CATHODE RAY TOMES

I-Robot TM-251 1st Printing

I, Robot (Atari, 1983) · Technical Manual · 62 pages · 58 sections · original scan

Page 1

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 2

Atari Customer Service

If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at one of these Atari Customer Service offices:

UNITED STATES

Parts and Service

Atari, Inc. California Customer Service Office 737 Sycamore PO, Box 906 Milpitas, CA 95035, Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Pacific Time)

oO Anywhere in the U.S. including Alaska and Hawaii

. (408) 943-1120

EUROPE

Parts and Service

Auri Ireland Limited European Customer Service Office Tipperary Town, Ireland 1elex 28169 (Monday-Friday, 9:00-6:00 pm GMT) B 062-52155

Page 3

Operators Manual

With Illustrated Parls Lists

Page 4

© 1984 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored ina retrieval system, transmitted, or otherwise copied for public or private use, without permission trom the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic dia grams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can tmpound infringing articles while legal action is pending, If infringers are convicted, courts can order destruction Ot the infringing arucies. In addition, the Act provides for payment of statutory damages of up to $250,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up w five yeas. : . Auri will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games madc by us. Anyone who purchases such copies risks forfeiting such a game.

Published by: Atari, Inc. 790 Sycamore Drive PO. Box 906 Milpitas, California 95035

Printed in the U.S.A. 5N

Page 5

Notice.Regarding Non-ATARI Parts

Use of nion-ATARI parts or modifications of any ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.

You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:

  • Substitute non-ATARI parts in the game.
  • Modify or alter any circuits in the game by using kits or parts not supplied by Atari.

NOTE

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing, device pursuant to Subpart J of Part 15 of Federal Communications Commission (FCC) Rules, which are designed to provide reasonable protection against such interference when operated ina commercial environment. Operation of this equipment in a residential area or modification to this equipment is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference. If you suspect interference from an ATARI® game at your location, check the following: © All green ground wires in the game are properly connected as shown in the game wiring diagram

  • The power cord is properly plugged into a grounded three-wire outlet. © The game printed-circuit boards (PCB) are properly installed within the Electromagnetic Interference (EMI) cage. ° The EMI Shield PCB is properly instafled and connected in series with the game PCB harness. © All filter capacitors required On the EMI Snield PUB are properly soldered in place. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover of this manual for service in your area.

iii

Page 6

1, ROBOT ~

Table of Contents

1 Set-Up How to Use This Manual as Game Overview . . 13 Inspecting the Game 13 Joystick Centering 13 Switch Locations . . . 14 Selecung dic Opduns 14 Game Play 15.

2 Self-Test SelfTest Displays 0.0002. eee eee tte 2-2

3 Maintenance Preventive Maintenance Removing the Control Panel .. . Lubricating the Joystick Control Cleaning the FIRE Switches . . - Tightening the Start Switches

Corrective Maintenance .. Removing the Joystick Control . Disassembling the Joystick Control Reassembling the Joystick Control Removing the Start Switches Removing the FIRE Switches

4 Mlustrated Parts Lists Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4.6 Figure 4-7 Figure 4-8 Figure 4-9 Figure 4-10 Figure 4-11 Cabinet-Mounted Assemblies Control Panel Assembly . . Hall-bIfect Joystick Assembly « Utility Panel Assembly Fluorescent Tube and Speaker Assembly . Coin Controls, Inc. Coin Door Assembly . Coin Acceptors, Inc. Coin Door Assembly . Printed-Circuit Board Mounting Hardware Central Processing Unit PCB ——_ tee Video PCB Assembly ....... EMI Shield PCB Assembly

Page 7

List of Illustrations

Figure 1-1 Figure 1-2

Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 2-9 Figure 2-10 Figure 2-11

Figure 3-1

Table 1-1 ‘Table 1-2 Table 1-3

‘Table 21 Table 3-1 I, ROBOT Game Overview 1-2 Switch Locations. 14

Accounting and Options Display . . . 2-2 Hardwatc Tesi—Passes Display... 23 Hardware Test—Fails Display . 23 Joystick Test | Display. Lee 2-4 Toystick Test 2 Display ......... - 24 Sound Test Display... . 2-4 Alphanumerics Display .. 25 Dot, Vector, and Polygon Test Display . . 2-5 Color Bars Display . . . 25 Grid Pattern Display . . . 26 Size and Centering Display... 26.2... 26

Lubricating, Disassembling, and Reassembling the Hall-Effect Joystick .........00000 000.0020 c cece eee 3-5

List of Tables

Installation Specifications . . 13 Switch Settings for Bonus Int and Play Options . . 14 Switch Settings for Coin & Credit Options and Bonus Adder . 15

RAM Locations 6... ieee eee eee eee 24 Recommended Preventive Maintenance Intervals . . 3-2 1, ROnOT

Page 8

Safety Summary

‘The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will he found thronghoue this manual where they apply.

& WARNING A Properly Ground the Game. Players way receive an elecuival shock if this gare is not properly grounded! To avoid electrical shock, do not plug in the game until it has been inspected and properly grounded. This game should only be plugged into a grounded 3-wire outlet. If you have only a 2-wire outlet. we recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if the control panel is not properly grounded! After servicing any parts on the control panel, check that the grounding clip is firmly secured to the metal tab on the inside of the control panel. Only then should you lock up the game. AC Power Connection, Before connecting the game to the AC power source, verify that the proper voltage-selection plug is installed on the game’s power supply. Disconnect Power During Repairs. To avoid electrical shock, disconnect the game from the AC power source before removing or repairing any part of the game. When removing or repairing the video display, extra precautions must be taken to avoid electical shock because high voltages may exist within the display circuitry and cathode-ray tube (CRT) even after power has been disconnected. Do not touch internal parts of the display with your hands or with metal objects! Always discharge the high voltage from the CRT before servicing this area of the game. To discharge the CRT: Attach one end of a large, well-insulated, 18-gauge jumper wire to ground. Momenuarily touch the free end of the grounded jumper to the CRT anode by sliding it under the anode cap. Wait two minutes and discharge the anode again. Use Only ATARI Parts. To maintain the safety integrity of your ATARI game, do not use non- ATARI parts when repairing the game. Use of non-ALARI parts or other modifications to the game circuitry may adversely affect the safety of your game, and injure you or your players. Handle Fluorescent Tube and CRT With Care, if you drop a fluorescent tube or CRT and it breaks, it may implode! Shattered glass can fy six feet or more frum dhe implosion. Use the Proper Fuses. To avoid electrical shock, use replacement fuses which are specified in the parts list for this game. Replacement fuses must match those replaced in fuse type, voltage tating, and current rating. In addition, the fuse cover must be in place during game operation.

CAUTION

Properly Attach All Connectors. Make sure that the connectors on each printed-circuit board (PCB) are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty. Ensure the Proper AC Line Frequency. Video games manufactured for operation on 60 Hz line power (ie., United States) must nat he operated in conntries with 50 Hz line power (ie., Europe). The fluorescent light ballast transformer will overheat, causing a potential fire hazard if 60 Hz games are operated off power lines using 50 Hz. Check the product identification label of your game for the line frequency required.

Page 9
WARNING Shock Hazard To avoid electrical shock, do not plug in the game until it has been inspected and properly ‘set up for the line voltage in your area. This game should only be connected to a 3-wire outlet. If you have only a 2-wire outlet, wwe recommend you hire a licensed electrician to install a grounded outlet. Players may receive an electrical shock if this game is not properly grounded! Do not touch internal parts of the display with your hands or metal objects!

Set Up

How to Use This Manual

‘This manual, written for game operators and service tech. nicians, describes your new ATARI game. Chapter 1 contains a game overview, game specifications, inspection procedures, switch locations, option information, and a description of game play. Chapter 2 contains self-test procedures. Chapter 3 contains maintenance and repair procedures. Chapter 4 contains illustrated parts lists. Notes in this chapter refer you to other places in the manual for more detailed information Schematic diagrams of the game circuitry are included as asupplement (SP-251) to this manual.

Chapter 1

Page 10

Set Up 1, KUDU:

Aluavlien Panel Fluerescent Tube & Gp. See Figure 4-1 See Figure 4-5 Game (dentification Label x

Control Panel Assy { Video Display + See Figure 4-2 See Service Manual

Head Access Panel

Joystick Assy San Figure 4-3

Lower Speakers Soo Figure 41

CPUPCB+ See Figure 4-9

Utility Panel Assy See Figure 4-4

Goin Door See Figures 4.6 447

Switching Power Supply Assy « See Figure 4-8 and Service Manual

EMI Cage Assy See Figure 4-8 Power On/Off Switch EMI Shield PCB Video PCB See Figures 4-8 8 4-11

Items with a serial number label See Figure 410

Figure 1-1 Gast becew tow

1-2

Page 11

1, ROBOT

Game Overvicw ‘The player is an Interface Robot (#1984) in rebellion against Big Brother and his Evil Eyes in 1, ROBOT. Players will euler another world where they must face off against Big Brother on different terrains, trying to shoot through a protective shield and advance to the pyramid where Big Brother’s Evil Eye can actually be shot and destroyed I, ROBOT provides players with exciting challenges as they attempt to lead a rebellion against the control of Big Brother.

New Features

I. ROBOT has several new feanres- « Changing Perspective. By pressing the start pushbutton while in Game Play, players can change their viewpoint on the playfield. It takes them from an overhead view of the entire terrain to a ground-level view, where shooting the enemy is worth more points. ¢ 3-Dimensional Graphics. All objects in 1, ROBOT are really three-dimensional.

  • Doodle City. By entering the Transporter, players can go to Doodle City. The players can manipulate the I, ROBOT graphics in an infinite variety of shapes, colors, and patterns.
  • Hall-Effect Joystick, This new analog joystick provides a faster and smoother response for the player.

All major parts of the game are illustrated in Figure 1-1

Inspecting the Game

Please inspect your game carefully to ensure that it was delivered to you in good condition.

  • Examine the exterior of the game cabinet for dents, chips, or broken parts. 2, Remove the screws from the body rear access panel. Unlock and open this panel and the coin door. Inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game Tauucsses) ale firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a printed-circutt board (PCB) and wiil void your warranty. b. Ensure that all plug-in integrated circuits on each PCB are firmly plugged into their sockets, Set Up

cc. Remove the tu-wrap that svuucs dic UUlicd power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair of replace it as required. Place the square strainrelief plate in the wood slot at the bottom of the rear panel opening. d. Inspect the power supply. Make sure the harness is plugged in correctly.

Replace fuses onty with an identical type fuse with the same electrical rating. Please refer to ‘TM-261 (the switching power supply manual) for information about fuse values in your game.

e. Inspect other major subassemblies, such as the control panel, video display, EMI cage, and each PCB. Make sure they are mounted securely and that the grccn ground wires arc conuecicd.

NOTE Before applying power to the game, make sure the joystick is resting in the middle of its housing. If it is not, the electrical centering of the joystick may be disrupted.

f. Plug the game into a grounded 3-wire outlet. Perform a self-test as described in Chapter 2.

Table 1-1 Installation Specifications Characteristic Specification

Power Consumption 240 W Nominal ‘Temperature +5° to +38° C(+37° to +100° F) Humidity Not to exceed 95% relative Line Voltage 100 to 240 VAC Width 25.25. (G41 cay Depth 36 in (91.5 cm) Height 68.5 in (174 cm)

Joystick Centering

Electrical centering for the joystick is quickly accomplished by moving the joystick to all four extreme edges. Electrical centering is also accomplished during normal game. play, but may take a few seconds to optimize.

