CATHODE RAY TOMES

Stun Runner TM-338 1st Printing

S.T.U.N. Runner (rev 6) (Atari Games, 1989) · Technical Manual · 56 pages · 86 sections · original scan

Page 1

TM -238 | 1st printing

ATARI

GAMES

Operator’s Manual

with Illustrated Parts Lists

Page 2

Operator’s Manual

Page 3

Copyright © 1989 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: ‘Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95035

Printed in the U.S.A 9/89

Produced by the Atari Games Technical Publications Department.

Editing: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner S/T-U.N. Runner

Notice Regarding Non-Atari’ Parts

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-Atari parts in the game.

  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: + All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMD ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with alll screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 4

S.T.U.N. Runner

Contents

1 Set Up How to Use This Manual Inspecting the Game ... Control and Switch Locations Setting the Coin and Game Options Game Systems ... Maximizing Earnings Game Play..... e 7 2 Self-Test and Diagnostics

Entering and Exiting the Self-Test .... Automated Self Test Program ROM and RAM Test Microprocessor and Board Tes! Test Menu Screens

Operator Screens.. Coin Options. Game Options. Statistics ... Histograms Error Count... Control Inputs Screen Monitor Test Patterns Special Functions Screen . 2-10 Main Board GSP Tests .... Main Board ROM Checksum .. Main Board ZRAM Test... ADSP Board Tests Audio Board. LEDs on the Main PCB 3 Maintenance and Troubleshooting Maintaining and Inspecting ... Coin Mechanism... Maintaining the Coin Mechanism Interior Components........ Cleaning the Interior Components .. Video Display Adjusting the Video Display Removing the Video Display . Replacing the Video Display .... Flight Control Maintenance Routine Maintenance... Removing the Flight Control Assembly Disassembling the Handle Assembly .. Reassembling the Handle Assembly Disassembling the Flight Control Assembly .. Reassembling the Flight Control Assembly Installing the Harness Assembly 4 Illustrated Parts Lists See the List of Illustrations that follows.

Statistics Sheet v

aS WBE QYW & wy Ga dy

SU Anas

iii

Page 5

Figure 1-1

Figure 2-1 Figure 2-2

Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Figure 2-16 Figure 2-17

Table 1-1

Table 2-1

Table 2-2 Table 2-3 Table 2-4

Table 2-5 S.T.U.N. Runner

Illustrations

Control and Switch Locations... 1-2

Program ROM and RAM Test Screen.. 2-3 Microprocessor and Board Tests Screen... 23 2-4 2-4 Instructions for Test Menu Screen Test Menu Screen... Coin Options Screen Game Options Screen . Statistics Screen, First Histogram Screen .... Second Histogram Screen Third Histogram Screen. Fourth Histogram Screen. Fifth Histogram Screen Sixth Histogram Screen Error Counts Screen. Control Inputs Screen Special Functions Screen. GSP Tests Screen Figure 2-18 Figure 2-19 Figure 2-20

Figure 2-21 Figure 2-22

Figure 3-1 Figure 3-2 Figure 3-3

Figure 4-1 Figure 4-2 Figure 4-3

Figure 4-4 Figure 4-5

Figure 4-6 Figure 4-7

Tables

Game Specifications

Using the Self-Test Screens and Diagnostics Coin Option Settings Game Option Settings .. Summary of All Screens Appearing in the Self-Test ‘When to Use the Special Function. Items .... a0 Table 2-6 Table 2-7

Table 3-1 Table 3-2

Table 3-3 ROM Checksums Screen ... ADSP Board Tests Screen... ADSP ROM Checksums Tests Screer SA Audio Test Screen. DIP Switch and LED Locations on the Main PCB Removing the Video Display Flight Control Assembly Flight Control Removal 2 211

2-13 . 3-4

Cabinet-Mounted Assemblies Flight Control Assembly..... Coin Acceptors, Inc. Coin Door Assembly oe Power Supply Assembly. $.T.U.N. Runner Multisyne (Main) PCB Assembly... ADSP Il PCB Assembly... Stand-Alone Audio II PCB Assembly... 4-21

LED Status Using the DIP Switches...

Maintenance and Inspection Items...... 3-2 Voltage Inputs and Test Points on the Game PCBs... Troubleshooting the Video Di

Page 6

S.T.U.N. Runner

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and, cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game's power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game, Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.
CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT NOTES, CAUTIONS, AND

WARNINGS , cautions, and warnings In Atari publications, not have the following meaning:

NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.
Page 7

S.T.U.N. Runner

Page 8

SET-UP

Chapter 1

How to Use This Manual

This manual is written for operators and service personnel. It provides information for setting up, playing, testing, and maintaining your S.T.U.N. (Spread Tunnel Underground Network) Runner™ game, The manual is divided into the following chapters: ™ Chapter 1 contains set-up and game playing information. ™ Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is important in the S.T.U.N. Runner game, You can troubleshoot the PC boards, main circuits, and controls using the many screens in the self-test. You should regularly test the boards and controls with the self-test to keep your game in peak condition and at top earnings. ™ Chapter 3 contains maintenance, repair, and troubleshooting information for your S$.T.U.N. Runner game. Be sure to perform the preventive maintenance tasks to keep the game in good condition. ™ Chapter 4 contains the illustrated parts lists.

Page 9

Set-Up

Inspecting the Game

WARNING To avoid electrically shocking yourself and damaging the game electronics, do not plug in the game until it has been inspected and set up for your line voltage.

This cabinet should be connected to a grounded threewire outlet only. If you have only two-wire outlets, we recommend that you hire a licensed electrician to install grounded outlets. Players can receive an electrical shock if the cabinet is not properly grounded. Inspect your S.T.U.N. Runner game carefully to ensure that the game is complete and was delivered to you in good condition. Inspect the cabinet as follows: 1, Examine the exterior of the cabinet for dents, chips, or broken parts. 2, Open the service door. Unlock and open the coin doors. Inspect the interior of the cabinet as follows: a. Check that all plug-in connectors on the cabinet harnesses are firmly plugged in. Do not force connectors together. The connectors are keyed so they fit only in the proper orientation. A reversed connector can damage a printed-circuit board (PCB). This will void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets. c. Inspect the power cord for any cuts or dents in > the insulation. d. Inspect the power supply. Make sure that the correct fuses are installed. Check that the harness is plugged in correctly and that the fuse block cover is mounted in place. Check that the green ground wires are connected. e. Inspect other sub-assemblies, such as the video display, controls, printed-circuit boards (PCBs), and speakers. Make sure that they are mounted securely and that the ground wires are connected.

Control and Switch

Locations

Most of the controls are located inside the seat, behind the coin door (see Figure 1-1). The only exception is the power on/off switch.

Power On/Off Switch The power on/off switch is located at the center rear of the cabinet.

1-2 S.T.U.N. Runner

Table 1-1 Game Specifications

Volume Control

Figure 1-1 Control and Switch Locations

Volume Control The volume control is located behind the upper coin door under the seat.

Self-Test Switch The self-test switch is located behind the upper coin

  • door under the seat. See Chapter 2 for a complete description of the self-test.

Coin Counter The coin counter is located behind the lower coin door underneath the coin tray. The coin counter records the number of coins deposited.

Page 10

S-T.U.N. Runner

Setting the Coin and Game Options

The S.T.U.N. Runner coin and game options are set in the self-test. Refer to Chapter 2 for the recommended settings and the procedure for setting the options.

Game Systems

The S.T.U.N. Runner game uses four PCBs to give a realistic look and feel to the driving. These PCBs are the multisync main PCB, the ADSP PCB, the audio PCB, and the video display board. ‘The multisync main PCB, which is the largest, holds the 68010 and the GSP microprocessor systems. The 68010 system contains program RAM and ROM. The GSP (Graphic Systems Processor) microprocessor system controls the video RAMs (VRAMs). The ADSP board is mounted with the multisync main PCB.

Maximizing Earnings

Operator options on this game have been kept very simple. You should thoroughly read Chapter 2, Self- Test for information on the Coin Options, Game Options, Histograms, and Statistics screens so that you can effectively use the available options. Use the Self-Test screens showing Statistics and Histograms to evaluate game data, and the Game Options screen to make adjustments. (Refer also to the Self-Test chapter for more information on setting options.) The key to maximizing earnings is striking a midpoint on game times. Game times must be short enough so that player turnover is high. Conversely, game times must be long enough to give players a good value and

ensure repeat play. (Repeat play i: The S.T.U.N. Runner software gives the operator the flexibility to tune game difficulty and enough statistics to intelligently make adjustments. If collections seem low or are dropping off, check player controls and coin mechanisms for proper operation. If earnings seem low, the game is technically sound, and the average game time per credit is under 150 secconds, choose an easier difficulty level. Set-Up

NOTE The statistics show average time per coin. Depending on the Coin Option settings, the average time per game (or credit) can be computed from the Total Credits, Total Coins, and Average Time/Cain as follows: Avg Time per Credit = Avg Time per Coin X Total Coins + Total Credits.

One of the game option settings (“Continue Advances to Next Level”) can help you maximize earnings. In addition, you can change the price of continuations. After changing game option settings, it is a good idea to reset the game statistics and the histograms. The game statistics can be cleared in the self-test on the sec- ‘ond statistics screen by moving the left joystick and pressing any left player button. The histograms can be cleared by moving the left joystick and pressing any left player button while you are on the histogram screen.

‘Game Play

This section of the manual describes the theme of the S.T.U.N. Runner game and the game play features.

Introduction Take a seat, grasp the controls, and enter the world of the S.T.U.N. (Spread Tunnel Underground Network) Runner. Players travel ahead in time to the 21st century and experience the thrill of racing in a futuristic form of competitive driving. At the control of state-of-the-art technology, players pilot a billion-dollar vehicle capable of attaining speeds of over 900 miles per hour! Players control their vehicles with a return-to-center (RTC) flight controller. Control handles adjust shot elevation and include trigger buttons for firing. The start button is also used as a fire button for “shock waves.”

Play Mode S.T.U.N. Runner is a game of speed. The goal of this game is to travel as fast as possible and complete each race within the allotted time. Numerous enemies prevent the player from achieving this goal. Equipped with powerful lasers, all enemies can be gunned down with the exception of one. The race through the S.T.U.N. Network is made up of many levels. Each level presents a unique challenge to the player. The player's ultimate goal is to guide the vehicle through the network of levels to reach the “Ultimate Challenge.” In this never-ending race, players go

1-3

Page 11

SecUp

as far as their driving skills will take them. If the distance they travel qualifies as one of the top five, their name (18 letters) will be displayed along the road for future players to see (only if they reach this distance). In S.T.U.N. Runner, there is no foot pedal to control speed. Faster speed is achieved by: ™ Correctly driving on the fastest portion of the tunnel ™ Staying off side rails (on flat sections) @@ Avoiding collisions with enemy vehicles m Running over “boosts” for hyperspeed @ Avoiding areas under construction In a turn, the fastest portion of the tunnel is the outer wall. Like a luge or bobsled racer, players use the basic laws of physics to attain the fastest speed. Riding on the inner wall results in a slower speed and hinders a player’s ability to reach a finish line. On flat sections, running into side rails creates a visual and audio chattering resulting in a loss of speed. The first race, a training race, called “Cake Walk,” is intended to teach players how to drive correctly. Red flashing markers in tunnels and flats are called “boosts.” By running over these, the S.T.U.N. Runner gets a boost of hyperspeed. In addition to reaching the finish line faster, a S.T.U.N. Runner in boost is invincible. The vehicle can pass through all enemy vehicles unharmed and cannot be shot. In this mode the player’s vehicle will appear transparent as though it is a skeleton. The underground network has three different tunnel sections. They include wide tunnels, narrow tunnels, and tunnels under construction. Under construction sections contain portions that are unsurfaced. These ar- eas do not provide full power to the vehicle, and slow down the S.T.U.N. Runner. Open areas are called “flats” and are both narrow and wide. Being above the ground, the player is treated to many views of the earth’s surface in the 21st century. On flats, players must avoid driving along the side rails. The friction caused will slow down the S.T.U.N. Runner vehicle. A S.T.U.N. Runner vehicle has six shields for added protection. Colliding with an enemy results in the loss of one shield, At the end of each race, players are awarded bonus points for each shield remaining. A large bonus is awarded if all shields are intact. In the tunnels and flats are ramps. These ramps will catapult S.T.U.N. Runners above the track for a brief distance. Ramp jumping is a often a good method of crossing areas under construction and avoiding collisions with enemies. When players do not reach the finish line of a race within the allotted time, the game would normally end. However, they can be allowed to advance to the next

1-4 ST.ULN. Runner

level on a continuation. The game option setting Continue Advances to Next Level lets you choose whether players advance after 1 or 2 retries, or always, or never. Special Weapon: In selected races, a “shock wave” is located along the way. If the player can pick up the shock wave, the weapon becomes available for use. Also, shock waves can be awarded on some levels if the player hits a predetermined number of stars and completes the level. This information is green in the map at the start of each level. Players activate the shock wave by pressing the start button. This super weapon will destroy all enemies and hazards within view. It is a one-time weapon, but more than one can be stored. The number of shock waves stored is shown as blue and white icons on the screen below the level number display. Bonus Stars: Additional points can be scored along the way by running over “stars.” In the first race, the training race called “Cake Walk,” the stars are red. Players should run over as many stars as possible. In the remainder of the game, all bonus stars are green. Challenge Races: These are bonus races awarded to players for reaching various points in the game. Races 5, 10, and 15 are challenge races. Each presents a unique challenge to the player. @ Boost Challenge 2 m Star Challenge m Kill Challenge In each challenge race, players have one goal. Instructions are displayed prior to the start of each race. The timer clock still operates, but a game will not end because the time expires. This is considered a free bonus for players. Each challenge level has its own high score table. Ultimate Challenge: For those players skillful and patient enough, an “Ultimate Challenge” awaits them at the end. It is an endless race filled with enemies and unexpected surprises. The object is to travel as far as possible within the allotted time. Markers on the road display the names of the five best S.T.U.N, Runners. It is a unique method of identifying the best players of the game. These names are also presented on a separate high score table. Special Contest Feature: Every S.T.U.N. Runner game in the U.S. has a special built-in contest feature. A player can win a free $.T.U.N. Runner T-shirt just for playing the game. All players have to do is reach the checkpoint in the last level, the Ultimate Challenge. For more contest details, see the game.

