Canyon Bomber TM-097 2nd Printing
Canyon Bomber (Atari, 1977) · Technical Manual · 76 pages · 25 sections · original scan
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
GAME SERIAL NUMBER LOCATION
Your game’s serial number is stamped on the circuit (back) side, bottom right corner, of the printed circuit board—see the illustration below. The same number is also stamped on the TV monitor chassis and on the label located on the rear of the game cabinet. Please mention this number whenever calling your distributor for service.
fee) ‘ON 3WY9,
Canyon Bomber’
Operation, Maintenance and Service Manual
Complete with Illustrated Parts Catalog
ATARI INC 1265 BORREGAS AVENUE RO. BOX 9027 SUNNYVALE, CALIFORNIA 94086 408/745-2000 « TELEX 35-7488
A,
ATARI
A Warner Communications Company
All rights reserved. Copyright © 1977 by Atari, Inc. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher.
For permission requests, write:
ATARI INC 1265 BORREGAS AVENUE RO. BOX 9027 SUNNYVALE, CALIFORNIA 94086
nF
Lithographed in the U.S.A.
TABLE OF CONTENTS
1 LOCATION SETUP INTRODUCTION .. Game Operation Owner Options and Self-Test Physical Description B, GAME INSPECTION C. INSTALLATION REQUIREMENTS ... Power Requirements and Line Voltage Selection Temperature Range Humidity ........... Location Space Requirements Type of Power Cord ... INTERLOCK AND POWER ON/OFF SWITCHES OPERATOR OPTIONS .... SELF-TEST PROCEDURE VOLUME CONTROL
2 GAME PLAY A. ATTRACT MODE B. READY-TO-PLAY MODE C. PLAY MODE
3 MISTS TENANCE AND ADJUSTMENTS CLEANING ANWWNNNKANNKNNNAN AA ammo
z COIN MECHANISM .. 10 Components on Coin Door 70 Access to Coin Mechanisms . 10 Cleaning of Coin Paths ..... 11 Adjustment of Coin Switch Trip Wire . 12 Mechanical Adjustments on Coin Mechanism 12 General Troubleshooting Hints C. FUSE REPLACEMENT ... D. LAMP REPLACEMENT .. Fluorescent Lamp Replacement Procedure . Fire Button Replacement Procedure .. E, TV MONITOR REMOVAL F. TV MONITOR ADJUSTMENTS G. LED START SWITCH REPLACEMENT ..
4 THEORY OF OPERATION A. GENERAL INFORMATION B. COMPONENTS OF THE MICROCOMPUTER SYSTEM . Program Memory .... Read/Write Memory Microprocessing Unit Tri-State Devices
TABLE OF CONTENTS
C. MICROCOMPUTER SYSTEM
m Program Memory Enable RAM ENABLE ........ Phase 1 and Phase 2 . RAM Output .......... MICROCOMPUTER WATCHDOG .. COMPONENTS OF CANYON BOMBER GAME CIRCUITRY ... System Clock and Sync Generator ... Playfield Generator .. Motion Generator ... Video Output Manual Control Interface . Motor Generator Whistle Generator . Audio Output
5 ILLUSTRATED PARTS CATALOG
LIST OF ILLUSTRATIONS
Figure 1-1 Location of Voltage-Changing Plug 3 Figure 1-2 Location of On/Off, Interlock, and Self-Test Switches . 4 Figure 1-3 Location of Volume Adjustment ............-+++ 6 Figure 2-1 Attract Mode ......... Figure 2-2. Ready-To-Play Mode Figure 2-3. Play Mode ........... Figure 3-1 Coin Door Assembly .........-..00. 00 ee eee Figure 3-2. Hinging Open the Magnet Gate Assembly Figure 3-3 Removal of Coin Mechanism Figure 3-4 Surfaces to Clean Inside the Coin Mechanism ... Figure 3-5 Removal of Plate Covering Rear of Coin Slot Figure 3-6 Close-Up View of Lubrication Point ...... Figure 3-7 Detail View of Coin Switch and Trip Wire . Figure 3-8 Securing the Coin Switch Trip Wire Figure 3-9 | Adjustments on Coin Mechanism . Figure 3-10 Lamp and TV Monitor Removal Figure 3-11 Locations of Adjustments on TV Chassis Figure 3-12 LED Start Switch Replacement Figure 4-1 Game Block Diagram Figure 4-2. Canyon Bomber PCB Block Diagram . Figure 4-3 Phase 1 and Phase 2 Signal Shaping . Figure 4-4 RAM Write Enable Signal Shaping ... Figure 4-5 Playfield Generator Character Trace for the Letter “C” Figure 4-6 TV Monitor Display : Figure 4-7 TV Monitor Schematics Figure 4-8 | Canyon Bomber Schematic Diagram (5 sheets) Figure 4-9 _ Harness Schematic
ILLUSTRATED PARTS CATALOG
Figure 5-1 Canyon Bomber Final Assembly .......+ 0000 cce cece teen ee eee eens Figure 5-2. Power Supply Assembly ... Figure 5-3 Control Panei Assembly . Figure 5-4 Fire Button Assembly Figure 5-5 — Fluorescent Light Assembly Figure 5-6 TV Shelf Assembly .... Figure 5-7 Coin Door Assembly .. Figure 5-8 RF Shield PCB Assembly . Figure 5-9 Canyon Bomber PCB Assembly ..