Page 12

Set Up

Switch Locations

Power On/Off Switch The power on/off switch is located on the back of the cabinet on the lower left side (see Figure 1-1).

Utility Panel Switches The volume control, coin counter(s), self-test switch, and auxiliary coin switch are on the utility panel. The utility panel is located inside the upper coin door (see Figure 1-1). The volume control adjusts the level of sound produced by the game. The coin counter(s) records the number of coins entered into the game. The self-test switch initiates the self-test mode. The auxiliary coin switch credits the game without activating a coin counter. See Figures 1-2 and 4-4 for details of these switches.

Option Switches ‘Two dual-inline package (DIP) switches are located on the Central Processing Unit (CPU) PCB at locations 3J and 5E (see Figure 1-2). Use these 8-toggle switches to select uit ferent bonus, pricing, and play options.

Selecting the Options

Settings of the option switches are explained in Tables 1-2 and 1-3. Options preset at the factory are shown by the <4 symbol. However, you may change the settings to suit your individual needs.

  • ROBOT

Table 1 2 deocribes the settings for the 8.toggle cwitch at Jocation 5E on the CPU PCB. This switch selects both the bonus life intervals available and the game play options. Table 1-3 describes the settings for the 8-toggle switch on the CPU PCB at location 3J. This switch selects the game price options available and the bonus adder. To verify option settings, refer to Chapter 2.

Volume Control

Coin Counter

™ Self-Test

Auxiliary Switch

Coin Switch

Figure 1-2 Switch Locations

Table 1-2 Switch Settings for Bonus Interval and Play Options

1 3 4 5 6 7 Settings of 8-Togyle Switch uu CPU PCD (at focation 5E) 8 Option

Off Off On Off

On On Of Off off On

Off On

On On

Off ck. ou

On Off off On Bonus Life Intervals None 20,0004 30,000 50,000 Bonus Lives Per Coin 5 Lives 4 Lives 3 Lives<t 2 Lives

Minimum Game Time Option 90 Second Minimum Game Time on Level 1 3 Lives (Limited Game Time) Medium Difficulty Level Easy Difficuity Level

Demuisuativn Mode On Demonstration Mode Off-4

On Doodle City for 2 Minutes 10 Seconds~4 Of Doodle Ciry for 3 Minutes 5 Seconds

“4 Manufacturer's recommended settings for American-made games.

Page 13

1 RAROT oecup

Table 1-3 Switch Settings for Coin & Credit Options and Bonus Adder

Settings of 8-Toggle Switch on CPU PCB (at location 3) 8 Option

123456

On On On Off

Off On

Off Off

On Off

On On Off Off

onOnOn
OnOnOff

Off On Off

On Off On

Off On On

On Off Off

OffOffOn
OffOffOff

Right Coin Mechanism 1 Coin for 1 Coin Unit« 1 Coin for 4 Coin Units 1 Coin for $ Coin Units 1 Coin for 6 Coin Units

Left Coin Mechanism 1 Coin Unit for 1 Credit<4 1 Coin Unit for 2 Credits

Coins Per Credit On 1 Coin for 1 Credit~4 Off 2 Coins for 1 Credit On 3 Coins for 1 Credit Off 4 Coins for 1 Credit

Bonus Adder No Bonus 2 Coin Units for 1 Credit 3 Coin Units for 1 Credit 4 Coin Units for 1 Credit 5 Coin Units for | Credit 4 Coin Units for 2 Credits No Bonus Free Play

“4 Manufacturer's recommended settings for American-made games.

Game Play

NOTE The message TEST AND CENTER JOYSTICK may appear during game play. If this occurs, enter the celftest mode (cee Chapter 2) and center the joystick.

1, KOBUL begins with the Intertace Kobot facing ott against the Evil Eye. The player has to collect all of the red squares on the playfield in order to destroy the shield that protects the Evil Fye and enter the pyramid. The Robot can only jump to the red squares when the Evil Eye is not watching (i.c., yellow or green). Lf the Evil Eye is red, it will detect the Robot jumping and destroy him. At the acquisition of each red square, the protective shield is weakened. When the Robot has obtained all of the red squares, the shield is automatically destroyed and the Robot can get into the pyramid and destroy the Bvil Eye. After the destruction of the Evil Eye, the Robot travels through a space wave where the player must either shoot and destroy or avnid the abjects flying tawards him Atthe completion of each space wave, the Robot lands on another geometric terrain, where once again he must face another Evil Eye.

Every third terrain contains red pyramid which the Robot must enter after destroying the Evil Eye. Once inside the pyramid, the Robot has one chance to collect as many of the jewels as he can before he is destroyed. If the Robot is destroyed while inside the pyramid, he is immediately thrust back into space, The player must get through three more terrains, and destroy three more Evil Eyes before he has another chance to get the jewels inside of the pyramid.

Hints for Game Play © The player can advance to higher play levels while inside the Transporter.

  • Objects to be destroyed for points include a buzz saw, a soccer ball, a small ball dropped by a bird, the polygons, and a rolling log.
  • The player can achieve a bonus for shooting all of the tetrahedrons in a space wave. The player can also achieve bonus points by spelling / ROBOT by shooting the letters as they appear sequentially in Space waves.
  • The player must shoot the polygons with SEVEN shore in arder ta destray them and achieve points.
Page 14

Self-Test Procedure

This game will test itself and provide data to show that the game circuitry and controls are operating properly. Selftest data is presented visually on the video display and audibly through the speakers. No additional equipment is required, ‘We suggest you perform a self-test when you first set up, each time you collect money, change the game options. or SuspuLl gauue failure,

Chapter 2

Page 15

Self-Tese

Self-Test Displays

Ten self-test displays provide a visual check of the following:

  • Game accounting and option-switch information.
  • Read-only memory (ROM) and random-access memory (RAM) circuit operation.
  • Joystick and switch operation.
  • Sound-generator circuit operation. = Mathbox circuit uperation. ¢ The Dot-, vector-, and polygon-generator circuit operation. e Character-generator circuit operation. © Display operation. When the self-test switch (located on the utility panel behind the coin door) is turned on, the game enters the Self-Test Mode. The following self-test displays are arranged in the sequence in which they occur after the self-test switch fs tured on. After Scaccu 10—Sizc and Cenicring, the sequence starts over with Screen 2-Hardware and Switch Test. Turn the self-test switch off then on again to obtain Screen 1-Accounting and Options.

Screen 1—-Accounting and Options The Accounting and Options screen, as shown in Figure 2-1, displays the accounting information and the option settings. The totals in the Accounting section of Screen 1 are those accumulated since the game was first turned on or last reset.

ie eetes, ae Bic r: "LEFE EACH:

Figure 2-1 Accounting and Options

2-2 ‘The following information ie dieplayed in the Accounting section of Screen 1:

  • AUX COINS shows the number of free coins selected hy the auxiliary cain switch in the normal play mode. © PAID COINS shows the total number of coins inserted into both game coin mechanisms.

* GAMES PLAYED shows the total number of free and

paid games played. The number of Doodle City games played appears as D: XX XX on the same line. Add the Doodle City number to the number on the left to Obtain the total games played.

  • AVG GAME TIME shows the average time, in minutes and seconds, of all the games played.
  • TOLAL GAME TIME shows the total time, in hours, minutes, and seconds, of all the games played. © TOTAL TIME ON shows the total time, in hours, minutes, and seconds, the game has been on.

Resetting the Accounting Information. The accounting information can be reset by simultanevusly holding the FIRE button down and pushing the joystick forward. Resetting the High Scores. We suggest that you reset the high-score table aftcr any changes are made to the op tions that may affect the average game time. The high-score table displayed in the Attract Mode can be reset by simultaneously pressing the FIRE and Start 2 buttons. Changing the Options. The Options section of Screen 1 shows the current option-switch settings. The options can be changed by resetting the option switches located on the central-processing unit (CPU) printed-circuit board (PCB). Refer to Chapter 1 for option-switch information. Simultaneously press the Start 1 and 2 buttons to obtain Sereen 2.

Screen 2—Hardware and Switch Test Sercen 2 is divided into two sections: Hardware Test and Switch Test. The Hardware Test section is divided into two segments that show the condition of the ROM and RAM circuits. If the hardware test passes, the message ROM OK will appear in the top segment and RAM OK will appear in the bottom segment as shown in Figure 2-2. If the ROM test fails, the top segment of the Hardware Test section will give the location of the ROM circuit that faued; the bottom segment will be blank as shown in Figure 2-3. Ifthe RAM test fails, the bottom segment will show the following error messages:

NOTE An gscilluscope syne pulse is available to aid in troubleshooting the mathbox and video processor circuits. Perform the procedures described in the following description for the MB ERRORS XX and VP WONT STOP messages.
Page 16

1, RODOT, Sclf or

  • BAD OP indicates that the custom sound IC at location 4E on the CPU PCB has failed.

© —NOIRQS indicates that the interrupt-request circuit on the CPU PCB‘has failed.

WAMDr©VP WONT STOP indicates that the video processor

circuit on the Video PCB has failed.

ee =coiisi) eee

To aid in troubleshooting the video processor circuit with an oscilloscope, press the Start 1 button to obtain

x:FEvi6aScreen 7-Dot, Vector, and Polygon Test. Perform the

REBSHITEN 35: paisa procedure described under Screen 7-Dot, Vector, and

EX,Ceay,:Polygon ‘lest.
Lae)“3t liez*NO VBLANK indicates that the vertical-blanking cir-
RESGSTART1FORRcuit on the Video PCB has failed,

© BADRAM followed by a descriptor, an address, anda

Figure 2-2Hardware Test—Passesbit pattern (e.g., CO 2010 WXX RYY) indicates that

there is a bad address (2010) or bit pattern (WXX RYY) at the RAM indicated by the descriptor (CO). WKX is the bit pattern written to address 2010 and RYY is the bit pattern read from address 2010. An error message with two descriptors and addresses (¢.g., BAD RAM MA 2001 CO 2010) indicates that the two addresses are shorted together. Refer to Table 2-1 to locate the RAMs identified by the descriptor. The RAM locations in Table 2-1 are listed in the order in which they arc tested,

Table 2-1 RAM Locations x: FE

_ronseDescriptorLocationDescription

7 o

ae SHETEH35:7wo2A, 2B,3A,3BWorking RAM (800-FFF
baer‘=Sta(CPU PCB)age 0, O-7FF unpaged)
RegrcoRe™=BERRT2:a
wi2A, 2B,3A,3BWorking RAM (800-
PRESSSTART1FORNEXTSCREEN.(CPU PCB)FEF page 1)
wa2A, 2B, 3A, 3BWorking RAM (800—

(CPU PCB) FFF page 2)

Figure 2-3Hardware Test—FailsMAIN, 1. 2N,2PMath RAM (commu:

(CPU PCB) nication with mathbox)

coIC, 1DCommunication
°EEROM CLEARED indicates that there is a new(ideo PCB)er beanies enon)
EEROM at location 4B on the CPU PCB.a26.25Pann
*EEROM BAD indicates that the EEROM at location 4B(Video PCB)RAM 1 (communication

on the CPU PCB has failed. with video processor)

©)MRERRORS XX indicates that there is either bad dataAL2M, 2NAlphanumerics RAM

oratimcout problem with the Y, P, R, or C functions (CPU PCB) in the mathbox circuit on the CPU PCB. The mathbox will count from 00 to 99 and then repeat. The count will stop when the fault 1s corrected. The Switch ‘Test section of Screen 2 shows the condition ‘To aid in troubleshooting the mathbox circuit, the of the joystick, dual-inline package (DIP) option, coin, mathbox can be pulsed to provide an oscilloscope start, and FIRE switches. The X- and Y-hexadecimal syle signal. Press wie Swart 2 Dunn w pube dic numbus show the horizontal and vertical range of the mathbox. Connect the oscilloscope sync input to pin joystick control. The joystick is electrically centered and 10 on the integrated circuit at location 9L on the CPU checked for the proper horizontal and vertical range in PCR. Press the FIRE button to stop the pulse mode. Screen 4-Toystick Test 2.

