CATHODE RAY TOMES

Mat Mania

Mat Mania (Technos Japan (Taito America license), 1985) · Manual · 12 pages · 13 sections · original scan

Page 1

KANG BK tl ped INSTRUCTION MANUAL

OCTOBER.15,1965

MEMETRON PRESENTS

0 . 4 THE PRO WRESTLING EVE 0.2.2.

MAT MANIA™

GUPTRIGHY 10 TAITO ADERIEA CORPORATION LIGBHSED DY TECHNOS, JAPAN DIGTRIDUTED BV DEHEFTROW ING.

FOR THE SERVICE THAT KEEPS YOU GOING 512-505-2628

2350 BRICKVALE DRIVE ELKGROUE VILLAGE, IL. 60007

(Granned hu | Contteman?

Page 2

VIDEO GAME OPERATOR:

Don’t Get Involved In A Federal Crime. Don’t Buy Or Operate Copy Or Unauthorized Boards In Your Games.

Every operator who buys or operates « counterfeit or nnauthorized hoard (imported or domestic) 1s contributnig to the end of ovr industry and committing a FEDERAL CRIME, New criminal law's have recently een enacted that provide for maxinuont penalties of $250,000 or five wears im pason or both, per offense. PACH GAME IS A SEPARATE OF FENSF

TE vor haw: ary injormetion abort any Unued States, FRI contact wow (nfscar rr 208 The Strand Suite 3 Alexandria, Virginia 22314 (703) 548-8049 sement Machine Association

Page 3

IMPORTANT F.C.C. WARNING

"This Kit is intended for use only on coin operated video games manufactured after October 1, 1983, which have been verified for compliance with the requirements in Part 15 of FCC rule for class A computing devices. Improper connection of the kit or connection to any other coin operated video game not so manufactured or verified for compliance may cause unacceptable interference to radio and T.¥. reception requiring the operator to make necessary changes fo correct the interference. Memetron , Inc., takes no responsibility for kits improperly connected and those connected to games for which use is not intended.”

Page 4

WARMINE®S & NOTICES

WARTING

For safety and reliability, Memetron iInc., does not recommend or authorize any substitute parts or modifications of Memetron equipment.

Use of non-Memetron parts and modifications of game circuitry may adversely affect game performance.

Substitute parts or equipment modifications may void FCC lype acceptance.

Since this game is protected by Federal copyright, trademark and patent laws, unauthorized game-conversions may be illegal under federal Law.

This ” conversion ” principle also applies to unauthorized facimiles of Memetron Inc., equipment, logos. designs, publications, assemblies and games ( or features not deemed to be in the public domain ), whether manufactured with Memetron components or not.

VARTING

Three-Wire Plug this game must be plugged into a properly-grounded ouflet to prevent shock hazard and to assure proper game operation. Do Not use a ” cheater” plug to defeat the ground pin on the power cord , and do nol cut off the ground pin.

NOTICE

Parts salvaged from your old game are required to complete your kit. These salvaged parts MUST operate perfectly, or the converted game can not perform perform properly of safely. Always repair circutboard malfunctions and cabinet damage before conversion is attempted.

Page 5

NOTIGE

This kit is not intended for use with X-¥ monitors. Suitable monitors are the horizontal or vertical raster-type with inputs for red, green and blue video as well as negative sync. ( These inputs should be compatiable with TT1 logic levels. ) Note: Mat Mania™ uses a vertical monitor.

HOTIGE

Be sure the power supply from your old game is capable of +5ydc regulated at 6A and +12VDC regulated at 1A. These operating voltages are necessary for your Kit.

NOTIGE

Mat Mania is a registered trademark of Taito America Corp. Under License from Technos, Japan. Distributed by Memetron Inc., 1985.

NOMIC

Please make sure you clean and lubricate your old coin mechanisms. It is important that you service tham in order for this game to earn the maximum projected earnings.

RIPS PARTS LIST PROVIDED

[]PCB BOARDqa)

{] JOY STICK a)

[]CONTROL PANEL OVERLAYq)
[]PLEX! CRTa)
[]PLEX! MARQUEEq)
[]WIRING HARNESSa)
[]_INSTRUCTIONSa)
[]PLAY INSTRUCTIONSq)
[]MISC CONTROL STICKERSqa)
[]DRILLING TEMPLATEa)

[] JOYSTICK STAR a)

[]BUTTONS(4)
{]FCC CAGEQ)
Page 6

TOOLS AND SUPPLIES REQUIRED

[] SCREWDRIVER I] WIRE CUTTERS {] ELECTRIC DRILL {] SOLDERING IRON & SOLDER {] PLIERS I] PHILLIPS SCREWDRIVER {] HEX DRIVER I] 180-GRIT SANDPAPER [] FIRE ENGINE RED, SEMI-GLOSS LATEX PAINT {] GREASE PENCIL OR MARKER I] X-ACTO KNIFE [] HACKSAW or JIGSAW

CABINET

Inspect your old cabinet for any gouges or items stuck on the extremity such as chewing gum. Remove all foreign objects and fill in the gouges with any type if quick hardening wood putty. Sand to make sure the surface is smooth and wipe clean the outside of the old cabinet. Remember the reason you are converting your game is to have the earnings of a new game. Making it look like a new game will increase your earnings and player interest.

CRT & MARQUEE

Remove the new crt and marquee from the kit box. Place and center the old marquee and crt on top of the new crt and marquee. Stick masking tape on the area where you intend to cut the plexiglass. Take your grease pencil and draw a straight line to use as a cufting guide. Using your hacksaw or jigsaw cut the plexiglass down to size. Replace the new cut to size plexiglass marquee and crt cover on your game. If done correctly your game should look almost new.

Page 7

GCOMROL PANEL

Remove the old control panel buttons or joysticks. Clean and sand smooth any imperfections on the existing vynil material.

Place the template that comes with the game on the control panel in order to design the best possible positioning for your bultons, joystick and control panel instructions.

Please leave your 1 or 2 player start button holes where they are. Drill holes as needed for installation of the joystick and other buttons. Any hole thal is no longer needed we suggest plugging with wood blocks, pufty, cardboard or epoxy. Remove the backing from the rear and carefully place the control panel overlay on the old control panel being careful not to get any air bubbles in the vynil when it’s applied.

After the control panel is securely on, with an exacto knife knife or razor blade carefully cut out holes on the control panel. Next stick the joystick stars and button stickers on the control panel. Replace your buttons on the control panel and tighten them down. Return the control panel to ihe game for the next step in the kit process.

GAME PLAY INSTRUCTIONS

Your game comes with two sets of instruction decals, one fo mount horizontally and the other to mount vertically. Depending on the amount room around the Crt. After conversion choose set A or set B for installation on your game but not both.

Page 8

HOncH

Refer to the decal layout sheet for more information on graphics position.

Refer to the control panel template for control layout suggestions. é

If the control panel that you are going to use is wood and is too thick for use with the enclosed button holders, than remove the switches from the holders and shim them with spacers.

Make sure that the control panel is on straight.

PROGEDURES INSTALLING ITERBOARD WIRING

{] Disconnect the old wiring harness from the CPU board. Using the schematic drawings from your old game, carefully note the function of each wire. Label the wires if this helps.

[] Carefully remove all circutboards and the metal curcutboard panel from the game.

{] Leaving several inches of wire from the old wiring harness at each connector, cut the wires near the games coin door, moniter, player panel, power-supply and speaker wires to the new CPU-board harness. Using electrical tape, be sure to insulate all splices.

{] If your game has series-pass transistors for the power supply on a separate heatsink, remount the metal heatsink beside the power supply board.

I] Check and clean the input jack on the power-supply board. Replace any burned or damaged pins.

THANK YOU FOR YOUR PURCHOSE OF 4, MEMETRON KING KIT.

Page 9

MAIN HARNESS

MAT MANIA

SOLDER SIDE PARTS SIDE

WIRE/COLOR | SIGNAL NAME PIN NO SIGNAL NAME | WIRE/COLOR

| 22 | vio-wHT | SPEAKK GND 1p SHOOT 1 Al

AZ

|LU-RED COIN COUNTER

Qe ee LU-GRN | 1P SHOOT 2 REEN VIDEO GREEN VIDEO RED > nN

= 2 > s nr

E BL | v0 E Pos

ORG-WHT

7] a

cH rs rao PAT | raz | ras | ow =

2P RIGHT

1P DOWN GRY-YEL

BLU-GRY ime

BLUE

BLACK

BLACK

YELLOW 2P SHOOT 2

VIDEO BLUE

VIDEO SYNC ae SPEAKER [eu [ip Leet [2 starr | PRE OP eeet ha a ak jae [ze eicur | [9_[1P vow | [io [coma | 2 a a [pi2_[ 2p soor 2. | [e13_ [vine BLvE | | VIDEO. SYK. wlole a alul =

ow

SV

Page 10

DIP SWITCH SET TINGS

DIP SWITCH 1

© Coin-A 1 Coin — 1 Play 1 Coin — 2 Play 1 Coin — 3 Play 2 Coin = 1 Play

“| 1 Coin — 1 Play "1. Coin ~ 2 Play 1 Coin — 3 Play 2 Coin — 1 Play Sound for Demonstration B] Sound AR BJ Notsound @ TV-Screen Table type use

Up-right type use @ Check Program OFF ON

Don't Touch

DIP SWITCH 2

45678

on

9gl/lo9°°Pcatee of Difficulty-
222422&BhNormal
ct444=|Sj
Sccccc
geaaG&&
mmmmiKd

UTHLU Difficult

  • Suggested factory setting (normal screen)

(flipp screen vertically)|

Page 11

MAT MANIA CONTROL

s iL p1A. THRU (2 PLCS)

PUNCH

(NOTE 2) 2 4

NOTE:

1. THESE DIMENSIONS ARE TO SCALE AND

REFER TO METAL CONTROL PANELS. 2 FOR WOOD CONTROL PANELS, DRILL 5/8" bbl ie gen

HOLE COMPLETELY THROUGH. THEN DRILL

1-1/8" HOLE TO 5/16" DEPTH.

Page 12

ATTACK MARK BY JOYSTICK

The Exciting

FIGHTING MACHINE

Players enter a world of fast-paced tournament style action as they kick, slam, claw and power punch thei? way to victory against the enemy and the clock. Wrestling, kick-boxing and martial arts techniques combine for a challenging hand to-hand fighting qame in a colorful arena setting. Skillful maneuvers of the joy stick, punch and kick buttons successfully advance the SHANGHAI KID to new arenas and tougher adversaries, Realistic sound effects include “count-down” by announcer/ referee and crowd cheers. Get your kicks and knock out more profits with the complete ‘fighting machine’ conversion kit

© Copyright 1985 Pata East, U.S.A, Inc. memetron 2350 Brickvale Drive / Elk Grove Village, IL 60007 / Phone: (312) 595-2828 Telex: 210227 Ansb. Memory