CATHODE RAY TOMES

STV Sega Titan Video Manual

ST-V (Sega Titan Video Game System) (Sega Enterprises, Ltd.) · Manual · 30 pages · 5 sections · original scan

Page 1

1ST PRINTING - FB

TM

SEGA TITAN VIDEO GAME SYSTEM SERVICE MANUAL

° Before using this product, read this OWNER'S MANUAL carefully to understand the contents herein stated. ° After reading this manual, be sure to keep it available nearby the product or elsewhere convenient for referring to it anytime when necessary.

IMPORTANT!

MANUAL NO. 420 - 6170 - 01

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3

PAGE

  • HANDLING PRECAUTIONS 1
  • SPECIFICATIONS 2

NAME & POSITION OF ON-BOARD CONNECTORS, SWITCHES, ETC. MONITOR DIRECTION, HORIZONTAL FREQUENCY COIN ASSIGNMENTS AND COIN PORT CONTROL PANEL AND BOARD I/O

  • 56P CONNECTOR (JAMMA)
  • EXTENSION I/O PORT (2L12B)
  • EXTENSION I/O PORT (3L9B,4L12B)
  • OTHERS (V.R., Light Gun, and Control Panels(for Mah—jong, Hanafuda, Dial and Control Ball), etc.) ©6080

3, PLACING & REMOVING THE CARTRIDGE, AND INSTALLING THE BOARD — «

4, TEST MODE 7

A) NORMAL TEST MODE MEMORY TEST C.R.T. TEST INPUT TEST CLOCK ADJUSTMENTS SYSTEM ASSIGNMENTS COIN ASSIGNMENTS SYSTEM BOOKKEEPING BACKUP DATA CLEAR EACH GAME TEST ©@QV9OOOGLOHO

B) FACTORY TEST MODE

5, WIRING FOR THE BOARD 22

A) 2—-PLAYER SIMULTANEOUS PLAY, 6-BUTTON SPECIFICATIONS (2L12B)

B) 3-4 PLAYER SIMULTANEOUS PLAY, 3- BUTTON SPECIFICATIONS (3L9B,4L12B)

Page 4

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 5
  • HANDLING PRECAUTIONS

(1)

(2)

(3)

(4)

(5) When installing and removing the IC Board, make sure that the cabinet's main power is OFF.

Foreign bodies, such as dust on the IC Board, may cause damage (short circuit, fire, etc. due to the Board's generation of heat). Therefore, ensure the IC Board surfaces are always kept clean.

Completely connect up the IC Board's and other items’ connectors. Insufficient connector insertion may damage the IC Board. Therefore, pay careful attention to this point. Also, for the IC Board circuit inspection, only the use of a logic tester is permitted. The use of a tester is not allowed, therefore, also be careful of this point.

The applicable frequency for the monitor compatible with the ST-V Board is 15 kHz. The ST-V Board can not be used for a cabinet which employs a monitor or projection display which has 24 kHz frequency only.

The contents of the product herein described are subject to change without notice.

Page 6
  • SPECIFICATIONS

@® NAME & POSITION OF ON-BOARD CONNECTORS, SWITCHES, ETC. + In the case where the cabinet has neither the Test button nor Service button, utilize the Push SW which is on the Main Board. (SW1: Test button SW2: Service button).

+ For adjusting the sound volume, use the on-Board VR 1.

CN3 — EN2

Does not function if CNS is not connected with the Board (No. 839-0724). Also, make sure that this Board is not connected with other | Connector.

839-0724 (oo CNa CNS SWI SW2 — { | cnez ee ( || 3P — JP4 + Do not change the -

|one?_| sP3Jumper Pin inser-
| | 38PJP2tion positions shown.|

[>= - ] Jl

© RVI

CN25

CN24JAMMASPCNI9CN32

| 4P | 1 28-— [ep | [9

JAMMAC56P, P=3. 96mm) CN25 (JST NH 5P) RESERVED OUTPUT 4bit. CN19 (JST NH 12P) A/D INPUT 8Ch. CN22 (JST NH 3P) MIDI OUT CN32 (JST NH SP) EXTENSION I/O 8bit. CN27 (JST NH 3P) LIGHT GUN TRIGGER

CN24 (JST NH 4P) AUDIO LINE OUTPUT — CNI8 sist NH 6P) SERIAL COMMUNICATION

CN21 (JST NH 11P) EXTENSION I/O 8bit. CN20 (JST NH 10P) EXTENSION INPUT 8bit.

CAUTION Although a Connector similar to the one used for SEGA's SYSTEM 32 is used for the CNI18

CN21 11P

CN20 10P

ST-V BD CN24 audio output, the pin assignments are different. When using the ST - V Board for the MEGALO 50 DX, SD3, and SUPER MEGALO 2 Cabinets, make sure that the AUDIO OUT ON/OFF Switch is OFF. Also, do not connect the 4P Connectors from the Cabinet to CN24. Otherwise, ST-V or the cabinet may be damaged.