2-3

Page 17

Eelf teat

The DIP oprion-switch settings at locatian SE. on the CPU PCB are shown by the top group of eight digits on the right side of the screen. The bottom group of eight digits show the settings of the option switches at location 3J on the CPU PUB. ‘The digits begin with switch 1 on the left and are numbered sequentially to switch 8 on the right (a0 indicates that the switch is off, a 1 indicates that the switch is on). The coin, start, and FIRE switch readouts change color as each switch is pressed to indicate proper operation. Press the Start 1 button to obtain Screen 3.

Screen 3—Joystick Test 1 The Joystick Test 1 screen. as shown in Figure 2-4. displavs the condition of the joystick. Press the FIRE button to start the test. The messages WAIT WHILE TEST OCCURS and DO NOT TOUCH JOYSTICK will appear. The test is completed after 10 seconds. If the test passes, the message GOOD STABILITY will appear and the display will automatically proceed to Screen 4—Joystick Test 2.

If dhe test fails, the message BAD STABILITY will appear to

indicate an unstable joystick circuit. If desired, press the Start 2 button to obtain Screen 4.

parse PYRE" YS BVBhy* repr. -

Gooo STABILITY

PRESS STORE ZeLP gO TO press START xf scREEN.

Figure 2-4 Joystick Test 1

Screen 4—Joystick Test 2 The Joystick Test 2 screen, as shown in Figure 2-5, is used to electrically center the joystick and verify that the control range is within acceptable limits. The message BAD VERTICAL/HORIZONTAL CENTER indicates a faulty joystick or associated circuitry. Repair the fault before proceeding with this test. Move the joystick around its extreme outside mechamcal limits and check that the flashing box draws a continuous dotted frame around the outside of the yellow box. Move the joystick and completely fillin the area inside the dot.

2-4 4 BOBOT

ted frame with dots. Check that the dot pattern is continuous and uniform without gaps. Press the FIRE button to go back to Screen 3—Joystick Test 1, or press the Start 1 button to obtain Screen 5.

prese PIRES Re*teRreg. Ze

Figure 2-5 Joystick Test 2

Screen 5—Sound Test The Sound Test screen, as shown in Figure 2-6, is used to verify that the sound microprocessor and associated circuitry is operating properly. Use the joystick to select the sounds (not all are used during game play). Press the FIRE button to start the sound. Press the Start 1 button to obtain Screen 6.

SOUND TEST

PRESS FIRE TO START SOUND. SELECT SUUBW MLInD SUYSIICK. SOUND NUMBER: 538

PRESS START 1 FOR NEXT SCREEN.

Figure 2-6 Sound Test

Page 18

I,RonoT

ero JKLMNOPGRST

iF Tec EF GHT JKL ANOS EF GH CL

Figure 2-7 Alphanumerics

Screen 6~Alphanumerics The Aiphanumerics screen, as shawn in Figure 2-7, is used to verify that the alphanumeric character-generator circuits are Operating properly. Press the Start 1 button to obtain Screen 7.

DOT VECTOR POLVGON TEST

PRESS FIRE TO SELECT. pot

PRESS START 1 FOR NEXT SCREEN,

Figure 2-8 Dot, Vector, and Polygon Test

Screen 7-Dot, Vector, and Polygon Test The Dot, Vecior, and Polygun Test screen, as SHOWN IN Figure 2-8, is used to verify that the dot-, vector-, and polygon-generator circuits are operating properly. Press the FIRE button to select a dot, vector, or polygon display. Self Toot

To aid in troubleshooting the video pracessor, the video processor can be pulsed to provide an oscilloscope sync signal. Press the Start 2 button to pulse the video processor. Connect the oscilloscope sync input to pin 12 on the integrated circuit at location 4K on the Video PCB. Press the FIRE button to stop the pulse mode. Press the Start 1 button to obtain Screen 8.

Figure 2-9 Color Bars

Screen 38—Color Kars The Color Bars screen, as shown in Figure 2-9, is used to verify that the video circuits are operating properly and. the display is adjusted for the appropriate colors. The display should contain eight distinct horizontal rows of color bars with eight different shade segments in each color bar. Examine the Color Bars display for the following characteristics: ¢ = The eight color bars (from top to bottom) should be white, red, orange, yellow, green, cyan, blue, and purple. Each color bar should contain eight separate segments of progressively lighter shades of the same color. ¢ All of the color bars should have the same relative intensity.

If the preceding display characteristics are not correct, refer ta the Display Mannal fir the appropriate adjustment procedure or to determine the possible cause of failure. Press the Start | button to obtain Screen 9.

be kan

Page 19

Self-Test

Scecen 9-Grid Pattern The Grid Pattern screen, as shown in Figure 2-10, is used to verify that the display linearity and convergence are properly adjusted. Examine the grid pattern for the following characteristics: ¢ — Grid lines should exhibit no pincushioning or barreling and the lines should be straight within % inch.

  • Convergence should not exceed 2.0 mm.

Figure 2-10 Grid Pattern

If the display characteristics are not within limits, refer to the Display Manual for the linearity and convergence adjustment procedures or to determine the possible cause of failure. Press the Start 1 button to obtain Screen 10. 1, RODOT.

Screen 10-Size and Centering The Size and Centering screen, as shown in Figure 2-11, is used to verify that the screen size and centering is within acceptable limits. The displayed frame should be within ¥% inch from the edges of the screen on all four sides. If not, refer to the Display Manual for the size and centering adjustment procedures.

Figure 2-11 Size and Centering

NOTE Press the Start 1 button after Screen 10-Size and Centering, to repeat the self-test sequence beginning with Screen 2-Hardware and Switch Test. If desired, turn the self-test switch

off then on again to obtain Screen ] Account

ing and Options. Do not move the joystick when turning the self-test switch off or on.

Page 20

Maintenance

This chapter includes preventive and corrective maintenance procedures for the Hall-Effect joystick control and the Start and FIRE pushbutton switches. To assure maximum trouble-free operation trom these controls, Atari recommends that periodic preventive maintenance be performed as described in this chapter. If the controls require removal or replacement, refer to the Corrective Maintenance section of this chapter for the recommended procedures. References are made to Chapter 4 Illustrated Parts Lists, 10 aid in locating the parts that are mentioned, but not illustrated, in the following maintenance procedures.

Page 21

Maintenance 1m

Preventive Maintenance

Preventive maintenance includes cleaning, lubricating, and tightening the securing hardware. For maximum trouble-free operation, preventive maintenance should be performed at the intervals specified in Table 3-1.

Table 3-1 Recommended Preventive- Maintenance Intervals

Control Maintenance Interval

Joystick Control Lubricate joystick and tighten securing hardware at least every four months. n FIRE Switches Clean switch contacts and tighten. securing hardware at least every four mon Start Switches Tighten securing hardware at least every six months.

WARNING Tu avoid possible clectrical shock, unplug the game power before performing any preventive maintenance procedures.

Removing the Control Panel

Perform the following procedure to remove the control panel from the cabinet (see Figure 4-2).

  • Turn the game power off.
  • Open the coin door.
  • Reach up through the coin door opening and release the two spring-draw latches located under the control panel on either side of the game cabinct.
  • Grasp the front edge of the control panel and lift just far enough to expose the control-panel harness conneutor.
  • Disconnect the control-panel harness connector and remove the control panel from the cabinet.
  • Replace the control panel in the reverse vider of removal.

Lubricating the Joystick Control

Perform the following procedure to lubricate the Joystick control and tighten the securing hardware (see Figures 3-1 and 4-2). 1, Remove the control panel as previously described.

  • Using a %<-inch hex driver tighten the four nuts securing the joystick assembly to the adjustable mounting plate (see Figure 4-2).
  • Using a Phillips screwdriver tighten the four screws securing the adjustable mounting plate to the controlpanel brackets (see Figure 4-2). 4, Disconnect the four-pin connector from the Hall- Effect printed-circuit board (PCB). § Using a Phillips screwdriver remove the two screws securing the PCB to the Hall-Effect positioner plate.
  • Using a %-inch hex driver remove the four screws securing the lower Hall-Effect housing and positioner plate to the upper housing assembly.
  • Remove the actuator and the X/Y direction slides.
  • Apply a small amannr of lithinm-base grease (part no. 107027-001) to the actuator and X/Y direction slides as shown in Figure 3-1.
  • Apply a small amount of lithium-base grease to the plunger, pivot ball, and actuator ball on the joystick shaft as shown in Figure 3-1. Press the joystick control knob down to compress the spring and expose the contact surfaces of the pivot ball and plunger. 10, Reassemble the joystick as described under Reassembling the Joystick Control in the Corrective Maintenance section of this chapter.

Cleaning the FIRE Switches

Perform the following procedure to clean the FIRE switch contacts and tighten the securing hardware.

  • Kemove the conuol panel as previously described.
  • Using electrical contact cleaner clean the switch contacts. When the FIRE button is pressed, the wiping ac- Ulu Of Wie CLuse Dat Luntacts provides a aclf cleaning feature. Do not burnish the contacts.
  • Usinga ¥-inch open-end wrench tighten the stamped nut sccuring the FIRE switches to the control panel.

Tightening the Start Switches

The start switch contacts are sealed inside the switch housingand do not require cleaning. Tighten the start switches by finuily lividing the black conc shaped bushing on the front of the control panel while turning the switch housing clockwise.

Page 22

TL. ROROT Maintenance

Corrective Maintenance

Corrective maintenance consists of removal, disassembly, reassembly, and replacement of the joystick control, and the Start and FIRE switches.

‘To avoid possible electrical shock, unplug the game before performing any corrective maintenance procedures.

Removing the

Disassembling the ously disassembled, proceed to step 11 Joystick Control

Perform the following procedure to remove the joystick control from the control panel (see Figure 4-2). Refer to Disassembling the Joystick Control for detailed disas- Separate the lower housing and the positioner plate trom the upper housing assembly. Remove the actuator and the X/Y direction slides. Gently press the magnets out of the clips in the X/Y direction slides. Do not drop the magnets.

NOTE The following steps describe the procedure for disassembling the upper housing assembly.

Using a metal punch remove the 0.086-inch roll pin securing the actuator ball to the shaft. Using a metal punch remove the %-inch roll pin securing the pivot ball to the shaft. sembly procedures. . Slide the shaft out of the housing and remove the 1, Remove the control panel as described in the Preven- plunger and spring from the shaft. tive Maintenance section of this chapter. Disconnect the four-pin connector from the Hall- Reassemble the joystick control as described in the following procedure. Effect PCB.

