CATHODE RAY TOMES

Jambo Safari STD 4th Printing

Jambo! Safari (Rev A) (Sega, 1999) · Manual · 85 pages · 116 sections · original scan

Page 1

STD VERSION 2002 PRODUCTION

OWNER’S MANUAL

SEGA ENTERPRISES, INC. USA

MANUAL NO. 999-0886-01

Page 2

VISIT OUR WEBSITE!

Oe" 9 SegaService.com 2 @i+¢ = | Sherlock Preferences | Larger Smaller = Deal (3) http://www seuserviee.com/

Dart's Office Game Manuals Seerenh Whet's New

EHEIGR] pcopte have visited ths page since 3/16/01

ene If you have any questions or comments

Pree ys about this site please E-Mail to Darl Davidson@seu sega com

tax 415.701.0604 i i

i i

THUR WER BUTE POWERED BY

WebSTAR 4-3

You will need the ot items to view this =a in its entirety

AllPlatforms Windows Macintosh

Page 3

BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain the safety:

To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary.

Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. are used. Be sure to understand the contents of the displays before reading the text.

Indicates that mishandling the Indicates that mishandling the product product by disregarding this by disregarding this caution will cause

warning will cause a potentially a slight hazardous situation which can
WARNING! hazardous situation which can CAUTION! result in personal injury and or material result in death or serious injury. damage.

For the sage usage of the product, the following pictographs are used:

Indicates “HANDLE WITH CARE.” In order to protect the human body an equipment, this display is attached to places where the Owner’s Manual and or Service Manual should be referred to.

© Perform work in accordance with the instructions herein stated. Instructions for work are explained by paying attention to the aspect of accident prevention. Failing to perform work as per the instructions can cause accidents. In the case where only those who have technical expertise should perform the work to avoid hazardous situation, the instructions herein state that the serviceman should perform such work.

© Be sure to turn off power before working on the machine. To prevent electric shock, be sure to turn off power before starting the work in which the worker touches the interior of the product. If the work is to be performed in the power-on status, the Instruction Manual herein always states to that effect.

© Be sure to ground the Earth Terminal (this, however, is not required in the case where a power cord with earth is used). This product is equipped with the Earth Terminal. When installing the product, Connect the Earth Terminal to the “accurately grounded indoor earth terminal” by using an earth wire. Unless the product is grounded appropriately, the user can be subject to electric shock. After performing repair, etc. for the Control equipment, ensure that the Earth Wire is firmly connected to the Control equipment.

© Ensure that the Power Supply used is equipped with an Earth Leakage Breaker. This product does not incorporate the Earth Leakage Breaker. Using a power supply which is not equipped with the Earth Leakage Breaker can cause a fire when earth leakage occurs.

© Be sure to use fuses which meet the specified rating. (only for the machines which use fuses). Using fuses exceeding the specified rating can cause a fire and electric shock.

Page 4

O Specification changes (removal of equipment, conversion and addition) not designated by SEGA are not allowed. The parts of the product include warning labels for safety, covers for personal protection, etc. It is very hazardous to operate the product by removing parts and or modifying the circuits. Should doors, lids and protective parts be damaged or lost, refrain from operating the product, and contact where the product was purchased from or the office herein stated. SEGA shall not be held responsible for any accidents, compensation for damage to a third party, resulting from the specifications not designated by SEGA. ©. Ensure that the product meets the requirements of appropriate Electrical Specifications. Before installing the product, check for Electrical Specifications. SEGA products have a nameplate on which Electrical Specifications are described. Ensure that the product is compatible with the power supply voltage and frequency requirements of the location. Using any Electrical Specifications different from the designated Specifications can cause a fire and electric shock. © _ Install and operate the product in places where appropriate lighting is available, allowing warning labels to be clearly read. To ensure safety for the customers, labels and printed instructions describing potentially hazardous situation are applied to places where accidents can be caused. Ensure that where the product is operated has sufficient lighting allowing the warnings to be read. If any label is peeled off, apply it again immediately. Please place an order with where the product was purchased from or the office herein stated. © When handling the Monitor, be very careful. (Applies only to the product w/monitor.) Some of the monitor (TV) parts are subject to high tension voltage. Even after running off power, some portions are still subject to high tension voltage sometimes. Monitor repair and replacement should be performed only be those technical personnel who have knowledge of electricity and technical expertise. © Besure to adjust the monitor (projector) properly. (Applies only to the product w/monitor.) Do not operate the product leaving on-screen flickering or blurring as it is. Using the product with the monitor not properly adjusted may cause dizziness or a headache to an operator, a player, or the customers. © _ When transporting or reselling this product, be sure to attach this manual to the product. In the case where commercially available monitors and printers are used in this product, only the contents relating to this product are explained herein. Some commercially available equipment has functions and reactions not stated in this manual. Read this manual together with the specific Instruction Manual of such equipment.

° Descriptions herein contained may be subject to improvement changes without notice. ¢ The contents described herein are fully prepared with due care. However, should any question arise or errors be found, please contact SEGA.

INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION.

Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation. Before turning on power, check the following points to ensure that the product has been transported in a satisfactory status. Are there any dented portions or defects (cuts, etc.) on the external surfaces of the cabinet? Are Casters and Adjusters, damaged? Do the power supply voltage and frequency requirements meet with those of the location? Are all wiring connectors correctly and securely connected? Unless connected in the correct direction, connector connections can not be made accurately. Do not insert connectors forcibly. Do power cords have cuts and dents? Do the fuses used meet specified rating? Is the Circuit Protector in an energized status? Are all accessories available? Can all Doors and Lids be opened with the Accessory keys? Can Doors and Lids be firmly closed?

Page 5

TABLE OF CONTENTS

INTRODUCTION OF THE OWNERS MANUAL GENERAL PRECAUTIONG........ccceceeeeeeeees

  • PRECAUTIONS TO BE HEEDED FOR OPERATIO 4.5
  • NAME OF PARTS 6
  • ACCESSORIES. 1-8
  • ASSEMBLING Al 9~15
  • PRECAUTIONS TO BE HEEDED WHEN MOVING MACHIN 16
  • CONTENTS 17~19
  • EXPLANAT! 20~30 Tl

7-4

1-6 Td

  • HAND

8-2

  • SHIFT L

9-2

  • ACCEL & B 7 36-37 0-1 ADJUSTING AND REPLACING THE VR. 36-37 0 T BRAKE AND ACCEL 37
  • CO 38-41
  • MO 42~44
  • REP CENT LAM 45 3-1 REPLACEMENT OF FLUORESCENT LAM 45
  • PER
  • TRO
  • GAMEB - 6-1 REMOV 48 6-2. REPLACMENT OF FUSE............ 49 6-3 COMPO E GAME BOARD. 50
  • DESIGN RELATED PARTS. 51
  • PARTS LIST.
  • WIRE COLO
  • WIRING DIAGRAMS
Page 6

SPECIFICATIONS

Installation space: 68 in(L) x 41 in.(W)

Height: 84 in.

Weight: Approx. 550 Ibs.

Power maximum current: 3.5 Amp AC 120V 60 Hz

MONITOR: 29” SANWA MONITOR

INTRODUCTION OF THE OWNERS MANUAL

SEGA ENTERPRISES, LTD., has for more than 30 years been supplying various innovative and popular amusement products to the world market. This Owners Manual is intended to provide detailed descriptions together with all the necessary installation, game settings and parts ordering information related to CRAZY TAXI, a new SEGA product.

This manual is intended for those who have knowledge of electricity and technical expertise, especially in ICs, CRTs, microprocessors, and circuit boards. Read this manual carefully to acquire sufficient knowledge before working on the machine. Should there be a malfunction, non-technical personnel should under no circumstances touch the interior system. Should the need arise, contact our main office, or the closest branch office listed below.

SEGA ENTERPRISES, INC. USA -Service Department Customer Service 45133 Industrial Drive Fremont, CA 94538 Phone 415-701-6580 Fax 415-701-6594 7:30 am - 4:00 pm, Pacific Standard Time Monday thru Friday

Page 7

General Precautions

Follow Instructions: All operating and use instructions should be followed.

Attachments: Do not use attachments not recommended by the product manufacturer as they may cause hazards. Accessories: Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use only mounting accessories recommended by the manufac

turer.

Moving the Product: This product should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product to overturn. Ventilation: Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating; these openings must not be blocked or covered. The openings should never be blocked by placing the product in a built-in installation such as a bookcase or rack unless proper ventilation is pro vided or the manufacturer’s instructions have been adhered to.

Power Sources: This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your local power company. For products intended to operate from battery power or other sources, refer to the operating instructions. Grounding or Polarization: This product is equipped with a three-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. Power Cord Protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. Overloading: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

Object and Liquid Entry: Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. Servicing: Do not attempt to service this product yourself as opening or removing covers may expose you to danger ous voltage or other hazards. Refer all servicing to qualified service personnel. Damage Requii ‘ing Service: Unplug this product from the wall outlet and refer servicing to qualified service person nel under the following conditions:

  • If the power cord or plug is damaged;
  • If liquid has been spilled, or objects have fallen into the product;
  • If the product has been exposed to rain or water;
  • If the product does not operate normally when following the operating instructions. Adjust only those controls that are explained in the operating instructions. An improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation;
  • If the product has been dropped or damaged in any way;
  • When the product exhibits a distinct change in performance; this indicates a need for service. Replacement Parts: When replacement parts are required, be sure the service technician has used replacements parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Page 8

Safety Check: Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. Heat: The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Lithium Battery- Dispose of batteries only in accordance with the battery manufacturer’s recommenda tions. Do not dispose in an open flame condition, since the battery may explode. Cleaning: When cleaning the monitor glass, use water or glass cleaner and a soft cloth. Do not apply chemicals such as benzine, thinner, etc. Location: This an indoor game machine, DO NOT install it outside. To ensure proper usage, avoid install ing indoors in the places mentioned below: + Places subject to rain/water leakage, or condensation due to humidity; + In close proximity to a potential wet area; + Locations receiving direct sunlight; + Places close to heating units or hot air; +In the vicinity of highly inflammable/volatile chemicals or hazardous matter;

  • On sloped surfaces; + In the vicinity of emergency response facilities such as fire exits and fire extinguishers;

+ Places subject to any type of violent impact;

+ Dusty places.

INSTALLATION PRECAUTIONS + Verify the amperage of the branch circuit outlet before plugging in the power plug. Do not overload the circuit. + Avoid using an extension cord. If one is required, use an extension cord of type SJT, 16/ 3 AWG rated min. 120 VAC, 7A.