Page 12

SELF-TEST

&

DIAGNOSTICS

Chapter 2

The S.T.U.N. Runner game is a complex machine. To keep it at peak efficiency and maximum earnings, you should regularly check the controls, RAMs, ROMs, PCBs, and microprocessor systems. You can check all of these when you switch on the self-test. Also in the self-test, you can check the video display and the statistics. If you cannot use the self-test because the screen is dark, you can use a DIP switch on the main PCB to find the source of the problem. If you are having electronic problems, you can check the state of various signals with the LEDs on the main PCB. You should regularly check the following screens and information. We recommend you check these when you first set up the game, each time you collect money, or when the game is not working correctly. @ Use the automated self-test, which begins automatically when you turn on the selftest to test the program RAMs and ROMs, the video RAMs, color RAMs, the ADSP PCB, and the sound PCB. The test takes about five minutes to run.

@ Check the Control Inputs screen, which you choose from the Test Menu screen. This shows the voltage input to the main PCB from the controller potentiometers, trigger switches, and the coin mechanisms, With this information you can easily check how the controls are working. ™ Check the Statistics and Histograms screens which show the statistical information about how your game is played. Table 2-1 shows what tests and screens to use at different times and for different problems.

Page 13

S.T.U.N. Runner

Program ROM and

RAM Test

When you enter self-test, the game tests the program ROM and RAM. The screen in Figure 2-1 shows the results of a program ROM and RAM test.

BAD PROGRAM ROM IS BLANK BOX Y x WV UOT SR

200: = 2 = = 8 210 es 08 8 8 ROMS AT 200R AND 210K CONTAIN THE SELF-TEST PROGRAM

PROGRAM RAM OK

PRESS START TO BYPASS SELF-TEST

Figure 2-1 Program ROM and RAM Test Screen

The top of the screen shows the ROM test result. The numbers on the left and the letters at the top of the screen show the locations of the ROMs on the main PCB. If a white box appears, then the ROM at that location is good. If an empty box appears (as shown at 200U and 210U), then the ROM there is bad. If nothing appears, then nothing was tested there. The RAMs are tested after the ROMs. If the RAMs have no errors, then you see the message Program RAM OK. If the test finds an error, then you see Bad Program RAM At with the bad RAM location listed. This screen disappears after a few seconds and the self-test continues. However, the screen with the results of the complete self-test, shown in Figure 2-2, will show the message Bad Program ROM (or Bad Program RAM) if it found an error in the program ROMs or RAMs.

Microprocessor and

Board Tests

After checking the program RAM and ROM, the automated self-test checks the game's microprocessor and PC boards. It tests the video RAM and color RAM in the GSP microprocessor system, the ADSP board, and the sound board. The test takes four to five minutes. You will see the screen in Figure 2-2 when it finishes. If the system or board is good, OK follows the test name. If it is bad, the word Bad precedes the name of the board or system (except for the ADSP board test, which gives more information). If you have a bad sys- Self-Test

tem or board, then choose Special Functions from the test menu, choose the appropriate system or board tests from the special functions menu, and read the description of the tests in this chapter.

BAD PROGRAM ROM PROGRAM RAM OK GSP VRAM OK--SIMPLE TEST GSP COLOR RAM OK ADSP BOARD OK SAN TEST

PRESS START TO SELECT TEST MENU

Figure 2-2 Microprocessor and Board Tests Screen

A brief description of each microprocessor and board test performed in the self-test is below. PROGRAM ROM: Described above.

PROGRAM RAM: Described above. GSP VRAM: Uses the Simple GSP VRAM Test. (Described in the section Main Board GSP Tests.) GSP COLOR RAM: Uses the GSP Color RAM Test. (Described in the section Main Board GSP Tests.) ADSP Board: Tests the ADSP board memory and the ADSP-2100. Most of the error messages are self-explanatory. (Does Not Respond generally indicates a missing board.) SA II Test: Tests the program ROM and RAM on the sound PC board. If any are bad, the message SA IT Test Error or SA II Timeout Error appears on the screen.

Test Menu Screens

After the microprocessor and board test is finished, or you bypass it, press START to see the test menu screens. Press START once to see the screen with the instructions for moving and choosing in the test menu, shown in Figure 2-3. Press START again to see the test menu. To move down the menu, press the right trigger switch. To move up the menu, press the left trigger switch. You can choose the test menu item with the white letters by pressing START.

2-3

Page 14

Self-Test

USING THE TEST MENU

PRESS RIGHT TRIGGER TO MOVE DOWN OR TO INCREMENT PRESS LEFT TRIGGER TO MOVE UP OR TO DECREMENT PRESS START TO CHOOSE ITEM OR TO RETURN

Figure 2-3 Instructions for Test Menu Screen

The test menu, shown in Figure 2-4, is the most important screen in the self-test. Use this screen to choose the other screens and tests in the self-test. If you choose any item on this test menu, a new screen on that subject appears. Table 2-4 lists all the screens that appear in the self-test.

TEST MENU

OPERATOR SCREENS CONTROL INPUTS MONITOR TEST PATTERNS SPECIAL FUNCTIONS

S.T.U.N. RUNNER VERSION 20.0

COPYRIGHT ATARI GAMES 1989

Figure 2-4 Test Menu Screen

Operator Screens

Choose the operator screens in the test menu by holding START while the words Operator Screens are in white. (For information about moving and choosing in the menu, see the section above.)

If you are in the operator screens and want to go to the attract mode, first press START to go through the remaining operator screens. When you return to the test menu, turn off the self-test switch.

Following are the screens in the operator screens submenu: ST.UN. Runner

@ Coin Options m Game Options m Game Statistics

§ Game Histograms @ Error Count

™ High Score Tables Reset Screen

Coin Options

The coin options appear in the first operator screen (see Figure 2-5). To move and choose in this screen, do the following:

Goin Options [cin Mode Li*s'coins 4 creat Right Mech Multiplier 1 coin counts as { coin Left Mech Multiplier 1 coin counts as 1 coin. Bonus Adder No Bonus Adder

tit LEFTRIGHT Triggers to move UP/DOWN old a Coin Switch and hit Triggers to cycle through choices Hold a Coin Switch and press START to restore original setting ‘Just press START to save this selting and exit

Figure 2-5 Coin Options Screen

™ To move up or down the list, press the right or left triggers. ™ To change a setting, press a trigger and either coin switch.

™ To return to the setting originally on the screen, hold a coin switch and press START at the same

ume.

@ To exit the screen, press the START button.

You can change an option when it is enclosed in a blue box. The default setting of each option is green. The other settings are blue when you select that option. The possible settings are shown in Table 2-2. ‘The coin options are explained below.

@ Coin Mode is the number of coins required for one credit.

™ Right Mech Multiplier is the number of coins each coin counts as in the right coin mechanism. @ Left Mech Multiplier is the number of coins each coin counts as in the left coin mechanism.

m Bonus Adder lets you choose bonus coins, no

bonus, or free play.

Page 15

S.T.U.N. Runner

Table 2-2 Coin Option Settings

Option Available Settings I coin/1 credit 2 coins/1 credit # 3 coins/1 credit 4 coins/1 credit 1 coin counts as 1 coin # 1 coin counts as 4 coins 1 coin counts as 5 coins 1 coin counts as 6 coins” Coin Mode

1 coin counts as 1 coin # ‘coin counts as 2 coins

No bonus adder # 2 coins give 1 extra coin 4 coins give 1 extra coin 4 coins give 2 extra coins 5 coins give 1 extra coin 3 coins give 1 extra coin Free Play : : Left Mech Multiplier

Bonus Adder

© Manufacturer's recommended settings

Game Options

Use this screen to set the game difficulty and various other operator options explained below. The screen is shown in Figure 2-6, and a table of the options is shown in Table 2-3.

To move and choose in this screen, do the following:

™ To move up or down the list, press the right or left trigger. m To change a setting, hold down a coin switch and press either trigger. ™ To return to the setting that was originally on the screen, press a coin switch and the START button at the same time.

™@ To exit the screen, press the START button,

GAME OPTIONS

iGAME DIFFICULTY MEDIUM. 1 TINUE 1S ONE COIN LESS THAN START. OFF ‘SOUNDS IN ATTRACT OFF AUTO RESET HIGH SCORES ON HIGH SCORE NAME CENSOR STRICT T-SHIRT CONTEST DISABLED CONTINUE ADVANCES TO NEXT LEVEL AFTER 1 RETRY

Hit LEFTRIGHT Triggers to move UP/DOWN. Haid 9 Coin Switch and hit Triggers to eyele thraugh choles Hold @ Coin Switch and press START to restore original setting ‘Just press START to save this setting and exit

Figure 2-6 Game Options Screen Self-Test

Table 2-3 Game Option Settings

Option‘Available Settings|
Game Difficulty‘Very EasyMedium Hard

. Easy Hard “Medium Easy Very Hard

Medium # Nasty i

Continue isOne CoinO@On|

Less Than Start (optional) |

Sounds in Attract.=Yes @No|

Auto Reset High Scores. OF one High Score Name Censor Strict Easygoing ¢

‘T-Shirt Contest Disabled Enabled ¢

Continue Advancesto. —_— After. 1 Retry @ Always

Next LevelAfter 2 RetriesNever

Manufacturer's recommended settings |

You can change an option when it is inside a blue box. The default setting of each option is green. The other settings are blue when the option is selected. (The other settings are white when the option is not selected.)

m Game Difficulty sets the game difficulty for the game. The settings are shown in Table 2-3. ™@ Continue is One Coin Less Than Start enables or disables the option that offers players an additional game for one coin. This option only appears if the coin mode option is set to 2, 3 or 4 coins/1 credit. @ Sounds in Attract enables or disables the game sounds during the attract mode demo sequence. ™@ Auto Reset High Scores enables or disables the automatic resetting of all high score tables. When enabled, if 2000 or more games have been played overall and 200 games have been played without any high score entry on any table, all high score tables are reset. ™ High Score Name Censor controls a program to censor names entered on the high score table. The program deletes letters in possibly objectionable words in the high score table. @ T-Shirt Contest enables or disables the T-shirt contest option. You should always have this option disabled after the contest ends on April 1, 1990. ™ Continue Advances to Next Level: When a player fails to complete a level (thus ending the game), he can be allowed to advance to the next level on a continuation.

Statistics

The statistics screen is shown in Figure 2-7. The statistics are collected from the last time the statistics screen was cleared. Write this information on the statistics

Page 16

Self-Test S.T.U.N. Runner

Table 2-4 Summary of All Screens Appearing in the Self-Test

Screen

Automated Self-Test Program RAM and ROM Automated Self-Test Results _ sound PCB tests.

Test Menu Screens : Bes a Instructions for Test Menu Shows information about using the test menu. Test Menu Shows a list of available tests and infec you can choose. Operator Screens ee : Coin Options Sets the coin options. me Game Options Sets the game options, controls the high score ube and steering in ne attract mode.

Statistics Shows game statistics,

Histograms Shows game histograms, and number of sauce by length of play (six total), Error Count Shows the error count from the PC boards. Used by the factory for debugging. High Score Table Shows main high score table and allows the manual resetting of all high score tables. Control Inputs Check this screen regularly to make sure your controls are operating correcily. Monitor Test Patterns Use these screens to check the performance of your video display. Color Bars Shows the video display colors. Monitor Adjust Monitor Brightness Grey Scale B/W Dots B/W Grid Diagonal Lines Full Screen Grey Full Screen White Full Screen Red Full Screen Green. Full Screen Blue Monitor High Voltage Test Scrolling Test Special Functions Main Board GSP Tests VRAM Simple Test VRAM Verify Test VRAM Complete Test Test VRAM for Display Errors Color RAM ‘RAM Shift Register Test

Main Board ROM Checksums.

Main Board ZRAM Tests Used for the monitor setup. Shows the brightness adjustment. 5 Shows the grey scale of the video display. Shows convergence and focus of the video display. Shows convergence and focus of the video display. Shows linearity of the video display. Shows the color purity of the video display. Shows the color purity of the video display. Shows the color purity of the video display. Shows the color purity of the video display. Shows the color purity of the video display. Checks the regulation of the high voltage to the video display. Checks the scrolling mechanism of the GSP microprocessor. Use this screen for tests of the controls, PCBs, and microprocessors. Use this screen if you have a VRAM failure in the automated self-test. Checks for bad VRAMs in the GSP microprocessor system. Tests all the VRAM GSP memory. oe Completely tests all VRAM. Tests for VRAM video. display er errors. Tests the color RAM. Checks the VRAM shift register. Use this test if the program ROMs fail the automated self-test Check the ZRAMs. Use this if all the controls are oper: 1g eputcally or the statistics are not kept correctly. : eo. a

Page 17

S.T.U.N. Runner Self-Test

Table 2-4 Summary of All Screens Appearing in the Self-Test, Continued

ADSP Board Tests :

ADSP RAM -TESTED BY 68010. ADSP PROGRAM MEMORY TEST .2100. ADSP DATA MEMORY TEST .2100. Use this test if the ADSP board fails the automated self-test. ‘The 2100 runs a standard, complete test on its own program memory. ‘The 2100 runs a standard, complete test on its own data memory. 2100 TEST Tests the response of the 2100 integrated circuit on the ADSP PCB. IRQ TEST Tests if the ADSP system can generate IRQs. ROM CHECKSUMS Tests the graphics ROMs on the ADSP PCB. ADSP SPECIAL FUNCTIONS Performs hardware Glagnoss a and orloscone test oops for use by a repair technician. Audio Board Tests ‘Use these tests if the SA Il audio. board fails the ae self-test. “Sound Board Self-Test Tests the sound PCB and reports the result Play Sounds Choose and hear game sounds.

STATISTICS

VERSION 20.0 FRI SEPT 8 09:

LEFT COINS: 27 RIGHT COINS: AUX COINS: IDLE MINS: ACTIVE MINS:

HOLD A COIN SWITCH AND PRESS START TO CLEAR STATISTICS

JUST PRESS START FOR HISTOGRAMS.

TOTAL CREDITS: 49 TOTAL COINS: 61 AVG TIME/COIN: 114 SEC

Figure 2-7 Statistics Screen

sheet in the back of this manual to help you maximize your profit. To move to the next screen, just press START. To clear the statistics, hold a coin switch and press START at the same time.

The statistics that the game collects are explained below.

& Left Coins shows the number of coins counted in the left coin mechanism. ™ Right Coins shows the number of coins counted in the right coin mechanism. @ Aux Coins is not used.

@ Idle Mins shows the number of minutes the game has been idle.

Active Mins shows the number of minutes the game has been played. ™ Total Credits is calculated by multiplying the coins by the credit setting you chose in Coin Mode.

Histograms

Read the histogram screen frequently and record the numbers on the statistics sheet in the back of the manual. You should read and reset the screen frequently because if more than 256 games occur in any one time category, then the counts of all the time categories are divided by two, so the information remains proportionally accurate, but not numerically accurate. If you read the screen infrequently, it is likely that you will not have a true numerical count of the number of sessions because of the way the histogram numbers are handled. The histograms screens appear in Figures 2-8 to 2-13. To clear the histograms, hold a coin switch and press START at the same time. To move to the next screen, press START.

