CATHODE RAY TOMES

Cyber Cycles Deluxe

Cyber Cycles (World, CB2 Ver.C) (Namco, 1995) · Document · 36 pages · 8 sections · original scan

Page 1

CYBER CYCLES DX Operators Manual

IT IS THE RESPONSIBILITY OF THE OPERATOR TO MAINTAIN CUSTOMER SAFETY AT

ALL TIMES, AND IT IS IMPERATIVE THAT THE DETAILS SET OUT IN THIS MANUAL ARE FOLLOWED PRECISELY.

Part No. 90500039

Page 2

SAFETY WARNING

In Order to Use This Machine Safely

In order to use this machine safely, be sure to read this Operators Manual carefully before installation and use of the machine. Whenever the owner of this machine entrusts disassembly, installation, adjustment, routine maintenance or trouble shooting to another person, the owner should ensure that they read the appropriate precautions and relevant sections of this manual before starting work. In order that no accidents occur when the machine is in operation, strictly follow the notes on safety described below. Also, carefully read section 3, “Precautions”.

Warnings for Operation

( NOTE:

NOTE:
NOTE:
NOTE: Only operate this machine after checking that it has been installed correctly > and in accordance with the manual. Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There is a warning sticker that the player must be able to reach the grey matting of the cycle base with their feet, however if the operator feels that a customer playing the game is in any danger, he should warn the customer accordingly. The warning sticker must always be kept in good condition and replaced if worn so that the customer can read it clearly. If there is an error or problem with this machine, operation must be stopped immediately. )

Warnings for Disassembly, Installation, Routine Maintenance and Troubleshooting

DANGER:
DANGER:
DANGER:
DANGER:
NOTE: Namco Ltd. bears absolutely no responsibility for accidents or injuries )

resulting from unauthorized changes to the machine. Ensure that the machine has been turned OFF before making adjustments or carrying out maintenance. Also ensure only qualified personnel carry out maintenance or turn the power ON to this machine. The power supply and inside the monitor will remain hot and have areas of high voltage even though the machine has been turned OFF, and there is a possibility of burns or electric shock. Be careful not to touch these areas. In order to avoid injuries due to mis-operation, be sure that the voltage of the power supply is within the prescribed limits. Also to prevent possible electric shocks due to failure, this machine MUST be fitted with a securely connected earthed plug. Do not turn the main power switch ON until the machine has been installed correctly. )

Page 3

1. SPECIFICATIONS

POWER SUPPLY :-

MONITOR :-

COIN ACCEPTOR

DIMENSIONS :-

Assembled Cabinet Bike Assy Coin Tower Header

WEIGHT :-

Assembled Cabinet Bike Assy Coin Tower Header

ACCESSORIES :- 220/240volts AC

Philips 46" Rear Projection

Mars CashFlow - 4 Channel

2180(w) x 2640(d) x 2530(h) 1090(w) x 1270(d) x 1930(h) ea. 910(w) x 1370(d) x 930(h) ea. 480(w) x 640(d) x 930(h) 1450(w) x 230(d) x 600(h)

500kg 160kg ea. 65kg ea. 25kg 25kg

Keys: (Cash Door) .. (Coin Door) ... (Service Door) .

Number Decal Set 1-4 ........cccesceeeeeees 2

IEC Mains Lead ....... cesses 1

LINK: Cable cxcsssseseestransaatassarensesonconaes 1

Operators Manual ...........cccccsesseeseeseeee 1

Monitor Manual ............c0csessseseseseeeeeeee 1

M8x40 Security Screw - SUS M8x20 Security Screw - SUS M8 Flat Washer - SUS.... M8 Spring Washer - SUS ... M8x40 Hex Head Set Screw - BZ! M8x60 Hex Head Set Screw - BZP M8 Flat Washer - BZP .... M8 Spring Washer - BZP....

M5 Security Wrench M6 Security Wrench M8 Security Wrench ....

Page 4
  • MAJOR COMPONENTS
Page 5
  • PRECAUTIONS

Be sure to read this section carefully.

3-1 Notes on Operation

(— >)

NOTE: Only operate this machine after checking that it has been installed correctly and in accordance with the manual.
NOTE: Parts of this machine move during game play, so there are places where the distance between the stationary section and moveable section changes. There is a warning sticker that the player must be able to reach the grey matting of the bike base with their feet, however if the operator feels that a customer playing the game is in any danger, he should warn the customer accordingly.
NOTE: The warning sticker must always be kept in good condition and replaced if worn so that the customer can read it clearly.
NOTE: Ensure customers do not get hurt by leaning or climbing on the cycles. Be especially careful in the case of young children.
NOTE: If there is an error or problem with this machine, operation must be LL stopped immediately. )

Parts of this machine lean to the left and right during game play. In order to maintain the customer's safety, the operator should strictly follow the appropriate precautions.