  • Moving this unit requires a minimum clearance (of doors, etc.) of 32” (W) by 77” (H). + For the operation of this machine, secure a minimum area of 32” (W) by 42”(D).

REGULATORY APPROVALS This game has been tested and found to comply with the Federal Communications Commission Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • This device may not cause harmful interference, and
  • this device must accept any interference received, including interference that may cause undesired operation. This game has been tested and listed by Underwriters Laboratories, Inc., to ANSI/UL22.

LISTED

SK92

AMUSEMENT MACHINE

Page 9
  • PRECAUTIONS TO BE HEEDED FOR OPERATION

In order to prevent accidents, be sure to comply with the following points before and during operation.

PRECAUTIONS TO BE HEEDED FOR OPERATION BEFORE STARTING THE OPERATIO.

@ In order to avoid accidents, check the following before starting the operation: Check if all of the adjusters are in contact with the surface. If they are not, the cabinet can

WARNING! move and cause an accident.

Ensure coatact with Floor

Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step. To avoid electric shock, check to see if door & cover parts are closed.

@ To avoid electric shock, short circuit and or parts damage, do not put the following items on or in the periphery of the product:

Flower vases, flower pots, cups, water tanks, cosmetics, and receptacles/containers/vessels containing chemicals and water.

To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can 7 cause the player to come into contact with or hit others and result in injury or

CAUTION! trouble.
Page 10

PRECAUTIONS TO BE HEEDED DURING OPERATION

To avoid injury and accidents, those who fall under the following catagories are not allowed to play the game:

CAUTION! * Intoxicated persons
  • Those who have high blood pressure or heart problems.
  • Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc.
  • Persons susceptible to motion sickness.
  • Persons whose acts runs counter to the products warning displays.
  • Instruct those who wear high-heeled shoes to refrain from playing the game by explain. ing that playing the game with high-heeled shoes is very dangerous and likely to cause a potentially hazardous situation.

To avoid electric shock and short circuit, do not allow customers to put hands and fingers or extraneous matter in openings of the product or small openings in or around doors.

CAUTION! To avoid electric shock and short circuit, do not allow the customers to unplug the

power plug without a justifiable reason. Although this product has the accident preventive covering attached to potentially hazardous places where hand and fingers could be caught, small children are unable to perceive hazards. Use care so that small children do not come close to the product when in play. Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage and/or falling down, resulting in injury due to fragments and falling down.

Page 11
  • NAME OF PARTS

MARQUEE

MONITOR

CONTROL PANEL

COIN TOWER

COCKPIT

GAME SPECIFICATIONS WIDTH in. LENGTH in. HEIGHT in. WEIGHT Ibs.

All measurements are and rounded UP

DURING SHIPPING 4s” x 70” xX 84” ~ 600 LBS.

WHEN ASSEMBLED 39” Xx 65” X 80” 550 LBS.

Page 12
  • ACCESSORIES

KEY MASTER KEY 220-5576 (2) (2) For the CASHBOX DOOR DESCRIPTION OWNERS MANUAL Part No. (Qty.) 4201-6468-03

Note

Figures — ane

If Part No. has no description, the Number has not been { 4 ‘0 asec) registered or can not be registered. Such a part may not | r be obtainable even if the customer desires to purchase it. — Therefore, ensure that the part is in safekeeping with you.

TAMPERPROOF WRENCH M8 540-0009-01 (1) =

Page 13

THE SHIPMENT METHOD DESCRIBED BELOW ONLY APPLIES TO ‘MODEL 3’ BOARDS CONTAINED IN THE

WARNING! FOLLOWING GAMES:

LOST WORLD, VIRTUA FIGHTER 3, SUPER GT, SEGA BASS FISHING, STRIKER 2 HARLEY DAVIDSON, RALLY 2, DAYTONA 2, DIRT DEVILS, HOUSE OF THE DEAD 2, OCEAN HUNTER, STAR WARS TRILOGY, ZOMBIE REVENGE, CRAZY TAXI

!!NEVER SHIP MODEL 3 / NAOMI GAME

BOARDS OUTSIDE OF CAGE!!

CARTON BOX 601-8928 (1) Used for transporting the GAME BOARD. {SUPPLIED WITH YOUR GAME}

DO NOT SHIP GAME BOARD WITHOUT THIS BOX AS IT MAY DAMAGE THE GAME BOARD AND VOID YOUR WARRANTY.

“CHECK SIDE” Display

FILTER BOARD

NO OTHER GAMES BOARDS ARE TO BE SHIPPED IN THE CAGE AS THEY MAY BE DAMAGED BEYOND REPAIR. PLEASE SHIP THEM WITHOUT CAGE PROPERLY PROTECTED DURING SHIPPING.

WARNING!
Page 14
  • ASSEMBLING AND INSTALLATION

Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling may cause damage to the machine, or malfunctioning to occur.

CAUTION! When assembling, be sure to perform work by plural persons. Depending on the assembly work, there are some cases in which performing the work by a single person can cause personal injury or parts damage.

When carrying out the assembly work, follow the procedure in the following 5-item sequence:

ASSY OF THE REAR CABI (COCKPIT)

ASSY OF BILLBOARD

SECURING IN PLACE (ADJUSTER ADJUSTMENT)

POWER SUPPLY TREES ASSEMBLING CHECK

Note that the tools such as a phillips screwdriver and wrench for M16 hexagon bolt w/24 mm width across flats are required for the assembly work.

ASSY OF REAR CABI (COCKPIT)

Permanantly tightening the hex bolts should not be

CAUTION! completed until the leg levelers are adjusted properly.
Page 15

@ Install the coin chute tower on the Right-hand side of cabinet. Open the coin chute door and the cashbox door to secure with the 4 hexagon bolts from inside the doors. Please note that the Coin Chute tower is NOT mounted on the Left-hand side as shown above.

COIN CHUTE DOOR

COIN CHUTE TOWER

HEXAGON BOLT (4)

MBX 20 FLAT WASHER

NOTE: ON SEGA’ CRAZY TAXI GAME THERE IS NOT TWO COCKPITS SIDE BY SIDE AS PICTURED ABOVE. THE GAME HAS ONLY ONE COCKPIT AND THE COIN TOWER WILL MOUNT ON THE RIGHT SIDE AS YOU FACE THE CABINET..
Page 16

2 ASSY OF THE BILLBOARD

Due to its large size, it is very difficult for one person alone to install the billboard, Make sure 2 or more persons are available to perform this work. Attempting to perform the installation alone can cause an accident.

WARNING!
  • Mount Billboard on cabinet by ensuring the front lip of the Billboard is securely placed under the mounting bracket already installed on the cabinet. Fasten with the 3 hexagon bolts.
  • Connect all of the 4 connectors inside the Billboard box (This needs to be done prior to final installation of Billboard Assy).

—. HEXAGON BOLT (4a) (black)

BILLBOARD HOLDER

HEXAGON BOLT (4) (black) wana TRUSS SCREW (3)

BILLBOARD CASE

BILLBOARDS CONNECTOR

Page 17

3 SECURING IN PLACE (ADJUSTER ADJUSTMENT)

Be sure to have all the Adjusters make contact with the surface. Unless the Adjusters come into contact with the surface, the Cabinet can move of itself, causing an acci-

WARNING! |} 4°"

This machine has 4 each of casters and adjusters (shown below). When the installation position is determined, cause the adjusters to come into contact with the floor directly, make adjustments in a manner so that the casters will be raised approximately 5mm. from the floor and make sure that the machine position is level.

@ Move the machine to the installation

position.

@) Cause all of the leg levelers to make

contact with the floor. By using a wrench,

make adjustments in the height of the leg

adjusters to ensure that the machine's position is level.

QR) After making adjustments, fasten the leg

adjuster nut upward and secure the height of the leg adjuster. \ Leg Leveler

Leg Leveler

Page 18

4 | power supply

@ Ensure that the power cord is not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord can cause an electric shock or short circuit. @ Ensure that the wiring position is not in the customer's passage way or the wiring has

WARNING! protective covering.

Connect the game to the power supply and turn on power to the game. Before connecting power supply be sure that power switch is off

MAIN SW

@) Turning the AC unit’s main switch on will cause the machine

to start the power check and network check automatically.

Q) In the Power On check, the steering wheel turns left and right,

and then returns to the centering position and stops. In this check, the values of the VR inside the control panel are corrected.

6) Until this check is finished, and the steering wheel stops, do

not touch the steering wheel or play the game.

If you do, the steering reaction during the game (reaction at the time of course-out or crash) can not be obtained correctly. In the case of an abnormal reaction during the game, turn power on again from the beginning and complete the power on check.

To the Power Supply

Socket oudet

Page 19

ASSEMBLING CHECK

The TEST MENU allows for each part of the cabinet to be checked, the Monitor to be adjusted, and the coin and game related various functions to be performed.

Selecting the MEMORY TEST on the test mode menu screen causes the on-board memory to be tested automatically. The game board is satisfactory if the display beside each IC No. shows GOOD.

MENU MODE

SYSTEM MENU

RAM TEST JVS_ TEST SOUND TEST C.R.T. TEST SYSTEM ASSIGNMENTS, COIN ASSIGNMENTS: BOOKKEEPING BACKUP DATA CLEAR CLOCK SETTING

ROM BOARD TEST —> GAME TEST MODE (XxX KKK KKK KX]

EXIT SELECT WITH SERVICE BUTTON AND. PRESS TEST BUTTON VOLUME SETTING BOOKKEEPING BACKUP DATA CLEAR CRAZY TAX! TEST MENU

INPUT TEST OUTPUT TEST SOUND TEST GAME ASSIGNMENTS

-> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

SYSTEM TEST MODE MENU

INPUT TEST

ORIVE GEAR OFF REVERSE GEAR OFF START OFF COIN CHUTE #1 OFF COIN CHUTE #2 OFF SERVICE OFF TEST OFF HANDLE 80H ACCEL 30H BRAKE 30H

PRESS TEST AND SERVICE BUTTON TO EXIT

OUTPUT TEST

START LAMP ON

PRESS TEST BUTTON TO EXIT GAME TEST MODE MENU

Selecting the INPUT TEST on the Test Mode menu screen causes the screen (on Which each switch adnV.R. are tested) to be displayed. Press each switch. For the coin switch test, insert a coin from the coin

inlet with the coin chute door being open. If the display beside each switch indicates “ON”, the switch and wiring connections are satisfactory. Check the display of V.R. value for steering wheel and accelerator & brake. If the V.R. values are not satisfactory, make adjustments as neccesary.

