CATHODE RAY TOMES

Tank Cocktail TM-036

Tank/Tank Cocktail (Atari/Kee, 1974) · Technical Manual · 50 pages · 18 sections · original scan

Page 1

A SUBSIDIARY OF ATARI ATARI INC 14600 WINCHESTER BOULEVARD, LOS GATOS, CALIFORNIA 95030 - TELEPHONE (408) 374-2440 + TELEX 357-488)

Page 2

TABLE OF CONTENTS

SECTION 1 GENERAL MAINTENANCE INFORMATION

1.1

1.2

1.3

1-4

1.5

1.6

1.7

1.8

1.9

1.10 Introduction

Warranty

New Machine Setup Procedure

Interior Access

New Machine Checkout

Game Operation

TV Adjustments

Game Circuit Board Adjustments

Coin Acceptor

General Machine Maintenance

SECTION 2 SERVICE INFORMATION

2.1

2.2

2.4

2.5

2.6

2.7 Test Equipment

Required Equipment

Optional Equipment

Removal and Replacement. Procedures

Troubleshooting

PCB Shipping Procedures

Logic Types and Functions

SECTION 3 SCHEMATICS, DRAWINGS, AND PARTS LISTS PAGE

1-1

1-1

1-2

1-2

1-3

1-3

1-6

1-7

1-9

Page 3

Section 1

General Maintenance Information

1.1 INTRODUCTION

The Atari Tank game consists of a cocktail-table cabinet, TV monitor, two printed circuit boards (PCBs), interconnecting wiring, and various cabinetmounted circuit components. Except for a schematic and basic TV troubleshooting procedures, no information about the TV monitor is presented in this manual. The TV monitor is a Motorola XM501 unit. TV circuit malfunctions can be solved using the described standard TV troubleshooting techniques that may be familiar to the average technician. Therefore, the PCB information in this manual is dedicated mainly to minor adjustments and instructions on shipping boards to Atari, Inc. for servicing.

1.2 WARRANTY (same as printed on inside front cover)

Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors are free from defects in material and workmanship under normal use and service for 4 period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.

If the products described in this manual fail to conform to this warranty, Seller's sole liability shall be, at its option, to repair, replace, or eredit Buyer's account for such products which are returned to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
  • Such products are returned prepaid to Seller's plant; and
  • Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.

In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.

EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BETWEEN SELLER AND BUYER WHICH CONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS ORDER.

Page 4

1-3 NEW MACHINE SETUP PROCEDURE

Before turning this machine on, inspect it carefully for any damage that may have occurred during shipment, Inspect both interior and exterior of the machine for any obvious damage to the cabinet or internal components. Check for cracked or broken cabinet parts, assemblies pulling loose, broken or disconnected wires, or foreign objects shorting electrical connections. After the machine has been plugged in and turned on, perform the checkout procedure, Section 1-5.

1-4 INTERIOR ACCESS

All servicing is performed inside the machine through the hinged top that provides access to all components, sub-assemblies and adjustments with the exception of the coin box.

The coin door is located on the front of the machine underneath the control panel. To remove the coins, unlock the metal coin door, grasp the door lip and pull out the coin box.

To reach the interior of the machine, unlock coin door and reach upwards just inside the door opening. Near the top of the interior compartment is a cnain. Pull down o this chain and, with the other hand, lift up the hinged top. To hold top open, lift up metal support rod on the right side of base's top edge and insert end of rod into oval slot at right front side of TV chassis.

Please note that two interlock switches are provided for the game, so that the machine is completely turned off whenever either the top or coin door is opened. These switches protect the operator from accidental shock and so they must always be kept in perfect working order. If the machine is

1-2

Page 5

adjusted or tested with the rear door open, the interlock switches must be placed in the closed (or "on" position) by pulling out the white actuator shafts.

1-5

WARNING: The covered black terminal block carries full line voltage whenever the line plug is connected to a power outlet. This cover should be removed only with the line plug disconnected. Do not leave off the cover once it has been removed.

NEW MACHINE CHECKOUT

As each new machine leaves the factory, every component and subassembly is carefully checked for proper operation. However, since parts may have been damaged or adjustments changed during shipping, the following checkout procedure must be repeated prior to placing the machine on location:

A. Carefully inspect the interior of the machine to see that all solder joints, slip-on connectors and plug-in type connectors are firmly seated. Pay particular attention to the PCB edge connector, the fuses and any connectors to the potentiometers. Also check the connections to the coin switch, the TV monitor, the interlock switches and all the other Molex-type comnectors.

Plug the machine in, and pull out the white actuator shafts of the interlock switches if the rear door is open. Inspect the cathode ray tube (CRT) image for a steady and sharp picture that exhibits the proper levels of brightness and contrast.

Insert several old and new coins into the coin acceptor. No genuine coin should be rejected and each coin insertion should advance the coin counter one digit. Depress the coin rejector button to make sure the linkage is operating smoothly.

Coin insertion should start the game. Check for proper game sequence, making sure that all aspects of the game are functioning correctly.

The door locks should tum to the locked and unlocked positions smoothly and the doors should open and close without binding.

1-3

Page 6

F. The interlock switches must turn off the entire machine when the

rear door is opened.

