CATHODE RAY TOMES

Digger

Digger (Sega, 1980) · Manual · 62 pages · 53 sections · original scan

Page 1

Owner’s Manual

Page 2

DIGGER

Operating Instructions

and

Service Manual

Copyright * 1980 by GREMLIN/SEGA INDUSTRIES, INC. All rights reserved.

Page 3

INTRODUCTION...

This is an electronic game that makes extensive use of digital integrated Circuitry and television monitor circuitry. This manual assumes the maintenance technician possesses a general knowledge of solid state circuitry microprocessor, TTL digital integrated circuitry and TV. monitor concepts. Any individual not knowledgeable in these areas should not attempt repair of the electronic portion of this game. It should be noted that any attempt to repair the game in the field without the express consent of the factory will immediately void the warranty!!!

IMPORTANT NOTES... An important service note is posted in this game and is repeated here for emphasis:

If at any time the TV. screen shows a meaningless display or the game otherwise malfunctions, simply drop a Coin into the coin mechanism. This should correct the problem. If ‘not, the game requires service.

The circuitry in this game has been arranged so that the insertion of a quarter through the coin mechanism will reset the restart in the system. This clears up temporary problems caused by power line disturbances, static, etc.

SERVICE TECHNICIAN NOTE:

The system reset circuitry described above requires that the coin counter is attached to the system. If there is a coin counter problem and no replacement is available, the game will function properly if a 10K Ohm resistor is connected across the coin counter input pins to the video logic board.

ALSO... Never replace any components with anything other than exact replacement parts. (See Parts List located on Service Schematics.)

Never remove circuit boards/connections while power is on.

Do Not replace the fuse with anything other than the proper value. A blown fuse indicates an overload condition within the game. Replacing the fuse with a higher value can cause severe damage to internal components if an overload occurs.

Always consult the manual before attempting repairs.

Correspondence regarding this game should be addressed to:

Gremlin/seca 8401 Aero Drive San Diego, California 92123 (714) 277-8700

Page 4

REPACKAGING INSTRUCTIONS...

Arcade 254° Wx 07° Hx 28D 4.7 7em W x 170,18em H x 711m D 290 tbe. /132 kg

Arcade Version rT i ae

  • Carefully lay game on its side. co
  • Attach pallet with four 5/16” - 18 x 1-3/4” bolts, as shown. TT ‘
  • See Final Recrating Instructions, below.

22H x 21" Wx 20"D Mini-Video Version Sten He S83hem W x Sem D

  • Place game upright inside bottom cover. J —
  • Slide cover over game. Add protective packing material.
  • Place top cover over side cover.
  • See Final Recrating Instructions, below. ‘ail

Cocktail Version wate iH

1. Place game inside carton. aaa lee

  • Add protective packing material.
  • Place inside protective top cover over unit. .
  • Close flaps and secure with shipping tape. |
  • See Final Recrating Instructions, below.

FINAL RECRATING INSTRUCTIONS...

Place game upright. Tape down game keys. Then, crate the game using appropriate shock-absorbent packing material. Include packing on edges of game. Secure package with strapping.

Note ... If the game is to be shipped to Gremlin Industries for service or repair, attach a tag identifying the distributor and indicate the service or repair to be done. Include the full serial number of the game.

All items must be shipped prepaid.

Page 5

GAME CONCEPT...

DIGGER is a new Gremlin/SEGA game that requires you to dig strategically placed holes within a maze format so you can capture and fill in over the invading creatures before they can attack and destroy your man. You maneuver your man around the maze with a four-directional joystick. Two push-button controls are used for your shoveling action: one, for the DIG function and another for the FILL function. The maze format changes with every round played. DIGGER is a Gremlin Multi-Phaset™ game that becomes increasingly challenging as your skills improve, as you will see. The creatures are confined behind a wall. In the first of three rounds of game play, four creatures are let out of the holding area through a gate. You must conquer these four before advancing to the next round, where you face six creatures. Your third round has you battling eight creatures. This process is repeated and the point value increased with each three-round victory. Also, the creatures! speed increases each round, Any contact at all with the creatures will be fatal to your man. While you are busy digging holes and entrapping creatures, the rest are behind the retaining wall scurrying back and forth. After about three minutes, the gates at each end will open and all ofthe remaining creatures will stream into the play area at once. However, a skillful player will conquer all of the creatures of each round and the gate will not be a threat. A DOUBLE SCORE BONUS is awarded if you capture and fill in over the RED creature before any of the GREEEN ones. But, this must be the FIRST creature defeated, or the RED creature becomes GREEN and no bonus is awarded, The point value per creature increases with each three-round phase. The first phase awards 300 points per creature, decreasing to 100 points if not filled over promptly. The second phase awards 500 points per creature, decreasing to 300. And, the third phase awards 700 points, decreasing to 500 points. A 1000 POINT BONUS is given if you capture four creatures in a row at full point value during any one round. An EXTRA MAN is given at 5000 points. When a creature is captured, eight squeaking sounds are heard before the creature escapes from the hole. Five squeaks are required to cover a creature, so you must hurry to the hole and FILL before the fourth squeak, or the creature will emerge and devour your man. 'f your FILL is incomplete and another creature passes along the same path, it will pull the other out and your man may be eaten. If a hole is incomplete, it will delay creatures somewhat, depending on the size of the partially dug hole. On the DIGGER upright and Mini-Video games, two players alternate turns. A player loses his turn when the round is complete, not just when he loses a man. On the slimline and cocktail tables, DIGGER can be a two-player SIMULTANEOUS PLAY, or ALTERNATE PLAY, as described above. In the SIMULTANEOUS PLAY option, the sum of Player 1 and Player 2 scores are used as one final score. The game play is the same as one-player and either man may FILL a hole, regardless which one dug it. If you select ALTERNATE PLAY action, it is the same as the upright or Mini-Video. A unique feature of Gremlin/SEGA's DIGGER game is the personalization of HI SCORES. At the end of the game in which the highest score of the machine is topped, the player uses the DIG and FILL buttons to run through the alphabet selecting his three initials. These will remain until that score is topped by another player. In SIMULTANEOUS PLAY, Player 1 enters his initials first, and then Player 2 enters his. Both initials are displayed until their score is beat.