In the OUTPUT TEST mode, carry out lamp test to ensure that each lamp lights up satisfactory.

Page 20

SOUND TEST

VOICE

EFFECT

BGM.

>EXIT

SELECT WITH SERVICE BUTTON AND. PRESS TEST BUTTON TO EXIT

CRLTEST 1/2

WHITE

PRESS TEST BUTTON TO CONTINUE In the TEST mode, selecting SOUND TEST causes the screen, on which sound related BD and wiring connections are tested, to be displayed. Be sure to check if the sound is satisfactorily emitted from each of speaker and the sound volume is appropriate.

In the TEST mode menu, selecting C.R.T. TEST allows the screen (on which the projector is tested) to be displayed. Although the projector adjustments have been made at the same time of shipment from the factory, color deviation, etc., may occur due to the effect caused by geomagnitism, the location building’s steel frames and other game machines in the periphery. By watching the

test mode screen, make judgement as to whether an adjustment is needed. If it is neccessary, adjust the

projector by refering to Section 9.

Perform the above inspections also at the time of monthly inspection.

Page 21
  • PRECAUTIONS TO BE HEEDED WHEN MOVING THE MACHINE

supply. Moving the machine with the plug as is inserted can damage the power cord and cause a fire or electric shock. @ When moving the machine on the floor, retract the Adjusters and ensure that Casters make contact with the floor. During transportation, pay careful attention so that Casters do not tread power cords. Damaging the power cords can cause an electric shock and/or short circuit. @ When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installa-

tion portions, due to the empty weight of the cabinet, and cause personal

injury.

‘A @ When moving the machine, be sure to pull out the plug from the power

WARNING!

Use care when handling glass made parts. When the glass is damaged, fragments of glass can cause injury

CAUTION!

DO NOT PUSH THE CABINET FROM THE

LEFT/RIGHT DIRECTION

Page 22
  • CONTENTS OF GAME

The following explanations apply to the case the product is functioning satisfactorily. Should there be any moves different from the following contents, some sort of faults may have occured. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation. During the Advertise mode, the Billboard’s Decoration Lamp lights up periodically. When the machine is energized, the Billboard’s Fluorescent Lamp is always lit. The Steering Wheel repeats centering action periodically. Automatic centering will apply to the Steering Wheel if it is not centered. During the Advertise Mode, sound is emitted from the Speaker beside the Monitor.

OUTLINE OF GAME

The Player as a taxi driver picks up a passanger (hereafter customer) randomly appearing on the the Game Field waiting for a taxi, and takes the Customer tot he desired destination. Time Limit is set for each Customer (displayed on the upper left-hand side of Customer while traveling). If the taxi takes Customer to the destination within the time limit, Customer pays the fare (the player earns points.). On the contrary, if the player fails to take the Customer to the destination within the time limit, Customer will get off and results in no fare (no points) for the player. The Player is to accomplish the above within the time limit of the game (displayed on the upper left-hand side of the screen) repetitively as many times as possible. When time limit becomes zero (0), the game is over. The game is aimed at earning money as much as possible by taking as many Customers as possible to their destinations within the time limit.

HOW TO OPERATE

The operation of Steering Wheel, and Accelerator & Brake pedals are similiar to an actual car. SHIFT LEVER Input to (D) towards the monitor side to drive forward, and to (R) towards you to reverse. Auto transmission and not manual is applied to speed shifting. The DR LAMP displays Forward (D) and Reverse (R), whichever is being inputted.

BRAKE PEDAL, ~\_ ACCELERATOR PEDAL

Page 23

HOW TO PLAY

® Insert a coin. Coin insertion causes credit(s) to be displayed on the screen. For example, in the case of 2 coins one credit setting, “INSERT COIN(S) CREDIT(S) 1/2” is displayed when one coin is inserted.

@ Inserting one play worth of coin(s) causes “PRESS START BUTTON” to be displayed and the START BUTTON to flash. Press the START BUTTON to have the character mode appear on this screen.

® In the Character Select Mode, select on-screen player character. Turn the Steering Wheel left or right to shift to each character select mode. Press the START button or step on either of Accel. or Brake pedal to decide on the character being displayed.

  • While the Character Select Mode is displayed, countdown is executed. Counting down to (0) causes the character being displayed to be selected automatically.

© When the character is determined, the game starts. The Taxi picks up the Customer who has the $ Mark above him/her. There is a circular mark signifying the Stop Area

in the periphery of Customer. Stop the taxi in the Stop ($) When the taxi comletely stops in the Stop Area, the on- ie yy

Area.

screen scene shifts and Customer rides in automatically. At Ni

this time, the taxi is in status not operable. When the Customer rides in, the neccessary time to the destination is added to the Game’s Time Limit. | The color of the $ mark represents the distance of the destination. Green indicates the furthest destination. The distance becomes shorter sequentially in order of green-- >yellowish green-->yellow-->-->orange-->red.

© Take the Customer to the destination. While traveling to the destination, time limit and the arrow showing the direction of destination are displayed on the screen. . . ARROW showing the direction ‘of Destination.

Game_Time Total Earnings (Total Score) (Playable Time) “~~ EP i fen | FARE to be paid by the present Customer 32 | when getting off. | Customer Time Scene_of Destination Displayed when the Customer rides i and the START button is pressed.

WeeRRE Name _of Destination Displayed together with the Scene of Destination.

Page 24

© The following explains as regards how to earn FARE (or score points). The minimum fare is earned at the time the taxi picks up the Customer. Basically, the best way to earn FARE is to take the Customer to their destiantion as fast as possible. In other words, since the time remaining when reaching the destination is converted into FARE, the more remaining time is, the greater the FARE the player earns. In addition to the above, receiving a tip is another way of increasing the FARE. The tip awarded for doing something to please the customer is added to the FARE. Details are as follows: @ Tip for dodging: Awarded when dodging other (ordinary) car at the very critical moment. @ Tip for Jumping: Awarded when the taxi jumps over trailers, etc. @ Tips for drifting: Awarded when the taxi drifts. When awarding tips, coins are sent in a flying motion from the Customer towards the FARE METER. If tips are consecutively earned, the earning rate increases (in combo) This combo effect resets if the taxi bumps against another ordinary car. The combo display appears below the FARE METER. The Customer’s fare is not added to the TOTAL FARE unless the Customer is taken to the destination.

@ When reaching the destination, drop off the Customer. Stop the taxi within the destination area mark. When the taxi completely stops within the area, the on-screen shifts to evaluation mode and the customer gets of automatically. the Customer’s evaluation displayed in characters depends on the remaining seconds of the Customer time when reaching the destination. @ SPEEDY: Display of more remaining time/money converted from time is paid. @ NORMAL: Display of normal remaining time/normal amount of money converted from time paid. @ SLOW: Display of less remaining time/less amount of money converted from time is paid. After suming up the above, the Customer’s FARE is determined and then the FARE is added to the TOTAL FARE. After TOTAL FARE calculations, the player ranking is displayed. The ranking is based on the score data of the 99 players played in the past. Customer's Evaluation

When the Taxi stops in the Destination Area.

The Customer gets off

® If the remaining time of the Customer becomes zero, the Customer becomes angry and gets off. At this time, the Customer’s FARE is not added to the TOTAL FARE.

® When the Game Time becomes 0, the game is over. The GAME OVER screen appears, with TOTAL EARNED, evaluation comment and RANKING displayed. If any credit(s) which is one play worth or more remains, the START LAMP unlit during game will then flash.

Page 25
  • EXPLANATION OF TEST AND DATA DISPLAY

By operating the switch unit, periodically perform the tests and data check. When installing the machine initially or collecting cash, or when the machine does not function correctly, perform checking in accordance with the explanations given in this section. The following shows tests and modes that should be utilized as applicable.

<

IMPORTANT! CAUTIONS TO BE HEEDED WHEN USING THE TEST MODE: In the case where plural machines are linked for communication play, if even one seat enters the test mode, all of the linked seats will enter the test mode. Therefore, if anyone of the linked machines is in play, use care so as not to use the test mode. The contents of the setting changes made will made will not be effective unless the test mode is finished in the test mode. When the setting is changed, be sureto “EXIT” in the menu mode. Do not press the TEST BUTTION during network check at the time of turning the power on or exiting from the test mode. If anyone of the linked machines uses the test mode during network check, all other Seats will continue network checking. Cause all of the Seats to reenter the test mode and then have all of the Seats exit from the test mode simultaneously.

TABLE 7 EXPLANATION OF TEST MODE

ITEMS DESCRIPTION SECTIONS

INSTALLATION | When the machine is installed, perform the following: 7-10, 7-11

OF MACHINE1. Check to see that each setting is as per standard setting1-6

made at the time of shipment. 7-7

  • In the INPUT TEST mode, check each SW and VR. 7-3.7-4
  • In the OUPUT TEST mode, check each of lamps. Tet
  • In the MEMORY TEST mode, check ICs on the IC Board.

Choose MEMORY TEST in the MENU mode to allow the

MEMORYMEMORY test to be performed. In this test, PROGRAM7-3, 7-4

RAM’s, ROM’s, and ICs on the IC Board are checked.

Periodically perform the following: 7-10, 7-11

PERIODIC 1. MEMORY TEST

SERVICING2. Ascertain each setting.1-6
  • In the INPUT TEST mode, test the CONTROL device
  • In the OUTPUT TEST mode, check each of lamps. 727

CONTROL 1.In the INPUT TEST mode, check each SW and VR. 7-6

  • Adjust or replace each SW and VR. SYSTEM 3. If the problem can not be solved yet, check the CONTROLS moves. 8

MONITOR In the MONITOR ADJUSTMENT mode, check to see if the 12

MONITOR adjustment is appropriately made.

IC BOARD1. MEMORY TEST7-2
  • In the SOUND TEST mode, check the sound related ROMs. 7-8

DATA CHECK Check such data as game play time and histogram to adjust the 7-15

difficulty level, etc.

Page 26

7-1 SWITCH UNIT AND COIN METER

specified. Touching places not specified can

@ Adjust to the optimum sound volume by considering the enviromental requirements of the installation location.

quirements of the installation location @ If the COIN METER and the game board are electrically disconnected, game

play is not possible. PORTANT!

Open COIN CHUTE DOOR, and the switch unit shown appears. The function of each switch is as follows:

SWITCH UNIT

  • SOUND VOLUME Controls the speaker volume of the right/left speakers.

(2) TEST BUTTON (TEST SW)

For the handling of the TEST BUTTON, refer to the section on test mode.

