CATHODE RAY TOMES

Pac-Man MsPac-Man Troubleshooting Logic Board Part 2

Pac-Man & Ms. Pac-Man (Midway Manufacturing Company, 1982) · Troubleshooting · 71 pages · 27 sections · original scan

Page 1

MIDWAY’S

PAREMAN) « (PR-MAN

TROUBLE SHOOTING LOGIC BOARD

PART II

COCKTAIL #933

ee UP-RIGHT #595 ~ MINI #934 : a PHONE: Csally|MIDWAY PHONE: (312) 451-9200 10601 WEST BELMONT AVENUE TOLL FREE TELEX 72-1596 FRANKLIN PARK, ILLINOIS 60131 800-323-7182 FORM—00238—8204 U.S.A.

Page 2

Asensational, full color video game for 1 or 2 players that tickles vision and challenges reflexes. Adding to the fun are musical refrains, chomping and action sounds along with amusing cartoon shows between racks.

HIGH SCORE — Retained and displayed daily.

The player,FauniojPLAYERS’ SCORE
using a singleHi——DOTS — 10 Points Each.

handle control

guides thezPOWER CAPSULE —

PAC-MAN about the maze, 50 Points Each. scoring points by munching up : ,

the Dots in his path. Four Ghost::.ce|___GHOST MONSTERS
eeeeeeOAC MAN;|_-PAC-MAN — The ‘main’ man.
trying to capture and deflate him.=:.7-_

that enables him to overpower the BONUS FRUIT TARGET —

Monsters for additional score.,Appear below Monster’s Den

After all the Dots are gobbled 3 twice during each rack. i up, the screen is cleared, and : x i

PAC-MAN continues for another2—NUMBER OF SCREENS
round. Each rack features a?1CLEARED — Fruit indicates

special Fruit Target in the maze, how many times player has

which if eaten, earns Bonus Points.fcleared the screen of dots.
Players start with three PAC-MEN.*<=Screen cleared once.

An additional PAC-MAN is award- Screen cleared twice. ed for 10,000 points. Screen cleared 3 times. Screen cleared 4 times. 2? Screen cleared 5 times.

  • etc. —

Pi is available Pome

the flashing Power

PAC-MAN powers up, e, the Monsters start to run away.

58Y2"ig"24)
Points doubleJ149 cm49.5 cm6lcom

for

Monster.%29"32”22"
.740m81.25 cm56 cm
73"2612"34”

185.5 cm 67.25cm_ — 86.25 cm

C5ully|MIDWAY MFG. CO. 10601 W. Belmont Avenue Franklin Park, Illinois 60434 (312) 454-9200 Telex 72-1596 For Service information—call toll free 800-323-7182

Page 3

TABLE OF CONTENTS

Page No. INTRODUCTION ............--0- eee eee ots ney sean ye OES ye aS ee ga ee age 3 OPTION SWITCH SETTINGS 4 GENERAL TROUBLE SHOOTING 5 INTRODUCTION TO THE 280 7 TROUBLE SHOOTING LOGIC BOARD . SELF-TEST DISPLAY ...............--- ADDITIONAL TROUBLE SHOOTING .. POWER SUPPLY CONTROLINPUTS .. SYSTEM TIMING.... WATCHDOG CIRCUIT PROGRAM ROMS ...... Z80SYNC BUSCONTROLLER ...... SCRATCH PAD & V RAM ADDRESSER CHARACTER ROMS ATTACK RAMS COLOR PROM AUDIO CIRCUITRY FINAL AUDIO STAGES . AUXILIARY BOARD .... LOGIC BOARD DIAGRAM . SCHEMATICS ............- eee e ee ee eee renee IC FUNCTION LIST SERVICE BULLETINS

Page 4

NOTES

This space Is provided for personal notes

Page 5

INTRODUCTION

Midway’s new games, Pac-Man and Ms. Pac-Man, promises to be two of the

hottest new games on the market today. As with any high production product, there will

be a need for servicing from time to time. Therefore, since necessity is the mother of

invention, this manual is being written to satisfy that need and to simplify trouble-

shooting. So use this manual to its fullest potential, GOOD LUCK!

Page 6

PAC-MAN & MS. PAC-MAN

OPTION SWITCH SETTINGS Eee TITITTITITITIT ITT LAT TALL TAT ILL LLL] METHOD OF PLAY //T/II/TITTITTTI ITAA TATE TTT

SWé#1 SW#2 SW#3 SW#4 SWHS SWHE SWH7 SWHB

FREE PLAY ON ON

1 COIN1 PLAYOFFON
1 COIN2 PLAYSONOFF
2 COINS14 PLAYOFFOFF

ee ————————————————————————————EE—— TITTTTITIITTITITITIITTTITITTIT NUMBER OF MS. PAC-MENPERGAME //////////////(//////II////III1

1 MS. PAC-MAN 2 MS. PAC-MEN 3 MS. PAC-MEN 5 MS. PAC-MEN

TITTTITITTITTAT TTT IATALITTTTITIT ITLL TT BONUS MS. PAC-MEN //////////1101TTTHTLTTITTTII LITT ITLL

BONUS MS. PAC-MAN AT10,000 POINTSONON
BONUS MS. PAC-MAN AT15,000 POINTSOFFON
BONUS MS. PAC-MAN AT20,000 POINTSONOFF

NO BONUS OFF OFF

TTTTITITIATIFTIAITITTITITTTTTALITITTII LT SPECIAL FUNCTIONS F/T//TIITTITITTT TTI IATA TTA TTT TTL

AUTOMATIC RACK ADVANCE ON OFF FREEZE VIDEO (MONITOR PRESENTATION STOPS MOVING) OFF ON GAME OPERATES NORMALLY OFF OFF

Page 7

Harness Component Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player's coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). if the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely'in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. If the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the associated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.

Page 8

\f the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If not, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voltage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a significant drop in power. Cold solder joints in the game's harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. In any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. ff you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, meta! objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, control pane! buttons) does not operate at all, check the switch with a VOM or continuity tester to verify its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. tn many cases, the input will be +5 VDC. If so, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. If you find the signal at the PCB trace, the wire length or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 9

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.

CPU — central-processing unit. A computing system's “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and

Introduction to the

Z-80 CPU

The term “microcomputer” has been used to describe virtually every type of small computing device designed within the last few years. This term has been applied to everything from simple “microprogrammed” controllers constructed out of TTL MSI up to low end minicomputers with a portion of the CPU constructed out of TTL LSI “bit slices.” However, the major impact of the LSI technology within the last few years has been with MOS LSI. With this technology, it is possible to fabricate complete and very powerful computer systems with only a few MOS LSI components. The Zilog Z-80 family of components can be configured with any type of standard semiconductor memory to generate computer systems with an extremely wide range of capabilities. For example, as few as two LSI circuits and three standard TTL MSI packages can be combined to form a simple controller. With additional memory and I/O devices a computer can be constructed with capabilities that only a minicomputer could previously deliver. New products using the MOS LSI microcomputer are being developed at an extraordinary rate. The Zilog Z-80 component set has been designed to fit into this market through the following factors: development to get programs debugged, then replaced by ROM for mass production. ROM — read-only memory. The program, or binary on-off bit pattern, is Set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor’s basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LS! — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

  • ‘The Z-80 is fully software compatible with the popular 8080A CPU.
  • Existing designs can be easily converted to include the Z-80.
  • The Z-80 component set is at present superior in both software and hardware capabilities to any other microcomputer system on the market today.
  • For increased throughput the Z80A operating ata 4 MHZ clock rate offers the user significant speed advantages. Microcomputer systems are extremely simple to construct using Z-80 components. Any such system consists of three parts:
  • CPU (Central Processing Unit)
  • Memory
  • Interface Circuits to peripheral devices The CPU is the heart of the system. Its function is to obtain instructions from the memory and perform the desired operations. The memory is used to contain instructions and in most cases data that is to be processed. For example, a typical instruction sequence may be to read data from a specific peripheral device, store it in a location in memory, check the parity and write it out to another peripheral device. Note that the Zilog component set includes the CPU and various general purpose I/O device controllers, while a wide range of memory devices may be used from any source. Thus, all required components can be connected together in a very simple manner with virtually no other external logic.
Page 10

General Purpose Registers There are two matched sets of general purpose registers, each set containing six 8-bit registers that may be used individually as 8-bit registers or as 16bit register pairs by the programmer. One set is called BC, DE and HL while the complementary set is called BC’, DE’ and HL’. At any one time the programmer can select either set of registers to work with through a single exchange command for the entire set. In systems where fast interrupt response is required, one set of general purpose registers and an accumulator/flag register may be reserved for handling this very fast routine. Only a simple exchange command need be executed to go between the routines. This greatly reduces interrupt service time by eliminating the requirement for saving and retrieving register contents in the external stack during interrupt or subroutine processing. These general purpose registers are used for a wide range of applications by the programmer. They also simplify programming, especially in ROM based systems where little external read/write memory is available. Arithmetic & Logic Unit (ALU) The 8-bit arithmetic and logical instructions of the CPU are executed in the ALU. Internally the ALU communicates with the registers and the external

a

MREQ SYSTEM _/ ionG CONTROLS RD wa

FSH

WALT

CPU WAIT CONTROL int ii

RESET

CPU ‘BUSRQ BUS SUSAR contro: \°"**

o +5V

Z-80 PIN CONFIGURATION data bus on the internal data bus. The type of functions performed by the ALU include: Add Left or right shifts or rotates (arithmetic. and logical)

Subtract Increment

Logical AND Decrement Logical OR Set bit Logical Exlusive OR Reset bit Compare Test bit Instruction Register and CPU Control As each instruction is fetched from memory, it is placed in the instruction register and decoded. The control sections performs this function and then generates and supplies all of the control signals necessary to read or write data from or to the registers, control the ALU and provide all required external control signals.

