CATHODE RAY TOMES

Venture Technical Manual 2.0

Venture (version 5 set 1) (Exidy, 1981) · Manual · 72 pages · 38 sections · original scan

Page 1

Venture’

Technical Manual 2.0

Page 2

VENTURE (TM)

Technical Manual 2.0

  • 1981 Exidy, Inc. 390 Java Drive, Sunnyvale, California 94086 Telephone: (408) 734-9410 Toll-free: (800) 538-8402 Telex: 357-499
Page 3

EXIDY VENTURE (TM)

TABLE OF CONTENTS

SCHEMATIC PAGE NUMBER NANUAL PAGE NUMBER

PAGE 1 OF 8: GAME LOGIC PCB .ccscccccccccccccccccsccccereces I

  • Master Oscillator
  • Element (Horizontal) Counters
  • Line (Vertical) Counters
  • Screen RAM Addresses
  • Coin Input Decoding
  • Hardware Generated Line Positioning Proms
  • Blanking and Video Clocking
  • Black and White Composite Video Output

PAGE 2 OF 8: GAME LOGIC PCB .ccececccccccsccccccccsenceccees 2

  • Screen Controller PROM
  • Screen RAM
  • Character Image Storage
  • PROM Power and Signal Selection
  • Character Generator Output Shift Register

PAGE 3 OF 8: GAME LOGIC PCB Image Storage RM ...

  • Character Generator Image Storage RAM

PAGE 4 OF 8: GAME LOGIC PCB, .cccceeccccrccccccccccceccccccces 4

  • The 6502 Microprocessor
  • Power-on Reset circuit
  • Processor Workspace RAM
  • Main Address Decoding

PAGE 5 OF 8: GAME LOGIC PCB...

  • Program Memory
  • PROM Address Selection
  • Memory Device "Personality" Selection

PAGE 6 OF 8: GAME LOGIC PCB ..

  • Moving Object Horizontal Position
  • Moving Object Vertical Position Counters
  • ‘Write Moving Object" Decoding
  • Color Interface Output
Page 4

TABLE OF CONTENTS (continued)

SCHEMATIC PAGE NUMBER MANUAL PAGE NUMBER

PAGE 7 OF 8: GAME LOGIC PCB .cseeeccccccescerecesveescscseee 7

  • Moving Object Multiplexing
  • Moving Objects Image PROM
  • Moving Object Video Output Shift Registers
  • Moving Objects Shift Register Load Logic
  • Moving Object Shift Register Control logic
  • Memory Device Personality Configuration

PAGE 8 OF 8: GAME LOGIC PCB ..eeeeseeeeee

  • Interrupt Status Latch
  • Option Switch Port
  • Control Inputs Port
  • Moving Image Latch
  • Audio Board Port
  • Control Port Latch
  • 1/0 Decoding

Figure 1: MeMmOry Map cececccccccccreccccccsccssecescecssees OD

«. 10 AUDIO/COLOR PCB GENERAL DESCRIPTION .

PAGE 1 OF 5: AUDIO/COLOR PCB. ..seseceecccrceeccccevscececes 17

  • Logic and Power interface
  • Communications and Address Decoding

PAGE 2 OF 5: AUDIO/COLOR PCB. ccessecccvcccceccccsrecesveces 12

  • 6502 Microprocessor
  • Peripheral Interface Adapters
  • Address Decoding
  • Music Generator
  • Master Oscillator
  • Program Memory
  • Output Filter

see ceeccevercces 13 PAGE 3 OF 5: AUDIO/COLOR PCB....seeeeeee

  • Clock Manipulation and Noise Generation Circuit
  • Amplitude Modulation Control
  • Output Summation and Volume Control
Page 5

TABLE OF CONTENTS (continued)

SCHEMATIC PAGE NUMBER MANUAL PAGE NUMBER

PAGE 4 OF 5: AUDIO/COLOR PCB .reccceccccccccccccscecscecseee 14

  • Summing Anplifier
  • Integrator and Audio Power Amplifier

PAGE 5 OF 5: AUDIO/COLOR PCB. ..seececescecccccccceccvecessee 15

  • Pattern Character Color Division
  • Priority Encoder
  • Color Data Latches
  • Color Selection Multiplexers
  • Video and Sync Signal Polarity Selection
  • Final Video Output Re-sychronization

PAGE 1 OF 1: MEMORY EXPANSION PCB ...cseeesecee 16

POWER SUPPLY INFORMATION AND ADJUSTMENTS ...seeeecseessseees 17

JOYSTICK ADJUSTMENTS wecccesecccccescenseccccecccsseseccsees I7

AUDIO DIAGNOSTIC TEST .sscsesccceceecrececccccecccceeesesses 18

AUDIO ADJUSTMENTS ..scscccscccccccccesccccscccccscoceeceeees 19

MAIN HARNESS WIRING DIAGRAM cccccrecscccecccececcccccceceves 20

CONTROL PANEL HARNESS WIRING DIAGRAM .ceeccecccceccecceccees 217

COIN DOOR HARNESS WIRING DIAGRAM ...cceeeccccccccccceeeneces 22

ELECTRICAL SCHEMATIC OF UNIVERSAL POWER SUPPLY ...eseeeeeees 23

ILLUSTRATED PARTS LIST ccscccssccecccccccccccsccecessccsenes 24 Final Assembly PartS sevcccerevsvcccansssvcccsscccsscsesseseesees 29 Drawing, 1 of 2. errr rrr 26 Drawing, 2 of 2. 27 Control Panel Assembly PartS sevcesccevecccseccscccvcscccasecssssccvssees 28 Drawing «+. Universal Power Supply Ass. ly Parts sevcccccccccccvcncnnscecscssccsssovevessseses 30 see e ence eceereceencvceeseese 29

Drawing sovcenceccaccccccecccccccsesecscessceseens 31

Page 6

TABLE OF CONTENTS (continued)

Isolation Transformer Assembly Parts cosceveccceccrcccccccscececescesessesesseces 32 Drawing cecccccccccccvcccvecvcccccscccveceseseeses 33 8-Position Joystick Parts se. seececeeceeee 34 Drawing ceccecceccecceccesecccccccssessccesesceces 35 Coin Door Assembly Parts «. Drawing secesceccccccccceccscceseseeseeccceccceces 37 Flourescent Light Assembly Parts «. Drawing soececceeccccsccccccccccsccccccsescsceeses 39 Logic and Audio Board Assembly Parts seeee Drawing seececcccccccesccccccccccccccccsseseccsoses AT Printed Circuit Assembly- Universal Power Supply Parts sscvcsescevees Drawing eseseeeeeere Logic Board Parts List .... Audio/Color Parts List ... SELECTABLE OPTIONS Selectable Dip Switch Settings ....ccccccccceces 48 cee ceceececececcccsccececes 40

Cece eeecccccccccecceces 42 see ceccceerecccccvceee 43 wee ecccenceccccceecsee 44

Page 7

FOREWORD

In keeping with the progress Exidy has made to satisfy the needs of all those involved with the operation of an Exidy video game, we have duplicated especially pertinent information in both our Operator and Technical manuals. For example, we now are including a complete Parts List and accompanying drawings in both manuals. That way should you need to separate the manuals, the VENTURETM Technical Manual, Version 2.0, contains all the information a technician needs to

service VENTURE 'M, The Operator's manual, then, contains

all information necessary for installation and routine running of VENTURE™M,

We have designed the Technical manual to aid in your understanding of schematics. Each board schematic (logic, audio/color, and memory expansion) is accompanied by a description directly opposite it. These are sectioned by the page number of the drawing they describe.

After the board schematic drawings and descriptions, we provide information on Audio Diagnostic Test, Power Supply, Joystick and Audio adjustments. An illustrated parts list follows.

Exidy welcomes your suggestions for more ways to make provide you convenience. Please use our toll free number (800) 538-8402. We'd welcome your ideas.

Page 8

PAGE 1 OF 8, GAME LOGIC PCB

  • Master Oscillator (1D)

From this oscillator all dynamic operations are derived, such as the processor clock, the main element and line counters, the shift register clocks, as well as all other forms of timing signals.

2. Element (Horizontal) Counters (1C, 1E,

2E) a

These components form the final stages of horizontal timing. All operations in this game requiring horizontal positioning or timing have their origin here. Note that, beginning with signal HCLK (from Clock Divide Counter 2D), there are 256 counts prior to setting signal E256 high. When this signal goes high, it indicates that the horizontal! blanking period is in progress. At this time the final counter (1E) is preloaded with a higher number than previously loaded. This creates a shorter count the second time around. The shorter count measures the retrace interval. When the retrace count is finished, the counter preloads with a lower number, establishing a longer count sequence again for ‘real time‘ sweep of the electron beam across the face of the CRT.

  • Line (Vertical) Counters (4F, 5F, 6E)

These components form the entire vertical timing operation starting with a clock derived from horizontal timing. These counters count 256 times and then preload with a higher number, causing a shorter count the second time. This shorter count measures the vertical retrace interval.

Note that signal L256, when high, indicates vertical blanking is in progress. After the completion of the vertical retrace count, the counters once again preload with a lower number. This way they count 256 times during the sweep of the electron beam down the face of the CRT, allowing the horizontal timers to sweep one complete horizontal line for each count of the vertical counters. Thus, the electron beam reaches the bottom of the CRT, after completing 256 horizontal line sweeps. It then begins the vertical retrace count, and the whole cycle begins anew with the beam starting again at the top of the CRT.
  • Screen RAM Addresses (7D) During the time the screen RAM _ is examined by the logic for output to the monitor screen, addresses must be applied to the screen RAM to count up at a rate corresponding to the image cells conceptually arranged on the screen in a 32 x 32 matrix. The counts used here, 4 from the element counters, and 4 from the line counters, fulfill this timing requirement. The least significant element count used (E8) represents an interval exactly eight times that of one element. The least significant line count used represents an interval exactly eight times that of one horizontal line, or eight times a single line count. Dividing a 256 element line by 8 yields 32, and likewise dividing a 256 line vertical sweep by 8 yields 32. Thus the

screen RAM address lines (RAMO through

RAM9) count at a rate that creates 32 horizontal counts and 32 vertical counts as the electron beam sweeps the face of the CRT. This makes 1024 conceptual "image cells" into which can then be inserted images of 8 elements by 8 lines. For more information concerning these images, refer to the text for pages 2 and 3 of the Logic Schematics.

  • Coin Input Decoding (1H)

Some models of VENTURE (TM) contain two separate coin inputs for special coinage applications. NOR gate 1H combines these separate inputs, making signal 5COINT, which sets the interrupt flip-flop (6— on page 8) when either coin input becomes active, thus forcing the microprocessor to jump to the interrupt service routine. This interrupt driven operation prevents ever missing a coin when inserted. However, this also means that when a game is first powered up, the coin input must be inactive. If for some reason the coin input switch is enabled at the time of power up, the game does not properly initialize until the switch is disabled,

  • Hardware Generated Line Positioning Proms (35, 4E)

These PROMs are not used for VENTURE (TM).

  • Blanking and Video Clocking (5H)

Flip-flop 5H merely combines blanking and all other video.

8 Black and White Composite Video Output (1H)

This circuit is not used for VENTURE (TM). \f desired, however, these components may be installed to aid troubleshooting, by acting as a "video probe’.

Page 9

PAGE 2 OF 8, GAME LOGIC PCB

  • Screen Controller PROM (6D)

This PROM controls the direction of data flow into and out of the screen RAM and character generator RAM. It prevents timing errors and buss conflicts, assuring that the microprocessor can write to either the screen or character generator RAM, or read back from either.

  • Screen RAM (7B, 8B)

The screen RAM is comprised of two 1024 x 4 static RAMs, configured to act as a single 1024 x 8 RAM. This creates a screen matrix of 32 horizontal by 32 vertical Positions. A single byte code is stored in each of these positions to represent a particular character. During "real time" (the time the CRT is being swept by the electron beam) these character codes address the character generator RAM.

These character codes, when used as addresses, are combined with the three least significant line counts (L1, L2, L4) to present to the character generator output shift register all the necessary data to form an 8 element wide by 8 line high character on the CRT, located within one of the 1024 positions mentioned immediately above; that is, the 32 horizontal by 32 vertical Positions.

