Complex-X Kit
Complex X (Taito America Corporation, 1984) · Kit Manual · 9 pages · 9 sections · original scan
C OMPLE X~ SC
COMPLEX-X 1s HERE !
Tae £-Peom kir Tuar Paves wro — Qu , Lookeerck, £Lzsctere YoYo oe Stice Dyy Geen
(7 Paves Kear fro THe Bonen ! No GOL0ERING or WIRINE |! Fasr Pay Aeron / Grr Eanis Our OF Tae BReacrok Bevoes Ha Drowns /v Rapioacrive Soup / hoe Our hoa Tioss Nasty Nvesean Bues /
MANUFACTURED UNOER LwtWSE FROM £7. We. By —
es ERD oe Ssute T kk CAJON, CA. (2020 C19) 449-9010
PGD, INC.
COMPLEX-X Installation Instructions
Remove all EPROMS IC 4 through IC 19 and IC 27 from ROM I/O PC board.
Replace with COMPLEX-X ROMS U 6 thru U 10, U 15 thru U 19.
Remove U1, U 22, U 29 from ROM I/O board.
Replace with jumper plugs provided with kit. Make sure pin 1 is in the proper position. Pin 1 is denoted by notched corner of plug.
Remove U 24 and replace with the Pal chip provided with the kit.
Remove 4-way joystick, 1 and 2 player buttons, slow and fast draw buttons.
Remove control panel lexan. Replace with new lexan provided in kit.
Install new 8-way joystick, 1 player, 2 player, and fire buttons provided in the kit.
Remove marquee glass. With a razor blade, scrape alI paint off glass. Install COMPLEX-X overlay on blank glass using soapy water. Wet the glass lightly with soapy water, peel the protective backing off the COMPLEX-X decal and place the decal on the blank glass. The soapy water will allow you to position the decal properly, Let dry and trim excess. Reinstall COMPLEX-x marquee into game cabinet.
1985 Friendship Drive, Suite J ¢ El Cajon, California 92020 * (619) 449-9010
STANDARD COIN SETTINGS
s/2/2 slslflelale
4|3|8|2|8|8/ 8 COIN DOOR MECHANISMS CREDIT/MONEY _
| STANDARD | 7.25.41 | or | or | 04 | +a 00 |
| , | 11.50, 31, 642 | 02 | o1 | 04 | [04 | 00 |
| 7.50 | 03 | ot | 04 | 00 | 00 | |
| 1 DM, 5DM | 10M, 6/50M | 04 | 06 | 00 | 00 | 00 |
1 FRANC, 5 FRANC [er 3/5 ONLY [0s [01 | 36 00 | 00
| 25 CENTS, 1 GUILDER | 1725, 4G | 06 | or | 00 | 00 | 00 | ||
| 5 FRANCS, 10 FRANCS | WF, 2n0F | 7 | or | 00 | 00 | 00 | ||
| . | TAOF | 08 | ot | 00 | 00 | 00 | ||
| 1 FRANC, 2 FRANC | 2, 5/2F | ; | 09 | 00 | 04 | 00 | 00 | |
| TUNIT, 5 UNITS | 12, 35 | 10 | 01 | 00 | 00 | ||
| TWIN COIN | 11 COIN | ; | or | o1| | 04 | 00 | 0 |
| 12 COINS | 03 | 01 [ 04 | 00 |
CUSTOM COIN SETTINGS
s|ls)s
Zl els E 8/5 B(8)2/2/e/2)3
Bz =| €
| a|5|s{2|8| | 8] | § |
| COIN DOOR MECHANISMS | CREDIT/MONEY | [ {[] |
| STANDARD | 11.25, 51 | 04 | “00 |
4.50, 5/41 04 | 02 |
| 2.50, 4/81 | wo} | o | |
1.50, 341, 41.25 15 { 00 | 1.50, 381, 782 96 | 24
| 20 CENTS, 1 GUILDER | 7.20, 3/.50 | 00 | 00 | |
| 25 CENTS, 1 GUILDER | 1.25, 5/1G | ul | oo | |
| 100 LIRE, 200 LIRE | 1/200 LIRE | 00 | 00 | | |
| TWIN COIN | 13 COIN, 2/5 | 00 | 00 | |
| 1 UNIT, 3 UNITS | 1, 5/5 | 00 | |
| 13, 25 | oo} | oo | |
POWER ON/OFF SWITCH, INTERLOCK SWITCHES, MEMORY PROTECT SWITCH, SELF TEST SWITCH, VOLUME CONTROL, ANO SERVICE QUTLET To minimize the hazard of electrical shock while servicing the game a Power ON/OFF Switch, and two (2) Interlock Switches are provided. Two (2) Self Test Switches, a Volume Control and a Service Outlet have also been provided. (See Figures 5 and 6 for location of Switches).
