CATHODE RAY TOMES

Black Widow SP-234 1st Printing

Black Widow (Atari, 1982) · Schematic Package · 23 pages · 96 sections · original scan

Page 1
Scan of page 1

Table of Contents

Sheet 1A Table of Contents Sheet 1B Black Widow Main Wiring Diagram (039988-01 A) Sheet 2A Color X-¥ Power Supply Wiring Diagram (037394-01 B), Regulator/Audio Il PCB Schematic Diagram (035435-02 G) Sheet 2B Coin-Door Wiring Diagram (037542-01 E), Utility Panel Wiring Diagram (038004-01 F), Fluorescent Light Wiring Diagram (035833-01 A) Sheet 3A Black Widow Memory Map Sheet 3B- —_ Black Widow PCB Signal Name Descriptions 5A Game PCB Schematics (040003-01A), Sheets 5B-11A

Sheet 5B Power Input, Clock, Power-On Reset, Watchdog Sheet 6A Test Connector, Microprocessor, Timing Diagram, and Address Decoder Sheet 6B Read-Only Memory, Random-Access Memory, High-Score Table Sheet 7A Coin Door and Control Partel Input, Option Switch Input and Audio Output, Coin Door and Control Panel Output Sheet 7B Vector Address Decoder, Vector Address Selector, Vector Read-Only Memory, Vector Random-Access Memory, Vector Memory Data Buffer Sheet 8A Vector Data Shifters, Op Code and Intensity Latches Sheet 8B State Machine Clock Logic, State Machine Clock, State Machine, Decoder Disable, Address Controller, Signature Analysis Flag’ Sheet 9A Normalization Flag, Center Flag, Vector Flag, Halt Flag, Go Flag, Vector Scaling, Vector Timer Sheet 9B Z Intensity and Blanking, R-G-B Output Sheet 10A DAC Reference and Bipolar Current Sources, X-Axis Output Sheet 10B Y-axis Output, Adjusting X- and Y-Axis Video Potentiometers

NOTE This staple temporarily holds the schematic package together. Remove the staple before using the

schematics. Sheet 11A Amplifone Deflection PCB Schematic Diagram (201014-XX A) Sheet 11B Amplifone Main Wiring Diagram (200000-01 B), Amplifone High-Voltage PCB Schematic Diagram (201012-XX A) Sheet 12A Wells-Gardner Color X-Y Display Schematic Diagram (92-053) Operators Manual

A ATARI ‘Avwarne! Communcations Company sp2se 1A © ATARIINC.1983. 1st printing

Page 2
Scan of page 2

This page is a drawing, shown as the original scan.

Page 3
Scan of page 3

This page is a drawing, shown as the original scan.

Page 4
Scan of page 4

Utility Pane! Wiring Diagram

Coin Door Wiring Diagram

20 oR RIGHT Ct Sw. ‘es 55 rico gs on 8k LEFT COINSW. ‘Sw. GND

RIGHT COIN SW. DOE RIGHT in 4001 | LOCKOUT COIL ‘ ow EFT COIN certeey

RIGHT LOCKOUTCOIL LEFT LOCKOUT COIL

+1OVDC

6.3 VAC

63 VAC

CHASSIS GND. LEFT LOCKOUT COIL OSTAHRYW HR —

14001 (2ptcs)

Lerr

COIN COUNTER

Fluorescent Light Wiring Diagram

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereo! MS VAC confers or transfers any right in, or license to use, the subject mat ter of the drawing or any design or technical information shown ® thereon, nor any Night to reproduce this drawing or any part thereo!

Except for manulacture by vendors of Alar, Ine., and for manutac:

{ure under the corporation's written licenss, no right is granted to reproduce this drawing or the subject matter thereof, unless by witten agreement with or written permission Irom the corporation.

Black Widow Game Wiring Interfaces

© ATARI INC., 1985 ‘SP-234 Sheet 2B QA rar06: communicarons Company 1st printing

Page 5
Scan of page 5

i DECIMAL ADDRESS BUS

ADDRESS | A15 A14A13 A12A11A10 A9 AB A7 AB AS A4 A3 A2 Al D7 D6 D5 DS D3 D2 01 000-EFFF D000-DFFF C000-CFFF B000-BFFF ‘A000-AFFF 9000-9F FF

CABINET 1

START 2

START 1 FIRE UP

SPARE

FIRE DOWN

FIRE LEFT

FIRE RIGHT

SPARE WT WDCLR EAROMWR EAROMCON INTACK VORST #8 )

iy elooccc0000 elooc0cc00 elocoac00n0 olonasco+Hs elooccc00c0 elooossi4 °

PLAYER 2 LED PLAYER 1 LED COIN LOCKOUT BANK SEL COIN CNTR-L COIN CNTR-R

OPTION 2 OPTION 1 OPTION 0 SPARE

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specitic writ. ten permission of Atari, Inc., Sunnyvale, CA. This drawing is only Conditionally issued, and neither receipt nor possession thereot Confers or transters any right in, or license to use, the subject matjon shown 8940 8900 88CO 8880 8840

ter of the drawing or any design or technical it hereon, nor any right 10 reproduce this drawin, ® ! Except for manufacture by vendors of ture under the corporation's written licen: reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation. oS0O+0+400- CO=>PPO+0 oceo00000000 oo00000000 oo00000000 ovo0000000 ooo0000000 oeo00000000 ooo0000000 eo00000000j0 Black Widow Memory Map

© ATARI INC., 1963 vere: conmanesions Comoany

Page 6
Scan of page 6

Descriptions of Black Widow Printed Circuit Board Names

A10, A13-A15 Address bits on Microprocessor Address Bus lines A10 and A13A15 are generated by Microprocessor C2. Bits on lines A13-A15, together with those on AB11-AB12, are the input bits to Address Decoders R1-R2. A10 is exclusive-ORed with BANK SEL by gate B6 to produce the A10 input bit for Random-Access Memory N/P1.

‘ABO-AB12 Address bits on Buffered Microprocessor Address Bus lines ABO-AB12 are software-generated by Microprocessor C2 and buf-

fered by B1 and C1. These signals are the input bits to Read-Only

Memories D1, E/F1, H1, J1, K/L1, and M1; and to Random-Access Memory N/P1. Address bits AB6-AB8 are the select input signals for Address Decoder P3. Address bits AB11-AB12 and A13-A15 are the Input bits for Address Decoders R1 and R2. Address bits ABO-AB13 are applied with bits from AVGO-AVG12 to Vector Address Selectors K8, M8, L8, and N8 to produce the data on lines AMO-AM12. Bits ABO-AB3 are control signals to custom audio chips B3 and C/D3 In the Option Switch Input and Audio Output circuit. Bits ABO-AB5 are the input signals to latch P2 In the High-Score Table circuit where they are used to produce the A1-A5 address Input for EAROM M2.

ABts KXBiG Is from AB13, inverted by J3, and applied to Vector Ad-

dress Selector M8. When VMEM Is iow, AB13 and AB12 select the

specific Vector Memory Read-Only Memory.

AMO-AM13 Address bits on Multiplexed Address Bus lines AM0-AM13 are software-genecsted by Vector Address Selectors KB, LB, MB, and

  • When [s low, the Multiplexed Address Bus Is from Buffered Mi Address Bus ABO through AB12 and ABT3.