3-2 Cautions When Transporting.

a. Do not subject the game to physical shock when transporting or moving it.

b. Always return the levellers to the UP position before moving the machine, even for short distances.

c. The main cabinets, bike assemblies, coin assy and header assy must be separated before moving or shipping.

d. Take care not to rope any moulded (plastic) parts when transporting.

THIS MACHINE IS NOT DESIGNED TO BE MOVED BY FORK LIFT. DO NOT USE

Page 6

3-3 Cautions When Installing.

This machine is designed for indoor use only. Do Not install the machine in the following places 1.

® Outdoors. [® Direct sunlight, places with excessive humidity or dust, places where there is water leakage, near airconditioning or heating equipment, places with excessively high or cold temperature.

[ @® Places where it would be in the way of emergency exits or fire extinguishing equipment.

®

If this machine is installed next to walls or other machines, ensure that there is 2. plenty of space between them.

Page 7
NOTE: So that customers are not injured by the movement of the bikes, ensure that the machine is separated from walls or other machines by at least 300mm either side and 600mm from the rear of the bikes.
NOTE: In order to gain access to the mains-in connector, ON/OFF switch and link switches, make sure that the rear of the machine is separated from a wall or other machine by a distance of at least 500mm or more.

-4960mm v

00, a a

LLL

Page 8

3-4 Cautions when Handling.

( DANGER The Mains Voltage to this machine must be within the range of *)

220v to 240v AC.

DANGER Be sure that the power is turned OFF when replacing parts and connecting/disconnecting connectors.
DANGER To prevent possible electric shocks due to failure, this machine MUST be fitted with a securely connected earthed plug.
DANGER The monitor and power supply contain areas of very high voltage. Be extremely careful when inspecting or making adjustments.
DANGER When unplugging the game from an electrical outlet, always grasp the plug, not the mains lead. Ne /

NOTES:

. Always return PC Boards to your dealer for repair. Never test the PCB for continuity with a multimeter or similar device. The PCB contains sensitive devices which could be damaged or even destroyed by the internal voltage of such test equipment.

. Adjustments are required after replacing the game PCB, ROM or control pots. Adjustments should be performed as described in section 7-4 "Adjustments when Replacing Parts" (page 25).

. After initial installation or if the number of machines linked together changes, it may be necessary to use the test mode to change the settings and link switch settings. (Refer to section 6-4, "Linking Two Machines" (page 20).

Page 9
  • INSTALLATION

4-1 Assembling the Monitor Cabinets

1.

2. Remove the two rear panels from the right hand monitor cabinet.

Connect the loom connectors of the two cabinets, and place the cabinets together.

Fit, finger tight, the rear joint strap using 4off M8x40 hex head screws, spring and flat washers

Fit, finger tight, the 4off M8x60 hex head screws, spring and flat washers to clamp the cabinets together.

Tighten fully all the hex head screws. (8off)

JOINT PLATE,

Pe ‘M8x40 Hex Head Screw

4-2 Assembling the Coin Tower

1. Connect the loom connectors of the coin tower and right hand cabinet (viewed from the front).

Place the Coin Tower on to the two 'U' brackets of the main cabinet, and push fully towards the cabinet, taking care not to trap any wires.

Open the coin door and fit the 4off M8x60 hex head screws, spring and flat washers to clamp the coin tower to the main cabinets.

Page 10

4-3 Connecting the Bike Assemblies to the Cabinets

  • Connect the connectors between the bike assembly and cabinet.
  • Place the bike assembly onto the support bracket and push the bike against the cabinet taking care not to trap any wires.
  • Fit, finger tight, the 4off M8x40 security screws, spring washers and flat washers, securing the bike to the cabinet.
  • _ Fit, finger tight, the 2off M8x20 security screws, spring washers and flat washers, securing the bike to the support bracket.
  • Tighten fully all the security screws. (6off)
  • Fit the bike number decal to the rear of either side of the bike.
  • Remove the shipping bolts (M10x75) from either side of the bike.
Note:- Retain the shipping bolts in a secure place for re-fitting if the machine is transported. fer “ CONNECTOR

~ \ M8x40 SECURITY SCREW. COIN TOWER

SUPPORT BRACKET

~\_ex20 SECURITY SCREW.

SHIPPING BOLT M8x75 (2 off)_/

Page 11

4-4 Fitting the Header Assembly

To prevent injury, two people should be used to fit the Header Assembly.

1. The Header Assembly is heavy (approx. 25kg), with a forward centre of gravity, so it is important that at least two people are used to fit or remove the Header Assembly.

