CATHODE RAY TOMES

Cloak & Dagger TM-242 1st Printing

Cloak & Dagger (rev 5) (Atari, 1983) · Technical Manual · 64 pages · 50 sections · original scan

Page 1

OPERATORS MANUAL WITH ILLUSTRATED PARTS LIST ‘M-242 1st printing

Page 2

Atari Customer Service

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at one of these Atari Customer Service offices:

UNITED STATES

Parts and Service

Atari, Inc. California Customer Service Office 737 Sycamore PO. Box 906 Milpitas, CA 95035 Telex 17-1103 (Monday-~Friday, 7:30-4:00 pm Pacific Time) From California, Alaska, or Hawaii (408) 943-1120

Ss From anywhere else in the continental United States

toll-free (800) 538-1611 = yO}

EUROPE

Parts and Service

Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 (Monday-Friday, 9:00-6:00 pm GMT) BS 062-52155

Page 3

OPERATORS MANUAL WITH ILLUSTRATED PARTS LIST

*A trademark of and licensed by Universai City Studios, Inc.

Page 4

CLOAK & DAGGER

© 1983 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission from. the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. Ifinfringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, Or operation of a copy of video games made by us, Anyone who purchases such copies risks forfeiting such a game.

Published by: ATARI, INC. 790 Sycamore Drive PO, Box 906 Milpitas, California 95035

Printed in the U.S.A. 12M

Page 5

CLOAK & DAGGER

Notice Regarding Non-ATARI Parts

Use of non-ATARI parts or modifications of any ATARI® game circuitry may adversely affect the safety of your game, and may Cause injury to you and your players.

‘You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following: © Substitute non-ATARI parts in the game.

  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits fora Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, whichare designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following:

  • All green ground wires in the game are properly connected as shown in the game wiring diagram. © The power cord is properly plugged into a grounded three-wire outlet. *® The game printed-circuit boards (PCB) are properly installed within the Electromagnetic Interference (EMI) cage. ° The EMI Shield PCB is properly installed and connected in series with the game PCB harness. © All filter capacitors required on the EMI Shield PCB are properly soldered in place. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area.

iii

Page 6

CLOAK & DAGGER

Table of Contents

Set Up How to Use This Manual Game Overview Option-Switch Location ... Selecting the Coin and Credit Game Play. ...- 60... ec eee eee Attract Mode . : Play Mode Hints for Game Play High-Score Mode

Self Test

SelfTest Displays 0.66... ec cette eee

Maintenance Opening the Control Panel Removing the Joystick Assembly . . . Disassembling the Joystick Assembly . Reassembling the Joystick Assembly Removing the Joystick Leaf Switches Adjusting the Joystick Leaf Switches .. . Pushbutton Leaf Switch Start Switches ..

Illustrated Parts Lists For a list of all ilhustrations in this manual, see the following page. 1-2

1-4

2-2

3-2 3-2 3-2 3-2 3-4 3-4 3-4 3-4

Page 7

List of Illustrations

Figure 1-1

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5

Figure 3-1 Figure 3-2

Figure 4-1 Figure 4-2

Figure 4-3 Figure 4-4 Figure 4-5

Figure 4-6 Figure 4-7 Figure 4-8

Table 1-1 Table [-2

Table 2-1 Table 2-2 Option-Switch Location... 0... te eee

Microprocessor and Looping Tests nan Self-Test Menu Display Color Bar Test Display Option Menu Display ....... Statistics Summary Display . . .

8-Position Joystick Assembly ...... Wire Connections to the Control Panel ....

Mlustrated Parts Lists CLOAK & DAGGER Retrofit Kit Contents for Defender .........-..- CLOAK & DAGGER Retrofit Kit Contents for Joust, Robotron: 2084, and. Stargate . : Control Panel Assembly . . 8-Position Joystick Assembly . Electromagnetic Interference (EMD) Cage Assemblies and PCB Mounting Hardware . EMI Shield PCB ........... CLOAK & DAGGER Master PCB Assembly . . CLOAK & DAGGER Slave PCB Assembly . .

List of Tables

Switch Settings for Coin and Credit Options . . Scoring ............2.005

Self-Test Screen Definitions . . LED Activity............. CLOAK & DAGGER

4-8 4-10

4-12

» 424

Page 8

CLOAK & DAGGER

vi

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found throughout this manual where they apply.

A&A WARNINGS A Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection. Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game’s power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part ofthe game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. ‘To discharge the CRT: Attach one end ofa large, well-insulated, 20-kV jumper to ground. Momentarily touch the free end of the grounded jumper to the anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ATARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care. If you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fly six feet or more from the implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION

Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do notslip on easily, do not force them. A reversed connector may damage your game and void. the warranty.

Page 9
WARNING Shock Hazard ‘To avoid ciectrical shock, do not plug in the game until it has been inspected and properly set up for the line voltage in your area. Do not touch internal parts of the display with your hands or metal objects!

(TT 13

Set Up

How to Use This Manual

This manual, written for game operators and service technicians, describes your new Atari Cloak & Dagger game. Chapter 1 contains a game overview, switch locations, and option information. Chapter 2 contains self-test procedures. Chapter 3 contains maintenance and repair procedures. Chapter 4 contains illustrated parts lists. Notes in this chapter refer you to other places in the manual for more detailed information. Schematic diagrams of the game circuitry are included as a supplement to this manual.

Chapter 1

Page 10

SetUp

Game Overview

Agent X™, complete with trenchcoat, Bogie hat, and briefcase, hurries through a series of adventures and misadventures 1 retrieve stolen plans and destroy dastardly Dr. Boom’s subterranean bomb factory. Our masked hero descends to the depihs of Dr. Boom’s laboratory in a special elevator. On each floor he encounters a series of conveyor belts that are moving explosives. A giant bomb ticks down the game seconds while devices of Dr. Boom’s plotting, such as bomb converters, forklifts deflecting shots back at Agent X, robot guards, acid pits, and craw!ing eyes shooting death rays, challenge the player(s).

WARNING Shock Hazard To avoid electrical shock, do not plug in the game until you have inspected the game. This game should only be connected to a grounded 4-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to instalia grounded outlet Players may receive an electrical shock if this game is not properly grounded! Do not touch internal parts of the display with your hands or with metal objects! CLOAK & DAGGER

Option-Switch Location

Figure 1-1 shows the location of the dual-inline-package (DIP) switch at 5A on the Masier Printed-Circuit Board (PCB). This switch provides coin-option choices.

Selecting the Coin and Credit Options

Settings for the coin and credit options are listed in Table 1-1. Options preset at the factory are shown by the ~4symbol; however, you may change the settings according to your needs. Table 1-1 lists settings for the DIP switch at location 5A on the Master PCB. This switch is used to select coin and credit options available for the left and right coin mechanisms. To verify other option selections, check the self-test display that appears in the SelfTest Mode as described in Chapter 2.

NOTE The SelfTest Mode of CLOAK & DAGGER includes an options display that enables you to select game options. The option switches on the Master PCB are for coin options only. See Chapter 2 for more details.

Interconnect PCB OFF

5A ON

Master PCB

NOTE ON and OFF directions will be reversed in the Defender Cabinet.

Figure 1-1 Option-Switch Location

Page 11

CLOAK & DAGGER

Set Up

Table 1-1 Switch Settings for Coin and Credit Options

Settings of 8-Toggle Switch on CLOAK AND DAGGER Master PCB (at 5A)

234567

8 Option

On Off

Off Off

Off On

Off Off Off

Off Off On

OffOnOff
OffOnOn

Not used

off Off

Demo Freeze Mode On Demo Freeze Mode Off<4

Right Coin Mechanism 1 Credit Added for 1 Coin<¢ 2 Credits Added for 1 Coin

Left Coin Mechanism 1 Credit Added for 1 Coin 4 Credits Added for 1 Coin 5 Credits Added for 1 Coin 6 Credits Added for 1 Coin

Off Free Play Off 1 Credit Required for 1 Game (or I Player) On 1 Credit Required for 2 Games (or 2 Players) On 2 Credits Required for 1 Game (or 1 Player)

4.Manufacturer’s recommended settings Game Play CLOAK & DAGGER is a One- or two-player game with a color raster video display. You control Agent X as he descends underground floor by floor in an elevator to Dr. Boom’s lab, located on the 33rd floor. Your main goal is to retrieve Top Secret plans that are surrounded by an electrical arc. To stop the electrical current, Agent X must shoot all the fiery nodes as he fights off robot guards. As Agent X leaves the elevator on each floor, he must make his way carefully and quickly across the screen to another exit. Each floor displays a configuration of conveyor belts moving green unarmed and red armed explosives. Agent X can pick up the green explosives. The red explosives will explode on contact. Some floors have marauding robot guards, death-ray shooting crawling eyes, and acid pits. Once Agent X has the top secret plans in hand, he must make his way back to the surface. If he exits on a floor that was bombed on the way down, he will find a massive crater protected by node monsters and the previously mentioned attackers. If he exits on a floor that was not bombed, a superguard will join the other attackers to challenge Agent X. On the final level, rumors are that he will meet the notorious Dr. Boom himself.

CLOAK & DAGGER has four possible modes of operation: Attract, Game Play, High-Score, and Self-Test.

Attract Mode

The Attract Mode begins when power is applied to the game, or when the Play, High-Score, or Self-Test Modes end. The Attract Mode ends either when a credit is entered and the game goes into Play Mode, or when the self-test switch is set to on. The message INSERT COIN alternates with the message GAME OVER if the game has no credits. The message PRESS PLAYER I (or 2) START should flash if credits are present, The message CREDITS: X is displayed in the lower right corner of the screen. ATARI 1983 appears in the lower left corner of the screen.

The first screen in the Attract Mode is the Scoring Screen. Agent X appears at the top left of the display walking back and forth on a moving conveyor belt while messages appear beneath the conveyor belt explaining the scoring for each target in the game.

Scoring Screen Text: (1 of 5 coin messages) MAP STEP ON UNARMED EXPLOSIVES

FOR POINTS! (100 points) SECRET MAPS TO NEXT MINEFIELD! SHOOT EXPLOSIVES! INEXTRA LIFE!!! MAP MAP

MYSTERY: BONUS POINTS SLOW SPEED... DOUBLE SPEED! X-LIFE!! ATARI 1983, CREDITS: X

Ifno credits are entered, the second screen in the Attract Mode displays sample game play, which varies. Screen 2 may show floors 1— 3, 5-7, or 9. Floors 4 and 8 are not shown.

Page 12

Set Up

The third screen in the Attract Mode is the high-score screen, The upper portion of the screen displays a table containing the ten all-time highest scores followed by a blue line. initials and scores for the twenty next highest scores entered since the game was last turned onare listed under the blue line. The copyright message appears at the bottom left of the screen. The game retains and displays the top ten scores achieved by players even if the power is turned off and then on again. The fourth screen displayed in the Attract Mode is the logo screen. The CLOAK & DAGGER logo appears as Dr. Boom Icbsa bomb at Agent X. The ampersand (&) appears in an explosion as Agent X fires at Dr. Boom.