LIST OF TABLES
Table 1-1 | Operator Options ... Table 1-2 Self-Test Procedure Table 4-1 Approximate Base Voltage of Transistor Q1 and Q2 for Given Address
vi
Af A. INTRODUCTION Game Operation Atari’s Canyon Bomber™ is a computercontrolled, black-and-white TV monitor game for one or two players. The game simulates the flight of vintage warplanes and blimps in bombing runs across a canyon filled with targets. The targets are hundreds of bubbles, each displaying a point value from one through four. The player controls a bomb release from his or her aircraft. The altitude is controlled by the computer and varies at random with each bomb run. Falling bombs and detonations are accompanied by realistic sound effects while targets are destroyed to a depth of four to eight layers. ee.
LOCATION SETUP .
As targets are destroyed, accumulated points are displayed and gaps develop in the target area. If a bomb falls into a gap or outside the canyon, amiss is registered. A miss is also registered if no bomb is dropped during the pass of an aircraft. Game play ends when each player accumulates a certain number of misses. During play, the number of misses remaining is continuously displayed. The miss limit can be three, four, five, or six, as selected by internal switches. The object of the game is to destroy all targets before reaching the miss limit. If all targets are destroyed, the canyon is refilled with targets, play continues, and the remaining misses stay the same. The canyon can be refilied a maximum of four times. Game play is described in detail in Chapter 2.
Owner Options and Self-Test In addition to permitting the selection of miss limits, internal switches provide for selecting the number of coins per player and for the display fanguage (English, French, German, or Spanish). A selftest feature permits a quick check of all controls the TV monitor, and related circuits. Tabies 1-1 and 1-2 in this chapter direct the option-select and selftest procedures.
Physical Description Major components of the game are the TV monitor, printed circuit board (game PCB), power supply, coin mechanisms, and coin box. The TV monitor is accessible for adjustments through a removable service panel, secured by four screws and located at the rear of the monitor compartment of the cabinet. The TV monitor is removable from the front. (Refer to Figure 3-10 in Chapter 3.) All other major components are accessible through the rear door, which has an interlock switch that disables AC power input. The coin door permits access to the self-test switch as well as to the coin mechanisms and coin box.
The PCB fits into a shielded enclosure. The PCB connector is secured to a removable end plate (RF or radio frequency shield) of the enclosure, and is hard-wired to the harness. The PCB is accessible when the RF shield is removed. The RF shield is secured by ten screws. The option switches and volume controls are located on the PCB. A power switch is located on the top right side of the cabinet. The switch permits power to be shut down without opening the cabinet or pulling the power cord from the outlet. B. GAME INSPECTION Examine the game carefully for evidence of any shipping damage. Check the outside of the cabinet for dents, chips, or broken parts. Open the rear access door and check for anything that appears broken or out of place.
C. INSTALLATION
REQUIREMENTS
Power Requirements and Line Voltage Selection (See Figure 1-1) The game is shipped for operation at 110 VAC, 60 Hz. Power consumption is approximately 150 watts. At the power supply, line voltage operation is determined by selecting one of four connectors and plugging it into the voltage selection socket. Figure 1-1 shows the four connectors, with one of them plugged in, The piugs are identified by wire color as listed in Figure 1-1. Note that there are two basic operating voltages—110 VAC, 60 Hz and 220 VAC, 50 Hz, with provisions for low line voltage in each case. To insure proper operation, measure line voltage. If voltage is below 100 V (for 110 VAC lines) or below 210 V (for 220 VAC lines), use the low voltage connections.
Temperature Range Operation or storage—32° to 120° Fahrenheit (0° to 49° Celsius)
Humidity Operation or storage—95% maximum, with no condensation
Location Space Requirements Vertical Clearance—185 centimeters (73 inches) Width—75 centimeters (29.5 inches) Depth Clearance, including Player Space— 61 centimeters (24 inches)
Type of Power Cord Atari has added a strain relief power cord to Canyon Bomber. The advantage of this type of power cord is that, if pulled accidentally, the strain relief will hold the cord in place at the cabinet wall. The plastic strain relief “cushions” the impact of the shock and prevents the cord from pulling the wires out of the harness connector.
D. INTERLOCK AND POWER ON/OFF SWITCHES To minimize the hazard of electrical shock while you are working inside the game cabinet, an interlock switch has been installed at the rear access door. This
LINE VOLTAGE-CHANGING VOLTAGE PLUG WIRE COLOR 95 VAC | BLACK 110 VAC ORANGE (installed _at factory) 210 VAC GREEN [__ 220 VAC RED al
On/Off and
C4 Interlock
Switches
e| G&
3 Amp, 250 V. Slow-Blow
8 Amp, 125 V. Fast-Blow
Figure 1-1
switch removes all power from the game while the access door is open.
To help you conserve energy, a power on/off switch has been installed on the Canyon Bomber game so that it can be turned off during closed periods. Refer to Figure 1-2 for switch locations.
Please check for proper operation of the rear access door interlock switch by performing the following steps:
- Unlock and open the rear access door.
- Plug the AC power cord into a power source (wall plug).
- Set the power on/off switch to the on position. Location of Voltage-Changing Plug
- Close the rear access door. Within approximately 30 seconds the TV monitor should display a picture.
