CATHODE RAY TOMES

Klax TM-348 1st Printing Universal Kit

Klax (version 6) (Atari Games, 1990) · Kit Manual · 64 pages · 66 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

e 4 yKfice guroPe land \ amited set vw

Page 3

Control Panel Decal

Green Button Assy Snap-Action Switch Ss StartFlip Collar (2 places) eo _ Blue Button Assy voca

‘Snap-Action Switch Starvlip Collar (2 places)

Universal Kit Installation Instructions

Page 4

Copyright © 1990 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, California 95036-1110

Printed in the U.S.A 1/90

Produced by the Atari Games Technical Publications Department. Technical Writing: Rosalind Hutton Editing and Text Layout: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner lax Universal Kit

Notice Regarding Non-Atari* Parts

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts in the game.
  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following:
  • All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Interference (EMI) ground cage, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground cage and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

Contents

Figure 2-1 1 Installation How to Use This Manual ... Cabinet Equipment Requirements Tools Required Inspecting the Ki Preparing the Cabinet for the Kit Installation Assembling the Control Panel... Connecting the JAMMA Harness. Installing the Klax Game PCB Installing the Bezel, Labels, Decals, and Attraction Assembly... Setting the Coin and Game Options. Game Play

2 Self-Test Entering and Exiting the Self-Test Select Test Menu.... Statistics .. Histograms

Sound Test Switch Test ... Complete RAM Test Complete ROM Test Alphanumerics Test Motion Object Test Color Test.. Color Purity Test. Convergence Test 2-7

3 Maintenance and Troubleshooting Video Display 3 Joystick Assembly ROMs and RAMS.

4 Illustrated Parts Lists See the list of illustrations that follows.

5 Schematics See the list of illustrations and list of tables that follows.

Glossary

Statistics Sheet

Illustrations

Figure 1-1 Assembling the Control Panel..... 1-2. Klax Kit Parts Installed in a Cabinet... 2-4

2-6

2-10 2-11 2-12 2-13 2-14

Figure 3-1

3-2

Figure 4-1 4-2

Figure 5-1

Table

Table

Table

Table 5-2

1-1 1-2 1-3 1-4

2-1 2-2

3-3

5-2 Select Test Menu Screen. Statistics Screen. First Histogram Screen. Game Options Screen. Coin Options Screen. Sound Test Screen. Switch Test Screen Complete RAM Test Screen Complete ROM Test Screen Alphanumerics Test Screen. Motion Object Test Screen Color Test Screen...... Color Purity Test Screen . Convergence Test Screen RAM and ROM Locations on the Klax Game PCB...... Maintaining the Joystick Assembly Klax Kit Parts List. Joystick Assembly . Klax Game PCB Assembly Klax Games PCB Assembly Schematic Diagram (9 sheets)... we Klax Memory Map...

Tables

Equipment Requirements Kit Contents List .... JAMMA Pin and Wire Connections JAMMA Connector and Wires. Summary of the Self-Test Screen: Game Option Settings.... Coin Option Settings... When to Run the RAM Tests Bad RAM Locations by Error Address Bad ROM Locations by Error Address .. Troubleshooting Table .. Voltage Inputs and Test Points on the PCB.. What ROM Problems Look Lik Atari Game Video Connector Pin Assignments. Screen Colors Indicating Bad RAMS . Bad RAM Locations by Error Address ..5-20 Bad RAM Type by Colored Screen....... 5-20 ROM Locations by Error Address. ........ 5-20

iii

Page 6

Safety Summary

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an electrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game. AC Power Connection. Before you plug in the game, be sure that the game’s power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT). Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.
CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required.

ABOUT WARNINGS, CAUTIONS,

AND NOTES In Atari publications, notes, cautions and warnings have the following meaning:

WARNING — Players and/or technicians can be killed or injured if instructions are not followed.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
NOTE — A highlighted piece of information.
Page 7

Chapter 1

Installation

How to Use This Manual

This manual provides information for describes the self:

installing, testing, and troubleshooting the self-test screen.

Klax™ Universal kit. The manual is divided troubleshooting and maintenance proce-

into the following chapters: m Chapter 1 dures. m™ Chapter 4 contains illustrated

describes how to install the Klax kit in your parts lists. ™ Chapter 5 contains the schematics

cabinet and the Klax game play. ™ Chapter 2 for the Klax game PCB.

Page 8

Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Cabinet Equipment Requirements

Table 1-1 lists the equipment required in the cabinet into which you are installing the Klax kit. Table 1-1 Equipment Requirements

| Equipment Video: Display: olor RGB monitor : “Specification -

‘Conttol Pane

Speaker

Coin Mechanis

Power Cord. Power supply

CAUTION Do not unplug or plug in the Klax game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Tools Required

m Two C-clamps m= Drill with a 1/4-inch drill bit, a 1 3/4-inch hole cutter (or a 1 3/4-inch chassis punch), and a 1 3/16inch hole cutter (or a 1 3/16-inch chassis punch) Phillips screwdriver Flat-blade screwdriver Socket wrench set and ratchet 1/4-20 hex wrench Wire cutters and strippers Straight edge Squeegee X-ACTO™ knife Fast-ons (if you are installing a new JAMMA harness)

Inspecting the Kit

Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the KJax kit serial number, part number and description of the missing or damaged parts, and date received.

Table 1-2 Kit Contents List

Control Panel Co Control Panel De Side Panel a

‘Orange Start/Flip B Button Colla #6. x 3/4-Inch a

Preparing the Cabinet for

the Kit Installation

  • Turn off power to the game.
  • Remove the following from the cabinet: = Old PCB). a Game harness, if it is not Japan Amusement Machinery Manufacturers Association AMMA)compatible.
Page 9

ws Control panel decals, labels, and controls. m Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals, m Video display shield, display bezel, attraction shield, and marquee.

  • Wipe down and vacuum the cabinet. Paint the cabinet, if required.

Assembling the Control

Panel

You need the following parts from the kit to assemble the control panel: m Clear cover for the control panel Control panel decal Two green buttons Two blue buttons Four snap-action switches Four start/flip button collars ‘Two joystick assemblies Twelve #10-24 x 1-inch-long carriage bolts, flat washers, and locknuts

Joystick Assy Installation

. Measure your control panel to find out what size the decal and cover should be. Cut the control panel decal and cover to fit.

  • Clamp the control panel cover to the control panel. . Drill four corner holes through the control panel and the control panel cover. Use a 1/4-inch drill bit. . Install four carriage bolts and locknuts through the holes to hold the cover and the control panel together. . Cut the holes in the cover and panel using a 1 3/16-inch hole cutter for the button holes and a 1 3/4-inch hole cutter for the joystick knob holes. Use a i/4-inch drill bit to drill the mounting holes for the joysticks. . Disassemble the control panel and the control panel cover. . Install the control panel decal on the control panel. Use a sharp knife and cut out the holes for the controls in the decal. . Install the cover on the control panel with four carriage bolts, washers, and locknuts. . Install the buttons with a plastic start/flip collar under each button. Install the blue player control buttons on the left and the green player control

Panel Cover Carriage

Flat Washer

Control Panel Decal T

Green Button Assy — Locknut

‘Snap-Action Switch S StarvFlip Collar

(2 places) eo

Biue Button Assy Locknut Snap-Action Switch StartFlip Collar (2 places)

Figure 1-1 Assembling the Control Panel

Page 10

Installation

buttons on the right. (See Figure 1-1.) Install the joysticks with the carriage bolts, washers, and locknuts,

Connecting the JAMMA

Harness

  • If your game does not already have a JAMMA harness, install the JAMMA harness in the cabinet.
  • Install the split beads on the harness as close to the connector as possible. Hold the beads on the harness with the tie wraps included in the kit.
CAUTION You must install the split beads included in the kit on the JAMMA harness to meet FCC requirements.
  • Using Table 1-3, JAMMA Pin and Wire Connections, for wiring information, connect the JAMMA harness to existing component harnesses. Use