Page 6

DIGGER SOUNDS

BACKGROUND SOUND is used anytime creatures are present in the maze. This sound speeds up with the creatures' speed. An ESCAPE SOUND is used as the creatures rush through the gate into the maze area. A DOUBLE BONUS SOUND is used when the red creature is the first captured. Another BONUS SOUND is heard when the 1000 POINT BONUS is awarded. A beeping CREATURE SOUND that squeaks when a creature falls into a hole. A SCORING SOUND accompanies the flashing score display after a creature is buried. A SCREECH SOUND is used when your man is eaten by a creature. A RELEASE SOUND is used when a creature leaves a hole. A GAME-OVER BOOM is heard at the end of the game.

OPTIONS SELECT...

DIP SWITCH # i 2 No. of Men

offoff3
UPRIGHTonoff4
offon5
onon6

DIP SWITCH # 1 2 No. of Men

offoff5
COCKTAILonoff4
offon3
onon2
Page 7

NEW GAME BOARDS

AND NEW EPROMS...

Fhe following chart shows the two kinds of logic boards Gremlin will use in future games. These will be either a SINGLE VIC board or a DUAL VIC board. Also shown are the possible combinations of Eprom types that Gremlin will be using. The 2 Eprom types are:

  • 2708 (holds 8K of memory)
  • 2716 (holds 16K of memory).

Obviously, the 2716 holds twice as much information as the 2708, but the 2 Eproms are not directly compatible—in other words, you have to replace a 2716

with another 2716, and a 2708 with another 2708. In aaaition. the 2716 Eprom

socket is modified slightly to accept the 2716 Eprom. If it is ever necessary to replace a new Eprom, be sure to specify 2708 or 2716 . These numbers are printed on the Eprom package.

Logic Board Type | Possible Eprom Types Used , Where Used SINGLE VIC board | 1) All 2708’s HEAD-ON 1 HEAD-ON 2 Future games

  • 2708's and one 2716 INVINCO. (used in combination) DEEP SCAN Future games

The two Eprom types are used since some game programs require a larger memory than that provided with a set of 2708's. Usually, one 2716 provides enough additional memory space to hold a longer program.

Page 8

POWER SUPPLY MODIFICATIONS... For VIC Logic Boards Only In order to supply — 5 volts to the VIC logic board, it was necessary to modify the game power supply. The modification simply adds a 7905 —5 volt regulator (Gremlin part #313-0023) to the power supply chassis; the 7905 is connected into the — 12 volt line at pin 11 of the power supply output connector. PIN 17 OF THIS CONNECTOR NOW BECOMES THE -§5 VOLT OUTPUT. The other pins remain the same: pin 11 = —12v pin 12 = +12v pin 13 = 2-3 V AC signal pins 14, 15, 16 = GROUND pin 17 = -—5v pins 18, 19,20 = +5v

Also, a 8900 ufd filter capacitor has been added to the power supply to provide better + 12 volt regulatiog. .

TRANSFORMER VOLTAGE

CONVERSION INSTRUCTIONS...

To convert the game transformer to 100, 115, or 230 VAC, refer to the following chart:

*For 100 volts: Connect the voltage INPUT lines to transformer terminals 1and2._

*For 115 volts: Connect the voltage INPUT lines to transformer terminals 1 and 3.

*For 230 volts: Connect the voltage INPUT lines to transformer terminals 1 and 4. The fluorescent lamp line must be connected to transformer terminal 3.

ALSO, THE TV MONITOR MUST BE CONVERTED TO THE SAME VOLTAGE INPUT AS THE GAME TRANSFORMER. REFER TO THE MONITOR MANUAL IN THE GAME.

Page 9

MAINTENANCE PROCEDURES

SINGLE games

Power Supply (Refer to drawing #800-0072, sheet 4)

  • Remove output connectors from power supply. 2 Make these initial tests: (GND to BLACK lead on C18, 9000 ufd capacitor)

a. b. c. d. —7TO nO +9 VDC on POSITIVE terminal of C18 +17-19 V on C6 (4700 ufd cap.) -17-19 Von C5 (4700 ufd cap.) -12 V at output pin 11 (adjustable by trim pot R42) . +12 V at output pin 12 (adjustable by trim pot R8) . +5 V at output pins 18,19,20 (adjustable by trim pot R9) GND (ground, 0 V) at pins 14,15,16 2-3 V AC at pin 13 (Don't forget to change meter scale to AC) + 75 Vat pin 17

  • Check these voltages again with the logic board connected. !f any are wrong, a loading condition exists in the logic board, most likely.

Logic Board The following instructions will help you trace down and find most problems associated with the logic board. The procedures are listed by the more common kinds of problems that could arise. Read through all the steps first, then apply them one at a time. The necessary equipment are an oscilloscope and AC/DC voltmeter.

  • NO PICTURE; IV TUBE AND FLUORESCENT LAMP ARE OFF

a. Plug the game in and check to see that it is receiving 115 (230) VAC. Measure 115 VAC at the input terminals of the game transformer. If it is not present here, proceed to next step.