- Slowly open the rear access door until the picture on the TV monitor disappears. The picture should disappear when the rear access door is opened less than one inch from the top.
- If the results of Step 5 are satisfactory, the interlock switch is operating properly. If the picture does not disappear as described, check to see if the switch is broken from its mounting or stuck in the on position.
- Close and lock the rear access door.
E. OPERATOR OPTIONS Options of the Canyon Bomber game offer the operator maximum player appeal for each game loca-
Self-Test Switch
UE Power On/Off Switch
|_——— Interlock Switch
Figure 1-2 Location of On/Off, Interlock, and Self-Test Switches
tion. These options are listed in Table 1-1. They are preset for a certain game structure while being manufactured. To determine how the switches have been set for your game, check the viewing screen during the attract mode, and compare with the information in Table 1-1.
In order to change the toggle positions of the switch assembly and thus set the desired options, the printed circuit board (PCB) must be removed according to the following procedure:
- Unplug the game. Unlock and open the rear access door.
- Locate the RF shield assembly immediately inside the cabinet on the right. (It is an aluminum box with small holes.) On one end of the box is a printed circuit board with an edge connector coming from the edge of the board. This printed circuit board is the RF shield assembly.
. Remove the five pan-head Phillips screws from each of the long sides (total of ten screws) of the RF shield assembly.
. Carefully remove the PCB from the RF shield assembly.
Table 1-1 Operator Options
Switch Settings
| Option | 8 | 7 | 6 | 5 | 2 | q | Result |
| Game Cost | OFF | ON | One Coin Per Player | ||||
| OFF | OFF | Two Coins Per Player | |||||
| ON | OFF | Two Players Per Coin | |||||
| ON | ON | Free Play | |||||
| Misses Per Play | ON | ON | Three | ||||
| ON | OFF | Four | |||||
| OFF | ON | Five | |||||
| OFF | OFF | Six | |||||
| Language | ON | ON | English | ||||
| OFF | ON | French | |||||
| ON | OFF | Spanish | |||||
| OFF | OFF | German |
- Set the switches for the desired options, as shown in Table 1. (Note that switches 3 and 4 are not used.)
- Reinstall the PCB following steps 1 through 4 in reverse order. Do not force or bend the printed circuit board. Before reinstalling, always inspect the printed circuit board for damage. Close and lock the rear access door.
- Plug in the game and verfiy option functions by playing it. F. SELF-TEST PROCEDURE (See Table 1-2) The self-test procedure permits you to check the TV monitor, the character-generating and sync circuits, and the controls. The procedure uses the TV monitor itself and the speakers; no additional equipment is required. We suggest that you run the self-test each time the coin box is emptied.
Table 1-2 Self-Test Procedure
Instruction Results if Test Passes Results if Test Fails
Unlock and open Coin Door. Set self-test slide switch (located inside and at center of the Coin Door) to the on position. TV monitor displays the entire character set in a repeating black and white pattern. Character set is not displayed on TV monitor.
2 Press all player control Falling-bomb sound should be Absence of falling-bomb sound. buttons individually (including coin switches, fire buttons, LED switches, and RESET button).
Close contacts of the coin door slam switch. produced for each operation of a button. If test Step 1 was normal and only one control fails to produce the correct sound, the trouble is probably in that control button.
Falling-bomb sound should be produced each time the slam switch contacts are closed. sound. Absence of falling-bomb
G. VOLUME CONTROL If volume is incorrect for your location, remove There are three modes of operation: attract the game PCB and adjust the volume control. See (power applied), ready-to-play (coins accepted), and Figure 1-3. play (one or both START buttons pressed).
RIGHT SPEAKER: VOLUME
LEFT SPEAKER VOLUME
Figure 1-3 Location of Volume Adjustment
A. ATTRACT MODE In the attract mode, a canyon filled with targets is displayed and the aircraft fly across the screen at random intervals and altitudes. The TV monitor displays a black blimp, eventually replaced by an airplane, and a white blimp, also replaced by an airplane. Across the top of the screen appears BLACK SCORE and HIGH SCORE in black letters and WHITE SCORE and HIGH SCORE in white letters. The black and white scores are the scores of the last game played. Upon initial power-up all scores are zero. The high score displays indicate the highest game score, forthat color, that has been recorded since the HIGH SCORE RESET button was set.
A line of information appears in black lettering. The line alternately flashes the coins per play (internally selected), and the misses per play.
B. READY-TO-PLAY MODE When one coin has been deposited (assuming one coin per player), a second message line reads YOU HAVE 1 CREDIT. This information flashes alternately with another message, PUSH START BUTTON. The number of credits indicated is determined by the number of coins deposited, the coins per player, and the plays remaining. Each player uses one credit per play. A maximum of four coins can be deposited. Either coin slot may be used.
C. PLAY MODE If one coin has been deposited (assuming one coin per player), the game begins as a single-player game when either START button is pressed. If two or more coins are deposited (in either or both coin slots), a four-second delay (freeze mode) occurs
Figure 2-1 Attract Mode
Figure 2-2 Ready-To-Play Mode Figure 2-3 Play Mode
when one START button is pressed. If the other START button is pressed within four seconds, the game starts as a two-player game, with each player controlling a bomb release for his or her aircraft. If the other START button is not pressed within four seconds, the game starts as a single-player game. As a single-player game, the player controls the bomb release for the color of aircraft associated with the START button that was activated. The computer controls the other.
