CATHODE RAY TOMES

Primal Rage TM-397 1st Printing Universal Kit

Primal Rage (version 2.3, Jan 1995) (Atari Games, 1994) · Kit Manual · 68 pages · 50 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

AL

ATARI

GAMES

TIME WARNER INTERACTIVE

Kit Installation Instructions

Universal conversion kit for two-player upright games

Patents are pending on several parts of the Primal Rage game:

Page 4

INTRODUCTION % PxiMat RaGe UNIVERSAL KIT

Copyright © 1994 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright — laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles, In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies forfeiting such a game. Published by: Atari Games Corporation 675 Sycamore Drive Milpitas, California 95035 Printed in the U.S.A. 12/94 Produced by the Atari Games Technical Publications Department. Writing: Alan Whitehorn Design and Editing: Andrea Dencker NOTICE RE.

NON-ATARI

PaRTsS

WARNING Use of non-Atari parts or modifications of any Atari game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-Atari parts, including cabinetry, in the game. ° Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
NOTE This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an Atari game at your location, check the following: ¢ All ground wires in the game are properly connected as shown in the game wiring diagram.
  • The power cord is properly plugged into a grounded three-wire outlet.
  • On games provided with an Electromagnetic Intetference (EMD) ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Page 5

Privat RaGe UNiversat Kit INTRODUCTION

Important Notice

If you are installing this Primal Rage kit You have a Showcase 33 into a Showcase 33 cabinet with serial no.: cabinet part no.:

PEDO100 through PED0599 -O1

PED0600 through PED0750 -02 PEDO751 or higher -03

Follow the table below and check for the parts you need (or the optional parts you would like to order).

Quantity Required for Part Number -Ol cab. -02 cab. -03 cab. Description

A053517-01111Subwoofer Harness Assembly
A053518-01111XBUS Harness Assembly
148016-001111Subwoofer Speaker
A052910-0211Main Harness Assembly
149016-0021Power Supply Assembly
A052917-011Fan Assembly
178392-0011Fan Guard
052896-01*111Attraction Film
052897-01*11Wide Control Panel Decal
052899-01*11Wide Plastic Control Panel Cover
052898-01*11Metal Control Panel
A053516-01*222Control Panel Harness Assembly

“Indicates an optional part that enbances the appearance of the converted Showcase 33 cabinet or eases installation.

To order these parts, contact your distributor or the Atari Games Customer Service office nearest you; see the inside front cover of this manual.

iii

Page 6

INTRODUCTION # PRIMAL RAGE UMveRsa Kel

TY

SUMM

The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.

WARNING Properly Ground the Game. Players may receive an electrical shock if this game is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded threewire outlet. If you have only a two-wire outlet, we recommend you hire a licensed electrician to install a three-wire grounded outlet. If the control panel is not properly grounded, players may receive an clectrical shock! After servicing any part on the control panel, check that the grounding wire is firmly secured to the inside of the control panel. After you have checked this, lock up the game AC Power Connection. Before you plug in the game, be sure that the game's power supply can accept the AC line voltage in your location. The line voltage requirements are listed in the first chapter of this manual.

Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power before removing or repairing any part of the game. If you remove or repair the video display, be very careful to avoid electrical shock. High voltages continue to exist even after power is disconnected in the display circuitry and the cathode-ray tube (CRT), Do not touch the internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing it. Do this after you disconnect it from the power source. First, attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Then momentarily touch the free end of the grounded jumper wire to the CRT anode by sliding the wire under the anode cap. Wait two minutes and do this again. Use Only Atari Parts. To maintain the safety of your Atari game, use only Atari parts when you repair it. Using non-Atari parts or modifying the game circuitry may be dangerous, and could injure you and your players. Handle the CRT With Care. If you drop the CRT and it breaks, it may implode! Shattered glass from the implosion can fly six feet or more. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage rating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION Properly Attach All Connectors. Make sure that the connectors on each printed circuit board (PCB) are properly plugged in. The connectors are keyed to fit only one way. If they do not slip on easily, do not force them. If you reverse a connector, it may damage your game and void your warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (used in the United States) must not be operated in countries with 50 Hz line power (used in Europe). If a 60 Hz machine operates on 50 Hz line power, the fluorescent line ballast transformer will overheat and cause a potential fire hazard. Check the product identification label on your machine for the line frequency required. ABOUT NOTES, CAUTIONS, AND WARNINGS In Atari publications, notes, cautions and warnings have the following meaning:
NOTE — A highlighted piece of information.
CAUTION — Equipment and/or parts can be damaged or destroyed if instructions are not followed. You will void the warranty on Atari printed-circuit boards, parts thereon, and video displays if equipment or parts are damaged or destroyed due to failure of following instructions.
WARNING — Players and/or technicians can be killed or injured if instructions are not followed.

Précautions de’Emploi Générales

Page 7

PRIMAL RAGE UNIversal Kit & INTRODUCTION

PRECAUTIONS

MPLOI GENERALES

Les précautions d'emploi ci-dessous s‘adressent a toutes les personnes susceptibles d'utiliser ou de réparer ce jet La présente notice renferme également d'autres mises en garde et avertissements spécifiques.

MISES EN GARDE Mettez le jeu 4 la terre. Les joueurs risquent de recevoir une décharge électrique si le jeu n’est pas correctement mis 4 la terre! Pour éviter les décharges électriques, assurez-vous que le jeu est correctement mis a la terre avant de le brancher. Branchez-le uniquement dans une prise tripolaire avec mise a la terre. Si vous n’avez pas de prise tripolaire, i] est recommandé de faire appel 4 un électricien breveté pour en installer une. Si la console de commande n’est pas correctement mise 4 la terre, les jousquent de recevoir une décharge électrique! Si une réparation quelconque a été faite sur la console de commande, assurez-vous que le fil de mise a la terre est solidement attaché a l'intérieur de la console. Ceci fait, verrouillez le jeu. eurs Ti

Branchement sur secteur. Avant de brancher le jeu, assurez-vous que son bloc d’alimentation est compatible avec la tension secteur locale. Les conditions d’alimentation du jeu apparaissent au premier chapitre de la présente notice. Débranchez le jeu du secteur avant toute réparation. Pour éviter les décharges électriques, débranchez le jeu du secteur avant de le démonter ou de Ie réparer. Lors de la dépose ou de la réparation de l'affichage vidéo, attention aux décharges électriques. Les hautes tensions subsistent dans les circuits et le tube 4 rayon cathodique de Vaffichage méme aprés son débranchement. Ne touchez pas aux piéces internes de l'affichage avec les mains ou des objets métalliques! Prenez soin de toujours décharger le courant haute tension accumulé dans l’écran cathodique avant de le réparer, aprés avoir débranché l'appareil du secteur. Premiérement, relicz 4 la terre l'une des extrémités d'un gros fil de connexion bien isolé de calibre 18 [gauge]. Puis, touchez momentanément I'anode de lécran cathodique avec lextrémité libre du fil de connexion mis a la terre en glissant le fil sous le chapeau de Vanode de I'Gcran. Attendez deux minutes et recommencez.

Utilisez uniquement des piéces Atari. Pour éviter | risques d'accidents. utilisez toujours des piéces Atari pour réparer le jeu. L'emploi de pieces d'autres marques ou la modification des circuits du jeu sont potentiellement dangereux pour le réparateur et pour les joueurs. Prenez soin de l’écran cathodique. Si vous faites tomber [’écran cathodique et qu'il se brise, il risque d'imploser et de projeter des débris de verre pieds ou plus! Utilisez les fusibles appropriés. Pour éviter les décharges électriques, remplacez les fusibles par ceux indiqués dans la nomenclature du jeu. Les fusibles de rechange doivent étre du méme type, de la méme tension et de la méme intensité que ceux d’origine.

ATTENTION

Attachez correctement tous les connecteurs. Assurezvous que tous les connecteurs sont bien enfichés dans les cartes circuits. Ces connecteurs sont dotés d'un détromde branchement. S‘ils s'enpeur qui évite les erreur: fichent difficilement, ne foreez pas. Si vous branchez un connecteur a l’envers, vous risquez d’endommager le jeu et den annuler la garantie. Vérifiez la fréquence de ligne du courant secteur. Les jeux vidéo fabriqués pour fonctionner 4 une fréquence de ligne de 60 Hz (fréquence utilisée en Amérique du Nord) ne doivent pas étre utilisés dans les pays dont le courant a une fréquence de 50 Hz (Europe). Si vous branchez un appareil congu pour une fréquence de 60 Hz sur un courant d'une fréquence de 50 Hz, le transformateur ballast clairage fluorescent surchauffera, ce qui présente dincendie. Vérifiez la frequence de ligne requise par votre machine; clle est indiquée sur sa plaque signalétique.

REMARQUES, AVERTISSEMENTS

ET MISES EN GARDE

Dans les publications d’Atari, les conventions, en ce qui concerne les remarques, avertissements et mises en garde, sont les suivantes: REMARQUE — Sert attirer l'attention sur un point particulier.

AVERTISSEMENT — Le non-respect des directives présente des risques d’endommagement et/ou de destruction pour le matériel et/ou les pieces. En cas d’endommagement ou de destruction du matériel ou des piéces, résultant du non-respect des directives, la garantie offerte sur les cartes circuits Atari, les pieces connexes et les affichages vidéo Atari sera annulée: MISE EN GARDE — Le non-respect des directives présente des risques de blessures ou d’accidents mortels pour les joucurs et/ou les réparateurs.

Page 8

INTRODUCTION % PxIMAL RaGe UNIVERSAL KIT

CONTENTS

1 Installation How to Use This Manual Cabinet Equipment Requirements Tools Required... aa ees Inspecting the Kit ............. Preparing the Cabinet for the Kit I Assembling the Control Panel.... Connecting the JAMMA Harness........ Installing the Primal Rage Game PCB . Installing the Bezel, Decals, Labels, and Attraction Assembly Adjusting the Volume Setting the Coin and Game Option: Maximizing Earnings Game Play.

2 Self-Test Introduction ..... eaneenanseren seseve - 2-1 Entering and Exiting the Self-Test. 2-2 Select Test Men 2 Adjust Volumi Statistics ..... . 0 23 Game Option: Coin Options. Controls Test. Sound Test RAM (Memory) Te ROM Test... Video Tests Monitor Test

vi 3 Troubleshooting and Maintenance Introduction ....... ar Maintenance Precautions. Troubleshooting Procedures Repair Procedures.

4 Parts Illustrations See the list of illustrations that follows. -

5 Schematic Diagrams See the list of illustrations that follows.

Warranty Inside back cover

Page 9

PRIMAL RAGE UNiversat Kit & INTRODUCTION

ILLUSTRATIONS

Figure 1-1

Figure 1-2

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11 Figure 2-12 Figure 2-13 Figure 2-14 Figure 2-15 Figure 2-16 Figure 2-17 Figure 2-18

Figure 4-1 Figure 4-2 Figure 4-3

Figure 4-4 Figure 4-5

Figure 5-1

Figure 5-2 Figure 5-3

Figure 5-4 Locations of Control Panel Holes to be Drilled Named Locations of Control Panel Assemblies ..

Location of Self-Test Switch ........0..... 2-2 Select Test Menu Screen. Adjust Volume Screen. Statistics Screen........ More Statistics Screen . Histograms Screen .. Game Options Screen Coin Options Screen .. Controls Test Screen... Sound Test Screen .. Memory Te: Video Tests Playfield Scrolling Screen...

Alphanumerics T t Screen... Color Test Screen... Purity Test Screen . Convergence Test Screen

Primal Rage Kit Contents .0...0....ce Board Stack Assembly... Primal Rage Game (GT) PCB Assembly... . GT24MB PCB A: sembly - JAMMA Filter PCB Assembly...

Primal Rage Game (GT) PCB Schematic Diagram... 2 GT24MB8 PCB Schematic Diagram....... 5-8 JAMMA Filter PCB Schematic Diagram... CH31_2 (CAGE Audio) ‘Board Block Diagram... Table 1-1 Table 1-2 Table 1-3

Table 2-1 Table 2-2 Table 2-3

Table 3-1 Table 3-2 Table 3-3 JAMMA Pin and Wire Connections Equipment Requirements Contents of Primal Rage Ki

Summary of All Self-Test Screens. Game Option Settings caaenat Coin Option Settings ...

General Troubleshooting. ROMs and RAMs Troubleshooting Voltage Inputs and Test Points ........... 3-5

vii

Page 10

INTRODUCTION # PxisaL Race Uxivrrsat Ki

NOTES

viii

Page 11

CHAPTER 7

Installation

How To Use THis MANUAL

HE PRIMAL RAGE” conversion kit is a

one- or two-player head-to-head fight-

ing game for upright cabinets. @ This

manual provides information for installing, test-

ing, and troubleshooting the Primal Rage™ con-

version kit. ¢ Chapter 1 describes how to install

the Primal Rage kit in your cabinet, and also de-

scribes game

play. # Chapter

2 contains self-

test procedures.

The self-test is

important in the

Primal Rage game. You can troubleshoot the PC boards, main

circuits, and controls using the screens in the

self-test. ¢ Chapter 3 provides information about

maintenance, troubleshooting and repair proce-

dures for your Primal Rage game. Chapter 4

provides information you need to order parts for

your game. @ Chapter 5 contains the schematic

diagrams for

most of the Pri-

mal Rage™

game printed-

circuit boards.

Page 12

CuapTer 1 INSTALLATION PriMtat, RAGE UNIVERSAL Ket

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.

Cabinet Equipment Requirements

WARNING For safe use, you must install this Primal Rage kit in a standard Atari Games “family” cabinet, or in any universal kit cabinet that is Underwriters Laboratories listed.