  • Usinga %.-inch hex driver remove the four nuts secur-

ing the joystick control to the adjustable mounting Reassembling the

plate. Joystick Control

  • Carefully lift the joystick control from the adjustable mounting plate.
  • Replace the joystick control in the reverse order of removal. Perform the following procedure to reassemble the joystick control (see Figure 3-1).
NOTE . . Ifthe upper housing assembly was not previ- Disassembling the ously disassembled, proceed to step 11.

Perform the following procedure to disassemble the 1. Slide the disc onto the ball-handle shaft. joystick control (see Figure 3-1), If necessary, remove the 2, With the close-wound coils toward the end of the joystick control from the cabinet as previously described. shaft, slide the spring onto the ball-handle shaft. 3, With the bell-shaped end toward the end of the shaft, slide the plunger onto the ball-handle shaft and over the spring. 4, Slide the end of the ball-handle shaft through the top of the lower Hall-Effect housing.

  • Slide the pivot ball onto the ball-handle shaft andalign the hole in the shaft (nearest the lower housing) with the hole in the pivot ball.

6. Using metal punch insert the 4-inch roll pin through

  • Using a 4-inch hex driver remove the four screws the pivot ball and the hal-handle shake. securing the Hall-Effect positioner plate and lower 7. With the beveled edge toward the pivot ball, slide the Hall-Effect housing to the upper housing assembly. actuator ball onto the end of the ball-handie shaft.
  • Using a Phillips screwdriver remove the two screws securing the Hall-Effect PCB to the positioner plate.
CAUTION The position of the Hall-Effect sensors on the Hall-Effect PCB is critical. Avoid bending these sensors when handling the PCB.

3-3

Page 23

Maintenance

12.

1B.

14.

16.

19. Align the nole in the actuator ball wit dic huie in thie end of the ball-handle shaft. Using a metal punch insert the 0.086-inch roll pin tuvugh the actuator ball and the ball-handle shaft. . Lift the disc, tilt the ball-handle to one side, and apply a small amount of lithium-base grease (part no. 107027-001) to the contact area between the plunger and the upper housing as shown in Figure 3-1. . Place the lower Hall-Effect housing over the ballhandle shaft and align the four screw holes in the upper housing with those in the lower housing. ‘With the marked end of the magnet toward the + emassed an the Hall-Effect X-direction slide, insert the magnet into the slide clip. Apply a small amount of lithium-base grease to the two tab pins and the four corners of the X-direction slide as shown in Figure 3-1. Place the X-direction slide on the lower Hall-Effect housing. Make sure the two tab pins are aligned with the housing slots and that the magnet is facing the small (1 embossed in the outside edge of the housing. . With the marked end of the magnet toward the + embossed on the Hall-Effect Y-direction slide, insert the magnet into the slide clip. Apply a small amount of lithium-base grease to the two tabs and edges of the ¥-direction slide and to both sides of the actuator as shown in Figure 3-1. With Ue magnct facing the smalt_ A embossedon the edge of the lower housing, place the ¥-direction slide on top of the X-direction slide. With the beveled hole toward the lower housing, place the actuator over the ball-handle shaft and through the center of the X- and Y-direction slides. Make certain the actuator is inserted through both slides so that the end of the ball-handle shatt is flush with the end of the actuator. Gently place the Hall-Fffect positioner plate over the slides so that the magnets and two taps on the ~ 20.

21.

or

23. direction slide are aligned with the correspanding slots in the positioner plate. Adjust the positioner plate until the four screw holes are aligned with those in the lower housing. Insert the four 2% -inch self-tapping screws into the four screw holes in the positioner plate. Using a %4-inch hex driver tighten the four screws to 15 in/lbs +2 in/Ibs. Check that the ball-handle returns freely to the centered position. Check thar the two Hall-Effect sensors on the Hall- Effect PCB are perpendicular to the PCB. Place the PCB on the positioner plate so that the sensors are positioned in front of the rwo magnets installed in the Slides. Using a Phillips screwdriver tighten the two '4-inch self-tapping screws securing the Hall-Effect PCB to the positioner plate.

Removing the Start Switches

Perform the following procedure to remove the start switches from the control panel (see Figure 4-2).

L Remove the control panel from the cabinet as described in the Preventive Maintenance section of this chapter. Disconnect the wires from the start switch terminals. Firmly hold the black cone-shaped bushing located on the outside of the control panel and turn the switch housing on the inside of the control panel counterclockwise. Replace the start switches in the reverse order of removal. Refer to Figure 4-2 for the proper wire connections.

Removing the FIRE Switches

Perform the following procedure to remave the FIRE leaf switch contacts and pushbutton assembly from the control panel (see Figure 4-2), Remove the control panel from the cabinet as described in the Preventive Maintenance section of this chapter. Disconnect the wires from the leaf-switch terminals. Using a Phillips screwdriver remove the screw securing the leaf-switch contacts to the pushbutton assembly. Usinga %-inch open-end wrench remove the stamped nut that secures tne pushbutton assembly w Wie woe trol panel. Replace the leaf-switch contacts and pushbutton assembly Im the reverse Uider Uf ccmoval.

Page 24

1, RODOT, Maintenance

Lower Housing Embossed Triangle \ hy

Ball Handie %Direction Slide > |

Marked End

| Embossed + Embossed Triangle

¥-Direction Slide ——>| Close-Wound End

Actuator f a

| i Upper Housing

Positioner Plate

ae i) a— Yeinch Pin Rie 2%-Inch Self-Tapping Screw (IS

Pivot Ball A . rhs.

%a-Inch Selt-Tapping Screw Leh 0.086-Inch Pin

“Actuator Ball

4 Lubricate with lithium-base lubricant (part no. 107027-001)

Hall-Effect PCB

Figure 3-1 Lubricating, Disassembling, and Reassembling the Hall_Fffect Joystick

Page 25

Illustrated Parts Lists

‘This chapter provides information you need to order parts for your game. Common hardware (screws, nuts, washers, etc.) has been deleted from most of the parts lists. However, a parts list is included for the hardware to mount the printed-circuit boards (PCB) to the cabinet. The PCB parts lists are arranged in alphabetical order by component. Each component subsection is arranged alphanumerically by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598through approximately 201000-. When ordering parts, please give the part number, part name, number Of this manual, ana serial number oF your game, This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. The Atari Customer Service numbers are listed on the inside front cover of this manual.

Chapter 4

Page 26

Tihictrated Parts 1 ists P BOURE EY

041249-01 Upper Reiaine: 041255-01 Auwautiun Panel oatzg0 of Attraction Film wiGraphics

006008-05 Molding, Video Display Assy + ee Fiucresoent Tbe See Service Manual & Speaker Assy See Figure 4-5 a 0414256-1715, a —_ H-Shaped Retainer 041130-01 041261-01 Lelt Speaker Grile fy Bevel 041250-01 Lower Retainer

Control Panel Assy See Figure 4.2 Hall-Ettect Joystick Assy See Figure 4-3 178013-001 Latch

042608-01 Cover Plato

036130-01 Lower Speaker Grille

041647-01 Display Shield 148002-002 Speaker

006008-04 Molding

041130-02 Right Speaker Grille

. ; : Utility Panet Coin Door See ore 44 See Figures 4.6 & 47

4149.02 038870-01 Right Corner Extrusion Coin Box Enclosure Coin Box 041649-01 Left Corner Extrusion

Figure 4-1 Cabinet-Mounted Assemblies A042600-xx A

4-2

Page 27

1, ROBOT Ulustrated Parts

‘Game Dooumentation— See parts list on next page

ADA2601-xx Cabinet Assembly

178034-024 T Molding

EMI Cage See Figure 4.8

041240-01 Head Access Panel

Switching Power Supply Assy See Figure 4-8 and Service Manual

Game PCBs + See Figures 4-9 & 4-10

034536-09 Foam Pad EMI Shield PCB

See Figures 4-8 & 4-11

A03881-01 Lock A042627-01 Power Harness

178093-001 A042625-01 Fan Blade Guard Main Harness

171063-001 Fan ~~ 041630-02 Body Access Panel

00999201 On/Oif Swatch Cover 1 d ‘A040587-01 a Power On/Oft Switch 78-3201 037332-01 Adjustable Glide Ventilation Grille

A4094690-01 RFI Filter Assy A042606-01 A040586-01 178034-024 Pedestal Access Panel Assy Power Cord TMoiding

Figure 4-1 Cabinet-Mounted Assemblies, continued A041600-xx A

Page 28

Ulustrated Parts Lists TRONS

Cabinet-Mounted Assemblies Parts List

Part No. Description US-Built Cabinet A042601-01 ‘Cabinet Assembly—consists of A041606-01 Pedestal Assembly 04160701 Head Assembly A042602-01 Body Assembly Ireland-Built Cabinet A042601-02 Cabinet Assembly—consists of ANAIENG.01 Pedestal Assembly ‘404160701 Head Assembly A042602-01 Body Assembly US- and Ireland-Built Cabinets A038074-07 Switching Power Supply (see service manual TM-261) A040586-01 Strain-Relief Power Cord A040587-01 Power On/Off Switch, Harness, and Mounting Plate Assembly A034630-01 RFI Filtci Assciubly A042606-01 Rear Access Panel Assembly for Pedestal—consists of A038881-01 Lock (Acceptable substitute is part no. A038881-03) 041655-02 Rear Avcess Paricl 037332-01 Ventilation Grille A042625-01 Main Harness 042627-01 Power Harness 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive ‘lape 4-Inch Wide x Inch Thick (36 inches required; used along top and bottom edge of display shield—not shown) The following seven items are technical information supplements to this game: T™.251 1, ROBOT Operators Manual with Illustrated Parts Lists SP-251 1, ROBOT Schematic Package ST-251 1, ROBOT Label with Self‘fest Procedure and Option Switch Settings TM-160 Service Manual for 19-Inch Electrohome Display (Display not shown—use with part no. 92-049) TM-210 Service Manual for 19-Inch Disco Display (Display shown in illustration—use with part no. 139003-106) T™M-220 Service Manual for 19-Inch Matsushita Display (Display not shown—use with part no. 39003-1004) ‘TM-261 Switching Power Supply Service Manual 006008-04. Display Shield Extruded Plastic Molding, 009992-01 On/Off Switch Cover 03453609 Linch Thick Foam Pad (located between the Power Supply PCB and the cabinet wall) 036130-0L Lower Speaker Grille 038091-01 Molded Coin Box

038870-01Coin Box Enclosure(not shown)
041130-01Left Speaker Grille(metal extrusion)
041130-02Right Speaker Grille(metal extrusion)

041240-01 Rear Access Panel for Head Assembly 041250-01 Display Shield Lower Retainer 041255. Attraction Panel 041259-01 Semi-Rigid Attraction Film with Graphics (not shown)

(continued on next page)

Page 29

1, ROBOT Mustrated Parts Tiers

Cabinet-Mounted Assemblies Parts List, continued

Part No. Description

041261-01 Video Display Bezel 041630-02 Rear Access Panel for Body Assembly (includes lock) 04164701 Display Shield 041649-01 Left Comer Extrusion 041649-02 Right Corner Extrusion 042608-01 Cover Plate 148004-002 5-Inch, 4-Ohm, 6-Ounce Shielded High-Fidelity Speaker (located below control panel) 171063-001 110 V, 60 Hz Exhaust Fan 178013-001 Spring-Draw Latch (not shown) 178034-024 %4-Inch Black Plastic FMolding (21 inches required on front of pedestal base; 168 inches required on the side panels of the head assembly; 104 inches required on the side panels of the body assembly; 94 inches required on the front panel of the body assembly) 178093-001 Guard for Fan Blade 179125-001 Grounding Clip on Main Harness (not shown)

Page 30

Eger Allustrated Parts Lists

75-9910W0 Stamped Nut Players may receieve an electrical shock 75-5116B if this control panel is not properly 033127-01 160013-001 Molded Switch Bezel Carriage Bott grounded! After servicing any parts on Leat Switch/Button Holder the panel. make sure that the grounding clipis secured to the metal tab on the inside of the control panel.