2-7

Page 18

Self-Test S.T.UN. Runner

Histogram 4 Level Continued From Histogram 1 New Game Times 0-99 123 100-119 102 120-439 88 140-159 78 160-179 53 180-399 45 200-219 34 220-238 27 240-259 14 260-279 280-299 300-319 320-339 340.359 a 3 6 400-419 = 420-439 440-459 460 -UP Just press START dust press START for next level for next level

Figure 2-8 First Histogram Screen

Histogram 5 Histogram 2 Scores Continuation Game Times 0.99 129 400-119 120-139 140-159 460-179 380-199 200-219 220-239 240-259 260.279 280-299 300-319 320-339 340.359 360.379 380-399 400-419 420-438. 440-459 460 -UP oO. 4K

  • 9K 40-14K 415-19K 20 - 24K 25 - 29K 90 - 34K 35 - 39K 40 - 44K 45 - 49K
  • 54K 55 - 59K 60 - 63K 65 - 69K
  • 74K 75-79K 6 80 - 84K = 85.- 89K 90..94K ‘95K & UP

dust press START for next level ‘Just press START. for next level

Figure 2-9 Second Histogram Screen Figure 2-12 Fifth Histogram Screen

Histogram 3 Hist Level Died At istogram & Excess Time (1/10th sec)

1o mp bee |

20 & UP Hold a Coin Switch and press START to clear histogram Just press START dust press START for next level for next levet

Figure 2-10 Third Histogram Screen Figure 2-13 Sixth Histogram Screen

Page 19

STUN. Runner

Error Count

This screen, shown in Figure 2-14, shows the error counts on the PC boards. If you call Atari Game Customer Service, the numbers on this screen may help Customer Service personnel troubleshoot your problem.

ERROR COUNTS

WATCH DOG RESET BUSS ERROR ADDRESS ERROR ILLEGAL INST ERROR DIVIDE BY ZERO ERR HK INST ERROR TRAP ERROR PRIV VIOL ERROR GSP HANDSHAKE ERROR BAD POLY BUFF ERROR MSP TIME OUT ERROR ADSP TIME OUT ERROR GSP TIME OUT ERROR GENERIC ERROR NMLERROR SPUR EXPTN ERROR iLLEGAL ERROR CODE eoeaoogaceooeNOON

Hold a Coin Switch and press START to clear error counts dust press START for next menu

Figure 2-14 Error Counts Screen

Control Inputs Screen

Check this screen as part of your regular maintenance to be sure your controls are operating correctly. The Control Inputs screen is shown in Figure 2-15.

CONTROL INPUTS

CONTROL LEFT/RIGHT

CONTROL UP/DOWN

LCOIN RCOIN. LEFT TRIGGER RIGHT TRIGGER

Figure 2-15 Control Inputs Screen

If you have a problem with a control, check Chapter 3 for troubleshooting and repair information about the control. Self-Test

When the line is shortest, the input is 0 Volts. When it is longest, the input is 5 Volts. If the line length for the control does not change, you have a problem with the control. See Chapter 3.

Monitor Test Patterns

Use this item to see the thirteen screens for checking the video display, the color RAMs, the GSP, which controls the video RAMs (VRAMs), and the video output. To move through the screens, press the coin switches. ™ Color Bars screen shows these colors from left to right: white, yellow, light blue, green, purple, red, blue, and grey. If the colors are incorrect, see your video display manual for adjustment procedures. ™ Monitor Adjust is used to set up the monitor. ™ Monitor Brightness checks the adjustment of the video display brightness. ™ Grey Scale screen shows a white line on the left, and a grey scale showing black on the left. ™ B/W Dots screen can be used to check convergence and focus. @ B/W Grid scteen, shows a black background and a white grid pattern to check convergence. The grid lines should be straight within 3.0 mm. If you need to adjust the convergence, see the video display manual included with the game.

™ Diagonal Lines screen can be used to check video display linearity. @ Full Screen colors test the color purity of the color RAMs and the display. The test displays a grey, white, red, green, and then blue screen. Each screen should be a rectangle of color, with no curving at the corners and no lines in the raster. If it is not, see your video display manual included with the game for adjustment procedures. ™ Monitor High Voltage Test screens switch between a white screen and a grey screen. If the high voltage to the display is regulated properly, the sizes of the white and grey screens will differ by about 3/4 inch. § Scrolling Test screen checks the scrolling mechanism in the GSP.

2-9

Page 20

Self-Test

Special Functions Screens

Use the items on this screen, shown in Figure 2-16, if a system or board failed the program RAM and ROM test; if a board and microprocessor failed the automated self-test; if you have problems with the flight control or if the statistics are erratic. A short summary of when to use these items is provided in Table 2-5.

SPECIAL FUNCTIONS

Exit MAIN BOARD GSP TESTS RESERVED MAIN BOARD ROM CHECKSUMS MAIN BOARD ZRAM TEST ADSP BOARD TESTS SOUND BOARD TESTS

Figure 2-16 Special Functions Screen

The Special Functions items are explained below.

& Exit returns you to the test menu. ™ Main Board GSP Tests should be used if you get the. message Bad GSP VRAM or Bad GSP Color RAM in the automated self-test. This screen has six tests you can use.

@ Main Board ROM Checksums should be used if you get the message Bad Program ROM in the automated self-test. This tests the program ROMs individually and shows the results on the screen. § Main Board ZRAM Test should be used if your conols settings are changing or erratic. Also use these tests if you suspect the game is not keeping the Statistics correctly. @ ADSP Board Tests should be used if you get any message other than ADSP Board OK for the ADSP board test in the automated self-test. This screen has five tests and an ADSP ROM checksum test. It also has a special functions menu for factory use only. ™ Sound Board Tests should be used if you get the message SAII Test Error in the automated self-test.

2-10 S.T.UNN. Runner

Main Board GSP Tests

If the automated self-test reports bad VRAMs, choose Main Board GSP Tests and the screen in Figure 2-17 appears.

EXIT VRAM SIMPLE TEST: 18 SECONDS

VRAM COMPLETE TEST: 11 MINUTES TEST VRAM FOR DISPLAY ERRORS COLOR RAM VRAM SHIFT REGISTER TEST

Figure 2-17 GSP Tests Screen

First run the VRAM simple test. It gives the location of the bad VRAMs. If the VRAMs pass this test, but you think the game has a bad VRAM, run the VRAM verify test. @ VRAM Simple Test is the same test that is run in the automated self-test. It is run by the 68010 through the GSP interface and detects open or shorted address or data lines or missing parts. The results are displayed on-screen with a picture showing the RAM section of the main PC board. The good parts are shown in green and the bad parts are shown in red, If an entire section appears in red, the problem may be with a buffer associated with that section. The test takes about 15 seconds.

m@ VRAM Verify Test is a complete memory test run by the GSP. The results are reported on the screen as in the simple test. The test takes about 90 seconds to run, Since the verify test is run by the GSP program in the VRAMs, a single bad VRAM can cause the GSP program to crash. When this happens, the 68010 microprocessor reports that all the VRAMs are bad, although probably only one VRAM is bad. You must run the VRAM complete test (described below) to find out which VRAM is bad. If the VRAM verify test fails, but the VRAM simple test shows the VRAMs are good, you should run the VRAM complete test. If the verify test runs and reports that the VRAMs are good, then the VRAMs should be good.

Page 21

S.T.U.N, Runner Self-Test

Table 2-5 When to Use the Special Function Items

__Item. = _WhentoUse re Main Board GSP Tests

If you see the message Bad GSP VRAM or Bad GSP Color RAM in the automated

self-test. If you see the message Bad Program ROM in the automated self-test. If your control settings are changing even though you have used the Set Controls screen or if the statistics are not being kept correctly. If you see any message other than ADSP Board OK for the ADSP PC board test in the automated self-test. Main Board ROM Checksums

Main Board ZRAM Tests

ADSP Board Tests

Sound Board Tests If you see the message SAH Test Error in the automated self-test.

@ VRAM Complete Test is a complete memory test run by the 68010 through the GSP interface. Because the 68010 runs the test, a single bad VRAM does not cause the test to report that all the VRAMs are bad (as it does the verify test). Any VRAMs that are bad are shown on the screen at the end of the test. This test takes at least eleven minutes to run.

@ Test VRAM for Display Errors checks for video display problems. ™ Color RAM is the same test that is performed in the automated self-test. It tests the color RAM and reports the results.

& VRAM Shift Register Test checks the shift register part of the video RAMs.

Main Board ROM Checksums

This screen checks the main PC board program ROMs for errors. Use this test if you have a bad program ROM message in the automated self-test or you suspect program ROM failure. To exit this screen, press START.

When the checksum test is complete, the screen shows the list of ROM locations, the checksum, and what the checksum is expected to be (see Figure 2-18). Only the last two digits of the checksum are important.

Main Board ZRAM Test

This test checks the non-volatile RAM where the game statistics and control set-up values are kept. Check the ZRAMSs if you think the statistics are incorrect.

If the game loses power or is reset while it is in this test, then the statistics will be lost. The statistics cannot be restored. PROGRAM ROM CHECKSUMS

LOC. CHECKSUM EXPECT LOC. CHECKSUM EXPECT

+02xxo2201xxot
7204xx048103xx03
1306xx06B705XxKO5
3308xxos2E07x07
AFIOx10709x09
Srix2FEot
00020K,‘90000K
9000300K0000XXX

XX = DO NOT CARE

Figure 2-18 ROM Checksums Screen

Use this item if the ADSP PC board fails the microprocessor and board tests performed in the automated self-test.

When you select ADSP Board Tests from the test menu, the screen in Figure 2-19 appears. The items on the screen are explained below.

ADSP BOARD TESTS EXIT ADSP RAM - TESTED BY 68010.

ADSP PROGRAM MEMORY TEST .2100. ADSP DATA MEMORY TEST .2100. 2100 TEST IRQ TEST ROM CHECKSUMS ADSP SPECIAL FUNCTIONS

Figure 2-19 ADSP Board Tests Screen

2-11

Page 22

Self-Test

w Exit returns to the test menu. @ ADSP RAM Tested by 68010 tests the memory on the ADSP PC board. The 68010 on the main PCB tests the ADSP program memory, the ADSP data memory, and both ADSP output buffers. The memory tests are the standard, complete tests but are run at the 68010's bus speed, which is slower than that of the 2100. & ADSP Program Memory Test .2100. is a standard, complete memory test run by the 2100 on its own program memory. Since the test program must reside in memory, a bad program RAM may prevent the test from running. However, because the program memory is divided into two banks, the test is divided into two parts. The program to test the upper bank is run from the lower bank; the program to test the lower bank is run from the upper bank. Unfortunately, the 2100 always starts operating from a specific address in the lower bank. Therefore, the lower bank must be operating to the extent that it can execute a JUMP instruction to the upper bank.

These tests operate solely with program memory; they do not require that any data memory be operational. ™@ ADSP Data Memory Test is a standard, complete test run by the 2100. It operates solely with program memory and does not require that any data memory be functional. & 2100 Test checks the response of the 2100 integrated circuit on the ADSP PC board by copying data from one location to another using a 2100 program. IRQ Test checks if the ADSP can generate interrupts for the 68010. m@ ROM Checksums tests the graphic ROMs on the ADSP PC board. When the checksum test is complete, a hexadecimal number follows each ROM as shown in Figure 2-20. The first two digits in each hexadecimal number can be any number, but the last two digits must be the ones shown in Figure 2-20. If the last two numbers are different, then the ROM is bad or it is not on the board.

@ ASDP Special Functions performs hardware diagnosis for use by a repair technician.

Audio Board

Use these tests if the SA II Audio board failed the microprocessor and board tests in the automated self-test.

If the SA II Audio board failed the test, select this item

from the test menu and a screen such as the one in

Figure 2-21 appears. The tests are explained below. S.T.UN. Runner

ADSP ROM CHECKSUMS

CHKSUM EXPECT TFIZ XxX47 XX18 XX19 xX20 Loc. ASDP 9K: ASDP 9/10K: 5518 ASDP 10K: 8919 ASDP 9H: 0E20 ASDP 9/10H: DF21 XX21 ASDP 10H: 3022 XX22 XX = DO NOT CARE

Figure 2-20 ADSP ROM Checksums Tests Screen

™@ Exit returns to the test menu. SA Self-Test checks the sound program ROM and RAM. m@ Play Sounds takes you to the Requesting Sound Screen. Follow the instructions on the screen to hear the game sounds.

SA AUDIO TEST

SA AUDIO TEST OK

Figure 2-21 SA Audio Test Screen

LEDs on the Main

PCB

The LEDs (light-emitting diodes) on the main PCB show you the status of signals on the main PCB. Using the LEDs, you can check signals from various circuits

  • going to the 68010 processor. The state of the signals is shown by the LEDs which flash or stay lit. Figure 2-22 shows the location of the LEDs on the main PCB. Table 2-6 shows the possible status of the LEDs, with an explanation of what they indicate.
Page 23

S.T.U.N, Runner Self-Test

Table 2-6 LED Status

Status — LED Indicates Run LED State of 68010 HALT signal.

DTACK LED. State of 68010 DTACK (data acknowledge) signal.

Clock LED State of the 68010 processor clock signal.

IRQS LED State of all 68010 interrupts. “Onwhen 68010 is running.

*and clock must be running.)

On ‘when the 68010 processor is Sanne and the timing cir

© quit is probably operating © Offwhen 68010 processor is not running. Flashing at 2 Hz if the 68010 cannot run. (The watch-dog

the Run LED Is ote ae mode.)

Flashes at 2 Hz when the 68010 processor cannot run. (The watchdog and processor clock must be running.) (The DTACK LED is on in game mode.)

On-when the game board is on. Offif the processor clock signal is stuck high or low. On in the game mode. Offi hardware diagnostic mode and the early part of selftest. Offif no interrupts are occurring or any imeerrupt signal is stuck low.

