CATHODE RAY TOMES

Centipede Cocktail TM-188 1st Printing

Centipede (revision 4) (Atari, 1980) · Technical Manual · 64 pages · 51 sections · original scan

Page 1

\) en)

pS) Operation, Maintenance

  • —< es Wf and Service Manual ‘S WSS SN 4 Ls LL oN WES == Gee TM
Page 2

GAME SERIAL NUMBER LOCATION Your game’s serial number is stamped on a silver identification label, located on the outside of the game. The same number is also stamped on the chassis of the monitor, Regulator/Audio || PCB, the power supply, and Centipede™ Game PCB. Please mention this number whenever calling your distributor for service.

MONITOR

CENTIPEDE™, GAME PCB

GAME SERIAL NUMBER IDENTIFICATION TAG

REGULATORIAUDIO II PCB

POWER SUPPLY

Page 3

™

oIN LA Q

Cockt. =

il

peration, Maintenance 4 and Service Manual

Complete with Illustrated Parts Lists

Page 4

Centipede™/Cosktail

Copyright © 1981 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.

Published by: ATARI INC. 1265 Borregas Avenue PO. Box 427 Sunnyvale, California 94086

Lithographed in the U.S.A. 7K

Page 5

Notice Regarding Non-Atari Parts

WARNING

Use of non-Atari parts or modifications of your Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

Atari, Inc.'s warranty (printed on the inside back cover of this manual) may be voided, if you do any of the following:

1.) you substitute non-Atari parts in your coin-operated game, or

2.) you modify or alter any circuits in your Atari game by using kits or parts not supplied by Atari.

Not only may the use of any non-Atari parts void your warranty, but any such alteration may also adversely affect the safety of your game, and may cause injury to you and your players.

Page 6

Table of Contents

Set-Up Procedures A. New Features. ... 0.0.66. ccc cece cee tent ee eens 1 B. Opening the Game Cabinet 3

  • Opening the Table Top . 3
  • Access Panel......... 3
  • Closing the Table Top 3 C. Gamelnspection ..... 3 D. Game Installation... 4
  • Voltage Plug Selection ... 4
  • Interlock and Power On/Off Switches 4 £. Adjusting the Table Legs....... 6 F. Self-Test Procedure ... . . 7 G. Option Switch Settings . - 10
  • Bonus Play Feature. ... - 10
  • Coin Mechanism Multipliers . . 10
  • Examples of Game Price Settings . - 10 H. Game Play 14
  • Attract Mode .... 15
  • Ready-to-Play Mode . 16
  • Play Mode .. . . wee 16
  • High Score Initial Mode ......... 0... cee cece eee 17

Maintenance and Repair A, Cleaning... 2... ccc cnet eee tenet teen ene 20 B. Fuse Replacement - 20 C. TheControl Panel ........ - 20

  • LED Start-Switch Replacement . .21 2, Leaf Switch Replacement........ 21
  • Mini-Trak Ball™ Maintenance and Repair . . 22 D. Monitor Removal ........ “oer . 24 —. Printed-Circuit Board Removal . os)
  • Game PCB Removal ........ . 25
  • Regulator/Audio !l PCB Removal . 25 F. Speaker Replacement ......... - 26 G. Game Operation...... 0... tenes 27

Illustrated Parts Lists Illustrations and parts lists begin on page .............. 6. eee ee ee 31

Page 7

List of Illustrations

Figure 1 Overview of Game Figure 2 Installation Requirements . Figure 3 Voltage Plug Selection ...... Figure 4 Interlock and Power On/Off Switches

Figure 5 Adjusting the Table Legs . . . 6 Figure 6 Location of Self-Test Switch, Volume Control and Option Switches ... 7 .. 8 Figure 7 Self-Test Procedure Figure 8 Game OptionSettings ..................

Figure9 Game Price Settings Figure 10 Coin Counter Option Settings ..... Figure 11 Opening the Control Panel and Replacing Switches . Figure 12 Control Panel Wiring

Figure 13 Mini-Trak Bail™ Maintenance and Repair. . . . Figure 14. Monitor Removal ..............- Figure 15 — Printed-Circuit Board Removai Figure 16 Speaker Replacement

Figure 17 Power Distribution . . Figure 18 Signal Distribution .......... :

Ilustrated Parts Lists: Figure 19 Cabinet-Mounted Assemblies ..........0 0.0.2.0 e cece eee eee ee Figure 20 Control Panel Assembly... : Figure 21 Mini-Trak Ball Assembly ..... . we Figure 22 Centipede™ Game PCB Assembly ............-0.00e0ceeeee eee

Figure 23 Regulator/Audio li PCB Assembly .....-.....0 0.2 cece cee eee eee Figure 24 Power Supply Assembly for Color Raster-Scan Games . Figure 25 Double Coin Acceptor/Mount Assembly

Page 8
NOTE If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help® at the Atari Customer Service office in your geographical area, as shown below.

WEST and CENTRAL U.S.A. Parts for all Atari customers in the U.S.A. Game sales and service

Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time) s From California, Alaska or Hawaii (408) 745-2900 From anywhere else in this area @ ‘toll-free (800) 538-1611

EAST U.S.A. Game sales and service only

Atari, Inc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) ame From New Jersey (201) 469-5993 ae» From anywhere else in this area © toll-free (800) 526-3849

EUROPE Parts for all Atari customers in Western Europe. Game sales and service

Atari Ireland Limited European Customer Service Office TIPPERARY TOWN, Tipperary Town, Ireland !RELAND Telex 28165 (Monday-Friday, 9:00-6:00 pr GMT)

@ 0062-52155

vi

Page 9

Set-Up Procedures

A. New Features

@ New-Style Cocktail-Table Cabinet. This cabinet design eliminates the side door and provides a The Centipede™ game has four new features. new location for the game printed-circuit boards Even if you are familiar with Atari games, you should (PCBs). The table top is end-hinged for easy ac-

note these important differences. The new features cess to the PCBs and control panels. The coin oe box is accessible only from the outside of the ®@ = Mini-Trak Ball™. The widely used Trak Bal! as- cabinet. sembly has been redesigned. The basis for this @ The newly-designed adjustable table legs procompact, simplified design is a two-part molded plastic frame. Fewer parts in this control make servicing easier, and its very smooth action is designed for greater player accuracy. The circuitry has non-volatile memory for part of the high score table. This means that even if power is removed from the game, the three highest scores will permanently stay in memory. To erase these scores follow the instructions in Figure 7, Self-Test Procedure.

OS vide improved cabinet stability while allowing two cocktail-table height settings: 277, and 30 inches, A third “upright” setting is 3934 inches high, and allows the game to be placed in locations with other upright games.

These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is

mentioned, you will see this symbol: ASS

Page 10

TABLE TOP

SUPPORT ARM ASS

CENTIPEDE™ GAME PCB SECURITY BAR

UTILITY COIN SWITCH, CANEL 3 SELF-TEST SWITCH, & VOLUME CONTROL

CONTROL PANEL REGULATOR! ‘AUDIO Il PCB E> <= ey POWER SUPPLY Za. ZF ADJUSTABLE LEG

POWER ONIOFF SWITCH SPEAKER

COIN ACCEPTORS.

COIN COUNTER

Figure 1 Overview of Game

Page 11
WARNING: SHOCK HAZARD Connect this game only to a grounded 3-wire outlet. If you have only a 2-wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electric shock if this game is not properly grounded!

B. Opening the Game Cabinet

  • Opening the Table Top @ To open the game cabinet, unlock and open the two locks at one end of the game, located immediately below the table top (see Figure 1). © Carefully lift the table top until the support arm locks into place. Do not jam the table top at the end of its upward swing.
  • Access Panel @ To open the access panel, lift up the “U-shaped steel security bar inside the cabinet wall. @ The access panel near the bottom of the cabinet will then come out. This small panel was designed with a bar instead of the usual lock to reduce the number of keys required for this game.
  • Closing the Table Top

Q @ To close the cabinet, stand on the start-switch

side of the cabinet and grasp the table top with your right hand. @ With your left hand, press the button at the middle of the support arm and push the support arm down towards the right. @ Gently lower the table top to the closed position. @ Lock the two latches on the left end of the cabinet, located just underneath the table top.

Cc. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

NOTE Do not plug the game in yet!
  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Unlock the table top and open the access panel of the cabinet; inspect the interior of the game as follows: @ Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. Don’t force connectors together. The connectors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB and will void your warranty. @ Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
WARNING To avoid possible unpleasant electrical shock, do not touch internal parts of the Monitor with your hands or with metal objects held in your hands!

@ Note the location of the game's serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Centipede™ Game PCB, Regulator/Audio I! PCB, power supply, and monitor are all identical. A drawing of the serial-numbered components is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. @ Check all major subassemblies such as the power supply, contro! panel and monitor for secure mounting.

(®

Page 12

Centipede ™/Cocktail

D. Game Installation

Figure 2 Installation Requirements

Power 135 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 62% x 82V2 cm (242 x 3212 in.) Game Height 65 to 101 cm (25% to 39% in.)

  • Voltage Selection This power supply has four colored voltageselection plugs and operates on the line voltage of almost any country in the world.