178030-003 Pushbutton Acey

92-039 LED Switch

042582-01 Gentror rane!

T5-9910N0 i Stamped Nut a " ‘ 042609-01 Panel Plate

, 179125-001 27 Grounding Cip

Flat Washer 75-0408 Split. Lock Washer

042613-01 Player-Option Decal i . 1 : : A042628-01 042615-01 Harness Assy Center Decal

042614-02 042015-04 Lett Decal Right Decal

042610-01 Mounting Bracket

AD40995-01 Hall-Effect Joystick Assy See Figure 4-3

Figure 4-2 Control Panel Assembly A04Z603-01 A

Page 31

4 ROBO? Ilustrated Parts Lists

Black 2-Player Start 1-Player Start Yellow Black (Common) Orange (Open) Yellow Brown (Open) Black (Common) a

Right FIRE Button Left FIRE Button White/Black Red + White Red +

NOTE The orientation ofthe 1-and 2-olaver stant switches may vary.

Figure 4-2 Control Panel Assembly, continued Parts List

Part No. Description A040935-01 Hall-Effect Joystick Assembly A042628-01 Control Harness Asscmbly 03312701 Black Molded Switch Bezel 042582-01 Formed Control Panel 042609-01 formed Pancl Plate 042610-01 Adjustable Mounting Bracket 042613-01 Player-Option Decal 042614-01 Left Decal 042614-02 Right Decal 042615-01 Center Decal 160013-001 Leaf Switch with Button Holder 178090-003 Diack Pustibution Asounbly 179125-001 Grounding Clip 62-039 SPDT Momentary Pushbutton Start Switch with Red LED 721012F #10-32 x %4-Inch Cross-Recesscd Machine Screw 75-0108 #10 Flat Washer 75-0408 #10 SplitLock Washer 75-9415 #10-24 Hex Locknut 75-SU2B #10-24 x ¥%-Inch Black Carriage Bolt 75-9910NO $-Inch x Ll Stamped Nut 75-9910W0 "%a-32 Stamped Nut

Page 32

Ulustrated Parts Lists se YE

039721-01 Lower Housing ~,

039713-01 > am Oe

| \ 041283-01 i Magnet 039720-01 040904-01 X-Direction Slide Ball Handle

1 041512-01

039718-01 ¥-Direction Slide Spring

039712-01 Plunger

A040932-01 Upper Housing Assy

039722-01 Upper Housing PP ty) 039711-01 Positioner Plate

73-20814 Yelncn Pin

a040280-01 Hall Effoct PCR. 039716-01 Pivot Ball

il ' - 73-20509 ; Q086-Inch Pin Tev0z-140 a >= Screw 176030-104 : 040699-01 ‘Screw ' Actuator Ball

Figure 4-3 Hali-Effect Joystick Assembly A040935-01 A

~ &

Page 33

1, ROBOT

Hall-Effect Joystick Assembly Parts List

Part No. Description A040341-01 Hall-Effect Printed-Circuit Board 4040932-01 Upper Housing Joystick Assembly—includes 039712-01 Plunger 039713-01 Disc 039716-01 Pivot Ball 039722-01 Upper Housing 040304-01 Joystick Ball Handle 040693-01 ‘Actuator Ball 040705-01 Compression Plunger Spring 73-20509 0.086 x %-Inch Roll Pin 73-20814 % x Jnch Roll Pin 03971 xx Positioner Hall-Effect Plate 039715-01 Actuator 039718-01 Y-Direction Slide 039720-01 X-Direction Stide 03972101 Lower Microswitch Housing 041283-01 0.125 x 0.625 Magnet 176602-140 #8-16 x 2%-Inch Hex Head Self Tapping Screw 176030140 #420 x %4-Inch Pan Head SelfTapping Screw

Page 34

Ilfustrated Parts Lists 1, ROBOT.

NOTE Only the |reland-Built cabinethas two. coin counters. A038004-01 ve ‘ Hames A002465-01 i Coin Counter a

038003-01 7 Panel

62-041 Auxiliary Con Switch

49-9032 Volume Control

176018-002 screw 69-001 SelfTest Switch 178070-001 volume Gunigul ROUl

WARNING Before removing or repairing the utiti- 179125-001 Grounding Cin ultity panelisnotproperty grounded! After servicing any parts on the panel, make sure that the ground wires firmly attached to the back of the coin counter.

Figure 4-4 Utility Panel Assembly A038002-01 H Parts List

Part No. Description A002465-01 6¥ Coin Counter 403800401 Utility Pane! Harness 19-9032 Volume Control 62-041 SPDT Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap 69.001 DPNT Selflast Switch 75-9168, 6-32 Hexagon Machine Nut 75-9910W0 "4-32 Stamped Nut 038003-01 Utility Panel 176018-002 #632 x ¥4-Inch Thread Forming Pan-Head Screw 178070-001 Volume Control Knob 179125-001 Grounding Clip

Page 35

1.ROROT sllustrated warts Lists

(9-S61816P- St poole aker Harness oe Wire Nut , 04125201 ra 179035-00 GrileBracket qeeticdes 041325-01 Ballast Shield 179035-001 Tube Holder 99.1006 Tab A005493-01 Tube Harness

148004-002 ‘Speaker 03/469-01 Bracket

Wire Colors for Speaker Violet 041241-02 Yellow Pane} 142028-001 Transformer

NOTE To ensure that the fluorescent tube starts, make sure the ground wire is. firmly attached to both the ballast transformer and the steel tube bracket.

Figure 4-5 Fluorescent Tube and Speaker Assembly A041320-01 A Parts List

Part No. Description A005493-01 Fluorescent Tube Harness Assembly A037540-01 Ground Wire with Grounding Clip A041342-01 Speaker Harness Assembly 70-304 18-Inch. 15.Watt. Coal White Finarescent Tihe 79-561816P Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-1003, Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (consists of two pierces) 99-11009 Starter Socket 037469-01 Steel Tube Bracket 041241-02 Wood Mounting Panel 041252-01 Speaker Mounting Grille/Bracket 041325-01 Ballast Shield 14202801 60 Hz, 118 V, Rallast Transfinemer 148004-002 $-Inch Diameter, 5 W, 4 Ohm, Shielded Speaker 179035-001 2-Pin Fluorescent Tube Holder 179125-001 Grounding Clip (Acceptable substitute is part no. 179174-010)

Page 36

Musa Paris Lists 1, ROBOT

99-10140 Panel Asseiibly 75-9488 Locknut 99-10116 Lever 99-10152 Right Coin Inlet ‘i 99-10147 Hgtawss: 171006-035 Coin Mechanism

75-9448 Locknut

99-10096 Fastener,

99-10151 Lef Coin Inlet

99-10080 Lamp Sooket

72-94008 rew

99-10" Bar Retainer

99-10042 thru 99-10045. Sw BR4

Ne Cuin Switch Assembly 910190 SS Switch Cover 99-10154 Bracket Assembly

99-10068 Coin Chute

r Coin Switch

99-10075 thru 99-10078 ‘Switch Wires: 99-0008 Retainer 7514128

Screw

Figure 4-6 Coin Controls, Inc. Coin Door Assembly 171034-xxx A

Page 37

1, ROBOT Mlustrated Parts Lists

99-10148 Lock Assembly

99-10142 Button Housing a 72-HAI404C Screw

99-10134 99-1019 Cover s9t0199 Pa Button Assembly | 90-10110 Button : ON 99-1015, a9-10140 ong Lock Assembly

99-10145 Cam nN : ; 99-1041 _ | Coin Return Cover g ® i : | 99-1017 ‘ 4 r een Coin Return Door

72-JA1405B Screw, _ j——— 99-10144 Channel Clip. a 99-15066 Screw

99-10149 Service Door

038081-.09 Coin Box

99-10143 Frame

Figure 4-6 Coin Controls, Inc. Coin Door Assembly, continued 171034-xxx A

4-13

Page 38

Tusuaicd Pane Lisi a Rorcee

Coin Controls, Inc. Coin Door Assembly Parts List

PartNo. Description A036597-01 Harness Assembly (Ireland-built cabinet only) A037542-01 Harness Assembly 7214145 #4-40 x Jp-Inch Cross-Reeessed Pan Head Steel Machine Screw 75-056 #6 InternalTooth Zinc-Plated Steel Lock Washer 75-148 #4-40 Steel Machine Hex Nut 75-34148 #440 x J Inch 62° Cross-Recessed Flat Head Stecl Machine Serew 99-15001 Coin Return Button with U.S. 25-Cent Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 9915003 ‘Coin Rutuin Dutton with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Plate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008 Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Return Button with British 10 Pence Price Plate 9915010 Coin Return Button with Australian 20-Cent Price Plate 99-15011 Coin Return Button with Ialian 100 Lire Price Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Ialf of Coin Inict 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 9915029 ‘Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 9915039 Mctdl Bezel for Guin Return Buon 99-15042 Coin Switch for U.S. 25 Cents 99-15052 Spring for Coin Return Button 99-15055 Retaining Screw 99-15056 #4-40 x Yq-Inch Cross-Recessed Pan-Head Steel Machine Screw 9915060 Switch Cover 99-15063 Screw for Hinge 9915066 Screw for Chanp 99-15067 Lock Assembly 99-15070 Doors and Frame PPAIOT! Clamp for Pac 99-5072 Door Frame 9915073 Upper Door 995074 Lower Door 99-15075 Switch Adjuster 99-15083, Base Plate—includes: 99-15040 Lever 9915054 Pivut for Lever 038091-01 Coin Box—not included in assembly (Acceptable substitute is part no. A037491-01) 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 1 /UU5-U95 Mev Guts Mecsas 171050-001 ‘Dual Entry Face Plate 179047001 Lamp Base

Page 39
  • ROROT Mlusuated Pats Lists

170000-001 9915026 Lamp Coin Inet 170047001 Lamp Base 99-15023 Base Plate

99-15056 Screw for Bezel 9915040 NN. Lever s9-19029, Coin inlet Ne NN 99-15054 Pivet for Lover

99-15055 Retaining Screw NY a

75-9148 Hex Nut ae,

Pa 99-15028 75-056 Coin Return Bux Lock Wash.