Z-80 CPU Pin Description The Z-80 CPU is packaged in an industry standard 40 pin Dual In-Line Package. The I/O pins are shown in the below figure and the function of each is described.

ADDRESS BUS

DATA BUS PPESPPSS

Page 11

Ao-Ais (Address Bus) Tri-state output, active high. Ap-A;s constitute a 16bit address bus. The address bus provides the address for memory (up to 64K bytes) data exchanges and for I/O device data exchanges. I/O addressing uses the 8 lower address bits to allow the user to directly select up to 256 input or 256 output ports. Ag is the least significant address bit. During refresh time, the lower 7 bits contain a valid refresh address.

Do-D; (Data Bus) Tri-state input/output, active high. Do-D, constitute an 8-bit bidirectional data bus. The data bus is used for data exchanges with memory and I/O devices.

M, (Machine Cycle one) ___ Output, active low. M; indicates that the current machine cycle is the OP code fetch cycle of an instruction execution. Note that during execution of 2-byte op-codes, M1 is generated as each op code byte is fetched. These two byte op-cc codes always begin with CBH, DDH, EDH or FDH. Mi also occurs with IORQ to indicate an interrupt acknowledge cycle. MREQ (Memory Request) Tri-state output, active low. The memory request signal indicates that the address bus holds a valid address for a memory read or memory write operation. 1ORQ (Input/Output Request) Tri-state output, active low. The iORQ signal indicates that the lower half of the address bus holds a valid I/O address for a1/O read or write operation. An IORQ signal is also generated with an M1 signal when an interrupt is being acknowledged to indicate that an interrupt response vector can be placed on the data bus. Interrupt Acknowledge operations occur during M, time while I/O operations never occur during M, time. RD (Memory Read) Tri-state output, active low. RD indicates that the CPU wants to read. data from memory or an I/O device. The addressed 1/O device or memory should use this signal to gate data onto the CPU data bus. WR (Memory Write) Tri-state output, active low. WR indicates that the CPU data bus holds valid data to be stored in the addressed memory or I/O device. RFSH (Refresh) Output, active low. RFSH indicates that the lower 7 bits of the address bus contain a refresh address for dynamic memories and the current MREQ signal should be used to do a refresh read to all dynamic memories.

HALT (Halt state) Output, active low. HALT indicates that the CPU has executed a HALT software instruction and is awaiting either a non maskable or a maskable interrupt (with the mask enabled) before operation can resume. While halted, the CPU executes NOP’s to maintain memory refresh activity.

WAIT (Wait) Input, active low. WATT indicates to the Z-80 CPU that the addressed memory or I/O devices are not ready for a data transfer. The CPU continues to enter wait states for as long as this signal is active. This signal allows memory or I/O devices of any speed to be synchronized to the CPU.

INT (Interrupt Request) Input, active low. The Interrupt Request signal is generated by 1/O devices. A request will be honored at the end of the current instruction if the internal software controlled interrupt enable flip-flop (FF) is enabled and if the BUSRQ signal is not active. When the CPU accepts the interrupt, an acknowledge signal (IORQ during M, time) is sent out at the beginning of the next instruction cycle. The CPU can respond to an interrupt in three different modes that are described in detail in section 5.4 (CPU Control Instructions).

NMI (Non-Maskable Interrupt) Input, negative edge triggered. The non maskable interrupt request line has a higher priority than INT and is always recognized at the end of the current instruction, independent of the status of the interrupt enable flip-flop. NMI automatically forces the Z-80 CPU to restart to location 0066. The program counter is automatically saved in the external stack so that the user can return to the program that was interrupted. Note that continuous WAIT cycles can prevent_the cu the current instruction fre from ending, and that a BUSRQ will override a NMI.

RESET Input, active low. RESET forces the program counter to zero and initializes the CPU. The CPU initialization includes:

  • Disable the interrupt enable flip-flop
Page 12
  • Set Register | = 00x
  • Set Register R =00H
  • Set Interrupt Mode 0 During reset time, the address bus and data bus go to a high impedance state and alt control ouput signals go to the inactive state.

BUSRQ (Bus Request) Input, active low. The bus request signal is used to request the CPU address bus. data bus and iri-state output control signals to go to a high impedance state so that other Gevices can control these buses When BUSRQ is activated, the CPU will set these buses to a high impedance state as soon as the current CPU machine cycle is terminated.

BUSAK (Bus Acknowledge) Output, active low. Bus acknowledge is used to indicate to the requesting device that the CPU address bus, data bus and tri-state control bus signals have been set to their high impedance state and the external device can now control these signals.

CLK (Clock) Single phase TTL level clock which requires only a 330 ohm pull-up resistor to +5 volts to meet all clock requirements. nee a

Page 13

PAC - MAN

TROUBLE SHOOTING PC A082-91375-A000

NOTE: AIl!.C. trouble shooting information is with the |.C. removed from circuit.
POSITIONCHIPPOSSIBLE TROUBLE
1-E74LS161All Characters are at top of screen - Characters move

horizontally only.

1-F74LS283Lines and Squares entire screen - Effects Self Test.
1-H74LS283Horizontal lines across screen in color.
1-K74LS283No Sounds - Game plays normal.
4-L74LS174-Same as 1-K
1-M5623 (Prom)Same as 1-K
1-NCD 4066Same as 1-K
2A93415 (Ram)Effects Color of all Characters - Game plays.
2-B93415 (Ram)Same as 2-A
2-C93415 (Ram)Same as 2-A
2-D93415 (Ram)Effects Color of the Characters - Eyes only two

Characters.

2-E74LS161Characterstopofscreen-Charactersmove

horizontally- Effects Game Play-Color & Sound OK.

2-F74LS283Effects Self Test - Row of Characters horizontally

across screen. Effects Game Play - Color & Sound OK.

2-H74LS86All Characters are Squares - Effects Self Test -

Horizontal Color Bars across screen.

2K74LS89Effects all Sounds - Game plays & color OK.
2-L74LS89Same as 2-K
2-M74LS273Same as 2-K
2-774LS02_Effects Sync - No Video - No Sound - Moving

Diagonal Lines.

2R74LS161Vertical short lines in color - Effects Game Play.
2-S74LS161Horizontal Color Bars across screen - Effects Game

Play.

Page 14

POSITION

3A

3-B

3D

3-E

3-F

3-H

3-L

3M

3-N

3-P

3-R

4A

4-B

4-C

4-D

4-F

4-H

4-K

aL

4-M

4-N

4P CHIP

74LS158

74LS157

74LS75

74LS20

74LS89

74LS89

74LS158

74LS157

1M5623

74LS74

74LS10

74LS161

74LS161

1M5623 (Prom)

74LS377

74LS00

74LS273

74LS157

74LS86

74LS245

2114 (Ram)

2114 (Ram)

2114 (Ram)

2114 (Ram)

2114 (Ram) POSSIBLE TROUBLE

No Characters in maze.

No Video (Dead)

Characters missing in maze - Game plays without seeing Characters.

No Video (Dead)

Same as 3-D

All Characters move jerking - Characters do not stay in maze.

No Sounds - Game Plays.

Same as 3-K

Same as 3-K

Effects Sync - Color Diagonal Lines.

No Video (Dead)

No Video (Dead)

Effects Sync - Diagonal Lines.

No Video (Dead)

Distorted Letters - No Color - Maze is White - Effects Game Play.

No Video (Dead)

No Maze - Screen covered with Number Fives - No Letters - Characters moving about.

Distorted Maze - Letters Upside Down - Characters Distorted.

Distorted Characters - Letters and Sound.

Flashing White Dots - No Color.

All White Zeros on screen.

Flashing Numbers and Letters in Color.

Blank screen with a Single Zero at top of screen - Two Red Characters Only.

Same as 4-K

Flashing Self Test - Flashes continuous.

