the RAMs. The action occurs so fast that the video data changes on the screen smoothly and rapidly. The Video Memory Controllor is part of the video timing circuitry that ensures the switching process does not occur at the sarne time. Character Generation is produced from a portion of Eprom that contains the information for the various characters in the game. The color Prom, IC 86, generates the pulses, on command from video memory, that produces the Red, Green, Blue (RGB) signals for the color monitor. Now that we have identified the essential elements of the Space Tactics computer board, let's see how the whole system works together. Player responses on the input devices, and the computer responses on the output devices are all monitored and controlled by the game's computer. This applies to the electro-mechanical system as well, because

itcontainsinputdevices(theopto-

isolators) and output devices (the motors) which the computer senses and reacts to.

So,thinkoftheelectro-mechanical

assemblies in the game as different kinds of input and output devices, like sound boards and monitors (output devices) and

coinandplayerswitches(input

devices)—that is what they are. The electro-mechanical system, then, works in the game as follows: One motor controls the movement of the mirror assembly up and down, and the other motor moves the monitor left and right. These motions are activated by the steering handle. For example, when the handle is turned to the left, the computer senses this switch is closed and causes the motor circuit to turn on the motor. You will see there are four motor circuits on the logic board; two control the directions, clockwise or counter-clockwise, of the mirror motor, and two control the directions of the monitor motor. The game computer senses the direction and position of both the mirror and monitor assemblies. It must do this continually, or the game would not respond accurately to the player's commands. So, two opto-isolators sense the up/down limit of the mirror, and two micro-switches sense the left/right limit of the CRT. When one of them is activated, it tells the computer that the CRT motor, for example, cannot move left anymore. As reference points for the computer, one opto-isolator informs the computer of the mirror’s center position (halfway mark) and one tells of the CRT’s center position. This is why both motors activate on game power-up: They simply center the mirror and monitor for the next game. Finally, two notched sensor discs on both motor shafts rotate between optoisolators to generate a string of pulses. The computer counts the pulses and keeps track of the positions of both the mirror and monitor. This occurs so that the computer knows, for example, where and when the player laser shot hits the screen. Now, you can see how the mechanical system in the game works: It consists of input and output devices not commonly found in video games, and, as such, they are all under game-computer control.

Page 11

maintenance procedures

Page 12
  • General Service Tips If, when the game is first turned on, the screen displays:

MECHANISM IS NOT READY

and you have done all the steps in the Game Set-Up section of the manual, open the service door on the side of the game's rear half, and inspect the monitor center sensor (see figure 2). Make sure its wires are connected and that the black optoisolator is not defective. Re-solder any loose wires, or replace the bad sensor. If this fails to start the game, make the same checks on the mirror sensors, located on the top of the mirror motor assembly (see figure 1.) (The game halves need to be separated in order to make this inspection). If these check good, turn off the game and manually turn the monitor and mirror to their center positions. Now, re-power the game: If “MECHANISM IS NOT READY” comes on the screen again, proceed to check the two motors. Make sure they are not jammed and are connected properly. If this fails to solve the problem, suspect a problem on the logic board. Refer to the logic board maintenance section, following.

Z. Power Supply Repairs (Refer to game block diagram (page A) and schematics (page E) The power supply design is straightforward enough to locate any problem quickly. Three IC voltage regulators supply the DC voltages; 2 ICs (IC1 and 1C2) supply +12 volts, one (IC3) supplies -5 volts. The switching regulator unit supplies +5 volts at 6 amps. In addition, +17 volts is taken from the rectifier D4, +8 and +6 (unregulated) volts from the last two diode rectifier circuits. If a voltage problem occurs, check the output at the power supply for the proper voltage. If the voltage is still not present, disconnect the supply lead at the power supply and measure the voltage again. If the voltage reappears, you should suspect a problem (probably a short) on one of the IC boards. If the voltage does not show up, suspect the diode bridge or IC voltage regulator.

  • Sound Board Repairs (Refer to sound board schematics and game block diagram) When one or more sounds is missing, it is best to isolate the particular defective sound circuit on the sound board. Refer to the block diagram for the list of sound types and pin connections to the sound board. Activate the problem sound circuit and, on the sound board, look for any transistors that do not switch states when activated, or check ICs that should change states, or should generate clock signals. Also, check both inputs and outputs to IC amplifiers for the presence of signals. Refer to the diagram below to adjust the sound board controls.

VRI_ VRS VRS VRT VRO VR RIS Agbe Aen hn ham VRE WR4 WRE VRB RIC VRIC

SOUND BOARD m 7 4ZU=P

VR 1. Explosion Lower Sound Volume VR 2. Not used VR 3. U.F.O. Hit Sound Volume VR 4. Explosion Upper Sound Volume VR 5. Bomb Sound Volume VR 6. Player Shot Sound Volume

Page 13

VR 7. Invader Sound Volume VR 8. Warning Sound Volume VR 9. Invader Hit Sound Volume VR 10. Rocket Sound Volume VR 11. U.F.O. Sound Volume ‘VR 12. Character Sound Volume VR 13. BBD (Echo) Sound Volume VR 14. BBD Bias Volume

  • Power Amplifier Repairs (See diagram below) There are two power amplifier boards in the game, one for the upper speaker and one for the lower. First, isolate which of the two amplifiers is defective by turning down the volume of one, while keeping the volume of the other high. Reverse this procedure to isolate the defective board. Check for the proper voltage level on the board (+17VDC) and for ground potential. If these are present, trace an audio signal through the amplifier circuit and verify whether it is present on the output. If not, the IC is probably defective, or one of the coupling capacitors is bad.
  • Logic Board Repairs (Refer to schematics, page B through 1)
  • Built-in Self-Test Feature: The Space Tactics logic board has a built-in self-test program which is activated by flipping the switch labeled “SELF-TEST”. This switch is located on the power supply board in the rear of the game, and inside the coin entry door, at the top. The self-test checks for a bad RAM in one of the four RAM Pages. (Each Page contains 8 RAM ICs). It also checks for any defective switch or display on the game front panel. To run the test, turn off the game, then turn the self-test switch on, re-power the game, and observe the following screen displays:
  • The screen displays, in this order: a red screen a yellow screen a green screen a red screen ii) Then, 30 seconds later, a small yellow "X” appears inside a red border. The laser beams begin to fire. This allows you to check for proper operation of the laser beams. The “hit” LED (red) and the yellow “X” should line up exactly, otherwise the mirror or monitor assembly needs adjustment. (see Game Adjustments) iii) The switches on the front panel light up. Each of the LED segments in the BAR displays light up, one at a time. Watch for any burned-out LEDs or lamps at this time. Also, the score displays count 0 through 9, allowing you to check them for proper operation. Next, activate each switch and its light should go out, showing that the switch is good. iv) If a RAM is bad, for example, in the "Dy" Page, first the screen displays:

D PAGE RAM Is NO GOOD! RIGHT 0000 0000 ERROR 0000 0010

D PAGE RAM IS NO GOOD! RIGHT 1111 1111 ERROR 1111 1101

7654 3210 :RAM Number

Page 14

RAM¢# 0

RAM PAGE (8 RAMs each)1234567

B - 1cs2_-83—BACSHA GT

D6061626352535455
E-_37.38394030s3S3
F1718192010111213

In the first readout, a “1” appears in the ERROR row, indicating a bad RAM. The second display occurs only to verify the first display, by inverting the first display. So, a “O” appears here, showing the same bad RAM. The RAMs in each Page are numbered O through 7, with the 0 RAM at the far right, as shown above. Refer to the chart above to locate the correct RAM IC on the logic board: So, our example shows RAM #61 is defective. Change the defective RAM and run the test again to verify the replacement. The RAMs are grouped into their respective Pages on the logic board. NOTE: If there is a bad RAM in the “B Page”, the display will not clearly show this, because “B Page” is the memory devoted to displaying words and letters. Isolate the bad “B” RAM further with an oscilloscope by looking for a floating, pulled-high or missing signal on the suspected RAM output, pin 14. IMPORTANT: To return to the game mode, you must first turn off the game power, turn off the test switch, then re-power the game. Failing to turn off the game before deactivating the test switch, could cause an erratic display.

  • Defective Screen Displays: As was mentioned, each Page of RAMs performs certain display functions. They are:

Page B Displays: Character (words/letters) display Player bases Barrier (yellow arc above bases) Bomb (from enemy invaders) Page D Displays: The enemy invaders that appear in the back of the screen playfield Page E Displays: The invaders that appear in the middle of the playfield Page F Displays: The closest invaders, when they enlarge The UFO saucer So, if a problem occurs where some or all the above pictures are defective, suspect the RAMs or multiplexers in the corresponding Page.

  • Defective Player Controls: (Refer to input ports schematics) Suspect the ICs listed below as bad if the corresponding input switch fails to operate, but the switch is good.

INPUT PORT IC # (on logic board) INPUT SWITCH C1 1, 7, 80, 87, 35 1, 7, 72, 66, 35 Fire Switch Move Right (Steering Handle) Move Left (Steering Handle) Move Up (Steering Handle)

CRT: Right Limit Switch 1 Move Down (Steering Handle)

CRT: Left Limit Switch 34 CRT: Center Opto-isolator 34 Mirror: Right Limit Opto-isolator 34 Mirror: Left Limit Opto-isolator 34 Mirror: Center Limit Opto-isolator | 14, 22 (2) CRT Clock Pulse (CP) Opto-isolators

Page 15

INPUT PORT IC# (on logic board) INPUT SWITCH

, 22 (2) Mirror Clock Pulse Opto-isolators Dip Switch #1 Dip Switch 2 Steering Handle Switches for Entering Player Initials Only Coin Switches 1 and 2 Service Switch Self-Test Switch

  • Base Switches Start Switch Barrier Switch

Be sure to verify a suspected optoisolator as bad before replacing its input port IC. Do this by holding a logic probe, or oscilloscope probe to the output of the device. Then, slip a dark-colored piece of paper between the opto-isolator and observe a voltage change at the output. If no change occurs, the opto-isolator is probably bad.

  • Defective Output Control: (Refer to output port schematics) Refer to the list below to locate a defective output IC (or other part) for the corresponding output device.

OUTPUT PORT IC # (on logic board) OUTPUT DEVICE 1C2, XSTR TR22, 1C159, Photo- Coupler PC4, DIAC 4, TRIAC 4 1C2, TR23, IC159, PC3, DIAC 3, TRIAC 3 IC7, 1C8, TR20, 1C159, PC2, DIAC 2, TRIAC 2 1C8, TR21, IC159, PC1, DIAC 1 TRIAC 1 ICs 95, 96

ICs 139, 136, 126, 119, 125, 140, 132, 131, TRs 16, 17, 18, 19 ICs 43, 42, 58, 49, 57, 99 ICs 114, 109, 103, 97, 102, 108 TRs 1, 2, 3, 4, 5, 6 ICs 102, 108, TRs 7, 8, 9, 10, 11, 12, 13, 14, 15, ICs 65, 99 CRT Motor, Turn Right

CRT Motor, Turn Left

Mirror Motor, Down

Mirror Motor, Up

Lights in Barrier, Start and Base Switches Laser Beam (Both Sides)

Sounds Enable (To Sound Board) Score Displays

Barrier, Round, and Credit Bar LED Displays Coin Counters 1 and 2, Coin Reject Coils 1 and 2

Page 16

One of the more unique output devices in the game is the LED laser beams. It consists of two boards, each of which contains 60 green LEDs of three sizes. Refer to page F of the schematics to see how it operates: IC 94, a 74LS165, is a shift register that receives 8 bits from the data bus and clocks them out in series at pin 9. These pulses ("LED CP”) are applied to pin 1 of IC 140 (page J of schematics). Depending on the 8 bits loaded into IC 94, the shift register, the clock pulses will appear to make the LED laser beams move fast or slow. If the enemy invaders on the screen are far away (as in the beginning of the game), the laser beams appear to move slowly. When the invaders are close, the beams seem to move faster. Eprom #217 (IC 136, page J of schematics) outputs the correct sequence of data to the 75468 transistor arrays, #125 and 119. They, in turn, activate the LEDs on the laser beam boards in rapid succession.