Play Mode

The Play Mode begins when sufficient coins have been deposited in the game's coin mechanism to credit the game, and the 1-player or 2-player start button is pressed. This mode ends after the last life has been lost during game play os the player returns to the surface (end of game). At the center of the display, a double-coiled fuse to a giant bomb is ticking down the game seconds for each level. Agent X can light the fuse ina rush for bonus points, but must be able to escape that level before the bomb explodes, If the fuse has shortened on its own to one coil. it lights automatically and prompts Agent X to make a mad dash to the waiting elevator. The doors close just as a burst of light from the explosion is seen. The game’s perspective now changes to a full view inside the elevator. Messages flash across the elevator to give helpful hints on the next level. Dr. Boom has placed explosive mines on every fourth floor. On each of the preceding three floors Agent X can pick up asecret map box that will show him part of the safe path across the minefield on the next fourth floor. CLOAK & DAGGER

Agent X’s first goal is to travel successfully from one elevator to the other; his second goal is to pick up a secret box to get a map of the minefield on levels 4, 8, 12, 16, 20, 24, 28, and 32; the third goal is to light the bomb fuse and escape before the explosion. As game play progresses, Agent X may find an extra-life box and a mystery box that give bonus points, double speed, haif speed, and occasionally, an extra life. Extra bonus points are earned for picking up green unarmed explosives or for skipping floors. 1fAgent X succeeds in capturing the top secret plans, he must fight his way back up to the top ievel. The appearance of box compressors, crawling eyes, and other enemies are more random on the way up than on the way down. If Agent X makes it back to the surface, a free game will be awarded (depending on the settings of the option Switches). The game ends when you use up your last life or successfully make it to the surface. The words GAME OVER appear in the 2-player game only.

Hints for Game Play © Develop skill for controlling the 8-position joysticks.

  • Memorize the mine fields.
  • Destroy the crawling eyes by spreading out shots. © Judge timing through the box compressors that first appear on devel 17. © Jearn levels where it is best NOT to shoot everything. See Table 1-2 for a complete description of how points are scored im CLOAK & DAGGER.
Page 13

CLOAK & DAGGER

Table 1-2 Scoring

Action

Points Bonus

~ Points

Shooting cave walls1None
Shooting unarmed explosives10None
Shooting armed explosives50100
Shooting sleeping guard50,160
Picking up armed explosive100100
Shooting alert guard200100
Shooting lab arc-node200None
Picking up mystery box200-1800100
Shooting node monster1000106
Shooting crawling eye1000200
Shooting super-guard2000200
Shooting Dr. Boom50,000None
Picking up secret plans100,000None

Lighting fuse (the shorter the

fuse the more points awarded)02000-9000
Note: Once fuse is lit, all points awarded are doubled! Set Up

High-Score Mode

The High-Score Mode screen appears with the following alternating messages:

GAME OVER INSERT COIN or PRESS PLAYER 1 (or 2) START If a player ranks among the top 30 scorers, he will see the ten top players listed. Three blue boxes for entering initials appear on the display. A green alphabet is located beneath the boxes. The player uses the left joystick to select an initial and the IGNITER pushbutton to set that initial in a box or to rub out an initial. The message PLAYER I for 2) RANKING: (1-30 or NOTIN TOP 30) appears at the bottom of the screen. If player is not in the top 30 scorers group, the High-Score Mode screen contains the same picture used in the Attract Mode to display the high scores with the added message: PLAYER I (or 2) NOT IN TOP 30.

1-5

Page 14

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 15

Self Test

This game will test itself and provide data to show that the game circuitry and controls are operating properly. Selftest data is presented visualiy on the video display and audibly through the speakers. No additional equipmentis required. We suggest you perform a self-test when you first set up, each time you collect money, change the game options, or suspect game failure.

Chapter 2

Page 16

Self Test

‘Toenter the self-test mode, turn on the selftest switch. The self-test switch is located on the utility panel of ATARY-built games. On converted games not originally manufactured by ATARI, the self-test switch is the locking spring-loaded pushbutton switch located on the game coin door. This switch is labeled AUTO-UP, MANUAL DOWN, 7o exit the self-test mode, press the switch down into its locked position.

NOTE Self-test will not start during game play or during the game-play section of the attract mode.

Self-Test Displays

When the self-test switch is turned on, the screen displays part of the RAM test approximately five different screens) fora few seconds. Figure 2-1 shows the screen that appears when the RAM tests and master microprocessor tests are successfully completed.

NOTE CLOAK & DAGGER contains two microprocessors that are referred to in the self test as master and slave. All test results on the screen come from the master microprocessor. The master microprocessor performs its own self test before trying to send or receive messages from the slave microprocessor. If the master microprocessor fails any part of its self test, the slave Microprocessor cannot perform its self test. If the master microprocessor performs its self tests successfully, but cannot send to or receive Messages from the slave microprocessor during the SLAVE COM test, no slave self-test results appear on the screen. In that case, the game begins a series of looping tests. Once the looping tests begin, enter the self-test menu by turning off the self-test switch. The EXIT function on this menu returns the game to normal game piay.

When seif test starts, the following tests are performed in. order. The results appear on the screen. See the text following Table 2-2 for further explanations of each test. CLOAK & DAGGER

Fable 2-1 Self-Test Screen Definitions

Screen Message Definition

MASTER RAM Checks specific addresses in the Master microprocessor main memory. MASTER ROM Computes the checksums for all of the master program EPROM integrated circuits. MOTION RAM Checks specific addresses in the master microprocessor main memory. EAROM PARITY Checks parity of the two option areas that store game options. MASTER INT Checks the master microprocessor for interrupts and VBLANK activity. SLAVE COM Checks operations and interface citcuitry of the slave microprocessor. SLAVE RAM. Checks specific addresses in the stave microprocessor memory. SLAVE ROM Computes the checksums for all of the slave progcam EPROM integrated Circuits. SLAVE INT Checks that the slave microprocessor is receiving interrupts. ‘Tests the slave microprocessor RAM. buffers. Checks the clock-stretching and priority-access circuitry used by the communications RAM. BITMAP RAM

SHARED RAM

(The following messages refer to the looping tests for switches.) OPT SWTCHS Checks the option switch at position 5A on the Master PCB. Checks the 1-player and 2-player start switches, PLA SWTCHS

DIR SWTCHS Checks bits for VBLANK and [GNIT ER, coin, and self-test switches. JOYSTICKS Checks the movement of both joysticks. SOUND NUM Displays the index of the sound or music currently playing.

If the display screen is blank after the self-test switch is turned on, the two light-emitting diode (LED) switches on the control panei (1-player start and 2-player start) may be used to check the progress of the self-test routine. Neither LED should light up until pressed during the jooping tests, aithough both LEDs flash on briefly when the self test is first entered. If LED activity does not occur at the start of self test, see Table 2-2.

Page 17

CLOAK & DAGGER Self Test

2-Player Start Press to start or stop game sounds. An * appears next tothe sound number to The option switch is located at SA on Master PCB. indicate that the volume Naveed

has been turned off

1-Player Start Pressto start or stop the Not Used motion-object parade, or to Can be either 1 or 0 repeat the playing of a current sound. ; G Not used on000 Right Coin Switch

Not Used Self-Test Switch Should always be 0 Baa (active ow)

VBLANK ay ei ee ' .-—_—_ Flickering between states (1 &O)is normai

Auxiliary Coin Switch | Left coin Switch Joystick Direction

Looping Test Toggle Switches

Looping Test Toggle Switches Press IGNITER button o start or stop test. See detail above.

Motion-Object Parade Sound Identifier

Figure 2-1 Microprocessor and Looping Tests Display

Page 18

Self Test

Table 2-2. LED Activity

LED Activity Meaning,

player LEDon if the display screen is blank, suspect a possible playfield-stamp RAM failure, cathode-ray tube failure, or an inability to clear the bitmap RAM. Both LEDs on The game did not start the self test—probably due to no clock or a PCB failure, Check the power-on reset circuit. Indicates that the self-test routine found an error in the master RAM. 2-player LED off, t-player LED on Both LEDs off if the screen is not usable, the self test is probably running, but cannot write to the playfield-stamp RAM. If you hear the sounds start in 15-20 seconds, the entire self-test routine has run correctly; it just could not report its results tothe screen.

MASTER RAM Test

The MASTER RAM test checks the master microprocessor main memory from hexadecimal iocations 0000 through OFFE. If the MASTER RAM test fails, the screen displays the following message to show the bad integrated circuit (IC) on the Master printed-circuit board (PCB): MASTER RAM BAD; LOC 4L-M The LOC on the screen means location; 41-M is the location of the defective IC. If an error occurs during this test, no further tests are performed, If the MASTER RAM test passes, all master microprocessor tests are performed whether or not they pass.

MASTER ROM Test

NOTE For proper results in this test, bit 3 of the option switch at location 5A on the Master PCB shouid always be OFF.

The MASTER ROM test Computes the checksums for every Master program EPROM IC. Ifa checksum is not correct for the IC under test, the screen displays the following message to show the location of any faulty IC on the Master PCB: MASTER ROM BAD, LOCS: 2D;2F;2H-j,2K 2D, 2E 2H-], and 2K are the locations of the master program memory ICs. CLOAK & DAGGER

NOTE if an error occurs during this test, the master microprocessor continues to perform the remaining tests, However, if the IC at location 2K is bad, all self-test results may be wrong because this is the IC that contains the self-test program!

MOTION RAM Test The MOTION RAM test is exactly like the MASTER RAM test described previously, except that the hexadecimal locations of the area under test are from 3000 to 30FF. Ifan error occurs during this test, the screen displays the following message to show the bad IC on the Master PCB: MOTION RAM BAD; LOC nn The 727 is GL or 6M—the location of the defective IC. If an error occurs during this test, the master microprocessor continues to perform the remaining tests with valid results.

NOTE If there are errors in the motion-object RAM, the motion-object parade displayed during the looping tests will probably look wrong.

EAROM PARITY Test The EAROM PARITY test checks the parity of the two areas in the EAROM memory that store the game options, These options ate important to the game play, so two sets of options and vertical parity checksums are stored in the EAROM. If either checksum is wrong, the screen displays the following message: EAROM PARITY ?? LOC 3}-K 3/-K is the location of the bad IC.

NOTE ?? means the EAROM may be bad. Unlike the RAM and PROM, there is no way to tell for certain that the EAROM is bad. This error is caused by either a bad IC of a failure of the EAROM writefenable circuitry. If replacing the EAROM does not fix the problem, the error is probably in the enable circuit. In this case you should call your Atari Field Service office for further help. If an error occurs during this test, the master microprocessor continues to perform the remaining tests with valid results.
Page 19

CLOAK & DAGGER

MASTER INTerrupt Test The MASTER [NTerrupt test checks to see if the master microprocessor is receiving interrupts every 4 ms. It also checks to see that the VBLANK line is active every 4 interrupts (every 16 ms). If either interrupt iest fails, the screen displays the following error message:

MASTER INT BAD

NOTE Ifthis error occurs, the master microprocessor continues through the rest of the tests, but the screens shown during the looping test may not be correct.