Before plugging in your game, check your power supply. Make sure that the voltage selection plug on it is Correct for your \ocation’s line voltage. Check the wire color on the plug and see if it is correct per Figure 3.

  • Interlock and Power On/Off Switches To minimize the hazard of electrical shock while working on the inside of the game cabinet, an interlock switch has been installed under the table top (see Figure 4). This switch removes all AC line power from the game circuitry when the table top is opened.

Check for proper operation of the interlock switch by performing the following steps: @ Be sure the table top is closed. @ Plug the AC line power cord into an AC outlet. ®@ Set the power on/off switch to the “on” position. Within 30 seconds the monitor should display a picture. @ Slowly open the table top. The monitor picture should disappear when the top is lifted approximately 2¥2 cm (1 inch). © \f the results of the preceding step are satisfactory, the interlock switch is operating properly. If the monitor doesn’t go off as described, check to see if the interlock switch is broken from its mounting or stuck in the “on” position.

WARNING

Fuse cover must be in place during game operation.

voutaGe ~ SELECTION Line Voltage Range Voltage Selection Plug Color 90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-260 VAC (240) Brown

Figure 3 Voltage Plug Selection

Page 13

SAFETY INTERLOCK SWITCH fF,

ON/OFF SWITCH (Reach unde! each under game to activate switch)

Figure 4 Interlock and Power On/Off Switches

Page 14

Centipede ™/Cocktail

@ Remove or empty the coin box. Loose coins may slide out of the coin box and into the game cabinet. © Lay the table on its side. Place a support (the coin box, books or tool box) under the recessed side of the cabinet. @ Loosen the two Allen-head screws on each leg. Grasp the legs and slide them into the desired position. Then tighten the screws.

REMOVE COIN BOX. USE TWO SCREWS WHEN ATTACHING EACH TABLE LEG!

SHIPPING POSITION (25% in.)

Figure 5 Adjusting the Table Legs

E. Adjusting the @& Table Legs

This cocktail-table game is designed for four adjustable heights—65, 70, 76 or 101 cm (25%, 27%, 30 or 39% inches). To adjust the table height, refer to Figure 5.

NOTE To ensure cabinet strength, you must use two screws when attaching each table leg. Using only one screw may result in damage to the cabinet wall when you move the cabinet across the floor.
Page 15

F. Self-Test Procedure

This game will test itself and provide data to demonstrate that the game’s circuitry and controls are operating properly. The data is provided on the monitor, light-emitting-diode switches, and game speaker; no additional equipment is necessary. Centipede™/Cocktait

Part of the self-test procedure includes a display of the operator-selectable game options. Therefore, we suggest you run the self-test procedure anytime you need to change the game's options.

To run the self-test, follow the instructions outlined in Figure 7.

OPERATOR OPTION SWITCH (one of three sets)

CENTIPEDE™ GAME PCB SELF-TEST SWITCH

VOLUME CONTROL (For volume increase, turn clockwise) COIN SWITCH

Figure 6 Location of Self-Test Switch,

Volume Control and Option Switches

Page 16

Figure 7

Instruction Self-Test Procedure

Results if Test Passes (if results are not as indicated, see list of failures that follows)

  • Begin: Set self-test switch to on position (see Figure 6).
  • Trak Ball Test: Roll the Trak Bali controls in all directions.
  • Switch Test: One after another, activate and reiease all control-panel switches, the slam switch, and coin switches.*

4, Audio VO Chip Test: One after another, press and hold 2 of the control-panel switches and at least one of the coin switches.

  • Audio 1/0 Channel Test: Press 1-player start button four times.
  • Background Color Test: Press 1-player start button at least 16 times.
  • Object Color Test: Press 2-player start button at least 16 times.
  • Moving Object Test: Watch the screen, and move the Trak Ball around. Place the moving object in an open area of the screen. Press fire button several times.
  • Erasing the High Score Table (optional) The monitor displays the picture below. The game produces no sound at all. The two start-switch LEDs will stay on throughout self-test.

The centipede head moves around on the screen in directions corresponding to Trak Ball control.

As long as you activate (close) each switch, you'll hear a high beep.

Volume increases and pitch decreases with each additional switch that is activated.

You'll hear a high beep for each press of the button.

Background color changes with each press of the 1-player start button.

Objects on playfield change color.

Each press of the fire bution changes the moving object to another moving object. At certain points in the series, the object will disappear. This is not a failure indicatio

The current three highest scores are held in permanent memory, even if the game is unplugged. If you want to erase these scores, simultaneously press either fire and two start buttons. The 4 FF message in the upper left corner of the screen will then be displayed. The average game time data will also be erased, but still displayed on the screen.

  • End: When satisfied with test, set self-test switch to off position.
  • Activate coin switches by inserting at least one coin in each coin slot. You will not trip the coin counters as long as you stay in self-test.

ENTIRE CHARACTER SET NO. OF LIVES AT START OF GAME

ALL SWITCHES & TRAK-BALL INPUTS. oOo1oek URN LR COIN MECH MULTIPLIERS BONUS COIN SETTING (means “for every 3 coins inserted, logic adds 1 more coin”), Blank if no bonus coins(s) given. See Fig. 8 for switch settings. OoLoyh TOTAL NO. OF CREDITS PLAYED

AVG. GAME TIME (accurate to + 4 secs.) Ob PLAYS: 1:59 GAME TIME

GAME DIFFICULTY SETTING

Page 17

Figure 7 Self-Test Procedure, continued

Results if Test Fails

  • Begin: RAM FAILURE is indicated by one to 10 beeps. Note the number of beeps and determine which RAM may be bad. To restart the test, press the reset pushbutton on the game PCB, or set the selftest switch to oft, then again to the on position. Possible Bad Number of Beeps Given RAM Chip Location H2 F2 K7 KS

us M7 M5 N7 10 N5 Any bad RAM must be replaced before the computer can check the other RAMs, as well as continue with the self-test. ODN TRONS

ROMIPROM FAILURE is indicated by two groups of numbers in the upper left corner of the screen. The number at the far left indicates the location of the failing PROM/ROM(s). Identify the bad ROM/PROM with the table below. If the screen displays “garbage,” or the logic produces strange audio or randomly activates the coin counters, the chip at location J1 is probably bad. Ignore the hexadecimal numbers just to the right of the chiplocation number. Failing ROM/PROM. Displayed Number Chip Location oO O1 1 et 2 FIHt 3 or “garbage” Jt 4a* E5* 5 BICID3 *If you replace or erase this ROM, the number 4 FF will be displayed throughout the self-test. The next time you enter self-test, the 4 disappears after a game is played. Otherwise the self-test will continue to display the numbers 4 FF.

  • Trak Ball Test: The character doesn't move in same direction as ball, jumps rather than moves smoothly, or doesn't move at all. One of the Coupler PCBs in either Trak Ball control may be bad, harness wires or connector may be loose, Trak Ball reading circuitry on Game PCB may be bad, or Trak Ball bearings may need oiling.
  • Switch Test: Sound is constantly on, even though you are not activating any switch. Or, no beep is given for any switch, or LEO is dark. indicates a bad switch, loose harness wires, bad LED-driving circuitry, volume turned all the way down, or loose connector,
  • Audio VO Chip Test: No increase in volume or decrease in pitch indicates bad custom audio '/0 chip at location B/C/D3.
  • Audio /O Channel Test: On one out of the four activations, no audio is produced. indicates ‘one channel is bad in the custom I/O audio chip at location B/C/D3. (replace entire chip).
  • Background Color Test: Background doesn't change color, or doesn’t display all 16 colors. Indicates bad color RAM chip. (RAM failure would have been indicated earlier with from 3 through 10 beeps.)
  • Object Color Test: Objects don't change color, or don’t display all 16 colors. RAM failure.
  • Moving Object Test: Object doesn’t change to another object. ROM/RAM failure. Ss
Page 18

Centipede™ Cocktail

G. Option Switch Settings

  • Bonus Play Feature Centipede™ offers a bonus play for certain combinations of coins inserted. This bonus feature is operator-selectable, meaning you may choose to offer it or not.

With your game set at 25¢ per play, players who deposit four successive quarters or a $1.00 coin, then press the start button, can receive a bonus coin. Therefore, players can receive 5 plays for $1.00.

This bonus feature encourages players to insert more money than just the minimum 25¢ you could require for one game. Various other bonuses are also available (see Figure 9).

  • Coin Mechanism Multipliers The Atari coin acceptor mount for this game is available with about a dozen different mechanisms. You may have both mechanisms accept the same or different denominations. Regardless of the type of mechanism you install, you must correctly set the mech “multipliers” on the game PCB. The multipliers determine how much each mechanism will be worth to the game’s logic.

The basic unit of measurement is 25¢, which equals a multiplier of x1. Therefore, if you have a 25¢/$1 coin acceptors, you will probabiy want to set the left and right option-switch multipliers at xx 4,

You can set these multipliers with toggles 3 thru 5 on the Centipede PCB switch assembly at location N8. For exact settings of these toggles, refer to Figure 9.