Play begins with blimps flying by. After a period of time, planes instead start flying by. (Blimps fly at higher altitudes, but fly slower than the planes.) For either type of aircraft, abomb must land and explode before another can be released.
Play continues until the miss limit.is reached by each player. When there is only one player, the game continues until he or she has reached the miss limit, even though the computer-controlled aircraft might have reached the miss limit. If a player hits all targets in the canyon, the canyon refills with targets, but the remaining misses stay the same. The canyon can be refilled a maximum of four times per game. During play, MISSES LEFT is indicated in place of each HIGH SCORE display. After each game, the HIGH SCORE display returns, indicating the highest game score since power was applied to the unit. The HIGH SCORE RESET button may be used to clear the display to zero.
Due to its solid-state electronic circuitry, this Atari unit should require very little maintenance and only occasional adjustment. Information given in this chapter and elsewhere in this manual is intended to cover most servicing situations that may be encountered at the game site. The procedures given are in sufficient detail to be understood by a person with moderate technical background.
lf reading through this manual does not lead to solving a specific maintenance problem, you can reach Atari's Customer Service Department by telephone Monday through Friday, from 7:30 a.m. to 4 p.m. Pacific Time. From California, Alaska and Hawaii, call (408) 984-1900; from the remaining 47 states call (800) 538-6892 (toll-free).
If you are interested in gaining more information on video game technology, especially the electronics, we recommend reading the Video Game Operator’s Handbook, manual number TM-043. This book is available from Atari, Inc., Attn. Customer Service Department, 2175 Martin Avenue, Santa [ca CA 95050 for $5 each, or from your distributor.
ADJUSTMENTS
A. CLEANING
The exteriors of game cabinets and plex panels may be cleaned with any non-abrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Donot dry-wipe the plex panels because any dust can scratch the surface and results in fogging the plastic.
B. COIN MECHANISM
Components On Coin Door Figure 3-1 shows the back side of the coin door assembly where the game’s two coin mechanisms are mounted, Included is the lock-out coil assembly; the lock-out wires are connected to this assembly but are hidden behind the coin mechs. During the attract mode the microcomputer energizes the lockout coil, causing the lock-out wires to retract far enough to allow genuine coins to reach the coin box. But during the ready-to-play mode when the LED is lighted and during the play mode (and also when AC power to the game has been turned off)
Slam Switch Assembly
Lamp Holder
Figure 3-1 Coin Door Assembly the lock-out coil is de-energized, causing the lockout wires to move out far enough to divert coins over to the return chute.
Directly below each coin mechanism is a secondary coin chute and a coin switch with a trip wire extending out to the front edge of the chute. When the trip wire is positioned correctly, a coin passing down the secondary chute and into the coin box will momentarily push the trip wire down and cause the switch contacts to close.
Also shown in the photograph is a slam switch assembly. It has been included to defeat any players who might try to obtain free game plays by violently pounding on the coin door to momentarily close the contacts on a coin switch. The slam switch contacts connect to the microcomputer system, which will ignore coin switch signals whenever the slam switch contacts are closed.
Access To Coin Mechanisms To remove jammed coins, and for maintenance cleaning, each magnet gate assembly can be hinged open without removing it from the door, as shown in Figure 3-2, Or, ifnecessary, each coin mechanism can be entirely removed from the door merely by pushing
Figure 3-2 Hinging Open the Magnet Gate Assembly
down on a release lever and simultaneously tilting the mechanism back, then lifting it up and out. This is shown in Figure 3-3.
(Clean both surfaces where coin enters the mechanism, as well as the magnet)
Figure 3-4 Surfaces to Clean Inside the Coin Mechanism
Figure 3-3 Removal of Coin Mechanism
Cleaning of Coin Paths
—————-— CAUTION The use of an abrasive (such as steel wool ora wire brush) or a lubrication on a coin mechanism will result in a rapid buildup of residue.
By talking to many operators, we have found that the best method of cleaning a coin mechanism is by using hot or boiling wateranda mild detergent. A toothbrush may be used for those stubborn buildups of residue. After cleaning, flush thoroughly with hot or boiling water, then blow out all water with compressed air.
Figure 3-4 shows the surfaces to clean inside the coin mechanism. These include the inside surface of the mainplate, and the corresponding surface of the gate assembly. There may also be metal particles clinging to the magnet itself. To remove these youcan guide the point of a screwdriver or similar tool along the edge of the magnet.
If coins are not traveling as far as the coin mechanisms, you will need toclean the channel beneath the coin slot. To gain access to this channel, use a %-inch wrench and remove all three nuts that secure the cover plate (refer to Figure 3-5), Removing the plate will provide access to the entire channel. Figure 3-5 Removal of Plate Covering Rear of Coin Slot
Also clean the inside surfaces of the secondary coin chutes, but when doing this be careful not to damage or bend the trip wires on the coin switches.
Lubrication Do not apply lubrication to the coin mechanisms. The only points that may need lubrication (and only rarely) are the shafts of the scavenger buttons (coin rejection buttons) where they pass through the coin door. Apply only one drop of light machine oil, and be positive that no oil drops down onto a coin mechanism. Figure 3-6 shows this Subrication point.
W
Manually hold down rejection button and apply one drop here.