Table 1-3 JAMMA Pin and Wire Connections Instructions o : [

Pin Wire

Conaect to the sv RIN (GND) ierninal yn the power supply. RIN, COBDER O one of the BN wires at pind;'2, A, or B.to: the 12 Same as pin 1. eS

  • Connect to the +5V terminal On ‘the | power supply. __ +SENSE terminal, connect one: ‘ofthe R res, at.pin, 3, ASV, . 4 : ‘Same a as pin 3. 5 Connect to'the 5 terminal of the
ce=12V-RTN or the 5.V RIN (GND) or leave it unconnected.

ee NOTE: if you do not have ree). ae the je mut potuer : by half. 6 ‘Connect to the +12V terminal of the power supply ce AE yout ‘coin, counter(s) fee 12V; aso ‘connect to. thes 7 5

: comect this wire to one side of the 12V coin counte:

8-BU/W.COINCIRI

: ee : Ht your counter! rau an ‘connect a wits, from Oe H

9:Not used
10.BNSPKR+

1 | Notised 12-0 RED. ——_ Attach to the video display. 13 BU “BLUE Attich to the video display.

14BK.VIDEO GND_ Attach to the video display...

15 SELF-TEST _ Use this wite if you want an external self-test switch. How er, the test Switch on the PCB. (Ifyou connect an external self-test switch, on the PCB: Connect the wire to the N.O. terminal on. the external 2 the common terminal of the switch 10 a BK/W wire (GND).

Connect to the N.O. terminal of the left coin switch, Connect th

16. : “switch toa BK/W wires. 17 Connect this wire or the one at pin 22 to the N.O. terminal is of = _ Coniect the common terminals of the switches to one of the 18 > Connect to the 'N.O. terminal of the to one of the BK/W. wites. :

  • Ar jovsrr DN Same as pin 18.
20.W/ORLTJOYSTLTSameaspin 18__
21.WXLT JOYSTRT- Same as pin 18,

LY BUTTON 2 Connect this wire or ihe o one ‘at pin v to the N, oO. terminals of ae Connect the ‘common terminals of, the switches | to one of the 23 _ W/BU Not used

24°W/V.Notused
Page 11

Klax Universal Kit Installation.

Table 1-3 JAMMA Wire Connections, Continued

~W/GY Not used

1260VeeNotused

BK/W. GND. ° 8, the power supply (if it exists) and one to the common:

‘Cohnect two of these ‘wires to the common terminals of the cont

Solder Side

ABN

_ Connect to the -5V terminal of the power suppl It 12Y RIN of the 5-V REN (GND) or feave | it unconnected.

yo aw. FE

Jv/wCOINCTR2
:Not used|

Wo SPKR- _ Not used GN. GREEN ~ COMPSYNC “GY. Service. Nor used OR RTCOIN Y/BK RT. BUTTON 1 Connect this wire or the one ‘at pin ‘ : ee the common setuinal of the switches 10 one of Y/BN “< GC Hees zen a vs

to one of the BK/W wires,

WwYRRT JOYST DN Same as’pirtV.
XY/OR”RTJOYSTIT Same as pin v.
Yo.Y/W:REJOYSTRT Same'as pin ve

}Z Y/GN

LaY/BUNot used
boWVNot ised
cY/GYNot used _
d-GY/WNot used
e€BK/W:GND
2=power supply (if it exists) and ‘One to the ‘common terminal

Connect two of these wires to the Common terminals of the

Eeeeees trobpanel.
£BK/WGND.Same as pire.”
Page 12

Installation

Table 1-4 JAMMA Connector and Wires

VIDEO GND SELF-TEST

CONT

LT BUTIN 1 u

LY JOY UP18V
LTJOY.DN19WiY/R RTJOYDN
LT JOY LT20 xXREJOYIT
LT JOY RT216¥/ RTJOY RT

AT BUTIN2 © Slaz Z| | RTBUTTN2 |

Not used23 a.| Not use

ENot used = 124 b Not used ‘Not used. 2 . 126d | GY/AW 27 | BKAW 28 fF

crimp splices or butt soldering. Also see Table 1-4, JAMMA Connector and Wires, for more information.

WARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose connections, oxidation, or a fire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Klax kit requires +5V and +12V. If -5V is available, it should be used too. Tie off any other voltage wires on the power supply besides +5V, -5V, and +12V.

1-6 There is more than one wire for each voltage in the JAMMA harness, Use more than one wire for each voltage (connecting them as described in Table 1-

  • so that the edge connector does not overload and burn.

Connecting Video Display Wires

NOTE The JAMMA harness provides only negative composite sync. If your video display requires separate positive sync, see Chapter 3 for alternative wiring.

Connect the wires designated for the red, green and blue video guns along with the sync and ground wires, according to Table 1-3.

Sounecins Coin Door Wires

Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.

  • Connect one terminal of the door lamps to one of the BK/W wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
NOTE Do not use -5V for the coin door lamps. -5Y is required for audio.

(Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.)

Connecting the Control Wires Connect the joystick harnesses and the button harnesses to the JAMMA harness according to the information in Table 1-3.

Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the video display, and the power supply. This is required for the safety of the players. This AC ground must be of #18 AWG wire or larger.

Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and -5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.

Page 13

Installing the Klax Game

PCB

  • After you have checked the power on the JAMMA connector, above, install the Klax game PCB in the cabinet. Use the nylon standoffs and four #6-32 screws in the kit.
  • Connect the JAMMA connector to the PCB.
  • Turn on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 3.

Installing the Bezel, Labels,

Decals, and Attraction

Assembly

The kit parts are shown assembled in a cabinet in Figure 1-2.

Installing the Display Bezel Find the cardboard display bezel (part no. 047463-01). Measure the size of the existing display bezel and cut the new display bezel to size, if necessary.

Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC label (part no. 039450-01) on the back of the cabinet.

Installing the Side Panel Decals Find the side panel decals. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals as shown in Figure 1-2. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.

Installing the Attraction Assembly Find the Klax attraction shield and the attraction film. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-2.

Setting the Coin and Game Options

Set the coin and game options in the self-test. See Chapter 2 for information about the option settings.

Game Play

This section of the manual describes the theme of the Klax game and the game play features. Tastallation

Introduction The tiles klank end over end down the ramp. Catch them on the paddle, or they fall in the pit. Flip them from the paddle into the bins, matching the same-colored tiles horizontally, vertically, or diagonally. Each line of colored tiles is a Klax. When you've made a Klax, you hear a fanfare.When you complete a wave, the crowd cheers. Let a tile fall in the pit, and you hear a scream as it falls in. Jf you fail to complete a wave, the crowd is disappointed. Stay alive, complete the waves and don't drop any tiles!