Page 7

@® MONITOR DIRECTION, HORIZONTAL FREQUENCY

MONITOR HORIZONTAL FREQUENCY HORIZONTAL 15. 7kHz

  • COIN ASSIGNMENTS AND COIN PORT
  • — Setting the Coin Chute Type (COMMON, INDIVIDUAL) COMMON (Initialization): Used for the type of cabinet whose coin acceptance is a common type for plural players. Coins inserted by each player are handled as common credits. In spite of Cabinet Type setting (or the number of players), COIN 1 and COIN 2 coin ports are used,which respectively correspond to NO.16, 56P Connector and NO. T, 56P Connector. COIN/CREDIT setting can be set for COIN 1 port and COIN 2 port separately. INDIVIDUAL Used for the type of cabinet which has a coin chute for each player, with each coin chute being able to accept coins. Coins inserted by each player are handled as that player's credits. The relationship between the cabinet type setting and the coin port is shown in the following table:
Note that COIN/CREDIT setting applies in common to each coin port.

INDIVIDUAL COIN PORT ~ CABINET TYPE PLAYER | ST—V COIN PORT SYSTEM 32 COIN PORT

iP1P_|COIN1 (eP, 16)COIN1
2P'--1P[COIN1GéP,16)COIN2
|2P(COIN 2(er,T)|COIN1The Player!
3P|TP/COTN1(56r.16)COIN8lanl
2P|COIN2(e6P,T)COIN2e
7|3P__|COIN8(seP,25)COIN1|gaemfrom
4p'“TP|COIN1Gop, 16)COIN4ing SEGA
|2P|COIN2(eP,T)COIN8Boards (Sys-
|8P|COIN8(GepP,25)COIN2tem 32, etc.)
|4P|COIN4(6P,c)COIN1

For example, neither COIN 3 port nor COIN 4 port can be used for the 2P cabinet type. The <3P COIN> and <4P COIN> of ST - V Board respectively corresponds to NO. 25 and NO. c of the 56P Connector. Connect them as applicable. Should any button on the Control Panel be wired, be sure to remove the wiring.

Cabinet Type and Coin Chute Type setting changes can be made in the TEST mode. Refer to ® SYSTEM ASSIGNMENTS and © COIN ASSIGNMENTS of Section 4 TEST MODE.

Page 8

@ CONTROL PANEL AND BOARD I/O

  • 56P CONNECTOR (JAMMA)

The following < > refers to the Coin Setting set to "INDIVIDUAL." PIN ASSIGNMENT (J AMMA) COMPONENT SIDE SOLDER SIDE

GND[| 1]A]GND
GND2/B]GND
+5V|8/C]+5V
+5V| 4]D]+5V
(NOTUSED)| 5]E|(NOTUSED)

+12V 6/ F| +12v

(NOTUSED)| 7[ H|(NOTUSED)
COINMETER18|J}COINMETER2
(NOTUSED)| S| K|(NOTUSED)
SPEAKER (+)[10]L]|SPEAKER (-)
(NOTUSED)11|Mj)(NOTUSED)
RED[12/N]GREEN
BLUE[13]P|SYNC.
GND (SYNC.)/[14|R|SERVICE
TEST(15/S|(NOTUSED)
<1PCOIN>COIN1[16]T|COIN2<2PCOIN>
1PSTART[17]U|2PSTART
1PUP18|V|2PUP
1PDOWN19}W|]2PDOWN
IPLEFT[20]X|2PLEFT
1PRIGHT[21|Y|2PRIGHT
1PSWI[22] Z|2Pswi
1PSw223/ al2Psw2
1PSW3[24|b|2PSw3
<3PCOIND>CNOT USED)| 25{[c]|(NOT USED )<4PCOIN>
(GAME SELECT)| 26 |dj(PAUSE)
GND|27[e|GND
GND[28/|f]|GND

56P P=3.96mm

2L6BCONTROLPANEL

IP START 2P START oo nan via Ki

<O>000<O> 00 0
©) 3silsiz si3eSSHSH2 SHS
PLAYER1PLAYER2

GAME SELECT (Pin NO.26, 56P Connector) Only the Multi-Cartridge mode is used. In the case where the cabinet has a button which allows the player to select the desired game, wire NO. 26 Pin. When using the SELECT button, change the setting in the TEST mode accordingly.

PAUSE (PIN NO. d, 56P Connector) used for photographing on-screen image

connect up GND and Pin NO. d to have a PAUSE function. Normally, these should not be wired. 44>

Page 9
  • EXTENSION I/O PORT (2L12B)

CN21 JST 11P 1P SW4 1P SW5 1P SW6 SW7) NOT USED 2P Sw4 2P SW5 2P SW6 (2P SW7) NOT USED GND OOOO CR oN a)

2L12B CONTROL PANEL

IP START 2P START [omne) +*70 00 ntz 0 0 O 1< O- > SHI SW2 SH8 <—O-— > SWI SH2 SW3 £)/30 0 0 els 0 00 SW4 SW5 = SW6 SW4 SWS = SW6

PLAYER 1 PLAYER 2

  • EXTENSION 1/0 PORT (3L9B, 4L12B)

1| 3P Swi 1| GND 2 3P SW2 2| GND

CN82|8, 8P SW8CN21/_8] 4P SWI

ist 9? | 4 8P START Jst ip | 4] 4P swe 5| 8P DOWN 5| 4P Sws

—6|8P UP6| 4P START
7|8P RIGHT7| 4P DOWN
8|8P LEFT8| 4P UP

~9! GND 9| 4P RIGHT 10| 4P LEFT 11] GND 4L12B CONTROL PANEL

1P START2P START3P START4P START
fe)fo)fe)fo)
chaO00vhxOO«ctxOOKhan00

|<-O-> O SW2 SW3 <-O-> O SW2 SH#3 <—O->O SH2 SHB <—O-—>O SW2 SW3

es si“ys si“ys siey SHI
Loa ——
PLAYER 1PLAYER 2PLAYER 8PLAYER 4
  • OTHERS (V. R.-, Light Gun, and Control Panels (for Mah-jong,Hanafuda,Dial and Control Ball), etc.