SLAVE COMmunications Test The SLAVE COMmunications test checks to see if the slave microprocessor can transfer a message from one area to another in the communications RAM. The master microprocessor then Verifies that the slave microprocessor performed that transfer correctly. The communications RAM is located between hexadecimal addresses 0800 and OFFF. If this test fails, the screen displays the following message: SLAVE COM BAD This error may mean one of two things:

  • The slave microprocessor is not operating, or
  • The interface circuitry that the siave microprocessor uses to talk with the communications RAM is not working. Check the LED mounted on the Slave PCB. If the LED is not flickering, the slave microprocessor is not operating, If the LED is flickering, the slave microprocessor is operating but the interface circuitry to the communications RAM is not working. If the SLAVE COM test passes, the master microprocessor waits for all the following test results from the slave microprocessor. If the slave fails to respond within a fixed time for each test, the results of the SLAVE COM test are changed from SLAVE COM MADE to SLAVE COM FAILED, and the rest of the slave tests (SLAVE RAM, SLAVE ROM, BITMAP RAM, SHARED RAM, and SLAVE INT tests) are skipped. The self-test routine goes straight to the looping, tests. SLAVE RAM Test The SLAVE RAM test is just like the MASTER RAM test described previously, except that the slave microprocessor memory (hexadecimal locations 0000-0F FF) is now tested.
Note that this includes the communications RAM, which has already been partially tested. Ifan error occurs during this test, the screen displays the following message showing the bad IC on the Slave PCB: SLAVE RAM BAD; LOC 1D ID is the location of the defective IC. Set Up

The slave microprocessor tries to perform the rest of the tests even ifan error occurs in the SLAVE RAM test. In case of error, do not trust the results of any remaining slave tests. If the master microprocessor does not receive the results of this test from the slave after about 2 seconds, it changes the results of the SLAVE COM test from SLAVE COM MADE to SLAVE COM FAILED and skips all remaining tests involving the slave microprocessor. SLAVE ROM Test

NOTE To properly run this test, toggle 3 ofthe option switch at location 5A on the Master PCB must be OFF.

The SLAVE ROM test computes the checksums for every slave program EPROMIC. Ifany checksum is not right for the IC under test, the screen displays the following message: SLAVE ROM BAD, LOCS: 1E-F;1F-H;1J;1K;1L;1M;1N 1E-F, 1F-H, Uf, 1K, 1L, 1M, and are the locations of all slave program memory devices. Only the bad slave memory devices are displayed.

NOTE Ifan error occurs during this test, the slave microprocessor continues to perform the remaining tests. The IC at location 1N contains the self-test program, If the IC at location 1N is defective, all remaining slave self-test results may be wrong.

SLAVE INTerrupt Test The SLAVE INTerrupt test checks if the slave microprocessor is receiving interrupts. If no interrupts are received within 2 seconds (they should occur every 16 ms), the screen displays the following error message: SLAVE INT BAD

NOTE The slave microprocessor continues to perform the rest of the tests even if this test fails, but the next test may not be valid.

If the master microprocessor does not receive the results of this test from the slave microprocessor after about 3 seconds, it changes the results of the SLAVE COM test from SLAVE COM MADE to SLAVE COM FAILED, The master microprocessor then skips the rest of the tests involving the slave microprocessor.

2-5

Page 20

Self Test

BITMAP RAM Test The slave microprocessor tests the bitmap RAM. The BIT. MAP RAM test takes about 8 seconds. During this test, the screen changes color three times—from brown to green to tan. Two separate bitmap buffers used by the slave microprocessor are each checked during this test. Ifan error occurs, the screen displays one of the following messages: BITMAP READ ERROR; BITn nis the bit between 7 and 3 that is normally tied to ground; but is detected at a high level during a reading of the bitmap. BITMAP BAD; LOC nnn nnnis the location of the first IC in which a read or write error is found by the slave microprocessor. Only the first bad IC location found is listed on the screen. nnn is one of the following IC locations on the slave PCB: © 7A through 7F ¢ 8A through 8F

  • 9A through OF
  • 10A through 10F If the master microprocessor does not receive the results of this test from the slave microprocessor after about 16 seconds, it changes the results of the SLAVE COM test from SLAVE COM MADE 0 SLAVE COM FAILED and skips all remaining tests involving the slave.

SHARED RAM Test Both microprocessors test the communications RAM at the same time. They check the clock-stretching and priority-access circuitry used by this RAM. This test is done only when four conditions are met:

  • The slave microprocessor is operating.
  • The master microprocessor is operating.
  • The slave microprocessor indicates that the shared communications RAM is good.
  • The master microprocessor indicates that the shared communications RAM is good. Ifan error is detected, the screen displays one or two of the following messages (depending on which microprocessor detects the error): SHARED RAM BAD; LOC 1D-F, M

SHARED RAM BAD; LOC ID-E, S

1D-E is the location of the communications RAM IC on the Master PCB.

NOTE If an error occurs here, it is not due to a faulty RAM IC; but is caused by the surrounding circuitry. CLOAK & DAGGER

S means the results came from the slave microprocessor on the Slave PCB. M means the results came from the master microprocessor on the Master PCB. Even if an error is detected, both microprocessors continue with the looping tests. If the master microprocessor still does not receive the results of this test from the slave within about 2 seconds, it will change the results of the SLAVE COM test from SLAVE COM MADE to SLAVE COM FAILED, LOOPING TESTS Once all of the main diagnostic tests are performed, the self-test routine continues to perform a series of tests until the self-test switch is turned off. These tests include the following: «Reading the joysticks ® Reading the switches and coin mechanisms

  • Reading the option switch block
  • Outputting all sounds and music e — Testing the start switches and LED ¢ = Moving all motion objects © Testing all possible bit-map store variations ¢ Changing the colors of a set of stamps positioned at each corner of the screen.
NOTE The stamps in each corner of the screen can be used to adjust both the horizontal and vertical size as well as the centering of the video display.

Looping Test Toggles The bit-map looping test starts and stops by pressing the IGNITER bution. The motion-object parade starts and stops with the 1-player start switch. This also causes the repeat playing of any current sound. The sounds start and stop by pressing the 2-player start switch. Note thatany sound in progress finishes before the sounds stop. An asterisk (*) appears next to the sound number to indicate that the sound has been turned off. Switches and Joysticks During the looping tests all switches and the two joysticks are tested continuously. They report the following three types of switch-input results to the screen:

  • OPT SWTCHS. The option switch is \ocated at position 5A on the Master PCB. Toggles 1 through 8 are set at the factory as follows (1 is on; 0 is off): Bits 1-6 = 0 BiL7 =1 Bit8 = 0
Page 21

CLOAK & DAGGER

  • PLA SWTCHS. The two start switches are read separately. These switches are as follows (from left to right): 1-player start 2-player start The remaining 6 bits are not used and can be either a 0 ora 1. Bits 1 and 2 are normally 0 and become 1 when the appropriate start switch is pressed (active high).
  • DIR SWTCHS.This row of digits represents the rest of the switches that are read directly through the hardware. These switches are as follows (from left to right): IGNITER switch (player 1) IGNITER switch (player 2—not used) COIN AUX switch (ADVANCE switch on coin door) COCKTAIL cabinet (not used) RIGHT COIN switch LEFT COIN switch SELF-TEST switch VBLANK The bit used for VBLANK sometimes flickers between states on the screen. It may show up as either a zero ora one (this is normal). The bit used for the self-test switch should always be zero (active low because the game is using its diagnostics). Test the start switches and each LED by pressing the switches and observing the corresponding LED. The LED is bad if the corresponding PLA SWTCHS bit on the screen toggles with the switch. The switch is bad if neither the LED nor the PLA SWTCHS bit on the screen changes. SELF-TEST MENU Once the looping tests begin, enter the self-test menu by turning off the self-test switch. The self-test menu now appears (see Figure 2-2), This menu allows more testing (using the color-bar test), allows the operator to review the game statistics, and allows the operator to modify the program option settings. The instructions on how to use this menu and any of the displays that it leads to are all contained within the game program and are displayed as appropriate. The EXIT function returns the game to normal game play. All of the other functions that may be selected from this menu return the user to this menu. To select one of the self-test menu functions, use the left joystick to position the blinking arrow next to the desired function. Press and hold down the IGNITER button. To return to normal game play, select the EXIT function. Set Up

SELF-TEST meNY

  • COLOR BAR TEST GAME OPTIONS STATISTICS Exit

HEE GS int Tea ti cONsTAbe”

Figure 2-2 Self-Test Menu Display

COLOR BAR TEST Selecting the COLOR BAR TEST displays a color bar showing the seven intensity levels for each color (see Figure 2-3). Red appears first. Press the IGNITER button to change colors. Pressing IGNITER repeatedly cycles through the three primary colors (red, green, and blue). Press either one of the player start switches to return to the self-test menu.

coLoR BAP TY

s * 3 my ub

Figure 2-3 Color Bar Test Display

2-7

Page 22

Self Test

OPTION MENU Function The OPTION MENU function should be viewed as part of ihe self-test procedure to ensure that the EAROM was correctly initialized (see Figure 2-4), The factory default game option settings are as follows: Possible Options STARTING LIVES: 3 35 GIVE EXTRA LIVES? YES YES/NO GIVE FREE GAMES? YES YES/NO DIFFICULTY FACTOR:B A—D A = easiest; D = hardest Use the left joystick to select the option you wish to change, then press IGNITER to choose the new option. The options now listed on the screen are the game operating options. To return to the self-test menu, press either the 1- or 2-player start button,

OFTLON menu

*® STARTING LIVES: @ GIVE EXTRA LIVES? VES vE FREE GAMES? VES DICFIEWULITY FACTOR: o

PRESS PLAVER START VO EXIT... MRE SRE. Bui FER PE CARNES EST

Figure 2-4 Option Menu Display

2-8 CLOAK & DAGGER

STATISTICS SUMMARY The STATISTICS SUMMARY function should be viewed as part of the self-test procedure to ensure that the EAROM ‘was cortectly initialized (see Figure 2-5). All statistics values should read 0 if the game has never been played. If one or more games have been played since power was first applied to the game, the statistics show how many games have been started and completed, the number of free games given, the average game time, and the longest game time. To exit this function, press either the 1- or 2-player Start button. To clear the statistics and high-score table, hold down the IGNITER button while pressing either the 1- or 2-player Start button.

NOTE The total number of games played is not reset to zero with the rest of the statistics. This statistic clears only the first time the game is powered up.

STATISTICS Summary TOTAL GAMES: SEs BABES Ange EVee.. 3 CBEBGSE GARE TIRE: © 9a

PRESS PLAVER START TO EXiT...

