CATHODE RAY TOMES

Gun Kit Manual

Gun (Nintendo) · Kit Manual · 22 pages · 14 sections · original scan

Page 1

GUN - RIT

FOR INSTALLATION IN Any UniSystem'or DualSystem cabinet

Page 2

TABLE OF CONTENTS

  • Contents of Gun Kit Il. List of Tools Needed 0.6... cece eee teens 2

Ill. Installation of Gun Assembly IV. Wiring Diagram V. Reorder Parts List

WARNING

The gun for this game is made of a metal frame encased in rubber. It has been designed by Nintendo to prevent injury to players or damage to the video monitor and game cabinet. However, there are risks if this game is used improperly. These risks and the steps you should take to avoid them are as follows:

  • The gun could be removed from its cable by acts of vandalism and therafter misused. When the power to the game is ‘‘on,” an alarm will sound if the gun is removed from its cable or the cable is removed from the cabinet. A warning sticker alerting players to this alarm is posted on the metal holster. Replacement stickers may be obtained from any Nintendo distributor. A security chain may also be attached to the butt of the gun and anchored to the cabinet (see Instruction Manual). The game should be placed where its operation can be monitored at all times.

. The gun could be mistaken for a real gun. Do not place this game where players operating it or pointing the gun may be mistaken by the police or public. THIS WARNING MUST BE POSTED ON THE BACK OF THE GAME CABINET. (LABEL INCLUDED IN KIT) NINTENDO OF AMERICA INC. REDMOND, WASHINGTON 1-800-633-3236

Page 3

|. Contents of Gun Kit

PARTS NAME QUANTITY REMARKS

Gun

Holster

Cable Clamp Assembly

M4 x 6 Hex Head Cap Screw

MS x 8 Hex Head Cap Screw Holster Bracket

Backing Plate

M4 x 15 Carriage Bolt

M6 x 30 Carriage Bolt M4 Cap Nut

M6 Cap Nut

062-4A Gun Power Harness

062-15P Short Harness

3mm Hex Wrench

Alarm Sticker

Warning Notice Sticker Tie Down

Security Chain Retainer Kit

Chain Retainer G

Chain Retainer CP

Rivet

Hammer Drive Screw sea waren n pn paan Complete Assembly

For Gun

For Control Panel

Page 4

Il. List of Tools Needed For Installation of Gun

7mm or 8/32” nut driver

10mm nut driver

electric drill

1/4” drill bit

3mm hex wrench (provided)

staple gun

small wire cutters

hammer (optional)

Page 5

lll. Installation of Gun Assembly CAREFULLY READ ALL STEPS BEFORE BEGINNING

  • Removal of Right Joystick A. Remove the control panel that the gun is to be installed into and disconnect the 15 pin and 12 pin control panel connectors. . Remove the eight (8) connectors from the right joystick assembly. . Remove the four (4) M4 cap nuts and the joystick assembly. . IMPORTANT: Reinstall the two (2) carriage bolts and cap nuts into the empty holes which are closest to the front screen side of the control panel. Be sure to save the remaining carriage bolts and cap nuts so you can install the joystick again later. installation of Gun and Holster to Control Pane! 99D

A. Push the two (2) connectors on the end of the gun cable through center hole of the holster one at a time. (See illustration 1-1) B. Pull about 6” of cable through the hole in the control panel vacated by the joystick. C. Slide the individual colored wires through the slot in the cable clamp assembly. (See illustration 1-2) D. Push the gun cable into the cable clamp assembly until it contacts the bottom, and secure the cable with four (4) M4 x 6 hex head bolts and the M3 hex wrench provided. (See illustration 1-3)

NOTE: Please keep M3 hex wrench with game for any future maintenance.

TIGHTEN HEX HEAD SCREWS SECURELY.

