CATHODE RAY TOMES

Super Breakout TM-118 1st Printing

Super Breakout (rev 04) (Atari, 1978) · Technical Manual · 116 pages · 44 sections · original scan

Page 1

‘st PRINTING

Page 2

GAME SERIAL NUMBER LOCATION

Your game’s serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the label located on the rear of the game cabinet. Please mention this number whenever calling your distributor for service. tee

Page 3

Super Breakout”

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Catalog

ATARI INC 1265 BORREGAS AVENUE PO. BOX 9027 SUNNYVALE, CALIFORNIA 94086 408/745-2000 = TELEX 35-7488

A

ATARI

Page 4

Copyright © 1978 by Atari, Inc. All rights reserved

Motorola and TEC service manuals reprinted by permission of Motorola Data Products and TEC Videoelectronics, Inc. No part of this publication may be reproduced by any mechanicai, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

For permissions request, write:

ATARI INC 1265 Borregas Avenue P.O.Box 9027 Sunnyvale, California 94086

ea

Lithographed in the U.S.A.

ii Super Breakout

Page 5

1 LOCATION SETUP A. INTRODUCTION ... 1.0.00... c eee eee bet e eee eee 22. 07 B. GAMEINSPECTION ..0 0.0.00 cence 1-2 C. INSTALLATION REQUIREMENTS Line Voltage Selection. . Type of Power Cord .... D. INTERLOCK, POWER ON/OFF SWITCH AND OTHER OPERATOR CONTROLS Interlock Switch Checkout Procedure .... £. OPERATOR OPTIONS .... F. SELF-TEST PROCEDURE G. VOLUME CONTROL

2 GAME PLAY A. INTRODUCTION .... 22-2000 occ eee cece eee 21 B. ATTRACTMODE .... 2-2 C. READY-TO-PLAY. fats 2-2 D. PLAYMODE............ 29 Double ................ x Cavity ..... nee csc Progressive ...........

3 THEORY OF OPERATION A. GENERAL INFORMATION .... B. POWERSUPPLY................ 000005 C. MICROPROCESSOR CIRCUITRY. MPU, ROM, and RAM ... Address Decoding 0 Clock Driver. Watchdog Reset . . bce c eee SYNC GENERATOR .................. PLAYFIELD GENERATOR ... : MOTION OBJECT GENERATOR .. SWITCH INPUT CIRCUITRY . PADDLE CONTROL . VIDEO OUTPUT... AUDIO OUTPUT

4 MAINTENANCE AND ADJUSTMENTS A. CLEANING ..........-.. B. COIN MECHANISM Components on Coin Door . . Access to Coin Mechanisms . . . Cleaning of Coin Paths .......... Lubrication ........... bie he Adjustment of Coin Switch Trip Wire AT TOA™™D

Super Breakout

Page 6

TABLE OF CONTENTS

Mechanical Adjustments on Coin Mechanism . General Troubleshooting Hints TV MONITOR ADJUSTMENTS .... FUSE REPLACEMENT TV MONITOR REMOVAL. . LAMP/SPEAKER ‘ASSEMBLY REMOVAL. . cee LICON (LED) SERVE SWITCH REMOVAL... .. . LAMP START SWITCH REMOVAL...... PADDLE KNOB {POTENTIOME TER) REMOVAL GAME SELECT SWITCH REMOVAL . 5 ILLUSTRATED PARTS CATALOG ar mam™moo

iv Super Breakout

Page 7

LIST OF ILLUSTRATIONS

Figure1-1 Super Breakout Control Panel... . 1-2 Figure 1-2 Voltage-Selection Connectors............ 1-3 Figure 1-3 Location Set-up Requirements ...... beeen eee . 14 Figure 14 Location of Interlock and Power On/Off Switches . . bees its Figure 1-5 — Option DIP Switches and Game PCB Location and Removal. Le wee A Figure 16 — Location of Self-Test Switch and Volume Control... . . we 18 Figure 2-1 Attract Mode Version One . . 23 Figure 2-1 Attract Mode Version Two .... 24 Figure 2-2 Progressive Breakout Ready- -to-Play Mode . 25 Figure 2-3 Cavity Breakout Ready-to-Play Mode . Figure 2-4 Double Breakout Ready-to-Play Mode - . Figure 2-5 General Playfield Description . Figure 26 Double Breakout Play Mode... . Figure 2-7 Cavity Breakout Play Mode... . . . be oe Figure 2-8 Progressive Breakout Play Mode....... . Figure 2-9 Progressive Breakout Scrolling Effect . . . Figure 2-10 Diagram of Ball Rebounds Off Paddle .. . . Figure 3-1 Super Breakout Game Block Diagram. . . Figure 3-2 Super Breakout PCB Block Diagram . . Figure 3-3. Super Breakout Schematic Diagrams .. . Figure 3-4 — Power Supply Simplified Block Diagram . . Figure 35 | Memory Block Diagram ............. Figure 36 — Phase 1 and Phase 2 Signal Shaping . . Figure 3-7 Simplified Diagram of Crystal-Controlled Oscillator and TV Sync Circuitry Figure 3-8 — Horizontal Sync Timing Diagram Figure 3-9 Vertical Sync Timing Diagram. . bees Figure 3-10 Playfield Generator Block Diagram... . Figure 3-11 Charactor Display Data................ Figure 3-12 Address Multiplexers Equivalent Diagram : 3-12 Figure 3-13 Motion Generator Circuit, Simplified Diagram . .. . 3-13 Figure 3-14 Significant Paddle Signals and Timing... . . 314 Figure 3-15 Super Breakout Harness Schematic Diagram ...... . nn 2 Figure 3-16 Coin Door Schematic Diagram . ee Figure 3-17 Type B Power Supply Schematic Diagram . Figure 4-1 Coin Door Assembly................65 Figure 42 Hinging Open the Magnet Gate Assembly Figure 4-3. Removal of Coin Mechanism ........ Figure 44 — Surfaces to Clean Inside the Coin Mechanism . Figure 45 — Removal of Plate Covering Rear of Coin Slot Figure 46 — Close-up View of Lubrication Point Figure 47 Detail View of Coin Switch and Trip Wire Figure 48 — Adjustments on Coin Mechanism . Figure 49 Locations of Adjustments on TV Chassis. Figure 410 TV Monitor Removal........ Figure 411 Lamp/Speaker and Fluorescent Lamp Removal ee

Super Breakout v

Page 8

LIST OF ILLUSTRATIONS

Figure 4-12 LICON (LED) Serve Switch Removal ...................-- Figure 4-13 Lamp Start Switch Removal .. Figure 4.14 Paddle Control Removal .... Figure 4-15 Game Select Removal . . Figure 5-1 Final Cabinet Assembly Figure 5-2 TVShelf Assembly ....... Figure 5-3 Control Panel Assembly Figure 5-4 Coin Door Assembly . Figure 5-5 Front Bezel Assembly . Figure 5-6 Coin Lockout Assembly .. . Figure 5-7 Coin Switch Assembly... ... . . Figure 5-8 Type B Power Supply Assembly ........... : Figure 5-9 Fluorescent Light and Speaker Mount Assembly . Figure 5-10 Fluorescent Light Assembly ..................-. Figure 5-11 RF Shield PCB Assembly Figure 5-12 Start Button Assembly........ Figure 5-13 Super Breakout PCB Assembly ... .

vi Super Breakout

Page 9

Table 1-1 Table 1-2 Table 1-3 Table 2-1 Table 2-2 Table 2-3 Table 3-1 Table 3-2 Installation Requirements ....... Operator Options. . . Self-Test Procedure . tee Double Breakout Scoring Chart . . . Cavity Breakout Scoring Chart . . . Progressive Breakout Scoring Chart MPU Input/Output Signal Descriptions Atari Inc. Programmable Memory Map . . .

LIST OF TABLES

Super Breakout vii

Page 10

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 11

A. INTRODUCTION

Super Breakout™ is a one- or two-player game developed by Atari Inc. The game is packaged in an upright, floor-resting cabinet illustrated by brightly colored orange, red and white graphics to further enhance potential play. A 19-inch TV monitor is mounted vertically in the top front of the cabinet. The TV monitor viewing screen is shielded by a Plexiglas® panel that also displays colorful graphics.

Player-operated controls are mounted on a control panel directly below the TV monitor viewing screen on the front of the game cabinet as illustrated in Figure 1-1. The controls consist of a Game Select rotary switch, paddle control knob, a red LED serve pushbutton and a one-player start and two-player start pushbutton.

LOCATION SETUP

Super Breakout

Page 12

SERVE LED PUSHBUTTON

PADDLE CONTROL KNOB

GAME SELECT ROTARY SWITCH

ONE-PLAYER START PUSHBUTTON

TWO-PLAYER START PUSHBUTTON

CONTROL PANEL

Figure 1-1 Super Breakout Control Panel

The coin mechanism on the front mid portion of the game cabinet, below the control panel, initiates the play. The cash box is located behind a locked access door.

Super Breakout is a ball-and-paddle game; the player’s objective is to build up the highest possible point score by hitting the balls toward a wall of bricks, regardless of the game selection. Each time a ball hits a brick, points are added to the player's score. The brick disappears and the ball rebounds. Player accumulated scores are displayed continuously at the bottom of the TV screen. Besides rebounding from the bricks and from the player’s paddle(s), the ball also rebounds from the two sidewall boundaries and from the backwall boundary behind the wall of bricks.

B. GAME INSPECTION Your new Super Breakout game is manufactured ready to play on removal from the shipping carton. Your cooperation is desired in order to supply the firal touch of quality control to your game. Please follow the procedures below to ensure that your game is in perfect condition:

  • Examine all external parts of the game cabinet for dents, chips or broken parts.

1-2 Super Breakout

  • After determining that the game has been received in good condition, unlock and open the rear access door. Carefully inspect the interior and verify the following: a. All plug-in connectors are firmly seated. b. Remove game PCBas instructed in Steps 1-4 of Section E.

c. All integrated circuit packages (chips) in sockets on the game printed circuit board are firmly seated.

d. Replace game PCB as instructed in Step 6 of Section E.

e. The fuses are all seated snugly in their holders. f. No harness wires are disconnected.

g- No loose foreign objects should be present, especially metal objects that could cause electrical problems.

Be sure all major assemblies are checked. Check the game printed circuit board (PCB), the transformer (located on the power supply chassis), the speaker, fluorescent lamp and al! other player controls. Also be certain that the TV monitor is securely mounted.

Page 13

LINE VOLTAGE VOLTAGE-CHANGING PLUG WIRE COLOR

8 Amp, 125v. Fast - Blow $5 VAC BLACK

installed at factor:

220 VA

ORANGE CONNECTOR (FACTORY- INSTALLED) VOLTAGE SELECTION CONNECTOR

2.5 Amp.125 V. Slow —blow ON/OFF AND C4 INTERLOCK

la SWITCH

3Amp, 250 v. POWER SUPPLY Slow - blow CHASSIS.

Figure 1-2. Voltage-Selection Connectors

Check the serial number located on the metallic label in the upper left-hand corner on the back of the game cabinet. This serial number also appears in the corner (common to both edge connectors) on the back of the PCB, inside the game cabinet. See the illustration on the inside front cover of this manual.

  • If AC line voltage is consistently below 100 VAC, plug in the black low-voltage connection, on the Power Supply Chassis.*
  • IfAC line voltage is approximately 110 VAC, plugin the orange connection (factory installed).

C. INSTALLATION IF YOUR LOCAL LINE VOLTAGE IS NOT 110 VAC,

REQUIREMENTS BUT INSTEAD IS 220 VAC, perform the following

steps: Voltage Selection Your Super Breakout game is shipped for opera- 1. Measure AC line voltage with an AC voltmeter. tion at 110 VAC, 60 Hz.

  • If AC line voltage is consistently below 210 VAC, IF YOUR LOCAL LINE VOLTAGE IS 110 VAC, per- plug in the green low-voltage connection.* form the following steps:
  • IfAC line voltage is approximately 220 VAC, plugin
  • Measure AC line voltage with an AC voltmeter. the red connection.

*Figure 1-2 shows the four connectors with one of them already plugged in. Super Breakout 1-3

Page 14

Table 1-1 Installation Requirements

Power Requirements Power Supply: 110 VAC @60 Hz 220 VAC @50 Hz 200 Watts

Temperature Range On Locationand No lower than 0 degrees Celsius In Storage: (32 degrees Fahrenheit) No higher than 49 degrees Celsius (120 degrees Fahrenheit)

Humidity Range Relative »

Humidity: No more than 95%

Location Space Requirements * Height: 169 centimeters (66 inches) Width: 62 centimeters (25 inches) Depth: 70 centimeters (28 inches) TV Monitor 19-inch Black and White

*See Figure 1-3. Type of Power Cord Atari has added a strain-relief cord to your Super Breakout game. The advantage of this type of cord is that if pulled accidentally, the strain relief will hold the cord in place at the cabinet wall. The plastic strain relief ‘‘cushions’’ the impact of the shock and prevents the cord from pulling the wires out of the harness connector.

D. INTERLOCK, POWER ON/OFF SWITCH AND OTHER OPERATOR CONTROLS To minimize the hazard of electrical shock while you are working on the inside of the game cabinet, two interlock switches have been installed. One is located behind the rear access door and one behind the coin door. These switches remove all the power from the game cabinet while the doors remain open. To help conserve energy, a power on/off switch has been placed on the game so that it can be turned off during closed periods. This switch is located in the

C3

(169 CENTIMETERS)

R Bas, (70 CENTIMETERS)

(62 CENTIMETERS)

Figure 1-3 Location Set-up Requirements

1-4 Super Breakout

Page 15

POWER ON/OFF SWITCH

NOTE: WHEN TROUBLESHOOTING WITH THE DOOR (S) OPEN, YOU MUST PULL INTERLOCK INTERLOCK SWITCH PLUNGER OUT WITH THUMB AND FOREFINGER AS INDICATED BY DIRECTION OF ARROW.

Figure 1-4 Location of Interlock and Power On/Off Switches

upper rear left-hand corner of the game cabinet, as 3. Set the power on/off switch to the ‘on’ position. shown in Figure 1-4.

  • Close the rear access and coin door. Within approximately 30 seconds after closing the last door to the game cabinet the TV monitor should display Interlock Switch Checkout Procedure Check for proper operation of the interlock switches by performing the following steps: a picture.
  • Unlock and open the rear access door and the coin door. 5. Slowly open either door to the game cabinet, and the TV picture should reappear, when either the
  • Plug the AC power cord into your local line AC rear access or coin door is opened to approxioutlet (110 VAC or 220 VAC). mately one inch.

Super Breakout 1-5

Page 16

Table 1-2 Option Settings

Switch Settings on 8-Toggle DiP Switch (located at position J8/9 on the Game PCB) OPTION RESULT 1 2 3 4 5 6 7 8

Game instruction language | ON ON English

(as displayed onON OFFGerman
TV screen)OFF ONFrench

OFF OFF Spanish

Coin Mode ON ON Free play ON OFF 2 Plays/Coin OFF ON 1 Coin/Play OFF OFF 2 Coins/Player

Game Length ON 5 Balls OFF 3 Balls

Extended Play LevelsProgressiveCavityDouble
(extended play equalsBreakoutBreakout _ Breakout
one full game)ON ON ONNo extended play allowed
ON ON OFF200200200
ON OFF ON400300400
ON OFF OFF600400600
OFF ON ON900700800
OFF ON OFF12009001000
OFF OFF ON160011001200
OFF OFF OFF200014001500
  • If the results of Step 5 are satisfactory, the interlock switches are operating properly. Ifthe picture does not disappear as described, check to see if the corresponding interlock switch is broken from its mounting or stuck in the “on’”’ position.
  • Close and lock both doors.