Table 1-1 lists the equipment required in the cabinet into which you are installing the Primal Rage kit.

CAUTION Do rot unplug or plug in the Primal Rage game printed-circuit board (PCB) edge connector while the power is on. You could seriously damage the PCB.

Equipment Specification

Color RGB monitor Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 3V peak-topeak positive polarity Video Display

Control Panel Metal only Speakers One or two 8Q, 10 W for mono/stereo; One 4Q, 10 W subwoofer (optional: for Showcase 33 cabinets only. See page iii.) +5 VDC or +12 VDC Coin Counter

Power Cord Three-conductor with ground

Power Supply +5 VDC + 0.25V @ 12.0 amps minimum

+12VDC @ 2.0 amp Table 1- 1 Equipment Requirements

1-2 Tools Required

© Drill with a %-inch and %s-inch drill bits

  • Phillips screwdriver
  • Flat-blade screwdriver
  • Socket wrench set and ratchet

° %-inch hex wrench

¢ Wire cutters and strippers ° Straight edge

Qty.escriptionPart No.
1JAMMA Filter PC Board Assy.A047292-01
1Product |.D. Label038158-01
1FCC Compliance Label039450-01
1FBI Warning Label042452-01
1Black Bezel for Kits049774-01

1 Ye-inch Polycarbonate Control Panel Cover 054307-01

2Side Panel Decal053652-01
1Attraction Film053403-02
1Control Panel Decal053402-02
1Instruction Label052893-01
250-inch |.D. Split Ferrite Beads141026-001
8Snap-Action Switch160044-001
2Joystick Assy.171128-003
1Attraction Shield047205-01
1Bezel Label053942-01
1Primal Rage Game PCB Assy.A053926-01
12#10 Flat Washers175014-1040

12 #10-24 Zinc Nut/Washer Assemblies — 177026-0040

12#10-24 Carriage Bolts75-5112B
1#10 Wire and Cable Ties178032-002
4Red Button Assembly178237-001
4Yellow Button Assembly178237-002
2“Quick” Indicator Plate178283-019
2“Fierce” Indicator Plate178283-021
2Inverted “Fierce” Indicator Plate178283-024
2Inverted “Start/Quick" Indicator Plate178283-026
12#10-24 x %-inch Long Carriage Bolts.75-5112B

1 Primal Rage Universal Kit Installation Instructions TM-397

Note: A JAMMA harness is not included in this kit. If your game cabinet does not already have a JAMMA harness installed in it, you can order this harness from Atari Games Customer Service. Also, packaging materials are not listed above.

Table 1-2 Contents of Primal Rage Kit

Page 13

PRIMAL RAGE UNIVERSAL Kit ¢ CHAPTER 1 — INSTALLATION

© Squeegee ¢ X-ACTO™ knife

© Insulated wire connectors (if you are installiag a new JAMMA harness)

  • Carbon paper

¢ Saber saw

° File

  • Bandsaw
  • Tape or glue

Inspecting the Kit

Check to see that you have all the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Primal Rage kit serial number, part number, and description of the missing or damaged parts, and date received.

Preparing the Cabinet for the

Kit Installation

WARNING To avoid electrical shock, unplug the cabinet while installing the kit. After installation, plug the game only into a grounded 3-wire outlet.
  • Turn off power to the game, and unplug the power cord.
  • Remove the following from the cabinet: ¢ Existing PCBs
  • Game harness, if it is not Japan Amusement Machinery Manufacturers Association (JAMMA)— compatible Control panel decals, labels, and controls Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals. Video display (monitor) shield, display bezel, attraction shield, and marquee.
  • Wipe down and vacuum the cabinet. Paint the cabinet, if required.

Assembling the Control Panel

Parts Needed for this Kit

To assemble the control panel, you must first decide where to cut the control panel holes (refer to Figure 1-1). Create a template sheet from the illustration. You will also need the following parts from the kit: ¢ Clear control panel cover ¢ Control panel decal © Red and yellow button assemblies

  • Snap-action switches
  • Indicator plates: Fierce, Start, Quick, etc. ¢ Twelve #10 flat washers, #10-24 x ¥-inch-long black carriage bolts, and #10-24 nut/washer assemblies © Joystick assemblies

Installing the Parts

  • Using carbon paper, transfer the design from the template to the control panel. Save the template. 2, Using a saber saw, carefully cut out the two large holes for the joystick assemblies. Deburr the sharp edges with a file.
  • Drill the eight 1.187-inch holes for the buttons.
  • Lay the plexiglass cover over the top of the control panel and mark the outside shape of the panel on the plastic. Also mark the button holes as close as possible to the locations shown on the template. we Lastly. mark the positions of the four holes that will be used for securing the cover to the control panel. These four holes can be placed anywhere near the corners — wherever space permits.
  • Using a bandsaw, cut the control panel cover to its correct outside shape.
WARNING Wear safety glasses when drilling the plastic contro! panel cover. Use care to avoid shattering or chipping the plastic.
  • Tape or glue the template to the plexiglass cover. To start the saber saw cuts, drill a 4-inch hole inside the hole for the joystick, and the button holes.

1-3

Page 14

Caper 1 INSTALLATION & Primal Rack UNIVERSAL KIT

ignal Instructions

Component Side

1POWER GNDConnect to the 5V RTN terminal on the

power supply. However, if you have 12V. RTN, connect one of the wires at pin 1, 2, A, or B to the 12V RTN terminal.

2 =POWER GNDSame as pin 1
3+5VDCConnect to the +5V terminal on the power

supply.

4+5V0CConnect to the +5V terminal on the power

supply. However, if your power supply has a + Sense terminal, connect to the + Sense 5 -5V

6+12VDCConnect to the +12V terminal of the power

supply. If your coin counter(s) require 12V, also connect to the + side of the coin counter(s). 7 Key

8COINCTR1Connect this wire to one side of the left

12V coin counter. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate 9 Notused

10SPKR+LConnect to the + terminal on the left

speaker.

41SPKR+RConnect to the + terminal on the right

speaker.

12REDAttach to the video display.
13BLUEAttach to the video display.
14VIDEOGNDAttach to the video display.
15SELF-TESTUse this wire if you want an external self-

test switch. However, the kit already has a self-test switch on the PCB. (/f you connect an external self-test switch, switch off the switch on the PCB. Connect the wire to the N.O. terminal on the external self-test switch. Connect the common terminal of the switch to a GND wire.)

16LTCOINConnect to the N.O. terminal of the left

coin switch. Connect the common terminal of the switch to a ground wire. 17 START1/QUICKHIGH Connect to the N.O, terminal of the switch.

18UPIConnect to the N.O. terminal of the switch.
19DOWNConnect to the N.O. terminal of the switch.

20 = LEFTI Connect to the N.O. terminal of the switch.

24°RIGHT1Connect to the N.O. terminal of the switch.

22 FIERCEHIGH — Connect to the N.O. terminal of the switch.

23QUICK/LOWConnect to the N.O. terminal of the switch
24=FIERCE/LOWConnect to the N.O. terminal of the switch

25 = Notused 26 Notused

27GNDConnect to the common terminal of the

switches

28GNDConnect to the common terminal of the:

switches. Signal Instructions

A

ez mm 0 OG

@a2o0oT7ON<KMECKC aAgVQRDVZ FSF TK RTN

RTN +5VDC

+5V DC

-§V DC. +12VDC

Key COIN CTR2

Not used SPKR -L.

SPKR-R

VIDEO GREEN COMPSYNC Not used Not used RT COIN Solder Side Connect to the 5V RTN terminal on the power supply, However, if you have 12V RIN, connect one of the wires at pin 1, 2, A, or B to the 12V RTN terminal. Same as pin A. Connect the +5V terminal on the power supply. Connect the +5V terminal on the power supply,

Connect to the +12V terminal of the power supply.

Connect this wire to one side of the right 42V coin counter. Clip R18 on the game PCB if you use a second coin counter.

Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate.

Connect to the ~ terminal on the left speaker. Connect to the - terminal on the right speaker. Attach to the video display. Attach to the video display.

Connect to the N.O. terminal of the right coin switch. Connect the common terminal of the switch toa GND wire. START2/QUICK HIGH Connect to the N.O. terminal of the switch. UP2 DOWN2 LEFT2 RIGHT2 FIERCE HIGH QUICK/LOW FIERCE LOW Not used Not used GND

GND Connect to the N.O. terminal of the switch. Connect to the N.O. terminal of the switch. Connect to the N.O. terminal of the switch. Connect to the N.O. terminal of the switch. Connect to the N.O. terminal of the switch. Connect to the N.O. terminal of the switch. Connect to the N.O. terminal of the switch

Connect to the common terminal of the switches, Connect to the common terminal of the switches.

Table 1-3 JAMMA Pin and Wire Connections

Page 15

Prima RAGE UNIveRsaL Kit ¢ CHAPTER 1 — INSTALLATION

NOTE The four holes in the corners for securing the contro! panel cover are not shownin this illustration. Drill these holes wherever space permits.

Suggested distance from the front of the control panel. Check that the controls have | | sufficient clearance before cutting any holes| “1.75 DIA DETAIL A 2x _. SEE DETAIL'A’ 1.187 2x _ / 8x

o / oO / a

9.11 / ra, 4 o OG CHES I | oN a, patted 1.31 + i SEE ' 00 v / a a | . . T 4.75 | I 7.94 3.06 6.50 —] 8.00 —}

23.63

Figure 1-1 Locatlons of Control Panel Holes to be Drilled

  • Saw out the large holes for the joysticks and the button holes.
  • Drill the four %-inch holes that will be used to mount the cover to the control panel and the eight 0.205inch bolt holes to mount the joysticks 10. the plexiglass cover.
  • Install the control panel decal on the control panel Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes for the controls.
  • Install the cover on the control panel using the four %-inch-long carriage bolts, washers, and nut/washer assemblies.

w . Install the joysticks using the the %-inch-long carriage bolts, washers, and nut/washer assemblies. To prevent injury, carefully deburr all the edges of *

  • Install the button assemblies with their indicator plates and snap-action switches (refer to Figure 1-2 for correct placement) For maintenance and servicing information on the controls, refer to Chapters 2 and 3 of this manual.
Page 16

CHAPTER 1 ~ INSTALLATION & PRIMAL RaGE Uxtversal. KIT

Quick Fierce igh High

Quick Fierce Low Low Player 1 Quick Fierce High High

Quick Fierce Low Low Player 2

Figure 1-2 Named Locations of Control Panel Assembiles

Connecting the JAMMA

Harness

  • If your game cabinet does not already have a JAM- MA harness, install a JAMMA harness in the cabinet. To purchase a JAMMA harness, contact the Atari Games Customer Service office closest to you.
  • Install the pair of split beads on the harness as close to the PCB edge connector as possible. Hold the beads on the harness with the tie wraps included in the kit.
CAUTION You must install the split beads and the JAMMA Filter PCB on the JAMMA harness to meet FCC requirements. (These parts are included in the kit.)
  • Using Table 1-3 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering,
WARNING Do not simply tie the wires together. If you do, you could cause intermittent problems, loose connections, oxidation, or a fire.

Connecting Power Wires

  • Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Primal Rage kit requires +5V and +12V. The -5V is not needed and should not be used. Tie off any

1-6 other voltage wires on the power supply besides +5V, and +12V. There is more than one wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that the power wiring does not overload and burn.

Connecting Video Dispiay Wires

NOTE The JAMMA harness provides only negative composite sync.

Connect the wires designated for the red, green and blue video guns along with the sync and ground wires, according to Table 1-3.

Connecting Coin Door Wires

  • Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.
  • Connect one terminal of the door lamps to one of the BK/W wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
NOTE Do not use -5V for the coin door lamps.

Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.

Page 17

PRIMAL RAGE UNIVERSAL Kir CHAPTER 1 — INSTALLATION

Connecting the Control Wires Connect the joystick and button harnesses to the JAM- MA harness using crimp splices or butt soldering, according to the information in Table 1-3.

Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the foot pedal, the video display, and the power supply. This AC ground must be of #18 AWG wire or larger.

WARNING For the safety of players, you must connect the green ground wire as indicated above.

Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; and +12 Volts on pins F and 6. Check that the video display and the attraction lamp have power. Now turn off the power to the game.

Installing the Primal Rage

Game PCB

1, After you have checked the power on the JAMMA. connector (described above), install the Primal Rage game board in the cabinet. Use the four screws and standoffs supplied with the game board to mount it onto the wooden cabinet surface.

  • Connect the JAMMA harness connector to the Filter PCB.
  • Secure the JAMMA harness away from the PCB with cable ties.
  • Turn on the power to the game. Check that the game PCB functions. If a video picture is not present, see Chapter 3.

Installing the Bezel, Decals,

Labels, and Attraction

Assembly

Installing the Display Bezel Find the cardboard display bezel in the kit. This bezel can accommodate both 19-inch and 25-inch video displays. Follow the instructions on the back of the bezel, and cut the hole and outside edges as required. Then find the game instructions label in the kit, and adhere that label to the bottom center of the bezel.

Installing the Product ID and FCC Label Place the product ID label (part no. 0938158-01) and FCC compliance label (part no. 039450-01) on the back of the cabinet.

Installing the Side Panel Decals Find the side panel decals in the kit. Wet the left and right side panels of the cabinet with slightly soapy water. Then position the decals on the side panels of the cabinet. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.

Installing the Attractlon Assembly Find the Primal Rage attraction film in the kit (the attraction shield may be reused from your cabinet). Using the existing shield as a template, cut the film to size, if necessary. Install them in the cabinet attraction assembly.