TO FGER erbGb°eraver SYART™

Figure 2-5 Statistics Summary Display

FINAL Start the game and listen to the musicas a final check. ONE low melody starts playing before a SECOND high melody begins to play. The two melodies play together. Be sure that BOTH melodies are present. (Each melody comes through a different sound IC and amplifier section.) This test checks both sets of sound channels.

Page 23

MMI

ao

anny \

Maintenance

The maintenance procedures provided in this chapter are for those items which are subject to the most severe use. To assure the maximum trouble-free operation from this game, Atari recommends that periodic routine maintenance be performed on the game components described in the following procedures. How often routine maintenance is performed depends upon the game environment and frequency of play.

WARNING To avoid possible electrical shock hazard, unplug the game prior to performing any maintenance.

Chapter 3

Page 24

Maintenance

Opening the Control Panel

Defender’ Cabinet

1.

2.

w Unlock and remove the rear access panel. Reach inside the game cabinet and release the two spring-draw latches on the sides of the cabinet to the rear of the control panel. Remove the #10 screws, securing the control panel to the cabinet, from the security brackets. From the front of the game, lift the control panel and. rest iton something approximately the same height as the cabinet. Joust’, Robotron: 2084’, and Stargate’ Cabinets

lL Unlock and remove the rear access panel.

  • Reach inside the game cabinet and release the two spring-draw latches on the right side of the hinged rear door.
  • Open the hinged rear door.
  • Reach inside the game cabinet and release the two spring-draw latches on the sides of the cabinet to the rear of the control panel.
  • Remove the #10 screws, securing the control panel to the cabinet, from the security brackets.
  • From the front of the game cabinet, lift the control panel at the top edge and tilt it toward you.

: ;

Removing the Joystick Assembly

Reassembling the Joystick Assembly

Perform the following procedure to remove the joystick assembly from the control panel. L

2,

3.

rs Open the control panel as previously described. Disconnect the joystick harness wires. Use a %-inch hex nutdiiver to remove the hardware that mounts the joysticks to the control panel. Remove the joysticks from the control panel.

Disassembling the Joystick Assembly

Perform the following procedure to disassemble the joystick assembly (see Figure 3-1).

7Trademarks of Williams Electronics, Inc.

3-2 CLOAK & DAGGER

Remove the four screws in the plastic joystick frame.

NOTE The joystick is a spring-loaded control. Be carefui not to lose the switch actuator and spring as you remove the retaining ting in the next step.

Remove the retaining ring from the bottom of the shaft. The assembly will now come apart. To remove the beilows, pry it up and out of the plastic frame,

Perform the following procedure to reassemble the joystick assembly (see Figure 3-1),

10. Holding the control knob in one hand with the shaft pointing up, slide the large plastic washer onto the shaft. Slide the flat side of the top plate on top of the plastic washer. Slide the nylon washer onto the shaft over the top plate. Slide the bellows on the shaft over the washer. Note that the inner raised ring on the bellows is longer on one side. This side goes next to the washer (toward the control knob). Position the four screw holes in the bellows over the screw holes in the top plate. Slide the steel washer onto the shaft to rest on the bellows. Slide the spring on top of the washer. Slide the switch plate on top of the spring, positioning the four screw holes over those in the top plate. Use a Phillips-head screwdriver to install the four screws that hold the switch plate and top plate together. Slide the nylon switch actuator onto the shaft over the switch plate. Note that the smaller recessed end of the switch actuator fits down on the spring. The switch actuator must be pressed down on the spring and heid under pressure while you secure the retaining ring.

Page 25

CLOAK & DAGGER Maintenance

‘Switch Actuator

i,

— Switch Plate

Guard/Actuator

Leaf Switch

Bellows

Nylon Washer

—— Top Plate

Washer

Figure 3-1 8-Position Joystick Assembly

3-3

Page 26

Maintenance

Removing the Joystick

Leaf Switches

Perform the following procedure to remove the joystick leaf switches from the 8-position joystick assembly (see Figure 3-1).

  • Toremove the joystick leaf switches, you do not need to disassemble the joystick. Disconnect the snap-on wire connectors to each leaf switch and, using your thumbs, pry apart the plastic flanges on the switch holder, With your index finger, lift the switch up so that it will clear the plastic tab located on the outside end of the switch holder. Slide the leaf switch out of its holder. Replace the switch in reverse order.

Adjusting the Joystick

Perform the following procedure to adjust the joystick leaf switches on the 8-position joystick assembly,

  • Make sure that each ieaf switch is firmly seated in its holdci. There is a small gray plastic tab on the outside end of the switch holder. The black plastic partofeach leaf switch must be in front of this tab. The plastic guard/actuater must be on the side of the switch toward the switch actuator.
  • Check that all four leaf switches can be activated by watching the switch blades as you move the joystick. handle up, down, left, and right.
  • Test the four diagonai positions, In each diagonal posi- Gon, two leaf switches should close. Switches should continue bending slightly after making contact.
  • Adjust each switch contact for a narrow gap using the following procedure: a. Push the joystick handle away from the switch for easier servicing. b. Usea pair of needlenose pliers or a switch adjustment tool to bend each double set of blades in toward the center. Make the bend where the double set of blades protrude from the black piastic part of the switch,
  • Recheck the switch action. The switches must move independently for right, left, up, down, and diagonal motion of the joystick. CLOAK & DAGGER

Pushbutton Leaf Switch

Perform the following procedure to adjust the pushbutton teaf switch on the control panel.

  • With the control panel open, adjust the leaf switch contacts for a narrow gap. When the pushbutton is depressed, the resulting wiping action of the cross-bar contacts provides a self-cleaning feature. Don't burnish the contacts. To clean them, use electrical contact cleaner. To replace the leaf switch, remove the screw with a Phillips-head screwdriver. nw
  • To replace the switch pushbution, turn the stamped nut witha wrench ina counterclockwise direction, as seen from the inside of the control panel. The ring on the outside of the control panel should not spin.
  • Reinstall the pushbutton switch. Reconnect the harness wires to the switch terminals.

Start Switches

Perform the following procedure to adjust the start switches on the control panel.

NOTE Start switches can be checked for proper operation with an ohrameter. Disconnect the wires from the switch terminals and connect an ohmmeter between the normally open and common contacts. Press and release the pushbutton and check for zero and infinite resistance. If the switch is not operating properly, perform the following procedure.
  • Turn the switch counterclockwise while firmly holding the black cone-shaped bushing on the outside of the control panel Install a new switch using the reverse procedure. i)
  • Reconnect the harness wires as shown in Figure 3-2. Make certain the right colors go to the right tabs on the switch,
Page 27

CLOAK & DAGGER Maintenance

Black ‘Common fo Red (+) JL Greytwhite Normally Open Let Red/White, Shack WioteuwWhite Black Orange/White, Black

Black ‘Common

r= Red (+) Blue/White, Black ist\ Normally Open Start2 White/Black

Joystick Leaf Switches Start Switches

Figure 3-2 Wire Connections to the Control Panel

3-5

Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

Illustrated Parts Lists

This chapter provides information you need to order parts for your game, Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, a parts list is included for the hardware to mount the printed-circuit boards (PCB) to the cabinet. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the resuits will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual. a = TUTTI TTT TT iS

Chapter 4

Page 30

iustraied Parts Lists CLOAK & DAGGER

L ———— o41474.01 Attraction Shield

041473-01 Control Panel Assy Display Shield Not Shown See Figure 4-3

Manual, Schematics, & Self-Test Chart— See following parts list

Figure 4-1 CLOAK & DAGGER Retrofit Kit Contents for Defender A041462-01 A

4-2

Page 31

CLOAK & DAGGER Illustrated Parts Lists

119006-103 Volume Control

A041509-01 Main Harness Assy oaser2.02

Wood Mounting Panel

EMI Shield & Dual PCB Assy See Figure 4-6 EMI Cage Assy See Figure 4-5

Figure 4-1 CLOAK & DAGGER Retrofit Kit Contents for Defender, continued A041462-01 A

Page 32

Illustrated Parts Lists CLOAK & DAGGER

CLOAK & DAGGER Retrofit Kit Contents for Defender Parts List

Part No. Description

A037701-01 Electromagnetic Interference (EMI) Cage and Guides Assembly—includes 037700-02 EMI Cage 178047-032 PCB Guide

A040733-01 EMI Shield and Dual PCB Assembly—includes A039431-02 CLOAK & DAGGER Interconnect PCB (not shown—located in EMI Cage)

A039938-21CLOAK & DAGGER Slave PCB(not shown—-located in EMI Cage)
A039942-21CLOAK & DAGGER Master PCB(not shown—located on EMI Cage)

A040404-01 EMI Shield PCB (not shown—located in EMI Cage)

A041463-01 Control Panel Assembly—includes A041465-01 Conuol Panel and Decal Assembly A040729-01 Control Harness Assembly 171021-001 8-Position Joystick Assembly A041509-01 Retrofit Main Harness and Component Assembly—includes A041402-01 Main Harness

119006-10310 kQ Dual Potentiometer(Volume Control)

SP-242 CLOAK & DAGGER Schematic Package ST-242-01 CLOAK & DAGGER Chart with SelfTest Procedure and Option Switch Settings TM-242 CLOAK & DAGGER Operators Manual

72-1816F #832 x lnch Long Cross-Recessed Pan-Head Machine Screw (used to mount wood panel to cabinet wali—not shown) 75-0185, #8 Flat Washer (used to mount wood panel to cabinet wall—not shown)

75-0488#8 SplitLock Washer(used to mount wood panel to cabinet wall—not shown)
038086-01Shock Warning Label(not shown)

038158-03 Product iD Label (noishown)

039450-01FCC Compliance Label(not shown)
041471-01Left Side-Panel Decal(not shown)
041471-02Right Side-Panel Decal(not shown)
041472-01Coin-Mechanism Panel Decal(not shown)

041473-01 Display Shield 041474-01 Attraction Shield.