E. OPERATOR OPTIONS The operator options offer maximum player appeal for each game location. These options are listed in Table 1-2. They are preset for a certain game set-up during production. To determine how the switches have been set for the game, compare the attract mode with the information in Table 1-2.

To change the toggle positions of the switch assembly and set the desired options, the printed circuit board (PCB) must be removed according to the following procedure:

1-6 Super Breakout

NOTE This game includes a new style of easyaccess PCB. The radio frequency shield has been redesigned to use only three individual quarter-turn fasteners as a direct result of field input.
  • Unplug the game power on/off switch and open the rear access door.
  • Locate the radio frequency (RF) shield board assembly immediately inside the game cabinet behind the rear access door (see Figure 1-5). On one end of the assembly is a small PCB with an edge connector coming from the edge of the Super Breakout game PCB. (The RF Shield Assembly is an aluminum box with hundreds of holes.)
  • Turn the three individual quarter-turn fasteners on the RF Shield assembly %-turn to the left, or counterclockwise.
Page 17

GAME PCB

Ya-TURN FASTENERS

Figure 1-5 Option DIP Switches and Game PCB Location and Removal

Super Breakout 1-7

Page 18

VOLUME DECREASE: COUNTER- CLOCKWISE

SELF-TEST-SWITCH

VOLUME CONTROL

Figure 1-6 Location of Self-Test Switch and Volume Control

  • Carefully pull out the Super Breakout game PCB and the RF Shield board together as a unit. These would not normally need to be separated when making option switch changes.
  • Set the switches for the desired options, as listed in Table 1-2.
  • Reinstall both PCBs by following steps 1 through 4 in reverse order. Do not force or bend the game PCB. Before reinstalling, always inspect the game PCB for damage.

N Close and lock the rear access door.

  • Plug in the game and verify that all options function by playing the game.

1-8 Super Breakout F. SELF-TEST PROCEDURE Super Breakout will test itself and provide data to demonstrate that the game’s circuitry and controls are working properly. This procedure uses the TV monitor and the speaker; no additional equipment is required. See Figure 1-6 for location of the Self-test switch. To start the procedure, slide this switch to on as indicated in the figure. See Table 1-3 for further details and instructions on the self-test. We suggest that you run the self-test each time the coin box is opened.

G. VOLUME CONTROL If volume is incorrect for your location, open the coin door and adjust the volume control as indicated in Figure 1-6.

Page 19

Table 1-3 Self-Test Procedure

Instruction Result if Test Passes Result if Test Fails

  • Preliminary | Set volume level potentiometer Not Applicable Not Applicable (located on a bracket immediately behind and to the left of the coin door) to % volume. |
  • RAM Test Set Self-Test Slide switch Clears the Screen The TV monitor screen displays a (located above the volume pattern, and a series of eight tones potentiometer, immediately (representing DO through D7 behind and to the left of the respectively) sound off. coin door) to the“on” position. A distinct LOW tone indicates a good bit. A HIGH tone indicates the bit is different from what it should be. The test stops (video, no audio) until the self-test switch is turned to “off”, and then back on again.
  • ROM Test
No operator action required.|When ROMs 0, 1,2, 3, and 4When ROMs0, 1,2,3, and 4do not

checksum correctly no message | checksum, a message is displayed

Immediately follows instruc-_|is displayed on the TV screen.on the TV screen to indicate the

tion 2 if it passes. This step failed ROM number. It also indiautomatically tests ROMS 0, 1, cates the difference between 2,3, and 4 that represent five obtained value and the expected 1K byte blocks. value, in a 2-digit hexadecimal number.

  • Lights and Audio Test Operator should adjust volume |The one- and two-player start Lights do not turn on. control. lights and the serve light light up. | Proceed to instruction 5.
Immediately follows instruc-|Four audio tones are alsoEither no tones or missing tones.

tion 3 whether or not it passes. {sounded (from high to low tone).

  • Switch and Lamp Test Immediately follows instruction 4 whether or not it passes.

Rotate Paddle Knob

Push all the following switches: SLAM, COIN SWITCHES, PLAYER START SWITCHES, SERVE SWITCH, GAME SELECT KNOB. Paddle control potentiometer remains displayed. All lights remain lighted. All values from 00 to FF hexadecimal notation should be obtainable. Any movement of the knob should cause the numbers on the screen to move not more than 1 digit in either direction.

Each pressed switch generates audible click. No potentiometer values displayed, and any one or several lights turn off. Values not between 00 and FF. Possibility potentiometer too noisy as a result of a dirty pot.

Neither a click or any sound.

Super Breakout

Page 20

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 21

GAME PLAY

A. INTRODUCTION The Super Breakout game has three different modes of operation. These modes are listed and described below:

© ATTRACT—-When power is applied or as a result of a game ending with no further credits.

@ READY-TO-PLAY—Coins accepted.

© PLAY—Initiated immediately after pressing the one- or two-player start button.

Super Breakout

Page 22

Super Breakout allows the player(s) to select any one of three different action-packed Super Breakout games by turning the game select knob on the control panel to the desired game. The three available Super Breakout games are the following:

© Double

© Cavity

© Progressive

Each game play is explained in later paragraphs under Section D.

B. ATTRACT MODE (Sce Figure 2-1)

The Attract mode appears in two different versions. The first version occurs immediately after AC power-up of the game or after Self-Test. The second occurs at the end of every game when there is no longer any credit. The difference between these two attract mode versions is appreciable and must be noted.

The first version of the attract mode (power-up) begins when AC power is applied to the game and the power on/off switch is tured “on” (the power switch is located at the top rear of the cabinet as shown in Figure 1-4).

While in the first version of attract mode, the TV monitor displays each game sequentially, beginning with Cavity, for a short time. It then proceeds to Double, to Progressive, and finally returns to Cavity. The screen does not display a paddle but rather an invisible solid line at the bottom of the TV screen (where the paddle normally is displayed).

Immediately upon applying AC power to the game, the first attract mode version is activated anda ball is automatically served. When the ball is served it randomly heads toward the horizontal line; on impact with this line the ball rebounds, then travels towards the brick wall. The ball hits a brick, the ball rebounds and the brick disappears but the serve does not change as a result of having a solid invisible row of paddles that never miss. This continuous rebound action proceeds as the playfields change from Cavity, to Double, to Progressive and back to Cavity, drawing the attention of a passing potential player. In this attract mode version the last two player scores remain steadily displayed at the bottom of the TV monitor screen, whereas the coin/player credit phrase is displayed blinking at the bottom of the screen.

2-2 Super Breakout phrase is displayed blinking at the bottom of the screen.

The sound (or audio) remains muted during the attract mode and neither the one- or two-player start pushbuttons or Serve pushbutton is lighted. These switches and the 3-position rotary switch also remain inoperative during this version of the attract mode.

The second version of the attract mode occurs at the end of every game when there are no longer any credit. When the last ball in the game is served and missed, the second version of the attract mode appears and displays the last game’s brick pattern (if any). The paddle(s) disappear, leaving the solid invisible horizontal row of paddles and a flashing coin mode on the screen (corresponding to the operator's option setting), alternating with High Score (if not zero). The required number of balls for the game being displayed are then served and captured to randomly bounce against the playfield objects and boundaries, but never to leave the screen or knock out any bricks until the player adds more credit to the game.

NOTE The game select rotary switch remains i operative until credits are provide

After several seconds lapse, the first version attract mode appears on the screen as described in previous paragraphs under this heading.

C. READY-TO-PLAY MODE (See Figures 2-2, 2-3, 2-4) The ready-to-play mode exists for each game selection as illustrated in Figure 2-2 (Cavity), Figure 2-3 (Progressive), and Figure 2-4 (Double). This mode is immediately initiated after the coins are accepted by the coin mechanism or at the end of a game with credits remaining. After the coins are accepted, the rotary game select switch becomes active and the screen changes from its current attract mode playfield display sequence to the playfield corresponding to the game select switch setting. For example, if the screen displays a Double Breakout while in the attract mode and the game select switch was set to either Cavity or Progressive, the display would immediately change from the attract mode Double game playfield to the Cavity or Progressive ready-to-play mode playfield. During the ready-to-play mode the paddle(s) become visible and the ball is no longer automatically served.

Page 23

SCREEN DISPLAYING DOUBLE BREAKOUT PLAYFIELD

ORANGE BRICKS

GREEN BRICKS

FLASHING SS —— == SS Se INVISIBLE ROW OF =>1COIN 1PLAYER PADDLES

PLAYER ONE PLAYER TWO SCORE SCORE

VERSION ONE

Figure 2-1 Attract Mode

Super Breakout 2-3

Page 24

SCREEN DISPLAYING DOUBLE BREAKOUT PLAYFIELD

ORANGE BRICKS

GREEN BRICKS

BALL

INVISIBLE ROW a OF PADDLES

HIGH SCORE 2100 ALTERNATELY FLASHES WITH THE COIN MODE

(1 COIN 1 PLAYER)

PLAYER ONE PLAYER TWO SCORE SCORE

VERSION TWO

Figure 2-1 Attract Mode

2-4 Super Breakout

Page 25

BALLS

ORANGE (MOTIONLESS)

BRICKS

GREEN BRICKS

PADDLE

BONUS FOR 1400 = 1COIN: 1PLAYER<= 06 12 FLASHING

SERVE BUTTON DOES NOT FLASH

CONTROL PANEL

ONE-PLAYER TWO-PLAYER

START BUTTON START BUTTON FLASHES FOR ONE FLASHES FOR TWO COIN CREDIT COIN CREDITS

Figure 2-2 Cavity Breakout Ready-to-Play Mode

Super Breakout 2-5

Page 26

BLUE BRICKS

GREEN BRICKS

BONUS FOR 200 PADDLE =< -

1COIN 1PLAYER

A144 FLASHES ALTERNATE WITH “HIGH SCORE 1144” SERVE BUTTON LIGHT DOES NOT FLASH.

CONTROL PANEL

ONE-PLAYER TWO-PLAYER START

START BUTTON BUTTON FLASHES FOR FLASHES FOR TWO COIN CREDITS ONE COIN CREDIT

Figure 2-3 Progressive Breakout Ready-to-Play Mode

2-6 Super Breakout

Page 27

ORANGE

GREEN BRICKS

=.

BONUS FOR 1500 PADDLES

SERVE BUTTON LIGHT DOES NOT FLASH

CONTROL PANEL

ONE-PLAYER TWO-PLAYER START BUTTON START BUTTON FLASHES FOR ONE FLASHES FOR TWO COIN CREDIT COIN CREDITS

Figure 2-4 Double Breakout Ready-to-Play Mode

Super Breakout 2-7

Page 28

DOUBLE BREAKOUT EXAMPLE

BACKWALL

ORANGE BRICKS

GREEN BRICKS

SIDEWALL

PADDLES

SECOND BALL SERVED (SERVE IS NOT LOST IN THIS CASE)

SERVE INDICATOR WHEN FIRST BALL INDICATES SERVED IS MISSED, BALL TO THE SERVE IS LOST BE SERVED AND SERVE INDICATOR (WHEN TWO BALLS COUNTS UP ONE ARE SERVED AT THE COUNT SAME TIME, THEY ARE STILL COUNTED AS ONE SERVE

2-8 Figure 2-5 General Playfield Description

Super Breakout

Page 29

The screen also displays point requirements for bonuses (operator option), and the player or players have the option of selecting a desired game. The one-player start pushbutton flashes when only one credit has been accumulated. Both buttons flash when two or more credits have been accumulated. The Licon LED serve pushbutton switch remains off (unlighted and inoperative) until either the one- or two-player start pushbutton is pressed.

The game's circuitry has a credit accumulator that can keep track of up to 15 game credits. One credit is subtracted from the accumulator at the beginning of a one-player game, and two credits are subtracted at the beginning of a two-player game. Just after initial application of AC power, the deposit of coins will cause credits to be added. An operator option can be set so that deposit of one coin adds one credit, or else so that it adds two credits. During the first and subsequent play sequences, one credit will also be added each time a player attains the preset bonus score level, provided that a second operator option has been set to allow bonus credits. The game's two start pushbuttons are engraved with the words “One-Player Start” and “Two-Player Start”. The lamp behind the one-player button flashes whenever at least one credit is remaining in the credit accumulator, and behind the two-player button whenever at least two credits are remaining, and the program is waiting for the player(s) to push one of these buttons.

D. PLAY MODE After the ready-to-play mode is displayed, as discussed in the previous paragraphs, the player(s) may select a game by simply setting the game select rotary switch to the desired setting. Either player start switch initiates the play mode for the selected game whenever pressed. The serve lamp begins to flash and the current PLAYER’S SCORE flashes at the bottom of the TV screen. Before the serve switch is pressed for the first time, the player(s) still has the option of changing the game by turning the game select switch. The bonus score needed will be displayed, but the high score will not be displayed.

The play modes of all three selectable games are explained in detail in the following paragraphs.

The ball’s initial direction will be random (see Figure 2-5). Although one component of its direction will always be toward the paddle rather than toward the bricks, the ball may even hit a sidewall boundary before it reaches the paddle end of the screen. The ball is never allowed to move in a direction exactly perpendicular to the front surface of the paddle, the bricks or to any of the boundaries. As soon as the first ball appears, the serve buttons go dark (turn off), but the batl number in the mid-lower portion of the screen remains at ‘1’. On subsequent serves, however, the number will be increased by 1 each time a new ball appears on the screen.

With the ball moving on the TV screen, the player must now try to volley, that is, try to manipulate the paddle knob so that the paddle will move to a position that intercepts the ball before it escapes off the screen. If the player succeeds, the ball will rebound off the wall of bricks. The “blip” sound will be produced whenever the ball hits the paddle, and the “bounce” sound whenever the ball hits a boundary. Whenever the ball hits a brick, that brick will disappear and the ball will rebound. But only one brick can disappear at a time. A “tick” sound is produced to represent each point of the brick’s score point value.

A serve ends right after the player fails to volley; the serve button lights up and flashes as soon as the ball has disappeared off the end of the screen. To continue the play sequence a player must again depress the serve button. During two-player games the flashing score in the lower left corner of the TV screen changes from the left (player one) to the right (player two) after player one misses a volley, and vice versa when player two misses a volley. Each player in a two-player game receives an equal number of serves. (The game resets the respective player's last position in a two-player game.)

The play sequence continues as described above until all the balls are served. If no credit is remaining in the credit accumulator at this time, then the game reverts back to the attract mode, version two. But the game will remain in the play mode if one (or both) start buttons are lighted, because this means that credit is remaining in the credit accumulator. After the game reverts to the attract mode, version two, it automatically serves itself a ball. This ball cannot escape, however, because it cannot get past the invisible solid row of paddles at the lower end of the TV screen.

Double (See Figure 2-6) The Double Breakout game is selected by setting the Game Select rotary switch to “Double.” The player then presses the flashing player start pushbutton and serves the ball whenever desired by pressing the flashing red LED serve pushbutton.

Super Breakout 2-9

Page 30

ORANGE BRICKS

GREEN BRICKS

SECOND BALL SERVED

FIRST BALL SERVED

PLAYER TWO SCORE FLASHES IS NOT DISPLAYED WHENEVER IF ONLY THE PLAYER ONE ONE-PLAYER IS UP START BUTTON IS PRESSED. WHEN THE TWO-PLAYER START HAS BEEN PRESSED, THIS SCORE IS DISPLAYED AND WILL FLASH CONTROL PANEL WHENEVER PLAYER Two IS UR SERVE BUTTON STOPS FLASHING WHEN PRESSED ONE- AND TWO-PLAYER START BUTTONS STOP FLASHING AFTER BEING PRESSED (EITHER ONE)

Figure 2-6 Double Breakout Play Mode

2-10 Super Breakout

Page 31

Before serving the ball, the double breakout playfield contains 52 orange bricks (4 x 13) at the top of the TV screen and 52 green bricks (4 x 13) immediately below the orange brick wall. The upper two rows of orange bricks are worth 7 points, when struck by a ball, 5 points for the lower two orange rows, 3 points for the upper two rows of green bricks and 1 point for the lower two rows of green bricks. See Table 2-1 for a quick and easy scoring reference. The maximum score for Double Breakout is 2694.