PUSH WIRES THROUGH SLOT

NOTE: Be careful not to damage wire insulation.
Page 6

E. Using four (4) M4 x 15 carriage bolts and M4 cap nuts, bolt the control panel in between the holster and cable clamp assembly. (See illustration 1-4)

NOTE: If you wish to add the additional security chain, see Step 6 on page 7 before continuing. Be sure that the holster is perpendicular to the control panel and tighten the four (4) cap nuts securely. F. Install the sticker tie down next to the existing tie down, near the edge of the control panel, and fasten down the excess gun wire.
  • Installation of Holster Bracket A. Fasten the control panel onto the cabinet. B. Hold the holster bracket on the bottom of cabinet front. Align the threaded holes to the slots in the holster and mark location of the four (4) square holes on bottom of cabinet. (See illustration 1-5) C. Remove the control panel and drill two (2) 1/4” holes at the locations marked.
NOTE: Choose the two (2) holes which are closest to center line of the cabinet support. (See illustration 1-5) Using two (2) M6 x 30 carriage bolts and backing plate, bolt holster bracket into place.

HOLSTER

CONTROL PANEL

BACKING PLATE

—— CENTER LINE OF

ti 1 CABINET SUPPORT

NOTE: Mark hole locations before drilling.

MS x8—™ HOLSTER BRACKET > HEX HEAD BOLTS BACKING PLATE

VS DUAL AND VS UNI 1% VS UNI CONVERSION GAME

Page 7
  • Installation of Control Panel and Harness A. Disconnect the 4 pin coin switch harness and connect the 4 pin gun power harness in between. (See illustration 1-6 A)
NOTE: Be sure to use the 4 pin coin switch harness, not the 4 pin service switch harness. . Connect either of the 1 pin connectors from the gun power harness to the 1 pin connector on the 15 pin short harness. (See illustration 1-6 B) . Connect the red 3 pin connector and the white 3 pin connector to the matching connector from the gun. (See illustration 1-6 C) . Connect the 15 pin connector to the main control harness. (See illustration 1-6 D) . Install the control panel and fasten down the control panel clamps. Fasten down the holster to the holster bracket with 2 or 4 M5 x 8 hex head bolts (depending on cabinet). (See illustrations 1-5)

mmo O @

Page 8
  • P.C. Board Modification
NOTE: Important! The game will not operate without this modification. A. Using a small pair of wire cutters, clip off the capacitors in locations C53, C61, C71 and C78. (See illustration 1-7)
CAUTION: BE CAREFUL TO CUT OFF THE CORRECT CAPACITORS ONLY.
NOTE: This modification will not affect any future V.S.-Pak games.

ooo @00 eo0000@00 eo°o°0e@00000 0 90000000 0 oO oes Me] fe] a oo

Page 9
  • OPTIONAL: Security Chain Installation
NOTE: Parts are provided to attach an additional chain between the gun and the control panel to control theft in unmonitored locations. THE CHAIN ITSELF IS NOT PRO- VIDED.

A. You should purchase approximately 33 3/4” of straight link coil chain or equivalent. After installation, the chain should be 1/2” shorter than the gun cable. B. Attach the chain to the control panel and to the gun as shown. (See illustration 1-8) C. For a better appearance, chain should also be attached to cable with two (2) metal rings as shown (not provided). (See illustration 1-8)

NOTE: Use a hammer to drive the hammer drive screw into the rivet.
Page 10
  • Installation of Alarm Sticker and Warning Notice A. Attach the alarm sticker to the holster as shown. (See illustration 1-9) B. Staple the warning notice to the outside of the backdoor of the cabinet. NOTE: Warning notice should be torn off from back cover of the manual.
  • Install EPROMS, PPU and graphics per the V.S.-Pak Instruction Sheet.

1-9

Page 11

MAIN HARNESS (]

13 [esv bc 3P-CONNECTOR (WHITE! Chee —— b 062 GUN Ass'Y

{3 sev pe

pS 45P-CONNECTOR

062-15P GUN HARNESS

3P- CONNECTOR (REDI 1 {8.COIN-7__] ;E{S-COIN-E |} COIN SELECTOR

A MAIN HARNESS (] [3 Si+sv oc

4P-CONNECTOR

‘4P-CONNECTOR

062-4P GUN POWER HARNESS

Seve) Pp OUT

1P-CONNECTOR (R)

AM

062 GUN HARNESSES

eee Cz Nintendo of America Inc.