(3) SERVICE BUTTON (SERVICE SW)

Gives credits without registering on the coin meter.

SOUND VOLUME

DEMAGNETIZER SWITCH

TEST BUTTON SERVICE BUTTON

Page 27

7-2 SYSTEM TEST MODE

The contents of setings chnaged in the TEST mode are stored when the TEST mode is finished from EXIT in the MENU mode. If the power is turned off before the TEST mode is finished, the contents of

IMPORTANT! setting chnage become ineffective. Executing “BACKUP DATA CLEAR” in the SYSTEM TEST MODE does not clear the BOOKKEEP- ING data in the GAME TEST MODE.

Entering the TEST mode clears fractional number of coins less than one credit and BONUS ADDER, data.

The SYSTEM TEST mode mainly allows for IC Board functioning check, monitor adjustment, coin assignments, etc. For details, refer to NAOMI SERVICE MANUAL. The following assignments, however, should be designated for this product.

CABINET TYPE: 1 PLAYER (S) MONITOR TYPE: HORIZONTAL

COIN CHUTE TYPE: COMMON

7-3 GAME TEST MODE

MENU MODE

SYSTEM MENU CRAZY TAXI TEST MENU

RAM TEST INPUT TEST JVS TEST OUTPUT TEST SOUND TEST SOUND TEST C.R.T. TEST GAME ASSIGNMENTS SYSTEM ASSIGNMENTS VOLUME SETTING

COIN ASSIGNMENTS BOOKKEEP ING

BOOKKEEPING BACKUP DATA CLEAR BACKUP DATA CLEAR —> EXIT CLOCK SETTING

ROM BOARD TEST —> GAME TEST MODE (XXX KK KKK KKK XY EXIT SELECT WITH SERVICE BUTTON SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON AND PRESS TEST BUTTON

SYSTEM TEST MODE MENU GAME TEST MODE MENU

+ Press the TEST button to display the SYSTEM TEST MODE MENU. By pressing the SERVICE button, move the arrow (+) to select the GAME TEST MODE. Press the TEST button to enter GAME TEST MODE. The screen displays the GAME TEST MODE + MENU.

By pressing the SERVICE button, move the arrow (+) to select the desired item. Press the TEST button to + execute the selected item.

Select EXIT and press the TEST button to exit from the GAME TEST MODE and return to the SYSTEM

TEST MODE MENU. Further, select EXIT and press the TEST button to finish SYSTEM TEST MODE and return to the normal mode.

Page 28

7-4 INPUT TEST

Select INPUT TEST to have the screen shown below appear and to observe the status of each switch and the value of each V.R. on the Control Panel. Periodically check the status of each switch and V.R. on this screen.

INPUT TEST

DRIVE GEAR OFF REVERSE GEAR OFF

START, OFF

COIN CHUTE #1 OFF COIN CHUTE #2 OFF SERVICE OFF TEST OFF HANDLE 80H

ACCEL, 30H

BRAKE 30H

| PRESS TEST AND SERVICE BUTTON TO EXIT

FIG. 7.4 INPUT TEST

7-5 OUTPUT TEST

OUTPUT TEST

START LAMP ON

PRESS TEST BUTTON TO EXIT

FIG. 7.5 OUTPUT TEST @ By pressing each switch, if the display on the righthand side of the name of each switch changes to ON from OFF, the SW and the wiring connections are satisfactory.

To check CHUTE | & CHUTE 2 coin switches, open the COIN CHUTE DOOR and insert a coin(s) in the slot.

Press either the TEST BUTTON and the START BUTTON to return to the test menu.

Asa standard, refer to the following for each of the

Volume’s adjustment. By operating the Handle (Steering Wheel) and Pedal, if the V of each Volume guage smoothly moves as the corresponding value varies ina natural manner, then it is satisfactory.

Choose OUTPUT TEST to cause the following lower screen to appear. In this test, check the status of each lamp.

The right-hand side “ON” & “OFF” display of START

LAMP automatically alternates. The lamp lights up

when “ON?” is displayed and goes off when “OFF” is goes off in consistency with the display of “ON” and

displayed. Check to ensure that the lamp lights up and

“OFF”.

Press the TEST button to return to the TEST MENU.

Page 29

7-6 SOUND TEST

SOUND TEST

VOICE

EFFECT

BGM

>EXIT

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT

FIG. 7.6 SOUND TEST

7-7 C.R.T. TEST

CRILTEST 1/2 wn

WHITE WMA po | PRESS TEST BUTTON TO CONTINUE

fesfefstaobedatad cet FIG. 7.7 C.R.T. TEST This test mode allows each sound related board and speaker to be checked.

Press the Service Button to select the sound to be tested, and press the Test Button to have the selected Sound Test screen appear.

Select EXIT and press the Test Button to return to the Test Menu.

@ Select C.R.T. TEST to cause the MONITOR to display the screen shown left, allowing MONITOR adjustment status to be checked.

@ Periodically check the MONITOR adjustment status on this screen.

@ The screen (1/2) enables color adjustment check to be

performed. The color bar of each of the 4 colors,

ie.,red, green, blue, and white, is the darkest at the extreme left and becomes brighter towards the extreme right.

@ Press the TEST BUTTON to shift to the next screen (2/2).

@ The screen (2/2) allows screen size and distortion to be tested.

@ Check if the CROSSHATCH FRAME LINE goes out of the screen and if the crosshatch lines are distorted.

@ Press the TEST BUTTON to return to the MENU mode.

Page 30

7-8 VOLUME SETTING

When VOLUME SETTING is selected, the following appears on the screen and each operating unit’s Volume can be set.

If the operability is unsatisfactory, or when the Volume is adjusted or replaced, set the Volume in this mode. The 3 kinds of Volume Settings for HANDLE, ACCEL, and BRAKE are to be set. The Max. value, Min. value for each and the HANDLE’S CENTER value are to be set as applicable.

VOLUME SETTING

HANDLE SETTING AD0:78H

>EXIT

SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT

FIG. 7.8 VOLUME SETTING oe © © © Press the SERVICE button to select the Volume value to be changed.

Press the TEST button to cause the characters of the selected Volume value to turn red.

Input the value in the manner corresponding to the selected item.

Press the SERVICE buton to select EXIT, and press the TEST button to return to the MENU mode. At the same time the VOLUME SETTING is finished, the input values are stored as the Max. and Min. values.

Page 31

7-9 GAME ASSIGNMENTS,

Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and also the game settings changes (game difficulty, etc.) can be made. Each item displays the following content.

SETTING CHANGE PROCEDURE

@ Press the SERVICE BUTTON to move the “>” to the desired item. @) Choose the desired setting change item by using the TEST BUTTON. @) To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

GAME ASSIGNMENTS

START TIME 50 TIME DIFICULTY ais GAME DIFFICULTY 48

>EXIT

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON TO EXIT

@ START TIME This is the time alloted at the time of game start. Setting is possible starting from the shortest time sequentially in order of 35, 40, 45, 50, 55, -60, 65, and 70.

TIME DIFFICULTY Refers to the amount of BONUS TIME to be added when the taxi picks up the Customer. This can be set from 1/8 to 8/8 in 8 steps. The difficulty increases sequentially in order starting from 1/8.

GAME DIFFICULTY Sets the difficulty level in 4 categories, ie., EASY, NORMAL, HARD, and HARDEST.

Page 32

7-10 COIN ASSIGNMENTS,

The “COIN ASSIGNMENTS” mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses “how many coins correspond to how many credits.”

SETTING CHANGE PROCEDURE

E100 Setting changes cannot be stored unless the TEST BUTTON is pressed while the arrow is on EXIT.

IMPORTANT!

Oo) Press the SERVICE BUTTON to move the arrow to the desired item.

  • Choose the desired setting change item by using the TEST BUTTON.

® To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON.

7- 10 COIN ASSIGNMENTS

‘COIN ASSIGNMENTS

COIN/CREDIT SETTING #1

CHUTE! =1COIN 1 CREDIT

CHUTE. = 1COIN 1 CREDIT

ADDITIONAL SETTING MANUAL SETTING

>EXIT

SELECT WITH SERVICE BUTTON

AND PRESS TEST BUTTON

@ COIN/CREDIT SETTING Sets the CREDITS increase increment per coin insertion. There are 27 setings from #1 to #27, expressed in XX CREDIT as against XX COINS inserted. (TABLE 7.10a, 7.10b) #27 refers to FREE PLAY. When the COIN CHUTE TYPE is set to INDIVIDUAL, there are some setting numbers not displayed as indicated in TABLE 7.10b.

MANUAL SETTING This allows credit increase setting as against coin insertion to be further set in the manner finer than COIN/CREDIT SETTING (refer to TABLE 7.10c).

Page 33

TABLE 7.10a COIN/CREDIT SETTI

G (COIN CHUTE COMMON TYPE)

SETTING FUNCTIONING OF CHUTE#1

SETTING #11 COIN1 CREDIT
SETTING #21 COIN2 CREDITS
SETTING #31 COIN3 CREDITS
SETTING #41 COIN4 CREDITS
SETTING #51 COIN5 CREDITS
SETTING #61 COIN2 CREDITS
SETTING #71 COIN5 CREDITS
SETTING #81 COIN3 CREDITS
SETTING #91 COIN4 CREDITS
SETTING #101 COIN5 CREDITS
SETTING #111 COIN6 CREDITS
SETTING #122 COINS1 CREDIT
SETTING #131 COIN1 CREDIT
SETTING #141 COIN2 CREDITS
SETTING #151 COIN1 CREDIT

2 COINS 3 CREDITS

SETTING #161 COIN3 CREDITS
SETTING #173 COINS1 CREDIT
SETTING #184 COINS1 CREDIT
SETTING #191 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 5 CREDITS

SETTING #201 COIN5 CREDITS
SETTING #215 COINS1 CREDIT
SETTING #221 COIN2 CREDITS
SETTING #232 COINS1 CREDIT

4 COINS 2 CREDITS 5 COINS 3 CREDITS

SETTING #241 COIN3 CREDITS
SETTING #251 COIN1 CREDIT

2 COINS 2 CREDITS 3 COINS 3 CREDITS 4 COINS 4 CREDITS 5 COINS 6 CREDITS

SETTING #261 COIN1 CREDITS

SETTING #27 FREE PLAY

Page 34

MANUAL SETTING

Selecting MANUAL SETTING in the COIN ASSIGNMENTS mode displays the following screen.