Catch the tiles as they come to the end of the ramp on the paddle. Flip a tile into a bin by pressing the start/flip button. Pull the joystick forward to increase the speed of the closest tile as it klanks down the ramp. Push the joystick back and toss the top tile on the paddle back on the ramp and gain a little time. The paddle can hold up to five tiles. As long as the green light is on below the paddle, you can pile more

  • tiles on the paddle. When the red light appears, you must flip at least one tile in a bin or toss it back on the ramp before you can collect any more ties. You can flip tiles into a bin as long as the green light is on below the bin. To succeed in Klax, make points and also complete each wave. Create a horizontal, vertical, or diagonal row Of at least three tiles Gust like in tic-tac-toe) in the bins to make a Klax and make points. You receive the most points for diagonals, less for horizontals and the least for verticals, When you create a Klax, the tiles in the Klax disappear to make room for more tiles in the bins. Each wave has a different task to be completed, which is shown on the To Go Meter. This task could be making a certain number of Klaxes or points or surviving a certain number of tiles. Complete the task before too many tiles drop in the pit and you complete the wave. When you complete a wave, you receive bonus points for the tiles remaining on the ramp, on the paddle, and any empty spaces in the bins. If you fail, you can start again at the same wave. Klax does not have a clock for you to race against, but as your playing time increases, the tiles klank down the ramp faster and faster. Waves When you first enter the game, you can start at wave 1, 6, or 11, Wave 1 teaches you how to play the game and use the controls. At every fifth wave you can choose to play the next wave, the fifth wave beyond, or the tenth wave beyond. Klax has five different types of waves and more than five different backgrounds. There are five waves per level, and one hundred waves to complete.
Page 14

Installation. Klax Universal Kit

Attraction Shield

Attraction Film

Side Panel Decal

Game PCB 7 Assembly Display Shield < Stand-offs #0-32 Screws

Joystick Assy

Self-Test Switch Control Panel Cover

Volume Control

Control Panel Decal Green Button Assy Snap-Action Switch Start/Flip Collar (2228) ius Button Assy

Snap-Action Switch StarvFlip Collar (2 places) Control panel in closed position Locknut

Figure 1-2 Klax Kit Parts Installed in a Cabinet

1-8

Page 15

Each time you begin a wave, the To Go meter shows what kind of Klaxes or how many points you need to accumulate to complete the wave. The different types of waves are: Klaxes To Go, which are the easiest. Just create Klaxes horizontally, vertically or horizontally. Create enough Klaxes to complete the wave before the you drop too many tiles in the pit. Tiles To Go requires you to survive a certain number of tiles. Create Klaxes in any of the three ways to collect points and to clear the bins to hold more tiles. Points To Go requires you to make a certain number of points. Create Klaxes to collect points but make diagonals, four- or five-of-a-kind Klaxes, and simultaneous Klaxes for higher points, Diagonals To Go requires you to create diagonals. Create Klaxes in any way to collect points; but only the correct number of diagonals will complete the wave, Installation

Horizontals To Go requires you to create horizontals. Only horizontal Klaxes will complete the wave; but you can create Klaxes vertically and diagonally to collect points. Game Meters You see several kinds of information on the screen. These are the: To Go Meter, which continuously calculates the number of Klaxes, tiles, points, diagonals or horizontals still required to complete the wave. The number depends on the type of wave you are playing. Drop Count, which shows the number of dropped tiles. The drop count is continuously calculated. When the number of tiles dropped is reached, the wave is over. High Score, which shows the highest score to date, regardless of the number of continues that player had. Wave Indicator, which shows what wave you are playing.

Page 16

Installation

N S

Page 17

Chapter 2

Self-Test

Use the Klax self-test to check the condi- game, each time you collect the money, or

tion of the game circuitry and controls. when you suspect game failure. This

You will see the self-test information on the chapter shows the screens in the self-

video display and hear the sound test infor- test and explains each of the tests, The mation through the speakers. You do not " screens and explanations are arranged in the

need any additional equipment to perform the self- order they appear in the self-test. Table 2-1 lists all the

test. Perform the self-test when you first set up the self-test screens and their purposes.

Page 18

Self-Test

Table 2-1 Summary of the Self-Test Screens

Entering and Exiting

the Self-Test

To enter the self-test, turn on the self-test switch on the game PCB. Exit the self-test by switching off the self-test switch in the select test menu screen. If you turn off the self-test switch while you are in any other screen, you will not exit until you return to the select test menu screen.

Select Test Menu

Choose which test or screen you want to see from this menu, shown in Figure 2-1. Move up and down the menu using the left joystick. Choose the screen by pressing the left start/flip button.

Statistics

Use the information shown on the statistics screen, in Figure 2-2, and on the histogram screens to keep track of your game use and maximize your profits. Record the information on the Klax statistics page in the back of this manual.

2-2 SELECE TEST Left Player FLIP Button ‘Then Pre

COMPLETE: ROM TE ALPHANUMERIC TEST MOTION OBJECT TEST COLOR TEST PURITY. =e

Figure 2-1 Select Test Menu Screen

The statistics are collecied from the last time the statistics were cleared. You can clear the statistics by moving the right joystick and pressing the right start/flip button at the same time. Press the left start/flip button to leave this screen and go to the histograms. m Plyr Lft Coins show the number of coins counted in the left coin mechanism. m = Plyr Ret Coins show the number of coins counted in the right coin mechanism. m Aux Coins show the number of coins credits given by the auxiliary coin mechanism. m Total Sessions shows the number of unique games played, A unique game is counted from the moment the first player started to the time the last player quit, regardless of how many times the game was continued. = 0 Plyr Min is the number of minutes the game was idle.

Sti Pise L€CCoins Piyr Ret Coins Aux Coin Total Sessions 0 Pipe Mins LPivye Mins 2 Piye Ming LPiyr Mins Piyr Mins Error Count ‘Total Coin: Ave Time/Com: Percentage Play

Move Right ST to Clear Statistics Press Left FLIP Button: for histograms

Figure 2-2 Statistics Screen

Page 19

= 1 Plyr Min is the number of minutes the game was played by one player. = 2 Plyr Min is the number of minutes the game was played by two players. mL Plyr Minis the number of minutes the game was played by the left player. mw R Plyr Min is the number of minutes the game was played by the right player. m= Error Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 6E. = Total Coins is the number of coins put into both coin mechanisms. = Avg Time/Coin is the average amount of time, in seconds, each coin counted for. m Percentage Play is the amount of time, as a percentage, that the game is played while it is turned on.

Histograms

The two histogram screens show the length of game play. The first histogram screen is shown in Figure 2-3. Clear both histograms on the second screen. Read the histogram screens frequently and record the numbers on the statistics sheet at the back of the manual. Read and clear the screens frequently. If more than 256 games are played in any one time category, then all the numbers on that screen are divided by two. If you read the screens infrequently, the number of games will always be correct proportionally, but may be incorrect numerically.

New Games

370-609 fur Press Left FLIP button. for next level:

Figure 2-3 First Histogram Screen Self-Test

Clear the histograms by pressing the right start/flip button when you are on the second histogram screen. Return to the menu screen by pressing the left start/flip button. The two histogram screens show the following information: m= New Games shows the number of seconds each new game lasted. m= Continuations shows the number of seconds each continuation of the game lasted.

Game Options

Check and select the game options on this screen, shown in Figure 2-4. To move through the options, push the left joystick up or down. Change the option enclosed in the yellow box. The factory default settings are shown enclosed in a box. To change a setting, move the left joystick right or left. To save the new settings, press the left start/flip button. This returns you to the menu screen. If you want to keep the original setting, although you have changed it, move the right joystick and press the right start/flip button. This brings back the original setting. Use the left start/flip button to return to the menu screen.

NOTE The word More appears at the bottom of the screen to indicate more options. Push the left joystick down to see the rest of the options.

The game options are explained below. The settings, with defaults, are shown in Table 2-2.

CLEAR HIGH SCORE TABLE: nO. RESTORE FACTORY OPTIONS: no DIGFICULTY RAMPING yes AUTO CLEAR HIGH SCORE: yes FBE WARNING DISPLAYED:

DISPLAY T-SHIRT AD yes ooMORE Ce Move Right STICK and Press Right FLIP restores original setting ress Lett FLIP Button to save this setting and exit

Figure 2-4 Game Options Screen

2-3

Page 20

Self-Test

Clear High Score Table lets you clear the high score table. m Restore Factory Options lets you set all the game options to the factory options or lets you use your own settings. Make sure you set this to no to use your own chosen settings. = Difficulty Ramping increases the game difficulty as the time after the last coin inserted increases if it is set to yes. m= Auto Clear High Score clears the high score table periodically if it is set to yes. = FBI Warning Displayed \ets you choose whether you want to display a “Winners Don’t Use Drugs” message and FBI logo screen during the attract mode. = Display T-Shirt Ad lets you display the Klax T-shirt screen in the attract mode. m= Sound in Attract Mode lets you turn the sound on or Off in the attract mode. = Difficulty Level lets you set choose the difficulty level of the Klax game. = Special Cost lets you choose two credits to start and one to continue, or no special cost.