. Check the fuse; if it is good, proceed to next step.

  • Remove the cover of the junction box in back of the game. Measure 115 VAC on the output of the line filter. If it is not present, the line filter may be bad. Or, one of the AC line connections in the junction box may be loose. UNPLUG the game and re-check these connections.

If the fluorescent lamp still does not operate, turn off game and on again. This usually re-starts the lamp. If it doesn't, turn the lamp in its socket; this will re-seat it for a better connection. Sometimes the lamp works loose during shipment.

. An ON/OFF switch for the TV monitor is located en the TV chassis, below the neck of the picture tube. Make sure it is ON.

2._NO PICTURE: IV IUBE AND FLUORESCENT LAMP ARE ON. SCREEN BLACK. a. First, make a quick check of the monitor-to-logic board connections: Are all wires making contact with the pin connector? Are the wires secure on the monitor plug-in connector?

Page 10

b. Check to be sure U65 is seated in its socket properly, and that no pins are bent. This IC is a Prom that develops the necessary video timing sequences. Usually, if one pin on the chip is out of the circuit, the screen will appear black. Proceed to the next step if this chip is seated correctly.

c. Inspect the high-voltage lead coming off the monitor's high-voltage transformer. This lead attaches directly to the TV tube. Sometimes, during shipment, this wire is jostled out of contact with the transformer. Turn off the game, and carefully push the wire down toward the transformer to reseat it. Now, check to see if the picture comes on. If it doesn't, proceed to step d.

d. Using a voltmeter, measure the three voltages powering the logic board. These voltages are: +5v, -5v, +12v, and can be easily measured at the power supply-to-logic board connection. If all voltages are present, go to the next step.

e. Using an oscilloscope, test for clock signals at the points listed below. For the moment, don't worry about what each signal should look like. We're’concerned with finding floating signals, and/or signals that are not present when they should be...and why they are not. The scope setting is .2v/div. @ 5usec with a 10:1 probe. ATI clock signals, except the video signal, are about 5 volts in amplitude.

  • Check pins 8, 11 of U41. Look for a 14 volt video signal. {f not there, check pin 12 of U41. If it is there, U41 is probably bad.
  • If the signal is not at pin 12 of U41, suspect U48, U42 and U32.
  • Check the following IC's and pins for any floating, or missing signals: U68 pin 6 U65 pins 1-7,9 U67 pin 5 U4Q pins 2,6,10,15 U60 pins 11,12,13,14 U5O pins 2,7,10,14,15. These chips make up thevideo timing circuit. Make sure there are no floating, or missing, signals on any of these chips. If there are, suspect the chip is bad.
  • PICTURE APPEARS: COLOR IS DISTORTED; SOME COLORS MISSING

Check the red, blue and green output signals on U42, pins 4,7, and 9, respectively. If no signals are present, suspect U67, U49, U43, U4S, u44, U30 or U66.

4, INCOMPLETE PICTURE: RANDOM DISPLAY

Sometimes the game appears on the screen with parts of the picture showing incorrect information. For example, the "H! SCORE" listings display jumbled information, while the rest of the picture is normal. The most likely cause of this problem is one of the 8 RAM IC's US6 through U63. The quickest way to find the bad RAM is simply to replace each IC, one at a time, with aRAM that is known to be good. Be sure not to bend any pins when replacing the IC's. Also, don't overlook the possibility that one of the RAM sockets is bad.

  • RANDOM DISPLAY WHEN GAME IS TURNED ON

a. Activate the coin switch a few times to see if this clears the picture. If not, turn the game off, then on again. If the jumbled display stil} appears, proceed to step b.

Page 11

b. Check the reset circuit on the logic board (Refer to the schematic). When power is first applied to the game, a reset circuit consisting of Q10, Q11, USS and U71 is triggered an to reset the microprocessor. This reset signal forces the microprocessor to start at the beginning of the game program. If the microprocessor is not reset, it will still operate...it just won't operate on the right program instructions or data, and will continually display a jumbled pattern on the screen. So, begin by checking for a 3-4 VAC signal at pin 3 of the power supply-tologic board connector. Follow the signal through Q10 where, at the callector, a sawtooth wave appears. Then, when power is first applied, observe pin 2 of U55 as capacitor C20 slowly discharges to about 3 volts. When this level is reached, U55 is triggered to change states, causing pin 3 to go high, then low. This change is inverted by U54 and, finally, reaches pin 26 of the Z80. Check pin 26 of the Z80 for a low-to-high signal change. If not present, one or more of the reset circuit components are bad. If it is present, proceed to step c.

c. The following lists some probable causes of the jumbled display pattern: *one or more RAM's A‘ *one of the Eproms, U1-8, U20-27 “

*the microprocessor, US3, is bad *U33 or U34 (74L$245) is bad *U19 is bad *check the three operating voltages, +5v, -5v and +12v VDC.

  • GAME DOES NOT COIN UP_ a. A common problem with a game that does not coin up is that the coin switch trip wire is out of adjustment. Usually, all that is necessary is to bend the trip wire up or down, depending on whethter a heavier or lighter tension is needed.

b. There may be a problem in the coin circuit on the logic board. Check U2, pins 3,11, for pulses each time the coin switch is tripped. Also, Ull and/or U12 may be bad. Suspect U45, also.

c. It is possible that one of the coin counter transistors, Q1 and Q2, is bad. Determine whether or not the counter advances each time the coin switch is tripped.

d. Don't overlook the possibility of an incorrect, or faulty, coin swi tch-tologic board connection; sometimes, these wires work loose from the coin switches.

