CATHODE RAY TOMES

Ridge Racer Upright

Ridge Racer (World, RR2 Ver.B) (Namco, 1993) · Document · 19 pages · 7 sections · original scan

Page 1

namco

RIDGE RACER’

UPRIGHT

Operators Manual

Part No 90500009

Page 2

© NAMCO Les- al rights reserved.

No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of phonographic recording, nor may it be stored ina retrieval system, transmitted or otherwise copied for public or private use, without permission from namco Ltd.

Published by: BRENT LEISURE Ltd. Unit 1 Brent Crescent, London. NW10 0QT

Phone:- 081-965-0550 Fax:- 081-961-0574

Page 3

Operators Manual... 1. 2. Contents

SPECIFICATIONS PRECAUTIONS .... 2-1 Cautions When Installing 2-2 Caution when Handling 2-3. When Transporting ADJUSTMENTS 3-1 Turning on the Power.. 3-2 Switches for Adjustments .. 3-3. Test Mode... 3-3-1 Setting the Game Fee an ptions Screen). 3-3-2 Changing the Game Settings (on the Game Options Screen) . 3-3-3 Switch Test 3-3-4 Sound Test (Adjusting the Sound Volume) .. 3-4 — Adjusting the Game After Replacing Parts (Initializing . HOW TO PLAY ooo. ececceceeeeeceeeeeseeseeeeeeeesaeeeseecaeseesaseeseesaeeeseaeneaes MAINTENANCE 5-1 Removing the Game Printed Circuit Board (PCB) . 5-2 Removing the Shield Case .............. 5-3 Removing the Power Control Panel 5-4 AB Pedal Assy (Replacing the Control) 5-5 Gear Shift Assy (removing) .. 5-6 Steering ASSY .........csceeeeeee 5-6-2 Replacing The Steering Wheel. PARTS SCHEMATIC

Page 4
  • SPECIFICATIONS

POWER SUPPLY :- 220/240volts AC

MONITOR:- Hantarex 26" Polo Colour Monitor with auto degause

DIMENSIONS :- 1205(w) x 895(d) x 1900(h)

WEIGHT :- 140kg.

ACCESSORIES :- Keys: (Cash Door) .. (Coin Assy) ... . ((Back DOOr) uci eeeeeeeeeeeeetees

Operators Manual .........cc cece eects 1

IEC Mains Lead ou... eee 1

Page 5
  • PRECAUTIONS

2-1 Cautions When Installing.

This game is designed for indoor use only. The game must not be installed outdoors or under the following conditions:-

a. In areas directly exposed to sunlight, high humidity, direct water contact, dust, high heat or extreme cold.

In locations that would present an obstacle in the case of an emergency, ie. near fire equipment or emergency exits.

On an unstable surface or subject to floor vibration.

2-2 Caution when Handling.

a. AC power must always be turned OFF, and the game disconnected, before replacing any parts or connecting/disconnecting connectors.

When unpluggung the game from an ellectrical outlet, always grasp the plug, not the mains lead.

The machine must be earthed with a securely connected earthed plug.

Care must be taken at all times to avoid electric shock when insopecting or adjusting the game.

Adjustment is required whenever the game PCB board, ROM,Steering Assy,AB Pedal Assy or Controls are replaced. See "3-4 Adjusting the Game after Replacing Parts" on page 12

2-3 When Transporting.

a. Do not subject the game to physical shock when transporting or moving it.

Page 6
  • ADJUSTMENTS

3-1 Turning on the Power

After installing the product, turn on the power. The power switch is located above the mains inlet on the rear of the main body.

3-2 Switches for Adjustments

Open the coin door to find the switches for adjustments.

  • Service switch.

Press this switch to increase the number of credits without incrementing the coin counter.

  • Test switch.

Set this switch to “ON” to enter test mode. You can change the game fee and so on, and perform various tests in Test mode. (See “3-3 Test Mode” on page 7).

SERVICE SW TEST SW ~ © ——

[~~ METER

Page 7

3-3 Test Mode

1. Open the coin door, then set the test switch to “ON”. The “Menu Screen” appears on the monitor display.

Select the item to be tested by turning the steering wheel right or left. The colour of the item you selected changes.

Step on the accelerator pedal to display the menu of the selected item. To return to the “Menu Screen”, step on the brake pedal (step on both the brake and clutch pedals on the Switch Test Screen).

When the test finishes, set the test switch to “OFF” to return to the Game Screen.