  • Examples of Game

Price Settings

Figure 9 explains the options, giving twelve examples of the most common U.S. situations. The toggles mentioned are all in the switch at location N8; they only relate to game price, coin mechanism multipliers, and bonus “coins” for inserting multiple quarters or the $1.00 coin. You should set the toggles relating to other functions as you see fit, although Figures 8, 9, and 10 provide “$” symbols indicating Atari’s recommendations.

Page 19

Figure 8 Game Option Settings To change toggle positions on the switch assemblies, you need not remove the game PCB. The switches, usually colored blue, are easily accessible when the Centipede Game PCB is mounted in place. When changing the options, verify proper results on the monitor display by performing the self-test. Note that changing an option on any of the following eight toggles will not cause an immediate change on the monitor screen during the attract mode.

Toggle Settings of 8-Toggle Switch on Centipede Game PCB (CENTER switch assembly when PCB is in game) 8 7 6 5 4 3 2 (at N9)

1 Option

On On Off Off

On On On Off

Off On

Off Ott

On On On oft off On

Off Oft

On Off

On Off On English $

Off German

On French Off Spanish 2 lives per game 3lives pergame $ 4 lives per game 5 lives per game

Bonus life granted at every: 10,000 points 12,000 points $ 15,000 points 20,000 points Hard game difficulty* Easy game difiiculty* $ 1-credit minimum $ 2-credit minimum

$ Manufacturer's suggested settings *Refer to Section F. Game Play, in this manual for information on game difficulty. For pricing for “credits,” see Figure 9. Changing toggles 37 erases the high score table,

al)

Page 20

Figure 9 Game Price Settings The white block below contains Atari’s suggested settings. All numbers 1 thru 8 are toggle settings on the 8-toggle switch at location N8, on the Centipede™ game PCB (the LEFT switch assembly). Circled numbers refer to game pricing labels you should use with each situation (labels are on the following page). Use the label no. 6 (indicated with®) only if you set toggle 8 at PCB switch assembly N9 of off.

50¢ PER CREDIT:

No bonus Bonus Bonus $.75 = 2 plays $1.00 = 3 plays $1.00 = 3 plays =

25¢/25¢ Mechanisms

25¢/$1.00 Mechanisms

25¢ PER CREDIT:

Bonus Bonus No bonus $.50 = 3 plays $1.00 = 5 plays

8765aS
2501256@onofofof

Mechanisms

@®4324
OffOffOnOff

25¢/$1.00 Mechanisms

Page 21

Figure 9 Game Price Settings, continued To achieve bonus plays, all coins must be inserted before pressing the start button. The iabel no. 6 shown below should be used only if you set toggle 8 at PCB switch assembly N9 to off. For your information, we have defined below the switch settings for those options relating to game price, coin mechanism multipliers, and bonus play. This information is useful in case you need to temporarily set the Centipede™ game on free play. or if you have German coin mechanisms in your door.

Toggle Settings of 8-Toggle Switch on Centipede PCB (at N8—LEFT switch when PCB is in game)

87654321Option
OnOnFree play
OnOff1 coin* for 2 credits
OffOn1coin* fort credit$
OffOff2 coins* for 1 credit
OnOn.Right coinmech x 1$
OnOffRight coin mech x 4
OffOnRight coin mech x 5
OffOffRight coin mech x 6
OnLeft coin mech x 1$

Off Left coin mech x 2

OnOnOnNo bonus coins$
OnOnOff

On Off On On Off Off Off On On

OffOnOff

For every 2 coins* inserted, game iogic adds 1 more coin* For every 4 coins* inserted, game logic adds 1 more coin* For every 4 coins* inserted, game logic adds 2 more coins*

For every 5 coins* inserted, game logic adds 1 more coin* For every 3 coins* inserted, game logic adds 1 more coin*

*In the U.S., a “coin” is defined as 25%. In Germany a “coin” is 1DM. $ Manufacturer's suggested settings To achieve bonus plays, all coins must be inserted before pressing start button. Game Pricing Labels:

ATARI e A, @@ 2 coins =1 play

vd ;

ZK@1 coin=1 play

AO @ @ 2 coins = 1 piay ATARI

6 eee 4 coins = 3 plays

° ee 2 coins

nO @@ 2coins 8! @@@ 3 coins 400 @ 4 coins

1 play A @ $1 coin =3 plays (Susan B. Anthony coin)

oO, @ 1 coin = 1 play ame 2 play minimum (2 coins = 2 plays)

C7) (For operator use—write in

AR the appropriate phrase. Use

@ permanent is ATARI tat marker)

Page 22

Figure 10 Coin Counter Option Settings

[These toggles determine which coin mechanisms activate which counters]

Toggle Settings of 4Toggle Two coin acceptors and a push- Switch on Game PCB (N11) Two coin acceptors button utility coin switch in the Three coin acceptors

4324in the coin door:game:in the coin door:
OnOnBoth acceptors activate all coinDo not use this setting.All 3 are same denomination and

counters simultaneously. they activate all coin counters simultaneously.

OnOffBoth acceptors activate 2 count-Do not use this setting.Left and center acceptor activate

ers separately. ‘one coin counter; right acceptor ac-

38tivates another coin counter.
3>OffOnBoth acceptors activate all coinUtility coin switch will not acti:Left acceptor activates one coin
$$3counters simultaneously,vate a coin counter, if you do notcounter; center and right acceptor

hook it up. Both acceptors acti- activate another coin counter. Not vate all coin counters simultane- for any currently designed 3-mech ously. coin door,

OffOffBoth acceptors activate 2 count-Utility coin switch will not ac-Left, center and right acceptors acti-

ers separately. tivate a coin counter, if you do vate 3 coin counters separately. not hook it up. Left and right acceptors activate 2 coin counters separately. $

, 8 Manufacturer's suggested settings

H. Game Play

Atari’s Centipede™ is a one- or two-player game with acolor raster-scan monitor. The fast-moving action includes a variety of creatures dropping down from the top of the screen or flying in from its sides, most of them to attack the player. The player's shooter is represented on the screen by a somewhat humanoid head.

The player's goal is to shoot at and destroy as many of these creatures and mushrooms as possible for a high point score, before the player's lives are used up. Players can maneuver their Trak Ball™ control anywhere within approximately the bottom fifth of the screen. However, they must move around mushrooms, since these are fixed, not “transparent”, objects. A fire button shoots individual shots upwards, or fires a hail of shots if pressed constantly. (Only one shot appears on the screen at a time.)

The game has five possible modes of operation: attract, ready-to-play, play, high score initial, and self-test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled. Wait at least eight seconds after a game has been played before entering se/f-test or turning off the power. Otherwise, you may erase the high score table. “

Page 23
  • Attract Mode The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a game is paid for and accepted or when in self-test. In this mode, the monitor displays two pictures simultaneously.

One of the pictures is operator-selectable for one of four languages. Placed in the center of the screen, the picture shows the high score table, game price, and the bonus-life achievement level. If the operator sets the Centipede game for free play, the game will not display a game price message.

The high score table shows the eight highest scores and their matching initials. If you erase the special “permanent” memory (see Figure 6, Self- Test Procedure), then this table will contain fictitious scores and initials. The table is redeveloped from subsequent games with scores of more than 12,102 points. Subsection 4, High Score Initial Mode, explains this table in more detail.

Operators may choose one- or two-credit maximums by selecting one of the option switch settings on the game PCB (see Figure 7, Game Option Settings).

If the game is set for a 2-credit minimum, that message will be displayed on the screen. (No special message appears if Centipede is set to the opposite setting, namely 1-credit minimum.) The other picture surrounds the high score table, game price and bonus-life achievement level messages. That picture displays a typical game-play sequence, with a field of colorful mushtooms through which a centipede crawls. The spiders bounce in from the sides of the screen, and fieas occasionally drop down from the top. In addition, scorpions will cross the screen at almost any point.

In this mode, the action exactly duplicates a typical game played by a moderately skilled player: the player’s shooter moves freely within the limits of motion, shooting at spiders, centipedes, fleas and scorpions. Periodically the player is “destroyed” when a flea, spider or centipede head or body coilides with the player's shooter.

All the colors on the screen change with each wave. A new wave occurs when the player shoots all centipede parts remaining on the screen. At this point, a new centipede starts snaking its way down from the top of the screen.

The attract mode differs from real game play in that no head figures are shown at the top of the screen to represent the number of lives remaining, no sounds are produced, no scores are incremented, and none of the player controls work.

At any time when the game is powered up, if the slam switch is closed, you will hear a special alarm sound. This sound alerts location personnel that the game has been abused.

NZ

“"\

Page 24
  • Ready-to-Play Mode This mode begins when sufficient coins are accepted for a one- or two-player game. It ends when the 1-player start or 2-player start pushbutton is pressed. When this mode begins, the message CRE- DITS __ is displayed in the middle of the screen. The pictures are otherwise the same as those shown in the attract mode.

\f you select the two-credit minimum and a player inserts enough money for only one credit, the message 2 CREDITS MINIMUM flashes on the screen until snougly coins for the second credit are inserted.