The screen, then, is a storage place for single byte codes that call up an 8 x 8 character and place it into the corresponding character cell. This chatacter is stored in the character generator RAM, shown on page 3 of the schematic.

  • Character Image Storage

Shown on this page are two PROMs (9C, 10C). They could be used as a permanent set of characters. However, VENTURE (TM) uses RAM instead, to increase the flexibility in character manipulation. This portion of RAM appears on page 3 of the Logic schematics.

  • PROM Power and Signal Selection (10B)

This Dip Shunt configures the logic for different types of PROM devices. For VENTURE (TM), however, this Dip Shunt is unnecessary due to the fact that RAM has been used rather than PROM.

  • Character Cenerator Register (12B) Output Shift

Video from the character generator memory devices (RAM in the case of VENTURE (TM)) is formed by this shift register as a byte of data that displays one line at a time from left to right on the CRT. This ultimately forms an 8 line high by 8 element wide character positioned on the screen according to the time it is presented to the shift register.

Output from this shift register are all the images seen on the screen except the player image and the player missile image.

Page 10

PAGE 3 OF 8, GAME LOGIC PCB

Image Storage RAM

  • Character Generator Image Storage RAM (13C, 11C, 14C, 12C)

These four RAMs, when used in this configuration, act as a 2048 x 8 bit RAM. The images placed on the screen are stored in this RAM by the microprocessor, according to the game program. In this RAM images are established, altered, shifted slightly, and even replaced with a new set, if required by the program. When cal led by the logic todo so, the RAM presents, to the character generator shift register, a single byte, representing one line of a particular image. Each image is composed of 8 lines of data, each line is one byte-wide. Thus, 256 images of 8 x 8 bits can be stored here simultaneously and ‘called up" by the screen RAM to be displayed on the CRT in any of the 1024 character cell positions. A single byte code, stored in the screen RAM, calls up a_ character. The character may change or move by replacing the single byte code in the screen RAM, or by altering the data in the character generator RAM which forms the image.

Page 11

PAGE 4 OF 8, GAME LOGIC PCB

  • The 6502 Microprocessor (2A)

For detailed information concerning this microprocessor, refer to the MOSTEK publication, 6500-10A, MCS = Microcomputer Family Hardware Manual.

One feature that should be mentioned here, however, is that this microprocessor has ‘memory-mapped 1/0*. This means that all ports interfacing to peripherals of any type must be located within the normal memory map, with no duplication of addresses, since no instructions are specifically oriented toward |/O operations.

  • Power-on Reset circuit (connected to 2A pin 40)

When power is first applied to a game, a particular sequence of events must occur to set up all logic conditions. If this sequence is broken for whatever reason, the microprocessor may become confused, and the game will not start and run.

This sequence is accomplished when the reset line to the microprocessor is the last line allowed to reach a "high" logic level. The Power-on reset circuit makes sure this occurs by utilizing the charge time of an RC network as a delay.

If any kind of power interruption occurs during normal game play, the power-on reset circuit insures that the microprocessor is reset. This alleviates confusing the microprocessor, while it also recreates the original power-on sequence.

  • Processor Workspace RAM (4A, 5A)

The RAM, or workspace, consists of the lowest 1024 bytes of memory and can be divided into three separate sections due to distinctly different functions.

The lowest 256 bytes (0 to FF Hexadecimal) is reserved for special software register operations, and is called "zero page’. The processor uses this area to store dynamic variables. For details of this type of operation, refer to 6502 technical literature regarding “Zero Page Addressing".

The next higher 256 bytes (100 to 1FF Hex) is reserved for the 6502 stack. The processor stores return addresses in the stack when interrupted or called to execute a subroutine. The game program may also request the processor to store other kinds of information here for later retrieval.

The next higher 512 bytes (200 to 3FF Hex) are used as a_ scratchpad area. Miscellaneous calculations and their results are temporarily stored here.

  • Main Address Decoding (5C, 5D, 5E)

This circuit is the first stage of the address line decoding necessary to organize the memory map; that is, it places specific functions or devices within generalized blocks of the memory map, grouped by function.

For details on the addressing scheme, see MEMORY MAP, Figure 1.

Page 12

PAGE 5 OF 8, GAME LOGIC PCB

  • Program Memory (6A through 13A)

These memory devices may be 2516, 2716 (5 volt only), or 2732 EPROMS. If 2516 or 2716 EPROMS are used, there will also be an additional memory expansion PCB in use to create more memory space. This PCB is simply an extension of the address, data and control lines present at the memory devices situated on the logic PCB.

Note that four of the lines to each memory device (PCSO through PCS7, PAP19, PAP20, PAP21) are programmable through jumper configurations located at 4B and 11B. This allows different memory devices to be used and/or facilitates interconnection to the memory expansion PCB (if used).
  • PROM Address Selection (4B, 5B)

This is a second stage of address decoding, used to select each individual memory device when addressed. Signal ROMSEL (from page 4 Main Address Decoding) selects the Program Memory devices in general, and jumper 4B, together with decoder 5B further defines an address to a particular memory device.

  • Memory Device "Personality" Selection (11B)

The dip shunt, or jumpers block, alters control signal configuration to the Programmemory devices. This allows the use of alternate size EPROMS and/or those created by different manufacturers whose control signal pinouts may not be identical to one another.

Page 13

PAGE 6 OF 8, GAME LOGIC PCB

  • Moving Object Horizontal Position (13F, 15F, 14F, 16F)

Counters 13F and 15F form a byte-wide counter which horizontally positions Moving Object 1 on the screen. These counters are preloaded to a certain value by the microprocessor during Vertical Retrace time. Then, after each occurrence of the Horizontal Sync, they begin to count. The count outputs AND'ed through 15E give rise to signal MIHW, the Horizontal Position Window for Moving Object 1. Counters 14F and 16F are the equivalent circuit for Moving Object 2.

  • Moving Object Vertical Position Counters (16E, 12E, 1E, 13E)

Counters 16E and 12E form a byte-wide counter which positions Moving Object 1 vertically on the screen. These counters are preloaded to a certain value by the microprocessor during Vertical Retrace time. Then, after each occurrence of Vertical sync, they begin counting. The four count outputs of the least significant of these two counters (MIL1, M1L2, M1L3, M1L4) are sent to the moving object image PROM to specify which line of the image is presently being displayed. The AND'ed outputs of the second counter give rise to signal M1W, the Vertical Position Window for Moving Object 1. Counters 11E and 13E are the equivalent circuit for Moving Object 2.

= ae

CBLB CSYNC 5CVID S5SCLK HSYNC GND VSYNC 5MO2VID = 10 5MO1VID = CONDUEWNa

W VAY 12 5LINES 13 VD7A10 +5V

  • ‘Write Moving Object" Decoding (6F, 16H, 5E, 3F)

Consists of two distinctly different functions. 6F and 16H form the circuit that generates the load pulses for the moving object position counters, while 5E and 3F simply prevent the counters from counting during blanking.

  • Color Interface Output (16B)

This is a 14 pin DIP socket used as the connector interface to the color selection circuitry, located on the audio PCB. The signals and_ their functions are listed below:

5SRLOAD = Shift Register Load Pulse (Neg- True) = Composite Blanking Composite Sync Composite Video (Neg. True) Shift Register Clock (Neg. True) Horizontal Sync

Vertical Sync Moving Object 2 Video (Neg. True) Moving Object 1 Video (Neg. True) Character Generator Address Line 9 NOT USED ON VENTURE = Character Generator Address Line 10

Page 14

PAGE 7 OF 8, GAME LOGIC PCB

  • Moving Object Multiplexing (144A, 14E)

These two multiplexers pass information to the moving objects image PROM. They contain two codes: one determines which image should appear, and the other specifies which line of that image is to be displayed.

The data passed alternates between data for Moving Object 1 and Moving Object 2, depending on the state of element count £32.

The upper multiplexer (14A) passes the “which image" code, and the lower multiplexer (14£) passes the ‘which line of that image’ code.

  • Moving Objects image PROM (11D)

This EPROM accepts as an address the image and line codes of moving objects 1 and 2 (see "Moving Object Multiplexing" above). It then presents the appropriate data for one line of the image to the output shift registers.

The timing of the logic insures that the correct pair of shift registers are loaded with the data, then shifted out at the correct time to became, one line at a time, the 16 lines of video for that character (Moving Object 1 or 2).

  • Moving Object Video Output Shift Registers (12D, 13D, 14D, 15D)

Shift registers 12D and 13D together form a 16 bit shift register whose task is to accept, as data, 16 bits (2 bytes) representing a Single line of the image for Moving Object 1, then shift these 16 paraltel bits out serially to become video. This operation is repeated for 16 consecutive lines, resulting in a video image that is 16 bits wide by 16 lines high on the monitor screen. ‘Shift registers 14D and 15Dtogether form this same type of circuit, identical in function, for Moving Object 2.

  • Moving Objects Shift Register Load Logic (2F, 16H)

This circuit sends properly timed load signals to the Moving Object Video Shift Registers. These load signals are needed to load the image data into the shift registers at locations 12D, 13D, 14D, and 15D.

5+ Moving Object Shift Register Control Logic (15H, 14H)

The input signals to the upper two gates (15H) represent horizontal and vertical position "windows" for the two moving objects (for example, MIHWV = Moving Object 1 Horizontal Window, M2W =Moving Object 2 Vertical Window). These windows allow the Moving Object shift registers to shift only at the right time. This insures the image is generated at the correct position on the screen.

The lower 2 gates of 15H are, in VENTURE, used for later decoding in the color selection circuitry, located on the audio PCB.

  • Memory Device Personality Configuration (10D)

This is another Dip Shunt which reconfigures the PC board in order to use an EPROM (11D) of another type or manufacturer.

Page 15

PAGE 8 OF 8, GAME LOGIC PCB

  • Interrupt Status Latch (8E)

This latch is set when a coin is dropped or vertical sync occurs. When the latch is set, the CPU is interrupted; that is, signal TRQgoes low. This forces the CPU to jump to the interrupt service routine. The interrupt service routine instructs the CPU to check for a coin input, and then run a debounce routine on the coin bits of ports 9E or 15A, depending on which coin input bit was set at 8E.

lf the CPU finds no coin input bit set at latch 8E, it will assume the Interrupt condition was caused by vertical sync. This tells the CPU that it should now jump to the routine that services the normal game play, and that the screen can now be updated with new data. The screen can only be updated during the vertical retrace interval.

Note that this latch also has two signals labeled LNGO and LNG1 which both show PC etched jumpers. These two bits are the select bits for one of four languages, English, French, German, and Spanish.

You may select a language by cutting the

appropriate jumper, allowing it to be pulled to a logic high. For English, no cutting is necessary. See the Operator's Manual for proper configuration of other languages.

Also on this latch is the signal named

TABLE. This signal, tied to a pul lup

resistor and switch, determines whether the program operates as a table model or in the upright game configuration. Please check with the Exidy Marketing Department and the Operator's Manual for more details, since table models may or may not be available.

  • Option Switch Port (15A)

This port provides input from the option dipswitch, at location 16A. Data from the dipswitch is gated onto the data buss and read by the CPU at game start. This allows such options as number of turns, coins per game, additional game versus extra turn, etc.

Note that one input of this port (labeled COIN 2) does not come from the switch. Instead, it comes fromCoin Input 2, and is used for debouncing the auxiliary coin input switch.
  • Control Inputs Port (9E)

This port provides input from the controls located on the control panel, such as the joystick, fire button, one player start, and two player start. Data from these controls are gated onto the data buss for examination by the CPU during the regular service routine (which is synchronized to the vertical interval).

Note that one of these inputs is fromthe COIN1 input (labeled 5COIN1) rather than a game control input. The COIN1 input to this port is used for debouncing the standard coin input.
  • Moving Image Latch Only the CPU can write to the moving image Jatch. This latch contains the code that specifies which image or images are presently being displayed y the hardware moving object circuitry.
  • Audio Board Port

This latch is written to and read by the CPU, and transmits instructions to the audio board when any sounds are enabled, disabled, or the game is initialized. In addition, this port passes data sent to select colors for screen images. For the functions of these instructions, see the audio board schematic and/or description of operation.

  • Control Port Latch (9D)

This latch, used only in table versions, is written to only by the CPU and keeps track of which player is "up", in order to select which controls are active, that is, player one or player two.

