CATHODE RAY TOMES

Speedfreak

Speed Freak (Vectorbeam, 1979) · Manual · 74 pages · 79 sections · original scan

Page 1

VECTORBEAM

OPERATION and MAINTENANCE MANUAL

Page 2

Speed

| Freak

VECTORBEAM

33441 CENTRAL AVENUE UNION CITY, CA 94587 (415) 489-2000 OPERATION AND MAINTENANCE MANUAL

Page 3

PROPRIETARY NOTICE

The contents of this manual are the Property of Vectorbeam and are not to be copied or reproduced in any manner whatsoever, nor disseminated in any form to any person who is not a Vectorbeam user without the permission of Vectorbeam.

Copyright © 1979 by Vectorbeam Inc.

it

Page 4

TABLE

OF

CONTENTS

1GAME SET-UP

GENERAL. : INSPECTION . : INSTALLATION. : AC Line Voltage Selection. .. PRELIMINARY CHECKOUT PROCEDURE ... INTERLOCK SWITCH CHECKOUT PROCEDURE OPERATOR OPTION SWITCHES

2GAME DESCRIPTION

GENERAL.. Attract Mode . Ready-To-Play . Play Mode ... +223

3 THEORY OF OPERATION

GENERAL. + 3-2 GENERAL DESCRIPTION. 3-2 MONITOR DISPLAY ....... 3-2 THE VECTOR GENERATOR . 3-5 THEGAMELOGIC .. 3-5 Program Memory ....... 35 ‘The Program Address Counter 3-10 Program Memory, Data Bus Multiplexing . . 3-10 The Instruction Register. . 3-10 The Data Register....... 3-10 Working Storage, Address Selector and Register 3-10 The Data Selector .........- The Computation Circuitry . The Audio Board. . . Steering Control . PROM Board

iii

Page 5

4 MAINTENANCE

GENERAL DISPLAY MONITOR ADJUSTMENT PROCEDURE Volume Control Adjustment . . Test Pattern Recal Procedure . Test Pattern Adjustment Procedure . X and Y Gain Adjustment . Centering the Display : Steering Assembly Adjustment Procdure. Shifter Assembly Adjustment Procedure . PR WEP YY yw oe pu

CONTROL PANEL REMOVAL ...... 3-4 PLEXIGLAS SHIELD AND RETAINER REMOVAL. 3-4 Retainer Removal ... . 3-5 Retainer Replacement . +35 Shield Replacement . 3-5 Troubleshooting ... 3-7

5S ILLUSTRATED PARTS BREAKDOWN

LIST OF APPENDICES

APPENDIX A Reference Schematics

LIST OF ILLUSTRATIONS

Figure 1-1 Vectorbeam Speed Freak Game Major Component Locations 20.00.0000 ccc cece aces eceeceesetutuss 1-2 Figure 1-2 Speed Freak Game PCB Assembly Locations Figure 1-3 Speed Freak Control Pane. Figure 1-4 Rear Access Panel ...... Figure 1-5 Power Supply Voltage Selection Figure 1-6 The Interlock Switch Location . Figure 1-7 CRT Filament Location..... Figure 1-8 Operator Option Switch Settings Figure 2-1 Attract Mode Screen Display . . Figure 2-2 Ready-To-Play Mode Screen Display Figure 2-3 Play Mode Display Figure 2-4 EXTRA Time . Figure 3-1 General Block Diagram of Speed Freak Game... 0... e cc cc ees et neta edteetutnesesusevenes 3-3

Page 6

Figure 3-2 Figure 3-3 Figure 3-4

Figure 3-5 Figure 3-6 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 4-7 Figure 4-8 Figure 4-9 Figure 4-10 Figure 4-11 Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4

Table 1-1 Table 4-1 Block Diagram of Logic PCB. Block Diagram of Vector Generator Simplified Block Diagram of the Display Electronics PCB (one-half analog section) 2.2.2... ccc ccc cece cece cette eee e eee e en es 3-7 Simplified Block Diagram of the System Sequencer Display Section... Simplified Block Diagram of the Line Length Timer Test Pattern Display ain CRT Magnetic Centering Rings Location . Steering Wheel Film Set- Up a and nd Adjustment Shifter Bar Magnet . Control Panel Removal... ; Plexiglas Shield and Plex Retainer Removal..... Display Monitor PCB Testpoint and eens Layout Logic PCB Testpoint and Adjustment Layout. . Audio PCB Testpoint and Adjustment Layout... Steering PCB Testpoint and Adjustment Layout . PROM PCB Testpoint and Adjustment Layout... Heatsink Assembly Yoke Assembly ..... Coin Mechanism Assembly . Power Transistor Wiring. .....++

LIST OF TABLES

AC Line Voltage Selection. Troubleshooting Charts... 00ccsceevceereevne

Page 7

ECTORREAM ~ Cowmmrey “Rae: | WREGH FER meen Sree Fr

Page 8

GENERAL

This chapter describes your Vectorbeam Speed Freak game, the selected location for your game, and how to inspect it. It also outlines the preliminary set-up procedure. The Vectorbeam Speed Freak game is a colorfully illustrated upright video game which appropriately justifies the vector display technology creating the illusion of a three dimensional roadway filled with exciting obstacles such as opposing vehicles, roadside objects and much more. The Speed Freak game is a single player first-person driving game with the front-end of the player’s vehicle displayed onto a curving roadway which disappears into a vanishing point. As the player depresses the accelerator pedal, the vehicle heads toward cactus, hitchhikers, bridges, flying airplanes and other objects as they begin to appear faster and faster as the player increases his vehicle speed The object is for the player to avoid the objects on or off the road with a speed as fast as his skill allows. A more detailed game play is located in the Game Description chapter of this manual.

CONTROL PANEL

POWER SUPPLY CHASSIS

ACCELERATOR PEDAL The major components of your Speed Freak game are illustrated in Figure 1-1. These major components are the following:

coin mechanism © vector monitor chassis © power supply chassis control panel © accelerator pedal all PCB assemblies

The PCB assemblies of the Speed Freak game are contained in the game cabinet. These components are listed in the following:

© Game logic PCB e Vector TV monitor PCB @ Audio PCB © Steering PCB Shifter PCB ¢ PROM PCB (temporary)

PCB ASSEMBLIES

COIN MECHANISM

Figure 1-1 Vectorbeam Speed Freak Game 1-2 Major Component Locations

Page 9

The operator control panel, as illustrated in Figure 1-2 is comprised of the four-speed gear shifter, the steering wheel and the start button.

INSPECTION

All Vectorbeam equipment is carefully packaged in well padded cardboard containers to prevent damage during shipment. If a component is noticeably damaged, notify the Vectorbeam Customer Service department for information concerning the disposition of the damaged component. To avoid cancellation of the warranty, DO NOT apply power to the game.

NOTE

For kit information refer to Appendix B. (Supplement to be mailed later.)

STEERING WHEEL To ensure that the equipment has suffered no damage in shipment inspect the container prior to acceptance from the carrier. If no immediate cabinet damage is evident perform the following visual inspection.

  • Remove the rear access panel with the appropriate packaged key (refer to Figure 1-3).
  • Examine each major and electrical component thoroughly for scrapes, dents, broken or missing parts and loose or missing screws
  • Check for loose cable connectors.
  • Visually verify that all the integrated circuit devices (IC’s) plugged into sockets are properly seated and that no IC pins are bent or misaligned.

Should any damage be discovered during the foregoing inspection, a claim should be filed with the carrier. A complete report of the damage should be forwarded to Vectorbeam.

GEAR SHIFTER

Figure 1-2 Speed Freak Control Panel

1-3

Page 10

Figure [-3, Rear Access Panel

INSTALLATION

Planning the location of the game should involve both physical and electrical consideration. Physical considerations concern the placement of the equipment with respect to clearances, AC cable and environmental conditions such as ventilation, temperature, weight support and accessibility (although your game has the durability to endure nearly every type of physical hazard). Electrical considerations include availability of the correct voltage and frequency In planning this installation, consideration must also be given to working space required for personnel involved with operation or maintenance of this system

NOTE

The cabinet must be within five feet of an AC outlet. Be certain that a ground jack or terminal is available at the outlet.

1-4

CAUTION

Warranty void when the AC ground prong is broken off the plug.

AC Line Voltage Selection AC line voltage selection is available in your Speed Freak game by setting the appropriate jumpers on the power supply chassis, Table 1-2 lists the selectable jumpers for either 100 VAC, 115 VAC or 230 VAC. Always check for the correct AC line voltage with an AC voltmeter at the AC outlet.

TABLE 1-2 AC Line Voltage Selection

Input Jumper Input

Voltage Terminal Connection

100 VAC 11S VAC 230 VAC Tto2,3to4 1to 2, 3t04 2t03

PRELIMINARY CHECKOUT PROCEDURE

The Speed Freak game, after it is properly installed, should be checked operationally by performing the following procedures:

  • Plug in the AC jack into the AC outlet.
  • Allow 1 to 2 minutes for CRT warm-up. () Observe the TV monitor display to assure the correct Attract mode is present on the screen (the Attract Attract. mode is explained in detail in the Game Description chapter)
  • If the Speed Freak Attract mode display is incorrect, refer to the Maintenance chapter.
  • Insert quarter into either slot of the coin mechanism, Attract mode should disappear and the game should be in the Ready-to-Play mode as described in the Game Description chapter.
  • Proceed to play the game and verify that all screen images are displayed as shown in the illustrations of the Game Description chapter.

If adjustments are necessary refer to the Maintenance chapter. oo ora

Page 11

INTERLOCK SWITCH CHECKOUT PROCEDURE

The interlock switch (Figure 1-4) has been provided by Vectorbeam to effectively secure a safeguard for the maintenance technician, while working inside the cabinet. This interlock switch should be checked for precautionary purposes by performing the following procedures while power is supplied.