The Test switch must always be “OFF” during normal game mode.

MENU

COIN OPTIONS ——}(1) For setting the price of play (See 3-3-1)

GAME OPTIONS ——}|(2) For setting the game options (See 3-3-2)

BOARD TEST ——|(3) For testing the game PCB

SWITCH TEST ——|(4) For testing switches (See 3-3-3)

SOUND TEST ——|(5) For adjusting the sound volume (See 3-3-4)

MONITOR TEST ——|(6) For monitor adjustments

ADS TEST —|(7) For displaying the game data collected

ABOUT ——|(8) For restoring each setting to standard value

IN = STEP ON THE GAS

Page 8

3-3-1 Setting the Game Fee and So On (On the Coin Options Screen)

Select 1 “COIN OPTIONS’ on the Menu Screen to set the game fee and so on.

Turn the steering wheel to select the item to be changed, then step on the accelerator pedal.

Turn the steering wheel again to change the setting, then step on the accelerator pedal (See table 1.)

Step on the brake pedal to return to the Menu Screen.

Note: The price of play adjustments are made on the credit COIN OPTIONS

GAME COST

2 COINS 1 CREDIT

COIN 1 MECH VALUE

1 COIN COUNT AS 1 COIN

COIN 2 MECH VALUE

1 COIN COUNT AS 1 COIN

BONUS FOR QUANTITY BUY-IN

NONE

FREE PLAY

OFF

EXIT = STEP ON THE BRAKE -—— (a)

T—— (b)

r—— (©)

r—— dd)

board and the coin options should be set as the following table.

Item Description

(a) Game feeNumber of credit pulses necessary for game creditOne to nineSet to 1
(b) Coin 1 mechanism | Number of credit pulses per coinOne to nineSet to 1
  • Coin 2 mechanism | Not Used One to nine
  • Bonus The extra credit given as a bonus when the specified | One credit per one coin
number of coins are insertedThree credits per nineSet to NONE

coins

(e) Free playFree play started by stepping on the acceleratorOFF/ONset to OFF
Page 9

Select 2 “GAME OPTIONS” to change the game options.

Turn the steering wheel to select the item to be changed then step on the accelerator pedal.

Turn the steering wheel again to change the setting, then step on the accelerator 3-3-2 Changing the Game Settings (on the Game Options Screen)

pedal (see table 2).

Step on the brake pedal to return to the Menu Screen.

GAME OPTIONS

(DEFAULT IN GREEN)

GAME DIFFICULTY TIME EXTEND

NOVICEDoaths

ADVANCED D EXPERT Dost ee

Tr.Do#eHe ee

LAP NOVICE 2

ADVANCED 3

EXPERT 3

Tr. 3

SPEED KM/H

SOUND IN ATTRACT

ON

EXIT = STEP ON THE BRAKE wee ee —f

Settings of the Game Options Screen (a)

(b) ©

@)

© (O

(g) (h)

@

@

Item Description Factory setting

(a) Play time for the novice levelA (shortest) to H (longest)D
  • Play time time for the advanced level _| A (shortest) to H (longest) D
(c) Play time for the expert levelA (shortest) to H (longest)D
(d) Play time for the time trial gameA (shortest) to H (longest)D
(e) Laps for the novice level2to5S2
(f) Laps for the advanced level2toS3
(g) Laps for the expert level2toS3
(h) Laps for the time trial game2toS3
  • Unit of speed KM/H (kilometer) MPH (Mile) Set for country of use
  • Attract sound ON/OFF ON
Page 10

3-3-3 Switch Test

Select 3 “SWITCH TEST” to display the following screen.

h. i. j- SWITCH TEST

DIP SsW2 12345678 ——______________|(a) Option switch (SW2 on the CPU) SW3 12345678 ———————— (b) Option switch (SW3 on the CPU)

STEERING — *0000——_____________|(c)_ Steering GAS *0000 | ()_ Accelerator BRAKE *0000 —— e) Brake CLUTCH OFF ———————————— (f Clutch SHIFT N SWITCH | OFF (g) Shift SWITCH 2 OFF

SWITCH 3 OFF

SWITCH 4 OFF SERVICE OFF ~~] (h) Service switch COIN 1 OFF ————————] (i) Coin 1 switeh COIN 2 OFF ~~ ]@) Coin 2 switch