  • 1/0 Decoding (7E) The upper half of this decoder generates the chip selects for those 1/0 devices written to by the CPU, and the lower half generates the chip selects for those 1/0 devices which are read by the CPU. See the detailed memory map for more precise information.
Page 16

Figure 1: MEMORY MAP

Hex Address Function or Device

FRFFA-FFFF interrupt and Reset Vectors 8000-FFF9 Program memory space 52XX Audio board communications 5103 Interrupt Condition Latch (read) 5101 Control Inputs Port (read) 5101 Output Control Latch (write) (Not used in VENTURE (TM) upright) 5100 Moving Objects Image Latch (write) 5100 Option Dipswitch Port (read) 50CO Moving Object 2 Vertical Position Latch (write) 5080 Moving Object 2 Horizontal Position Latch (write) 5040 Moving Object 1 Vertical Position Latch (write) 5000 Moving Object 1 Horizontal Position Latch (write) 4800-4F FF Character Generator RAM 4000-43 FF Screen RAM 0200-03F F Scratchpad RAM 0100-01F F Stack RAM 0000-00F F Zero Page RAM

Page 17

AUDIO/COLOR PCB-GENERAL DESCRIPTION

The Audio/Color PCB is so named because it contains not only the circuitry required to generate all sounds, but also the color selection decoding circuitry and video output connector.

This PCB contains a dedicated 6502 microprocessor and circuitry to support the simultaneous generation of many types of sound, including three channel music. The Logic PCB simply sends commands to the Audio/Color PCB via a bidirectional communications port and the Audio/Color PCB takes it fromthere. In some cases this PCB even aids the Logic PCB in some of it's calculations when there is not enough processing time available on the Logic PCB. As a result of this structure, the actual program to generate sounds or music resides on the Audio/Color PCB. There is also a handshake required between the two PCB's in order for the system to power up correctly, and of course, there is no video output without the Audio/Color PCB connected.

Page 18

PAGE 1 OF 5, AUDIO/COLOR PCB

1. Logic and Power Interface (P5, J2,J3)

Connector P5 provides the audio/color PCB with all the power it requires to operate. Also fed through this connector are the two speaker output leads. P5 interfaces only to the power supply module and the speaker, through the main harness.

Connectors J2 and J3 are the most significant path of conmunication between the Logic and Audio/Color PCB's. Address ines, Bi-directional Data lines, processor control lines, and the Audio/Color PCB Select line are all passed through these two connectors.

2. Conmunications and Address Decoding

(9B, 13D)

Peripheral Interface Adapter (PIA) 9B, in concert with 8B (another PIA ,shown on page two) serves as a bi-directional communications path between the Logic PCB and the Audio/Color PCB. During information transfer between the two PCB's, both PIA's are in use. Information from the Logic PCB microprocessor passes through the PIA at 9B to the PIA at 8B, then to the microprocessor on the Audic/Color PCB. When information is passed the other direction, the path is the same, but the direction is reversed.

During the time that no information transfer is occurring between the two PCB's, both microprocessors can continue to operate independently.

Also shown on page one is 13D, a 3-line to 8-line decoder, used to generate the write signals for the Color Data Latches. These Latches will be covered in the text for page five of the Audio/Color PCB.

Page 19

PAGE 2 OF 5: AUDIO/COLOR PCB

  • 6502 Microprocessor (3B)

This microprocessor is the same as that used on the Logic PCB, but is exclusively dedicated to the generation of sound. {t can communicate with the Logic PCB microprocessor, and receives it's instructions thereby. Once jit has received it's instructions, however, it asserts complete control over all Audio/Color PCB circuitry and ignores the Logic PCB microprocessor until such time as it is informed that another conmand is ready. Some commands are of a type that must be processed inmediately, irregardless of other operations in progress, and some conmands can wait until the operations in progress are completed. The program on the Audio/- Color PCB handles all these eventualities appropriately.

  • Peripheral Interface Adapters (8B, 7B)

The PIA at 8B, as mentioned in the text for page one, is used in bi-directional communications between the microprocessors on the Logic PCB and the Audio/Color PCB.

The PIA at 7B is used for two fundamental purposes on this PCB. The first, and most

important, is that it contains the RAM that the microprocessor uses for zero page and stack operations. The PlAonly contains 128 bytes of RAM, which under normal circumstances would not be sufficient for both zero page and stack. In this case, however, the memory map on this PCB has been altered, so that when the microprocessor thinks it is putting the stack at address O1FFH it is actually putting it at address 007FH.

The second use of this device is that of a progranmable interval timer, used for various purposes unique to the specific sounds being generated on this game. The ability of this device to generate interrupts at time out is utilized here.

  • Address Decoding (4B)

Keyboard Encoder (4B) is used here to generate the chip selects of all devices located in the memory map of the Audio/Color PCB.

  • Music Generator (2B)

Another Programmable Counter/Timer device is used here to generate music (and sometimes other special effects) inupto three channels (or voices) simul~ taneously. The music is created by a special software operating system, and all but the counter/timer chip is therefore invisible.

  • Master Oscillator (A1,B1)

This oscillator is the source of all timing on the Audio/Color PCB. If this clock stops running, so does everything else on the Audio/Color PCB. It is, however, completely independent of the clock and other timing signals generated by the Master Oscillator located on the Logic PCB.

  • Program Memory (3A,4A, 5A, 6A, 7A)

The memory devices used here are 2716 (2048 x 8) EPROMS. The DIP shunt located at 8A is used to reconfigure the control and power supply lines, if necessary, for equivalent devices from different manufacturers, Whose pinouts may not be the same.

  • Output Filter Latch (1C)

This latch is used simply to switch different output filter capacitors inor out of the circuit to soften or shade the sound, according to program requirements.

Page 20

PAGE 3 OF 5: AUDIO/COLOR PCB

  • Clock Manipulation eration Circuit (30,4D,6D,5E)

The timers inside Programmable Timer Module 3D can be incremented or decremented either internally by the Phase Two clock input, or externally from the "C" inputs (C1,C2,C3). Both options are used by the program. When the counters are being controlled by the Phase Two clock, the "C" inputs have no effect, and the noise generation circuit is therefore inoperative. In order to generate sounds that are classified as noise, or contain some kind of noise within them, the counters are programmed to decrement in accordance with the input on the "C" inputs. While in this mode, the combination of 6D (Dual *D* Flip-Flop) and 5E (128 Bit Shift Register), are used to "randomize* the clock inputs to the Programmable Timer Module (3D). The "randomizer" can be clocked with either the Phase Two clock or counter output Q1.

  • Amplitude Modulation Control (2D, 7D, 8D, 9D)

Counter (3D) outputs Q1,Q2, and Q3 are already highly complex sounds, but in order to create much more specialized audio they must be modulated in amplitude. Each channel is separately controllable in amplitude by associated Digital-to-Analog converters comprised of analog multiplexers and a resistive ladder network. Three control bits on each multiplexer select a voltage to output, according to which input pin is addressed (since each input pin is tied to a different point, and therefore voltage, in the resistive ladder). The voltage thus selected is applied to one of the two inputs to each segment of 2D (another triple analog switch). The other input is tied to ground. Note that the control bit to each analog switch segment is one of the previously mentioned count outputs (Q1,Q2,Q3). In this manner, each output can be controlled for frequency and amplitude individually.

Note also that the count output from Q1, unlike Q2 and Q3, first passes through yet another analog switch whose function is to turn off the count output of Q1 prior to reaching the Digital-to-Analog conversion stage. This is done because the Q1 output is the one used for selective clock frequency generation, and would therefore interfere with other sounds if not disabled at the appropriate time.
  • Output Summation and Special Effects Volume Control (2E)

The three segments of Operational Amplifier 2E are configured as voltage followers (for impedance considerations), and their outputs are summed together at the top of a 10K POT, R31. The output volume, therefore is determined by the voltage applied at each input and the adjustment of the POT. Note that the resistors used to sum these three outputs together are large in value, so that each channel will have minimal effect on the others when conflicting signals arrive simultaneously (except, of course, that their sum will appear at the output).

This summed output is then again summed with all other sounds generated by this PCB at the input to the final Power Amplifier.

Page 21

PAGE 4 OF 5: AUDIO/COLOR PCB

One segment of Operational Amplifier 3F is used here as a point at which all the various sounds generated on this PCB are brought together. Note that the output goes immediately to a 10K POT (R46) which has ground on the other end. The wiper, therefore, varies the final output volume of all sounds together.

  • Antegrator and Audio Power Amplifier (BF 10F)

Another segment of Operational Amplifier 3F is used here as an integrator; that is, it is used to “roll off* the higher frequency sounds in order to prevent the power amplifier from going into unwanted oscillation. The Audio Power Amplifier (10F) is a Dual Audio Amplifier IC configured as a "Bridge Amplifier" and may be either a LM377 or LM378 for Revision A, Audio/Color PCB. Revision letters are locted at position 11C. in later versions of Venture it may possibly use a LM379 with a reconfigured DIP shunt. Information regarding this is available in the operators manual for this game, or contact the Exidy Customer Service Department for assistance if you must use an alternate device.

Volume Controls

Master Volume R46, see the fourth page of Audio/Color PCB schematics.

Music Volume R9, see the fourth page of Audio/Color PCB schematics.

Special Effects Volume R3, see the fourth page of Audio/Color “PCB schematics.

Page 22

PAGE 5 OF 5, AUDIO/COLOR PCB

  • Pattern Character Color Division (10A, 9A) The two segments of Flip-Flop 10A, using the upper two address lines from the character generator circuit, divide the character generator RAM space into four (4) conceptual groups (or quadtants) according to address. This is done in order to assign different colors to different characters.

Using this method, any character stored in a particular quadrant will be the same color as any other character stored in that same quadrant. If the same character is stored ina different uadrant, it wil! be displayed with a ifferent color. The output of 9A (Twoline to Four~line decoder) applies the separated video lines of these quadrants to priority encoder 10B, whose task is to determine which image is to take visual preference when two or more coincide on the TV screen; that is, which image is to

appear to be in the "foreground", and

ich is to appear to be in the "background".

  • Priority Encoder (10B)

Ali the video signals generated by the logic PCB are applied to the priority encoder. The signals assigned the higher priority are shown at the top, and the lower priority are shown on_ the bottom. The output of this device is a3 Bit code representing the highest Priority video line active at that instant. This output code is then sent to the color multiplexers as an address which will select the appropriate color for the imagery generated on that video line. Note that the lowest priority input to the encoder is tied permanently low (active). This insures that when no other video is being generated, there is a background color present, unless of course, the program has selected a background color of black at that time.

  • Color Data Latches (11C,12C,13C)

These latches are addressed directly by the Logic PCB microprocessor. Here the microprocessor stores the data that determines which character is what color. This data is then passed to the color selection multiplexers.

  • Color Selection Multiplexers (11B, 12B,-T3By

Each of the three multiplexers controls the video output toa different color gun in the CRT. One turns the red gun on or off, one turns the green gun on or off, and the third does the same for the biue gun. The output combination of the three multiplexers provides for one of eight possible colors to be displayed at any given instant. The color displayed is determined by two things: what type of video is present (esge which character), and what color the microprocessor has currently assigned to that type of video. As mentioned above, the color assignations are stored in the color data latches. The priority encoder (10B) issues the code representing the type of video currently displayed. Using these two pieces of information, the multiplexers look at the appropriate bits in the color latches and send the data directly to the TV to turn the color guns on or off.

  • Video and Sync Polarity Selection (TTA, 1ZA)_ — Signal

Before being reclocked one last time, all video outputs are passed through an Exclusive-Or gate (11A), so that one input of each segment can be used to invert the video (make it 180 degrees out of phase with respect to the input to the gate). This feature insures compatibility with TVmonitors made by several different manufacturers.

The TV Sync signals are also routed through Exclusive-Or gate segments (12A) for the same purpose.

  • Final Video Output Re-synchronization (T3A)

To insure that all video signals and sync signals are accurately synchronized in time, they are all re-clocked one last time together by a HEX "D'Flip-Flop. It "cleans up* any spurious irregularities or propagation delays that may have crept into any of the video or sync signals.

