CATHODE RAY TOMES

Robotron Instruction Manual (16P-3005-101) Mar 82

Robotron: 2084 (Solid Blue label) (Williams / Vid Kidz, 1982) · Instruction Manual · 11 pages · 13 sections · original scan

Page 1

16P-3005-101 Hilliams Y mani

AOBO moO:

INSTRUCTION MANUAL

Including procedures for...

¢ Operation

¢ Auditing

e Adjustment

  • Diagnostics

‘or service. YW Mai ©

NOTE NeWITOLL- FREE TELEPHONE NUMBERS: Mtams ELECTRONICS, INC 800-621-1253 3401 i oa mor a Av. Ch sata
Page 2

diyp yeroodg 8XMr ‘WOU 8XZ1¢ ‘NOUd 8XZ1¢ ‘NOUd 8x4 ‘WOUd 8XIb ‘WOUd 8XIp ‘WOUd 8x ‘WOUd 8x ‘WOUd 8X ‘WOUd 8XIb ‘WOUd 8X ‘WOUd 8XIb ‘WOUd 8X ‘WOUd 8XIb ‘WOUd 8XIb ‘WOUd NOILdIaosaa

T1660-O017S-V O1660-EreES-V 1T860-CPES-V 76960-CPES-V 60660-EreS-V 80660-ErES-V L0660-EVES-V 90660-CrES-V S0660-E7ES-V p0660-CPES-V €0660-€7ES-V 70660-EVES-V 10660-C7ES-V 00660-EreS-V 66860-EPeS-V 86860-CreS-V “ON LUVd

T diya peroadg € WO’ Punog OsplA (Te9n12A) 9 WOU Jeposeq ([eUOZIIOH) INOW Joposeq dcl NOULOGON dil NOWLOdON d0l NOWLOdON d6 NOWLOdOUN d8 NOWLOdOUN dL NOWLOGOUN d9 NOWLOGOUN ds NOWLOdOUN dv NOWLOGOUN de NOWLOGOUN dc NOWLOdOUN dl NOWLOdOaN Woda AUYVWWAS NOU

Page 3

POWER TURN-ON

CAUTION - This game must be plugged into a properly grounded outlet to prevent shock hazard and to ensure proper game operation. DO NOT use a "cheater" plug to defeat the ground pin on the line cord, and DO NOT cut off the ground pin.

WHEN THE GAME IS FIRST TURNED ON it produces a sound. Simultaneously general illumination should come on and a moment later a scanning “rug pattern” indicating the RAM test should appear on the screen. Next the rug should become stationary as the ROM test is performed. In a correctly running game the rug pattern will be followed by the message "INITIAL CHECKS INDICATE: OPERATIONAL". If RAM or ROM failure messages come up on the screen instead, refer to Power-Up Tests in TROUBLESHOOTING PROCEDURES.

GAME OPERATION

GAME START - Insert coins; a random sound is produced and credits are displayed on the CRT. With one or more credits displayed, pressing 1-player start initiates a l-player, *3-turn game. With two or more displayed, pressing 2-player start initiates a 2-player, *3-turn game.

PLAYER CONTROLS

MOVE JOYSTICK (LEFT) maneuvers mutant clone (our hero) in any of eight directions: N-NE-E-SE-S-SW-W-NW.

FIRE JOYSTICK (RIGHT) fires anti-robot laser gun in same eight directions.

GAME PLAY

ROBOTS ARE THE ENEMY - The player (represented by the mutant clone) must deactivate six types of robots with a laser gun. However the robots’ armada including tanks, electrodes and cruise missiles will be deployed against the mutant. Meanwhile defenseless normal clones must be protected by the mutant or they will be captured and reprogrammed by the robots. Arriving at 25,000* points (or any multiple of 25,000), the mutant is awarded a new opportunity to defend his clonekinsmen.

