CATHODE RAY TOMES

Indoor Soccer

Indoor Soccer (set 1) (Universal, 1985) · Document · 18 pages · 11 sections · original scan

Page 1

“WSdaAINe TIWANVIN SDIAUSS YAIIOS * YOOdNI

Page 2

UXIVERSA

UNIVERSAL U.S.A., INC. INTRODUCES

INDOOR SOCCER

Indoor Soccer is manufactured and marketed as a conversion for coin-operated video games. This manual is designed for the use, maintenance and installation of this product.

Installation, maintenance or repair should only be attempted by qualified service personnel.

Technical assistance is available by calling:

1-800-538-7568 Outside California.

1-408-727-4591 Inside California.

172247 Telex.

Page 3

Upon receipt of your Universal U.S.A. conversion kit, be sure to verify that all contents are complete and free from defects or damage. Notify your distributor of any discrepancies in the kit as soon as possible.

Your Indoor Soccer Conversion Kit includes:

A) 1 - Indoor Soccer P.C.B. (Contained in R.F. shield). UNIVERSAL PART #02-10027-00 (06-10100-00).

B) 1 - Audio-amplifier P.C.B. UNIVERSAL PART #02-10100-00.

©) 1- Main wiring harness assembly. UNIVERSAL PART #03-10127-00.

D) 4- WICO/8-way batt handle joystick assembly. UNIVERSAL PART #04-05000-00.

E) 2- Push buttons (Complete with housing). UNIVERSAL PART #04-0511 1-00 04-05202-00.

F) 1-24” x 9” clear control panel plexiglass. UNIVERSAL PART #05-00005-00.

G) 1 - Set of control pane! decals. UNVIERSAL PART #05-27107-00.

H) 1 - Polycarbonate control panel overlay. UNIVERSAL PART #05-27105-00.

  • 1 - Indoor Soccer Marquis (Title) decal. UNIVERSAL PART #05-27000-00.

J) 2- Indoor Soccer side decals. UNIVERSAL PART #05-27120-00.

K) 1 - Indoor Soccer instruction decal. UNIVERSAL PART #05-27110-00.

L) 1 - Indoor Soccer license sticker.

Page 4

Cabinet Requirements

The Indoor Soccer Conversion Kit can be installed into any standard cabinet (upright or cocktail). The game is designed to display on any standard horizontally mounted, color (R.G.B.), rastorscan monitor.

Many cabinets allow for the repositioning of monitors from vertical mounted monitor to horizontal mountings. Repositioning of a vertical mounted monitor is a delicate, if not cumbersome, operation and extreme care should be exercised in handling any monitor. It is recommended that the installation of the Indoor Soccer Conversion Kit be attempted only on those cabinets in which monitors are presently mounted horizontally or in such ca binets, where design facilitates the repositioning or mounting of monitors to be easily interchangeable. It is not recommended that cabinets be physically altered or any reconstruction of cabinets be done by anyone other than those qualified and having the appropriate facilities to conduct such oprations.

The Indoor Soccer P.C.B. will require regulated voltages of +5 and +12 VDC. Most standard power supplies will provide these voltages, therefore the replacement of existing power supply may not be necessary. Along with the monitor and power supply, the control panel, speaker, and coin door need to be retained from the existing cabinet.

Control Panel Installation

Parts furnished with the Indoor Soccer conversion kit for the control panel modification are pictures and listed on pages 8 and 9, as well as an installation layout.

Begin removing the existing controls and graphics, then prepare the surface by cleaning and removing any foreign material and debris. Take note of the existing holes in the panel to determine placement of the new controls.

NOTE: Repositioning and drilling holes to install the new controls on the existing control panel may be necessary and require the use of power tools. In the event that such tools are needed, exercise extreme caution. If assistance is required, contact a local Universal U.S.A. distributor.

Apply the polycarbonite overlay to the top of the control panel and trim away any excess material around the edges and holes to be used for the new controls. Attach the indication decals (i.e., joysticks, 1 player, and 2 player) on top of the overlay next to the corresponding holes. A

If needed or desired, measure and cut the clear plexiglass furnished with the kit to fit the existing control panel. Drill holes for the controls at 14 inches in diameter to accomodate the joystick and buttons where needed. Be sure to file or sand away any rough corners around the edges of the plexiglass.