1-6 GAME OPERATION

Inserting coins immediately starts the game with one tank in upper left area of the playfield and the other in lower right.

To move tank forward, push both joysticks forward. To stop tank, pull both joysticks back. To turn to right, pull right joystick back and push left joystick forward. Left turns are in opposite directions.

Illustrated instructions for the different motions are silkscreened on

front panel.

To fire shells, push down red button on right joystick. One point is scored each time a shell hits the other tank. If tank hits a mine, player's opponent gains one point and mine will disappear for remainder of that game. When a tank is hit by a shell or encounters a mine, an explosion sound is heard and tank flashes. Until flashing has stopped, player's opponent cannot fire another shell. About 20 seconds before game ends, score display will begin flashing and continue until game ends.

1-7 TV ADJUSTMENTS.

Monitor circuitry includes four stages of video amplification - a twostage audio amplifier, sync and deflection circuits, and a regulated power supply. An additional 5-volt supply is included to power the external logic system. The adjustment of the TV monitor functions like that of a normal TV set. The only exception is that the TV's audio portion is not used. The volume control is located on the PCB. The CRT image is adjusted through the top door.

A. Brightness: Adjust the brightness, then the contrast. Adjust so that the CRT background is as dark as possible.

1-4

Page 7

Contrast: Adjust so that images displayed on the CRT are as bright and clear as possible without being blurred or smeared.

Vertical Hold: Adjust the vertical hold only if the picture is rolling up or down the screen, Adjust for a centered picture by turmming the control to the middle of the stable range.

Horizontal Hold: If the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken into a series of diagonal lines, adjust the horizontal hold same as vertical hold.

Yoke: The yoke shovid never need adjustment unless the controls have been tampered with or the machine damaged. If yoke adjustment is necessary, adjust both ycke rings simultaneously for optimm centering of the image on the CRT. This adjustment is best handled by a qualified service person.

Five-Volt Supply: This is located on the power/audio PCB which is on the left side of the monitor behind the power transformer. There is a 1000-ohm trimpot to adjust the supply voltage. This measurement should be made on the logic PCB to allow for a voltage drop between monitor and PCB.

Regulator Adjustment: Connect monitor to AC line supply. Adjust horizontal and vertical controls wtil display is synced. Connect a precision voltmeter to any of the 73-volt test points and adjust regulator control R74 on PCB for an output of 73 volts. CAUTION: Do not run the regulator control through its range or you may damage the monitor. Only a slight turn is necessary for proper adjustment. Both the 5-voit and 73-volt adjustments have been made at the factory and under normal conditions should not need readjustment.

Page 8

1-8 AC Voltage Switch: Set this switch to the 115V position ("115" visible on the switch) if the machine is connected to a 115-volt source. Set it to the 230V position ("230" visible on the switch) if the machine is connected to a 230-volt source. The TV monitor

will not function if this switch is misadjusted. NOTE: If the monitor of a 230-volt machine is set to 115 volts, it will blow the machine line-fuse repeatedly.

TV Monitor Fuse: One 6/l0-amp, 250-volt fast-blow fuse protects the TV from electrical overload (for 155-volt operation, the TV fuse must be l-amp fast-blow). Replace blown fuses ONLY with those having the above rating. This fuse is located on the electronics mounting board inside the rear door. The fuse farthest from the door is the TV fuse, and the fuse nearest the door is the PCB fuse.

The PCB fuse should be replaced ONLY with a one-amp, slow-blow, 250-volt fuse.

CAUTION: Any work performed on monitor chassis should be done only by qualified service personnel who are familiar with servicing procedures and precautions.

GAME CIRCUIT BOARD ADJUSTMENTS

On Circuit Board 1 (on the left side of cabinet, as seen from its rear) there are three adjustments you may want to make:

A. Master volume: These adjustments are located in the upper right area of the board. There is a small tab on each of these pots. When these are set at the same point, the volume of both tanks will be equal.

Missile firing and explosion sound: These adjustments are located in the upper left area of the board. Again there are two pots to adjust. Setting the tabs evenly on the pots will set the volume evenly between the two tanks.

Page 9

c. Game time: There is only one switch located on Circuit Board 1; next to this switch is the pot that adjusts game time. This pot has been preset at the factory: switch in the 25¢ position, one game costs a quarter and will last 60 seconds. With the switch in the 50¢ position, one game costs two quarters and will last 120 seconds. You may set this switch as you wish and also adjust the time pot to your convenience.

Do not attempt to adjust any other pots located on these boards, as they are factory adjustments and tampering with them may have detrimental effects upon the game.

1-9 530 OOIN ACCEPTOR

All coin acceptors leave the factory adjusted for maximum performance. If, however, more critical adjustments are desired, or if the unit has been completely disassembled for service, the following adjustment procedure is suggested. If the coin acceptor has been removed from the machine, place it in a vertical position on a level surface. If the acceptor is still mounted on the coin door, place the coin door in a vertical position on a level surface. See exploded coin acceptor and mechanism drawings on pages 1-10.