MANUAL SETTING

COIN CHUTE #1 MULTIPLIER. a ee ®

COIN CHUTE #2 MULTIPLIER 1 COIN COUNTS AS 1 COIN cON 1 2 3 4 S$ 6 7 & 9 cREDIT 1020030 40 SGT

>EXIT

ERVICE BUTTON EST BUTTON

FIG. 7.11b MANUAL SETTING

@ Determines Coin/Credit setting.

@ This sets how many coins should be inserted to obtain one Service Coin.

@) This sets how many tokens one coin represents.

Table 7.10¢e MANUAL SETTING

COIN TO CREDIT 1 COIN 1 CREDIT 2 COINS 1 CREDIT 3 COINS 1 CREDIT 4 COINS 1 CREDIT 5 COINS 1 CREDIT 6 COINS 1 CREDIT 7 COINS 1 CREDIT 8 COINS 1 CREDIT 9 COINS 1 CREDIT

NO BONUS ADDER 2 COINS GIVE | EXTRA COIN 3 COINS GIVE | EXTRA COIN 4 COINS GIVE 1 EXTRA COIN 5 COINS GIVE 1 EXTRA COIN 6 COINS GIVE | EXTRA COIN 7 COINS GIVE | EXTRA COIN 8 COINS GIVE 1 EXTRA COIN 9 COINS GIVE 1 EXTRA COIN BONUS ADDER

COIN CHUTE MULTIPLIER 1 COIN COUNTS AS 1 COIN 1 COIN COUNTS AS 2 COINS 1 COIN COUNTS AS 3 COINS 1 COIN COUNTS AS 4 COINS 1 COIN COUNTS AS 5 COINS 1 COIN COUNTS AS 6 COINS 1 COIN COUNTS AS 7 COINS 1 COIN COUNTS AS 8 COINS 1 COIN COUNTS AS 9 COINS

Page 35

7 - 11 BOOKKEEPING

Choosing BOOKKEEPING in the MENU mode displays the data of operating status up to the present are shown on 2 pages. Press the TEST BUTTON to proceed to PAGE 2/2.

BOOKKEEPING PAGEL/3

COIN CHUTE #1 XXXXXXXXXXX, COIN CHUTE #2 XXXXXXXXXXX, TOTAL COINS XXXXXXXXXXX

COIN CREDITS XXXXXXXXXXX SERVICE CREDITS XXXXXXXXXXX TOTAL CREDITS XXXXXXXXXXX

NUMBER OF GAMES XXXXXXXXXXX

TOTAL TIME XDXXHXXMXXS PLAY TIME XDXXHXXMXXS

AVERAGE PLAYTIMEXXMXXS
LONGEST PLAYTIMEXXMXXS
SHORTEST PLAYTIMEXXMXXS

PRESS TEST BUTTON TO CONTINUE

FIG. 7.1la BOOKKEEPING (1/3) @ COIN CHUTE#: Number of coins put in each Coin Chute.

@ TOTAL COINS: Total number of activations of Coin Chutes.

@ COIN CREDITS: Number of credits registered by inserting coins.

In Page 2/3, Histogram of Number of Play as against Play Time is displayed. For setting the DIFFICULTY, refer to this histogram.

Page 3/3 displays the character’s selected frequency at the time of Game Start.

BOOKKEEPING PAGE 2/3

TIME HISTOGRAM BEGINNER ADVANCED EXPERT

ooo
ooo
ooo
ooo
ooo
o0o
ooo
o0o
ooo
ooo

PRESS TEST BUTTON TO EXIT

FIG. 7.11b BOOKKEEPING (2/3)

7-12 BACKUP DATA CLEAR

BACKUP DATACLEAR

YES (CLEAR) >NO (CANCEL)

SELECT WITH SERVICE BUTTON

FIG. 7.12 BACKUP DATA CLEAR BOOKKEEPING 3/3,

FAVORITE CHARACTER AXEL 0 BDJOE 0 GENA 0 Gus o

SELECT WITH SERVICE BUTTON

FIG. 7.11¢c BOOKKEEPING (3/3)

Clears the contents of BOOKKEEPING and high

score player ranking entry.

@ = When clearing, bring the arrow to “YES” and when

not clearing, to “NO”, by using the SERVICE BUTTON, and push the TEST BUTTON.

@ When the data has been cleared, “COMPLETED”

will be displayed. Bring the arrow to “NO” and press the TEST BUTTON to cause the MENU

mode to return on to the screen.

@ Note that the contents of the GAME SETTING, COIN SETTING, and BOARD SETTING are not

affected by BACKUP DATA CLEAR operation.

Page 36
  • HANDLE MECHA

@ [n order to prevent an electric shock and short circuit, be sure to tum power off before performing work by touching the interior parts of the product.

WARNING! @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit . accident.

In the test mode, if the steering wheel’s VR variations are not within the allowable range, the VR installation position adjustments or VR replacement is needed. Also, be sure to apply grease to the VR gear portion once every 3 months.

8 - 1 REMOVING THE CONTROL PANEL

Turn the power switch off. Remove a total of 4 tamperproof screws from both sides of the control panel’s front. Remove the two tamperproof screws fromthe underside of the control panel. Wiring connectors are connected inside the control panel. Carefully draw the control panel in a mnner so as not to damage wiring. ® SCO

Disconnect the wiring connector.

TAMPERPROOF SCREW (Black,

  • M8 X 30
Page 37

8 - 2 REPLACING AND ADJUSTING THE HANDLE’S VR

@ Never touch places other than those specified. Touching places not specified can cause electric shock and/or short circuit.

WARNING! @ After the replacement or adjustment of the VR, be sure to set the variable value of the VR in the test . mode’s Volume Setting.

REPLACING THE VOLUME

@) Tur off the power. @ Disconnect the connector. @ Take out the 2 screws which secure the volume Bracket and remove the Volume Bracket. ®@ Take out the 2 screws to remove the Volume Gear and replace the Volume. ® After replacing the Volume, perform Volume setting in the Volume Setting Mode.

ADJUSTING THE VOLUME

In the Test Mode, have the Volume value indicating screen displayed. Loosen the 2 screws which secure the Volume Bracket to disengage Gear Mesh. With the Steering Wheel in the centering position, cause gears to be engaged in the manner so that the Volume Shaft is in the status shown below.

Fasten screws which secure the Volume Bracket. ©O® CGO

Perform Volume setting as per the Volume Setting Mode.

T O)

SCREW (2) M4X8 | Tat & Spnag Waskers 0 |

—,

VR BRACKET “DP CUT FACE

Page 38

8 - 3 GREASING

@ Never touch places other than those specified. Touching places not specified can cause electric shock and/or short circuit.

WARNING! @ After the replacement or adjustment of the VR, be sure to set the variable value of the VR in the test . mode’s Volume Setting.

Apply greasing to the Volume gear mesh portion every 3 months. For spray greasing, use Grease Mate (Part No. 090-0066).

SPRING

SLIDING FACE OF CAM

Page 39
  • SHIFT LEVER

@ In order to prevent electric shock and short circuit, be sure to turn off the power before performing work on the interior parts of the product.

CAUTION! |] @ Be careful not to damage wiring. Damaged wiring can cause electric shock or short circuit. @ Do not touch places other than those specified. Touching places other than those specified can cause an electric shock or short circuit accident.

If the Shift Lever operation is not satisfactory, remove the Shift Lever in the following procedure and replace the microswitch.

9-1 REMOVING THE SHIFT LEVER

® Turn Power off. @ Take out the 4 SPECIAL BOLTS and pull the SHIFT LEVER UNIT upward by paying careful attention so as not to damage the wiring. @ Disconnect the 2 connectors to allow the unit to be removed. ® When reinstalling, follow the procedure oppisite as when removing. At this time, ensure that“DOWN” display appears on the upper part as shown.

TAMPERPROOF SCREW (4) M5 X12, black

Page 40

9-2 SWITCH REPLACEMENT

Each microswitch is secured with 2 screws. Remove the 2 screws and replace the Microswitch.

TAPPING SCREW (2)

a 7 GREASING

After replacing the Switch, check to see if the switch is inputted as per Shift Lever operation in the Test Mode.

Page 41

10. ACCEL & BRAKE(S)

@ In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short

WARNING! circuit accident. @ Do not touch places other than those specified. Touching places not specified can cause an electric shock or short circuit accident.

If Accel and Brake operation is not satisfactory, adjustment of Volume installation position or Volume replacement is needed. Also, be sure to apply greasing to the gear mesh portion once every three months.

10 - 1 ADJUSTING AND REPLACING THE V.R.

When released: When stepped on: Under 30 H Over COH Under 30 H Over COH

Check Volume values in the Test Mode. Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated portions. Touch-

TRUSS SCREW (2)

ing places not specified can cause an electric shock or short circuit. MAX E, chrome

®O Take out the 2 truss screws and remove the Front Cover from the Accel. & Brake unit

from the Accel. & Brake unit. @ Loosen the screw which secures the Potentiobase, and adjust the Volume Value by moving the Base. @ Secure the Potentiobase. @ Perform Volume setting in the Volume Setting Mode.

FRONT COVER

Page 42

Check Volume values in the Test Mode.

Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated portions. Touching places not TRUSS SREV (2) Wi x specified can cause an electric shock or short circuit.

Take out the 2 truss screws and remove the Front Cover

from the Accel. & Brake unit.

Loosen the screw which secures the Potentiobase, and adjust the Volume Value by moving the Base. Secure the Potentiobase. ©© © © Perform Volume setting in the Volume Setting Mode.

POTENTIORASE

10 -2 GREASING 5 POTENTIOCOVER

S

IMPORTANT!

Once every 3 months, apply greasing to the Spring and Gear Mesh portion. For spray greasing, use GREASE MATE (PART No. 090-0066).

Page 43
  • COIN SELECTOR

HANDLING THE COIN JAM

If the coin is not rejected when the REJECT BUTTON is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions.

CLEANING THE COIN SELECTOR

©

6)

© The coin selector should be cleaned once every 3 months. When cleaning, follow the procedure below: Turn the power for the machine OFF. Open the coin chute door.

Open the gate and dust off by using a

soft brush (made of wool, etc.). Remove and cleen smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Remove the CRADLE. When removing the retaining ring(Ering), be very careful so as not to bend the shaft. Remove stain from the shaft and pillow

portions by wiping off with a soft cloth,

etc. After wiping as per #5 above, further apply a dry cloth, etc. to cause the coin selector to dry completely. FIG. lla

@ Never apply machine oil, etc. to the coin selector @ Afier cleaning the Coin Selecting, Insert a

IMPORTANT! regular coin in the normal working status

and ensure that the Selector correctly functions.