  • Static Problem: (See page B—CPU schematic) The logic board contains a circuit that resets the microprocessor (IC 138), if a large static charge is applied to the game. This circuit consists of an antenna and ICs 155 and 151. The antenna picks up the static charge and triggers the ICs to reset the 8080A. If this circuit is too sensitive to static, add a 3300 (3.3K) ohm resistor at R53 on the logic board, and this will decrease the circuit's sensitivity. Also, the antenna wire can be shortened, or removed, if necessary.
Page 17

game adjustments

Page 18

The following adjustment procedure shows how to keep the game's electro-mechanical assemblies running efficiently.

  • Mirror Motor Adjustments: (Refer to Figure 1)
  • Turn off game power and separate the game halves.
  • Locate the mirror motor assembly in the top of the rear half. Rotate the screw axis (Fig. 1) to ensure it turns freely. The mirror should move up and down smoothly. If it does not, adjust the two screws (Fig. 1) holding the screw axis collar and/or adjust the bolt on the screw axis collar (Fig. 1) to tighten or loosen the ball bearing inside the collar. Keep the screw axis oiled lightly from time to time. Ensure that the mirror sensor disc (Fig.
  • turns freely between the mirror CP sensors (Fig. 1). If not, position the CP sensor bracket (Fig. 1) by loosening its

R ING BALL BEARING MIRROR MOTOR

MIRROR

“HIT” LED BOARD

COLLAR ADJUSTMENT: SCREWS

CP SENSOR BRACKET SCREW AXIS (MIRROR MOTOR) FIGURE 1

MIRROR CP SENSORS

CP SENSOR ADJUSTMENT SCREWS =

© screws (Fig. 1) and moving the bracket up/down, or left/right as necessary. The sensor disc should not scrape against any part of the opto-isolators. Adjust the 3 mirror sensors by rotating the mirror in its down position. Check the mirror sensor shutter (Fig. 1) to ensure its notch passes the down mirror limit sensor (Fig. 1). Follow the same procedure for the center (Fig.1) and up (Fig. 1) mirror sensors. If any are out of alignment, position the 3 sensors by loosening screws (Fig. 1) and moving the sensor brackets (Fig. 1) back and forth, left and right as needed. The mirror sensor shutter (Fig. 1) should move freely without touching the optoisolators. It may also be necessary to raise or lower the mirror sensor shutter stop (Fig. 1) with its two screws. This will help position the shutter, as needed.

  • Keep the motor ball bearing (Fig. 1) lightly oiled.

SENSOR ADJUSTMENT SCREWS

UP MIRKOK LIMIT SENSOR (BACK SIDE)

CENTER

(BACK SIDE)

DOWN MIRROR LIMIT SENSOR (BACK SIDE)

MIRROR SHUTTER STOP, BRACKETS

Page 19

FIGURE 2 MONITOR CENTER SENSOR

MONITOR SENSOR SHUTTER

LEFT CRT LIMIT SWITCH

MONITOR SCREW MONITOR ee AXIS ADJUSTMENT SCREWS

  • Monitor Mirror Adjustments:
  • Unlock and remove the service door located on the side of the rear game half. (See Figure 2.) Power should be off. Check the monitor sensor shutter (Fig. 2, 3) to ensure it is not bent. If necessary, remove it to straighten. Note that the monitor center sensor (Fig. 2) slides left and right along the monitor sensor shutter (Fig. 2). Be sure it moves freely without touching the shutter. If needed, move the shutter up/down, or left/right by loosening its screws (Fig.
  • to align. Also, the center sensor (Fig.
  • can be moved up or down by loosening its screws (Fig. 2). Inspect it to make sure it is not cracked. Check that the monitor assembly guide pin (Fig. 3) moves freely back and forth along the monitor screw axis (Fig. 3) and guide path (Fig. 3). The monitor screw axis collar (Fig. 3) must slide smoothly on the axis. It may =

a2

d) CENTER SENSOR

e ADJUSTMENT SCREWS

RIGHT CRT. LIMIT SWITCH

) MONITOR ce CP SENSOR

SENSORS ADJUSTMENT

‘SCREWS

MONITOR CRT (MONITOR) R SENSOR DISC MOTO!

need adjustment by loosening or tightening the ball bearing bolt (Fig. 3) on the collar. Keep the screw axis lightly oiled. As the monitor assembly moves left and right, it activates the CRT Limit switches to prevent it from moving too far. The left CRT Limit switch (Fig. 2) and the right Limit switch (Fig. 2) should be checked to ensure the monitor assembly activates them. If necessary, realign the switches by moving them left or right on their brackets. The monitor/mirror assembly fits into and pivots on the base (Fig. 3). Periodically check it to be sure it is oiled, and that the ball bearing inside it turns freely. Be sure the monitor sensor disc (Fig. 3) rotates between the monitor CP sensors (Fig. 3) easily and does not scrape the sides. If necessary, realign the monitor CP sensors (Fig. 3) with their screws (Fig. 2).

Page 20
  • To adjust the tension on the sprocket - Alignment of Mirror and Motor chain (Fig. 4), loosen the motor- During Self-Test Mode: mounting nuts (Fig. 4) slightly, and As was mentioned, the game displays a turn the tension bolt (Fig. 4) to loosen yellow “X” on the screen during the selfor tighten the sprocket chain. Do not test (See Maintenance). Also, the “hit” LED make the chain too loose or too tight. flashes on at this time to allow alignment of There should be a small amount of both mirror and monitor assemblies. If the slack in the chain, for best results. red LED does not line up with the “X”,

FIGURE 3

MONITOR CP SENSORS MONITOR SHUTTER MONITOR SENSOR DISC ADJUSTMENT CRT (MONITOR) MOTOR SCREWS Te

MONITOR = SENSOR SHUTTER

BALL _ SCREW MONITOR ASSEMBLY MONITOR GUIDE

BASE (BALL BEARING INSIDE)