When is high, AMO-AM12 Is from Vector-Generator Address

Bus lines AVGO-AVG13. ‘Signals AMO-AM11 are the input address signals to Vector Read- Only Memories L7, M/N7, N/P7, R7 and to Vector Random-Access Memory K7. In addition, AM11-AM13 are the select input signals for Vector Address Decoder J7. AMO-AM7 are input signals for multiplexers N3 and R3 of the State Machine circuit.

AUD 1-AUD 2 The Audio 1 and Audio 2 signals are game PCB output signals that are generated by custom audio chips B3 and C/D3 of the Optlon Switch input and Audio Output circuit. AUD 1 Is the inverse of AUD 2. These signals are applied to the Audio/Regulator Il PCB and ultimately drive speakers 1 and 2.

AVGO-AVG13 Address bits on Vector-Generator Address Bus lines AVGO- AVG13 are software-generated by Vector Address Controller J9. When VMEM Is high, these signals are passed through the Vector Address Selectors on lines AMO-AM13 to the Vector Read-Only Memory and the Vector Random-Access Memory.

BANK SEL The Bank Select signal is developed from data on line DB2. When latch R9 of the Coin Door and Contro! Pane! Output circuit is clocked by LATCH, R89 latches the data on DB2 to pin 2 of R9, Producing the BANK SEL signal. BANK SEL is exclusiveORed with the address bit A10 by gate 56 to produce input address bit A10 for Random-Access Memory N/P1. BLANK Blank is an active high-level signal generated by counter M3 in the Z Intensity and Blanking circuit and ORed with Z BLANK by gate MS of the R-G-B Output circuit. When high, BLANK turns off transistors Q6, Q8, and Q10, which kills the RED, GREEN, and BLUE output signals to the display.

BLUE Blue Is a game PCB output signal developed from the data on line DVYO. When the data bit on DVYO Is high and latch K10 of the R-G-B Output circult Is clocked by STATCLK, the data on DVYO is Inverted and latched to pin 11 of K10. If both BLANK and Z BLANK are low, this data bit Is again inverted by gate L10 to tum on Q10. Transistor Q10 generates the BLUE signal for the display.

BUFFEN Buffer Enable Is an active low-level signal developed from BO2 by Vector Address Selector K8. BUFFEN is the enable input signal {or heer dats Data Buffer P8. When low, BUFFEN allows P8 to pass data.

Be2 The active high-level Phase 2 Clock signal is hardware-generated from the intemal clock circuitry of Microprocessor C2, buffered by B1, and applied to AND gate K4. Gate K4 ANDs together

862, RWB, and 3 MHz to produce WRITE. B42 Is also used as the

clock signal for custom audio chips B3 and C/D3 of the Option ‘Switch Input and Audio Output circult.

Be2

The active low-level Phase 2 Clock signal is generated at pin 12

of F3 by inverting B¢2. BO Is applied to Vector Address Selector KB to produce BUFFEN. CENTER Center_is an activetow level signal software-generated. ‘gating CNTR with HALT by Center Flag gate L6. When low, CEN- R closes switches E10 of the Y-Axis Output circuit and B10 of the X-Axis Output circult to center the beam on the display.

CNTR The active high-level Center Flag signal is software-generated by latch_E5 of the Center Flag circult. CNTR is set high when VGCK, and OP2 are low CNTR Is applied to gate J5 of the Normalization Flag circuit to develop the clear signal for latch BO can rm witn VOT by GO Flag gate M6 to: generate the nal.

CNTR The active low-level Center Flag signal Is software-generated by latch E5 ot the Center Flag circuit. When clocked by the 12-MHZ signal, E5 latches STOP to pin 9 to produce CNTR. CNTR Is gated with HALT by Center Flag gate L8 to generate CENTER. COIN CNTR-L Coin Counter Left Is a game PCB output signal developed from the data bit on line DB1. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circult latches the data bit on DBI to pin 6 of R9. From here, the signal Is current amplified and Inverted by Q4 and applied to the game Utility Panel to activate the Left Coin Counter.

COIN CNTR-R Coin Counter Right is a game PCB output signal developed from the data bit on line DBO. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on DBO to pin 5 of R9. From here, the signal is current amplified and Inverted by Q3 and applied to the game Utility Panei to activate the Right Coin Counter. COIN LOCKOUT Coin Lockout Is a game PCB output signal developed from the data on line DB3. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on DB3 to pin 9 of R9. From here, the signal is current amplified and inverted by Q2 and applied to the Right and Left Lockout Coils of the game Coin Door.

DO-D7 Microprocessor Data Bus lines D0-D7 form a bi-directional data bus between the Microprocessor, the Read-Only Memory, and the Option Switch Input circuits.

DBO-DB7 Buffered Microprocessor Data Bus lines DBO-DB7 form a buffered bi-directional data bus between microprocessor data-bus buffer F2 and Vector Memory Data Buffer P8; Coln-Door and Control Panel Input circuit buffers L9, M9, and N9; High-Score Table latches K2 and J2; and High-Score Table buffer H2.

DIS DAT Disable Data Is an active_low-level signal generated by test equipment connected to the DIS DAT test point. DIS DAT Is ANDed with the ROM signal by gate E3 to produce the enable signal for buffer £2 of the Read-Only Memory circult. When enabled, buffer E2 passes data from the selected Read-Only Memory to the Microprocessor Data Bus.

DISRST Display Reset Is an active low-level signal software-generated by gate L6 of the Halt Flag circult. When either RESET or VGRST Is low, DISRST Is set low When low, DISRST clears State Machine latch P4, DAC Reference and Bipolar Current Sources latch E8, R-G-B Output latch K10, Vector Scaling latch D7, Z Intensity and Blanking latch E6 and counter M3. In addition, DIS Presets the HALT signal from latch L5 to the high level.

DVG@O-DVG7 Data bits on Vector-Generator Data Bus lines OVGO-DVG7 are software-generated by the selected Vector Read-Only Memory or Vector Random-Access Memory. If Vector Memory Data Buffer P8 Is enabled (BUFFEN Is low) and the R/WB line is low, the data on lines DVGO-DVG7 Is passed through P8 to the Buffered Microprocessor Data Bus to be read by the microprocessor. Otherwise, the data on DVGO-DVG7 Is sent to the Vector Data Shifters and to the Op Code and Intensity Latches. .

DVX3-DVX12, DVX12 Data bits on X-Axis Vector Data lines DVX3-DVX12 and DVX12 are software-generated by Vector Data Shifters A8, B8, C8, and by latch C8 of the Op Code and Intensity Latches circuit. DVX3- DVX11 and DVX12 are the input signals to digital-to-analog converter (DAC) A/B9 of the X-Axis Output circuit. The data carried on these lines represents the X-axis change from the current location of the display beam. If DVX12 is low, DAC A/B9 operates only in its

ATARI lower 512 positions, which means a negative direction of change ‘on the display. If DVX12 is high, DAC A/B9 operates only in its upper 512 positions for a positive direction of change on the display. In addition, DVX11 and DVX12 are exclusive-ORed by gate B6 of the Normalization Flag circult.