In addition, CREDITS 0% is displayed if you have selected the option of two coins per credit, and the player has inserted only one coin. A “credit” is defined as the cost for each player to play one game. In other words, two credits will pay for:

© one player playing two games, or @ two players playing one game.

  • Play Mode The play mode begins when any flashing start pushbutton is pressed. The mode ends when the player’s last life is lost.

If a two-player game is being played on a cocktailtable game, the screen image will invert 180 degrees with each new life. This places the shooter immediately in front of the players.

A player's shooter is enabled at the beginning of the play mode, and the audio starts. The appropriate LED start switch will then stay lighted until the end of the game. At this point it will flash if any credit remains. The game begins with a playfield of randomly placed mushrooms. A centipede start snaking its way across from the center top of the screen. The centipede changes direction when it runs into a mushroom or either the left or right boundaries of the playfield.

When a centipede is shot, it breaks into two smaller ones, each with a head. Also the part of the centipede that was shot leaves a mushroom in its place on the screen. When any centipedes reach the bottom of the screen, they start back up, but remain within the area of the player's shooter (the bottom fifth of the screen).

When a large centipede (that hasn't been shot yet) reaches the bottom, it releases its tail, and this part changes into a new head. Also to provide player challenge, if a centipede is still alive when it reaches the bottom, new heads will enter the screen almost at the bottom of the sides. More of these heads will appear as time progresses.

The randomly moving spiders also appear in the first wave. The spiders can destroy a player, as well as any mushrooms they move over. This eliminates many mushroom targets for a player.

The player’s shooter is moved by rotating the Mini-Trak Ball™ control. The shooter can be moved in all directions, but only within the bottom fifth of the screen. Pressing the fire button causes the shooter to fire shots upwards, either singly or in rapid-fire mode, if held down constantly.

Mushrooms count 1 point when shot, and a player must fire four shots into a mushroom before it is destroyed and disappears. Centipede body parts count 10 points each, and the elusive heads (represented with small eyes on them) are worth 100 points each. Spiders are worth 300, 600 or 900 points, depending on how close they are to the player when shot.

Page 25

A bombardment of fleas starts in the second In the hard setting, the spider moves slowly only wave; as the fleas descend, they leave a trail of new for the first 1,000 points, and then speeds up. It also mushrooms behind them. changes direction more often throughout the game. In either setting, the spider always moves at a In the second wave, the fleas appear when a cer- 45-degree angle or straight up and down. tain number of mushrooms remains at the bottom of co. . the screen. This number increases as the game pro- Another operator option is the number of lives per gtesses, meaning fleas appear more often later on in game, ranging from 2 to 5 (see Figure 7 for switch the game. settings). This number is displayed as smal! shooters at the top of the screen. The number is de- Fleas have a value of 200 points when shot, and creased by one each time a player is destroyed. The players must hit them twice to destroy them (the | number is increased by one each time the player first shot just speeds them up). scores multiples of 10, 12, 15 or 20 thousand points, depending on the operator selection. The scorpion enters from either side starting in . tae the fourth wave; it moves at a relatively slow speed. 4. High Score Initial Mode Later it increases its speed. When shot, a scorpion If a player’s score exceeds the minimum on the counts 1000 points—the highest-value target of all. high sore initial list, he or she may put up to three F neh ” initials on this list at the end of the game. At the be- As it travels across the screen, it “poisons” the ginning of this mode, the characters A ___ appear mushrooms that it moves over and changes their on the screen. The logic will aiso display the mescolors. These mushrooms cause any centipedes that would collide with them to head straight to- sages GREAT SCORE and ENTER YOUR INITIALS. wards the bottom of the screen, rather than con- Players enter initials one character at a time, tinue snaking around. Players can stop a poisoned choosing from the characters A thru Z and a blank centipede by shooting its head. space. Pressing the first button selects the letter, and rolling the Mini-Trak Ball™ contro! changes the In addition, these poisoned mushrooms as well letters on the screen. as any partially shot mushrooms add 5 points to the player's score at the end of each life when the screen is resetting. After the fire button is pressed the third time, the initials and score are transferred to the table. This table contains eight scores and appears during the If the players are very skilled and earn at least —ttract and ready-to-play mode. 60,000 points, two things happen to increase player All but the hi . ighest three scores are erased whenchavienge: the lade descend at a faster nace and ever you enter the self-test, or press the RESET bute spiders restrict their movement to a smaller area ton on the game PCB, or turn off the power. The rea" the bottom of the screen. setting replaces the lowest five scores with ficti- An important new feature of this game is the oper- tious’scores and initials. 7X) ator option for easy/hard game difficulty. In the easy If you erase the special “permanent” memory, the game, the spider moves slowly up to a 5,000-point high score table is replaced with eight fictitious score, and then bounces at a higher speed. It also scores and initials. In other words, the table will alchanges direction less often throughout the game ways be displayed on the screen, possibly consisting than at the hard setting. of one or more realistic scores and players’ initials.

Page 26

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 27

Maintenance and Kepair

All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the

coin box. Just looking at a game will not tell you if ASS

Mini-Trak Ball™ controls, light-emitting-diode switches or leaf switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly clean the leaf switch contacts and lubricate the Trak Ball control: for details see this chapter.

Page 28

LEAF SWITCH

TURN NUT TO RE- MOVE WHITE BUTTON

Figure 11

A. Cleaning

The exterior of the game cabinet and the metal, glass, and plastic surfaces may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor.

The large table top is made of tempered glass and should be scratch-resistant. lf cleaned without abrasive substances, you should hardly ever have to replace them.

B. Fuse Keplacement

This game contains six fuses—all on the power supply assembly (not including the monitor fuses). Replace fuses only with the same type as listed in Figure 24 of this manual. See the Matsushita monitor manual, TM-153, for the monitor fuse data. COMMON CONTACT \

2 NORMALLY OPEN NS {N.O.) CONTACT LIGHT-EMITTING-DIODE (L-E.D.) CONTACTS.

NORMALLY CLOSED (N.C.) CONTACT

To Remove LED Switch: Remove all wires from the faulty switch. ®@ Turn the switch counterclockwise while holding the black cone-shaped bushing on the outside of the control panel. @ Install a new switch using the reverse procedure. @ Reconnect the harness wires.

CAUTION Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.

Opening the Control Panel and Replacing Switches

C. The Control

Panel

Prior to repairing or replacing any switch or the Mini-Trak Ball™ on the control panel, unplug the game. Next, open the game top as described in Chapter 1, Section B, Opening the Game Cabinet.

Finally, remove the two sets of button-head screws and lock washers at the top edge of the control panel. Once this hardware is removed, the control panel will tilt toward you.

After servicing the start switches or any components on the control panels, be sure you reconnect the harness wires to the proper termination points, as shown in Figure 12. Otherwise the controls may not work properly—causing frustration in players and possibly reduced income from the game. AS

Page 29
  • LED Start-Switch Replacement The light-emitting diode (LED) switches near the control panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 11.

@ Remove the wires from the suspected switch. @ Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter. ® Connect multimeter leads to appropriate LED switch contacts (see Figure 11 for designation of switch contacts and meter lead placement). @ Check contacts (push and release the switch button) for closed and open continuity. @ If the contacts do not operate sharply or always temain closed or open, then replace the LED switch as ouilined in the figure.

  • Leaf Switch Replacement
NOTE Adjust switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the contacts provides a self-cleaning feature.

All five of these leaf switches operate on 5 volts at a very low current. Therefore, pitting of these switches would be extremely rare. Probably the only reason that pitting would occur is that the game is in a very high-humidity location.

Don’t burnish the switches. Burnishing them removes their plating, thus increasing the corrosion of the contacts. The best method of cleaning the switch contacts is to wipe them with a non-abrasive surface. A business card works very well.

CAUTION Players may receive an electric shock if this control panel is not properly grounded! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the inside of the contro! panel. Only then should you lock up the game. BLACK

RED

GREY STRIPE

WHT. WITH BROWN STRIPE VERT.-MOTION PCB: GREEN RED, BLACK & YELLOW WIRES

HORIZ.-MOTION PCB: BLUE, RED, BLACK & VIOLET WIRES. WHT. WITH ———— +

WHT. wit BLACK STRIPE BLACK

2 WIRES MAY BE HOOKED UP EITHER WAY 2-PLAYER START SWITCH

1-PLAYER START SWITCH

+

WHT. WITH RED STRIPE

Figure 12 Control Panel Wiring

Page 30

To replace any switch, remove both of its screws with a Phillips-head screwdriver—see Figure 11.

\f the white button itself needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The white ring on the outside of the contro! panel should not spin, due io its design.

  • Mini-Trak Ball™ Maintenance

ah and Repair

The Mini-Trak Ball™ control requires lubrication of its bearings approximately every 6,000 credits or every 3 months. To lubricate or repair the control, remove the control from the control panel and disassemble it as illustrated in Figure 11.

Use only 2 drops of 3-in-One® oil in each of six ball bearings of the Mini-Trak Bal! control.

For further instructions on how to replace the ball, either coupler PCB or either encoding wheel, see Figure 11.

Page 31

Centipede™/ Cocktail

Disassemble in the order indicated. (Circled numbers match the steps described below.)