Refer to applicable Instruction Manual which comes with the software.

Page 10
  • PLACING & REMOVING THE CARTRIDGE, AND INSTALLING THE BOARD

When installing and removing a Cartridge, or installing the ST-V Board, ensure that the Cabinet's main power is OFF.

CAUTION When removing the Cartridge, do not try to force it, with the Holder still remaining ina secured status. Applying excessive force to the Board may cause damage such as soldering defects, etc.

When installing the Board in the Cabinet, secure all of the "L" LOCKs on the outer portions of the Board and the Board Brackets in the periphery of the Cartridge Holder to the wood base by using the wood screws which come with the Kit.

GAME _ CARTRIDGE ST-V_MAIN BOARD With the rear side facing outwards, completely insert it vertically.

CARTRIDGE HOLDER When installing or removing the Cartridge, slightly incline and bend the catch towards outside.

Page 11
  • TEST MODE

A) NORMAL TEST MODE

This mainly checks if the operation of the game board is accurate, makes monitor color adjustments, and allows for COIN ASSIGNMENTS / GAME ASSIGNMENTS setting adjustments.

SELECTION OF TEST ITEMS

  • After the power is turned ON, push the TEST button to have the following TEST TEM MENU appear on the screen.

ST-V TEST MENU

To mM Z0wH>om4 nA Poa ZmMPo-neumm MONAND-AF >><O<rz’ m mam O0ON-nNOUVHES Q mDR4ZIAC oO Oo cm mmx Cc OVE>= 4ooucHnn > APRZ-HM 34

0 >

1 S ] *1 ] ]

n m Pais zm V 0a jam ~< a

a< wo oad Z4 {o) Zz an mm ~ (De ) ad |nm | ap cm | 40

  • By pushing the SERVICE button, bring the arrow mark " >" to the desired item and press the TEST button.
  • When the test has been completed, bring " >" to EXIT and press the TEST button to have the Game mode return to the screen.

1: [ ] below EACH GAME TEST displays the name of each game which is connected to the Board. The example in the above menu indicates the case where GOLDEN AXE THE DUEL is in SLOT 1.

CAUTION The contents which are set by the user in SYSTEM ASSIGNMENTS and COIN ASSIGNMNENTS are registered when the test mode has been completed after EXIT in the menu mode. As such, if the power is turned OFF before registering the contents, the settings made are ineffective. Therefore, pay careful attention to this point.
Page 12

@ MEMORY TEST

First , check if MEMORY IC functioning on the Main Board is accurate. If the IC is in good operating condition, "GOOD" will be indicated. If there exists any malfunctioning of the IC's, "BAD" will be indicated.

MEMORY TEST PAGEI/2

*** ROM #4 *

|1c8Goop

*** RAM # & #

IcaGOOD1¢10 Goopic11 Goop
|1c24 GooD1¢26 Goop1c27 Goop
|1c28 GOOD1c80 Goopicss Goop

1c84 GooD 1cs7 Goop

__PRESS TEST BUTTON TO NEXT

After the test has been completed, press the TEST button to cause the Cartridge MEMORY TEST to be performed.

EXAMPLE: The following shows the display when four "GOLDEN AXE THE DUEL" Cartridges are inserted in the Board.

MEMORY TEST PAGE 2/2

  • # * CARTRIDGE ROM CHECK * * # CART #1 [GOLDEN AXE DUEL 1]
1€1GOOD 1¢2GOOD ICSGooD Ic4GooD
|1€6Good IcBGood 1¢18 GooD

CART #2 [GOLDEN AXE DUEL ]

IC1GOOD 1¢2GOOD ICSGoop Ic4GooD
|1€&Good 1cBGoop Ic1s GooD

CART #3 [GOLDEN AXE DUEL J

1¢1Goon 1¢2GooD ICSGooD Ic4GooD
1€5GOOD 1¢8GOOD Ic1s GooD

CART #4 (GOLDEN AXE DUEL }

1€1GOOD 1¢2GOOD IcSGood 1c4GooD
1€5GOOD 1¢@GooD 1¢18 GooD

PRESS TEST BUTTON TO EXIT

Note that the display of the slot in which the Cartridge is not inserted will be omitted.

After the test has been completed, press the TEST button to return to the menu mode.