99-15056 99-15027 Coin Return Box Screw tor Bezel

99-1079 ‘Sw. Adjuster

99-15060 ‘Switch Sw. Cover 75-3414S Screw

72-1414S Screw

Figure 4-7 Coin Acceptors, Inc. Coin Door Assembly 171027-001 A

Page 40

M.ustrated Parts Lists LRG:

YES 9915052 ye-ipuey Sonng for Button Lock Assy

<“ 99-15038 Bezel for Button

99-15001 thru 99-15011 Return Button

Ab27642 01 Harness—not srowr

99-15039 Bezel for Cover

036091-01 Coin Box

99-15073 Upper Door SOAGOTA 99.1% LowerDoor | Doovse 99-15072 Door Frame

171034-001 — U.S. 25¢/25¢ Coin Door 171034-003 — Canadian 25¢/25¢ Coin Deo 171034-005 — U.K, 10 P/50 P Coin Door 471034-006 — U.K. zu P90 P Goin Boor 171034-009 — German 2 DM/1 DM Coin D0. 171044-010 — German 2 DM/5 DM Coin Doct 171084-011 — German 1 DM/5 DM Coin Doc! 171034015 — French 2 Frit Fr Cola Door

Figure 4-7 Coin Acceptors, Inc. Coin Door Assembly, continued EMOZTOOR &

Page 41

Lpasor

Coin Acceptors. Inc. Coin Door Assembly suustrated Farts tase

Parts List

Part Na. Deceriptian 65-441C Coin Switch 70-11-47 Miniature Bayonet Lamp 72-94065 #4-40 x %-Inch Truss-Head Screw 72-HA1404C #4-40 x 4-Inch Pan-Head Screw 72-JA1405B #4-40 x .32-Inch Pan-Head Screw 75-14128 #4-40 x 44-Inch Pan-Head Screw 73-9448, #4-40 Locknut 99-10008 Retainer 99-1042 Coin Switch Assembly for Belgian 5 Fr and US. $.25 99-1043 Cain Switch Assembly fir German 1 DM, Japanese 100 Yen, Swiss 1 Er 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045, Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068, Coin Return Chute

99-10075,Switch WireUncluded :n coin switch assembly 99-10043)
9910076Switch Wire(included in coin switch assembly 99-10042)
9910077Switch Wire(included in coin switch assembly 99-10044)
99-1078Switch Wire(inchided in coin switch assembly 99-10045)

99-10080 Lamp Socket 99-10081 Key Holder 99-10096 Fastener 99-10104 Bar Retainer 99-10105 Bar 99-1015 Spring 99-1016 Plastic Coin Return Lever 99-10117 Steel Coin Return Door 99-1018, Amber Coin Return Button 9910119 Amber Coin Button for US, $.25 9910144 Coin Botton Cover 9910139 Coin Door 99-10140 Coin Door Inner-Panel Assembly 9910141 Die-Cast Coin Return Cover 9940142 Die-Cast Button Housing 9910143 Coin Door Frame 99-10144 Channel Clip 99-10145 Cam 99-10147 Harness 99-10148 Lock Assembly 99-10149 Service Door yrVIDU witch Cover 99-10151 Left Coin Inlet 9910152 Right Coin Inlet 99-1015 Coin Retuen Box 99-10154 Bracket Assembly 99-15066 Screw for Clamp 038091-01 Coin Box 171006-055 Metal Cuin Mechautsin for U.S. §.25 177010-238 #8-32 Hex Locknut

Page 42

Mtuotrnted Parts Lises 2 moe

NOTE For US-buit gamesthe FCC requires thal the game printed-circuil boards be housed in the EMI cage with the EMI Shicld PCB attached Screw 179125-001 Grounding Clip

A042083-21 |, ROBOT Video PCB

A042561-02 EMI Cage

175004-708 Fiber Washer

176015-112 ae 034536-09 Foam Pad

A039508-21 1, ROBOT CPU PCB.

178044-242 Grommet Pic A040990-01 Washer EMIShield sresas-a48 and Dual PCB Assy ‘A037667-02 Fastener EMI Shield PCB See Figure 41

ing Power Supply ‘See Service Manual

AQ20R71.01 |, ROBOT End PCB.

~ 72-1404F Screw

A042683-21 |, ROBOT Video PCB —___ |

72-1604F Screw A039568-21 |, ROBOT CPU PCD

Figure 4-8 Printed-Circuit Board Mounting Hardware (US & Ireland)

Page 43

1, ROBOT Alluctrated Paete Licte

7216208 176015-112 Screw ‘74-5608NN 041646-0t Spacer Bracket 79-99916 a Assy

‘A03G871-01 __ End PCB

175004-708 Flat Washer

094536-02 Foam Pad 175004-706 Washer

A039568-21 1, ROBOT CPU PCB

A042683-21 |, ROBOT Video PCB.

Figure 4-8 Printed-Circuit Board Mounting Hardware (Ireland), continued

Parts List

Part No. Description

US-Built Games A042561-02 EMI Cage Assembly: aganggn.a1 FMI Shield and Dual Printed-Circuit Board Assembly A037667-02 EMI Shield Printed-Circuit Board Assembly 179125-001 Grounding Clip 178045-442 Snap-In Fastener 178044-242 Grouuuct 175009-221 Plastic Washer 37873-01 Printed-Circuit Board Spacer 72-1604F #632 x %4-Inch Cross-Recessed Steel Screw 72-1404F #440 x \4-Inch Cross-Recessed Steel Screw Ireland-Built Games 175004 706 46 Fiber Washer 74-5608NN #6 x %-Inch Spacer 75-99516 #6-32 Nut/Washer Assembly 72-1620S #6-32 x 1% -Inch Cross-Recessed Pan-Head Steel Screw OA1G 16-01 Printed.Cireuit Board Mounting Rracket 034536-02 ¥%-Inch Foam Pad US- and ireland-Built Games AU42683-Z1 1, ROBOT Videu Piincd-Circuit Board A039568-21 {, ROBOT CPU Printed-Circuit Board A039871-01 I, ROBOT End Printed-Circuit Board 4038074-07 Switching Power Supply 176015-112 #10 x %-Inch Cross-Recessed Pan-Head Screw 175004-708 #8 Flat Fiber Washer 034536-09 1-Inch Foam Pad

Page 44

Ilustrated Parts Lists 1, ROBOT

4-20 Figure 4-9 I, ROBOT CPU PCB Assembly A039568-21 A q]

iphdeinht toizAoos]
a Nemeeri cee
aEbsFie

4 ‘aoeeee co a

ty;5Zz2a

ef BY...

a aszzex1
Page 45

1,nopoT illustrate Farts £ 16%

Figure 4-9 I, ROBOT CPU PCB Assembly, continued A039568 21 A

4-2]

Page 46

Musteated Parts Lins

I, ROBOT CPU PCB Assembly Parts List

NesignatorDescriptionPart No.

Capacitors

ca0.1 pE, 25 V, Ceramic Capacitor122006-104
20.01 pF, 25 V, Ceramic Capacitor1Z2005-103
C3-C70.1 pF, 25 V, Ceramic Capacitor122006-104
C8, C90.22 aE, 25 V, Ceramic Capacitor122006224
c10-C300.1 pr, 25 ¥, Ceramic Capackior1Z22UU6-104
C310.47 uE, 50 V, Electrolytic Capacitor122006-224
C32, C33100 zF, 50 ¥, Electrolytic Capacitor124001-107
C34-Cl1099.1 wR, 25 V, Ceramic Capacitor122006-104

Diodes

CRLType-IN758 Diode32-IN758
CR2‘Type-MV5053 Diode38-MV5053,

Electronically Programmable Read-Only Memories

1A‘Type-27128-4 EPROM Integrated Circuit136029-105
1BType-27120-4 EPROM Integrated Circuit136029106
1c/D‘Type-27128-4 EPROM Integrated Citcuit136029-107
IDEType-2764-4 EPROM Integrated Circuit136029-108
Ic/E‘Type-27120-4 EPROM Integrated Circuit136029-109
1K‘Type-27128-4 EPROM Integrated Circuit136029-110
WK‘Type-2764-2 EPROM Integrated Circuit136029-103
1KALType-2764-2 EPROM Integrated Circuit136029-104

Integrated Circuits

20D‘Type-7418273 Integrated Circuit37-7418273,
2D-2F‘Type-74LS244 Integrated Circuit377418244
2H‘Type-7418245 Integrated Circuit37-7418245
a‘Type-74LS244 Integrated Circuit377418244
2K, 2LType-74L5245 Integrated Circuit37-TALS245,
2M‘Type-7415374 Integrated Circuit37-7418374
3C0/D‘Type-74L5245 Integrated Circuit377ALS245
3E68BO9E Microprocessor Integrated Circuit137249-120
3H‘Type-74LS244 Integrated Circuit37-74L8244
3K‘Type-74832 Integrated Circuit3774832
31, 3M‘Type-748253 Integrated Circuit137248-001
3N‘Type-74S08 Integrated Circuit37-74808
3P‘Type-7418244 Integrated Circuit377418244
4A‘Type-7415139 Integrated Circuit377418139
4BX2212 Integrated Circuit137288-01
ACADC0809 Integrated Circuit137243-001
4ECustom Integrated Circuit1373244221
4HType-74L8244 Integrated Circuit37-7418244
4g‘Type-74LS04 Integrated Circuit37741804
415K2901-C Transistor Array Integrated Circuit137340-001

4-22 soonest sas

Page 47

LROBOT

I, ROBOT CPU PCB Assembly Mlucteated Parte Licte

{continued on next page) Parts List, continued

DesignatorDescriptionPart No.
465L2901-C Transistor Array Integrated Circuit137340-001
415M2901-C Transistor Array Integrated Circuit137340-001
45M2901 C Transistor Array Integrated Circuit137340-001
4PType-748182 Integrated Circuit37-74S182
5AType-74L500 Integrated Circuit37-74LS00
3B‘Type 7A1S139 Integrated Circuit37-74L5139
5cType-741574 Integrated Circuit37-74LS74
sD‘Type-7418139 Integrated Circuit37-7418139
5)Type 71822 Integrated CircuitDT 74592
SFType-74804 Integrated Circuit3774804
6AType-741514 Integrated Circuit37-74L814
6B‘Type-74L504 Integrated Circuit37-74LS04
6CType-74LS11 Integrated Circuit137016-001
6D‘Type-74LS74 Integrated Circuit37741874
6EType-74L8244 Integrated Circuit37-7ALS244
oF‘Type 74874 Integrated CircuitST TAS 74
6}, OK‘Type-74LS245 Integrated Circuit37-74LS245
6HType-74L8273 Integrated Circuit377ALS273
6L.Type 746163 Integrated Circuit37745163
A‘Type-74L890 Integrated Circuit37741890
7B‘Type-74L32 Integrated Circuit37 7ALS32
7C, 7DType-74LS139 Integrated Circuit37-7415139

7E ‘Type-741S163A Integrated Circuit 37-7ALSI63A

TFType-745189 Integrated Circuit37-74S189
7H, 7]Type-745169 Integrated Circuit37-748189
7K‘Type-741S163A Integrated Circuit37-74LS163A
7LType-748163 Integrated Circuit37-748163
BAType-74S32 Integrated Circuit37-74832
8B‘Type-74LS139 Integrated Circuit37-74LS139
BC‘Type-741532 Integrated Circuit37-74LS32
8D‘Type-74LS08 Integrated Circuit37-74L808
SE‘Type-74892 Integrated CircuitSPTASSZ
8F‘Type-74804 Integrated Circuit3774504
8H‘Type-74L5125 Integrated Circuit37-74LS125
oo‘Ty pe“ 7419240 Tu yiatcd ChuteAD /Z314A
8K‘Type-74LS83 Integrated Circuit37-74L883
8LType-745163 Integrated Circuit37748163
on‘Type-74574 Integrated CircuitSP TASTA
9B‘Type-74LS00 Integrated Circuit37-74LS00
oC‘Type-741S04 Integrated Circuit37741804
9D‘Type-741892 Integrated CircuitSPTALSSZ
9‘Type-74S08 Integrated Circuit37-74508
OFType-745163 Integrated Circuit37-74S163
9H, 9‘Type-741583 Integrated Circuit37-741883