Page 23

PAGE 1 OF 1: MEMORY EXPANSION PCB

For information on the Memory Expansion PCB, refer to PAGE 5 OF 8, GAME LOGIC PCB. See section 1. Program Memory (6A through 13A)

Page 24

POWER SUPPLY INFORMATION AND ADJUSTMENTS

All DC _Power required to operate VENTURE is supplied in the Exidy Power Supply Module. These supply outputs are as follows:

+5v DC@6 amps

-5v DC » @ 1 amp

+12v DC (HI) |@3 amps

+12v DC (HI), @ 1 amp

-12v DC (HI),@3 amps
-12v DC (LO)@1 amp

: (HI) refers to "high current*

(LO) refers to "low current"

CAUTION: Only certified technicians

should make adjustments on all components

of VENTURE'™, AC jine voltage selection is available in your VENTURE game by setting the appropriate jumpers on the power chassis. Only the +5v DC _ is adjustable. This must be adjusted to:

+5.00v DC +/- .25v

as measured on the PCB near the microprocessor (location 2A). JOYSTICK ADJUSTMENTS

The leaf switches on the 8- position joystick should be adjusted to a dimension of .218" to 250" (7/32" to 1/4"). This is measured from the edge of the joystick shaft to the tear leaf. See the drawing below. Misadjustment will cause the joystick either to activate too soon or to make the 45 degree directions hard to activate.

+s

L\ ADJUST TO _BE FROM .2i8 TO.250 FOR IDEAL SWITCH OPERATION.

Page 25

VENTURE'M AUDIO DIAGNOSTIC TEST

When VENTURE™ js first powered on, the following message appears for eight seconds:

STAND BY

VERSION X

(X= particular version number).

Five seconds after power on, one or more quick beeps, like an organ chord, are heard. This is part of the Exidy Audio Diagnostic Test. The number of beeps that sound indicate different conditions of the Audio board. The following code is an indication only, of where to first check the Audio Board. Because this diagnostic test only evaluates certain components, other circuitry is relied upon for the test. Should this other circuitry fail, the diagnostic test may not, then, point directly to the failure. Please use the results of this test as a guideline for further troubleshooting.

The code is as follows:

0 beep: If no beeps are heard, along with a hum or random notes, this may indicate a failure in 3A and/or 7Aw

1 beep: All audio hardware is OK. However, be sure to check the Attract Mode Cycle anyway fora possible message to check the Audio Board. In _ occasional instances, this can occur. The message will further direct you.

2 beeps: ZERO PAGE RAM failure. Check 6532 RAM 1.0. Timer Array at location 7B on the board.

3 beeps: (will not occur)

4 beeps: ROM failure

INTERRUPT failure. at location 7B. 5 beeps: Check 6532

In addition, this message appears during the Attract Mode only if the Audio Board needs to be checked:

"CHECK AUDIO BOARD"

xX YY XX and YY in the message are code characters defined as follows:

XX= 01 = ZERO PAGE RAM FAILURE, check 6532

02 = (will not occur)

n3= ROM FAILURE. Any number in the XX position ending with a 3 (for example, 23, 33, etc.) indicates a ROM failure. The first digit (2 and 3 in the Previous example) points you to the appropriate chip that needs to be checked. The code for the any number ending with 3 in the XX position is as follows:

Chip to Check 03 3A 13 4A 23 5A 33 6A 43 7A

Note: The message reflects the first bad chip it encounters, in numeric order. It is possible for chips following it to also be bad.

04 = INTERRUPT FAILURE, 6532. check

2? = FAULTY COMMUNICATIONS. Check 6520 at 9B.

Here is the code for the second two numbers in the YY position.

YY= 40 = Communication from Logic Board to Audio failed. Check 6520, both locations 8B and 9B.

80 = Communication to Logic Board from Audio failed. Check 6520, at locations 9B and especially 8B.

<0 = Communication between Logic and Audio failed. Check 6520, both locations 8B and 9B.

Also, the symbol <0 in both the XX and YY position, along with a hum or random notes and no beep after power on, may indicate a failure in 3A and/or 7A.

Page 26

AUDIO BOARD ADJUSTMENTS

The following drawing points out the three individual audio adjustments and the location of the DIP switch. The audio board rides piggyback on the logic board, mounted on the right wall of the game, when viewed from the rear service door.

MASTER VOLUME

SPECIAL EFFECTS rar VOLUME

{ Li!

Poy =a] |

=I il | [ i! = 1 | ml ie 1 MUSIC VOLUME

fl 00 = . _ J

fl Uo

B POSITION DIP SWITCH

Page 27

REVISIONS, oH TOLERANCES UNLESS

SPAREJi‘DESCRIPTIONaOTHERWSE SPECIFIED
SPARELOGIC BOARDREVISE PERECNFROREGTONTees7

SPARE

‘SPAREay© x:
SW.BUF D6(IN)Sake DOWNwesT/ GRx
‘SW. BUF. D4 (IN)IREBLU/YELNEXT ASSYUSED ON
SW. BUF. D2 (\N)WAY BHT -WAT 7 ORNeo | tone
sw. BUF DO (in) | 8,ONEPLAYER STARTGRN/RED

GRN | GaN GRN

GRN GRN GRN [—GRN GRN GRN T+]

J 20! MONITOR VIDEO

+ m2

SW-BUF. D7 (iN) ‘SW.BUF.D5 (IN) SW-BUF. D3 (\N) ‘SW. BUF. DI au

ANTI- SLAM #12y (0) “SV

+5V +5V

+5V +5 +5V

COIN 2 INPUT

afd Mi

Gy /euKS¥/REDRED

Gy /GRN ceN 7c th GY/ WHT H SYNC

SINBLUBRN/ WHTV SYNC
B WAY UP.WHT/REDGRNGND

& WAY LEFT WHT/ VIO 2 PLAYER START GRN /YEL

BLU/ORN ORN/BLK VAO/ BLK oO

GND V SYNC

HSYNC BLU DATA GRN DATA RED DATA RED RED GRN. RED RED. RED BRN/WHT cy /wHT GY /BLU GY /GRN BLU / WHT GY /RED

GY —NUTOD Nboo= N<x€<C 4UDUZErACTAmgoOGEy PNGay

Jal AUDIO COLOR

GRN ‘ORN YEL YEL/BLK Vi0/ BLK ORN/ BLK, BRN RED BRN GND + lav (Ht) #12 (HI) ~12 v (LO) -5V +12 V(LO) SPKR(A) + 5V SPKR(B) + 12vito) -5V ~12Vv (1.0) —12v(Hl) ~rav( ki) GND GOSNOMDUN— GEGN= WHT/ GRN BLU/ORN BLU/WHT YEL YEL/BLK ORN/ BLK.

a P8 SPEAKER Sener 5 J14 Jil 0, J 7 N-Onanr OAR REGULATOR | 5y BOARD PWR SUPPLY J AUDIO

-5V +12v(Lo)

SPARES J. POLARIZING KEY JI BETWEEN PINS 5&6 ~12v(HN) 12v(Lo) ONE PLYRSTRI|

WAY OOWN

Bwar LEFT WAY RIGHT

ANTI SIAM

PROPRIETARYDESIGN DRAWING———_————Rrmure.oescnenow

=0 Sf * haaaLe WIRING DIAGRAM eras avALanLe upon ‘on Sactose To ores Tener Reaves Sak foorse seo MAIN HARNESS

Page 28

ONE PLYR START

8 WAY DOWN

BWAY LEFT

BwaY UP

B WAY RIGHT

FAST Ok FIRE

TWO PLYk START

ale Mi Alo m2

+5V

+5 GRN/ RED JOYSTICK oH OTHERWISE TOLERANCES UNLESS SPECFED

WHT/GRN SI FIGHT

$2 PROKECTION

Od & PLACES.

xx

TEXT ASSY

DOWN REVISIONS T-2445: 10} VENTURE 7 [+

ce ma ¢ |e Z

$3 TR REVISE PER ECN

LEFT

S4

WHT/ Vio wHt/ RED WHT/ ORG Buu/YEL

GRN/YEL uP

oO SS TWO PLAYER

S6 ONE PLAYER

S7 FIRE LEFT

390 JAVA DR ‘SUNNYVALE, CA 94080 408-734-9410 noes untess omenmise specimen: PAGE 2 pmesorsenrn™t WIRING DIAGRAM CONTROL PANEL HARNESS 71-2391 —10

Page 29

INCH

TOLERANCES UNLESS

rrr) OTHERWISE SPECIFIEO

PROJECTION

Oka) PLACES. MM BUN +i}+ NIN|S + etl + +

ANTI-SLAM

COIN 2 (AUX) H+ IH+1

NEXT ASSY USED ON

7t-2444-+10 | VEMTURE

BLU/WHT

BLU 7—SRN BLU/WHT +—»

GRN

a ee S| MECH | NO COM NO COM

$2 MECH 2 GRN

BLU/ORN Lee NO i } $3 SLAM SWITCH

AUX. COIN COUNTER

COIN COUNTER

REVISIONS, ZONE ) LTR DESCRIPTION ]__paTe ‘APPROVED A —— AS PER ECN [7-30-81

NOTES UNLESS OTHERWISE SPECIFIED:

on om) acer a ava WIRING DIAGRAM ~ UNIV. [evecxeo Ze OIN DOOR HARNESS

enaween Parson wa! SUNWALE TOLERANCES eS Perle 7\ -2449 -10

ancues- —o __[PROPPIIETARY, se enopeny or] DESIGN DRAWING Siueaaimererem” | aribsinanaas vow DO NOT SCALE DRAWING

Page 30

E beta a

[7

Jl

i /

Jl HT REVISED PER ECN

TLRER 24 VCT._ 4AMP

Tey vac

TIRER, J3

ul

lo

!

USED ON 77-3365-15 | VEOTURE —5V +12V (HI)

+12V (LO)

12V (LO)

—12V (HI)

GND

SPARES

PLACES «

x

XX Xxx ft

ZA SHOWN FOR REFERENCE ONLY IN MICROFARADS

|, ALL CAPACITOR VALUES ARE

> OTHERWISE SPECIFIED

INCH

yp

te TOLERANCES UNLESS PAGE 25

f fF an Ea MM

“

NOTES UNLESS OTHERWISE SPECIFIED:

orawn Br TIE ol <— ve ve | C ; —— ee ey Ca) coe GR a ow. sayaon le — BT ees 11 4

DESIGN DRAWING SCALE

CA 94086 Pracnona: 7 PROPRIETARY me _— femgmuarvon =| — | DO NOT SCALE DRAWING

THIS DOCUMENT is THE PROPERTY OF

408-734-9410 EXIDY INC. AND May NOT BE REPRO- DECIMALS xe axes DUCED Of OISCLOseD To OTHERS. WITHOUT WRITTEN AUTHORIZATION.

Page 31

APPENDIX A: ILLUSTRATED PARTS LIST FOR EXIDY'S VENTURE'M

The following is an illustrated parts list to aid you, should you ever need to order new parts for VENTURE Ml The drawings have all parts labeled by a number within a circie. This number refers to the item number on the Parts List directly across from the drawing. In the case of the Final Assembly listing, the second drawing has numbers referring to the Final Assembly list as well, which is found across from the first drawing.

Following the Illustrated Parts List is a list of parts for the Audio/Color and Logic Boards.

