CATHODE RAY TOMES

Top Gun Parts Catalog (March 1976)

Top Gun (handheld) (Konami, 1989) · Parts Catalog · 22 pages · 9 sections · original scan

Page 1

Midway ene i

TOP GUN

PARTS CATALOG

MIDWAY MFG. CO. ABALLY COMPANY

e 10750 WEST GRAND AVENUE

FRANKLIN PARK, ILLINOIS, 60131, U.S. A.

PHONE: (312) 451-1360 CABLE ADDRESS: MIDCO — TELEX NO.: 72-1596

Page 2

TABLE OF CONTENTS

Page No.

GENERAL INSTRUCTIONS 1

HOLOGRAM SERVICE INSTRUCTIONS 2

LUBRICATION, SWITCH CONTACTS, HOLOGRAM CLEANING 3

HOLOGRAM DRIVE ASSEMBLY A—5

RIFLE & STYLUS ASSEMBLY 6—7

LAMP SHADE ASSEMBLY 8—9

BAR ROOM DOOR ASSEMBLY 10—11

10-90 TIME & 100 SCORE COUNTER ASSEMBLIES 12—13

1-9 TIME & 10-90 SCORE COUNTER ASSEMBLIES 14—15

ADDITIONAL PARTS LIST 16—19

Page 3

GENERAL INSTRUCTIONS FOR “TOP GUN”

  • INSTALLATION:

Remove gun assembly from shipping carton and attach to trigger housing with two provided bolts. Attach four provided cabinet levelers to bottom of cabinet. The power is controlled by a switch located on top of the cabinet. Plug into A.C. only, 60 cycles, 115 voits.

  • VOLTAGE CONTROL:

In low line areas (100 volts or less), an additional boost in the output voltage of the transformer may be obtained by removing the wire from the 115 volt position of the transformer and rewiring to the 100 volt position.

  • COIN CONTROL:

Located on mech panel in back box area and may be set at one coin per play, two coins per play, or two plays per coin by jacking P.C. as indicated on instruction tag on P.C.

  • GAME TIME CONTROL POT:

Located on Program Timer & Discrete Board, {P.C. 0603-00918-8000) Game time may be increased by rotating pot counter-clockwise as pot is viewed from face.

  • SOUND AMPLIFIER VOLUME CONTROLS:

Located on Sound Amplifier Board, (P.C. 0603-00919-8000). To increase volumes rotate pots as indicated below. Clockwise is identified as viewed from pot faces.

A. Hit Sound Volume Control: To increase Hit sound volume, rotate pot clockwise.

B. Master Volume Control: FACE por To increase all sounds, rotate pot clockwise. | Cc C. Cowboy Shot Volume Control: —~ To increase Cowboy Shot Volume, rotate C) pot clockwise. A D D. Player Shot Volume Control: To increase Player Shot Volume, rotate pot clockwise.

  • HOLOGRAM DRUM AND MOTOR ADJUSTMENT:

See separate enclosed instruction sheet.

WARNING

THIS GAME MUST BE GROUNDED. FAILURE TO DO

SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.

Page 4

TOP GUN HOLOGRAM SERVICE INSTRUCTIONS

SKETCH

HOLOGRAM LAMP.

@.

HOLOGRAM MOTOR P.C,

ope

ASSEMBLY & ADJUSTING PROCEDURE

  • All Assembly is from thie rear of the cabinet following is a sequence of assembly of the four (4) module type sub-assemblies which must be followed. A. Insert #2, 3, 4, & #1 in this order. Disassemble in reverse order.
  • Fasten with (2) % - 20 bolts for each module.
  • \f it becomes necessary to replace hologram film which is part of Item #3, first remove module from cabinet. Remove film from pan by removing (3) machine screws located on side of pan. It may be necessary to adjust film after assembly. Follow these instructions: A. — Set the hologram to the position at which the cowboy has the pistol in his holster viewing from the gun mount by turning the hologram by hand (See sketch). B. Loosen (2) set screws {”A”’) of the wiper finger contact. Set contact point to the stop segment of hologram motor p.c, Tighten screws.
  • Replacement of hologram lamp Lamp can be replaced by removing rear door. Simply unscrew from socket & replace. To adjust lamp for maximum reflection, loosen (2) wing nuts (B”) & slide to position at which the cowboy image can be observed most clearly.
Page 5

