CATHODE RAY TOMES

VS UniSystem Kit DK Popeye Mario

VS. UniSystem Kit (Donkey Kong, Donkey Kong Jr., Mario Bros., Donkey Kong 3, Popeye) (Nintendo, 1985) · Manual · 55 pages · 30 sections · original scan

Page 1

VS. UniSystem€

KIT MANUAL

G

FOR INSTALLATION IN

©1985 Nintendo’of America Inc. *© 1982 King Feature Syndicate

Page 2
WARNING If the replacement parts and components in this VS. UniSystem™ kit are not installed exactly as instructed herein, there may be radio frequency interference created in violation of F.C.C. class A standards.
WARNING This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a class A computing device pursuant to subpart J of part 15 of F.C.C. rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference; in which case, the user at his own expense will be required to take whatever measures may be required to correct the interference.
WARNING Use of non-Nintendo parts or modifications to your VS. UniSystem™ parts and components may adversely affect the safety of your game, and may cause injury to your players.
Page 3

Vil.

Vill.

Xi. TABLE OF CONTENTS

Introduction

Contents of VS. UniSystem™ kit

List of Tools Needed

Replacement Process Step-by-Step

Final Check Sheet and Adjustments

Wiring Diagram

Service Bulletins

CPU PC., Power Supply and Monitor Schematics

Reorder Parts List 5-18

INSERT

23-29

INSERT

30-41

Page 4
  • INTRODUCTION

VS. UniSystem™ kit

VS. UniSystem™ kit enables you to change Donkey Kong", Donkey Kong Jr.*, Mario Bros.*, Donkey Kong 3*, and Popeye** into a VS. UniSystem” in less than one hour. A VS. UniSystem* will use any non-interactive VS.-Pak*.

Before you begin, be sure you are properly prepared. Make certain you have selected the proper VS. UniSystem* kit for the particular game you are replacing. Next thoroughly read this instruction manual to familiarize yourself with the proper procedures. Make certain that you have all the tools necessary to complete the process.

If you have any questions, please call Nintendo Service at 1- (800)- 633-3236.

NOTE: This VS. UniSystem” kit is not usable on an original wide-body (700W) Mario Bros. game.
  • Donkey Kong, Donkey Kong Jr., Mario Bros., Donkey Kong 3, and VS. UniSystem are trademarks of Nintendo of America Inc. ** A trademark of King Features Syndicate, Inc.
Page 5

Il. Contents of VS. UniSystem kit

Parts Name Quantity Remarks

MDS-CPU PC. Board Assembly MGS-UP Operation Panel Assembly MGS-UP Front Screen (600W) Assembly MGS-UP Side Decal VS. UniSystem™ Manual 062 Shield Cover Complete Assembly 072-36P Edge Connector Harness 072-44P Edge Connector Harness Assembly MGS Serial Number Plate Flat Cable Tie Wood Screw 3.1 x 10 FCC Class-A Label FBI Sticker Following parts are for TKG, DJR, DKC, TMA only 054 Shield Cage Video Monitor Bracket (L) Video Monitor Bracket (R) Video Monitor Support Bar Blind Cardboard (large) Carriage Bolt 6 x 30 Cap Nut M6 Cap Nut M5 Machine Screw 5 x 12 Wood Screw 3.5 x 13 Ground Wire (E) Hole Template Following parts are for TPP only Power Supply and Transformer Assembly Fuse Set Bao paen nnn pani

AA ORRDHDANAAA without EPROMS and PPU with harness

821B-7B Power Assembly

Page 6

Ill. List of Tools Needed

Flat (standard) screwdriver

Phillips screwdriver 7mm nut driver

8mm nut driver

10mm nut driver

Ws" or 6.5mm drill bit

Electric reversing drill

Phillips bit (for drill)

Staple gun Paper stapler

Lacquer thinner Denatured alcohol or other cleaner

Large wire cutter

Note: Many steps require the use of a phillips screwdriver and having a phillips screwdriver bit for your drill will greatly speed up these steps.
Page 7

IV. Step-by-step instructions

  • Remove marquee/header (see illustration 1-1) A. Remove four (4) top trim screws B. Remove marquee plexiglass C. Replace marquee/header with new VS-Pak header D. Replace top trim and four (4) top trim screws
  • Remove old control panel and front screen (see illustration 1-2) A. Undo control panel holddown clamps B. Disconnect harness and remove control panel C. Remove front screen by sliding back front screen clamp (access from back door)
Page 8
Note: For Donkey Kong, Donkey Kong Jr. ONLY
  • Remove instruction label (see illustration 1-3)

A. B. c. Spray label with lacquer thinner Wait 15 minutes and remove with putty knife Clean area with cloth and lacquer thinner

Note: For Donkey Kong, Donkey Kong Jr. and Donkey Kong 3 ONLY

4, Remove monitor

moom> Unplug monitor connections and undo wire ties Remove blind cardboard on monitor only Remove monitor, upper monitor support bar and all carriage bolts (see illustration 1-4) Remove old side decal

IMPORTANT! Disconnect monitor ground wire at location shown in illustration (see illustration 1-5)
Page 9
Note: For Donkey Kong, Donkey Kong Jr. and Donkey Kong 3 only.
  • Side panels should have five (5) holes each. If your game has only two (2) holes, use template provided in kit and drill three (3) 1/4-inch or (3) 6.5-mm holes where indicated (see illustration 1-6).
Note: This step is for all games
  • With old side decals removed, clean side panel with alcohol and install new VS. UniSystem decals. Decals are placed parallel to top and back of game 2” from edge. (See illustration 17) See decal application sheet on page 18
Page 10
Note: These steps are for Donkey Kong, Donkey Kong Jr. and Donkey Kong 3 ONLY.
  • Install side support bars on monitor (see illustration 1-8)

A. Install new horizontal monitor mounting brackets to side panel with flange toward front of cabinet and pointing up. Note: use carriage bolt as shown (see illustration 1-9 & 1-10) Install monitor in horizontal position Monitor is placed on top of side bracket supports .