Page 15

POSITION

4-R

5-A

5-B

5-C

5-E

5-L

5-M

5-N

5-S

6-B

6-D

6-E

6-H

6-J

6-R

6-S

7-F

7-H

7-5

7-K

7-M

7-N CHIP 2114 (Ram)

74LS157

74LS194

748194

9332 (Prom)

9332 (Prom)

74LS139

74LS74

74LS08

NVC 284 (Custom)

Z80 CPU

NVC 285 (Custom)

9332-B (Prom)

9332-B (Prom)

9332-B (Prom)

9332-B (Prom)

74LS367

74LS367

7603

74LS08

74LS138

74LS138

74LS02

74LS139

74LS42 POSSIBLE TROUBLE Screen is blank with a Number One flashing - A single Character can be seen.

Blue Screen - All Characters are Squares - No Letters or Numbers.

Color Squares around each Character - All maze dots are blue.

Effects Maze - Characters have Squares around them - Self Test in Red.

Blue screen with Horizontal Squares - No Maze - No Letters or Numbers random Characters.

Effects Characters in Maze which are Squares - Everything else normal.

Red screen flashing with all Letter F’s.

Screen covered with Garbage in Color.

Effects Sync - Moving Diagonal Lines in Color.

Flashing White Dots - Game plays.

Screen covered with Garbage in Color.

Same as 6-B

Flashing blue Zeros and Garbage - Continuous Meter Pulses.

Blank screen with a Flashing Number One - Bad Rom One.

Screen covered with Garbage.

Blank screen with random Characters.

Screen flashing with Garbage in Color.

Same as 6-R

No Video (Dead)

Eleven Horizontal rows of Zeros across scre2n.

No Video (Dead)

No Video (Dead)

Same as 7-J

Screen covered with Garbage in Color.

Same as 7-J

Page 16

POSITION

8-A

8-B

8-C

8-D

8-E

8-F

8-H

8-K

9-C

11-A CHIP

74LS107

74LS368

74LS74

74L$367

74LS367

74LS367

74LS367

74LS259

74LS161

M377 — LM1877

ADDITIONAL DEVICES

10-A

B-7

P-8 (IR1)

R-9

L-9

C-9 Dip Switch

Crystal (18.432)

78GVIC (Regulator)

D44VM4

D40K1

2N3391 POSSIBLE TROUBLE

No Video (Dead)

Same as 8-A

Effects Sync - Diagonal Lines flashing.

Effects Dip Switch settings.

No Coin - No Up & Down Controls - 1st Player.

No Controls - 2nd Player.

No Test Switch - 1 & 2 Player Select.

Stays in Self Test - Shows Memory OK.

Screen covered with Garbage in Color.

No Sounds.

Effects Coin Play - Number of Pac-Man Bonus Pac-Man.

No Video (Dead)

Effects +5 VDC

Pass Transistor - Effects +5 VDC

Transistor - Effects Coin Counter

Transistor - Effects Power Reset

Page 17

SELF-TEST DISPLAY AND BOARD LOCATION COORDINATES

MEMORY OK or (M-Rom-1 / Bad C Ram-0 / Bad W Ram-1 / etc.)

*1 COIN "1 CREDIT BONUS *15000 MS. PAC-MAN *3 UPRIGHT or (TABLE)

  • = switch selectable

If abad ROM or Ram chip is found by the games internal check system during the Self-Test, the game indicates this to you by showing the location code of the bad chip(s) in place of the “‘MEMORY OK”’ message. The foilowing table translates the chip location codes into actual positions on the game logic P.C. Board.

DISPLAY DESCRIPTION

MEMORY OK All RAMs are good. BAD V RAM-0 RAM located on Logic PC board at position 4K is bad. BAD V RAM-1 RAM located on Logic PC board at position 4N is bad. BAD C RAM-0 RAM located on Logic PC board at position 4L is bad. BAD C RAM-1 RAM located on Logic PC board at position 4P is bad. BAD W RAM-O RAM located on Logic PC board at position 4M is bad. BAD W RAN-1 RAM located on Logic PC board at position 4R is bad.

MEMORY OK All ROMs are good. M-ROM-O ROM located on Logic PC board at position 6E is bad. M-ROM-1 ROM located on Logic PC board at position 6F is bad. M-ROM-2 ROM located on Logic PC board at position 6H is bad. M-ROM-3 ROM located on Logic PC board at position 6J is bad.

The detection of bad components on the Auxiliary Logic PC Board is not quite as simple as is the case for the Main Logic PC Board. The following table lists the components that are on this Auxiliary PC Board and what symptoms they will cause to appear on the monitor when each is bad.

---BAD COMPONENT/SYMPTON TABLE---

BAD COMPONENT | SYMPTOM DISPLAYED ON MONITOR (GAME IS NOT IN SELF-TEST)

2-80 CPU

E-ROM-1

ROM located on Auxiliary PC board at position U7

Page 18

-~-BAD COMPONENT/SYMPTON TABLE CONTINUED—

BAD COMPONENT SYMPTOM DISPLAYED ON MONITOR (GAME IS NOT IN SELF-TEST)

CUSTOM CHIP CG-820

CUSTOM CHIP CG-821

CUSTOM CHIP CG-822

CUSTOM CHIP CG-823

Screen display is sam

CG-823 located on A: rOG-621__-_ PC board at position U3

To check your game function switches and buttons (coin counter switches, TEST CREDIT button, 1 PLAYER and 2 PLAYER buttons): active each one while the game is in the Self-Test mode. You should hear a game sound for each activation. If you do not hear it, the switch/button is either not working, miswired, or disconnected. Check it out thoroughly.

When finished with the Self-Test mode, slide the Self-Test switch back to the ‘‘OFF’’ position.

  • Across hatch pattern appears on the monitor screen for about 1 to 2 seconds.
  • If you wish to keep this test pattern on the monitor screen for further use, slide Self-Test switch to the ‘‘ON’’ position after the cross hatch pattern appears and before it disappears.
  • When finished with the cross hatch pattern, set the Self-Test switch to the “‘OFF’’ position.
  • Normal game functions will now return to the monitor screen.

OPTION SWITCH SETTINGS:

To change the option switch settings, you DO NOT have to take the Main Game Logic Board out of the game. They can be easily reached through the rear access door on the Upright and Mini models. On the Cocktail Table model, you do have to open the table top to reach them.

When changing any options, ALWAYS put the game into the Self-Test mode, make your changes, check the results on the monitor screen, take the game out of the Self-Test mode, and play the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be, (These switches are small and this can happen.)

The option switch settings and what they will make the game do, are shown in the following Figure.

Page 19

10.

11.

12.

13.

14, PAC-MAN

TROUBLE SHOOTING LOGIC BOARD PC A082-91375-A000

. CHECK +5VDC AT CPU AND ROMS.

. RESET LINE PIN #26 OF CPU NORMALLY HIGH AND GOES LOW WITH RESET.

. BMHZ CLOCK FREQUENCY AT PIN #13 OF 8-B AND 3MHZ AT PIN #6 OF CPU.

. CHECK ROM TEST FOR A MEMORY FAILURE.

. CHECK ALL ADDRESS AND DATA LINES AT CPU.

. CHECK ALL ADDRESS AND DATA LINES AT 4-A AND 7-F COLOR PROMS.

. CHECK ALL ADDRESS AND DATA LINES AT 5-E AND 5-F CHARACTER ROMS.

. WHEN CHARACTER ROM 5-E IS REMOVED GAME PLAYS BUT MAZE IS MISSING.

. WHEN CHARACTER ROM 5-F IS REMOVED GAME PLAYS BUT PAC - MAN AND GHOST MONSTERS ARE BLOCKS OF COLOR.

WHEN ALL PROGRAM ROMS ARE REMOVED THE SCREEN WILL BE ROWS OF BLUE DIAGONAL LINES.

CHECK SOUNDS AND SWITCHES USING TEST SWITCH.

SWITCHES #7 AND #8 MUST BE OFF FOR NORMAL GAME PLAY.

SWITCH #7 ON WILL TEST RACKS.

GOOD LUCK!

Page 20

NOTES

This space Is provided for personal notes

Page 21

POWER SUPPLY SECTION

The 12VAC and 12VCT lines are rectified to DC voltage by diodes D3 and D4.

The Waveform Drawings may help to explain how this is done.

AC voltage is constantly alternating polarity. At one moment the 12VAC line at

pin W is positive and the 12VAC line at pin X is negative when measured from 12VCT.

The next moment pin X becomes positive and pin W negative. Between the *(asterick)

marks on Waveform Drawing Number 1 is one complete cycle. During the (A) half of the

cycle, pin W is positive in respect to the 12VCT line so current flows from 12VCT through

the 78GUIC regulator and then back through D3 to the transformer. During the (B) half

of the cycle, pin X is positive and current flows from 12VCT through the regulator, then

through D4 back to the transformer.

Now we have DC voltage but as seen in Waveform Drawing Number 2 it is very

wavy. This is called ripple. Excessive ripple may show up as a hum in the speaker, a

wavy picture or the game may not operate at all.

This is where capacitors C29 and C5 are used to filter out the ripple. Since a

capacitor can store an electron charge for a short period of time, we connect these

capacitors from center-tap or logic ground to the positive DC voltage line. See Waveform

Drawing Number 3. At point (A) the capacitors are charged. As the DC voltage tries to

drop to point (B) the capacitors discharge and hold the line high. This is repeated for

every cycle and the end result is nearly a straight line of DC voltage. As the drawing

shows, the line is not perfectly straight because some ripple remains. As long as the

ripple is less than .2 volts, the game should operate normally.