A. Kicker and separator:

  • Set the acceptor with the back of the unit facing you in the test position.
  • Loosen the screws holding the kicker (1) and the separator (3) and move both the kicker (2) and the separator (4) as far to the right as they will go. Tighten the screws.
  • Insert several test coins (both old and new) and note that some are returned by striking the separator.
  • Loosen the separator screw and move the separator a slight amount to the left. Tighten the screw.
  • Insert the test coins again and, if some of them are still returned, repeat step (d) until all the coins are accepted. (£) Loosen the kicker screw and move the locker as far to the left as it will go. Tighten the screw.

1-7

Page 10
  • Insert the test coins and note that some are returned. (hn) Loosen the kicker screw and move the kicker a slight amount to the right. Tighten the screw.
  • Insert the coins again and, if some are still returned, repeat step (h) until all the coins are accepted. ;

(Jj) Be sure that both screws are tight after the adjustments have been made.

Magnet gate: .

  • Set the accer or with the front of the unit facing you in the test position.
  • Turn the magnet gate adjusting screw (2) out or counterclockwise until none of the coins will fit through.
  • With a coin resting in the acceptor, turn the adjuster in or clockwise until the coin barely passes through the magnet gate.
  • Test this adjustment using several other coins, both old and new, and if any of them fail to pass the magnet gate, repeat step (c) until all the coins are accepted.
  • Fix the magnet gate in this position with a drop of glue or Loctite , if necessary.

Acceptor maintenance: Depending on the environment in which the acceptor is used, periodic preventive maintenance should be performed. The mainplate (5) may be cleaned with any household cleaner. Thorough rinsing and drying are necesasry to remove deposits and/or film. Remove all metal particles from the magnet by guiding the point of a screwdriver or similar tool along the edges of the magnet. You will notice that

the particles will cling to the point of the tool. Remove the transfer cradle (9) and the undersize lever (10) and clean the bushings and the pivot pins. A pipe cleaner is an effective cleaning tool. Apply powdered graphite or pencil lead to the pivot pins and bushings and reassemble. Spray the entire unit lightly with wD-40®, a lubricant.

Page 11

1-10 GENERAL MACHINE MAINTENANCE

Due to its solid-state circuitry, your machine will require very little maintenance other than periodic cleaning, lubrication and TV monitor adjustment. The cabinet and plexiglass screen may be cleaned with any non-abrasive household cleaner. The coin acceptor and the rejector

linkage should be sprayed lightly once every three months with wo-40®

or a silicone lubricant. The potentiometer shafts mist never be lubricated in any way. The TV monitor is adjusted only when the CRT picture is distorted, or if the contrast or brightness appears to be out of adjustment.

1-9

Page 12

KICKER SCREW KICKER SEPARATOR SCREW SEPARATOR MAINPLATE ASSEMBLY GATE ASSEMBLY COVERPLATE ASSEMBLY RAIL CRADLE ASSEMBLY UNDERSIZE LEVER MAGNET GATE ASSEMBLY } MAGNET GATE ADJUSTER SCREW LOWER GATE PIVOT SPRING “> UPPER GATE PIVOT SPRING GATE PIVOT PIN 7 9

WIPER LEVER SPRING

WIPER LEVER

WIPER FIGURE D: COIN ACCEPTOR — EXPLODED

FIGURE C: COIN MECHANISM — EXPLODE

1-10

Page 13

Section 2

Service Information

2-1 TEST EQUIPMENT

In order to test any Atari PCB, some items such as the logic probe are absolutely essential. Others are desirable and will make the test procedure easier but are not absolutely essential. Some of these instruments are available from the Atari Customer Service Department and are: the Kurz-Kasch 520 Logic Probe, the Atari Video Probe, and the Hewlett-Packard 10529A Logic Probe. Other instruments that are very useful are the HP 10526T Logic Pulser and the Tektronix 465 Oscilloscope. These items are available through your local electronics supply house.

2-2 REQUIRED EQUIPMENT

The following items are essential to perform the test procedures presented in this manual:

A. Logic Probe: This instrument is designed for checking the outputs of integrated circuits. The Kurz-Kasch Logic Probe, Model Number LP-520, which is available through the Atari Custamer Service Department or most large electronics supply houses, is recommended. This logic probe indicates if a signal is a logic high, logic low, or changing from one state to another. Consult the operating instructions included with the probe for further details about its operation.

B. Video Probe: This probe is a very simple but extremely useful device and consists of two test clips, a length of rubber-coated, test lead wire, anda 4.7K watt carbon resistor. Video probes may be obtained from the Atari Customer Service Department, or, if necessary, they can be assembled from standard components available at all electronics supply houses.

Page 14

2-3 OPTIONAL EQUIPMENT

It is possible to find 90% of the possible PCB computer malfunctions without the following items. However, if a complete set of troubleshooting equipment is desired, Atari recommends the following:

A.

2-4 Hewlett-Packard 10529A Logic Comparator: This device is used to verify correct IC operation. It simply clips onto in-circuit ICs and instantly displays any logic state difference between the incircuit test IC and the reference IC in the comparator. Logic differences for each pin of a 14 or 16 dual in-line package are indicated by a lamp on the comparator. If the logic comparator is purchased from the Atari Customer Service Department, it is shipped with 20 pre-programmed reference PCBs. If the device is purchased elsewhere, these PCBs must be specially programmed.