1 POWER OWQFF SWITCH, INTERLOCK SWITCHES A Power ON/OFF Switch Is located in the front of the game at the botton left side of the cabinet. There are two Power Interlock ‘Switches, one is located on the inside of the Coin Door, the other ‘switch is located at the inside rear of the Service Door. This switch removes all the power from the game without unplugging it from the wall outlet. Power may be restored for servicing by pulling out on the interlock Switch Buttons.
Ca
XN
FIQURE 1-2 POWER ON/OFF SWITCH
2 MEMORY PROTECT SWITCH The Memory Protect Switch is used to prevent erroneous writes to
beaten in the CMOS RAM which store the location program
variables.
Coin Geer Memory Pretest Switch
Coin Deer Power interinek Switch
= Beek Door Prwer intarioek Switch
FAQURE 1-3 INTERLOCK SWITCHES & MEMORY PROTECT SWITCH
3 SELF TEST SWITCH There are two (2) Seif Test Switches and four (4) positions, :ocated on the inside of the Coin Door. See Figure 5. The “QiX""™ game is capabie of testing itself and provides data to demonstrate that the games circuitry and the controls are working properly. For further Information on the Self Test Procedure reter to Section 1.8 and Pyure 1-8.
zt
SELF TEST SWITCH SWITCH FUNCTION Up Reset To Factory Setting (Reset Line Lit) Increment Number (Variable Line Lit) Decrement Number Move To Next Line Move To The Next Screen
SELF TEST SWITCHES
4 VOLUME CONTROL SETTING The Volume Control Setting is located on the Data/Sound P. C. Board, which is on the rear of the Service Door. The volume increases when turned clockwise as indicated in Figure 1-5. Down Advance Sub-Test Advance Test
VOLUME CONTROL SETTING 5 SERVICE OUTLET A Power Recepatacle has been provided to further aid servicing. The voltage at this receptacle will be the same as the line voltage the game Is set at.
6 ELECTRONIC ACCEPTORS This game is equipped with the capability of using 12VOC Electronic Coin Acceptors, such as Third Wave Electronics, Model TW12 or equivalent. Power for these units may be obtained from the Coin Entry Lamp terminals which provide 12VDC.
7 COIN METER This game is also equipped with the capability of using a Coin Meter. See Illustration below. Connect one lead to the + 12VDC supply (available from the Coin Entry Lamp), another connection from the other lead on the Coin Meter to Connector J15-13 on the ROM/IO Board
+12V00 415-13
SELF TEST PROCEOQURE GENERAL The Seif Test Procedure is performed using the two (2) Switches located on the inside of the Coin Door, and the Self Test Button and the LED'S on the Video PC Board. (See Figure 1-7).