Table 2-2 Game Option Settings

Coin Options

Check and select the coin options on this screen, shown in Figure 2-5. To move through the options, push the left joystick up or down. Change the option enclosed in the red box. The factory default settings are shown in green, To change a setting, move the left joystick right or left. To save the new settings, press the left start/flip button. This returns you to the menu screen. If you want to keep the original setting, although you have changed

Coin Mode 1 Coin I Credit Hight Mech Multiplier i oe unts'as | Com dows Adder No Bonus Adder

Move Right STICK and Press Right FLIP Restores Original Setting Setting and Exit

Figure 2-5 Coin Options Screen

it, move the right joystick and press the right start/flip button. This brings back the original setting. Use the left start/flip button to return to the menu screen. The coin options are explained below. The settings, with defaults, are shown in Table 2-3. ™ Coin Mode is the number of coins required for one credit. m= Right Mech Multiplier is the number of coins each coin counts as in the right coin mechanism. m Left Mech Multiplier is the number of coins each coin counts as in the left coin mechanism. m= Bonus Adder lets you choose bonus coins, no bonus, or free play.

Table 2-3 Coin Option Settings

Page 21

Sound Test

The sound test indicates the condition of the sound effects circuit on the game PCB. The sound test screen appears in Figure 2-6.

SOUND TEST

Number of Sounds

Sound # i

Press Left Flip Batton to hear sound Move Lett Joystick to select sound Press Hight FLIP button to retin to menu

Figure 2-6 Sound Test Screen

Use the right joystick to select the sound and press the right start/flip button to listen to it. Pressing the left start/flip button returns you to the menu screen.

Switch Test

The switch test screen is shown in Figure 2-7. Test the coin mechanisms, buttons, and joysticks. As you use the control, a red box appears around its name on the screen. If the red box does not appear, check the connections, switches, and mechanism. Press the left and right start/flip button to return to the menu screen.

Press buttans and move sticks

in Switch: Right Coin Switch in ne Right Blip. ‘Bett Joputick RK ae doyetiek BR Lett Jo: ck L Right i Right 38 Right Jo:

Press Left FUP and Right FLIP Button to retian to menu

Figure 2-7 Switch Test Screen Self-Test

Pressing the left and right auxiliary coin switches tests the coin switches. Pressing either of the left start/flip buttons causes a box to appear around the words Left Flip. Pressing either of the right start/flip buttons causes a box to appear around the words Right Flip. Moving the left joystick causes a box to appear around the direction name when you move it right (R), left (L), down (D), and up (U). Do the same for the right joystick. If a box does not appear around a joystick test direction, check the switch connections and the switch in that position.

Complete RAM Test

Use this selection screen, shown in Figure 2-9, to choose which RAM test you want to perform. Use the different tests according to Table 2-4. If you get an error in any of the RAM tests, see Table 2-5 for more information. If you have serious RAM problems you may see only a colored screen. If this happens, see Table 3-5.

eid RAM Gooping) Or Object. RAM (looping) Color RAM Goopings AL TAM (re-star Exit RAM tests:

To select, move Left STICK up or dawn Then press Left FLIP Button

Figure 2-8 Complete RAM Test Screen

Table 2-4 When to Run the RAM Tests

Problem Playfield ig erratic Or looks wrong. Motion objects are erratic Motion or not working ‘properly. Colors look wrong.*

Page 22

Self-Test

To choose a test, move the box to the test name and press the left start/flip button. Return to the menu screen by moving the box to the words Exit RAM Tests, then press the left start/flip button to return to the menu screen.

Table 2-5 Bad RAM Location by Error Address

Error "es RAM Location

Address“>HighLow >
3FOO00©re aX2
3E00001yNone

Complete ROM Test

The ROM test screen is shown in Figure 2-9. The 0K and 20K information appears. If the game has no ROM errors, you immediately return to the menu screen. If the game does have ROM errors, the ROM test screen will remain until the ROM error information is complete, as shown in Figure 2-9. Press the left start/flip button several times to see information about the ROM errors. The ROM error test takes a few seconds. See Table 2-6 for the location of the ROM errors. Press the left start/flip button to return to the menu screen. If you think you have a ROM error, but the screens show no messages, see Table 3-3 for information about the locations of various ROM functions.

OK-H6:OK-L23B2
20K - H.STF20K -L8936

ROM at 000000 error UL 40B3 ROM at 020000 error UL 55D at-008000 error U T0002

04 DEC 1989 17:1

Figure 2-9 Complete ROM Test Screen.

Table 2-6 Bad ROM Location by Error Address

Error RAM Location

Address High Low

00000073NIN’ =.
0200003K1K

2-6

Alphanumerics Test

The alphanumerics test, shown in Figure 2-10, checks the condition of the alphanumerics in the game. You can reverse the alphanumeric display by pressing the right start/flip button. If you see an error on the screen, check the EPROMs at 12U, 12W, 12X, 12Y, 17U, 17W, 17%, and 17Y. Press the left start/flip button to go to the menu screen.

Figure 2-10 Alphanumerics Test Screen

Motion Object Test

The motion object test screen, shown in Figure 2-11, tests the movement and color of various game objects. Choose an object with the left start/flip button. Use the left joystick to move the object. Press the left and right start/flip buttons simultaneously to go to the menu screen.

Figure 2- 11 Motion Object Test Screen

Page 23

Color Test

This test indicates the dynamic range of the video display color circuit. The screen is shown in Figure 2-12.

Figure 2- 12 Color Test Screen

The left side of the screen shows a grey scale with black on the left and white on the right. The right half of the screen should be red, green, and blue from top to bottom, each with a color scale from dark to bright, left to right. If the screen does not match this description, adjust the video display as described in the video display manual. Return to the menu screen by pressing the left start/flip button.

Color Purity Test

The color purity test has five screens. Each screen is a rectangle of color. The first screen, shown in Figure 2-13, is red. The other screens, which you can see by

Figure 2-13 Color Purity Test Screen Self-Test

pressing the right start/flip button, are green, blue, white, and gray. These screens show the adjustment of the color purity of the video display. Each screen should display a rectangle of color, with no curving at the corners, no unevenness of color, and no lines in the display. If the screens are not correct, adjust the video display as described in the video display manual. Return to the menu screen by pressing the left start/flip button.

Convergence Test

The convergence test has three screens: first white, then violet, and finally green. The white screen is shown in Figure 2-14. To see the violet and green screens, press the right start/flip button. Press the left start/flip to go to the menu screen. Check the following on the screens: a The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel. m The convergence of the lines on the violet and white screens should be within 2.0 mm. If these screens do not meet these criteria, adjust the video display as described in the video display manual.

Figure 2- 14 Convergence Test Screen

Page 24

Self-Test

N

2-8 S

Page 25

Chapter 3

Troubleshooting and Maintenance

This chapter contains troubleshooting ta- the last table describes ROM-caused problems

bles and repair procedures for your Klax with specific ROMs to check and replace.

game. The chapter has two parts. The The last part of the chapter has informa-

first part contains three troubleshooting tion about connecting the video display if

tables. The first table has general trouble- it requires separate positive syne, repair informa-

shooting information, the second table contains the tion for the joystick assembly and locations of the

voltage levels and test points on the game PCB, and RAMs and ROMs on the game PCB.