-iii-

Page 5

Wiring Installation

All wiring terminations and connections for the Indoor Soccer conversion kit are in the secondary or low voltage circuit (less than 42 VDC).

Electrical cautions:

© Never attempt installation, connection or electrical terminations with power applied to the unit.

© Never disconnect the Printed Circuit Board(s) with power applied.

© Never replace any components with anything other than exact replacement parts.

Begin the wiring process by removing the existing P.C.B.(s) and wiring harness(es). Physically secure the Indoor Soccer P.C.B. and audio amplifier P.C.B. to the inside of the cabinet. Pin assignment and termination points of the harness assembly are provided on page 6 of the manual.

Termination of the wiring harness can be separated into five (5) basic categories:

Power Inputs: +5 VDC, +12 VDC and Ground;

  • Video Outputs: Red, Green, Blue, Video Ground and Sync;
  • Player Controls: Up, Down, Left, Right, Kick, Ist and 2nd Player Start;
  • Coin Door: Left Coin, Right Coin, Slam Switch and +5 VDC (Coin Meter);
  • Audio Output: Speaker.
  • Power Inputs: Termination of the voltage leads is probably the most critical and fundamental process of the installation. Extreme caution should be taken to insure corect terminations and proper voltages. The voltage input lines are distinguishable, as 18 gauge wire is used for each. (+5 VDC-Orange at pin #3, +12 VDC-Red at pin #8, and Ground- Black at pin #1). Before proceeding, verify that each input voltage is correct and at the proper designated pin assignment of the P.C.B. connector.
  • Video Outputs: Connections can be made by terminating the Red (Pin Z), Green (Pin A), Blue (Pin B) and Video Ground (Pin E) to the corresponding inputs of the monitor. To connect the sync output(s), first determine what inputs are needed by the monitor. The composit sync (White wire at Pin C), can be terminated to the composit sync input of the monitor, if applicable. Indoor Soccer will generate a negative composit sync. In most cases where negative horizontal and vertical sync is needed, terminations can be made by connecting the White composit sync line to both negative H & V inputs of the monitor.
Page 6

If a positive signal is needed, contact your local distributor to obtain a Universal 8300-TV-B Video P.C.B. (This assembly can be used to modify sync signals).

NOTE: The wires at pins #5 (Orange) and #6 (Brown) are designated for vertical and horizontal outputs and are needed only for supplemental modifications.

If the display appears on the screen “Upside-Down” the display can be turned by a dipswitch setting. (Dip-switch A-SW5—See option settings on page 2).

  • Player Control Inputs: Player control inputs will be connected at the control panel.

The joystick terminations can be made by connecting the designated wires to corresponding switches on the 8-way joystick supplied in the kit. The wires for each joystick are all color coded as to the function of each switch as follows:

UP - Blue DOWN - Yellow LEFT - Purple RIGHT - Brown KICK - Red GROUND - Black

1 PLAYER - Orange wire at pin #21 2 PLAYER - Green wire at pin Y

1 PLAYER JOYSTICK - A & B 2 PLAYER JOYSTICK -C & D

  • Coin Door & Inputs: Wiring for the coin inputs can be accomplished by following either of the diagrams on the bottom of page 6. Separate inputs are provided on pins #24 and #25 to allow for the selection of independent coin chute pricing. (For options on price selection, see page 2—dip-switch B).
  • Audio Outputs: Begin by soldering the speak~ ‘nes to terminals SI (-) and $2 (+) on the audio amplifier P.C.B., then connect the audio lug on the harness assembly (White 4pin molex) into the socket (p1-4) on the amplifier unit.
NOTE: To avoid audio distortion, verify that the voltage to the amplifier is regulated at +12 Volts DC. ’

“Ve

Page 7

F.C.C. Compliance:

THIS EQUIPMENT GENERATES AND USES RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED PROPERLY, LE., IN STRICT ACCORDANCE WITH THE INSTRUCTIONS MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. IT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A COMPUTING DEVICE PURSUANT TO SUBPART J OF PART 15 OF F.C.C. RULES, WHICH ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST SUCH INTERFERENCE WHEN OPERATED IN A COMMERCIAL ENVIRONMENT.

OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE INTERFERENCE IN WHICH CASE THE USER, AT HIS OWN EXPENSE, WILL BE REQUIRED TO TAKE WHATEVER MEASURES MAY BE REQUIRED TO CORRECT THE INTERFERENCE.

Indoor Soccer P.C.B. is enclosed in a metal R.F. shield to meet the F.C.C. requirements stated above.

To comply with the ruling, it is imparative that the R.F. shield is installed properly. After mounting, make sure that the cage is grounded, With an Ohm meter, conduct a continuaty test between the shield and the ground to verify proper installation. Enclosed in the conversion kit is an F.C.C. Warning Sticker. This decal MUST be placed and maintained on the exterior of the cabinet.

Under NO circumstances should this equipment be operated without the Printed Circuit Board properly installed in the R.F. shielding.

Page 8

I. HOW TO PLAY

@ One Player vs. Computer

e@ Two Player — Two vs. Two (player vs. player)

e Each joystick controls a corresponding character on the field

e To ’KICK” the ball, push the button on top of the joystick when the character controls the ball

e To "SLIDE”, push the button on top of the joystick when the character does not have the ball.

@ Use the wall(s) to bank kick

¢ Block opposing players by "body checking” or sliding.

Page 9

UNIVERSAL

IL. VARIOUS OPTIONAL SETTINGS DESCRIPTIONS OF DIP SWITCHES

¢ Dip Switch A

@Actual Time of Game (SW1 & SW2)e@One Player vs. Computer (SW6)

(Indicator always shows 3:00 and counts down) {Additional time extended for winning score)

1. 3:00 min.OFF | OFFContinuity
2. 2:30 min.OFFON
3, 2:00 min.‘ONOFF
4, 1:00 min.ONON

e

@ Game Continuation for 1 Player (SW3) Time Extension ‘sw3 YES OFF NO. ON | (The player may play same game with additional credit) _ @ Factory Settings

@Game Continuation for 2 Players (SW4)© Positions of Dip Switches
Time Extension4—_——

ves MAIN CIRCUIT BOARD NO. (Continuation of a two player game with additional credit)

eDirection of Screen (SW5)ON

Direction swW5

NormalOFFom

Reverse ON

© Dip Switch B (Coin & Credit)

©. Creal Left-side chute Right-side chute Standard and Custom Price Settings

in it

°reditSai_|sw2 | swa | swa | sws | swe | sw7 | swe.|
elt1 [| orF | orF | orF | orF | oFF | OFF | OFF | OFFThe game price set by a combina-
1_{_2[orr[ore | ofr | on | OFF | orF | oF [ ONtion of dip SWs is displayed on the
73|orr | orr | on | orr | ore | ofr | ON | OFFmonitor when coin credit is 0.
14_[orf | ofr | ON | ON | orF | ofr | ON | ON.A
15[ore | on | ofr | ore | ort | on | OFF | OFFa) When the settings for right
16 | orr | on | OFF | ON | OFF | ON | OFF | ONand left chutes are the same,
2_[_1[ore | oN | On | OFF | orr [ ON | on | oFF1 coin — 1 credit”, “2 coins
23|orr | on | ON | ON | OFF | ON | ON | ON— 3 credits”, etc. are dis-
31ON | ofr | OFF | OFF | ON | OFF | OFF | OFFplayed.
32[ON | OFF | OFF | ON [| ON | OFF | OFF | ON..
47on | orF | on | OFF | ON | OFF | ON | OFFb) When the settings for right
A7ontorr | on}on | on | ofr | on | ONand left chutes are provided
1+{on | on | ore | ore | on | ON | OFF | OFFdifferently, their respective
11on | on | orF | on | ON | ON | OFF | ONcontents can be displayed.
17[on | on | on | Orr | on | ON | ON | OFF