Adjusting the Volume

There is no volume adjustment knob on any PCB in this game. Instead, volume is adjusted in the self-test software. The attract-mode and game-play volumes can be adjusted separately. Refer to Chapter 2 of this manual for more information.

Setting the Coin and Game Options

Set the coin and game options in the self-test. See Chapter 2 for information about the option settings.

Maximizing Earnings

For maximum earnings, regularly maintain your Primal Rage game. When you set up the game and when you collect money, use all the screens in the self-test procedure — especially the Control Test.

Page 18

Cnaprer 1— INSTALLATION Prisal RaGe Universat Kiv

Game Play

This section describes the features and play of the Primal Rage game.

Introduction

Primal Rage is a head-to-head fighting game featuring state-of-the-art stop-motion animated characters, Players choose from seven different giant fantasy creatures in an attempt to dominate the new “Urth,” using fighting moves, powerful “secret” moves, masterful combo hits. and graphic finishing sequences to eliminate their opponent. Primal Rage utilizes a proprietary new stop-motion animation technique that provides realistic and life-like character motion. In addition to state-of-the-art graphics, Primal Rage features the new CAGE “Total Immersion Audio” system, providing great stereo sound that punctuates high-impact game play. Due to their great size and special powers, each of the seven available characters in Primal Rage is worshiped as a “god” by the surviving humans of Urth. As players go through the game, they amass additional followers with every victory. Followers can also be eaten to replenish strength, if needed, but this is really a matter of personal taste. Primal Rage features a four-button control that allows “power” hits to be mapped onto both the top and bottom button pairs. To execute special moves, Total Immersion Audio players must press and hold button combinations while moving the joystick at the same time, in a method that differs from standard fighting game controls. This allows for a diversity of regular hits while at the same time providing a new way of executing special moves. Because of this feature, Primal Rage controls allow for very fluid combination potential. Advanced players will be motivated to learn all of the moves to develop the best combinations, providing the driving force for high-level competitive action,

The game offers two basic types of play:

  • One-player game. The player must defeat all seven opposing characters to get to the Bonus Round and Final Bartle, ¢ Two-player game. Players battle each other for trophies, human followers, and World Domination. The winner is the player who captures the most “globes” and amasses the most followers.

One-Player Game

The player must defeat all seven opposing characters, one at a time, in order to get to the Bonus Round and Final Battle. Each player and opponent character has a “health bar” at the top of the screen that is reduced whenever a damaging hit is made. If a player’s health bar is reduced, human followers can be eaten for bonus health. Each opponent defeated will result in a new territory being awarded.

Finishing Moves When an opponent character has lost all its health and is standing there dizzy, the character is in its “death throes” and is about to die. The “finishing move” is a special button combination (different with each character) that can be used to “finish off" an opponent while it is in its death throes. Using a finishing move demonstrates technique and generates excitement, but, most importantly, affects the status of opponent characters when they return during the Final Battle. Players will be motivated to master all of the finishing moves in order to play a perfect game. Bonus Round and Final Battle

After defeating all seven opponents, the player is awarded a Bonus Round, during which points and bonus health can be collected by snacking on human. followers. After the Bonus Round, the player moves to the Final Battle, during which all of the player's foes must be quickly vanquished once again, only this time with a twist: the player has only one health bar plus bonus health, and each opponent character will return either as a normal character or as a ghost-like character. Any character that the player did not eliminate using a finishing move during the regular rounds will come back as a normally healthy character. Characters on which a player successfully executed finishing moves will return as ghosts that suffer more damage per hit inflicted. Any player who has won the Final Battle is rewarded with the story line for that character and a special graphic picture depicting that character's life after they he | ¢ 10 los have captured Urth, Players

Page 19

PRIMAL Race Unive AL Kir % Carter 1 — INSTALLATION

during the Final Battle have the opportunity to continue the game by adding more coins Challenge Game During a 1-player game, another player can challenge the current player by inserting coins in the unused side of the game. The original player now competes against the new challenger.

Two-Player Game

Players battle each other in a match decided by winning two out of three rounds. A trophy and human followers are awarded to the player who wins each round, and a new territory on the globe is awarded to the winner of the match.

Human Followers Human followers are awarded for various accomplishments in the game. The number of followers awarded depends upon how well a player fights, including attack combinations, damage to the opponent, use of finishing moves, and fatalities.

Sudden Death If the two players are tied at the end of the third round (same number of trophies and both players still alive), then a Sudden Death round is started. At the beginning of Sudden Death, the timer is reset to 20 and players receive full health bars. During play, each player's health bar will be reduced by time and hits. If Sudden Death ends without a victor, both players will die and the game will end in a tie. World Domination In order to achieve World Domination, a player must win all seven territories on the globe. When this is achieved, the player will be awarded a globe and more human followers. There is no limit to the number of globes awarded in a 2-player game. The winner is the player who captures the most globes and amasses the most human followers.

Hidden Features

Many hidden features are included in Primal Rage. Some of these features are activated by different joystick and button combinations. Some are skill-specific and some require cooperation between players. Many hidden features depend upon which character is being played, which background is in view, or which combination of moves is used.

Page 20

Cuaprer 1 — TALLATION % PruMaL RaGr UNIVERSAL KIT

1-10

Page 21

CHAPTER 2

Self-Test

Int

my. HIS CHAPTER contains a description

of the self-test for your Primal Rage™

& game. Use the self-test to check the

condition of the game circuitry and controls.

You will see the self-test informa-

tion on the video display and

hear the sound test information

through the speakers. You do not

need any additional equipment to UCTION

perform the self-test. Perform the self-test

when you first set up the game, each time you

collect the money, or when you suspect game

problems. This chapter shows the screens in

the self-test and explains each of the tests. The

screens and explanations are arranged in

the order they appear in the self-test.

Table 2-1 lists all the self-

test screens.

Page 22

Chapter 2 - SELF-Test @ Pwiviar Race UNiveRsaL Kit

SelfTest Switch

Figure 2-1 Location of Self-Test Switch

Entering and Exiting the

Self-Test

The game’s self-test switch is located on the Game PCB (see Figure 2-1), Also, in Table 1-3, refer to the instructions regarding Pin 15 if you want to install an external self-test switch. Turning on this switch causes the screen to enter the self-test mode. Doing so displays the Select Test menu; see Figure 2-2. Exit the self-test by turning off the self-test switch at any time. At the bottom of the self-test screen you may find that the MOS or OS versions shown in this manual are different from your game. Any version differences in the software are unimportant.

Select Test Menu

Choose which test or screen you want to see from this menu, shown in Figure 2-2. Move up and down the menu by moving either joystick up or down (or by pressing the left player upper right button). Start the selected test by pressing the left player upper left button. AbsVET VOLUME Eh iia conrnois rest

wipes TeSYS wOMRTOR TESTS

Figure 2-2 Select Test Menu Screen

Adjust Volume

Adjust the volume of the game using this screen, shown in Figure 2-3. Follow the instructions at the bottom of the screen to restore the old volume level or to save the new volume and return to the select test menu.

Page 23

PRIMAL RAGE UNIVERSAL Kit 4 Cyaprer 2 — SELF-TEST

Select Test Menu

Adjust Volume

Statistics

More Statistics Histograms

Game Options

Coin Options

Controls Test

Sound Test

RAM (Memory) Tests Video RAM Video RAM (quick) Color RAM Working RAM Working RAM (quick) AllRAM

ROM Test

Video Tests Playfield Scrolling MOB (Moving Objects) Checksums Alphanumerics

Monitor Tests Color Test Purity Test Convergence Test

Table 2-1 Summary of Ail Self-Test Screens

fc “AOaVST VORUAG ‘

{UG 7

vo R33 N9" SE Rie POE te Mb ke b. S7SE ETERS” vee Eos bY ETES Th "ETT

Figure 2-3 Adjust Volume Screen The software continuously plays music to allow you to adjust both the game and attract-mode volume levels. The word GAME or ATTRACT flashes to show which of the two volumes levels you are adjusting. Move either joystick up or down to select either one. The attractmode volume level has four steps: mute, 1/3, 2/3 or full

volume level (these are fractions of the game volume

level).

Use the information shown in the statistics and histogram (bar graph) screens to keep track of your game use and maximize your profits. The game statistics are collected from the last time the statistics were cleared. Follow the instructions at the bottom of the screen to clear the statistics or to advance to the next statistics or histogram screen.

Statistics Screen

The Statistics screen (see Figure 2-4) lists the following information:

  • Left Coins shows the number of coins counted in the left coin mechanism.
  • Right Coins shows the number of coins counted in the right coin mechanism.
  • Aux Coins shows the number of coins manually added by the operator. (not inserted into any mechanism).
  • Idle Minutes shows the number of minutes that the game was idle and not being played.
  • 1-Player Minutes/2-Player Minutes shows the number of minutes that the game was played by one or two players.
  • New Game Minutes shows the number of minutes played after starting a new game.
  • Continued Game Minutes shows the number of minutes played after continuing a game.
  • EEPROM Error Count shows the number of errors. counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEPROM at 22H on the Primal Rage game PCB.
Page 24

Cuaprer 2 —Sece-Test Prat Racr UNiversal KIT

meee LEFT Pe YES BEgHT Burren vanes UEP] VEER rege ourres

Figure 2-4 Statistics Screen Average New/Continued 1 Player Time shows an average of the number of minutes played by one player in a new or continued game. Average 1 Player/2 Player Game Time shows an average of the number of minutes played in one game by one or two players. Total Coins shows the number of coins counted in both left and right coin mechanisms. Average Time per Coin shows an average of the number of minutes played for every coin counted. Percentage Play shows the ratio of game playing time to total time the game has been turned on.

More Statistics Screen

The More Statistics screen (see Figure 2-5) lists the following information: © 1 Player/2 Player Games shows the number of games played by 1 or 2 players. «¢ 1 Player/2 Player Continues shows the number of games continued by 1 or 2 players.

  • 1 Player Finishes shows the number of games finished in 1-player game mode.
  • Challenge Games shows the number of 1-player games interrupted by a 2nd-player challenge. ¢ Sudden Deaths shows the number of tie games decided by sudden death. ¢ Final Battles shows the number of times a single player achieved a Final Battle. ¢ Final Continues shows the number of credits used during a Final Battle. Figure 2-5 More Statistics Screen

Histogram Screens The Histograms screen is a menu that lets you display one of three screens (see Figure 2-6). These show v: ous horizontal bar graphs for round time, match time, and selections per character.

OUND YIME GIN SECONDS?’ ly

TeTALseey = MEDIADT 2a BD Peers BET EbeA PERE SOTTO adh

Figure 2-6 Histograms Screen

Game Options

Check and select the game options on this screen, shown in Figure 2-7. The screen shows the factory default settings in green.

To move through the options, to change or save the settings, or to return to the select test menu, follow the instructions shown at the bottom of the screen. The game options, with defaults, are shown and explained in Table 2-2

Page 25

PRIMAL RAGE UNIVERSAL Kit & CHapTer 2 — SeLr-Test

Game Option Available Settings Explanation

Game DifficultyEasiestMedium ¥Provides a choice of 16 levels of game

Most Difficult difficulty.

Game GoreNo GoreFull Gore ¥Provides a choice of two levels of gory effects. No

Gore disables all blood and finishing moves.

Censor StrictnessEasygoingStrict ¥Strict setting disallows certain vulgar letter

combinations in the high score table and in the top score display.

Demo ModeYesNowIn demo mode, characters never die. This setting

should be used for demonstrations only.

Restore Factory Coin DefaultYesNowReturns coin settings to factory default.
Auto Reset High Score TableYesvNo.Automatically clears the high score table

periodically.

Reset High Score TableYesNowClears the high score table the next time you start a

game (one time only).

Restore Factory DefaultYesNowReturns all game settings to factory default.

v Manufacturers recommended settings Table 2-2 Game Option Settings

Coin Option Available Settings

Free Play Now Yes Explanation

Lets you choose free play to demonstrate the game. Discount to Continue Now Yes When setto Yes, this option reduces by 50% the player's cost to continue a game (always rounded up to the next full coin) 1 coin 1 credit 2 coins 1 credit vw 3coins 1 credit Game Cost

B coins 1 credit The number of coins required for one credit.

Bonus for Quantity Nonew Buy-in 2 coins give 1 3coins give 1 3coins give 2

9 coins give 2 coins give 3 Lets you choose from various kinds of bonuses or no bonus.

1 coin counts as 1 coin” 1 coin counts as 2 coins Right Mech Value

1 coin counts as 7 coins 1 coin counts as 8 coins The number of coins each coin counts as in the right coin mechanism.

1 coin counts as 1 coin¥ 1 coin counts as 2 coins Left Mech Value

1 coin counts as 7 coins 1 coin counts as 8 coins The number of coins each coin counts as in the left coin mechanism.

v Manufacturer's recommended settings

Table 2-3 Coin Option Settings

Page 26

Cuaprer 2 - See-Trst @ Prima RaGr UNIVERSAL KI

vector’ coin SErauLT? ayyy MESSY NIGH scome vasisy agye? MEOH scene TasLE? o mom © ental tae A

Figure 2-7 Game Options Screen wires tren

Coin Options

Check and select the coin options on this screen, shown in Figure 2-8. The screen shows the factory default settings in green. To move through the options, to change or save the settings, or to return to the select test menu, follow the instructions shown at the bottom of the screen. The coin option settings, with defaults, are shown and explained in Table 2-3.

pge PLave ej goount Te caevy ious bee Me Sys Tee Guaarrery Guvesmt he To et a ee

ana a

Figure 2-8 Coin Options Screen

Controls Test

The controls test screen is shown in Figure 2-9. This test checks all the pushbutton switches and the joystick potentiometers. mma Ad 200. Bale Sa HEE

+f

rag x i

\ whEET ESET CREE GAH «

Figure 2-9 Controls Test Screen As you use each control, the numbers for the joystick pots increase or decrease, or the red Xs for switches become Os. If the changes do not appear on the screen, check the controls and their wiring. To reset the joystick pot limits, to change or save the settings, or to return to the select test menu, follow the instructions shown at the bottom of the screen. Press and old the left player upper right button to exit from the controls test.