  • Important Note: If the game is toberun _follow this procedure: on either a 50 HZ or 60 HZ line, the two a) If the “X” appears above the LED, admotor sprocket wheels must be checked just the mirror limit sensors (Fig. 1) by before operating the game. moving the sensor board upward slightly. Loosen the board’s screws (Fig. 1) to For 60 HZ line: Sprocket wheel at posi- slide the bracket up. The “X” and LED tion A (see Figure 4) must have 22 teeth. can also be matched up by sliding the The sprocket at position B (Fig. 4) must “hit” LED board (located between the have 20 teeth. laser beam boards—see Figure 1) up or For 50 HZ line: Reverse the down, as required. This board moves sprockets—20-teeth sprocket at A; up or down by loosening its mounting 22-teeth sprocket at B. screws.
Page 21
  • If the “X” appears to the left or right of the “hit” LED, adjust the position of the monitor sensor shutter (Fig. 2). Loosen its mounting screws (Fig. 2) and slide it left or right, as needed.
  • Finally, turn the steering handle left/right and up/down, and check that the “X” and LED are matched up again.

4. Steering Handle Adjustments:

  • Figure 5 shows the top view of the complete steering mechanism. Note the positions of the UP and DOWN switches. These are activated by the guide pin when it slides against the switch actuators. The guide pin should be mechanism is not activated. If it is not, loosen the guide pin collar (see Figure 6) and slide it up or down the steering shaft to realign it. Figure 6 shows the inside view of the steering assembly. The LEFT and RIGHT switches are normally closed until deactivated by the CAM, as shown. Adjust the right/left switches for proper operation by the CAM. Two rubber rollers limit the left/right direction of the steering handle.
  • To replace the “fire” switch in the steering handle, simply unscrew the setscrew on the side of the switch and lift out the switch, Solder the switch leads to the new switch. Push it into place b)

centered in the slot when the and retighten the set-screw.

FIGURE 4

CRT (MONITOR) MOTOR =

es

‘4

ad

ORS)

la |

SPROCKET B MOTOR TENSION, CHAIN

MOUNTING BOLT

NUTS

Page 22

FIGURE 5

GUIDE PIN

UP SWITCH

  • Monitor Removal Instructions: Should it be necessary to remove the game monitor, follow the following procedure:
  • Unplug the game from the wall outlet.
  • Separate the game halves.
  • Remove the bolts holding the screen graphics assembly (see Figure 7) on both sides of the monitor.
  • Disconnect the monitor harnesses at the bottom of the monitor. Take out the monitor mounting bolts (Fig. 8). SWITCH ACTUATORS

DOWN SWITCH

  • Then, remove the monitor. DO NOT BUMP THE MONITOR AGAINST THE FRAME!
  • CAUTION: When replacing the color monitor, gently set the monitor on its mounting brackets! The neck of the monitor tube could be damaged if it hits the lower framel
  • Bolt the monitor back in place, and reattach the screen graphics assembly.
  • Then, reconnect the monitor harnesses at the bottom of the monitor, Make sure they are connected SECURELY.
Page 23
  • Miscellaneous Adjustments:
  • Inside the coin-entry door, on the upper edge, is a Control Block, as shown. @ (Ca [__-VOLUME: ‘d (i UPPER The functions of these controls are: CKO (om.

f VOLUME:

SWITCH SERVICE DEMAGNETIZING SWITCH SWITCH

Demagnetizing Switch: Pushing this switch clears any color distortion on the color monitor. Self-Test Switch: This activates the game self-test feature. Service Switch: This credits a game without advancing the coin counter. Volume Controls: One control for each speaker, upper and lower.

FIGURE 6

LEFT SWITCH RUBBER RIGHT SWITCH ROLLERS

GUIDE PIN COLLAR

Page 24

FIGURE 7

GRAPHIC ASSEMBLY MOUNTING BOLTS (Both sides of monitor)

SCREEN GRAPHICS ASSEMBLY

  • Voltage Conversion Instructions: Then, wire the game transformer to match the selected voltage wiring
  • Unplug the game from the wall diagram below. Be sure to make outlet! good solder connections when reii) Refer to the chart below to select the wiring. Check the wiring before turproper line voltage for the game. ning on the game!

TRANSFORMER CONNECTION 2zov 200v z20V 230V

°iy[)to°to°
© 100100O 100© 100
O10oO110Hofare)
120]© 120)© 120O 120
°°°°
0 100100© 100O 100
O10oO 110110O110
120Oo 120O 120120
Page 25

iii) DO NOT change any wiring to the color monitor! iv) If the new line voltage is at 50 HZ, and the game originally ran on a 60 HZ line (or vice versa), the monitor motor sprockets must be changed. See section 2i, under “Monitor Motor Adjustments” for instructions.

FIGURE 8

MONITOR MOUNTING BOLTS (3 on each side)

CAUTION: SET MONITOR DOWN GENTLY WHEN REPLACING!
Page 26
  • Game Option Selection: Refer to the chart below to select the desired game options.

Switch 1 OPTION 1COIN _1PLAY 1 PLAY 1 PLAY 2 PLAYS 3 PLAYS 4 PLAYS 6 PLAYS 1 PLAY 2 COINS 1 PLAY 4 COINS _1 PLAY 1 COIN 2 PLAYS LCOIN 3 PLAYS 1 COIN__4 PLAYS 1 COIN __6 PLAYS NO HIGH SCORE INITIAL ENTRY HIGH SCORE INITIAL ENTRY. off [ADVERTISING SOUND OFF on{ADVERTISING SOUND ON COIN MECH. 2

COIN MECH. 1

Switch 2 OPTION GAME STARTS WITH 4 BARRIERS GAME STARTS WITH 6 BARRIERS 1 BONUS BARRIER—if you hit all invaders and saucer (UFO) 2 BONUS BARRIERS EXTENDED PLAY — bases return if you hit credit switch when 1 base remains (must have at least 2 credits on) NO EXTENDED PLAY