  • _PLAYER CONTROLS NOT WORKING

a. Check first to be sure all control switch connections are secure. This includes checking the black wires, or ground leads.

b. If these connections are good, make sure the control panel leads are intact inside the Molex ‘connector to the logic board.

‘c. If the controls still do not work, suspect Ul on the logic board. However, U1 could be good but might not be receiving the activating pulses from U36, pin 13, or U4, pin B

Page 12
  • _GAME SOUNDS NOT HEARD. Check to be sure the sound board output lea@ Is making good contact with the power supply/amplifier connector. Refer to the game wiring schematic.

If these connections are good, check the power supply/amplifier board for any audio signals. Specifically, check U4, QB and Q9 on the amplifier board for any game sounds.

If there are none there, suspect U16 on the logic board. Also, check U32 for the pulses that turn on U16.

If these chips appear good, the sound boards are probably bad. Refer to the sound board schematics for each sound's circuit.

Page 13

RECOMMENDED SPARE PARTS for SINGLE games

GREMLIN WHERE PART NO. USED DESCRIPTION

130-0001aspeaker
130-0002aspeaker cover
200-0014u19" color monitor
200-0015scolor monitor
200-0013c13'' color monitor
253-0104uplexi, front monitor panel
390-0011ufluorescent lamp
220-0035ucoin door lock & key
220-0097scylinder lock,
117-0126scoin entry plate, USA
220-0066ucoin mechanism, complete
800-0103cscoin mechanism, complete
220-0071ucoin reject button & spring
240-0097sreject button assy.
220-0072ucoin return stop (u-bolt)
800-0076aphoto-coin accumulator assy.
270-0008acoin counter

510-0014 slide switch

220-0148scash box

u cash box

601-0546stv mask
601-0032scolor mask
103-0043.ocleg arm
601-0504cleg
104-0005chandle
504-0118csswitch, micro (joystick
109-0032cshandle ball, black
109-0033cshandle ball, red
509-0048csswitch (I-r)
509-0052csswitch (fr/acc)
240-0107épush button, acc.
510-0041uswitch, joystick
510-0023upush button mounting/contacts
240-0009uyellow push button plunger
240-0109uOrange push button plunger
240-0105spushbutton switch
240-0106spush button knob
509-0119spush button, red
800-0056ucomplete joystick
240-0091ujoystick knob
250-0289uthreaded rod
250-0291uupper sleeve
601-0158csswitching regulator
560-0052cpower transformer
560-0053spower transformer
270-0001uline filter, junction box
514-0001afuse, 2A slo

all versions upright cocktail slimline “wocm wow QTY. PER 10_GAMES

Wats BH BwWUNVuUwNuunny HUUwwU sees ee HUN UN NN eee eee

Page 14

600-0001 800-0072 482-0013 482-0014 482-0015 482-0016 313-0001 313-0004 315-0019

315-0050

316-0507 314-0001 314-0093 314-0099 314-0104 314-0105 315-0031 315-0039 315-0042 316-0206 475-0002 482-0010 510-0043 314-0042 481-0006 481-0008 482-0006 482-0023 312-0145 312-0146 312-0069 312-0147 oooKOHHDODD

o

DOOR HDHDHHDHOHHHHDHOHDHHOHOD ac power cord dual power supply xstr TIP.110 . 2N4401 xstr TIP 115 xstr TIP 29 LM 723 DIP LM 741 DIP 2708 EPROM, .blank oo wash specify number on EPROM 2716 EPROM, blank specify number on EPROM color prom DIGGER 5551C 74 LS 374 IC 74 LS 245 IC 74 LS 138 IC 74 LS 253 IC 280 microprocessor RAM IC video interface chip (VIC) video timing prom resistor pack PE 8050 transistor 6-position DIP switch 7406 IC IN914 diode 1N5231 Zener diode 2N4403 transistor 2N4093 transistor CMOS 4006 IC CMOS 4070 IC LM3900 94560 IC wMuUMeu=

UNBWWWONWWwwL = = set

set

Page 15

TITLE TOP ASSEMBLY

Gremlin/seca | PARTS piccer UPRIGHT 700-0019 |sH I

San Diego, Calfarma 92123 ENGLISH, WHITE DWG NO oF Ss REV

USE WITH 800-3070 FOR [DRAWN MAHONEY

PARTS LOCATIONS. CHECK A. AMBROSE G-2-86 |appR [LTR] DATE | REVISION DESCRIPTION [DRAFT | CHECK | | CHECK | APPR | Pa fo-9- ac] RELEASED are AFA]

TO HEXAGON CALL-OUTS ON DRAWINGS FOR

LOCATION OF PARTS LISTED HERE.

Page 16

PARTS | TITLE TOP ASSEMBLY _ ~ ENGLISH, WHITE DWG NO OF 5 | REV

COTY PER ASSY | PART NO DESCRIPTION 800-3070 ASSY BASIC KIT DIGGER 800-3066 ASSY VIC LOGIC DIGGER ENG 140-0048 CABINET BASIC WHITE 420-0490 GRAPHIC SIDE RIGHT 420-0489 GRAPHIC SIDE LEFT - 800 -0122 ASSY SHIPPING KIT

Page 17

San Diego, Calforma 92123

SHEETS THRU7 IS *D" SIZE

SHT8 IS"C* SIZE. THELE ACSY DIGGER 7O0-O0I5 |SH!