DVYO-DVY12, DVY12 Data bits on Y-Axis Vector Data lines DVYO-DVY12 and DVY12 are software-generated by Vector Data Shifters F8, H8, J8, and by latch D6 of the Op Code and Intensity Latches circuit. DVY3- DVY11 and DVY12 are the input signals for digital-to-analog converter (DAC) F9 of the Y-Axis Output circult. The data carried on these lines represents the Y-axis change from the current location of the display beam. If DVY12 is low, DAC F9 operates only in its lower 512 positions, which means a negative direction of change ‘on the display. If DVY12 Is high, DAC F9 operates only in its upper 512 positions for a positive direction of change on the display. In addition, DVYO-DVY7 are applied to latch E8 in the DAC Reference and Bipolar Current Sources circuit. These signals, together with VCTR and VCTR, set the X REF and Y REF voltage levels (via DAC D9). Lines DVYO-DVY2 carry data representing the eight different color signals for latch K10 of the R-G-B Output circuit. Lines DVY4-DVY7 carry data representing the Z-intensity signals for latch E6 of the Z Intensity and Blanking circuit. Data on DVY8-DVY10 are applied to latch D7 of the Vector Scal- Ing circuit. The data carried on these lines represents the number (in binary) that the Vector Scaling circuit uses to divide into the vector drawing time. The vector drawing time n Is divided by 2, where n equals the number represented on DVY8-DVY10. In addition, DVY11 and DVY12 are exclusive-ORed by gate B6 of the Normalization Flag circuit.

EAROMCON The Electrically-Alterable ROM Control signal is an active lowlevel signal software-generated by Address Decoder P3 at address 8900. ERROMCON is the clock signal for latch K2 In the High- Score Table circuit. EAROMCON allows K2 to pass data bits on lines DBO-DBS to the control lines of EAROM M2.

EAROMRD The Electrically-Alterable ROM Read Enable is an active lowlevel signal software-generated by Address Decoder R2 at address

  • 7000. EAROMRD Is the read-enable signa! for buffer H2 of the High-Score Table circuit. EAROMRD allows the eight data bits from EAROM M2 to be passed through buffer H2 to the microprocessor data bus.

EAROMWR The Electrically-Alterable ROM Write Enable Is an active low- ‘evel signal software-generated by Address Decoder P3 at address 8940. is the aon for latches J2 and P2 in the HighScore Table circuit. allows address bits on lines ABO-AB5 and data bits on lines DBO-DB7 to pass to the address and data input pins of EAROM M2.

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof conters or transfers any right in, or license to use, the subject mat ter of the drawing or any design of technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except ior manufacture by vendors of Atari Inc., and for manufac: lure under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation

Black Widow PCB Signal Name Descriptions

© ATARIINC., 1983 SP.234 Sheet 3B

Page 7
Scan of page 7

Black Widow PCB Signal Name Descriptions, cont.

ENORM The active low-level Normalization Flag Is software-generated by gate K4 of the Normalization Flag circuit. If OPO is high, SA is high, and the output from gate J5 is high, ENORM is set low when

STROBEO goes high. ENORM Is applied through gate E7 to the S1

input_pins of Vector Data Shifters A8, B8, C8, F8, H8, and J8. ORM multiples the rate of change of the X and Y vector data in the Vector Data Shifters (via shift left operations) at the same 2 factor specified by data on lines DVY8-DVY10. The n number is incremented at a 12-MHz rate until either DVX11 or DVY11 changes state, which then sets ENORM to the high level.

Go The Go flag is an active high-level signal software-generated by gate M5 of the Go Flag circuit when either VCTR or CNTR are high. GO is gated with HALT* by gate N5 of the State Machine cir-

fat to produce the A7 input address bit for State Machine ROM

GO Is also used as the enable signal for Vector Timer R6. When. GO Is high, the Vector Timer starts its count. The Vector Timer counts to 256 If OP1 Is high and OP1 is low If OP1 Is low and OP1 is high, the Vector Timer counts to 16K.

GREEN Green is a game PCB output signa! developed from the data on line DVY1 In the R-G-B Output circult. When DVY1 Is high and latch K10 is clocked by STATCLK, the data bit on DVY1 Is inverted and latched to pin 6 of K10. If both BLANK and Z BLANK are low, this data bit is again inverted by gate L10 to tum on Q8. Transistor Q8 generates the GREEN signal for the display.

HALT The active high-level Halt Flag is software-generated by latch L5 of the Halt Flag circuit. HALT is applied through buffer M9 of the Coin Door and Control Panel Input circuit (when SINP1 is low) to permit Microprocessor C2 to read the status of HALT on line DB6. In addition, HALT Is applied to latch P4 of the State Machine circult to develop HALT*.

HALT* The active high-level Delayed Halt Flag Is software-generated by latch P4 of the State Machine circuit. HALT* Is generated when the HALT signal has been delayed by one pulse of inverted VGCK (1.5 MHz), which in tum has been delayed by one pulse of 12 MHz. HALT* Is ORed with GO by gate N5 of the State Machine circuit to Produce the A7 Input address bit for State Machine ROM N4.

HALT The active low-level Halt Flag Is software-generated by latch L5. of the Halt Flag circuit. HALT Is the clear signal for Vector Flag latch E5 and Center Flag latch E5. In addition, HALT is ORed with CNTR by gate L6 of the Center Flag circult to produce .

INTACK Interrupt Acknowledge is an active low-level signal softwaregenerated from Address Decoder P3 at address 88C0. This signal Is an acknowledgment from Microprocessor C2 that an interrupt request has been received. INTACK resets counter J4.

INVERT X Invert X is an active high-level signal developed from the data bit on line DB6. When clocked by H, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on DB6 to pin 12 of R9. When high, INVERT X closes switch B10 through inverter K9 in the X-Axis Output circuit. This inverts the X-axis vector instruction to the display. INVERT Y Invert Y is an active high-level signal developed from the data bit on line DB7. When clocked by H, ‘atch R9 of the Coin Door and Control Panel Output circuit latches D87 to pin 15 of R9. When high, INVERT Y closes switch E10 through inverter K9 in the Y-Axis Output circuit. This inverts the Y-axis vector instruction to the display.

lo The Input/Output signal Is an active low-level signal softwaregenerated by Address Decoder R2 during addresses 8000 through 8FFF. I6 is gated with R/WB by gate J6 to produce the direction signal for bi-directional data buffer N9 of the Coin Door and Control Panel Input circuit. [0 determines the direction of data flow through buffer N9.

wos TOS Is an active high-level signal software-generated from Address Decoder R2 during addresses 6000 through 6FFF. The 0S. ‘signal Is ORed with the ROM signal by gate R4 to enable bi-directlonal data bus buffer F2 to pass data. When I/OS Is high, data buffer F2 Is tumed off, which allows custom audio chips B3 and C/D3 to pass data to the data bus.

Too 1700s an active low-level signal software-generated by Address Decoder R2 at address 6800. 1/00 Is the chip-select enable for cuson sudo chip C/D3 in the Option Switch Input and Audio Output circuit.

T0i ‘T(01 Is an active low-level signal software-generated by Address Decoder R2 at address 6000. ls the chip-select enable for cus-

brs eudo chip B3 in the Option Switch Input and Audio Output

circult.

LATCH Latch Is an active low-level signal generated by Address De-

coder P3 at address 8800. LATCH Is the clock signal tor latch R9 in

the Coin Door and Control Pane! Output circult. When low, LAT

allows the data bits on lines DBO-DB7 to pass through R9.

LATCHO Latch 0 Is an active low-level signal_software-generated by decoder H7 of the State Machine circuit. LATCHO Is applied through Inverter F7 to the SO Input pins of shift registers F8 and J8 In the Vector Data Shifters circuit. LATCHO causes the data bits on lines DVGO0-DVG7 to be latched by F8 and J8 to lines DVY0-DVY7 when F8 and J8 are clocked by the 12-MHz clock signal.