DIP Switches

If you try to enter the self-test, but nothing appears on the screen, use the DIP switch tests. Use the information from these diagnostic tests to help you find the problem. Before you begin with these following tests, be sure that the problem is in the game hardware, not in the video display. If you have a completely dark screen, check the following: @ Do you have power to the video display? Are the video display’s filaments lit? @ Do you have high voltage to the video display? If the answer to any of these questions is no, then you have a problem in the video display. Check the video display service manual included with your game for the suggested procedure. If you are sure that the problem is not with the video display, then ty the DIP switch diagnostics shown in Table 2-7, at the end of this chapter. These tests isolate various ICs and systems for troubleshooting. The results of the tests are indicated by the main PC board LEDs or on the video display screen. To set the DIP switches for the tests:

  • Put a jumper across the DIAGN test points, shown. in Figure 2-22.
  • Select the diagnostic test you want to use with the DIP switch settings.
  • Turn on the self-test switch. 4, Put a jumper momentarily across the RESET test points, shown in Figure 2-22. To change to another DIP switch test:
  • Change the DIP switch settings.
  • Put a jumper momentarily across the RESET test points. To end the DIP switch testing: 1, Take the jumper off the DIAGN test points.
  • Put a jumper momentarily across the RESET test points. The DIP switch settings are on in the top position when the main PCB board is in the game.

Figure 2-22 DIP Switch and LED Locations on the Main PCB

2-13

Page 24

Self-Test S.T.U.N, Runner

Table 2-7 Using the DIP Switches

Type of Test

Uncleared Watchdog

Cleared Watchdog

Test LEDs

Test Program ROM 0

Test Menu RAM 0.

GSP Communications

Red Screen

Green Screen

Blue Screen

GSP Memory Fill GSP VRAM Verify

ROM Test Loop RAM Test Loop

BERR

| 1-On; O- Off; X=Doesn't Matter. Waundos. 7

The results are displayed on the screen,

The teats are displayed on the Screen

_ to perform this test.

Puts the 68010 in a loop. Does not clear the watchdog seubeee The run LED, DTACK LED, and IRQs LED flash at 2 Hz and the cl

program RAM does not need to work. If the watchdog is working, the

is on. : Puts the 68010 in a loop. Clears the watchdog counter. The program

RAM does not need to work. If the watchdog is working, the run TED, test LEDs are workings they flash at 2 Hz

clock LED, DTACK LED and IRQS LED are on. test LEDs are workings they flash at 2 Hz.

Tests ROM 0 H and 0 L, which hold the test program. (This test takes good. If ROM 0 L is bad, LED 1 does not flash. ROMO HE bad

about 5 seconds.) LED 1 and LED 2 flash together if both ROMs are

LED 2 does not flash. eh tae Tests RAM 0 H and 0 L, which run the test menu, “Chis test takes about 5 seconds.) LED 1 and LED 2 flash together if both RAMs are

good. If RAM 0 L is bad, LED 1 Soe! at Hah If RAM 0 His bad Tests if the 68010 can communicate with the GSP, “which produces Produces a red screen from the color RAM, regardless of GSP: VRAM xx Produces a green screen from the color RAM, regardless of ose VRAM zx o1

LED 2 does not flash. GSP Tests

the video. If the GSP responds, the LEDs flash together. If the a f does not respond, LED 1 and 2 flash alesnaely, ex 04

input. Use this to heck the red video outputs. _

input, Use this to check the green video outputs. Produces a blue screen from the color RAM, regardless of GSP VRAM x Xo1 input, Use this to check the blue video outputs, :

Performs the GSP VRAM ven tes. (Thus test is al

ROM and RAM Tests

Bus Error Test ‘The DTACK timer times out and generates a bus error The results are displayed on the screen, The DUART

Page 25

MAINTENANCE

&

TROUBLESHOOTING

Chapter 3

This chapter includes maintenance, repair, and troubleshooting information for your S.T.UN. Runner game. In the game, the hardware and software are closely related. If you are having problems with a mechanical assembly, always keep in mind that your electrical connections may not be good or you may have an electronic problem. To determine what kind of problem you have, always use the self-test screens as recommended for each part.

The first part of the chapter includes a schedule for | game maintenance and inspec- 4 tion, a table with general troubleshooting information, and a table of the voltage levels and test points on the PCBs. The rest of the chapter is arranged in alphabetical order by the name of the part or control. Under each part are maintenance procedures, troubleshooting tables and flowcharts, and repair procedures for the part. If a part is mentioned, but not illustrated, refer to Chapter 4, Mlustrated Parts Lists, for information.

Page 26

Maintenance and Troubleshooting S.T.U.N. Runner

Table 3-1 Maintenance and Inspection Items Part ‘When to Check _ ‘All Controls © Every month Every 6 months ‘Every 3 months s

Coin Mechanism

Interior Components

Table 3-2 Voltage Inputs and Test Points on the Game PCBs

PCB Voltage Test Points Source and Purpose

Main +5401 VDC -+5V2 Power Supply

ADSP +5 VDC a

+5V1 or +5V2. ~ Regulated and supplied fro

Maintaining and Inspecting

Preventive maintenance includes inspecting, cleaning, lubricating, and tightening hardware. Perform the preventive maintenance regularly so you can keep the game in top condition, avoid problems, and maximize your earnings. Preventive maintenance tasks and intervals are shown in Table 3-1. For the best performance from your S.T.U.N. Runner game, maintain your game according to the times shown in Table 3-1. Instructions for performing these tasks is explained in the section about that control in this chapter. You may want to perform these tasks more often if the game is heavily used. Table 3-2 shows the correct voltage levels to various PC boards and the test points for those voltage levels. Low voltages to PC boards may cause problems with the controls, with the video display, or in game play.

The coin mechanism should be cleaned every three months,

Maintaining the Coin

Mechanism

  • Turn off the power to the game. Open the upper coin door,
  • Open the gate on the door covering the magnet. Use the blade of a screwdriver to scrape away any metal filings collected on the magnet.
  • For a thorough cleaning, wash the coin mechanism in hot soapy water. Use a toothbrush to remove any stubborn build-up of residue in the coin path. 4, Dry the coin mechanism with compressed air.
  • If you do not want to use water, brush the loose dust off with a soft brush and scrub the residue in the coin path with a toothbrush. Blow all the loose dust and dirt out with compressed air.

3-2

NOTE Never lubricate the coin mechanism with oil or grease.

Interior Components All the components in the interior of the game should be cleaned every three months. This includes the PCBs, the power supply and the video display.

Cleaning the Interior Components Perform the following procedure to clean the components inside the cabinet.

  • Open the rear service and top service doors.
WARNING Turn off the AC power, but do not unplug the power cord before cleaning inside the cabinet. The power cord provides a ground path for static voltage that can be present on the cleaning tools.
  • Use a vacuum cleaner with a soft long-bristled brush attachment or use a soft-bristled paint brush to remove loose dirt and dust from the inside of the cabinet. Be sure to clean the power supply, PCB assemblies, and video display thoroughly.
CAUTION Be extremely careful when cleaning the electrical components inside the cabinet. Do not touch the electrical components with any solid object other than the soft bristles of the vacuum attachment or paint brush.
Page 27

S.T.U.N. Runner

Video Display

If you have problems with the video display, check Table 3-3, Troubleshooting the Video Display, before you remove the display.

Adjusting the Video Display’

To make adjustments to the video display, open the service door on the cabinet.

Removing the Video Display

Perform the following procedure to remove the video display. (See Figure 3-1.)

  • Turn the game power off and wait two minutes. Leave the power cord plugged in.
  • While you wait, unlock the top service door on the top of the cabinet.
  • Remove the six screws that attach the shield frame and remove the frame, shield, and bezel.
WARNING High Voltage The video display contains lethal high voltages. To avoid injury, do not service this display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation The video display is designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped. The shattered glass from the tube may cause injury up to six feet away. Use care when handling the display. Maintenance and Troubleshooting

. Remove the four nuts and washers that service the monitor. . Discharge the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when power is removed. However, to make certain, always discharge the display as follows: a.Attach one end of a solid 18-gauge wire to a well-insulated screwdriver or wooden handle. b.Attach the other end of the wire to an earth ground. c. Quickly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. d. Wait two minutes and repeat part c. . Disconnect the harness connectors from the video display. . Pull the video display assembly out of the cabinet. Be extremely careful.

WARNING When you take the video display out of the cabinet, do not drop it! The display is heavy. Be careful! Wear gloves to protect your hands from the sheet-metal edges.

Mu

Problem Table 3-3 Troubleshooting the Video Display Solution. ‘Any problem.

Convergence, purity, or color problems. "Determine if the problem is with the display or the game hardware by performing the self-test. If you cannot perform the self-test, use the DIP switch diagnostics to narrow down the source of the problem. Check the voltage level to the video display.

th isplay settings with the Mc

B.

itor Test screens in the self-test.

3-3

Page 28

Maintenance and Troubleshooting S.T.UN. Runner

Replacing the Video Display ; When you replace the cathode-ray tube

NOTE

Perform the following Procedure to replace the video and yoke together, adjust the brightness, display in the cabinet. (See Figure 3-1.) size, and centering as described in the

  • Carefully lift the video display into the cabinet. video display service manual. 2, Install the nuts that hold the video display assem- Check the purity and convergence acbly. cording to the service manual instructions, but adjust ly if required.
  • Connect the power and signal harnesses to the ions, but adjust both only if requi video display. 4, Install the video display shield and bezel. Replace the display frame.
  • Lock the top service door on the cabinet.

NutWasher and Fender Washer Display Display Shield Fi

Figure 3-1 Removing the Video Display

Page 29

S.T.U.N. Runner

Flight Control Maintenance

Routine preventive maintenance of the flight control, involves lubricating the moving parts and checking the mounting screws and nuts for proper tightness approximately every four months. The flight control consists of a handle assembly and a flight control assembly. The handle assembly controls the vertical motion, and the flight control assembly controls the horizontal motion of the display. Routine maintenance can be performed without removing the flight control assembly from the game. Refer to Figures 3-2 and 3-3 for the locations of the parts mentioned in the following procedures.

Routine Maintenance

Routine preventive maintenance on the flight control involves lubricating the moving parts and checking the mounting screws and nuts for proper tightness approximately every four months. Lubrication. Lubricate the flight control assembly pe- ~ tiodically, as follows (see Figures 3-2 and 3-3):

NOTE The handle assembly cover is attached with tamper-proof socket screws. A special 1/8-inch hex-key tool is supplied with each game (Atari part no. 178126-004).
  • Use the special 1/8-inch hex-key tool to remove the screws from the handle assembly cover.
  • Lift off the handle assembly cover and lubricate the following parts inside the flight controls (refer to Figures 3-2 and 3-3 for the position of the lubrication points): ™ Apply two drops of light machine oil lubricant (Atari part no. 107013-001) to the insides of the four shaft bearings. ™ Apply a small amount of WD-40 or a light machine oil to the potentiometer shafts as needed to prevent squeaking. Screw and Nut Tightness. Use the appropriate hexhead and combination wrenches to check the hexhead cap screws and mounting nuts for tightness. Refer to Figures 3-2 and 3-3 for an illustration of the cap screw and mounting nut locations. Maintenance and Troubleshooting

Removing the Flight Control Assembly

NOTE Certain corrective maintenance procedures can be done with the flight control attached to the cabinet. However, for convenience and to avoid damaging the cabinet, we recommend that you remove the flight control from the cabinet before performing any maintenance.

Perform the following procedure to remove the flight control assembly from the control panel:

  • Use a 5/32-inch hex key to remove the four flathead screws that mount the flight control to the cabinet.
  • Carefully guide the flight control through the hole in the control panel.

Disassembling the Handle Assembly

Perform the following procedure to disassemble the handle assembly.

NOTE Removing the handle assembly from the flight control assembly is not necessary to perform the procedure below. However, if you wish to do so, refer to Disassembling the Flight Control Assembly in this chapter for how to separate the two assemblies.
  • Use the special 1/8-inch hex-key tool to remove the four tamper-proof cap screws from the handle assembly cover. 2, Remove the handles and handle adapters.
  • Gently pull the harness wires out of the hollow shaft. 4, Use a 9/64-inch hex driver to remove the cap screw and washer that hold the spring handle pin to the handle assembly shaft.
  • Slide the spring-handle pin out of the shaft.
  • Use a 7/64-inch hex driver to loosen the cap screw that holds the large (60-tooth) spur gear to the shaft.
  • Slide the large (60-tooth) spur gear down the shaft to expose the shaft retainer on the right side.

3-5

Page 30

Maintenance and Troubleshooting

I S

¥

12.

>

o »

WARNING Shield your face and eyes when prying out the retainers because they can fly loose at a high velocity. Cover the retainers with a rag or any material that will trap the retainer.

Use a right-angle slotted screwdriver, or equivalent, to pry the retainer from the shaft. Repeat steps 7 and 8 to remove the retainer on the opposite side. Gently slide the shaft from the housing. Be careful not to lose the torsion springs. . Use a 7/64-inch hex driver to loosen the cap screw that holds the small (14-tooth) spur gear to the potentiometer shaft. Use a 1/2-inch combination wrench to remove the nut and washer that hold the potentiometer to the mounting bracket. Slide the potentiometer from the bracket. Be careful not to lose the small spur gear, nut, and washer. . Use a 5/32-inch hex-head wrench and 3/8-inch combination wrench to remove the two bumpers from the frame. 5, Reassemble the handle assembly as described in the following procedure.

Reassembling the Handle Assembly

Perform the following steps to reassemble the handle assembly (see Figure 3-2):

we Use a 5/32-inch hex-driver and 3/8-inch combination wrench to install the two bumpers on the frame. . Insert the large (60-tooth) spur gear with the collar facing away from the bearing. Hold the gear in line with the bearing hole. (The gear fits through the slot on the right front of the frame.) . Slide the shaft through the right-hand bearing and the spur gear. Do not insert the shaft past the outside edge of the spur-gear collar. . Apply a heavy film of Nyogel 779 lubricant (Atari part no, 178027-001) to the inside of the springs. . Hook the straight end of the first torsion spring through the hole closest to the right side of the frame. . Hold the first torsion spring in line with the shaft so that the looped end of the spring is facing away from the spur gear. . Slide the shaft just through the first torsion spring.