NOT USED

97209-P LOGIC BOARD

OFF

ON SWITCH 1

&) SWITCH 2

Page 27

= parts section

Page 28

Rear Cabinet Assembly

ITEM # _ DESCRIPTIONSEGA #_GREMLIN #
1Leg Adjuster (2)M-163-4601-0455
2Lock Tongue (Service Door)PB-1022601-0587
3Service DoorT4111601-0588
4Ornament Edging (Cabinet Trim)TI-1109-B601-0589
5Air Vent (2)PT-0342601-0097
6Ultraviolet Lamp Tube (2)$-92035390-0045
7Shipping BracketSGB-2517105-0161
8Graphics, UpperTI-1118420-0546
9Graphics, FrontTL1119420-0548
10Graphics, BackTI-1120420-0547
nCaster Wheels, (2)S-81159601-0391
12Line FilterS-96634601-0429
13Power Switch$-90834509-0039
14Outlet, AC Type$-91449601-0484
Page 29

Front Cabinet Assembly

ITEM #DESCRIPTIONSEGA #_GREMLIN #
1Window Graphics, Right (Page 26)TI-1082420-0544
2Window Graphics, Left (Page 26)TI-1083 = 420-0545
3Front WindowTI-1051253-0207
4Back Window (Hood)TI-1050252-0131
5Back Window RodTI-1077601-0590
6Ornament BossTI-1078129-0009
7Speaker, 16cm, 8 ohm (2)S-96965130-0018
8Upper Speaker Guard PlateTI-1062105-0222
9Upper Speaker NetTI-1061601-0596
10Lower Speaker Guard PlateTI-1056 = 117-0131
11Lower Speaker NetTI-1055601-0558
12Floor MatTI-1052320-0043
13Edge Protector (2)TI-1053601-0599
14Hold Bracket (Back Window)TI-1057105-0223
15Ornament Frame, LowerTI-1058601-0598
16Ornament Frame, UpperTI-1059601-0597
17Hold Bracket (Front Window)TI-1063105-0221
18Cabinet Handles (2)TI-1076109-0041
19Ultraviolet Lamp TubeS-91058390-0038
20Leg AdjusterM-163-4601-0455
  • 7 8X9 5 4

12)

2B,

10X11 14)

15,

Page 30

8 ®&

Front Cabinet Assembly, Continued

--Front Panel--

21Door Lock (For Cash Box Door, ServiceLS-1064 — 220-0097

Door, Back Door, and Coin Entry Door)

22Lock TongueSH-1044601-0066
23Lock Retainer BracketTI-1080105-0220
24Cash Box DoorTI-1064601-0595
25Cash Box (Not Shown—Behind Box Door)TI-1065220-0162
26Cash Box Door Frame, UpperTI-1066601-0594
Not Shown Cash Box Door Frame, LowerTI-1067601-0593
27Cash Box Door Frame, RightTI-1068601-0592
28Cash Box Door Frame, LeftTI-1069601-0591
Page 31

Front Cabinet Assembly, Continued

ITEM #DESCRIPTIONSEGA # GREMLIN #
29Strategy Instruction Plate, EnglishTI-1085117-0129 ai

Strategy Instruction Plate, Japanese TI-1084. 0 --------

30Play Instruction Plate, EnglishTI-1232117-0131
Play Instruction Plate, JapaneseTI-1230-J
31Coin Entry DoorTI-1218601-0586
32Coin Entry Door CoverTI-1219601-0585
33,Lock Tongue (Coin Door Lock—NotTI-1231601-0584

Shown) Not Shown Coin Entry Bracket A DH-1045 105-0219

Not Shown Coin Entry Bracket BDH-1046105-0218
34Reject Cup W/Flap DoorAH-1062601-0416
35Reject Button Assembly (2)MP-1017 240-0097
Not Shown Reject Lever Spring (2)OL-3018125-0091
36Coin Entry Plate, USATI-1223117-0140

Coin Entry Plate, Japan TI-422200

37Credit SwitchS-97228509-0125
Not Shown Switch Lamp (6V)S-97230390-0090
Not Shown Coin Mechanism, USA.-—----800-0103
Coin Mechanism, JapaneseCC-2006220-0084
Not Shown Volume Control, 25k ohm (2)S-93157220-0111
(All areVolume Control Knob (2)S-90595601-0042
locatedDemagnetizing SwitchS-96397240-0105
insideButton-Demagnetizing SwitchS-96400240-0106
coinService SwitchS-96405509-0111
door)Self-Test SwitchS-93640509-0057

--Front Panel Switches, Displays~

38Barrier Switch, YellowS-97229509-0121
39Base Switch, Red (5)S-97227509-0123
40Base Switches PlateTI-1418 = 117-0146
Not Shown Switch Bracket, Base SwitchesTI-1417105-0224
Not Shown Bar-Graph LED (Red, Rectangular;S-97231390-0086

for Credit, Barrier and Round Displays)

41Decal, MeterTI-1407420-0566
42Mask, Credit (Clear Red Plastic)TI-1411601-0572
43Mask, ScoreTI-1410601-0571
44Mask, RoundTI-1409601-0570
45Mask, BarrierTI-1408601-0568
46Credit Display Plate, (Clear Plastic)TI-1405117-0139
47Score Display PlateTI-1404117-0138
48Round Display PlateTI-1403117-0137
49Barrier Display PlateTI-1402117-0136
Not Shown 7-Segment Readout (Score Display)S-96601481-0071
Not Shown Switch Lamps (6V)S-97230390-0090
50Front PanelTI-1401601-0569
Page 32