  • The fitting position of the Header Assembly is very high, and it is important that a means of reaching the height safely, without stretching, is available. (e.g. steps, step stools, etc.)
  • Place the Header Assembly on to the top of the cabinets and pass the loom connectors into the monitor cabinet, taking care not to trap any wires.
  • Fit the 80ff M8x20 Security Button Head Screws, Spring and Flat washers to retain the Header Assembly to the cabinets.
Note:- Ensure that one person maintains the balance of the Header Assembly while the screws are being fitted.
  • Connect the connectors inside the monitor cabinet.
NOTE:-

When the machine is fully assembled and in its final position, lower the 12 level adjusters, (4 on each monitor cabinet and 2 on each bike assy), with a spanner so that all castors are raised from the floor, and the machine is level.

Tighten the lock nuts with a spanner to ensure that the level adjusters do not move.

Level adjuster Lock nut

Page 12
  • HOW TO PLAY

This game is linkable so players can compete against each other on the same track, or compete against computer bikes when playing alone. Two machines can be linked together allowing up to four players to compete against each other.

The Header Assembly displays the position of each rider and also the leading rider.

Speed is controlled by use of the throttle and brake, and steering is controlled by leaning the bike left or right.

After the insertion of a coin/s, credit is established to a bike position with the use of the respective ‘Credit Available' button. Pressing the flashing 'View Change' button, located on the handle bar assembly, will display the Course Select Screen. There are two courses available, "GREEN HILL" is a practise course for beginners and "NEO YOKOHAMA" is an intermediate and advanced course. In a linked game the course is decided by the majority.

Next select a bike. Each player can select one of three bikes:-

"ANTHIAS", for beginners. It corners easily, and its top speed is reduced a little.

"NVR750R",_ for intermediate. This bike has good cornering balance, and its top speed is normal.

"WILD HOG" for advanced. By controlling the special drift, it can cover the course faster than any of the other bikes, but is more difficult to control.

The first player to enter "Bike Select" is also able to select, by using the throttle, the music during the game. The title is displayed in the lower left of the screen.

Players can join in a linked game during the link time countdown. This time can be adjusted in the 'Game Options' mode. If a linked game is in progress but a bike position is available, a player can use this position as a solo game.

When a player completes the specified number of laps in the given time, they complete the game. If the countdown timer reaches 00 before completing the specified number of laps the game is over. At the end of the game, the players ranking, fastest lap time and total time are displayed.

If a best time is beaten the end of the race will be shown and the player can enter their initials by leaning the bike to select the letters and pressing 'View Change' to enter them.

With this game it is possible to change the players viewpoint of the game. Each time the 'View Change' button is pressed the view changes between : "Pillion View", "Rider's View", and "Behind View".

Page 13
  • ADJUSTMENTS

6-1 Turning on the Power

After the machine has been installed, turn ON the power. The power switch is located on the rear of the right hand cabinet.

6-2 Adjustment Switches

The Adjustment switches are located inside the coin door.

1. Service Switch. Press this switch to obtain game credits without incrementing the play meter.

Test Switch Slide the test switch ON to enter test mode. Test mode allows testing and the changing of game settings. (Refer to section 6-3 "Test Mode" (page 12))

COIN COUNTER °

°

TEST LEFT PLAYER O O

SERVICE ce) RIGHT PLAYER O O

TEST SERVICE ‘e)

Service Bracket

Page 14

6-3 Test Mode

  • Open the coin door and slide the test switch "ON". The menu screen will be displayed on the monitor.
  • Select the test required by leaning the bike left or right. The selected test will ‘blink’
  • Enter the selected test by pressing the 'View Change' push button. Select "EXIT" to return the "Menu Screen".
  • After testing is completed, ensure that the test switch is returned to the "OFF" position to return to normal game mode.

The Test Switch must always be in the "OFF" position for normal game mode.

X MENU

COIN OPTIONS

GAME OPTIONS

VO TEST

SOUND TEST

MONITOR TEST

ADS TEST

OTHERS

BANK : CHOOSE VIEW SW : ENTER Sets the price of play (See 6-3-1)

Sets the game options (See 6-3-2)

Used for testing switches and controls (See 6-3-3)

Used for testing sound and setting volumes (See 6-3-4)

Used for adjusting the monitor

Displays accumulated game data

Used for testing the PC Boards and for initializing all of the settings

Page 15

6-3-1 Coin Options

  • Select item (1) "COIN OPTIONS" on the (~ >) the dee en Kg se COIN OPTIONS

€ game cost an [ DEFAULT IN GREEN ]

related settings. GAME COST

  • Lean the bike left or 1 COIN 1 CREDIT right to select the required item then FREE PLAY NO 9 wweeesecceeceeceeedensee (b) press View Change.
  • Use the Brake to EXIT adjust the settings UP or the Throttle to adjust the settings [Bank © :CHOOSE BRAKE :CHANGE+ DOWN, standard | yew sw :ENTER | THROTTLE :CHANGEsettings are displayed ) in green.
  • Select "EXIT" and press 'View Change' to return to the menu screen.
Note :- The price of play on this machine is set within the Cashflow Coin Mech. Ensure that the Coin Options on the screen are set as shown in the following table.