041476-01Attraction Shield Semi-Rigid Film(not shown—located behind attraction shield)

04147702 Wood Mounting Panel for EMI Cage Assembly

175004-708,#8 Flat Fiber Washer(used to mount EMI cage to wood panel—-not shown)

176015-112 #10 x 34-Inch Long Cross-Recessed Pan-Head Screw (one used to mount EMI cage to wood panel; two used on control panel—not shown)

4-4

Page 33

CLOAK & DAGGER Mlustrated Parts Lists

041474-01 Attraction Shield

041473-01 Display Shield

Control Panel Assy See Figure 4-3

Figure 4-2. CLOAK & DAGGER Retrofit Kit Contents for Joust, Robotron: 2084, and Stargate A041462-02 A

4-5

Page 34

Illustrated Parts Lists CLOAK & DAGGER

Manual, Schematics, & Self-Test Chart— See following parts list

119006-103 Volume Control A041511-01 Main Harness Assy

EM! Shield & Dual PCB Assy See Figure 4-6

041477-02 Wood Mounting Panel

EMI Cage Assy

See Figure 4-5

Figure 4-2 CLOAK & DAGGER Retrofit Kit Contents for Joust, Robotron: 2084, and Stargate, continued A041462-02 A

4-6

Page 35

CLOAK & DAGGER Ihustrated Parts Lists

CLOAK & DAGGER Retrofit Kit Contents for Joust, Robotron: 2084, and Stargate Parts List

Part No. Description

A037701-01 Electromagnetic interference (EMI) Cage and Guides Assembly—includes 037700-02 EMI Cage 178047-032 PCB Guide

A040733-01 EMI Shield and Dual PCB Assembly—includes A039431-02 CLOAK & DAGGER Interconnect PCB (not shown—located in EMI Cage)

A039938-21CLOAK & DAGGER Slave PCB(not shown—located in EMI Cage)
A039942-21CLOAK & DAGGER Master PCB(not shown—located in EMI Cage)

A040404-01 EMI Shield PCB (not shown——located in EMI Cage) A041464-01 Contro} Panel Assembly-—-includes A041465-01 Control Panel and Decal Assembly A040729-01 Control Harness Assembly 171021-001 8-Position Joystick Assembly

AQ41511-01 Retrofit Main Harness and Component Assembly—includes A041510-01 Main Harness 119006103 10 kM Dual Potentiometer (Volume Gontrol)

SP-242 CLOAK & DAGGER Schematic Package SF242-01 CLOAK & DAGGER Chart with Self-Test Procedure and Option Switch Settings TM-242 CLOAK & DAGGER Operators Manual

72-181GF #8-32 x 1-Inch Long Cross-Recessed Pan-Head Machine Screw (used to mount wood panel to cabinet wali—not shown) 75-0188 #8 Flat Washer (used to mount wood pane! to cabinet wall— not shown)

75-0488#8 Split-Lock Washer(used to mount wood panel to cabinet wall—not shown)
038086-01Shock Warning Label(not shown)

038158-03 Product ID Label (not shown)

039450-01FCC Compliance Label(not shown)
041471-01Left Side-Panel Decal(not shown)
041471-02Right Side-Panel Decal(not shown)

041473-01 Display Shield 041474-01 Atiraction Shield

04147601Attraction Shield Semi-Rigid Film(not shown—located behind attraction shield)

04147702 Wood Mounting Panel for EMI Cage Assembly

175004-708,#8 Flat Fiber Washer(used to mount EMI cage to wood panel—not shown)

176015-U12 #10 x 34-Inch Long Cross-Recessed Pan-Head Screw (used to mount EMI cage to wood panel—not shown)

Page 36

IHustrated Parts Lists CLOAK & DAGGER

178030-004 Red Pushbutton 471021-001 Joystick Assy. See Figure 4-4 78-6900402 62-039 Foam Tape LED Switches +-Player Start 2-Player Start 177010-240 Locknut

75-5112B Bolt 75-9910NO Nut

= | 036895-01 2 Z| Switch Bezel

A040729-01 Harness 160013-001 Leaf Switch & Button Holder

A041465-01 A041466-01 Control Panel w/Decal Control Panel w/Decal (Defender) (Joust, Star, Robotron) 041467-01 041468-01 Control Panel Control Panel (Defender) (Joust, Star, Robotron) Players may receive an electrical shock if this control panelis not properly grounded! After servicing any parts on the panel, make sure that the ground strap is making contact with the control panel.

Figure 4-3 Control Panel Assembly Defender Cabinet A041463-01 A Joust, Robotron: 2084, and Stargate Cabinets A041464-01 A

Page 37

CLOAK & DAGGER illustrated Parts Lists

Control Panel Assembly Parts List

Part No. Description

Defender Cabinet A041465-01 Conirol Panel with Decal 041467-01 Control Panel Joust, Robotron: 2084, Stargate Cabinets 4041466-01 Control Panel with Decal 041468-01 Control Panel AN Cabinets A041729-01 Control Panel Harness Assembly 62-039 SPDT Momentary Pushbutton Start Switch with Red Light- Emitting Diode 75-SU2B #10-24 Black Carriage Bolt 75-9910NO #%, x VW Stamped Nuc

78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x %-Inch Thick (24 inches required) 036895-01 Black Molded Switch Bezel 040489-03 Control Panel Decal (not shown) 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 171021-001 8-Position Joystick Assembly 177010-240 #10-24 Hex Locknut 178030-004 Red Pushbutton Assembly 179125-001 Grounding Terminal (not shown)

Page 38

Illustrated Parts Lists

4-10 CLOAK & DAGGER

Washer

'99-080036 Top Plate

99-080029 Nylon Washer

99-080031 Bellows

99-080032 Steel Washer

Leat Switch

99-080033, A Guard/Actuator

99-080037 Switch Plate

82-AL616 99-080038 Screw I Switch Actuator

73-3003, an ay Faainns Ring Figure 4-4 8-Position Joystick Assembly 171021-001 A

Page 39

CLOAK & DAGGER

8-Position Joystick Assembly Ulustrated Parts Lists

Parts List

Part No, Description

73-3003 Retaining Ring 82-AL616 #6 x I-Inch Cross-Recessed Pan-Head Type BT Tapping Steel Screw 99-080025 Leaf Switch 99-080026 2-Inch Black Plastic Washer 99-080028 Metal Shaft 99-080029 Nylon Washer 99-080030 Spring 99-080031 Bellows 99-080032 Flat Steel Washer 99-080033 Plastic Guard/Actuator 99-080036 ‘Top Plate 99-080037 Switch Mounting Plate 99-080038 Nylon Switch Actuator

41h

Page 40

Illustrated Parts Lists CLOAK & DAGGER

NOTE Within the United States the Federal Communications Commission requires that the game printed-circuit boards be housed in the Electromagnetic Interference Cage with the Electromagnetic Interference Shield Printed-Circuit Board attached.

A037701-01 EMI Cage with Guides A037701-01 EMI Cage

Guide

72-1404F Screw EMI Shield PCB A039938-21 See Figure 4-6 CLOAK & DAGGER 037873-02 soon Slave PCB ‘Spacer See Figure 4-8 178045-442 Fastener 175009-221 Washer 72-1404F Screw 034536-03 Foam Pad

Grounding clip not shown

72-1604F Screw

A039431-01 A039942-21 Interconnect PCB oates6-08 CLOAK & DAGGER Foam Pad See Figure 4-7

Figure 4-5 Electromagnetic Interference (EMI) Cage Assemblies and PCB Mounting Hardware

4-12

Page 41

CLOAK & DAGGER Iltustrated Parts Lists

EMI Cage Assemblies and PCB Mounting Hardware Parts List

Part No. Description A037701-01 EMI Cage (includes guides) A039431-01 Interconnect PCB A039938-21 CLOAK & DAGGER Slave PCB A039942-21 CLOAK & DAGGER Master PCB A040404-01 EMI Shield PCB-includes 72-1404F #4-40 x ¥4-Inch Cross-Recessed Steel Screw 037873-02 Spacer 175009-221 Plastic Washer 178044-242 Grommet 178045-442 Snap-In Fastener 72-1604F #6-36 x 4-Inch Cross-Recessed Pan-Head Screw 034536-02 0.50-Inch Thick Foam Pad (located between Master and Slave PCB) 034536-03 1.12-Inch Thick Foam Pad (located on Interconnect PCB) 175004-708 #8 Flat Fiber Washer 176015-112 #10 x %4-Inch Cross-Recessed Pan-Head Screw 179125-001 Grounding Clip (not shown)

Page 42

Illustrated Parts Lists CLOAK & DAGGER

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING ‘CONFIDENTIAL: Reproduction forblden without the specific wit ten permission of Atari, Inc, Sunnyvale, CA. This drawing is only conditionally issued, and nether receiptnor possession thareotconfers or transters any rightin, or license fo use, the subject mstter of the drawing ot any design or technical information shown thereon, ‘nor any right to reproduce this drawing or ary part thereot. Except formmanufacture by vendors of Alri Inc., and for manulacture unde: the corporation's writen license, no rightis granted to reproduce this, ‘drawing or thesubject mater thereof, unless by watlen agreement vith or written permission from the corporation,

HT UELP EET PETRY HELEET TEETER

ROROeReeneen

Figure 4-6 EMI Shield PCB Assembly A040404-01 A

Page 43

CLOAK & DAGGER ‘ilustrated Parts Lists

EMI Shield PCB Assembly Parts List

DesignatorDescriptionPart No.

Capacitors

Cl-C5O.1 pE, +80%, -20%, 50 V Ceramic Capacitor122002-104
CO-C160.01 wF, +80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103
C21O.1 BE, +80%, -20%, 50 V Ceramic Capacitor122002-104
C24, C250.01 pF, +80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103
C27-C350.01 pF, +80%, 20%, 25 V Minimum, Axial-iead Ceramic Capacitor422005-103
C37-C410.1 wE +80%, -20%, 50 V Ceramic Capacitor122002-104
C440.1 4B +80%, -20%, 50 V Ceramic Capacitor122002104
C49-C530.01 uF, + 80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103
C54-C56O.1 pF, +80%, -20%, 50 V Ceramic Capacitor122002104
C57, C580.01 EF, + 80%, -20%, 25 V Minimum, Axial-Lead Ceramic Capacitor122005-103
C60~C620.1 wR +80%, -20%, 50 V Ceramic Capacitor122002-104
C63-C65470 pF, 100 V Ceramic Capacitor(Acceptable substitute is part no.122013-471)422016-471
C660.01 pk, +80% ,-20%, 25 V Minimum, Axial-lead Ceramic Capacitor122005-103
C671000 pk,+5%, 100 V Axial-Lead Ceramic Capacitor122016102
C680.01 wF, +80%, -20%, 25 V Minirnum, Axial-Lead Ceramic Capacitor122005-103,
C69, C701000 pF, + 5%, 100 V Axial-Lead Ceramic Capacitor122016-102

Connectors

P18, PID24-Pin Connector(Acceptable substitute is part no. 179041.024)179073-024
P2044-Pin Connector(Acceptable substitute is part no, 179046-044)179073-044

Miscellaneous Spacer 037873-02 #4-40 x -Inch Cross-Recessed Pan-Head Steel Machine Screw 72-1404F Plastic Washer 175009-221 Grommet 178044-242 Snap-In Fastener 178045-442

Page 44

Illustrated Parts Lists

4-16 CLOAK & DAGGER

10° org ]

  • c= 0s — = cw —

a } my 1 ] ong, ]

oN

  • —I — exe ] oe _]

“IATL I oe

Figure 4-7 CLOAK & DAGGER Master PCB Assembly A039942-21 A

Page 45

CLOAK & DAGGER Illustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden wihoutthe speciti wt Jen permission of Atari, Ine, Sunnyvale, CA. This drawing is only ‘conditionally ssued, and nether receipinor possessionthereof.confers ortransfers any rightin, orlicense to use, the subject mater of the draningor ary design cr technical information shown thereon, nor any ight 19 reproduce this drawing or ary partthereot. Except for manufacture by vendors of Atari, Inc. and formartufacture under the corporations writer icense, na rights granted!to reproduce this drawing or thesubject matter thereof, uniess by writen agreement with of written permission ‘rom ihe corporation

Figure 4-7 CLOAK & DAGGER Master PCB Assembly, continued A039942-21 A

Page 46

Illustrated Parts Lists

CLOAK & DAGGER Master PCB Assembly CLOAK & DAGGER

Parts List

DesignatorDescriptionPart No.