LUBRICATION

Over-lubrication causes far more trouble in coin-operated equipment than under-lubrication. Practically all cases of poor contact on switches and wiper discs are due to oil or grease, or oi! vapor which forms a film or residue on the contacts and will not allow current to pass through. Excess lubricant may also seep into the clutches, causing them to slip,

IMPORTANT: NEVER USE VASELINE FOR LUBRICATION OF ANY PART OF THE MACHINE. Vaseline is nota true lubricant. It leaves a dirty and gummy residue and it becomes very thick when cold. A special Coin Machine Lubricant is supplied with each machine.

Step-up levers, Ratchets, Cams, Shafts and other sliding or oscillating parts should be very lightly greased with special Coin Machine Lubricant (supplied with machine) not oftener than every six months The bakelite discs on the Motor Units and Step-up Units will require lubrication with the special Coin Machine Lubricant only after the grease is completely evaporated (3-12 months, depending on climate) or when the film of grease becomes dirty. In either event, clean the parts thoroughly with a solvent and a clean soft cloth, then apply an extremely thin coat of the special grease with a fine camel’s hair brush.

Solenoid Plungers should not have a lubricant of any kind. Should there be a sluggish tendency or if plungers are sticking, the parts should be cleaned with a solvent and flaked graphite applied on reassembly.

SWITCH CONTACTS

The contact points, as used on the switches, are generally made of silver which has a high conductivity of electrical current. In some cases, various alloys of silver are used such as a combination of 85% silver, 15% cadmium, 83% silver, 17% cadmium oxide. Certain alloys are used for specific requirements such as high current, low resistance, etc. If point replacement is necessary be sure to replace with the proper equivalent.

Whenever a replacement point is set, it is important that the underside of the point is peened carefully so that it is seated evenly and tightly. This increases the current carrying capacity to its maxium efficiency. A loose point will cause arcing and burning of the blade, eventually the point will fall out. When the contact area of the point becomes dirty, or pitted, a burnishing tool should be used. Filing of the points is not recommended, as the grooves, caused by the file, tend to increase the arcing resulting in a premature short life.

CAUTION

HOLOGRAM CLEANING:

HOLOGRAM MUST BE HANDLED WITH CARE. IF CLEANING IS NECESSARY, USE ISOPROPHL

ALCOHOL SOAKED IN PAPER TOWEL OR SOFT RAG. EXCESSIVE RUBBING OF RAG MUST BE

AVOIDED, EMULSION SIDE OF HOLOGRAM FILM ISON THE INSIDE OF DRUM. AVOID RUBBING

THIS SURFACE IF POSSIBLE.

NOTE: HOLOGRAM WILL ONLY OPERATE WITH A 100 WATT, CLEAR BULB. 110 VOLT
Page 6

NO. 0603 — TOP GUN — HOLLOGRAM DRIVE ASSY.

PAGE 4 MIDWAY MFG. CO,

Page 7

NO. 0603 — TOP GUN — HOLLOGRAM DRIVE ASSY.

iriu] vast we | _oescarrtion | pnee |

0603-00023DRIVE SHAFT ASSY.2.50 EA.

0017-00007-0077 | ROLL PIN — 1/8” x 3/4” .20 EA. 0017-00042-0072 | PLASTIC STANDOFF .20 EA. 0017-00042-0076 | DRIVE GEAR 32-72 1.10 EA. 0017-00104-0047 | WASHER — 1/2” 1.0. x 7/8" 0.D. 1/16" THK. .20 EA.

0603-00011MOTOR MTG. BRKT. ASSY.6.80 EA.

0017-00101-0018 | #6 x 3/4 HEX HD. S.M.S. -20 EA. 0017-00104-0047 | WASHER ~ 1/2''1.0. x 7/8" 0.D. 1/16” THK. 20 EA.

0603-00039WIPER FINGER ASSY.4.10 EA.

0017-00100-0050 | E-RING 1/2” .20 EA. 0017-00101-0308 | #8 — 32x 3/16 SOC. SET SCR. .20 EA.

0603-00908P.C. BOARD6.20 EA.