Sound Test

Use this selection screen, shown in Figure 2-10, to test the sound board.

NOTE The audio boards must be installed and connected in the game to perform this test.

To check the audio ROMs, run the Audio Checksums test. To determine if all three speakers are working properly, select the Speaker Test. In the Audio Checksumss test, verify that all the checksums are displayed in white. If any of them show red numbers, you have a problem with the circuitry or ROMs. If all ROMs are bad, suspect the circuitry. If a single checksum is bad, check for improper ROM seating.

Page 27

PuiMaL Race UNIVERSAL Ki? CHAPTER 2 — SELE-TEST

ONO Ve6Tt——")

ANDIO CHEEK SUES SPEAKER TEST

reass LET EbURETRS AR SOT

Figure 2-10 Sound Test Screen When you select the Speaker Test, you will hear a sequence of three sounds, with a different sound coming from each speaker: the left speaker will emit a frog sound, the right speaker will emit a woman's scream, and the sub-woofer will emit a booming footfall sound.

NOTE The footfall sound coming from the subwoofer will also be heard to a certain extent from the other two speakers.

RAM (Memory) Tests

Use this selection screen, shown in Figure 2-11, to run any of the five RAM tests. These tests check the RAM chips in various ways. When you turn on the power, the game automatically runs through the random-access memory (RAM) tests. Refer to Chapter 3 of this manual for more details.

TIMES BEY cousexs omen RA antes man wermine 2am CEUteR> ALL mam

eres URE EbebEST Re TABS DUTT

Figure 2-11 Memory Tests Screen

ROM Test

This screen displays any ROM errors by showing a nonzero Pumber after a particular item. A properly working board should cause your screen to display only Os in the right column. if a ROM fails, a message may be displayed. However, depending on how bad the ROM error is, you may not be able to enter the self-test.

If you have a ROM error, check the four ROMs ijabeled PGM_LL. PGM_LM, PGM_UM, and PGM_UU at 24L through 29L on the Primal Rage game PCB. Check these locations for bent pins or incorrectly inserted chips. Also see Table 3-2 for information about the locations of the ROMs and their functions.

Video Tests

Use this selection screen, shown in Figure 2-12, to determine the condition of the video circuitry on the game PCB.

PLAvRIELD SoBe FT eae CAREER SRT eh eR AEB

Figure 2-12 Video Tests Screen

Playfield Scrolling The playfield scrolling test is shown in Figure 2-13. To scroll the playfield continuously in a horizontal or vertical direction, move the joystick in the corresponding direction. Make sure that the playfield screen is clean and scrolls smoothly across the screen. if the screen image does not move, or appears different from Figure 2-14, you have a problem in the playfield circuitry at locations 25N-28N on the Primal Rage game PCB. To return to the select test menu, follow the instructions shown at the bottom of the screen.

y

Page 28

Cuaprer 2 —SeLr-Test & Prival Race Universal KIT

Figure 2-13 Playfield Scrolling Screen

MOB (Moving Objects) Checksums The first MOB test screen examines the checksums of the MOB ROMs. If the checksums match, you should see the white numbers displayed as shown in Figure 2-

  • The twelve designations listed in the left column on the screen (MOHO/MOLO through 1.3) are the labels on the chips, located on the Primal Rage PCB and the GT24MB8 piggyback board. If the checksums do not match, either you have a defective EPROM/ROM or a chip may be installed incorrectly.

verse (SED CL HEE RMAs SuTree

Figure 2-14 MOB Checksums Screen

Alphanumerics The alphanumerics test is shown in Figure 2-15, To page (scroll) the screen up/down, move the joystick accordingly. If the screen image does not move, or appears different from this figure, you have a problem in the alphanumeric circuitry at location 22P/R on the Primal Rage game PCB, To return to the select test menu, follow the instructions shown at the bottom of the screen. Figure 2-15 Alphanumerics Test Screen

Monitor Tests

The monitor test selection screen lets you select from three screens — color, purity, and convergence. Advance to each screen to completely test the monitor.

Color Test

The color test (see Figure 2-16) indicates the dynamic range of the video display color circuitry. The screen should show three bands (red, green, and blue) in the left half, plus white in the right half, ranging from black to white, from left to right. The red, green, and blue bands are produced by only one color gun being turned on in each band.

Figure 2-16 Color Test Screen

Purity Test The next five screens are color purity tests. The entire screen will be red (see Figure 2-17), green, blue, white, and grey. Press the left player upper left button to

Page 29

Print Race UNIVERSAL Kir @ CHaprer 2 — SELr-Test

change colors. Each screen should show no unevenness of color and no lines in the display.

Figure 2-17 Purity Test Screen

Convergence Test The convergence test has three screens — white, violet, and green backgrounds with grid lines. This sequence is then repeated but without any text on the screen. The green screen is shown in Figure 2-18. To see the remaining screens or return to the select test menu, follow the instructions shown at the bottom of the screen. atanomenets

Figure 2-18 Convergence Test Screen Check the following on the screens: ¢ The grid lines should be straight within 3.0 mm and the lines should not pincushion or barrel.

  • The convergence of the lines on the violet and green screens should be within 2.0 mm. If these screens do not meet these criteria, adjust the video display as described in the video display manual. Return to the select test menu by pressing the thumb button.

Causes of errors could be problems with the cable, terminators installed incorrectly, harnesses, or connectors,

2-9

Page 30

Cuaprer 2 - SELF-Test % Pximal RaGE UNIVE

Page 31

CHAPTER 3

Troubleshooting

and Maintenance

INTRODUCTION

HIS CHAPTER provides information

about maintenance, troubleshooting

and repair procedures for your Primal

Rage™ game. The maintenance section gives

information on cleaning the parts. The trouble-

shooting section contains several tables to help

determine the source of a problem and the steps necessary to repair it. The repair section

contains the steps necessary

to remove and install the ser-

viceable parts. Together, these

three sections provide a com-

plete guide to servicing your

Primal Rage™ game.

Page 32

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE “PRIMAL RAGE UNIVERSAL KIT

Maintenance Precautions

Introduction This section describes the precautions that you should be aware of when performing maintenance procedures on the game. Maintenance procedures should be performed every 34 months on a regular basis.

WARNING Before performing any maintenance or repairs, please observe all of the following safety precautions:
  • Turn the game's power off.
  • Unplug the power cord from the electrical socket.
  • Secure loose clothing such as ties and long sleeves that could get caught within the game.
  • Remove all metal jewelry such as watches and necklaces that could conduct electricity from the game's power sources.

Troubleshooting Procedures

This section is designed to help determine the source of a malfunction and contains detailed information on repairing the problem. Table 3-1 General Troubleshooting, is divided into two columns. The left-hand column is broken down into the general nature of problems. The right-hand column. lists suggested solutions to solve the problem. Table 3-2 ROMs and RAMs Troubleshooting, is designed to help determine the specific ROMs and RAMs that are the source of a game logic malfunction. The left-hand column shows some problems that may result from malfunctioning ROMs and RAMs. The middle column shows the ROMs and RAMs that may be the source of the problem and their purposes. The right-hand column shows the PCB locations of the ROMs and RAMs that may be causing the problem. Table 3-3 Voltage Inputs and Test Points, is divided into three columns. The left-hand column shows the correct voltages that should be measured. The middle column shows the physical locations of the test points or LEDs. The right-hand = column shows the sources and purposes of the voltages.

Repair Procedures

Introduction This section describes the repair procedures for all of the major assemblies and components of the game. Before performing any repairs, use the tables in the Troubleshooting Procedures section to help narrow the source of the problem,

Speakers The game is designed to use three speakers: two top speakers under the attract panel and a sub-woofer next to the coin door. The speakers provide the music and sounds for the game and self-tests. Failure of the speakers may result in distorted or no sound. If this is the case, replace the speakers by following the removal and installation steps below.

  • Remove the screws securing the speaker grille; remove the speaker grille and set it aside. Remove the speaker mounting screws. Disconnect the harness from the speaker.
  • Replace and reinstall the speaker in reverse order.

ot Joysticks If you want to repair the joystick control, you musi disassemble it by removing it from the control panel.

System Logic Assemblies This section describes the repair and maintenance procedures for the major assemblies and components that are related to the system's logic and electronics, including the printed-circuit boards (PCBs) and the power supply.

Primal Rage Game PCB Set The Primal Rage game PCB set (board stack) is responsible for the display graphics and game play. Failure of the game PCB set may result in erratic or no game play. If this is the case, repair or replace the game PCB set by following the removal and installation steps below.

  • Turn off power to the game.
  • Disconnect the harness connectors from the game PCB set. (There are 5 connectors in all.)
  • Movement of the game PCB may be hindered by the joystick and button harnesses. If this is the case, disconnect the harnesses. 4, Unfasten the hardware that secures the game PCB set to to its mounting. Remove the game PCB set. wa Re-install the game PCB set by following the previ- Gus steps in the reverse order.
Page 33

Prima Race UNiversal Kit ¢ CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

CAUTION Before handling static-sensitive components, properly ground yourself to discharge buildup of static charges.

Power Supply The power supply is responsible for providing power to all of the game assemblies that require it. Failure of the power supply may result in erratic game play or no power at all. If this is the case, repair or replace the power supply assembly by following the steps below.

WARNING

A power supply can contain high voltages even after the power is turned off. To avoid injury, observe all of the safety precautions before working on the power supply. (Refer to the Introduction in the Maintenance Procedures section.)

  • Unplug the game from its AC power source. 2, Disconnect the wiring harnesses from the power supply.
  • Unfasten the screws that secure the power supply assembly to the cabinet, and remove the power supply assembly. To re-install the power supply assembly, follow the previous steps in the reverse order.

ROMs/RAMs The ROMs and RAMs contain the programming routines used by the game PCB set to control game play. Refer to Table 3-2 ROMs and RAMs Troubleshooting to determine the ROMs or RAMs that are malfunctioning. Replace the damaged ROMs or RAMs by following the removal and installation steps below.

  • Remove the game PCB set according to the procedure in the Primal Rage Game PCB Set section.
CAUTION Before handling static-sensitive components, properly ground yourself to discharge buildup of static charges.
  • Remove the damaged ROMs and RAMs from the game PCB set using a chip extraction tool.
  • Instali the new ROMs and RAMs by plugging them in the game PCB set sockets.
  • Re-install the game PCB set by following the steps. in the Primal Rage Game PCB Set section in the reverse order.

Video Display To repair, replace or make adjustments to the video display, follow the removal and installation steps below. These instructions are for your general information only. Please refer to the documentation that came with your video display before beginning any repairs.

High Voltage Video displays contain lethal high voltages. To avoid injury, do not service a display until you observe all precautions necessary for working on high-voltage equipment. X-Radiation Video displays are designed to minimize X-radiation. However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube (CRT) may implode if struck or dropped. The shattered glass from the tube may cause injury up to six feet away. Use care when handling the display and when removing it from the game cabinet. Also, wear gloves to protect your hands from the sheet-metal edges.

  • Discharge the high-voltage from the cathode-ray tube (CRT).
NOTE There may be a label on the video display assembly showing a circuit for discharging the high-voltage contained in the CRT to ground when the power is off.

a. Secure one end of a solid 18-gauge wire to a well-insulated or wooden handle screwdriver. b, Secure the other end of the wire to an earth ground, c. Briefly touch the blade end of the screwdriver to the CRT anode by sliding it under the anode cap. d. Wait 2 minutes and repeat the previous step.

Page 34

CHaPTER 3 — TROUBLESHOOTING AND MAINTENANCE % PwiMal Race UNtveRSAL Key

  • Disconnect all of the wire harnesses from the video 4. Install the new video display by following the predisplay. vious steps (excluding steps ta.-1d.) in the reverse order.
  • Remove the video display assembly from the cabinet 5. If necessary, adjust the new video display’s bright- . - _ ne: ze, centering, purity and convergence ,
CAUTION according to the video display service manual. Do not attempt to remove the video dis- ! play without its chassis.

Problem uggested Ac’

Coin Mechanism Problem Check the wiring connections to the coin mechanism. Check the voltage to the + side of the mechanism. Test the coin mechanism with the Controls Test screen in the self-test. Check the power distribution board fuses. SON

Joystick Problem Check the switches and potentiometers using the Controls Test in the self-test. Reset the limits on the joystick using the Controls Test in the self-test. Has the control been lubricated with the correct type of lubricant? If not, lubricate it Check the harnesses and connectors. If you took the control apart, have you reassembled it correctly? Make sure all the parts of the contro! are in good order. Repair or replace parts as needed. OO wna

Sound Problem Check the speaker volume setting: make sure the volume isn't zero! Check both parts of the Sound Board Test in the self-test Check the voltage on the JXPWR connector. Check the connections from the Quad Amp PCB to the speakers. Check the audio ROMs’ checksums in the Sound Board Test of the self-test procedure. Check the resistance of the speakers for 8 Ohms on the 4-inch speakers and 4 Ohms on the 8-inch woofer next to the coin box. 2 7Sen

Video Display Problem

Screen is dark Check to see that the game is plugged in and powered on. Check the line fuse if no power is present. Check the display brightness. Check the solder connections on the line filter and the transformer. Check the edge connector to the PCB. Check the harnesses and connectors to the video display PCB. Check the voltage levels to the video display PCB. Run through the following checklist. If you answer no to any question, you have a problem with the video display, not with the game circuitry. In this case, refer to your video display service manual. a. Do you have power to the video display? b. Are the video display's filaments lit? c. Do you have the correct voltage to the video display? ONOOAWN=

Only a colored screen appears Attempt to run a complete RAM/ROM test in the self-test. Replace the RAM if a RAM failure is reported in the self-test. No

Picture wavers or is too small Check the voltage levels to the video display PCB. ‘ Check the B+ to the video display. (Refer to the video display manual.) po

Table 3-1 General Troubleshooting

be a

Page 35

Primal RAGE Universal Kit & CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE

Problem Suggested Action

  • Check the bulb in the attract panel
  • Check the Power Distribution Board fuses. Attract panel does not light

Picture is wavy Check the connection of the monitor ground wire to the monitor. 1.