Hewlett-Packard 10526T Logic Pulser: This device is used to stimulate in-circuit ICs so that they are driven to their opposite states. This device is available from the Atari Customer Service Department or can be obtained from most large electronics supply houses.

Tektronix 465 Oscilloscope: This oscilloscope is used for viewing various waveforms and should be ordered from Tektronix. Consult the manufacturer's operating instructions for details on oscilloscope operation.

REMOVAL AND REPLACEMENT PROCEDURES

Joystick controls: To gain access to joystick controls, open the top door and remove 10 screws holding joystick control covers to the top. Then remove 6 nuts and bolts holding joystick controls in table top. The joystick controls are now accessible for servicing.

2-2

Page 15

RT B. TV monitor: To remove monitor, open top door; have a second person hold up top and support the TV. Leave support bar hanging inside table. Remove the 12-pin Molex connector from rear of TV. Then carefully remove pair of nuts holding each of the two tie bars. TV can now be lowered from its frame in the table top.

Cc. Monitor power/audio PCB: To remove this board, locate it on left side of monitor behind power transformer. Carefully pull up on the poard. To replace this board, locate slot between pins 3 and 4. Keeping slot on your left side, insert board into edge connector.

D. Monitor main PCB: To remove this board use a screwdriver or similar

object and slowly pry the board up off the chassis at several places along the edge until it clears the pins. Then unplug socket from yoke and lift board up. ‘To replace this board, follow above steps in reverse order.

E. Game circuit boards 1 and 2: Each board is mounted to the cabinet by a screw located on each side. Remove edge connectors first, then remove the four screws. DO NOT TRY TO SEPARATE THE TWO BOARDS. ‘They must remain as one unit. After removing boards, carefully follow board shipping procedure (section 2-6) in order to minimize chances of damage. To replace the set of boards, follow above steps in reverse order.

2-5 TROUBLESHOOTING

The first step in any troubleshooting procedure is to observe the characteristics of the malfunction. With these clues in mind, examine the areas of the machine that might cause these symptoms. For example, if there is no power, check the harness — not the PCB. Likewise, if part of the playfield display is missing, check the PCB — not the harness or TV.

Three major areas of the game can be isolated for troubleshooting purposes: the TV, the PCB, and the harness. The harness includes the fuses, the transformer, the interlock switches, the AC line filter, the start and coin

Page 16

switches, the antenna wire, the potentiometers, all plug-in type connectors, the PCB edge connector, and all the interconnecting wires.

A. Substitution: Substitution of parts is a legitimate and easy way to troubleshoot the machine. For instance, if you suspect a PCB malfunction, try substituting another known-to-be-good PCB. To check the TV monitor by substitution, connect the malfunctioning game to a known-to-be-good monitor. Harnesses are checked by elimination. Substitute a good TV and PCB, and if the malfunction persists, the harness must be at fault.

Other troubleshooting tips: If you have only a TV raster* and you want to determine if the PCB or the TV is causing lack of video display, try the following test:

  • Disconnect the PCB edge connector;
  • Turn the brightness and contrast all the way up;
  • Touch video input to TV, pin 10 on PCB edge connector.

If your TV monitor is functioning correctly, you will see faint black bars or "hum bars" on the screen.

Troubleshooting by symptom:

  • No power: check for correct line voltage. If correct, check fuses and interlock switches. If these are alright, check transformer primary, which should show line voltage. Then check transformer secondary (pins 3 and 21) which should be 10 VAC with respect to ground. Also check to see if the interlock switch is on, either with the top door closed or with the switch defeated.
  • Game credit shuts off: try cutting the antenna wire shorter in increments of 1-2 inches.
  • Game credit shuts off and/or TV picture shrinks: check line voltage with VOM and be aware that a large motor nearby (such as an air conditioner) may drop line voltage when starting up.

#a TV paster is a black but lighted TV screen with the brightness turned all the way up.

Page 17
  • No picture or raster: check to see if TV connector is plugged in; check for line voltage at TV, and whether the latter's AC voltage switch is set to correct position. Check TV fuses and brightness control. If fuses are alright, check if the CRT's choke filament is glowing and if there are any loose wires.
  • TV raster only: check harness and especially the PCB edge connector. Check PCB, TV, and especially the 12-pin Molex connector on TV.
  • Picture rolls: adjust TV vertical hold. Check or replace PCB.
  • Picture is wavy: First check volt power supply on two game circuit boards. Do this by measuring between the two heavy traces on each board with voltmeter or oscilloscope. There should be 5 + % volts on each board. Next, locate pin 32 on large monitor circuit °* board. Measure voltage from this pin to ground. There should be 73 volts at this point. If voltage is either too high or too low, adjust 73-volt regulator pot located on same PCB in upper left-hand corner. DO NOT TURN THIS POT THROUGH THE WHOLE RANGE or you may damage it. Only a slight turn is necessary. In addition, you may need to adjust TV horizontal hold, replace transformer, and/or check harness (particularly grounds). th) Picture is broken into diagonal lines: adjust TV horizontal hold. Replace PCB.
  • Jerky tank motion: replace appropriate potentiometer.
  • No game credit: check coin mechanism and switch, and the harness. Replace PCB.
  • Game sequence incorrect or parts of playfield display missing, distorted or not functioning: replace PCB.
  • No audio: check volume control, speaker connections. Replace PCB.
  • White picture but no display: check edge connector on logic PCB, 5-volt supply from monitor, and 12-pin Molex connector on monitor.
  • Ne firing of shell or tank movement. Check joystick switches and harness connections. The joystick switches are simple on/off switches and may be checked with an ohmmeter or continuity tester.
Page 18