Monitor, Motor and Frame Assembly

ITEM #__DESCRIPTIONSEGA #GREMLIN #}
1Monitor Sensor ShutterTI-3068117-0134
2Holder PlateTI-3070117-0145
3TV Mask (Plexi)TI-3078601-0563
4TV Mask (Black Paper)TI-3082601-0566
5TV Graphics A (Dome)TI-3079420-0554
6TV Graphics B (Strip)TI-3080420-0555
7Graphics Bracket (2)TI-3081105-0225
8TV Mounting Bracket (2)TI-3085105-0214
9*Color Monitor, 15” (16 Type)96887-P601-0562
10Pivot HousingTI-3009252-0134
11Screw Axis (Monitor)TI-3011280-0338
12Guide PinTI-3012280-0339
13Sensor DiscTI-3014106-0057
14FlangeTI-3074280-0337
15Guide Bracket (2)TI-3017105-0213
16Lead Plate (2, Nylon)TI-3018117-0135
17Switch Bracket, ATI-3019105-0212
18Switch Bracket, BTI-3020105-0211
19Monitor CP Sensor Board, CTI-3083601-0567
{20Collar (Monitor Screw Axis)HT-3045250-0465
Page 33

Monitor, Motor and Base Assembly, Continued

[ITEM # __ DESCRIPTIONSEGA #GREMLIN #
21Sprocket Wheel (20 teeth)TI-3075350-0174
22,Sprocket Wheel (22 teeth)TI-3076350-0176
23Chain (45 links)TI-3077280-0336
24CouplerTI-3086280-0351
25Compression SpringTI-3087125-0098
26Ball Bearing (2)S-82387100-0011
27Ball (For Screw Axis Collar)S-80042101-0010
28Ball (For Pivot Housing)S-80674101-0009
29Monitor Right, Left Limit SwitchS-91421509-0048
30Monitor MotorS-97226350-0172
Not Shown Sensor (Opto-Isolator for SensorS-97086601-0582

Boards A, B, C, D)

*The color monitor contains a 15” color tube. This is the same size as “Color Display 16 Type”. BD) D2

Page 34

Mirror, Motor and Frame Assembly

ITEM # _ DESCRIPTIONSEGA #GREMLIN 4
TMirror Motor (Page 31)S-97226350-0172
2Universal Joint (Page 31)TI-3076350-0173
3Spindle ShaftTI-3064123-0060
4Ball BearingS-82597100-0014
5Bearing HousingTI-3030250-0464
6Collar BracketTI-3060252-0133
7Steel Ball (Inside Collar)S-80021101-0008
8Collar (Mirror Screw Axis)TI-3059601-0576
9Shoulder ScrewTI-3061280-0352
10Half MirrorTI-3056275-0072
11Mirror Frame, UpperTI-3055601-0578
12Mirror Frame, LowerTI-2054601-0579
13Mirror Frame, RightTI-3053601-0580
14Mirror Frame, LeftTI-3052601-0581
15Sensor DiscTI-3073106-0056
16Screw Axis (Mirror)TI-3033X.280-0335
17Motor BracketTI-3031105-0209
18Motor Mounting BracketTI-3029105-0210
19Pivot (Fits Inside Base)TI-3028280-0349
20Monitor Center Sensor Board, ATI-3022X.601-0565
Page 35

Mirror, Motor and Frame Assembly

ITEM;

DESCRIPTIONSEGA #GREMLIN #
Flange (Behind Sensor Disc)TI-3015280-0350
Mirror Limit Sensor Board, BTI-3038X601-0561
Lead Plate A (Nylon)TI-3040117-0144
Lead Plate B (Nylon)TI-3041117-0143
Mirror Sensor ShutterTI-3042117-0132

Extension Spring (For Mirror Sensor

Shutter)TI-3044125-0095,
TV Mounting Bracket (2)TI-3045105-0207
Mirror Holder (2)TI-3046109-0039
Shoulder Screw (2--For Mirror Holder)TI-3047280-0347
Spring HookTI-3048280-0346
Sensor Board A, BracketTI-3049X105-0206
Lead Roller (Wheel)MP-2025121-0007
Mirror CP Sensor Board, DTI-3084601-0564
Extension Spring (Mirror)TI-3071125-0096

Sensor (Opto-Isolator) For Sensor

Boards A,B,C,DS-97086601-0582
Page 36

LED Laser Beam Assembly

ITEM #DESCRIPTIONSEGA #GREMLIN
1LED Board, RightTI-1303171-0029
2LED Board, LeftTI-1302171-0030
Green LED, LargeS-96903390-0093
Green LED, SmallS-96901390-0095
Resistor ArrayS-96900601-0583
3“HIT” LED BracketTI-1306105-0217
4“HIT” HolderTI-1308109-0040
5“HIT’LED, RedS-97225390-0085
6Screen (2)TI-1304601-0559
Page 37

Power Supply Asembly

ITEM # _ DESCRIPTIONSEGA #GREMLIN #
1Switching RegulatorS-96560601-0158

2SC2335 Transistor 482-0084 uPC 1042 IC 316-0706 TL 494 IC 312-0222

2Power Transformer97239560-0057
3Power Amplifier (2)97084-P110-0018
TA 7216PS-97072313-0043
4Regulator UnitTI-4007601-0573
7812 ICS-96436313-0014
7805 ICS-94267313-0012
5Fuse, 2A (2)S-90644514-0032
Fuse, 6A.S-90639514-0031
Fuse, 8A (For 120 Volt Use)S-91151514-0043
Fuse, SA (For 220 Volt Use)S-90661514-0034
Page 38

P| © Q 2 \_Le

23 16

Steering Handle Assembly

ITEM ¢___ DESCRIPTIONSEGA #__GREMLIN #
1CamTI-2040X350-0175
2Handle Bracket, RearTI-2029105-0201
3Upper BracketTI-2039105-0202
4Switch, (For Left/Right)$-91421509-0048
5Rubber Ring, ATI-2021320-0041
6Handle ShaftTI-2030123-0059
7Bearing, Mini Pillow$-82465100-0013
8Stopper BracketTI-2036105-0203
9CollarTI-2032601-0560
10Compression SpringTI-2035125-0093
uGuide Pin CollarTI-2033,129-0007
12Rubber Ring, BTI-2022320-0042
13Handle Bracket, FrontTI-2028105-0204
14Guide PinTI-2034280-0333
15HandleTI-2017109-0037
Not Shown Wire Cover (On Back of Handle)TI-2025280-0334
16Emblem, SegaTIL-2019420-0553
7Supporting BracketTI-2038105-0205
Page 39