Freeplay | ON | ON | ON | ON | ON | ON | ON | ON

Page 10

UNIVERSAL

II. MAIN CIRCUIT BOARD IC LOCATION AND PARTS LIST

fe cee

eee wae pCa g (3 1 Gee

at I -U SG ame ——o-—n— universal“

Fig. 1 Main Circuit Board IC Location

Page 11
  • INTEGRATED CIRCUITS URIVERSAL
  • CAPACITORS
Item No. QiDescription+ Ratingay [ Description
7ALS 002SOP2
7ALS 0111034
TALS 04110430
TALS 0822211
TALS 202 [3913
T4LS 27147 = F25V1
TALS 92210 FIeV2
T4LS 746470 FI6V2
TALS 86é20P2
74LS138328P10

7ALS139 3

74LS1576(3) CRYSTAL
74LS1613[( Rating ‘ty.Description
TAL SoA,2_| [Goo mz1
7ALS245i9.828 MHz1

74LS257 4

HAUSZTS7(4) RESISTORS
Lea[ RatingatyDescription
74LS3731 |Va:
7ALS3744o7
74LS3741100i
M3241=3
76489N1aoa
NESS613903
HD465055P1=A
CF 372011a:
TMS1025N21C 2a"a a
TMS4164-15 16aka
Z80A3an;
MB8128-101Fac
MB8128-155Pi5
828147271

120 4

271282ai2
2725641028=
1001710382

DIPSP. 2

7805 1 1 This drawing provides standard information. Universal reserves the right to change without notice.

Page 12

URIVERSA

IV. SUB-CIRCUIT BOARD IC LOCATION AND PARTS LIST

846I-SUB = RI ig 4h we OR? CNT | om 15 }} cng +) sos] ft as as 4 ICE em Rs c2 27128 Reg wet 2S a» ICT 17504),

27128

  • INTEGRATED CIRCUITS is +t + ns Ico babe =a8 wo Re cé joe] 3s wy ie z e
  • RESISTORS
[tem No.tyDescriptionRatingayy.Description
MSM4013110K9
MSM401913K1
MsM402512201
Msm4o4011K1
MSM4520147K1
MSM4556 [ 1[470K1

MSM5205 1

HA179044| (4) CAPACITORS.

Rating Qty Description

(2) CAPACITORS47 FieV1
RatingQtyDescription47_F25V1
28P4680PF1
102511531

228 1 { 100PF 1 22PF 1

Page 13

UNIVERSAL

Fig-1

SOLDER SIDE

USE COLOR COLOR

2nd PLAY! Bik. ER ---—Gnn ---- Bik.

COIN SW [gous “| 1 eno. | ef 2 | Bik. ! Ora. Hi i Ora.

2nd PLAYER:

  • RIGHT (0) Brn. =| 1st PLAYER RIGHT @) 8M

Me Le Red

Or/ Pur

1 Or Gen Pins (E) (23) SLAM SW Grn.

2nd PLAYER UP (Cc)Blue|_PBlue

R | 14

ond PLAYER2nd PLAYER KICK (D)RedRed
JOYSTICK G2nd PLAYER RIGHT (c)Brn. | S_|18 | arn

2nd PLAYER DOWN (D) Yel. | 7 | 6 | Yel.

2nd PLAYER DOWN (c)Yel.|_U_|17,Yel.
2nd PLAYER LEFT (0)Pur.|_V_|18Pur.

2nd PLAYER LEFT (c) Pur. | W | 19 | Pur.

2nd PLAYER2nd PLAYER UP (D)Blue|X | 20Blue
SONSTICK D.2nd PLAYER START = Gm.|_Y_|21 | Ora,

VIDEO RED Red | 2 | 22 | Red

TOVIDEO GREENcm}a | 23 | Red

MONITOR VIDEO BLUE Gray

COMP. SYNC Wht.

Bik.

Bik.

NOTE:

CONNECTION FOR USE WITH COIN METER

R COIN SW

GND (PIN #8)

CONNECT EITHER PIN #24 OR 425 +5v «PIN #4) COMPONENT SIDE

GND (TO POWER SUPPLY)

GND (1st PLAYER & SELECT SW)

+5v (TO POWER SUPPLY)

+6v (COIN COUNTER)

+12 VDC

‘ist PLAYER UP (A)

‘1st PLAYER KICK (B)

1st PLAYER RIGHT (A)

1st PLAYER DOWN (8).