TEM CONTENTS FACTORY SET

  • Game Cost Coins required for 1 credit - - - - - - settable 1-9 1 Coin 1Credit
  • Free Play Yes/No NO
Page 16

6-3-2 Game Options

  • Select item (1) "COIN OPTIONS" on the menu screen to set the game options and related settings.
  • Lean the bike left or right to select the required item then press 'View Change’.
  • Use the Brake to adjust the settings UP or the Throttle to adjust the settings DOWN, standard settings are displayed in green.
  • Select "EXIT" and press 'View Cange' to return to the menu screen.

(— >) GAME OPTIONS [ DEFAULT IN GREEN ]

GAME DIFFICULTY B GAME LAPS GREEN HILL 3 NEO YOKOHAMA 2 ENTRY TIME B ID NUMBER SEAT COLOUR LANGUAGE SOUND IN ATTRACT HI SCORE INITIALIZE EXIT BANK :CHOOSE BRAKE :CHANGE+ VIEW SW :ENTER THROTTLE :CHANGE- LINK ON 1

XN w,

NOTES »

The game difficulty and number of laps and entry time must be set the same on all positions that are linked.

The ID number of the bike furthest left (when facing the front of the machine) should be set to 1, and the other bikes set to 2, 3, or 4in order from left to right. The ID number of the farthest right position should equal the number of bikes linked.

Settings other than those described will cause the machine to operate incorrectly. S

Page 17

TEM DESCRIPTION FACTORY SET

  • Game Difficulty | A (easy) to C (hard) B
(b) Green HillNumber of laps for Green Hill course - - - set 2 - 53
  • Neo Yokohama | Number of laps for Neo Yokohama course - - - set 1 - 5 2
(d) Entry TimeA (longest) to C (shortest)B
  • ID Number Sets bike identity for linked positions. Set so that no linked bikes have the same number

( Machine Linked - Display will show - LINK ON + number of linked units Displays Link Information Faulty Link Cable - Display will show - LINK OFF

Only one machine - Display will show - ON 1

Faulty Link PCB - Display will show - NG

  • Seat Colour Sets the bike colour. Set to match the colour of bike in use
(hy LanguageBilingual, English, NoneEnglish
(i) Sound in Attract| On/ OffOn

() Hi Score hritialize | On / Off of

6-3-3 I/O Test

  • Select item (3) "I/O Test" on the menu screen to test the switches or lamps.
  • Lean the bike left or right to select the required item then press View Change.
  • Select "EXIT" and press 'View Change' to return to the menu screen.

Va

BANK \ VIEW SW :ENTER ) VO TEST

DIP 4 12845678 oesesesssssseseeeeseefeece (a) LINK ON vessesssscssseeeeeenfeee (b)

SWITCH TEST MOTOR TEST LAMP TEST EXIT

:CHOOSE

  • Shows condition of DIP SW 4 on the PCB. In normal operation all switches are OFF. (If a switch is ON it will be displayed in red).

Switch 1 if ON will force the PCB in to Test Mode.

Switch 8 if ON will freeze the picture on the monitor.

  • Shows if the game is linked.
Page 18

6-3-3-1

1.

6-3-3-2

6-3-3-3

1. Switch Test

Select Switch Test from the "I/O Test" menu. The following screen will appear on the monitor.

( SWITCH TEST >)

TEST SwON..(a)

COIN SW ON b)

SERVICE SWON...(c)
BANK00 CENTRE .(a)

THROTTLE 00 e)

BRAKE00...(f)
VIEW-SWONreeeessseefeee (g)

, BRAKES THEOTILE: EXIT

The word 'ON' will appear next to items a, b, c, and g each time the respective switch is operated. When the bike is pushed left, 'CENTRE' will go off and 'OK' appear just before it reaches the extreme left, '00' will decrease. When the bike is pushed right, ‘CENTRE ' will go off and 'OK' appear just before it reaches the extreme right, '00' will increase. When the THROTTLE or BRAKE are operated, 'OK' will appear just before they are fully on, and '00' will increase.

Operate the brake and throttle together to exit and return to the "I/O Test" menu screen.