Page 12

V. Reorder Parts List

PART NUMBER DESCRIPTION

MDSG-14-01 Gun

MDSG-11-29 Holster

MDSG-11-30 Cable Clamp Assembly

MDSG-11-32 Holster Bracket

MDSG-11-33 Bracket Plate

MDSG-41-11 062-4A Gun Power Harness MDSG-41-12 062-15P Short Harness

MDSG-63-11 3mm Hex Wrench

MDSG-11-40 Alarm Sticker

MDSG-63-15 Security Chain Retainer Kit MDSG-51-18 M5 x 8 Hex Head Cap Screw

Page 13

SEPARATE HERE - POST ON GAME.

WARNING

The gun for this game is made of a metal frame encased in rubber. It has been designed by Nintendo to prevent injury to players or damage to the video monitor and game cabinet. However, there are risks if this game is used improperly. These risks and the steps you should take to avoid them are as follows:

1. The gun could be removed from its cable by acts of vandalism and therafter misused. When the power to the game is “on,” an alarm will sound if the gun is removed from its cable or the cable is removed from the cabinet. A warning sticker alerting players to this alarm is posted on the metal holster. Replacement stickers may be obtained from any Nintendo distributor. A security chain may also be attached to the butt of the gun and anchored to the cabinet (see Instruction Manual). The game should be placed where its operation can be monitored at all times. . The gun could be mistaken for a real gun. Do not place this game where players operating it or pointing the gun may be mistaken by the police or public. THIS WARNING MUST BE POSTED ON THE BACK OF THE GAME CABINET.

NINTENDO OF AMERICA INC. REDMOND, WASHINGTON 1-800-633-3236

Page 14

Il.

GUN KIT MANUAL REVISIONS

(FOR VS. SYSTEM TABLE GUN PAKS)

Contents of Gun Kit (Revised)

Parts Name

Gun

Holster

Cable Clamp Assembly

M4 x 6 Hex Head Cap Screw

MS x 8 Hex Head Cap Screw

Holster Bracket

M4 x 15 Carriage Bolts

M4 Cap Nuts

062-4P Gun Power Harness

062-15P Short Harness

3mm Hex Wrench

Alarm Sticker

Warning Notice

Security Chain Retainer Kit

Chain Retainer G

Chain Retainer CP

Rivet

Hammer Drive Screw

Gun Kit Manual

Gun Kit Table Revisions . ea ore eee en fF

PRP PPP PP Pe Pee Remarks

Complete assembly

For Cable Clamp Assembly

For Holster Bracket

For Gun Clamp Assembly and Holster Bracket

For Gun Clamp Assembly and Holster Bracket

For Gun

For Control Panel

List of Tools Needed for Installation of Gun (Revised)

7mm or 8/32" Nut Driver

Electric Drill

3/16" Drill Bit

3mm Hex Wrench (provided)

Small Wire Cutters

Page 15

IIl.

1)

2) Installation of Gun Assembly (Revised Steps)

CAREFULLY READ ALL STEPS BEFORE BEGINNING

Removal of Right Joystick A. B. c. Remove the control panel that the gun will be installed into. Remove the eight (8) connectors from the right joystick assembly. Remove the four (4) M4 cap nuts and the joystick assembly.

NOTE: Save the four (4) M4 cap nuts so you can install the joystick again later.

Installation of Gun and Holster to Control Panel

Push the two (2) connectors on the end of the gun cable through the center hole of the holster one at a time. (See illustration 1-1) Pull about 6" of cable through the hole in the control panel vacated by the joystick. Slide the individual colored wires through the slot in the cable clamp assembly. (See illustration 1-2) Push the gun cable into the cable clamp assembly until it contacts the bottom, and secure the cable with four (4) M4 x 6 hex head bolts and the M3 hex wrench provided. (See illustration 1-3)

NOTE: Please keep M3 hex wrench with game for any future maintenance. Using four (4) M4 x 15 carriage bolts and M4 cap nuts, bolt the control panel in between the holster and cable clamp assembly. (See illustration 1-4)
NOTE: If you wish to add the additional security chain, see step 6 on page 7 (of Gun Kit Manual) before continuing. Be sure that the holster is perpendicular to the control panel and tighten the four (4) cap nuts securely.