COIN INSERTION TEST Once a month, when performing the COIN SW TEST, simultaneously check the following:

O Does the Coin Meter count satisfactorily? O Does the coin drop into the Cashbox correctly? O Is the coin rejected when inserted while keeping the REJECT BUTTON is pressed down? Insert a coin, while keeping the Reject Button pressed down and check if it is rejected.

COIN METER

FIG. lle

Page 44

FUNSOTONA WIDAdS YOOd WOLLOG §=§=YxOLVNVA TH HLIM S3dLN3 YOO INI Y3GNN/Y LO-OLL2-S LGOM

by @ AO

WNOO"239M ANA 0€99-9EE-0081 6€909 I OSVIIH) 3YVCTIN'N LOdzZ NOLLVYOdYOD SIINOYLOITS YANGYV9-STIIM

Page 45

Tom Happ

tom.happ@happcontrols.com

HAPP CONTROLS

106 Garlisch Drive Ek Grove, IL, 60007 Ph. 847-593-6161 ext. 107 Fx, 847-956-209]

Visit owe website http://wew.hoppeantrols.com

Page 46

OPTIONAL DOLLAR BILL ACCEPTOR

@TH

TH

HO.

HO.

HO.

HO. S APPL

LE POS

LE POS

LE POS

LE POS E COIN DOO.

EQUIPPED TO ACCEPT A DOLLAR BILL ACCEPTOR. ALL NEEDED WIRING CONNECT. ONS

CAT

TIO.

TIO.

TIO.

TIO. R ASSEMBLY USED ON CRAZY TAXI STANDARD COMES

ARE CONVIENENTLY LOCATED INSIDE THE GAME FOR

ON.

@ THE COIN DOOR CAN ACCCOMMODATE THE FOLLOWING VALIDATORS:

#1 Mars 2000 series

(FORWARD-MOST POSITION)

#2 Mars 2000 series

DBV45 (JCM)

#3 CURRENTLY NOT USED

bd DSIO1*

*The back flange on the chute can be removed for hold position #4. If the flange is not removed, it may interfere with the back of the cabinent.

The frame and cashbox enclosure on this coindoor has been modified to accomodate a Mars 2000 series upstacker. A 2000 series stacker can be added by simply removing the top two entry door and replacing it with a one entry door with a cut-out for a stacker. This one entry door can be ordered through Coin Controls or one of Coin Controls authorized distributors. The part number is 91-4000-01. The Mars stacker can be obtained through an autherized Mars distibutor.

4l www.seuservice.com

Page 47
  • MONITOR

When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from monitor, be sure to disconnect the power connector (plug) before starting work. Proceeding the work without following this instruction can cause electric shock of malfunctioning. Using the monitor by converting it without obtaining a prior permission is not allowed. SEGA shall not be liable for any malfunctioning and accident caused by said conversion.

Primary side and secondary side The monitor’s circuit which is divided into the Primary side and secondary side, is electrically isolated. Do not touch the primary side and the secondary side simultaneously. Failing to observe the instruction can cause

electric shock, and this is very dangerous. When making Ncomnc en SIDE

monitor adjustments, use a non-conductive driver and make adjustment without touching any other part other PRIMARY than the Adjustment V.R. and Knob. Also, be sure not to SIDE cause a short-circuit to the Primary side and the Secondary side. If short-circuited, it can cause electric shock or

malfunctioning, which is very dangerous. @

High tension Voltage Some of the parts inside the monitor are subject to high-tension voltage in excess of 20,000 volts and very dangerous. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor, tum the power off so as not to cause malfunctioning or fire hazard.

® ANODE CAP PRIMARY SIDE DEMAGNETIZER REAR PART

com ? ANODE LEAD MAIN BD ‘Approx. 29 kV

DEMAGNETIZE! ® FOCUS LEAD

COIL (black) Approx. 10 kV

SECONDARY SIDE ' FBT Approx. (Chassis, sheet metal work, CRT, etc.) Disconnect or unplug 29kV

Connecting the CRT and PCB For combining the CRT and PCB, use the specified part No. to maintain the status of adjustments made at the factory. The anode of the CRT itself will be accumulitavely charged as time elapses, generating high tension voltage which is very dangerous. The monitor should be used with the Chassis, CRT and PCB assembled. When repair, etc. is required at the time of malfunctioning, be sure to send it in an “as assembled” condition. If these are disassembled, what’s charged to said high tension voltage can be discharged, causing a very hazardous situation. Therefore, under no circumstances should it be disassembled.

Static Electricity Touching the CRT surface sometimes causes you to slightly feel electricity. This is because the CRT surfaces are subject to static and will not adversly affect the human body. Installation and removal Ensure that the Magnetizer Coil, FBT (Fly-Back Transformer), Anode Lead and Focus Lead are not positioned close to the sheet metal work’s sharp edges, etc. and avoid damaging the insulated portions so as not to cause an electric shock and malfunctioning. (For the name of parts, refer to the above figures.)

Page 48

For the purpose of static prevention, special coating is applied to the CRT face of this

CAUTION! product. To protect the coating, pay

attention to the following points. Damaging the coating film can cause electric shock to the customers. For the caution to be heeded when clearing, refer to the Section of Aluminum Foil Periodic inspection Table. Do not apply or rub with a hard item (a rod with pointed edge, pen, etc.) to or on C.R.T. surfaces. Avoid applying stickers, seals, etc. on the C.R.T. face. Do not remove aluminum foils from the C.R.T. corners. Removing the aluminum foils can cause static prevention effects to be lowered.

Monitor adjustments have been made at the time of shipment. Therefore do not make further adjustment without a justifiable reason. Adjusting the monitor which contains

CAUTION! high tension parts is dangerous work. Also, an erroneous adjustment can cause deviated synchronization and image fault, resulting in malfunctioning. When making adjustment, utilize a resinous Alignment Rod. Servicing with bare hands or using conductive tools can cause electric shock.
Page 49

SANWA Monitor: 998-0156 (31K Mode)

—,

[| OO / oe id CONTRAST — BRIGHT HSIZE HPOS! VSIZE VPOSI

@) CONTRAST.......00..... Adjust image contrast. @) BRIGHT.........0............ Controls screen brightness.

  • H. SIZE... Controls horizontal screen size.
  • H. POSL.... Controls horizontal display position on screen. G) V. SIZE... Controls vertical screen size. (©) Wi POSE vivsscssiacareons! Controls vertical display position on screen.
Page 50
  • REPLACEMENT OF FLUORESCENT LAMP

on can cause an electric shock or short circuit accident. "» @ When performing the work, be sure to turn power off. Working with power

WARNING: @ The Fluorescent Lamp, when it gets hot, can cause burns. Be very careful when replacing the Fluorescent Lamp.

and stable condition. Not using a step or using an unstable step can cause violent M To perform work safely and securely, be sure to prepare a step which is in a secure falling down accidents.

CAUTION!

13 -1 REPLACEMENT OF FLUORESCENT LAMP.

® Take out the 3 Tamperproof screws from the rear of the billboard.

@ Be sure to disconnect all connectors conected to the Marquee assembly before removing the Billboard and/or performing work.

® Take out the two screws which secure the lower billboard plate mask and remove billboard

W (3) PER PROOF TOP SASH

BILLBOARD \ LFLOURESCENT LAMP 20W. White “TOCAL PURCHASE

Page 51
  • PERIODIC INSPECTION TABLE The items listed below require periodic check and maintenance to retain the performance of this machine and ensure safe operation.

@ Be sure to check once a year to see if Power Cords are damaged, the plug is securley inserted, dust is accumulated between the Socket Outlet and the Power Plug, etc. Using the product with dust as is accumulated can cause a fire or electrical shock.

WARNING! e Periodically once a year, request the place of contact herin stated or the Distributer, etc. where the product was purchased from, as regards to the interior cleaning. Using the product with dust as is accumulated in the interior without cleaning can cause a fire or short circuit accident. Note that cleaning the interior parts can be performed on a pay-basis.

ITEM INTERVAL REFERENCE

CABINETCheck Adjusters’ contact with surface.Daily4
HANDLE MECHACheck lamp.Monthly8
Check VOLUME VALUE.Monthly8
Check ADJUST GEAR engagement.Tri-Monthly9
Greasing of GEAR.Tri-Monthly9
ACCEL. & BRAKECheck VOLUME value.Monthly10
Check ADJUST GEAR engagementTri-Monthly10
Gear and Spring portion greasing.Tri-Monthly10
SHIFT LEVERCheck Switches.Monthly9
COIN CHUTE TOWER | Check COIN SW.Mont!4

Coin insertion test. Mont i

Cleaning of COIN SELECTOR.Tri-Monthlyi

MONITOR Check adjustments. Monthly or when moving 12

Cleaning of CRT surfaces.Weekh12
SEATAntistatic measures.Bi-MonthlyNext page

Applying grease to Seat Rail. Tri-Monthly

GAME BDMEMORY TEST.Monthly7
Check Settings.Monthly7

CABINET SURFACES | Cleaning As occasion arises | Next page

INTERIOR Cleaning ‘Annually See Above

POWER SUPPLY PLUG | Inspection and cleaning.

CLEANING CABINET SURFACES

Ifthe cabinet is badly stained, use a cloth which is dipped in the chemical detergent liquid diluted with water and then squezzed dry. Do not use thinner, benzine, alcohol or chemical dustcloth as these can damage Cabinet surfaces.

SEAT (Greasing to Seat Rail Portion) ao

Move the Seat to the rearmost portion and apply spray greasing to the _-, portion shown at the right once every 3 months by using NOK KLUBER L60 or GREASE MATE SEGA PART No. 090-0066. After greasing, move seat a few times forward and backward so as to allow the grease to be applied all over uniformly. Be sure to wipe grease which attaches to the surfaces of the PROTECT RUBBER on the seat Rail, or any excess grease.

Page 52
  • TROUBLESHOOTING Should trouble occur, first check connector connections.

PROBLEMS CAUSE COUNTERMEASURES

With Main SW ON, no activation Power is not supplied.

Power supply/voltage is not correct.

AC main fuse causes the

power to be cut off due to momentary

overload. Plug in correctly

Make sure that power supply/voltage is correct. Check fuse. Remove the cause of overload and replace fuse

Operation is unsatisfactory Volume Setting Failure

Poor mesh of V.R. gear.

Spring failure due to secular change of Accelerator and Brake Mecha. Perform Volume setting Adjust or replace V.R.