Lock-out Wire
Figure 3-6 Close-Up View of Lubrication Point
Adjustment of Coin Switch Trip Wire In order for a coin switch to operate reliably when a coin travels down the secondary coin chute, the rest position of its trip wire should be as shown in Figure 3-7. Use extreme care when handling or touching these wires.
Three problems can occur with trip wires—they can be too long, too short, or become loosened and fall off.
With a wire that is too long, you may have a problem of catching it on the opening in the cash box as a coin is accepted. You can cut off the end of the wire in small increments, making sure it still extends slightly through the ““V” of the coin chute.
If the trip wire is too short (either by wrong adjustment or by being cut off too much), coins may slip by the wire without tripping it, and no credits will be given. The solution is to carefully bend and straighten out the wire to lengthen it. If you cannot straighten it sufficiently, contact your distributor to order another trip wire.
If the wire is loose and falls off its mounting stud, it will also cause no credits to be given. Secure the wire by crimping together both ends of the brass- Correctly adjusted trip wire
Figure 3-7 Detail View of Coin Switch and Trip Wire
Crimp together mounting stud at 2 arrows shown. | Figure 3-8 Securing the Coin Switch Trip Wire
colored mounting stud with a pair of pliers (see Figure 3-8). If you should ever need to remove the trip wire, the two halves of the mounting stud can be separated with a small screwdriver.
Mechanical Adjustments on Coin Mechanism Coin mechanisms are adjusted prior to shipment from the factory and normally will retain these adjustments for many months. If, due to wear or other causes, it becomes necessary to make new adjust-
ITEM IDENTIFICATIONS 1 Kicker and Separator Screws 2 Washers 3 Kicker 4 Separator 5 Gate Lever Spring 6 Gate Pivot Pin 7 Mainplate Assembly 8 “C” washer 9 Rail 10 Gate Assembly 12 Cradle Assembly
o~ 13 Upper Gate Pivot Spring 14 Undersize Lever Assembly 15 Magnet Gate Assembly 16 Magnet Gate Adjuster 17 Retaining Screws 18 Coverplate Assembly 19 Return Coverplate 20 Coverplate 21 Mounting Studs 22 Lower Gate Pivot Spring 23 Coin Release Lever
Kicker and separator
- Set the acceptor with the back of the unit facing you in the test position.
- Loosen the kicker and separator screws (1) and move the kicker (3) and the separator (4) as far to the right as they will go. Lightly tighten the screws.
- Insert several test coins (both old and new) and note that some are returned by striking the separator.
- Loosen the separator screw and move the separator a slight amount to the left. Lightly retighten the screw.
- Insert the test coins again and, if some are still returned, repeat Step 4 until all the coins are accepted.
- Loosen the kicker screw and move the kicker as far to the left as it will go. Lightly retighten the screw.
- Insert the test coins and note that some are returned.
- Loosen the kicker screw and move the kicker a slight amount to the right. Lightly retighten the screw.
- Insert the test coins again and, if some are still returned, repeat Step 8 until all the coins are accepted.
- Be sure that both screws are tight after the adjustments have been made.
Magnet gate . Set the acceptor with the front of the unit facing you in the test position. . Turn the magnet gate adjusting screw (16) out or counterclockwise until none of the coins will fit through. |. With a coin resting in the acceptor entrance, turn the adjuster in or clockwise until the coin barely passes through the magnet gate. . Test this adjustment using several other coins (both old and new) and, if any fail to pass through the magnet gate, repeat Step 3 until all the coins are accepted.
- Fix the magnet gate adjusting screw in this position with a drop of glue. Ro
Boe
Additional Cleaning
- Remove the transfer cradle (12) and the undersize lever (14).
- Use a pipe cleaner or similar effective cleaning tool to clean the bushings and pivot pins.
- Replace the transfer cradle and the undersize lever.
- To be certain the coin mechanism is completely free of any residue, place the mechanism in boiling water for several minutes. Carefully remove it and let it ai reinstalling in the door.
Figure 3-9 Adjustments on Coin Mechanism
ments, remove the coin mechanism from the coin door. Then take it to a clean, well lighted area where it can be placed in a vertical position on a level surface (such as a bench top). Besides a screwdriver, you will need several coins, including both newand old, worn ones. Figure 3-9 shows an exploded view of the mechanism and gives procedures for adjusting the kicker, separator, and the magnet gate. These adjustments should only be done by someone with experience in servicing coin mechanisms and who understands their operation.
General Troubleshooting Hints The first action is to look for jammed coins. After these have been removed, examine the coin path for presence of foreign material or loose objects (such as chewing gum, small metallic objects, paper wads, etc.). In cases where game usage is heavy, it may be necessary to clean the entire coin path periodically, in order to prevent build-up of contaminants that can hinder the movement of coins through the mechanisms. Also confirm that the trip wire on each coin switch is intact, and is properly adjusted. If troubles still persist, check the concitions and positions of the lock-out wires, and the mechanical adjustments on the coin mechanisms, before suspecting the electronics. If a coin mechanism rejects genuine coins, try to readjust it. If this is not successful, then replace it with a working mechanism.