HIGH SCORE SIGNATURE

Select letters with the MOVE joystick. Push up to move forward through the alphabet; pull down to move backward. Then push the FIRE joystick up to lock in the letter.

BOOKKEEPING AND EVALUATION TOTALS

  • In Game-Over Mode, open the cashbox and depress the cashbox advance switch. The advance switch located on the coin door can also be used. The CRT should indicate all bookkeeping and evaluation totals. If so, go to step 3. If the CRT display comes up in the ROM test, perform step 2.
  • Continue to depress the cashbox advance switch, stepping the game through test programs for ROMs, RAMs, CMOS RAMs, color RAMs, sounds, switches, and then CRT test patterns, of which there are five. The fifth test pattern, color bars, directly precedes the CRT display of the bookkeeping and evaluation totals.
  • The bookkeeping and evaluation totals appear on the displays as in Figure 1.

CLEARING BOOKKEKPING TOTALS

Depress ADVANCE to display Game Adjustments. Operate MOVE joystick to position cursor on CLEAR BOOKKEEPING TOTALS. Push FIRE. Depress ADVANCE. Ree

  • Adjustable feature
Page 4

BOOKKEEPING TOTALS

LEFT SLOT COINS 167 CENTER SLOT COINS 0 RIGHT SLOT COINS 426 PAID CREDITS 593 EXTRA MEN EARNED 221 PLAY TIME IN MINUTES 1200 MEN PLAYED 2000 CREDITS PLAYED 593

AVERAGE TIME PER CREDIT 2:01

AVERAGE TURNS PERCREDIT _ 3.37

Figure 1. Bookkeeping display

GAME ADJUSTMENTS

In the Game-Over Mode open the coin door with AUTO-UP, and depress the coin door ADVANCE switch twice to cause a CRT display as shown in Figure 2.

To select and then set functions to the desired values, use the MOVE (UP-DOWN) joystick to select the that is to be changed and then, making sure the coin door is open, use the FIRE (UP-DOWN) joystick to increase or reduce the value of the selected function.

The number of turns per game can be set anywhere from 1 to 20 (3 recommended). Difficulty is factory-programmed at 5 (moderate; recommended). It can be custom-programmed as desired.

Game pricing is selected with standard settings or with custom settings as shown in Tables 1 & 2. Table | lists some common pricing schemes and directs the reader to the proper entry in Table 2, which shows what the CRT display should look like to accomplish the desired pricing. Note that free play can be elected by entering the code number 9 at the PRICING SELECTION function (see Tables | and 2).

For standard settings you need change only the PRICING SELECTION. For custom settings, first set PRICING SELECTION to zero and then set the remaining values according to Table 2.

Page 5

GAME ADJUSTMENT

EXTRA MAN EVERY 25000 RECOMMENDED TURNS PER PLAYER 3 RECOMMENDED PRICING SELECTION LEFT SLOT UNITS CENTER SLOT UNITS RIGHT SLOT UNITS UNITS REQUIRED FOR CREDIT UNITS REQUIRED FOR BONUS CREDIT MINIMUM UNITS FOR ANY CREDIT

FANCY ATTRACT MODE DIFFICULTY OF PLAY LETTERS FOR HIGH SCORE NAME RESTORE FACTORY SETTINGS NO CLEAR BOOKKEEPING TOTALS NO HIGH SCORE TABLE RESET NO AUTO CYCLE NO SET ATTRACT MODE MESSAGE NO SET HIGH SCORE NAME NO USE -MOVE- LEVER TO SELECT ADJUSTMENT USE -FIRE- LEVER TO CHANGE THE VALUE

PRESS ADVANCE TO EXIT costs w

< oan Oo

Figure 2. Game Adjustment

Highest Score Signature 1/QUARTER 4/DOLLAR

RECOMMENDED RECOMMENDED

The number of letters allowed the highest scoring player for entering his name can be varied from 3 to 20 and is recommended as 3. If objectionable words are entered as the signature name, you can change the lettered entry leaving the highest score the same. See Setting Highest Score Name.