0017-00007-0075 | ROLL PIN — 1/8" x 5/8” -20 EA.

0040-00615MOTOR23.50 EA.

0017-00042-0118 | GEAR 32-36 1.10 EA.

0603-00024DRUM DRIVE ASSY. COMPLETE54.30 EA.

0603-00012 HOLOGRAM DRUM ASSY. COMPLETE | 592.50 EA.

MIDWAY MFG. CO. PRICES SUBJECT TO CHANGE WITHOUT NOTICE PAGE 5

Page 8

NO. 0603 — TOP GUN — RIFLE & STYLUS ASSY.

MIDWAY MFG. CO.

Page 9

NO. 0603 — TOP GUN — RIFLE & STYLUS ASSY.

| part wo | __DEscRIPTION [price | 0603-00500

PRICES WOOD GUN STOCK

MIDWAY MFG. CO. SUBJECT TO CHANGE WITHOUT NOTICE 42.00 EA.

0518-00138REAR GUN SIGHT-50 EA.
0603-00700BARREL10.90 EA.
0518-00706GUN SUPPORT TUBE19.60 EA.

0017-00102-0003 | 1/4 — 20 x 1/2 (TRUSS HEAD SCREW) .20 EA. 0010-00176-0200 | SPRING .20 EA.

0542-00010TRIGGER ASSY.2.60 EA.

0017-00102-0022 | SOCKET HEAD CAP SCREW 40 EA. 0017-00101-0577 | 6 — 32 x 3/4 PAN HEAD EXT. SEM MSS. .20 EA.

0603-00040TRIGGER SWITCH1.20 EA.
0538-00908TRIGGER HOUSING3.70 EA.

0017-00007-0097 | ROLL PIN .20 EA. 0017-00102-0022 | SOCKET HEAD CAP SCREW 30 EA. 0017-00102-0023 | 1/4 -— 20x 13/4 FLAT HEAD SCREW 40 EA.

0518-00700THRUST BUSHING1.20 EA.
0518-00901PIVOT HOUSING14.10 EA.

0017-00007-0073 | ROLL PIN -20 EA.

0518-00701PIVOT SHAFT50 EA.
0518-00902GUN MOUNT23.50 EA.
0518-00918RUBBER STOP1.50 EA.
21 | 0518-00182RETAINER STOP40 EA.

22 | 0017-00101-0647 | BINDER HEAD SCREW .20 EA.

23 | 0518-00715CONTACT ARM PIN40 EA.

24 | 0017-00100-0025 | E- RING .20 EA. 25 | 0017-00042-0001 | 1/8” CLAMP .20 EA..

26 | 0535-00149PAPER INSULATOR.20 EA.
27 | 0010-00140SPRING.20 EA.

28 | 0017-00100-0025 | E—RING .20 EA. 29 | 0017-00104-0063 | SPRING WASHER .20 EA.

30 | 0518-00122SOLENOID BRACKET ASSY.4.20 EA.

31 | G010-00023-1300 | COIL SOLENOID 5.20 EA.

32 | 0518-00116PIPE BRACKET ASSY.4.20 EA.
33 | 0518-00123END BRACKET-50 EA.

34 | 0553-00021-0400 | STYLUS ARM SWITCH ASSY. 70 EA. 35 | 0017-00100-0025 | E—RING .20 EA. 0017-00100-0025 | E—RING .20 EA.

Page 10

NO. 0603 — TOP GUN — LAMP SHADE ASSY.

MIDWAY MEG. CO.

Page 11

ANAM AFPWrH = NO. 0603 — TOP GUN — LAMP SHADE ASSY.

trem] parr we | vescriprion | Price | 0603-00104 0603-00116 0017-00101-0604 0586-00132 0017-00103-0008 0017-00003-0135 0017-00103-0009 0017-00003-0170 0603-00103 0017-00003-0056 6017-0004 1-0013 _ 0603-00046

0603-00030

PRICES LAMP SHADE “B” LAMP SHADE “A” #8 — 32 x 3/8 EXT. SEM. R.H. M.S. (2) LAMP BRACKET 8 — 32 HEX NUT PROJECTOR LAMP SOCKET #8 — 32 — WING NUT PROJECTOR LAMP 100W CLEAR LAMP MTG. BRACKET & SCREEN LAMP 6V GROMMET LAMP BRACKET & SOCKET ASSY.