IMPORTANT! Reconnect the monitor ground wire (disconnected in step 4E) to carriage bolt shown (see illustration 1-10) poe
Page 11
Note: For Donkey Kong, Donkey Kong Jr. and Donkey Kong 3 ONLY
  • Install new blind cardboard (see illustration 1-11)

A. Remove adhesive backing on tape. Center blind cardboard on monitor and adhere. Place staple on top.

Top

NOTE: For Donkey Kong and Donkey Kong Jr. ONLY
  • Remove old PC. Board set and mounting brackets and old wire harness (see illustration 1-13) . A. If P.C. Board’ wood shelf has slots made from square stock wood, remove these (see illustration 1-12) B. Remove old Main Wire Harness
Page 12
NOTE: For Mario Bros. and Donkey Kong 3 ONLY
  • Remove old Shield cage assembly including Shield cover and old P.C. Board set
NOTE: For Donkey Kong, Donkey Kong Jr., Mario Bros. and Donkey Kong 3 ONLY.
  • Install new Shield cage so it is flush with rear of wood shelf and fasten with six (6) screws provided. IMPORTANT! On lower left corner install ground harness and connect the other end to the mounting bolt on the power supply as shown (see illustration 1-15 & 1-16)
Page 13

These steps are for Popeye ONLY

  • If you are replacing a Popeye game, remove old power supply transformer assembly (see illustration 2-1 & 2-2) Disconnect connector from switch plate Diconnect both plugs for monitor and lamp Disconnect ground harness connections Disconnect both power harness connections Remove four (4) wing nuts and take out old power supply Replace with new power supply assembly and tighten wing nuts
NOTE: Bolts for wing nuts may push through bottom of game during mounting of new power supply unit. If this happens, simply push them back up when power supply assembly is in place. G. Reconnect Steps A, B, & C being careful to get a good connection on Step C. Ground harnesses. mmpop>

"1

Page 14

These steps are for Popeye ONLY

  • Change fuse to 5 AMP and change label to 5 AMP on switch plate (see illustration 2-3)
  • Remove old P.C. Board assembly and old Main Wire Harness (see illustration 2-4) A. Remove the six (6) machine screws that hold on the Shield cover.
IMPORTANT: Save these machine screws

Remove Shield cover and complete P.C. Board assembly. Remove old Main Wiring Harness.

Page 15
IMPORTANT!! This step is for Popeye ONLY
  • Modify new Shield Cover Assy to fit old Shield Cage (see illustration 2-5)

A. Cut off six Fasteners on perimeter of Shield Cover Assy B. To install Shield Cover use six (6)machine screws from step 14A.

NOTE: This step is for all games
  • Install new MDS PC. Board and shield cover assembly (see illustration 4-1)

A. Attach short harnesses to P.C. Board with 36 pin connector on top B. Slide P.C. Board into Shield cage grooves C. Do not fasten Shield cover until after final check sheet and adjustments Section V is completed

Page 16
NOTE: These steps are for all games
  • Connection of Harnesses (see illustration 4-2)

A. Connect Coin, Service. Counter harnesses to 44P072 Edge harness.

Note: Harnesses are different for Popeye type and Donkey Kong or Donkey Kong Jr. type (see illustration 4-3) Fasten Control Harness 072-36P to wire tie approximately 5” from connectors. Route Harnesses through existing wire ties Connect Sound and Video Harness from monitor to Edge Connector Harness E. Connect Power Harness to Power Supply (9 pin connector) and fasten Power Harnesses to Shield Cage with cable tie. F. Connect 44P Edge Connector Harness and 36P Edge Connector Harness to Cover Assy.

Donkey Kong type connectors

Popeye type connectors

Donkey Kong Donkey Kong Jr. type connectors

Page 17
Note: Select proper connector for game you are changing SERVICE (2 wires)

44P072 Edge Connector Harness Assy

COIN (4 wires)

SERVICE (pin)

Popeye type connector COUNTER AUDIO (2pin) B pin) (4 pin) Donkey Kong 36P072 Edge Connector Harness Donkey Kong Jr. type connector

(12 pin)

To Control Panel

(15 pin)

Note: These steps are for all games
  • Install new front screen and fasten with front screen clamp (see illustration 4-4)
  • Connect new VS. UniSystem control panel to harness and fasten down (see illustration 4-4)
Page 18
NOTE: These steps are for all games
  • Screw on new serial number plate next to old plate.
IMPORTANT! Do not remove old plate (see illustration 4-5)
  • Attach FCC Class A label (see illustration 4-6)

A. Remove old FCC label B. Putonnew FCC label and staple all four corners

Page 19
  • Attach FBI sticker

A. Place label on back door just under lock (see illustration 4-7)

Page 20

Side Decal Application

Step 1.

Start by peeling the protective backing “A” down about 6 inches from the top.

Place decal in desired position. Pull down slowly the remainder of the protective backing of “A.’”

While doing this, use a soft cloth to smooth decal onto side board, moving from top to bottom of decal.

Step 2.

Fold remaining decal back, exposing the unprinted side. Begin to peel protective backing “B”’” from center to right hand side “‘slowly.”’

Using soft cloth smooth decal onto side panel by running hand from top to bottom of decal, moving outward to the right hand side.

Front View

Page 21

V. Final Check Sheet and Adjustments

  • FBI sticker installed (MANDATORY)
  • New serial number plate installed (MANDATORY)
  • New FCC label installed (MANDATORY)
  • Fuse label changed (Popeye only)
  • P.C. Board adjustments made (see P.C. Board adjustments page 20)
  • Monitor adjustments made (see monitor adjustments pages 21-22)
  • Coins give credit
  • Controls on operation panel functioning
  • Sound checked
Page 22

Adjustments

After powering up the game, you will probably find that the screen’s horizontal width is too narrow and the vertical height is too small. To make adjustment to the horizontal width, refer to the illustration on page 21. To adjust the vertical height, use the V-size adjustment on the rear of the monitor to make the picture larger (see page 22).

MDS P.C. Board

NOTE: Only SW2 is used for VS. UniSystem™ games
NOTE: Only these pots are used for VS. Unisystem VR3 VR4 VR6 MDS-CPU

Component Side

Cautions: (1) Since the Dip Switch settings (SW2 only) may be changed by new game software, refer to the new game instructions in Operation Manual for VS. Pak.

  • Do not touch the fixed variable resistors (VR1, VR2, VR3, VR4, VR5, and VR6), as they have already been preset and do not need adjustment.’
  • If, however, color does not look correct, VR3, VR4, and VR6 may be adjusted.
Page 23

Adjustment of Horizontal Width

Using a standard 2.6mm hex non-conductive core alignment driver, carefully turn L453 counterclockwise for a smaller horizontal screen size. L453 is located in the rear of the monitor just under the deflection yoke.

Alignment Tool

\ Heat Sink

UY Turn this way for

a smaller horizontal screen size

CAUTION! HIGH VOLTAGE! BE CAREFUL
Page 24

Adjustment of Video Monitor

To Game PCB _ Video Monitor 6P—600 Video < Main PCB

Harness RS Signal PCB

INVERT OUT NON INVERT OUT

This Signal PCB is only attached to TPPU-20-00 Video Monitor (32 Type) 20-EZV (R-C).

BRIGHT

SOUND VOLUME

& H HOLD Fuse 4A (Slow Blow) in

Video Monitor QO

Nv Main PCB

Fuse 0.3A (Midget Type)

WARNING

Do not touch the inside of the Video Monitor. It contains many parts supplied with high voltage.