The reason for using a tantalum capacitor at C5 is because electrolytic capaci-

tors act like inductors at high frequencies. Tantalum capacitors have a fairly constant

reactance over the frequency spectrum and are better for filtering out noise or radio

frequencies that may enter the line.

After the 12 VAC has been converted to DC voltage and filtered by C29 and C5,

Page 22

the end result is approximately 16VDC at pin number 3 of the 78GUIC regulator. This

46VDC is also used to power the audio amplifier at location 11A. If this circuit is

operating properly, pin number 2 of the regulator will read +6VDC.

The 7VAC and 7VCT lines are converted to DC voltage by diodes D7 and D8

and filtered by capacitors C7 and C8 to end with +7.5VDC at pin E of the connector.

This +7.5VDC is then fed to the collector pin of the D44VM4 pass transistor. A TIP31

transistor may be used as a substitute.

The +6VDC from pin number 2 of the regulator is fed to the base pin of the

pass transistor to turn it on. If the circuit is working properly, the emitter pin of the

transistor will present +5VDC to the rest of the logic board. You will see that although

the 78GUIC regulates the + 5VDC, the pass transistor supplies the current.

Zener diode D9 protects the logic circuitry. If for any reason the emitter of the

pass transistor exceeds +5VDC, D9 will shunt the line to ground. This is an important

feature because TTL logic circuitry can be damaged by voltages over +5.25VDC.

Occasionally a component in the logic circuitry will be defective in such a way

that it pulls the +5VDC down to +3VDC or lower, even though the power supply circuit

is functioning properly. The faulty logic component will usually be very hot, but not

always. To isolate the +5VDC from the logic circuitry, remove the jumper wire next to

R52 near the black heat sink.

Page 23

POWER SUPPLY CIRCUITS

“St

c7,8 10000ut 10V ELECT.

1N914B

= —T~ce2 470uf = 10V ELECT

25V ELECT.

Page 24

THIS OWG.IS CONFIDENTIAL & PROPERTYOFMIDWAYMFG.coO. [ [| Cid DIM. TOLERANCES TiS! Pp UNLESS OTHERWISE SPEC —_ MIDWAY MFG. CO. es CONCENTRICITY T.LR. .. .002 WONE FRANKLIN PK.,IL.60131 A BALLY CO. FRACTIONAL .... DECIMAL . k WA VE FORM PART NO. ; DRAWING: oo

Page 25

CONTROL INPUT CIRCUITS

Troubleshooting the control input circuits on the logic board is easy since all

controls (coins, left, up, start, etc.) are handied the same way. For example, take the

“move left’”’ input. The left movement switch on the joy stick is normally open with one

terminal connected to common or logic ground. The other terminal is connected to pin M

on the logic board edge connector.

If the circuit is working properly, pin M will measure +5 volts and will drop to

0 volts when the left movement switch is closed. If pin M remains at +5 volts when the

Jeti rnovernent switch is closed, the problem is either the switch or a loose connection

because the signal is not reaching the logic board. If pin M measures correctly but the

PAC-MAN won't move left or if pin M is stuck low (0 volts) the problem is on the logic

board.

Once we are sure that the logic board is at fault, it may be easier to work

backwards.

{f resistor R47 was broken or burnt the signal at pin M would not reach pin number 4 of the buffer at location 8E, so you may prefer to start at the buffer. There are two components in this circuit that might hold the signal low. Capacitor C22 could be

shorted allowing ground to pass through to the line or the buffer could be bad. It is easier

to remove C22 first, then if the problem remains, change the buffer.

The RRC network comprised of RM8, R47 and C22 conditions the signal. RM8

pulls the line up so that it reads +5 volts when the move left switch is open. R47 limits

the current into the circuit. C22 debounces the signal.

When a mechanical switch is first closed, it bounces a few times before coming

to rest in the closed position. In movement circuits this may not matter but for coin

circuits to yield half a dozen bounces for one quarter could cause a problem.

Page 26

ire

BOUNCING

THIS DWG. IS CONFIDENTIAL & PROPERTY OF MIDWAY MFG. CO. +} |. TOLERANCES UNLESS OTHERWISE SPEC. MIDWAY MFG. CO. | CONCENTRICITY TLR... .002 P4-16/82 Pwone _| FRANKLIN PK., IL. 60131 ABALLYCO. FRACTIONAL .. ok. Peer WAVE FORM Me oraaows || DRAWING

Page 27

To eliminate this bouncing we use a capacitor connected between the line and

ground. See Waveform Drawing Number 4. The waveform drawing shows two signals.

(A) is the switch bouncing. (B) is the capacitor discharging. When the move left switch is

closed, the capacitor discharges. You will see the value of the capacitor is chosen so that

it finishes discharging after the bouncing has stopped. The circuit will see only a single

smooth pulse.

Pin R on the logic board edge connector is only used in table models. When it is

connected to ground it causes the image on the screen to flip for the second player. Also

movement controls on pins V, 13, P and 12 are only used in table models. Although the

schematic shows two circuits for COIN only pin J is used because the coin switches are

connected in parallel.

Besides a bad capacitor or buffer causing loss of a control, resistor packs RM7 and RMB can cause unusual problems. Each pack contains 8 resistors and it is possible that two resistors in a pack will ‘‘cross talk’’.

In one example, the game would add a free credit every time the joystick was moved to the right. It turned out that when pin 11 of the edge connector was low, the pull up resistor in RM8 would cross-talk or leak to the pull up resistor for the COIN 1 circuit. This would force pin number 12 of the buffer 8E low and the game would add accredit.

In another example, pressing the player 1 button would throw the game into

test, so RM7 was changed.

Studying the option switches at location 9D, you will find that switches 1 thru 7

are handled like control inputs. The current limit resistors and debounce capacitors are

absent because the switches will not see continuous duty and bouncing only occurs after

a switch is first closed.

Page 28

Dip switches 1 and 2 are for price setting, 5 and 6 for setting the number of

points required to earn the bonus PAC-MEN and switches 3 and 4 determine the

number of PAC-MEN that starts the game.

The two sets of pads can be shorted with wire and soldered to connect pins 10

and 14 of buffer 8D low. When the halves of pad A are shorted, the character nicknames become AAAA, BBBB, CCCC and DDDD. When pad B is shorted, the game becomes slightly more difficult to play. There are other sets of pads on the board but only pad B is useful.

Switches 7 and 8 are used as diagnostic aids. When switch 8 is closed (or on)

the game will freeze the action. The image on the screen will freeze and even a note in

the middle of a tune will be held. This freeze option has proved valuable in

troubleshooting the video circuits.

When switch 7 is on, the game will exhibit a rack test. First, the starting maze and cherries will appear. The cherries will shift to the bottom right corner of the screen.

Then the second maze and the strawberry will appear. Within seconds the strawberry

will shift to the bottom of the screen. Third, the intermission cartoon will break the

tension. Then on to the 4th, Sth, 6th, etc. mazes and cartoons until 7 keys appear on

screen. Anytime during this rack test one can turn switch 7 off and begin game play at

that moment and maze.

Often a symptom occurs only after a certain maze. For instance, maybe after

the 5th maze dots appear around the apple. even if one were skilled enough to play to the

apple, one would have only seconds left to diagnose the circuit before being eaten, “with a Joystick In one hand and a logic probe in the other’’.

Page 29

Instead, one can simply rack test to the 5th maze, then turn switch 7 off. Game

play would start immediately. As the symptom (dots around apple ) appears, turn switch

8 on and the image will freeze.

CONTROL INPUT CIRCUITS

ras, 1 BOR IKxg, SP KS SSSSSSSMSSSSASASSSASSSSS LiL Po | 759367

od ! cry bc}

staat 2 [_ }4,—;tt_-st Daa) | com 2 [4ae22>
|saz ealS77, oo|meecedOSS
staat oF>Nicon
vestDJ_—Sap}et pts ome! | cows (7)—f
aht=NGI
COCKTALL 2ND PLAYER AMT=oNSf
seesCEae | er CET
vw$Cpt gefaa teoatfue|

vent, 3e mo tl “Lom J

Page 30

NOTES

This space is provided for personal notes

Page 31

SYSTEM TIMING

System timing and clocking for the Z80 CPU starts with the crystal oscillator

circuit. An 18.432 MHz (megahertz or millions of cycles per second) crystal at location

7B is used to set the oscillator frequency. The crystal is a slice of quartz which has been

cut to precise dimensions so that it tends to oscillate at a certain frequency. Guitar and

piano strings are designed with specific dimensions which depend on what frequency or

note they are to generate. So is a tuning fork and xylophone. Two 330 ohm resistors, a

100pf. capacitor and three inverting buffers at 8B complete the oscillator circuit. The signal from the oscillator circuit is used to clock the flip-flops at location

8A. Output pine 3 and 6 of 8A are inverted by two more buffers in 8B to yield the 6 MHz and 6M* signals. The inverse of the 6M* signal (6M*) is available at pin number 11 of

the XOR gate in location 4F. 6 MHz is connected to pin 3 of a flip-flop at 8C and also to the clock inputs of

binary counters 3R and 38. 8C divides the 6 MHz in half and outputs a 3 MHz signal

from pin number 5. This 3 MHz is referred to as the 1H signal. The 1H signal is inverted

by the last buffer in chip 8B and then used to clock pin 6 of the Z80 CPU.