LATCHi Latch 1 Is an active low-level signal software-generated by decoder H7 of the State Machine circuit. LATCH1 Is applied through inverter F7 to the SO input pin of shift register H8 in the Vector Data Shifters circuit. LATCH1 causes the data bits on lines DVGO- DVG3 to be latched by H8 to lines DVY8-DVY10 when HB Is clocked by the 12-MHz clock signal. LATCH is also the clear signal for Vector Data Shifters A8, B8, C8, F8, J8, and for Op Code and Intensity Latch C8. In addition, LATCH1 is the clock signal for Op Code and Intensity Latch Dé. Whan LATCH goes low, the data bits on lines DVG4- 0VG7 are latched by D6 to lines OPO-OP2, OPO-OP2, DVY12, and BVY?2. LATCH2 Latch 2 is an active low-level signal _software-generated by decoder H7 of the State Machine circuit. LATCH2 is applied through inverter F7 to the SO input pins of shift registers A8 and C8 in the Vector Data Shifters circuit. LATCH2 causes the data bits on lines DVGO0-DVG7 to be latched by A8 and C8 to lines DVX3-OVX7 when A8 is clocked by the 12-MHz clock signal.

LATCHS Latch 3 is an active low-level signal software-generated by decoder H7 of the State Machine circult. LATCH is applied through inverter F7 to the SO input pin of shift register B8 in the Vector Data Shifters circult. causes the data bits on lines DVGO-DVG3 to be latched by B8 to lines DVX8-DVX11 when B8 is clocked by ‘the 12-MHz clock signal. LATCH3 is also the clock signal for Op Code and Intensity Latch CB. When LATCH goes low, the data bits on lines DVG4-DVG7 are latched by C6 to lines Z0-Z2, 21-22, DVX12, and DVX12.

NORM The active high-level Normalization Flag is software-generated by latch A6 in the Normalization Flag circuit. If OPO is high, NORM Is set high when STROBEO goes high. NORM is gated with SCALE by gate K5 in the Vector Timer circuit to produce the load-enable signal for Vector Timers M6, N6, P6, and Ré6. If the Vector Timers are enabled, NORM initiates the divide-by-2" operation of the vector drawing time. (The n factor is specified by the data on lines DVY8-DVY10 to Vector Scaling latch D7.)

OPTION O-OPTION 2 The Option 0, Option 1, and Option 2 signals are hardware-generated by DIP switch P10. They are applied to switch input buffer L9 of the Coin Door and Control Panel Input circuit. When L9 is enabled by SINP2, OPTION O-OPTION 2 are passed to Buffered Microprocessor Data Bus lines DB5-DB7.

OPO The Op Code 0 signal is software-generated by latch D6 in the Op Code and Intensity Latches circult. If the data on line DVG5 Is high, OPO is set high when D6 is clocked by LATCH1. OPO is multiplexed with AM4 by N3 in the State Machine circult to produce the A4 input address bit for State Machine ROM N4. If OPO is high, HALT from Halt Flag latch LS is set high when L5 Is clocked by If OPO, OP2, STROBES, and VGCK are all low, VCTR from Vector Flag latch E5 is set high when E5 is clocked by the 12-MHz clock signal.

‘OPO The Complementary Op Code 0 signal is software-generated by latch D6 in the Op Code and Intensity Latches circuit. This signal ts opposite in state to OPO. If OPO is low, NORM from Normalize tion Flag latch A6 Is set high when STROBEO clocks A6. OPO Is a the and OPX input signal for Vector Address Controller J9.

ATARI OP1 The Op Code 1 signal is software-generated by latch D6 in the Op Code and Intensity Latches circuit. If the data on line DVG6 is high, OP1 is set high when D6 is clocked by LATCH]. OP1 Is multiplexed with AMS by N3 in the State Machine circuit to produce the AS input address bit for State Machine ROM N4. In addition, OP1 is the OP1 signal for Vector Address Controller J9. In the Vector Timer circuit, OP1 Is gated by K5 and E3 to enable a1 to be loaded into the D input pin of Vector Timer P6 (if NORM or SCALE Is low).

OP The Complementary Op Code 1 signal is sofware-generated by latch D6 in the Op Code and Intensity Latches circuit. This signal Is opposite in state to OP1. OP1 is the clear signal for Vector Timers N6 and M6. When OP1 goes low, the count from N6 and M6 is stopped, causing a lowered count from the Vector Timer circuit. This low count is used to draw short vectors on the display. OP1is also gated with the outputs of the Vector Timers by gates L3 and H3 to set STOP to the low level.

OPp2 The Op Code 2 signal Is software-generated by latch D6 in the Op Code and Intensity Latches circuit. If the data on line DVG7 is high, OP2 is set high when D6 Is clocked by LATCH1. OP2 Is multiplexed with AM6 by N3 in the State Machine circult to produce the A6 input address bit for State Machine ROM N4. If OP2, OPO, STROBES, and VGCK are alll low, VCTR from Vector Flag latch E5 Is set high when ES Is clocked by the 12-MHz clock ‘signal. When STROBE1 goes low, If OP2 Is low, it is applied through gates B7 and F3 of the Vector Scaling circuit as the load signal for counter C7. This allows the data latched from DVY8-DVY10 by D7 to be loaded into counter C7. When STROBE! goes high, counter C7 counts down until It reaches the minimum count. At the same time, the Vector Timer circult does a divide-by-2 (shift right) operation for each count of C7. (This Is caused by SCALE being at the high state.) When C7 reaches its minimum count, It sets pin 12 high, dropping SCALE to the low state. If OP2 and DVYi2 are low, SCALELD from gate Jé Is set low when STROBE2 goes low This allows Vector Scaling latch D7 to latch the new data on DVYB-DVY10. If OP2 and DVY12 are low, STATCLK from J6 Is set low when

  • STROBE2 goes low This allows latch E6 of the Z Intensity and Blanking circuit to latch the data on DVY4-DVY7.

OP2 The Complementary Op Code 2 signal is software-generated by latch D6 in the Op Code and Intensity Latches circuit. This signal Is opposite in state to OP2. If OP2, STROBES, and VGCK are low, CNTR from Center Flag latch E5 Is set high when E5 is clocked by the 12-MHz clock signal. OP2 is also ORed with SA by gate R4 to produce the OP2 input for Vector Address Controller J9.

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereo! confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon. nor any right to reproduce this drawing or any part thereof, Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written licens reproduce this drawing or the subject written agreement with or written permission from the corporation.

Black Widow PCB Signal Name Descriptions

© ATARIINC., 1963 see conmmcstonsConsay SP-234 Sheet 4A

Page 8
Scan of page 8

Black Widow PCB Signal Name Descriptions, cont.

PLAYER 1 LED The Player 1 LED On signal is developed from the data bit on line DB4. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on line DB4 to pin 19 of R9. This signal is applied through R103 to light the Player 1 LED on the game Control Panel.

PLAYER 2 LED The Player 2 LED On signal is developed from the data bit on line DBS. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on DBS to pin 16 of R9. This signal Is applied through R102 to light the Player 2 LED ‘on the game Control Panel.

POR The active high-level Power-On Reset signal Is hardware-generated at pin 4 of F7 in the Power-On Reset circuit. POR Is the clock signal that starts the count of E4 of the Clock circult.

POR ‘The active lowievel Power-On Reset signal Is fe ‘ated at pin 6 of inverter F7 in the Power-On Reset circult. Is generated when the voitage at pin 3 of R8 is less than about 7 volts or when the RESET test point Is shorted to ground. POR Is developed into the RESET signal to protect Microprocessor C2.