TIGHTEN HEX HEAD. SCREWS SECURELY

PUSH WIRES THROUGH SLOT

NOTE: Be careful not to damage wire insulation.
Page 16
  • Installation of Holster Bracket

A. B.

M5 x 8 HEX HEAD BOLTS Set the control panel in place on the cabinet. Hold the holster bracket on the bottom of the cabinet. Align the slots in the bracket to the threaded holes in the holster and mark the location of the two square holes on the bottom of the control panel support. (See illustration 1-5) Remove the control panel and drill two (2) 3/16" holes in locations marked. Using the two (2) M4 x 15 carriage bolts and M4 cap nuts, bolt holster bracket into place. (See illustration 1-5)

CONTROL PANEL CABLE CLAMP ASSEN

1-4

HOLSTER BRACKET

1-5

  • Installation of Control Panel and Harness

AL Disconnect the 4 pin coin switch harness and connect the 4 pin gun power harness in between. (See illustration 1-6A)

NOTE: Be sure to use the 4 pin coin switch harness, not the 4 pin service switch harness. Connect either of the 1 pin connectors from the gun power harness to the 1 pin connector on the 15 pin short harness. (See illustration 1-6B) Connect the red 3 pin connector and the white 3 pin connector to the matching connector from the gun. (See illustration 1-6C) Connect the 15 pin connector to the main control harness. (See illustration 1-6D) Install the control panel and fasten down with the four (4) machine screws. Fasten down the holster to the holster bracket with the two (2) M5 x 8 hex head bolts. (See illustration 1-5)
Page 17

AES To coin switches

8) 1-6

Refer to Gun Kit Manual for this Step.

Refer to Gun Kit Manual for this Step.

Installation of Alarm Sticker and Warning Notice

A. Attach the alarm sticker to the front of cabinet in location shown. (See illustration 1-9) B. Display warning label (last page of Gun Kit Manual) on side of table cabinet.

Install EPROMS, PPU and graphics per the VS.-Pak Instruction Sheet.

Page 18

v. Reorder Parts List (Revised)

Part Number

MDSG-14-01

MDSG-21-29

MDSG-11-30

MDSG-21-32

MDSG-41-11

MDSG-41~-12

MDSG-63-11

MDSG-11-40

MDSG-63-15

MDSG-51-18 Description

Gun

Holster - Table Type

Cable Clamp Assembly

Holster Bracket - Table Type

062-4P Gun Power Harness

062-15P Short Harness

3mm Hex Wrench

Alarm Sticker

Security Chain Retainer Ki:

MS x 8 Hex Head Cap Screw

Page 19

GUN KIT MANUAL REVISIONS

For VS. SYSTEM” PAC- MAN” Cabinet

Il. Contents of Gun Kit (Revised)

Parts Name

Gun

Holster

Cable Clamp Assembly Cable Clamp Plate (chrome)

M4 x 6 Hex Head Cap Screw

M4 x 15 Carriage Bolts (chrome)

M6 x 30 Carriage Bolts (chrome)

M6 Cap Nuts

M4 Cap Nuts

072-4P Gun Power Harness

062-15P Short Harness

3mm Hex Wrench

Alarm Sticker

Warning Notice

Security Chain Retainer Kit

Chain Retainer G

Chain Retainer CP

Rivet

Hammer Drive Screw

Gun Kit Manual Gun Kit Pac-Man™* Cabinet Revisions

Sticker Tie Down

List of Tools Needed for Installation

10mm Nut Driver

7am or 8/32" Nut Driver

Electric Drill

1/4" Drill Bit

3mm Hex Wrench (provided)

Small Wire Cutters

Staple Gun

*Trademark of Bally Midway Mfg. Co.