2-6 PCB_SHIPPING PROCEDURES

When packaging PCBs for shipment, make sure the top of each board is facing the other and that bubble wrap or foam rubber is between then. This interfacing must be thick enough to insure that parts of one board do not come in contact with the other board. DO NOT USE small pieces of styroform as packing material between the boards. Careful packing is recommended as Atari cannot be liable for items damaged in transit. Also, include a short statement describing the problem encountered with the game.

2-7 LOGIC TYPES AND FUNCTIONS

7400 Quad 2-input NAND gate 7402 Quad 2-input NOR gate 7404 Hex inverter

74SO4 Hex inverter

7408 Quad 2-input AND gate 7410 Triple 3-input NAND gate 7413 Dual NAND Schmitt trigger 7420 Dual 4-input NAND gate 7425 Dual. 4-input NOR with strobe 7427 Triple 3-input NOR gate 7430 Single 8-input NAND gate THR BCD-to-7 segment decoder 7450 Dual AND/OR gate (inverter/expander) 7474 Dual-D flip flop 7483 4-bit full adder

7486 Quad exclusive OR gate 7490 Decade counter

7492 Divide-by-12 counter 7493 4-bit binary counter 74107 Dual JK M/A flip flop T4153 Dual 4-bit multiplexer

2-6

Page 19

LOGIC TYPE

74157

74165

74192

74193

1M380

NESS5

NES66

RC4136D

MFC6040

8098

8103

8099

9311

9312

9314

9316

9321

9602

74186 FUNCTIONS

Quad 2-input data selector/multiplexer Parallel-load 8-bit shift register

Synchronous decade up/down counter

Synchronous binary up/down counter Amplifier Timer

Function generator

Dual operational amplifier Quad operational amplifier Voltage-controlled operational amplifier Hybrid

Hybrid

Hybrid One-of-sixteen decoder/ demultiplexer 8-input multiplexer

Quad latch

4-bit binary counter Dual one-of-four decoder

Dual monostable multivibrator

ROM

Page 20

Section 3

Schematics, Drawings and Parts Lists

Number Title

003860 Parts List, Top Assembly A003860 7 Top Assembly

003857 Parts List, Joystick Assembly A003857 Joystick Assembly

004032 Harness Schematic

003861 Parts List, Electronics Tray Assembly A003861 Electronics Tray Assembly

003110 Board I Schematic

003110 Parts List, Board I Assembly A003110 Board I Assembly

003112 Board II Schematic

003112 Parts List, Board II Assembly A003112 Board II Assembly

[none] Motorola XM$01/XM701 Monitor Schematic

Page 21

C.T. TANK ASSEMBLY TITLE TOP ASSEMBLY P/ L. 003860

PARTS LIST SPECIFICATION Page_|_of 2.

Drawn Checked Mech, Eng.

Proj. Eng. Elec, Eng REV. Innovative leisure

PRODREL sd Rev per ECN #1525

jiten [Part Number | aty.| DESCRIPTION

140038581Lower Cabinet Assembly
2A0038561Table Top Assembly
375-2112S6Screw, Mach., Rd. Hd., Cross-Recessed #10-24 x 3/4"Lq.
4002462aeT.V. Monitor Modification Detail
50036942Tie Bar
675-015S4Washer, Flat, Reg. Pattern, Steel, #%
775-0454Washer, Split-Lock, Cres., #5
875-91584Nut, Mach., Hex Hd., Standard Pattern, #4%-20
90038502Cover, Joystick
1082-160820Screw, Flat Head, #6 x " Lg.
11A0031101P.C. Assembly, Panzer Board #1
12A003112LlP.C. Assembly, Panzer Board #2
130011412Foam Pad
1472-66084Screw, S.M. Pan Hd #6 x % Lg.
150040101 | Cash Door, Plex, 50¢
Page 22

SECTION ' B- B"

Page 23

c.T. TANK nF BLY TTPL JOYSTICK ASSEMBLY P/L 003857

Drawn. PARTS LIST SPECTFICATION Page 1 of 1 + Checked [Mech Eng. Proj. Eng.