The Random-Access Memory Enable is an active low-level signal software-generated by Address Decoder R2 during addresses 0000 through 07FF. Is the chi le signal for Random Access Memory N/P1. When low, allows data to be read from or written to N/P1, depending upon the state of WRITE.

Red Is a game PCB output signal developed from the data on

line DVY2 in the R-G-B Output circuit. When DVY2 is high and and latched to pin 3 of K10. If both BLANK and Z BLANK are low,

latch K10 is clocked by the data bit on DVY2 Is inverted

this data bit is again inverted by gate L10 to turn on Q6. Transistor Q6 generates the RED signal for the display.

RESET Reset is an active low-level signal generated at pin 6 of K3 from elther the Watchdog circuit or the Power-On Reset circult. The

Power-On Reset circuit sets RESET to an active low level either guated levels. This ensures that the Microprocessor Address Bus The Watchdog circuit sets FESET to an active low level if the

when the RESET test point Is shorted to ground or during the time that the power-supply voltages are reaching their stabilized, re-

Is stabilized before the microprocessor begins operation.

microprocessor falls to output address 0D00 before Watchdog counter H4 has reached Its maximum count. RESET Is also the clear signal for latch R9 in the Coin Door and Control Panel Output circuit.

In addition, RESET is gated with VGRST by gate L6 In the Halt

Flag circult to produce

ROM The Read-Only Memory Enable Is an active high-level signal software-generated from Address Decoder R1 during addresses 9000 through 9FFF. ROM is ORed with 1/05 by gate Ré4 to enable bidirectional data bus buffer F2 to pass data.

2” addition, ROM Is ANDed with DIS DAT to enable data buffer

ROMO Read-Only Memory Chip Select 0 is an active low-level signal

software-generatedbyAddressDecoderRiataddresses

9000-9FFF. ROMO Is the chip-select signal for ROM D1 of the Read-Only Memory circult. When low, allows ROM D1 to be addressed and to pass data to buffer E2.

ROM1 Read-Only Memory Chip Select 1 Is an active low-level signal

software-generatedbyAddressDecoderR1ataddresses

‘A000-AFFF. ROM1 is the chip-select signal for ROM E/F1 of the Read-Only Memory circuit. When low, 1 allows ROM E/F1 to be addressed and to pass data to buffer E2. ROM2 Read-Only Memory Chip Select 2 Is an active low-level signal

jeneratedbyAddressDecoderR1ataddresses

B000-BFFF. ROM2 Is the chip-select signal for ROM H1 of the Read-Only Memory circuit. When low, allows ROM H1 to be addressed and to pass data to buffer E2. ROMS Read-Only Memory Chip Select 3 is an active low-level signal

sofbyAddressDecoderR1ataddresses

CO00-CFFF. ROMS Is the chip-select signal for ROM J1 of the Read-Only Memory circuit. When low, allows ROM J1 to be addressed and to pass data to buffer E2. ROM4 Read-Only Memory Chip Select 4 is an active low-level signal

software-generatedbyAddressDecoderR1ataddresses

0000-DFFF. ROMA Is the chip-select for ROM K/L1 of the Read-Only Memory circuit. When low, allows ROM K/L1 to be addressed and to pass data to buffer E2.

Read-Only Memory Chip Select 5 is an active low-level signal

‘software-generatedbyAddressDecoderR1ataddresses

E000-EFFF. ROMS is the chip-select signal for ROM M1 of the Read-Only Memory circuit. When low, allows ROM M1 to be addressed and to pass data to buffer E2. RWB The Buffered Read/Write Enable is generated by Micro- ‘C2, buffered by B1, and applied as the read/write enable signal for custom audio chips B3 and C/D3 of the Option Switch Input and Audio Output circuit. In the high state, Is the read ‘enable for the custom audio chips; in the low state, it is the write enable for these chips.

RWB The Buffered Read/Write Eanble Is generated at pin 2 of F3 in the Microprocessor circuit by inverting R/WB. R/WB Is ANDed with Bo2 and 3 MHz by gate K4 to produce WRITE. R/WB is the direction signal for Vector Memory Data Buffer P8 and determines the direction of data flow through P8. In the high state, R/WB allows data to pass through P8 from the data bus to the vector generator data bus; in the low state, It allows data to pass in the reverse direction.

SA The active high-leve! Signature Analysis Flag signal is hardware-generated at pin 12 of inverter J3 when test point SA at pin 13 is grounded. SA is used to place the game PCB in the mode to generate signatures for reading by a Signature Analyzer or the ATARI CAT Box. SA The active low-level Signature Analysis Flag is hardware-generated when test point SA at pin 13 of J3 is grounded. ‘SA is used to place the game PCB in the mode to generate signatures for reading by a Signature Analyzer or the ATARI CAT Box.

SACLK Signature Analysis Clock is a test point at pin 8 of gate B7 in the State Machine Clock Logic circuit. SACLK is used to apply the clock signal from the Signature Analyzer or ATARI CAT Box for the reading of game PCB signatures.

SAEN ‘Signature Analysis Enable Is a test point at pin 8 of gate M5 in the Vector Address Selector circuit. SAEN is generated by gating VRAM with the data bit on line AM10 by gates J3 and M5. SAEN Is used to enable a Signature Analyzer or the ATARI CAT Box for the reading of game PCB signatures.

‘SCALE Scale is an active high-level signal generated by gate B7 of the Vector Scaling circuit. When OP2 Is high and counter C7 Is counting down, SCALE Is set high. SCALE is ORed with NORM by gate KS of the Vector Timer circult to produce the load signal for Vector Timers M6, N6, P6, and R6. When SCALE is high, the Vector Timers perform a load operation for each count of C7 (at a 12-NHz rate). This results In a vector drawing time divided by a factor of 2°, where n equals the total counts of C7. When C7 reaches Its minimum count, SCALE Is set low. SCALE Is gated with VCTR, CNTR, DVY11-DVY12, and DVX11- DVX12 of the Normalization Fiag circuit to produce the clear signal for latch A6.

SCALELD Scale Load Is an active low-level signal software-generated by tes_N5, L3, and L6 of the Vector Generel When ETROBEZ OFe,"and DV? rel iow LD is set low SCALI is the clock signal for Vector Scaling latch D7. When. SCALELD goes high, the data on lines DVY8-DVY10 are latched to the output pins of D7.

‘SINP1 Switch Input 1 is an active low-level signal softw: by Address Decoder R2 at address 7800. SINPT Is the direction signal for bi-directional data buffer M9 of the Coin Door and Control Panel Input circuit and determines the direction of data flow through buffer MQ.

SINP2 Switch Input 2 Is an active low-level signal software-generated by Address Decoder R2 at address 8000. SINP2 is the direction signal for bidirectional data buffer L9 of the Coin Door and Control Panel Input circuit and determines the direction of data flow through buffer L9.

© ATARI INC., 1983, QA were conmuncations Company STATCLK State Clock is an active low-level signal software-generated by ates _N5, L3, and J6 of the Vector Generator circuit. When SrROBEZ, OP2, and DVY12 are all low, STATCLK is set low STATCLK is the clock for latch K10 in the R-G-B Output circuit and latch E6 in the Z Intensity and Blanking circuit. Wnen STATCLK goes high, the data bits on DVYO-DVY2 are latched by K10, and those on DVY4-DVY7 are latched by E6.