Page 25

Nintendo

SERVICE DEPARTMENT

Dear Customers:

In addition to the steps you have already done, we felt it would benefit you if the previous cabinet and coin selector problems were checked to ensure the modifications had been done. Below is the list of service bulletins which deal with these problems.

We have included copies of these service bulletins:

TKG-08 Slam Switch 4-18-82

DJR-01Upper Coin Door Hinge8-24-82
DJR-02Model 730A Coin Selector1-04-83
DJR-08Video Wrap Around9-09-83

Sincerely,

Nintendo of America, Inc.

1-800-633-3236 keV 1-206-882-2040

Page 26

Nintendo

SERVICE DEPARTMENT BULLETIN # TKG.05

GAME: Donkey Kong, Donkey Kong Junior, Popeye, Mario Bros., Donkey Kong 3, VS System

SUBJECT: Slam Switch

In order to prevent the accumulation of free credits by kicking the coin door, a slam switch should be added.

In all cases the switch (a “normally open” weighted reed switch) should be mounted on the coin door. Connect one side of the slam switch to the brown wire on the coin switch (ground). The other side of the slam switch should be connected to a wire which will be run through the wiring harness to the CPU board. At this point the installations vary for the six (6) games.

Donkey Kong:

TKG2 and TKG3: Attach to Test Point 8, at board coordinates 3h.

TKG4: Attach to Test Point 2-RESET, at board coordinates 1L.

Donkey Kong Junior:

Attach to Test Point 2-RESET, at board coordinates 1L.

Popeye:

Attach to C13 (474 F electrolytic capacitor), +” side, at board coordinates 2N.

Mario Bros:

Attach to C38 (1004 F electrolytic capacitor), +" side, at board coordinates 4F.

Donkey Kong 3:

Attach to C25 (100 F electrolytic capacitor), ‘‘+" side, at board coordinates 2E.

VS. System

Attach to C3 (10y electrolytic cap) +” side, at board coordinates 1K.

1-800-633-3236 —o 1-206-882-2040

Page 27

SERVICE DEPARTMENT BULLETIN # DJR-01

GAME: Donkey Kong Jr.

GAME: Donkey Kong Jr SUBJECT: Upper Coin Door Hinge

It has been brought to our attention that a flattened straw or similar object can be passed through the center opening in the upper hinge. If the object makes contact with the coin switch, it can be used to run up multiple credits.

The solution is to block the opening with a flange made of wood or metal. This flange should be mounted to the inside of the cabinet and can be obtained from us as a retrofit kit.

This problem is presented in all Radar Scope uprights, Donkey Kong uprights and early Donkey Kong Jr. uprights.

1-800-633-3236 GG. 1-206-882-2040

Page 28

Detail Coin Mech. yy FeO HDLIMS ADAWSIS

Retrofit Flange

NOTE: Mount

new flange on

left coin mech

using existing

nuts and bolts so flange covers hinge when door is closed.

Page 29

Nintendo

SERVICE DEPARTMENT BULLETIN # DJR-02

GAME: Donkey Kong Jr.

GAME: Donkey Kong Jr SUBJECT: Model #730A Coin Selector

It has come to our attention that there is a problem with the model #730A coin selector in that a nickel or a penny, if flipped through the entry just right, will continue through the mechanism and establish credits.

The solution to this problem is to add a small metal piece to the selector as shown in the enclosed drawing. This piece can be made from 18 gauge steel or even a paper clip as shown in the drawing. This piece is available at no charge. The threaded hole in the selector is an M83 x 6 MM size. If you cannot locate a screw this size, you can remove one of the machine screws from the power supply cage.

1-800-633-3236 ——————————— 1-206-882-2040

Page 30

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 31

Nintendo

SERVICE DEPARTMENT BULLETIN # DJR-05

GAME: Donkey Kong, Donkey Kong Junior

SUBJECT: Video Wrap Around on Left Side of Picture

We have recently received a number of service calls concerning the wrap around or fold over of the picture on the left hand side of the monitor. In most cases the problem may be solved by replacing capacitor C407 on the main monitor PC board. This is located just to the left of the high voltage cage when viewing from the rear of the monitor. The value of this capacitor is 10 microfarads at 160 volts (of course, any capacitor of 10 microfarads with a voltage rating higher will work also).

This capacitor is connected between ground and the B+ supply for the vertical output transistors, so if this capacitor becomes leaky it does not allow full vertical deflection of the screen; consequently, you get video information imposed over the other (wrap around).

If you have questions about this or any other questions concerning Nintendo products, please feel free to contact us.

Page 32

IX. Reorder Parts List

Body Parts — Front View (Fig. 5-1)

ITEM

OMBNONAON= PART NO.

TKGU-01-01 TKGU-01-69 TKGU-01-56 TKGU-01-29 TKGU-01-29-01 TKGU-01-29-02 MGSU-01-24 TKGU-01-49 TPPU-01-52 TPPU-01-50 TPPU-01-51 TKGU-20-00 TKGU-20-01 TPPU-01-68 TPPU-01-67 MGSU-01-23 MGSU-23-60 TKGU-01-31 TKGU-01-28 TKGU-01-02 TKGU-01-02-01 TKGU-01-04 TKGU-01-01-03 MDSU-01-32 TKGU-01-11 TKGU-01-33 TMAU-11-20 TKGU-01-64 TKGU-01-72 TKGU-01-53 MGSU-11-23 TKGU-01-43 DESCRIPTION

Body Center Trim Top Trim Fluorescent Lamp Ass’y Fluorescent Lamp Lamp Starter (Glow Lamp) Name Plate Plexi Speaker Grill Monitor Support Bar Monitor Mounting Brkt Left Monitor Mounting Brkt Right Video Monitor (20-5F) (Standard Scan) Video Picture Tube Blind Cardboard (Small) Blind Cardboard (Large) Front Screen Operation Panel Ass’y Draw Latch Coin Door Coin Selector Coin Switch Front Door Lock Cash Box CS Frame 120 W Ass’y Game Counter Service Switch CS Plate 120W (Only) Service Switch Bracket T Molding (White) Front Screen Frame (Lower) Side Decal Speaker 16cm (8 OHM)

Page 33

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 34

IX. Reorder Parts List, Continued

Body Parts — Rear View (Fig. 5-2)

ITEM

ODNOANAONS PART NO.