  • Check the connections of the sync inputs.
Picture is upside down or reversed1.If you replaced the monitor recently, check the horizontal or vertical yoke

wire connections to the video display. They may be switched.

Convergence, purity or color problems1.Use the self-test mode to digitally adjust the video display.
  • Use the adjustment procedures in your video display manual.
Picture is not centered1.Use the centering procedures in your video display manual.

Table 3-1 General Troubleshooting, Continued

Problem ROMs/RAMs Source and Purpose 0cai

ROMs

The program works, but the motionMotion Object ROMs and GALs (responsible for1S, 118-158, 9T,
objects are incorrect or non-existent.moving graphic objects)17P, 22U. Also,

ROMs on rows V, W

Garbage appears on the screen orProgram ROMs (responsible for game control)24L-29L

game play doesn't work correctly.

The text or numbers are incorrect orAlphanumeric ROM (responsible for controlling22P/R

non-existent. graphic text and numbers)

The sound is incorrect or non-existent.Audio ROMs (responsible for controlling sound)ROMs on Row 11 of

Sound CH31 board.

The moving backgrounds graphics arePlayfield ROMs (responsible for controlling background—25N-28N

incorrect or non-existent. graphics)

RAMs

The display color is yellow. Working RAM

The display color is green Video RAM

The display color is white. Color RAM

Table 3-2: ROMs and RAMs Troubleshooting

age Test Point or LED Location Voltage Source and Purpose

+5 + 0.25 VDC +5V Low, 5V High Logic power from the switching power supply.

Table 3-3 Voltage Inputs and Test Points

Page 36

CHAPTER 3 — TROUBLESHOOTING AND MAINTENANCE @ PRIMAL RAGE UNIVERSAL Kir

3-6

Page 37

CHAPTER 4

Parts Illustrations

ODUCTION

-HIS CHAPTER provides information When you order parts, give the part numyou need to order parts for your ber, part name, the number of this manu-

game. The printed-circuit board al, and the serial number of your game. (PCB) parts lists are arranged in With this information, we can fill your alphabetical order by component. order rapidly and correctly. We hope this Within each section the parts are will create less downtime and more

arranged numerically by part number. profit from your games,

Page 38

CHAPTER 4 — Parts ILLUSTRATIONS @ PRIMAL RAGE UNIVERSAL KIT

Figure 4-1 Primal Rage Kit Contents ‘A033660-01 A

Parts List

Qty.DescriptionPart No.Qty.DescriptionPart No.
1JAMMA Filter PC Board Assy.A047292-011Primal Rage Board Stack Assy.A053926-01
1Product I.D. Label038158-0112#10 Flat Washers
1FCC Compliance Label039450-0112#10-24 Zine Nut/Washer Assemblies
1FBI Warning Label042452-0112#10-24 Carriage Bolts
1Black Bezel for Kits049774-011#10 Wire and Cable Ties178032-002
1Vi6-inch Polycarbonate Control4Red Button Assembly178237-001
Panel Cover054307-014Yellow Button Assembly178237-002
2Side Panel Decal053652-012“Quick” Indicator Plate178283-019
1Attraction Film053403-022“Fierce” Indicator Plate178283-021
1Control Panel Decal053402-022Inverted “Fierce” Indicator Plate178283-024
1Instruction Label052893-01

2 Inverted “Start/Quick” Indicator Plate 178283-026

250-inch I.D. Split Ferrite Beads141026-00112#10-24 x 34-inch Long Carriage Bolts 75-5112B
8Snap-Action Switch160044-9011Primal Rage Universal Kit Installation
2Joystick Assy.171128-003,InstructionsTM-397,
1Attraction Shield047205-01
1Bezel Label053942-01Note: A JAMMA harness is not included in this kit. If your

game cabinet does not already have a JAMMA harness installed in it, you can order this harness from Atari Games Customer Service. Packaging materials are not listed above.

NOTE If you are installing this kit into a Showcase 33 cabinet, see page iii of this manual for additional parts you may need io order.
Page 39

Prima Race UNiversat Kir @ Cuaprer 4 ~ Parts ILLustRations

A053304-01 CH31_2 Stereo PCB Assy. 178291-614 #6 x .875 Alum. Seif-Clinching Spacer (7 places) 172025-3620 #6-32 x 1.25 Cross-Rec. Zino Pan-Hd. Screw ‘A053602-02 (7 places) Re GT24MB PCB Assy. 175017-2013 #6 Zinc Spring Lock Washer (12 places) 175014-1021 141 x 281 Steel/Zinc Flat Washer (7 places) A047292-01 JAMMA Filter PCB Assy.

178017-2013 ‘ 052894-01 #6 Zine tie é PCB Plate Spring Lock Washer A (2 places) rg 175014-1021 ho 141 x.281 Steel/Zine Flat Washer 172025-3610 (A051512-03 (2 places) #6-32 x 5/8” Cross-Rec. Primal Rage 172025-3606 Zine Pan-Hd. Screw Game (GT) PCB Assy. 46-32 x 3/8" Lg Cross-Recessed sree pee (Mask ROM Version) Pan-Hd. Screw #6 Zinc Spring Lock Washer (2 places) (3 places) 175014-1021 141 x 281 Steel/Zinc Flat Washer (3 places)

Figure 4-2 Board Stack Assembly A053926-01

Page 40

Cuaprer 4 — Parts ILLUSTRATIONS PRIMAL RaGr Unrversat KIT

«yes,Sol,Nt‘"ee.7
CRSgS TesVESmoQSAaamaoele BS cmc 2
"#eeeeee,a.

Don om Fao hyo

Blea=|}dR
a.-yhogwee ||&||oo
is]|Bse}iS}del[slPlsPa
=]|x][5]|¥WoT5EyiadaSku Sm

HI a8 © lores

Syetad8srt

4 anal | 2 |

&

: For best display quality, install all 4 jumpers in the low position (on 12 pins 1 and 2) for low-impedance monitors such as Neotec. Install all 4 jumpers in the ‘2 high position (on pins 2 and 3) for high-impedance monitors such as Wells-Gardner.

Figure 4-3 Primal Rage Game (GT) PCB Assembly A051512.04

Page 41

PRIMAL RAGE Universat Kir CHaprer 4 — Parts Intustrations

Primal Rage Game PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No,natorDescriptionPart No.

1/2H, 1/2M,

1H., 1MSocket, Zip 28179302-0281Pr, EPROM, 512KX8, 100 ns. Moh 0 1€39 136102-0301
1sSocket, 20 Pin, 300, Dbl Wipe179356-03201Pr, EPROM, 512KX8, 100 ns, Mol 0 2C11 136102-0300
2H., 2M, 3/4H, 3/4M, 3H, 3M, 4H., 4M1Pr, EPROM, 512KX8, 150 ns, PFOM Xxxx 136102-0051
Socket, Zip 28179302-0281Pr, EPROM, 512KX8, 150 ns, PFOL Xxxx _136102-0050.
5BSocket, 28 Pin, 300, Dbl Wipe179356-0328

1 Pr, EPROM, 512KX8, 150 ns, PFOH Xxxx 136102-0052

SFSocket, 20 Pin, 300, Dbl Wipe179356-03201Pr, EPROM, 512KX8, 100 ns, Pgm LI
5NSocket, 16 Pin, 300, Dbl Wipe179356-0316Xxxx136102-0041
7BSocket, 28 Pin, 360, Dbl Wipe179356-03281Pr, EPROM, 512KX8, 100 ns, Pam Um
7KSocket, 24 Pin, 300, Dbl Wipe179356-0324XXxX136162-0043,

1/2M Integrated Circuit, VRAM, 256KX4, 100 ns 137682-100

8BSocket, 28 Pin, .300, Dbl Wipe179356-0328,
8K, 9NSocket, 20 Pin, 300, Dbl Wipe179356-03201BIntegrated Circuit, 74LS11137149-001
orSocket, 68 Pin, PGA for 68PLCCIcIntegrated Circuit, 7406137052-001
Integrated Circuit179237-068IEIntegrated Circuit, 7418244137038-001
10M,11K,11S. Socket, 20 Pin, .300, Dhl Wipe179356-0320KIntegrated Circuit, 74F157137494-001
12BSocket, 28 Pin, .600, Dbl Wipe179356-0628IMIntegrated Circuit, VRAM, 256KX4, 100 ns 137682-100
12F,12HSocket, 28 Pin, 300, Dbl Wipe179356-03281NIntegrated Circuit, 74F08137483-001
12KSocket, 24 Pin,300, Dbl Wipe179356-0324IRIntegrated Circuit, 74F1603137345-001
128,13M,138 Socket, 20 Pin, .300, Dbl Wipe79356-03202ARes, R2R10, 1K/2K, SIP10118015-001
14KSocket, 24 Pin, 300, Dbl Wipe179356-03242BIntegrated Circuit, 741827137062-001
148, 15SSocket,e179356-03202cIntegrated Circuit, 74HCT273,137655-001
16F, 16H.Socket, 28 Pin, .300, Dbl Wipe179356-03282EIntegrated Circuit, 7418157137029-001
7P,17SSocket, 20 Pin, .300, Dbl Wipe179356-03202KIntegrated Circuit, 74F157137494-001
20D, 20R/S_ Socket, 68 Pin, PGA for 68PLCC2MIntegrated Circuit, VRAM, 256KX4, 100 ns 137682-100
Integrated Circuit179237-0682NIntegrated Circuit, 74F08137483-001
21K, 21M/N Socket, 28 Pin, .300, Dbl Wipe179356-03282RIntegrated Circuit, 7415377137145-001
22ASocket, 20 Pin, 300, Dbl Wipe179356-032028Integrated Circuit, 74F378137612-001
22DSocket, 28 Pin, .300, Dbl Wipe179356-0328
2UIntegrated Circuit, 74F163137345-001
22ESocket, 20 Pin, .300, Dbl Wipe179356-03203/4MIntegrated Circuit, VRAM, 256KX4, 100 ns 137682-100
22HSocket, 24 Pin, .600 Dbl Wipe179356-06243ARes, R2R10, 1K/2K, SIP10118015-001
22UB, 23F,3BIntegrated Circuit, 74L$27137062-001
24ESocket, 20 Pin, .300, Dbl Wipe179356-0320
24HSocket, 32 Pin, .600, Dbl Wipe179356-06323CIntegrated Circuit, 74HCT273137655-001
3EIntegrated Circuit, 74LS137029-001
25ESocket, 24 Pin, .300, Dbl Wipe179356-03243KIntegrated Circuit, 74F157137494-001
26H.Socket, 32 Pin, .600, Dbl Wipe179356-06323MIntegrated Circuit, VRAM, 256KX4, 100 ns 137682-100
277. 27USocket, 40 Pin, .600, Dbl Wipe179356-0640
28H, 29HSocket, 32 Pin, .600, Dbl Wipe179356-06323NIntegrated Circuit, 74F08137483-001
3RIntegrated Circuit, 74F377137622-001
JXBUS,Shroud, 96CKT DIN41621179369-009638Integrated Circuit, 74F157137494-001
++1005V1_ Test Point179051-0013UIntegrated Circuit, 74F378137612-001
1Pr, 1020-68PLCC Fpga, 20D Xxxx136101-10054ARes, R2R10, 1K/2K, SIP10118015-001
1Pr, EPROM, 128KX8, 100 ns, Alpha4BIntegrated Circuit, 74L$27
Xxxx136102-00454CIntegrated Circuit, 74HCT27.
1Pr, EPROM, 512KX8, 100 ns, Pgm Lm.4EIntegrated Circuit, 74LS157137029-001

‘XXXX 136102-0042

1Pr, EPROM, 312KX8, 100 ns, Pgm UuAKIntegrated Circuit, 74F157137494-001
XXXx136102-00444MIntegrated Circuit, VRAM, 256KX4, 100 ns 137682-100

a

Page 42

CuarTer 4 — Parts ILLUSTRATIONS & PRIMAL RaGE UNiversat Kit

Primal Rage Game PCB Assembly, Continued Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
4NIntegrated Circuit, 74F32137486-00110RIntegrated Circuit, 74F04137437-001
4RIntegrated Circuit, 7418377137145-00111D, 11EIntegrated Circuit, 74F273137610-001
11NIntegrated Circuit, 74F04137437-001
4sIntegrated Circuit, 74F157137494-001
4UIntegrated Circuit, 74F163137345-00111uIntegrated Circuit, 74F163137345-001
5DIntegrated Circuit, 7415245137134-00112D, 12EIntegrated Circuit, 74F374137420-001
SEIntegrated Circuit, 7418157137029-00112HIntegrated Circuit, SRAM, 32KX8,

25 ns, 3 137670-025

5]Integrated Circuit, 74F08137483-00112MCrystal, 28.636 MHz, Osc. Module144008-009