Capacitors

cLc90.1 pF, +80% -20%, 50 V, Ceramic Capacitor122002-104
C300.01 yF, 100 V, Radial-Lead Mylar Capacitor21-101103,
C310.047 nF, 100 V, Radial-Lead Mylar Capacitor21-101473
C33,0.022 pF, 100 V, Radial-Lead Mylar Capacitor21101223
C3510 pE, 25 V, Axial-Lead Aluminum Electrolytic Capacitor(Acceptable substitute24-250106

is part no. 24-350106)

C36-C380.1 uF, +10%, 25 V, Ceramic Capacitor122002-104
C396.01 pF, 100 V, Radial-Lead Mylar Capacitor21-101103,
C400.022 F, 100 V, Radial-Lead Mylar Capacitor21-101223,
CA20.022 E, 100 V, Radial-Lead Mylar Capacitor21101223
C441.0 pE, 50 V, Axial-Lead Aluminum Electrolytic Capacitor24-500105
C4510 zF, 25 V, Axial-Lead Aluminum Electrolytic Capacitor(Acceptable substitute24-250106

is part no, 24-350106)

C46100 pF, 25 V, Axial-Lead Aluminum Electrolytic Capacitor24-250107
C470.1 pF, +10%, 25 V, Ceramic Capacitor122002-104
C51-C530.001 “FE, 100 V, Radial-Lead Mylar Capacitor21-101102
54, C5510 pF, 25 V, Axial-Lead Aluminum Electrolytic Capacitor(Acceptable substitute24-250106

is part no. 24-350106)

C56, C57100 pF, 35 V, Axial-Lead Aluminum Electrolytic Capacitor(Acceptable substitute-24- 350107

is part no. 124001-107)

C600.1 uF, +10%, 25 V, Ceraraie Capacitor122002-104
C64-C66100 pé, 100 V Minimum, Dipped Fixed Mica Capacitor128002-101
C67-C1090.1 pF,10%, 25 V, Ceramic Capacitori22002-104
cll, C20.1 pF, +10%, 25 V, Ceramic Capacitor122002-104
Cll,100 F, 25 V, Axial-Lead Aluminum Electrolytic Capacitor24-250107
C14, ClIS1.0 uF, 50 V, Axial-Lead Aluminum Electrolytic Capacitor24-500105,
Cu6é0.1 wE, +10%, 25 V, Ceramic Capacitor122002-104

Coil

LI-L41.0 zH, 830 mA, 29 Q, +10% Peaking Coil Inductor141007-001

Diodes

CRI-CRIO100 V Switching Diode3LIN914
CRILRed Light Emitting Diode38-MV5053

Integrated Circuits

1AType-74LS157 Quad Data Selector/Multiplexer Integrated Circuit37-7ALSIS?
1BType-74LS157 Quad Data Selector/Multiplexer Integrated Circuit37-74LS157
1CType-74LS157 Quad Data Selector/Multiplexer Integrated Circuit37-74L5157
IDE‘Type-74LS245 200 ns Tri-State Static RAM Integrated Circuit137211-120
IFType-74LS245 Tri-State Octal Bus Transceiver Integrated Circuit37-74L8245,
1HType-74LS245 Tri-State Octal Bus Transceiver Integrated Circuit37-74L8245,
yType-74LS139 Dual 2-4 Decoder/Multiplexer Integrated Circuit37-74LS139
ILType-74L827 Triple 3-Input NOR Gate Integrated Circuit37-TALS27
IMType-74LS86 Quad 2-Input EXOR Gate Integrated Circuit37-74LS86
1p‘Type-7418244 Line Driver/Receiver Integrated Circuit37-7ALS244
IR‘Type-7415244 Line Driver/Receiver Integrated Circuit37-7ALS244
2B‘Type-7418244 Line Driver/Receiver Integrated Circuit37-74LS244

(continued on next page)

Page 47

CLOAK & DAGGER

CLOAK & DAGGER Master PCB Assembly Illustrated Parts Lists

Parts List, continued

DesignatorDescriptionPart No.
2c‘Type-741824 Line Driver/Receiver Integrated Circuit3 7-7418244
2DEPROM Integrated Circuit136023-301
2FEPROM Integrated Circuit136023-302
2HyEPROM Integrated Circuit136023-303
2KEPROM Integrated Circuit136023-304
2L/MVertical Scroll Integrated Circuit3732141
3c‘Type-6502B 8-Bit Microprocessor Integrated Circuit90-6012
3E/F‘Type-7418245 Tri-State Octal Bus Transceiver Integrated Circuit37-7H8245
3HType-74L8245 Tri-State Octal Bus Transceiver Integrated Circuit377418245
3yKEPROM Integrated Circuit137329-450
3L“type-74L5157 Quad Data Selector/Multiplexer Integrated Circuit37-74L8157
3MType-74L8157 Quad Data Selector/Muhtiplexer Integrated Circuit377418157
3N‘Type-74LS157 Quad Data Selector/Multiplexer Integrated CircuitBT-TALSIS7
3P‘Type-741S194 Shift Register Integrated Circuit37-7ALS194
3R‘Type-7418194 Shift Register Integrated Circuit37-74L S194
4/SE‘Type-74L504 Hex Inverier Integrated Circuit37-7ALSO4
4i5F‘Type-74LS00 Quad 2-Input NAND Gate Integrated Circuit37-T74L800
4/SH‘Type-74L8245 Tri-State Octal Bus ‘Transceiver integrated Circuit3E74LS245,
4‘Type-74L808 Quad 2-Input AND Gate Integrated Circuit37-74L808
4KType-74S273 Octal D'lype Flip-Flop Integrated Circuit3 7-74LS273
4LiM200 ns Tri-State Static RAM Integrated Circuit137211420
4N‘Type-74LS157 Quad Data Selector/Multiplexer Integrated Circuit377418157
4pType-74L8194 Shift Register Integrated Circhit37-74LS194
4R‘Type-74L8194 Shift Register Integrated Circuit37-74LS194,
5BCustom Integrated CiecuitC012294-01
5ciDCustom Integrated CircuitC012294-01
SE‘Type-74L804 Hex Inverter Integrated Circuit37741804
SE‘Type-741S138 Integrated Circuit37-74LSB8
SF‘Type-74L832 Quad 2-Input OR Gate Integrated Circuit37-TALS32
Sil‘Type-7418245 TH-State Octal Bus ‘Transceiver Integrated Circuit377418245
5]‘Type-74LS20 Dual 4-Input NAND Gate Integrated Circuit37-74LS20
5K‘Type-74L883 4-Bit Bin Full Adder Integrated Circuit37-74L883
SL‘Type-74LS157 Quad Data Selector/Multiplexer Integracd Circuit37-7ALS157
5M“Type-74LS157 Quad Data Selector/Multiplexer Integrated Circ: it37-74LS157
SNEPROM Integrated Circuit136023-306
5REPROM Integrated Circuit136023-305,
6D‘Type-741$393 Dual 4-Bit Bin Counter Integrated Circuit37-7418393
OEType-74LS32 Quad 2-Input OR Gate Integrated Circuit37-741832
OF‘type-74L874 Dual D-lype Flip-Flop Integrated Ciscuit37-7ALSTA
OHType-74LS174 Hex D‘Iype Flip-Flop Integrated Circuit37-7ALSI74
g“Type-7aL$83 4-Bit Bin Full Adder Integrated Circuit37-7ALS83
6K‘Type-741S275 Octal D‘Type Flip-Flop integrated Circuit37-4827
OL250 ns Tri-State Static RAM Integrated Circuit137250-001
6M250 ns Tri-State Static RAM Integrated Circuit137250-001
ON“‘Type-741832 Quad 2-Input OR Gate integrated Circuit37-74L932
6P‘Type-74LS194 Shift Register Integrated Circuit37-7ALSI94-
OR‘Type-74LS194 Shift Register Integrated Circuit37-TALSIO4
7‘Type-741S14 Hex Inverter SchmittTtigger Integrated Circuit37741814

(continued on next page)

Page 48

Illustrated Parts Lists CLOAK & DAGGER

CLOAK & DAGGER Master PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
7B‘Type-74LS74 Dual D-lype Flip-Flop Integrated Circuit37-74LS74
7C‘Type-74LS00 Quad 2-Input NAND Gate Integrated Circuit37-74LS00
7DType-74LS08 Quad 2-Input AND Gate Integrated Circuit37-74LS08
TE‘Type-741874 Dual D-Type Flip-Flop Integrated Circuit37-74LS74
TF‘Type-74LS74 Dual D-lype Flip-Flop Integrated Circuit37-7ALST4
7H‘Type-74LS244 Line Driver/Receiver Integrated Circuit37-7418244
walType-741S163A 4-Bit Synchronous Counter Integrated Circuit37-74LS163A
7KType-74LS163A 4-Bit Synchronous Counter Integrated Circuit37-7ALSIO3A
7LType-74LS163A 4-Bit Synchronous Counter Integrated Circuit37-TALSIOZA
™MType-74LSI63A 4-Bit Synchronous Counter Integrated Circuit37-7ALSIOZA,
7N‘Type-74LS157 Quad Data Selector/Multiplexer Integrated Circuit37-7ALS157
7P‘Type-74LS194 Shift Register Integrated Circuit37-TALS194
7R‘Type-74LS194 Shift Register Integrated Circuit37-7ALSI94
BA‘Type-74LS74 Dual D-lype Flip-Flop Integrated Circuit37-7A4LS7A
8BType-74LS32 Quad 2-Input OR Gate Integrated Circuit37-74L832
8C‘Type-74S04 Hex Inverter Integrated Circuit37-74804
8D‘Type-74LS32 Quad 2-Input OR Gate Integrated Circuit37-7ALS32
8EType-74LS00 Quad 2-Input NAND Gate Integrated Circuit37-74LS00
8FType-741S139 Dual 2-4 Decoder/Multiplexer Integrated Circuit37-7ALS139
8H‘Type-74L8273 Octal D-Type Flip-Flop integrated Circuit37-7ALS273,
8)‘Type-93422 45 ns ‘Tri-State Bipolar Static RAM Integrated Circuit(Acceptable137178-002

substitute is part no. 137178-001)