Ball Replacement

  • First remove the entire Mini-Trak Ball assembly from the control panel as shown in Figure 11. Now locate the six “twin-lead” thread-forming screws in the black frames (plastic pieces); remove these six screws.
  • Lift off the top frame; remove and replace the ball.

Coupler PCB and Encoding Wheel Replacement

  • Lift the PCB out of its slot. Carefully unplug the red connector on the coupler PCB. 4, To replace eitehr encoding wheel, remove the PCB from its slot. Remove the socket-head machine ‘screw, flat washer, and split lock washer that secure the encoding wheel. Remove the wheel. ; When replacing the coupler PCB, be certain that the black metal encoding wheel has not been bent or damaged. It should turn freely between the two halves of the red photosensor device.

LUBRICATE HERE (6 PLACES)

Figure 13 Mini-Trak Ball™ Maintenance and Repair

Page 32

Centipede™/Cocktait

D. Monitor

Removal

WARNING Shock Hazard High voltages may exist in any television or monitor, even with power disconnecied. Use extreme caution and do not touch electrical paris of the yoke area with your hands or with metal objects in your hands! Implosion Hazard If you drop the monitor and the picture tube breaks, it will implode! Shattered glass and the yoke can fly 6 feet or more from the implosion. Use care when replacing any monitor. If you should need to remove the color monitor, follow steps 1 thru 5 as listed on this page. Refer also to Figure 14.
  • Be sure the game is unplugged from its wall outlet! Unlock and open the table top.
  • Lift up the “U"-shaped security bar, located along the inside wall of the cabinet. Remove the bar entirely from the cabinet. Remove the access panel from the side of the game.
  • Locate the 6-pin monitor and 3-pin power connectors underneath the monitor, just above the power-supply transformer. Unplug these connectors.
  • Remove the four Phillips-head screws and flat washers (one set at each corner of the monitor screen). These attach the large monitor brackets to the cabinet.
  • Carefully lift the monitor assembly up and out the cabinet.

Disassemble in the order indicated. (Circled numbers match the steps above.)

Figure 14 Monitor Removal

Page 33

2s

CAUTION Be sure to let the game cool down (with power turned off and the table top open) for at least 10 minutes. The large black heat sink on the Regulator/Audio Il PCB gets fairly hot. You could burn yourself on this heat sink while removing the PCB.

CENTIPEDE™ GAME PCB

REGULATOR! AUDIO It PCB

Figure 15 Printed-Circuit Board Removal

E. Printed-Circuit Board Kemoval

You may wish to remove the game printed-circuit board (PCB) or the Regulator/Audio || PCB for service or inspection. To do this, refer to Figure 15 and Proceed as follows:

  • Game PCB Removal @ Unlock and open the table top. @ Remove the four beaded nylon tie-wraps from the top side of the game PCB. Then remove the two edge connectors. @ Locate the Phillips-head screws that extend through the PCB and into the two wood blocks near the top of the game. Remove and save these Screws and the associated fiber washers. @ Remove the PCB from the game by carefully sliding it straight up out of the plastic PCB retainers. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. @ After servicing it, reinstall the PCB, making sure that the edge connectors are properly plugged in. Note that the connectors are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your game and will void the warranty. @ Check that the operation of the game is correct by performing the self-test. This is especially important with any game when you replace a PCB.
  • Regulator/Audio || PCB Removal @ Unlock and open the table top. @ Remove the five plug-in connectors on the Regulator/Audio PCB. Note that all of these connectors are keyed for proper orientation. @ Remove the PCB from the inside wall of the cabinet by pulling it up and out of the wood retainers.
Page 34

PLUG-IN CONNECTORS

SPEAKER

Figure 16 Speaker Replacement

F. Speaker

Replacement

CAUTION Be sure to let the game cool down (with power turned off and the table top open) for at least 10 minutes. The large black heat sink on the Regulator/Audio | PCB gets fairly hot, and you could burn yourself on this heat sink while removing the PCB. If the loudspeaker should ever need to be replaced, follow these instructions and refer to Figure
  • Probably the only cause of speaker failure is an open voice coil or a ruptured cone, but both of these failures are highly unlikely.

Open the table top. Unplug both speaker-wire connectors. Use a very short-handled Phillips screwdriver to remove the two screws. For greater ease in reaching these screws, and to prevent slipping and damaging the Regulator/Audio || PCB, remove this PCB first.

Page 35

G. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for the Centipede™/Cocktail game. Sheet 1, Side A, includes a "table of contenis” that shows the arrangement of these diagrams. They explain the functions of the circuits; the diagrams also define inputs and outputs. BR Atari's Centipede™ is a microprocessor-controlled game. The microprocessor is mounted on the game PCB. The game PCB receives switch inputs from the control panels and coin acceptors. These inputs are processed by the game PCB and output to the monitor, Regulator/Audio II PCB, loudspeaker and control panel. The Regulator/Audio || PCB performs two functions: 1) it regulates the +10 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VDC from the Regulator/Audio Il PCB provides most logic power to the game PCB. The audio output from the Regulator/- Audio II PCB directly drives the game speaker and is controlled by the volume control, mounted on a bracket inside the game cabinet.

The power supply is the source of all voltages in the game. These voltages are protected by three fuses (F3, F4 and F5) on the power supply chassis. The primary winding of the power-supply transformer is protected by the fuses F1 and F2 on the power-supply chassis.

Figure 17 illustrates the distribution of power in this game. Figure 18 illustrates the distribution of signals.

Page 36

COLOR MONITOR

GAME PCB INTERLOCK SWITCHES

COIN ACCEPTORS

AC POWER CORD

POWER ON/OFF SWITCH

POWER SUPPLY

Figure 17 Power Distribution

Page 37

COLOR MONITOR

GAME PCB

VOLUME CONTROL, SELF-TEST SWITCH & UTILITY COIN SWITCH

CONTROL PANEL (1 of 2)

Q| $ =

SPEAKER

REGULATORIAUDIO II PCB

COIN ACCEPTORS

Figure 18 Signal Distribution

Page 38

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 39

Illustrated

Parts Lists

This chapter provides you with the necessary information for ordering replacement parts for your Centipede™/Cocktail game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists are arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00- thru 99-, then 000598- thru approximately 190000-.

When ordering parts from your distributor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Page 40

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, oF license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for 035852-01 Taruiacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right is granted 82-406 {Comer Bt) ep riien eprecenectcati cr omier aes a 037755-01 (Eyebolt) the corporation Se Perens 1 (Glass Table Top) 037759.01 _— (Wood Table Top) ae a9 A & 034536-03 681. i en Seay (Vibra. Damper)

{A 035851.01 | (Hinge) 178015-001 (Tabletop Support) 037686-01 7430008 (Cab. Grille) 177001-130 (Metric Hex Nut) ‘A037756-01 A036153-01 (Mon. Assy.) (Monitor only) (Tubular Spacer)

A036189-01 037685-01 (interl. Sw. w/Brkt.) (Mon, Mntg. Plate) 007882-02 (inter. Sw. Cvr.)

71-2110 037693-01 (Lock) (Secur. Bar)

036774.01 (End-Pni, Grille)

035848-01 (Leg Backplate) -.) ‘A037680-01 (Cab. Base Assy.)

403729201 (Leg Supp.)

037683-01 eas (Access Panel) A037246-01 J (Endcap) (Leg Assy.) } 78-3206 03677301 ) Grille) K Tf, (Leg)

02-305010 sheen " (Cab. T-Molding)

Figure 19 Cabinet-Mounted Assemblies A037760-xx B

Page 41

Schematics, Self-Test Label & Manuais— ‘see parts list on following page

(Toltop. T-Moiding) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproductien forbidden without the spe: cific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor Possession thereof confers or transfers any right in, of ti Cense to use, the subject matter oi the drawing or any de- ‘sign or technical information shown thereon, nor any right to reproduce this diawing or any pan thereof. Except for manulacture by vendors of Atari, Inc., and for manutacture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereat, un- 71-3201 less by writen agreement with or writen permission from 095745-02 wer for Locks) the corporation, (PCB Retainer)“ Qgg764.01

Centipede Game PCB— (Hook-Type Cam) 78-6900401 (Foam Tape) see Figure 22

A037698-01 (Main Harns.) 035867-02 (Mon. Overlay) 78-24012 (Tie Wrap)

RegJAudio Il PCB— 75-07017 (PGR Spacen see Figure 23

036321-01 (Bracket) 69-001 (Self-Test Sw.) 19-9032 com Vinheta (Vol. Ctrl.) 62.041 (Util. Coin Sw.) Mini-Trak Ball/™™— 75-9910NO see Figure 21 (Stamped Nut) 037768-01 (Fan Grille) 48-00. Canopies) Goeaxer) (Fan—op' 000869-01

ZZ (Spkr. Grille)

A034841-08, = A034863.08 or Ve A035989-08 \ (Power Cord)

Power Supply— 75-9910WO see Figure 24 (Stamped Nut)

62-039 61-1624 (LED Sw.) noron ) 033127-01 r (Sw Bushing) aaa el 037682-01 (OniOft Sw. Cvr.)