Steering Handle Assembly, Continued

18Rubber RollerTI-2020121-0015
19Extension SpringTI-2024125-0094
20ActuatorTI-2027104-0006
21Switch (Up/Down)S-91344509-0118
22,Switch, Push Button, Red (Fire)S-97452509-0120
23HousingTI-2031250-0463
24Handle BossTI-2018129-0008
25Button Plate (For Fire Switch)TI-2043117-0142
26Switch Holder (For Fire Switch)TI-2042109-0038
27Compression SpringTI-2026125-0097

Logic Board Assembly, PT.# 171-0028 (97209-P)

LOCATIONDESCRIPTIONSEGA #GREMLIN #¢
DIAC 1,2,3,4 DIAC, 2A (4)S-93237601-0574
4 TRIAC, 400V, 3A (4)S-97467482-0039
Crystal, 15.46848 MHZS-95875203-0009
PC1, 2, 3,4Photo CouplerS-94928280-0140
TR16,17,18,19 Transistor, 2SB765K or TIP 125S-96677482-0019
1C132PR-67 PromS-94080-67 312-0211
1C123PR-66 PromS-95843-66312-0212
1C118PR-65 PromS-95843-65312-0213
IC86PR-54 PromS-95775-54312-0214
IC14675365 ICS-97217314-0132
1C1062147 or P2141-4 ICS-97216314-0133
1C152,156AM 91L11APCS-94984315-0018
1C142uPB 8228DS-96274314-0134
1C95, 114,TD 62003PS-96678312-0106

119,125,

RA11,12,13,Resistor Array, 33 ohmX8, %WS-97219460-0046
RA8,9,15Resistor Array, 220 ohmX8, %4WS-95706312-0116
RA3,5Resistor Array, 560 ohmX8, %W.S-95688460-0047
RA1,2,4,6,Resistor Array, 1k ohmX8, %W.S95686601-0237

16,18

RAI7Resistor Array, 4.7k ohmX8, %WS-95705460-0048
TR20, 21,22,2SC458C TransistorS-92415482-0043
coresBus Bar97329X601-0575
IC158Eprom 0312-0215
IC157Eprom 1312-0216
1C154Eprom 2312-0217
1C153Eprom 3312-0218
1C150Eprom 4312-0219
1c149Eprom 5312-0220
1C136Eprom 217312-0221
Page 40

Sound Board Assembly, PT.# 116-0009 (97211-P)

LOCATIONDESCRIPTIONSEGA #_GREMLIN #
1C7MN 3101 IC$-96514313-0040
IcéMN 3005 ICS-96513313-0041
1C2,3,11MB 4391 M ICS-96675312-0209
1C4,5AN 6551 ICS-96837313-0042
IC1294560 AN ICS-96464312-0147
1C1376477S-96504312-0150
Ic1LM 324S-95783313-0034

QUANTITY

DESCRIPTIONSEGA #__GREMLIN # PER 5 GAMES

LOGIC BOARD-

DIAC, 2A$-93237601-05745
TRIAC, 400V, 3AS-97467482-00395
Crystal, 15.46848 MHZS-95875230-00092
Photo CouplerS-94928280-01402
Transistor, 2SB765K or TIP125S-96677482-00192
75365 IC$-97217314-01322
2147 or P2141-4 ICS-97216314-01333
AM 91L11APCS-94984315-00183
uPB 8228D$-96274314-01342
TC 62003PS-96678312-01062
2SC458C TransistorS-92415482-00432
Eprom 0312-02151
Eprom 1312-02161
Eprom 2312-02171
Eprom 3312-02181
Eprom 4312-02191
Eprom 5312-02201
Eprom 2170enennene312-02211

--SOUND BOARD--

MN 3101 ICS-96514313-00402
MN 3005 ICS-96513313-00412
MB 4391 MICS-96675312-02092
AN 6551 ICS-96837313-00422
94560 AN ICS-96464312-01472
76477S-96504312-01502
LM 324S-95783313-00343
Page 41

Recommended Spare Parts, Continued

DESCRIPTION SEGA # QUANTITY | GREMLIN # PER 5 GAMES

--LASER BEAM ASSEMBLY--

Green LED, Large Green LED, Small “HIT” LED, Red S-96903 S-96901 S-97225 390-0093 10 390-0095 10 390-0085 5

--MIRROR, MOTOR AND FRAME ASSEMBLY--

Mirror Motor Steel Ball (Inside Collar) Shoulder Screw Half Mirror Sensor Disc Screw Axis (Mirror) Monitor Center Sensor Board, A Sensor (Opto-Isolator) For Sensor Boards A, B, C, D

Leg Adjustor Ultraviolet Lamp Tube

--FRONT CABINET-- Window Graphics, Right Window Graphics, Left Front Window Back Window (Hood) Back Window Rod Speaker, 16cm, 8 ohm

Door Lock Cash Box Reject Cup W/Flap Door Credit Switch Switch Lamp, 6V Coin Mechanism, USA Coin Mechanism, Japanese S-97226 S-80021 TI-3061 TI-3055 TI-3073 TI-3033X TI-3022X

S-97086

--REAR CABINET-- M-163-4 S-92035

TI-1082 TI-1083 TI-1051 TI-1050 ‘TI-1077 S-96965

--FRONT PANEL-- LS-1064 TI-1065 AH-1062 S-97228 S-97230

CC-2006 350-0172 101-0008 280-0352 601-0578 106-0056 280-0335 601-0565 aARPNuUane

601-0582 25

601-0455 4 390-0045 2

420-0544 420-0545 253-0207 252-0131 601-0590 130-0018 Pee Ee

220-0097 220-0162 601-0416 509-0125 390-0090 800-0103 220-0084 RENOWNED

Page 42

Recommended Spare Parts, Continued

DESCRIPTION SEGA # GREMLIN ¢ QUANG TY MES | --FRONT PANEL SWITCHES, DISPLAYS-- Barrier Switch, Yellow Base Switch, Red Bar-Graph LED 7-Segment Readout Front Panel

Cam Switch (For Left/Rignt) Rubber Ring, A Rubber Ring, B Handle Actuator Switch (Up/Down) Switch, Push Button Red (Fire) Button Plate (For Fire Switch) Switch Holder (For Fire Switch)