TKGU-01-01-05 TKGU-01-03 TKGU-01-03-01 TKGU-01-05 MDST-21-11 MDSU-01-01-11 MDSU-01-01-12 MDSU-01-01-13 MDSU-23-35 TPPU-01-01-14 CHPU-01-01-15 TKGU-01-08 TKGU-01-10 TKGU-01-65 TKGU-11-08 TKGU-01-30 CHPU-01-01-10 TKGU-18-01 TKGU-09-01-01 TKGU-01-07 MGSU-11-05 TPPU-11-25 TKGU-11-17 MGSK-23-61 TPPU-01-67 TPPU-01-68 TKGU-20-00 TKGU-20-01 TKGU-10-01 TKGU-10-01E TKGU-01-01-02 TKGU-09-01-02 TKGU-09-01-03 TKGU-19-01-03 DESCRIPTION

Back Door Back Door Lock (Key #6510) Back Door Key Only (Key #6510) Cam A-lype (Back Door Lock) PC. Board Ass’y 062 FCC Shield Cover 062 44P FCC PC.B. Ass'y 062 36P FCC P.C.B. Ass’y Snap In Fastener FCC Sponge (Black) Shield Cover Label Power Cord 5M Strain Relief Bushing Strain Relief Bushing Plate Fuse 5A 125V Caster Shield Cage (054 Type) Power Supply PP-7B Power Transformer PT821B Back Door Lock Stopper Plate Back Door Label FCC Label Monitor Adjustment Label MGSK Operation Manual Blind Cardboard (Large) Blind Cardboard (Small) Video Monitor (20-EZV) (Standard Scan) Video Picture Tube Power On/Off Switch Ass’y (90 ~ 120v) Power On/Off Switch Ass’y (200 ~ 240v) Transformer Base 100v Outlet (From Transformer) Terminal Block 6-Position Terminal Block 4-Position

Page 35

Rear View of Game Cabinet

Page 36

Operation Panel Assembly (Fig. 5-3) ITEM PART NO. DESCRIPTION

1MDST-14-128 Way Control Lever Assembly
2TKGU-23-21Switch Collar
3TNX-23-188 Way Guide Plate
4TKGU-23-17Switch Spacer
5TKGU-23-16Bearing Brkt
6TKGU-23-20Spring Stopper
7TKGU-23-22Lever Spring
8TKGU-23-23E-Ring
9TKGU-23-13Micro Switch
10TMAU-12-15Lever Plate
1TMAU-12-14Control Knob Plate
12TMAU-12-16Control Knob Collar 8L
13TMAU-11-18Knob with Shaft 80.5L
14MGSU-01-22Operation Panel Base
15TKGU-23-12Switch Button Bracket
16TMAU-34-18Micro Switch VL 12L (Straight)
17MDSU-12-17Black Sponge, 2 x 10 x 580L
18TKGU-23-26Nut Plate
19TKGU-23-34Pal Nut M16
20MDST-12-21Button Assembly (Black)
21MDST-12-17Button Assembly (Crimson)
22TMAK-11-19Operation Panel Fastener
23TMAU-12-18Collar — 34 x 28 x 7H
24MDST-12-24Button Assembly (Light Blue)
25MDST-12-27Button Assembly (Green)
Page 37

VS. UniSystem Operation Panel Assembly Parts (Upright)

5-3

Operation Panel Assembly

Page 38

Wiring Harnesses

PART NO. DESCRIPTION

MDSU-41-12 062 44P FCC Harness MDSU-41-11 062 36P FCC Harness MGSU-41-13 UP-072-44P Edge Harness MGSU-41-14. UP-072-36P Edge Harness MGSU-42-11 UP-072-15P Switch Harness MGSU-42-12 UP-072-12P Switch Harness MGSK-43-01 072-6P-100 Video Harness MGSK-43-02 072-2P-100 Audio Harness MGSK-43-03 072-4P-100 Service Sw. Harness MGSK-43-04 072-4P-100 Coin Sw. Harness MGSK-43-05 072-3P-100 Counter Harness MGSK-43-06 072-9P-250 Power Harness TKGU-13-17 2P-860 Speaker Harness

Page 39

MDS P.C. Board Assembly PART NO. DESCRIPTION (Reference Designations and Locations) MDST-21-11 P.C. Board Assembly

MDST-21-122A03 Microprocessor(2J,8J)
MDST-21-13HM61162k x 8bit Static RAM, 250ns(6E)
MDST-21-14MB8416-15 2k x 8bit Static CMOS RAM 150ns(8L)
MDST-21-15TC5533P-A 4k x 8bit Static RAM(2C)
MDST-21-16TC5533P-B 4k x 8bit Static RAM(8C)
MDST-21-1774LS00 Quad 2-input NAND LS TTL(4C, 5C)
MDST-21-1874LS04 Hex Inverters LS TTL(1L, 2K, 4E, 5E)
MDST-21-1974LS10 Tri 3-input NAND LS TTL(4D)
MDST-21-2074LS32 Hex 2-input AND LS TTL(4A, 4B, 5A, 5B)
MDST-21-2174LS74 Dual D-Flip Flops LS TTL(5D)
MDST-21-2274LS123 Dual Retriggable Single Shots LS TTL(1d)
MDST-21-2374LS138 Dual 2 to 4 Demultiplexers LS TTL(1F, 6F)
MDST-21-2474LS157 2 to 1 Data Selectors LS TTL(5J, 5K, 6J, 6K)
MDST-21-2574LS165 8bit Shift register LS TTL(6M, 6N, 7P, 8P)
MDST-21-2674LS240 Octal 3 State Bus. Inverters LS TTL(7M, 7N, 8M, 8N)
MDST-21-2774LS245 Octal 3 State Bus Transceivers LS TTL(3K, 8K)
MDST-21-2874LS373 Octal 3 State D-Latchs LS TTL(2E, 8E)
MDST-21-2974F04 Hex Inverters FAST TTL(5H)
MDST-21-304066 Quad Analog Switches C-MOS(2P, 4P)
MDST-21-31LM324 Hex Operational Amplifiers(1P, 3P)
MDST-21-32LM3900 Hex Operational Amplifiers(5N, 5R)
MDST-21-33PST518A Reset IC(1K)
MDST-21-342SA933 Silicon PNP Transistor(Q3, Q7, Q13 ~ Q16, Q19 ~ Q22, Q26, Q27)

MDST-21-35 2SC1740 Silicon NPN Transistor (Q1, Q2, Q4 ~ Q6, Q8, QY, Q12, Q17, Q18, Q23 ~ Q25) MDST-21-36 2SD592 Silicon NPN Transistor (Q10, Q11) MDST-21-37 18953 Silicon Switching Diode (D1, D2, D5, D7, D9~ D11)

MDST-21-38W03B Silicon Diode(D3, D4, D6, D8)
MDST-21-3927 Q1/4W + 5% Resistor(R4)
MDST-21-4033 21/4W + 5% Resistor(R22, R30, R36, R38, R45R47, R72, R89)

MDSF-21-41 100 21/4W + 5% Resistor (R79, R80, R95, R97) MDST-21-42 330 21/4W + 5% Resistor (R8, R20, R28, R29, R48, R49, R70, R71, R73, R91)

MDST-21-43680 21/4W + 5% Resistor(R119)