Table 2-1 “Double” Breakout Scoring Chart

brick 1 Ball 2 Balls Color Row in Playfield } in Playfield

orange1714
orange2714
orange3510
orange4510
green536
green636
green712
green812

Two paddles are displayed at the bottom end of the TV screen. When the serve pushbutton is pressed two balls are served. Ifthe first ball served is missed, it counts as a missed serve and goes against the players allotted serves per game; otherwise the second ball is served. If the second ball served is missed after striking the first served ball, the player may continue with the first ball. Each brick knocked out scores according to the last two columns of Table 2-1, depending on how many balls are in the playfield. Either ball may be hit with either paddle, and they will not bounce off the bottom of the upper paddle.

Cavity (See Figure 2-7) The Cavity Breakout game is selected by setting the game select rotary switch to “Cavity.” The player then presses the flashing player start pushbutton. The ball may be served whenever desired by pressing the flashing red LED serve pushbutton.

Before serving the ball, the Cavity Breakout playfield contains 44 orange bricks and 52 (4 x 13) green bricks located immediately below the orange brick wall. At approximately 3 columns in and 2 rows down into the orange brick wall, from both the left and the right of the wall, two cavities exist. These two cavities occupy the space of 4 bricks (a 2 x 2 brick area). Each cavity contains a captive ball that remains motionless prior to serving the ball. When the ball is served, these captive balls bounce inside the cavity, until the ball is missed. In this case they stop moving, and remain motionless once again until the next ball (if any) is served. As long as the balls remain captive, the bricks surrounding them do not disappear when struck by them, and no points can be accumulated from these balls.

Each brick in the upper two rows of the orange brick wall are worth 7 points when struck by a ball, 5 points for each brick in the lower two orange rows, 3 points for each brick in the upper two green rows and only 1 point for each brick in the lower two rows of green bricks (see Table 2-2).

One paddle is provided in this game, and only one ball is served, unlike Double Breakout. When enough bricks are removed to release a captive ball from its cavity, the score doubles for each brick hit by any one of the two balls in the playfield (as long as the served and freed ball remain active in the playfield). If the third ball is freed, all three balls are played in the playfield, the score triples. If any one of the balls is missed and lost, the score returns to double points. If the second ball is missed and only one ball remains in the playfield, points are then scored as listed under the 1-ball column of Table 2-2.

The maximum score attainable for Cavity Breakout is something less than 3384.

Table 2-2 “Cavity” Breakout Scoring Chart

1 Ball 2 Balls 3 Balls

Brickininin
ColorrowPlayfield | Playfield | Playfield
orange171421
orange271421
orange351015,
orange451015
green5369
green6369
green7123
green|8123

Progressive (See Figure 2-8) The Progressive Breakout game is selected by setting the game select rotary switch to “Progressive.” The player then presses the flashing player start

Super Breakout 2-11

Page 32

CAVITIES: BALLS IN MOTION

ORANGE BRICKS

GREEN BRICKS

PLAYER TWO SCORE iS NOT DISPLAYED

FLASHES IF ONLY THE

WHENEVER ONE-PLAYER BUTTON IS PRESSED. WHEN THE TWO-PLAYER START BUTTON HAS BEEN PRESSED, THIS SERVE BUTTON SCORE IS DISPLAYED STOPS FLASHING AND WILL FLASH WHEN PRESSED WHENEVER PLAYER TWO Is UP PLAYER ONE iS UP

CONTROL PANEL

NE AND TWO PLAYER

START BUTTONS STOP FLASHING AFTER BEING PRESSED (EITHER)

Figure 2-7 Cavity Breakout Play Mode

2-12 Super Breakout

Page 33

SERVED BALL

FLASHES WHENEVER PLAYER ONE IS UP.

BLE AVITY. PRO

SERVE BUTTON STOPS FLASHING WHEN PRESSED. CONTROL PANEL

ONE- AND TWO- PLAYER START BUTTONS STOP FLASHING AFTER BEING PRESSED. BLUE BRICKS

GREEN BRICKS

PLAYER TWO SCORE IS NOT DISPLAYED IF ONLY THE ONE PLAYER BUTTON IS PRESSED. WHEN THE TWO-PLAYER START BUTTON HAS BEEN PRESSED, THIS SCORE IS DISPLAYED AND WILL FLASH WHENEVER PLAYER TWO IS UP.

Figure 2-8 Progressive Breakout Play Mode (Not Yet Scrolled)

Super Breakout 2-13

Page 34

DIRECTION OF SCROLL

BLUE AREA

YELLOW AREA

WHEN THE BALL IS MISSED AND SERVED AGAIN, THE ROW OF BRICKS CLOSEST TO THE PADDLE DISAPPEARS AS THE ENTIRE PICTURE SCROLLS DOWN ONE ROW. BLUE PADDLE

Figure 2-9 Progressive Breakout Scrolling Effect

2-14 Super Breakout

Page 35

pushbutton. The ball may be served whenever desired, by pressing the flashing red LED pushbutton.

Before serving the ball, the Progressive Breakout playfield contains two 4 X 13 brick walls (one blue and the other green). The blue brick wall, which consists of 52 bricks, is atthe top. Then occurs a space equivalent to this wall. In the middle of the screen is a green brick wall consisting of 52 bricks.

The brick walls move or “scroll” toward the paddle at a rate determined by the number of hits on the ball. As the bricks are knocked out and the walls progressively creep up on the player’s paddle, new bricks enter the playfield at a progressively faster rate; four rows of bricks are always separated by four rows of blanks.

As the brick walls scroll down, their colors change (see Figure 2-9) which indicates a new point score for that brick at that instant of time. There are four different colors of bricks, each color with a different score value. The blue bricks are worth 7 points when struck by the ball, 5 points for each orange brick, 3 points for each green brick and 1 point for each yellow brick. See Table 2-3 for a quick and easy reference. Bricks that scroll off the bottom of the screen are lost and are not counted toward or against the player's score.

Table 2-3 Progressive Breakout Scoring Chart

Color Points per Brick

blue 7 orange 5 green 3 yellow 1

The maximum attainable score for progressive Breakout is infinite.

Ball Speed Besides the slowest ball speed already described (right after the serve), there are three possible speed-ups. The first speed-up after the serve occurs on the 4th hit, and a second faster speed-up occurs on the 8th hit. The third occurs after the 12th hit and the fourth occurs when a highpoint (either a 5- or 7-point) brick is hit, regardless of previous speed. Ball speed is restored to the slowest value at the beginning of each serve. Ball Direction When the ball intercepts the paddle it will rebound in any of four directions, depending on which portion of the paddle was hit (see Figure 2-10). This is still the case after the paddle has been reduced to half its normal size. Note that the ball is not allowed to move ina direction perpendicular to the front surface of the paddle or perpendicular to the edge of the paddle. These directions change with the number of hits of the ball, just like the ball speed changes occur at the 4th, 8th and 12th ball hits.

BALL DIRECTIONS

LZ | ravbue

NOTES: 1, Angle of rebound is determined by which portion of the paddle that the ball hits. The bail’s angle of incidence is irrelevant. . The angles of rebound become more perpendicular as ball speed increases. . The diagram above, with four sections, still applies after paddle width has been reduced to half the normal value.

Figure 2-10. Diagram of Ball Rebounds off Paddle

The player must hit the ball first, otherwise bricks cannot be knocked out, and the ball will pass through all the bricks in its path. The ball with also pass through any bricks if it has not gone at least four rows from the last brick hit, and not hit the paddle or the uppermost boundary at the top of the screen.

Immediately on hitting the uppermost boundary at the top of the screen the paddle(s) will reduce to half its width until the next serve if any.

Page 36

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 37

A. GENERAL INFORMATION This chapter provides a general overview of the theory of operation of the Super Breakout electronics contained on the game printed circuit board (PCB). It also goes into specific detail of the various circuits to explain to an individual of moderate technical background how these circuits should perform. This detailed information has been organized with emphasis placed on troubleshooting the game PCB, circuit by circuit.

The Super Breakout game block diagram of Figure 3-1 illustrates the major components, including all controls remote to the game PCB. The function and direction of the information to and from these various controls is also shown.

The Super Breakout PCB block diagram in Figure 3-2 illustrates the division and function of the various circuits located on the game PCB and how they are controlled by the microprocessor. Refer to Figure 3-2 as you go through the following circuit descriptions.

Super Breakout

Page 38

CONTROL GiRCUTRY

‘Ag SOURCE

SPEAKER

Test

AL BRACKET LOCATED BEHIND THE COIN

DOOR (REFER TO FIGURE 1-6)

Figure 3-1 Super Breakout Game Block Diagram

3-2 Super Breakout

Page 39

MONITOR, GENERATOR

‘SOUND ‘AUDIO OUTPUT

GENERATOR ‘TO SPEAKER DISPLAY DOISPLAY 7

3-3 Super Breakout ‘COMP, VIDEO To

2 Super Breakout PCB Block Diagram Figure 3.

Page 40

The functional operation of the Super Breakout PCB circuitry begins naturally enough with the microprocessor (or MPU) circuitry. As you go through the various circuit descriptions, you learn how the MPU receives its sequential program insructions from its ROM memory and how it carries out these instructions through the use of its display RAM memory (Section C); how it reads in the game control switches (Section G), and how it writes or outputs the results of its instructions and calculations to the game’s other PCB circuitry, such as the playfield generator (Section £), the motion object generator (Section F), and the audio amplifier (Section K).

A circuit description of the standard Atari sync generator (Section D) is also included. This is the only PCB circuitry that functions independently of microprocessor control.

B. POWER SUPPLY (See Figure 3-3, Sheet 1 of 5 and Figure 3-5) The power supply produces all the necessary game voltage requirements as shown in Figure 3-4.

The PCB receives +10 volts DC, unregulated, at pins B and 2 of the game PCB edge connector; 16.5 VAC to pins C and 3 and D and 4; and 25 VAC to pins W and 19 and X and 20 from the secondary of the transformer located on the Type B power supply chassis.

The +10 volts is rectified and filtered off-board and regulated on-board by the LM323 three-terminal regulator device to a stable +5 volts DC. The +5 volts DC is distributed throughout the PCB to power all logic circuits. The 16.5 VAC is rectified on-board via diodes CR1 and CR2, filtered by capacitor C54 before being regulated by the 7905 to produce the —5 volts DC, required by the voltage comparator, LM319. The 25 VAC input is rectified through diodes CR3 and CR4 filtered by capacitor C55 and supplied as unregulated +20 volts to the TDA 1004 audio amplifier. This +20 volts is also regulated by a three-terminal device 7812 (Q8) to develop +12 volts DC.

C. MICROPROCESSOR CIRCUITRY (See Figure 3-3, Sheet 2 of 5) The heart of the Super Breakout game PCB is the microprocessor circuitry. A brief description of the

3-4 Super Breakout major components and their function within the microprocessor Circuitry is provided in the following paragraphs. Note that the microprocessor circuitry components include the following:

  • MPU (at location C3)
  • Address buffers (A2, B2 and C2)
  • Data buffers (E3, £4)

4, ROM memory (C1, Di and E/F1) for -04 version or PROM memory as listed in the PCB assembly parts list for the -03 version (refer to Illustrated Parts Catalog, Section 5).

  • RAM memory (F4, H4, J4, K4, F3, H3, J3, and K3)
  • Address decoding circuitry (E2, F2, D2, £8, and H8, and miscellaneous gates)
  • 0 clock driver (A7 and miscellaneous gates)
  • Watchdog reset counter (C6/7 and miscellaneous gates)

MPU, ROM, and RAM (See Figure 3-5) The microprocessor is the “master controller” behind all action that takes place in the game cir- Cuitry. In going through the following paragraphs refer to Table 3-1, MPU Input/Output Signal Descriptions. Upon initialization, the MPU (via AO-A15) addresses data permanently stored in the program ROMs or PROMs. This addressed data then travels to the MPU via its 8-bit data bus (D0 through D7). The MPU decodes this data to determine what action it is to perform next (i.e., “read coin switch 1,” “ball speed up,” etc.). The MPU uses RAM memory to perform many of these instructions, namely to temporarily store information which it will later recall. The MPU is capable of writing (or putting data into) the RAM and then later reading (pulling data out of) the RAM, via its address bus (A0-A15) and bidirectional data bus (D0-D7).

Address Decoding The MPU address decoding circuitry performs the critical function of turning on or enabling the appropriate game circuitry (i.e., RAM, ROM, latches, etc.) at the appropriate time, so that information can be transferred back and forth between this game circuitry and the MPU. A memory map defining the MPU circuit is shown in Table 3-2 as reference.

Page 41

+10 VDC (UNREGULATED)

‘AC SOURCE POWER n ‘SUPPLY \ CHASSIS. 16.5 VAC TO PADDLE CIRCUITRY COMPARATOR

REGULATOR CIRCUITS

Figure 3-4 Power Supply Simplified Block Diagram

RAM MEMORY BLOCK DIAGRAM

DISPLAY FROM ADDRESS [—— disPLay ~—) MOTION

MULTIPLEXERS CIRCUITS,

‘A0-9 RAM ‘AND SOUND 2, J2, H2 CIRCUITRY GENERATOR READ/WRITE MEMORY

' TO MPU ous o7/— ya a, ax 70 arena BUFFERED ’ DATA BUS. DATA BUS

ADR 0-9, PROM PROGRAM

BUFFERED MEMORY PROM 3-PROM 6 ENABLE

ADDRESS (12 MEMORY $7074 —Tenirs)—0s version To MPU ChIP EITHER/OR

PROGRAM UEMORY ROM 2, ROM 3, ROM4 ENABLE

To (3 ROM CHIPS) BIDIRECTIONAL DO VERSION MPU DATA BUS

PROM/ROM TO DISPLAY ROM,

Figure 3-5 Memory Block Diagram

0 Clock Driver (See Figure 3-6) The basic operating frequency of the microprocessor is established by its ®0 input (on pin 37 of the MPU device). The Super Breakout MPU runs at an operating frequency of 750 kHz. Examination of 1 ana ©2 (pins 3 and 39) waveforms with an oscilloscope should show two signals of opposite polarity with a period of 1.33 microseconds. (The period of any periodic waveform is the measurement of the time it takes to complete one full cycle.) The 750 kHz clock frequencies are derived from the 4H signal. This

Super Breakout 3-5

Page 42

Table 3-1 MPU Input/Output Signal Descriptions Description/Function Signal Description/Function These eight lines are bi-directional data bus lines. are loaded into the MPU program counter to point the start of a reset These sixteen lines are unidirectional routine. MPU address lines to supporting

memory (i.e., ROMs, RAMs) and I/O.NMIThis input line, while going low, indi-

cates a ““non-maskable interrupt” to the This input, when low, indicates an MPU. After the MPU concludes its interrupt to the MPU. After the MPU current instruction, it will then proceed concludes its current instruction it will to the NMI sequence.

proceed to the IRQ sequence.0Clock input

When low, this input line resets the .

MPU on either a power-up condition”1, @2Lhe linens non-overlapping MPU

ora Q, output of the watchdog counter. Clock outputs.

During the reset sequence prior toRWThis output is the read and write

RESET going high, the contents of two signal tine, which indicates the direction locations (FFFC, FFFD) in memory of data transfers on MPU data bus.