5K, 5M _ Integrated Circuit, 74F157 137494-001

5RIntegrated Circuit, 7418244137038-00112NIntegrated Circuit, 74F74137436-001
58,5UIntegrated Circuit, 74F169137496-00112PIntegrated Circuit, 74F273137610-001
12UIntegrated Circuit, 74F163137345-001
5VHI,SVLO LED, Red, T1-3/4, Diffused, MCD,13/14E,13D Integrated Circuit, 7418245137134-001

80-Deg 138021-001

6DIntegrated Circuit, 74F374137420-001BKIntegrated Circuit, 74F32137486-001
6EIntegrated Circuit, 74LS157137029-00113NIntegrated Circuit, 74F74137436-001
6F, 6K, 6M_ Integrated Circuit, 74F157137494-00113PIntegrated Circuit, 74F374137420-001
13UIntegrated Circuit, 747163137345-001
6NIntegrated Circuit, 74F32137486-001
6RIntegrated Circuit, 7418244137038-00114/15EIntegrated Circuit, 74F273137610-001
6sIntegrated Circuit, 74F260137570-00114A, 14BIntegrated Circuit, 7418257137136-001
ouIntegrated Circuit, 747377137622-00114DIntegrated Circuit, 74F273137610-001
14MIntegrated Circuit, 74F00137327-001
7DIntegrated Circuit, 7418245137134-001
JEIntegrated Circuit, 7418157137029-00114NIntegrated Circuit, 74F157137494-001
JE 7Integrated Circuit, 74F153137492-00114PIntegrated Circuit, 74F374137420-001
7MIntegrated Circuit, 741874137023-00114UIntegrated Circuit, 74F163

15A, 15B___ Integrated Circuit, 7418257

JNIntegrated Circuit, 74F32137486-001
7RIntegrated Circuit, 74708137483-00115DIntegrated Circuit, 74F374137420-001
7SIntegrated Circuit, 74F377137622-00115KIntegrated Circuit, 74F153137492-001
TUIntegrated Circuit, 74F169137496-00115MIntegrated Circuit, 74F86137649-001
15NIntegrated Circuit, 74F153137492-001
8DIntegrated Circuit, 74F374137420-001
8EIntegrated Circuit, 7418157137029-00115PIntegrated Circuit, 74F374137420-001
8F, 8)Integrated Circuit, 74F153137492-0011sUIntegrated Circuit,74F163137345-001
8MIntegrated Circuit, 74F174137531-00116A, 16BIntegrated Circuit, 748257137136-001
16DIntegrated Circuit, 7418245,137134-001
8NIntegrated Circuit, 74F08137483-001
8RIntegrated Circuit, 74F02137481-00116EIntegrated Circuit, 747374137420-001
9DIntegrated Circuit, 7418245137134-00116H.Integrated Circuit, SRAM, 32KX8,
9EIntegrated Circuit, 7418157137029-00225 ns, 3137670-025
16KIntegrated Circuit, 741804137009-001
OF,Integrated Circuit, 74F153137492-00116M, 16NIntegrated Circuit, 74F153137492-001
9KIntegrated Circuit, 74F260137570-001
OMIntegrated Circuit, 747163137345-00116PIntegrated Circuit, 74F151137490-001
ORIntegrated Circuit, 74F00137327-001168Integrated Circuit, 74F374137420-001
16UIntegrated Circuit, 74F244137502-001
10DIntegrated Circuit, 74F374137420-00117aIntegrated Circuit, 7418273137040-001
10EIntegrated Circuit, 7418157137029-001
10F, 10JIntegrated Circuit, 74F153137492-00117BIntegrated Circuit, 7418148137417-001
10KIntegrated Circuit, 741886137079-00117EIntegrated Circuit, 7418245137134-001
17KIntegrated Circuit, 741815713729-001
10NIntegrated Circuit, 7418163 A137114-00117M, 17N__Integrated Circuit, 74F153137492-001

4-6

Page 43

PRIMAL RAGE Universal Kir & Cnaprer 4 — Parts ILLUSTRATIONS

Primal Rage Game PCB Assembly, Continued Parts List

Desig- Desig-

nator _ DescriptionPart No.nator _ DescriptionPart No.
24B, 24DIntegrated Circuit, 74F245137591-001
iuIntegrated Circuit, 74F244137502-001
18B, 18DIntegrated Circuit, 7418245,137134-00124HIntegrated Circuit, SRAM, 32KX8, 70 ns, .6 137615-070
18EIntegrated Circuit, 74F04137437-001258Integrated Circuit, 7418245137134-001
18FIntegrated Circuit, 741874137023-00125BIntegrated Circuit, 74F245137591-001

26H Integrated Circuit, SRAM, 32KX8,

18HIntegrated Circuit, 74F138137521-00170 ns, 6137615-070

18K, 18M _ Integrated Circuit, 74F153 137492-001

18NIntegrated Circuit, 7415163 A137114-001278Integrated Circuit, 74F163137345-001
18UIntegrated Circuit, 74F163137345-001arIntegrated Circuit, SOS137550-001
270Integrated Circuit, Pfhs137419-104
19AIntegrated Circuit, DS1232137762-00128BCrystal, 50.009 MHz, Osc. Module144008-005
19BIntegrated Circuit, 7418273137040-001
19EIntegrated Circuit, 741874137023-00128DIntegrated Circuit, CPU, 68EC020,
19FIntegrated Circuit, 74F138137521-00125 MHz, 100PQFP137691-025
28EIntegrated Circuit, LM613137746-001
19K, 19M — Integrated Circuit, 7418245137134-00128HIntegrated Circuit, SRAM, 32KX8, 70 ns, .6 137615-070
19NIntegrated Circuit, 74L$163 A137114-001298Integrated Circuit, 74F20137530-001
19UIntegrated Circuit, 74F163137345-001
20EIntegrated Circuit, 74F08137483-00129HIntegrated Circuit, SRAM, 32KX8,

70 ns, .6 137615-070

20FIntegrated Circuit, 74F138137521-00129NIntegrated Circuit, 741$298137201-001
20K, 20MIntegrated Circuit, 7418374137144-00129PIntegrated Circuit, 7418153137104-001
20NIntegrated Circuit, 7418163 A137114-001298Integrated Circuit, 7418298137201-001
20PIntegrated Circuit, 7418378137305-001
APr, Fpla, 20NS, 9T 446D136094-0004
20R/SIntegrated Circuit, CPU, PLCC137658-101
20uIntegrated Circuit, 74F163137345-001APr, GALIOV8, 25NS, 11K 72ED136101-0011
21/228Integrated Circuit, 74F04137437-001APr, GALIGV8, 10NS, 22UB 3863136101-1220
21BIntegrated Circuit, 7418245137134-001APr, GALI6V8, 15NS, 22A 248 A136101-0021
APr, GALI6V8, 15NS, 23E 75C3136101-0013

21K,21M/N Integrated Circuit, SRAM, 32KX8,

25 ns, 3137670-025APr, GALI6V8, 25NS, 12S 4481136094-0014
2pIntegrated Circuit,137145-001APr, GALIG6V8, 25NS, 9N SAED136101-0012
21UIntegrated Circuit, 74F163137345-001APr, GALI6V8, 25NS, 17S 3139136094-0007
228Integrated Circuit, 7418245137134-001APr, GALI6V8, 25NS, 13M 5C94136101-1008
22DIntegrated Circuit, SRAM, 8KX8, 25 ns, .3 137667-025APr, GALIOV8, 25NS, 17P 270 A136094-0015
22HIntegrated Circuit, 28C16-200, 200 ns137648-200APr, GALIOV8, 25NS, 118 25F2135094-0016
22K, 22MIntegrated Circuit, 7418245137134-001APr, GALIOV8, 25NS, 24E 477 A136101-0018
22NIntegrated Circuit, 7415378137305-001APr, GALI6V8, 10NS, 18 B535136101-0006
228Integrated Circuit, 74F04137437-001APr, GALIOV8, 25NS, 10M 326F136101-0009
22U,23/24U Integrated Circuit, 7418273137040-001APr, GAL20V8, 25NS, 7K 9CA6136101-0019
23AIntegrated Circuit, 7418244137038-001APr, GAL22V10, 10NS, 25E D358136101-0017
23BIntegrated Circuit, 7418273137040-001APr, GAL22V10, 15NS, 12K 7553136101-1022
23DIntegrated Circuit, 7418245137134-001APr, PROM, 825147, 138 76B6136094-0001
23HIntegrated Circuit, 74F32137486-001APr, PROM, 828147, 14S FD85136094-0002
23K, 23MIntegrated Circuit, 7418374137144-001APr, PROM, 825147, 15S 9B61136094-0003
23NIntegrated Circuit, 7418378137305-001

ADCI Connector, 2 Circuit, Header, .100 Ctr 179048-002

23PIntegrated Circuit, 74LS157137029-001
23RIntegrated Circuit, 7418377137145-001ALPHASocket, 32 Pin, .600, DbI-Wipe179356-0632
24Integrated Circuit, 7418245137134-001

ES a

Page 44

CHapTer 4 — Parts ILLusTRATIONS @ PRIMAL RAGE UNIVERSAL KIT

Primal Rage Game PCB Assembly, Continued Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
ANLO.Resistor, 10 Q, 25%, 1/8 W110027-100JSYNC1Connector, 3 Ckt, Header, .100 Ctr179048-003

JWwIs Connector, 2 Circuit, Header, 100 Ctr 179048-002

BPr, GALIOV8, 25NS, 22E B82E136101-1025
BPr, GALIGV8, 25NS, 8K SADE136101-0010JXBUSConnector, 96 Ckt, Rept, Pressfit, Long 179368-0096

JXPWR Connector, 9 Ckt, Header, .156 Ctr, Rt,

€1,C2Capacitor, 100 pF, 100 V, 45%, Ceramic 122010-101Key 3179165-009

C3 Capacitor, 100 pF, 16 V, Flectrolytic,

Axial124008-107M28M, M48M, M148M, M248M
C4Capacitor, .1 pF, 50 V, +80%-20%, Cer. 122002-104Resistor, 10 Q, £5%, 1/8 W110027-100

C4M1-C4M5, C4MP Capacitor, 47 pF, 100 V, #5%, Ceramic 122016-470

C58 Capacitor, 01 pF, 50 V, +80%-20%, Cer. 122002-103 C7M1-C7M4, C7MA, C7MN Capacitor, 47 pF, 100 V, #5%, Ceramic 122016-470

C9-C12Capacitor, 1000 pF, 100 V, +10%, Cer.122015-102
C13-C15.—Capacitor, 270PFC, 50 V, EMI Filter140006-271

c16 Capacitor, 100 pF, 100 V, £5%, Ceramic 122016-101 cy Capacitor, .1 pF, 50 V, +80%-20%, Cer, 122002-104 cis Capacitor, .01 HF, 50 V, #80%-20%, Cer. 122002-103 c19 Capacitor, .1 pF, 50 V, +80%-20%, Cer. 122002-1

€20, C21 Capacitor, .01 pF, 50 V, +80%-20%, Cer. 122002-103 €22, €23 Capacitor, .1 pF, 50 V, £80%-20%, Cer. 122002-104 €24-C31 Capacitor, 01 pF, 50 V, #80%-20%, Cer.122002-103 €32-C37_— Capacitor, .1 iF, 50 V, £80%-20%, Cer. 122002-104

C38-C41_— Capacitor, 01 HE, 50 V, #80%-20%, Cer. 122002-103 C42-C50 Capacitor, .1 pF, 50 V, +80%-20%, Cer. 122002-104 C51, C52 Capacitor, .01 pF, 50 V, £80%-20%, Cer. 122002-103 €53-C60— Capacitor, .1 pF, 50 V, #80%-20%, Cer. 122002-104

C61, C62 Capacitor, .01 pF, 50 V, +80%-20%, Cer. 122002-103 €63-C317, C319, C321, C323, C326, C328, C330, C332 Capacitor, .1 IF, 50 V, £80%-20%, Cer. 122002-104

CMOO-7 — Capacitor, 47 pF, 100 V, +5%, Ceramic 122016-470

CRI, CR2Diode. 1N4001131048-001

EC25C, EC25X, EE2K Resistor, 10 Q, 5%, 1/8 W 110027-100

GNDI-7 _ Test Point 79051-001

J3 Connector, 2 Circuit, Header, .100 Ctr 179048-002 JAUD Connector, 6 Ckt, Header, JMPWR Ctr, Key 3. 179213-006 Connector, 9 Ckt, Header, .156 Ctr, Rt, Key 3 179165-009

JPLIConnector, 15 Ckt, Header, 100 Ctr179118-015

JRBUS Connector, 96 Ckt, Rept, Pressfit, Long 179368-0096

JRBUS)Shroud, 96CKT, DIN41621179369-0096

JRES Connector, 2 Circuit, Header, .100 Ctr 179048-002

rS o MOH_0-MOH_7, MOL_0-MOL_?, PFOH, PFOL, PFOM, PF1H, PFIL,

PFIMSocket, 32 Pin, .600, Dbl Wipe179356-0632

PGM_LL — Socket, 32 Pin, 600, Dbl Wipe 179356-0632

PGM_LMSocket, 32 Pin, .600, Dbl Wipe179356-0632
PGM_UM3600, Dbl Wipe179356-0632
PGM_UUSocket, 32 Pin, .600, Dbl Wipe179356-0632
Q1-Q3Transistor, 2N3904133041-001
Q4,Q5Transistor, 2N5306133033-001