‘SELF TEST BUTTON
2 ENTERING INTO THE SELF TEST MODE To enter the Self Test Mode, press the Advance Sub-Test Switch on the Coin Ooor or the Self Test Button found near the LED display. All the LED'S should blink on and the Hardware Tests should start. The Diagnostics can be entered at the Location Programming Screen (Section 1.8.16) by pressing the Advance Test Switch on the Coin Door.tt a continual test of the Video Board is desired, press the Self Test Button twice to start the Video Test in the Auto Test Mode. In this mode, the machine will continually run the Hardware test until powered off. if the message “OPEN COIN 000A TO TEST” appears the Coin Door must be opened oF a jumper connected across J19, 1-2. This is because the CMOS RAM Test (Section 1.8.6) cannot be performed with the memory protected by the Coin Door Switch. :
3 HARDWARE TESTS These tests are performed in the following order:
VIDEO BOARD DATA BOARD. ROM Checksum ROM Checksum Communications RAM local RAM Communications RAM Handshake Test
HARDWARE TESTS
All LED values are shown Left to Right. 0 is OFF, 1 is ON and X is dependant upon the test results.
4 VIDEO BOARD ROM CHECKSUM The ROM Checksum calculates the checksum of each Video ROM and compares it to the checksum stored for that ROM. If it differs from the stored value, the machine will halt and the value of the ROM with the bad checksum will be shown on the LED'S.
LED VALUES: TEST IN PROGRESS: 00 0001
FAILURE: 01 XXXX
LED VALUE] VIDEO OT 0000 WA Us 0% 0001 01 0010 01 0011 0% 0100 01 0101 01 0110 010114 01 1000 01 1001 01 1010 01 1011
{f the Checksum ROM is bad, it will show U10 to be bad first. If this test fails, the ROM indicated on the LED display will need to be Teplaced. The E-PROM Memory in a given game may be implemented as banks of either 2716 or 2732 €-PROMS. The E-PROM type for each bank is selected by the decoding jumper 26-00002-016 for 2716 or 26-00002-032 for 2732. E-PROMBANK _|___——LOCATION_ Ui VIDEO DATA u22 SOUND u29
- DECODING JUMPER LOCATION
5 COMMUNICATIONS RAM FROM VIDEO BOARD The Communications RAM Test determines the stability of memory shared by the two processors by storing a predefined series of numbers throughout the RAM, then reading it back to insure that it was stored correctly.
LED VALUE: 00 0010
A failure has been detected when the machine halts with the above display. Failure of Communications RAM during Video Board Tasts may resultfrom either defective RAM circuitry or failure of the Oata Board. To isolate the failure, disconnect the Data Board at P6 and re-enter the test. A tailu7e means trouble in U3, U4 or associated circuits. Passing the retest suggests Data Board problems. ~
6 VIDEO BOARD CMOS RAM After saving values in another portion of memory, the CMOS RAM is tested in the same manner as the Communications RAM. If the CMOS RAM passes the test, all of the locations are restored to their previous values.
LED VALUE: 00 0011
A failure of the CMOS RAM has been detected when the machine halts with the above LED value displayed. If this occurs U85 and U86 or associated decoding should be checked.
7 VIDEO BOARD COLOR RAM This tests the system Color. RAM by storing predefined sequences of numbers in the Color RAM, then reading them back while testing for accuracy.
LED VALUE: 00 0100
A failure is indicated by the processor halting with the above value displayed on the LED'S. This signifies the need to check U56, US7 and associated multiplexing and decoding.
8 VIDEO BOARD SCREEN RAM The Screen RAM |s tested by writing a pattern to each page on the screan. The results of these writes is then compared to the original pattern. Any discrepancy causes the machine to halt with the LED displaying the faulty RAM.
LED VALUE: TEST IN PROGRESS: 00 0101
FAILURE: 1X XXXX
Leo vaLug RAM [11 xxxx | RAM | 10 9000 U33 110000 10 0001 11 0001 10 0010 11 0010 10 0011 110011 10 0100 11 0100 10 0101 110101 10 0110 11.0110 10 0111 110111 10 0000 11 1000 10 1001 11 1001 10 1010 11 1010 10 1011 111011 10 1100 11.1100 10 1101 111101 10 1110 11.1110 10.1111 111111 VIDEO BOARD RAM CHECKSUM
Upon failure of a screen RAM, locate the problem RAM and replace it \f this Diagnostic appears to halt without indicating a RAM failure (000101 on LED'S), a failure to begin the next test (Data Hardware) Is indicated. The interconnection to the Data Processor must be inplace and the Data Processor must be functional to continue.