COMPLETE LAMP SHADE ASSY.

MIDWAY MFG. CO. SUBJECT TO CHANGE WITHOUT NOTICE 1.60 EA. .80 EA. .20 EA. 40 EA. .20 EA. 1.50 EA. .20 EA. 1.10 EA. 5.50 EA. .20 EA. .20 EA. .60 EA.

20.00 EA.

Page 12

NO. 0603 — TOP GUN — BAR ROOM DOOR ASSY.

MIDWAY MFG. CO.

Page 13

NO. 0603 — TOP GUN — BAR ROOM DOOR ASSY.

frau rant we | _vesenretion ——__‘|_mer | 0010-00577 EXTENSION SPRING 0017-00100-0018 jE-—RING 0603-00109 LINK, DOOR OPENER 0603-00132 SPRING BRACKET 0017-00007-0073 + =|ROLL PIN 1/8 DIA. 7/16” ROLL PIN 0603-00117 SOLENOID LINK 0603-00006 PIVOT BRACKET LEFT SUB. ASSY. 0603-00010 SOLENOID LINK ASSY. 0603-00007 PIVOT BRACKET RIGHT SUB. ASSY. 0017-00007-0061 j|ROLL PIN 0603-00017 SOLENOID & DOOR SUPPORT BRACKET ASSY. 0022-00001 STOP BRACKET SUB. ASSY. 0064-030X X-XXDX |1N — 4004 DIODE 000V-00023-0800 {COIL 0022-0200-0003 |SOLENOID COIL STOP BRACKET 0010-00578 COMPRESSION SPRING 0603-00702 COIL PLUNGER 0603-00107 SOLENOID BRACKET 0017-00031-0027 |SOCKET 0017-00003-0052 |LAMP 12V (4) 0017-00101-0694 |BINDER HEAD SCREW 4 — 40 x 5/16 0017-00104-0006 {#4 WASHER 0603-00044 BAR ROOM DOOR ASSY. 0603-00701 ROD 0603-00108 BAR ROOM DOOR SUPPORT BRACKET 0017-00031-0011 KH COMO AN]HDMTM PWN =

0603-00134DOOR STOP BRACKET40 EA.
0603-00130DOOR STOP.20 EA.
0603-00009PIVOT BRACKET & ROD ASSY. LEFT4.00 EA.
0603-00008PIVOT BRACKET & ROD ASSY. RIGHT2,70 EA.
0603-00913BAR ROOM DOORL&R9.20 EA.
0603-00031BAR ROOM DOOR ASSY. COMPLETE36.70 EA.

MIDWAY MFG. CO. PRICES SUBJECT TO CHANGE WITHOUT NOTICE PAGE 11

Page 14

NO. 0603 — TOP GUN — 10-90 TIME & 100 SCORE & TIME COUNTER ASSY.

CHECK PRICE LIST FOR ADDITIONAL PARTS.

MIDWAY MFG.CO.

Page 15

NO. 0603 — TOP GUN — 10-90 TIME & 100 SCORE & TIME COUNTER ASSY.

DESCRIPTION

3” COUNTER ASSY. 0017-00009-0281 | (10-90 SCORE) 0017-00009-0283 | 3” COUNTER ASSY. (100 SCORE & TIME) 20.20 EA. 23.50 EA.

MIDWAY MFG. CO. PRICES SUBJECT TO CHANGE WITHOUT NOTICE PAGE 13

Page 16

NO. 0603 — TOP GUN — 1-9 TIME & 10-90 SCORE COUNTER ASSYS.

CHECK PRICE LIST FOR ADDITIONAL PARTS.

PAGE 14 MIDWAY MFG.CO.