EXIT = STEP ON THE BRAKE AND ACCELERATOR

The status of the option switch SW2 on the game PCB (CPU-PCB) is indicated here. The status of the option switch SW3 on the game PCB (CPU-PCB) is indicated here. The SW2 or SWS switch is set to ON when the corresponding number is red. When you turn the steering wheel to the right, the number increments. When turning it to the left, the number decrements. When you step on the accelerator pedal, the number increments. When you step on the brake pedal, the number increments. An approximate value of “0000” appears on the item c, d or e respectively when you locate the steering wheel in the middle and when the accelerator and brake pedals are released. (Even if the least digit of the number changes, the game is operating normally). “OK” appears to the right of the number when the accelerator and brake pedals are depressed. “ON” appears when you depress the clutch pedal. The position of the shift (1 to 6, N) and the status of four switches are indicated here. When you move the shift lever forwards, the switch 1 is set to ON. When you move it backwards, the switch 2 is set to ON. When you move it to the left direction, the switch 3 is set to “ON”. When you move it to the right direction, the switch 4 is set to ON. “ON” appears when you press the service switch inside the coin door. “ON” appears when you operate the coin 1 switch. Not used.

To return to the Menu Screen, step on both the brake and gas pedal at the same time

Page 11

3-3-4 Sound Test (Adjusting the Sound Volume)

Select “SOUND TEST” on the menu screen to adjust the sound volume. The following screen appears.

SOUND TEST

VOLUME(L) 3F ——] (a) Sound volume for left speakers

VOLUME(R) 3F —__1} (b) Sound volume for right speakers

STEREO CHECK 1 (c) Stereo checking function

SONG 00

EXIT=STEP ON THE BRAKE

Use the steering wheel to select the item to be changed. Step on the accelerator and the item selected will stop flashing. Use the steering to adjust the level. Step on the accelerator when the desired setting is reached and the item will start flashing. The steering can now select another item.

The sound volume can be adjusted in 64 steps between 00 (minimum) to 3F (maximum). The factory setting is “SF”. (i.e. Loudest)

When you select (c) and step on the accelerator pedal, sound is produced the left speaker, then the right speaker. Step on the brake pedal to return to the Menu Screen.

Page 12

3-4 Adjusting the Game After Replacing Parts (Initializing the Game)

Be sure to adjust the game with the following the instructions below after replacing any part. Otherwise, the game will not function correctly.

1.

5. Ensure that the accelerator and brake pedals are released and the steering is in the centre.

Hold down the service switch and slide to the test switch to “ON”. The

ADJUST

STEERING 0000

GAS 0000

BRAKE 0000

following screen appears on the monitor display.

To zero the settings press the service switch.

When each number on the right hand side of the items: STEERING, GAS and BRAKE is about “OOOO”, the adjustments are complete.

Set the test switch to “OFF” to return to the Game Screen.

The test switch must always be “OFF” during normal game mode.

Page 13
  • HOW TO PLAY

This is the car race game.

Four difficulties are provided: NOVICE, INTERMEDIATE, ADVANCED and T.T. (Time Trial)

(Outline of a Game)

When a player drives a car the specified number laps within the given time, he or she finishes the race, the ranking, lap time and total time are displayed and the game is over.

If the remaining time becomes “O” before a player finishes the race, the game is over.

(Starting a Game)

Insert coins, then select the difficulty. Turn the steering wheel to select the difficulty from NOVICE, INTERMEDIATE, ADVANCED and TT, then step on the accelerator pedal to set it.

If a player does not select the above items within 10 seconds, the game sets its choices by itself.

(Difference of the Difficulty Levels)

When a player selects the NOVICE level, he or she drives a car on the MAIN COURSE at a low speed. This is the player’s car vs. computer driven cars race game.

When a player selects the INTERMEDIATE level, he or she drives a car on the MAIN COURSE ata high speed. This is the player’s car vs. computer-driven cars race game.

When a player selects the ADVANCED level, he or she drives a car on the MAIN COURSE and a TECHNICAL BRANCH at a high speed. This is the player’s car vs. computer-driven cars race game.

When a player selects the TT level, he or she drives a car on the MAIN COURSE and the TECHNICAL BRANCH at a higher speed than that of the ADVANCED level. This is the player’s car vs. a computer-driven car time trial race. When a player clocks a good time, they can record their name.

Page 14
  • MAINTENANCE

5-1 Removing the Game Printed Circuit Board (PCB)

1. Remove the back door,

Remove two assembling bolts (M6 X 30), then pull out the power control panel about 25cm. (Note: if you pull it out too much, it will be detached).