VIDEO BOARD (ON BACK SERVICE DOOR)
1.8.9 DATASOUND BOARD SELF TESTS DATA HARDWARE (ROM CHECKSUM) The ROM Checksum calculates the checksum of each Data ROM and compares it to the checksum stored for that ROM. If it differs from the stored value, the machine will halt and the value of the ROM with the bad checksum will be shown on the LED'S.
LED VALUE: TEST IN PROGRESS: 00 0110
FAILURE: 01 XXXX
LED VALUE 01 0000 01 0001 01 0010 01 0011 01 0100 01 0101 01 0110 01 0111 01 1000 01 1001 01 1010 01 1011
DATA/SOUND BOARD ROM CHECKSUM
If this test fails in the field, the bad ROM will need to be replacad.
10 DATA/SOUND BOARD LOCAL MEMORY The Data Processor uses a known sequence of numbers to test the bits in its Local Memory. If a bad bit is found the machine will halt with the following display.
LED VALUE: 00 0111
11 COMMUNICATIONS RAM ADDRESSING The function of this test is to ensure that both the Data and the Video Processor address the Communicatons RAM in the same manner. The Data Processor requests the Video Processor to fill the RAM with @ known pattern then, the Data Processor compares the result to the expected pattern. if it does not match, one of the processors is probably decoding the address incorrectly as the RAM itself was previously tested for stability by the Video Processor. The machine will halt with the following display.
LED VALUE: 00 1000
12 DATA/VIDEO HANDSHAKE . This test ensures that the Data Processor can send priority commands via interrupts to the Video Processor. The Video Processor is halted, then restarted by the data Processor after the proper command acknowledgements are received. The machine will halt with the following display.
LED VALUE: = 00 1001 14 ALIGNMENT AND CONVERGENCE TEST This screen is provided to align the color guns and correct the convergence on the screen. The screen is composed of a red and a green rectangle and white grid. Adjust the screen width and length so that the red rectangle is slightly within the boundaries of the tube. The adjustment is to be made on the center of the lines which make up the rectangle. The corners of the rectangle will extend beyond the shadow mask. The green rectangle defines the normal playfield and so should be visible from the players view point. A grid of white squares is provided to help detect and correct any convergence problems the tube may have. Adjust the monitor until the squares are of equal size throughout the screen. To advance to the next screen, activate the Advance Test Button on the Coin Door.
non LOCATION PROGRAMMING SCREEN(LANGUAGE SELEC- This screen allows the user to select the language in which the Location Programming and the game will operat. Four (4) lanu"ges are provided. Use the Advance Sub-Test Button to move
non LOCATION PROGRAMMING SCREEN(LANGUAGE SELEC through the offered languages. When the desired language is
Qreen, depress the Advance Test Button, to advance to the next screen.
16 LOCATION PROGRAMMING This screen allows the location to define the difficulty factor for the game. It also allows ‘the location to set a maximum number of Credits allowed in the machine prior to a game start up. The user selects the line to be changed by using, the Advance Sub-Test Button until the desired line is changed to green. The value associated with this line is then modified with the UP or DOWN Switches. If the machine is to be reset to the factory settings, use the Advance Sub-Test Button until the reset line is lit in green, then press the UP Switch. The values will be reset and the user will be placed back on the first line for futher adjustments. Advance test will move to the next screen at any time. The backup HSTO (High score to date) value is used to reset the high score on the next screen. Its value will initially determine the Score needed for a player to have his own initials show with his score in the high scores. The maximum credit defines a limit for the machine, which when crossed will disable the coin slots. This allows the location to set a limit on the amount of games a player will get if there is a line of people waiting. This value ranges from 1 to 99. However, it should Not be set So close to 99 that a single coin can overflow the credits issued (maximum 99). A Free Play Mode may be selected by Setting maximum credits to 0. The credits per coin are set in the coin slot programming screen.