Page 26

Maintenance Klax Universal Kit

Table 3-1 Troubleshooting Table

‘Check the wiring to the coin mechanis ‘2. Check the voltage to the + side of the mechanism,

  • Test the ‘coin fnechnabisms with th sound test scr Coin Mechanism Problem _ Game Play one ce

4 Check What ROM Pr ‘oblems. Look. Tike, Table = -3, for specific ROM S

‘Figure 3-1 for ROM locations, | 1. Has the joystick been’ lubricated with white liu fur greas © 2-Check the harness and connectors. se ‘3. Check ‘the switches on the joystick. ee

  • 4.1f you took the joystick apart, have you reassemble

5. Make sure all the parts ¢ on the 30) tick are ein Bood Te]

Joystick Problem:

a 1s the ‘speaker wolune tured up? : . Check the voltage on the: JAMMA ‘connector 3.Check the wiring from the PCB ‘to the ‘speaker Sound Problem —

  • Replace the spake > Display Problem _ oe _ Syne problems." Does your r display need separate Pov sync? See the Wi . : section in. this. chapter: / Is the game plugged in? Is the game turned on? Are the connections good? Is the line fuse good? i Is the display. brightness turned up? — Are the solder connections on the line filter and transfor: ‘Is the JAMMA connector on the PCB tightly connected? . Check all of the items below. If you answer no to any question, yo ‘have a problem with the video display, not with the game | citcuitry. See you “video display service manual. B ee

- - a..Do you have power to the Video ‘display?

'b. Are the video ‘display’s filaments lit: : ¢: Do'you have high voltage to the vidéo display? =

  • Is the voltage level to the video display PCB correct? @ower voltage i is 100 VAG

‘or T10 VAC, depending on the type of video display, Video: See es

_ 103.5 Volts.)

  • If the level is not correct, check the connectors and the | Only a colored screen appears. You probably have a serious RAM problem. See Table 3 Screen is‘dark, SIRU RON

oe oO Bad RAMS.

Display area wavers or=A, Do you have oltage to the video display PCB? i
is too. small.=© 2eDo you have high voltage to the video display?

_ Picureiswavy, 4. Is the monitor ground connected to the monitor?

i:e-2. Are the sync inputs connected properly? Does yourneed a spate positive

: oe sync? See the Video Display Sync Problems section in this chapter: Picture is upside down, _ Switch the horizontal or vertical yoke wires on the display. = ‘Convergence, purity Use the screens in the ‘self-test to adjust the video display. or color problems. : . : a Picture is not centered,

3-2

Page 27

Table 3-2 Voltage Inputs and Test Points on the PCB Maintenance

Video Display

Sync Problems Some video displays cannot use the composite negative sync that is on the JAMMA connector. The Klax kit includes a standard Atari Games video connector (located at 12A) that provides separate positive sync. Refer to Table 3-4 and make the appropriate connections for your video display. For other problems, see the video display manual that came with your game.

Table 3-4 Atari Games Video Connector Pin Assignments

Horizontal Shifting

If you cannot center the picture on the display horizontally as described in your video display manual, you can shift it by altering the Klax game PCB.

  • Remove the resistor at R102.
  • To shift the display to the right, add a resistor of less than 100Q (or a wire) at location R105.
  • To shift the display to the left,, add a resistor of less than 100Q (or a wire) at location R103.

Joystick Assembly

The joystick is shown in Figure 3-2. If you want to repair the joystick, disassemble it by removing the E-ring at the bottom of the shaft and removing the screws.

Table 3-5 Screen Colors Indicating Bad RAMs

3-3

Page 28

Maintenance Klax Universal Kit

R A M: only a colored screen and cannot enter the self-test,

ROMs and Ss see Table 3-4, If you have a ROM problem, see Table

If you have think you have bad ROMs or RAMs, pre- 3-3. For the location of all the ROMs and RAMs on the form the ROM or RAM test in the self-test. If you see game PCB, see Figure 3-1.

Motion Object RAMs Graphic ROMs Playfield RAMS

136075-1001

i 136075-XX06 Ne AR F220 DOHA Cc

136075-1000 136075-1016

Figure 3-1 RAM and ROM Locations on the Klax Game PCB

3-4

Page 29

Maintenance

99-215025 1.5° Black Joystick Krab and Shaft

99-215026 Flat Washer

175-5112B 99-215022 Mounting Screw Hub Mounting (4 places) Plate 6

99-215018 850" Dia. Spring

\ i \ i

i \ i

i 99-215020 4-Way Microswitch Mount

99-215011 Assembly Screw (4 places)

99-215017 99-215010 187" Gold Microswitch : Microswitch Mounting Screw (8places)

99-215015 E-Ring

Figure 3-2 Maintaining the Joystick Assembly

Page 30

Maintenance Klax Universal Kit

N O T E )

3-6

Page 31

Chapter 4

Illustrated

Parts Lists

This chapter provides information you

need to order parts for your game.

Common hardware parts, such as screws,

nuis, washers, and so on usually are not

listed in the parts lists. The parts lists (except

for the PCB parts lists) are arranged alphanumerically

by Atari part number. All A-prefix numbers, which are

assemblies, come first. Next are part numbers with six

numbers followed by a hyphen (000598- through

201000-), Ending the list are part numbers with a two-

number designation followed by a hyphen (00through 99-). The PCB parts lists are

arranged in alphabetical order by compo-

nent. Within each section the parts are

arranged numerically by part number.

When you order parts, give the part number, part

name, the number of this manual, and the serial

number of your game. With this information, we can

fill your order rapidly and correctly. We hope this will

create less downtime and more profit from your

games. Atari Games Customer Service phone numbers

are listed on the inside front cover of this manual.

Page 32

Illustrated Parts Lists Klax Universal Kit

Figure 4-1 Klax Kit Parts List A047620-01 C

Part No.DescriptionPart No.Description
A046501-01JAMMA Harness Assy171057-0034-Way Joystick Assy
A047441-01Klax Game PCB Assy175014-1040#10 Flat Washer
038158-01Product I.D. Label177010-240 — #10-24 Hex Polymer Locknut
039450-01FCC Compliance Label178032-002Wire Wrap
047205-01Attraction Shield178237-005Blue Button Assy
047209-01Control Panel Cover178237-006Green Button Assy
047590-01Control Panel Decal178265-001—_L-Style Nylon Standoff
047594-01Side Panel Decal178283-002Orange Start/Flip Button Collar
047595-01Attraction Film With Graphics72-6612S#6 x 3/4-Inch-Long Pan-Head Screw
047621-01Bezel With Graphics75-5112B#10-24 x 3/4-Inch-Long Black Carriage Bolt
141026-001Split Ferrite BeadTM-348Klax Universal Kit Installation Instructions

160044-001 —Snap-Action Switch

4-2

Page 33

Tlustrated Parts Lists

99-215025 1.5" Black Joystick Knob and Shaft

99-215026 Flat Washer

1475-51128 99-215022 Mounting Screw Hub Mounting (4 places) Plate

99-215018 .850" Dia. Spring

99-215027 Actuator

99-215020 4-Way Microswitch Mount 99-215011 Assembly Screw (4 places)

99-215017 Z 99-215010 187" Gold Microswitch Microswitch (4 places) 4 Mounting Screw (8 places)

99-215015 €-Ring

T Figure 4-2 Joystick Assembly 171057-003

Page 34

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 35

Illustrated Parts Lists

Klax Game PCB Parts List A047441-01 D

Designation _ DescriptionPart No.Designation _ DescriptionPart No.
Integrated Circuits1Integrated Circuit, 7418245137134-001
1KIntegrated Circuit, EPROM136075-1007128Integrated Circuit, MOB137593-001
INIntegrated Circuit, EPROM136075-1005.12UIntegrated Circuit, EPROM136075-1011
18, 1UIntegrated Circuit, 74F373137575-00112xIntegrated Circuit, EPROM136075-1012
2AIntegrated Circuit, 7415174137122-001
13E, 13}Integrated Circuit, 74HCT273137655-001
2BIntegrated Circuit, 741832137019-001BLIntegrated Circuit, 74F74137436-001
28,2U _ Integrated Circuit, 74F244137502-00114BIntegrated Circuit, OTP136075-1015
2X, 2Y _ Integrated Circuit, RAM,137535-00415E, 15FIntegrated Circuit, 74F260137570-001