Table 3-2 Atari Inc. Programmed Memory Map NOTICE TO ALL PERSONS RECEIVING THIS ORAWING GONDENTIAL "Reprucion igcden itu Ihe sssued"and Pailoeie TEE Bs bata se atelier ole

eeMasethee ete ioemaniacurey tenao Wa hese
sa BonneeR= READfeniteense ng gh o reproduce ims srawing "granted
Az LOWEE ORDER APDRESS BVTSw= weiteThi welten bentason om the corporsion’ eee

ADDRESS DATA

resacccoad [A1SI8 [solSISISI* Ta l®PIEIS SS ETTSUNS Tick
0000-007 F} x]x]@]2 [o]o[o[ololalalalalalalaXI][RPK R(X 1X |X| X |] ZERO PAGE RAM

[osco-o774 |x| x[ololalalajalalalalalalalalal|x[[x[ x] x [x [x[x|x|x [|Video BSPLAY RAM oaze [[x[xlalel i [dlx|x|alali [afi lalofollel[olx|x|x|x|x{x[x[[secect 1 oaze |[x/x[d[dfr lo] x<]xfole[t loli [i] [alfel]ojx]x | x]x]x]x]x |] serve switca | 0830 x[x[ol dl [ox [x]o[a | [1 [BIS [ol [el[o lB] x |x [x [x [x |x [[ AnavaGe Sw OPTIONS Osa! xx {dla} [lx] xlala[i [i [olx fa]. [Jelfe fol |x|x][x |x |x []con mMope-sw OPTIONS 2832 |X| X|G/O]t [S| * |x] Slat | [S[K| 1 [wi el[o] x| «| x] x] x|x/x]] Soe S BALL- Sw OPTION Oe3t “XI lol [al x[xlaidfil il olx][ilolfel[xjolx|x|x]x}x]x]]Mse OF BONUS-SW OPTION casa |fxixlolol [ax x[alolt [i foie? [ie [ Blo x x |x| xx |x |[[CS& OF BONUS-Sw OPTION OB40 KxLXTAID] 1 [DL XX] PS] LX] X] Ki KI KIKI] [REY DLO] X| x] x] x] x] K || COIN SWITCHES caso |[x[x[alol [Olx[xl [A(x] x] [x] x] x]fef]o [x x[x]x|x] x [x]]2 PLAVER START SWITCH oeso |[|x]xlaloli [Ox] [ol x[x] x [x [x]x [TRI x] O/x lx) x] x [x [x] [1 PAYER START SwiTcH Seco [xl x|olal [a[xlelt [i [xlxlx]K[x [x] fe |D [x [x [x ]x[ «| |x | Seue vesT swercd

Oecex[x flo[ax fe fh[x xT X[x[X]x [Pe [x [Ofc[x [xf [x [Stam Swit

ocoe |[x|x lala] [i [alx[x[x[x[x[x[x}x]x [[e[[Djo|b] o[o]o[b |b] [veerican SYNC COUNTER ocio [ix[x[x[x[r[t[x[x]xfolofs [x|x[x [5 |[wl]x [x [x [x ]x]x]x |x|] seeve LED

oso_[[x[x]x}xli [i [xx [x [afi][x[x[xlol{wl]x]xlx{x][x]x [x ]x [one PUAvee START LIGHT

ocdo []x[x]x[x[t]t [x(x [x] [Ola] x] x] xD] wl] x |x} x] «1x [x] xe [] TWO PLAYER START LIGHT oeso [xxx fx[e [a [xfela ls ap [x(x [xo] fw] x [xx [x [x [Xx [x [SMT POT READING ENABLE Octo [[x/xfx[x[e lt [xP epee [i [efx [x[xfol[w [x] x(x [x] x] X[*[*][ Com couNTER

ocBoefelale {Te fetels |x [be abx bel ule x baba BslxWATCH DOG

Youo [{x[xlalt [o[ el x] «|x |x [x] Ix] [x] x] WI] [x |x] x]x]x]x |x [[ CSB OF POT READING “| 2coo-SFFEITX|x[ i [AJAJAJATATATAIATAIATAAIA/|R]/O/0/0/5/D]/D/D/D]] PROGRAM

O62FSatarast terehettetcsteretaretettsecees ©
S010x|[G[G|a|a[o|x[S[o/o] 1 [o[P]a]a][x|[D/D[o[o/p [D/ D/O] | Hoe ZONTAL BALL Pos:TION:
oonx[o[a[o[ala]x[dlalo]1 [sf ola}[[x{]x[x|«[x[D] D/O] 0} | Noise GENERATION BITS
oo[[x]x[@lo/o[dlo[xlolelols [1 [o]o|o[|x|[>[pJo|ojo [p/p|o}/veericaL BALL POSITION
|iklalelalalel=[alato Helex {fo Tx px [efx Pe [x [BACe PicTORE
  • O3= PROM -O4>ROM

3-6 Super Breakout

Page 43

«TULL

ne | AT pin 13

ee | J8 pin 10

ns J8 pin 9

oo ee ee C3 pin 37

o2 | C3 pin 39 a es C3 pin3

Figure 3-6 Phase 1 and Phase 2 Signal Shaping

4H frequency is generated by the horizontal sync counter P8, pre-shaped by latch A7, and buffered by driver J8 to produce the ©0 clock input. See Figure 3-7, Phase 1 and Phase 2 Signal Shaping.

Watchdog RESET The reset counter in the microprocessor control circuitry consists of a 4-bit decade counter, C6/7. The Q, output of this counter is the RESET signal to the MPU. Counter C6/7 counts how many times the 128V signal changes states. On every high-to-low transition of 128V, the counter advances to the next count in its sequence. Meanwhile, the TIMER RESET signal, generated by the MPU at various times during its normal instruction sequence, is resetting the counter back to zero. If for some reason the MPU program has strayed from its intended instruction sequence and the TIMER RESET signal does not occur before this counter counts up to a point where the Q, output goes high, a RESET signal is generated to the MPU. The RESET signal causes the MPU to restart its instruction sequence from the beginning of the program.

D. SYNC GENERATOR (See Figure 3-3, Sheet 1 of 5) The base frequency of the sync generator is a 12,096-MHz clock, generated by a crystalcontrolled oscillator consisting of crystal Y1, inverter N9, and several discrete components. The output of this oscillator is 12 MHz. Examination of this signal with an oscilloscope (at pin 8 of R9) should show the period (or cycle time) to be approximately 83 nanoseconds (.083 microseconds). See Figure 3-7.

This base frequency is then divided down by flip-flop R8 and binary counters P8 through N8: it provides the various horizontal synchronization frequencies (1H through 256H). The final output of this horizontal counter chain is 256H (at pin 11 of N8). This signal is in effect a division of the base frequency (12.096 MHz) by 768, to give a horizontal line frequency of 15,750 Hz. The period of 256H is about 63.5 microseconds. The 256H signal, as well as other horizontal signals, are used to generate the H BLANK and H SYNC timing pulses at flip-flop R1. See Figure 3-8, Horizontal Sync Timing Diagram for the relative timing of these waveforms.

The H SYNC signal is used to clock two stages of vertical sync counters (L3 and M3). This H SYNC signal is divided down by these counters to form the various vertical synchronization

Super Breakout 3-7

Page 44

VERTICAL SYNC

PULSES.

HORIZONTAL SYNC PULSES

qwazev ‘CRYSTAL: 12.096 MHz CRYSTAL. HORIZONTAL

SYNC

COUNTER

V BLANK

OSCILLATOR VERTICAL,

(N9, RO) (R8,P8,N8) V SYNC

VRESET

Figure 3-7 Simplified Diagram of Crystal-Controlled Oscillator and TV Sync Circuitry

3-8 Super Breakout

Page 45

ULL. Ee A pe pO ee ie ees ces OO es 128H }~<——_—_—_—_—_—_ 63.5 MILLISECONDS —____—_—_»| 256H PLAYFIELD DISPLAY wecank — MMMM HSYNC —_

Figure 3-8 Horizontal Sync Timing Diagram

LC 8V

16V

32V

64V

128V 16.3 MILLISECONDS ——_——> <1+____—\— PLAYFIELD DISPLAY VBLANK

VBLANK

VSYNC

VRESET

Figure 3-9 Vertical Sync Timing Diagram

frequencies (1V through 128V), These two stages of vertical counters are used, in effect, to do a divide by 262 of the H SYNC signal. This results in the final output of these counters (128V at pin 11 of M3) to be a signal at a frequency of 60 Hz (the period is approximately 16.3 milliseconds). The various vertical frequencies address a sync PROM (M2) whose output data is latched by latch N2. The outputs of this latch are the various polarities and phases of the vertical timing frequency used to synchronize the TV monitor display. These signals all run at a frequency of 60 Hz. See Figure 3-10, Vertical Sync Timing Diagram for the relative timing of these waveforms.

The end result of the horizontal and vertical timing waveforms is to synchronize the TV monitor display (COMP SYNC*). This display consists of 262 horizontal lines per frame, with each line being the time equivalent of 768 12 MHz clock pulses. Each frame is repeated 60 times per second, providing the necessary frequency of display refresh that provides a stable non-flickering display.

Super Breakout 3-9

Page 46

uno voeo eimcurn PLAYFIELD ROM

Figure 3-10 Playfield Generator Block Diagram

E. PLAYFIELD GENERATOR (See Figure 3-3, Sheet 4 of 5) The playfield generator generates both the alphanumeric and playfield data for the TV monitor display. The video is actually generated by graphics ROMs P4 and R4 and 8-bit shift register R3. See Figure 3-10.

Which alphanumeric or playfield characters are to be displayed and where on the screen they are to be placed is controlled by the MPU Display RAM (F4, H4, J4, K4, F3, H3, J3, K3). To understand how MPUgenerated data in the display RAM controls placement of these characters, it is first necessary to understand the organization of the playfield display itself. The playfield is structured as a 32 x 32 matrix, consisting of 32 horizontal rows of characters—each row being 32 characters wide. (Actually, only 28 of the 32 rows of characters are visible on the screen, since

3-10 Super Breakout the bottom four rows are blanked out by the V BLANK* signal during the vertical blanking and retrace period.) Each character is structured as an 8 x 8 block, eight lines high with eight bits of data per line. See Figure 3-11.

Since there are 32 rows of characters, with 32 characters per row, there are a total of 1 024 (32 x 32) positions in which to place a character. The display RAM consists of the eight ICs mentioned above. Each of these chips is a memory size of 1,024 addresses, with one bit of data per address. When all eight of these RAMs are considered as a group,they have a memory size of 1,024 x 8.

Because of the unique way in which the game circuitry is structured, each of 1,024 addresses in the display RAM corresponds to one of the 1,024 possible

Page 47

32 ———_

(8BIT x 8BIT CHARACTER BLOCKS)

gq (SBIT x sBIT CHARACTER BLOCKS)

GOIN 1 PLAYER

OH 1H 2H 3H 4H 5H 6H 7H met ty | | |

vl i |

BBIT x 8BIT

CHARACTER BLOCK OH 1H 2H 3H 4H 5H 6H 7H 8H ov

wT OL wt LJ Ll wl L____ wh LL

wl L___

THE OUTPUT OF SHIFT REGISTER R3

Figure 3-11 Character Display Data

positions in which a character can be placed on the playfield. In other words, for each position on the TV monitor screen in which an 8 x 8 playfield character can be displayed, there is an 8-bit data code stored at a particular address in RAM, which determines what character, if any, is to be displayed in that position. The method by which the MPU writes the appropriate playfield data to each RAM location, and then the horizontal and vertical timing signals read this data out for actual video generation is known as “cycle-sharing.’”” The circuitry that controls this cycle-sharing technique is composed of the three

Super Breakout 3-11

Page 48

ZA = ADDR3

2B = ADDR2

ZC = ADDR1

ZD = ADDRO SWITCH EQUIVALENT OF DEVICE 9322 (I.E., H2)

2B = 32H

2C = 16H ADDR 1

8H ‘ZD = 8H ADDRO

Figure 3-12 Address Multiplexers Equivalent Diagram

2-to-1 multiplexers, K2, J2, and H2, which select one of two sets of addressing information to address the display RAM. This circuitry functions as follows:

1, When MPU ®2 clock is high, the MPU address bus (A0-A9) addresses various RAM locations, and writes appropriate playfield picture codes into them, via the MPU data bus (D0-D7).

  • When ®2is low, horizontal sync signals (8H-128H) and vertical sync signals (8V-128V) are now allowed to address this game display RAM and read data out of it. This data being read is latched by latches P2 and M2, and labeled DISPLAY 0-DISP- LAY 7 (See Figure 3-12).

Since the data was read out of the RAM by the horizontal and vertical sync signals, the picture codes contained by DISPLAY 0-7 always correspond to the

3-12 Super Breakout portion of the monitor display currently being scanned. Because of this, the DISPLAY 0-7 outputs can be used to generate video information for immediate display. These DISPLAY signals address one of 64 8 x 8 pictures stored in graphics ROMs P4 and R4. The output of the ROMs P4 and R¢4 is then converted to serial video information by shift register R3.

The PLAYFIELD signal represents all of the playfield and alphanumeric character video information. It is summed into the video summing circuit, as shown on sheet 4 of the schematic diagram.

EF. MOTION OBJECT GENERATOR (See Figure 3-3, Sheet 4 of 5) The motion object generator produces the video for Super Breakout’s three moving objects (3 balls).

Page 49

The actual video information for these objects is stored in ROMK6. This ROM provides a total memory size of 32 x 8 bits. (see Figure 3-13).

The MPU controls the positions and different configurations of this video by information that it stores at selected addresses in the display RAM. Each of the three motion objects corresponds to three bytes of data stored in this RAM: one byte determines which of the pictures in ROM is to be addressed; the second byte determines the vertical position of that motion object; and the third byte determines the horizontal position of the object.

These bytes of RAM data are accessed by horizontal sync signals 8H, 16H, 32H and 64H at the beginning of each horizontal scan line (during the horizontal blanking period, i.e., when 256H is low). Therefore, before each horizontal line is scanned, the motion generator receives the necessary information to tell it what, if any, motion objects are to be displayed on that line.

Vertical position data (DISPLAY 0-DISPLAY 7) is received by vertical line comparators C4 and L4. These comparators determine if a motion object is to be displayed on the line currently being scanned. Take, for example, the data code for an object to be displayed beginning on line 120. The RAM byte data code of 01111000 would be loaded into the comparators. If the vertical line count (as determined by 1V, 2V, 4V, 8V, 16V, 32V, 64V and 128V) is also at 01111000, a compare signal (pin 7 of L5, low) will be generated. This signal initiates one of the three vertical load pulses at K8, LDV1A, LDV2A, and LDV3A. These vertical load pulses are used to load the ROM’s video information into appropriate video shift registers.

In review, for each ball, the motion object generator receives one byte of RAM data (DISPLAY 0-7 going to C4 and 4) that controls where that object is to be displayed vertically. The generator receives a second byte of RAM data (DISPLAY 7 going to ROM K6) that selects the ball picture to be displayed. The correct video information for that picture (VID 5~7) is then loaded into the appropriate shift register (N7 for ball 1, L7 for ball 2, and J7 for ball 3).