STOP Stop Is an active low-level signal generated by gate H3 of the Vector Timer circult. STOP is set low when Vector Timers N6, M6, P6,and R6 have reached their maximum count. If STOP is low, VCTR from Vector Flag latch E5 and CNTR from Center Flag latch £5 are both set low when E5/s clocked by the 12-MHz clock signal.

STROBEO Strobe 0 is an active low-level signal software-generated by State Machine decoder H7. STROBED Is the clock signal for Normalization Flag latch A6. It is also the STROBEO input for Vector Address Controller J9.

STROBE1 Strobe 1 Is an active low-level signal software-generated by State Machine decoder H7. If OP2 is low, when STROBE! goes tow, the data latched at the outputs of D7 in the Vector Scaling circult are loaded into counter C7. When STROBE1 goes high, C7 begins counting down. STROBE1 Is the STROBE1 input for Vector Address Controller

STROBE2 Strobe 2 Is an active low-level signal software-generated by State Machine decoder H7. If OP2 and DVY12 are both low, from gate J6 Is set low when STROBE2 jow If OP2 and DVY12 are both low, STATCLK Is set low when \OBE2 goes low. STROBE2 Is the STROBE2 input for Vector Address Controller

STROBES Strobe 3 Is an active low-levei_signal software-generated by State Machine decoder H7. STROBES Is the clock signal for Halt Flag latch L5 and Is the STROBES Input for Vector Address Con- ~ troller J9. If OPO, OP2, OP2, and VGCK are all low, VCTR from Vector Flag latch E5 and CNTR from Center Flag latch E5 are both set high when STROBES goes low

STO-ST2 State signals STO-ST2 are active high-level signals that are softwaregenerated by State Machine ROM N4. These signals, together with ST3, are decoded by H7 of the State Machine circult to produce LATCHO-LATCH3 and STROBEOSTROBES. ST2 Is used to coveion ‘STS and Is also the ST2 input for Vector Address Controller J9.

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the soecific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereo! confers or transfers any right in. or license to use, the subject matter of the drawing or any design or technical information shown thereon. nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufac: ture under the corporation's written license. no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation.

Black Widow PCB Signal Name Descriptions

SP-234 Sheet 4B

Page 9
Scan of page 9

Black Widow PCB Signal Name Descriptions, cont.

ST3 State signa! ST3 is an active high-level signal hardware-generated by Decoder Disable latch A7. ST3 Is opposite in state to

VGCK, and Is delayed by one pulse of the 12-MHz clock Agee it high, State Machine decoder H7 Is disabled. When ST3 is tom H7

the Q4 output from State Machine ROM N4 is low and VMEM is high. If the Q4 output from N4 Is high, ST3 Is high. When ST3 Is

decodes the data on lines STO-ST2 to produce LATCHO-LAI and STROBEO-STROBES.

VCTR, VCTR The Vector Flag signals are software-generated by Vector Flag

latch ES. If OPO, OP2, S and VGCK are low and HALT Is

high, VCTR Is set high and VCTR Is set low when E5 Is clocked by the 12-MHz clock signal. VCTR is ORed with CNTR by gate M5 to set GO high. SCALE, CNTR, DVY11-DVY12, and DVX11-DVX12 are gated with CTR to produce the clear signal for Nomalization Fiag latch A6. In the Z Intensity and Blanking circuit, VCTR Is the clock signal for latch H6 and the serial Input signal for shift register M3.

VCTR and VCTR are used by the DAC Reference and Bipolar

Current Sources circult to set the X BIP, Y BIP, X REF, and Y REF levels.

VGCK The Vector Generator clock signal Is generated at pin 18 of buffer B1 In the Microprocessor circult. VGCK Is derived from the 1.5 MHz clock signal and is applied to AND gate J5 of the State Machine Clock Logic circult. VGCK Is the basic timing signal of the ‘State Machine circuit.

vaco The Vector Generator Go signal is an active low-level signal soft-

ware-generated by Address Decoder P3 at address 8840. Is

the clear signal for latch L5 of the Halt Flag circuit. When low, sets HALT to the inactive low level.

VGRST Vector Generator Reset Is an active low-level signal software-

generated by Address Decoder P3 at address 8880. VGRST is

ORed with by gate L6 of the Halt Flag circuit to produce DISRST.

VMEM ‘The Vector Memory Select Enable is an active low-level signal sof Address Decoder R1 during addresses 2000 through SFFF. VMEM is the select-enable signal for Vector Address Selectors K8, L8, M8, and N8. When VMEM allows the Vector Address Selectors to produce VW, BUFFER, and the AMO-AM12 multiplexed address bits. VMEM Is also applied to gate KS of the State Machine Clock Logic circult where It Is used to generate ST3.

VRAM The Vector Random-Access Memory Chip Enable Is an active low-level signal software-generated by Vector Address Decoder J7 at addresses 2000-27FF. When low, VRAM enables Vector Random-Access Memory K7 to be addressed _to either receive or transmit data, depending upon the state of VW. VRAM Is also used to Lehetaag the SAEN signal from M5 of the Vector Address Selector circuit. VROMO Vector Read-Only Memory Chip Select 0 is an active low-level signal software-generated Vector Address Decoder J7 at Is the chip-select signal for ROM L7 of the Vector Read-Only Memory circuit. When low, VROMO allows Heriah ah to be addressed and to pass data to the Vector Generator us,

VROM1 Vector Read-Only Memory Chip Select 1 is an active low-level signal Software generated by Vector Address Decoder J7 at addresses 3000-3FFF. Vi 11 Is the chip-select signal for ROM MIN7 of the Vector Read-Only Memory circuit. When low, VROM1 allows ROM MIN7 to be addressed and to pass data to the Vector Generator Data Bus.

VROM2 Vector Read-Only Memory Chip Select 2 Is an active low-level signal software-generated Vector Address Decoder J7 at addresses 4000-4FFF. is the chip-select signal for ROM NIP7 of the Vector Read-Only Memory circuit. When low, VROM2 allows ROM N/P7 to be addressed and to pass data to the Vector Generator Data Bus. VROMS Vector Read-Only Memory Chip Select 3 Is an active low-level signal software-generated_by Vector Address Decoder J7 at addresses 5000-5F FF. VROMS Is the chip-select signal for ROM R7 of the Vector Read-Only Memory circuit. When low, VROM3 allows Rot Ry to be acidrosted and to pass dete to the Vector Generator jus.

Vector Write Enable Is an active low-level signal softwarefrom Vector Address Selector K8, ANDed with B62 by J6, and applied as the write-enable signal for Vector Random- Memory K7. When low, VW allows data to be written to K7; high, permits data to be read from K7. i qi Watchdog Clear is an active low-level signal software-generated Address Decoder P3 at address 8980. WOCLR Is ORed with by gate E3 to clear the count of Watchdog counter H4.

WDDIS Watchdog Disable Is a test point at pin 9 of AND pate L4in the Watchdog circuit. When Is grounded, is prevented from going to an active low level (except when the RESET test point Is grounded). WRITE ~ Write Enable is an active low-level signal generated by gate K4 of the Microprocessor circuit. WRITE is used to enable Address Decoder P3 and Random-Access Memory N/P1. WRITE is also applleato pin 11 of K8 in the Vector Address Selector circuit to develop

X BIP The X-Axis Bipolar Current is set by R99 of the DAC Reference and Bipolar Current Sources circuit. This Is the current source for pin 18 of X-axis digital-to-analog converter (DAC) A/B9 of the X-Axis Output circult. X OUT X Output Is a game PCB output signal generated by the X-Axis. Output circuit. X OUT carries the horizontal beam deflection signal for the drawing of vectors on the display.