Motor Test

This test is not used on this machine

Lamp Test

Select Lamp Test from the "I/O Test" menu. The following screen will appear on the monitor

( LAMP TEST )

ALL LAMPS RED YELLOW BLUE

GREEN VIEW-SW

VIEW-SW: EXIT Ne

Page 19
  • The lamps will automatically illuminate in turn as indicated on the screen.
  • Press 'View Change' to return to the "I/O Test" menu screen.

6-3-4 Sound Test

  • Select item (4) "Sound Test" on the menu screen to test the sound and speakers.
  • The following screen will appear on the monitor.

( > SOUND TEST [ DEFAULT IN GREEN ]

VOLUME FRONT LEFT SP. 55 FRONT RIGHT SP. 55 TANK SP. 50 REQUEST SONG No. 000

MESSAGE ETC, nnnccnnnennnnfenee (e) EXIT

BANK :CHOOSE BRAKE :CHANGE+ VIEW SW :ENT/ON,OFF THROTTLE :CHANGE-

\ vy,

  • Select the required item by leaning the bike left or right. The selected item will 'blink'.
  • Operating the brake will increase the value setting and operating the throttle will decrease the value setting. Standard values are displayed in green.
  • Press 'View Change' to start or stop a Regest Song No. sound. (Request Song No. 3 will generate a stereo sound test.
  • Select "EXIT" and press 'View Change' to return to the menu screen.

Item Description Factory Set

aSetleftspeaker volume==——_------00 Quietest - 63 Loudest32
bSetrightspeaker volume=- - -- --00 Quietest - 63 Loudest32
cSet bike tank speaker volume —- -- -- -00 Quietest - 63 Loudest32

Select sound for testing. Each number will produce a different sound. 000 will generate a stereo test.

eDisplays song namesee
Page 20

6-3-5 Monitor Test

  • Select item (5) "Monitor Test" on the menu screen to set up and adjust the monitor.
  • Onentering monitor test, the following screen will appear on the monitor.

( MONITOR )

GRADATION PATTERN CROSSHATCH GREEN CROSSHATCH WHITE WHITE WINDOW (H) WHITE WINDOW (M) WHITE WINDOW (L) INTERLACE PATTERN VIEW ANGLE ADJUST (CRT) VIEW ANGLE ADJUST (PROJECTOR) FULL WHITE EXIT

BANK :CHOOSE VIEW-SW :ENTER Ne S

  • Lean the bike to select a test and press 'View Change' to enter the test and to return to "Monitor Menu" from a test.

6-3-6 ADS Data

  • Select item (5) "ADS Data" on the menu screen to view machine history details.
  • The following screen will appear on the monitor.

4 ADS )

POWER ON 00'00"00 PLAY TIME 00'00"00 PLAY TIME AVE —00'00"00 PLAY NUMBER 0000 e2etD

COURSE-VIEW —haceseesesedeeeeee COURSE-BIKE COURSE -LINK COURSE-C. P. COURSE-P.T. SSSSE

INITIALIZE eeesssedheeeee (i) EXIT

BANK :CHOOSE i VIEWS :ENTER

Page 21

Item Description

  • Power On Total time in hours, minutes, seconds machine has been switched on.
  • Play Time Total time in hours, minutes, seconds that machine has been in play.
  • Play Time Ave Average time of game duration.
  • Play Number Total game plays.
  • Course-View Time for each view.
  • Course-Bike Number of times a bike has been selected.
  • Course-Link Number of linked games played
  • Course-C.P. Position on the course at game over.
  • Course-P.T. Total time each course has been played.

() hiitialize Reset all data.

6-3-7 Others

  • Select item (6) "Others" on the menu screen.
  • Onentering 'Others' the following screen will appear on the monitor.

4 OTHERS )

AUTO SETTING

BACK UP MEMORY INITIALIZE

PCBTEST —ineeedhcceeeee (c)

EXIT

BANK :CHOOSE «VIEW SW ‘ENTER

Item Description

  • Auto Setting Will adjust all linked units to match automatically.
  • Back Up Memory hnitialize | Reset all ADS data

() PCB Test For testing the Game PCB

  • If the game is linked, this option allows all linked positions to be set from position No. 1 bike. If all game and coin options shown on the screen are correct, select transmit, then push View Switch. All positions will automatically update to the displayed options and ID No. All screens will display the Auto Setting screen. Set each bike colour from each Auto Setting screen.
Note: Any game in play will be lost during Auto Setting transmit.
Page 22

6-4 Linking Two Machines.

Up to two machines (4 bikes) can be linked together. The machines should be linked as described below.

  • Ensure that the power is “OFF”.
  • Loosen the two screws (M5x12) on the back of the right monitor cabinet, and remove the connector cover.