‘1st PLAYER DOWN (A)

ist PLAYER LEFT (B)

1st PLAYER LEFT (A)

1st PLAYER UP (B) 1st PLAYER JOYSTICK A

Ist PLAYER START

ist PLAYER KICK (A)

2nd PLAYER KICK (C)

COIN LEFT

COIN RIGHT 1st PLAYER JOYSTICK B

Pin (F)

GND

GND

CONNECTION FOR USE WITHOUT COIN METER

R COIN SW

Ne

EITHER, PIN #24 OR #25 +5v (PIN# 4)

GND (PIN#B)

NO

LOIN SW

Page 14

INSTALLATION INSTRUCTIONS

WICO 8-WAY JOYSTICK WITH FIREBUTTON

Wico No. 15-9681-01

Refer to Figures 1 & 2 before starting

2. Unplug the power supply cord to the game.

Disconnect the wiring to the original joystick assembly and remove the joy stick assembly from the game.

. Place the 2” washer (furnished with this kit) on top of the new joystick assembly mounting plate directly over the center hole.

. Mount the replacement joystick assembly to the game.

. Remove the joystick handle, switch actuator, large compression spring, and Eting from the bag of parts. Insert the joy stick handle through the control panel and joystick assembly. From the inside of the panel, push the spring and switch actuator over the joystick handle shaft and secure with the E-ring.

. Take the firebutton, small compression spring, firebutton switch actuator and firebutton switch assembly from the bag of parts. Insert the small compression spring over the firebutton shaft. Insert the firebutton and spring through the hole in the top of the joystick handle. From the inside of the panel, press the firebutton switch actuator over the serrations on the end of the firebutton shaft.

  • Take the firebutton switch assembly and clamp it over the joystick switch holder shown in figures 1 & 2.
  • Connect the wiring to the new joystick.
  • Connect the game power supply cord to an outlet.

For replacement parts call

Universal U.S.A., Inc. 1-800-538-7548

or

Wilco Corporation 1-800-323-4258

Page 15

i (-— FIREBUTTON

FIGURE 2

"KICK" BUTTON ACTUATOR

COMPRESSION SPRING (SMALL)

HANDLE

2” WASHER ——_--—_-— 2)

a) we —Nemen SPRING (LARGE) SWITCH ACUATOR ot E-RING ACTUATOR - FIREBUTTON SWITCH ‘SWITCH ASS’Y - FIREBUTTON

FIGURE 1

Page 16

Clear Plex INDOOR

Polycarbonite Overlay

Indication Decals C C

8-Way Joystick (4 each) SO ER

Buttons (2 each)

Pal Nuts (2 each)

2 vs. 2

Button Housings w/Leaf Switch (2 each) OPERATION PANEL

raat HOON JOYSTICK A JOYSTICK B JOYSTICK C JOYSTICK D

PUSH PUSH PUSH

©) ©): PLAYER 2P ; = 2 PLAYERS Hy 7

ISH ff i Ss Mi

Page 17

URIVERS

SOUND AMPLIFIER DIAGRAM AND PARTS LOCATION Fig-4

aPquITEH P4 P3 P2 PI

479. )R R4

  • log : cw 51K 25v vRi R3 1K 10K

vAi: RV 16YP 10S B 1KQ

SCUND AMPLIFIER UNIT

Page 18

Head Office Universal Co., Ltd. 1-7-7, Nihonbashi Horidome-cho, Chuo-ku, Tokyo 103, Japan Phone: 03-661-6004, 6005 Cabie: UNMANIFACT Telex: J27348 (UNICO)

Universal U.S.A. Inc. 3250 Victor Street, Santa Clara, California 95050, U.S.A. Phone: 408-727-4591-5 Telex: 172247 (UNI USA SNTA) Main Line of Business: Development, manufacture, sales, and exports & imports of amusement machines

European Office 81 Tottenham Court Road, London W1A 1EY Phone: 01-631-1713 Telex: 892989 ELCOIN