A036775-01 (Coin Box) (Mntg. Plate)

037753-01 (Retng. Bracket)

Coin Accep./Mt. Assy.— see Figure 25

Figure 19 Cabinet-Mounted Assemblies A037760-xx B

Page 42

Centipede ™/Cocktail

Figure 19 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description A002465-01 Coin Counter A005133-01 Cooling Fan (optional equipment)

A034841-08Strain-Relief Power Cord(U.S.)
A034863-08Strain-Reliel Power Cord(Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece,

Indonesia, italy, Netherlands, Norway, Spain. Sweden, and Uruguay)

A035989-08Strain-Relief Power Cord(Australia and New Zealand)

A036153-01 14-Inch Matsushita Monitor only

A036189-01(Interlock Switch with Bracket(modified for safety)

A036775-01 Coin Box Assembly (includes lock) A037246-01 Leg Assembly (includes jeg, 2 adjustable feet and 2 endcaps)

A037292-01Leg Support Assembly(includes 2 pane/ nuts and endcap)AS
A037680-01Cabinet Base Assembly(includes grilles, PCB retainers, leg backplate and hinges)

A037698-01 Main Harness Assembly A037756-01 14-Inch Matsushita Monitor Assembly (includes mounting plates and hardware) The following five items are the technica! information supplements to this game:

DP-188-01Centipede™/Cocktail Schematic Drawings(Sheet 1)
DP-188-02Centipede/Cocktail Schematic Drawings(Sheet 2)

ST-188 Centipede/Cocktail Label with Self-Test Procedure and Option Switch Settings TM-153 Service Manual for 14-Inch Matsushita Color Monitor TM-188 Centipede/Cocktail Operation, Maintenance and Service Manual

02-305006"¥.-Inch Black Plastic T-Molding(for table top)

02-305010 3%4-Inch Black Plastic T-Molding (for cabinet base)

19-903250-Ohm, 12¥2-Watt Wire-Wound Rheostat(for volume control)

48-004 5-Inch, 8-Ohm, 5-Watt, Round High-Fidelity Speaker 61-162A DPST Power On/Off Toggle Switch 62-039 Momentary-Contact SPDT Light-Emitting-Diode Switch with Red Cap 62-041 SPDT Momentary-Contact Pushbutton Utility Coin Switch with Black Cap 69-001 DPDT Self-Test Switch

71-2110Pane! Cartridge Lock Mechanism(for table top)

71-3201 Anchor Washer for Table Top Locks 74-3003A #10 x %,Inch-Long Aluminum Tubular Spacer (for table top support) 75-07017 Spacer for Mounting Printed Circuit Boards 75-9910NO #5,-11 Steel Stamped Nut (for utility coin switch) 75-9910W0 #'%,.-32 Steel Stamped Nut (for start switches)

78-240125-Inch Beaded Nylon Tie Wrap(for game PCB edge connectors)

78-3205 Square Black Endcap for Leg Assembly 78-3206 Cabinet-Leveling Leg 78-6900401 Vinyl Foam Single-Coated-Adhesive Tape, 14-Inch Wide x %,-Inch Thick (10% feet req’d.) 82-406 #14-20 x 2-Inch-Long Eyebolt, with %-Inch Threads 000869-01 Speaker Grille 006450-01 On/Off Switch Mounting Plate 007882-02 Interlock Switch Cover 009992-01 On/Off Switch Cover 033127-01 Black Molded Switch Bushing 034536-03 Foam Vibration Damper 035745-02 18-Inch-Long Plastic PCB Retainer 035848-01 Backplate for Attaching Leg 035851-01 Tabie Top Hinge [Continued on next page}

Page 43

Figure 19 Cabinet-Mounted Assemblies, continued Parts List

Part No. Description 03585201 Corner Bracket for Table Top 035867-02 Smoke-Color Acrylic Monitor Overlay 036321-01 Bracket for Volume Control, Self-Test and Utility Coin Switches 036764-01 Hook-Type Cam for Lock 036773-01 Grille in Cabinet Base 036774-01 Upper End-Pane! Grille 037335-01 Leg Brace 037681-01 Cardboard Monitor Bezel 037682-01 Mounting Plate for Start Switches 037683-01 Access Panel 037685-01 Monitor Mounting Plate 037686-01 Slip-n Cabinet Grille (above control panel) 037693-01 “U"-Shaped Security Bar 037753-01 Coin Acceptor Retaining Bracket 037755-01 Tempered-Glass Table Top with Graphics 037759-01 Wood Table Top only 037768-01 Fan Grille (fan is optional—see part no. A005133-01) 177001-130. Metric M5-0.8 Zinc-Plated Steel Hex Nut (for monitor mounting plate) 178015-001 Hinged Table Top Support

Page 44

Centipede™/Cocktatl

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the spetic written permission of AtarlInc., Sunnyvale, GA. Ths Gtawing !s only Conditionally issued, and neither receipt nor . Banga teal corer a vats any gh ic NOTE: Graphics decal is Bense to use, the subject mattor of the drawing ot any design of technical information shown thereon, r2r any “ight not field-replaceable. tofepruce tie drawing or any pot ined. Enea for Tarutaclore by vendors of Atary nc, and for manufacture . under ine corporalion's wnten lieense, ‘no right is granted Mini-Trak Ball™ Assy.— Torenreduce this drawing or the subjeci matter thereot, Unlees by wntten agreement with or writen permission fram See Figure 21 the corporation,

178030-001 (Pushbtn. Assy.)

A037763-01 (Ctrl, Pal.)

75:9910NO (Stamped Nut)

03767601 160013.001 (Harness) (Leai Sw. Button Holder) 160012-001 (Leaf Sw, Only)

CAUTION Players may receive an electric shock if this control pane! is not properly grounded! After servicing any parts on the panel, check that the ground wire is firmly attached to the metal tab on the inside of the control panel. Only then should you lock up the game.

Figure 20 Control Panel Assembly A037764-01 A

Parts List

Part No. Description

A037676-01 Control-Panel Harness A037763-01 Control Panel with Graphics 75-9810NO #5,-11 Steel Stamped Nut 160013-001 Leaf Switch and Button Holder (leaf switch only is part no. 160012-001) 178030-001 Pushbutton Assembly

Page 45

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 46

176010-106 FY (6 PLACES) 1 (Screw) NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor Possession thereot confers or transfers any right in, OF fr Cense to use, the subject matter of the drawing or any desigh or technical Information shown thereon, neg any right to reproduce this drawing or any part thereo!. Except for manufacture by vendors of Atari, Inc., and for manufacture Under the corporation's written license, no right is granted to reproduce this drawing or the subjeci matter thereo!, unless by written agreement with or written permission from the corporation,

j<__—————— 036191-01 (Upper Frame) cn

035936-01 (Ball)

036193-01 : 035937-01 der lt ® Ball Bearing)

035931-01

035938-01 (Whee!) LS (Roller Shaft)

75-0148 (2 PLACES) I (Washer)

75-044S (2 PLACES) 7 (Washer) ese) en 4 (2 PLACES) (Screw) A036096-01 (Harness)

036192-01 (Lower Frame)

03416801 —— a (Label—not —~| ‘A035220-01 showa for clarity) (PCB)

Figure 21 Mini-Trak Ball™ Assembly A036190-01 A

Page 47

Figure 21 Mini-Trak Ball™ Assembly Parts List “~S

Part No. Description A035220-01 Coupler PCB Assembly A036096-01 Harness Assembly 72-8406 #4-40 x %-Inch Hex Socket-Head Cap Alloy Steel Machine Screw 75-014S #4 Fiat Plain SAE-Standard Zinc-Plated Steel Washer 75-044S, #4 Zinc-Plated Steel Split Lock Washer 034168-01 Label with Lubrication Instructions

035931-01Roller Shaft(2 per assembly)

035936-01 Mini-Trak Ball™

035937-01Ball Bearing(6 per assembly)

035938-01 Etched Encoding Wheel 036191-01 Upper Black Plastic Frame 036192-01 Lower Black Plastic Frame

036193-01Idler Shaft(1 per assembly)

176010-106 #8 x %-Inch Cross-Recessed Pan-Head Thread-Forming Twin-Lead Zinc-Plated Steel Screw

Page 48

“Bosh Hii i cases 0" RRR (fesery a ES sina! Fen} perez] reed font

fi ms} § or o MING, T 8 9

c Figure 22 Centipede™ Game PCB Assembly A037241-01

Page 49

Centipede™/Cocktaii

Figure 22 Centipede™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) C012294-01 Audio 10 N-Channel MOSI/LSI Custom Chip (C3) 24-250106 10 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C83) 24-250107 400 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C52, 78) 24-500105, 1 mf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C79-82, 84, 86) 24-500106 10 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor (C85) 29.088 -1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 5-37, 40-51, 54-64, 66-77, 87, 88)

31-1N91475V Type-1N914 Switching Diode(CR1, 2)
31-1N400175V Type-1N4001 Switching Diode(CR4, 5)

33-2N3908 Type-2N3906 PNP Switching and Amplifying Transistor (Q3)