Restore Factory Settings

  • Position the cursor on RESTORE FACTORY SETTINGS.
  • Push FIRE.
  • Depress ADVANCE.

Resetting High Score Table 1, Position the cursor on RESET HIGH SCORE TABLE.

  • Push FIRE.
  • Depress ADVANCE.

Setting Attract Mode Message Position the cursor on SET ATTRACT MODE MESSAGE. Push FIRE. Depress ADVANCE. Enter up to two lines of your message following instructions on the screen Depress ADVANCE to terminate process. ARWNe

NOTE: To restore the Williams attract mode message, it is necessary to perform steps | through 3 and then turn the game OFF then ON.

Setting High Score Name 1 Position the cursor on SET HIGHEST SCORE NAME.

  • Push FIRE.
  • Depress ADVANCE. 4 Enter new signature; depress ADVANCE to terminate process.
NOTE: An alternate, simpler method enters the factory highest score signature. In the game over mode, hold HIGH SCORE RECRT Nanraccad Aftar a faur canande a connd ic nendnaad and the fantary himhact conra cianatire hac haan antivatad
Page 6

Table 1. Pricing Schemes

TABLE 2

COIN DOOR MECHANISMCREDITS/MONEYSTANDARD SELECTION/

CUSTOM KEY Twin Quarter 1/25¢, 5/$1 Quarter, Dollar, Quarter 2/50¢, 5/$1 1/25¢, 4/$1 2/50¢, 4/$1 1/50¢, 3/$1, 4/$1.25 1/50¢, 3/$1, 7/$2 1/50¢, 3/$1, 6/$2 1/50¢ 1DM, 5DM 1/1DM, 6/5DM. 20-Cent, 50-Cent 1/20¢, 3/50¢ 1 Franc, 5 Franc 1/2F, 3/5F rof4 Halt w wloolrlolalalalafajolu-moaww > 25 Cent 1/25¢, 4/1G 1 Guilder 1/25¢, 5/IG 5 Franc 1/SF, 2/10F 10 Franc 1/10F 1 Franc, 2 Franc 2/1F 5/2F 100 Lire, 200 Lire 1/200 Lire Twin Coin 1/1 Coin 1/2 Coins 1/3 Coins, 2 5 Coins 1 Unit, 5 Unit 1/2, 3/5 1/1, 5/5 1/3, 2/5 FREE PLAY -

Table 2. Pricing Settings

DISPLAY CUSTOM KEY FUNCTIONS STANDARD SELECTION A|B{IC|D/JE/F/G/H|I|J

Pricing Selection12/3}4]5/]6)7;)8/9/]0]0/0]0]0;/0)0}]0}]0)0
Left Slot Units16}11111111113 | 12]61212
Center Slot Units4/0)/4]16}4);0]0;)/0/4)]444/4)]12)/48;/0)]0],0]0)0
Right Slot Units11161}4)2)211113 | 12)15}4]2]5 | 10
Unitsper Credit2112/211211114)14]51515

Units for Bonus Credit 4/0/;/0]0]0;0]0)]0/0)]4)4/]/0]15])/96;}/0)4]0}]0)]0 Minimum Units forCredit | 0 | 0 | 0/|0/0/[/0]0}/0/0/0{2/2]0{24/0|]0]0]0/0

Page 7

TROUBLESHOOTING PROCEDURES Certain types of game malfunctions may inhibit the game's diagnostic or display faculties. Troubleshooting procedures for most of these types of malfunctions as well as malfunctions that permit self-diagnosis are covered below. Our troubleshooting algorithm begins with Power-Up and continues until Game Over Mode. All procedures can be performed with minimal test equipment or merely by observing the game itself. POWER-UP TESTS NO GENERAL ILLUMINATION NO INITIAL VIDEO (RUG PATTERN) CHECKING POWER SUPPLY BOARD