Page 32

6.1 VENTURE™ FINAL ASSEMBLY

item Part Number

Banaue wn a 1D38-5137-10 038-5142-10 C38-5120-10 D38-5134-10 C38-5136-10 096-0136-10 196-0136-11 096-0136-12 1D96-0136~13 196-0136-14 1D38-5135-10 1038-5130-10 076-1225-20 £71-2443-10 71-2250-10 €71-2442-10 €38-5133~10 C71-2440-10 B68-0035-11 B68-0131-10 €75-5194-10 C75-5185-11 C75-5186-10 68-6050-20 (68-0124-10 B68-0142-10 €68-0141-10 B89-1018-10 B89-1019-10 B89-1020-10 B89-1021-10 C89-1016-01 C89-1016-02 70-6053 72-3000 68-6050-10 74-6524 74-8532 74-4601 74-4606 74-5464 74-8534 74-8544 74-5468 74-6513 74-6506 63-7061 88-4002 87-1001 87-1062 33-5049-20 33-5048-20 33-5040 89-1009-10

74-5198 C76-1250-12 67-5000 Description

Assy, Cabinet Assy, Control Panel Assy, monitor Assy, Universal Power Supply Assy, Isolation transformer Assy, Coin Door 25 cents Assy, Coin Door Assy, Coin Door Assy, Coin Door Assy, Coin Door Assy, Flourescent Light Assy, Logic and Audio Color Board Assy, Door Assy, Main Harness Assy, Isolation Trans Harness Assy, Speaker Harness Assy, Power Cord Ground Cable Oblong Speaker Grille lamp bracket Logo Plex Ambient shield Display Plex Coin box lid Mounting Bracket, Logo Plex Panel Hasp, Coin Box Interlock Switch Bracket Label, Serial No Label, Fuse Labe!, Voltage, 110V Label, Voltage, 220V Decal, Side art Decal, Side art Light, Flourescent bulb Switch, Interlock Coin Box, Univ. #10-24 x 1 1/2" large carriage black #10-32 x 1" Ig. soc. button head black #8 x 5/8" Ig. pan hd, x-recessed type AB #8 x 1" Ig. flat head x-recessed type AB #8 x 1/2" |g, sheet metal socket head, type AB Black #10-24 x 2" Ige hex hd. mach #10-24 x 1" Ig, carriage, Blk #10 fender washer, 7/32" 1D x 1 1/4"OD #10-32 kep nut #10-24 kep nut speaker small tywrap, 4° minature packing list envelope plastic bag, 10" x 12° Venture Technical manual Venture Operator's Manual TV Manua!, Wells-Gardner #19K 4605 FCC Warning Label

Retainer clip (flour.) Cleat Lock and Key Assembly

Page 33

Ooe) Ox

GP ZAXATIACH KEY (COW) SOOAGTY 1) TO MUSIDE OF COW DOOR. section AA REFERS TO FIWAL ASSY ZX PLACE KEYS (REAR DOOR QTY 2)(COKN) PARTS LIST (TEM KUMBER. BOOR- QTY 1) [0 BAG (ITEA@)) AND SEAL

FOR PIL SEE 38-SI4(-10 PALE 2lo

Page 34

REF REF

REE

6) REF REF © Ber

ISOL.XFMR. (@) oh ad @ COIN DOOR @) SPEAKER Mansur’ (CONTROL, PANEL MONITOR ou fis

COGIC ECE

COLOR-AUDIO PCB.

: 8) ess) 0): REFERS 70 FIWAL ASSY a“ PARTS LIST ITEM NUMBER.

NOTES UNLESS OTHERWISE SPECIFIED: PALE 27

esenemmme | sai 20: See ST SE ST LL SEE SATA | RE See ASSY, FINAL: VEKUTURE BBR | ormsmunsem DOWOT ecALE DAC se Es - Sersee0

Page 35

6-2 CONTROL PANEL ASSEMBLY D38-5142-10

Item Part Number Description

1 D38-5138-10 CONTROL PANEL FAB 2 D75-5197-10 POLYCARBONATE OVERLAY

338-5143-108-WAY JOYSTICK ASSY
4B38-0140-10LATCH BRACKET
5D71-2445-10CONTROL PANEL HARNESS ASSY
672-3022SWITCH, PUSHBUTTON W/ NUT & WSHR.
774-0203PAL-NUT
872-3062PUSH BUTTON
972-3061SWITCH ASSY
1074-524710-24 X 5/8' CARRIAGE BOLT, BLK.ZN
174-650610-24 KEP NUT
1274-8545#6-32 X 5/8* LARGE FLAT HEAD X-RECESSED MACHINE
Page 36

(6) / / LLo-° "'N

GRN (BOT) WHT/ORN

  • GaN warsern| rs GRN/RED RN eran | y WS ‘ | _GRN/YEL

BLU/YEL GRN

WHT/ViO

REFERS TO CONTROL PANEL ASSY PARTS LIST (TEM MUUMBER.

PALE 29

NOTES UNLESS OTHERWISE SPECIFIED:

FOR PARTS LIST SEE 38-5142-10 PROPRIETARY DESIGN DRAWING ae , Frasoesonron Beerae nua nG Peemem ns monsms w0N : CONTROL PANEL, ASSY, - SeaTac iene | rannemnanee Stora VENTURE ™

Page 37

6.3 UNIVERSAL POWER SUPPLY ASSEMBLY, D38-5134-10

Item Part Number

C76-1258-10 74-3503 74-2516 74-5198 74-3500 74-3502 78-3001 63-4028 C77-3365-15 C71-2389-10 C71-2446-10 BB CMNaDUAWN A

ao Description

POWER SUPPLY MOUNTING BOARD SCREW, PAN HD, #6 X 1/2" LG. TYPE AB SPACER, #6 x .125 NON-METALLIC SCREW, PAN HD. #6-32 x 3/4" LG. WASHER, FLAT, #6 NUT, KEP, #6-32 POWER SUPPLY, 5V @ 6.0 AMPS TRANSFORMER, FILAMENT, 24V @ 4.0 AMPS PRINTED CIRCUIT ASSEMBLY UNIVERSAL POWER SUPPLY HARNESS, POWER SUPPLY HARNESS, POWER SUPPLY FLOURESCENT

Page 38

):REFERS TO UNIVERSAL POLIER SUPPLY

  • ASSY PARTS LIST ITEM NUMBER. A\, VOLTAGE ADJUSTMENT FOR PARTS LIST SEE 38-5134-I0 NOTES UNLESS OTHERWIDE SI PAGE 31 MONVERSAL PWR SUPPLY f= ere Assy, - VEUTURE™ vt |38-51384-1
Page 39

6.4 ISOLATION TRANSFORMER ASSEMBLY, C38-5136-10

Item Part Number Description

163-4029TRANSFORMER, | SOLATION

2 B76-1259-10 BOARD MTG. TRANS

374-5463SCREW, PAN HD. #10-24 X 1.00" LG
474-5468WASHER, FENDER, #10
574-6402WASHER, FLAT, #10
674-6506NUT, KEP, #10-24
761-80583 PIN MOLEX RECEPTACLE
861-8055FEMALE MOLEX PINS
961-80572 PIN MOLEX RECEPTACLE

10 WIRE, COPPER, STRANDED #18 AWG

1174-8536TERMINAL, RING #10 STUD
1261-8072SPLICE, BUTT
1361-8054MALE MOLEX PIN
Page 40

asanoay waLim — ae — sr stwmioag| ONIMVHG 3TVOS LON Od vo-gaiveatatiee — Fironoes] SEL ROY a | xxoeie-es ji somuno | ENE 3, ‘ON SMU] 1 40] 3¥NLASN-NOLLV OSI ‘ASS Fl | | says) SAWYOISNVYLL vou awosaara| "9-08 8) Ve nawavua

‘salva

awuaivn XX-9E1S-BE 1ST SLYVd YOS 1GaIsIO3dS 3SIMUSHLO SS3INN SALON

WIBWNN WIL) 1S SLvvd CVOILW70S! ‘ISSW YIWYOISNWYL OL SYIIIY4

Page 41

6.5 8-POSITION JOYSTICK, LEAF 0D38-5143-10

74-6540 C92-1024-10 74-6525 B68-0030-10 73-9081 B68-0135-11 B68-0143-10 B68-0135-14 C68-0139-10 10 72-3077 11 75-5193-10 12 74-8540 13 74-5471 14 74-5466 15 88-4037 16 88-4036 17 74-8541 18 74-3500 19 19-5199 20 75-5196-10 CONauawna 10/24 NYLON, INSERT STOP NUT SHAFT, JOYSTICK SCREW, 10/24 FLAT HD X 2 1/2 LG. PLATE, UPPER SPRING, BELLEVILLE SPACER, VERSION 11 DISC LOWER SPACER VERSION 14 PLATE, SWITCH LEAF H SWITCH, LEAF (WICO) NYLON LEAF SW GUARD #6-32 PAN HD MACH SCREW X 5/8 LG. RETAINING RING TRUARC MFG P/N 5133-50 BUSHING MOLYKOTE GN LOCTITE #271 #6-32 NYLON INSERT STOP NUT #6 FLAT WASHER KNOB (BLUE) PLATE, DECORATIVE

Page 42

PARTS LIST (TEM NUMBER. (ITEM). a REFERS TO 8 POSITION JOYSTICK ZX WERICATE, (ITEM®) 1.8.0F BUSAILL,

NOTES UNLESS OTHERWISE SPECIFIED: PALE 35 & mae Venture ™

foorroe 3410 JOY STICK 8 POSITION

Page 43

6.6 COIN DOOR ASSEMBLY, D96-0136-10

item Part Number Description

166-4003COIN DOOR, DOUBLE (VENDALL)
2D71-224-10HARNESS, COIN DOOR
374-3502KEP NUT, #6-32
466-4002COIN ACCEPTOR, 25 CENTS
Page 44

BLU/ORN

GAN

BLU/ WHT

SRN

~(0)-REFERS TO CONN DOOR ASSY PARTS LIST ITEM WUMBER,

PROPRIETARY DESIGN DRAWING s ‘ ‘ pT RL we ne ee re Siero Meets ene a et heateat “ay DONT SCALE DRAWING " _—— | € 406-734-0410 VENTURE” (

3 1

Page 45

6.7 FLOURESCENT LIGHT ASSEMBLY, D38-5135-10

1 70-6052 FIXTURE, FLOUR.

3 71-2447-10 HARNESS, FLOUR. LIGHT

Page 46

REFERS TO FLOURE SCENT LIGHT ASSY PARTS LIST (TEM NUMBER,

FOR PARTS LIST SEE 38-SI35-10 PALE 39 Scsanonmme OT = a TE oe mein | S:£KENO : : sean FLOURESCEMT LIGHT ¢ RHEE ee KD, DowOTscauzonawma " => Se sEEe0 (8 ASSY- VENTURE™ VT | 38-5135-10 3 1

Page 47

6.8 LOGIC AND AUDIO BOARD ASSEMBLY D38-5130-10

OUAWNaA 77-3374-15 77-3387-15 74-5065 74-5182 71-2439-10 74-5173 PRINTED CIRCUIT ASSEMBLY LOGIC PRINTED CIRCUIT ASSEMBLY AUDIO COLOR STAND-OFF NON-METALLIC #6~32 X 5/8 SCREW, PAN HD. PHIL #6-32 x 1/4 LG CABLE ASSY, RIBBON WASHER, FLAT, NYLON #6

Page 48

ef al

X= REFERS TO COGIC ¢ AUB BOARD ASSY PARTS LIST (TEM UUMBER.

FOR PIL SEE 38°5(30-10 ror Tsao onan ; rey MD woaaon PFGeIe a AUDIO ‘THIS DOCUMENT IS THE PROPERTY OF ‘SUNNYVALE P _ THN Bee R TS” | omsaransron are TeraneTEnamEER r + SA sMoRe BOARD ASSY - VEWTURE

Page 49

oa wo

CONAUAWNA PRINTED CIRCUIT ASSEMBLY-UNIVERSAL POWER SUPPLY, C77- 3365-15

UNIVERSAL POWER SUPPLY BOARD 20-4000 CAP, ELECT. 4000MF, 50V AXIAL LEAD 21-4010 CAP, ELECT. DIP 33MF 25V + 20% 21-4015 CAP, ELECT. DIP 6.8MF 25V + 20% 46-3016 DIODE 60S1 or UT4010 47-3004 RECTIFIER, BRIDGE MDA-970-1 47-3041 TRANSISTOR, 2N3055 47-3011 TRANSISTOR, 2N6246 48-2337 REGULATOR 7905 48-2217 REGULATOR 7912 48-2338 REGULATOR 7812 ° 68-3041 HEATSINK 68-2038 HEATSINK 61-8010 CONNECTOR 12 PIN (WAFER HEADER) 74-2514 SCREW, PAN HD #4-40 X 3/8 LG (PHIL) 74-5191 NUT, KEP #4-40 88-4001 TYRAP 5 1/2"

Page 50

uu QS ra) Cc a REF. DESIG. COMPONENT LIST

= REFERS TO UNIVERSAL POWER

SUPPLY PCB ASSY PARTS LIST APPLY HEAT TRANSFER COMPOUND FOR PARTS LIST SEE 77-3365 — 15 (TEM MUMBER. TO ITEMS 7 THRU 1!