Connector cover

screw (M5x12)

  • Set the link switches to “ON” , “EXT”, and “ON”. (See Diag.) Link switches
  • Use the supplied link cable and connect the machines between “IN” and “OUT” sockets (See Diag.)

[Examples of Linked Machines]

  • 2Machines © oO © oO (4 Seats) IN OUT IN OUT
  • Turn the power to each machine “ON”, and set the PCB ID using the test mode. (Refer to section 6-3-7, “Others” 'Auto Setting' (page 19))
Note: Settings other than those described will cause the machine to operate incorrectly.
Page 23

6-4-1 Setting the Link Switches

The link switches are used to set the connection between seats and machines.

1). Setting only one machine (2 bikes)

Set the link switches to “ON”, “INT”, and

Note: Do not use a link cable.
  • Setting two or more machines. ° @ O| ox wr ow lO

Set the link switches to “ON”, “EXT”, and a (4 al

“ON”. ° oion @oLkX a jo

  • _ Install the connector cover using ° Screw M5x12 the two screws (M5x12).

The link procedure is now complete.

Link cable

  • Setting for faulty PCB. If the game PCB of only one bike is faulty, set the link on that bike to “OFF”

[Example of setting for faulty left side]

Bike with probler

Page 24
  • MAINTENANCE
DANGER: In order to prevent injury or electric shock to service personnel, ensure that the MAIN POWER IS OFF before attempting any maintenance.
DANGER: Before performing any work not described in this manual, be sure to contact your distributor to receive instructions or answers to questions.

7-1 Replacing the Fluorescent Tube, Position, and Leading Driver Lamps

  • Remove the three security screws (M5x12), and remove the plexi upper retaining bracket.
  • Remove the three security screws (M5x12), and remove the plexi lower retaining bracket.
  • Remove the header plexi.
  • Unscrew the defective position lamp and replace.
Warning:- Ensure that the lamp is not hot before touching it.

7-2 Replacing the Signal Lamps

  • Remove five security screws (M5x12), and remove the signal plexi L or R.
  • Unscrew the defective lamp and replace.
Warning:- Ensure that the lamp is not hot before touching it.

Signal Plexi (L) Uppér Retaining Brkt

Msx12 Secutity Screw

Fluorescent Tube

MSx12 Security Serew Header Plexi

Lower Retaining Brkt Leaging Driver Lamp — 'signal Plexi (R) M5x12 Seturity Serew Position Lamp

Page 25

7-3 Handle Bar Assembly

Remove four M5X12 security screws, and remove handle bar assembly cover to gain access to the throttle and brake controls.

NOTE:- The game must be re-initialized whenever the PCB, ROMS, Throttle, Brake or Steering controls are replaced. (See 7-4 "Adjustments when Replacing Parts")

7-3-1

1)

7-3-2

1)

4) Replacing the Throttle Control Pot

Slacken the grub screw M8X5 securing the control pot shaft to the drive gear, and remove the gear.

Replace the control pot ensuring that the wires are replaced to the correct terminals.

Turn the control pot shaft until the flat is vertical and to the right, when looking at the shaft. Replace the drive gear ensuring that the control pot shaft does not turn and the grub screw in the drive gear is on the flat of the shaft

Re-tighten the grub screw M3x5

Replacing the Brake Control Pot

Slacken the grub screw M83X5 securing the control pot shaft to the brake assembly.

Replace the control pot ensuring that the wires are replaced to the correct terminals. GRUB SCREW M3x5 BRAKE CONTROL POT

GRUB SCREW M3x5.

FLAT ON SHAFT

CONTROL POT SHAFT POT BRACKET

THROTTLE CONTROL POT

CONTROL POT

DRIVE GEAR

GRUB SCREW M3x5.

When replacing the control pot, ensure that the flat on the control shaft is in line with the grub screw.

Re-tighten the grub screw M3x5.

Page 26

7-3-3 Replacing the Steering Control Pot

  • Remove three security screws (M5X16) and four security screws (M5x12) from the right hand bike vac-form, and remove the vac-form.
  • Slacken the grub screw (M4x5) to release the control pot shaft.
  • Replace the control pot, taking care that the wires are fitted to the correct terminals.
  • Re-tighten the grub screw (M4x5), ensuring that it engages the flat of the control pot shaft.
  • Refit the bike vac-form, and the security screws (M5x12) (M5x16).

SECURITY SCREW (M5x16) SECURITY SCREW (M5x12)

SECURITY SCREW (M5x16)

MOUNTING BRACKET

EARTH TAG.