Page 13

@ C.R.T. TEST

A) RGB COLOR ADJUSTMENT SCREEN

This page allows for checking the monitor color adjustment.

c.R.T. TEST PAGE 172

L111111111222222022288 01284567800128466780012845678801

| < White

« Red

| « Green

ae ; < Blue i

VICE BUTTON TO OTHER PAGE | TEST BUTTON TO RETURN

Each of the R (red), G (green) and B (blue) colors is darkest at the left-hand end and becomes brighter in 31 gradations towards the right-hand end. The monitor brightness is satisfactory if the white color bar is black at the left-hand end and white at the right-hand end.

B) MONITOR SIZE ADJUSTMENT SCREEN

This page allows for monitor size to be checked.

PAGE 272

1 1 im ~

SERVICE BUTTON TO OTHER PAGE |_ TEST BUTTON TO RETURN

Make adjustments in a manner so that the checkered portions for checking do not go beyond the screen. Press the TEST button to proceed to the next page.

Each time the SERVICE button is pressed, the above color bar screen (1/2) and checkered screen (2/2) alternate. Press the TEST button to have MENU return to the screen.

Page 14

@ INPUT TEST

This test displays the state of the START button, COIN SW, TEST button, SERVICE button, etc., which are used in common for each game. Depending on the contents of Cabinet setting, the screen display varies somewhat (refer to examples below). If the switch/button goes ON (from OFF) when activated, it is satisfactory.

EXAMPLE 1) CABINET TYPE 2 GAME SELECT NO COIN CHUTE TYPE COMMON | - ineur test

ap | IP

|STARTOFFOFF

COIN CHUTE #1-OFF #2-OFF

TEST-OFF SERVICE-OFF

PRESS TEST BUTTON TO EXIT

EXAMPLE 2) CABINET TYPE 4P GAME SELECT YES COIN CHUTE TYPE INDIVIDUAL | “oiwpur test

|IP2PSP4P
|STARTOFFOFFOFFOFF
|COINOFFOFFOFFOFF

reST-OFF SERVICE-OFF

SELECT-OFF

Note that the INPUT TEST except for START (Joystick, push button, etc.) should be performed in the EACH GAME TEST mode.

Press the TEST button to have the MENU return to the screen.

Page 15

@® CLOCK ADJUSTMENT

This allows for setting the date (day/month/year) and time on the Main Board.

CLOCK ADJUSTMENTS

01/1 AN/1885 (SUN) <— On-BD present time 29:58:58

28/FEB/1 005 (TUE) <— Time set by the user 10:00:00

<— Applies the time set, by. the ser uber £6 oheeh present Yimes => EXIT <— Return to MENU mode

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

  • Each time the SERVICE button is pressed, the setting position moves sequentially in order of TIME set by the user (day/month/year/day of the week/hour/ minute), SET and EXIT. Second is fixed at 00. Press the TEST button at the desired position to set the time.
  • _ Bring the arrow to SET and press the TEST button to apply the time set by the user to the On-BD present time.
  • After the time setting is finished, bring the arrow to EXIT and press the TEST button to have the MENU mode return to the screen.

28 / FEB / 1995 (TUE) day month year ( day of week)

10 : 00 : 00 H M §&

Note that when setting the date, it is possible to set Feb. 30 or Feb. 31. In these cases, however, accurate functioning would not be maintained thereafter. Therefore, be very careful of this point.

—1Wi-

Page 16

© SYSTEM ASSIGNMENTS

In this mode, various cabinet and board settings can be changed. Game settings such as difficulty levels, etc. are performed in EACH GAME TEST.

  • _ Press the SERVICE button to move the arrow "- >" and bring it to the desired item.
  • Press the TEST button to change the setting.
  • After the setting is finished, bring " - >" to EXIT and press the TEST button.

—_ SYSTEM ASSIGNMENTS — SYSTEM ASSIGNMENTS

CABINET TYPE 2P CABINET TYPE 2P SELECT AUTTON No

ADVERTISE SELECT on GAME SELECT TIME 10 (SEC) ST-V 1L0Go OFF

ADVERTISE SOUND on ADVERTISE SOUND on ALONE/MULTI MULTI ALONE/MULTI ALONE -> EXIT -> EXIT

SELECT WITH SERVICE BUTTON SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON AND PRESS TEST BUTTON FIG.4-5A (MULTI-CARTRIDGE mode) FIG.4-5B (STAND ALONE mode) _ (A) CABINET TYPE (iP, 2P, 3P, 4P) Set to the applicable one from the 4 types.

(B) SELECT BUTTON (NO, YES)

Set to YES or NO depending on whether the cabinet has the SELECT button.

YES «+ Set to this if the cabinet has the SELECT button. For wiring, refer to Section 2, SPECIFICATIONS © CONTROL PANEL AND I/O NO « Set to this if the cabinet does not have the SELECT button. Buttons on the CONTROL PANEL (except for the Start button) can be utilized in lieu of the SELECT button.

(C) ADVERTISE SELECT (ON, OFF)

Determines whether ADVERTISE (during advertise) can be skipped with the SELECT button.

ON «> Set to this when skipping ADVERTISE (during advertise) to proceed to a desired game. OFF «+ The game is selected when credits to start are available.

(D) GAME SELECT TIME (NO, 10 [SEC], 20 [SEC], NO LIMIT)

This determines the time to choose a game once credits to start are available.

NOs When credits to start are available, he game advertised during ADVERTISE is automatically selected.

NOLIMIT «+ When set to this, there will be NO SELECT TIME LIMIT.