X REF The X-Axis Voltage Reference is set by the DAC Reference and Bipolar Current Sources circuit. This is the reference voltage applied to pin 14 of X-axis digital-to-analog converter (DAC) A/B9 of the X-Axis Output circuit.

Y BIP The Y-Axts Bipolar Current is set by R98 of the DAC Reference and Bipolar Current Sources circuit. This is the current source for pin 18 of Y-axis digital-to-analog converter (DAC) F9 of the Y-Axis Output circuit.

Y OUT Y Output is a game PCB output signal generated by the Y-Axis Output circult. Y OUT carries the vertical beam deflection signal for the drawing of vectors on the display.

Y REF The Y-Axis Voltage Reference is set by the DAC Reference and Bipolar Current Sources circuit. This Is the reference voltage applied to pin 14 of Y-axis digital-to-analog converter (DAC) F9 of the Y-Axis Output circuit.

20-22, 21-22 Z Intensity signals Z0-22 and 21-22 are software-generated by latch C8 In the Op Code and Intensity Latches circuit. These signals are derived from the data on lines DVG51-DVG7 when C6 Is clocked by LATCH3. If the binary count carried by Z0-22 is not equal to 1, these signals are the input signals for latch F6 in the Z Intensity and Blanking circuit. If the binary count carried by Z0-22 is 1, Z Intensity signals 20, 21, and Z2 are ANDed by gate F5 of the

ATARI Z Intensity and Blanking circuit to produce the select signal for latch F6. This select signal causes the latched data from E6 to be applied as the input signals for latch F6.

ZOUT Z Intensity Output Is a game PCB output signal generated by the Z Intensity and Blanking circuit from either DVY4-DVY7 or Z0-Z2. The Q output signals from latch H6 are summed at the base of Q7. Transistors Q7 and Q9 buffer Z OUT before it is sent to the game display circuitry to contro! the display intensity.

3 KHZ The 3 kHz clock signai is generated at pin 6 of Clock counter F4 and is applied through switch input buffer M9 of the Coin Door and Control Pane! Input circult (when SINP1 is low). The 3 kHz clock Is read by the microprocessor on data line DB7. This frequency is the time reference for the Microprocessor C2.

12 KHZ The 12 kHz clock signal is generated at pin 4 of Clock counter F4 and Is applied to reset A4 of the High-Score Table.

3.MHZ The 3 MHz clock signal is generated at pin 2 of Clock counter F4, The 3 MHz signal is ANDed with R/WB and B@2 by gate K4 to produce WRITE. It Is also applied to AND gate J5 of the State Ma- Chine Clock Logic and to shift register M3 of the Z Intensity and Blanking circult.

6 MHZ The 6 MHz clock signal is generated at pin 3 of Clock counter F4 and Is applied to gate J5 of the State Machine Clock Logic circult.

12 MHZ The 12 MHz clock signal is generated at pin 10 of inverter F3 in the Clock circuit. This signal clocks the Vector Timer Shifters, the Vector Flag latch, and the Center Flag latch.

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specitic written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof, Except ior manufacture by vendors of Atari, inc., and nutac ture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation,

Black Widow PCB Signal Name Descriptions

© ATARI INC., 1963, JA Warner Communications Campany SP-234 Sheet 5A

Page 10
Scan of page 10

This page is a drawing, shown as the original scan.

Page 11
Scan of page 11

This page is a drawing, shown as the original scan.

Page 12
Scan of page 12

This page is a drawing, shown as the original scan.

Page 13
Scan of page 13

Option Switch Input and Audio Output

Coin Door and Control Panel Input

0B7 oes oes one ons opz

ee

aKHZ WALT INERT Y a — INVERT x ZI F]oorw vacxour os7 J2o :

J20 Laver 2 cE AYER 2. LED ere NOTICE TO ALL PERSONS RECEIVING THIS DRAWING sum PLAYER | Leo CONFIDENTIAL: Reproduction forbidden without the specific writ- COIN Aux sak 68. ten permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor posse: confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown ® thereon, nor any right to reproduce this drawing or any part thereof.

ATARI Except for manufacture by vendors of Atari, Inc., and for manufac:

ion thereof corn U] cOINR| Jcorn cwre-u.

ture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by COIN CNTR-R written agreement with or written permission from the corporation

¥

Black Widow PCB Schematic Diagram

© ATARI INC., 1983 ‘SP-234 Sheet 7A > verr00: Communications Comoany 1st printing

Page 14
Scan of page 14

Vector Read-Only Memory

+5

Vector Address Decoder

Vector Memory Data Buffer

over ovee

vee irr ves

WRITE vel ves

wen

a9

a“

foes Vector Random-Access Memory

K7 AMIg. 1 aig

aeausay
AvesAMGZac

ats a 3 i

=

04ams=

aa x2 AMI Dat Ame u Ag vw tdwe aes

AB NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific writ. aver ten permission of Atari, Inc., Sunnyvale, CA. This drawing is only nee CndtionalyTasued, and nine "aca nor possession treat Centers or ansters ny ight nor licange fo use the subject mal wee ter of the drawing or any design or technical information shown thereon, nor any fight fo reproduce rawing oan prt ere Except for manufacture by vendors of Atari, Inc., and for manutacwi {ure unde’ the corporation's wien icens, no ight grented fo reproduce this drawing or the subject matter thereof, uniess by written agreement with of written permission from the corporation.

Vector Address Selector

Black Widow PCB Schematic Diagram

© ATARI INC., 1962 vere: connate Consany SP-234 Sheet 7B

Page 15
Scan of page 15

Tarn

ovao.

pies Op Code and

ovas .

Intensity

EROR

I A

ovadpeovy4
oves=lsosover 7p

ri ovac ove ove

ovat~HevYT

ovas

pves

arent TES

owe ows ove . ovy ih

'

Tate, Tate

byes

‘a0 oves sina wes dk SY al bv 7

[aren vasa

= NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only : SGndiionaily wesued. ahd neither receipt nor possession thereat ‘SOP confers or transters any right in, or license to use, the subject mat-

  • for ol the drawing or eny design or technical information shown Leela FT ® thereon, nor any right to reproduce this drawing or any part thereof. Shad 1 Hho) Except for manufacture by vendors of Atari, Inc., and for manutac- {ure under ne corporation's writen license, no right is granted (0 ove reproduce ths drawing or the subject matter thereof, unloss by = vention agreement wilt or witien permission irom the Corporation.

owe ont

Vector Data Shifters Black Widow PCB Schematic Diagram

sawn © ATARI INC., 1983 ‘SP-234 Sheet 8A TATCHT GQ A Warne: communications Company ‘1st printing

Page 16
Scan of page 16

Analysis Flag

ore Dvyi2

ovvtt PVYIC. ovy 9 Dvv8 ovy7 Dv ve. ors ovva pvY3 pvy2 ovyt DvYS Opt

re Muz,

MALT

State Machine Clock

Go AM7

Ame-+

Ams

AM4

ope

opt

ope

ams

ame

AMI

ame

Disnst Jes NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing Is only conditionally issued, and neither receipt nor possession thereot conters or trans y right in, or license to use, the subject matter of the drawing or any design or technical information shown ® thereon, nor any right to reproduce this drawing or any part thereot. Except for manufacture by vendors of Atari, Inc., and for manufac: ture under the corporation's written license, no right Is granted to roduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation.