MDST-21-44 1K 21/4W + 5% Resistor (R31, R32, R92, R93) MDST-21-45 1.2K 21/4W + 5% Resistor (R37, R43) MDST-21-46 2.2K 21/4W + 5% Resistor (R6, R11, R12, R14, R15, R23, R24, R27, R39 ~R42, R50, R51, R54, R55, R64, R65, R68, R69, R81, R87)

MDST-21-473.3K 21/4W + 5% Resistor(R77)
MDST-21-484.7K Q1/4W + 5% Resistor(R13, R17, R25, R26, R52, R53, R66, R67)
Page 40

MDS P.C. Board Assembly (continued) PART NO. DESCRIPTION (Reference Designations and Locations)

MDST-21-4910K 2 1/4W + 5% Resistor(R3, R5, R7, R16, R18, R19, R21, R33, R56

R63, R75, R82, R83, R85, R86, R120)

MDST-21-5012K 21/4 W + 5% Resistor(R76, R96, R98)
MDST-21-5120K 21/4W + 5% Resistor(R94, R99)
MDST-21-5233K 21/4W + 5% Resistor(R1, R2)

MDST-21-53 100K 2 1/4W + 5% Resistor (R10, R35, R84, R103, R121)

MDST-21-54150K 2 1/4W + 5% Resistor(R74, R118)
MDST-21-55360K 21/4 W + 5% Resistor(R107, R114)

MDST-21-56 750K 21/4W + 5% Resistor (R101, R108, R109, R110, R115, R116) MDST-21-57 1M 21/4W + 5% Resistor (R102, R106, R112, R117)

MDST-21-581.8M 21/4W + 5% Resistor(R90, R105)
MDST-21-592.2M Q1/4W + 5% Resistor(R81, R87, R100, R104)
MDST-21-601K 2x8Series Resistor Array(RM1, RM2, RM5, RM8, RM11, RM14, RM17)

MDST-21-61 68 2 x 4 Parallel Resistor Array (RM3, RM4, RM6, RM7, RM9, RM10, RM12, RM13, RM15, RM16)

MDST-21-6233pF 50V Ceramic Disc Capacitor(C35, C91, C92)
MDST-21-6368pF 50V Ceramic Disc Capacitor(C25, C86)
MDST-21-64100pF 50V Ceramic Disc Capacitor(C38, C42, C43, C46)
MDST-21-65220pF 50V Ceramic Disc Capacitor(C26 ~ 29, C34, C45)
MDST-21-660.01 p F 50V Ceramic Disc Capacitor(C9, C10, C89, C90)
MDST-21-670.1 p F 25V Ceramic Disc Capacitor(C100 ~C178)
MDST-21-680.2 p F 12V Cerarnic Disc Capacitor(C4, C12)
MDST-21-690.047 p F 50V Film Capacitor(C37, C39, C40, C44)
MDST-21-703.3 uw F 16V Al. Electrolytic Capacitor(C15 ~ C18, C31, C32)
MDST-21-7110 p F 16V AI. Electrolytic Capacitor(C3, C5, C6, C11, C13, C14, C19 ~ C24, C30,

C33, C36, C41, C47 ~ C85)

MDST-21-7247 p F 16V Al. Electrolytic Capacitor(C2)
MDST-21-73100 p F 16V Al. Electrolytic Capacitor(C1)
MDST-21-74100 # F 25V Al. Electrolytic Capacitor(C8)
MDST-21-75470 p F 16V Al. Electrolytic Capacitor(C7, C87, C88)
MDST-21-76500 © Variable Resistor. Red Cap(VR1, VR3)
MDST-21-77500 Q Variable Resistor. Green Cap(VR2, VR4)
MDST-21-78500 Q Variable Resistor. Blue Cap(VR5, VR6)
MDST-21-7921.47727MHz Crystal(X1)
MDST-21-808 position dip switch(SW1, SW2)
MDST-21-8128P IC socket(1A, 1B, 1C, 1D, 2A, 6A, 6B, 6C, 6D, 8A, 8B)
MDST-21-8240P IC socket(2F, 2J, 8F, 8J)

MDST-21-83 Type 32-4 (UMS x 2) Battery Case MDST-21-84 Bolt with washer M2.6 MDST-21-85 Flat washer M2.6 MDST-21-86 Nut Plate M2.6 MDST-21-87 Dry Battery “AA’”’ T18L Beaded tie

Page 41

Power Supply Parts (PP7B)

Part No. Description

TKG-18-01(PP-7B) Power SupplyComplete
TKG-18-02Transistor2S8C2555
TKG-18-03Transistor2SA817
TKG-18-04Transistor28C2535
TKG-18-05Transistor2SA1015
TKG-18-06Fast Recovery Center Tap DiodeCTU-2S
TKG-18-07Shot Key DiodeCTB33S
TKG-18-08Silicon Rectifier DiodeS4VB40 4A 400VW
TKG-18-09Silicon Rectifier Diode1B4B41
TKG-18-10Hybrid IC3D-1001
TKG-18-113 Terminals Regulators7824
TKG-18-123 Terminals Regulators7812
TKG-18-13Thyristors5P4M
TKG-18-14Thyristors03P05M
TKG-18-15Diode18954
TKG-18-16Diode10DF-4
TKG-18-17Photo CouplerPC614
TKG-18-18Zener Diode05Z5.6U
TKG-18-19Zener Diode0525.1L
TKG-18-20Zener Diode05Z5.6Z
TKG-18-21Ceramic CapacitorDE0707B471K2K 470pF2KV
TKG-18-22Ceramic Capacitor0.1MF 50V
TKG-18-23Film CapacitorMDD2J473M 0.074MF 630VW
TKG-18-24Film Capacitor0.01MF 50V
TKG-18-25Film Capacitor1000pF 50V
TKG-18-26Aluminum Electrolytic Capacitor1000MF 50V
TKG-18-27Aluminum Electrolytic Capacitor47MF 35V
TKG-18-28Aluminum Electrolytic Capacitor47MF 16V
TKG-18-29Aluminum Electrolytic Capacitor3300MF 10V
TKG-18-30Aluminum Electrolytic Capacitor100MF 25V
TKG-18-31Aluminum Electrolytic Capacitor10MF 16V
TKG-18-32Aluminum Electrolytic Capacitor330MF 200V
TKG-18-33Aluminum Electrolytic Capacitor1000MF 25V
TKG-18-34Resistor (Coil Winding)20 OHM 2W
TKG-18-35Resistor (Carbon)1K OHM 14W + 5%
TKG-18-36Resistor (Carbon)51 OHM 4W+5%
TKG-18-37Resistor (Carbon)12 OHM 1hW+5%
TKG-18-38Resistor (Carbon)470 OHM 14W + 5%
TKG-18-39Resistor (Carbon)22 OHM "2W+5%
TKG-18-40Resistor (Carbon)20K OHM VeW + 5%
Page 42