Rev. Innovative Elec. Eng REV, leisure

Description i Date Description

Part Number DESCRIPTION

003851 003849 A002303-05 A002303-04 BwWN BREE Panel, Support Plate, Mounting, Joystick Joystick Assembly with Button Joystick Assembly without Button

Page 24

i

Page 25

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 26

COIN 2-NC}it STE COIN 2-NON2 FCCIN | -NC}IS

  • 25¢ itty lan LAMP

iN400! BN RL DIODE Coin == |Counter

faozt How 8 [CONNEC TOK |i? | TANK x 0-4 268 “ aay eo POWER HCV J6CHZ s ge bod TV COUNEST

Page 27

[UCTS TICKS, a GOAN Tp. WIGN

YONGE BUT ION: SA Sa OT BUT

(NTHRPRET THs DRAMING DRAWN ny mre PER UNAAI YI4s ATARI INCORPORATED 14600 Wanchester Bowlevaed ‘UNLESS OTHERWISE SPECIFIED Los Gatos. California 95020 a

[ wcnerconna, | HARNESS, SCHEMATIC.

Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

C.T. TANK A.

ATARI

Innovative leisure ELECTRONICS TRAY ASSEMBLY

PARTS LIST SPECIFICATION Page 1 of 1 Drawn Checked Mech, Eng. Proj. Eng. Elec. Eng

Part Number | Qty.| DESCRIPTION

10038591 | Electronics Tray
20040271 | Main Harness
3A003560-1L Transformer Assembly
40042441 | Power Cord Assy
546-2022011 Fuse, 2 AMP, 125V
6A0034601 | AC Power Harness
790-30011 | Filter, Power Line
878-250022 Screw Down Tie Wrap
972-66089 | Screw, SM, Pan Hd, Phil, #6 x & Lg
1072-68244 Screw, SM, Pan Hd, Phil, #8 x 14 Lg
Page 30

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 31

B T REVISED PERECN 1Ge7 43

ATARI INCORPORATED 14600 Winchester Boulevard Los Gatos, California 95030

ON: FRACTIONS = a1/16 x= 4.1 ANGLES =419 xx = 4.03

Page 32

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 33

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 34

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 35

Tk y2lo

aos

q oS lev is) -ev

NOTICE £0 ALL PERSONS RECEIVING Tras DRAM: oa aes iene

apy soe iat ena tts SELaea Tp ofthe ute! ate et tien Sept tet Ne pn a 32 poe Morar @ Wee eam 2107 Boom Bae e108 = Wet —_ BK

Lt e100 Ms

VoLuMe 2 ion +1ev

HEV 108. INITIALS and DATE

24,87, 1a, Mt e105 33 AvBIo OUT 1 +) {t 17 SOD zy

pe

cio5 rey £

ALBIS ODT 2 82 SPEAKER.

m SCHEMATIC, TANK BOARD TL

OBO cs

ATARL INCORPORATED "600 Winchester Boulevard Los Gstos, California 95030

‘a

Page 36

TANK 4 IN ASSEMBLY TI TANK - BOARD 1 P/Loosiio PARTS LIST SPECIFICATION Page _1_of 2

Drawn ATARI] |; [= Innovative Proj. Eng. REV, leisure H

Description Rate [ rev. | APP ea 11-22 (Osman neorporates ECN 74-120 11-26) neorporates ECN 74-Tpy 12-Thg

Part Number DESCRIPTION

1 37-7400 2 Integrated Circuit, 7400 2 37-7402 6 " u 7402 3 37-7404 4 " 7 7404 4 37-74HO4 1 = . 74HO4 5 37-7408 2 " " 7408 6 37-74HO8 1 " ” 74HO8 7 37-7410 2 " 7 7410 8 37-7420 2 = 7 7420 9 37-74S20 2 " " 74820 10 37-7474 il " w 7474 ii 37-7486 3 " " 7486 12 37-74107 5 - " 74107 13 37-74165 4 " = 74165 14 37-9316 20 " " 9316 15 37-555 1 " . 555 16 37-741. 2 " = T4H1 17 37-LM380 2 i " 1LM380 18 37-MFC6040 2 " " MFC 6040 19 37-LM309 ak IM 309 K, Voltage Regulator 20 10-5101 1 Resistor, Carbon, 5%, % Watt, 100 ohm yan 10-5102 10 " 7 " " 1K ohn 22 10-5103 2 " " " " 10K ohm 23 10-5104 3 " ad a " 100K ohn 24 10-5105 3 u a " " 1Meg ohm 25 10-5221 1 " " % " 220 ohm 26 10-5225 1 " " ™ 7 2.2M ohm 27 10-5333 6 7 w " " 33K ohm 28 10-5472 3 " v " " 4.7K ohm

30 10-5474 1 " " " 470K ohm 31 10-5561 1 " " " " 560 ohm

34 10-5684 2 " v . i 680K ohm 35 10-5820 1 7 " " " 82 ohm

37 10-5334 1 " " m" 330K ohn 38 14-2472 2 " Ls 2% " 4.7K ohm 39 11-5271 2 Resistor, Carbon, 5%, % Watt, 270 ohm