C. FUSE REPLACEMENT Canyon Bomber contains seven fuses, five on the power supply assembly in the lower cabinet and two on the TV monitor assembly in the upper (TV) cabinet. All fuses are easily accessible through the rear access door. Replace fuses only with the same type of fuse as follows:
TEC TM-600/623 Monitors: 3AG 2-amp and 0.5-amp quick-blow, 250 volts Motorola M5000/M7000 Monitors: 3AG 0.8-amp quick-blow, 250 volts Power Supply: Fuses F1 and F2—3AG 3-amp slow-blow, 250 volts Fuses F3 and F4—3AG 2.5-amp slow-blow, 125 volts Fuse F5—3AG 8-amp quick-blow, 125 volts
D. LAMP KEPLACEMENT The game contains one fluorescent lamp located in the upper cabinet and one LED switch in each START button. Fluorescent Lamp Replacement Procedure (Refer to Figure 3-10) Remove three screws (button-head socket cap #10-32) at the top edge of the cabinet and remove the graphic panel retaining plate. Remove the two front graphics panels. Lamp is now accessible.
Fire Button Replacement Procedure (Refer to Figure 3-10) The fire button switches are accessible through the coin door. To change a fire button, unplug Molex connector, reach in through the coin door, and squeeze both sides of the switch and pull out.
E. TV MONITOR REMOVAL (Refer io Figure 3-10) Remove three screws (button-head socket cap #10-32) at the top edge of the cabinet and remove the graphic panel retaining plate. Remove the bezel and the two front graphics panels. At the rear of the cabinet, remove the TV monitor service panel which is secured by four screws. Remove the two bolts securing the monitor base to the cabinet. Disconnect the TV monitor harness and slide the monitor out through the front of the cabinet.
EF. TV MONITOR ADJUSTMENTS
The TV monitor should be adjusted only when the picture is distorted or ifthe contrast or brightness seem out of adjustment.
The monitor's adjustments function like those of a conventional, home television set, except that the volume adjustment has no effect. Instead, the game
Button-Head Screws
Graphics Panel Retainer Pilate
Fluorescent Lamp a
LED Switches
Plexiglas Shield
Carriage Bolts
Cardboard Bezel
Figure 3-10 Lamp and TV Monitor Removal
FUSE (5a en] FUSE (2A Quick-Blow) VOLTAGE SWITCH (always leave in right position) a a) ‘vert. \ VerT. HOLD HEIGHT contaasr| BRIGHT? HORIZ. HOLD. VOLTAGE SWITCH (always leave in Fight position) VERT. LIN.
MOTOROLA MODEL M5000/M7000 2 FUSES—REMOVE- ‘COVER TO REPLACE (both 0.88 Quick-Blow) ‘Contrast HORIZ. osc.: BRIGHTNESS Focus
MODEL TM-600/TM-623
Figure 3-11 Locations of Adjustments on TV Chassis produces its sound in circuits separate from the TV monitor. Figure 3-11 shows the location of the adjustments on both TV monitors used by Atari. Your game contains a TV monitor manufactured to Atari specifications by either Motorola or TEC. When making adjustments, follow these general guidelines: BRITE (Brightness)—Perform this adjustment before the contrast. Adjust so that the white lines covering the screen just barely disappear, when the brightness is turned up. CONT (Contrast)—Adjust so that the images are as bright as possible against the dark background without being biurred. HORIZ HOLD (Horizontal Hold) or HORIZ OSC (Horizontal! Oscillator)—Adjust if the picture is slightly off-center horizontally, if the images appear warped, or if the picture is broken up into a series of diagonal lines. Adjust for a stable, centered picture. VERT HOLD (Vertical Hold)—This needs adjustment only if the picture appears to be rolling up or down the screen. Adjust for a stable, centered picture.
G. LED START SWITCH REPLACEMENT Unlock and open the coin door. Disconnect the control panel cable connector and remove the four wing nuts (two bottom and two top) securing the control panel. Note that a ground wire is secured under one of the lower wing nuts. The LED switches are accessible when the panel has been removed. Remove wires from the suspected switch and turn the switch counterclockwise while holding the coneshaped nut on the outside of the game cabinet. Install a new switch using the reverse procedures. Reconnect the harness wires and when reinstalling the panel, be sure to secure the ground wire as before.
|. Unlock and open the Coin Door. Disconnect control panel cable connector; then remove two carriage bolts, Remove wires from suspected switch. Turn switch counterclockwise while holding cone-shaped nut on outside of game cabinet. Install new switch using reverse procedure.
- Reconnect harness wires.
Figure 3-12 LED Start Switch Replacement
A. GENERAL INFORMATION This chapter provides a technical description of the Canyon Bomber electronic circuitry. Electronically, the game consists of a power supply, a TV monitor, a game printed circuit board (PCB), and a speaker. Electrically, it consists of a control panel, a fluorescent light, and a coin door.
For easy reference the Canyon Bomber PCB is divided into 126 sections. These sections are identified by letters A through R (skipping letters G, 1, 0 and Q because they may be easily confused with numbers 6,1, and 0 respectively) for the short side of the PCB and numbers 1 through 9 for the long side of the PCB. For example, sheet 1 of Figure 4-8 illustrates an inverter £4 at the upper left-hand corner of the drawing. The component hardware of inverter £4 will be found at coordinates E and 4 on the PCB.
THEORY OF OPERATION
INTERLOCK SWITCH ac D POWER SOURCE TRANSFORMER
INTERLOCK SWITCH
BLACK PLAYER. STAI PUSHBI
LED
WHITE PLAYER START PUSHBUTTON _ Leo
WHITE FIRE BUTTON
COIN MECHANISM
BLACK FIRE BUTTON
SWITCH RT on HORIZONTAL DEFLECTIONS.