A third byte of RAM data is necessary to determine where the object picture is to be placed hori- Zontally. This data (DISPLAY 0-7) is loaded into a pair of horizontal counters (R5 and R6 for ball 1, P5 and P6 for ball 2, and N5 and N6 for ball 3). These counter pairs are preset when the horizontal scan of that line begins (256H* goes high). The counters begin counting up at the rate of 6 MHz. When the counter pair reaches a specific point in its count sequence, it gen-

MOTION OBJECT GENERATOR

pereaY. HORIZONTAL LOCATION COUNTERS

DISPLAY 0-7 FROM VERTICAL DISPLAY LOCATION RAM COUNTERS

MOTION OBJECT PICTURE ROM SHIFT OUT PICTURE DATA

PICTURE DATA VIDS-VID7 |MOTION OBJECTS} VIDEO ISHIFT REGISTERS, VIDEO (BALL 1, 2, & 3) MOTION OBJECTS |

Figure 3-13 Motion Generator Circuit, Simplified Diagram

Super Breakout 3-13

Page 50

erates an enable signal that allows the shift register serial data previously loaded into it from the motion object video ROMs to be shifted out. The serial video information for each of the motion objects is then summed into the video summing circuit (as shown on sheet 4 of the schematic diagram).

G. SWITCH INPUT CIRCUITRY (See Figure 3-3, Sheet 1 of 5) All off-board control switch inputs as well as onboard DIP switch inputs are received and decoded by data selector M8. All switch inputs are multiplexed down to two input lines (pins 7 and 9 of M8) via H9, j9, and MPU address lines ADRO—ADR2. These two lines (pin 7 and 9 of M8 are then gated onto the MPU data bus (D6-D7) by the MPU address decode SWITCH. When the MPU wants to look at any switch, it merely addresses that switch and reads back its status on either D6 or D7, See MPU memory map address output and corresponding data input line for any of the game’s switches.

H. PADDLE CONTROL (See Figure 3-3, Sheet 2 of 5) The paddle control is a linear clutched potentiometer (POT) with one side of the resistive element to ground, and the other side to +5 volts. The wiper of the pot is then connected to the inverting input of comparator device L10, pin 10.

A ramp generator comprised of transistors Q1, Q2, and Q6 and capacitor C53 produces a positivegoing ramp with a slope determined by capacitor C53. This ramp is inhibited at each VBLANK pulse which occurs on each picture frame. VBLANK turns Q1 “on”, which created a direct short across C53, discharging the voltage across it as illustrated in Figure 3-14. When VBLANK goes low Q1 turns “off”, removing the short from across C53 and allowing it to begin charging up through Q2.

Voltage follower Q6 buffers the positive ramp to the non-inverting input of comparator L10, pin 9. As the player rotates the paddle knob, the wiper voltage will at times match or cross the ramp voltage and the output of L10, pin 7, will go high. This occurs each and every time these two voltages cross.

This high comparator output is gated to the SENSE 1 line when the MASK 1 signal is low and enables the M10, pin 8, gate. MASK 2 is always low, inhibiting gate M10, pin 11, because there is only one paddle available to the player for the Super Breakout

SENSE 1 DC VOLTAGE FROM +12V WIPER OF POT (L10, PIN 10)

VOLTAGE RAMP

(L10 PIN 9)

VBLANK

Q1 OFF ee

Q1 ON (SHORT ACROSS CAPACITOR) This time difference indicates to the MPU program what the vertical location of the paddle should be.

| APPROXIMATE COMPARATOR

i LIMITS WIPER

VOLTAGE

A PICTURE FRAME

Figure 3-14 Significant Paddle Signals and Timing

3-14 Super Breakout

Page 51

game. Therefore SENSE 2 is always high which enables the logic path for the SENSE 1 signal to M10, pin 6 (NMI). The NMI signal when low flags the microprocessor as to the location of the paddle on the TV screen at any given time.

J. VIDEO OUTPUT (See Figure 3-3, Sheet 4 of 5) The video output circuit receives all the video signals (PLAYFIELD,BALL 1, BALL 2, BALL 3) and gates these signals together at NAND gate L6. The composite sync (COMP SYNC") signal is then summed together with the output of L6 via resistors R52 and R27 to the base of voltage follower device Q5 (2N3643). The signal on the emitter of this transistor then becomes the composite video signal sent to the game’s display monitor.

K. AUDIO OUTPUT (See Figure 3-3, Sheet 5 of 5) The audio output of the audio generator is applied to one leg of a 5K ohm potentiometer (located behind the coin door next to the self-test switch as illustrated in Figure 1-6 of Section 1 of this manual). Varying the wiper position of the potentiometer varies the signal input to Audio Amplifier device D9. The output of the audio amplifier is then connected to an 8-ohm speaker located in the attraction panel over the TV monitor screen.

Super Breakout 3-15

Page 52

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 53

we rus tt

(Rie)a7LL
dro=|slelsleds= _|s le |e leds
ats“BEeERwets leo?
oftsmeweeeeRy
"38oe 8,elwehs

Hee gfe} S36

ereoga ve
[sont feFreeeieee F

l ; bee

(Me)ED:(Re)ete)
Ee2ge322%

2883 £388 weer Feeley =F Tek ds

SeeTeesh,wes.
ceejeerYBLANEXae)le>28VBLANKE
eSa4 caeveer
BeePeav—2hes[lo i2lan2h
yiioy —4he9ualte— vacane
=)Pedaythe §ee
evSai 0 ggt2 lanaof'S—— syne
ty—Slaczat

eu ese a?

RRBBi7

an P(e) + nsyne R50 Lad Ras

R13,6,8,109,3] Por S¥

es fh +— (PULLUP) proved . neces LOL2 rev C1-B, 10-13,17-23,25,26,28,

3poretara
T°Lésvencsy2922.28 96

a

ceisepewsas

le. SVAC|C J 3 4+ ceq moot ao ase ere, tw? wesc Bl INaoo! mal

vesver ES roy Gite. NOTICE 70 al PERSONS RECENNG THs pRaMnIS OSSETIAN

ces7Si2written.

ae ‘This drawing is only conditior

2SVACP-+ipt nor possession tnereot eon ers of ans re
ae | Teeswleso [exebie ai ie
MopTSTSaC eea ae
om|TVOTLFT°LTReveal encepitounasutactore by vendors ol atu incor

cove [EES :

AirsSiam or wel‘permission from the corporatior

asver [YE oH

Figure 3-3 Super Breakout Schematic Diagram Sheet 1 of 5

Super Breakout 3-17

Page 54

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 55

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atan, Inc. Sunnyvale, California. This drawing is only conditionally issued, and ‘either receipt nor possession thereo! confers or tanaters, {any right in, oF license {0 use, the subject matter of the Srawing oF any design or technical information snown thereon, nor any right to reproduce this drawing or any part thereof, except for manutacture by vendors of Atari. tncor porated and for manufacture under the corporation's wt {en license, no right to reproduce this drawing is granted

fortheSubjectmatter thereof uniess by writes agreement

‘with or weitten' permission trom the corporation.

OM 2

ABS“StasvoltZinsope
aewfaN2pPROMS
:a23p2_sRowa
aulBla 5 Beab2_saaeePROTSED
al3see,|| PROMS“?meine
azBas $ eslspe
al.Beereebt—Fromes
as4aOy53011p— FEMSSET— 2508 — syncs

abe Oa

—_Mdsp2

wean

oppcmewatae
aRiw2speaneTee terkeae§] SERVED
—-+32Swiren = Ave? —1S]9884 gfe
iaraA
ls3aycame
_—islaa4TIREave——as=LAMe2,
5AdesBaiESMASE
btwADRLStaraaMASKED
Jssor 5veg—HfowarfCOUNTER
  • A 2 1s

. PRe® ware — +sv

sav asi av av ie mao

_Hia pees — cesses
=——29cae

te Tae sey —_ Rat Las «

ieRyeate

—— Zp SENSE?

VBLANK

sttce1 2-40 a 4g Mw

=centers{¢p*$—_

Mic! CESSOR

Figure 3-3 Super Breakout Schematic Diagram Sheet 2 of 5

Super Breakout 3-19

Page 56

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 57

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbidden without the fio ween permission ol Atari. Inc." Sunnyvale, nia" This dfawing #8 only condrtionally issyed. and iptrot possession thereat conlers or irenalers ‘or heense 10 use, the subject matter of the any right Grawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereo! except for manutacture by vendors of Alar incor orates and for manufacture under the corporation's writ. {enicense, no aght to teoroduce ts drawing 's granted sal is brine subject matter there uniess by written agreement 2 bat — pispeave ttt or writen permission Irom the corporation 3H. 19} DisPUAYS

hsp1sisecave

24 25 D DusPLay2,

Sep2oispay

Sep 2c} — vispiaras ec § > or

FR)

4 uss 3 {50 SF sal’? — pispuav7

1574oeh's

ar DISPLANS, ce ct a

be+Pee

os

sreeeles|_4,
Can:4,2»,/.
r“\
fisoatc)2B3
vyC>3“Syasvseysv
(6fewo] sur'
taeJhebie1sls
asfrsonens
> >o&+apeeas
aace?a7
——apsotADRese
osaces—2AS
ieaves—3ws
asoles25,aves —4laa
=o—_—_+=2db)aDR2—ae
Hs2)posApa—&1
uySoe4zay[vpDRGae
04 KOPL7os—!loaoaWoy
oatve2os032be
DImio213ps

! 4

oli}{454.
————veaKefi | seoaCe
+s¥+sy+BYNot usco| o33a48|NoT useD] 033442
9loam mile mle mln

1o JepTo

(eop—2aeP
no8ALial
weg—&asFeO
aves—4asPEO a
apg7—[AT\-o8y
Ape—"AeVERSION
aves——S
aves—Ae

Ses as

avez——4Jaz
apet——31
apes—4Ao
1—4br

wa De

5)EeMEMORY

4 D4

ps—DS

pe pe

>4bs

va}

btertay

ossts |ossass |ossess ccr_oez |cxs _ogz loei_o82. a0 ie

Roms Rome fom?

ee_Figure 3-3Super Breakout Schematic Diagram

Sheet 3 of 5

Super Breakout 3-21

Page 58

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 59

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction forbidden without the ‘Sunayvale, 's drawing is only conditionally issued, and "not possession tnereo! conters or ranaters ‘oF license to use, the subject matter of the ‘rawing or ‘any design or technical information shown 10, Nor any right to reproduce this drawing OF any part th ‘hereof. except for manuiaclure by vendors of Atari, (ncor" land for manufacture under tne corporation's wrt 10 reproduce this drawing 's granted forthe subject matter thereat unless by writen agreement ‘with or watten permission trom the corporation,

esezac

Bree % ES 53 35 peas B36 Bio a6 ( 4 |S 1649 Ed

ee)[ASTOCAbeou
)aleeasae ee

r s

258—TGETusiescof"SIETUsiea cot
cmjo_GaBALL

wer BA BY GCA oA

petsTeyOrpape fe ivor

PR) ABODE Cay aon eugse Siz gees

ager3333ag
So 24la54Saoe
225 3186320ges
alas ledsAASelsfele blot.+
@)ABC Beaecr.eAST DEF GaN |o

Per a

esPeFeu7

vol sf is s|

reT Lsieacol3 Lsi@s copaIsses4
ZhenheetekeaBACCE,
BA BB BADCA OBO ADC4sitsr
Perverpana“Pe
P (Re)HAPUdV2Za ———=

(Re) vege geys 2ELe 222%

2533102338nay
939915SSSaaa
pBdo046))BdAD* ee
daleleletsla [5 edohelabals fe fe fo
R)eee oeaR eee’Awe oSoH
pereroH]
moeSaisaleeNeooh‘s2
er wsicaco!Ber shee colfin2
{aleeKteleea
BA ABA aD Ssit3

Taree peer Ye

PRE)KUMNPLesCDVBA=

Pe

+ev sv PUN IECB BACT BACLT oe come

vines OH Ste

MOTION ,PLAYFIELD . VIDEO

Figure 3-3 Super Breakout Schematic Diagram Sheet 4 of 5

Super Breakout 3-23

Page 60

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 61

2 °

DISPLAYSho=F

ay 158 Audio

pyspuayy ——2s0 -

caay—*128/
DISPLAYsoz=
7wvHe
pisPLay3——420Be

!

ey—Bee<se

i TUES -

Aupideecal
caole*

vous 3 D9 ia] AUDIO

=4roaiooaiBsoo

ea 43 une

RaoLcarPF EPecat2]

‘i 4 i = 001 208 oe ca pie 2eopt “

=ote=

P (Re) P (ae)

(ee),[P:4.
Pele Faleale Pal?eju,
7434a
ran—Fee"feNeeaeae

< S

vya1s
—oraL
Csee)Byer

Laney

LAMP2, NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction’ forbidéen without the Specific weit permission of Atari, Inc,” Sunnyval California’ Thie drawing 1s only conditionally issued, and pelther vaceipt nor possession thereo! confers or transfers {ny right In, oF Hcense to use, the subject matter of the drawing 2” any design or technical information shown thereon, nor any right 10 reproduce this drawing or any part {hereo! except for manutacture by vendors of Atari, Incor porated and for manutacture under the corporation's writ. fen license, no right to reproduce thls drawing is granted fr the subject malter thereof uniess by written agreement ‘with oF written permission trom the corporation,

igure 3-3 Super Breakout Schematic Diagram Sheet 5 of 5

Super Breakout 3-25

Page 62

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 63

on BK VT ‘our jot et te

3) Ww—nl
FOR+aTeBKi4
PowerOY] oF:oN2
‘SUPPLY2Re
SCHEMATIC.io|ENcvosure VON?w31 oy
Seeywip |eeeBu.+3| 9[ 9)

007197-0 2

7-01lwfang<wom

Zz] x tote

eK teyaL 33yap)
oTRcS,TRE -qyl4]Ser ofSweTay

i 7 10 2 oS 08 ott po LN

ot BKKorot maha aie aares anes oteae
5] Wwtp‘yw
:ftHee fe ePaper§w5

TR or

INTERLOCK INTERLOCKMONITOR|7

| SPEAKER MS iv

(a L

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING GONFIOENTIAL” Reproduction igroidcen. without the

Fem pootsale canaraconan

I except for manufacture by vendors of Alar, meOr and for manufacture under the corporation's writ {en license, no right to reproduce this drawing is granted for the subject maiter thereat uniess by written agreement fen permission from the corporation

Figure 3-15 Super Breakout Harness Schematic Diagram 00325501 D

Super Breakout 3-27

Page 64

hac) HOLIMS WVIS

a ow Aten pas Zz af

w -——oz i D BD x |o . c n n oR ro

  • c m # 4d AN

L

COIN #2 CLEFT)

FRONT VIEW OF COIN DOOR

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING 15 POS MOLEX GENRGGENT/AL ‘Reproduction iginsten out the aly issued, and PLUG + MALE tne roca oane sin or eanae foe, Ie abtant mater of fe TERMINALS

corporation's wnt crane gated Ortho subject matter ereor unless by writer with or watten permiasian from the corporation,

Figure 3-16 Coin Door Schematic Diagram 03040101 B

3-28 Super Breakout

Page 65

Uses rem Sonne gems

=,SRG
Sb029ge
gacude46
4ac39

a 1 1 *

WypoWwDdtutstwin
7\olZzZ
aeHe"fae|

] w. ~E Nn ov

we |le,“£
RZ2BK/Rggwok
SyiaLaa:7
ic]ase|}0|=©|v
ark|yuvieey
|“<

O <

Wikba|;aaa
z1g>|§g
1le1S| Reae })ae
7onRl]
cp|ea
ZzIRIeBis
|oewpe ewis=

q 3 qe! let = |p

RoBle:

18 ,

LiegeJoo4
Ra|Bis*

¢G |x [

NOTICE TO ALL PERSONS RECEIVING THis DRAWING CONFIDENTIAL’ Reproduction. forbidden without the Specific written permission of Alar, ine,” Sunnyvale, Galiforia Ts drawing 's On conditional issued, and ‘nor possession thereat confers or ransters to use, the subject matter of the

Srawing or any oeinniealinformation. shown

thereon, nor any right to reproduce this grawing or any part theres! except for manulacture by verdors of Ata, Incor orated and for manulacture under the corporation's writ {en license, no right to repreduce this drawing is granted forthe subject matter thereof uniess by written agreement ‘with or watten permission Icom the corporation. a

L LStL-2h WAWOASNVYL

jO-SSS700V Gd

Figure 3-17 Type B Power Supply Schematic Diagram 00719701 c

Super Breakout 3-29

Page 66

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 67
NOTE

If reading through this manual does not lead to solving a specific maintenance problem, you can call Tele-Help™ at the following two Atari Customer Service offices.

Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 I Of Telex 17-1103 (Monday - Friday, 7:30 - 4:00 pm Pacific Time)

From California, Alaska, or Hawaii, dial (408) 745-2900

From anywhere else in this area, dial toll-free (600) 538-1611 my

EAST U.S.A.

Atari Inc. New Jersey Customer Service Office 46 Colonial Drive, Piscataway, NJ 08854 Telex 37-9347 (Monday - Friday, 8:30 - 5:00 pm Eastern time)

From New Jersey dial (201) 981-0490

From anywhere else in this area, dial toll-free (800) 631-5374

Super Breakout

Page 68

A. CLEANING The exteriors of game cabinets and Plexiglas® panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe the acrylic plastic panels, because any dust can scratch the surface and result in fogging the plastic.

B. COIN MECHANISM Components On Coin Door Figure 4-1 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted. Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechanisms. Powering the game causes the lock-out wires to retract far enough to allow genuine coins to reach the coin box. When AC power to the game has already been turned off, the lockout coil is de-energized, causing the lock-out wires to move out far enough to divert coins to the return chute.

Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire exten-

LOCK-OUT COIL LAMP HOLDER ding out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.

Also shown in the photograph is a slam switch assembly. It has been included to defeat any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.

Access to Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 4-2. Or, if necessary, each coin mechanism can be entirely removed from the door merely by pushing down on a release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 4-3.

Plexiglas® is a registered trademark of Rohm & Haas Company.

Figure 4-1 Coin Door Assembly

42 Super Breakout Figure 4-2 Hinging Open the Magnet Gate Assembly

Page 69

Figure 4-3 Removal of Coin Mechanism

Cleaning of Coin Paths

CAUTION The use of an abrasive (such as steel wool or a wire brush) or a lubrication on a coin mechanism will result in a rapid buildup of residue.

By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling water and a mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out al! water with compressed air.

Figure 4-4 shows the surfaces to clean inside the coin mechanism. These include the inside surface of the

(CLEAN BOTH SURFACES WHERE COIN ENTERS THE MECHANISM, AS WELL AS THE MAGNET)

Figure 4-4 Surfaces to Clean Inside the Coin Mechanism mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these you can guide the point of a screwdriver or similar tool along the edge of the magnet.

If coins are not traveling as far as the coin mechanisms, you will need to clean the channel beneath the coin slot. To gain access to this channel, use a 3/8-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 4-5). Removing the plate will provide access to the entire channel

Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.

Figure 4-5 Removal of Plate Covering Rear of Coin Slot

Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 4-6 shows this lubrication point.

Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest Position of its trip wire should be as shown in Figure 4-7. Use extreme care when handling or touching these wires.

Super Breakout 4-3

Page 70

MANUALLY HOLD DOWN REJECTION BUTTON AND APPLY ONE DROP HERE

LOCK: OUT WIRE

Figure 4-6 Close-Up View of Lubrication Point

In Figure 4-7 you will note that the coin switch trip wire is oriented into the “V” of the secondary coin chute. The wire should extend to only about 1/8” beyond the chute.

A retaining clip holds the wire onto the switch actuating stud. !f you should loose a retaining clip, all is not lost. Just crimp the switch actuating stud over the trip wire with a pair of pliers.

Mechanical Adjustments on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjustments, remove the coin mechanism from the coin door. Then take it to a clean well-lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need a set of several coins, including both new and old, worn ones. Figure 4-8 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be done by someone who has experienced in servicing coin mechanisms and who understands their operation.

4-4 Super Breakout CORRECTLY ADJUSTED TRIP WIRE

Figure 4-7 Detail View of Coin Switch and Trip Wire

General Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properiy adjusted. If troubles still persist, check the conditions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism

Page 71

ITEM IDENTIFICATIONS Kicker and Separator Screws Washers Kicker Si ator Gate Lever Spring Gate Pivot Pin Mainplate Assembly “ washer Rail Gate Assembly Cradle Assembly

  • Upper Gate Pivot Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magnet Gate Adjuster 17 Retaining Screws 18 Coverplate Assembly 19 Return Coverplate 20 Coverplate 21 Mounting Studs 22 Lower Gate Pivot Spring Kicker and separator 23 Coin Release Lever

. Set the acceptor with the back of the unit facing you in the test position. . Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws. |. Insert several test coins (both old and new) and note that some are returned by striking the separator. . Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw. . Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted. . Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw. . Insert the test coins and note that some are returned. . Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw. . Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted. |. Be sure that both screws are tight after the adjustments have been made.

Magnet gate . Set the acceptor with the front of the unit facing you in the test position. . Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through. . With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate. . Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted. . Fix the magnet gate adjusting screw in this position with a drop of glue.

Additional Cleaning Remove the transfer cradle (12) and the undersize lever (14). Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins. Replace the transfer cradle and the undersize lever. To be certain the coin mechanism is completely free of any residue, place the mechanism in boiling water for several minutes. Carefully remove it and let it air-dry completely before reinstalling in the door.

Figure 4-8 Adjustments on Coin Mechanism Super Breakout 4-5

Page 72

C. TV MONITOR ADJUSTMENTS

CAUTION For best results be sure the game has been turned on for a while before making any TV monitor adjustments.
NOTE The TV monitor adjustments are accessible through the rear door panel of the game cabinet. These adjustments have to be done whilethe game is energized. Therefore, only persons familiar with safety measures and repair procedures on electrical equipment should perform them.

The TV monitor should be adjusted only when the picture is distorted or if the contrast or brig htness seem out of adjustment.

The monitor's adjustments function like those of a conventional, home television set, except that the volume adjustment has no effect. Instead, the game produces its sound in circuits separate from the TV monitor. Figure 4-9 shows the location of the adjustments on both TV monitors used by Atari. Your game contains a TV monitor manufactured to Atari specifications by either Motorola or TEC Video electronics. When making adjustments, follow these general guidelines:

BRITE (Brightness)—Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up.

CONT (Contrast)—Adjust so that the images are as bright as possible against the dark background without being blurred.

HORIZ HOLD (Horizontal Hold) or HORIZ OSC (Horizontal Oscillator)—Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken upinto a series of diagonal lines. Adjust for a stable, centered picture.

VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture.

D. FUSE REPLACEMENT Super Breakout contains seven fuses, five on the power supply assembly in the lower part of the cabinet and two on the TV monitor assembly. Power supply fuses are accessible through the lower rear door assembly. TV fuses are accessible through the

conraast |" VT Coan Cie on arian \\_ Melon VERT HOLD HoRIZ. HOLO- VOLTAGE SWITCH (leave in right position)

TEC MODEL TM- 600/623 ‘CONTRAST —> Honiz. osc. > 2 FUSES~ REMOVE. BRIGHTNESS COVER To RED. A cE (both 0.8.8 quick Blow) FOCUS

MOTOROLA MODEL M5000/M7000

Figure 4-9 Locations of Adjustments on TV Chassis

Super Breakout

Page 73

TV MONITOR REMOVAL

1. OPNAAPOND

Unfasten two smooth pan-head bolts from the

control panel by holding down the bolt heads

with one hand and using the other hand to

remove the wing nuts. These wing nuts are

located on the inside of the cabinet, and can

be reached through the coin door. Unpiug contro! panel Molex connectors. . Remove control panel. . Slide out playfield Plexiglas shield. Remove cardboard bezel. Remove wood TV monitor retainer board. . Unplug TV monitor chassis connector. . Slide out TV monitor shelf through rear access door.

Figure 4-10 TV Monitor Removal Super Breakout 4-7

Page 74

LAMP/SPEAKER ASSEMBLY REMOVAL

  • Remove three button-head screws.
  • Remove Plexiglas retainer.
  • Remove Plexiglas shield.
  • Slide out lamp/speaker assembly.

FLUORESCENT LAMP REMOVAL

  • Remove retainer clips which hold built in socket.
  • Gently rotate fluorescent bulb until it slips out of socket. Remove fluorescent bulb.

Figure 4-11 Lamp/Speaker and Fluorescent Lamp Removal

upper service panel door. Replace fuses only with the same type as follows:

TEC TM-600/623 Monitors: 3AG 2-amp and 0.5-amp quick-blow, 250 volts Motorola M5000/M7000 Monitors: 3AG 0.8-amp quick blow, 250 volts Power Supply: Fuses F1 and F2—3AG 3-amp slow-blow, 250 volts Fuses F3 and F4—3AG 2.5-amp slow-blow, 125 volts Fuse F5—3AG 8-amp fast-blow, 125 volts

4-8 Super Breakout E. TV MONITOR REMOVAL (See Figure 4-10) If the TV monitor proves to be at fault, remove the monitor as shown in Figure 4-10.

F, LAMP/SPEAKER REMOVAL (See Figure 4-11) Super Breakout contains a combined fluorescent lamp and speaker assembly, located at the inside top of the game cabinet assembly. To replace this assembly or any subcomponent, remove the Plexiglas retainer and shield as shown in Figure 4-11. ASSEMBLY

Page 75

NORMALLY CLOSED (N.C.) CONTACTS

SWITCH

TURN COUNTERCLOCKWISE TO REMOVE

LIGHT-EMITTING DIODE (L.E.D.) CONTACTS

NORMALLY OPEN (N.O.) CONTACTS DOUBLEPOLE SINGLE-THROW (DPST) SWITCH WITH INTERNAL LED

Remove all wires from the suspected switch. Turn the switch counterclockwise while holding the cone-shaped nut on the outside of the game cabinet. Install a new switch using the reverse procedure. Reconnect the harness wires.

Figure 4-12 LED (LICON) Serve Switch Removal

G. LED (LICON) SERVE SWITCH REMOVAL (See Figure 4-12) The LED serve switch on the front panel has a very low failure rate. In case this switch should ever be suspect, first test it. To test the switch perform the following steps:

  • Unlock and open the coin door.
  • Remove the wires from the suspected switch.
  • Set Multimeter to ohms scale. . Set ohms scale to R x 1, then zero the meter.

. Connect multimeter leads to appropriate LED switch contacts. (See Figure 4-12 for designation of switch contacts.)

. Check contacts (push switch button in and out) for closed and open continuity.

. If the contacts do not operate sharply or always remain closed or open, then replace the LED swich as outlined in Figure 4-12.

Super Breakout 4-9

Page 76

SQUEEZE TABS, THEN PUSH THROUGH

Figure 4-13 Lamp Start Switch Removal

H. LAMP START SWITCH (See Figure 4-13) The one-player and two-player start pushbutton switches on the control panel are each backlighted by

4-10 Super Breakout two #47 lamps. The swiches themselves are cherry switches with gold-plated contacts. To replace either start switch, see the procedure outlined in Figure 4-13.

Page 77

PADDLE CONTROL POTENTIOMETER

ALLEN-HEAD SET SCREW

Figure 4-14 Paddle Control Removal

J. PADDLE KNOB (POTENTIOMETER) REMOVAL (See Figure 4-14) The paddle knob on the control panel is a potentiometer made with resistive carbon material. After frequent use, the carbon material begins rubbing off the potentiometer. This results in a fine dust that can cause the potentiometer to not perform smoothly or linearly. This problem can be detected by performing the potentiometer test, as described in the game’s self-test procedure. (See Chapter 1 for details on the self-test procedure.)

If it does become necessary to replace this control, follow the procedure outlined in Figure 4-14. GAME SELECT (ROTARY) SWITCH

SEALED (CLEANING NOT POSSIBLE)

CONTROL PANEL

ALLEN- HEAD SET SCREW

Figure 4-15 Game Select Switch Removal

Kk. GAME SELECT SWITCH REMOVAL (See Figure 4-15) If you need to replace this three-position rotary switch, follow the procedure shown in Figure 4-15.

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for the Super Breakout game.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this catalog, and the serial number of your Super Breakout game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Super Breakout 4-11

Page 78

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 79

ILLUSTRATED PARTS CATALOG

The purpose of this chapter is to provide you with the necessary information for ordering replacement parts for the Super Breakout game.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this catalog, and the serial number of your Super Breakout game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Super Breakout

Page 80
  • 2 sera

#9) 33)

28).4 ZERO G)

@9) 2 RRO AT aD it ed

  • 2 ZERO © !

S (3 ee 65)

© Becca (28) 4t ; (5)

  • amp eects AN

5-2 Super Breakout

Page 81

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproguction. forbidden without U Specific written permission of Alar, nc. Sunnyva Caitfornia, This drawing 1s only condilicnally issued, pliner receigt nor possession thereot con! Bay right in, oF Hcense to use, the subject Grawing of ‘any design or technical information shown tmeteon, nor any faht to reproduce iis drawing o any part thereat, except for manufacture by vendors of Atari, mcorporated and for manulacture under the corporalicn’s wit. fen ticerse, no right to reproduce this drawing is gran ‘or the subject mater thereo! unless by written agreement with or woiiten permission trom the corporaticn.

-_—_/

section [SelB

Figure 5-1 Final Cabinet Assembly A033260-01 D

Super Breakout 5-3

Page 82

Item Part Number Qty. Description 40 72-6808 1 Screw, Sht. Met., Pan Hd. Phil., #8 x 4" La | fost | 1 | te naps Screw town & | arte 2 | Hp-setein snateccer 43 82-8016 6 Screw, Button Hd., Soc. Cap, #10-32 x 1.0" Lg, B1k i i i ‘75-5120B 5 Bolt, Carriage, #10-24 x lk" Lg, Blk @ Figure 5-1 Final Cabinet Assembly ss | races & | Serco, mach. Pan tia, Phily #4-40 x 3/2" ta ATARI Parts List S| Gauescrer || Sraccer Goneroy mance

| Gusesl | P| Biretee ever sa | Gacieze Dee ee eleua., #8 x 2.50 t0. | S55G0-08 | now | ts'an'accepcabie suctivute For A03360-09 (ten 6) Item. Part Number Qty. Description 1 | 1009083-01 | 1 [Asseny, Coin poor bo] Roonsico | 2 [PEE Fee ebony. nype vee 3 | Rowena: | i ear ese a | Resor | Bert Shletd mrciosure 3 | Mossoeot | 1 | = Bovgeeera 6 *A023160-03 L " Game Board (Super Breakout) (PROM) > | “nosmaseces | 2 |" Sore guiten\s Harness 3] fossocn, 7 |S keer oe o | Aoseso: | 1 | Sabinet tvorapnics to | Romar | i |" Fleurs clane’Spester | fossa Tt | tRoniese 12 A033456-01 L & Control Panel Bi] tosszeeno: | t | tReet pcan tnd usca 1 | “sosoeicor | 2 | neatner, Pietisies 1 | covsos-03— | i | fecet vacuun Forana Xe | cosuascor— | 1 | Seats’ near oor 1 | Gosaizcor | t | Seat, "sptanee te | coer | 1 | seus Feinees roxy 1 | cocernar | | recnce, Coin’ sex 20 | gonuscor— | 2 | Savers Oot suleen 2 | taaose-or | >| Canes’ Shtpotas 22 033137-01 1 Shield, Monitor Plexiglas W/Graphics 23 033138-01 1 Attraction, Plexiglas W/Graphics 24 033265-01 1 Overlay, Monitor W/Graphics 2] gene i | Sone teoe’cnare ze | Seite i | feck ramal ize 39 | Secdoeso0e | 2 | Pisost Stow sions 3 me 28 72-6610 20 | Screw, Sht. Met., Pan Hd., Phil. #6 x 5/8" Lg. zs | raeezo | 4. | scree, she. aes, pan ages pritss a6 24" oa. 30 ‘72-6812 12 | Screw, Sht. Met., Pan Hd., Phil. #8 x 3/4" Lg 3] Gris | 4° | top nivety 3/t6 3.00 sade eas Blk 32 75-0108 5 Washer, Flat, #10 33 | toe i | Rasher’ spilt-recx, #20 34 ‘75-0158 4 Washer, Flat # 3] Geesston | | Seteh‘stone Pentatas 36 ‘75-5516B 4 Bolt, Carriage, #4-20 x 1.0" Blk yy | Tea 3 | fine'nce, Horde 38 75-990505S a Nut, Lock, Shallow Pattern, #-20 39 75-99090006 6 Well Nut, Blind Hole Fastener, #10-32

Super Breakout Gis Caters ey

5-4

Page 83

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 84

7 orice 10 ALL PERSONS AECEIVING THIS DRAWING CONFIDENTIAL’ Reproduction to specific. waillen permission of A Gitornias This sawing 8 only conditionally issuer Seutner receipt nor possession thereo! conters or transfers fry “ight in, oF license To use, the subject matter of the ‘drawing or any design or technical information shown ‘hereon. nor any right lo reproduce this drawing or any part thereot, except for manulacture by vendors of Ataf tnco porated and for manulacture under ihe corporation's fen license. no right to reproduce this drawing is granted ‘or the subject matter thereot uniess by written agreement ‘with oF written Bermission from the corporation.