8KXB, 100 nsec

3KIntegrated Circuit, EPROM136075-1008«15KIntegrated Circuit, 74F157137494-001
15MIntegrated Circuit, 74F20137530-001
3NIntegrated Circuit, EPROM136075-100617FIntegrated Circuit, 7406137052-001
38, 3U _ Integrated Circuit, 74F378137612-00117KIntegrated Circuit, 7418174137122-001
4AIntegrated Circuit, 74LS257137136-001
5BIntegrated Circuit, 7418197137240-00117™MIntegrated Circuit, 741586137079-001
17PIntegrated Circuit, LB137536-001
scIntegrated Circuit, 68000137289-003,17R, 17T _ Integrated Circuit, SOS137550-001
5KIntegrated Circuit, 741874137023-001170Integrated Circuit, EPROM136075-1009
SLIntegrated Circuit, 7418138137177-001
5NIntegrated Circuit, 74F257137611-001177Integrated Circuit, EPROM136075-1013
17%Integrated Circuit, EPROM136075-1010
5R,5UIntegrated Circuit, 748253137574-00117Integrated Circuit, EPROM136075-1014
6AIntegrated Circuit, 7418257137136-00118BIntegrated Circuit, TDA2030137301-001
OEIntegrated Circuit, EEPROM137399-300
owIntegrated Circuit, GALIOV8 A136075-100418CIntegrated Circuit, LM324137582-001
18KIntegrated Circuit, 74F74137436-001
7BIntegrated Circuit, 741808137012-00118MIntegrated Circuit, GALL6V8 A136075-1001
7LIntegrated Circuit, 74F00137327-00119KIntegrated Circuit, 74F157137494-001
7NIntegrated Circuit, 74F32137486-001
8R, 8UIntegrated Circuit, 74F253137574-00119MIntegrated Circuit, 74F04137437-001
swIntegrated Circuit, GALI6V8 A136075-1002Ca

Sa ipacitors

zeIntegrated Circuit, 74F20137550-001C2-C16Capacitor, .1 JF, 50V, Ceramic-—-'122002-104
DyIntegrated Circuit, 7418244137038-001ci7Capacitor, .001 HF, 50 V, Ceramic122002-102
oLIntegrated Circuit, 741802137042-001C18-C20Capacitor, 100 pF, 100 V, Ceramic122016-101
o2:itp.i122002-:
oNIntegrated Circuit, 741804137009-001a1Capacltor, 001 HE, 20 V; Cecarntemacste
9R, 9UIntegrated Circuit, 74F253137574-001€22-€29Capacitor, 1 UR, $0 V, Ceramic122002-104
owIntegrated Circuit, GALIGV8 A136075-1003C39Capacitor, .001 UF, 50 V, Ceramic122002-102
oy.Integrated Circuit, SOS137550-001C31Capacitor, 22 UF, 35 V, Electrolytic—124000-226
C32CcitZCerami-224
108Integrated Circuit, 7418163 A137114-001eapacltcr, .22 Wr, 50'V,Ceramic122017
10)Integrated Circuit, 74F374137420-00133Capacitor, .1 HF, 50 V, Ceramic122002-104
10LIntegrated Circuit, 74F175137498-001
iONISnutaa34Capacitor, 470 IEF, 25 V,123003-477
integratedCircuit, 74132137019-001Electrolytic, Radial
:ve.
10WIntegrated Circuit, 74F273137610-001,,,
1BIntegrated Circuit, 74F138137521-001‘;
=38Capacitor, 100 pF, 16 V, Electrolytic 124008-107
1cIntegrated Circuit, GALI6V8 A136075-1000C39.¢41Capacitor, .1 WF, 50 V, Ceramic122002-104
—c42Capacitor, 47 pF, 25 V, Electrolytic—124009-476
MEIntegrated Circuit, 74F00137327-001,OV Ceramic122015
1Integrated Circuit, RAM,137534-0018Capacitor, .0068 HF, 50V, Ceramic122015-682
2KX8, 35 nsec.a

y 270 pF, 100 V, 2016-271

1Integrated Circuit, 74F04137437-001eCpani 2 ng Be Cane ened
QEIntegrated Circuit, 7418374137144-001cisCapacitor 270 pF, 100, Ceramic122016271
Page 36

Illustrated Parts Lists Klax Universal Kit

Klax Game PCB Parts List, Continued A047441-01 D

Designation—_DescriptionPart No.Designation _ DescriptionPart No.
47Capacitor, .1 UF, 50-V, Ceramic_-122002-104RO7, ROSResistor, 1 K Q, #5%, 1/8 W110027-102
C48Capacitor, 180 pF, 100 V, Ceramic — 122016-181R70Resistor, 10 Q, +5%, 1/8 W110027-100
C49, C50Capacitor, .1 uF, 50-V, Ceramic122002-104R71Resistor, 20 K Q, 45%, 1/8 W110027-203
51Capacitor, .033 UF, 50'V, Ceramic120015333R72, R73.Resistor, 1 M Q, 45%, 1/8 W110027-105
52Capacitor, 100 pF, 100 V, Ceramic — 122016-101R74, R75Resistor, 470 Q, +5%, 1/8 W110027-471
53Capacitor, 39 pF, 100 V, Ceramic122016-390R76Resistor, 1 K Q, 45%, 1/8 W110027-102
C56-C112 Capacitor, .1 UF, 50 V, Ceramic122002-104RIBResistor, 2.2 K Q, +5%, 1/8 W110027-222
DistesR79Resistor, 43 K Q, 45%, 1/8 W110027-432
CRI, CR2 Diode, 1N4001131048-001.
CR3, CR4_Diode, MV5053, Light Emitting131027-002R81, R82_Resistor, 1 K 2, 15%, 1/8 W110027-102
CRS, CRG Diode, 1N4001131048-001R88Resistor, 470 Q, £5%, 1/8 W110027-471
CRTDiode, MV5053, Light Emitting131027-002R84Resistor, 1 K Q, £5%, 1/8 W110027-102
CR8Diode, 1N4001131048-001R86Resistor, 2.2 K Q, +5%, 1/8 W110027-222
InductorR87Resistor, 4.3 K Q, +5%, 1/8 W110027-432
LiInductor, 100 WH141024-001R89Resistor, 10 Q, +5%, 1/8 W110027-100
‘TransistorsR90Resistor, 100 Q, +5%, 1/8 W110027-101
Q1-Q3Transistor, 2N5306133033-001ROLResistor, 10 2, +5%, 1/8 W110027-100
Q4-Q7Transistor, 2N3904133041-001
resistorsR92Resistor, 1 K Q, 45%, 1/8 W110027-102

i + z

R10, RILResistor, 470 Q, 45%, 1/8 W110027-471RodResistor, 2.2 K Q, £5%,8 Wpall
;R95Resistor, 4.3 K Q, +5%, 1/8 W110027-432
aedResistor, 1K, 259,8 W110027-102ROT, ROBResistor, 100 , +5%, 1/8 W110027-101
RI3-RI7Resistor, 470 Q, 45%, 1/8 W110027-471;eeyea,
R1S-R21Resistor, 1 K Q, 45%, 1/8 W110027-102R99, R102 Resistor, 10 ©, 45%, 1/8 W110027-100

is + s

R22, R23_Resistor, 470 2, 5%, 1/8 W110027-471R108Resistor, 10 2, 596, 1/8 Waie 18
;R109Resistor, 1 K Q, 45%, 1/8 W110027-102
R24Resistor, 0 Q, #5%, 1/4 W110005-001j
:R110 —_ Resistor, 68 , #5%, 1/8 W110027-680
beResistor, 15 K 2, £59, 1/8 W110027-153R111, R112 Resistor, 10 K Q, 45%, 1/8 W110027-103
R26Resistor, 1.5 K Q, 45%, 1/8 W110027-152,yare

j ;