  • Unlock the rear access door but do not remove it.
  • Slowly pull the upper half of the rear access door until the CRT filament (see Figure 1-5) indicates the absence of AC line power.
  • If the CRT filament of Step 8 is not lighted check the fuse on the power supply, the interlock switch and power cables.
  • Close the rear access door, wait a couple of minutes and the monitor should display in the Attract mode.
  • Lock the rear access door and reposition the cabinet to its permanent position.

The AC power to the game may be applied when the rear access door is removed by pulling out the interlock plunger. illustrated in Figure 1-4

INTERLOCK SWITCH

Figure 1-4 Interlock Switch Location FILAMENT

Figure 1-5 CRT Filament Location

Operator Option Switch

‘The operator option switch is a two toggle DIP device located on the logic PCB. The photo of Figure 4-9 indicates the exact location. The DIP toggle settings are illustrated in Figure 1-6. A double coin jumper option is available to the operator It is located on the audio PCB. Extra time is 3/8 of the game time.

GAME TIME PER COIN

60sec 90sec 120sec 150sec

Figure 1-6 Operator Option Switch Settings

Page 12

Game D

escription

Page 13

GENERAL

The Vectorbeam Speed Freak game has all of the controls a player needs to feel totally in control of his own vehicle on a country roadway. The three dimensional visual effects are only a portion of this game’s realism. The exciting audio simulates the sound of a racing car, the shifting of gears and screeching tires on pavement as the vehicle skids off the road or while swerving out of the way of a road obstacle. The following paragraphs explain the different game modes needed to be checked after either set-up or repair to ensure that it is operating properly.

Attract Mode Figure 2-1 The Attract mode appears on the TV monitor screen 1 to 2 minutes after the AC power is applied. The Attract mode consists of a three dimensional two lane straightaway more or less center screen. The front portion of the player’s vehicle appears at mid-lower screen which creates the first person ffect. This vehicle is superimposed on to the right

HIGH SCORE

Figure 2-1 Attract Mode Screen Display lane as it speeds down the roadway. An occasional road sign, cow, bridge or hitchhiker is passed by the unattended vehicle, The 3 digit high score is displayed in the upper right hand corner of the screen and the current score is presented in the upper left hand corner. The high score is zero when AC power is initially applied, otherwise the high score displays the last highest score. This high score is reset each time power is removed then reapplied. The player controls remain inactive and the LED pushbutton switch is dark

Ready-to-Play Mode

Figure 2-2 The game is set into the Ready-to-Play mode immediately after the coin or coins are inserted. When the coin switch is activated by the coin the game is set into the Ready-to-Play mode. The TV screen displays the attract mode images plus the extended play options approximately mid-upper screen. The controls remain inactive while the LED pushbutton switch is flashing

HIGH SCORE

SCORE — PUSH START

EXTRA TIME AT 099

Figure 2-2 Ready-to-Play Mode Screen Display

Page 14

Play Mode Figure 2-3 The play mode is triggered when the player presses the flash LED pushbutton located at the left hand side of the control panel. The TV screen instantly displays a curved roadway. The front portion of the player’s vehicle remains motionless on the right hand until the accelerator pedal at the bottom of the game cabinet is depressed as illustrated in Figure 1-1. As the player continues to depress the accelerator pedal, the vehicle begins to accelerate, while moving on the screen corresponding to the steering control. The shifter at the right hand side of the control panel should be in first gear (labled). The game simulates engine wind-out in each gear. The player has complete control of his car as it races against the clock at a speed equal to his skill. The clock in the upper left hand corner counts off the player’s driving time in seconds. The clock is set at the beginning of each game according to the switch option available only to the

Figure 2-3 Play Mode Display operator. The player can extend his time when reaching a score set at the operator option switch. The player's current score is displayed in the upper left hand corner. Each time the player reaches the extended time score, the words “EXTRA TIME”’ are flashed on the upper mid portion of the screen, as illustrated in Figure 2-4. The clock continues to run, giving the player points until the car runs off the road or hits an obstacle. Each time an accident occurs the clock stops until the crash display terminates and resets the display to a normal game mode as illustrated in Figure 2-3. Either of the two thrilling accident scenes are displayed on the screen. One crash scene appears every time the player’s car skids off the road or hits an obstacle other than a police barricade or an on-coming car. The other scene appears whenever the on-coming car is hit or when the player's car rams the police barricade. An audio warning of a possible accident is sounded by the screeching of tires or the horn of the opposing car when the player’s car crosses into the left lane.

SCORE EXTRATIME TIME

Figure 2-4 Extra Time Mode Display

Page 15

THEORY

OF

OPERATION

<— Intake mawi Fou &— CARBURATOR

Page 16

GENERAL DESCRIPTION

This chapter describes the principles of operation of the major circuit functions of the Vectorbeam Speed Freak Game. The system’s general functional description is followed by detailed circuit descriptions. Each circuit description includes simplified circuit schematics (Appendix A) applicable to the blocks under discussion. Note that all of the schematics used are very similar to the schematics used by most industrial electronics firms. The use of the wide arrowhead paths simplify the schematic bus lines.

Figure 3-1 illustrates all of the major components of the Vectorbeam Speed Freak game. This block diagram indicates that the logic board is separate from the monitor. It also illustrates the low voltage power supply package, the coin mechanism, the control panel and how they are interconnected. Figure 3-2 illustrates the logic board block diagram. The dash lines indicate what is used and shared by the monitor display electronics. It also indicates that which is to be only used by the display electronics on the monitor board.

MONITOR DISPLAY

(Refer to Appendix A, Figure A-1) All monitor electronics are self-contained on a single printed circuit board. All low voltages supplied to this board originate from the power supply package located inside the game cabinet. All troubleshooting and maintenance procedures are located in the MAINTENANCE chapter of this manual. The Vectorbeam monitor is unlike the conventional TV monitor. It is a vector system that displays vectors (lines) generated from X-Y coordinates received from the logic board. The horizontal points are X and the vertical Y (width and height respectively). The X and Y logic signals originate from the logic board, discussed later. The +25 volts and 6.3 volts AC and the +25 volt spot kill originate from the low voltage power supply. The +25 volts is a DC voltage rectified and filtered in the supply package. The 6.3 volts AC is used as the heater voltage for the CRT display. On Figure A-1, in the upper-left hand corner, voltages have been regulated by the three terminal regulator devices. For example the +25 volts is regulated by a 7818 and a 7918 respectively down to +18 volts used by the oscillator, Transformer T1 provides the means to supply the CRT grid and anode voltages. The +25 volts is also regulated to +5 volts used for the logic circuitry included in this drawing. The circuit connected to the primary of T1 (a high voltage transformer) form an oscillator which induces the necessary high voltage at the secondary of T1. The frequency is set by the T1 transformer characteristics.

3-2 The output of the TI is then rectified. The highest voltage winding is connected to the tripler M1 which raises the output voltage of this transformer and rectifies it to +18 K volts, for the CRT anode. At pin 6 the negative pulses are rectified and applied to a 1 megohm potentiometer FOCUS control which applies the grid bias at pin 4 of the CRT. The positive pulses are rectified at pin 7 of the T1 transformer as the grid 2 bias for the CRT whereas the CRT at pin 2 is at ground through register R108. The heater pins 1 and 8 of the CRT are connected to ground and pin 1 of the PCB respectively. The +25 volts is also regulated down to +15 volts for the DAC’s by device U10 and U11 (7815 and 7915 respectively). The secondary of T1 (pins 5 and 8) develop the necessary voltage to produce a +90 volts DC rectified by diode CR50 and filtered by capacitor C28. This +90 volts DC is used by the modulating circuit for the CRT display. The lower half of the drawing consists of the spot kill circuit and the intensity modulator circuit. The intensity modulating circuit is comprised of two individual circuits. One input is the high intensity and the other the normal intensity. These two inputs are connected to the high and normal intensity transistor drivers Q20 and Q21 and the hex inverter U6 (7406). Both circuits are identical. For example, in this explanation the high intensity circuit is described: In the high intensity circuit when the input goes high at pin 1 of U6 the output at pin 2 goes low. With this low signal, Q20 is turned off from an on state, and the collector of Q20 goes high. Assume that switching transistor Q24 is turned on. The NORMAL INTENSITY input is always on when the display logic is operating properly. A low input at PCB connector (pin 12) is inverted by hex inverter 7406 which turns on transistor Q22. Device Q22 completes the current path through the intensity control (R91) to ground via resistors R78 and R79 and collector to emitter of Q22. This condition applies a voltage less than +90 volts corresponding to the setting of the intensity control, to the CRT cathode. When a higher intensity is required the HIGH INTENSITY input (pin 14 of the Display PCB) goes low turning on Q20. With Q20 turned on the current path from the +90 volts line in through R91, diode CR39 then finally through the collector to emitter of Q20 to ground. This condition reduces the voltage at the wiper of R91, therefore increasing the intensity of the electron beam. The NORMAL INTENSITY input should always remain low providing some sort of constant electron beam. When the —25 volts is removed, pin 9 of U6 goes high and pin 8 goes low, which immediately turns off Q14 eliminating the chance of a spot. The U6 device is an open collector evice requiring a pull up resistor such as R86 at pin 8. The high side R86 is connected to a voltage source at pin 3 of Molex connector J2. +25 volts unregulated and unfiltered.

Page 17

HIFT

REGISTER

DIGITAL x x

COMPUTER MULTIPLEXER REGISTER

SYSTEM

SEQUENCER x

ADDER Xs

Figure 3-1 DECODER DIGITAL INPUTS SECTION

| COUNTER Y SHIFT | | REGISTER x DEFLECTION DRIVER

ANALOG SECTION CURRENT

* ADDER Y Y MULTIPLEXER REGISTER

General Block Diagram of Speed Freak Game 3-3 Y DEFLECTION DRIVER

Page 18

3-4

ACCUMULATOR To

SELECTOR DISPLAY PROGRAM PROGRAM PROGRAM

SECTION ADDRESS ADDRESS ADDRESS

REGISTER COUNTER SELECTOR

SECONDARY PRIMARY

ACCUMULATOR | ACCUMULATOR

ARITHMETIC LOGIC UNIT SYSTEM

ADD/SUB/AND/OR/LOAD SEQUENCER

  • INPUT INSTRUCTION DATA | SELECTOR REGISTER WORKING | |_| WORKING STORAGE PAGE PROGRAM

DATA AND STORAGE ADDRESS REGISTER MEMORY

MEMORY ADDRESS 12x256 RAM SELECTOR & REGISTER 8x4K ROM

REGISTER

Figure 3-2 Block Diagram of Logic PCB ouTpuT ALTERNATE SELECTOR PROGRAM MEMORY

Page 19

Another spot kill protection circuit (Q21, Q23 and U6) keeps Q14 on when either intensity input is high but when both inputs are low it provides a 2 millisecond turn-on time for Q14. After the 2 millisecond period the Q21 device turns on removing the current path through Q20 and Q22 by turning off Q14. This is accomplished when pins 2 and 4 of U6 are both high which turns on Q23, inverts at pin 10 of U6. Pin 10 of U6 as it switches from a low to a high is initially at ground, then gradually goes positive at C18, until after approximately 2 milliseconds it is positive enough to turn on Q14.

(Refer to Appendix A, Figure A-2) The schematic of Figure A-2 illustrates two identical circuits, one for the Y and the other for the X coordinate. For purposes of this explanation only the upper half will be discussed (the Y coordinant circuit of Figure 3.4). Beginning with the inputs we have 12, 6 inputs to DAC US defining the Y coordinate. These DAC’s generate approximately 4096 (4K) different positions on the screen for the Y coordinate, likewise 4096 for the X coordinate at the lower half of the circuit. Supply voltage to these two DAC’s (U6 and U1) originates from the +15 volt regulators of Figure Al (U10 and U11). The analog output of DAC U5 enters the non-inverting input of amplifier U4 from either the analog Switch 1 or th analog Switch 2. Assume that 4 volts at the analog output (pin 15 of U5) and that analog Switch 2 has been enabled. The 4 volts applied to the input OP-AMP UA also appears across capicitor C35. The output voltage at the circuit of U4 also appears at the wiper of potentiometer R54. The voltage at this wiper is applied to a discrete differential amplifier circuit comprised of device Q16, Q17 and Q18. The +4 volts turns on Q17 which also turns on transistor Q8. The input to this transistor is the output of the differential amplifier of Q17 and Q18. This output is then urrent boosted by the Q10 and Q110 devices for the positive transistion or by the Q6 and Q111 for the negative transitions. Devices Q9 and Q12 are the overload protection. The current then flows through the Y (vertical) deflection coil and back to the inverting input at the base of Q18 in the differential amplifier circuit which nulls out, providing a perfectly balanced current injection circuit. Nothing is displayed on the screen since there is no signal entering the normal or high intensity inputs of the modulator circuitry of Figure A-1. Switch 2 opens leaving the charged capacitor C35 with the initial voltage, which is the initial point of the line segment to be displayed on the CRT after Switch 2 is opened (Switch 1 also remains open). The terminal point of the line segment is entered into the Y register of the logic board and then loaded into the DAC. Assume 5 volts at the output of the DAC, Switch 1 is energized, making contact and appling the 5 volt output from the DAC to the non-inverting input of U4. This new voltage is across the RC network comprised of R58, R59 and C35. The modulating circuits of sheet 1 of 2 turns on the electron beam current to the CRT providing a display from the initial point (voltage across C35) to the terminal point, voltage which has been loaded into the DAC from the Y register. The transition from the initial point to the terminal point appears as a straight line. The rate at which this line segment travels is determined by the RC network at the input of U4. When the register is changed to a new point, Switch 1 opens and Switch 2 closes which places the new value across C35. The initial voltage across C35 is never displayed on the CRT until a signal at the intensity modulator input turns on the electron beam current to the CRT. The lower half of this section for the X coordinate is identical.

THE VECTOR GENERATOR

The vector generator is the digital section of the vector display electronics located on the logic board. As illustrated in Figure 3-3, it shows the working storage register, program memory, arithmetic logic unit (ALU), the primary and secondary accumulators together with the accumulator selector and the system sequencer logic. The remaining logic circuitry which is the X and Y register and the line length timer are primarily used for the display functions and are not shared with the game logic. Figure 3-4 extracts the digital display electronics from Figure 3-3 simplifying its explanation. The line length timer included in Figure 3-4 is divided into the decoderand counter of Figure 3-5. The purpose of the line length timer is to determine the duration of closure to the electron beam switch which allows a vector to be displayed on the CRT. The 12-bit presetable counter comprised of D6 and C6 is initially cleared (CLR) which sets it to zero. It then counts at the rate of the clock (CLK 8). The output of the counter addresses the preset decoder which produces outputs to the counter which are the preset inputs to the counter whenever a load signal goes low. This enable is removed when the line length counter reaches a maximum count.

THE GAME LOGIC

Program Memory

A PROM PCB is temporarily used in place of the standard ROM devices (8, 8 X 1K EPROMS). This PCB is remote from the logic PCB mounted next to the audio PCB. When ROM’s (permanent devices) are developed they are to be installed in their appropriate sockets and remove the PROM PCB.

3-5

Page 20

3-6 Figure 3. 3 Vector Generator Block Diagram QOKREGISTER

PRIMARY

AccUMULAT SCUMULATOR PADPANT x

REGISTER

(54,24 Me)

WORKING

STORAGE

RAM,

AYREGISTER TOTHE MONITOR

DISPLAY BOARD

SECONDARY cnt 4, L10) ACCUMULATOR saesan Le y

(74, RAND DURATION

Page 21

(one-half analog section) Figure 3-4 Simplified Block Diagram of The Display Electronics PCB 3-7

TERMINAL,

COORDINATE

Y“ SWITCH ®

FROM

Y REGISTER

ADJUSTABLE

RC NETWORK MiINPUT

IMPEDANCE

PREAMP

esti ‘\ INITIAL COORDINATE ‘SwiTCH woe POINT

Z 4 IRECTION OF LINE SEGMENT DISPLAY EDWHEN 7 INTENSITY INPUT TURNS ON BEAM CURRENT TOCRT

ae POINT FIGURE SIMPLIFIED OIAGRAM DISPLAY ELECTRONICS PCB CV HAUE OF ANALOG SECTION? CURRENT ‘AoJUST Zs RT VERTICAL DEFLECTION ‘con.

VERTICAL DEFLECTION COIL DRIVER

Page 22

Figure 3-5 Simplified Block Diagram of The System Sequencer Display Section 3-8

Page 23

Figure 3-6 Simplified Block Diagram of The Line Length Timer

PRESET

DECODER

12-BIT

PRESETABLE

COUNTER

LINE DONE

Page 24

The program memory is comprised of 2, 8 X 4K ROMS with two pages of memory in each: 1 even chip, 1 odd chip. The odd chip contains the odd memory and the even chip contains the even memory locations.

The Program Address Counter

(Refer to Appendix A, Figure A-5) The program address counter is comprised of 4-bit binary counters S11, R11 and P11 (74LS163). These counters are presetable by the states of inputs at pin 3, 4, 5 and 6. The Preset inputs originate from register devices P13 and R13 (748377 and 74LS194 dual latch registers). These registers are loaded with the data from the output of the data selector (LO-L11) which originates from either the RAM or the ROM memory (see Figure A-6). When the register is loaded, the output presets the input to the program address. counters. This preset input is loaded when pin 9 of each of the counter devices goes low. This preset input is the initial point from where the counters begin to count. The output of the program address counter, a sequential scheme, addresses the ROM program memory whenever the

program address selector selects bus B. When A is selected

it automatically is tied through the address bus to the ROM Program memory. These counters carry output of each device (S11 the least signigicant device and P11 the most significant). The carry output of S11 triggers the R11 counter. Counter R11 reaches the count of 16 producing high carry output as a dignal t pin 10 to P11. This program address counter is capable of addressing all 4K words of memory in the ROM program memory.

Program Memory Data Bus Multiplexing

(Refer to Appendix A, Figure A-6) The purpose of multiplexing the data bus from the program memory is to make 400NS chips look like 200NS chips. The data selector is comprised of devices T11 and UII which are 2 to 1 data selector devices. When the A input to these two devices are selected it is the data currently processed at the output of the ROM program memory. When B is selected it is a delayed data structure. The outputs of these two data selector devices T11 and U11 form one data bus. The A or the B inputs to these data selectors are selected by the conditions of the outputs RESET, ODD and EVEN from devices U4. In this particular memory therefore the selection between inputs A and B means either the selection of the data from U7 (even) or from R7 (odd).

The Instruction Register

(Refer to Appendix A, Figure A-7) The instruction register (T13) provides all of the instructions in nibbles (4-bits of an 8-bit word) to the system sequencer logic. These instructions are actual instructions

3-10 tequired to systematically set up the game with all the actual event sequences for the board logic.

The Data Register

(Refer to Appendix A, Figure A-7) The data address register (S13) provides the data from the program memory multiplexed to either the RAM memory or RAM address, the computation circuitry or the program address counter through the accumulator D0-D3 is used by the RAM working storage memory and all 8-bits are used by the computation circuitry. The instruction data line [1-17 is multiplexed by device G14 (74LS158).

Working Storage, Address Selector and Register

(Refer to Appendix A, Figure A-8) The working storage address selector and register circuitry, provide the RAM address AO-A7. These address bits locate a particular memory address to either ‘“‘write”” into or ‘‘read’’ out of the RAM. This circuit is comprised of register H12, and single 4-bit register and registers J12 and 112, dual selectable 4-bit registers. Register H12, the page register, matches data bits DO-D3 to the output of H12 (QA-QD). Data bits DO-D3 and the delayed data bits DO-D3 are the upper A, B, C and D inputs to devices J1.2 and I12. The lower A, B, C and D to J12 and I12 are the WO-W7 RAM outputs. These outputs are divided down into nibbles whereas the J12 A, B, C and D lower inputs are W4-W7 and the lower A, B, C and D inputs to R12 of W0-W3. These two quad 4-bit registers as selectable devices, therefore either the RAM output data or data register bits are selectable by the state of the select bit of pin 10, to address a given location in RAM memory. The Data Selector (Refer to Appendix A, Figure A-8) The data selector circuitry is comprised of N11, M11 and L11 (74LS157). The purpose of this circuitry is to select either the data register data bits which are at the inputs of the computational circuitry devices or the RAM output data bits which are the A input to the data selector. The outputs. of L11, M11 and N11 are the register preset inputs for the program address counter.

The Computation Circuitry (Refer to Appendix A, Figure A-9) The computation circuitry is the core of the entire logic PCB. The purpose of this circuitry is to appropriately process all the information in the data instruction to the logic PCB while controlled by the sequencer logic which provides all the timing and control signals to the game logic. The ALU, a major circuitcomponent is comprised of three ALU devices N6, M6 and L6. These ALU’s have the capability of

Page 25

performing 16 arithmetic operations determined by inputs SO, SI, $2 and $3. These inputs re decoded by devices K2, K4 and J8. The operations process either of the A and B ALU inputs. The carry outputs (lo) are tied to look-ahead carry device L4 to be discussed later. After the operation has been performed the outputs from these ALU devices (FO-F11) are then fed to the primary and secondary accumulaters provide two functions: a Y and an X shift register, and arithmetic accumulators. The primary accumulator is comprised of shift registers F4, P4 and M4 (74LS194’s). These shift registers are tied together providing 12 bits of computational capability. This output addresses the ALU, the RAM and the ROM for look-up purposes. All of these outputs while in the display mode supply the X register with X data. The secondary accumulator operates very much like the primary and is comprised of shift registers T4, R4 and N4. These also either address the program memory or provide data bits to the RAM and ALU depending on the state of the accumulator selector. The accumulator selector is comprised of data selector devices R2, N2 and T2 (74L$257). This data selector selects either input A or input B. Input A is the secondary accumulator bits SAO-SA11 and input B which the primary data bits PAO-PAi1. These inputs are selectable by the select input line which originates from the A2 decoder (74LS107). When this bit is low it selects A input, when high it selects B input. Both select lines are commonly tied, therefore providing the identical select signal for N2, R2 or T2. The high speed look-ahead carry generator (74LS182) together with the ALU’s provide a high speed ALU circuit.

The Audio Board (Refer to Appendix A, Figure A-11) The audio PCB generates all of the sounds produced by the game. It also provides the necessary amplification necessary to drive a speaker, mounted at the front of the game cabinet next to the coin mechanism. All control signals enter the audio PCB via connector J4. Pin 2 of J4 is the 78 KHZ square wave generated at the logic PCB. This signal, amplified by op-amp U3 (TLO81), clocks flip-flop USA. The outputs of USA are loaded into USB by the 2MHZ oscillator. This oscillator, comprised of U10 hex inverters, also clocks counter U4. Device U4 counts up from the 9 value (1001) of the preset inputs A, B, C and D. This preset input is loaded into U4 when the Q output of USB places a low at pin 9 of U4. After the preset input to U4 is loaded and the line goes high the counter counts to 15 (1111) where the carry output (pin 15 of U4) goes high and inverted by U10 at pin 9. Pin 8 of U10 then goes low which stops the counter at the count of 15. As long as the counter is counting the carry output at pin 15 of U4 is low maintaining the U5 flips-flops in a reset state. This reset places Q output of USB at a high which removes the low line to.U4 at pin 9. The QA output of U4 produces steady bursts ot three pulses .5 sec wide. The purpose of the circuitry is to triple the crystal controlled frequency from the logic board. This QA output then clocks U18 and divides the input clock frequency by either 32 or 64 at pins 8, 10 and 11 of U18 respectively. These signals are then used by succeeding sound generating circuits. The random noise generator which produces the crash sound is comprised of 8-bit shift register devices U20, U24 and exclusive OR gate U19. The output of this circuit (XPL) is the input to devices U11 (A, B, C, D) gated by the output of the transparent latch device U12. The outputs of this latch are determined by the last four bits of the 16-bit shifter comprised of 8-bit serial in, parallel/out shift registers U13 and U14. The inputs to this shift register are derived from control signals 02 and 03 generated by the logic board. The remaining 12 bits of he shift register are the preset inputs to the modulo N circuit; U15, U9 and U8. These devices are clocked at the frequency of the QA output of U4 when gated by the 01* signal at U6. This frequency is derived by the modulo N toa frequency determined by the twelve preset inputs from the 16-bit shift register. The output of this circuit at pin 15 of UI4 is inverted loading the preset inputs (A, B, C, D) of each counter device. This output is also the trickle count input to the motor noise generator device U7, preset to 2. The horn sound is generated by mixing the outputs of LS107 A and B. The inputs to these latches use signals at a frequency determined by counters U18 and U23. The tire squeal is a result of the output of the voltage controlled oscillator device (555). This device is controlled by the output of counter U24.

Steering Control

(Refer to Appendix A, Figure A-12) The steering control electronics is capable of determining the direction and speed of the steering wheel rotation by the use of a film wheel encoder inprinted with clear and dark areas at its rim. The film wheel rotates with the steering wheel. The rim passes through a pair of electro-optical switch devices U1 and U2 (MCT81) which switch on or off corresponding to the dark and clear areas. The operation of UL and U2 are identical. As the rim of the wheel crosses the path of the light from LED inside U1 or U2, a pulse is generated at the emitter of the internal transistors of U1 and U2. Transistor devices Q1 and Q2 are emitter followers which provide a +5 volt pulse to the 74LS14 Schmidt trigger, switches from the low level pulses generated by the electro-optical switches. The output of the 7A4LS14 (pin 10) sets the steering direction by setting the direction bit at pin 3 of quad latch U4 (74LS175). The output of the 74LS14 (pin 8) is a clock signal that loads the data on inputs (DA-DD) into the U4 latches (QA-QD) simultaneously. The state of the direction bit (high or low) is determined

3-11

Page 26

by the direction of the rim through the electro-optical switch U1 and U2. Initially the steering film is factory adjusted. As the steering wheel is turned to the right the clear area passes through U1 before U2; therefore, pin 4 of U4 goes high. The film continues to turn and the clock input at pin 9 of U4 goes high loading the high data (DA) into QA (pin 3). This high QA output indicates a right turn. When the direction is reversed, the direction bit goes lo

indication a left turn. Latches B, C and D connected together

to form a shift register. This register propagates high levels each time the clock input at U4 (pin 9) goes high. After three clock pulses occur the latches are all loaded high.

3-12 These latches clear when pin 1 of U4 (CLR) goes low (momentarily 38 times per second) clear signal occurs before the latches are loaded. The program will recognize that the wheel was not turned.

PROM Board The PROM board is a temporary board which contains all the program memory for the logic board in programmable read only memory devices. Eventually Vectorbeam will be as thoroughly satisfied with the program as you are and generate a pair of proprietary ROM’s which will fit into their appropriate sockets presently located on the logic board.

Page 27

EST

Page 28

GENERAL

Occasionally an assembly may require repair, replacement or just simple adjustment. In such an event it is necessary for the technician to use this chapter. This chapter provides the technician with step by step instructions for removal or replaceable assemblies or items. It also shows how to adjust.

Display Monitor Adjustment

Procedure This display monitor adjustment procedure adjusts the linearity and convergence of the video display. It also allows the technician to adjust the volume control potentionmeter.

Volume Control Adjustment

  • Adjust the volume control potentiometer (R30) located on the audio PCB assembly, illustrated in Figure 4-7, to the desired volume level while in the test pattern recall mode. Before performing the display monitor adjustment procedure a test pattern must be recalled from the game program memory to the display by following the test pattern recall procedure.

Test Pattern Recall Procedure

  • Remove rear access panel.
  • Plug the game AC plug into AC wall receptacle.
  • With right hand press and hold down the RED START button on the front panel.
  • With the left hand pull out the INTERLOCK SWITCH. The screen should display the test pattern of Figure 4-1. If not try once more from step (c). After recalling the test pattern visually, verify that the display looks close to that of Figure 4-1. If not refer to the following adjustment procedure. Test Pattern Adjustment Procedure (X and Y RC Time Constant Adjustment or the Inner Ends of X and Y Line Segments.)
  • Turn the ‘‘X”’ RC time constant trimpot R61, and adjust the X (horizontal) lines until the two inner ends of each line segment just meet. Turn the ‘‘Y’’ RC time constant trimpot R58, and adjust the Y (vertical) lines until the two inner ends of each line segment just meet. The X and Y lines should meet at the center of the TV monitor screen, if not, check the related display electronics.
  • The ends of the two “‘L” shaped line segments around the center of the display must meet to form the square of Figure 4-1, (b

(c)

4-2 Figure 4-1 Test Pattern Display

Xand ¥ Gain Adjustment

  • Turn the X gain trimpot R60, indicated in Figure 4-7, and adjust the X (horizontal) lines until the two outer ends of each X line segments are 1/4 inch from the edge of the TV monitor screen.
  • Turn the Y gain trimpot R54, indicated in Figure 4-7, adjust the Y (vertical) lines until the outer ends of each Y line segments are 1/4 inch from the edge of the TV monitor screen.
  • If the outer ends of the line segment are not properly adjusting to 1/4 inch from the edge of the screen, center the display. Centering the Display
  • Turn the two CRT magnet rings, located on the neck neck of the CRT as illustrated in Figure 4-2, until the point where the X and the Y lines meet is centered on the monitor screen.

Steering Assembly Adjustment Procedure

The steering assembly is factory adjusted. The following procedure should be performed when the steering PCB or any other item of this assembly is replaced or removed for repair.

  • Remove the control panel. This panel should have already been removed to replace or repair any
Page 29

assembly on the control panel.

  • If the steering wheel film (Figure 4-3) is replaced or removed, loosen the mounting screw at the hub and adjust the position of the wheel by centering the wheel so that the black and clear slits are set.
  • Tighten the mounting screw to the film wheel.
  • If the steering PCB has been replaced or removed loosen the four mounting screws.
  • Adjust the board so that the film wheel fits dead center between the two optical switches as illustrated in Figure 4-3. When satisfied with the setting of step (e) tighten all four screws.

Shifter Assembly Adjustment Procedure The shifter assembly is factory adjusted, but there may be occasion to adjust it for smoother operation. The shifter assembly is comprised of a mechanical shifter rod with a bar magnet attached to its tip (see Figure 4-4), which affects the appropriate reed switch when in close proximity. There are three reed switches, one for each gear except fourth. The switch should make electrical contact when the shifter’s magnetic tip is about 1/4 inch away from the glass reed switch case.

CRT NECK

MONITOR CHASSIS

Figure 4-2 CRT Magnetic Centering Rings Location FILMWHEEL

STEERING SHAFT

a

OPTICAL SWITCHES

STEERING PCB

Figure 4-3 Steering Wheel Film Set-up and Adjustment

  • Remove the control panel.
  • Set the shifter to first gear position.
  • Connect the leads of an ohmeter (set to X1) across the first gear reed switch. See Figure 4-8.
  • Ifthe ohmeter does not read continuity across the read switch, loosen he two mounting screws to the board with the read switch of interest, and move the board unti] the magnet covers maximum area of the reed switch.
  • Place the shifter into second gear. Move the board until the magnet covers maximum
  • Tighten the board screws.
  • Return the shifter to first.
  • Next, bend the board in carefully until the reed switch is about 1/4 inch away from the magnet at the tip of the shifter. The reed switch should be making contact. If not the reed switch is probably defective.
  • Place the shifter into second.
  • Connect the leads of an ohmeter (set at X1) across the second gear reed switch.
  • Continuity should exist. If not return to step (b) until it does. Be sure this reed switch is not defective.
  • The third gear switch may be adjusted as with the first and second.
NOTE

There is no fourth gear read switch.

Page 30

GEAR SHIFTER

MAGNET SWITCHES

Figure 4-4 Shifter Bar Magnet

Control Panel Removal The Speed Freak control panel may have to be removed when the technician is required to maintain the control panel hardware (i.e., steering, wheel assembly, LED pushbutton switch, shifter assembly). The proper procedure for removing the control panel is as follows:

  • Remove the AC power.
  • Remove the rear access panel.
  • Disconnect the cntrol panel Molex connector mounted to a metal bracket.
  • Remove the ground braid connected to the steering assembly. (ce) Remove the four wing nuts from the control panel mounting bolts.
  • Remove the control panel. Refer to Figure 4-5. Plexiglass Shield and Plex Retainer Removal The plexiglass shield and the plex retainer should be removed using the following instructions:
  • Remove the rear access panel.
  • Using either a 7/16"* nut driver or a large blade type screwdriver, back off the two tensioning 1/2 to 5/8

4-4 inch hex slotted head bolts. These bolts are located inside the game cabinet on either side of the face of the CRT, as illustrated in Figure 4-6.

  • Sharply press in on the front of the plexiglass shield.
  • With fingers still pressing in on shield raise the shield up until the bottom edge of shield clears the metal lip.
  • Remove the shield. Plex Retainer Removal
  • Sharply press in the top end of the plex retainer, and raise it up until the bottom edge clears the metal.
  • Remove the plex retainer. Plex Retainer Replacement
  • First slide the bottom edge in over the metal lip then push the plex retainer back into place. Shield Replacement
  • Slide the top edge of the shield into the slot.
  • Push back the shield then slide it down behind the metal lip.
  • Carefully tighten the tensioning bolts.

Vectorbeam video games are relatively new. but designed to endure their rugged environment. Some problems will occur and most are evident as a broken steering wheel or gear

GAME CABINET

CONTROL PANEL

BRACKETS

Figure 4-5 Control Panel Removal

Page 31

shifter or even a burnt out monitor. In other cases the problems must be solved with the experience of qualified TENSION Vectorbeam service technicians. As a result of all their efforts a troubleshooting chart has been devised to aid you with the most likely solutions to your game problems. Refer to Table 4-1. PLEXIGLASS SHIELD

Figure 4-6 Plexiglass Shield and Plex Retainer Removal

4-5

Page 32

Table 4-1 Troubleshooting Chart

PROBLEM PROBABLE SOLUTIONS

a

Circuit Disconnect AC line power to Display PCB Breakers If breakers continue to blow, check for shorted speaker coil Blow Verify proper operation of +15 volt regulators U1 and U16 Check audio drive transistor Q1 and Q2 with ohmeter Check logic PCB for lighted LED, located near power connector LED should not be on Measure voltage at pins 10 and 20 at T13 Voltmeter should read 4.8 VDC

Remove Molex connector U4 and US Check power transistors Q110, Q111, Q210 and Q211 located on heatsinks with ohmeter

Check diodes CR34 and CR35 located on display PCB

Disconnect CRT yoke by removing Molex connector from display PCB Remove CRT socket. Reset breakers Apply AC line power. If unit fails to blow circuit breakers, check transistors Q1, Q3 and Q1 located on horizontal deflection section of display PCB Check diodes CR12 and CR22 located in vertical drive section Check diodes CR1 and CR11 located in horizontal drive section

Check voltage at horizontal and vertical DAC’s at pins 13, 14and 22

Measure outputs of amplifiers U2 and U4 DC offsets Signal should be a +2 volts centered around 0 volts Measure outputs of DAC’s US and U11 Signals should be +4 volts centered around 0 volts

Check vertical size potentiometer R54 for wiper noise by turning R54 Briskly while observing screen. Check R54 pins for weak solder connections.

Display

Jitters

Page 33

Table 4-1 Troubleshooting Chart

PROBLEM PROBABLE SOLUTIONS

Check horizontal size potentiometer R60 for wiper noise by turning ROO briskly while observing screen. Check R60 pins for weak solder connections.

Check DACs U1 and US pins for poor solder connections.

Check Molex connector pins for good connections.

Check analog switch device U3 for loose pins or poor soider connections on socket.

One-inch Check for open power transistors Q110, Q111, Q210 and Horizontal Q211 using an ohmmeter.

Line, Displayed

  • heck . on monitor Check Molex connector to power transistors for open or weak solder connection.

No Display Check the neck of CRT for glowing filament. If filament is not glowing, check brown and black twisted wire pair to CRT plug for 6.3 VAC.

LED on logic PCB should not be on.

Zero scope. Connect scope probe to yellow beam wire at display PCB. Set brightness full clockwise. Data pulses should be 50 volts at an 80-100 WDC base.

If no data present, connect socpe probe to pin 8 of U6. Then dynamically check Q19 for an open collector to emitter junction (41VDC on emitter). Check Q20 and Q22 with ohmeter. Connect scope probe to the cathode of CR32 and check for a full-wave, unregulated spot kill voltage (approximately 25 volts DC). If not check power supply fuse and check Q14 and Q21. Check 18KV at anode cap of CRT. (Use high voltage probe.) If high voltage not present see No High Voltage remedy. Check CRT neck for broken pins. Check the seating of the CRT plug.

Page 34

Table 4-1 Troubleshooting Chart

PROBLEM PROBABLE SOLUTIONS

Narrow Check for open yoke winding Line Displayed Check yoke Molex connector for weak or cracked solder connections

Check Molex connector continuity to Q110, Q111, Q210 and Q211. Check for open power transistors Q110, Q111, Q210 and Q211

Half Display

  • Left Half Missing Check Q1, Q2 and Q210 with ohmmeter
  • Right Half

Missing Check Q5, Q11 and Q211 with Ohmmeter

  • Top Half Missing Check Q6, Q12 and Q111 with ohmmeter
  • Bottom Half Missing Check Q9, Q10 and Q110 with ohmmeter

Brightness Check intensity potentiometer R91 wiper

Potentiometer has no Control Check for open C28 capacitor

Check potentiometer pins for weak solder connections

Circuit breakers Measure DC voltage at pins 10 and 20 of device T13 on the Blow after logic PCB. warm-up Meter should read 4.8 VDC

Check for thermally sensitive 723 regulator devices on the power supply

Check for thermally sensitive devices on the Logic PCB

4-8

Page 35

Table 4-1 Troubleshooting Chart

PROBLEM PROBABLE SOLUTIONS

ee

Remove AC line power to game Remove CRT plug from CRT neck Return AC power Measure pin 3 of CRT plug with oscilloscope. Meter should read 400 VDC.

Measure pin 4 of CRT plug with oscilloscope. Meter should read 200 VDC.

Connect scope probe to yellow beam wire at display PCB. Set intensity control to full clockwise. Data pulses should be 50 volts peak to peak at an 80-100 VDC base.

Measure the AC voltage at pins 1 and 8 of the CRT plug. Meter should read 6.3 VAC.

No Measure DC voltage of regulator U12 High Meter should read +18 VDC Voltage If not present, measure DC voltage at capacitor C25. Meter should read + 25 VDC.

Measure DC voltage of regulator U9 Meter should read -18 VDC.

If not. measure DC voltage at capacitor C17. Voltmeter should read —25 VDC.

Lift winding from pin 3 of high voltage transformer T1. Measure +18 voltage regulators If +18 VDC present check Q31 for short Check capacitors C32 and C34 for shorts Check diodes CR46 and CR47 Check 6KV at black wire Check CRT for bent pins

Check analog switch U3 Inspect yoke connector for poor solder connections Check for open yoke winding Measure DC voltage at capacitor C7 Meter should read +25 VDC Measure DC voltage at capacitor C1 Meter should read -25 VDC

Page 36

Table 4-1 Troubleshooting Chart

PROBLEM PROBABLE SOLUTIONS

Check for thermal sensitivity of devices U2, U3, U4, US and ULL Check operation of DAC U5 Check operation of DAC ULL Check for thermal sensitivity of Q15, Q10, R12 and R39

Check for open’speaker coil Check transistors 2N6292, 2NG6107 in heatsinks with ohmmeter Check OD amp U21 for proper operation Measure DC voltage at output pins of +5 volt regulators U1 and U16 Check for illuminated LED on logic PCB If LED ‘‘on’’ replace device F2 on logic PCB Check open wiper on volume potentiometer R12

Does Not Provide Game time When Coin Inserted Remove AC line power Remove 3-pin Molex connector to coin mechanism

Check switch closure with ohmmeter. (Center pin of connector is common) Verify one pin normally open and the other normally closed Press coin device at coin mechanism. Pins should change state. Normally open to normally closed and vice versa.

Check flip-plop A4 on logic PCB with logic probe on pin 3 of A4. Press coin lever; Pin should change state. With logic probe on pin 6 of A4, press coin lever; pin should change state.

Replace device F2 on logic board.

Coin counter Check transistor 2N3904 and 2N6292 on logic PCB with does not Work ohmmeter

Disconnect coin counter Molex connector Measure DC voltage on red wire Meter should read +25 VDC

Check power connector (J1) to logic PCB

Check electrical connection at pin 3 of J1 (white wire)

4-10

Page 37

Table 4-1 Troubleshooting Chart

PROBLEM PROBABLE SOLUTIONS

No Tire Connect scope probe to pin 3 of oscillator U22 Squeal Verify a 1.8msec FM square wave. Connect scope probe to pin 7 of U22. Scope should display random TTL level pulses. If not see he ‘‘No Crash Sound’” remedy. Check capacitor C23 for an open Connect jumper from pin 2 of U6 to +5 VDC. If tire squeal present, replace device F2 on logic PCB. Remove jumper.

No Horn or Connect a jumper from pin 9 of U2 to GND. If horn Wrong Horn present, replace device F2 logic PCB. Frequency Remove jumper. Connect scope probe to pin 15 of U23. Pulses should be present. Check operation of inverter U19. Connect scope probe to pin 5 of U17. Scope should display a 3.0 msec square-wave. Connect scope probe to pin 3 of U17. Scope should display a 2.2 msec square-wave.

No Crash Connect jumper from pin 3 of U12 to +5 VDC. If crash Sound sound present, replace device F2 on logic PCB

Connect scope probe to pin 14 of U24. Scope should display random digital pulses (white noise). Check latch device U12 Check crash gate device U11

No Replace device F2 on logic PCB Acceleration Check device U7. Observe pulses on pins 12, 13, 13 and 14 Audio Check Modulo-N counter circuit comprised of device U8-U9 and U15

Connect a jumper from pin 5 of U2 to ground. Start light should be on. If on replace F2 on logic PCB. Remove jumpers Check device U2 Replace Q4 Replace start switch

Page 38

Table 4-1

PROBABLE SOLUTIONS ee

Car suddenly Swerves to Either Side

Difficult to Control Car in Higher Gears

4-12 Troubleshooting Chart

Connect jumpers from pin 1 of 74LS178 on the steering PCB to ground Check for logic lows at pins 2. 4, 6 and 12 of 741814 on the steering PCB.

Check harness continuity with ohmmter from pins 2, 4, 6 and 12 of 74LS14 on the steering PCB to respective pins 1, 2, 3. and 4 of device D4 on the logic PCB. Remove connector J3 at the logic PCB Check pins 1, 2, 3 and 4 of D4 for high logic leve. If not replace D4. Reconnect connector J3 Replace resistor pull-up DIP D2. Remove jumpers

Connect scope probe 1 of dual trace scope to pin 4 of device 7ALS175 on steering PCB. Connect scope probe 2 to pin 9 of device 74LS175. Pulses should be displayed on scope as wheel rotates. These two pulse trains should be square waves 90 degrees out of phase with each other. If pulses not present. replace appropriate optical sensor. Using a freon agent (i.e. SPRA-FREEZ or equivalent) spray optical sensor. Replace thermally sensitive sensor. Examine disc capacitors or the underside of steering PCB Assure leads do not touch other pins or paths. Inspect coder disc at end of steering wheel shaft. Assure no dust or nicks in the teeth of coder

Page 39

d4 VERTICAL/HORIZONTAL DEFLECTION COILS J5 VERTICAL R54 DEFLECTION Y DRIVER DEVICES INPUT us Q110,QiN1 ADJUST — Y DAC (SEE NOTE 1)

HORIZONTAL DEFLECTION x DIVICES i Q210,Q211 Tabor PUT

(SEE NOTE 1) Anite

R60

CONSTANT ADJUST R59 YRC TIME us CONSTANT AbJust — ANALOG U4 SWITCH

R91 BRIGHTNESS CONTROL

CONNECTOR

Figure 4-7 Display Monitor PCB Testpoint and Adjustment Layout MI TRIPLER FOCUS CONTROL

Tl HV. TRANSFORMER

4-13

Page 40

C2 PULL-UP DIP un (LV. POWER)

D2 PULL-UP DIP Ql Q2 J3 £3 GAME OPTION DIP. SWITCH

PROM 120-05 XTAL

STORAGE MEMORY (12x256) RAM WORKING

Testpoint and Adjustment Layout x x N = = re} a < ia U TPI

stenerononal Z

J

Figure 4-8 Logic PCB (TO DISPLAY PCB) X ANDY REGISTERS

LOW EVEN

HIGH ODD R7 HIGH EVEN U7 uU13 JUMPER DIP

4-14

Page 41

INPUT FROM LOGIC PCB

VOLUME CONTROL

Figure 4-9 Audio PCB Testpoint and Adjustment Layout

4-15

Page 42

Q2 2N5210

HEX INVERTER PACKAGE COUNTER U4

Figure 4-10 Steering PCB Testpoint and Adjustment Layout

4-16

Page 43

“i O_o ae eeRea ees winked tk ee ee ee es q (Pesesaseeees Sot angeneene A 229293939293

° > a ra I uv g R= as) < Ei § & ° a & a g & fo} oO a = ° x a + y g E} Ay ea}

4-17

Page 44

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 45

Logic PCB Assembly Parts List 38-10001-01 Rev. F

PART NUMBER DESCRIPTION

135-10179-01Test Points
236-10175-01Socket, 16 PIN I.C. DIP
336-10176-01Socket, Amp 16 Jumper
436-10395-01Socket, 24 PIN
537-10178-01Switch, 2 Pole Dip
641-10160-01Con, Molex 09-18-5127, 12 PIN PC, F4
741-10161-01Con, 34 PIN, 3M#3431-2202
841-10162-01Con, 16 PIN, 3M#3408-2202
941-10163-01Con, 26 PIN, 3M#3429-2202
1044-01001-01IC, ROM (1001)
"44-01002-01IC, ROM (1002)
1244-10110-01IC, 74800
1344-10111-01IC, 74802
1444-10112-01IC, 74804
1544-10113-01IC, 74508
1644-10114-01IC, 74810
1744-10115-01IC, 74832
1844-10116-01IC, 748113
1944-10117-01IC, 748158
2044-10118-01IC, 748182
2144-10119-01IC, 745288PROM, DROM, 1
2244-10120-01IC, 745288 PROM, DROM, 2
2344-10120-02IC, 748288PROM, DROM, 3
2444-10120-03IC, 745288PROM, DROM, 4
2544-10120-04IC, 745288PROM, DROM, 5
2644-10120-05IC, 748288 PROM, DROM, 6
2744-10121-01IC, 74LS00
2844-10122-01IC, 74LS02
2944-10123-01IC, 74LS04
3044-10124-01IC, 74LS08
3144-10125-01IC, 74LS10
3244-10126-01IC, 74L$27
3344-10127-01IC, 74/832
3444-10128-01IC, 74LS75
3544-10129-01IC, 74LS85
3644-10130-01IC, 74LS86
3744-10131-01IC, 74L8107
3844-10132-01IC, 74L$151
3944-10133-01IC, 7418157
4044-10134-01IC, 74LS163
4144-10135-01IC, 74L8164
4244-10136-01IC, 74LS194
4344-10137-01IC, 74LS259
4444-10138-01_|IC, 74LS298

5-2

Page 46

Logic PCB Assembly Parts List 38-10001-01 Rev F

PART NUMBER DESCRIPTION 44-10139-01 IC, 74LS377 44-10140-01 IC, 74LS393 44-10141-01 IC, 25LS818

4844-10142-01IC, 2101A-2
4944-10144-01IC, 7425
5044-10150-01IC, 74265
5144-10340-01IC, 74LS257
5253-10054-01Res, CC, %W, 5% 100 OHM
5353-10058-01Res, CC, %W, 5% 330 OHM
5453-10059-01Res, CC, %W, 5% 470 OHM
5553-10062-01Res, CC, “W, 5% 1K
5653-10064-01Res, CC, %W, 5% 2.2K
5753-10066-01Res, CC, 4W, 5% 4.7 K
5853-10070-01Res, CC, %4W, 5% 10 K
5953-10072-01Res, CC, %W, 5% 20 K
6053-10073-01Res, CC, %W, 5% 30 K
6153-10080-01Res, CC, %4W, 5% 560 K
6253-10099-01Res, PACK, IK D-16-15-2-1K
6363-10030-01CAP, TANT, DIP, 25/35V, 3.3MF

63-10031-01 CAP, TANT, DIP, 35V, 33MF 63-10040-01 CAP, DISC, 50V, .0O2MF 63-10042-01 CAP, DISC, 100V, 680PF 65-10026-01 DIODE, SI, SIGNAL 1N914B 65-10177-01 LED, TIL220 66-10011-01 TRANSISTOR, NPN 2N3904 66-10012-01 TRANSISTOR, NPN 2N6292 69-10214-01 CRYSTAL, 20 MHZ 80-01001-01 Logic Board

Page 47

Display PCB Assembly Parts List 38-10007-01 Rev. H

120-10170-01Heatsink 6070B
220-10393-01Heatsink Wakefield 204AB
325-10187-01Nut, Hex #6-32
425-10192-01Nut, Hex #4-40
525-10195-01Screw, Mach. #4-40 x 3/8, PH PH
625-10208-01Lockwasher, STD. #4
725-10209-01Lockwasher, International #6
825-10336-01Screw, Mach. #6-32 x V2 Binding Hd.
936-10174-01Socket, CRT
1036-10175-01Socket, 16 Pin I.C. DIP
140-10173-01Tripler, Varo MH919
1241-10156-01Con, Molex 09-18-5960, 6 Pin PC, F3
1341-10157-01Con, Molex 09-18-5062, 6 Pin PC, F5
1441-10158-01Con, Molex 09-18-5069, 6 Pin PC, F1
1541-10161-01Con, 34 Pin, 3M #3431-2202
1643-10171-01Choke, 100 Microhenry
1743-10172-01Transformer, High Voltage HV18
1844-10143-01IC, 7406
1944-10145-01IC, 7805
2044-10146-01IC, 7815
2144-10147-01IC, 7818
2244-10148-01IC, 7915
2344-10149-01IC, 7918
2444-10152-01IC, TLO81
2544-10154-01IC, DAC80 D/A Converter
2644-10155-01IC, LF13331 Analog Switch
2751-10105-01Pot, 10K A-B #JA1N056S103UA
2851-10106-01Pot, 1 Meg A-B #JA1NO56S105UA
2951-10107-01Trimpot, 100 OHM Bourne 3352P1
3051-10108-01Trimpot, 5 K Bourne 3352P2
3153-10051-01Res, CC, 4W, 5% 15 OHM
3253-10052-01Res, CC, “%W, Zi-CHM
3353-10053-01Res, CC, %W, 5% 47 OHM
3453-10054-01Res, CC, “%W, 5% 100 OHM
3553-10057-01Res, CC, %W, 5% 200 OHM
3653-10058-01Res, CC, “4W, 5% 330 OHM
3753-10059-01Res, CC, %4W, 5% 470 OHM
3853-10061-01Res, CC, %W, 5% 820 OHM
3953-10062-01Res, CC, %4W, 5% 1K
4053-10063-01Res, CC, “%W, 5% 1.8K

41 53-10064-01 42 53-10065-01 Res, CC, “W, 5% 2.2 K Res, CC, “W, 5% 3K 53-10066-01 Res, CC, “W, 5% 4.7K 53-10067-01 Res, CC, “W, 5% 5.6 K 53-10070-01 Res, CC, “W, 5% 10K

5-4

Page 48

Display PCB Assembly Parts List 38-10007-01 Rev H

DESCRIPTION PART NUMBER 53-10076-01 Res, CC, “W, 5% 68 K

4753-10083-01Res, CC, ”W, 5% 1.2 K
4853-10084-01Res, CC, veW, 5% 2.2 K
4953-10085-01Res, CC, ”W, 5% 8.2 K
5053-10086-01Res, CC, ”aW, 5% 10 K
5153-10087-01Res, CC, ”eW, 5% 510 K
5253-10088-01Res, CC, W, 5% 4.7 MEG
5353-10089-01Res, CC, 1W, 5% 2.7 OHM
5453-10091-01Res, CC, 1W, 5% 360 OHM
5553-10092-01Res, CC, 1W, 5% 10 K
5653-10093-01Res, WW, 8W 150 OHM, OHMITE TYPE 200
5753-10095-01Res, WW, 8W 500 OHM, OHMITE TYPE 200
5853-10096-01Res, Metal Film, 1% 1.43 K, RN55D
5953-10097-01Res, Metal Film, 1% 2.1 K, RN55D
6053-10098-01Res, Metal Film, 1% 10 K, RN55D
6153-10101-01Res, CC, %W, 5% 47 OHM
6253-10102-01Res, CC, 2W, 5% 100 OHM
6353-10379-01Res, WW, 2W, 22 OHM DALE RS2B
6463-10029-01CAP, SOV, 50MF, Sprangue TE1307
6563-10033-01CAP, TANT, DIP, 50V, 2.2MF
6663-10034-01CAP, TANT, DIP, 35V, 4.7MF
6763-10041-01CAP, DIST, 100V, .1MF
6863-10043-01CAP, 100V, 5MF

63-10044-01 CAP, ALUM, AXIAL LEAD, 100V, 10MF 63-10045-01 CAP, ALUM, AXIAL LEAD, 150V, 10MF 63-10048-01 CAP, Polycarbonate, 200V .022MF 63-10049-01 CAP, 250V, .O68MF PLESSEY 63-10050-01 CAP, 100V, .1MF PLESSEY 63-10215-01 CAP, DISC, 100V, .0O5MF 63-10380-01 CAP, TABULAR .1MF 600V Sprague 6PS-P10 65-10024-01 Rectifier, FR MR818 65-10025-01 Diode, High Volt, MR250-2 65-10026-01 Diode, SI, SIGNAL 1N914B 65-10027-01 Rectifier, 1 AMP, 1N4003 66-10011-01 Transistor, NPN 2N3904 66-10013-01 Transistor, NPN 2N2102 66-10014-01 Transistor, NPN 2N5210 66-10015-01 Transistor, NPN 2N5320 66-10016-01 Transistor, PNP 2N5322 66-10017-01 Transistor, NPN 2N5550 66-10021-01 Transistor, PNP 2N3906 66-10023-01 Transistor, NPN TIP41C 80-02001-01 Display Board 87-10382-01 Ground Wire Assy - Display Board

5-5

Page 49

WIRE HARNESS. SEE NOTE HEATSINK 20.1029

6:22.N.C.x!; LONG BINDING HEAD. MACHINE SCREW 25-10336 4—PLACES

MICA WASHER 2- PLACES. USE THERMAL GREASE BOTH SIDES,

NOTE 2 “ASSEMBLIES REQUIRED: 38-10006.01 WITH HARNESS 87 10215 01, 38 10008 02 WITH HARNESS HARNESS @7-10315.02

BEND LUG To CLEAR HEATSINK

Figure 5-1 Heat Sink Assembly

5-6

Page 50

40-10268 YOKE, BROY 4746

TIE-WRAP

YELLOW

123 456 41-10228 MOLEX 03-09-1063

35-10225 MALE PIN, MOLEX 02.09.2118 35-10224 FEMALE PIN, MOLEX #02-09-1118

Figure 5-2 Yoke Assembly

Yoke Assembly Parts List 38-10344-01 Rev. A

PART NUMBER DESCRIPTION

35-10224-01 Pin, Female, Molex 02-09-1118 35-10225-01 Pin, Male, Molex 02-09-2118 40-10268-01 Yoke, Broy 746 41-10228-01 Con, Molex 03-09-1063, 6 Pin Recept

5-7

Page 51

Heat Sink Assembly (Front) Parts List 38-10006-01 Rev. B

PART NUMBER DESCRIPTION

09-10337-01 Heatsink Compound, Wakefield #120 20-10229-01 Heatsink (2107) 25-10336-01 Screw, Mach. #6-32 x V2 Binding Hd. 66-10018-01 Transistor, PNP 2N5876 66-10019-01 Trnasistor, NPN 2N5878 87-10315-01 Harness Assembly, Front (for heatsink)

Heat Sink Assembly (Rear) Parts List 38-10006-01 Rev. B

PART NUMBER DESCRIPTION

09-10337-01 Heatsink Compound, Wakefield #120 20-10229-01 Heatsink (2107) 25-10336-01 Screw, Mach. #6-32 x ¥2 Binding Hd. 66-10018-01 Transistor, PNP 2N5876 66-10019-01 Transistor, NPN 2N5878 87-10315-02 Harness Assembly, Rear (for Heatsink)

5-8

Page 52

ITEM PART NUMBER DESCRIPTION

20-10256-01 20-10260-01 20-10261-01 20-10262-01 22-10233-01 22-10251-01 22-10252-01 25-10187-01 25-10203-01 25-10206-01 25-10209-01 25-10263-01 25-10264-01 25-10265-01 25-10341-01 25-10343-01 38-10006-01 38-10006-02 38-10007-01 38-10344-01 90-10266-01 Display Assembly Parts List 38-10003-01

Chassis, Display High Voltage Cage (2105A) Tube Mounting Bracket, L.H. (2169) Tube Mounting Bracket, R.H. (2170) Lable, ‘Do Not Operate Warning’ (2134) Lable, ‘High Voltage’ (2136) Lable, ‘Factory Adjustment Only’ (2137) Nut, Hex #6-32 Screw, Sheet Metal #6 x 3/8 Hex, Type B Screw, Sheet Metal #10 x % Hex, Type A Lockwasher, Internal #6 Washer, Flat #10 Washer, Fender 3/16 Medium Wide, 1 IN. O.D. Spring, Century Spring #171C Washer, Flat #6 3/8” O.D. Waldom #MW-402 Screw, Machine, 6-32 x 3/8, PH PH Heatsink Assembly - Front Heatsink Assembly - Rear Display Board Assembly Yoke Assembly Lube, Cathode Ray 19” 19-VARP4