Figure 5-2 TV Shelf Assembly

5-6 A033262-01

Super Breakout D a.03-2%%)

Page 85

Figure 5-2 TV Shelf Assembly Parts List

ATARI’

ItemPart NumberQty.Description
1003694-012Bar, Tie
2006319-031Decal, Copyright (1978)
3009236-012Support, Monitor
4033134-011Board, Monitor Mount
574-3504S4Spacer, Tubular Non-Threaded #% x .25 Lg
675-0454Washer, Split-Lock #%
775-5532N4Bolt, Carriage, #%-20 x 2.00" Lg
875-915S8Nut, Hex #%-20
992-0331Monitor, 19", B & W

Super Breakout 5-7 + wares Communications Company

Page 86

) Bike

“Bak. (COM) WK. ‘ wv z/eo Bil (COM) RIN

= ~ hs = PADOLE S ® =

2 —” 5 STALT? a START | o

ew wily Y/W(N.O}) WOR WO.) 3 2

( DouBLe) w/e:

(cAMITY ) WIEN

(com) BK

SMITE TERMS, SUCLLO PONT UR, (275)

Figure 5-3 Control Panel Assembly A033436-01 D

5-8 Super Breakout Wwisy a

wieu aL

~ DETAIL, 43 ~ (SERVE)

OUCE TO At PERSONS RECEIVING THIS DRAWING

‘ignt fo reproduce ths grawing or ol excopttormanutacture by vendors of Ata fod and for manufacture under the corporation's wr fenitcanse, nc hgh to reproduce ins srawing fs grantes forthe subject matter tnereot Uniess by written agieement ‘wth of wibten permission from the corporation

Page 87

Figure 5-3 Control Panel Assembly Parts List

ATARI’

Part Number Description

1A033257-011Assembly, Harness
2A007357-061Assembly, Double Lite Start Switch (1 Player)
3A007357-071Assembly, =™=7(2 Player)
4033457-011Panel, Control W/Graphics
5001856-011Bezel, Alum.
619-90221Pot, 5K, Slip-Clutch, Short Shaft
762-0021Switch, Licon - Led
873-8191Knob, Black
973-8251Knob, Black With Skirt
1064-010103011Switch, Rotary (Stackpole)
i78-69004021Tape, Foam, Adhesive, Blk.

(w'] ‘Warner Communications Company

Super Breakout 5-9

Page 88
  • 6 PLCS

@ © 2 PLCS @) oN

  • 2 PLCS
  • 2 PLCS @1) 2 PLCS 2 PLCS @2)
  • 2 PLCS

(3) 4 PLCS GN)

NOTIGE 10 ALL PERSONS RECEIVING THIS DRAWING eeriten_ permission ot Atal ine. “Sunnyvse, Galifornia’ This orawing f only conditional Issued and ‘either receipt nor possession thereat confers or transiers any fight in, oF license to use, tne subject matter of the drawing or ‘any design or techni ‘ner ight tore

Figure 5-4 Coin Door Assembly

5-10 A009083-01 c

Super Breakout

Page 89

Figure 5-4 Coin Door Assembly Parts List

ATARI’

ItemPart NumberQty. LDescription
1A007637-011Front Bezel Assy.—Used only on -01 Coin Door Assy.

A007637-02 Ref. | Front Bezel Assy.—Used only on -02 Coin Door Assy. A007637-03 Ref. | Front Bezel Assy.—Used only on -03 Coin Door Assy. A007637-04 Ref. | Front Bezel Assy.—-Used only on -04 Coin Door Assy. A007637-05 Ref. | Front Bezel Assy.—Used only on -05 Coin Door Assy. A007637-06 Ref. | Front Bezel Assy.—Used only on -06 Coin Door Assy. A007637-07 Ref. | Front Bezel Assy.—Used only on -07 Coin Door Assy. See Figure 5-5

275-91654Nut, 6-32
3A030362-011Coin Lock-Out Assembly, See Figure 5-6
4A007640-012Coin Switch Assembly, See Figure 5-7
5A002465-011Coin Counter Assembly
6004320-011Coin Door Weldment
7004341-012Secondary Coin Chute
8004344-011Key Loop
9004340-012Spring Return
10004337-012Bracket, Wire Form
1004338-011Lock-Out, Wire Form, R.H.
12004336-014Lock-Out, Wire Form, L.H.
13004326-012Button, Scavenger
1475-0464Lock Washer, #6
15006904-012Spacer
16007359-011Lamp Socket
1770-11-471Lamp
1873-30082Retaining “C” Ring, Truarc #5103-25
1975-99140016Self-Threading Nut, Tinnerman #SR188006
2075-026S4Washer, #6
2175-0051613Kepnut, Style 842, Stl., 6-32
22008629-012 | Spring
2371-21184Lock Assembly, Hudson Lock
2471-1225CU2Coin Mechanism for American Quarter Only

71-125FB Ref. } Coin Mechanism for Belgian 5 Francs Only 71-1205FF Ref. | Coin Mechanism for German Mark Only 71-1201MG Ref. | Coin Mechanism for Swedish Krona Only 71-1201KS Ref. | Coin Mechanism for Japanese 100 Yen Only 71-1210PE Ref. | Coin Mechanism for English 10 Pence Only 71-1220CA Ref. | Coin Mechanism for Australian 20-Cent Piece Only

25007753-011Plate, Anti-Probe
26A007638-011Switch Assembly, Slam
27A006921-011Hamess Assembly

Super Breakout 5-11

Page 90

2 Pues

  • 27s

@® io) @ PLCS he rcs

B)e pus 4y)eruis

B)ercs

s)encs

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING

‘hereon, nor any right to reproduce this drawing or any part thereot, except for manufacture by vendors of Atari, ("cor porated and for manulacture under the corporation's writ: {en license, no right to reproduce this drawing is granted fr the subject matter inereo! unless by written agreement ‘with oF weltten permission from the corporation.

ure 5-5 Front Bezel Assembly A007637-01 thru -07 D

5-12 Super Breakout

Page 91

Figure 5-5 Front Bezel Assembly Parts List

[item [Part Number | Qty. Description

1004328-011 Bezel
2See below2 |Ring
3004331-012 Coin Shield
4004332-012Primary Coin Chute
5:004327-012Bearing, Scavenger Button
6004329-012Clamp, Price Plate
7See Below1 |Price Plate
873-30092 |Retaining "C" Ring, Truarc #5103-37
972-1604S4 Mach. Ser., 6-32 x k Lg. Pan Hd., Phil
lo75-0462 Washer, #6, Split-Lock
1175-99140016Self-Threading Nut, Tinnerman #SR188006

foasH Nol stem ETE 7 DEXSMINATION] =o leousso-o1 leouags-o | e5¢ ~S2 [COuSSO-O1OoUs4s-cG | SFR =OS [569153 01 [OoustS-o4 | 1 OM =O4 [SodSsO-01 [CodssS-08 [1 KR 705 [S95 20-01 [OauENS-55 | IOOY =ee |607752-c1 oouses-62l 10% =07 [S07T1S2-01 (OO G245-07/207 BOS

iw) ‘A Warner Communications Company

Super Breakout 5-13

Page 92

030 fer) #2 . 2 punces 55g MOVEMENT ego. WHEY ENERGHEED, one} 7 1280 en NI je 299 stanc pe t0

a je piu. AD-TYPL

May Core, (Pan Avorese-o1)

Se (eR) 2 PLACES NOTICE TO ALL PERSONS RECEIVING 7 product 209——4 a

NOTES: Dimensions shown are dim’s req'd. to Interchange & replace relay with existing equipment In field and production. re raprosuce hs draw

  • Break & deburr all sharp corners. iasion from the corporation
  • Dimensions taken from tooled part. Dimensions with * are specified dims. required in tooling by Englneering to have part Interchange with prior buyout part,
  • Coll data: 10 VDC +2, 50. resistance current 200 ma maximum.
  • Manufacturer: Coin Mech, Inc. Bt

DETAIL OF RELAY COIL (A007639-01)

Figure 5-6 Coin Lockout Assembly A030362-01 A

5-14 Super Breakout

Page 93

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction. forbidden without the Specitic written, permigsion of Atari, Inc.” Sunnyvale, Hifornia” This drawing 1s only conditions neither receipt nor possession thereof cont any right in, oF license to use, the subject matter of the drawing 0” any design oF technical information shown thereon, or any right to oroduce this drawing or any Bart thereo!, except for marulacture by vangors of Alar, near porated and for manulacture under the corporation's wt on tice 10 reproduce ths drawing is granted ‘OF he Subject matter thereof uniess by written agreement ‘with or written permission trom te corporatien,

ITEM PART NO. DESCRIPTION jary SWITCH MTG PLATE pases 165~441c SWITCH, OMRON C-5G3-3] 1 LMS, HOA HLGEE TAPING] 2. 4 fe-ua sala =} So COBB 24-01 WIREFORM ,cuerey | 1

Figure 5-7 Coin Switch Assembly A007640-01 D

Super Breakout 5-15

Page 94

NOTICE TO ALL PERSONS RECEIVING THiS DRAWING

nether recerpt nor possession ier ny CHORE 1m, OF Tee rawing ‘or any design or technical iformation shown Inerean, nor any sight ta reproduce iis drawing or any part thereot except for manuracture by vendors of Atari, Inco’ porated and for manutaclure under the corporation's wit fen license, no right to repaduce this drawing 's granted forthe subjéct malter thereot untess by written agreement ‘with or written permission from the cacparation

“D2 Rego , 10) ® ‘ @ oy

  • 4 REQD
  • 8 REQD
  • (9)

7 } ay le) aang 89 O° fo © /

~ ex

fe)

Prviris feos: oo) os ~ ux ©

O° ee ewe ie} = Q q a 2 q

Figure 5-8 Type B Power Supply Assembly A007197-01 D

5-16 Super Breakout

Page 95

Figure 58 Type B Power Supply Parts List

Part Number Qty Description

A009266-011Power Supply Base Weldment Assembly
2A006886-011Transformer Termination Assembly "Type B"
329-0531Cap., Sprague Electrolytic 26,000uf @ 15V
478-70501SC1Brkt., Cap. Mtg. Sprague #4586-48
5A006555-011P.C. Board Rectifier
779-44110045Fuse Holder, Panel Mounting
841-20031Filter, Power Line, 5 AMP
9A006958-C1A/RVolt Sel Block 95V
10A006958-02aVolt Sel Block 110V
ilA006958-03"Volt Sel Block 205V
12A006958-04"Volt Sel Block 220V
1378-27081Grommet ,Plastic
1472-1810S9Screw Pan Hd., #8-32 x 5/8"Lg.
1675-0489Washer, Split-Lock #8
1775-918Si;Nut Hex #8
1875-018S8Washer Flat #8
19A007192-011Power Switch Termination
20A007444-011Power In Harness
2146-2038011Fuse, 8 AMP, 125V, 3 AG Fast Acting
2246-2012512Fuse, 24 AMP, 125V, Slow Acting

© 4 warner Communications Company

Super Breakout 5-17

Page 96

Figure 5-9 Fluorescent Light and Speaker Mount Assembly A033261-01 C

5-18 Super Breakout NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction Torbidden. without 2 Sunny ‘This drawing is only conditionally issued at nor possession thereat conters or tansiers. any right i, oF license (0 use, th 19 oF any design or techni {mereon, nor any rightto reproduce ubject matter of the formation shown rawing or any part lure by vendors of Atari, incor nutacture under the corporation's writ 3 thereo! unless by written agre With oF written permission from the corporation.

Page 97

Figure 5-9 Fluorescent Light and Speaker Mount Parts List

ATARI’

Item Part Number Description

A009396-01 A005495-01 48-001 72-6810 A005819-01 72-6610 75-010S Assembly, Light & Speaker Board Assembly, 18" Flourescent Speaker, 8" Screw, Sht. Met., Pan Hd., Phil. #8 x5/8"Lg Assy, Light & Speaker Harness Screw Sht. Met. Pan HD., Phil #6 x 5/8" Lg Washer, Flat, #10 Re eH OPER 2

©@ 4 warne: Communications Company

Super Breakout 5-19

Page 98

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL” Reproduction forbidden without the ‘Specitic written permission of Atal, inc... Sunnyvale, Gaiitornia’ This drawing ts Only conditionally ‘ssued. and revther receipt nor possession thereat confers or transters ny right in, oF license to use, the subject matter of the Grawing or any design or technical information shown thereon, nar any “ight 1 reproduce this drawing or any part thereo!, except for manutacture by vendors of Atari, Inco porated and for manufacture under the corporation's wit. Fen icense, no righ 10 reproduce tis deawing 1s granted tortne subject mater thereor uniess by written agreement with or written oermission trom the corporation

Figure 5-10 Fluorescent Light Assembly A005495-01 A

5-20 Super Breakout

Page 99

Figure 5-10 Fluorescent Light Assembly Parts List

ATARI’

Item Part Number DESCRIPTION

193-104Gibson Fluorescent Fixture 18 inch
270-303Fluorescent Tube 18 inch (or Equivalent)
3A005493-01Fluorescent Light Harness
478-2652Grommet, Rubber
578-24001Tie Wrap
679-561816Wire Nut, Ideal 71-B
799-11006Lamp Socket Clip

oo 7 _ > Warner Communications Company

Super Breakout 5-21

Page 100

» NOTICE TO ALL PERSONS RECEIVING THIS DRAWING

  • CONFIDENTIAL: Reproduction’ forbidden without the 6 me ‘Sunnyvale, sued, and Any right in.oF ficonse 10 use, the 8Ubj Srawing or any’ design 2 techmcal- forma thereon. nor any fight toreproduce this drawing or ary part thereat, except Tor manulacture by Vendors o! Alar, tAcor porated and for manutacture under ‘i Dy written agreement wither wettten permission trom Me Corporation.

n x nA © yp 2 Cmanel Qo 9 z 8 2 No 7 -Tp- OM [ol

x 7 vOc—o 400-—o aomM 6 60 6 200 9 20O 9 2 emo 3 ea 2 ewe i 5 oa0— a) om 0 59m 0 Bee 8 3 90 g 20 x 90 joo