The binary counter at 3R counts the 6 MHz signal and divides it in half four

times. This way the 2H signal is half the frequency of 1H, 4H is half the frequency of 2H, 8H is half the frequency of 4H...etc. The 1H through 256H (horizontal timing) signals are used to generate the HSYNC, HBLANK and HBLANK signals. Flip-flop 5M halves

the frequency of HSYNC to provide the 1V signal and counters 2R and 2S provide av through 128V. VSYNC (vertical sync) from pin 11 of counter 2S is used to produce the CMPSYNG. (composite sync) signal for the monitor. Usually the game will not be operative if any of the H or V signals are missing. Without the signal from pin 7 of 8B in the crystal oscillator circuit the game will be

completely dead (no video, no sound and no pulsing or activity anywhere on the logic

board).

Page 32

An easy way to check the H and V signals is to use a video probe on the outputs (pins 11, 12, 13 and 14) of counters 2R, 2S, 3R and 3S. A video probe is simply a wire

with a 470 ohm resistor connected to one end. By connecting the wire to either the red,

green or blue color outputs to the monitor any signal probed by the resistor end will

cause a change in color or pattern on the monitor screen. Assemble a video probe to

check the H and V signals.

When using a video probe on the 256H signal the monitor screen will turn light

blue. The maze and characters will still be visible but it will appear as if a blue filter were

placed over the screen. The 128H signal will split the screen in half horizontally so that

one half is light blue while the other half is normal. 64H will cause two blue bars on the

screen. 32H will cause four bars. Each H signal after 32H will double the number of bars on the screen. Using the video probe on the V signals will cause vertical bars. The video probe can also be used as a logic probe. When the resistor end is

connected to a high signal the monitor screen will turn light blue (red or green can be

used also). When it is probing a low signal the screen will be normal. This can be useful

in troubleshooting the control input circuits.

Page 33

SYSTEM TIMING CIRCUITS

Page 34

NOTES

This space is provided for personal notes

Page 35

THE WATCHDOG CIRCUIT

The ‘‘watchdog”’ circuit was designed to reset the microprocessor if it detects

an error in system timing or on the address and data buses. In older games without watchdog circuits static discharge, noise or vibration would introduce false information into the system which sometimes caused the game to lock-up until it was manually reset.

In later games the watchdog will detect the false information or lock-up condition and

will deliver an automatic reset pulse to the microprocessor. This automatic reset pulse

will normally occur within seconds after the error has been detected, thereby minimizing

the games down time. The 74LS161 binary counter at location 9C will be cleared before it counts to 15.

This way the signal on pin 15 remains low and the signal on pin 13 of NOR gate 7L

remains high. Pin 26 of the Z80A microprocessor must be high for the system to operate.

If an error is detected in the system, 9C will not be cleared before reaching the critical count of 15. This will cause a high going pulse on pin 15. NOR gate 7L will invert the high going pulse and deliver a low going pulse to pin 26 of the microprocessor to

reset the system. Occasionally there will be a problem in the system timing or 9C will be faulty

and the game will continually reset. Every second or two the game will run through the

power up or self-test sequence and the signal on pin 26 of the microprocessor will be

pulsing. To determine if the problem is caused by a faulty watchdog circuit, try the

self-test. If the resetting stops and the test reads ‘‘Memory OK’’ the problem is

probably the watchdog. \f the VBLANK signal is incorrect the watchdog will “‘bark’’ (pulse on pin 15 of

9C). Since the VBLANK signal is derived from the 16V through 128V signals, if it is

incorrect, one may have to trace back to counters 2R, 2S, 3R and 3S to find the fault.

If the decoder at location 7J is faulty, the WDR (watchdog reset) signal on pin

42 will not clear counter 9C in time and the watchdog will bark. Also if the signals into 7J

are incorrect the WDR signal will fail to clear 9C. It is through 7J that the watchdog

detects an error on the address bus.

To determine if counter 9C is causing the problem, cut pin 2. The game should

Page 36

then operate normally. If the game does not operate normally after cutting pin 2 of 9C

the problem is elsewhere in the system.

Remember the tilt switch on the coin door and the red switch next to location

11A are also in the reset circuit and may cause problems similiar to a faulty watchdog.

q rasoz

Y

WATCHDOG CIRCUIT

Page 37

THE PROGRAM ROMS

The personality (software or program) of the game is stored in the program

ROMS. Each ROM holds 4,096 words (8 bits per word) of the program. The schematic

shows eight ROMS but only locations 6E, 6F, 6H and 6J are used. Either a ROM or an

EPROM (erasable and programable ROM) can be used at these four locations.

Each ROM may be called upon hundreds or thousands of times a second to read out its programming to the data bus. When the CE (chip enable) input on pin 20 is low

the ROM is enabled. When the ROM is enabled the 8 bit word at the location called for

by the address bus will appear on the ROM outputs. The schematic shows pin 18 as a CE

input but on the types of ROMS and EPROMS being used pin 18 is address A11.

The address and data buses are paralleled to the ROMS. Because these ROMS

are tri-state components they can share the eight data lines. If they were not tri-state

components four ROMS (with eight data outputs each) would require 32 data lines.

When a tri-state component is in the tri-state mode its outputs are disabled and

will not drive a line high or low. When a component is in the tri-state mode its outputs

respond as if it were completely removed from the circuit. With this tri-state feature

many components can share the same output lines and as long as only one component is

enabled at any time that component will control the lines. If two or more components are

enabled at the same time the lines they share will not be driven properly and the

components may be damaged. For example, if two program ROMS are enabled at the same time one might try to drive the DO line low while the other tries to drive the Do line

high. The outcome would be a faulty DO line. This tri-state feature is used elsewhere on

the logic board. See the logic board schematic. The control input buffers at 8D, 8E, 8F

and 8H are tri-state components. When pins number 1 and 15 are low data on the buffer

inputs will appear on the outputs. When pins 1 and 15 are high the buffer outputs are

disabled. This allows the four buffers to share the eight DB (buffered data) lines. The component at 5S and the buffers at 6R and 6S are also tri-state devices.

Page 38

The component at location 7N is used to control the tri-state mode of the ~

program ROMS. 7N is a 74LS42 BCD to decimal decoder. BCD means binary coded

decimal. With the decimal system we count 0, 1, 2, 3, 4, 5...ete. Because the binary

system in digital electronics only uses the symbols 1 and 0 we must use a code to indicate

all other numbers. In binary the number 5 is written 0101. The first bit on the right

represents a 1. The next bit represents a 2. The third bit represents a 4 and each bit to

the left represents twice the number of the preceeding bit. The fourth bit from the right

represents an 8. In the word 0101 the first bit is a 1 (or high) so we have a 1. The second

bit is 0 (or low) so we do not have a 2. The third bit from the right is high so we do have a

4 and the last bit is low so we do not have an 8. Now add the numbers we do have. The

first bit represents a 1 and the third bit represents a 4. 4 plus 1 equals 5. With the binary

system we count 0000, 0001, 0010, 0011, 0100, 0101. . .etc. The BCD to decimal decoder at 7N has ten outputs representing 0 through 9 in

decimal. Pins number 12, 13, 14 and 15 are inputs for a 4 bit binary number. Pin 15 is the

A input (or least significant bit) and represents a 1. Pin 12 is the D input (or most significant bit) and represents an 8. All ten decimal outputs are normally high. When a binary number is written into the inputs 7N decodes the 4 bits into decimal and the corresponding pin for that decimal number goes low. For example, if the binary number

0011 is on the inputs of 7N the output pin number 4 will go low because it represents the

decimal number 3. When pin 4 goes low the program ROM at 6J will be enabled.

Because only one output on 7N can be low at any time pins 1, 2 and 3 will be high and

ROMS 6E, 6F and 6H will be in the tri-state mode. If the binary number 0001 was on the

inputs pin 2 would go low because it represents the decimal number 1 and ROM 6F

would be enabled while 6E, 6H and 6J would be in tri-state.

Wecan see that this circuit allows four tristate ROMS to share the data bus and

that chip 7N controls the tri-state mode of the program ROMS.

Page 39

PROGRAM ROMS

Page 40

THE Z80 SYNC BUS CONTROLLER

The component at location 6D will be either an NVC285 custom integrated

circuit or a small printed circuit board with TTL chips. This is the Z80 SYNC bus

controller. its purpose is to control the passage of data between the CPU data bus and

the DB (buffered data) bus. Information can pass through component 6D from the CPU

data bus to the DB bus or from the DB bus to the CPU. When a component can pass data

in either direction it is called bidirectional. To see how this is accomplished look at the

Z80 SYNC BUS CONTROLLER schematic. The numbers in square boxes represent the

pins on the small printed circuit board or on the NVC285.