NOTES UNLESS OTHEAWISE SPECIFIED:

  • Tr one

UNIVERSAL POWER SUR

‘CHECKED ye fay PCB_ASSY -veMWTURE™

ASY ENGINEER JORAWING No. 77-3365-15

390 JAVA DR souecr

Se JAvA Da TOLERANCES Rone, CA 94086 FRACTIONS = [ANGLES = —a——

408-734-9410 L Fao pcliaeis ws rover or] DESIGN ORAWING ae sans + BRE SARS ene” | REARS MMAR UP DO NOT SCALE DRAWING

Page 51

6.10 LOGIC BOARD, 77-3374-15

Item Part Number

ONAN EWNA

NNNKRKNA BA aaa ay GAAWNASCOBURHABWRAD

is} a 77-3374-15

48-2000-11 48-2005-11 48-2010-11 48-2015-10 48-2020-11 48-2332-11 48-2035-11 48-2316-11 48-2045-11 48-2055-11 48-2067-11 48-2071-11 48~-2307-11 48-2321-11 48-2090-11 48-2095-11 48-2100-11 48-2115-11 48-2328-11 48-2350-11 48-2314-11 48-6502 48-2334 48-9219

48-9099-01

48-9099-02

46-3025 49-5135 59-5120 59-5115 59-5110 59-5105 51-0003

51-0002

51-0001

51-0004

23-4033

23-4035 Description Location

LOGIC BOARD ASSEMBLY 1 LOGIC PRINTED CIRCUIT BOARD 1.C. 74LS00 3D, 15C, 15H 1.C. 74LS02 1H, 6H, 8F 74LS04 1D, 4D, 3F, 10F, 11F 1.C. 7407 2c 1.C. 74LS08 SE 1.C. 74LS11 3H 1.C. 74LS20 2F 1.C. 741521 12F, 15E 1.C. 741827 7F, 2H 1.C. 741532 6F \.C. 74LS74 1C 1.C. 74L$112 2E, 6E 1.C. 7415138 5B, 5D 1.C. 74158139 7E, 16H 1.C. 74LS157 14A, 14E 1.C. 7418161 1E, 2D, 4F, 5F 1.C. 74LS166 12B, 12D, 13D, 14D, 15D (.C. 7418193 10E, 12E, 13F, 15F, 14F, 16F, 11E 13E 1.C. 7418241 1A, 3A, 15A, 3B, 6B, 9B, 8C, 7D, 9E, 4H 1.C. 7418245 3C, 4C, 6C, 13B, 15B 1.C. 7418374 1F, 14B, 7C, 9D, 8E MICROPROCESSOR 6502 2A 2114 RAM (1K x 4) 4A, 5A, 7B, 8B, 11C, 12C, 13C, 14C 6301 PROM (256x4) 5C VELSC-1 6331 PROM (32x8) 6D HRL6D-1 6331 PROM (32x8) 14H HRL14H-1 1N4002 DIODE 8E, 9F, 2H RES. 470 OHM 1/4W 5% 1D, 2H RES. 1.2K 1/4W 5% 2c RES. 1.8K 1/4W 5% 1C, 2c RES. 2.2K 1/4W 5% 7E, 2A RES. 2.7K 1/4W 5% 1C, 2C RES. 220 OHM 1/8W 5% = 9E 10 Pin Sip RES. 2.2K 1/8W 5% 16A 10 Pin Sip RES. 4.7K 1/8W 5% 15A 10 Pin Sip RES. 6.8K 1/8W 5% 144 10 Pin Sip CAP, .O1uf CERAMIC 1D DISC CAP. .1uf CERAMIC A/R DISC

Page 52

LOGIC BOARD, continued

Item Part Number

6.11

Saomrugauawne o 21-4015 20-4014

20-4005

72-3025

72-3042 45-3036

61-8041 61-8062

61-8045

61-8035

61-8060

61-8157

21-4021 59-5138 59-5179 23-4067 48-9224 48-9225 48-9226 48-9227 48-9228 48-9229 48-9230 48-9231 48-9220

AUDIO/COLOR

48-2307-11 48-6520 48-9209 48-6502 48-9210 48-9211-11 48-9212 48-9213 48-9069 Descri

CAP. 6.8uf 25v DIPTANT CAP. 33uf 25V ELECTROLYTIC CAP. 470uf 10V ELECTROLYTIC DIPSHUNT JUMPER PAKS 16 PIN DIP SWITCH 8 POS. CRYSTAL 11.289mhz (SERIES) CONN. 10 PIN MOLEX DIP SOCKETS 16 PIN LOW PROFILE DIP SOCKETS 24 PIN LOW PROF ILE DIP SOCKETS 40 PIN LOW PROFILE DIP SOCKETS 14 PIN LOW PROFILE DIP. SOCKETS LOW PROFLE CAP uf 25V DIP TANT 18 PIN Location

1C, 15D, 6E, 13F 1C, 2c

10H

4B, 118, 10D

16A 1D

16C, 16F 4B, 11B, 5C, 6D 14H, 10D 6A thru 13A, 11D

2A

4A, 5A, 7B, 8B, 11C 12C, 13C, 14€ C45 thru C52, 5D, 2H RES. 220 OHM 1/4W 5% = R200, R311 RES. 18 OFM 1/4W 5% R300 thru R302 CAP. 330 pf CER. DISC 5D E PROM, 2732 VEL6A-1 6A E PROM, 2732 VEL7A-1 7A E PROM, 2732 VEL8A-1 8A E PROM, 2732 VEL9A-1 9A E PROM, 2732 VEL10A-1 10A E PROM, 2732 VEL11A-1 11A E PROM, 2732 VEL12A-1 12A E PROM, 2732 VEL13A-1 13A

  • PROM, 2716 VEL11D-1 11D

BOARD ASSEMBLY 77-3386-15

PRINTED CIRCUIT BOARD 1.C. 74LS138 13D 1.C. 6520 8B, 9B 1.C. 6532 7B 1.C. 6502 3B 1.C. 6840 3D 1.C. 7418154 4B 1.C. 8253 28 1.C. 4069 1A 1.C. 4013B 1B

Page 53

AUDIO/COLOR BOARD ASSEMBLY, continued

item Part Number Description Location

1148-2010-111.C. 74LS045D
1248-2000-111.C. 74LS006B
1348-2314-111.C. 74LS3741C, 11C, 12C, 13C
1448-92141.C. 40532D, 4D
1548-92151.C. 41756E, 73, 8E, 9E
1648-92161.C. 45625E
1748-2067-11(.C. 74187410A, 6D
1848-2342§.C. LM3243F, 2E
1948-2013-101.C. 74061D
2048-2341-111.C. 74LS86T1A, 12A, 4E
2148-9217.1.C. 40517D, 8D, 9D
2248-2321-111.C, 74151399A
2348-91121.C. LM37710E
2448-2079-111.C. 741814810B
2548-2080-111.C. 74515111B, 12B, 13B
2648-2333-111.C. 74LS17413A
2748-4035+1 uf. CERAMIC CAP 25v 1A thru 7A, 9A, 11A, 13A, 1B, 6B, 9B, 11B, 1C, 11C,

13C, 1D 3D, 5D, 7D, 9D, 11D, 13D, 1£, 2E, C7, C9, C10, 3E, 5E, 7E, 9E, C12, 13E, 2F, 47, 12F, 9E, 2E, 3F

2823-407022pf CERAMIC CAP 16V C1
2923-4033+01 uf CERAMIC CAP 16V C6, C8, C11, C33, IC
3020-403033uf CAP, 25V,C13, C15, C17 thru

ELECTROLYTIC W/AXIAL C21 LEADS

31-20-4006100uf CAP ELECTRO-c16

LYTIC 16V

3220-40094.7uf CAP ELECTRO-C3, C4, C5

LYTIC 16V

33.20-40221.0uf CAP ELECTRO-C27, C32, C2

LYTIC 16V

34.59-5115,1.8K RES. 1/4W 5%R3, R4, RS
35.59-51003.3K RES. 1/4W 5%R6
36-59-51251K RES. 1/4W 5%R14
37-59-501610M RES. 1/4W 5%R2
3859-5182300 OFM RES. 1/4W 5% R1
39-59-5045100K RES. 1/4W 5%R10, R11, R12, R27

R47, 428, R29

4059-507022K RES. 1/4W 5%R15, R30
4159-50251M RES. 1/4W 5%R32 R33, R35
4259-506533K RES. 1/4W 5%R34
4359-51052.7K RES. 1/4W 5%R21
4459-506327K RES. 1/4W 5%R44
4559-51191.3K RES. 1/4W 5%R26
4659-5130680 OFM RES. 1/4W 5% R19

47-59-5136 330 OFM RES. 1/4W 5% = R7, R8, R24

4859-5184160 OFM RES. 1/4W 5% R25
Page 54

AUDIO/COLOR BOARD ASSEMBLY, continued

{tem Part Number Description

59-5185 59-5186 59-5080 54-5019 51-0001

45-3048 72-3025 61-8060 61-8045 61-8103 61-8035 61-8062 22-4025

61-8203 61-8042

68-0071 48-9232 48-9233 48-9233 48-9235 48-9236 82 OHM RES. 1/4W 5% 39 OFM RES. 1/4W 5% 10K RES. 1/4W 5% 10K POT 4.7K RES. PAC 10 PIN SIP 3.579545 MHZ CRYSTAL 16 PIN DIP SHUNT 14 PIN DIP SOCKET 24 PIN DIP SOCKET 28 PIN DIP SOCKET 40 PIN DIP SOCKET 16 PIN DIP SOCKET «47 uf CAP ELECTRO- LYTIC 16V 10 PIN MALE CONNECTOR 10 PIN FEMALE CON- NECTOR HEATSINK STAVER V7~1 E PROM 2716, VEA3A-1 E PROM 2716, VEA4A-1 E PROM 2716, VEASA-1 E PROM 2716, VEA6A-1

  • PROM 2716, VEA7A-1 Location

R20 R22, R23 R16, R17, R18, R42, R45 R9, R31, R46 4D

2A BA, 11E J20, 1A, 1B, 5E 3A, 4A, 5A, 6A, 7A, 2B 3D 3B, 7B, 8B, 9B 2D, 4D, 8A, 11E, 6E- 9E, 7D-9D c14

P21 J2, 33

ONLY W/ LM277, LM278 3A 4A 5A 6A 7A

Page 55

SELECTABLE OPTIONS

VENTURE™ has several switch selectable options controlled by an 8-position DIP switch located on the main logic board at position 16A. This switch is accessible through the back door of the game. The Previous drawing shows the location of the DIP switch. The following drawing shows the particular functions controlled by the 8- position DIP switch.

Pence/U.S. and other of

Number of Turns sc

Number of Turns 1)

Number of Coins ol

Number of Coins Sd |

Bonus Points a

Bonus Points Pt] ao not used os

Functions of the 8- position DIP Switch

Page 56

5.1 Selectable Dip Switch Settings

VENTURETM j shipped with the dip switch already set for optimum dollar return. Should you decide to change the settings, you may select any of the following options by setting the proper switch accordingly:

A. COINAGE Switch Switch Switch

458
2 Plays - 1 CoinOFFOFFOFF
1 Play - 1 CoinONOFFOFF

2 Plays - 2 Coin

1 Play ~- 2 CoinOFFONOFF

2 Plays - 4 Coin

=

Play - 20 pence ONONON

3 Plays - 50 pence

B. TYPE OF COINS Switch

U.S. and other OFF English coins ON

D. NUMBER OF TURNS Switch Switch

6 7

2 Bows and arrows (turns)ONON
3 Bows and arrowsOFFON
4 Bows and arrowsONOFF
5 Bows and arrowsOFFOFF

E. BONUS BOW Switch Switch

(Extra turn awarded23

when selectable number of points are made).

Extra turn forONON

20,000 points

30,000OFFON
40,000ONOFF
50,000OFFOFF
Page 57

REORDER NUMBER: 33-5049- 20

Page 58
Warning: This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manuals, may cause interference to radio communications. As temporarily permitted by regulation, it has not been tested for compliance with the limits for Class A computing devices pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference.
Page 59

gt 14 PIN DIP SOCKET (FROM LOGIC PCB position 4B)

off

o# ot!

os [rv [= Sy oon

La [a c?