3-6 S.T.U.N. Runner

  • Hook the straight end of the second torsion spring in line with the shaft so that the looped end of the spring is facing the first torsion spring.
  • Hold the second torsion spring in line with the shaft so that the looped end of the spring is facing the first torsion spring.
  • Slide the shaft through the second torsion spring and the left-hand bearing.
  • Position the shaft so that the retainer grooves are just inside the bearings.
  • Install the two retainers in the shaft grooves.
  • Turn the shaft so that the two large holes and the smaller centered hole are facing upward.
  • Locate the hole in the spring-handle pin. Insert the end of the spring-handle pin that is closest to the hole through the slot in the frame and through the hole in the shaft. Make sure that both torsion spring looped ends are wrapped over the springhandle pin. 15, Position the spring-handle pin so that the hole in the pin is aligned with the hole in the shaft.
  • Use a 9/64-inch hex driver to tighten the cap screw and washer that secure the pin to the shaft.
  • Align the cap screw in the spur-gear collar with the threaded hole in the shaft, and use a 7/64-inch hex driver to tighten the cap screw. . Insert the potentiometer shaft through the hole in the mounting bracket. Place the washer, nut, and small (14-tooth) spur gear (with the collar facing inward) onto the shaft before fully inserting the shaft through the bracket.
  • Align the potentiometer so that the tab key is inserted into the keying slot.
  • Use a 1/2-inch combination wrench to slightly tighten the nut on the potentiometer shaft.
  • Turn the potentiometer shaft so that the flat side faces the center wire terminal.
  • Align the cap screw on the small (14-tooth) spur gear with the flat side of the shaft. Use a 7/64-inch hex driver to tighten the cap screw.
  • Slide the potentiometer forward so that the teeth on the two spur gears are tightly meshed; then pull the potentiometer and small (14-tooth) spur gear away from the large spur gear by about 1/64-inch. 24, Use a 1/2-inch combination wrench to tighten the potentiometer to the mounting bracket. Be &

+25, Perform the procedure for installing the harness assembly provided later in this chapter.

  • Install the handle adapters. Do not install the handle covers until the harness is installed and the proper wires are soldered to the trigger switch.
  • Check the vertical potentiometer alignment.
Page 31

S.T.U.N. Runner

28, Install the handle assembly cover and use the special 1/8-inch hex tool to tighten the four tamperproof socket screws that secure the cover to the handle assembly.

Disassembling the Flight Control Assembly =’

Perform the following steps to disassemble the flight control assembly (see Figure 3-3):

  • Unsolder the three harness wires from the vertical potentiometer, handle and trigger microswitch.
  • Use a 5/32-inch hex driver (or ball-end driver) to remove the three cap screws that hold the flight control assembly shaft to the handle assembly frame.
  • Gently pull the two assemblies apart. Make sure the harness wires are free to slide out of the handle assembly shaft. 4, Use a 5/16-inch wrench to remove the anchor nut on the end of the anchor pin. (The anchor nut faces the open end of the frame.)
  • Slide the anchor pin out of the shaft.
  • Grasp the large (60-tooth) spur gear and slide the shaft from the frame. The bearing spacer, torsion springs, and large flat washer will fall free.
  • Use a 7/64-inch hex driver to remove the cap screw holding the large spur gear to the flight control shaft and a 5/64-inch hex driver to remove the set screw that holds the small spur gear to the potentiometer shaft.
  • Use a 1/2-inch combination wrench to remove the nut and washer that hold the potentiometer to the shaft.
  • Unsolder the three harness wires from the potentiometer terminals.
WARNING Shield your face and eyes when prying out the retainer because it can fly loose at a high speed. Cover the retainer with a rag or any material that will trap the retainer.
  • Use a slotted screwdriver, or equivalent, to remove the retainer from the shaft. . Use a 5/32-inch hex driver and 3/8-inch combination wrench to remove the two bumpers from the frame.
  • Reassemble the flight control assembly as described in the following procedure. Maintenance and Troubleshooting

Reassembling the Flight Control Assembly

Perform the following procedure to reassemble the flight control assembly (see Figure 3-3):

  • Use a 5/32-inch hex driver and 3/8-inch combination wrench to install the two bumpers onto the frame.
  • Snap the retainer into its groove in the shaft and slide the large flat washer down the long end of the shaft and against the retainer.
  • Apply a heavy film of Nyogel 779 lubricant (Atari part no. 178027-001) to the inside of the springs.
  • Hook the straight end of the first torsion spring through the hole closest the the rear of the frame. Slide the shaft through the outside bearing and the first torsion spring. . Hook the second torsion spring through the hole on the opposite side and closest to the front of the frame. Slide the shaft through the second spring and the opposite bearing.
  • Turn the shaft so that the threaded hole at the retainer end of the shaft faces up toward the open side of the frame. The hole through the center of the shaft will then be perpendicular to the open side of the frame.
  • Use a 5/16-inch combination wrench to install the anchor pin and nut through the hole in the center of the shaft. Make sure the torsion spring looped ends are wrapped under the anchor pin and nut.
  • Slide the large (60-tooth) spur gear onto the shaft with the collar facing outward. w

9, Align the cap screw in the spur gear collar with the threaded hole in the shaft and use a 7/64-inch hex driver to tighten the cap screw.

  • Insert the potentiometer shaft through the hole in the frame and align the potentiometer so that the tab key is inserted into the keying slot. . Install the washer and nut on the potentiometer shaft but do not tighten.
  • Turn the potentiometer shaft so that the flat side faces the center wire terminal.
  • Align the cap screw on the small (28-tooth) spur gear with the flat side of the shaft and slide the small spur gear (with the collar facing inward) onto the potentiometer shaft. Position the spur gear so that its teeth mesh with those on the large spur gear and use a 5/64-inch hex driver to tighten the set screw. =

Li a Slide the potentiometer forward so that the teeth on the two spur gears are tightly meshed; then slide the potentiometer and small spur gear away from the large spur gear by about 1/64-inch.

3-7

Page 32

Maintenance and Troubleshooting S.TUN. Runner

+7a020-2004 osozee-o1 Tpsens fo oor 196007004

047349.01 Fright Control ‘Decal

047122.02 LeftHand Moaiieaton wa “ a ‘72.8812 119008-1001 o47119-02 : 478012001 SocHdScrew ‘Potentometer Lett Handle _ > Retaining Ring 406007.001 ‘Adapler | °

047122.0: 72.0806 FightHiandie 160050-001 omer 1720201208 git'soxig Moditication Tigger Switch 107-13.001 < a MeTALPar Screw 178249-103 Light Oil (epicue)_~“A9248-00 1 Rorende Cover oe 72-14088 Pan-HD Screw +106007-001 Adhesive

72JA46088 72-8808 =~ VESeCHS oa7iato1 . 177010-238 be) Nyloe Hexut 040284.01 Sanie Seat Handle Spang C 067119.01

ure ee Fight Handle 106007-001 ‘Adépler ‘aanosve (A040247-01 (047188-01 178247-001 Handle Frame ‘Spacer Seth Bracket ‘AS8y

047120-01 Handle Plug 92-6020 ' Butontd Cap ‘Screw 478012.0114 Fiat Washer 106007-001 ‘Adhesive

Figure 3-2 Flight Control Assembly

3-8

Page 33

S.T.U.N. Runner

178027-001 Nyogel (Heavy Lubricant)

017013-001 Light Oit

477010-241 Maintenance and Troubleshooting

179012-001 Retaining Ring

178002-001 Large Washer

042566-01 Steering Shaft

040237.01 Anchor Nut 106007-001 ‘Adhesive

040236-0: Steering Frame

Figure 3-2 Flight Control Assembly, Continued

Page 34

‘Maintenance and Troubleshooting

Flat-Head Screw (2 places)

Flight Control Assy S.T.UN. Runner

Speaker Grille Self-Tapping Screw (4places)

NOTE: The flight control handle has been exploded for clarity (DO NOT remove the handle when removing the dash).

Figure 3-3 Flight Control Removal

  • Use a 1/2-inch combination wrench to tighten the potentiometer to the frame.
  • Slide the bearing spacer over the shaft at the end opposite the spur gears.
  • If necessary, lubricate the flight control assembly as previously described
NOTE The remaining steps describe the procedure for attaching the flight control assembly to the handle assembly.
  • Insert the flight control assembly shaft into the collar on the handle assembly frame.
  • Align the three holes in the flight control assembly shaft with the three holes in the handle assembly collar,
  • Use a 5/32-inch hex driver (or ball-end driver) to tighten the three cap screws.

3-10

  • Install the harness assembly as described in the following procedure.
  • Check the horizontal potentiometer alignment.

Installing the Harness Assembly

Perform the following procedure to install the harness assembly into the flight control (see Figures 3-2 and 3.3):

  • Guide the harness wires into the spur gear end of the hollow flight control assembly shaft.
  • Route and solder the wires to the potentiometers and switches. Note that the wire bundle that goes to the right handle is identified with a labeled sleeve (R).
  • Install the wire ties and the ground clip.
Page 35

ILLUSTRATED

PARTS LISTS

Chapter 4

This chapter provides information you need to order parts for your game. Common hardware parts, such as screws, nuts, washers, and so on usually are not listed in the parts lists. The parts lists (except for the PCB parts lists) are arranged alphanumerically by Atari part number. All Aprefix numbers, which are assemblies, come first. Next are part numbers with six numbers followed by a hyphen (000598- through 201000-). Ending the list are part numbers with a two-number designation followed by a hyphen (00- through 99-). The PCB parts lists are arranged in alphabetical order by component. Within each section the parts are arranged numerically by part number. When you order parts, give the part number, part name, the number of this manual, and the serial number of your game. With this information, we can fill your order rapidly and correctly. We hope this will create less downtime and more profit from your games. Atari Games Customer Service phone numbers are listed on the inside front cover of this manual.

Page 36

Mlustrated Parts Lists S.T.UN. Runner

047274-01 ‘Attraction 176019-212 Shield #10 Tapping Screw

1760274424047276-01047346-01
FrameLock Washer178263-0402iDecal
176013-21278-070021/4" Foam Tape1470003-001
#10 Tapping711" FendernsPoorescent
oeecWasher439017-204471086-001
178263-0402 047275-0175-9515Sa
{ie'FoamDisplay822217/4"Nyy__ideo Displayfuoeecert
TapeShieldWasher Assy:ae

Retaining Clip

042562-02 Flight Control Assy 047349-01 Fit Ctl Decal 176038-4412 4114" Tamperproot Ss Screw ie GCA ease] \. A047229-01 De eaters! \ Cabinet

176019-220 #8 Sq. Dr, Screwisis e izes]ASS

178282-001 Washer Cap Fastener teehee 178282-002 Red Cap Fastener ay,

IFsnS OX[ara 01

ATS Bracket 72-5536 Hex Bolt 047280-01 75-07002 Seat ona" | Fender Caster | Washer 178255-001 177010-244

awhion2AdjustableHex Locknut
Blk Button Ascy3'SGidefo reed
160044-001eneix047347-01Bolt
Snap-Action Switch[430,07 p5-Bhee 25]Z(047286-02 Start Button75-0458
SIN etoeSpeakerDecal047279-01—spjit-Lock
Cay eeBezelformedWasher

ora 047284-01 . Speaker Grille 171093-001* 476019-220 047345-01 Coin Door #8 Sq-Drv Screw Front Decal ‘Assy

Figure 4-1 Cabinet-Mounted Assemblies, Front View A046565-01 D

4-2

Page 37

S.T.U.N. Runner

Items Not Shown:

178126-004 ‘Tamperproof Hex Key 047341-01 Left Side Decal A 047341-03 Left Side Decal 8 047342-041 Left Side Skirt Decal 047343-01 Lett Display Decal 047344-01 Left Attraction Decal 148007-104 41/2" Speaker 176015-112 #10 Pan-Hd Screw

178070-002 Volume Control

04728201 Utility Bracket 176015-110 #10 Pan-Hd Screw

Right Side Decal 8 160034-241 Slide Switch Illustrated Parts Lists

» 047344-02 Right Attraction

047280-01 04734302 Formed Seat Right 178263-0402 Display 1/4" Foam Tape

ao

047249-01 Monitor Door

A047223-01 On/Off Switch Assy 476015-110 #10 Pag-Hd Screw

99-15109 Cash Box 99-15111 Coin Counter

‘A047190-01 ‘Audio PCB Assy 178120-606— ° PCB Support Standott ‘A044998-11 S.LUNN. Runner_| Multi-Sync PCB Assy

‘A047046-01 ADSP II PCB Assy

‘A047350-01 Board Set Assy 72-6616S #6 Pan-Hd Screw 175004-708 Washer 175004-708 ‘Washer Right Side Right Skirt Decal Decal A 047248-01

Figure 4-1 Cabinet-Mounted Assemblies, Rear View A046565-01 D

Page 38

IMlustrated Parts Lists S.T.UN. Runner

Cabinet-Mounted Assemblies Parts List

Part No. Description Part No. Description

A042562-02Flight Control Assembly139017-20419-Inch Color Raster, Standard Resolution
A046349-01Program Plug AssemblyVideo Display
A046990-01Power Supply Assembly148007-1044 1/2-Inch-Diameter 8 Q, 10-Watt Speaker
A047190-01Audio PCB Assembly160044-001Gold Snap-Action Switch

170003-001 — 15-Watt, 18Inch Fluorescent Light A047222-01 Component Bracket Assembly

A047223-01Assembly On/Off Switch171086-001_18-Inch Fluorescent Lamp Fixture
A047229-01Cabinet Assembly17109300125¢/25¢ Coin Door Assembly
A047322-01Main Hamess Assembly175004-706Fiber Washer

175004-708 Fiber Washer A047323-01 Seat Harness Assembly

A047324-01_+5-Volt Hamess Assembly176013-212#10 x 3/4-Inch Tapping Screw
A047325-01Video Harness Assembly176015-110#10 x 5/8-Inch Pan-Head Self-Tapping Screw
A047326-01Component/Audio Harness Assembly176015-112#10 x 3/4-Inch Pan-Head Self-Tapping Screw

176019-220 #8 x 1 1/4Inch Screw A047327-01 Start Harness Assembly

A047328-01Speaker Harness Assembly176020-220#8 x 1 1/4-Inch Black Screw
A047330-01AC Hamess Assembly176027-44241/4-20 x 1.50-Inch Zine Lock Hex Washer

A047350-01_S.T.U.N. Runner Board Set Assembly Screw 176038-4412 1/4-20 x 3/4-Inch Tamper-Proof Flat-Head

046989-01Power Supply Wiring DiagramScrew
047248-01Door177010-244 — 1/4-20 Polymer Hex Locknut

047249-01 Monitor Door

047274-01Attraction Shield178032-002#10 Screw-Down Wire and Cable Tie

178120-606 PCB Support Standoff

047275-01Display Shield178126-0041/8-Inch Tamper-Proof Hex Key Driver
047276-01Attraction Frame178232-001Fluorescent Lamp Retaining Clip

047277-01 ‘Display Frame

047279-01Formed Dash178237-003Black Nylon Button Assembly

178263-0402 1/4 x 1/8-Inch Foam Tape

047280-01Formed Seat178282-001Cap Washer Fastener
047281-01Control Bracket>178282-002_5/8-Inch Red Fastener Cap

047284-01 Speaker Grille

047285-01Light Fixture Panel72-55361/4-20 x 2 1/4-Inch Hex Head Bolt

72-6616S #6 x 1-Inch Pan-Head Deep Thread Screw

047286-01Display Bezel75-07002—1/4-Inch Fender Washer
047286-02Speaker Bezel75-95151/4-20 Nut/Washer Assembly