Page 17

NO. 0603 — TOP GUN — 1-9 TIME & 10-90 SCORE COUNTER ASSYS.

rem partr.no | pescriprion | PRCE 0017-00009-0282 | 3” COUNTER ASSY. 21.00 EA. (1-9 TIME) 0017-00009-0281 | 3” COUNTER ASSY. 20.20 EA. (10-90 SCORE)

MIDWAY MFG. CO. PRICES SUBJECT TO CHANGE WITHOUT NOTICE PAGE 15

Page 18

NO. 0603 — TOP GUN — ADDITIONAL PARTS LIST

0603-00915 0017-00009-0014 0603-00028 0603-00027 0603-00026

0603-00018 0603-00021 0603-00713 0603-00013 000A-00025-1150 0022-00200-0003 0022-00001 0512-00702 0603-00909 0017-00007-0079 0010-00178 0017-00100-0018 0603-00905 0603-00142 0603-00911

0603-00016 0603-00019 0603-00710 0603-00013 000A-00025-1150 0022-00200-0003 0022-00001 0512-00702 0603-00909 0017-00007-0079 0010-00178 0017-00100-0018 0603-00903-0100 0603-00911

PAGE 16 prices DESCRIPTION PRICE

PLAYFIELD SCENERY SPRING BOLT (4) WATER TROUGH TARGET ASSY. BARREL TARGET ASSY. DOORWAY TARGET ASSY. WATER TARGET ASSY. WATER TARGET MTG. PLATE ASSY. WATER TARGET PINNING ASSY. TARGET SHAFT LEVER SUB. ASSY. coIL STOP BRACKET STOP BRACKET SUB. ASSY. PLUNGER LINK ROLL PIN SPRING “E” RING WATER TARGET WATER TARGET STIFENER DAMPENER DOOR TARGET ASSY. DOOR TARGET MTG. PLATE SUB. ASSY. DOOR TARGET PINNING ASSY. TARGET SHAFT LEVER SUB. ASSY. COIL “A” TYPE STOP BRACKET STOP BRACKET ASSY. PLUNGER LINK ROLL PIN 1/8 x 1" LG. SPRING “EB” RING DOORWAY TARGET DAMPENER

MIDWAY MFG. CO. SUBJECT TO CHANGE WITHOUT NOTICE 17.20 EA. 1.10 EA. 21.30 EA. 20.00 EA. 19.40 EA.

4.70 EA. 9.30 EA. 1.40 EA. 1.80 EA. 2.80 EA. -30 EA. 1.00 EA. 1.20 EA. -20 EA. -20 EA. .20 EA. .20 EA. 3.60 EA. -20 EA. -20 EA.

4.40 EA. 7.60 EA. 1.20 EA. 1.80 EA. 2.80 EA. -30 EA. 1.00 EA. 1.20 EA. .20 EA. -20 EA. .20 EA. -20 EA. 3.60 EA. .20 EA.

Page 19

NO. 0603 — TOP GUN — ADDITIONAL PARTS LIST

rem[ part wo | _ Description | price | BARREL TARGET ASSY. 0603-00014 BARREL TARGET MTG. PLATE S/ASSY. 0603-00020 BARREL TARGET PINNING ASSY. 0603-00710 TARGET SHAFT 0603-00013 _| LEVER SUB. ASSY. 000A-00025-1150 | COIL 0022-00200-0003 | STOP BRACKET 0022-00001 STOP BRACKET ASSY. 0512-00702 PLUNGER 0603-00909 LINK 0017-00007-0079 | ROLL PIN 1/8 x 1" LNG. 0010-00178 SPRING 0017-00100-0018 | “E” RING 0603-00903-0200 | BARRELL TARGET 0603-00911 DAMPENER CONTACT ARM ASSY. 0603-00123 CONTACT ARM 0538-00132-0001 | CLEVIS 0017-00006-0005 | BUSHING 0017-00071-0024 | EYELET 0017-00072-0034 | RIVET 0568-00155 SW. BRACKET 0603-00015 CONTACT ARM ASSY. (COMPLETE) RIVET BOARD STYLUS HARDWARE 0603-00025 RIVET BOARD PLATE ASSY. 0540-00138-0014 | (CABLE PROTECTOR)-(SUPPORT BAR PROTECTOR) 0603-00912 RIVET BOARD 0603-00045 RIVET BOARD ASSY. BACKGROUND SCENERY BD ASSY. 0603-00910-0100 ; (LEFT) BUTYRATE WINDOW TARGETS 0603-00910-0200 | (RIGHT)BUTYRATE WINDOW TARGETS 0603-00032 CARD & HIT INDICATOR ASSY. 0603-00916 LITE SHIELD (2) FINAL ASSY. 0603-00140 PLEX SUPPORT BRACKET (FOREIGN) MIDWAY MFG. CO. PRICES SUBJECT TO CHANGE WITHOUT NOTICE PAGE 17

Page 20

NO. 0603 — TOP GUN — ADDITIONAL PARTS LIST

0603-00914-0100 | PLEX SCORE (FOREIGN) 45.60 EA.