PFOB, PF56B, PFR4M Resistor, 10 Q, 5%, 1/8 W 110027-100

R1Resistor, 470 Q, £5%, 1/8 W110027-471
R2Resistor, 75 Q, £5%, 1/8 W110027-750
R3Resistor, 470 Q, £5%, 1/8 W110027-471
R4Resistor, 10 Q, £5%, 1/8 W110027-100

R4M1-R4M5, RAMP Resistor, 47 Q, 45%, 1/8 W 110027-470

RS‘or, 100 Q, £5%, 1/8 W110027-101
RGor,LKQ, £5%, 1/8 W110027-102
RTResistor,2.4 K Q, £5%, 1/8 W110027-242
R7MAResistor, 47 Q, £5%, 1/8 W110027-470
RBResistor, 75 Q, #5%, 1/8 W110027-750
ROResistor, 10 Q, #5%, 1/8 W110027-100
R10Resistor, 100 Q, #5%, 1/8 W110027-101
RilResistor, 1 K Q, £5%, 1/8 W110027-102
Ri2Resistor, 2.4 K Q, +5%, 1/8 W110027-24
RBResistor, 75 Q, £5%, 1/8 W110027-750
R14Resistor, 10 Q, £5%, 1/8 W110027-100
RISResistor, 100 Q, 25%, 1/8 W110027-101
R16Resistor, 1 K Q, £5%, 1/8 W110027-102
RI?Resistor, 2.4 K Q, £5%, 1/8 W110027-242
R18Resistor, 0 Q, 45%, 1/4 W119005-001
R19, R20Resistor, 1 K Q, 15%, 1/8 W110027-102
R20DResistor, 10 Q, #5%, 1/8 W110027-100
R21Resistor, 470 Q, #5%, 1/8 W110027-471
R22-R25Resistor, 1 K Q. 45%, 1/8 W110027-102
Page 45

Primat RAGE Universat Kir & Cuarrer 4 — Parts ILLUSTRATIONS

Primal Rage Game PCB Assembly, Continued Parts List

Desig- Desig-

natorDescriptionPartNo.natorDescription
R26, R27__Resistor, 470 Q, +5%, 1/8 W110027-471RI78Resistor, 47 Q, 5%, 1/8 W110027-470
R28-R35Resistor, 1 K Q, #5%, 1/8 W110027-102R179, R180 Resistor, 10 K Q, +5%, 1/8 W110027-103
R36-R45Resistor, 470 Q, 5%, 1/8 W110027-471R181Resistor, 4.7 K Q, +5%, 1/8 W110027-472
R46Resistor, 1 K Q, +5%, 1/8 W110027-102R184Resistor, 10 K Q, +5%, 1/8 W110027-103
R47Resistor, 470 Q, +5%, 1/8 W110027-471R186Resistor, 1 K Q, 5%, 1/8 W110027-102
R48, R49_—_-Resistor, 1 K Q, £5%, 1/8 W110027-102R188Resistor, 10 Q, +5%, 1/8 W110027-100
R50-R57Resistor, 470 Q, #5%, 1/8 W110027-471R189Resistor, 470 Q, +5%, 1/8 W110027-471
R58-RO8Resistor, 1 K Q, £5%, 1/8 W110027-102R190Resistor, 10 K Q, 5%, 1/8 W110027-103
ROOResistor, 470 Q, +5%, 1/8 W110027-471R191, R192 Resistor, 1 K Q, +5%, 1/8 W110027-102
R70-R77_—_Resistor, 10 K Q, 45%, 1/8 W110027-103R194Resistor, 470 Q, +5%, 1/8 W110027-471
R78-R83Resistor, 1 K Q, +5%, 1/8 W110027-102R196Resistor, 1 K Q, +5%, 1/8 W110027-102
R84Resistor, 4.7 K Q, +5%, 1/8 W110027-472R202Resistor, 47 Q, +5%, 1/8 W110027-470
R85-R97Resistor, 1 K Q, +5%, 1/8 W110027-102R204Resistor, 4.7 K Q, +5%, 1/8 W110027-472
R98-R109Resistor, 470 Q, +5%, 1/8 W110027-471R205Resistor, 47 Q, +5%, 1/8 W110027-470
R110-R123 Resistor, 10 Q, #5%, 1/8 W110027-100R207, R208, R210, R211, R214, R217, R218
R124Resistor, 100 Q, +5%, 1/8 W110027-101Resistor, 10 K Q, +5%, 1/8 W110027-103
R125Resistor, 220 Q, +5%, 1/8 W110027-221RMOO-RMO7
R126, R127 Resistor, 100 Q, #5%, 1/8 W110027-101Resistor, 47 Q, +5%, 1/8 W110027-470
R128Resistor, 10 K Q, £5%, 1/8 W110027-103RVGNDResistor, 0 Q, +5%, 1/4 W110005-001

R129, R130 Resistor, 10 Q, +5%, 1/8 W 110027-100

SW1Switch, Slide, SPDT160040-001
R131Resistor, 1 K Q, +5%, 1/8 W110027-102
R133Resistor, 470 Q, +5%, 1/8 W110027-471VCRIConnector, 2 Circuit, Header, .100 Ctr 179048-002
R134Resistor, 4.7 K Q, #5%, 1/8 W110027-472
R136Resistor, 10 K Q, +5%, 1/8 W110027-103WDOKLED, Red, T1-3/4, Diffused, SMCD,

80-Deg 138021-001 R137, R138 Resistor, 220 Q, +5%, 1/8 W 110027-221

R139-R146_ Resistor, 10 Q,5%, 1/8 W110027-100X1Q2Resistor, 10 Q, +5%, 1/8 W110027-100

R147, R148. Resistor, 47 Q, +5%, 1/8 W 110027-470 R149, R152 Resistor, 1 K Q, 5%, 1/8 W 110027-102

R153Resistor, 2.2 K Q, +5%, 1/8 W110027-222
R154Resistor, 10 K Q, #5%, 1/8 W110027-103
R156-R158_ Resistor, 100 Q,+5%, 1/8 W110027-101
RIS9Resistor, 1 K Q, £5%, 1/8 W110027-102
R160Resistor, 10 Q,V3w110027-100

R161, R162 Resistor, 1 K Q, £5%, 1/8 W 110027-102

R163, R164 Resistor, 10 Q, +Vs Ww110027-100
R167Resistor, 510 Q, +5%, 1/8 W110027-510
R168Resistor, 10 Q, +5%, 1/8 W110027-100
R169Resistor, 10 K Q, +5%, 1/8 W110027-103
R170Resistor, 11.0 K Q, £1%, 1/4 W110034-1102
R171Resistor, 10.5 K Q, 1%, 1/4 W110034-1052
R172Resistor, 1 K Q, £5%, 1/8 W110027-102

R173 Resistor, 39 K Q, +5%, 1/8 W R174, R175 Resistor, 39.2 K Q, #1%, 1/4 W RI76 Resistor, 470 Q, #5%, 1/8 W

Page 46

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 47

PRIMAL RAGE Universal Kir CHaprer 4 — Parts ILLUSTRATIONS

GT24M8 PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
(HS1-HS3) Screw, Pan, 4-40X3/8, X-Rec, Cad17.2025-3206BNKDEC _ Socket, 20 Pin, .300, Dbl Wipe179356-0320
APr, GALI6V8, 10NS, Romdec 50F8136102-0260BS1, BS2___Res, 10 Q, +5%, 1/8 W110027-100
APr, GALI6V8, 15NS, Bnkdec 1FDO136102-0261

C1,C1A,C1B Capacitor, 100 pF, 16 V, Electrolytic, Axial 124008-107

APr, Mrom, 1MX8, 100NS, MOLO.2 SFC8_—136102-0320C2-C37,Capacitor, .1 pF, 50 V, +80%-20%, Cer, — 122002-104

A Pr, Mrom, IMX8, 100NS, MOLO.6 96C1 — 136102-0328

APr, Mrom, IMX8, 100NS,MOLO.4 90BD —136102-0324CTRMO-CTRM7
APr, Mrom, 1MX8, 100NS, MOLI.0 9FB6 — 136102-0332Capacitor, 47 pF, 100 V, +5%, Cer.122016-470
APr, Mrom, IMX8, 100NS, MOH1.2 40E9—136102-0337D245Res, 10 Q, +5%, 1/8 W110027-100
APr, Mrom, 1MX8, 100NS, MOHO.7 F538.136102-0331
APr, Mrom, IMX8,100NS, MOHO.1 89FO—136102-0319DBO, DB1, DB10, DB11
APr, Mrom, 1MX8, 100NS, MOLO.0 BO9E — 136102-0316Integrated Circuit, 74F245137591-001
APr, Mrom, IMX8, 100NS, MOLO.7 8285136102-0330GNDI-GND5
APr, Mrom, 1MX8, 100NS, MOHO.5 9060136102-0327Test Point179051-001
APr, Mrom, 1MX8, 100NS, MOLO.1 CF92—136102-0318
APr, Mrom, 1MX8, 100NS, MOH0.3 DSE7_ 136102-0323JBSO, JBS3_ Connector, 2 Ckt, Header, .100 Ctr179048-002

JPWRI Connector, 9 Ckt, Header, .156, Key 3, Rt_179213-109

APr, Mrom, IMX8, 100NS, MOL1.2 0777136102-0336
APr, Mrom, IMX8, 100NS, MOHO.6 87C4—136102-0329JRSZOConnector, 2 Ckt, Header, .100 Ctr179048-002

A Pr, Mrom, IMX8, 100NS, MOL1.3 0E47 — 136102-0338

APr, Mrom, IMX8, 100NS, MOLO.5 660E — 136102-0326MOHO0.0-MOHO.7, MOH1.0-MOHI.3, MOLO.0-MOLO.7, MOL1.0-MOL1.3

Socket, 32 Pin, .600, Dbl Wipe 179356-0632 A Pr, Mrom, 1MX8, 100NS, MOH0.0 9AB3__ 13612-0317

APr, Mrom, IMX8, 100NS, MOHO.2 B2A6 13602-0321RI-R4OResistor, 33 2, #5%, 1/8 W110027-330
APr, Mrom, 1MX8, 100NS, MOLO.3 D4DF —136102-0322RAlResistor, 4,7 QKx9, £2%, 1/8 W118010-472

A Pr, Mrom, IMX8, 100NS, MOH1.3 GAFB 136102-0339 ROMDEC _ Socket, 20 Pin, .300, Dbl Wipe 179356-0320 A Pr, Mrom, IMX8, 100NS, MOHI.1 E50C —136102-0335

APr, Mrom, IMX8, 100NS, MOLI.1 BA48—136102-0334RSZ1-RSZ3__ Res, 10 Q, +5%, 1/8 W110027-100

A Pr, Mrom, 1MX8, 100NS, MOH1.0 1D6 A 136102-0333

APr, Mrom, IMX8, 100NS, MOH0.4 F3EE —136102-0325RTRMO-RTRM7

Res, 47 Q, +5%, 1/8 W 110027-470

A245Res, 10 Q, #5%, 1/8 W110027-100

ABO-AB2, AB1O-AB12 Integrated Circuit, 74F245, 137591-001

B1M, B4M Res, 10K Q, +5%, 1/8 W 110027-103

B8MRes, 10 Q, #5%, V8 W110027-100

B11M,B14M Res, 10K Q, BI8M, B48M, B148M Res, 10 Q, 5%, 1/8 W 110027-100 , VeWw 110027-103

Page 48

CHapTeR 4 — Parts LLuSTRATIONS PRIMAL RAGE UNIVERSAL KIT

ATARI GAMES © 89 JAMMA FILTER PCB A047292-01 MADE IN USA

w“Yu2
:5Be:8g

J

1iBe2.u.g-a28

Figure 4-5 JAMMA Filter PCB Assembly A047292-01 B

JAMMA Filter PCB Assembly Parts List

Desig- Desig-

natorDescriptionPart No.natorDescriptionPart No.
C1-82200 pF, 50V, 3-Pin EMI Filter Cap.140006-22232, C33 270 pF, 50V, 3-Pin EMI Filter Cap.140006-271
C9, C10270 pF, 50V, 3-Pin EMI Filter Cap.140006-27134-462200 pF, SOV, 3-Pin EMI Filter Cap.140006-222
C11-312200 pF, SOV, 3-Pin EMI Filter Cap, 140006-222jlConnecior, 56 Ckt., .156 Ctr, RT179240-056

4-12

Page 49

CHAPTER 5

Schematic Diagrams

INTRODUCTION

f. HIS CHAPTER contains the sche- JAMMA Filter PCB. In addition, this chapter

matic diagrams for most of the includes a block diagram of the CH31

Primal Rage” game printed-circuit (CAGE Audio) PCB. The PCB assembly

boards, including the game PCB (also called drawings are illustrated in Chapter

the GT board), the GT24M8 PCB, and the 4, Parts Illustrations.