(E) ST-V LOGO (ON, OFF)

This determines whether the ST-V LOGO is displayed or not during ADVERTISE in the Multi-Cartridge mode. —12—

Page 17

(F) ADVERTISE SOUND (ON, OFF)

Determines whether ADVERTISE SOUND is to be emitted or not.

(G) ALONE/ MULTI (ALONE, MULTI)

This allows STAND ALONE (ALONE) mode or MULTI-CARTRIDGE (MULTI) mode to be set. In the STAND ALONE mode, items regarding MULTI-CARTRIDGE mode are not displayed (refer to FIGs. . 4-SA and 4-5B in the preceding page).

CAUTION 1: Depending on the contents of SYSTEM ASSIGNMENTS settings, the game may not start up. Refer to the applicable game manual. For example, in the GOLDEN AXE THE DUEL, when the cabinet is set to other than 2P, the game is not ready for play even if tests in the test mode are finished, with CAUTIONS being displayed. Be sure to reenter the TEST mode and correct the contents of the settings.
CAUTION 2: Changing the contents of (A) CABINET TYPE or (G) ALONE/MULTI results in clearing the contents of SYSTEM BOOKKEEPING and the BOOKKEEPING of each game.
Page 18

COIN ASSIGNMENTS

In this mode, the setting of credit increments, etc., as against coin insertion can be changed.

  • Press the SERVICE button to bring the "- >" to the desired item.
  • Press the TEST button to change the setting.
  • After the desired setting is finished, bring the "- >" to EXIT and press the TEST button.
CAUTION: Changing the contents of COIN ASSIGNMENTS settings results in clearing the contents of SYSTEM BOOKKEEPING and the BOOKKEEPING of each game.

COIN ASSIGNMENTS COIN ASSIGNMENTS

COIN CHUTE TYPE COMMON COIN CHUTE TYPE INDIVIDUAL CREDIT TO START 1 CREDIT CREDIT TO START 1 CREDIT COIN/CREDIT SETTING #1 COIN/CREDIT SETTING #1 COIN CHUTR #1 1 COIN 1 CREDIT COIN CHUTE #1 1 COIN 1 CREDIT

COIN CHUTE #2 1 COIN 1 CREDIT

MANUAL SETTING MANUAL SETTING ->EXIT ->EXIT SELECT WITH SERVICE BUTTON SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON _ AND PRESS TEST BUTTON FIG.4-64 (COMMON) FIG.4-68 (INDI VIDUAL)

(A) COIN CHUTE TYPE (COMMON, INDIVIDUAL)

Set this in accordance with Cabinet Coin Chute Specifications.

COMMON Used for the type of the cabinet whose coin acceptance is a common type for plural players. Regardless of the number of players, COIN 1 / COIN 2 ports are used. INDIVIDUAL Used for the type of the cabinet which has a coin acceptance chute for each player. For the COIN SW pont, refer to Section 2 SPECIFICATIONS, @® CONTROL PANEL AND BOARD //O.

(B) CREDIT TO START (1 CREDIT, 2 CREDITS)

Sets the number of credits required when starting the game (1 CREDIT, 2 CREDITS). (Note that in both settings, the number of credits required for CONTINUE is one).

(C) COIN/CREDIT SETTING (#1 ~ #26)

Sets the CREDIT increase increment per coin insertion. There are 26 settings from #1 to #26, expressed in OO credit as against OO COINS inserted. #26 refers to FREE PLAY. For details, refer to Table 1 (COMMON) and Table 2 INDIVIDUAL.

Page 19

@)

033)

(F)

(G) MANUAL SETTING

The CREDIT's incremental increase settings as against a coin insertion are shown in further details than in (C) above (refer to Table 3). Also, note that when this MANUAL setting is performed, the COIN/CREDIT setting becomes ineffective.

MANUAL SETTING SCREEN

COIN ASSIGNMENTS

MANUAL SETTING

COIN TO CREDIT 1 COIN 3 CREDIT

BONUS ADDER NO BONUS ADDER

COIN CHUTE #1 MULTIPLIER N col 1 COIN COUNTS AS 1 COIN

128456678B8
1845678B

CREDIT

COIN CHUTE #2 MULTIPLIER COIN 1 COIN COUNTS AS 1 COIN

12845a28
1284656678@

CREDIT.

->EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON COIN ASSIGNMENTS

MANUAL SETTING

COIN TO CREDIT 1 COIN 1 CREDIT

BONUS ADDER NO BONUS ADDER

COIN CHUTE #1 MULTIPLIER N 1 COIN COUNTS AS 1 COIN 4 6 6 7 8 28 7 8 8 cor 1 2 8 4 5 6 CREDIT

->EXIT.

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON FIG. 4-66 (COMMON)

COIN TO CREDIT

Determines COIN/CREDIT setting.

BONUS ADDER FIG.4-60 (INDIVIDUAL)

This sets how many COINs should be inserted to obtain one SERVICE COIN.

COIN CHUTE #1 / #2 MULTIPLIER

This sets how many tokens one COIN represents.

Page 20

Table 1? COIN/CREDIT SETTING (COIN CHUTE COMMON TYPE) NAME OF SETTING | COIN CHUTE 1 |COIN CHUTE 2

SETTING #1 | 1 COIN1 CREDIT | 1 COIN1 CREDIT
SETTING #2 | 1 COIN1 CREDIT | 1 COIN2 CREDITS
~SETT1 COIN1 CREDIT[1 COIN3 CREDITS
SETTING #4 | 1 COIN1 CREDIT | 1 COIN4 CREDITS
‘SEE1 COIN1 CREDIT | 1 COIN5 CREDITS
| SE1 COIN2 CREDITS | 1 COIN2 CREDITS
| SETTI1 COIN2 CREDITS | 1 COIN5 CREDITS
SEV1 COIN3 CREDITS | 1 COIN3 CREDITS
SET‘|1 COIN4 CREDITS | 1 COIN4 CREDITS
SETTING #10] 1 COIN5 CREDITS | 1 COIN5 CREDITS
| SETTING #11 | 1 COIN6 CREDITS | 1 COIN6 CREDITS |

[SETTING #12 2 COINS 1 CREDIT | 2 COINS 1 CREDIT SETTING #138 2 COINS 1 CREDIT | 1 COIN 1 CREDIT SETTING #142 COINS 1 CREDIT | 1 COIN 2 CREDITS

(SETTING #15 / 1 COIN1 CREDIT|1 COIN1 CREDIT

a | 2 COINS 8 CREDITS | 2 COINS 3 CREDITS

SETTING #16) 1 COIN1 CREDIT | 1 COIN8 CREDITS

_ | 2 COINS 8 CREDITS SETTING #17 | 3 COINS 1 CREDIT | 38 COINS 1 CREDIT SETTING #18 | 4 COINS 1 CREDIT | 4 COINS 1 CREDIT

SEITING #19] 1 COIN1 CREDIT | 1 COIN1 CREDIT

2 COINS 2 CREDITS | 2 COINS 2 CREDITS 3 COINS 8 CREDITS | 8 COINS 3 CREDITS I 7 4 COINS 5 CREDITS | 4 COINS 5 CREDITS

| SETTING #201 COIN1 CREDIT | 1 COIN5 CREDITS

| 2 COINS 2 CREDITS | 3 COINS 3 CREDITS | 4 COINS 5 CREDITS SETTING #21 | 8 COINS 1 CREDIT | 1 COIN 2 CREDITS 5 COINS 2 CREDITS SETTING #22] 2 COINS 1 CREDIT | 2 COINS 1 CREDIT | 4 COINS 2 CREDITS | 4 COINS 2 CREDITS _ __| 5 COINS 8 CREDITS | 5 COINS 3 CREDITS SETTING #23] 2 COINS 1 CREDIT | 1 COIN 3 CREDITS 4 COINS 2 CREDITS 5 COINS 8 CREDITS

| SETTING #24/1 COIN1 CREDIT|1 COIN1 CREDIT

| 2 COINS 2 CREDITS | 2 COINS 2 CREDITS | 3 COINS 3 CREDITS | 3 COINS 3 CREDITS 4 COINS 4 CREDITS | 4 COINS 4 CREDITS : 5 COINS 6 CREDITS | 5 COINS 6 CREDITS

SETTING #25 | 1 COIN1 CREDIT | 1 COIN6 CREDITS

| 2 COINS 2 CREDITS 8 COINS 3 CREDITS 4 COINS 4 CREDITS | 5 COINS 6 CREDITS _ SETTING #26[ FREE PLAY FREE PLAY

Page 21

Table 2: COIN/CREDIT SETTING (COIN CHUTE INDIVIDUAL TYPE)

[NAME OF SETTING | EACH STATION’S COIN CHUTE [NAME OF SETTING | BACH STATION’S COIN CHUTE SETTING #1 1 COIN 1 CREDIT | SETTING #21] 3 COINS 1 CREDIT

SETTING #6 | 1 COIN2 CREDITS| 5 COINS 2 CREDITS

SETTING #8 | 1 COIN 3 CREDITS SETTING #22] 2 COINS 1 CREDIT

[SETTING #9 |1 COIN4 CREDITS4 COINS 2 CREDITS
| SETTING #10) 15 CREDITS |5 COINS 3 CREDITS

| SEITING #11 | 1 COIN 6 CREDITS | SETTING #24) 1 COIN 1 CREDIT

SETTING #122 COINS 1 CREDIT2 COINS 2 CREDITS
SETTING #151 COIN1 CREDIT8 COINS 3 CREDITS

_ | 2 COINS 8 CREDITS A COINS 4 CREDITS [SETTING #17 8 COINS 1 CREDIT 5 COINS 6 CREDITS SETTING #18 | 4 COINS 1 CREDIT SETTING #26 FREE PLAY _

“SETTING #191 COIN1 CREDIT

| 2 COINS 2 CREDITS | 3 COINS 3 CREDITS (A OOINS 5 CREDITS

Table 3 > MANUAL SETTING

‘COIN TO CREDIT 1 COIN 1 CREDIT 2 COINS 1 CREDIT | 3 COINS 1 CREDIT | 4 COINS 1 CREDIT 5 COINS 1 CREDIT 6 COINS 1 CREDIT 7 COINS 1 CREDIT 8 COINS 1 CREDIT 9 COINS 1 CREDIT

[BONUS ADDER NO BONUS ADDER 2 COINS GIVE 1 EXTRA COIN 3 COINS GIVE 1 EXTRA COIN | 4 COINS GIVE 1 EXTRA COIN | 5 COINS GIVE 1 EXTRA COIN 6 COINS GIVE 1 EXTRA COIN 7 COINS GIVE 1 EXTRA COIN 8 COINS GIVE 1 EXTRA COIN | - - 9 COINS GIVE 1 EXTRA COIN

[COIN CHUTE #i/7#2 1 COIN COUNTS AS 1 COIN

MULTIPLIER [1 COIN COUNTS AS 2 COINS

| [1 COIN COUNTS AS 3 COINS 1 COIN COUNTS AS 4 COINS 1 COIN COUNTS AS 5 COINS | 1 COIN COUNTS AS 6 COINS 1 COIN COUNTS AS 7 COINS 1 COIN COUNTS AS 8 COINS 1 COIN COUNTS AS 9 COINS

Page 22

@ SYSTEM BOOKKEEPING

Allows for checking data such as number of coins inserted / number of credits / time / game frequency.

COIN CHUTE #1 COIN CHUTE #2 COIN CHUTE #3 COIN CHUTE #4 TOTAL COINS

COIN CREDITS SERVICE CREDITS i SYSTEM BOOKKEEPING

TOTAL CREDITS 200 ccc0e

NUMBER OF GAMES °

GAME PLAY TIME ODO0OHOOMOOS

SERVICE BUTTON TO OTHER PAGE | TOTAL TIME oD00HOOMOOS i { TEST AUTTON TO RETURN

(% 1) COIN CHUTE #1, #2, (#3, #4 PAGE 1/2

) =

Depending on Cabinet Type setting and Coin Chute setting, the number of display items and meanings are different.

When the Coin Chute Type is COMMO! Regardless of the Cabinet Type setting, Items #1 / #2 are displayed. Displays the number of coins inserted per COIN 1 and COIN 2 are displayed.

When the Coin Chute Type is INDIVIDUAL: Depending on the Cabinet Type setting (1P ~ 4P), the number of items vary. Each value for #1 ~ #4 represents the number of coins inserted by the corresponding 1P ~ 4P Players.

SYSTEM BOOKKEEPING

CART#1 (GOLDEN AXE DUEL } CART#2 N AXE DUEL J CART#3 AXE DUEL } 5} EARTH’ [GOLDEN AXE DUEL

CART#! CART#2 CART#S C.

NUMBER OF GAMES NEW GAME CONT GAME ° 0 0 0 TOTAL GAME 0 0 )

GAME TIME.

AVERAGE0M00SO0MO00SOMOOS
LONGEST0MOOSOMOOSOMOOS
SHORTEST0MO00SOMO0SOMOOS

SERVICE BUTTON TO OTHER PAGE TEST BUTTON TO RETURN PAGE2/2

ART#A

omoos oMOOS oMoos SYSTEM BOOKKEEPING PAGE2/2

NUMBER OF GAMES NEW GAME ° CONT GAME 0 TOTAL GAME 0

GAME TIME AVERAGE omMoos LONGEST omMoos. SHORTEST omMoos

SERVICE BUTTON TO OTHER PAGE TEST BUTTON TO RETURN (MULTI-CARTRIDGE mode) (STAND ALONE mode)

The display on page 2/2 varies depending on the cartridge mode.

Press the SERVICE button to alternate page 1/2 and 2/2. Press the TEST button to have the MENU mode return to the screen.

Page 23

BACKUP DATA CLEAR

Clears the contents of BOOKKEEPING.

BACKUP DATA CLEAR

SYSTEM DATA CLEAR

ALL DATA CLEAR

-> NO CLEAR (CANCEL)

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Press the SERVICE button to bring the "- >" to the desired item and press the TEST button to execute the desired item as follows:

(A) SYSTEM DATA CLEAR Clears the contents of SYSTEM BOOKKEEPING.

(B) ALLDATA CLEAR Clears each game's BOOKKEEPNG in addition to clearing the SYSTEM BOOKKEEPING.

(C) NO CLEAR (CANCEL) This does not execute clearing and causes the MENU mode to return on the screen.

_ALL_ DATA CLEAR

BACKUP DATA CLEAR

SYSTEM DATA CLEAR

-> ALL DATA CLEAR

NO CLEAR (CANCEL)

SYSTEM BACKUP DATA AREA CLEAR GAME1 BACKUP DATA AREA CLEAR GAME2 BACKUP DATA AREA CLEAR GAMES BACKUP DATA AREA CLEAR GAME4 BACKUP DATA AREA CLEAR COMPLETED

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

CAUTION: Apart from the above, the contents of BOOKKEEPING can be cleared as in (B) ALL DATA CLEAR above by changing the setting of CABINET TYPE or ALONE / MULTI of ® SYSTEM ASSIGNMENTS, or the setting of © COIN ASSIGNMENTS.
Page 24

® EACH GAME TEST

This allows for entering the TEST mode of each game which is connected to a Cartridge Slot. The TEST MENU includes each game's INPUT TEST (Control Panel), GAME ASSIGNMENTS including Game Difficulty, BOOKKEEPING, etc. Depending on games, there are some increases/decreases as regards the necessary / unnecessary items, and also the contents vary. For details, refer to the specific Instruction Manual of each game.