COCKTAIL ENGLISH DWG NO OF 8

IDRAWN SON DUONG ENGR [CHECK A.AmBRose @-9-80 [APPR si REVISION DESCRIPTION | DRAFT | CHECK | APPR | RELEASED psp] AFA [AFA |

Page 18

Gremlin Industries, inc. 420-0370 Parts |TITLE assy DIGGER - COCKTAIL ENGLISH 70070 O15

DESCRIPTION

420-0371 252-0082 560-0051 800-0072 ASSY POWER SUPPLY

800 - 3043 ASSY HARN SOUND DGGER

800- 3033 800 - 0103 834-0010 800 - 30506 800-3044 800- 3045 370 - 0002 BOG - 3049 280-0005 800 - 3051 800-3048 260 - 0064 SPACER 3/e LNG PVC

800 - 3055 ASSY GROUND CABLE

Page 19

me] _rarrno [Srey] bescrerion rem PART NO ~ TTT DESCRIPTION 26 | B00 - 01076 PHTO CN CALC BOARD er feco= eet} TT fa Sea }2i1 = 0045 | 2\t -0042 250 - 0412 B00 - 3064 270 - 000I B00 - 3026 211 - 0038

EMI FILTER

ASSY FUSE BLOCK

CONN QUICK Sig SCREW PHL.PN HD © XI/2 SH MTL

28, | 29 | 40 | | NUT WIRE. SMALL fFIOx 3/e'PN HD

Page 20

PARTS | TITLE ASSY DIGGER

LIST COCKTAIL ENGLISH

QTY PER ASSY

DESCRIPTION

PART NO

B00 - 3086 I ASSY HARNESS SOUND_INVINCO 834 - 0007 | a SOUND BOARD_ INVINCO 700 - OOIS see a DWG NO see a

Page 21

FORM NO. 001-1500

TITLE

ASSEMBLY BASIC

COIN MECH ~ DUAL DRAWN 4m rou Veee. CHECK. “",, -

REVISION DESCRIPTION

Page 22

COCK FORT LOCK IR

QOPTO - (SOL.ATOR § TIL/39

250-0068 420-1046 476-0007 S10- OOl4k

NO Lt q Hi (4 & ! | | LREW, MACH. PU. PHL 4-40x 4"

WASHER, FLAT #6

WASHER, LOCK SHIT #6

4/0-O08!

WASHER, FLAT #4

Page 23

HHILeE ASS Y

PHOTO COIN CALE LTR] DATE REVISION DESCRIPTION

DRAWN (1,006 eee /1- 29-79)

U BUT 4 SARE tee

|FERE@N 366 s—“—sSs~sSCSOCCCCSCSC‘S* Gremlin industries, Inc.

San Boge, California 91023 LIST

|B {i-2-80] FORM NO. 001-1500

Page 24

BOO-0076 |S42| B

PHOTO JaIN CALC.

QTY PER ASS

PART NO

{51-0008 ij

-RCRSECECFL aS aE BEE ~l | O2234+ OBZO2

Q ~

Page 25

@remun ineustries, ins. - pita DUU-O00U/G]/P" =

PHOTO GOIN CAL

I TET TT ET

Page 26

es,ine. |PARTS|PITLE DB assy NO-D SH‘) B Sen Diegs, California 91023 LIST | PAWER SUPPLY DUAL OF +] REV

BHT 4 /8 “CUSIZE d cneck JZ, ave | APPR LTR] DATE REVISION DESCRIPTION DRAFT | CHECK | APPR | Pe [ean RELEABED re | ae Lee lB |i-+80] PER ECN 37 [= 7-BO Liew | Ae | ee

Enema Mn AN1_1enn

Page 27

"PL Aaay 800-0073 |sH 2] B

POWER SUPPLY DUAL

QTY PER ASSY

rT... DESCRIPTION f2| | | | [ear & 4700

/ CAP CER A585

Gremiin Industries, Inc. S

aa PIsf-fal=fet EL Tals Pi tt ISTE] a]

Page 28

PARTS [TILE Do Assy 800-0073 |su> List |POWER SUPPLY DUAL] — pwe No oF +1 rev fro] rart no Ferrer] ___oescriprion _—|_iner oes

NO ART NO [TTdftT, DESCRIPTION l22)47/-O272/5| | | | | RES 2.7K OHM [72 W S5&%l R7,R25,R26,R43, R46 23,471 - 03382 on [| [RES 3.2K OHM I72WSR REZ Cd | | [RES #70 OHM 172W 5%] R34, RPO J [R44 sd

i 27| 472-00 R5|4 29; 47 Smoo4| 7] San Biege, Caltforuia 92923 RES 0.5 OHM IW 5% | R4#,R29-R3B! . RES O.1 OHM SW S%( R28 I a PRO t—i‘iS:S | XSTR 2N#4OR | PxsTR TIPHIO [Oo siz [XSTR 2N440! [82,05 | |xsrR TIPHUS |[Q7 | XS TR TIP 29 W-¥-W- 5

SCHEMATIC

Page 29

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 30

QTY PER ASSY

PART NO Td DESCRIPTION

11 [/40-00185 [7] — CHASSIS, POWER SUPPLY

2 |

3] 211-0005 (Zz | 2 | [5 | FA & | 9 | 1 | D#G-32X-5f NUT HEX # @-32 Po

NUT HEX # 4-40 RIVET POP 37//lbL

Page 31

BVO -00 5!