  • Check fuse F2 on power supply board.
  • Check for proper installation of jumpers W1, W2, W3 and/or resistor R27. (Some machines DO NOT have an R27. Refer to your drawing set.)
  • Check 4P1/J I, 4P3/J3, 6P2/J2 and 6P3/J3.
  • If all the above don't turn up the problem
  • Open back doors
  • Press reset button on CPU Board.
  • Try RAM and ROM tests (see below).
  • If all the above don't turn up the problem, check power supply board.
  • Swap power supply board with one from known-good game.
  • If game plays, problem is on power supply board.
  • If game doesn't play, check power transformer with voltmeter.
  • If known-good power supply is unavailable check power supply board. for tests above, check +5V,— 5V and + 12V outputs on power supply in game. Each MUST BE within 2% of rated output.

MORE POWER-UP TESTS ROM BOARD | ROM BOARD TEST LEDS LEDS VIDEO REMEDY RECOGNIZE IDENTIFY

CONDITION CHIPS

GENERAL“0” meansall| -(1) Scanning rug patternIf any video (see left) is missing or
power-up tests(2) Stationary rug patternerror message is displayed, proceed to
passed(3) "INITIAL TESTS INDICATE:Diagnostic Mode tests.

OPERATIONAL"

  • Game-Over Mode
CMOS“OQ” means tests | -“HIGH SCORE TABLE RESET”(1) Open coin door and turn power

(See Appendix A) | passed “ADJUSTMENT FAILURE”

OPENING FRONT DOOR AND “BOOKKEEPING TOTALS CLEARED”

“RESTORE FACTORY SEITINGS BY

_TURNING GAME OFF AND ON” off and on.

“0” means t“FACTORY SEITINGS RESTORED”(2) Press ADVANCE.Gameshould

passed return to Game-Over Mode.

BATTERY“OQ” means tests | -“HIGH SCORE TABLE RESET”(1) Open coin door and turn power
(See Appendix A) | passed“BOOKKEEPING TOTALS CLEARED”off and on. Or press ADVANCE. In

“ADJUSTMENT FAILURE”

OPENING FRONT DOOR AND “RESTORE FACTORY SEITINGS BY

TURNING GAME OFF AND ON” either case, game should return to Game-Over Mode.

  • Check AA alkaline cells on CPU Board.
  • If problem persists proceed with CMOS RAM test by putting the game into its Diagnostic Mode (see SELF- DIAGNOSTICS). MEMORY “OQ” means tests | - PROTECT passed INTERLOCK (See Appendix A) “HIGH SCORE TABLE RESET”

“ADJUSTMENT FAILURE”

OPENING FRONT DOOR AND “BOOKKEEPING TOTALS CLEARED”

“RESTORE FACTORY SEITINGS BY

TURNING GAME OFF AND ON”

  • Making and breaking coin door interlock switch, check with VOM and replace if faulty.
  • Replace if faulty: Memory protect gates 6E, IC1, Ql, or CMOS RAM Ic. SPECIAL CHIP “OQ” means tests | passed
  • Scanning rug pattern.
  • Blank screen
  • Intro blank or program crash. stead of “INITIAL TESTS INDICATE: OPERATIONAL”
  • High score table with no scores.
  • Turn power off.
  • To find bad chip replace 2 special chips one at a time with known good chip:
  • Turn Machine on after each replacement and run through Power- Up Tests.
Page 8

SELF DIAGNOSTICS

If RAM or ROM failure messages are displayed on the CRT after the “rug pattern” proceed with self-diagnostics. Selfdiagnostic procedures are controlled by the AUTO-UP/MANUAL-DOWN and ADVANCE switches in the coin door. Set the AUTO-UP/MANUAL-DOWN switch to the MANUAL-DOWN position and depress the ADVANCE pushbutton. The game is now in its Diagnostic Mode and a ROM test is performed. With ROM test results present on the CRT display, depressing the ADVANCE pushbutton initiates the RAM test. Further tests (CMOS, sound, switch, color RAM, monitor test patterns) are encountered one after the other as the ADVANCE pushbutton is depressed (once more for each subsequent test).

