CATHODE RAY TOMES

Super Chase Operating Manual

Super Chase (Taito America Corporation) · Operating Manual · 14 pages · 2 sections · original scan

Page 1

SUPER CHASE

OPERATING MANUAL

eg 2

TAITO AMERICA CORPORATION 390 Holbrook Drive, Wheeling, IL 60090 Tel. (708) 520-9280 © Fax (708) 520-1309

Page 2

Table of Contents Page Number

Installation ooo. .cccccccccceecscenscescereeseeseeeuseeereeeeeeeaeetesiectenseesreetsenteterecstnaeeees 1

Game Operation & Play Instructions ........cecccccceseeeseeeesteteereteteeeeneecsserentas 2 Self-Test Mode oo... ccecccceeseecceeesecceeeceeeeeeceesetsaecteeeeceensesessseeseneensreneneeeees 3

SOrViCing oe. eecececeee ce eesee cet e ects cenee cnet sesenseeceeeeuetessneeeneseetieserteninsetneeneteaa 8 Sub-Assembly Illustrations ....0... ccc ccceeeccececeeecesensteesntenesrtesteeseneeats 9 Wiring Diagram......cccccceecseceseteecceeceterenectteseeenseseeeneness Center Spread

Page 3

I. GAME INSPECTION Super Chase has been thoroughly tested and readied for operation at the factory and should not require any special set-up procedure. However it is suggested that upon receiving your game you examine the following to further insure the game is in proper working condition:

CHECK: Plug-in connectors are firmly seated. All player contro! connections are complete. No loose components on PC board. Fuses are installed firmly in holders. Coin mechanisms are operating properly. oovuccden No loose foriegn objects in cabinet (screws, components, etc.) which may cause shorting and result in damage to the game. If problems do occur or technical assistance is required, please call our customer service department at 708/520-9280.

Il, POWER REQUIREMENTS The game is shipped ready for operation at 120VAC, 60 Hz with a power consumption of approximately 350 watts.

CAUTION FOR SAFE OPERATION IT IS STRONGLY RECOMMENDED THE CABINET BE PROPERLY GROUNDED. THIS GAME IS EQUIPPED WITH A THREE-CONDUCTOR POWER CABLE. THE THIRD PRONG (ROUND IN SHAPE) WILL AUTOMATICALLY GROUND THE GAME WHEN PLUGGED INTO A PROPERLY GROUNDED THREE- PRONG RECEPTACLE. IF IT BECOMES NECESSARY TO USE AN ADAPTOR, THE GROUNDING LUG OR WIRE ON THE ADAPTOR MUST BE PROPERLY GROUNDED TO ASSURE SAFE OPERATION.

Ill. GAME INSTALLATION The following precautions should be followed when installing the game: Handle the game with care so as not to damage the fragile picture tube. Do NOT install the game in direct sunlight or near a heat source. Doing so might cause the internal temperature of the game to exceed its maximum operating temperature and could result in damage to the game’s components. Do not install the game in excessively dusty or damp environments. oe

Page 4

UPER CHASE

PLAY INSTRUCTIONS The player is driving different vehicles during the different rounds. The rounds take place in different cities. The player must chase and apprend the various criminals according to radio dispatch, To accomplish this he must locate the target vehicle, catch up to it, and repeatedly crash into it. This will put the criminal’s vehicle out of commission and allow them to be apprehended. To aid the player there is a map on the right side of screen showing the distance between the two vehicles. On the left side of the screen is the “crash” gauge. This shows the number of crashes needed to apprehend the crinimals. On the bottom of the screen is shown the number of nitro bursts left. When the player has caught up to the criminal car, the flashing lamp comes on, the siren is sounded, and the timer is extended. The player may continue the game when the optional “Continue Play” feature is set on in the configuration setup. Round 1 starts off in Beverly Hills. The player drives a red sports car and must chase the criminals in a blue convertible. Round 2 is in Texas with the player driving a truck. This time the criminals are getting away in a truck, Round 3 takes place in New Orleans with the player driving a Jeep. The criminals are also making their getaway in a Jeep. This time a helicopter and some firends of the criminals make the chase more difficult. Round 4 has the player in a sports car chasing the criminals around The Big Apple. The criminals, who are in a sports car, have some friends on motorcycles who are out to thwart the player. He must overcome them. Round 5 takes place in Chicago—many believe it’s the best! This one is only for the skilled player!