047321-01 Main Wiring Diagram 047333-01 Installation Hamess These are the technical documents for the 047346-01 Attraction Decal S.T.U.N. Runner game:

047347-01Start Button DecalSP-338§.T.U.N. Runner Schematic Package
04734702Atari Logo DecalST-338S.T.U.N. Runner Self-Test Label
047349-01Flight Control DecalTM-296Wells-Gardner 19-Inch Standard-Resolution

Color Video Display Service Manual ‘TM-338 S.T.U.N. Runner Operator's Manual

4-4 =>

Page 39

Illustrated Parts Lists STUN. Runner

auaindi 1760393608 coe Tamper Preot Cap Screw 106007-001 Adhesive 047349-01

178249-003 - ‘Lett Handle a7 -08 a prety Left Hancte : Mositication Eaepd a #10 Soc-Hd Screw al totgiecwe |“ 040240-01 a "449008-1001 a Bumper "179012001

047119.02geSoc-Hd ScrewPoteatometer
Lelt Handle“iPetanng ra49¢007-001
‘Adapterao\‘Adhesive72.0604

; an 4118" Soc-Hd Screw

aosoaes.o1\5*]‘ton007-001

i ‘AdhesNve rams sy fy 040249.01 ~ ‘Spur Gear

oxriz2.01 160050-001 reese Ron rande s ‘ran20-1200 Tees Nicanon —TgerSwich Pesesaeh 178249-103 (2 pieces nonrende over

Pan-Hd Screw 106007-001

Handle Torsion W2Soc Ho 047121-01 Spring Serew “stop Plate 47010-2908 04024201

Nyloo Hew Nat040244.01Spur GestHande Shat

Handle Spring " 047119.01 72-8604 " Right Handle 114" Soc-Hd Serew 106007-001 ‘Adecner: ‘Adhesive 4040267-01 o471ge-01 —178247-001 Handle Frame Spacer ‘Switeh Bracket ‘Assy

(047120.01 Handle Plug 92.8020 Button-Hd Cap ‘Screw 175012-0114 Flat Washer 106007-001 ‘Adhesive

Figure 4-2 Flight Control Assembly A042562-02 B

4-6

Page 40

STUN. Runner Illustrated Parts Lists

040968-01 Spur Gear 178012-001 Retaining Ring

478002.001 Large Washer

040238.01 ‘Anchor Pin

042834.01 ‘Handle Frame oe * Light Oi!

178101-003 Spur Gear

0a0236.02 Steering Frame

040241.01 Light Oi ‘Spacer Bearing

Figure 4-2 Flight Control Assembly, Continued A042562-02 B

Page 41

Ilustrated Pats Lists S.T.UN. Runner

Flight Control Assembly Parts List

Part No. Description Part No. Description

A040468-01Flight Control Harness Assembly042634-01Handle Frame
72-1408#4-40 x 1/2-Inch Pan-Head Machine Screw047119-01Right Handle Adapter

72-8006 #10-32 x 3/8-Inch Socket-Head Cap Screw

72-8010#10-32 x 5/8-Inch Socket-Head Cap Screw047119-02Left Handle Adapter

047120-01 Handle Plug

72-8604+#6-32 x 1/4-Inch Socket-Head Cap Screw047121-01Stop Plate
72-8606#6-32 x 3/8-Inch Socket-Head Cap Screw047122-01Right Handle Modification

72-8808 #8-32 x 1/2-Inch Socket-Head Cap Screw

72-8812#8-32 x 3/4-Inch Socket-Head Cap Screw047122-02Left Handle Modification

047188-01 Spacer

72-JA4608B#6-19 Black Screw106007-001Penetrating Adhesive
75-07020Flat Washer107013-001Light Oil Lubricant

78-1701 Lubricant

82-8020#10-32 x 1 1/4-Inch Button-Head Cap Screw119008-1001 5 KQ Potentiometer

160050-001 Trigger Switch

040235-0160-Tooth Spur Gear with Hub172020-1208 3/16-Inch Diameter x 1/2-Inch Spring Roll Pin
040236-02Steering Frame175002-001Large Washer for .750-Inch-Diameter Shaft

040237-01_ Anchor Nut

040238-01Anchor Pin175002-004#10 Flat Washer

175012-0114 Flat Washer

040239-01Steering Torsion Spring176039-3604 #6-32 x 1/4-Inch Tamper-Proof Button-Head_
040240-01Stop BumperSocket Screw
040241-01Spacer Bearing177010-238#8-32 Nyloc Hex Nut

04024201 Handle Shaft 177010-241 #10-32 Nyloc Hex Nut

040244-01Handle Spring Pin178012-001Retaining Ring for .750-Inch-Diameter Shaft
040246-01Handle Torsion Spring178027-001Nyogel (Heavy Lubricant)
040248-01Cover178065-1004-Inch Wire and Cable Tie

040249-01 14-Tooth Spur Gear with Hub 178068-001 3/4-Inch Cable Tie Mount

040968-0128-Tooth Spur Gear with Hub178247-001Switch Bracket
042566-01Steering Shaft178248-001Trigger

{

Page 42

S.T.UN. Runner Mlustrated Parts Lists

99-15085 Coin Door Harness

99-15052 99-15038

4 Bezel for Button

99-15116 iy Spring for Bution a 99-15001 thru 99-15012 D Upper Door a Ret. Bution

99-1511399-1502699-15104:Tt99-15039
Key iaCoin inlet, RightBase Platea)rBezel for Cover
99-15056af|eig
Screw for Bezel ©.&99-15036
99-15025cae:Cover
Coin iniet, LeftoA;

@

99-15055“_Ve

> 7 a

Retaining Screwé99-1514

99-15051 — Die Cast Frame Lamp Holder 9015100 Lamp

99-1516 | 99-15053 Lower Door 99-15041 2+. Lockt. Coil Spring Lockout Coil : es 99-15030 ta Lockout Flap 99-15086 7 99-15028 Coin Mechanism Coin Ret. Box 99-15060 99-15027 Coin Ret. Box Saey

i

99-15096’‘yl>\“"99-1508999-1510
Sw. AdjusterFy aeLock AssyEnclosure

99-15029 oe J Bracket ies Ss

99-15042 ‘Switch 99-15060 Sw. Cover

99-15109 _| Coin Box

99-15112 Locking Bar. —11

(Not Included)

99-15111 Coin Counter

Figure 4-3 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

4-9

Page 43

Illustrated Parts Lists S.T.U.N. Runner

Coin Acceptors, Inc. Coin Door Assembly Parts List

Part No. Description Part No. Description

160057-001Coin Switch99-10081Key Holder
70-11-47Miniature Bayonet Lamp99-10096‘Fastener
72-94068#4-40 x 3/8-Inch Truss-Head Screw99-10104Bar Retainer
72-HA1404C_ #4-40 x 1/4-Inch Pan-Head Screw99-10105Bar
72JA1405B — #4-40 x .31-Inch Pan-Head Screw99-0115Spring
75-14128—-#4-40 x 3/4-Inch Pan-Head Screw99-10116Plastic Coin Return Lever
75-9948#4-40 Locknut99-10117Steel Coin Return Door
99-1008—Retainer99-10139Coin Door
99-1042Coin Switch Assembly for Belgian 5 Fr and99-10140Coin Door Inner-Panel Assembly
USS. 25¢99-10141Die-Cast Coin Retum Cover
99-10043Coin Switch Assembly for German 1 DM,99-10143Coin Door Frame
Japanese 100 Yen, Swiss 1 Fr99-10144Channel Clip

99-10044 Coin Switch Assembly for German 2 DM,

Italian 100 L, U.S. $1.0099-10147Harness
99-10045Coin Switch Assembly for Australian $.20,99-10148Lock Assembly
German 5 DM, British 10 P99-10149Service Door

99-10150 Switch Cover 99-10068 Coin Return Chute

99-10075Switch Wire (included in coin switch assembly99-10151Left Coin Inlet
99-10043)99-10152Right Coin Inlet
99-10076Switch Wire (included in coin switch assembly99-10153Coin Return Box
99-10042)99-10154Bracket Assembly

99-10077 Switch Wire (included in coin switch assembly

99-1044)99-10160—_1-Inch Wide Die-Cast Coin Inlet Housing
99-10078Switch Wire (included in coin switch assembly99-016125¢ Amber Side-Entry Coin Button Assembly
99-10045)99-15066Screw for Clamp
99-10080Lamp Socket171006-035Metal Coin Mechanism for U.S. 25¢

4-10 ¥

Page 44

S.T.U.N. Runner Illustrated Parts Lists

A043367-03 6" White 179231-002 Jumper Assy 2 Pos Term Bik

4043367-02 6" Black Jumper Assy

A042384-01 Line Filter Assy

4903-003 5Y, 104 Hitron Power Supply

A043967-01 Jumper Assy

| ~~ 14608-3022 ‘3A, 250V Fuse

14608-2022 142047-001 2A, 250V Fuse Transformer (2 places)

17925-2205 5 Pos Fuse Bik

Figure 4-4 Power Supply Assembly A046990-01 B

4-11

Page 45

Illustrated Parts Lists S.T.UN. Runner

Power Supply Assembly Parts List

Part No.DescriptionPart No.Description
404238401_Line Filter Assembly146008-20222 Amp, 250v Slow Blow Fuse
404336701Jumper Assembly14600830223 Amp, 250v Slow Blow Fuse
A043367-026-Inch Black Jumper Assembly149003-0035-Volt , 10-Amp Hitron Switching Power
043367036-Inch White Jumper AssemblySupply (See Below)

178065-101 _5.5-Inch Wire and Cable Tie 72-HAGO6S #6-32 x 3/8-Inch Screw

72-HA4806S—-#8-32 x 3/8-Inch Screw179225-2205_5-Position Fuse Block
046924-01Base Chassis Power Supply179231-002_2-Position Terminal Block

142047-001_ Transformer

Hitron 5 Volt, 10 Amp Power Supply Subassembly Parts List

Part No.DescriptionPart No.Description
Transistors99-211024Resistor, Carbon Film, 470 Ohm, 5%, 1/4W
99-211002‘Transistor, NPN, 25C1413A99-211025Resistor, Carbon Film, 47 Ohm, 5%, 1/4W.
ae,Transistor; NPN, PEEOSOB99-211026Resistor, Carbon Film, 330 Ohm, 5%, 1/4W

99-211004 Transistor, PNP, PESSS0B Fi

Ps99-211027Resistor, Carbon Film, 5.6 Ohm, 5%, 1/4W

99-211062 Transistor, 2SD725 7 .

99-211063Transistor, PE8350B99-211028Resistor, Carbon Film, 8.2 Ohm, 5%, 1/4W

° 99-211029 Resistor, Carbon Film, 10 Ohm, 5%, 1/4W Diodes 99-211030 Resistor, Carbon Film, 39 Ohm, 5%, 1/4W

99-211005Diode, Schottky, S10SC4M99-211031Resistor, Carbon Film, 56 Ohm, 5%, 1/4W
99-211006Diode, Fast Recovery, 30DF199-211032Resistor, Carbon Film, 1K Ohm, 5%, 1/4W
99-211007Diode, Zener, IN752A99-211033Resistor, Metal Film, 2K Ohm, 2%, 1/4W

99-211008 Diode, Rectifier, IN4006

,99-211034Resistor, Carbon Film, 180K Ohm, 5%, 1W
99-211009Diode, Fast Recovery, RPG10B99-211035Resistor, Carbon Film, 2K Ohm, 5%, 1/4W
99-211010Diode, Fast Recovery, RPG1OK99-211065Resistor, Wire Wound, 27 Ohm, 5%, 2W
99-211011Diode, Fast Recovery, RPG15B99-211066Resistor, Carbon Film, 6.8 Ohm, 5%, 1/2W

99-211012 Diode, Switching, 1N4148

;99-211067Resistor, Carbon Film, 12 Ohm, 5%, 1/4W
99-211064Diode, $15SC4M99-211068Resistor.Carbon Film, 2.4 Ohm, 5%, 1/2W
99-211076Diode, 31DQ0499-211077Resistor, 470 Ohm, 1/2W, 5%
99-211013Rectifier, Silicon Controlled, $280099-211078Resistor, 120K Ohm, 1W, 5%

Resistors Capacitors

99-211014Potentiometer, Trimming, 3k Ohm99-211036Capacitor, Metal Film, 0.047 HF, 250V
99-211015Resistor, Wire Wound, 50 Ohm, 5%, 2W99-211037Capacitor, Metal Film,0.22 lF, 100V
99-211016Resistor, Wire Wound, 150 Ohm, 5%, 2W99-211038Capacitor, Metal Film, 0.1 pF, 400V
99-211017Resistor, Wire Wound, 33 Ohm, 5%, 20799-211039Capacitor, Metal Film, 0.022 HF, 100V
99-211018Resistor, Wire Wound, 0.47 Ohm, 5%, 2W99-211040Capacitor, Ceramic, 1800 PF, 2KV, Z5V
99-211019Resistor, Wire Wound, 120 Ohm, 5%, 2W99-211041Capacitor, Ceramic, 0.01 HF, KV, Z5U
99-211020‘Thermistor, 0.5 Ohm, 5%, SW99-211042Capacitor, Ceramic, 0.001 UF, 2KV
99-211021Resistor, 2.2K Ohm, 2%, 1/4W99211043Capacitor, Ceramic, 470 PF, IKV, Z5P
99-211022Resistor, Carbon Film, 330 Ohm, 5%, /2W99211044Capacitor, Electrolytic, 470 UF, 25V

99-211023 Resistor, Carbon Film, 270 Ohm, 5%, 1/2W

Page 46

S.T.U.N. Runner Illustrated Parts Lists

Hitron 5 Volt, 10 Amp Power Supply Subassembly Parts List

Part No. Description Part No. Description

99-211045Capacitor, Electrolytic, 220 HF, 25V99-211086Inductor, 0.75 MH
99-211046Capacitor, Electrolytic, 100 WF, 200V99-211087Inductor, 2.2 4H
99-211047Capacitor, Electrolytic, 1000 WF, 25V99-211088Inductor, 60 MH
99-211048Capacitor, Electrolytic, 2200 UF, 16VTransformers
99-211049Capacitor, Ceramic, 4700 WF, 400V99-211075‘Transformer, Power
99-211069Capacitor, Electrolytic, 2200 WF, 16V99-211083‘Transformer, Power
99-211070Capacitor, Electrolytic, 220 HF, 25V99-211089‘Transformer, 4.75 MH
99-211079Capacitor, DE7100F22M99-211092Transformer
99-211080Capacitor, 1000 MF, 35V99-211085Transformer
99-211081Capacitor, 470 UF, 25VMiscellaneous