17 HIGH SCORE TO DATE SCREEN This scraen shows the scores and initials of the players with the ten highest scores. It is used as an audit for the game. To reset the values to the backup HSTD selected on the previous screen, press tha UP Switch. This will also set the initials to “TAC”. When the UP Button Is activated it resets to default scores. To
cone Ad the next screan, activate the Advance Test Button on the
ir. p 18 AUDIT TOTALS This screen provides the audit totals for the game. Once they are recorded, they may be zeroed by pressing the UP Switch. The following audits are kept. Total Credits The total number of paid credits issued: This total is never zeroed, but it will wrap around to zero when its total reaches 1,000,000. The only time this total can be zeroed is by physically removing the battery or jumper W1, while the power is off. The number of coins dropped into the left slot. The number of coins droped in the center slot. The number of coins dropped into the right slot. The number of credits issued for coins. The number of credits awarded by the game. Awarded credits / paid credits + awarded credits *100 Number of minutes the game has been in play mode. Number of minutes the game has been in extended or awarded play. Awarded minutes / minutes played “100. Minutes played / paid credits + awarded credits *60 The number of times which a player scored high enough to bump someone else from the high score list. Left Coins
Center Coins
Right Coins
Paid Credits Awarded Credits
% Free Plays
Minutes Played
Minutes Awarded
% Free Time Average Game (Sec)
High Scores
AUDIT TOTALS
The UP Switch is used to zero the audits. To advance to the next Screen, activate the Advance Test Button on the Coin Door.
19 COIN SLOT PROGRAMMING This screen allows the user to either select a standard coinage setting for the game or program his own. If a Standard setting is desired, use the UP and DOWN Switch to adjust the coinage setting white it is lit in green. The values for the variable will change as this ‘umber is altered. When the right selection is set, use Advance Test to return to the game. 't a non-standard setting is desired, use Advance Sub-Test Switch to move down to the variables so that they may be programmed individually. Once this switch is pressed, the setting number Is set tozero to show that the location has supplied their own settings. As the lower variables are unchanged, the user may minimize his effort by first selecting a setting close to the one he desires. Once in the programming mode, the Advance Sub-Test Switch is used to move among the variables. It will also take you back to the standard settings, if you press it by mistake. The UP and DOWN Switches are used-to increment or decrement the values. Advance Test Switch will return to the game when pressed. The coin multiplier tells how many coin units are issued for each coin through a particular slot. Coin units for credit show the fumber of units necessary before a credit is issued. Coin units for
pons gives the number of units necessary before a bonus credit Is
issued. Minimum coin is an optional value which will keep the credits from accumulating until the specified minimum amount of coin units is Teached. It is not used in any of the standard settings.
20 CMOS MEMORY FAILURE If the message ‘*Memory Failure - Service Required” appears on the screen, the CMOS RAM which stores all of the location prog-
ramming has failed. All the values stored in the RAM are set back to
factory defaults. This condition probably indicates a battery failure,
“8 GG86 GEQEBARE * 88 @BRERG RBaa * a} RGRRBRRRBEE aReRBRAREE Be .. BEERBERERE ee | (EGE BBRERBEE B Beeeeee ”
F Ge) i
[x1] I we rn] [3] —_] [r+] ‘ Raa
eee 8 aaeees salsa = all ce cD ce (x3) cD cm fees] (a) 3} =] ee) Ge) ic (=) icy 7] aq aRGERRRE GERRBSEBBEB BBE ” BH BBBBE A B aan =D een OD OD eg TOU rev NOC HD %en GD an OD ee 0 in GD ten WOU $,7€LZ ere ET-n Ybnozy3 E-N: cc ROM V0 P.C. ASSEMBLY
com oon comme, rom, Lfzsiseresuna r2acse789m ND
a # amor WIRING DIAGRAM