Olu

3PL

Figure 5-11 RF Shield PCB Assembly A033264-01 D

5-22 Super Breakout

Page 101

Figure 5-11 RF Shield PCB Assembly Parts List

ATARI’

Item Part Number Qty. Description oo

4030835-011P.C. Eoard
22D-101622 | Capacitor, Mono, 0.luf, 50V
341-300312 | Inductor, 100uH
452-00311 | Jumper, .600 Centers
575-E61060813 | Wingsorew, #6-32 x 1/2 Lg
675-9923023Fastener, 1/4 Turn, #6-32, Nylon
779-5172221Connector, 44 Pin P.C. Mount
8030868-012Mount, Connector

Super Breakout 5-23

Page 102

ues

Figure 5-12 Start Button Assembly A007357-06, 07 E

5-24 Super Breakout CONTROL PANEL NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specitic waitten_ permission of Atari, Inc.” Sunnyvale, Gioia’ This sawing 1s only conditionally issued, and neither receipt nor possession thereat conters or ransiers. (cense to Use, the subject matter of the ign or technical information. shown ny eight Yo repraduce this drawing or any par for manutacture by vendors of Atar, incor

fen license, no sight to reproduce this drawing 1 granted for tne subjéct mat ‘hereo! unless by written agreement ‘nith or wetten permission from the corporation

  • 2aPLcs

SOLDER AS REQUIRED 4 PLCS

uy PLCS

Page 103

Figure 5-12 Start Button Assembly \ Parts List ATARI

Item | Part Number Qty. Description

1006530-011Bezel
2006535-061Button (One Player Start)*
3006532-011Chassis
4A006533-011Switch Mtg. Plate Assy
579-43172Lamp Socket
670-11-472Lamp
762-0201Switch, Cherry, E68-50A
872-16036Mach. Screw, 6-32 x 3/16" Lg., Pan Hd., Phil.
982-88084Screw, Button Hd. Socket, 8-32 x " Lg., Black
1075-918S4Nut, 8-32
1175-0484Washer, #8, Split-Lock
12004577-192Jumper Wire, Black
1375-0466Washer, Split-Lock #6
  • Alternate: 006535-07 | 1 | Button (Two Player Start)

© Awarer Communications Company

Super Breakout 5-25

Page 104

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 105

NoISaan po NoISaaA go-

(oT ‘ONIMVUO SIHL DNIAIZOaY SNOSHSd TW OL SOLON

Treesurereeeiuenee ¥,90-@O10 if ni CNN BFE

Figure 5-13 Super Breakout PCB Assembly A033160-03, 04 A raz

Super Breakout 5-27

Page 106

MN Figure 5-13

Super Breakout PCB Assembly Parts List ATARI ® 03 Version Item Part Number Qty. Description 1 033161-01 1 P.C. Board 2 | 10-5101 1 | Ress, Car. Comps, 4, 5%, 100 OHM R43 3 10-5331 6 " 330 " R24,25,28,32,33,47 4 10-5471 4 470 " R18,21,29,31 5 10-5102 19 " " ” 1K " — R1-4,6,8,9,16,17,

19,20,22,23,26,41, 42546 45,51 6 10-5182 1 1.8K " R27 7 10-5472 4 4.7K 10-13 8 10-5562 1 " ” 5.6K " RT 9 10-5103 10 " 1 * 10K "RS, 30, 34-39 46,49 10 10-5332 1 Res., Car. Comp., kW, 5% 3.3K OHM R52 a | 19-315502 1 | Trim Poe, 5K OHM Roa 12 | 19-808W4PO 1 | Res., Wirewound, 4 OHM, 10¥ R50 15 | 24-250106 2 | Cap., Electrolytic, 25V, 10uf 630,47 16 24-250227 1 " " " 220uf cls 17 (24=250108 1 al " " 1000uf cn 18 | 24-250228 if " " 2700uf 54 19 24=250678 a ” “ 4700uf C55 20 | 27-250102 1 00luf Cd 21 27=250332 2 " =33ut C4546 22 | 27-250222 2]" stuf 048,49 23 | 27-250103 ij Oluf C4 24 27-250106 40 it - al " eluft €1-13,15-26,28,29,

32=38,40,42,43, 50-52

Ytem | Part Number _| Qty. Description 25 | 28101221 1 |] Cap., Dipped Mica, 100V, 220p£ ¢39 26 | 28-101102 1 || Cap., Dipped Mica, 100V, 100pf 627 27 | 29-010 1 |] Cap, Tantalum, 2.2uf 53 28 | 27-250473 1 |] Cap., Ceramic Disc, 25V, .047uf C56 a1 | 31-1N4001 2 || Diode, 1N4001 cR1,2 32 | 31-a1aF 2 || Diode, Alar €R3,4 36 | 33-2n3644 1 |] Transistor, 2N364% a 37 | 34-2N3663 3. |] Transistor, 203663 15,6 38 | 34-2N6044 1 || Trensistor, 2N6044 Q7 39 | 35-wcR106-1 2 |} Thyristor, MCR106-1 3,4 a 43 | 37-7402 1 |] Integrated Circuit, 7402 P2 4u | 37-7406 5 " "7404 3,84 ,H5,55,N9 45 | 37-7408 5 " "7008 B2,C2,N3,C5,A6 46 | 37-7410 1 " "7410 R7 47 | 37-7414 2 ca oU) A5,L9 48 | 37-7420 3 7420 16,A8,L8 49 | 37-7430 1 7430 Na 50 | 37-7432 4 1032 A2,12,P3,58 si | 37-7437 1 “7437 9 52 | 37-7474 3 " " 7aTe R1,J6,09 53 | 37-7487 1 oD 74874 RS 54 | 37.7475 1 . "7475 cu 55 | 37-7083 2 74683, Ls s6 | 37-7490 1 7490 6/7 57 | 37-74132 1 74132 10 58 | 37-74153 1 74153 8 59 | 37-74156 1 74156 8 60 | 37-7418163 6 || Integrated Circuit, 7418163 N5,N6,P5,P6,R5,R6

Super Breakout 5-28

Page 107

Figure 5-13 Super Breakout PCB Assembly Parts List 03 Version ATARI’ item | Part Number | @y. Desoription Part Number Description 1 | 37-7165 3 |} Integrated Cireute, 74165 37,787 97 | 90-102 1 |] ceyseat, 12.096 mz n 62 | 37-7166 1 " "1166 Ry 98 63 | a7-mi7% 3 “ " 7a176 F5,15,47 99 | 90-6010 1 || Microprocessor 3 64 | 37-7175 1 ” "ya175 Ne 100} 90-7001 8 || Ram, 2102-1 F3,H3,33,43,F4, 65 | 37=74367 4 " 14367 K/L3,E5,K5,E6 Ha, J4 Ke 66 | 37-9301 5 " "9301 D2, #2,P7,E8 KA tor oo | ar05i3 i : © aay - 102] 030868-01 2 || Mount, Connector 68 | 37-9316 5 ” "one R2,L3,"3,N8,P8 103 © | 37-9322 3 ” "9322 H2,32,K2 2m) Saleem 1 || Syme PROM “ $0 | sites 1 . «9330 i 105} 006401-01 1 |} Decoder E2 n | 37-1319 1 || Integrated Ctreuie, LMI19 uo 106 Ss | sabre i || saguteeor, 7512 & 107} 033280-01 1 || Super Breakout Playfield Char. PROM LS 4 aa | 37-7905 1 || regutaror, 7905 108] 033281-01 1 || Super Breakout Playftelé Char. PROM MS R& 7 | sraneiss 1. || ieaidweie, e903 109) 033282-01 1 |] Super Breakout Ball Picture PROM K6 75 | 37-Toa1004 1 || Auato amp, 7DA1006 v9 uo i ml ” 2 73 | e2-00, 1 || eéiecn esr, ean, BG 13} 033443-01 1 || Super Breakout Program PROM 3000 MS LO 79 | e6-118rir 1 || swtech sPst x8, DIP su 8/9 414} 033446-01 yo" “3400 MS MO 80 us} 03344501 ij) "3800 Ms NO ai 16} 033446-01 iff "300 Ms FO 82 | 72-1608 2 || Serew, Pan Hd. Phil., 6-32 x k Lg. CRES 117) 033449-01 ry" "3000 bs 83 | 75-016 2|| Washer, Flat #6 48) 033450-01 My" ean a4 | 752056 2|| Washer, Lock, Int. Star, #6 119), 03385101 yy" 3800 bs 85 | 75-9160 2 || Nut, Hex, 6-32, RES 120) 933452-01 ry" "3000 bs 86 1 87 122] 03344201 cs | "© 200 MS K/LO 83 | 78-0601 1 || Heatetnk (14323) 123. 89 | 7806022 1 || Heateink (7041004) 124) 033448-01 . . " . "2600 bs RI 90 | 78-13016 a/R |] Cement (TDA1004 Heatsink) 91 | 78-1605 1 |} stipad (um3229 96 | 79-42c40 1 || socket, 40 Pin, Med. Insertion 3

5-29 Super Breakout

Page 108

vedo suoueouranuon vem v SY

5-30 Super Breakout zsr0s = “enttyton'ge-2e eotst-ut | 09 euetiorettiio aT ow . «for wotosz-12 | 92 mm RTO" . » [Tt cotosz-zz | ez 69°87, 3M 0 ” z Uezase-uzf 2z go'sro EE z zecose-uz | 12 To 3nTOO" ow 1 zorosz-1z | 02 sso FR00L7 “ wo ft eLvose-2 | 6t

z

gu'sutga’saton'sn E9TSTYL IFROATD paaeszBeqy or gsi ow » aH sim ow “ ow wim ow L199 oor ow marl com ow ” Sim ow oy msm ow . enor Te ment 0 " ou enw . erttater'zv wr " ™ orm " er‘ev'or omm ow . or'sy vim ow . Le om ow “ ov'coten‘zotza wor ow “ oN'Se'sH' vata 90%L " “ ta wom ow “ oa 00% ‘37R2279 pervaBoquy gstvi-ce | 6s estre-ce | es zetre~ue | es osre-ee | 95 cere-ue | ss sem-ue | 9s resre-ce | €s mem-ue | 2 eerenee | 1s zene | 0s ocr-ue | oP ozm~ue | 89 oive-ue | ue otv-ue | 99 sor-ue | sy mor-ue | on Zom-ue | er $9 SRODZZ ow “ . ezzose-z | et Teo RQQDT ow . “ sotosz-nz | ct v9 3802 . . eezose-vz | 91 ent SMT tact ‘2Taktox308Tg ‘dep gotost-y2 | ST a el ose MOT ‘HHO y ‘punomerty ‘+say | 1 Oamngos-6T | 21 ona wHo ws eduray | 1 zosste-6t | 11 2S HHO HEE 4S My S*dulog rap f*8ey | T zees-ol | OT ertontec-ve foe ’sy ou NOT ow ono ” ” ot €0TS-OT on NS on wow |t z9ss-o1 e-ote xu"? a ZLns-o1 oomnue | on Leu 8° ooo ow fT zeIs-or

id Istsptootan ov I"tytoztez*zz*oz‘6r totus | 6 “CUT 6'etof ety ow XT ow ” ” et noonz-ve | Be Teer Tz ete Oy we ww “ « * evoenz-ne | ce wee'zeez cz yey ou OLE ww “ 9 Tees-O1 evpcuexe | 9¢ Emi WHO OOT ‘us ‘Hy ‘*duog “389 ¢ I Tols-ot ie pavog tora | 1 To-19Tee0

"© woRdo8eq “A

ec feu anty ‘opera || z ant-te | 2 Te TOOMNT ‘@PoTa Toomt-le | Te : wien ood RIVLV = 3S1] Seg ®

CLv0SZ~Le 82 Ayquiass 07 otorez | cz 19! V Gd WNoyeag uadns gE }-¢ asndiy

Zottot-ez | 9% Teztot~ez | sz

ea cc rd ware Zors-Ot Tevs-o1

“ed T-90THOK ‘F038 FAYE rn nognz ‘4orsyouray 9fs*TD ENOENZ ‘203s TeUeIy ry rene ‘4orsTsueay wrens qequnn weg | Wor

960 390" ‘ASZ ‘261q DTUEIag *-d¥y so 3nZ°Z fwnyequey ‘deo £29 34001 ‘a00t ‘PTH Paddtg ‘-ae5 6£9 34022 ‘A00T ‘¥>TH Paddy ‘dep enn woRdnoseq ° woqumn wed | wei

Page 109

ATARI’ Cs) n % ” an n Part Number

Figure 5-13 Super Breakout PCB Assembly Parts List 04 Version Description 37-6165 37-74166 37-761 76 37-76175 37=76367 37-9301 37-9312 37-9316 37-9322 37-93% 37-LM319 37-7812 37-7905 37-1M323 37-7DA1004 62-001 66-118P1T 72=1608C 75-016 75-056 75=916¢ 78-06001 78-06022 78-13016 78-16005 79=42C40 © A vere conmncatan company

Integrated Circuit, 74165 J7,L7,87 i "74166 R3 “ "rT F5,L5,A7 ” 74175 2 " “74367 K/L3,85,K5 26

  • “9301 D2,F2,P7,E8,K8 " "9312 9 " "9316 R2,L3,M3,N8,P8
  • “9322 H2,J2,K2 ” "9334 HB Integrated Cireutt, LM319 110 Regulator, 7812 ae Regulator, 7905 @ Regulator, LM323 ‘Audio Amp, TDALO04 v9 Switch SPST, Momentary SWZ Switch SPST x 8, DIP su 38/9 Screw, Pan Hd, Phil., 6-32 x & Lg. CRES Washer, Flat #6 Washer, Lock, Int. Star, #6 Wut, Hex, 6-32, CRES Heatoink (1M323) Heateink (7DA1004) Cement (1DA1004 Heatsink) Sttpad (1M323) Socket, 40 Pin, Med. Insertion C3

Item | Part Number | Qty. Description 97 | 90-102 1 |] crystal, 12.096 wiz v1 99 | 90-6010 1 || Microprocessor 3 100} 90-7001. || Ram, 2102-1 F3,H3,J3,K3,F6 HO,

3 Ks 102] 030868-01 2 || Mount, Connector 104} 006400-01 1 || syne PROM m2 105| 006401-01 1 |] Decoder Py 107 033280-01 1 || Super Breakout Playfield Char. PROM LS P4 108| 033281-01 1 || Super Breakout Playfield Char. PROM MS RU 108] 033262-01 1 || Super Breakout Ball Picture PROM K6 110] 933453-01 1 |] Super Breakout Program ROM 2800 c1 ai1| 033454-01 1]| Super Breakout Program ROM 3000 D1 112} 033455-01 1|| Super Breakout Program ROM 3800 E/FL

5-31 Super Breakout

Page 110

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 111

eur siyt Buoje nD ee a ee ee ee i Tape This Edge

Atari, Inc. P.O. Box 9027 Sunnyvale, CA 94086

L pjo4 puoseg

6Guyseulbug do-ulo9 ‘dnoiy suonesiyqnd -uny

980r6 Bius0p/eD ‘ajeaduuns 24206 X09 ‘O'd ‘oul ‘Wey

VO ‘ayeafuung POOL# Huda SSB1D IS44

plod ISM}

Page 112

Cut along this line

TM-118 1st printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A. If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name Firm — U Distributor 0 Operator Address ~ {) Other

City State Zip

Page 113

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 114

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 115

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation Or improper testing.

In no event shail Seller be liable for loss of profits, loss of use, incidental or consequential damages.

EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER.

This document is and contains confidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may noi be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 116

ATARI INC a » ATARI’ 1265 BORRE F SUNNYVALE, C 408/745