34-2N3904,Type-2N3904 NPN Silicon Transistor(Q1, 2, 4, 5)

34-2N6044 Type-2N6044 Darlington NPN Transistor (Q6-8)

37-LM324Type-LM324 Integrated Circuit(J10)
37-4584BType-4584B Integrated Circuit(F10, F11)
37-555,Type-555 Timer Integrated Circuit(A11)
37-74LS00Type-74LS00 Integrated Circuit(L8)
37-74LS04Type-74LS804 Integrated Circuit(K3)
37-74LS08Type-74LS08 Integrated Circuit(B7, K4)
37-74LS10Type-74LS10 Integrated Circuit{L3, K2)
37-74LS20Type-74LS20 Integrated Circuit(A7)
37-74LS32Type-74LS32 Integrated Circuit(A4, C5, E3, F3, J3)
37-74LS42Type-74LS42 Integrated Circuit(H3)

37-74LS74 Type-74LS74 integrated Circuit (D4, D11, M3)

37-74LS83Type-74LS83 Integrated Circuit(F6, H6)
37-74LS86Type-74S86 Integrated Circuit(E7)
37-74LS90Type-74LS90 Integrated Circuit(L2)

37-74LS139 Type-74LS139 Integrated Circuit (C4, J2) 37-74LS153 Type-74LS153 Integrated Circuit (C7, E8, K6, L6, M6, N6, P6)

37-74LS157Type-74LS157 Integrated Circuit(D7, D8, E11, F8, H8, J8, K8, PS)
37-74LS163A,Type-74LS163A Integrated Circuit(A5, B5, M2, N2, N3, P2, P3)
37-74LS166Type-74LS166 Integrated Circuit(H9, J9)

37-74LS174 Type-74LS174 Integrated Circuit (C6, D6, E6, J4)

37-74LS175,Type-74LS175 Integrated Circuit(A8, E4, M4, N4)
37-74LS191Type-74LS191 Integrated Circuit(B11, C11)
37-74LS244Type-74LS244 Integrated Circuit(B1, C1, H5)

37-74LS245 Type-74LS245 Integrated Circuit (E2) 37-74LS257 Type-74LS257 Integrated Circuit (D9, E10, K9, L9, P7, M8, M9)

37-74LS259Type-74LS259 Integrated Circuit(M10)
37-74LS273Type-74LS273 Integrated Circuit(B4, J6)
37-74LS373Type-74LS373 Integrated Circuit(J5)

37-74LS374 Type-74LS374 Integrated Circuit (H4)

37-74S04Type-74S04 Integrated Circuit(N1)
37-74S74Type-74S74 Integrated Circuit(E9, F9)

37-7407 Type-7407 Integrated Circuit (A9, A/B10) 37-7815 + 15V Voltage Regulator (VR2) 37-7915 -15V Voltage Regulator (VR1)

38-MV5053Type-MV5053 Light-Emitting Diode(CR3)

[Continued on next page]

a

Page 50

oN Centipede™/Cocktait

Figure 22 Centipede™ Game PCB Assembly, continued Parts List

Part No. Description (Reference Designations and Locations in Bold) 41-3003 100 uH, +5%, Hot-Moided Plastic Fixed R.F. Choke (L1-3)

62-001SPST Momentary Pushbutton Switch(Reset)

66-114P1T 4-Station, Single-Throw, Dual-Inline-Package Bit Switch (N11) 66-118P1T 8-Station, Single-Throw, Duat-Inline-Package Bit Switch (N8, N9)

79-4201616-Contact Medium-Insertion-Force Integrated Circuit Socket(P4)
79-42C2222-Contact Medium-Insertion-Force Integrated Circuit Socket(E5)
79-42C2424-Contact Medium-Insertion-Force Integrated Circuit Socket(F7, HiJ7, D1, E1, F/H1, J1)
79-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket(C2, C3)

81-4302 Nylon Snap-In Fastener

90-10212.096, + 005%, Crystal(¥1)

90-6013 Microprocessor (C2)

90-7005Random-Access Memory(C8)
90-7018Random-Access Memory(K5, K7, L5, 17, M5, M7, N5, N7)
90-7033Random-Access Memory(F2, H2)

020670-01 Test Point

110000-1021K Ohm, +5%, %W Resistor(R9-11, 13-16, 23-28, 31-38, 55-60, 67, 68, 77, 79, 80, 87-89, 94,

95, 99, 104, 109, 114-123, 134, 136-141)

110000-10310K Ohm, +5%, %4W Resistor(R1, 2, 6-8, 12, 17-22, 29, 30, 39-54, 70, 71)
110000-104110K Ohm, +5%, ¥4W Resistor(R81, 82, 105, 106)
110000-105100 MegOhm, +5%, %W Resistor(R5)

110000-152 1.5K Ohm, +5%, %4W Resistor (R108) 110000-221 220 Ohm, +5%, ¥4W Resistor (R3, 62, 64, 66, 72, 74-76, 78, 135) 110000-222 2.2K Ohm, +5%, %4W Resistor (R107)

110000-331330 Ohm, +5%, %4W Resistor(R61, 63, 65, 73)

110000-332 3.3K ‘Ohm, + 5%, VsW Resistor (R69, 83-86, 103, 130-133) 110000-471 470 Ohm, +5%, YW Resistor (R90-93, 96-98, 100, 110-113, 124-129, 142)

110000-56056 Ohm, +5%, %4W Resistor(R101, 102)
110000-56356K Ohm, +5%, %4W Resistor(R4)

122002-102 .001 uf Ceramic-Disc 50V Radial-Lead Capacitor (C4) 122004-224 .22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C65) 122005-103 .01 uf Ceramic-Disc 25V Radial-Lead Capacitor (C53) 128002-101 100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C1) 128002-221 220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C38, 39) 128002-390 39 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C2) 136001-201 or -211 136001-202 or -212 136001-203 or -207

136001-204 or -208 136001-205 or -209 136001-206 or -210 136001-213

137161-001

137169-001 137170-001 Read-Only Memory (F7) Read-Only Memory (H/J7) Read-Only Memory (01) Read-Only Memory (E1) Read-Only Memory (F/H1) Read-Only Memory (J1) Programmable Read-Only Memory (P4)

Type-ER2055 Integrated Circuit(E5)Note: If you replace this part, you must erase this ROM

before locking up the game. See Figure 6, Self-Test Procedure, in this manual for instructions. Type-74LS107 Integrated Circuit (L4)

Random-Access Memory(A6, B6)Acceptable substitute is part no. 90-7008 or 90-7035.
Page 51

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 52

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This ‘drawing 1s only conditionally issued, and neither receipt nor Possession thereof confers or transfers any right in, of li: ‘cense to use, the subject matter of the drawing or any de sign or technical information shown thereon, nor any night to reproduce this drawing or aay part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to repro: duce this drawing is granted or the subject matter thereot unless by written agreement with or written permission from the corporation. R33 = oe Gab 5 2

"le|cectiQ|
5]call)8a
~cR22rs
omGoac
C20cat0Rs

a cia N

—+3300|—

35V

—+$38+

i C23 c3l

35V.feiF-e222}

ArleF eR fe 22 p32 R25

oo-{4a5wtcee,C2

5.6K 08 ek y= =I 2812 7905

(@) R241, 2 Wr oO

TIP32_TOAZ002 4TDA2002A
BazNaco2z Q5\Qa?

cre {> 0 R527 ip + Is

See,C7 oDoe
S3IR3{_),,CeG|,,9|Cis
0cece{-|*parisJOO“Be cia
®Ri3toK|220 | R21 l/aw

0 4Jocaz yb

|5470

a DIR

4CcGoce!

470 ATR!

% y Cio

aSS00uF+-—

7 35V R30 2 cri Qn 1 Finacoz 0 oy co

vboSB3004F}—
4o35V

Figure 23 Regulator/Audio II PCB Assembly A035435-02 E

Page 53

Figure 23 Regulator/Audio il PCB Assembly Parts List

Part No. Description (Reference Designations and Locations in Bold)

12-52P72.7 Ohm, +5%, 1W Resistor(R5)

16-54P0 4 Ohm, +5%, SW Wirewound Resistor (R25) 19-100P1015 -1 Ohm, +3%, 7W Wirewound Resistor (R24)

19-3151021K Ohm Vertical PCB-Mounting Cermet Trimpot(R8)
24-2501081000 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C13)
24-250477470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C1, 4, 12)
24-35022622 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor(C24, 31)

24-350338 3300 uf Aluminum Electrolytic Fixed Axial-Lead 35V Capacitor (C9, 10, 18, 19)

24-5001051 uf Aluminum Electrolytic Fixed Axial-Lead 50V Capacitor(C22, 23)

29-088 .1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, 11, 20, 21)

31-1N4002100V 1-Amp. Silicon Rectifier Type 1N4002 Diode(CR1, 4)
31-1N5401100V 3-Amp. Silicon Rectifier Type 1N5401 Diode(CRS5-8)
33-TIP32PNP Power Transistor, Type TIP32_(Q2)
34-2N3055NPN Silicon Transistor, Type 2N3055(Q3)
37-LM3055V Linear Voltage Regulator(Q1)
37-7812+ 12V Voltage Regulator, Type 7812(Q8)
37-7905— 5V Voltage Regulator, Type 7905(Q9)

72-1608C #6-32 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw 72-6606S #6 x %-Inch Pan-Head Thread-Forming Cross-Recessed Type-AB Zinc-Plated-Steel Screw (Q8) 75-F60405 #6-32 x Ya-Inch Binder-Head Nylon Screw (Q5, 7) 75-99516. #6-32 Nut/Washer Assembly

78-16008Thermally Conductive Compound(Q3)

78-16014 Thermally Conductive Silicon Insulator (Q2, 9)

79-583066-Position Connector Receptacle(J6, 9)
79-583089-Position Connector Receptacle(J7)
79-5834612-Position Connector Receptacle(J10)
79-583544-Position Connector Receptacle(J8)

020670-01 Test Point 034531-01 Heat Sink

100015-103.01 uf Ceramic-Disc 25V Radiai-Lead Capacitor(C5, C14)
110000-0101 Ohm, +5%, YW Resistor(R10, 19)
110000-10010 Ghm, +5%, %W Resistor(R11, 20, 29, 30)
110000-101100 Ohm, +5%, %4W Resistor(R4, 12, 22)
110000-1021K Ohm, +5%, Y4W Resistor(R27, 28)

110000-103 10K Ohm, +5%, Y4W Resistor (R13, 14)

110000-271270 Ohm, +5%, %W Resistor(R1)
110000-33033 Ohm, +5%, %4W Resistor(R3)
110000-3923.9K Ohm, +5%, YW Resistor(R6)
110000-5625.6K Ohm, +5%, %4W Resistor(R32, 33)

110000-752 7.5K Ohm, +5%, YW Resistor (R7) 110001-221 220 Ohm, +5%, Y2W Resistor (R9, 21) 116000-220 22 Ohm, +5%, 10W Wirewound Resistor (R31)

122602-102001 uf Ceramic-Disc Minimum 25V Radial-Lead Capacitor(C2, 7, 16)
122004-224.22 uf Ceramic-Disc 25V Capacitor(C6, 8, 15, 17)
137151-002Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit(Q5, 7)
Page 54

Centipede™ Cocktail

79-4411001 (Fuse Post) 034544-01 46-2017002 (Fuse Biock Cvr.) (Fuse)

034482.02 (Chassis) A035674.01 79-3206 (Volt. Plug Assy.) (Fuse Block) A034623-03 (Power Supply Harn. Assy.)

78-2708 (Bushing)

TOP VIEW NOTICE TO ALL PERSONS RECEIVING THIS DRAWING (Bracket) CONFIDENTIAL: Reproduction, forbidden without the spe 29-053 Gific written permission of Atari, Inc., Sunnyvale, CA, This irawing is Only conditionally issued, and neither receipt nor (Elec. Cap.) possession thereof confers or transfers any right in, or li- Cense 0 use, the subject matter of the drawing or any design of technical information shown thereon, not any right to reproduce this drawing or any part thereot. Except tor manufacture by vendors of Atari, Inc., and for manufacture under the cerporation’s written license, no Tight is granted 442001.001 ie reproduce is drawing or the sleet mater theft Ur less by written agreement with or written permission from (Transformer Only) the corporation. BOTTOM VIEW A006555-01 (Rect. PCB Assy.)

A034630-01 79-15021001 (RFI Filter) lock)

‘4034629-01 (AC Harness Assy.)

Figure 24 Power Supply Assembly for Color Raster-Scan Games A036099-01 A

Page 55

Figure 24 Power Supply Assembly for Color Raster-Scan Games Parts List

Part No. Description A006555-01 Rectifier Printed Circuit Board Assembly A036098-01 Transformer and Harness Assembly (includes shielded power transformer) (T1) A034629-01 AC Harness Assembly A034630-01 RFI Filter Assembly (FL1) A035674-01 Voltage Plug Assembly (set of four plugs) 29-053 26,000 uf 15V Electrolytic Capacitor (C1) 46-2013002 3-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F4-F6) 46-2017002 7-Amp. 250V 3AG Slow-Blow Glass Cartridge-Type Fuse (F1-F3) 78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x °%,-Inch Outside Diameter x Ya-Inch Thick 78-70501SC. 2-Inch-Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 §-Position 3AG Fuse Block with ¥%-Inch Quick-Disconnect Terminals 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-02 Metal Power-Supply Chassis (acceptable substitute is Atari part no. 034482-01) 034544-01 Fuse Block Cover 142001-001 Shielded Power Transformer Only (with isolation windings)

Page 56

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING 99-15038 CONFIDENTIAL: Reproduction forbidden without the spe- 99-15001 thru 99-15017 (Bezel tor Button) cific written permission of Atari, Inc., Sunnyvale, CA. This (Ret. Button) drawing is only conditionalty issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any de- ‘sign or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors af Atari, Inc., and for manutacture under the corporation's written license, no right is granted to reproduce this drawing oF the subjeci matter thereot, unless by written agreement with of written permission from the corporation.

99-15052 (Spring for Button) 99-5051 (Lamp Holder) a

, L a : 99-15040 <a % _— 99-15026 (Lever) (Coin Inlet) 99-15056 (Screw for Bezel)

99-15039 (Coin intet) (Bezel for Cover)

PART OF “nen,

99-15041 99-15055 t : 99-15041

(Retng. Screw) al. (Lockout Coil)

Yor 99-15053 (Lockt, Coil Spring) 99-15054 (Pivot for Lever) 99-15027 (Coin Ret. Box)

l~+——— 99-15028 (Coin Ret. Box)

99-15037 (Sw. Adjuster) 99-15056 (Screw for Bezel)

99-15029 (Bracket)

99-15042. 99-15060

(Switch) A036597-01

a (Sw. Cover)

(Harness—not shown for clarity)

Figure 25 Double Coin Acceptor/Mount Assembly A036693-01 thru -20 c

Page 57

Figure 25

A036693-.01 — U.S. 25¢/25¢ Coin Door A036693-02 — U.S. 50%/50¢ Coin Door A036693-.03 — British 10 P/10 P Coin Door ‘A036693-04 — British 10 P/50 P Coin Door 403669305 — British 20 7/50 P Coin Door ‘A036693-06 — German 1 DM/ DM Coin Door 03669307 — German 2 DM/1 DM Coin Door Double Coin Acceptor/Mount Assembly Parts List

‘A036683-08 — German 2 DMIS OM Coin Door ‘4036693-09 — German 1 DMS DM Coin Door ‘A036693-10 — Belgian § Fri5 Fr Coin Door ‘A038693-11 — French 1 Fr/1 Fr Coin Door ‘A036693-12 — French 2 Fr/1 Fr Coin Door ‘A036693-13 — Swedish 1 Kri1 Kr Coin Door ‘A036683-14 — Hong Kong $1/$1 Coin Door A036693-15 — Canadian 250/25¢ Coin Door A036693-16 — Spanish 25 Pts/25 Pts Coin Door A036693-17 — Swiss 1 Frit Fr Coin Door ‘A036693-18 — Italian 100 1/109 | Coin Door ‘A036693-19 — Japanese 100¥/100Y Coin Door A036693-20 — Australian 20/20% Coin Door

Part No. Description A036597-01 Double Coin Acceptor Harness Assy. 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15012 Coin Return Button with U.S. 50¢ (2 x 25¢) Price Plate 99-15013 Coin Return Button with British 20 Pence Price Plate 99-15014 Coin Return Button with British 50 Pence Price Plate 99-15015 Coin Return Button with French 2 Franc Price Plate 99-15016 Coin Return Button with Swiss 1 Franc Price Plate 99-15017 Coin Return Button with Hong Kong $1 Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15030 Flap for Lockout Coil U.S. 25¢) 99-15036 Coin Return Cover 99-15037 Switch Adjuster 99-15038 Bezel for Coin Return Button 99-15039 Bezel for Coin Return Cover 99-15040 Coin Return Lever 99-15041 Lockout Coil 99-15042 Coin Switch for U.S. 25¢ 99-15051 Lamp Holder 99-15052 Spring for Coin Return Button 99-15053 Spring for Lockout Coil 99-15054 Pivot for Coin Return Lever 99-15055 Retaining Screw 99-15056 Screw for Both Bezels 99-15060 Switch Cover

Page 58

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 59

YOUR COMMEN TS, PLEA SE! Centipede™/Cocktail 1st printing

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply

Name.

Firm O Distributor

Address C Operator City State Zip C Other. Area Code Phone

Page 60

First told

BUSINESS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States

Page 61

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 62

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 63

En Aen RES RN REN BE BE RES Bea a

Warranty

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty

  • days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is prompily notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Sellers’ plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.

Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

This document is and contains contidential trade secret information of Atari, Inc.

This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.

Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.

Page 64

AN ATARI

ATARI INC 1265 BORREGAS AVENUE P.O. BOX 427 SUNNYVALE, CALIFORNIA 94086 408/745-2000 * TELEX 35-7488