Black Widow PCB Schematic Diagram

ATARI INC., 1983 ‘SP.234 Sheet 8B > rare: commumestions Comosny ‘18t printing

Page 17
Scan of page 17

This page is a drawing, shown as the original scan.

Page 18
Scan of page 18

This page is a drawing, shown as the original scan.

Page 19
Scan of page 19

[— ae = Sienna amen

X-Axis Output

CENTER Ig veiazor

rire xis pane wx?

DvK 7 — owe owns xs

vx

Invent X

ver

ii ALTERNATE CIRCUITRY FOR, 12 AT

1 VERSION POSITION A/89

X wie! x rer!

DAC Reference and Bipolar Current Sources

R75 RI7a

POSITION Bid ! vee wsvl

ATARI

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specitic writ. ten permission of Atari, Inc., Sunnyvale, CA. This drawing is only Conditionally is8ued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, the sublect matter of the drawing or any design of technical information shown thereon, nor any right to repreduce this drawing or any part thereat.

Except ior manufacture by vendors of Ata, Inc. and for manufac:

ture under the corporation's written license, no right is granted to

reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation.

Black Widow PCB Schematic Diagram

© ATARI INC., 1983 + Warne: Communcatons Comoany SP.234 Sheet 10A

Page 20
Scan of page 20

CENTER: you? E10 Breiszor

Y-Axis Output

vie ovvit ovne ows pw ow? owe ows aN jo Jw | Lo [or fam foo [oo

ova vs

REF INVERTY:

ant ALTERNATE § CIRCUITRY RoR.

wwEow

ove. You

owe veer ove, “5

ps cod owe su ows LOADED hs

Adjusting X- and Y-Axis Video Potentiometers If you replace the main Gravitar PCB or the display, you may have to make the following adjustments:

  • Enter self-test and advance to diagonal crosshatch pattem (Screen 2).
  • Centering Pots: Adjust X CENTER (R189) and Y CENTER (R212) so that the crosshatch pattem is located at the middle of the screen.
  • Size Pots: Adjust XSIZE (R192) and YSIZE (R213) so that the crosshatch pattem exactly covers the whole visible screen. 4, Linearity Pots: Adjust XLIN (R187) and YLIN (R210) so that the diagonal lines are straight. Since the LIN pots change the size of the displayed picture on the screen, you may have to readjust the SIZE pots in order to get the correct adjustment.
  • Bipolar Pots: Advance to the self-test raster pattern (Screen 4). Adjust XBIP (R99) and YBIP (R98) for a 1-inch high horizontal raster In the center of the screen. Be sure the raster ends are square with the sides of the outer rectangle. 18K 254K near nail [ayaa

uriseer | postTion |

yeoR

A

ATARI

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific writ-

ten permission of Atari, inc. Sunnyvale, CA. This drawing is only thereon, nor any right to reproduce this drawing or any part thereo!

conditionally issued, and neith sssion thereof Confers or transfers any right in, tor te drawing or any design of technical intormation shown

Excont ior manutgeture by vendors of Alar te. and for manviac lure under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, uniess by written agreement with or written permission from the corporation.

Black Widow PCB Schematic Diagram

© ATARI INC., 1983 © vere: conmanetens Comoe SP-234 Sheet 10B

Page 21
Scan of page 21

33K cr23 Mv5653)

Amplifone Deflection PCB

CESeUATOR

LAST USED NOT USED

To WV SUPPLY

NOTE: WARNING

LABEL ATTACHED To DAG END Leap. Hy C15)

SPARK- GAP

CRT SOCKET [ sio1

19vsTeE22

‘SPOT KILLER

SE

TA 4] POSISTOR L__] A WARNING Components Kentified by shading have special characteristics important to safety and must be replace only with identical parts. UNLESS UTRERWISE SPECIFIED

1 ALG RESISTORS VALUES AMEE Oukes, daw, 7 2G catacrtors IN pF. Nore:

Ay courcneute Loape na EST Vamsoe oy.

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither rec sssion thereot confers or transfers any right in, or license to us ter of the drawing or any de ® thereon, nor any right to reproduce this drawing or any part thereot.

Except for manufacture by vendors of Atari, Inc., and for manufac:

ture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unl n agreement with or written permission from the corporation. ign of technical information shown

wei

Amplifone

Color X-Y Display Schematic

© ATARI INC., 1962 SP-234 Sheet 11A (visi cenesesninconson tt printing

Page 22
Scan of page 22

Amplifone Main Wiring Diagram

Amplifone High-Voltage PCB

ingoot oolLr

O RED O GREEN © BLUE

O R GND

O GN GND O BU GND OX SIG

OY SIG VIDEO B+

HTRI To CRT wre2 Socxer 7'O!

HY To cRT CAP ANODE OX GND

OY GND

O ry

w

ES

a

o

et

©

© fe) JAVO HVS AH avo Mev AT a ° z = z

zx > a Zz m wo wo 5OVAC 92d _NOILI37493G St 1S 1

CRE 7 . inaoc! To cat SockeT

wot COld(6ESLIOS FEZ!

From DAG GND vOld)| vOIL

Note: Uniess otherwise specified-
WARNING g S § TE nae wetves ere ln obuna, 2 W, 5% Components identified shading a 2. All capacitor values are in uF. hans peck charaoteriation iempentent to safety and must be ‘only

with identical parts. rs

LASTUSED | NoTUsED Rig Rit, as as VRe

FAI ut Mer cre wi NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific writ: ten permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereo! confers or transfers any right in, or license to use, the subject mat-

ter of the drawing or any design or technical information shown

® thereon, nor any right to reproduce this drawing or any part thereo!, Except for manufacture by vendors of Atari, Inc., and for manufac ture under the corporation's written license, no right 1s granted to feproduce this drawing or the subject matter thereof, unless Dy written agreement with or written permission trom the corporation. Fevsid O

Amplifone

Color X-Y Display Schematic

© ATARLINC., 1983 SP-234 Sheet 11B Qa warre Communications Company 181 printing

Page 23
Scan of page 23

SOT ER

P327 DEFLECTION PCB 62s aoa NECK P328

Re wee re aw PcB a

eesrez *

ware 20! oo T

osc ose aus: ao

tae

Rss? toon

ary

GENERAL NOTES

  • Resistance values in ohms, % watt, +5%, unless otherwise noted. K = 1,000, M = 1,000,000
  • Capacitance value of 1 or less is in microFarads, above 1 in picoFarads, unless otherwise noted.
  • *Q900 and Q906 are not in High-Voitage PCB.

4, AILD.C. voltages are = 10% measured from point

Indicated to ground, using a high-4mpedance me-

ter. Voltages are measured with no signal input

and controls are in a normal operating position.

  • Circled numbers indicate location of waveform reading.
  • ZD100-101 uses (66X0040-007) zener diode in series with (340X2331-934) 330-ohm resistor in earty production models.
  • Use a 1,000:1 probe when measuring G2 (screen) or focus voltage.

ATARI

WARNING

Components Identified by shading have special characteristics Important to safety and should be replaced only with identical types.

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING without the specific writ- CA. This drawing is only ipt nor possession thereof 130 10 use, the subject mat: ig tion shown thereon, nor any right to reproduce this drawing or any part thereof Except for manufacture by vendors of Atari. Inc., and for manufac: sense. no right is granted {0 ct _matter thereol, unless by written agreement with or written permission from the corporation.

Wells Gardner Color X-Y Display Schematic Diagram

© ATARI INC., 1983

|A warner Communications Company ‘SP-234 Sheet 12A