Page 50

Cuaprer 5 ~ SCHEMATIC DiaGrams Paimat Rar Universat Kit

Jy arres

ae

5-2 ono) anak Om on sets 8 Oa at Tawa-c Oe sv sea Ge oa Bea Gome =)

antes Om

oe rat

canna CE

oxo oe a

29 0

Figure 5-1 Primai Rage Game (GT) PCB Schematic Diagram 051511-01 Rev. J (Sheet 1) ts ow acta os acrrs 12 Ow acta 32 Ow acres 1 ow acta to Gm ars 3 oes 2 ow ox 7 mur 6 Ow sins 5 Ow coin sw senvices

2 Oey 2 Ow no

1 ow wseH.uT 2 Ow vsvac.out

Page 51

PRIMAL RAGE Universal Kir & CHAPTER 5 — SCHEMATIC DIAGRAMS

Figure 5-1 Primal Rage Game (GT) PCB Schematic Diagram, Continued 051511-01 Rev. J (Sheet 1)

Page 52

CHapTer 5 — SCHEMATIC DiAGRAMS @ PRIMAL RAGE UNIVERSAL KIT

vr ssi wo tia laeleo Tee Lig Tie Tee - Boab ete es 2 ki ane . ors [ours | rare] voro J roty ruts frors |rote gy seals | Heh,

urerTT zc ay 12.1015
vesradtaan

a if

ureraxmE 7 on
PtamaeHES
keadetfs we
=Te t%vas

Lew Leas Leasler Lee Leas Loe Ten pape paps pa papa pa en

assy a MogMbehens 20) 20h ei ais ane Eire ose "

acrea:4rTrs} Ts ay2z xo
ami1
acrearaieR6D i ay 2_mtt0
1ccma
fare=e7nt rs
fadra2:
srere+t iae z wt 108
omTen Ll™a

Los Ley Leslee Los Lee Les Dep POY Bo Lp Toe cp ef

" 164 PLS no ve agd ae wm Lantos Lun es pe mee 2 Mo gueteae eo wie __4f5 mato ne MO gg Neh i. SERVICES Teas se a ay 22107

tyaa ah
coun5aFC TC EY
onsmr ikEA
actu+ey 7 ts

ur ‘aa n rae 324 sort re Port ee aera ee

La(S257139,18

ce Lew Lea less Lose Lee Len Dose 12 ere ee pee ae Fa a [eb an ew nemo = #8 welilan Lee Tonlay Tue ie Beewehe 26) 2ueeis ee! aa. 1s Eh a as oo ag wee

acrt=Teeta gy e808
Gatmark io} $4,
‘gureies, wT| Se

pera a_i 634

acat*Te FTE ay 2 HO

pa ee sf atrial aa ra, BE ae yf #00

atet7=

i Lege Leg Lea Lege

eo age? a8 @ aad sal? wo 48 30 ofS 2 2} k in ad MK ace] users

Figure 5-1 Primal Rage Game (GT) PCB Schematic Diagram 051511-01 Rev. 1 (Sheet 9)

Page 53

Prima RAGE UNIVERSAL KiT & CHAPTER 5 ~ SCHEMATIC DIAGRAMS

xo103181

6 geome rea L Ree a7 5B. pope 4 ‘ COINL Bag carr

cane nes seueresr

  • res SER W

sk cis Lew ? i

ovo

+12v ua

cat ne figoor A oo: conn conn

Tarn ne : cone cet cree

Bissos * seo coe CONTR CONTR 758 ve | ial i TREO] oe xe) swocur cei 9] ssi % gacosos 7 aw toe a nue

neo 20.000 a ss

Shior hawis
teieG20Sous
uP2:ime3) ins,05 2M013
esegE IheOe IPStone
ttieG8molt
RTLLiRUT 28) wooz HSMO1O
PLRH_10K21) wtntM09
wte108qo28 two00 [2wow

LAREWSS_J socker vase) #]% aoe —

ADE RANGE

Figure 5-1 Primal Rage Game (GT) PCB Schematic Diagram, Continued 051511-01 Rev. D (Sheet 9)

5-5

Page 54

CHAPTER 5 ~ SCHEMATIC DIAGRAMS PRIMAL RAGE UNIVERSAL KIT

Figure 5-1 Primal Rage Game (GT) PCB Schematic Diagram 051511-01 Rev. J (Sheet 15)

5-6

Page 55

Primal RAGE Untversat Kit @& Cuaprer 5 — SCHEMATIC DIAGRAMS

Page 56

CHapTer 5 — SCHEMATIC DIAGRAMS % PRIMAL RAGE UNIVERSAL KIT

Pera oaza

me waee

tie eat

oa] cay

CC)

cea raze mae

mai

azo

mas

eae

as

ais

sae

ea

paz

rain

ma

ur

xo

oo ov

+0

nora

wore ome

oT j

sez seu —acn

oso ae <u

ais

nore

oo ais

Uma Pg LCE SICweea [28 state a YR STATE .
wos do~~

Roe Fyne cos ote

by ta oot==
me a aoaTa a00eWee aoace ioe a Wee sae 8
a a coryTs oes aa, ReS BOAS| ae * DEW wae
Caon‘art
rabeLapie“ane
arbereoata

res Loe ros Lo

Figure 5-2 GT24M8 PCB Schematic Diagram 053601-xx Rev. B (Sheet 1)

Page 57

Primal RaGe UNiversaL KiT @& CHAPTER 5 — SCHEMATIC DiAGRAMS

To sarhes4OND

° © wns wore :

toa/i40

co T 1 OL 1 ‘FORTE

oe8 | asf | os8 | 28 even ten cree

= 5 [Ss Is are TRG arene | eTRHO

L—§s puscaeaaBs
L__¢ putoine=

of

Figure 5-2 GT24M8 PCB Schematic Diagram, Continued 053601-xx Rev. B (Sheet 1)

ye Ne}

Page 58

CHAPTER 5 — SCHEMATIC DIAGRAMS @ PRIMAL RAGE UNIVERSAL KIT

sanzan9)

snopes

5-10 5 sae

m0)

Figure 5-2 GI24M8 PCB Schematic Diagram 053601-xx Rev. B (Sheet 2)

Page 59

PRIMAL RAGE UNIVERSAL Kit ¢ CHAPTER 5 — SCHEMATIC DIAGRAMS

Figure 5-2 GT24M8 PCB Schematic Diagram, Continued 053601-xx Rev. B (Sheet 2)

5-11

Page 60

CHapTer 5 — SCHEMATIC DiaGRAMS PxiMAL RAGE Universal Kit

io Nar |

ver momovr momaSt] ver mom 2
ADELE ey28 das
a2SIAaeShae
aunSAaEa
moPuig 2 aso2 Taso
asoy | 24_at01saosoy [210swar]| 2
aSog 19 10aSosZBuaasbs
onwelwed

+ +

roue stfwee meus silver wou ein 30-88 sao |

eam ae marae"

BIAS o Bag 26 vad

amar]on Etmas .on L2L

ow el if wo el woxoer « g@ —_1 TOROEZ

Figure 5-2 GI24M8 PCB Schematic Diagram 053601-xx Rev. B (Sheet 3)

5-12

Page 61

PRIMAL RaGe Universai Kir @& CHaprer 5 — SCHEMATIC DiaGRaMs

wine] a ECRTOOY

“ oa ETO] = © ys Binz

Figure 5-2 GI24M8 PCB Schematic Diagram, Continued 053601-xx Rev. B (Sheet 3)

5-13

Page 62

Cuaprer 5 — SCHEMATIC DiAGRAMS PRIMAL RaGe Universat Kir

FROM GAME BOARD

a 1 oe oan 2o 9 ono 3 oe esy 4 oe usy soa 0lsy 6 oa mez To Key 8 oa osenra? 9 ow J1L0cK2 10 Qe 2)5PKRD 1 Qe J1AUDGND 12 G——« JIGREEN 13 9 ——e DIST 1 Qe SERV ts oe DITILT 16 oe aicoIN 17 Ge DISTART? 18 90 JUP2A 13 oa J000N24 20 90 JULEFTEA 21 oe saz 2 oe JF IRE 23 oe 1028 24 oe J100NN28 25 oe JILEFTB 26 9 J1KT26 oT 90 wo 2 o—3 ano hoe Gh 8 oa Geo Coa ors 08 at45¥ foe ars Foe atiay ho wer 2 oe nok Ks diLorKt Loe D1SFRRI Hoe 2iAuoe Noe v2Re0 ° oe viatue Roe J1viDGND Soe v1surTst Ts DILCOIN vgs JasTaRTL vos tues Woe v100.N1 4 FO JILEFTIA Ys tat 2 oe SIFIREL ak Os 10718 86 oa 100WM18 cc oe J1LEFTIS 90 ¢ 3 2B te oe ano Fe 3 ano ca S881 @ ape a et 22007 cas

ssh ee is 2200PF

2s O18) pp a = 2200 car nevey x} rome sete 7 22009

28 = stoma? @ po sone 2200°F ¢29

yitocke «Fm atone = t 2200PF

PRL 9 ep aa L e2eaPe eat snyogn9, «$f arp st 22009F

oe 2 «np ten 270°F 95 ising =F pore sor a T 2r0FF

cue SER @ ep se X reo 35 garter @ Fe tr 72009

ce = Reoth «arp rn 2200°F cay susragte: eT rome ssa T= 22008

UPR oom 2200°F cag sro0en @ Ferre sounn = casorr

UEP 26 @ ange str 24 2en0Pe = cat ores @ Frm —e atten = 22009F

cee auriat? @— pe artate E e200PF ca suvree @ Fem —e art t ze00e

cae 028» ap = anowes 22007F cay

snucrtes Pepe tere Tt 22008 cas R28 @ ep = ates = 22009 a 21988 np ai 2200RF eg

098 none 22000

c: ans ry or? ce sist @ Fone iy = 22000F

c sneamtt @ rpm semtat = eeo0er os

sateen Ferre atocn L 2e0arF

o spehie » ep are re00PF cg ginute 9a sre 22009F

stvto640) @ erp a aviv 2200°F oye suetsy @ Fre aster d X zavee

aa suLCo1W » en po a uci E e200 cig

gustaany Le asa = T 22008F cas SURI, pero eur i 2200°F cis

sno0wnin @——F—eerpm sone 22009F

ar s1artté penne ester t 2e00PF ce statin @ frp —e sta © 200%

os SUFTREL 9 ep earn 22008F = co sunt ef —_~npn—e auris © zz0ore

cat 200M @—an pm —__—_ sons LE ze00F cae saveenis @ Frome terns 22009F

cea aT» pe ze009F

Figure 5-3 JAMMA Filter PCB Schematic Diagram

5-14 047292-01 B

Page 63

PRIMAL RAGE UNIVERSAL KIT & CHAPTER 5 — SCHEMATIC DIAGRAMS

10 GAME HANES

av GAD ao ANNA (GD) Gk @——0 UANMA-B (GO) Js5V ao YAMA C45) 3857 ao AMA S) OSV eo UMMA 50) Suey a9 UNM G2) “5 nin KEY —o

enTRe a5 daee)—teeaTaA $0 8 wie

© ont ATS ote

BLOCKZ @——0 OANA CE-L9CKR JSPHRL @——O YANMAL (SPARK) IRUDGWD @——O JAMMA-N (SPAR) SIGREEN @——o ARMA. (GREEN) SOYNE wo AMMA? (SYNC SER a0 JAINA (SERVICED WUT eo vans «TILTD URCOIN g@——o OAMNA-T (COTW) SSTART2 @——0 DANMA-L—(STARTA) UPR @——o SAMMA-Y(UPRAD 0W2K @——O OANA (DONA SLEFTZA @——o OANA (LEFTRAD ARIZA pO UAMMA-Y—(RIGHTRAD SFIREZ @—— VANMA-Z—(RBUTTORIY WUP2B @——O UANNA-AA (RBUTTOR2) D0WN28 =——O UAMMA-B_(RSUTTONA} SLEFT2B @——o UANMA-CE (LEFTRBD ART2B gO ANMA-DDCRIGHTRBD GND @——0 JANKAEE (GND) GK eo JANMA-FF (GND? ro Mtb Mowe

oat Gk0 eo vawma-1 —C0ND? KO 0 DAMKA-2 (GND J+5¥ a0 UANMA3 (51) Bs5V eo ANNA (+50) O5¥ ao DANA'S 5H) Je12¥ po dam (41209 =O Jawa? KEY JOWTRT @——o ANMA-B (CENTLY LOCK @——O JANNA-9—(C-LOCKL) ASPHALY @——O UAMMATIO. (SPRRER) IAUDS gO SANMATL(SPRRELY RED @——o VANMA-12 (RED) BLUE BO daMMA-1d (BLUEY vi0eND @——o GANNARI4 (410. 6NOD SSLETST @——6 UAWA-15 (SELFTESTD SCCDIN a6 JAMMAIE(COINLD OSTARTL 26 OMA-I7 (STARTLD JUPIA @——0 UaMMMA-18 CPLA ‘sD0WHIA a——o IANA 19 (DOWNLAD SLEFTI6 a0 JMWA-20 CLEFTLA ARTA @——O JAMMA-21(RIGHTLAY SFIREL 30 aboa-22 <LaUTTONID 3UP13 @——o UAMMA-23CLBUTTONA) D0W18 @——O JAMA 26 CLBUTIONS) SLEFTIB @——o JMWA-25. (LEFTLB) ORTI3 @——O aMA-25 (RIGHTLAD GRD 0 SAMMA-27 (GND) GND @——0 MA-28 (GND)

Figure 5-3 JAMMA Filter PCB Schematic Diagram

047292-01 B

5-15

Page 64

Cuaptrer 5 - Scuematic DiaGRAMS @ PRIMAL RaGe Universal Kir

Connected pin f | HHI/ (III X-Bus Host Interface Power Connector

3 Code ROM E i=

§ & [

Fe ROMs DsP I ' « 1 ' amplifier ! (in Stereo j ! Version) :

Audio Out i [Ll ens ~~~ --

(Key) Left Channel + Left Channel — Right Channel + Right Channel — = Woofer — Land R channels drive 8-Ohm speakers. Woofer drives 4-Ohm speaker.

Woofer +

Figure 5-4 CH31_ 2 (CAGE Audio) Board Block Diagram

5-16

Page 65

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 66

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 67

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted. If the products described in this manual fail to conform to this warranty, Seller’s sole liability shall be, at its option, to repair, replace, or credit Buyer’s account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller’s plant; and
  • Seller’s examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation, or improper testing. In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari Games Corporation cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.

Page 68

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.