Adjust Gear mesh..

Replace the Spring.

Irregular sound emitted from inside Rear Cabinet Greasing to gear mesh portion is not satisfactory, or extraneous matter mixed in. Apply greasing or eliminate extraneous matter.

The color of the image on PROJ. screen is incorrect.

The image on PROJ. screen has color deviation. Connector connections are defective.

Affected by the magnetic field of installation location. Check the connection for the RGB and SYNC connectors of the PROJ. TERM. BD and VPM BUFFER BD.

Make CONVERGENCE adjustment. (Refer to Section 12.)

No sound is emitted. Sound Volume adjustment is not appropriate.

Sound BD and speaker are malfunctioning. Adjust sound volume. (see Section 7).

Perform sound test to find and replace defective parts.(Refer to Section 7).

NETWORK check will not finish. Communication cable’s connection failure. Perform V.R. setting, Adjustment.

Communication play is not possible. Communication cable’s connection failure. Communication Play setting is wrong. Check for Communication cable disconnection Correctly set in test mode.

No sound from Cockpit. In correct Cabinet Type Setting. Correct Cabinet Type Setting.

The Fluorescent lamp does not light up. The Fluorescent tube is burt out. Replace the Fluorescent tube (Refer to Section 11).

Shift operation is not is not satisfactory in Manual transmission. Shift SW malfunctioning. Replace SW

Page 53
  • GAME BOARD

@ In order to prevent an electrical shock, be sure to turn power off before performing work by touching the interior parts of the product.

WARNING! © Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circuit accident.

Do not expose the Game BD, etc. without a good reason. In this product, setting changes are made during the test mode. The Game BD need not be operated. Use the Game BD, ete. as is with the same setting made at the time of shipment.

CAUTION!

16-1 REMOVING THE GAME BOARD

To replace the IC Board or to change dip switch settings, take out the IC board using the following procedure;

Turn main switch off.

Unlock the base, and remove the 2 truss screws from the side of the base. Turn the knob to unlock. The seat can be inclined in the direction shown. When inclining the seat, be careful not to damage seat parts. Carefully rest the backrest portion of the seat on the ground. If neccessary, protect the seat from damage by using a cloth or blanket on the floor. Take off the 3 screws to remove the case lid. The game board is inside the shield case. G08 C080

Take off a total of 4 screws from both sides with the seat being in an inclined state and remove the base lid F. Removing base lid F allows the Elec Base to be seen.

INCLINE THIS CAREFULLY.

TRUSS HEAD SCREW (4) >> MS X 12, Black

MS X, BLACK

Page 54

16 -2 REPLACEMENT OF FUSE

@ In order to prevent an electric shock, be sure to turn power off before performing work by touching the interior parts of the product.

WARNING! @ Be careful so as not to damage wirings. Damaged wiring can cause an electric shock or short circiut accident @ A fier eliminating the cause of the blowing of fuse, replace the fuse. Depending on the cause of the fuse blowing, using the fuse as is blown can cause generation of heat resulting in fire.

Incline the Seat and remove the Base Lid to view the Base interior. The composition of the Base interior is as shown below. There is a fuse on each of the Connect BD. and Motor Drive BD. When replacing the fuse, be sure to use the specified one.

FUSE SA LOCAL PURCHASE

CONNECT f {

Page 55

16 -3 COMPOSITION OF GAME BOARD

Ensure that the DIP SW setting is performed as designated as designated. Failure to observe this may cause functioning not suitable for the operation, or malfunctioning.

IMPORTANT!

ASSY CASE NAO USA (840-0002D-01) :USA

SCREW (4) ao

ROM CASE NAO CT 344-0002C

DIP SW

DIP SW SETTING

IN the product, set all of the DIP SWes to OFF.

Page 56
  • DESIGN RELATED PARTS

ITEM NO. PART NO.

DYN-0011 LOCAL PURCHASE 999-0771 999-0770 SPG-1201-E DYN-1214-C DYN-1214-D DYN-1214-E SPG-2002 999-0773 999-0772 999-0769 999-0768 999-0767 999-0761 999-1378 999-1379 999-1380 DESCRIPTION

DENOMI PLATE W/O ORIGINAL DENOMINATION SHEET | GAME STICKER INSTRUCTION SH CTA STICKER SUB INSTR SH CTA METER PANEL DESIGN PL TACO MTR TWIN DESIGN PL OIL MTR TWIN DESIGN PL WATER MTR TWIN STEERING EMBLEM STICKER MONITOR COVER L CTA STICKER MONITOR COVER R CTA STICKER MAIN BASE L CTA STICKER MAIN BASE R CTA STICKER MAIN BASE C CTA MARQUEE PLEX CRAZY TAXI DECAL SEAT BK SEGA LOGO DECAL SEAT BK CRAZY TAXI LOGO DECAL SEAT BK CHECKR BRD PATTERN

Page 57
  • PARTS LIST

TOP ASSY CRAZY TAXI

ITEM NO. PART NO. DESCRIPTION

1DUT-10001ASSY COCKPIT 1P
2DUT-11001ASSY COCKPIT 2P
3DUT-0200ASSY BILLBOARD
4SPG-0300ASSY COIN CHUTE TOWER
5422-0661-01SUB INSTR SH SRT TWIN ENG
15421-8543STICKER CABINET L
16421-8544STICKER CABINET R
17421-7308~DENOMINATION SHEET 1GAME~
19DUT-0001BLIND CAP
20SPG-0006AC COVER A
21DYN-0006XAC COVER B
22IN Y-0004BACK LID INY
23DYN-0008BACK LID B
24DYN-0009HOLE LID
25DYN-O0011DENOMI PLATE W/O ORIGINAL
27429-0623DISPLAY CARD DUT TWIN
28DUT-0002POP BRKT
29DUT-0003BILLBOARD BASE
30DUT-0004CONNECTOR COVER
31DUT-0005BILLBOARD HOLDER
101600-6275-0500ASSY FIBER CABLE 5 0500CM
Page 58

ASSY BILLBOARD STD (999-0774)

ITEM NO. PART NO. DESCRIPTION

1 999-0761 MARQUEE PLEX CRAZY TAXI 2 999-0733 LOWER MARQUEE GRILL 3 999-0731 MARQUEE COVER L 4 999-0732 MARQUEE COVER R 101 LOCAL PURCHASE ASSY FL 20W EX W/CONN HIGH S 102 DRT1-0230 LAMP UNIT 103 DRT1-0240 SKT UNIT

Page 59

ASSY COINCHUTE TOWER (DUTS-0300)

Page 60

ASSY COINCHUTE TOWER (DUTS5-0300)

ITEM NO.

SDT Svaene PART NO.

SPG-0350 SPG-0301 DYN-0302Y DP-1167 BOX-CASH DYN-0305 105-5202 SPG-0302 SPG-0303 LOCAL PURCHASE 220-5412 220-5412-01 220-5574 220-5575 DESCRIPTION

SW UNIT COIN CHUTE TOWER COIN METER BRKT TNG LKG CASH BOX TOWER BRKT HOLE COVER WIRE BOX WIRE BOX LID COIN DOOR ASSY MAG CNTR W/CONN MAG CNTR W/CONN BLACK CAM LOCK W/KEYS CAM LOCK MASTER W/O KEY

  • This coin door is produced by Coin Controls and can be ordered through your local distributor.
Page 61

SW UNIT (SPGS5-0350)

SOUND VOLUME

ITEM NO. PART NO. DESCRIPTION

1SPG5-0351SWITCH BRKT
101509-5028SW PB IM

102 220-5179 VOL CONT B-5SK OHM

103601-0042KNOB 22 MM
104LOCAL PURCHASEMAG CNTR W/CONN

105 509-5453-91-V-B ROCKER SWJ8 V-B

Page 62

AC UNIT (DRT 1-0400)

ITEM NO. ° °

fe) fe)

PART NO. DESCRIPTION

DUT-0401 AC BRKT

600-5843-25 CA & PLUG ASSY 15A W/F-L=2.5M 280-5 134-6N34 512-5046-15000 509-5453-91-V-B 280-0417 BUSHING STRAIN RELIEF 6N34 C.P 15000mA CE UL SW ROCKER J8 V-B TERMINAL BINDING POST BLACK

Page 63

ASSY MONITOR COVER R IP.

SECTION A-A

ITEM NO. PART NO. DESCRIPTION

1 DRT5-1046 COVER PANEL R 1P 2 130-5156 SPEAKER BOX

Page 64

ASSY MONITOR COVER L 1P

WWW

SECTION A-A

ITEM NO. PART NO. DESCRIPTION

1 DUTS5-1031 COVER PANEL L BLACK

130-5156 SPEAKER BOX

Page 65

ASSY VIRTUAL BUTTON TWIN (DRT5-1290)

ITEM NO. PART NO.

DRTS-1291 171-6478B 212-5205-12 509-5560-Y DESCRIPTION

VR BUTTON BRKT PC BD LIGHTING SW CONN JST M 12PRTA PB SW WIL 6V ILY

Page 66

ASSY BASE BOX (DRT 1-1500)

ITEM NO. PART NO. DESCRIPTION

1DRT1-1501MAIN BASE
2DYN-2003BASE LID F
3DYN-2004LOCK TNG

4 DYN-2005X FLOOR MAT 6 DRT-1510 ASSY BASE LIDR 8 DYN-2009X LID EDGER

5DYN-2006HINGE 480
7DYN-2007XLID EDGE L

101 220-5575 CAM LOCK MASTER W/O KEY

Page 67

MAIN BASE (DRT1-1501)

ITEM NO. PART NO. DESCRIPTION

1 DYN-2002X-A MAIN BASE BLANK

2999-0769STICKER BASE L
3999-0768STICKER BASE R

4 999-0167 LEG ADJUSTER BOLT 1/2X13X3

5999-0169CASTER 2 1/2"
Page 68

ASSY SEAT TWIN 1P (DRT-1600)

E

& g

= M8 Others: 195kgf-cn

Page 69

ASSY SEAT TWIN IP (DRT-1600)

ITEM NO. PART NO.