Page 37

ASSEMBLY TITLE TANK - BOARD 1 P/L oce3)110

PARTS LIST SPECIFICATION

Part _Number DESCRIPTION

13-5P22 19-808W4PO 31-1N914 31-1N4001 32~1N5229 31-MR501 3U-2N3643 33-2N3644 34-2N5190 34-2N5193 34-MJE200 19-311503 19-311103 19-311105 27-120104 27-101102 24250105 24-250505 24-160107 24060257 24-250478 2u-200808 28-101221 29-001 69-001 78-06002 WY, Resistor, Carbon, 5%, % Watt, .22 ohm Resistor, Wirewound, 20%, 10 Watt, 4 ohm Diodes, 1N 914 Diodes, 1N 4001 Diodes, Zener, 1N 5229B, ve 3V, 5%, Motorola Diodes, MR 501 Transistor, 2N 3643 Transistor, 2N 3644 Transistor, 2N 5190 Transistor, 2N 5193 Transistor, MJE 200 Trimpot, 50K Trimpot, 10K Trimpot, 1 Meg Capacitor, Ceramic Disc Bypass, .1 uf "001 uf Electrolytic, 1 uf, 25v 5 uf, 25V 100 af, 16V 250 uf, BV 4700 uf, 25V 8000 uf, 16V Dipped Mica, 220 pf Tantalum, 100 uf, 10V Switch, DPDT Heatsink, Thermalloy #6111B-66 HEATSINK, THERMALLON #GOIB Serew, Mach: ‘ine, » Pan Hd., Phil., 6-32 x 5/8" 75-056 Washer, Lock, Internal Star, #6 75-9168 Nut, Machine, Hex, 6-32 72-14128 2 Serew, Machine, > Pan Hd., Phil., 4-40 x 3/4 Washer, Split Lock, #4 Nut, Hex, 4-40 Printed€ireuit Board, #90124 Resistor, Carbon, 5%, %W, 180K ohm Capacitor, Ceramic Disc, .01 uf Capacitor, Electrolytic, 500uf, 25V REsistOR , CARBON La Bee AW , B.3K OHM Diode, G. E. Type Al! H NYP PREP RP BEN WOYOEPNNEPHEE EF ONEPN OEP

72-16108

Nn

75-044 75-914S OCcaill 10-5184 27-101103 24-250507 10-5332 31-ALUF FO wPNENN

Page 38

B . Dee bn

Page 39

DESCRIPTION pete [PBT

4" ASSEMBLY TANK BD. T

Page 40

PUNFIELD select i 256N- CRF

  • v3

NOWTEK (28-Pn) rom= HID

4a Gn at SUPER

afAays | _} toa

rs FiLD —3 sy MINE. NAT RIV- ONE [Go| MINEFIELD VINES —H FLASH

NOME FIELD sity

rep wT K1—— exif 22) es

ana—|

G20 cis

aa, You 250 yy }-—@)vineo our a

Page 41

BEscE eres a [@ [Rev Pen eeu wer

i3]] moTORY

MOTOR 7.

ShOT COM

MW J] vo

ou Ry NAL [apjvez Gdver HL 1OY Q ag awww

eer aw S3u

eze 250.5 que,

KEE GAMES, INC. 330 MATHEW ST, SANTA CLARA, CALIE. 93030 (4081 249-4090

Page 42

14,316 MMe 2568 — , UI "8

2H HBLANK

# fuser stink et ano ma JS. Bi 219 ACpUNT a os BIE af Saar = i EIS

#2 LEFT STO

ATTRACT

__ ie aly Wok STR e aN BE HLUNFO veo oe i. 12, 0, ov asl |

, SCORE LAP ABY, LORD 8, Le INFO ~~

2 ay oat 2568 4 “hs 8

Vinro

Page 43

BOUNCE T ATTRACT

BLO-UP2 er ee sriig—4 8 By NO. sToPL

vior ase fe he HITZ — N.O. 5. otal, i a SOUMET aha ae tess te 10) &¢ 8 ——

BOUNCE 2.

ATTRACT

ter eer aTicK | pow Je

NOTE: PLANER #1 13 On THE RIGHT SIDE. (WHITE) PUNER #2. 13 OW THE Leer Soe Cecqcr )

eeounces * BYERS 10 amr] 3588

4 wITZ, 5s pS ee an suet: 22 PLAY FIELD gy Tay NWF egy Son if 100,

he[=on
FIRE)= 4:‘
etFRE:4iole

Fo yankz 4 BOUNCE TANK

pe»

Tm

Di

*g Ho 8820

Ae,

ND.

BLO-UPI

PLAYFIELO

DY BOUNcE?. , . 200 Es 7

BuLNCEL

‘BOUNCEZ

Kee GAMES, INC 330 MATHEW sr SANTA CLARA. CAUF. 98080 (408) 24-6090

sare Th JUN TE, SYNC, TIMING € CONTROL CIRCUITS PAGE 2 OF 2 OOSNIZ

Page 44

ASSEMBLY TITLE TANK = BOARD 2 OOSIIe

PARTS LIST SPECIFICATION

Drawn Checked Mech. Eng.