8K‘Type-74LS157 Quad Data Selector/Multiplexer Integrated Circuit37-7ALSIS7
8L.‘Type-93422 45 ns Tri-State Bipolar Static RAM Integrated Circuit137178-002
8M‘Type-74LS157 Quad Data Selector/Multiplexer Integrated Circuit37-7A1S157
8NEPROM Integrated Circuit136023-307
8REPROM Integrated Circuit136023-308,
9A‘ype-74LSI09A Integrated Circuit37-7TALSIO9A
OBType-74LS02 Quad 2-Input NOR Gate Integrated Circuit37-74LS02
9c‘Type-74LS20 Dual 4-Input NAND Gate Integrated Circuit37-74LS20
9D‘Type-741874 Dual D-Iype Flip-Flop Integrated Circuit37-7ALS74
9E‘Type-74LS139 Dual 2-4 Decoder/Multiplexer Integrated Circuit37-74L8139
OF‘Type-74LS08 Quad 2-Input AND Gate Integrated Circuit37-74LS08
9H‘Type-74S157 Quad Data Selector/Multiplexer Integrated Circuit37748157
oy‘Type-74LS273 Octal D‘Type Flip-Flop Integrated Circuit37-7ALS273
OK‘Type-748260 Dual 5-Input NOR Gate Integrated Circuit37-74S260
9OLIMOpen Collector Bipolar RAM Integrated Circuit137322-001
ON‘Type-74LS244 Line Driver/Receiver Integrated Circuit37-74LS244
ORType-74L8244 Line Driver/Receiver Integrated Circuit37-TALS244
10A‘Type-7407 Hex Buffer/Driver Integrated Circuit37-7407
10B‘Type-74LS259 8-Bit Latch Integrated Circuit37-74LS259
10C‘Type-74LS00 Quad 2-Input NAND Gate Integrated Circuit37-74LS00
10D‘Type-741S00 Quad 2-Input NAND Gate Integrated Circuit37-7ALSO0
10E‘Type-74LS04 Hex Inverter Integrated Circuit37-7ALSO4
10FType-741$86 Quad 2-Input Exclusive OR Gate Integzated Circuit37-7ALS86
10H‘Type-74LS153 4 to 1 Data Selector/Multiplexer Integrated Circuit37-7ALSIS3
10)Type-7418153 4 to 1 Data Selector/Multiplexer Integrated Circuit37-7ALSI53,
10KType-74LS174 Hex D-Type Flip-Flop Integrated Circuit37-7ALSI74

4-20 (continued on next page)

Page 49

CLOAK & DAGGER Ulustrated Parts Lists

CLOAK & DAGGER Master PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
10L“‘Type-74LS174 Hex D-Iype Flip-Flop integrated Circuit37-74LS174
uc‘Wype-74L874 Dual Dlype Flip-Flop Integrated Circuit37741874
wD‘Type-74L808 Quad 2-Input AND Gate Integrated Circuit37-741808
IF‘Type-741874 Dual D-Type Flip-Fiop Integrated Circuit37-74LS74
MHType-741S139 Dual 2-4 Decoder/Muhtiplexer Integrated Circuit37-74LS139
iy‘Type-741.S157 Quad Data Seiector/Multiplexer Integrated Circuit-FALSIS7
2BType-LM324 Quad Op-Amp Integrated Circuit37-LM324
13B512-Element Analog Delay Line Integrated Circuit.137310-001
BOD‘Type-LM324 Quad Op-Amp Integrated Circuit7-LM324
ByTypeTL082 Dual Operational Amplifier Integrated Circuit37TLOB2CP

Resistors

R110 kQ, +5%, Y% W Resistor110000-103
R268 kQ, +5%, 4 W Resistor110000-683
R32200, +5%, % W Resistor0000-221
R422 kQ, +5%, ‘A W Resistor110000-223,
RS1kQ, +5%, 4 W Resistor110000-102
R6-R810kQ, 25%, 4 W Resistor110000-103,
RO-RIG2200, +5%, '4 W Resistor0000-221
RI7-R24330.2, +5%, 4 W Resistor110000-331
R25-R282200, +5%, %& W Resistor119000-221
R29-R32330, +5%, % W Resistor0000-331
R33, R3410 kM, +5%, %& W Resistor0000-103
R35-R4l470, +5%, Y% W Resistor110000-471
R42-R481k@, £5%, 4 W Resistor110000-102
R65-R72470%, +5%, % W Resistori10000-471
R73-R891kQ, +5%, 4 W Resistor110000-102
RO2-R941kQ, +5%, % W Resistor1419000-102
ROS,2.2k, +5%, 4 W Resistor110000-222
ROG4.7kQ, 25%, 4 W Resistor110000-472
ROT10 kQ, £5%, 4 W Resistor110000-103,
R98, ROD100.2, 45%, 4 W Resistor110000-101
RiOO-R1021kQ, 25%, % W Resistor110000-102
R1032,2 kQ, 45%, %& W Resistor1310000-222
R1044.7, +5%, 4 W Resistor0000-472
RIOS10 kQ, 45%, 4 W Resistor110000-103
R106, R107100 2, +5%, “ W Resistor110000-101
R108-RUO1kQ, +5%, % W Resistor110000-102
Rit2.2kQ, +5%, 4 W Resistor§10000-222
RU24.7 kQ, 45%, 4 W Resistor110000-472
Rul31OkQ, 5%, % W Resistor0000-103
R14, RilS100.2, 45%, 4 W Resistor110000-101
R161k@, +5%, 4 W Resistori10000-102
Ri71OkQ, +5%, 4 W Resistor110000-103,
RUS18 kQ, +5%, 4 W Resistor110000-180
RUD100kQ, +5%, 4 W Resistor110000-104
R1IZ0-R1231kQ, 45%, %’ W Resistor110000-102
Ri24-R127A70Q, +5%, & W Resistor110000-471

(continued on next page)

Page 50

Ilustrated Paris Lists CLOAK & DAGGER

CLOAK & DAGGER Master PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
R128, R1292200, 25%, % W Resistor119000-221
R130, R131LkQ, +5%, 4 W Resistor110000-162
R1I32-R13910kQ, +5%, 4 W Resistor110000-103
R1401kQ, +5%, % W Resistor110090-102
RII, R1421.8 kQ, +5%, %& W Resistor110000-182
RI5O-R15222kQ, 25%, 4 W Resistor110000-223,
R1532.21, 5%, 4 W Resistor110000-222
RIS468kO, +5%, %& W Resistor110000-683
RISS1.5kQ, +5%, % W Resistor110000-152
RISG12 kQ, +5%, % W Resistor110000-123
RIS71009, +5%, % W Resistor110000-101
RIS8180 k2, +5%, 4 W Resistor110000-184
R15915kQ, +5%, 4 W Resistor110000-153,
R16215 kQ. +5%, 4 W Resistor110000-153
R163—~RI6622kQ, +5%, % W Resistor110000-223
R1672.2 kQ, 45%, A W Resistor110000-222
RI691502, 5%, 4 W Resistor110000-151
RI70-R1761kQ, +5%, 4 W Resistor110000-102
R772200, +5%, 4 W Resistor110000-221
Ri783302, +5%, 4 W Resistor110000-331
RI792200, +5%, 4 W Resistor110600-221
Ri803302, +5%, 4 W Resistor110000-331
R1811002, +5%, % W Resistor110000-101
R182, R1836.8kO, +5%, 4 W Resistor110000-682
Ri8410 kf, +5%, % W Resistor110000-103

Sockets

ID/E24 Contact, Medium-Insertion-Force IC Socket79-42€24
2D28 Contact, Medium-insertion-Force IC Socket79-42C28
2F28 Contact, Medium-Insertion-Force IC Socket79-42C28
2H28 Contact, Medjum-Insertion-Force IC Socket79-42C28
2K28 Contact, Medium-Insertion-Force IC Socket79-42C28
2L/M24 Contact, Medium-Insertion-Force IC Socket79-42C24
3c46 Contact, Medium-Insertion-Force IC Socket79-42C40
3yIK24 Contact, Medium-Insertion-Force IC Socket79-42€24
4LIM24 Contact, Medium-insertion-Force IC Socket79-42C24
5B40 Contact, Medium-Insertion-Force IC Socket79-42C40
5CciD40 Contact, Medium-Insertion-Force IC Socket79-42C40
SN24 Contact, Medium-insertion-Force IC Socket79-42C24
SR24 Contact, Medium-Insertion-Force IC Socket79-42C24
6L22 Contact, Medium-insertion-Force IC Socket79-42€22
6M22 Contact, Medium-Insertion-Force IC Socket79-42C22
3j22 Contact, Medium-Insertion-Force IC Socket79-42C22
8L22 Contact, Medium-Insertion-Force IC Socket79-42C22
8N24 Contact, Medium-Insertion-Force IC Socket79-42C24
8R24 Contact, Medium-Insertion-Force IC Socket79-42€24
OLIM.28 Contact, Medium-Insertion-Force IC Socket79-42€28

{continued on next page)

4-22

Page 51

CLOAK & DAGGER

CLOAK & DAGGER Master PCB Assembly illustrated Parts Lists

Parts List, continued

DesignatorDescriptionPart No.

Switch

5A8-Toggle DIP Switch66-18PIT

Transistors

Qi-Q3350 mW, GO V, Switching NPN Transistor34-2N3904
Q4, 058A, 80 V, NPN Darlington Transistor34-2N6044

Miscellaneous Test Points (Acceptable substitute is part no. 020670-01) 179051-002 Interconnect Printed-Circuit Board—includes 60-pin connector, A039431-01 part no. 179153160

4:23

Page 52

CLOAK & DAGGER Iustrated Parts Lists

2m nsrour 2

ces seraur

Figure 4-8 CLOAK & DAGGER Slave PCB Assembly A039938-21 A

4-24

Page 53

CLOAK & DAGGER Tilustrated arts Lists

Eaazfay
pe| ooxo:
nS]as1|°
=o“efaL1—
“coor ae*=)al/:
(fussae)wo|. “

Figure 4-8 CLOAK & DAGGER Slave PCB Assembly, continued A039938-21 A

4-25

Page 54

Illustrated Parts Lists

CLOAK & DAGGER Slave PCB Assembly CLOAK & DAGGER

Parts List

DesignatorDescriptionPart No.