PLAY HINTS Avoid contact with vehicles other than the criminal’s. Hitting the other vehicles or running off the course will result in loss of time. Bump the criminal's vehicle from inside the curves. Crash the criminal’s car from the side it does more damage!

Page 5

aa

TEST MODE To enter test mode, press test switch anytime the power is on. The test switch is located on a bracket inside the coin door.

To exit from the test mode, choose “exit” by pressing Nitro Button on shift. When “exit” is highlighted press the start button. The machine will then reset iiself, and enter into the game mode. The test mode menu is shown below. A general explanation of each function is provided on the side.

Crosshatch, Color Bars for monitor setup TEST MODE MENU Steering, Accelerator, MONITOR TEST and Switch testing

SWITCH TEST Sounds and Volume Control testing SOUND TEST Adjustment of coins, CONFIGURATION time difficulty, etc. MOTOR TEST Test flashing Header Lamps (LAMP TEST] ADJUSTMENT Adjust zero position of Steering and Accelerator HI SCORE RESET Reset high score to FACTORY SETTING predetermined value

EXIT Reset configuration to factory setting

To select the desired item in the test menu press Nitro Button on shift. This will move the red highlight up or down. Pressing the Start Button on the desired highlighted item will select that particular item.

  • ee >
Page 6

ia

MONITOR TEST

In this test the crosshatch and color bar patterns are displayed on the screen. When monitor test is selected, press the Start Button to enter the tesi. Pressing the Start Button once more will display the color bar pattern. The crosshatch pattern is used to adjust horizontal and vertical size of the video. This pattern can be used to check convergence and color impurity. The color bar pattern is used to adjust the brightness and contrast. Remember, for the most part adusting the grid and screen controls will not be necessary.

SWITCH TEST

Select Switch Test from the menu and press the Start Button to enter. The display will look as shown.

COIN A: OFF COIN B: START: SHIFT: OFF OFF OFF SERVICE: OFF

NITRO: HANDLE: ACCEL: OFF 0000 OFF SOUND VOLUME: 0013 - - - OOFE

SOUND TEST

Select the sound test option from the menu and press the Start Switch. The display will look as shown:

SOUND CODE: SOUND VOLUME: EXIT

Pressing the Nitro Button selects the function by highlighting it in red. Use the Shift Handle to change the sound code. When the start button is pressed the particular sound determined by the sound code is played. By turning the Volume Pot the visual indicator on the screen will change. To exit, select the exit function and press the Start Button.

4 S\ gat — |

Page 7

oat

CONFIGURATION Select the configuration function from the menu and press Start to enter. The display will appear as follows.

ATTRACT SOUND:ONOFF
DIFFICULTY:NORMALHARDVERYHARDEASY
CABINET TYPE:DXUR
CONTINUE PLAY:WITHWITHOUT

COIN A: 1-4 COIN(S) / 1-6 CREDITS CONTINUE COIN: 1-4 COIN(S) CONTINUE

HANDLE DIRECTION:NORMALREVERSE
TARGET DAMAGE:RESETCONTINUE
TIME SETTING:STANDARDLONGVERY LONGSHORT
ROUND 1:30-50-6533-53-5836-56-7127-65-60
ROUND 2:55-65-6558-68-6861-71-7153-60-60
ROUND 3:55-60-6058-63-6361-66-6650-55-55
ROUND 4:70-70-7073-73-7376-76-7665-65-65
ROUND 5:50-70-7053-73-7356-76-7645-65-65
HANDLE VIBRATION:ONOFF
SEAT VIBRATION:ONOFF
NITRO VIBRATION:ONOFF

TV MONITOR TYPE: WITH MIRROR WITHOUT MIRROR AGING: OFF ON

An explanation of each of the above functions is given below: ATTRACT SOUND—sounds enabled/disabled in game over DIFFICULTY—four (4} difficulty levels available (normal, hard, very hard, easy] CABINET TYPE—deluxe or upright. Choose upright. COIN A—setting of the two coin slots CONTINUE COIN—coin setting for continuation of play HANDLE DIRECTION—change steering wheel direction (normal, normal turn-reverse, reverse turn. TARGET DAMAGE—reset, damage of criminal car is not shown continue, criminal car damage is shown

Page 8

Sue

TIME SETTING—the four (4] time settings are self-explanatory (short is difficult, very long is easy}. By choosing one of the 4 times, the times of the rounds are set. Time to find Criminal Car

ROUND 1: 35 55 50 4 4 Time at Game Start Continuation Time

HANDLE VIBRATION—deluxe only, set to OFF SEAT VIBRATION—deluxe only, set to OFF NITRO VIBRATION—deluxe only, set to OFF TV MONITOR TYPE—upright is without a mirror AGING MODE—deluxe only, set to OFF To change a function, select it by using the steering wheel. When the desired item is reached, press the Start Button to change. When you are finished, press the Test Switch. You will be asked whether you want save the changed data. When YES is selected the data is saved.

MOTOR TEST (Lamp Test) When this test is selected the display will appear as below:

PATROL LAMP: OFF-ON EXIT

When the Patrol Lamp is selected and the Start Button is pressed the display will change to ON and the top incandescent lamp will light. When the Start Button is pressed the display will change to OFF. The top incandescent lamp will turn off. To exit this test, select EXIT and press the Start Switch.

6 SY gt —~

Page 9

ADJUSTMENTS

When this test is selected the display will appear as below.

HANDLE ADUST: 0000 EXIT

To adjust the Steering Wheel, select adjustments using the Nitro Button. With the Steering Wheel in the center of travel press Start Button. The Steering Wheel is now adjusted.

To exit, select the EXIT function and press Start.

FACTORY SETTINGS

When this function is selected and the Start Button is pressed you will be asked whether you want to default to the factory settings. If you select YES and press the Start Button, the following settings will be selected.

ATTRACT SOUND DIFFICULTY CABINET TYPE COIN A / 1 CREDIT(S) CONTINUE PRIZE 31 COIN CONTINUE HANDLE DIRECTION :NORMAL TARGET DAMAGE :RESET TIME SETTING :STANDARD ROUND 1 :30-50-65 ROUND 2 155-65-65 ROUND 3 :55-60-60 ROUND 4 :70-70-70 ROUND 5 :50-70-70

HANDLE VIBRATION :OFF SEAT VIBRATION sOFF TV MONITOR TYPE =: WITHOUT MIRROR AGING MODE :OFF

Page 10

ast

SERVICING Let’s get the warnings out of the way first.

WARNING: © This game must be properly grounded. Failure to do so may result in damage to game. ® Always turn power OFF {remove the plug] when performing any service to the game.
  • Always replace fuses with the same value and type for continued protection.
  • Replace line cord if damaged. © Replace lamps with the same watiage. Never use a larger watt lamp.

LAMP REPLACEMENT To replace the header fluorescent lamp and flashing lamps remove the screws on the top of the cabinet that secures the header glass hold down bracket. Remove the bracket and glass to gain access to the lamps. Remove and replace the defective lamp.

FUSE REPLACEMENT The fuses are all located on the transformer board, except for those on the monitor itself. There is one for the main power line, one for the audio power, and one each on the lamp driver board for the two flashing lamps.

MONITOR There is a remote board located near the coin door to adjust the monitor. Brightness, contrast, sync., and size can be adjusted using this board. To check the fuse on the monitor or to gain access to the connectors, remove the access plate on the rear of the cabinet. To remove the monitor, remove the two bolts that hold the control panel to the cabinet. Open the control panel. Remove the monitor glass and bezel. There are three bolts above and below the picture tube. These must be removed. Disconnect the video and power cable from the monitor. Now remove the monitor from the front of the cabinet.

LOGIC BOARD To remove the logic board, open the back door. Remove the connectors from the logic board. Unscrew the ground plane from the cabinet. Lift the logic board and ground plane from the cabinet.

SERVICE BRACKET Located on a bracket inside of the coin door are the coin meter, volume control, service switch, and the test switch. 8 Sgt —~

Page 11

SUPER CHASE

FOOT PEDAL ASSEMBLY

PART/ASSY. NO. DESCRIPTION QUANTITY 15-423200 Base Assy. 15-430300 Brass Bushing

15-429600 Pedal Assy.

23-140700 Microswitch 30.028100 #4-A0 x 3/4 Phillips Pan Head Machine Screw 30-167400 #440 x 3/8 Phillips Round Head Screw 30-126600 #4-40 Hex Keps Nut 30-178800 Washer .312 0.D. x .125 1.D. x .016 Th. 15-430100 Shaft 30093200 ERing 26-330600 One Side Adhesive Damper ON Awuuu ps ‘m|rmj—lalalr |r]

30773500 ‘Compression Spring

CALL TAITO FOR PARTS AT (708) 520-9280

Page 12

Sue

(2) STEERING ASSEMBLY 14 gNOT SHOWN

PART/ASSY. NO. DESCRIPTION 15-4205-00 | Top Plote Assembly 98-0789-00 | Base Plate 15-4043-.00 | Top Plote 18 _15-4219.00 | Base Plate 15-409400 | Bushing 15:4114.00 | Bearing 19 15-4217-00 | Urethane Tube 30.0981-00 | C Ring 20 15.4214.00 | Pin 30-1760-00 | 10-32 x 3/8" Phil. Hd. w/Int. Washer 15-4098.00 | Mounting Plote Assembly : 30.0931.00 15-4111-00 | Mounting Plate E Ring

15-4094.00 |_Bushing 98.0818.00 | Bracket w/Pot Assembly 15-4114-00 | Bearing 15-9373.00 | Bracket for Pat. 30.0981.00 |_C Ring 72-2094-00 | 5K Pot. Clarastat 15-4334-00 | 24 T Gear w/ 1/4" Bore 8/32 Thd, Housing 15-4287.00 | Steel Ring 30-2158.00 | 8.32 x 1/2" Set Screw 30-1760-00 | 10-32 x 3/8" Phil. Hd. w/Int. Washer 15-4224.00 | Bearing Spacer 15-4289.00 | Central Shoft 30.0685.00 | Spring Waster 307957.00 | Washer 20095700 | ERing 15.4113.00 | Hub 301760.00 | 10.32 x 3/8" Phillips Hd 30201400 | Woodley wint Washer 30-1475.00 | 3/8-16 Lacknut 30.7162-00 | Return Spring 15-4206.00 | Carrier Assembly i 30-1836.00 1/48 27/16 baton Wa 15-4112.00 | Bearing Cover Plate $5 Washer 30.0889-00 | 3/16" x 1-5/8" Roll Pin 15-4369-00 | Steering Wheel Inc. w/Decorative Insert

CALL TAITO FOR PARTS AT (708) 520-9280

  • ga
Page 13

Ne SHIFT LEVER ASSEMBLY

PART/ASSY. NO. DESCRIPTION QUANTITY

50-807 1-00T Handlei
50-8054-00Push Button Thumb Switch1
95-4117-00DA3 Switch1

50-8184.00 Spring 50-8392-000 Pin 50-8272.00 Top/Right Side 50-8339-00 Top Plate 43.0042.00 Screw M6 x 10 50-8346.00 Trunnion, Turbo Shifter 50-801 8-00 Rubber Stop 43-0080-00 Screw M 6x35 43-0041-00 M6 Nut 43-0983-00 M 6 Lockwasher 50-8118-00 E RingM 15 —|afe|rm}ro]—jro}-|—

50-8342-00 Switch Actuator Bar 50-8344.00 Bolt Assembly Pivot 50-8273.00 Switch Mig. Plate 50-801 8-00 Micro Switch with Roller

CALL TAITO FOR PARTS AT (708) 520-9280

  • ton
Page 14

SPEAKER ——SS—=_

CHAIN BOARD

SUPER CHASE

+12V

NOTE: rh = EARTH GND _.. = LOGIC GND ay 10KQ \ PULL-UP

ee ACCEL

am 1 Jt dt

LAMP BOARD

pn 3 +5V |

LL SOUND VOLUM | 4 ON/OFF 5 AMP IL LINE oo | NI FILTER _ | | eo | + L ; ) ¢—{Flvonescent SWITCH

J3