SPRA 1G PIN DIP PATTERN: w/seRs included as shown

(ay double as 16 PIN input cocket)

JZ

24 PIN DIP SOCKET (FROM LOGIC PCB position 13A)

2 +5VOC 2 i} ct 22 AG 33 21 FAP2i T lov (mn) 9 22__PAP20 17 PAPI9 18 PCSYX oll RD7 te RDG OL _- RDS 14 RD4 Sig RD3 fo} is [= |-s]o0]s Jos foy La fo fome)

poor Assen pe" 502 LociC PCB 77-3374-14 REV E | pop EvphuDeD mencRY NOTES: 4. For EPROMS +5V Vcc) = PIN 24 OND = PIN 12 2, 10 ep, BYPASS CAPS WIT SHOWN, Between +5VDC and GND, VAWE te JOvGnu) Ceramle Ok)

All lines BUSSED TOGETHER except CHIP SELECTS (PCSX, PCSB—-PC SIS)

U3u4usUGU7usU9a
2116211627\627162716271627162G
EPROMEPROMEPROMEPROM,EPROMEPROMEPROMEPROM

(Sv onty) | (Sv omer) | (Sv one¥) | GV oncY) | (5v onc) | (Sv ONLY) | GV ONLY) | (Sv onLY)

18iiaVeia18Pe1?18Ve

resx | CSB PCSY_| _PLSIO resi | pesi2 | pcs PCSIF pes is|

jmeonenrnot MEMORY EXPANSION PCB powers " ie (77- 3389-4) 77-3389-I1 {A SCHEMATIC

3 1

Page 60

21-20 C19 C18 CIT Tift Sa zt z 33pF 2505) 2vacHl “i vaclO)

70 , Feel MAN HARNESS SPER Js +5vde

SPKRO

To Logie BOARD

P2.

THIS TABLE REFERS TO POWER £ GUD PINS NOT SCHEMATICALLY REPRESENTED.

DEVICE TYPE +5 GNo

toNOTE:652020
7ALL RESISTORS AREY WATT 5%.4069‘4
oaALL_CAPACITORS ARE IN MICROFARADS20134
P32| ALSUNLESS OTHERWISE SPECIFIED.65028

6532 20 isis 24 9253 24

BYPASS .1uf FORteam20
EVERY OTHER IC.LS138te

i380 a Lsi39 ie ars ie 4053 le LsT4 cs Uso4 4 7408 rs ans % 4081 1 poss “ zag e ying we tsi “e = FS © OB ew VOB G4

NOTES UNLESS OTHERWISE SPECIFIED: Frrcesorscnrnow forawneno. PROPRIETARY DesaN onan PR a1 [une : [ NEAL R. 200K MARK VON STRWER SUNNWWALE AVDIG/COLOR PCB 77-3587-H CA 94086 SCHEMATIC — DIAGRAIN gcumen 5 me PRoeERTY OF 408-734-8410 Be Bene Mo uarereenems” | orm wauasiewon races SR Saree RONEN, enisy MARK VOW STRWER DO NOT SCALE DRAWING

Page 61

ic

TALS374,

look oe Music SH 3 [52027 [> Ao 2 4B rn i +s eb, 7 Ad _s fe agp Ss me gs 7Lsis4 — |a_383t 2 we io jp so-7, 1.8K 63)

PROGRAM MEMORY

5A 3.579545 MHZ AQ

NOTE: 4013 PINS 4.6840 MUST BE GND. INVERTERS 40698 PINS 9¢1) GND.

+09,

DIP SHUNT

NoTES UNLESS OTHERWISE SPECIFIED. eee nmAY | besawonawme [MMNEAL R. Z00K PARK VON STRIVER £2 soosnynon reser pio [ZoLar. PCB Gena manasa omen anenel [ronorscaeonanne SCHEMATIC DIAGRAM MARK VON STRWER

Page 62

AOA v2 a

& 1s99 1

¥

NETARY BREN Res ANS ua NOT oe EERO” FRUNOREATON acer

oz, +5v

oe De 44] at D5,

ut fe) 2D

DS

be

oD Dp BM bai Az 7 23|

25| a

a2 4175 BE

Te i im 9 bo jw

Ao

esenorawne PME AL R-ZOOK eas. MARK VON STRVER i oxen 1D o

gt on Bai (ay

sce von eae Waar WARK VON STRWER DONOT SCALE DRAWING 390 JAVA OR ‘SUNNYVALE, Ca sa096 408-734-9810 AUDIO/COLOR PCB SLHEMATIC. DIAGRAI 27k Ral

isk, Ree

800 RF

sso Ra4

tox ROS

82% R20

zag R22

29g RIB

NOTES UNLESS OTHERWISE SPECIFIED:

er Fe | | 17-3 387-\I

Page 63

DESIGN DRAWING PMNEAL R. ZOOK MARK YON STRIVER

NOTE 1: L377 oF L379) DIP SHUNT CONFIGURATION DOTTED LINE FOR LM379 SOLID LINE FOR LM3T7y LHiSTE

Rae MASTER VvoLumME

PARK VON STRIVER AUDIO/COLOR PCB SCHEMATIC DAGRAM, seer (STL)

Page 64

RED DATA LATCH COLOR SELECTION

720 18 [57 27 WZp6

DiP SockeT ConNEcTORapepes Rae
SSRLD'3hs 3 afro
[| ceigg 3374 aswip SOT
SCSYNG4 jz IC a2}Vv Low=TRUE

SCvid lw SSCLK Bo a vue whe a GND

Smo2vid 5SMOAVID. GREEN DATA VA4 18 1 SLINES '7 VD7A1O 14 +5VDC 13 FROM Logic rE J4 RIF~ BQ AR HAWNA ~

z

POLARITY OOo cur ror

Cow = TRUEDAww, A
25)ae> CSYNCA
SCSYNC}) ge2}] 86

PATTERA CHARACTER COLOR DIVISION kis

, TEN 8 Hsynce ae 9) 8G

(2A, VD7AIO ; LSavte\. _vsyaca Ys! + }) 86 WBLU

PRIORITY ENCODER

Smosvid SMo2 vi BLINES - P2i EsPicez | eSPICED J0 PIN WAFER HEADER esAcED ESPACEO REDA RED_OuT GRNA GRN_OUT BLA BLU OUT

CSYNCA,CSYNC OUT.OurTruT TO
HSYNCAiHSYNC OuTTY MONITOR
VSYNCAVSYNC OUT(THRU MAIN,

HARNESS )

390 JAVA DR me Audio @ioR PCR ni reas DIAGRAM 77-3387-1)

Page 65

anne TERED

8|76J4321

REVISIONS Tone [UTR BESoRTON oare | APRONED | 6-I2-BI| KI

CLOCK DiviDEHARDWARE GENERATEDEKS

LINE POSITIONING MASTER OSCILLATOR

[asreR oscuearoe]Peon’CE peo]MR

q D coms D lI H2ET Mx i6COINL taxa

Me7s,432_Is|uo
4*=ctwMe) Gerth
Do,cin A—4B__a|[a+2181 527 0} ion4gSFViD
v—€2a8_2| yor31 SH—

—£44_4] USED £27 A

66be NESov,
7eTzse_£8__s|Sif
AzmaLasVIDEO SUMMING]

Bak MOLT. “SMoavoT

ELEMENT (HORIZONTAL) COUNTERSseu uf Ext 1g |wl lig vseBLANKING # VIDEO
432 _Is|wo 41] es974 Le HSEwor axeSDCBLBCLOCKING
<1) Bee Lytif[ix enous
calLiaJ13|ia roescal,¢
£283! yor-BEQ56 3la 6ER56a ai
£64 4) usED‘5CBLB 4z 6C$LBSH
£3a_7|Vet Hlog 1vidéWe @ eb
ce 6usinc el2—tr
fas1g2 theaee?
+se28 13)deefeud
c—4109
25speaus

5uas¢ +598 \8@—e De SCREEN RAM ADDRESSES SSRCLK

  • <—
eaeal® "LpRay

sail

seeEGa} 5341 LigRAMS
E326iRAND
E162RAM)———_

nor use

£82AnoBack ¢waite |“
Randbuaa.aKComposITE
LINE (VERTICAL) COUNTERSRANERieVIDEO OUTPUT

B PANT SCSYNE

SESED Volt a

Pa.leENJ8.RANG

a - HL S16 wesad

“me ——— 5)Za4 S24) LigAAS.

aD ayaa) Lal cox

7"i4
_60iz-
vonTesbpyaoel' "T '2 wrStay ge nts
7'1 Bes68
+tabScant 15}1 GCOINtaa q t™eT Tes
Le.SCOIN2 13,6COINZ

138 L

Lg[Reo] BR Lehtoom bescRTON
£836PARTS LIST
scae,Bhnensione nae mw REHES=
LotINeotewanees Ae:

Pracons DECMMs ANGLES

Aa 7——=Bemm amas[on | 6502 GAME LOGIC PCB

SYNC AND VIDEO GENERATION

1DO_NOT SCALE DRAWING SHE ] CODE TOENT RO. [ DRAWING NO D 77-3374-|| RAVE SCALE sweet

Page 66

SCREEN CHIP SELECT and Buss DIRECTION DECODING PROM Db? 2|A Bl is

de.37
Igo ia]a_cssRDS416
VSEL 13TesterDa5iS
au fa] 4331 [@ csceeiGBDD36] iszas [4
YD7AI0 1 eos 5 SESBDDz.7/138 [3
Rw 10] “Gp fa SeceBo 220DI@[2
3 DBOIR R311C3001bo3a

proc [3 _DBOIR 350

En fos® fe —swr a+ TF SCREEN RAMseccso 8 |

ECGBO 18 ENA

§6-1 [TESED cub 12[soo)ot\ SSR b(ine. CODE STORMEDa

3D = VO7AIO rt

18Rama 1s[ > 48VAS 22

+ + YO? 14 V 13 Si

\o =RAM & \@ce 717VAB 2a PROM 17 +3 p3>o 2 iCGVID
14 .RAM 717Ey14VA? iteVDO 2
iz;RAMG 1+t3VAG z1s Lt tvos 0
3RAMS 2Ta'Ssr*VAS 34ifyou. 10
5tTRAM4 3S4Aa +13atvba 5CHARACTER
7TaVAR 5MWvo2 4 | LSiGe
RAMS 4| 7B1+12BGENERATOR
EA RAM2~ 58vad é sc 104 | vor 3\WDEO OUTPUT
RAM 1 GVAL 7a+ YDO 2SHIFT REGISTER
ten 71RAMO 7 |,VAO aVex

eee oo |

C8SR 8 |—cscGi 18SSRLD | 15. 7

od Sg

awassseas sq vt
Ray_sce Pi agcir
4 2) Ny] 18+ VRP2I ey] NOT USED& cr
Al07 fea ey] 3iw 4feTT) |vee2o 20sscuKl 7 | oly
BO iS5+ul @ |Ls24\ [14Lvrris 9).
isz41454a8See Page 3o

vA i

12 1*2 12iECGBD Te
Esso 3713
5ESB'1\4*¢227
a2af23lo
3AIO 2[a The hgy| PROM [is
z ausAg 41@caz14
=AB4+:TT
Coar Bie¢4aTI
7ae 17 |tseai [3+ [==
cesar a |A°aSSszt] oe LS
ae 0" icsAa 132+>
Gone OwBS 7my¢a

SECGBD 1) — ? rey cscGz 18 Ss

D72 8)ieECGBD vs————de a
de37VRP2Z_ 21 Of8D
D5 41vRP20_20
D4515az, fea er}VRPIS 19
DzG@ |is24s [14AV 15)5See Page 3
a7] ec hg20 13 sea 7
dD812

ECGBD 19 CHARACTER IMAGE

iy)3uw——— ze

5es8D 3 | STORAGE Dao 1 EN See Page 3 for paDIR doe J bal Alteruate: RAM used

2iFor PROGRAM generated
Promichangeable imagery.