26| 314-0015 | 3/4-001 8 | | U4 012,032 | | /C 740804 [35,004 4@ 7445/25 U13,U 40,047 pUGR

/C 74#L5S!75 /C 74#li244 /¢e 741508 U_37-39, 41, 71

l/c TELEIO 1C 74L542 (CQ 74ls574

28 | Ey 3t ale Gal : —!IN aE ¢ Ww 390-0003 4711-0220 471-001 471-0102 471-0103 aie ‘

Page 32

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 33

DESCRIPTION Lax CEP BO pf 5OvV CAP CER wf] pet 5OV-

i 2) stou C27-38,0+0-G7 i CAP FILM ./,,f (00v_ [ce 'S2-0017 GAPFEILM .33pf /00V_| C24 153-000] CAP TANT 10 wf 25V_ | 612,20,21,23,26, 68 2 9, 2 22

15 3-OD0C2 CAP TANT lyk Z25V aly I51- OO1] CAP CER .Olyf SOV CGI,CT7O [7O-O15O PCB CV. LOaAle

are 211-0004 CONN PIN TEST PT |TPI- TP4, GND

212-0063 |- CONN _M_4 PIN PLZD CONN M {2 PIN po SkT_ 14 PIN DIP | XU14, 30,69,70,29 | SKT 24 PIN DUAL XUZO-—XU2T BKT (6 PIN DUAL /VLN |XRP2XU5-8,33,34,44,49, Z XUS6-63 5, b6,50 ZID-OOGH [Zz SKT 49 P/N DUAL XU 43,453 Ol 2148-000 & SKT ZO FIN DUAL INLN | XUI-3.15.16,19, 28

  • | SKT 22 PIN DUAL _INLN | XUI7, XUIB

ga NN SKT_B PIN DIP XU KTAL ELK 15. 46845 ljyisSY

Les 313-0023 Ad

3/4-O000! [2 Foam aon nni—tKot

Page 34

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 35

ibe ASSY LOGIC BOARD DIGGER | 800-3066 DWG NO OF 2.

San Diego. Califorma 92123

DRAWN SON DUONG eur ;LTR] DATE | REVISION DESCRIPTION DRAFT | CHECK | APPR | fa |ea-co| REEDS a Gremlin/seca | PART FORM NO_ 001-1500

Page 36

TITLE

PARTS | Assy LOGIC BOARD DIGGE

PART NO

alS - 0019 315 - 0042

Page 37

ASSY LOGIC DIGGER | 800-3048

TABLE DWG NO

DRAWN AAKONEY ee, REVISION DESCRIPTION.

Enpas MA Ana sean

Page 38

et te] |

Page 39

parts |MTLE ASSEMBLY

LIST

a flan Diege, Cativornie 92023 5 @ ARE D'S! — DRAWN Wy Le

J Zz

FORM NO nn1.1600

Page 40

LIST QTY PER ASSY

fan age, Caterina SMES | [314-0058 2 [315-0019 3 | 315-0042 316-0507 800-0031 315-0051 IF PARTS | TITLE ASSY LOGI

PLT TT ET TTT TTT TT TT TT TT TT

Page 41

SHT 5, @ ARE"D'S1ZE [DRAWN Ly LTR DATE REVISION DES CRInS on

FORM NO N1.16Nn

Page 42

parts [TITLE 4.5, SEMBLY | 800-3033 |sH2| A UST | DIGGER SOUND 5

i 150-0004 |2 /53-0002| | 153 -OOF ABI i fi | 4 | | 2 = | 2 | Ea

Page 43

AwOEMVIDLI

DIGGER SAUND

PART NO DESCRIPTION

F711 - O1ORB OS /OK OHM (4*2W 5%

47 - DIO 4 47/-D/IO0S F7TI- OLS S RES

Vine LO 2CF 471-0225 F7l-~-O272 F7/-O0274 +7/-O275 ETI O Ao 471- O4F72 GTl- 9473 RES 77K OHM

F¢71-OF74 RES F¢7I-OKIl2 : RES F7I-DN5te3 RES

4F71- OVS4 B71 -CEe 4 4II- OR. Z FEI DOO IND/4 IN 4148 XSTR ZN 440]

FORM NO. 001-1501

Page 44

gromunineuseries,ine. | PARTS [TTLEAS SEMBLY | 00-3033

DWG NO

TE no} PART NO

  • #71 -O223 45| 471-0 3344 SH 4 A OF G| REV

RES 330K OHM 1/72 W 5%) RS

Page 45

REVISIONS, DESCRIPTION,

HARNEBS -| Boe EsB43

LT | COO _O® 60 ©®

SEC Yeu

RED 7 VEL 100 V

RED isoLation "SY. XFMR 560-005! c.V. LOGIC BOARD

4B ASHS PGND ACH2-I2 ole la}> [els T+] [eT]

ny HARNESS 300-3056

HARNESS 800-3054 : | HARNESS LE gaeness » Beats RELEASED

ie m eal Ey ta ey iy

  • on was iH tei cy tal PER Ser E)

WIRING DIAGRAM

[APPLICATION 1DO_NOT SCALE DRAWING. TOB-O0 15)A

Page 46

4 . 3 2 1 REVISIONS were ee eer eee Zone | UTR DESCRIPTION DATE APPROVED OPTIONAL assert ’” | RELEASED gape Pe fae @ l TO JUNCTION BOX GROUND L = x ee = de DO OR iS Cea a IMPER BOARD D

NOTES CONTINUED : a |p OPTIONAL TRANSFORMER P/N 560-0046

ELECTRO —_— HOME a 607-401 c

VIC LOGIC

B

Pp) ze coRD <

£ 9° > HARNESS faa ° 822-0007 VOLUME Y fr) CONTROL ae 8

800-0119 pS @ [ee Bhi. Ean) [ l @ Panis ust Gromiin Industries, Ine. ‘Bam Begs, Cabiternin OIE ZIP CORD a tT rt La TRUTH TABLE GAME POWER B options wes BUPPLY = BH - 3041 WIRING DIAGRAM DIGGER UPRIGHT ATW WO 700-0019

Page 47

REVISIONS Bel ‘DESCRIPRON DATE AT RELEASED Bo]

4009 40>

ESCAPE

R39

us us BR WZ @ NN po [po 4069

Ro? 1 MEG ci?

lp thin

409 4009

San Diege, California 9202S SCHEMATIC — sais f

sreciat eeone DIGGER SOUND BD.