4-23

Page 48

Hlustrated Parts Lists

I, ROBOT CPU PCB Asscubly 1, ROBOT

Parts List, continued

DesignatorDescriptionPart No.
9K‘Type-74LS273 Integrated Circuit37-74L8273
oktype: /4L51 /4 Integrated CircuitSF TALSIT4
10AType-74L$86 Integrated Circuit377ALS8O
10B‘Type-74532 Integrated Circuit37-74S32
OC‘ype- /4L3U8 Integrated CircuttS7-7ALSOB
10DType-74532 Integrated Circuit3774832
10EType-7415125 Integrated Circuit37PALSI25
10F‘Type-74S10 Integrated Circuit37-74810
10H-10KType-7418244 Integrated Circuit37-741S244
10L‘Type-7415273 Integrated Circuit37-74LS273
10M‘Type-74LS151 Integrated Circuit37-7ALSISE
10N“Type-74S00 Integrated Circust3774500
10P‘Type-74804 Integrated Circuit37-74804
1B‘Type-741S32 Integrated Circuit37-741532
uc‘Iype-LM424 Integrated Circuit37LM524
uD‘Type-74LS10 Integrated Circuit37-7ALS1O
IE‘Type-741583 Integrated Circuit37-74LS83

Programmable Kead-Unly Memories (PKUM)

5P82HS137 PROM Integrated Circuit136029-112
6M82HS137 PROM Integrated Circuit136029-113
6N82HSI37 PROM Integrated Circuit136029-11
OP82HS137 PROM Integrated Circuit136029-116
7™82HS137 PROM Integrated Circuit136029-121
7NR2HS147 PROM Integrated Circuit136029-114
7P82HS137 PROM Integrated Circuit136029-123,
8M82HSI37 PROM Integrated Circuit136029-117
aNR2HSI37 PROM Integrated Circuit136029-115.
8P82HS137 PROM Integrated Circuit136029-19
OM82HSI37 PROM Integrated Circuit136029-120
ON82HS137 PROM Integrated Circuit136029-118
opR2HS1A7 PROM Integrated Circuit136029-122

Random-Access Memories (RAM)

IN‘Type-6116-2 RAM Integrated Circuit137211-120
wwType-OUlG-2 RAM Inegiaicd Chute197211120
2N‘Type-G116-2 RAM Integrated Circuit137211120
2P‘Type-6I16-2 RAM Integrated Circuit137211-120
2A, 2B‘Type-616 RAM Imegracd Ciicuit137211-001
3A, 3B‘Type-G116 RAM Integrated Circuit137211-001

, Read-Only Memories (ROM)

Wg‘Type-23128-2 ROM Integrated Circuit136029-101
ILM‘Type-23128-2 ROM Integrated-Cirewit136029102

(continued on next page}

Page 49

1,ROBOT Illustrated Parts Lists

J, ROBOT CPU PCB Assembly Parts List, continued

DesignatorDescriptionPart No.

Resistors

RI3302, +5%, 4 W Resistor110000.331
R22200, £5%, 14 W Resistor110000-221
R33300, 45%, %& W Resistor110000-331
RA2200, +5%, 4 W Resistor110000-221
RS, RO1kQ, £5%, % W Resistor110000-102
R73300, +5%, % W Resistor110000-331
R8&8200, +5%, 14 W Resistor110000-821
RO3300, £5%, 4 W ResistorTannn.231
RIO2200, £5%, % W Resistor110000-221
Rn4708, £5%, Ye W Resistor110000-471
RI24.70, £5%, % W Resistor110000472
R13220, +5%, % W Resistor110000-221
RI43301, £5%, 4 W Resistor110000-331
RIS1 kf. £5%. 4 W Resistoranneine
RIG, R172200, £5%, 4 W Resistor110000-221
RIS.3300, +5%, % W Resistor110000-331
RID2200, +5%, 4 W Resistor110000.221
R201 kf, +5%, 4 W Resistor110000-102
R21-R2439k, +5%, 4 W Resistor110000-393
R25-R281KQ, +5%, % W Resistor110000-102
R29-R324700, +5%, 4 W Resistor110000-471
R33,100 kM, +5%, 4 W Resistor110000-101
R34-R37470.0, £5%, 4 W Resistor110000-471
R38-R451kQ, 45%, 4 W Resistornaen0-102
R4G-R49470.0, £5%, % W Resistor110000-471
R50-R571kM, +5%, 4 W Resistor110000-102
R58-R6O100 D. +5%. % W ResistorHoaeno.10
R6I-R68470 Q, +5%, “4 W Resistor110000-471
R69, R702202, +5%, 4 W Resistor110000-221
R71-R741kQ, 5%, 4 W ResistorNONND-102
RIS2208, +5%, % W Resistor120000-221
R76100 kQ, +5%, % W Resistor110000-104
R77-R79LKQ. 45%. % W ResistorMannan?
R802202, +5%, % W Resistor110000-221
RBI3302, +5%, 4 W Resistor110000-331
R82, R83.Of Resistor110005-001
RNI, RN210 kQ, 10 Pin, SIP Resistor118002-103

Sockets

IN, IP24-Pin Medium Insertion-Force Socket79-4224
2A, 2D24-Pin Medium Inscation-Porce Socket79-4224
3A, 3B24-Pin Medium Insertion-Force Socket79-42C24
2N, 2P24-Pin Medium insertion-Force Socket79-42C24

(continued on next page)

4:25

Page 50

Tlupurateu Farts Lasts 1, ROBOT

I, ROBOT CPU PCB Asscmbly Parts List, continued

DesignatorDescriptionPart No.
1A, 1B28-Pin Medium Insertion-Force Socket79-42C28
1c28.Pin Mediinm Insertian-Rorce Socket79-4228
IDE28-Pin Medium Insertion-Force Socket79-4228
IEE28-Pin Medium Insertion-Force Socket79-42C28
H/F28-Pin Medium Insertion-Force Socket70-42028
1H28-Pin Medium Insertion-Force Socket79-42C28
yk28-Pin Medium Insertion-Force Socket79-42C28
IK/L28-Pin Medium Insertion-Force Socket79-42C28
ILM28-Pin Medium Insertion-Force Socket79-42628
4c28-Pin Medium Insertion-Force Socket79-42C28
3E, 4E40-Pin Medium Insertion-Force Socket79-42C40
415K40.Pin Medium Insertion-Force Socket79-42C40
4151.40-Pin Medium Insertion-Force Socket79-42C40
415M40-Pin Medium Insertion-Force Socket79-42C40
4I5N40.Pin Medium Insertion-Force Socket9.42040

Transistors

QI, Q2‘Type-2N3904 Transistor34-2N3904
3, 04Type-2N6044 ‘Transistor34-2NGU44
Qs‘Type-2N3904 Transistor34-2N3904

Miscellaneous

3)8-Station, Dual-Inline Package (DIP) Switch160031-008
SE8-Station, Dual-Inline Package (DIP) Switch160031-008
Yl12,069 MHz Crystal144000-001

Test Point (Acceptable substitute is part no. 020670-01) 179051-002 Nylon Snap-In Fastener 81-4302

4-26

Page 51

Tilusteated Parts Lists i sy hacer

4-28 ae

it Ks qe a3 C ig is i

cc Co, — |III]| ce ” a2 fag 8

. aiatea —— i nt iil

co

Figure 4-10 I, ROBOT Video PCB Assembly A042683-21 A

Page 52

1, ROBOT illustrated Parts Lists

Figure 4-10 1, ROBOT Video PCB Assembly, continued. A042683-21 A

4.29

Page 53

Tlhnseteared Dare Tiste 1 Rarer

I. ROBOT Video PCB Assembly Parts List

DesigaatorDescriptionPart No.

Capacitors

a0.1 wR, 50 V, Ceramic Capacitor122002-004
c2-C4100 pF, 23 ¥, Elecuvlytic Capaciwor24230107
C5-C380.1 wR, 50 V, Ceramic Capacitor122002-004
C40, C410.1 uF, 50 V, Ceramic Capacitor122002-004
C43-C970.1 wF, 50 V, Ceramic Capacitor122002-004

Diode

CRIType-MV5053 Light Emitting Diode+38MV5053

Integrated Circuits

1A‘Type-7418245 Integrated Circuit37-74LS245
1B‘Type-74LS244 Integrated Circuit37-TALS244
1bType 7ALS245 Integeated Circuit37 PALS245
IF‘Type-74L8244 Integrated Circuit37-741S244
1H‘Type-74L58244 Integrated Circuit37-74LS244
yarType 7ALS157 Integrated Ciecuit37 7ALSIST
IR‘Type-74LS163A Integrated Circuit37-74LSIG3A
2A‘Type-74LS245 Integrated Circuit37-7ALS245
2BType 74LS2 44 Integeated Circuit37 7ALS244
2E‘Type-74LS245 Integrated Circuit37-7ALS245
ar‘Type-7418244 Integrated Circuit37-74LS244
2H‘Type-7418374 Integrated Circuit37-74LS374
2J-2L‘Type-7418157 Integrated Circuit37-7418157
2M, 2N‘Type-2114-2 Integrated Circuit90-7036
2RType-74LS195 Integrated Circuit37-7ALSIO5
3A‘Type: 74532 Integrated Circuit3774832
3BType-74L508 Integrated Circuit37-741508
3cType-741S163A Integrated Circuit37ETALSIG3A
3D‘Type-7415157 Integrated Circuit37-7ALS1S?
3E, 3EType-74LSI63A Integrated Circuit37-TALSIO3A
3H‘Type-74LS257 Integrated Circuit377418257
3), 3KTypc-74L5163A Integrated Circuit37-7ALSIOZA
3L‘Type-74L5257 Integrated Circuit377418257
3M-3PType-74LS1634 Integrated Circuit37-74LSIG3A
oRTyp 415244 Ine grad Circuita7 741s244
4a-4D‘Type-74L5374 Integrated Circuit37-7ALS374
4EType-745133 Integrated Circuit137335-001
4E‘Type-74L8374 Integrated Circuit37-TALS374
4H0KCustom Integrated Circuit137410-101
4P‘Type-741827 Integrated Circuit37-74LS27
4RType-748374 Integrated Circuit37-7483 74
3DType-741892 Integrated Circuit37741832
SEType-74125 Integrated Circuit37-74125
5K, 5LType-74S157 Integrated Circuit37-748157
3MType -74L5279 Integrated CircuitBP TALG2TS
SNType-741S74 Integrated Circuit37-7ALSTA

(cantinned on neve page)