The eight CPU data lines on pins 18 through 25 are fed to the inputs of the

tri-state buffers at location U5. The R/W (read/write) signal at pins 1 and 19 of US

controls the buffer outputs. When the R/W signal is low data will pass from the CPU

data bus to the DB bus. When the R/W signal is high the buffer outputs are disabled and

pins 4 through 11 can be used as inputs from the DB bus. When the CPU requires data

from the DB bus the WREQ (write request) signal goes low to enable the latches at

location U6. When U6 is enabled and signals on the D inputs will pass to its Q outputs

and the CPU data bus at pins 18 through 25. The direction that data passes through the

280 SYNC BUS CONTROLLER depends on which component, U5 or U6, is enabled. The

latches at U7 are used to store an 8 bit word from the CPU date bus or the DB bus until

that word is needed on either bus.

Note that the R/W signal is derived from the component at 6D and the CK

signal leaving pin 12 of 6D is gated through chip 7L to control the tri-state component at

4H in the ‘‘scratchpad circuit’’.

Page 41

[= 28 om connecron > ePuLL UP

MIDWAY MFG, CO. FRAWKLM PARK ILL [orn wm Jeno. [vseoou, ‘DESC. 200 svi ON TROL ERIZ0: AOE-91383-BO00 SCHEMATIC PART NO. MOSt-00932-B030

Page 42

THE SCRATCHPAD AND V RAM ADDRESSER

The 2114 RAMS in the number 4 row are used as ‘‘scratchpad’’ memory.

Temporary data such as the number of credits or the high score is stored in scratchpad.

These RAMS also store the first player's frame while the second player has control and

vice versa. CPU commands and character positions can be held in the scratchpad.

Beacuse the scratchpad RAMS store information that can affect the video image as well as the program routine their addressing and outputs must be synchronized with system timing and the monitor scanning rates. The CPU address bus is buffered through chips 6R and 6S to the AB (buffered address) bus. The vertical and horizontal timing signals are processed through chip 5S to the AB bus. When the 2H signal is low

the outputs of 5S will be tri-state and the buffers will control the AB bus. When the 2H signal is high the buffers will be in tri-state and 5S will pass the vertical and horizontal timing signals to the AB bus. The component at location 5S will be either an NVC284 custom integrated circuit or a small printed circuit board with TTL chips. This is the VRAM ADDRESSER. The horizontal timing signals on pins 3 through 7 and the vertical timing

signals on pins 9 through 13 are Xored by the chips at U7, U8 and U9. The output of an

XOR gate will be low whenever its inputs are both high or both low. Note that one of the

inputs on each of these XOR gates is connected to pin number 1 of U10. When the FLIP signal is low the XOR gates will pass the vertical and horizontal timing signals. When the FLIP signal is high the outputs of the XOR gates will be the inverse (opposite) of the

vertical and horizontal timing signals. Another way to look at this circuit is to consider

the XOR outputs as a ten bit address bus. When the FLIP signal is low the highest

address would be 1111111111, the second highest address 1111111110 and the third highest 1111111101, etc. When the FLIP signal is high these addresses will become 0000000000, 0000000001 and 0000000010 respectively. This is how the image on the

monitor screen is flipped upside down for the table model games. The FLIP signal goes high for the second player in a table model game and the video circuits and scratchpad

RAMS are addressed backwards.

Page 43

From the outputs of the XOR gates the HP and VP signals are fed to the

multiplexers at U1 through U6. The SELECT signal on pin number 1 of U4 through U6

determines whether word-A or word-B will appear on the Y outputs. The 256H signal is

used as the SELECT line for multiplexers U1, U2 and U3. The 74LS257 chips at U1

through U3 are tri-state devices. When pin 15 on these three chips is high the Y outputs

will be in the tri-state mode. When pin 15 is low either word-A or word-B will appear on

the outputs. The 2H signal is inverted by an OR gate in U10 to provide the tri-state

enable to pin 15 on U1, U2 and U3. From this one can see that the V RAM, ADDRESSER is used to flip the image

on the monitor screen in the table model games and to synchronize the scratchpad with

system timing. The vertical and horizontal timing signals used by the V RAM

ADDRESSER also provide the CMP SYNC (composite sync) signal for the monitor.

The outputs of the 2114 RAMS are pushed through the component at 4H to the

buffered data bus. 4H is bi-directional and so are pins 11, 12, 13 and 14 on the

scratchpad RAMS. When the R/W (read/write) signal is low data passes through 4H

into the RAMS. When the R/W signal is high data leaves the RAMS and passes through

4H to the buffered data bus. 4H is also a tri-state device. The V RAM signal controls the

tri-state mode on 4H.

Page 44

oy

2}

4] (= 28 0m connecton

Pe PULL UP

MIDWAY MFG. CO FRANKLIN

SCHEMATIC PART NO. MOS} 00832 8032

Page 45

SCRATCHPAD AND V RAM ADDRESSER

; ,

x 0} xy . ro ~ of Fon Prk Ov! a? : o:

PERE ECE SEE in Is if | a4 sag ge5a

=F

Page 46

CHARACTER ROM CIRCUITS

Character ROMS SE and 5F generate the images on the screen. ROM 5E

generates the maze and dots. ROM 5F and the ‘‘attack’’ RAMS generate the Pac-Man

and ghosts.

One can simulate a problem in the character ROM circuit by bending a pin on

either ROM so that the pin is out of the socket. This might cause missing portions of

video, broken images or objects in the wrong places on screen. When ROM 5F is

completely out of the socket the Pac-Man and ghosts will be square blocks. The game

will play without ROM 5F but instead of characters with eyes and features, colored

square blocks will run through the maze.

A problem in the attack RAM circuit might cause the characters to change color

or eyes and other features may distort. A bad attack RAM can also cause dots and lines

to appear where they should not.

To start at the beginning note the buffered address and buffered data signals at

RAMS 3F and 3H. A problem in this area can cause the characters to appear in the

wrong piace on the screen or they might pass through the biue lines of the maze. In one

case the WE signal to RAM 3F was missing. This caused the characters to be stuck in the

upper left hand corner of the screen.

The DRO through DR7 signals from RAMS 3F and 3H are used in addressing

both the character ROMS and the attack RAMS. Signals DRO through DR7 supply

word-B to the full adders at 1F and 2F. Vertical blanking signals 1V through 128V supply

word-A. The sum or outputs of 2F are NANDED by 3E to pin number 14 of the flip-flop at 1H. The sum of adder 1F and the HBLANK (horizontal blanking) signal supply the

remaining inputs of flip-flop 1H.

The outputs of chip 1H are Xored by chip 2H to provide character addresses

CAO, CA1 and CA2. CA3, CA4 and CAS require the 4H, 8H, flip and DBO signals at 4F

and 4E chips. The buffered data bus is pushed through the flip-flops at 4D to supply

addresses CA6 through CA10 to the character ROMS. The CE signal for the character

ROMS is derived from the 2H and HBLANK signals decoded by chip 5L.

Page 47

Character data CD0 through CD7 from the character ROMS feeds the parallel

load inputs of the shift registers at 5B and 5C. From the outputs of the shift registers

(pins 12 and 15) the character data passes through the multiplexer at 5A to become

addresses AO and A1 for PROM PM1-4 at location 4A. Buffered data passes through the

flip-flops at 4B to provide addresses A2 through A6. Note that address input A7 of

PROM PM1-4 is held low permanently.

Data from PROM PM1-4 is multiplexed through chips 3A and 3B. At 3B this

data becomes signals COLO through COL3 which address the ‘‘color’’ PROM at location

7F. Through 3A it becomes input data for the attack RAMS.

Page 48

ov avon 4 .

ny wow

4 ..>
a“een2
iei9

am 7 fe} ae z Q eS t e °

wh aw » vol * aah ¥ Me. 4

Page 49

ATTACK RAM CIRCUITS

Addressing for the attack RAMS starts with the DRO through DR7 signals from

RAMS 3F and 3H. First, the DR signals are parallel loaded into counters 1E and 2E.

When the CNTR LD (counter load) signal goes low the DR signals will appear on the

counter outputs as RAO through RA7. If there is a problem with the RA (ram address) signals the Pac-Man and ghosts

might be split into sections either vertically or horizontally. The characters might also

appear in the wrong places on the screen. All of the RA lines should be pulsing. If one

finds an RA line stuck low or high the counter or DR signal associated with that line is

probably faulty. To determine which RA line carries the problem, use a jumper wire

connected to common or logic ground to force each RA line low one at a time.

IMPORTANT: If a pulsing output is forced low for too long the component might be

damaged. It is recommended that one force the RA lines low for no more than 5 or 10

seconds at a time. When an RA line is forced low the characters will split or move to

another position on the screen. An RA line that does not cause a change in the characters

when it is forced low is bad. Remember that a bad attack RAM might hold an RA signal

low. The CNTR LD signal on pin 9 of counters 1E and 2E comes from pin 8 of the

NAND gate at 4C. Note the three sections of NAND gates at 4C. The first section (pins 1,

  • and 3) inverts the signal from pin number 5 of flip-flop 4B. The second section nands the result of the first section with the signal from pin 6 of 4B. The third section (pins 8, 9,

and 10) nands the output of the second section with the result of the 1H, 2H, 4H and 8H

signals from gates 2P and 3P. Note also that pin 6 of the NAND gate at 3P is strobing

flip-flop 4B and the H BLANK signal is connected to pin number 7 of 4B. The signal on

pin 4 of flip-flop 4B is the result of the 256H and MATCH signals at NAND gate 5N. As

one can see a faulty signal anywhere in these circuits will cause an incorrect CNTR LD

signal and distortion of the moving characters. The 6 MHz signal is used to clock the counters at 1E and 2E and it also provided

WE (write enable) for the attack RAMS. Although the schematic shows eight attack

RAMS only locations 2A, 2B, 2C and 2D are used. Acceptable substitutes for the attack

Page 50

RAMS are numbers 93415, MB8125 and SC42439. Note that the OBJ ON (object on) signal at pin number 1 of the attack RAMS is coming from flip-flop 4B where it was also used in the CNTR LD circuit. Data enters each attack RAM on pin 15. The attack RAM data leaving pin 7 is sent to either latch 3C or latch 3D (only one of these components are used on each board). From the latch this attack RAM data takes two paths. Like data from PROM

PM1-4 it can either pass through multiplexer 3A and return to the attack RAM inputs or

it can pass through multiplexer 3B to address the color PROM at location 7F. A faulty attack RAM can cause the characters or their eyes to change color. The

Pac-Man might disappear or the ghosts might be invisible except for a pair of eyes. If the

attack RAM is only partially faulty, lines and dots might appear on the screen. The easiest way to determine which attack RAM is faulty, is to momentarily

force the output of each RAM high and to observe the screen. Connect one end of a

jumper wire to +5VDC and use the other end to probe pin number 7 on each RAM.

IMPORTANT: If a pulsing output is forced high for too long the component might be

damaged. It is recommended that one force the RAM outputs high for no more than 5 or

40 seconds at a time. One may choose to use the switch 8 freeze option (See Section on

Control Input Circuits) to make any change on the screen easier to see.

Each attack RAM will cause a change in the Pac-Man or ghosts when its output

is forced high. (These RAMS do not affect the characters with nicknames during the

attract mode.) For example, RAM 2B will cause Inky to turn red and the characters eyes to turn blue when its output is forced high. The purpose of forcing the attack RAM

outputs high is to determine which RAM is associated with the symptoms. If the

symptoms are blue eyes and Inky is red and if RAM 2A causes the Pac-Man to turn red,

2B does nothing, 2C causes Clyde to turn blue and 2D causes the Pac-Man to disappear,

then RAM 2B is faulty. RAM 2B was already faulty so forcing its output high caused no

change in the characters. Of course the symptoms might also be caused by a broken

trace from the output of the RAM to the input of the latch. If the symptom is lines on the

screen, one of the RAMS will probably cause the lines to disappear when its output if

forced high. Change the RAM that causes the lines to disappear.

Page 51

ATTACK RAM CIRCUITS

Page 52

THE COLOR PROM

The ‘‘color’’ PROM PM-1 at location 7F receives the COL signals on its address inputs. Note that address input A4 is held low through a set of jumper pads. If these pads are disconnected and A4 is allowed to go high there will be no color output to the

monitor. The four COL signals can address sixteen different eight bit words in the color

PROM. Each word will offer a different combination of red, green and blue signals to the

monitor. The eight bit word will also determine the intensity of each color. Examine the DO, D1 and D2 outputs on pin numbers 1, 2 and 3 of the color

PROM. If pin number 1 goes high current will pass through a one thousand ohm resistor and the red color will be low intensity. If pin 2 goes high the red color will be more

intense and if pin 3 goes high current passses through only 220 ohms for very intense

red. A ‘‘resistor ladder’’ circuit is also used for the green and blue signals. The color at a given point on the monitor screen is determined by the

combination of the red, green and blue signals from PROM PM1-1. For example, the

eight bit word 01010100 will produce a color mixture of low intensity blue, medium

intensity green and high intensity red. The word 40000100 will turn on the red and blue

signals to produce purple. The word 10100100 mixes equal parts of red, green and blue

to produce white.

COLOR PROM

893/220 BLue aZ0m 2g 220, [76 ]oreen

Page 53

AUDIO CIRCUITRY

ABO through AB3 from the buffered address bus and 4H through 32H from the

system timing bus are multiplexed by the chip at location 3L and then used to address

RAMS 2K and 2L. These RAMS are 16 X 4 (16 words by 4 bits per word) bipolar chips

and either number 74S89 or 82S25 can be used. The 74LS157 at location 3L will pass the

buffered address signals to the RAMS when its select input on pin number 1 is low. Note

that the signa! on pin 1 of 3L is actually the 2H signal which has been buffered by the

XOR gate at 4F. When the select input is high the H signals will pass through 3L to

addres the RAMS.

Buffered data lines DBO through DB3 and the 2Q, 3Q, 4Q and 5Q outputs from

chip 1L are multiplexed at 3K to supply data to RAMS 2K and 2L. The 74LS158

multiplexer at location 3K is identical to a 74LS157 except that its outputs are inverting.

PROM PM1-2 at location 3M is addressed by the 1H through 32H signals. Note that WRO supplies the A6 input and the A7 input is held low through a set of jumper pads. The 4 bit word on the PROM outputs is used to clock chips 1L and 2M and to clear

chip 2M. The D1 output is used as WE (write enable) to RAM 2K. WRi supplies the WE

input on RAM 2L. It is interesting to note that the chip select input on PROM PM1-2 is

driven by the 6M* signal which is faster than the clocking for the Z80 CPU.

With the circuitry described so far we can address and load data into the RAMS

and PROM PM1-2 will control the flow of data from the RAMS through chips 1K and 1L

to the ‘‘sound’’ PROM PM1-3. The signals sent to the final audio stage will have come

from the sound PROM.

The 4 bit words from RAMS 2K and 2L are added by the 74LS283 at location

1K. The sum is passed through 1L to address the sound PROM. Address inputs A5, A6

and A7 of the sound PROM are driven directly from the outputs of RAM 2K.

The four lines of data leaving the sound PROM enter the 5D, 6D, 7D and 8D

inputs of chip 2M.

Page 54

FINAL AUDIO STAGES

In this last section of the audio circuitry, digital sound information from PROM

4M must pass through flip-flops 2M and then be reduced or mixed to a single line of

analog data for the final amplifier at 11A. The digital sound information enters 2M at the 5D, 6D, 7D and 8D inputs. 2M

is clocked by pin number 10 of PROM 3M and cleared by the ‘‘sound on’’ signal from pin

1 of either 7K or 8K (only one of these chips are used in each game). The ‘‘sound on’’

signal goes high to enable 2M. The sound information leaves 2M on its 5Q, 6Q, 7Q and 8Q outputs and is still

in digital form. Note that each of these four outputs are connected to a resistor and that

after resistors R6, R7, R8 and R9, the four lines are shorted together. In this way each

input on the chip at 1N sees all four sound lines. The chip.at 1N contains four electronic

switches. Look at the bottom switch in schematic on page 54. Information will enter pin 8

and pass to pin 9 only when the control pin number 6 is high. The sound lines pass

through these switches unchanged except that each switch offers some slight resistance.

As one can see the control pins on 1N are driven by the 1Q, 2Q, 3Q and 4Q outputs of

2M. The signals on the electronic switch outputs are no longer of a TTL level (high near

+5VDC and low near 0 volts) and may be considered analog. Each switch output is

passed through a resistor and then once again the four sound lines are shorted together.

Note capacitor C1 at the junction of the four lines, if it is shorted, ground would pass

through it and hold the junction low causing no audio signal to the amplifier. From capacitor C1 this signal line of sound information passes through the volume control (10K potentiometer) to input pins 6 and 9 of the amplifier at 11A. An easy way to check the audio amplifier is to tap your fingers underneath the

board on the input pins of the amplifier. If you hear a loud thumping or scratching

through the speaker, the amplifier is probably good. The game will lose all sound if + 16VDC does not reach pin 14 of the amplifier,

if the amplifier itself is bad or if the volume control is open. Naturally, if there is a loose

connection to the speaker or if the speaker is bad all sound will be lost. If a loud

Page 55

humming occurs continuously, the amplifier or one of the capacitors near it may be bad.

Humming can also be caused by a bad filter capacitor on the + 16VDC line or if 12VAC is

not reaching pin X or pin W on the main connector.