Power Supply Parts (PP7B), continued

Part No. Description

TKG-18-41Resistor (Carbon)100 OHM ‘/2W
TKG-18-42Resistor (Cement)20 OHM 5W
TKG-18-43Resistor (Metal Oxide)510 OHM 3W
TKG-18-44Variable Resistor50K OHM GFO6P
TKG-18-45Variable Resistor2K OHM GFO6P
TKG-18-46Shunt Resistor5m OHM
TKG-18-47SC CoilSC-02
TKG-18-48SF Coil100MH 5A
TKG-18-49SF Coil800MH 2A
TKG-18-50Oscillator TransformerEC-35 Type 3D-0097
TKG-18-51Oscillator TransformerEl-30 Type 3D-0097
TKG-18-52Oscillator TransformerEE-16 Type 3D-1000
TKG-18-53Fuse ElementFGMB 4A 125V NR Type
Page 43

MONITOR PARTS (20-EZV) MONITOR PARTS (20-EZV), CONTINUED PART # DESCRIPTION PART # DESCRIPTION

MON-01-01IC LA1464MON-09-06CERAMIC CAPACITOR 820PF 500V
MON-01-03IC LAS112MON-09-08CERAMIC CAPACITOR 1000 PF 1000V
MON-02-01DIODE 181555MON-09-10CERAMIC CAPACITOR 200PF 2000V
MON-02-02DIODE 181553MON-09-12CERAMIC CAPACITOR 500PF 2000V
MON-02-03DIODE EU-1MON-09-50ELECTRO CAPACITOR 47MF 10V
MON-02-04DIODE RU2MON-09-52ELECTRO CAPACITOR 470MF 10V
MON-02-05DIODE SIB01-02MON-09-54ELECTRO CAPACITOR 100MF 16V
MON-02-06DIODE ERCO04-06MON-09-56ELECTRO CAPACITOR 220MF 16V
MON-02-07DIODE 1S188TVMON-09-58ELECTRO CAPACITOR 4.7MF 25V
MON-02-50ZENER DIODE EQA01-35MON-09-60ELECTRO CAPACITOR 220MF 25V
MON-02-51ZENER DIODE EQA01-07MON-09-62ELECTRO CAPACITOR 330MF 25V
MON-02-52ZENER DIODE EQA01-12MON-09-64ELECTRO CAPACITOR 1MF 160V
MON-02-53ZENER DIODE HZ7MON-09-66ELECTRO CAPACITOR 10MF 160V
MON-03-01TRANSISTOR 2SA673(A)MON-09-68ELECTRO CAPACITOR 100MF 160V
MON-03-02TRANSISTOR 2SA940MON-09-70ELECTRO CAPACITOR 470MF 160V
MON-03-03TRANSISTOR 2SA659MON-10-00MYLAR CAPACITOR 0.047MF 100V
MON-03-51TRANSISTOR 2SC536MON-10-02MYLAR CAPACITOR 0.082MF S0V
MON-03-52TRANSISTOR 2SC2551MON-10-04MYLAR CAPACITOR 2700PF 50V
MON-03-53TRANSISTOR 2SC1015MON-10-06MYLAR CAPACITOR 0.33MF 50V
MON-03-54TRANSISTOR 2SC1051MON-10-08MYLAR CAPACITOR 0.1MF 50V
MON-03-55TRANSISTOR 2SC1507MON-10-10MYLAR CAPACITOR 8200PF 50V
MON-03-56TRANSISTOR 2SC2073MON-10-12MYLAR CAPACITOR 0.015MF 50V
MON-03-57TRANSISTOR 2802228MON-10-14MYLAR CAPACITOR 0.056MF 50V
MON-03-58TRANSISTOR 2SC2271MON-10-16MYLAR CAPACITOR 0.068MF 50V
MON-03-76TRANSISTOR 2SD386-AYMON-10-30POLYPRO CAPACITOR 0.056MF 160V
MON-03-77TRANSISTOR 2SD870MON-10-32POLYPRO CAPACITOR 0.47MF 200V
MON-03-78TRANSISTOR 28D1090MON-10-34POLYPRO CAPACITOR 0.022MF 200V
MON-03-79TRANSISTOR 2SD901MON-10-36POLYPRO CAPACITOR 2200PF 630V
MON-03-80TRANSISTOR 2SD869MON-10-38POLYPRO CAPACITOR 6800PF 2000V
MON-05-01FUSE RESISTOR 1W 39 OHMMON-11-00SOLID RESISTOR 1/2W 1.8 KOHM
MON-05-02FUSE RESISTOR 2W 330 OHMMON-11-30CARBON RESISTOR 1.2W 100 OHM
MON-05-03FUSE RESISTOR 1/2W 1 KOHMMON-11-32CARBON RESISTOR 1/2W 1 KOHM
MON-05-04FUSE RESISTOR 1W 3.3 OHMMON-11-34CARBON RESISTOR 1/2W 10 KOHM
MON-05-083 KOHM VARIABLE RESISTORMON-11-36CARBON RESISTOR 1/2W 120 OHM
MON-05-1010 KOHM VARIABLE RESISTORMON-11-38CARBON RESISTOR 1/2W 18 OHM
MON-05-1250 KOHM VARIABLE RESISTORMON-11-40CARBON RESISTOR 1/2W 39 KOHM
MON-05-14200 KOHM VARIABLE RESISTORMON-12-00WIRE WD RESISTOR 20W 180 OHM
MON-05-16450 OHM VARIABLE RESISTORMON-12-02WIRE WD RESISTOR 7W 470 OHM
MON-05-18300 OHM VARIABLE RESISTORMON-12-04WIRE WD RESISTOR 7W 1.5 OHM
MON-06-01TRANSFORMER A7007MON-12-30OXIDE M RESISTOR 1W 1 KOHM
MON-06-02LINEARITY COIL (A0285)MON-12-32OXIDE M RESISTOR 1W 18 KOHM
MON-06-04WIDTH COIL (A7018)MON-12-34OXIDE M RESISTOR 1W 330 OHM
MON-06-05FILTER COIL (L7133)MON-12-36OXIDE M RESISTOR 1W 8.2 KOHM
MON-08-06LINE FILTER (LO19D)MON-12-38OXIDE M RESISTOR 2W 10 KOHM
MON-06-21FLYBACK TRANSFORMER F5024MON-12-40OXIDE M RESISTOR 2W 5.6 KOHM
MON-06-50YOKE COIL (20-5F TYPE)MON-12-42OXIDE M RESISTOR 3W 1.2 KOHM
MON-06-60PURITY MAGNET ASSY (20-5F)TKGU-20-01VIDEO PICTURE TUBE (510UTB22)
MON-07-01FUSE 4ATKGU-20-02MONITOR MAIN PCB
MON-07-02FUSE 0.3A(W/ICOMPONENTS)
MON-08-01THERMIST SDT-500TKGU-20-03MONITOR AUDIO PCB
MON-08-02THERMIST SDT-1000(WICOMPONENTS)
MON-08-50POSISTOR PTH451C05TKGU-20-04MONITOR CRT PCB (W/COMPONENTS)
MON-09-00CERAMIC CAPACITOR 5PF 50VTKGU-20-07MONITOR INVERTER PCB
MON-09-02CERAMIC CAPACITOR 470PF 500V(WICOMPONENTS)

MON-09-04 CERAMIC CAPACITOR 4700 PF 500V

Page 44

PRINTED IN U.S.A.