R27Resistor, 220 Q, $5%, 1/8 W110027-221aResistor, 240 0, £5%, 1/8 W110027 241
fosPoventseieter107m, ver139020.105R114, R115 Resistor, 10 Q, 45%, 1/8 W110027-100
cenaa.R116, R117 Resistor, 1 K Q, 25%, 1/8 W110027-102

With Knob

R29, R30Resistor, 1 K Q, 45%, 1/8 W110027-102.
,istor, 1 KQ,£5%,RP2-RP4Resistor, R/2R118016-001
R31Resistor, 240 2, $5%, 1/8 W110027-241RPS, RP6Resistor, 4.7K x9, +5%, 1/8 W,—_-118010-472

SIP i

R32-R34__Resistor, 1 K Q, 45%, 1/8 W110027-102(10 Pin)
R35Resistor, 470 Q, 45%, 1/8 W110027-471Crystal
R36-R40Resistor, 1 K Q, 5%, 1/8 W110027-102x1Crystal, 14.318144000-004
R41-R44—_Resistor, 470 , 45%, 1/8 W110027-471Sockets

Socket, 20 Pin, .300" 179259-020

R45-R51_—_Resistor,1K Q, +5%, 1/8 W110027-102Sockei, 24 Pin, 300"179259-024
R52Resistor, 20 K Q, #59, 1/8 W110027-203Socket, 28 Pin, .600”179257-028
R53Resistor, 100 K Q, 45%, 1/8 W110027-104Socket, 32 Pin, .600"179257-032
R54Resistor, 1 K Q, £5%, 1/8 W110027-102

Socket, 40 Pin, .600" 179257-040

R55, R56Resistor, 20 K Q, 45%, 1/8 W110027-203Socket, 64 Pin, 900"179256-064
R57Resistor, 1.5 K Q, #5%, /8 W110027-152Socket, 84 Pin, PLCC179237-084
R58Resistor, 3.3 K Q, 45%, 1/8 W110027-332Miscellaneous
sistor,1.9110027-152
Roo,Resistor,1.5 6.0, 5% V8°SW1Switch, Slide, Spat160040-001
.GND1-GND3 Test Point179051-001
ROO-R62Resistor, 20 K Q, 45%, 1/8 W110027-203;
R63Resistor, 47 K 2, 45%, 1/8 W110027-473OO1HS1Heatsink, TDA2030178190-032
R64Resistor, 0 Q, +5%, 1/4 W110005-001
RES, ROSResistor 10 0, 2580, 1/8 W1002-100Connector, 2 Ckt, Header, .100 Ctr179048-002

Connector, 11 Ckt, Header, 100 Ctr_ 179118-011

4-6

Page 37

Chapter 5

Schematic Diagrams

About this Chapter...

This chapter contains the schematics for Lists.) The memory map and the faulty

your Klax Universal Kit.™ The Klax RAM and ROM tables are shown at the

Game PCB schematic has nine pages. (The end of this chapter. The Klax game does

assembly drawing and parts list for the not have an audio PCB.

game PCB are shown in Chapter 4, Mlustrated Parts

Page 38

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 39

JAM-3>— JAM-4 >— JAM-C>— JAM-0

JAM-4 JAM-2 >— JAM-8 >—4 JAM-B >— JAM-EE >—+ JAM-FF >—+ JaM-27 >— J8M-28 >—

Figure 5-1 Klax Game PCB Assembly Schematic Diagram, +30 Sut 7 Lege 588 au

Nog cNDL GNg3 ct gprs tf ‘0 at cSt copys iL C35 copty nt aeena/,) et C37 copr2

= ae vL

#32 SELFTEST » jay-15 R47 St lege S-TEST oo t ak

Sheet 1 of 9 047438-01 D Schematic Diagrams

SI/O

Page 40

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 41

e* NOT STUFFED.

#2 /aUORES #3 — /PcMRes Fs

R// rea cif) — sre US32

wee /SHITCH

T/O

Figure 5-1 Klax Game PCB Assembly Schematic Diagram, Sheet 2 of 9 047438-01 D Schematic Diagrams

SAMAJ

Page 42

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 43

271024A 2719240 27102z4a

ame NOT STUFFEO IF SLAPSTIK IS USEO.

Bs14 S13

271024 2710248 2710246

7PCM /PRR fiw ssie geo 7am /wooc 7UNLOCK /EEPROM

NOTE : USE 16L8 IF SLAPSTIK IS NOT USED.

Figure 5-1 Klax Game PCB Assembly Schematic Diagram, Sheet 3 of 9 047438-01D Schematic Diagrams

Page 44

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 45

ron om W//R Ls32 120 15K

7992030 baa Schematic Diagrams

c32 nee

acng—————> JAM

ca4 os JAM-10, <— 470/25V CSPKR+)

R27

C33 cL

CSPKR~)

DTACK Fe 7ecn ——=+ _

og_ttFeeoLS86“omesaa > $$_‘7.
70sane 2220TarlexLalaap

NO Lous cyr Lees Lae Fieosv 3 Re

  • > qupx-1 *12V 5 punx-2 FR Rosa AGNO _y aupx-3 AUDHP _s auox-4 SpPt eno
AUX _> auox-sAUX2 _y eunX-6a5 4cra
GND _> pyDx-7AGND _» aunx-8=MvS0S3

07 _yauox-9 78UX _y punx-10

GND _y aupx-4496 _ypunx-12ie

95 _>auox-13 GND _> aunx-14 GNO _»aupx-15 2 Saunx-16 YE ” 93 _yaupx-17 GND _SpuDx-18 JAM-35 GND _yaupx-19 02 _yaunx-z0 01 _yauox-21 GND _>qunx-22 GND _y quox-23 00 _yauox-24 2H _y aupx-25 4H _yauox-26 MAL _yeupx-27 GND _s puox-28 GND _spuox-24 /SINT _y aupx-30 (MINT Seupx-34 GND _Seuox-32 GND _> Auox-33 S-TEST _ypupx-34 WR _Spupx-35 GND _>qunx-36 GND _y aupx-37 7BUDRES _y aupx-38 *5V _yeupx-34 +54 _yaupx-40

Figure 5-1 Klax Game PCB Assembly Schematic Diagram, Sheet 4 of 9 047438-01 D

5-9

Page 46

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 47

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 48

Schematic Diagrams

MCKR

/MCKR

zp 23L m—izlo * als RCLOCK CLK | ss ce vot FCLOCK BLANK ON

F7u 3 S42

Se RCLOCKS 320 Fou

neca—iip >s4___#f wet pes R80 usee re a sv

19 SK Pals

cx a2 /YINT

Ls74 [23

/VACK

+sy

| 32 /PFHST — #3 /PPRA

70.0.0D3 3 pt—rprHELANK
/uSNCsg g feRCLOCKB,
4H8) * = feLink
2H~32__pyaso
1H————38___pyass
MCL32/wog-csvRea

co CLK

5-12

Page 49

Klax Universal Kit Schematic Diagrams

MOB fazs | 128g ate vec itd vec Rio 4 vec AAS as] oN Ata) on rg] CN Aas] CN ALO] CN Ra Aa) vois ar vole Ae} voi3 AS voz a vor. al vote aa vos | vos aa vor Prva vos pseu! vos ‘SRLO} vos waToH| vos. HeFLIP vO2 LORD-L8) vos Hee yoo Pet He?! HP6 ATlLatswe HPs! HM = Hea! wpe /VBLNRES ha HPO) mo-cre —2ro-cre mares ymoa-cs——*4cs_— rants ont /SLIP sure mara! VBLANK sor 48d vecank moar328 /PFHST —25)prv-cux noarz 48 prarse noars © => woata $3 7 PFT?) PrATs . PrATS| rd Peary St prar3S2 PFS7 PFS6 PFSS Luce wesPFAraS— PFS

Figure 5-1 Klax Game PCB Assembly Schematic Diagram, Sheet 6 of 9 047438-.01D

5-13

Page 50

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 51

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 52

Schematic Diagrams

(NUKE /CUWE

RUTH 1e0e

/CTIME CTIME

A FCLack 3) RAMCLK FCLOCK

THEL THEO

REO

yat3———8 vate ———SHlore MATE MATO iY mso3 { mms02 ish io MSOL ae misao

MCKR:luz
  • a CC "001 ——F} 3 git mors a 7MORO /.30FF 4 28 a
78033ra
7msD2:Ea MEO

mmsDt noc soo 2 /LB-CLR

5-16

Page 53

11E 2Kx8/35

FOO Schematic Diagrams

/CTIME

VOUT

Figure 5-1 Klax Game PCB Assembly Schematic Diagram, Sheet 8 of 9 047438-01D

25a azReso

i aly ait RY. oS 2 R3. 9G ane R2.