If only part of the sound is missing or distorted it is recommended that one start

at the outputs of 1N and work backwards through 2M and on. As one can see, if a switch

in chip 1N were bad any sound coming through that switch would be effected. If instead

of sound only clicking is heard, check RAMS 2K and 2L and PROM 3M. Remember,

most sounds can be checked by closing the movement, start or coin switches during the test mode and don’t forget to use the switch number 8 freeze option for troubleshooting sounds that occur briefly and only once during a game, like the bonus sound.

Page 56

1X8 OR 1K XO SIP

RM

Bree 3L 7608157

wa uwi877 MEAT S10 {—F]sreaxer

Lh }sreaner A¥LINDYID OIGNY

Page 57

MS. PAC-MAN AUXILIARY BOARD (PC A804-91415-B617)

To determine which board (the main logic board or the Ms. Pac-Man auxiliary

board) is faulty, first remove the ribbon cable from the 40 pin socket at location 6B on the

main logic board. Then remove the Z80 from the auxiliary board and insert it into socket

6B on the main logic board. If the main logic board is good the game will function as a

Pac-Man except that Ms. Pac-Man will eat the dots and her mouth will open 180°. To

completely convert the main logic board to Pac-Man simply change the character ROMS

at locations 5E and 5F.

The main logic board and the program ROMS are identical in both Pac-Man

and Ms. Pac-Man. The Ms. Pac-Man auxiliary board periodically interrupts the main

program to create the new mazes and game patterns. The character ROMS at 5E and 5F

add her bow, lipstick and glamour.

Page 58

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 59

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 60

MS. PAC-MAN UR, MOY MEE. CO. 1OTSO W. GRAND AYE FRANKLIN PARK ILL. O13! WIRING SCHEMATIC PART WO, HOS! 0OSBB- A003,

MS, P&G- M40) AUX. BD.

CREDIT BYPASS PC.

GAME LOGIC BOARD PC. A082 -91375-A000 -B000

Page 61

momiTon ungaeace

uu |-cnay \ pot |

on

a

| ne ce : PAC -MAN UR. ' MiOnIY MFG. CO. 1OTSO W. GRAND AYE. 1 FRANKLIN PARIC ILL. GOL

WIRING SCHEMATIC PART WO. WOS!-00932-A0:4

c ur-go xromuen go c¥c SVS? EeGRMER $0.6E:

CREDIT BYPASS PC.

GAME LOGIC BOARD ©. A0B2-91375-A000 -BOOO

Page 62

OOO bee . Ses +,

Page 63

PAC-MAN

PC A082-91375-A000

CHIP NUMBER FUNCTION

74LS00 Quad 2 Input Nand 74LS02 Quad 2 Input Nor

74LS08 Quad 2 Input And

74LS10 Triple 3 Input Nand

74LS20 Dual 4 Input Nand 74LS42 BCD to Decimal Decoder 74LS74 Dual ‘‘D"’ Flip-Flop

74LS75 Quad Latch

74LS86 Quad 2 Input Exclusive or

74889 64 Bit Ram 16 x4

74LS107 Dual ‘‘JK”’ Flip-Flop 74LS138 3 to 8 Line Decoder 74LS139 Dual 2 to 4 Line Decoder

74LS157 Quad 2 to 1 Line Multiplexer

74LS158 Quad 2 to 1 Line Multiplexer Inverting

74LS161 4 Bit Binary Counter

74LS174 Hex ‘'D”’ Flip-Flop

74LS194 8 Bit Shift Register

74LS245 Octal Bus Transceiver

74LS259 8 Bit Addressable Latch 74LS273 Octal ‘‘D’’ Flip-Flop 74LS283 4 Bit Full Adder 74LS367 Hex Bus Driver .T4LS368 Hex Bus Driver Inverting 74LS377 Octal ‘‘D”’ Flip-Flop 280 CPU M377 - LM1877 Dual Audio Amplifier

NVC284 Custom V Ram Addresser NVC285 Custom Z80 Sync Buss Controller

cD4066 Quad Bilateral Switch

Page 64

CHIP NUMBER FUNCTION

2114 Ram 1K x4

1M5623 Prom 256 x 4

7603 Prom 32 x8 MCM 2532 Prom 4K x8

SL 4239 Ram 1K x1

93415 Ram 1K x1 27LS00 Ram 1K x1 MB 8125 Ram 1K x1 CD 4099 8 Bit Addressable Latch

N8T245 Octal Bus Transceiver

54LS174 Hex ‘‘D’’ Flip-Flop

MB7052 Prom 256 x 4

MB7051 Prom 32 x8

8304 Octal Bus Transceiver

ADDITIONAL DEVICES

18.4320 Crystal 78GVIC Voltage Regulator

D44VM4 Transistor NPN D40K1 Transistor NPN

2N3391 Transistor NPN

1N4004 Diode A15 Diode

1N914B Diode

1N4737 6.2V Zener Diode

Page 65

SERVICE BULLETIN

GAME: PAC-MAN

SUBJECT: Custom Chips 6-D and 5-S

When the custom chips are not available due to a supply problem the following alternate plug in units will be used.

  • At location 6-D PC 082-91383-B000 Z80 sync buss controller.
  • At location 5-S PC 082-91384-B000 V-Ram Addresser.

PAC - MAN

V- RAM ADDRESSER (284)

# A082-91384-B000

CHIP NUMBER FUNCTION

74LS02 Quad 2 Input Nor 74LS86 Quad 2 Input Exclusive or 74LS157 Quad 2 to 1 Line Multiplexer 74LS257 Quad 2 to 1 Line Multiplexer-Tri State

Z-80 SYNC BUSS CONTROLLER (285)

# A082-91383-B000

74LS02 Quad 2 Input Nor

74LS74 Dual ‘'D’’ Flip-Flop

74LS139 Dual 2 to 4 Line Decoder

74LS244 Octal Buffers - Tri State 74LS374 Octal ‘‘D’’ Flip-Flop-Tri State

Page 66

MS. PAC-MAN

AUXILIARY P. C. A084-91415-B617

CHIP NUMBER FUNCTION

280 CPU 2532 4K X 8 EPROM 2716 2K X8 EPROM

CG820 Custom Component

CG821 Custom Component

CG822 Custom Component

CG823 Custom Component

Page 67

CABLE — MIDCO _ TELEX NO. 72-1596

MIDWAY MFG. co. PHONE: AREA CODE 312 451-1360 A BALLY COMPANY CHICAGO PHONE: 992-2250

10750 W. GRAND AVENUE e FRANKLIN PARK, ILL. 60131

February 12, 1982

SERVICE BULLETIN

GAME: MS. PAC-MAN

SUBJECT: MS. PAC-MAN MAIN LOGIC BOARD (PC A082-91375-B000)

  • The main ‘‘Ms. Pac-Man”’ logic board is the same logic board as in Pac-Man.
  • There are two minor changes:

A. Character Proms at 5E and 5F are Ms. Pac-Man type.

B. The Z80 is removed and inserted into Ms. Pac-Man auxiliary board (PC A084-91415-B617).

Andy Ducay Service Manager

AD/dd

Page 68

INSTRUCTIONS FOR MODIFICATION OF PAC-MAN GAME PCB

THE FOLLOWING ARE INSTRUCTIONS FOR MODIFYING PAC-MAN

PCB SUCH THAT @ THE DEGREE OF DIFFICULTY OF THE GAME

IS INCREASED.

<<}

“eal § 068. connected, the game When this Jumper pad is

becomes more difficult.

Page 69

CABLE — MIDCO TELEX NO. 72-1596

MIDWAY MFG. CO. PHONE: AREA CODE 312 451-1360 A BALLY COMPANY CHICAGO PHONE: 992-2250

10750 W. GRAND AVENUE e FRANKLIN PARK, ILL. 601317

December 3, 1980

SERVICE BULLETIN

GAME: PAC-MAN

SUBJECT: STATIC CONDITION CAUSING A FALSE RAM AND ROM TEST.

MODIFICATION:

  • ORDER FROM MIDWAY’S SERVICE DEPARTMENT A ANTI-STATIC KIT PC A082-91389-A000 AND INSTALL AS SHOWN IN INSTRUCTION DIAGRAM. (FIGURE #1).
  • CHECK GAME OUT ELECTRICALLY.

ANDY DUCAY SERVICE MANAGER

Page 70

ANTL-STATIC INSTALLATION INSTRUCTIONS FIGURE #1

EXISTING CABLE

PART NO. [QTY ‘A0B2-91389-A000| | (001 7-00042-0237 9017-00101 -0082 | 3000 -17246-0300 0017-00101-0551| 0017-00104-0002| 0017-001 03-0005. 0017-00104-0062] 2 0017-00104-0003 6 SPLIT LOCK WSHR 6-32 HEX NUT -|-|-|-|>]~

‘NOTE: GROUND STRAP TO BE CONNECTED TO EXISTING GROUND STUD

MIDWAY MFG. CO. ABALLY COMPANY MOS1—00866—A019

Page 71

to be the most popular girl in the game world.

—tr-T

ey 2 al ve higher poimt values wi rer ae TL L aL [a j