Capacitors

cl100 pF, 100 V, Dipped Fixed Mica Capacitor128002-101
c239 pE, 100 V, Dipped Fixed Mica Capacitor128002-390
C30.1 pE 50 V, +10%, Ceramic Capacitor122002-104
C4-C510.22 wF, 25 V, +20%, Axial-Lead Ceramic Capacitor122004-224
52-54100 #F, 35 V, Axial-Lead Aluminum Electrolytic Capacitor(Acceptable24-350107

substitute is part no. 124001-107)

C55-C1010.1 pE, 50 V, 4.10%, Ceramic Capacitor122002-104

Coil

Li100 uH, +10% Inductor141002-001

Diodes

CRI, CR2Red Light Emitting Diode38-MV5053

Integrated Circuits

1B‘Type-7415244 Line Driver/Receiver Integrated Circuit37-741S244
1c‘Type-7415244 Line Driver/Receiver Integrated Circuit37-TALS244
1DStatic RAM Integrated Circuit1372U-120
1E/FPROM Integrated Circuit136023-309
1F/HPROM Integrated Circuit136023-310
NiPROM Integrated Circuit136023-311
1KPROM Integrated Circuit136023-312
ILPROM Integrated Circuit136023-313
1MPROM Integrated Circuit136023-314
INPROM Integrated Circuit136023-315
2B/D8-Bit Microprocessor Integrated Circuit90-6012
2E‘Type-741S245 Tri-State Octal Bus Transceiver Integrated Circuit37-T4LS245
2F/H‘Type-7418244 Line Driver/Receiver Integrated Circuit37-TALS244
2FType-74L8245 Tri-State Octal Bus Transceiver Integrated Circuit37-TALS245
2HiType-7418245 Tri-State Octal Bus Transceiver Integrated Circuit37-7418245
2‘Type-74L8374 Octal D-Type Flip-Flop Integrated Circuit37-74LS374
2K‘Type-7418138 3-8 Line Decoder/Multiplexer Integrated Circuit137177-001
2LType-74LS08 Quad 2-Input AND Gate Integrated Circuit37-TALSO8
2MType-748260 Dual 5-Input NOR Gate Integrated Circuit37-748260
2NType-741S163A 4-Bit Synchronous Counter Integrated Circuit37-7ALSIO3A
3B‘Type-74LS74 Dual D-Type Flip-Flop Integrated Circuit37-74LS74
3c‘Type-74LS244 Dual D-Type Flip-Flop Integrated Circuit37-7ALS74
3DLine Driver/Receiver Integrated Circuit37-T4L8244
3E‘Type-74L804 Hex Inverter Integrated Circuit37-7ALS04
3HCustom Integrated Circuit137321111
3y‘Type-74153 Dual Data Selector/Multiplexer Integrated Circuit37-74153
3L‘Type-7418139 Dual 2-4 Decoder/Multiplexer Integrated Circuit37-74LS139
3MType-741$163A 4-Bit Synchronous Counter Integrated Circuit37-TALSIO3A
3NPROM Integrated Circuit136023-116
4B‘Type-7406 Buffer/Driver, Hex Inverter Integrated Circuit37-7406
4c‘Type-74LS163A 4-Bit Synchronous Counter Integrated Circuit37-7ALSIO3ZA

4-26 (continued on next page)

Page 55

CLOAK & DAGGER Illustrated Parts Lists

CLOAK & DAGGER Slave PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
4D‘Type-74LS86 Quad 2-Input EXOR Gate Integrated Circuit37-74LS86
4FType-74153 Dual Data Selector/Multiplexer Integrated Circuit37-74153
4H‘Type-741S169A Up/Down Binary, Synchronous 4-Bit Counter Integrated Circuit137109-00L
4yType-74LS169A Up/Down Binary, Synchronous 4-Bit Counter Integrated Circuit137109-001
4K‘Type-74153 Dual Data Selector/Multiplexer Integrated Circuit37-7153
4LType-74L832 Quad 2-Input OR Gate Integrated Circuit37-74LS32
4M‘“Iype-741574 Dual D-Type Flip-Flop Integrated Circuit37-TALS74
ANType-741S175 Quad D-Type Flip-Flop Integrated Circuit37-TALSI7S
SA‘Type-74LS194 Shift Register Integrated Circuit37-7ALSI94
5B‘Type-7418157 Quad Data Selector/Multiplexer Integrated Circuit37-74LS157
5CTWpe-741S160 4Bit/Binary Counter Integrated Circuit377415160
5D‘Type-741S194 Shift Register Integrated Circuit37-7418194
SEType-74LSi94 Shiit Register Integrated Circuit37-74LS194
SFType-74L886 Quad 2-Input EXOR Gate Integrated Circuit37-741886
5H‘Type-74LS169A Up/Down Binary, Synchronous 4-Bit Counter Integrated Circuit137109-001
SJType-74LS169A Up/Down Binary, Synchronous 4-Bit Counter Integrated Circuit137109-001
5KType-74LS04 Hex Inverter Integrated Circuit37-741804
SL‘Type-74LSI09A Integrated Citcuit37-741S109A,
5M‘Type-74LS00 Quad 2-Input NAND Gate Integrated Circuit37-74LS00
5N‘Type-74L832 Quad 2-Input OR Gate Integrated Circuit37-74L832
6A‘Type-74LS157 Quad Data Selector/Multiplexer Integrated Circuit37-74LS157
6BType-74LS151 1-8 Data Selector/Multiptexer Integrated Circuit37-74LS151.
6C‘Type-74LS151 i-8 Data Selector/Multiplexer Integrated Circuit37-74LS151
6D‘Type-74L5157 Quad Data Selector/Multiplcxer Integrated Circuit37-74L8157
OEType-74LS157 Quad Data Seiector/Multiplexer Integrated Circuit37-74LS157
oFType-741S151 1-8 Data Selector/Multiplexer Integrated Circuit37-74LS151.
6H‘Type-74LSi39 Dual 2-4 Decoder/Muitiplexer Integrated Circuit37-7ALSB9.
6Type-74153 Dual Data Selector/Muhtiplexer Integrated Circuit3774153
6KType-741800 Quad 2-Input NAND Gate Integrated Circuit37-74LS00
6L‘Type-741S74 Dual D-lype Flip-Flop Integrated Circuit37-74L874
6M‘Type-74L502 Quad 2-Input NOR Gate Integrated Circuit37-74L802
ON‘Type-74L808 Quad 2-Input AND Gate Integrated Circuit37-T4L808
TA-7ERandom-Access-Memory Integrated Circuit100017-001
7H, 7Type-74i8157 Quad Data Selector/Multiplexer Integrated Circuit37-7418157
7KType-74S00 Quad 2-Input NAND Gate Integrated Circuit37-74500
7hType-74L$74 Dual D‘lype Flip-Flop Integrated Circuit37-741874
7M‘Type-74LS74 Dual D-Type Flip-Flop Integrated Circuit37-74LS74
JN‘Type-74LS00 Quad 2-Input NAND Gate Integrated Circuit37-741500
8A-8FType-4116 Random-Access-Memory Integrated Circuit100017-001
8HType-74L802 Quad 2-Input NOR Gate Integrated Circuit37741802
3‘Type-74LS02 Quad 2-Input NOR Gaie Integrated Circuit37-74LSO2
8K‘Type-74109 Dual J-K Flip-Flop Integrated Circuit37-7409
8L.‘Type-74L832 Quad 2-Input OR Gate Integrated Circuit37-7832
8MType-741S00 Quad 2-Input NAND Gate Integrated Circuit37-741500
8N‘Type-74S74 Dual D-Type Flip-Flop Integrated Circuit37-7AS74

(continued on next page)

Page 56

Illustrated Parts Lists CLOAK & DAGGER

CLOAK & DAGGER Slave PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
9A-9F‘Type-4116 Random-Access-Memory Integrated Circuit300017-001
9H, 9Type-74LS02 Quad 2-Input NOR Gate Integrated Circuit37-74LS02
9K‘Type-74LS74 Dual D-Type Fiip-Flop Integrated Circuit37-74LS74
OLType-74LS02 Quad 2-Input NOR Gate Integrated Circuit37741802
9M‘Type-74S04 Hex Inverter Integrated Circuit37-74804
ONType-74874 Dual D-Type Flip-Flop Integrated Circuit37-74874
10A~10FType-4116 Random-Access-Memory Integrated Circuit100017-001

Resistors

RI, R210 kQ, +5%, 4 W Resistor110000-103
R32200, +5%, 4 W Resistor110000-221,
R4-R6470.0, 25%, % W Resistor110000-471
R7, RB270, +5%, 4 W Resistor110000-270
R9-R1L10 kQ, +5%, %& W Resistor110000-103
R12150Q, +5%, %& W Resistor110000-151
Ri3~—RI71kQ, 45%, % W Resistor110000-102
RIS.4702, +5%, 4 W Resistor110000-471
RI9-R25279, £5%, % W Resistor110000-270
R2610kQ, +5%, % W Resistor410000-103
R271009, +5%, % W Resistor110000-101

Sockets

1D24 Contact, Medium-Insertion-Force IC Socket79-42C24
1E/F28 Contact, Medium-Insertion-Force IC Socket79-42C28
FH28 Contact, Medium-Insertion-Force IC Socket79-42C28
a28 Contact, Medium-Insertion-Force IC Socket79-42C28
1K28 Contact, Medium-Insertion-Force IC Socket79-42C28
IL28 Contact, Medium-Insertion-Force IC Socket79-42C28
1M28 Contact, Medium-Insertion-Force 1C Socket79-42C28
1N28 Contact, Medium-Insertion-Force IC Socket79-42C28
2B/D40 Contact, Medium-Insertion-Force IC Socket79-42C40
3H24 Contact, Medium-Insertion-Force IC Socket79-42C24

Transistor

a350 mW, 60 V, Switching NPN Transistor34-2N3904

Miscellaneous

YI10 MHz Crystal90-123

Test Points (Acceptable substitute is part no, 020670-01) 179051-002

4-28

Page 57

‘TM-242 Ist printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Piease write in the space below.

If you have any technical questions about certain ATARI games products, or are requesting additional) publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm Ci Distributor

Address DC Operator City _— Country © Other ee

Phone: Country Code Local Number

Page 58

First Fold

No postage necessary if mailed in the United States

Milpitas, California 95035 Le

USINESS REPLY MAIL a

FIRSTCLASS PERMIT NO. 173 MILPITAS, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari Inc. a Attn: Field Service/Coin-Op Division 737 Sycamore Drive P.O. Box 906 P| Le | Le

Second Fold

Word

a8po sup adey,

Page 59

T™M-242 Ist printing

YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm 0 Disiributor

Address 0 Operator

City State Zip 3 Other

Area Code Phone

Page 60

First Fold

Attach Necessary Postage

Atari Ireland Limited Attn.: Field Service/Coin-Op Division Tipperary Town, Ireland

Second Fold

‘wosd

Page 61

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

hE BEEK BURR ERK “BURR BIRR BEEK EER BET

Kit Warranty

ment. None of the Seller’s other products or parts thereof are warranted. Seller warrants that its electronic parts supplied in this kit are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of ship-

Ifthe electronic parts supplied in this kit fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such electronic parts which are

returned to Seller during said warranty period, provided: ‘

  • Seller is promptly notified in writing upon discovery by Buyer that said products OM are defective;
  • Such products are returned prepaid to Seller’s plant; and (¢ ) Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties ee expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller’s part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

ak SH, ane Nae ate, a Sate, Se

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to youand others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories, Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 64

PUTT

A. ATARI ATARI, INC. 790 SYCAMORE DRIVE PO. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488 D1 2 Conencston Caney HOUEDO CORON AONU TOAD UUORAONANORONNANNOOTAAONAONEH =

Ly