Page 54

1, RARE,

I. ROBOT Video PCB Assembly Htuseeated Parts Lint

Parts List, continued

NesignatorDescriptionPart No.
SP‘Type-74508 Integrated Circuit3774808
5R‘Type-74S04 Integrated Circuit37-74804
6AType-74LS125Integrated Circuit137317-001
6B‘Type-741874 Integrated Circuit37-TALSTA
6CType-74L$257 Integrated Circuit377418257
GEType-74L504 Integrated Circuit37-741804
oF‘Type-74125 Integrated Circuit3774125
GL, OM‘Type-7407 Integrated Circuit37-7407
GNType-74808 Integrated Circuit37-74S08
op‘Type-741874 Integrated Circuit37-74LS74
ORType-74832 Integrated Circuit37-74832
7A, 7BType-74LS32 Integrated Circuit3TTAIS32,
vA)Type-74S174 Integrated Circuit137209-001
7K‘Type-74L532 Integrated Circuit37-7ALS32
7LType-74S08 Integrated Circuit37-74808
™‘Type-741574 Integrated Circuit37-74LS74
7N‘Type-741S11 Integrated Circuit137149-001
7PType-74532 Integrated Circuit47-74832
TR‘Type-74S00 Integrated Circuit37-74800
8B-8FType-741S163A Integrated Citcuit37-7ALS163A,
8H‘Type-741574 Integrated Circuit37-7ALS74
8)‘Type-74804 Integrated Circuit37-74804
8K‘Type-74510 Integrated Circuit137236-001
BL‘Type-741S74 Integrated Circuit37-74LS74
8M‘Type-74L804 Integrated Circuit37-741804
8NType-74LS00 Integrated Circuit37-74L800
8P‘Type-74LS74 Integrated Circuit37-74LS74
8R‘Type-74508 Integrated Circuit37-74808
9A, 9B‘Type-7418374 Integrated Circuit37-74L8374
9C, 9D‘Type- 741885 Integrated Circuit37-74LS85
OE, OF‘Type-74885 Integrated CircuitALT4S8S
oH‘Type-74LS86 Integrated Circuit37 74LS86
OFType-74S08 Integrated Circuit3774808
OK‘Type-74L521 Integrated Circuit137210-001
OL‘Type-74S04 Integrated Circuit37AASO4
OM‘Type-74574 Integrated Circuit37-748 74
ON‘Type-74800 Integrated Circuit37-74800
9p‘Type-74S04 Integrated Circuit3774804
10A‘Type-745157 Integrated Circuit37-748157
10B‘Type-74LS157 Integrated Circuit37-7418157
10D‘Type-74LSI63A Integrated Circuit37-741S163A
10EType-74S163 Integrated Circuit137274001
10H, 10J‘Type-741574 Integrated Circuit37-74S74
10K‘Tyne-745160 Integrated CircuitARAN

(continued on next page)

Page 55

Ulustrated Parts Lists i, ROBOT

I, ROBOT Video PCB Assembly Parts List, continued

DesignatorDescriptionPart No.
10L‘Type-74S163 Integrated Circuit137274001
10M-10RType-748112 Integrated Circuit1373.34.01
10BType-74800 Integrated Circuit37-74500
1A‘Type-7415157 Integrated Circuit37-74L8157
RF‘Type-74183 Integrated Circuit37-7413,
MFType-4164-15 Integrated Circuit137339-150
11H‘Type-4164-15 Integrated Circuit137339-150
1-11NType-4164-15 Integrated Circuit137339-150
1p‘Type-74S10 Integrated Circuit137236-001
UR‘Type-74808 Integrated Circuit37-74S08
12B-12E‘Type-74153 Integrated Circuit3774153
VR‘Type-d164.15 Integrated Circuit137339150
12H-12N‘Type-4164-15 Integrated Circuit137339-150
12P‘Type-74S00 Integrated Circuit37-74800
VR‘Type-741 SIST Integrated Circuit37-TALSIST
BA‘Type-74LS163A Integrated Circuit37-7ALSIGZA
13B, 13Type-74189 Integrated Circuit37-74189
Bn‘Type-741S378 Integrated Circuit137305-001
BEType-74LS240 Integrated Circuit137251-001
1BF‘Type-74L374 Integrated Circuit37-7ALS374
13H, 13)Type-74LS158 Integrated Circuit37-7ALSIS8
13K, 13L‘Type-7415174 Integrated Circuit37-74LS174

Read-Only and Random-Access Memories

1G, 1D‘Type-Gu6-2 RAM Integrated Circuit15 TZI-OOL
2C, 2DType-Gll6-2 RAM Integrated Circuit137211-001
2P‘Type-82S185 ROM Integrated Circuit136029-124
4LType-82S09 RAM Integrated Circuit137322-001
4M.‘Type-825123 ROM Integrated Circuit136029-125,
riesType-82$123 ROM Integrated Circuit136029-132
7DType-825123 ROM Integrated Circuit136029133
7HType-B25151 ROM Integrated Circuit156029-126
10CType-82S129 ROM Integrated Circuit136029-131

Sockets

1¢,1D24-Contact, Medium-Insertion-Force Socket79-42C24
2C,2D24-Contact, Medium-Insertion-Force Socket79-42C24
4L28-Contact, Medium-Insertion-Force Socket7379-42028
4HAK24-Conuact. Medium-Insertion-Force Socket(uses two 24-pin sockets)79-4224

Transistors

Q1-04‘Type-2N3904 Transistor34-2N3904
cordType-2N3904 Transistor34-2N3904

(continued on next page)

4-32

Page 56

[ROBOT Illustrated Parts Lisi

I, ROBOT Video PCB Assembly Parts List, continued

DesiguawrDesuripuunFart Nu.

Resistors

Rt6608, +3%, 4 W Resiswr110000-G81
R2,33302, £5%, 4 W Resistor110000-331
Re270, 45%, %& W Resistor110000-270
RS220, +5%, 4 W Resistor110000-220
RO-RB270, +5%, % W Resistor110000-270
RO228, £5%, & W Resistor110000-220
RIO, RU270, 45%, % W Resistor110000-270
RIZ, Rl}2200, +5, tA W Resistor110000-221
RI4-R221kQ, +5%, & W Resistor110000-102
R25TkQ, £5%, 14 W Resistor0000-102
RL0Z2hO, £376, a W Rosin0000-222
R271000, +5%, 4 W Resistor110000-101
R282200, +5%, 4 W Resistor110000-221
ROLkG, £5%, & W Resistor110000.102
R322.2kQ, £5%, % W Resistor0000-222
R331000, 5%, 4 W Resistor110000-101
R34220.0, £5%, % W Resistorm10000-221
R371 kM, 5%, M4 W Resistor110000-102
R382.260, 45%, % W Resistor110000-222
R39.100.2, +5%, 4 W Resistor110000-101
R402200, +5%, % W Resistor110000221
RA5602, £5%, % W Resistor110000-561
R42-R444309, +5%, % W Resistor110000-431
R452.2100, 159, 4 Resiotor110000 222
RAG4.7 kG, +5%, 4 W Resistor110000-472
RA?9.1 kD, £5%, % W Resistor110000-001
RID22kO, 15%, % W Resistor110000-223
RSO1kQ, +5%, 4 W Resistor110000-102
R512202, 45%, 4 W Resistor110000-221
R52-R581kf, £5%, % W Resistor110000-102
R6O-R624700, +5%, 4 W Resistor110000-471
R631kQ, £5%, % W Resistor110000-102
RGA, RES2200, 159%, 4 W RecistorTION.F 91
ROG3300, +5%, % W Resistor110000-331
R67-R69332, +5%, 4 W Resistor110000-330
RIO1kR, 5%, % W Resistor110000-102
RTL470, 45%, % W Resistor110060-470
siPt220 Q, 8-Pin SIP Resistor118007-221

Miccellaneane

LI-L31 gH Inductor141007-001
YI20 MHz Crystal144000-003
Page 57

Illustrated Parts Lists

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reprecucion foraiden without the spect wnt ten permission o Alar, ne, Sunnyvale, CA. This drawing is only is thereat con ‘nor any ight to reproduce this drawing or any part therect. Except for manutacture ty vendors of lati Inc. and for manufacture under the corporations witlen license, no ight is grarted 10 reproduce this. ‘drawing orthe subject attertnereot, unless by wnten agreement with or written permiaaion from the wor por + €50,/000pF 4+ ¢51,1000pF

Gbes4 Gocss

Figure 4-11 EMI Shield PCB Assembly A037667-02 B

  • ROROT,
Page 58

1, POROT

EMI Shield PCB Assembly Illustrated Parts Lists

Parts List

DesignatorDescriptionPart No.

Capacitors

Cl, C2Q.L BE, +80%, -20%, 50 V Ceramic-Disk Capacitor122002104
3G.1 pk, +80%, -20%, 50 V Ceramic-Disk Capacitor122002-104
C6-C150.01 fF, +80%, -20%, 25 V Ceramic-Disk Axial-Lead Capacitor122005-103
cl70.01 gE, + 80%, -20%, 25 V Ceramic-Disk Axial-Lead Capacitor122005-103
C21Ul AE, +80%, -20%, 50 V Ceramic-Disk Capacitor122002-104
€25-C290.01 pF, +80%, -20%, 25 V Ceramic-Disk Axial-Lead Capacitor122005-103
C35, C36,0.01 wE, +80%, -20%, 25 V Ceramic-Disk Axial-Lead Capacitor122005-103
C370.1 pF, +80%, -20%, 50 V Ceramic-Disk Capacitor19200-1046
C40O.t RE, +80%, -20%, 50 V Ceramic-Disk Capacitor122002-104
C43,O.1 KE, +80%, -20%, 50 V Ceramic-Disk Capacitor122002-104
C44470 pF, 100 V, NPO Ceramic-Disk Axial-Lead Capacitor(Acceptable substitute is122016-471

part no. 122013-471)

c45,1000 pF, +5%, 100 V, NPO Ceramic-Disk Axial-Lead Capacitor122016-102
046, C47470 pE, 100 V, NPO Ceramic-Disk Axial-lead Capacitor(Acceptable substitute is122016-471

part no. 122015-471)

o540.1 BE, +80%, -20%, 50 V Ceramic-Disk Capacitor122002-104
57O.1 zF, +80%, -20%, 50 V Ceramic-Disk Capacitor122002-104

Connectors

Ply30-Pin Card-Bdge Connector(Acceptable substitute is part no. 179046030)179073-030
P2044-Pin Card-Edge Connector(Acceptable substitute is Part no, 179046-044)179073-044

Miscellaneous Spacer 037873-01 #4-40 x 4 Cross-Recessed Pan-Head Screw 72-1404F

Page 59

YOUR COMMENTS, PLEASF!

Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.

if you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name

Firm D Disteibutor

Address 1 Operator City Country 0 Other

Phone: Country Code Local Number TM 251 1st printing

Page 60

Attach Necessary Postage

Atari Ireland Limited Attn: Field Service/Coin-Op Division Tipperary Town. Ireland

swosg

28po spp adey

Page 61

" e

ig

» a EES EE EE

Warranty

Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service fora period of ninety (90) days from date of shipment. Seller warrants that its video displays and laser-video disc players (in games supplied with displays and video-disc players) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment, None of the Seller’s other products or parts thereof are wartanted. If the products described in this manual fail to conform to this warranty, Seller's sole liability shail be, at ite option, to repair, replace, or credit Buyer's account for euch products which are retmened to Seller during said warranty period, provided:

  • Seller is promptly notified in writing upon discovery by Buyer that said products are defective:
  • Such products are returned prepaid to Seller's plant; and
  • Seller’s examination of said products discloses to Seller's satisfaction that such alleged defects existed and were nat canced hy acridenr, misnse, neglect, alteration, improper repair, installation, or improper testing. Inno event shall Seller be jiable for loss of profits, loss of use, incidental or consequential damages. Except for any express warranty set forth in a written contract betweon Sellor and Buyer which contract supersedes the terms herein, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all otber obligations or liabilities on the Seller's part, and it neitber assumes nar authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products by Seller.

The use of any non-Atari parts may void your warranty, according to the terms of the warranty, The use of any non-Atari parts may also adversely affect the safety of your game and Cause injury to you and others. Be very cautious in using non-Atari-supplied components with our games, in order to ensure your safety. Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is pertormed by such distributor. < © s ; ; ; :

Page 62

ATARI. INC. 790 SYCAMORE DRIVE PO. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 © TELEX 35-7488