MONITOR TEST PATTERNS - For ease in monitor adjustments, the monitor may be slid back and the screen viewed in a mirror. Remove the two bolts and carefully slide the monitor back in its shelf; secure the monitor in the extended position by inserting the two bolts though holes in the monitor base and monitor shelf provided at the left side of the monitor.

AUTO CYCLE MODE - From the color bar pattern (or Game Over with the switch set to AUTO-UP) depress ADVANCE two times to display GAME ADJUSTMENTS.

  • Position the cursor on AUTO CYCLE with the MOVE Joystick and push the FIRE joystick up.
  • Depress ADVANCE.
  • The system will now sequence through ROM, RAM, and CMOS RAM tests repeatedly. The coin door must be open during the Auto Cycle test. If an error is detected, the test is terminated and the failure indication is displayed on the CRT.
  • To terminate the Auto-Cycle test, turn the game OFF and ON.
  • EGCASS
  • FRSRGEB

~ FRRRBEE

Figure 3. RAM Location and Numbering on the CPU Board (See above)

Page 9

DIAGNOSTIC MODE RAM AND ROM TESTS ROM BOARD ROM BOARD TEST LEDS LEDS VIDEO REMEDY

RECOGNIZE IDENTIFY

CONDITION CHIPS

ROM“2” means ROM2-digit ROM“ROM ERROR” and ROM chip no.(1) Turn power off.
error.chip number(2) Replace suspected chip.
RAM“1” means RAMBank number“RAM ERROR” followed by RAM(1) Check for normal voltages on
error.first ... thenbank number and chip number (Note: | indicated RAM chip: -5v/pin 1,
chip number in|with multiple RAM failures this+12v/pin 8, +5v/pin 9.

aa (see figure | display may not appear) (2) Turn power off.

  • Replace suspected chip.
  • With multiple RAM failures always check power supply. See POWER-UP TESTS.
CMOS“3” means CMOS | -“CMOS RAM ERROR OR WRITE

(See Appendix A) RAM error PROTECT FAILURE”

  • Check pin 22 of CMOS RAM for +3.8VDC. If present, replace CMOS chip IC. If absent replace AA alkaline cells.
  • With new alkaline cells, check for +3.8VDC. If still absent, replace diodes D9 and D10.
  • Upon power-up and re-entry into diagnostics if CMOS error message persists replace memory protect gates 6E, IC1, QI and address decoder 4G/6J. SPECIAL CHIP No ~ indicated by CRT display in color test only. Thick vertical band indicates color RAM fault Replace | B, 2B or color analogue circuit. If both RAMs appear bad, may actually be flip-flop 1A See Table 3 and Figure 4 for details.

COLOR RAM TEST - TEST 4

  • CRT SEQUENCES THROUGH COLORS, 2 SECONDS EACH
  • VERTICAL BAND INDICATES COLOR RAM FAULT.

Figure 3. Color Test Table 3. Which Color RAM is Bad? COLOR FAULT SEQUENCES RAM 1B RAM 2B 1 Light red Too-light or too dark | Magenta band 2 Red red or gray band 3 dark red

4 Light greenYellow bandCyan band

5 Green 6 Dark green

7 Light blueMagenta bandToo-light or too dark

8 Blue blue or gray band 9 Dark blue

4 Light greenGreen bandDark green band or

ray band

5 GreenLight green bandDark green band or

gray band

6 Dark green-Grey band
Page 10

MORE DIAGNOSTIC TEST MODES

Tests 5 and 7 provide sequential subtests. To stop automatic cycling set switch to MANUAL-DOWN. Depress ADVANCE in MANUAL-DOWN to step through subtests.

SOUND TEST - TEST 5

From color RAM test, depress ADVANCE in AUTO-UP.