  • ALL TRANSISTORS ARE 2N440) J ALL DOIDES ARE IN9I4 B00 3033 NOTES: paren

(DO NOT SCALE DRAWING

Page 48

REVISIONS mato BEsonirnen aye A [RELEASED w8 [4-1 6d A

SEE DETACHED PARTS LIST

Gremlin industries, Ine. Sen Binge, Californie 9112 ASSEMBLY —— DIGGER SOUND ZX, inSTALL FROM COROUIT SDE «

  • LAST VES. YSED C22, U9, RGS;D/, QI! J RUS RUB HARRIS RAI NET USED NOTES:
Page 49

US4 PING

+5v 741800 SET RE 7 FOR 4MB SQ AT PINT I R> I ' ' 16K

com ia taf start | of in pz Flum Inge HHH

ng 22 4240500 as Tales — 7m 2,2tt500 Az 0D ine

INDUT

PINS a 19 20 2) “SOCKETS USED 741500 10, 07 Db DS D4 D3 D2 DI Og

JUMPERS (HTS)

El-E 4, €3-£ ES-E7 €1-£4,83-E ES-E7

  • CUT ETCH To PIN 9 OF SOUND OUT CO Som PER Pin’ TO 459 FOR B29 O00! CUT ETCH BETWEEN UN-S # UI3-5 WNECTOR. ONLY.

JUMPER BETWEEN U13-5 2 048-17 FOR B2G-0004 ONLY NOTES! 7s as ees CE a

7 2708'S} and U26,23,2%23,22,21,20 a 2S Sere oe be fe ler2| COMPLETE CV LOGIC SCHEMATIC —

[sext 8 OFS 800-003! \E

Page 50

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 51

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 52

+PLACES

AOACA a40,2 g,G°0 "aed RAY i

  • be 86 FPREEEEEE 3 EG Bel ApGe BABU | a ee

ee ogee geeY

r

SEE DETACTED PARTS LIST

| ASSEMBLY — 24 BASIC VIC, BOARD

Page 53

SOFT SOLDER ETCH AND APPLY TAG WITH 800-0073 AND LATEST REVISIONS Zone | LTR DESCRIPTION A [RELEASED [B[ PER ECN 347

REY LETTER PART OR IDENTIFYING NO. NOMENCLATURE OR DESCRIPTION

UNCESS OTHERWISE SPECIFIED DIMENSIONS ARE IN. INCHES S ARE:

AN Alt WIRES 22 GA SOLDER TO BOTTOM

PARTS LIST Gremiin Industries, Inc. San Diego, California 92123 PC, ASSY POWER SUPPLY DUAL GAMES OF CONNECTOR PINS (CIRCUIT BIDE) NOTES: ‘SIZE [ CODE IDENT NO. [DRAWING NO, 800-0073 °

Page 54

an bo! DI MDA3500) s20V q = fe u f] A “| i O ov H 9 O | sSAHIELD o—_! 6 : 560-0003 LIL NOT ON P.C. BOAR Es en

2.7K

D/O D3 DI IN 5231 MRSO! | MRSOI

R20 IK

cay +7 10n Zz5v

a4 + Ol Sov REVISIONS ZONE | LTR DESCRIPTION A | RELEASED ~ [Pew ECN 307 wis | 1-4-a0] C [FER ECN 390 SB [a8 [HED

RIB RT 2K 1K

ya Tira |

ur DIMENSIONS ARE IN INCHES ES ARE: INLESS OTHERWISE SPECIFIED CONTRACT NO. Grenilin Industries, Inc. San Diego, California 92023 Preuss 3 SCHEMATIC —

pF POWER SUPPLY

DECIMALS ANGLES ceed bl APPROVALS

NEXT _ASSY DUAL GAMES IZE_] CODE IDENT NO. ORAWING NO. c BO0-D072

‘APPLICATION DO NOT SCALE DRAWING

Page 55

REVISIONS. DESCRIPTION A| RELEASED BI PER ECN 366

74L502

M4 “as WS) enseol ;

CREDITS/ UNIT 800 -0076|B

R2

  • oi F4LSO2 fe

To] eR PART OR NOMENCLATURE

REQO| IDENT IDENTIFYING NO. OR DESCRIPTION PARTS LIST UNLESS OTHERWISE SPECIFIED ng Ane Gremiin industries, inc. DECIMALS ANGLES ‘San Diego, California 92923 x 2 xx DW marca tin LOVEMATIC — PHOTO COIN CALC.

REV 800 -0076|8 SIZE TOENT NO, [DRAWING NO.