Page 45

©) ©

/21 PSvae | | reooso08} Loew} Luan |

im

©

PICTURE TUBE COLOR GUNS

12V(from 108VDC) 23 into sync amp/separator 12V(from 16VDC) 24 (vert. supply)

into hold down circuitry com

Sie richie

2:

DEFLECTION YOKE HIGH OL TAG

Page 46

Description of Video Monitor Block Diagram

. 100VAC is applied . Rectified by D601, 602, 603, 604 . 1C601/TR901 form regulator for B + . B+ is distributed

G, R, B color signals applied . Amplified by the respective transistors . Amplified again at neck board . Bias provided by brightness voltage . Applied to picture tube guns

. Sync is applied, buffered by TR204 . Apply sync to 1464 sync amp & seperator

. Vertical pulse out of pin 5 is amplified by TR401, then by TR402/403 . Vertical pulse applied to deflection yoke

. Horizontal drive pulse out of pin 10 is amplified by TR451 . Amplified again by TR902 (horizontal output) . Applied to flyback transformer which distributes voltages

. Feedback from flyback monitors pin 7 pulse and will apply hold-down pulse to pin 9 of 1464 should over voltage exist

Page 47

eeonivianst PICTURE TUBE SOCKET BOARD utes?

=Beecoe CONTROL CIRCUIT BOARD UBB5493

or

veo Gan 8H 6 GK TO MAIN CHASSIS CIRCUIT BOARD

“FROM MAIN CHASSIS CIRCUIT BOARD

vers, ourrur. an

3308

Sse bd LT sor

woRiz. ORIVE Rast 25032720, Beate)

MAIN CHASSIS CIRCUIT BOARD _U 885486 crx f B0NG SE, HOR Ego" far ie youan ns iter

t

cag aaa eee [2K ay ok 7 nase uss ooo FS Cade gt | Bein nace. 700° 7

2200 Jove 20006 dteop roop “S00

tai Tiel y630 “£6 3334 a jan) every 7 f Ayprowar ERY} cuszsoety amd

Kae

  • TRANSISTOR BASE INFORMATION.

<. 250000 _ BE.

= ES

mm ase ad BS Ea = : = Ne ~

  • RESISTOR, CAPACITOR: INFORMATION. ‘+ RESISTOR — INFORMATION. F io I “ES nesiston LS nesston vatue ina. POWER RATING. AS TO 1/4W F-TYPE RESISTORS, RESIST. ANCE VALUES ALONE ARE GIVEN. SoqCAPACITOR — INFORMATION EXPRESSED IN P WHEN THE UNIT ISPE OTHERWISE OMITTED. ‘RATING VOLTAGE (THE UNIT “V" OR "WV" IS OMITTED.) AS TO “SOV. C-TYPE” CAPACITORS VALUE IS ONLY GIVEN.
  • THIS BEING A FUNDAMENTAL SCHEMATIC ‘THERE WILL BE SOME CASES THAT THE REAL CIRCUIT DOES NOT COINCIDE WITH THIS.

RESISTOR TYPE F; INSULATED FIXED CARBON FILM RESISTOR. NN: INSULATED METAL FILM FIXED RESISTOR, R; INSULATED FIXED METAL OXIDE FILM RESISTOR.

: FIXED CARBON COMPOSITION RESISTOR.

CAPACITOR Ty:

FIXED CERAMIC CAPACITOR, RADIAL TYPE ALUMINUM ELECTROLYTIC GaPaciTOR £ ; POLYESTER FILM CAPACITOR } POLYPROPYLENE FILit CAPACITOR, INP); NON-POLAR ALUMINUY ELECTROLYTIC CAPACITOR,

20-EZV(R-C) SCHEMATIC

©1982 Nintendo of America Inc. Hinman

fa

Page 48

SWITCHING POWER SUPPLY

Block Diagram

LOOVAC is stepped down and rectified

vcc (12VDC) is applied to ICl; starts switching

ICl switching drives TR2/T3, which in turn drives TR1/

Secondary of Tl output is rectified by D4 & DS

After filtering, D5 output is -5V

D4 output supplies 3 terminal regulator 7824

7824 output is +24V; also drives 3 terminal regulator 7812

7812 output is +12V; also VCC for IC2

IC2 switching drives TR4/T4; which in turn drives TR3/T2

D9 rectifies T2 output which becomes +5V @OOOOOOOOOO

Page 49

Trouble Shooting chart for PP-7B

ALL VOLTAGES

AC INPUT

CHECK 5s FUSE & AI

REMOVE SCR2 CHECK VOLT. WITHIN LIMITS: Yes Bad

CHECK Ic3, ica, 04,05 02,03

CHECK 07,08,D9 CHECK 1C1, Ic2 & assoc. cIRCUITS CHECK 201, ZD2 & ASSOC. SHUT-| DOWN CIRCUIT CHECK D2, D7 SCcR1, D1

TR

NO OUTPUT

+5, *12,+24 NO OUTPUT +5 VOLTS

CHECK L5,D9,

ice NO OUTPUT

-5 VOLTS

CHECK L2,L3

1c3, Ica

Page 50

ip 8047; 650vw

E16 Tr8 25A817

O14 1$95¢

FG

cas 6.047 ar 639vw

20, 1221)

a8

Tr3 2SA817 3BFWJ2CI

; § on ~O+5V

E Pose TS Tra 25asmy_|

S UL Power Supply (PP=74) a 1$.56,9,25)

eS (ena) ee SOILVWSHOS AlddNS YSAMOd

Page 51

FG BRI save: Rs fo De 18954 cc35 cTv-25,

anv ut sce2

aky

ca + 68ety 6380

Gna aor [|| * of t c6,c7 xz® Ci C3 7,3] a‘ AT y%6V%3) 637

TS BR2 184841 R28 1K 13 Yen 22. GNO) 15, A201 S riz ts LASSE Pees ‘ ASSES te e Leoneas k L & ys