EXAMPLE: MENU SCREEN, GOLDEN AXE THE DUEL

TEST MENU

| INPUT TEST i SOUND TEST

GAME ASSIGNMENTS

BOOKKEEPING

BACKUP DATA CLEAR

-> EXIT

SELECT BY SERVICE BUTTON AND PRESS TEST BUTTON

Page 25

B) FACTORY TEST MODE

This mode is intended for the development of games which employ the STV-Board, and for Factory Hardware-Check. Unless instructions are specifically given in an applicable Manual elsewhere, do not use this mode. When so required, however, enter the mode by turning the power on while keeping the TEST button pressed down. If the mode is used without specific instructions, normal operation can not be guaranteed. (During test, the COIN METER may suddenly function sometimes.)

BOOTROM verl. 108 ST-V TEST MENU (in Factory)

-> CONTINUOUS HARDWARE TEST

|MEMORYCHECK

c. R. T. CHECK VDPI/VDP2 CHECK 1/0 (10GA) CHECK 170 (SMPC) CHECK SOUND CHECK EEPROM CHECK DUAL-CPU CHECK CLK-CHANGE CHECK

SIMM CHECK

|RS-282CCHECK
|scsi-2CHECK

SYSTEM CONFIGURATION

IF YOU WANT TO EXIT, PLEASE POWER ON AGAIN.

SYSTEM CONFIGURATION

This allows for environmental setting at the development stage. For initialization, refer to the following:

SYSTEM CONFIGULATION

DEVELOP-MODE NO scsi-ID 0 SIMM-ALLOCATE CART-AREA scsi UNUSE SCSI-BOOT NON-BOOT HOST-TYPE Pc ST-V LOGO OFF ALONE/MULTI ALONE

=> EXIT

SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON

Page 26
  • WIRING FOR THE BOARD

A) 2-PLAYER SIMULTANEOUS PLAY, 6-BUTTON SPECIFICATIONS (2L12B)

WIRE HARNESS used: WIRE HARN ST-V EXT8B (PART No. 600-6558-05)

The GND wire of this WIRE HARNESS is black, so be careful of this point. SW | ~ 3 correspond to JAMMA Connector. Wire SW4, SWS and SW6. No wiring is required for yellow and gray wires which come from Pin Nos. 6 & 10.

PLAYER 1 PLAYER 2 2L12B O1P START © 2P START CONTROL PANEL 214 Q@® 214 OQ® WIRE HARNESS “1s @@G 71 O9@

eupy«606 00-6558-05aa
{1}BLACKGND:'''‘'
2 |BLACKPibit
3 |PINK1P_ Sw4atswthad
rq[SKY BLUEo1P_SwsionaDit
[Ss |QRANGE_1P_SW65-3.:'
6LIGHT GREEN-:'
7BROWN2P SW4soe'
TQ |PURPLE2P_SWSao‘
i)BLUE52P_ SWECa

70 GRAY _ _

71BLACKGND

JST 11P

Page 27

B) 3-4 PLAYER SIMULTANEOUS PLAY, 3-BUTTON SPECIFICATIONS (3L9B,4L12B)

WIRE HARNESS used: 3 PLAYER; WIRE HARN ST-V EXT3P (PART No. 600-6558-07)

4 PLAYER; WIRE HARN ST-V EXT 8B (PART No. 600-6558-05)

The GND wire of this WIRE HARNESS is black, so be careful of this point. 1P and 2P correspond to JAMMA Connector. Wire for 3P and 4P

PLAYER 1 PLAYER 2 PLAYER 3 PLAYER 4

Con TeorPANELa START0 START a sree Ke ad

WS O@® ie O@® aS ooo ite 009!

ST-V.WIREHARNESS'
CN32600-6558-07'
7 LPLNK/WH ITE3P_SW1sts.‘
2LSKY BLUE/WHITEBPSW2ahs:
3PORANGE/WHITE3P_SW3ats‘
4HT _GREEN/WH| TE——o-3P_START55'
T}BROWN/WHITE_ae3P_ DOWN5»efeneeee 3
&PPURPLE/WHITE_3P_UPon
7BLUE/WHITEo 3P_ RIGHT5—~p
@LGRAY/WHITE>BP_LEFT6

iS) | BLACK _ GND JST 9P

ST-V WIRE HARNESS CN21 600-6558-05 BLACK BLACK =

PINK4P_SW1on
SKY BLUE9 4P_SW2ats
ORANGE4P_SWw3ats
LIGHT GREEN_o 4P_ START545
BROWN_o 4P_DOWN5,ebenene nee
PURPLE4p uPono
gBLUEo4P RIGHT5»
imGRAY9 4P LEFTSy ’
71BLACKGND
Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 30

SEGA ENTERPRISES, LTD. 13-1, Higashikohjiya 2-Chome, Ohta-ku, Tokyo, Japan 144 OTel. : (03) 5736-7721 OFAX : (03) 5736-7729 OTLX : J22357 SEGASTAR

© SEGA 1995

Printed in Japan