GRUB SCREW Max5 A TOP view

GRUB SCREW Max5

CONTROL POT

A SIDE VIEW

Page 27

7-4 Adjustments When Replacing Parts (Initialization)

The following adjustments must always be carried out after replacing the Game PCB, ROMS, or Throttle, Brake, and Steering Control Pots. The game will not operate correctly if these adjustments are not made.

1.

4.

5. Ensure that the Throttle and Brake are fully released and the bike is in its central upright position.

Turn the Test switch on while pressing the Service switch. The following screen will be displayed.

Adjustment is complete when the screen displays ‘Initialize Completed’.

Operate the Brake and Throttle together to return to the "Menu Screen".

Turn the Test switch OFF to return to normal game mode.

Note:- If the 'View Change' button is flashing during standby mode, there is a problem with one of the control pots (Throttle, Brake, or Bank) not being at zero. Enter ‘Switch Test' (See 6-3-3-1 ‘Switch Test' page 16) to determine which pot is not at zero and either replace if faulty or reinitialize.
Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

ITEM DESCRIPTION PART No.

1PHILIPS 46" REAR PROJECTION MONITOR84000003
2FRONT GLASS37100074
3LOUDSPEAKER GRILLE (W / NAMCO LOGO)45000557
4SUS COVER BRACKET EXTENSION - TOP45000562
5.CREDIT AVAILABLE WHEN LIT’ PUSHBUTTON ASSEMBLY60200215
6SUS COVER BRACKET EXTENSION FRONT - LHS45000556
8SUS COVER BRACKET COIN TOWER - TOP45000565
9SUS COVER BRACKET COIN TOWER FRONT - LHS.45000564
10CYCLE JOINT BRACKET "A"45000555
ablSUS COVER BRACKET EXTENSION - RHS.45000566
12ADJUSTABLE FOOT M16x95,88300079

SMPSU 5v/30A 12v.5A 83000004

FUSE 1... 3A SLO-BLO 63500547

6FUSE 1..." 2A SLO-BLO63500506

FUSE 1..." 2A QUICK-BLO 63500504

14SWIVEL CASTOR 75mm59000009

SCHAFFNER MAINS-IN FILTER ASSY 66000016

*FUSE 20mm 5A63500601
16SCHAFFNER BOOT66000017
174%s' 20w SPEAKER62000006
18FRONT GLASS RETAINING BRACKET - LOWER45000452
19FRONT GLASS RETAINING BRACKET - UPPER,45000451
20CABINET EXTENSION DECAL - TOP40000258
21CABINET EXTENSION DECAL - LHS40000259
22CABINET EXTENSION DECAL - RHS40000260
23PROJECTOR CABINET DECAL - LHS/RHS40000256
24COIN TOWER DECAL - TOP40000261
25SUS COVER BRACKET COIN TOWER FLAT - LHS.45000569
26SUS COVER BRACKET COIN TOWER FLAT - RHS45000570
27SUS COVER BRACKET COIN TOWER FRONT RHS:45000563
28INTERLOCK SWITCH D.P.D.T.60000006
29INTERLOCK SWITCH COVER39000028
Page 30

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 31

TEM DESCRIPTION PART No 1 _| evOLE BASE Frame 48000871 2 _| BEARING MOUNTING ASSEMBLY 000882

2| RocKER PLATE5000894

4 _| ROTARY MOULDING SUPPORT BRACKET -LHS 2000816 3 _| ROTARY MOULDING SUPPORT BRACKET - RAS aso00816

|ROSTA BRACKET4000897
7| CONNECTOR COVER4000881

@ | EvaFLOOA wAT- GREY 000889 2 _| POTENTIOMETER BRACKET 000898

10_|seacen5000898
|space45000886
12_|SPAcER75000886

ROTARY NOULDNG - BLACK ‘4000501

ROTARY MOULDNG RED asoo0e02

:ROTARY MOULDING - YELLOW45000503

ROTARY MOULONG BLUE s000804

LOWER VAC-FORM FHS -BLACK ‘000805

LOWER VAC-FOAM FHS -RED ‘000806

*LOWER VAC-FORM RHS - YELLOW45000507

LOWER VAG-FORW RNS BLUE 000808

LOWER VAC-FORM LHS -BLAGK s000809

LOWER VAC-FORM LHS - RED 000610

*LOWER VAC-FORM LHS - YELLOW45000511

LOWER VAC-FORM LHS - BLUE asoo0612

4_|#2 20w SPEAKERszn00006

16 _| Sear vac-Fonm 000618

17_|eno oF STROKE BUMPERses00634
1e_|PLLOW BEAANG-FYH//UPG 207ees00688
te| Rosta SPANG- DASE? x 100xEH09.261~
20| SWWEL GASTOA 6smmseo00002
at_|aosustaa.e Foot tes8800078
22_|NaMGO LOGO ROTARY MOULDING0000238
23| NAMGO LOGO vAC-FORM0000236