  • ke Sr SCRE Rete ae [O8P85M

HV: ie, T2 E130

PG LI a s90Fe AK

Kis < 535 Té EEG

Rig ot wet R28 ewe 3 08 190F-4 GND

lo S Zeicrscrace9re | 47 tov

GNO a's

+5V

(FAB I36.9.25

~ A mame WlSne GR

Page 52

44P Edge Connector 062 40P FCC Connector ‘9

HD a ——s a en GND ‘EN GND

tet — enotsoTe
téamifVv[oa
ts72,cy
3150aEy

av +72V

fa Relav+oi2

Hav {+ E| E co

Seon+Seon77
amcorawicomZl
SCON?,+‘sconzcs
Fel coma+=peo2
SRED.+FoSED
MRED1G.a:
S GREEN,+reaSane:

M GREEN * a. VIDEO GNO v1 S BLUE fe

M BLUEanre
SYNC+ro
MSYNC+Le

i

av—+aa
7=+'S COUNTER,

COUNTER ‘M COUNTER M COUNTER ¢

kl 'S SERVICE,tofea ue
M SERVICE7Sev
'$ SOUND!Ss0uN0.
‘MSOUND,+sour

‘GND ox = = GHO ow = AE CEOELECEEEG

SCHEMATIC

owe 3710/84 062 44P FCC PC Board Nintendo of America Inc

Page 53

MDS PCB

Be

062 44P FCC HARNESS

1 ‘ENO eae ry GND Sek ae A te Gi ‘BLACK ele te Ea suck} +H Het FE RED re HY

RED E =— ete 2

ED 12v ORANGE He ts ry PAmert segn 5 M_COIN, ee s Sone ced a i se RED tS Sa BED : FH es o 2 S GREEN BROWN Ris Sanko1 snow a Ho) 44 V. GND YELLOW QO bl a a| too YELLOW 0 aKa} ———— t @ M BLUE RANGE earn our

UE ee ao § = + |

  • ORANGE cr “2a ORANGE q AF ‘M COUNTER, BROWN et o
  • vetow E) ‘SS SERVICE ST ‘M SOUND +} ‘S'SOUND A

aRown RA = on oe BLACK GND BLACK.

062 36P FCC HARNESS

4 a eae i= ne fat = ‘S1 RIGHT BROWN. ‘M1 RIGHT BROWN tet [St ——sicerr RED HF 3 SiUP ta; stor aae—tets) [S| — steam veiw 99h Q ni LE}. gaa YELLOW Le} eco —\vertow once 9 o rey 2 ere ee as 8 $1 B SWITCH MGT BLUE. 5S ed ts] ta ae 1818 Lo J re PURPLE ial =a

“GRAY SELECT a © fra ‘$2 RIGHT a i iH erown j25/25) ay mJ ‘RED q | Bt aaa o

ORANGE: 0 Aa! YELLOW [| [ss | m2 Gown row ie [esse aswircw Seay T M2 A SWITCH GRAY Be an wat eal ‘M2 B SWITCH GB se BLACK. Le ava oe BLACK fs!

Vv

44P Edge Harness Connector 36P Edge Harness Connector Pai q a < QO; oO; Fs of oe 3/10/84 062 FCC PC Board Nintendo of America Inc.

Page 54

BROWN

M COIN 2,

‘M GREEN RED

YELLOW GREEN

ORANGE RED YELLOW

WW & ORANGE

om “awe

ae|PURPLE.BROWN7hGND
a<5vORANGEREDazGND
[a |ORANGE3t3GND
D+5YELLOWYELLOW12
5+124

GREEN GREEN

+12V5ov
BLUE3av
PURPLEit+5V

BROWN [a]

‘SCOINTWHITEwav
MCOINTRED9

‘SCOIN2 Power Supply o- RE a ls er erie 7 Power Power Transformer switch fuse, ' 20 ote z ol2 a8 100 sov Powen coro

PP-78

ORANGE

‘M SOUND GND. [end [cnt [sno

[aq cnn [AT cu BROWN [2] [BE | miaicHT | [3 | S1LEFT & ORANGE a E{ moo — | veuowomm | LF | ‘M1 A SWITCH LBLUE ‘S18 SWITCH [He [ ipswich | [Bl ‘S SELECT 1 J M SELECT 1 [3] S SELECT 2 M SELECT 2 CRAY CJS SELECTS [i [ Msevects 4 4|___SSELECT4 M|___MSeLect4 BROWN

a [el wer ORANGE a szup i ee [a5] s2D0wn

Ss M2 DOWN GRAY

Gl S2 A SwitcH

M2 B SWITCH YELLOW

Service

BLACK ° bron rn

/oOg
S2iH
eoHq
3a83

PA g e i rss Fa

oF|.

oO 8 >

VIDEO MONITOR pee eee ee een eee eee eee 4 SOUND P.C.B. I

BROWN _F7t7}_ BROWN 5% nicht!4
REDrome,1
{orange —}2}2{ nance Sot op”1H
K“"veutow “1331 veutow 5-2 | pownoo1
{ seGREENWw|/

Mee Roane | I

era 14 GRAY2p SELECT 2|t
wate 315analt}
BLACKaazi

LT cn | ; Be | i \

Y.GREENY. GREEN1
3H 3}Oo O-—A SWITCH'

Cf teswue iaha L BLUE OO wre z ce, om

'—1|

H 1

BROWN 1717} SROWN oO RIGHT-H}
re)FT'
1212|-onanae ss te<tL-~. ~~~ --

YELLOW 1

GREEN0-4 DOWNa!

I Lu 1 a

RAYa!zRED.
eratOA SWITCH1
BLACKO-#8 SWITCH(o}HSpeaker

' ' VIDEO MONITOR SIGNAL P.C.B.

VIDEO MONITOR MAIN P.C.B.

WIRING DIAGRAM

‘APPROVED 8 onawn ay TUK RevierD scat ears 2/10/85.

VS. UNISYSTEM UP

Nintendo of America Inc. |"Mas_k

Page 55

we

nai 1083 | PIECED wd 12 13

+5V.3A ao ; oe Ff carp ara P2 PI 1@SQOFF0800R aus eae

QM? RICH D2 cert OzES Dez ur TET TOM Sy seu 9 SO ace tirerses

M1 RIGHT Onmtial ror Du ue Dy siz OED 6.5 1B Se [poche rwewee “Om a sw O-NurwaQgay o-vernonewss

ooNu suns saa

JIM cone

xin] ass) LA) comms {i]s sevice

@s2 ricH Yaimsze ass =O s0ut

wecars =z Dome @s2 ve Is S14 —@s sti? POsea

{ exe

~~ @s seus Dst5 5" nak Osrase averen

A

hdd O-nu rel SAy o-wusweveugs

EE awe swe SEATF o-wk senses

oe wenn Sear EI

oe 7807 se Run TR [ays cots 2 ©iM324 412 aay GND 11FIN “scans

$ SouNc (a406E 12 14pm GNG 6, 7em Gs service

THis custom,

‘ MOS-@2-CPU rm

EXSRK Nintendo Ge Sit Lid.