DEFLECTIONS
COMPOSITE VIDEO
PRINTED CIRCUIT WHITE PLAYER, AUDIO
BLACK PLAYER AUDIO
Figure 4-1
On the Canyon Bomber PCB schematic diagram (Figure 4-8) the symbol P appears at various inputs of the integrated circuits and indicates a connection to +5 VDC through one of the pull-up resistors R1, R2, R4, R26, R40, and R90.
The following circuitry discussion is separated into two sections—the microcomputer circuitry and game circuitry. Figure 4-2 is a block diagram of the entire Canyon Bomber PCB. Game Block Diagram
B. COMPONENTS OF THE MICROCOMPUTER SYSTEM (Refer to Figure 4-2) The microcomputer system carries out complex tasks of the game by performing a large number of simple tasks. Contrui of the system is the primary function of the microprocessing unit. The microprocessing unit causes the system to perform the desired operations by addressing the program memory for an
PROGRAM
SYNC. L L—<[ ADDRESS EAD} r
ADDRESS CONTROL
ADDRESS MEMORY
ROM MANUAL
ATTRACT
INTERFACE.
poo> PLAYFIELD | PLAYFIELD OUTPUT
GENERATOR
ee |
- [HORIZONTAL
IMOTION LOCATION
ENABLE
CAR VIDEO | OUTPUT I PICTURE I ROM i an i cs ee ee ee el MOTOR ]GENERATOR
AUDIO ‘AMPLIFIER [> TO SPEAKERS WHISTLE AND .BANG
TO Tv MONITOR jiagram Figure 4-2. Canyon Bomber PCB Block Di
instruction, reading that instruction, and then executing the simple task dictated by that instruction. Temporary storage of data necessary for the execution of future instructions, such as arithmetic operations, is stored in a read/write memory.
Program Memory (Bottom Half of Schematic Sheet 3) Program memory consists of read-only memories (ROMs), permanently programmed to execute the Canyon Bomber game. Program memory is either one ROMat D1, or 4 ROMs atH1, K1, N1, and R1. If the game is equipped for foreign languages, they will be stored in either one ROM at C1, or two ROMs at J1 and P1.
Since the data in the program memory is a permanent physical configuration of the ROM chips, the data is not lost when power is disconnected from the game or when the chip is removed from its socket. Since the program consists of read-only memory, the result of an address input can only be the “reading” of data stored in the manufacturing process. It is not possible to “write” in more data.
Read/Write Memory (Top Half of Schematic Sheet 3) Read/write memory consists of random-access memory (RAM), which actually contains eight random-access memories (2102-1s). Data may be stored in the RAM (called ‘writing’ the RAM), then later recailed (called “reading” the RAM). Memory size of the read/write memory is 1k x 8.
In order to read from the RAM, R/W (pins 3) input of all random-access memories must be a high logic level; to write into the RAM, R/W must be low.
As previously mentioned, data stored in the RAM is for the purpose of performing operations on data as instructed by the program memory. Since the RAM is atemporary storage area, removing power from the RAM chips will “erase’’ all stored data.
Microprocessing Unit As mentioned earlier, the controller of the microcomputer is the microprocessing unit (MPU). From the MPU, a sixteen-bit address bus addresses program memory, RAM, and an address decoder. An eight-bit bi-directional data bus serves as a path for transferring data from program memory, and for transferring data to and from the RAM and other interfacing devices. Tri-State Devices Tri-state devices, such as H3 of schematic sheet 3, are capable of having normal logic output of ones and zeros when disable (pin 1) is low. When disable is high, the output becomes a high impedance. In other words, when disable is high, it is equivalent to completely removing device H3 from the circuit. ROMs and RAMs are also tri-state devices. Each ROM or RAM must be enabled by a certain logic level at its chip-enable input before the device is capable of outputting or inputting data.
C. MICROCOMPUTER SYSTEM The primary function of the Canyon Bomber microcomputer is to instruct the game circuitry for the proper TV monitor display and audio outputs for corresponding manual inputs.
Program Memory Enable With initial power applied to the Canyon Bomber PCB, the MPU addresses program memory for an instruction by placing a 16-bit code at outputs ABO through AB15. The address decoder, consisting of decoders F6, E6 and addressable latch C7, receives the most significant bits of this address code as an instruction of which part of program memory to access. Outputs of one-of-ten decoder F6 enable only the individual ROMs of program memory required for the desired instruction.
RAM Enable Now, with the address decoder addressed to enable the desired program memory ROMs, and program memory addressed for a data insruction, the MPU receives an 8-bit data instruction from program memory on the data bus. If this data instruction includes the storage of information, the MPU addresses the RAM and writes the data into the memory RAMs. The procedure of writing into RAM is enabled by two signals; chip enable CE (pins 13) and RW (read/write, at pins 3) of the RAM must be low.
The address decoder F6 receives an address (A11 though A13) from the MPU. The result of these signals is a low DISPLAY signal at the input of multiplexer F2 for a low chip enable CE at pins 13 of the RAM. The MPU also causes the R/W input (pins 3) to the RAM to be pulsed, via the WRITE signal, When this input is pulled to low, MPU data on the data input to the RAM (pins 11) is stored into the RAM location determined by address inputs AO through A9.