Disconnect two connectors on the EMI board, then remove six cup screws (M4 X 10) from the shield case door. (Do not lose internal washers).

Take care not to damage the connectors between the EMI board and the main PCB to remove the shield case door, then take out the main pcb.

Remove two cup screws (M4 X 10) from the I/O door. (Note: Do not remove other screws).

Remove the I/O door, then disconnect four connectors of the |I/ O PCB.

Take out the I/O PCB. Shield case Back cover (L)

Cup screw (M4 x 10)

Assembling bolt (M6 x 30) Angle bracket

Power control ‘panel

Shield case door

Cup screw (M4 x 10) Main PCB AC fan

VO PCB

EMI board

Internal : \ washer (M4) Cup screw (M4 x 10) | Cup_screw (M5 x 14)

Page 15

5-2 Removing the Shield Case

  • Perform Steps (1) and (2) described in Section 5-1.
  • Disconnect the connector of the AC Fan.
  • Remove two cup screw (M5 X 14) then take out the shield case.

5-3 Removing the Power Control Panel

1 Perform steps 1, 2, 5 and 6 described in Section 5-1.

  • Disconnect two connectors of the EMI board, remove a cup screw (M4 X
  • from the shield case door, then remove the ground terminal. (Note: do not lose the internal washer).
  • Disconnect the connectors connecting the power control panel and the main body assy: one connector on the right side and two connectors on the left side then remove the power control panel.

5-4 AB Pedal Assy (Replacing the Control)

  • Remove four hex head bolts (M6x20) and withdraw the assy forward .
  • Loosen the quadrant gear clamp screw and remove the quadrant gear.
  • Loosen the gear grub screw and remove the gear.
  • Replace the control potentiometer.
Note: When re-assembling a. Ensure that the potentiometer locating tag is engaged in the mounting plate cutout. b. Turn the potentiometer shaft almost fully clockwise before engaging the quadrant gear.

5-5 Gear Shift Assy (removing)

  • Open the play panel assy and disconnect the four way connector.
  • Remove four M4 coach bolts and withdraw the shifter assy.
Page 16

5-6 Steering Assy

5-6-1 Replacing the control

  • Open the play panel assy to gain access to the steering assy.
  • Loosen the grub screw on the gear wheel and remove the gear wheel.
  • Replace the control potentiometer.
  • Replace the gear wheel and retighten the grub screw securely.
Note: When replacing the control potentiometer ensure that the locating tag of the potentiomer is located in the hole in the mounting bracket and the pot shaft is at its mid travel before tightening the gear grub screw.
  • Re-initialize the game (See 3-4 Adjusting the Game - page 12) before the game is played.

5-6-2 Replacing The Steering Wheel

  • Remove the centre cover of the steering wheel.
  • Remove three socket button heads (M6x16)
  • Pull off the steering wheel, then replace it with a new one.
Page 17
  • PARTS

DESCRIPTION PART No

Monitor 26" Hantarex Polo 84000010

Speaker 41/2" 20w (with shield can) 62000006

Dual Pedal Assy (with pots) 88800029

Dual Pedal & Steering Pot (5k) 76000652

Steering Assy (270 deg) 88800001

Gear Shift assy 88800009

Power supply Assy - 5v/30a 83000004

Schaffner Mains In Assy 66000016

Fuse 5a 20mm 63500601

Interlock Switch 60000006

Fan 67000015

Fluorescent Tube 18" 64500000

Choke 15w 63300000

Front Glass 31000008

Side Decal L.H. 40000033

Side decalR.H. 40000034

Play Instruction Plexi 45000161

Top Flash 30000028

Manual 90500009

Page 18

270 deg Steering Assy ccoonos?*

88800043 \—q ©

88800018, sseooi9 88800010 SAN

88800036 ee als "45000167 3 \ 128800029

PART No DESCRIPTION 88800008 | Wheel Only 88800010 | Adaptor 45000167 | Steering Wheel Spacer 88800011 | Spring 88800012 | Gear - Large 88800013 | Gear - Small 88800014 | Steering Insert 76000052 |5K Pot 88800016 | Spring Link Shaft 88800018 | Steering Shaft 88800019 | Woodruff Key 88800035 | Stop Unit 88800036 | Steering Arm Bearing 88800037 | Steering Arm 88800038 | Spacer 88800039 | Pot Bracket 88800043 | Centre Cam Weight

Page 19

a

  • SCHEMATIC