0603-00901SIDE SCENERY — LEFT4.60 EA.
0603-00902SIDE SCENERY — RIGHT4.60 EA.
0603-00914SCORE GLASS32.60 EA.
0603-00906MIRROR 26 1/4 x 17 1/16 x 1/422.40 EA.

0537-00903-0028 | CYCOLAC GLASS EDGING 26 3/16 -50 EA. 0537-00903-0027 | CYCOLAC GLASS EDGING 20 13/16

  • .80 EA. 0017-00102-0048 | LEG LEVELERS (4) -50 EA. 0017-00103-0026 | LEG LEVELER NUTS 3/8 - 16 (4) .20 EA.
0603-00139FISHPAPER CABLE STRAPS (6).20 EA.

0090-00020-02BR | FRONT DOOR ASSY. 104.00 EA. 0090-00002-02BR | FRONT DOOR FRAME 7.80 EA.

0572-00103VENT GRILL1.20 EA.
0547-00035SPEAKER BEZEL2.00 EA.

0017-00003-0161 | 4” SPEAKER 6.00 EA.

0549-00128SPEAKER GRILL-70 EA.

0017-00041-0576 | SPEAKER GASKET .20 EA. 0017-00003-0102 | COUNTER 9.00 EA. 0537-00138-0001 | 26” GLASS LIFT CHANNEL 2.60 EA.

0014-00101DOOR LOCK PLATE40 EA.

0017-00005-0051 | LOCK PLATE -40 EA. 0017-00005-0046 | LOCKS (1350) 3.40 EA. 0017-00009-0033 | CLAMP (2) 1.20 EA.

0603-00131STRIKE (2)-40 EA.

0603-00037 FLOURESCENT REFLECTOR ASSY. COMPLETE W/O BL-BULB 20.00 EA. 0017-00003-0110 | 24” FLOURESCENT LAMP (F20T12-BL) 7.00 EA.

0603-00133FLOURESCENT BRACKET2.60 EA.
0548-00137FLOURESCENT HOLDER BRACKET40 EA.

0017-00003-0019 | FLOURESCENT STARTER -20 EA. 0017-00021-0079 | FLOURESCENT STARTER HOLDER 2.00 EA. 0017-00003-0026 | BALLAST 4.40 EA. 0017-00031-0015 | FLOURESCENT LAMP SOCKETS .60 EA. 0017-00041-0013 | GROMMET .20 EA. MIDWAY MFG. CO. PAGE 18 PRICES SUBJECT TO CHANGE WITHOUT NOTICE

Page 21

NO. 0603 — TOP GUN ~ ADDITIONAL PARTS LIST

irew[ rart we | pescniprion nice | 0549-00141 0017-00009-0009 0566-00120 0566-00121 0601-00010 0017-00101-0576 0017-00031-0002 0017-00003-0052 0017-00009-0165 0017-00009-0167 0017-00009-0166 0539-00135 M645-00216 0603-00917 0603-00918 0603-00919

PRICES GLASS LOCK BRACKETS TURN BUTTON COIN BOX COIN BOX COVER CASH BOX LOCK BRACKET CARRIAGE BOLTS SOCKETS LAMPS #1895 2 POSITION BRACKET DUMMY BRACKET 2 POSITION BRACKET BACK DOOR RETAINER P.C. PROGRAM UNIT MOTOR SPEED PROGRAM TIMER SOUND AMPLIFIER BRD.

MIDWAY MFG. CO. SUBJECT TO CHANGE WITHOUT NOTICE 1.30 EA. -20 EA. 6.00 EA. 2.20 EA. 1.40 EA. .20 EA. .20 EA. 0 EA. -70 EA. 1.10 EA. -60 EA. .90 EA. 1.00 EA. 46.00 EA. 52.00 EA. 72.00 EA.

Page 22

NOTES

This space is provided for personal notes

MIOWAY MFG. CO.