5-9

Page 53

Audio PCB Assembly Parts List 30-10554-01 Rev. 4

09-10337-01 xxx heat sink compound, Wakefield #120 20-10165-01 HSK heat sink 6072B 35-10498-01 pin, male, PC, Molex 02-09-2134 35-10499-01 pin, female, PC, Molex 02-09-1134 35-10557-01 pin, male, PC, Molex 02-06-8013 .062 35-10558-01 pin, female, PC, Molex 02-06-7103 .062 41-10162-01 con, 16 pin, 3M #3408-2202 41-10228-01 con, Molex 03-09-1063, 6 pin recept 41-10496-01 con, Molex 03-09-2092, 9 pin plug 41-10562-01 con, Molex 03-06-1242, 24 pin recept .062 44-10123-01 IC, 74LS04 44-10124-01 IC, 74L S08 44-10128-01 IC, 74L$75 44-10130-01 IC, 74L S86 44-10131-01 (C, 74L$107 44-10134-01 {C, 74L$163 44-10135-01 1C, 74L $164 44-10140-01 IC, 74L $393 44-10146-01 IC, 7815 44-10148-01 IC, 7915 44-10152-01 IC, TL081 44-10551-01 IC, NE555P 51-10104-01 Pot, 10K Bourne 3355P1 53-10055-01 Res, CC, 1/4W, 5% 150 OHM 53-10058-01 Res, CC, 1/4W, 5% 330 OHM 53-10061-01 Res, CC, 1/4W, 5% 8200HM 53-10062-01 Res, CC, 1/4W, 5% 1K 52-10064-01 Res, CC, 1/4W, 5% 2.2 K 53-10066-01 Res, CC 1/4W, 5% 4.7K 53-10068-01 Res, CC 1/4W, 5% 6.8 K 53-10069-01 Res, CC, 1/4W, 5% 8.2 K 53-10070-01 Res, CC, 1/4W, 5% 10K 53-10071-01 Res, CC, 1/4W, 5% 18K 53-10073-01 Res, CC, 1/4W, 5% 30K 53-10075-01 Res, CC, 1/4W, 5% 47K 53-10076-01 Res, CC, 1/4W, 5% 68K 53-10089-01 Res, CC, 1W, 5% 2.70HM 63-10029-01 Cap, 50V, 50MF SPRAGUE TE1307 63-10034-01 Cap, Tant, Dip, 35V, 4.7MF 63-10037-01 Cap, Disc, 100V .002MF

Page 54

Audio PCB Assembly Parts List 38-10554-01

ITEM | PARTNUMBER DESCRIPTION

63-10038-01 Cap, Disc, 50V, .01MF 63-10040-01 Cap, Disc, 50V, .02MF 63-10041-01 Cap, Disc, 100V, .1IMF 63-10050-01 Cap, 100V, .1MF Plessy 63-10553-01 Cap, 1000V, .001IMF Plessy 65-10026-01 DIODE, SI, Signal 1N914B 66-10011-01 transistor, NPN 2N3904 66-10012-01 transistor, NPN 2N6292 66-10022-01 transistor, PNP 2N6107 80-10529-01 Audio Board, Speed Freak 87-10552-01 asy ribbon cable, 26 pin, 3”

Steering Coder PCB Assembly Parts List 38-10544-01 Rev. 1

PART NUMBER DESCRIPTION

35-10557-0 Pin, male, PC, Molex 02-06-8103 .062 35-10558-01 Pin, female, PC, Molex 37-10543-01 switch optical limit (Monsanto #MC +81) 41-10563-01 Con, Molex 03-06-2092, 9 pin plug .062 44-10541-01 IC 74LS14 44-10542-01 IC 74LS175 53-10055-01 Res, CC, 1/4W, 5% 150 OHM 53-10062-01 Res, CC, 1/4W, 5% 1K 53-10070-01 Res, CC, 1/4W, 5% 10K 53-10075-01 Res, CC, 1/4W, 5% 47 K 63-10034-01 Cap, Tant, dip, 35V, 4.7MF 63-10040-01 Cap, Disc 50V, .02MF 66-10014-01 transistor, NPN 2N5210 80-10545-01 steering coder board

5-11

Page 55

Shift Sensor PCB Assembly parts List 38-10546-01 Rev. L

ITEM | PARTNUMBER DESCRIPTION 35-10557-01 Pin, male, PC, Molex 02-06-8103 .062 35-10558-01 Pin, female, PC, Molex, 02-06-7103 .062 37-10538-01 switch, reed (Hamlin #MDRC4-185) 41-10585-01 Con, Molex 03-06-2055, 5 pin plug .062 80-10547-01 shift sensor board

Control Panel Assembly Parts List 87-10584-01 Rev. 2

ITEM | PARTNUMBER DESCRIPTION 35-10402-01 terminal, solderless for .2 .205X .032 (18-22) WIR 35-10559-01 Pin, male, Molex 02-06-2103 .062, 18-24 35-10560-01 Pin, female, Molex 02-06-1103 .062 18-24 41-10219-01 Con, Molex 03-09-2038, 3 pin plug 41-10561-01 Con, Molex 03-06-2242, 24 pin plug .062 41-10564-01 Con, Molex 03-06-1092, 9 pin recept .062 41-10586-01 Con, Molex 03-06-1056, 5 pin recept .062

Coin Door Assembly Parts List 3810008-01

ITEM PART NUMBER DESCRIPTION

20-10338-01 Fab coin door 25-10227-01 xxx cable tie, nylon 4 In. 25-10270-02 xxx ock, coin door fort #N5078AR403KD 25-10406-01 wsh #10 flat washer plated zinc 25-10407-01 wsh #10 lock washer plated zinc 25-10411-01 nut hex nut 10-24 plated zinc 25-10437-01 xxx tie mount TM 3525 (PANDUIT) 26-10448-01 xxx coin accecptor, #2608-3000-5 with front plate 87-10342-01 asy harness, coin door

5-12

Page 56

Speaker Assembly Parts List 38-01422-01 Rev. A

TEM PART NUMBER DESCRIPTION

20-10293-01 Fab speaker grill 21-10269-02 Fab gasket, speaker 9 1/4'"x 9 1/4" 21-10420-01 Fab gasket speaker 8” (round) x 1/4” 25-10449-01 xxx pop rivet #AD410ABS 25-10450-01 xxx rivet washer flat 4#SBUP 1/8 71-10109-01 Xxx speaker Becker 908A237

Coin Meter Assembly Parts List

ITEM PART NUMBER 38-10008-01

DESCRIPTION

29-10218-01 xxx coin meter E607B-10DC24 35-10224-01 pin pin, female, Molex 02-09-1118 41-10219-01 con con, Molex 03-09-2038, 3 pin plug 65-10027-01 DlO rectifier, 1 amp, 1N4003

Page 57

COIN DOOR

COIN MECHANISM

Figure 5-3 Coin Mechanism Assembly 5-14

Page 58

WIRE WIRE WIRE WIRE WIRE WIRE 41-10228 MOLEX #03-09-1063 TO.3 TRANSISTOR SOCKET, 36-10232 THERMALOY #8113 PF 603 2 PLACES

ALL WIRE 300V 105° C UL LISTED A.W.M.;, STRIP %4" SOCKET END, 'x"" CONNECTOR END.

TIE WRAP

87-10315-01 87-10315-02 392506 50639 2

CONNECTOR, 41-10228

MALE PIN, 35-10225 MOLEX #02-09-2118 D— FEMALE PIN, 35-10224 MOLEX #02.09.1118

642" #18 BLU, 34-10327 612", #18 BLK. 34.10326 642" #18 GRN. 34-10325 612418 RED 34-10324 612"'418 WH. 34-10323 612" #18 ORG. 34-10322

NOTE:
  • HARNESS REQUIRED:
  • 87-10315-09
  • 87-10315-02; IDENTICAL EXCEPT LOCATION OF PINS & WIRES IN CONNECTOR

Figure 5-4 Power Transistors Wiring

Page 59

APPENDIX

A

REFERENCE SCHEMATICS

Page 60

A. Figure A-1 Monitor Display Electronics JOLEX CONNECTOR ‘mIBEON CONNECTOR an CONTROL

Page 61

Figure A-2 Vector Display Electronics

Page 62

Figure A-3 Input/Output Logic

AA

Page 63

Figure A-4 Sequencer Logic

A5

Page 64

Figure A-5 Program Address Counter Computation Logic A-6

Page 65

Figure A-6 Program Memory, Data Bus Multiplexing Instruction and Data Register

Page 66

Figure A-7 Working Storage, Address Selector Address Selector, and Data Selector

A-8

Page 67

Figure A-8 Oscillator/Clock Logic

A-9

Page 68

PARTOF

PARTOF J) MOLEX 03-0215: ro TO! ewsecr RECOMMENDED FUSING: 2A SLO BLO FOR 11SV'154 SLO BLO FOR 220¥

TRANSFORMER SHOWN WIRED FOR

TSVAC OPERATION

Z|

| OnRes

Figure A-9 Power Supply Schematic

A-10

Page 69

A-l1 Figure A-10 Control Harness

STEERING BOARD

41-10564.01 1963285 y Y.

AUDIO BOARD

41-10561.01 wstk. WroRs.

YELLOW

W/RED WSR. BLK. ORG. BRN STRIP vers

wel START SWITCH

ORG. wrsLu. BLK. ORG. wicreY BLK. Worn. GREY BLU. BLK. Wve.

com. +5V Leb Pv com. +5V Pie com. +5 Pie com. PIs NO. NC. com. Pie AKEAXKR ;

COIN SWITCH

a

NOTE:

ALL WIRE #24, 200V 60°C UL& CSA LISTED A.W.M.

Page 70

POWER SUPPLY

40-10223 Mov Ac

41-10228

DISPLAY BOARD

~usteo PAIR #2 BRN. #2 BRN..

SPEAKER

TWISTED PAIR

meBLK, j 2 mew.

10221

AUDIO BOARD

MOLEX

03-09-1093 25,4679)

41-10220 COIN METER #22 RED.

& > 35.10225, MALE PIN, MOLEX 02.92. 35.1026, FEMALE PIN, MOLEX 402-08. 35-10226, 250” FEMALE DISCONNECT, THOMAS & BETTS #A.250 HOLLINGSWORTH 4509600 ALL WIRE 105C 300V, C.5.A.& ULL. LISTED A.W.M. z Ee Mov AC

8 BLK. STED PATI naWH. TWISTED PAIR ‘CABLE TIE 20 PLACES fe. Live

Figure A-11 Power Harness

A-

Page 71

STEERING 4 CONNECTOR a +5 6 @— RESET

9 <@— QD 3—@— ac 2 <@— QB 1<@— QA iy

START SWITCH

SHIFTER

SQU. ARE

Figure A-12 Audio PCB/Control Panel Interconnection Diagram A-13

Page 72

2N5210 2NS210

I

Figure A-13 Steering PCB

A-14

Page 73

Figure A-14 Audio PCB Logic

Page 74

A-16 Figure A-14 Audio PCB Amplifier