NEXT ASSY USED ON APPLICATION DO NOT SCALE DRAWING Scale NONE

Page 56

REVISIONS. DESCRIPTION

SEE DETACHED PARTS LIST

WY | CODE PART OR NOMENCLATURE. REQD | IDENT IDENTIFYING NO. OR DESCRIPTION PARTS LIST ow ree Pe Gremlin industries, Ine. TOLERANCES ARE: + |FRACTIONS DECIMALS ANGLES ‘San Doge, California 92113 al aX = = APPROVALS DATE a = [ie-1974 P.C. ASSEMBLY

‘SIZE | CODE IDENT NO. [ORAWING NO. BO0-O07G protic iel Pp —— wit} PHOTO COIN CALC NEXT ASSY USED ON, APPLICATION DO NOT SCALE DRAWING t a I) im Q

Q ie

Page 57

or & 7 6 5 F 4 3 2 1

  • BEVEIONS Toe Desonrrion ‘are | APPROVED a | RELEASED. [wy

xX t¢ ae Teprcat o€ ° eB aSSEnBL

q

S bad

woth no, | aed PARTS st Gremlin industries, Ine. ‘dan Binge, Catiternia 92022 AoveS: a ASSEMBLY. : Pe. baal BASIC COIN NECH DUAL SEE] CSG ERT 1 BONE RO rar TT ro APPLICATION, 00 NOT SCALE_ORAWING jscace WOVE SHEET 3 OF FZ a 7 i 6 5 4 3 2 1

Page 58

QUT WIRES, AT CONNECTOR

wut ET CHANGE TO THES. CONFIGURATION

WHT WIRE io 2)A\ Vig C-C_see sieeT 5 ROTATED 90° CCW MONITOR =MODIFICAT

io] B85 | coho Id. USE CABLE TIES, ITEM 20,70 DRESS WIRING AS NEEDED . wae A\ cane WIRE TO CHASSIS USING CABLE TIE, ITEM ZO ,THRU EXISTING HOLE . bad reek ie: Gremlin Industries, inc. ECMIALS San Beege, Cotiternia 92713 A Ayat WIRES TO LENGTHS SHOWN ON SHEET 8 AND SOLDER TO TERMINAL STRIP. AS USE HARDWARE HOLDING BLK WIRE TO CHASSIS TO MOUNT THERMISTOR TERMINAL STRIP WITH THERMISTER . aaa AM EROSE: a eae me /8\, REMOVE DEGAUSING COIL ROTATE 160° AND RESECURE . | Saal a — USEO_OW - (CUT POWER CORD TO LENGTH SHOWN ON SHEET 8 . NOTES: CONTINUED FROM SHEET S EXT ASST ‘APPLICATION 100 NOT SCALE DRAWING

Page 59

AL} A\wsta TRANSFORMER OVER VENT HOLE . uo

ea A (UNDERNEATH LID) (2) ig

REMOVE THERMISTOR ON MONITOR SEE SH A Now Located OO0°) i

  • (4) @)

(2) SEE DETAL AA

(46 {Q (3)

REMOYE DEGAUSING ‘SWITCH Oaa L e

ogo o eg fe) AN

NOTES CONTINUED ON SHEET 6 (2)

STAMP FREEPLAY ABOVE THIS LOCATION. @ @ BS FEMONE MICRO SWITCH FROM COIN MECHANISM AND. DISCARD . AS INSTALL CLIP SWITCH 13/4" FROM FRONT EDGE AND 8" FROM SIDE EDGE OF LID. QB INSTALL PHOTO CELL WITH ITEM37BY DRILLING A PILOT HOLE I2B DAMETER IN THE COIN BOX COVER . QS ROME LOWER COIN CHUTE AMO MOUNT FLUSH WITH BOTTOM OF COIN MECHANISM AS SHOWN TO MAKE ROOM FOR PHOTD CELL . NOTES: =i

fe) no \on \ VIEW_WITH ToP_REMOvED @)

OO ()

‘SPEAKER REF. ONLY

(2) 3 2 REVISIONS zoe [a BEscRIPTON Bare wernt A | RELEASED xD c= 9-60]

D

(e410 8

CON BOX COVER

TAL ACA c ASSY_DETAIL

CABINET CON CHUTE UPPER

ON. MECHANISM

B

COM Bor COVER cow cwTe wower /\, ft

= 9S fo] i ae TEM 18 8 DETAIL B-B

Ego] Gent | renting No. Oe OESCRIFHON I PARTS UST ivensions ane ie menes | [oNTMET NO: Gremlin Industries, Inc. [FRACTIONS DECIMALS ANGLES San Bioge, Californie 9223 > ae Terman [owe aoe PRAT So BUONG —_ [328-80 OP ASSEMBLY ona AMBROSE [6-39-86] DIGGER COCKTAIL

SEE DE WERT WS [BR WS Tey a D 700-0015 APRLICATION D0 NOT SOME Feme NONE aati 5 oF 8 2 1

Page 60

{PLAYER

COMPONENTS ARE SHOWN AS VIEWEO FROM WIRING SIDE OF PANEL

HARNESS ASSY REVISIONS, DESCRIPTION DATE “APPROVED Tone 24 A | RELEASED [2-4-8 AFA

280-0004 [CuiP, WIRE HOLD DOWN

800 - 3069 [HARNESS _ASSY.

800- 3070 NEXT ASSY as a DIGGER USED OW 800- 3068 CONTROL PANEL ASSY Paar oer rne W. "NOMENCLATURE OR DESCRIPTION

_ a i

DO NOT SCALE DRAWING CONTROL PANEL COMPLETE, DIGGER UPRIGHT

[oRARING WO 800 - 3074

Page 61

700-0019 JA

VIEW B-B (REAR PANEL AND DOOR REMOVED) TOP ASSY DIGGER UPRIGHT

Page 62

DATE | APpnoveD OM. [e-9-80] AFA

WOTES :

  • INSTALL WIRE HOLD S0WN CLIPS, ITEM 21, APPROX. AS SHOWN ON PRODUCTION ‘MOCK -UP.
  • INSTALL CABLE THES ITEM'S, AS REGD TO ORESS WARING . 3, INSTALL GROUND STRAP, ITEM 39, AS SHOWN ON PRODUCTION MOCK- UP.

7OO-O0I9 FA

SECTION A-A Si * bee Test Top assy

= DIGGER UPRIGHT

a 5 a 700-0019 APPLICATION. g