SWITCH TEST - TEST 6

CRT indicates AUTO-UP closed and any stuck switches. Set black coin door switch to MANUAL-DOWN and clear any stuck switches. CRT should indicate no switches closed. Operate switches and check for display of switch name.

MONITOR SET UP TEST PATTERNS - TEST 7

From Switch Test depress ADVANCE in AUTO-UP. The color bar pattern is also analyzed to detect color RAM faults. If color RAM Test 4 indicates no faults, a doublewidth band, half width bands, transposition or missing bands indicates a fault in 1A, 1B, 2B or 2C chips.

SOUND BOARD DIAGNOSTICS Table 4. Tracing the Missing Sound Test sequences, sound lines 1 through 6:

Missin; Check

2P4/1OP3 Pin 3 2P4/10P3 Pin 2 2P4/10P3 Pin 5 2P4/10P3 Pin 4 2P4/10P3 Pin 7 2P4/10P3 Pin 6 Perform sound board diagnostics Zoausuna

Table 5. CRT Display for Each Switch Coin Door Player Panel ADVANCE 1- PLAYER START AUTO-UP 2- PLAYER START HIGH SCORE RESET MOVE UP LEFT COIN (next to hinge) MOVE DOWN CENTRE COIN MOVE LEFT RIGHT COIN' MOVE RIGHT SLAM SWITCH FIRE UP FIRE DOWN FIRE LEFT FIRE RIGHT

Table 6. Patterns Indicate Problems Pattern Alignment/Adjustment Vertical and Horizontal Linearity, Convergence, Focus Cross Hatch

Red i i nite } Color Purity } Color bars 1293 4°95 6 78

8= Figure 4. Color Bar Pattern

Depress the DIAGNOSTIC pushbutton on the bottom of the Sound Board. A check is made of the Sound ROM and sounds are produced if the check is good. If sounds are produced but not in Audio Test 5 check for ROM board PIA output on Sound Board inputs that are stuck low. If no sound is produced either the Sound ROM, IC12, input power, or other Sound Board circuitry is faulty.

Page 11

APPENDIX A

CMOS RAM Data Test Protocol

POWER ON The first sub-test of the CMOS RAM data is that of the ATTRACT MODE par MESSAGE checksum. If the test does not pass, the factory ATTRACT MODE PASS MESSAGE is restored. Next, the game ATTA adjustments are checked and restored to factory settings if an error is found. If y FAIL game adjustments are found intact, the RESTORE high score table is checked for any bad peed entries. Bad entries are replaced with a score of 4,000 points and no initials. If all entries check, the game returns to the

Game Over Mode.GAMEPASS

ADJUSTMENTS?

If game adjustments are restored to y_ FAIL factory settings, the AUDIT TOTALS are checked. If 5 or more audit digits pte

are other than 0-9 (that is hexadecimalSETTINGSSCORELani
A through F) all audit totals are cleared.vENTRIES?

This is followed by a check of the high yf

score table and the table is reset toAUDITS?—__BAD ENTRIES

factory settings if errors are found. en END A

Finally, game adjustments are recheckedYsorunemee ae“INITIALS

and either OPEN COIN DOOR or

FACTORY SETTINGS RESTORED is CLEAR Sener

displayed. With the former, open the INDICATE ALL.

coin door and turn the game OFF and*ad

ON and then FACTORY SETTINGS

RESTORED will be displayed. ReturnHIGHPASS

. < SCORE to game over by depressing the TABLE? ADVANCE pushbutton or by turning FAIL the game OFF and ON a second time. + * RESET HIGH SCORE TABLE ‘TO FACOTRY SETTINGS }-——_

PASS GAME ADJUSTMENTS? i FAIL,

"FACTORY "OPEN COIN DOOR" SETTINGS DISPLAYED RESTORED" DISPLAYED

OPEN COIN

DOOR POWER ON

POWER OFF AND OFF AND ON —~—_ —{— 1 1

“Warning: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever