CATHODE RAY TOMES

VS Tennis

Vs. Tennis (Japan/USA, set TE A-3) (Nintendo Co., Ltd., 1984) · Document · 4 pages · 2 sections · original scan

Page 1

VSTENNIS |

(Operation Manual)

|. How to install Software ROMs

Each Software ROM is labeled with a Location Number shown on it (QWWShaded Portion illustrated below), which will indicate the corresponding location on the P.C. Board where it should be installed.

(Label on Software ROM)

The VS Tennis Game contains 12 Software ROMs, which have location numbers, 1A, 1B, 1C, 1D, 2A, 28, 6A, 6B, 6C, 6D, 8A, and 8B. Each ROM must be mounted into the proper IC Socket.

© ABCD E FH JI KLM N PR

CAUTION: Make sure the Software ROMs are inserted properly (Notice the notch is in the upper end, all notches should be facing the same direction) Ad9-10-SAN

ROM Locations on P.C. Board

Caution: If other Software ROMs are already mounted in the P.C. Board, the new Software ROMs should be mounted after the old software ROMs are removed from the IC Socket.
Page 2
  • Points and methods of adjustment

MDS P.C. Board Game Option Settings

os Leu LS Switch (SW1) Settings cjca 1,2], 3]4{[5{[6f[7]8

DifficultyEasy1 | OFF | OFF

2| OFF | ON

Mos-9PU)VS. ComputerJ3] ON | OFF

Hard 4) ON | ON

DifficultyEasy1OFF | OFF

2 OFF | ON

1234567812345678Vor Petar13oy | Oe
Hard4ON | ON

Racket Size Large OFF

Small ON

Extra Score1SetOFF

1 Game ON Court Color Green OFF Blue ON NINTENDO JAPAN (TITLE DISPLAY) USA

Switch (Swe) Settings fife, s [ais [et 7|s Game Mode OFF | Test Mode ON,

Coin/Creditwi |OFF | OFF

1/2 OFF | ON 2 ON | OFF |

—FREEon | on]
Game ModeAOFF | OFF
Refer toBorF | ON
table below Cc|ON | OFF
o |7_|-ON | on |
Number of3|OFF | OFF
Rackets4|orr | ON
Per Game5on | one

Attract. No Music | OFF

MusicMusic|ON

Game Mode

ABCcip}

are 1 credit | 1 Credit | 1 Credit | 1 Credit

(VS - Computer)ealediediedi

Doubles

(VS « Computer)1 Credit2 Credit1 Credit2 Credit

Singles (VS : Person) 2 Credit | 2Credit | 2 Credit | 2 Credit Doubies

(VS - Persons)2 Credit2 Credit4 Credit|, 4 Credit
Page 3
  • Test Mode
  • Entering Test Mode

Make sure the main power switch is in “OFF” position. Set for Test Mode by the switching toggle 1 (SW2) on the game P.C. Board to the “ON” position, and then turn the main power switch to the “ON” position.

  • Memory Test

All ROM and RAM will be tested automatically, and the test result will be displayed on the Video Monitor, with Green meaning “OK”, Red meaning “NG”, and Yellow meaning “NOT IN IC SOCKET”. Also, the memory back-up condition can be tested, and the result will be displayed on the Video Monitor as a Battery illustration. On power up, “BATT” section will be Red. Turn the power off for 5 seconds, then turn back on. “BATT” section will now be Green if good, and still Red if no good. Pressing the Service Switch will step to the next test. (“Switch Test”)

at) | [ves sa] [| za] [ta (res j (ee | [28 ve] | se] [se] [ 26 re] |) Ce} Coe} ze} Leet | ee fel |} at MEMORY TEST |

  • Switch Test

All Control Levers, Game Buttons, and Dip Switchs can be tested at this time. The screen should show a picture of the control lever and the game buttons, along with the Dip switch The picture corresponding to the switch being tested will appear GREEN if in the “OFF” position, and RED if in the “ON” position. Pressing the service switch will step to the next test. (CRT & Sound Test)

SWITCH TEST J #|

C

Page 4
  • CRT and Sound Test
  • CRT Test The test pattern shown in Fig.1 will appear on the screen. This pattern is used for adjusting color convergence. Moving a control lever up or down will change the test pattern to an all white screen shown in Fig. 2. This pattern is used for adjusting color purity. (screen should be pure white.) Moving the control lever again will put the first pattern back on the screen, if desired.
  • Sound Test The different sound circuits can also be tested at this time. Pressing a “B” button or a “1” or “3” button will start a corresponding sound test. To stop the test, press the “A” button or the “2” or “4” button.

WHITE BALANCE ah eae

Fig. 1 Fig. 2

  • Return to Game Mode

Turn the main power switch to “OFF” position. Reset back to “Game Mode” by switching Toggle 1 (SW2) on the P.C. Board, back to the “OFF” position, and then turn the main power switch to the “ON” position.