Proj. Eng. Elec. Eng Po S [oote [oe [11-22 | Innovative leisure

Description PROU RE

Kf eee eon \Oaq Wake [LG [Per Eon 1482 a rs

DESCRIPTION

1 Integrated Circuit, 7400 2 37-7402 11 7402 3 37-7404 4 " " 7404 4 37-74HO4 1 id " T4HHOW 5 37-7406 3 * 7 7406 6 37-7408 4 . " 7408 7 37-7410 6 " " 7410 8 37-7420 2 " " 7420 9 37-7427 1 " 7 7427 10 37-7474 16 : 7474 11 37-7486 2 ut " 7486 12 37-7492 1 " " 7492 13 37-7493 7 " " 7493 14 37-74107 3 " " 74107 15 37-74153 5 7 " 74153 16 37-74165 1 " " 74165 17 90-2006 1 16K Tank Rom E.A. #4800SD 18 37-74193 2 Integrated Circuit, 74193 19 37-8277 1 8277 20 37-9316 4 " 9316 21 37-9321 1 " w 9321 22 37-9322 4 bi " 9322 23 37-9602 3 " » 9602 24 37-555 2 " : 555 25 37-556 1 " e 556 26 37-566 2 a " 566 27 37-MFC6040 2 " " MFC 6040 28 10-5101 10 Resistor, Carbon, 5%, % Watt, 100 ohm 29 10-5102 12 " " " 1K ohm 30 10-5103 3 " " " " 10K ohm 31 10-5104 4 . * " " 100K ohm 32 10-5221 1 7 i " ” 220 ohm 33 10-5223 2 " “ " . 22K ohm 34 10-5331 2 " " - m 330 ohm 35 10-5333 3 u " " " 33K = ohm 36 10-5334 2 " " " " 330K ohm 37 10-5392 2 " " " " 3.9K ohm 10-5471 6 470

Page 45

ASSEMBLY TITLE TANK - BOARD 2 P/L 203112

10-5472 10-5473 10-5561 10-5681 10-5682 10-5820 10-5184 10-5185 13-5P22 19-808W4PO 31-1N914 32-1N5229 34-2N3643 33-2N3644 34-MJE200 19-311103 19-311503 90-101 27-120104 27-101103 27-250105 28-101101 29-004 29-003 29-001 21-101224 24-250505 24=-250106 24-060257 24-200808 79-4242 78-06002 55-6125 72-14128

75-044 75-914S 603113 10-5684 19811104 21-101104 RE EN PONE RENN @ Ete

NRE RP PRP RP WONNNNNWON

HNNNENN PARTS LIST SPECIFICATION

Item | Part Number

=

ow DESCRIPTION.

% Watt, 4.7K ohm 47K ohm 560 ohm 680 ohm 6.8K ohm

""""82 ohm

180K ohm 1.8M ohm 2 Watt, .22 ohm Wirewound, 20%, 1OW, 4 ohm Diode, 1N 914 Diode, Zener, 1N 5229B, 4.3V, 5%, Motorola Transistor, 2N 3643 Transistor, 2N 3644 Transistor, MJE 200 Trimpot, 10K Trimpot, 50K Crystal, 14.31818 mhz Capacitor, Ceramic Dise Bypass, "(01 uf

"""(901 uf

" Dipped Mica, 100 pf ™ Tantalum, 1 uf, 6V

”i22 uf, 6V

100 uf, 10V Mylar, .22 uf v Electrolytic, 5 uf, 25V u 10 uf, 25V

=7250 uf, 6V

8000 uf > i6V Resistor, Carbon, 5%, " "

1 " "

-lo uf

" w

" "

Socket, 24 pin Heatsink, Thermalloy #6111B-66 Flex Strip Jumper, 25 Conductor, Ansley #FSN-23A Serew, Machine, > Pan Hd., Phil., 4-40 x 3/4" Washer, Split Lock, #4 Nut, Hex 4-40 Printed Circuit Board, #90125 Resistor, Carbon, 5%, %W, 680K ohm Trimpot, 100K ohm Capacitor, Mylar Jumper, (30 AWG, «lo uf Insulated)

Page 46

[ALUTEELETT UEC

AM OPTIONAL JUMPER:

NOTES:

GT ovis

Page 47

(| Tag MNVL ATGW3ASSY vu case minroron OWL Puespog JaneDUIM COREL ‘GRLYWOaHOONL PAVEY nt Sma Bebop wad azal o Leo oe asa faa] Ss Sos \2IS3S wus

Page 48

ANT ou Schematic, Motorola XM501/XM701 Monitor

Page 49

JONNOW LOLWX/LOSWX B102010Wy “>eUWIAYIg ype eye 9 0.

calla

Wo1274N09 790225,

sono 1

Page 50

eerie gee ee eee ee

free from defects in material and workmanship under normal use and

service for a period of ninety (90) days from date of shipment. Seller

warrants that its television monitors are free from defects in material xs

and workmanship normal use and service for a period of thirty or parts thereof are warranted

GO) age Seaeate OE chine. None of the Seller's other products or parts thereof are warranted.

peek As or credit Buyer’ fepace, on ote Buyer's acoutt fr sich provided:

  • gas is promptly notified in writing upon dis-

covery by Buyer that said products are defective;

  • Such products are returned prepaid to Seller's

(ce) Seller's examination of said products discloses action that such alleged defects existed and were Mating? Se improper repair,

Desens Aa hcg nee comin coat ere erin Seen Retin Atari, Inc. This document is loaned under confidential custody for the sole puree ee ee ee eee not be used by or disclosed to any person for any other purpose what- ‘ever, and remains the property of Atari, Inc. Neither it nor the information it contains may be reproduced, used, or disclosed to persons not ees ee eae ee re te et ee eee ae