Color Monitor, 15” Screw Axis (Monitor) Sensor Disc Monitor CP Sensor Board, C Sprocket Wheel (20 teeth) Sprocket Wheel (22 teeth) Chain (45 links) Ball (For Screw Axis Collar)

Switching Regulator 2SC2335 Transistor uPC 1042 IC Power Amplifier TA 7216P 7812 IC 7805 IC Fuse, 2A Fuse, 6A Fuse, 8A (For 120 Volt Use) Fuse, SA (For 220 Volt Use) TL 494 IC S-97229 509-0121 S-97227 509-0123 S-97231 390-0086 S-96601 481-0071 TI-1401 601-0569

--STEERING HANDLE ASSEMBLY-- TI-2040X 350-0175 S-91421 509-0048 TI-2021 320-0041 TI-2022 320-0042 TI-2017 109-0037 TI-2027 104-0006 S-91344 509-0118 S-97452 509-0120 TI-2043 117-0142 TI-2042 109-0038

--MONITOR, MOTOR AND BASE ASSEMBLY-- 96887-P 601-0562 TI-3011 280-0338 TI-3014 106-0057 TI-3083 601-0567 TI-3075 350-0174 TI-3076 350-0176 TI-3077 280-0336 S-80042 101-0010

--POWER SUPPLY-- S-96560 601-0158 482-0084 316-0706 97084-P 110-0018 S-97072 313-0043 S-96436 313-0014 S-94267 313-0012 S-90644 514-0032 S-90639 514-0031 S-91151 514-0043 S-90661 514-0034 ~ 312-0222 WwWUNWHNNNN HoRwN

BREE ENB

Page 43

schematics table of contents

Game Block Diagram, Cabinet Wiring 0.0.0.0. 0.0. c ccc cc e eee eee CPU oo. cc Video Ram Page B/Video Ram Page D . Video Ram Page E/Video Ram Page F............... Power Connections, Video Ram Page Counters/Eprom ........ Video Generation, Input Buffers, Dip Switch $1/Scoring Displays . Master Clock: Timing Circuit ........0 0.00 c cece cece ee eee Player Controls: Steering, Photo Sensors, Motor Drive . . Player Controls: Front Panel Switches/LED Fire Beam Oscillator: UFO Hit Sound, Invader Sound .........00 0.0 ccc cece eee Jy Oscillator: UFO Hit Sound, Invader Sound, Player Fire Sound ae Oscillator: Bomb Sound, Warning Sound . . Oscillator: Bucket Brigade Device (BBD) Ampli ~ZOmmModOw>

+ Circuit, Power Connections .........0 00.0 cece ccc n nen teen e nee M Oscillator: Explosion Sound, Rocket Sound, Word (Character) Sound, Front-Back BBD Main Amplifier ..........0.00 0000s c eeu N Switching Regulator ........ 00.00. c ccc ccc nee oO

Page 44

> iJ TTT “i asi Th

Heal Wl it

tu, WIRE COLOR CODE

REDcBROWN
BLUEDPURPLE

YELLOW | E LIGHT GREEN :

GREEN|JJUMPER WIRE
WHITELLARGE WIREte

MAROON | K_ KING WIRE (30 str.)| ts ORANGE i BLACK — | EXAMPLES

GRAY 52 WHITE BLUE

PINK51WHITE RED

SKY BLUE| 50 WHITE BPOSVOUSENE

VOLTAGE | 120V__| 200 v | 220 v | 230 V ‘STAND-BY | w. w [ww MAXIMUM] 2A, 190w|w fw [w

ABBREVIATIONS USED. SOL. SOLENOID sw. SWITCH RE. RELAY

SWITCH SYMBOLS, Circle in the Switch @ Symbols indicate Operation by a motor

ty Make and Break Switch

GAME BLOCK DIAGRAM, CABINET WIRING + Normally Closed

+ Normally Open

Page 45

GAME BLOCK DIAGRAM,

CABINET WIRING

Page 46

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 47

VIDEO RAM PAGE D VIDEO RAM PAGE B

Page 48

VIDEO RAM PAGE E

ae oat 3 5

VIDEO RAM PAGE F

Page 49

EEE

POWER CONNECTIONS, J

VIDEO RAM PAGE COUNTERS PEEREE

Page 50

|i POWER CONNECTIONS, o 1 VIDEO RAM PAGE COUNTERS ake 7 OP

Page 51

ae

IDIP SWITCH #1 VIDEO GENERATION, INPUT BUFFERS,

ute eFlaween inp x

Page 52

SESE:

gz

MASTER CLO: TIMING CIRCUIT

G

Page 53

PLAYER CONTROLS: STEERING, PHOTO SENSORS, MOTOR DRIVE yee

le rear

Le cha Ile a ay ||

Ve erga) gg L. if eens te ate leo fr] cer eget euler aby oy

Baty

ae ay Le: Heeb tig | +] p—| Ts a L

Page 54

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 55

VEO WIT soUND

oor | wv, sound

ne43al wy BeBD ik AAPA

Wu scun out os TP

a

‘rom 2 (36)

We OSCILLATOR: UFO HIT SOUND, INVADER SOUND J |

Page 56

INVADER SOl , OSCILLATOR:|UFO HIT SOUND, K PLAYER FIRE SOUND

Page 57

ics e429) foo eee

ILLATOR: BOMB SOUND, WARNING SIGNAL L

, OSC!

Page 58

ww osslh fH forty An OY,

FRONT Mix AMP a

mw's101

OSCILLATOR: BUCKET BRIGADE DEVICE (BBD) AMPLIFIER

CIRCUIT, POWER CONNECTIONS

Page 59

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 60

OD TLSA sc

ACAOV SOV 0.097] lal

TLSA sc ‘iu +5V-6A

+ isae7ic — S2471q T LY |} +

Ves Our Me GC E, Bj 7 82kS == 0.027

cT RT aD OG

Rve.2EBL 1s2471C,

SWITCHING REGULATOR QO