POWER ¢ SIGNAL \

SELECTION [>oOH
NO SHUNT; AOS 1%'
DEED TMS GAME3° fio502 GAMELOGIC PCB

tHe 1

f!=aod

7 oor C128) WZ =

DIP SHUNT YIREQ RAM CHARACTER GENERATOR

NOT USED THIS CAME AND SHIFT REGISTER 20F8 733781

Page 67

CHARACTER GENERATOR IMAGE STORAGE RAMS

For vse with PROGRAM generated chaugeable imagery.

vag 15u v7yas. 15ny vo7
vas, ry12 Vevas \e12 VO

VA? 17 | 1024%4 [ia vos VAT 19] 0244 Ts Vos VAG 1] RAM [ee vo+ RAM [ia voa

B| 24 ana a] 13¢ 14c

a 7|

10 SWK Uh 4

vas 15vag 15]u vo3

Va 6} j024x4 wa 6 fi2 voz VA7 7 VAT 17] 102 ‘3 vor

aa] RAMwae 7] 40

vas z Vas z] Ram VA4 B] eis waa 3] 2ua VAS ay} ue VAS a] we vee 5 | Vaz 5 val 6 va @ vao. 7 VAO 7 cacg; 8 cscGe 8 GSWR JO. GSWR_ 10

6502 GAME LOGIC PCB

oe GEE KE IMAGE STORAGE RAM

sore

Page 68

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 69

PROGRAM MEMORY See TECHNICAL MANUAL For PROGRAM #’s,

s22 IngpLRDIRO?Ag22D? aRO?
as23 agoc [ieRDGRDl»23,pel ©ROG
Ae.opat bieoa
aSahsbalROSROSaS.3pal®RDS

a]

ala,pelt!RD2RO2,aa4paleRoe
AS5 3DI 10RDIRDIASSspI 10ROI
AZGRDAa3RDO
Inepol 3RDO1OGpo}
xanal7
AO8 AoAO
134Joaao
PCSO 1B dennPes!Bena.pessoaDATA BUSs

Se | TERMINATION

Papel 2iPAP 2i_ al5.

Ringing S. i

rar 20 20PAP 2020gi") >uPeression

PAPI 19 FAP 1919

4.1K 2 SIP

as2R30
rs227
A?1 jegee 5Fo; iabe 3RI2: Asbs iaRD!A?i) "soe isRDS:
FsFaiapalsae“2 Ineoa|*Lil2 Awoat 4aelacD4
he> AS,DaAS3 ASD3. EyRDSAS3 las.bs 3B—e$ lasD3 3
Inebe aRDAd4 4be uwRopeAa4 Nagpz uWlagD2! utDe
AB5 revilleRDIAB5 Ipsbt 10.ROIAB5 reyDA 10.RDIAS5 3ol 10RDY
K33RDO
=& lane.}RDOAzeo lnbol 3RDO=G@ nzboRDOs£ lac.bol
aAlaLatz AlCoE
coSlagAOBlaoAOAoAo6.8K X SIP
9ABA7AoAiad
Pes4 161818
EWAFess dey,PosedenaPOs? Bg ena
PAP 21 2PAP 21 2PAP 2) 2)
PAP 20 20PAP 20 20PAP 20
PAPIS 13.FAP Ia 13]PAP 1g 19

PROM ADDRESS SELECTION Configuration Shown 7s for +5v ONLY 2732 EPROMS. See TECHNICAL WANUAL For coufiguration for other memory clevices. DIP SHUNT

MEMORY DEVICE PERSONALITY SELECTION

Configuration shown 1s for +5V ONLY 2732 EFROMS, See TECMICAL MMAMUAL for configuration for otlver manory devices. EXIDY INC.

ore 6-72-81 aer7Z =e 6502 GAME LOGIC PCB CPU ROM SOFB

Page 70

MOVING OBSJECT 1 HORZ, COUNTERS MovING OBJECT 2 HORZ, COUNTERS

mew bo? De. ai oS .

D4 DS t dz t Dy T + Do *

SwMIK Swm2h

wish fiof gsis fiols1 fist ho)
Pup 313a{/PRE AB CD )ISPUP 3.PRE A BC Dy/'34[/PRE A BC DY/!3
T4L8193vasiss YSITS748193,
MHOL.5ise 0 hie.5ISFiz(MHCLK.14F125lerNe
our ape oNKor ascotcur a ec DNcr a Bc DN
4 3]2]e]74 13]2]@[7 13/2|e[714 /3]2/e[7 13,
z\o MInWal. \S

Ese) i2l.s2v } Vv

v3ise3

MOVING OBJECT 4 MOVING OBJECT 2 VERTICAL COUNTERS, VERTICAL. COUNTERS}

ov . de +

De . D3 + be Cy) ; Tt DO °

swmiy swmeVv

u [ists folsdu ists olsdu [isl polo
pur 4PREA BC D,/IR4[PRE A BCD) ISPur 44[/PRE ABCD JI3
faisis3sV “yaisiaa74.8193
cBLB510k125cs12CBLB5Ise12.
eure AB oc DNctr apc oNck a Bc DA
aiPry4 ]3]2]e]7

+ Peo Vv

TOFi3
AILZlise, 2 vw1Olis2i
MIL4S|Aer13
MIL,4te

mitt

15,sb?Sway,

nausisa 10 SWM2H z@

Peea0‘SWMIV
14xSWATH

IN ob

SCBLB 5 ENG MHCLK BeLK 3 jusog/ H [es0# BF

“WRITE MOVING OBJECT’ DECODING| 1SE.

ler mew S'SRLOAD o CBLB 2 SCSYNC. z SCVID 4 SSCL —ssciK Sd HSYNC. 6 z VSYNC. 8 —mozvip 2} Smoiip 10 VA _ “ LINES 2. | vom _13 | 45, “6B 14 PIN DIP. SOCKET VIDEO oureuT To Aubig/calor PCB

6502 GAME LOGIC PCB

[a OT PU MOVING OBJECT POSITION 60r 8

Page 71
MOVING OBJECTSMOVING OBTECTSMovING opreCT 4moyiING oBtecr 2
MULTI PLEXINGIMAGE STORAGEVIDEO OUTPUTVIDEO ouTPUT

SHIFT REGISTER SHIET REGISTER

MRI ‘

M2RB__ 13 Pe 122a7MYDS4MyDS aa
mers 10)7VD.
mene Baye23 9716 LeNV D-12] atsieoo (3 MIIvO 12|sarsioel!S _Mevio
& B ay 7\ EPROM isMVD@®iMVDG W
MeRI alg int214MYDS10MOS tS)
MIRE 14 an3WSMVDSSsMvO4 3
mIR4 ul saElo 4uMVD34MvD3 4
mire 5),s| HID fioMVD3MVD2 8
MIRI 2 Ao3mvOt2MVD a
14aa1d4D
£32 ‘beet8] PROGssctw 7Ksscuk 7]!
SeemRel 21 | #SESRI | 0sears o|'*
mReo_20pura 3Pura 3c!
mes 13ism isct®srs stk
MRIB 181 s/t——¥ svt
—_sip— st
  • 10D __ _ ry
me 3) igt BYP| pura 'lo mrs!
ms Baa a2\20 fis'
Le ee expt1 €32 [314 MRIS
mut 34toed1AVD! 14
mat Ale:43!MvD8myoa 4
laa'5izmreo |iAVDT | asiee UEmo? 2], 13
me S| oy1 oss710'mvos_10] >mYDS__10
mitt Ee| 3s_ ree 3tmWVDs =MVD4_ 5S
1oEMoet tape oy ow es ee oe Sy mt eteMYDS 4MVD 4
£32 eey DIP SHUNTmye 3myo2 3
SewAvDI zmvDI 2
ENAMEmMoRY DEVICE————
JY18D
PERSONALITYsex?) 4,sseux 7/15
SELECTIONSEsRe_ 6)"SEsra G on
ConSiguration showsPUP4 30aPur+ 3 eik
is For S vOLTONLyLsRe 15 =ALSR4 i5 ~
MOVING OBSECTS2G EPROMvqetTqsit
SHIFT REGISTERSstaz

LOAD LOGIC

E25 SELDAD 14 1 5ESRI Eos 32x8 oo Ele _13| prom [2 _SESRZ

5E8ATA1ese sé3 SESR3
aw ty344 Eee
mv z|usoona SESR4

Pe Ger ul @ EM2VID

1 # Lsoo, SB MIR Ese 8 5 roy RRLIAH-| f | tsa0 p& Rie 2|Ls00 3 *f o (sc

isc _5|ts00EMviD 5‘snowor
MeRIoiscmivio 4 [1800 j=WOT

es Em2viD__ 10

IMAGE SELECTION LOGICrr) | shisoo } 8SMO2VOT

Which Moving Object?) 15H

MoviING OBJECTS SHIFT REGISTER CONTROL, LOGIC 6502 GAME LOGIC PCB

oon 67RD LEA mo SS MOVING OBJECT VIDEO GENERATION ors 77-3374 -W0

Page 72

$1 SELECTABLE] od loom fe} OPTION 2.2K (SIP) A/o ree pew ad switch MOVING OBJECT LATCH IPSWITCH PORT IMAGE A/D CONVERSION a LATCH en uze ef> lia ix Net sed tesa ook bs ‘la uP Glia were los 17 Io 13] 7aus241 | 7 P| is374 [ie mere Ge 4 15 J 5 B > +t *« Saez. ue 8 2 nor usep |! L v7 3 . BI 12 ek wes a + @ 3 2 _MIRS 7 + 4 + 5 MIRA MIADO Le. Zz ap ions Ne + { 7 A MIR2 ADSEL = = 2 COIN2 sa [ig 7 a] 48 [Sie ian [4 lac TABLE _| ie SwaoL 13 o u SEDIP {13 1z ! cur ial ts00 5 |Lsoo ——Herk 26 D 10 13H OF mzapo '34# a |isoo +5 an cre | CONTROL INFuT] p02 4002 PORT AUDIO BOARD ro Rie (2) PORT « 0. Beowa 24 Yhe ala Bia aBD7 R19 R20 304 Down 4 | 748241 lio ad 3] use4s [17 appa So 10K 310K G ry aa d3- 2 ace iar { uP. t 4 We ABDS ee tose R503 t | [rme 8 12 + 5 15 _ASD4 = 01 asa WoT USED Tt \2H R504. t werT 7 3 1 @ 14 ARDS po = 659 WAT t Riser 15 5 t 7 13 ABDE CR3 R23 rae Ree | | 257ART 13 7 4 3B v2 ABOY oS] yerne A454 1K 3p ie WA israrr i] SE [3 3| ise [i aspo Ss zh, De + BBseEL 13 |—_ = +SV GBOK ra) seyw ENA OD Lm3400 -————oir

83% 3300 wine PO mzao 4 07 a t an Nor USED t Os CRA eS + 4. DATA Naa54 1 syne ts + O3 BUSS i 02 +5V, GBOK > T Dl R21 > DO T/0 DECODING INTERRUPT DECODING +sv [INTERRUPT CONDITION LATCH R310 GF SL256 18/0 Qlis ae 8139] 9 CBLB 3 LANGUAGE 2.2K (8374 = ADS EL ——— M5, . ' cond 17 Ve Rr Waite 12 Ia 3Pio Z)it0> Zyrpens 1 MIRIG 2plo _ ee (ee Tex) coma cy 15 j4| 18374 [is meri asl, (pu sweet SMOLVDT 12 SCOINT 3 12 hd Fy 12 7e 4 RO 4], 7E ope swmot SFVID It rece 3 @ t * 3 @ nF 4 PIED) oF 5 o uf PRE MOOT 4 5 = = Tose, 2 5 )LS32 J - = = 31 f SB%3h72 SEIR smozveT_@)t8020 BLK 13 | TALSNe iver 7] @ t 7 é CIEE) SR/W 1 Se ope SEAD 7 oF avk ives 8] 8& [a 3] 90 fs er pe SEAD avis 2], GE lo * we 45V AL 3 5 SESR WW SWCPL 1 9 ao el, 7 jPa senip SMOIVDT S cur 4 dec Tete ° L256 SEIR + +5v joc R200 SVECRY 3 via R4 220 VENTC wk SCOIN2 Eos re PERIPHERAL CONTROL TC R308 200 ho ec satel tT a] TES 7 E16 RESET eae =5¥ _CI=N) At Ge- a NRITE Gara +5v oH cal +12 Az ASSEL R . 70 al GEM) AUXILIARY COIN S23 Ww TI=10 thre Ji-21 4 a a INPUT. “ _Gs7] 3 5O Pence etc. me GDS @502 GAME LOGIC PC I/O PORTS