-l- Ee

ee ee Remarks

Complete Assembly

For Cable Clamp Assembly

For Gun Clamp Assembly

For Holster

For Holster

For Gun Clamp Assembly

For Gun

For Control Panel

of Gun (Revised)

Page 20

III. Installation of Gun Assembly (Revised Steps)

1)

2) CAREFULLY READ ALL STEPS BEFORE BEGINNING

Removal of Right Joystick

A. B.

c. De Remove the control panel that the gun will be installed into. Remove the eight (8) connectors from the right joystick assembly. Remove the four (4) M4 cap nuts and the joystick assembly.

IMPORTANT: Reinstall the four (4) carriage bolts and cap nuts in the empty holes.

Installation of Gun to Control Panel

Push the two (2) connectors on the end of the gun cable through the center hole of the cable clamp plate one at atime. (See illustration 1-1) Pull about 6" of cable through the hole in the control panel vacated by the joystick. Slide the individual colored wires through the slot in the cable clamp assembly. (See illustration 1-2) Push the gun cable into the cable clamp assembly until it contacts the bottom, and secure the cable with four (4) M4 x 16 hex head bolts and the M3 hex wrench provided. (See illustration 1-3) NOTE: Please keep M3 hex wrench with game for any future maintenance. Using four (4) M4 x 15 carriage bolts and M4 cap nuts, bolt the control panel in between the cable clamp plate and cable clamp assembly. (See illustration 1-4) NOTE: If you wish to add the additional security chain, see step 6 on page 7 (of Gun Kit Manual) before continuing.

TIGHTEN HEX HEAD SCREWS SECURELY

PUSH WIRES THROUGH SLOT

NOTE: Be careful not to damage wire insulation.
Page 21
  • Installation of Holster

A.

B. Hold the holster in place just to the right of the coin door and mark the location of the three (3) square holes on the holster. (See illustration 1-5) Drill three (3) 1/4" holes in locations marked. Using the three (3) M6 x 30 carriage bolts and M6 cap nuts, bolt holster onto the front of the cabinet. (See illustration 1-5)

Alarm Sticker

Holster

CONTROL PANEL CABLE CLAMP ASSEMBLY

1-5

  • Installation of Control Panel and Harness

A. Disconnect the 4 pin power-in harness from the AV-Ol p.c. board and connect it to the 4 pin gun power harness. Connect the other end of the 4 pin gun power harness into the now vacant connector (P3) on the AV-Ol p.c. board. (See illustration 1-6A) Connect either of the 1 pin connectors from the gun power harness to the 1 pin connector on the 15 pin short harness. (See illustration 1-6B) Connect the red 3 pin connector and the white 3 pin connector to the matching connector from the gun. (See illustration 1-6C) Connect the 15 pin connector to the main control harness. (See illustration 1-6D) Install the control panel and fasten down with the control panel clamps.

Page 22
  • Refer to Gun Kit Manual for This Step.
  • Refer to Gun Kit Manual for This Step.
  • Installation of Alarm Sticker and Warning Notice.

A. Attach the alarm sticker to the front of cabinet in location shown. (See illustration 1-5) B. Staple warning label (last page of Gun Kit Manual) on back door of cabinet.

  • Install EPROM's, PPU and graphics per the VS.-Pak Instruction Sheet.

V. Reorder Parts List (Revised)

Part Number "Description MDSG-14-01 Gun MGSG-31-29 Holster - Pac-Man™* cabinet MDSG-11-30 Cable Clamp Assembly MGSG-31-32 Cable Clamp Plate

MGSG-51-11 072-4P Gun Power Harness MDSG-41-12 062-15P Short Harness MDSG-63-11 3mm Hex Wrench MDSG-11-40 Alarm Sticker MDSG-63-15 Security Chain Retainer Kit MDSG-51-18 MS x 8 Hex Head Cap Screw

*Trademark of Bally Midway Mfg. Co.