1 STC-1650 2 DUT-2202 3 DUT-2203 4 STC-2201 5 STC-1604 6 DUT-1601 DUT-1701 7 STC-1606 8 STC-1607 9 STC-1608 10 STC-1609 11 STC-1610 12 STC-1611 13 STC-1612 14 STC-1613 15 INY-1302-B 101 601-9059 102 601-9060 103 130-5162-01 105 601-6563-188 106 601-6563-100 107 280-5297 201 000-P00410-W 203 030-000816-S 205 050-H00800 206 060-S00800 210 000-T00616-0B 211 010-P00408-F DESCRIPTION

ASSY WOOFER UPPER SEAT LOWER SEAT SEAT BASE SEAT FRAME SEAT REAR COVER IP SEAT REAR COVER 2P SEAT MOUNT TRAY SP MOUNT BRKT SPEAKER NETL SPEAKER NET R SAFETY GUARD CABLE BEAR BRKT PROTECT RUBBER SAFETY GUARD F MASK CUSHION SIDE SEAT RAILL SEAT RAILR GULL BOX SPEAKER 800HM SW BUSH 2.4T BUSH 2.4T SCRIVET 8 1K31 M SCR PH W/FS M4X10 HEX BLT W/S M8X16 HEX NUT M8 SPR WSHR M8 M SCR TH BLK M6X16 S-TITE SCR PH W/F M4x8

Page 70

WLOI‘AIIAAASNISMMM S9 (007Z-DdS) TAVUAVTAIOV ASSV

Page 71

ASSY ACCEL&BRAKE (SPG-2200)

ITEM NO. PART NO. DESCRIPTION

1SPG-2201BASE
2SPG-2202ACCEL PEDAL
3SPG-2203BRAKE PEDAL
4SPG-2204ACCEL SPRING
5SPG-2205BRAKE SPRING
6SPG-2206SHAFT
7SPG-2207ACCEL GEAR
8SPG-2208BRAKE GEAR
9SPG-2209NUETRAL STOPPER
10SPG-2210VR PLATE ACCEL
11SPG-2211VR PLATE BRAKE
12SPG-2212AMPL GEAR
13SPG-2213GEAR SHAFT
14SPG-2214STOPPER
15SPG-2215RUBBER CUSHION
16SPG-2216COVER
17SPG-2217VR COVER
19SPG-2219GEAR STAY
20SPG-2220WSHR
21SPG-2221NUETRAL STOPPER
101100-5263BEARING 12
102220-5484VOL CONT B-5K OHM
104601-7944GEAR 15
105310-5029-F15SUMI TUBE F F 1SMM
106280-0419HARNESS LUG

201 028-A00304-P SET SCR HEX SKT CUP P M3X4 202 020-000520-0Z HEX SKT H CAP SCR BLK M5X20

203000-P00420M SCR PH M4X20
204000-P00508-WM SCR PH W/FS M5X8
205000-T00408-0CM SCR TH CRM M4X20
206FAS-450005SPR PIN BLK OZ 6X10
207000-P00405M SCR PH M4X5
208FAS-000001M SCR TH CRM M3X6
209050-H00500HEX NUT M5
210060-F00400FLT WSHR M4
Page 72

ASSY HANDLE MECHA (CTA-2100)

Page 73

ASSY HANDLE MECHA (CTA-2100)

ITEM NO. PART NO.

1 CTA-2101 2 CTA-2101 3 CTA-2103 4 CTA-2104 5 CTA-2105 6 CTA-2106 7 CTA-2107 8 DYN-1262 9 DYN-1269 10 DYN-1273 11 BVG-1340 12 BVG-1341 13 SLC-1130 14 SLC-1141X 1S SOR-2112 16 SOR-2113 17 SOR-2115 18 SPG-2109 19 601-6172 20 601-6959 21 601-8966 22 SLC-1108

101 100-5018 102 100-5112 103 100-5041 104 220-5484

201 028-A00408-P 202 028-A00308-P 203 FAS-650011 204 000-P00408-W 205 000-P00412-W 206 060-F00600 207 050-U00600 208 060-F00800 209 050-U00800 210 065-E00700 211 060-S00800 DESCRIPTION

HANDLE BASE BASE LID HANDLE SHAFT STOPPER BOLT SPRING HOOK SPACER RING VR BRKT SWING ARM SHAFT EXT SPRING SWING ARM FLT WSHR 8.1-12X2 FLT WSHR 4.1-12X2 ADJUST RING WHITE CAM BEARING SHAFT SPACER KEY 5X10 STOPPER RUBBER GEAR 48 GEAR 64 GEAR HOLDER WIRE HOLDER

BEARING BALL 8 BEARING 17 BEARING NSK F688 ZZ VOL CONT B-5K OHM

SET SCR HEX SKT CUP P M4X8 SET SCR HEX SKT CUP P M3X8 STP RING BLK OZ S17 M SCR PH W/FS M4Xx8 M SCR PH W/FS M4X12 FLT WSHR M6 U NUT M6 FLT WSHR M8 U NUT M8 E RING 7MM SPR WSHR M8

Page 74

ASSY SHIELD CASE NAO (840-0002D-01)

ITEM NO. PART NO. DESCRIPTION

1 840-0001A-01 SHIELD CASE CTA NAO USA CTA 840-0001C ROM CASE NAO

Page 75

ASSY GAME BD

ITEM NO. PART NO. DESCRIPTION

1 400-5397-01 POWER SUPPLY

840-0002D-01 ASSY SHIELD CASE NAOMI CTA

Page 76

ASSY ELEC BASE (CTA1-4500-02)

ITEM NO. PART NO.

NOT AVAILABLE

998-0146 LOCAL PURCHASE LOCAL PURCHASE LOCAL PURCHASE

838-13616 838-13683-01 DESCRIPTION

WOODEN BASE ELEC

XFMR 04-06-8036 LINE FILTER FUSE BLOCK W/ FUSES GROUND PLATE

AMPLIFIER VO BD

Page 77

ASSY COCKPIT 1P (DRT 1-10001)

. . <= SSS =

e a Z =

Details of PART B

*01)(108)(106)(07)

Page 78

ASSY COCKPIT 1P (DRT1-10001)

ITEM NO. PART NO. DESCRIPTION

1DUT-20001ASSY MAIN BASE IP

DUT-21001 ASSY MAIN BASE 2P

2DUT-1030ASSY MONITOR COVER L IP

DUT-1040 ASSY MONITOR COVER L 2P

3DUT-1035ASSY MONITOR COVER R IP

DUT-1045 ASSY MONITOR COVER R 2P 4 DUT-12001-01 ASSY CONTROL PANEL TWIN EXP

5SPG-1004MONITOR STAND
6SRT-1002WIRE COVER BOX
7INY-1016MONITOR SUPPORT

8 SPG-1008 ROOF LID

9TTR-1067XMONITOR MASK
10SPG-1005MASK HOLDER
llDYN-1025RUBBER CUSHION
12INY-1015CRT ADJUST PANEL
14DUT-4550ASSY DRIVE BD TWIN
101200-5242-24-04ASSY CLR DSPL 29 TYPE 100V

200-5243-24 ASSY CLR DSPL 29 TYPE 24K 100V

105280-5112BUSH FOR TV
106280-5113COLLAR FOR TV
107280-5114SPACER 6.4-25x2
108280-5185-6SPACER TUBE L=6
109601-6231-C100EDGING NEW TYPE
Page 79

ASSY CONTROL PANEL (DRT1-1200-02)

Page 80

ASSY CONTROL PANEL (DRT1-1200-02)

ITEM NO. PART NO.

DYN-1201 DYN-1209X SPG-2002 DRTI -1201-01 SPG-1205 INY-1204 DYN-1223X SPG-1204 CTA-2100 610-0384 DRT5-1290 SPG-2039

020-000820-0Z 060-F00800 060-S00800 050-H00800 FAS-200013 000-T00416-0B 000-P00412-W 008-T00516-0B 030-000820-S 000-T00412-0C DESCRIPTION

STEERING WHEEL HANDLE COLLAR STEERING EMBLEM CONTROL PANEL COVER ENG CONTROL PANEL BRKT SHIFT COVER INY SHIFT COVER B SPL BLT M8 ASSY HANDLE MECHA ASSY SHIFTER ASSY VIRTUAL BUTTON CTA SPACER RING

HEX SKT H CAP SCR BLK OZ M8X20 FLT WSHR M8 SPR WSHR M8 HEX NUT M8 HEX SKT H CAP SCR CRM M4X16 M SCR TH BLK M4X16 M SCR PH W/FS M4X12 TMP PRF SCR TH BLK M5X16 HEX BLT W/S M3X12 M SCR TH CRM M4X12

Page 81

ASSY MAIN BASE 1P (DRT5-20001)

N8_195kgf-cm

TORQUE: NG 84kef+cm

Page 82

ASSY MAIN BASE 1P (DRT5-20001)

ITEM NO. PART NO. DESCRIPTION

1 SRT-1500 ASSY BASE BOX

2 SRT-1600 ASSY SEAT TWIN IP

SRT-1700 ASSY SEAT TWIN 2P

3SPG-2200ASSY ACCEL&BRAKE

4 SRT-4400 ASSY MAIN BD BASE

5 SRT-4500 ASSY ELEC BASE

6SRT-0400-01AC UNIT MAIN EXP (IP)

SPG-0700 AC UNIT SUB (2P)

7SPG-1502PEDAL BASE

8 RAL-2007 RUBBER HOLDER R TWIN

9RAL-2008RUBBER HOLDER L TWIN
10SPG-1503FAN BRKT

101 260-0011 AXIAL FLOW FAN AC100V 50-60 HZ

102600-6275-0150ASSY FIBER CABLE 5 0150CM
Page 83
  • WIRE COLOR CODE TABLE

THE WI

moawe RE COLOR CODE is as follow:

PINK

SKY BLUE

BROWN

PURPLE

LIGHT GREEN

Wires other than those of any of the above 5 single colors will be displayed by 2 alphanumeric characters.

CwrrIneEwWwnNe RED

BLUE

YELLOW

GREEN

WHITE

ORANGE

BLACK

GRAY

If the right-hand side numeral of the code is 0, then the wire will be of a single color shown by the left-hand side numeral (see the above).

Note 1:
Note 2: If the right-hand side alphanumeric is not 0, that particular wire has a spiral color code. The left-hand side character shows the base color and the right-hand side one, the spiral color.

<Example> 51............. WHITE / RED

NOON ON

RED WHITE

The character following the wire color code indicates the size of the wire.

U: AWGI6

K: AWGI8

L: AWG20

None: AWG22

Page 84

Warranty

Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. No other product in this machine is hereby covered.

Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. For Warranty claims, contact your Sega Distributor.

Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void.

Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages.

This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above.

Page 85

SEGA ENTERPRISES, INC. (USA)

45133 Industrial Drive Fremont, CA 94538 (415) 701-6580 phone (415) 701-6594 fax