99-211082 Capacitor, 220 UF, 16V

99-211090Capacitor, Ceramic, 1000 PF, 2KVoarii0s6oa
-211091CaElIh221Vveyes
99.19.‘apacitor, Electrolytic,2200 HF, 1099-211057Terminal Block, 8-CKT

Iniluctoes 99-211058 Fuse, 2A, 250V, Semko

99-211050Inductor, 7 HH99-211059Heat Sink
99-211051Inductor, 7 HH, 35MM99-211060Fuse Holder, 635MM
99-211052Inductor, 15 MH99-211061Heatsink, 1.5MM
99-211053Inductor, 1.5 MH99-211072Fuse Holder, 5.2X20
99-211054Inductor, 2.2 HH99-211073Fuse, 2A, 125V
Inductor, 9.8 HH99-211074Terminal Block, 9-CKT

99-211084 99-211085 Inductor, 8 WH Inductor, 9.8 HH

Page 47

IMlustrated Parts Lists S.T.U.N. Runner

N O T E S

4-14

Page 48

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 49

Illustrated Parts Lists S.T.U.N. Runner

S.T.U.N. Runner Multisync PCB Assembly Parts List

DesignatorDescriptionPartDesignatorDescriptionPart No.
Integrated Circuits135KIntegrated Circuit, 744832137487-001
20PIntegrated Circuit, 74A1S574137548-001
208, 20U, 20W Integrated Circuit, 7448823137513-001135MIntegrated Circuit, 741874137023-001
30BIntegrated Circuit, 7415374137144-001135PIntegrated Circuit, 7448573137547-001
30PIntegrated Circuit, 7418245137134-0011350Integrated Circuit, 74AS00137480-001
135WIntegrated Circuit, 7448573137547-001

308, 30U, 30W Integrated Circuit, 2149, 45 nsec 137199-002

30Yit137134-001138¥Integrated Circuit, 7418259137137-001
40H137268-001140cIntegrated Circuit, 7418244137038-001
408, 40U, 40W Integrated Gieuit, 2149, 5 nsec137199002140HIntegrated Circuit, 7419393137146-001
140KIntegrated Circuit, 74F11137583-001
40YIntegrated Circuit, 7418245137134001
45BIntegrated Circuit, ADC0809137243-001140MIntegrated Circuit, 74ALS74137156-001
SOHIntegrated Circuit, 7418123137268-001140PIntegrated Circuit, 7418244137038-001
508, 50U, SOW Integrated Circuit, 74ALS574137548-001140UIntegrated Circuit, 74AS08137484-001
150CIntegrated Circuit, 7418245137134-001
PaIntegrated Circuit, 7448573137547-001
Integrated Circuit, 7415244137038-001150EIntegrated Circuit, 7418244137038-001
eis {605,60U,60W Integrated Circuit, VRAM, 64K x 4,137553-002150HIntegrated Circuit, 741874137023-001
150 nsec (Acceptable substitute is150KIntegrated Circuit, 741820137060-001
64K x 4, 120 nsec VRAM Integrated1508-GSP__Integrated Circuit, 34010-50137538-002

Circuit, part no. 137553-001)

oyIntegrated Circuit, 7445138137522-001150UIntegrated Circuit, 7448573137547-001
65CIntegrated Circuit, 7418259137137-001150WIntegrated Circuit, 74F04137437-001
150YIntegrated Circuit, 74F161137343-001
70P, 708,Integrated Circuit, VRAM,160cIntegrated Circuit, 7418244137038-001
70U,70W64K x 4, 150 nsec137553-002
(Acceptable substitute is 64K x 4160EIntegrated Circuit, 74ALS161137470-001
120 nsec VRAM Integrated Circuit,160HIntegrated Circuit, 74ALS32137464-001
part no. 137553-001)160KIntegrated Circuit, 74ALS138137517-001
70YIntegrated Circuit, 74AS08137484-001160MIntegrated Circuit, 74F04137437-001
75CIntegrated Circuit, 7418259137137-001
75HIntegrated Circuit, 741814137056-001160UIntegrated Circuit, 744832137487-001
160WIntegrated Circuit, 741874137023-001
80MIntegrated Circuit, 74ALS138137517-001170CIntegrated Circuit, 7418245137134-001
1708Integrated Circuit, 7418244137038-001

85P,855,85U,85W Integrated Circuit, VRAM, 64K x 4, 137553-002

150 nsec (Acceptable substitute170HIntegrated Circuit, 7418148137417-001
is 64K x 4, 120 nsec VRAM Integrated170KIntegrated Circuit, 7448161137470-001
Circuit, part no. 137553-001)175RIntegrated Circuit, 7418245137134-001
Integrated Circuit, 74ALS08137460-0011757Integrated Circuit, 744808137484-001

ay 958,95U,95W Integrated Circuit, VRAM, 64K x 4, 137553-002

150 nsec Note: Acceptable substitute is175WIntegrated Circuit, SCOM137526-001
64K x 4, 120 nsec VRAM Integrated180CIntegrated Circuit, 74ALS138137517-001
Circuit, part no. 137553-001180EIntegrated Circuit, 74415139137467-001
100MIntegrated Circuit, 74ALS161137470-001ue0eTmepraved Circle, 260533137146001
110Integrated Circuit, 7406137052-001a
110KIntegrated Circuit, 7AALS138137517-001btbesa PaviaBeen
120HIntegrated Circuit, 74F74137436-001190NIntegrated Circuit, 7418245137134-001
120KIntegrated Circuit, 7415393ws7id6-oo1—* 7096; 200tegrated Cire RAM,157285-006
120MIntegrated Circuit, 74ALS574137548-001°
120PIntegrated Circuit, 7448573137547-001,,3
120S-PSP_—_Integrated Circuit, 34012-50137559-001oercinan atl bone RAMbaa so
1200Integrated Circuit, 74F244137502-001mt 200)een pes enray
120W, 120YIntegrated Circuit, 744$573137547-001:
135C, 135H__Integrated Circuit, 74774137436-001

4-16

Page 50

S.T.U.N. Runner Iustrated Parts Lists

S.T.U.N. Runner Multisync PCB Assembly, Continued Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
C274Capacitor, 47 pF, 100 V, Ceramic122016-470
2001Integrated Circuit, 74ALS32137464-001
200MIntegrated Circuit, 74ALS138137517-001©323-C326Capacitor, 10 pF, 100 V, Ceramic122016-100
200N, 200P —_ Integrated Circuit, 7418245137134-001€332, C333, C343 Capacitor, .1 pF, 50 V, Ceramic122002104
200RIntegrated Circuit, EPROM36070-2102
C344-C347Capacitor, 100 pF, 100 V, Ceramic122016-101
2008Integrated Circuit, EPROM136070-2104C359, C360Capacitor, .001 pF, 50 V, #10% — 122015-102
200TIntegrated Circuit, EPROM136070-2106Diodes
200UIntegrated Circuit, EPROM136070-2108CRI, CR2, CRG, CRI-CR12
200Integrated Circuit, EPROM136070-2110Diode, MV5053, LightEmiting_131027-002
cRI3Diode, 1N4002131048-002
200WIntegrated Circuit, EPROM136070-2112R14Diode, MV5053, Light-Emitting_—131027-002
200YIntegrated Circuit, EPROM136070-1116R18, CR23.Diode, 1N4002131048-002
210C, 210D—_Integrated Circuit, RAM,137535-006

8K x 8, 150 nsec Transistors

210EIntegrated Circuit, 48202-15, RAM — 137442-150Qi, Q2‘Transistor, 2N6044133042-001
s‘Transistor, 2N3904133041-001
210FIntegrated Circuit, 7418245137134-001rod‘Transistor, 2N3906133040-001
210H, 210), 210K Integrated Circuit, 7418244137038-001a‘Transistor, 2N3904133041-001

210L, 210M —_ Integrated Circuit, 7418245 137134-001

210NIntegrated Circuit, 7418244137038-001fers)‘Transistor, 2N3906133040-001
ror)‘Transistor, 2N3904133041-001
210PIntegrated Circuit, 7418245137134-001Quo‘Transistor, 2N3906133040-001
210RIntegrated Circuit, EPROM136070-2101Qi‘Transistor, 2N3904133041-001
2108Integrated Circuit, EPROM136070-2103
210TIntegrated Circuit, EPROM136070-2105Resistors

R1-R10 Resistor, 100 Ohm, $5%, 1/4W — 110000-101

2100Integrated Circuit, EPROM136070-2107R29-R45,Resistor, 1 K Ohm, #5%, 1/4 W—110000-102
210VIntegrated Circuit, EPROM136070-2109RAG-RAS,Resistor, 470 Ohm, #5%, 1/4 W — 110000-471
210WIntegrated Circuit, EPROM136070-2111R49, R50-R54Resistor, 4.7 K Ohm, 45%, 1/4 W110000-472
210YIntegrated Circuit, EPROM136070-1115
R55Resistor, 100 Ohm, +5%, 1/4 W—110000-101
CapacitorsR57-R6OResistor, 1 K Ohm, +5%, 1/4W——110000-102
clCapacitor, 100 HF, 35 V, Electrolytic 124000-107ROLResistor, 4.7 K Ohm, +5%, 1/4 W — 110000-472
c2Capacitor, .01 pF, 50 V, Ceramic122002-103R62, R63Resistor, 220 Ohm, +5%, 1/4 W110000-221
3-C14,Capacitor, .1 UF, 50V, Ceramic-122002-104
C16, C19-C21, C24-C43, C44-CATROBResistor, 1 K Ohm, +5%, 1/4 W — 110000-102
Capacitor, .001 HF, $0 V, +10%122015-102R70-R73,Resistor, 220 Ohm, #5%, 1/4 W — 110000-221
R74, R75Resistor, 10 K Ohm, +5%, 1/4 W110000-103
C65-C78, C86, C87, C94-C106, C116, C117, C123, C124, C131-C137R76Resistor, 220 Ohm, +5%, 1/4W —— 110000-221

Capacitor, .1 MF, 50 V, Ceramic 122002-104

C138, C139Capacitor, 1000 pF, 100 V, Ceramic 122016-102R77, R7BResistor, 4.7 K Ohm, +5%, 1/4. W — 110000-472
C140, C141Capacitor, 1 UF, 50 V, Ceramic122002-104R79Resistor, 47 K Ohm, +5%, 1/4 W — 110000-473
C142Capacitor, .22 WF, 50 V, Ceramic122015-224R80, R81Resistor, 1 K Ohm, +5%, 1/4 W—_-110000-102
R82, R83Resistor, 470 Ohm, +5%, 1/4 W110000-471

C143, C144_——Capacitor, 1 UF, 50 V, Ceramic 122002-104

C145Capacitor, 10 WF, 35 V, Electrolytic124000-106RE4RESResistor, 10 K Ohm, +5%, 1/4. W—110000-103
C146, C155, C158-C185, C187-C189, C193-C202, C204-C227RE9-ROGResistor, 33 Ohm, +5%, 1/4 W110000-330
Capacitor, .1 UF, 50V, Ceramic122002-104RO7Resistor, 3.3 K Ohm, +5%, 1/4 W — 110000-332
R98-R101Resistor, 100 Ohm, +5%, 1/4 W——_110000-101
C28Capacitor, .001 pF, 50V, 10%—-122015-102
C229Capacitor, 47 pF, 100 V, Ceramic122016-470R102-R107__—_—Resistor, 33 Ohm, 45%, 1/4 W110000-330
€230-C238, C243-C249R108Resistor, 3.3 K Ohm, +5%, 1/4 W — 110000-332
Capacitor, .1 HF, 50V, Ceramic122002-104R109-R1L1Resistor, 100 Ohm,45%, 1/4 W110000-101
C250Capacitor, 47 pF, 100 V, Ceramic122016-470RUZResistor, 3.3 K Ohm, +5%, 1/4 W — 110000-332
€251-C259, C264-C273R13-R115Resistor, 100 Ohm, +5%, 1/4 W—110000-101
Capacitor, .1 MF, 50V, Ceramic122002104R1G-R123Resistor, 33 Ohm, +5%, 1/4 W110000-330

4-17

Page 51

Ilustrated Parts Lists S.T.UN. Runner

S.T.U.N. Runner Multisync PCB Assembly, Continued. Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
R125-R131Resistor, 1 K Ohm, +5%, 1/4 W — 110000-102JI6Connector, 11 Circuit, Header, .100 Ctr_179118-011

ar Connector, Header, 60 Circuit, .1 Ctr179021-060

R132Resistor, 4.7 K Ohm, +5%, 1/4 W110000472J8-j10Connector, 11 Circuit, Header, .100 Ctr 179118-011
R134Resistor, 1 K Ohm, £5%, 1/4 W — 110000-102SPEEDConnector, 6 Ckt, Hdr,.100 Ctr.—_-179177-006
RISSResistor, 0 Ohm, £5%, 1/4 W110005-001VCLK.Connector, 6 Ckt, Hdr, .100 Ctr179177-006

R1G4-R167_Resistor, 470 Ohm, +5%, 1/4 W 110000471 Sockets

RIG8-RI71__Resistor, 10 K Ohm, +5%, 1/4 W—110000-1031205-PSP, 1505-GSP Socket, 68 Pin179237-068
R177,R178Resistor, 100 Ohm, +5%, 1/4 W——_110000-101190KSocket, 64 Pin, 900"179256-064
R194Resistor, 10 K Ohm, +5%, 1/4 W—110000-103200ESocket, 24 Pin, .600"179257-024
200KSocket, 20 Pin, .300"179259-020

RN1, RN2 Resistor Network, 470 x 9 Ohm,

£5%, 1/8 W, SIP (10-Pin)118010471200R, 2008, 2007, 200U, 200V, 200W, 200X, 200Y
RN3-RNSResistor Network, R2R Ladder118015-001Socket, 28 Pin, .600"179257-028

RNG Resistor Network, 4.7K x 9 Ohm,

+£5%, 1/8 W, SIP (10-Pin)118010-4722108Socket, 24 Pin, .600"179257-024

210R, 2108, 210T, 210U, 210V, 210W, 210X, 210Y Connectors Socket, 28 Pin, .600" 179257-028 BCLK, SPEED, Connector, Rept, 2 Ckt 179178-002 VCLK Note: Place receptable for SPEED Crystal

on “A” "B", BCLK on “QB”,xOSC2Crystal, 48 MHz, Oscillator Module 144008-003

and VCLK on *QB/2.”