3assRi.
2ghtecs

Dox read a ce iF

Pat oa oak cz

iaecL
ioaltes
oaeae

lo G abs gg i} ae a2. * Poxseeh—— 8

5-17

Page 54

Schematic Diagrams Klax Universal Kit

7HSTNC

/NSYNC

/PHSYNC

Reese? $$ HS NC op Ride "* 10 |

tlaise!f20Riour* |
slo © alseR102ae |
whe 5 aksLTa0Rios"

alo = az R100 °* ag]

slols10Ri03°*|

2H +5y ee NOT STUFFED.

5-18

Page 55

Schematic Diagrams

22k ROBee a GREEN _y, jam 47K engage

Rad EEN syip-4

VID-5

RG

Figure 5-1 Klax Game PCB Assembly Schematic Diagram, Sheet 9 of 9 047438-01D 2.2K RIG e8 ae —SeE_> sam-13 47K anaaoe Q) Raa \s vi0-6

R98 C4: 100 $h8er

y1D-7

\____> jam-24

B

Page 56

Schematic Diagrams

5-20 Table 5: 1 Bad RAM Locations by Error Address

Page 57

Schematic Diagrams

KLAX Memory Map

68000 MEMORY-MAPADDRESSR/WDATA
Program ROM000000~05FFFFRD[15:0]
Program ROM SLAPSTICK058000~05FFFFRD{15:0] (programmable)
EEPROM0E0001~OEOFFFR/WD{7:0] (odd bytes only)
UNLOCK EEPROMLPxXxxwW
Watch Dog2E0000wxx (128 msec. timeout)
Color RAM Motion Object3E0000~3E03FER/WD[15:8]
Color RAM Playfield3E0400~3E07FER/WD[15:8]
Playfield picture RAM3F0000~3FOEFFR/WD[15:0]
MOB config3FOF00~3FOF70R/WD[15:0]
SLIP pointers3FOF80~3FORFFR/WM.O. link pointers
Playfield palette RAM3F1000~3P1FFFR/WD[11:8]
Motion Object RAM3F2000~3F27FFR/WD[15:0]

(Link, Picture, H-Pos, V-Pos, Link... etc.)

Working RAM3F2800~3F3FFFR/WD[15:0]
Player 1 Input (left)260000RD[15:12],D8 Active lo
Player 2 Input (right)260002RD{15:12],D8 Active lo

D flip D12: right D13: left D1l4: down D15: up

Status inputs260000RD11,D1,D0

DI coin 1 (left) Active lo Di: coin 2 (right) Active lo Dll: VBLANK Active hi

Status inputs260002RD11,D1,D0
DO:spareActive lo

Di: Service Active lo Dll: Self-test Active lo

LATCH260000wWD{12:8]

D8: ADPCM Chip Reset (active lo) D9: Spare D10: Coin Counter 2 (right) Dll: Coin Counter 1 (left) D12: spare D13: Color RAM bank select

NOTE: RESET clears this latch
4ms Interrupt ack.360000Wxx
ADPCM Chip270000R/WD[7:0]

Figure 5-2 Klax Memory Map

5-21

Page 58

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 59

Klax’ Statistics Sheet

Statistics Screen

Plyr 0 Coins: ___0 Plyr Mins:L Plyr Mins:Error Count:
Plyr 1 Coins:1 Plyr Mins:R Plyr Mins:Total Coins:
Total Games2 Plyr Mins:Percentage Play.

Histogram Screens Histogram 1 Histogram 2 New Games Continuations

O- 59__ 0- 59 60- 89. 60- 89. 90-119. 90-119. 120-149____ 120-149___ 150-179, 150-179, 180~209. 180-209. 210-239 210-239. 240-269. 240-269. 270-299. 270-299____ 300-329___ 300-329____ 330-359. 330-359__ 360-389. 360-389___ 390-419. 390-419. 420-449. 420-449__ 450-479 450-479. = 480-509. 480-509___ 510-539. 510-539. 540-569___ 540-569. 570-599__ 570-599__ 600 & 600 & up up

Page 60

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 61

AC Alternating current; from zero it rises to a maximum positive level, then passes through zero again to a maximum negative level.

ACTIVE STATE The true state of a signal. For example: The active state for is low.

ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER: A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is ap-

plied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating a coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as 1 or 0. BLANKING Turning off the beam on a cathode-ray tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER

  • An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier),
  • A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations.

CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass. CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions. COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electromechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted.

Glossary

COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNC, and the video.

CREDIT One play for one person based on the game switch settings. cRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. DC Direct current, meaning current flowing in one direction and of a fixed value.

DEFLECTION YOKE Electromagnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory.

Page 62

DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK . A step-up transformer used in a display to provide the high voltage. GATE

  • A circuit with one output that responds only when a certain combination of pulses is present at the inputs.
  • A circuit in which one signal switches another signal on and off.
  • To control the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used,

IMPLODE To burst inward; the inward collapse of a vacuum tube, vo input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin retum box when there is no power to the game. LOGIC STATE The binary (1 or 0) value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logie 1, High = +2.4 VDC to +5 VDC MULTIPLEXER A dgyice that takes several low-speed inpUls and combines them into one high-speed data stream for simultaneous transmission on a single line. NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request.

PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER

  • A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
  • An instrument for measuring a voltage by balancing it against a known. voltage. RAM Random-access memory. A device for the temporary storage of data.

RASTER-SCAN DISPLAY A display system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the ihtensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathode-ray tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) convert lengthy bit streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube.

WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY ‘A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.

Page 63

feel fell pel el fel fel feted pele pele pel fel pele feted peeled feted pelfelelfelred [ca]

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displ: and video-dise players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
  • Such products are returned prepaid to Seller's plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse. neglect. alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages. Excepl for any express warraity set forth in a written contract between Seller and Buyer which coutract supersedes the terns berein, this warranty is expressed in liew of all otber warranties expressed or implied. including the implied warranties of mercbantability and fitness Jor a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor autborizes any otber person to assume for the Seller any other liabilities in connection with the sale of products by Seller. Pree eee eee ele elele ele elrelel elated ele elated ele pele federal feted

lela pled pel el pel pel ed pel ped pele pele pel el pele pel fel pelea el fel el felelfelrel fel [ca)

The use of any non-Atii parts may void your warranty, according to the terms of the Warranty. The use of ny non-Atui parts may also adversely affect the safety of your oth Be very cautious in using non-Atiri-supplied arder to en your safety game and cause injury (0 you components with our games. Atari distributors are indep tely owned and operated. In their judgan Atari parts or accessories. Atari Games © quality, suitability. or safety of any: non-Atari labor which is performed by such distributor ment they may’ sell parts or accessories other Corporation cannot be responsible for part or any modification includi

Page 64

Atari Games Corporation

675 Sycamore Drive

P.O. Box 361110

Milpitas, CA 95036