TAR INTAKE DECAL FRONT LS oo00281

“AIR INTAKE DECAL FRONT - RHS-40000242

AR INTAKE DECAL SDE - LHS oo00248

=AIR INTAKE DECAL SIDE - RHS40000244
26| CYBER CYCLES LOGO VAC FORM0000237

REAR DEGAL ROTARY MOULDING - LHS 40000238

aREAR DECAL ROTARY MOULDING - RHS40000240

20 _| CHROME DECAL REAR UNDERSDE 0000246

CHROME DEGAL SDE LHS 0000246

“CHROME DECAL SIDE - RHS40000247

go _| SUS #00 FLOOR MAT COVER BRACKET s0000%80

ot_|FLLER GaP vac-Fomm61700828
o4_|C\OLE BASE SAFETY DECAL REAR000282

26 _ | CYCLE BASE SAFETY DECAL -LHSRHS 0000288 ce _| POTENTOMETER xo0e0o0as

Page 32

g,

Page 33

ITEM DESCRIPTION

HANDLE BASE

GRIP SHAFT (A)

GRIP SHAFT (B)

THROTTLE STOPPER

THROTTLE SPRING

WASHER PLATE,

THROTTLE GEAR

BRAKE PIN

BRAKE STOPPER

STOPPER ROD

"1 UPPER BRAKE PLATE

BRAKE SPRING

BRAKE CONTROL POT BRACKET

SLIDE PLATE

HANDLE COVER

DECAL SET

RUBBER GRIP

SPRING SPACER

GRIP SHAFT GEAR

FLANGE BUSHING - LFF 2010

FLANGE BUSHING - LFF 0705

FLANGE BUSHING - LFF 1015

FLANGE BUSHING - 80B 2025

THROTTLE SPACER

BRAKE LEVER

BRAKE BASE

BRAKE SPACER

THROTTLE PIN

BRAKE WASHER

PUSHBUTTON ASSY

POTENTIOMETER

'C’CLIP

Page 34

ITEM DESCRIPTION PART No.

1RACE START VAC-FORM - LHS.45000452
2TOP ACRYLIC RETAINING BRACKET45000537
33ft FLOURESCENT TUBE64500013
4RACE START VAC-FORM - RHS.45000453
5E14 25watt GOLF BALL LAMP64000084
7TOP ACRYLIC30000040
8E14 25watt REAR SILVERWED LAMP64000083
B1M5x16 SUS SECURITY BUTTON HEAD SCREW26300032
Page 35

sence ue SERVICE BRKT

Test LR FLUORESCENT ASSY

Ex} Zr

METER snuveL

seer sey ALIS ro a i LAMP DRIVER PCB i

COTTE RE Tees Laps STLEADER LARPS foeeeN LANE, ST

aHtee caneeae

ere Teer conn mime ae —te Tet Eee = Lae rap S15 Teast Ca aarae tae i SIRI © ABLE L

ise ERT al (| nhl

EH EEEE

SWITCH MODE POWER SUPPLY

na nt

  • VEL BLK een eu
[NDste eeerans

fe AUCELE LHP 919 fA zte

ES:1 teeorwvenStS

ch. tee a riseanse Si aU fs SEE EED

CREDIT DISPENSE

i \

iSCHAFFNER MAINS-IN ASSY = jINTERLOCK

il 3 AMP | “2 1 1 ‘——_BLUE_} Jasfefolo} Hlslofe fale] ~~

ell a Bel lal Gi 1

Line pCR!

Page 36

wal | : mae Parmer FED LAP FAIR Laas TH

a

Cer Ba Bu RET CNL RIGHT CHL i

LEFT ean Gat AGH cae |

pans pail rem

z Aiea uot + tebe PCB ASSY Ler

EIGHT -CPERRER TT EET TREE

x1

AMPLIFIER PCB! Lar

BIE SPraRER + [ HIE SPraKEE =f ae

ey ics aust

emrteT

i

J But

PAWEL THT Gee Tare mace ets Sa rnt fro compra iat at}

ceeovvewow Palle

th PUppLe BACK

PWT tf HE

istahn Seat? mow

px es?

Row a rales i i

Cleat GREEN

Lceeowveuow CaEIEE AE

fete ED scant

46° PROJECTOR

BANK <sTEERING

‘rin (vRa

MONITOR LER

POEL BLK To

©) deen LEADING DRIVER ©

iS POSITION LAMPS LER

Lpig pos 3

Gye x seeEN GREY pis SIAL TOP

bic

LP. cIGwAL BOTTOM SIGNAL LAMPS L&R