BCLK.Connector, 4 Ckt, Hdr, 100 Cir.—-179177-004Oscillator
SCOMConnector, 11 Circuit, Header, 100 Cur 179118-011XOSC4Oscillator, 40 MHz144008-004
iConnector, 12 Circuit, Header .250 Cur 179069-012XOSCIOscillator, 32 MHz144008-002

Miscellaneous

swSwitch, 8-Position DIP160031-008

Test Point 179051-001

cl

4-18

Page 52

Illustrated Parts Lists S.T.U.N. Runner

or 3B

& Tr Eman] aa oe oe one xe

TeaeeeeT owe | Oe mann Pome wo WO WO HMO a Oa OS

oe Yao

Uae! Ue Sa O° a Dee iF doe ye

e100 RQ. aaa — or Sie Ug Doge eer 0 % . ae emo Se SE ogee

, tle De Sg tee Eas oan p =

oo 3° OnE] UE Se! ee 2957

Te) g “I octet a, DES te Oreo | {cea % a 1 3 9

Dies 180 £26 9

Sh

was) 205 Fee) as

Figure 4-6 ADSP II PCB Assembly A047046-02 C

4-19

Page 53

Illustrated Parts Lists S.T.U.N. Runner

ADSP II PCB Assembly Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
Integrated Circuits7KIntegrated Circuit, 7418259137137-001
ADSP2100_Integrated Circuit, ADSP-2100,7Integrated Circuit, 74A1$74137156-001

16-Bit DSP, PQFP 137629-001

WBIntegrated Circuit, RAM, 8K x 8, 150 nsec137535-0068/9F/H, 8/9H/J Integrated Circuit, 74A1S169137471-001
1cIntegrated Circuit, 7418373137143-0018/9)Integrated Circuit, 741139137097-001
1D, 1EIntegrated Circuit, 7418245137134-0018/9K, 8/9LIntegrated Circuit, 74ALS169137471-001
8A, 8BIntegrated Circuit, 7418245137134001
1FIntegrated Circuit, 7418373137143-001
1HIntegrated Circuit, RAM, 8K x 8, 150 nsec137535-0068C, 8DIntegrated Circuit, 7418244137038-001
2cIntegrated Circuit, 7418373137143-0018EIntegrated Circuit, 7418245137134-001
2D, 2EIntegrated Circuit, 7418245137134-0018FIntegrated Circuit, 7418244137038-001
8HIntegrated Circuit, 74S32137487-001
2FIntegrated Circuit, 7418373137143-001
3A/BIntegrated Circuit, RAM, 8K x 8, 150 nsec137535-0068H)Integrated Circuit, 7418244137038-001
3C, 3D, 3E, 3F Integrated Circuit, 7418244137038-0018KIntegrated Circuit, 74AS00137480-001
3HIntegrated Circuit, RAM, 8K x 8, 150 nsec137535-0068LIntegrated Circuit, 7415244137038-001
9HIntegrated Circuit, EPROM136070-2120
3KIntegrated Circuit, 7418244137038-0019KIntegrated Circuit, EPROM136070-2117

4A, 4B, 4C, 4D, 46, 4, 4H, 4J

Integrated Circuit, 74ALS569137476-0019/10HIntegrated Circuit, OTP, 27C512-250 136070-2121

5A, 5B, 5C, 5D, 5E, 5F, 5H, 5}

Integrated Circuit, SRAM, 4K X 4,9/10KIntegrated Circuit, OTP, 27C512-250 136070-2118
45 ns137537-0039A, 9B, 9C, 9D, 9E, 9F, 10A, 10B, 10C, 10D, 10E, 10F
5KIntegrated Circuit, 7448138137522-001Integrated Circuit, SRAM, 4K x 4, 45 ns 137537-003

10H Integrated Circuit, OTP, 27C512-250 136070-2122

SLIntegrated Circuit, 744508137484-00110KIntegrated Circuit, OTP, 27C512-250 136070-2119
6A, 6BIntegrated Circuit, 7418245137134-001
6C, 6D.Integrated Circuit, 7418244137038-001Cay
gIntegrated Circuit, 7432137487-001clCapacitor, 100 WF, 16 V, Electrolytic 124008-107
€2-C95Capacitor, .1 UF, 50 V, Ceramic122002-104
6KIntegrated Circuit, 74ALS74137156-001
OLIntegrated Circuit, 744504137433-001 ~Diode
7AIntegrated Circuit, 744LS32137464-001CRI-CR3Diode, MV5053, Light-Emitting131027-002
7B, 7CIntegrated Circuit, 74A1S138137517-001

Resistors

7Integrated Circuit, 7418244137038-001RL-RI2Resistor, 10 K Ohm, +5%, 1/4 W_110000-103
aIntegrated Circuit, 7448138137522-001R13, R14Resistor, 150 Ohm, +5%, 1/4 W — 110000-151

RIS Resistor, 220 Ohm, #5%, 1/4 W — 110000-221

RIG-RISResistor, 10 K Ohm, +5%, 1/4 W110000-103

R19-R23, R48, RADResistor, 1 K Ohm, 45%, 1/4W —110000-102

Page 54

$.T.U.N, Runner Illustrated Parts Lists

137401-001

o ” roy re is

re 137535-006 436070-1123 rs 198070-1127, t

o ~ o ~ S 196070-1120

it 2093 4

= [| + | orn a: 437607-001

wm

Figure 4-7 Stand-Alone Audio I PCB Assembly A047190-01 B

4-21

Page 55

Ilustrated Parts Lists

Stand-Alone Audio If PCB Assembly S.T.U.N. Runner

Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
CircuitsC24-C36Capacitor, .1 WF, 50V, Ceramic——-122002-104
1A/BIntegrated Circuit, TDA2030137301-001
1c/DIntegrated Circuit, OTP, 300 ns_——-136070-212737Capacitor, .22 WF, 50 V, Ceramic122017-224
1D/EIntegrated Circuit, OTP, 300 ns136070-2126C38Capacitor, .0068 YF, 50 V, Ceramic122015-682
1E/FIntegrated Circuit, OTP, 300 ns——_-136070-212539Capacitor, .22 HF, 50 V, Ceramic122017-224
C40, C41Capacitor, 10 pF, 25 V, Electrolytic124009-106

1E/H Integrated Circuit, OTP, 300 ns_———-136070-2124

2aIntegrated Circuit, TLO84CN137579-001C42.C45Capacitor, .1 UF, 50 V, Ceramic122002-104
2E/FIntegrated Circuit, MSM6295C46Capacitor, 10 UF, 25 V, Electrolytic124009-106
(Surface-Mount)137607-001c47-C49Capacitor, .1 UF, 50 V, Ceramic-122002-104
25 /HIntegrated Circuit, 741874137023-00150Capacitor, 100 pF, 100 V, Ceramic122016-101
3B/C, 3C/D _ Integrated Circuit, TLO84CN137579-001C51Capacitor, .1 UF, 50 V, Ceramic122002104
3r/HIntegrated Circuit, 741886137079-001C52-€55Capacitor, 100 pF, 100 V, Ceramic122016-101
4aIntegrated Circuit, YM3012137402-001C56-C66Capacitor, .1 HF, 50 V, Ceramic122002-104
5EIntegrated Circuit, 74L$174137122-001C67Capacitor, 39 pF, 100 V, Ceramic122016-390
SFIntegrated Circuit, 741874137023-00168Capacitor, .1 HF, 50 V, Ceramic——-122002-104
SHIntegrated Circuit, 7419393137146-001
6AIntegrated Circuit, YM2151137401.001Diodes
6BIntegrated Circuit, 4066B137580-001CR1, CR2Diode, MV5053, Light-Emitting131027-002
CR3Diode, 1N754 A, Zener131002-001
TEIntegrated Circuit, 7415138137177-001CR4, CRSDiode, 1N4001131048-001
TFIntegrated Circuit, 741814137056-001CRO-CRODiode, 1N5401131051-002
THIntegrated Circuit, 7418393137146-001
8cIntegrated Circuit, RAM, 8K x 8,R10Diode, MV5053, Light-Emitting131027-002
150 nsec137535-006R11, CR12Diode, 1N4001131048-001
9EIntegrated Circuit, 741273137040-001Heat Sink
10AIntegrated Circuit, 6502 A137577-001HS1Heat Sink178190-032

10c Integrated Circuit, EPROM, 300 nsec 136070-2123,

10EIntegrated Circuit, 7418240137251-001Inductor
ratInductor, 100 wH141002-001
1cIntegrated Circuit, PALIGL8136056-2101
12€Integrated Circuit, SCOM137526-001‘Transistors
Uw‘Transistor, 2N3904133041-001
Capacitors3-05Transistor, 2N5306133033-001
clCapacitor, .22 MF, 50 V, Ceramic—122017-2246Transistor, 2N3904133041-001
c2Capacitor, 22 UF, 35 V, Electrolytic—124000-226
C3, C4Capacitor, .1 MF, $0 V, Ceramic—_-122002-104Resistors
(os)Capacitor, .22 MF, 50 V, Ceramic_-122017-224R1Resistor, 1 Ohm, +5%, 1/8 W110027-010
R2, R3Resistor, 1 K Ohm, 45%, 1/8 W—110027-102
rodCapacitor, 3300 HF, 25 V,RSResistor, 180 Ohm, +5%, 1/2W110001181
Electrolytic, Radial123003-338RSResistor, 22 K Ohm, +5%, 1/8 W—110027-223,
c7-€10Capacitor, .1 UF, 50 V, Ceramic-122002-104
cuCapacitor, 10 WF, 25 V, Electrolytic124009-106R6Resistor, 10 K Ohm, +5%, 1/8 W—110027-103
c12-c14Capacitor, .1 UF, 50 V, Ceramic——-122002-104R7Resistor, 1 K Ohm, +5%, 1/8 W——110027-102
R8Resistor, 10 Ohm, +5%, 1/4 W110000-100
C15Capacitor, 3300 UF, 25 V,RDResistor, 20 K Ohm, +5%, 1/8 W110027-203

Electrolytic, Radial 123003-338

C16Capacitor, .001 UF, 50 V, Ceramic122002102R10, R11Resistor, 12 K Ohm, 45%, 1/8 W110027-123
cl7Capacitor, 3300 pF, 50 V122015-332R12Resistor, 6.8 K Ohm, +5%, 1/8 W — 110027-682
C18Capacitor, 0022 iF, 100 V, Plastic121022-222R13Resistor, 20 K Ohm, +5%, 1/8 W110027-203

RI4 Resistor, 10 K Ohm, #5%, 1/8 W — 110027-103

cyCapacitor, .0068 HF, 50 V, Ceramic122015-682
C20Capacitor, .001 UF, 50 V, Ceramic — 122002-102RISResistor, 6.8 K Ohm, +5%, 1/8 W — 110027-682
C22Capacitor, .015 UF, 100 V, +5%,R16Resistor, 16 K Ohm, +5%, 1/8 W—-110027-163
Poly, Radial126009-153RISResistor, 560 Ohm, +5%, 1/8 W110027561

4-22

Page 56

S.T.U.N. Runner Mlustrated Pants Lists

Stand-Alone Audio Il PCB Assembly, Continued Parts List

DesignatorDescriptionPart No.DesignatorDescriptionPart No.
RIDResistor, 470 Ohm, 45%, 1/8 W — 110027-471R59Resistor, 240 Ohm, +5%, 1/8 W — 110027-241
ROOResistor, 100 K Ohm, 45%, 1/8 W110027-104
R20, R21Resistor, 100 K Ohm, 45%, 1/8 W110027-104+R61Resistor, 470 Ohm, #5%, 1/8 W110027-471
R22Resistor, 15 K Ohm, +5%, 1/8 W110027-153
RBResistor, 7.5 K Ohm, +5%, 1/8 W110027-752R62Resistor, 0 Ohm, +5%, 1/4 W110005-001
R24Resistor, 15 K Ohm, 45%, 1/8 W110027-153ROBResistor, 220 Ohm, +5%, 1/8 W—-110027-221

R64, ROS Resistor, 150 K Ohm, +5%, 1/8 W — 110027-154 R25 Resistor, 30 K Ohm, £5%, 1/8 W — 110027-303

R26Resistor, 10 K Ohm, +5%, 1/8 W—110027-103Connectors
R27Resistor, 47 K Ohm, +5%, 1/8 W — 110027-473ACDCConnector, 12 Ckt, Header,
R28Resistor, 33 K Ohm, 45%, 1/8 W110027-333156 Ctr, Key 11179213012

COIN Connector, 11-Ckt, Header, .100 Ctr 179118-011

R29Resistor, 1 K Ohm, 45%, 1/8 W — 110027-102SCOMConnector, 11 Ckt, Header, .100 Ctr 179118-011
R30Resistor, 2 K Ohm, 45%, 1/8 W — 110027-202SPKRConnector, 2 Ckt, Header, .156 Cur.179213-002

R31 Resistor, 150 K Ohm, +5%, 1/8 W — 110027-154

R32Resistor, 10 K Ohm, +5%, 1/8 W—110027-103Miscellaneous
R33Resistor, 68 K Ohm, +5%, 1/8 W — 110027-683Socket, 20 Pin, 300"179259-020
R34Resistor, 10 Ohm, +5%, 1/4 W110000-100Socket, 24 Pin, .600"179257-024
R35, R36Resistor, 7.5 K Ohm, +5%, 1/8 W — 110027-752Socket, 28 Pin, .600"179257-028
R37Resistor, 15 K Ohm, +5%, 1/8 W110027-153Socket, 40 Pin, .600"179257-040
R38Resistor, 30 K Ohm, 45%, 1/8 W — 110027-303GA/B)Nut/Washer Assy, #6-3275-9516
R39, RAOResistor, 10 K Ohm, 45%, 1/8 W —_ 110027-103GA/B)Screw, Pan Hd, Cross-Recessed,
R41Resistor, 1 K Ohm, £5%, 1/8 W110027-102#6-32 x 3/8" Long72-1606S
RQResistor, 470 Ohm, 45%, 1/8 WW110027-471

AGNDI, +#1005V1, GND1, GND2, CC1+, CCl-, CC2#, CC2-

R43Resistor, 1 K Ohm, +5%, 1/8 W—_-110027-102Test Point179051-001
R44Resistor, 470 Ohm, +5%, 1/8 W—-110027-471swiSwitch, Slide, SPDT160040-001
R45Resistor, 1 K Ohm, £5%, 1/8 W — 110027-102vR1Potentiometer, 10 K Ohm, Horiz.119022-103
RAG, RATResistor, 10 K Ohm, 45%, 1/8 W—110027-103,x1Crystal, 3.579 MHz144007-001
a/B)‘Thermal Compound78-16001
RAB-RSS,Resistor, 1 K Ohm, 45%, 1/8 W110027-102

4-23