Phase 1 and Phase 2 Phase 1 (1) and phase 2 (2) are outputs of the MPU and are formed by shaping the pulse of horizon-
tal synchronization pulse 4H by D-type flip-flop C6. The 4H input of C6 (pin 13) is fed twice through the flip-flop at a clock rate of 12.096 MHz. The output of the first flip-flop and the output of the second flipflop is fed through an OR gate to produce a phase 0
- signal, as illustrated in Figure 4-2. The MPU provides an output of ©2 that is exactly like 0, except with a slight delay, and an output 7 that is of an opposite phase of 2.
When ©1 is positive, the address and data lines of the MPU change and stabilize for the next output. When ®2 is positive, the MPU addresses memory on the address bus and inputs or outputs data on the data bus. In order to guarantee that the MPU data is written to external devices at the proper time, write enable (WRITE, C6 pin 15) is shaped by NAND gate B6 and D-type flip-flop C6 as ilustrated in Figure 4-3.
Phase 2 is also used to control the output of RAM address multiplexer D2, E2 and F2. The multiplexer acts.as a 12-pole double-throw switch, switched at a rate of 2. Again, as previously mentioned, the RAM is addressed by the MPU, and data is written into it when 2 is high. When 2 is low, the RAM is addressed by horizontal and vertical synchronization and data is read out of the RAM (see Figure 4-4). RAM Output The RAM has a second data output latch that places the RAM data at the output of D-type flip-flop K3 and )3 with the next rising edge of ®2 (clock input of K3 and J3).
D. MICROCOMPUTER WATCHDOG Watchdog is an external monitoring system that resets the program execution back to its initial instructions, if the program execution memory deviates from its intended sequence. This is accomplished by a watchdog statement (address code), incorporated in program memory, that results in a TIMER RESET pulse at the output of the address de~ coder. This reset pulse must occur before ring counter C4 reaches the count of five. Therefore if the program memory is functioning properly, a TIMER RESET pulse occurs within every five frames of video.
E. COMPONENTS OF CANYON BOMBER GAME CIRCUITRY The game ‘circuitry receives game instructions from the microcomputer and responds -with the proper video and audio outputs. Manual controls of the game circuitry provide control information as a data input to the microcomputer.
o — LT
ae
ee C6 pin 13
D6 Pin2
D6 Pint
C3 pin 37
C3 pin 39
C3 pin 3
Figure 4-3 Phase 1 and Phase 2 Signal Shaping
12 MHz
rs B6 pin 4
2 | B6 pin 5
| C6 pin 15
e-Nezo nsec" thee
Figure 4-4 RAM Write Enable Signal Shaping
System Clock and Sync Generator (Top of Schematic Sheet 1) The crystal-controlled clock generates a 12.096-MHz clock frequency that is used to produce all of the operating frequencies of the game. Note that the 9-bit binary counter (F4, D5, E5) counts from 128 to 512. This is accomplished by tying bit 128H (pin 5 of E5) toa pull-up resistor. Also note that the output of D-type flip-flop L6 is controlled by sync PROM J6é (programmable read-only memory programmed for the desired output).
The horizontal and vertical synchronization signals are used to produce a TV monitor raster made up of 262 horizontal lines at horizontal frequency of 15,750 Hz (256H). Synchronized with line 240 is a vertical blanking pulse that occurs for the duration of 22 more horizontal scans, resulting in the total number of 262 lines per frame.
Playfield Generator (Left Bottom of Schematic Sheet 1) The playfield generator generates both the playfield and all alphanumeric video for the TV monitor display. This is accomplished by the playfield ROM N8 and shift register N9.
The TV monitor display is made up of 32 horizontal by 30 vertical grid sections. For each grid section, there is a byte of data (one byte equals eight bits DO through D7) in the microcomputer RAM. During the ®2 cycle, the RAM is addressed by the MPU, at which time the desired byte of data is transferred from program memory to the data input of the RAM. Then, during the 1 cycle, the horizontal and vertical syn- OH 1H 2H 3H 4H 5H 6H 7H
Figure 4-5 Playfield Generator Character Trace for the Letter “C’”
chronization signals can access each of these bytes of data as that particular grid is to be displayed. The RAM then outputs six bits of data (DISPLAY 0 through DIS- PLAY 5) that address any of the 64 different alphanumerics and playfield characters stored in the playfield ROM.
The playfield ROM is programmed to provide four bits of data for each of 1024 addresses. The least significant addresses are from horizontal and vertical synchronization 4H, 1V, 2V, and 4V; the six most significant addresses are DISPLAY 0 through DISPLAY 5 from the microcomputer RAM. For each of the 1024 addresses, there is one of 64 grid pictures, each being eight scan lines high.
The top of Figure 4-5 jilustrates the letter C as it would be “traced” on the TV monitor display. The RAM would provide one six-bit address to the playfield ROM for the letter, while vertical synchronization 1V, 2V and 4V would complement the RAM address for each of the horizontal scan lines. The bottom of Figure 4-5 illustrates the output of shift register R3 for each horizontal scan.
Shift register N9 then loads the actual playfield or alphanumeric data from the playfield ROM and shifts it out in serial video (N9 pin 12).
Binary counter L7 latches data signal DISPLAY 7 from the microcomputer RAM. This results in the selection of white playfield video if DISPLAY 7 is high or black playfield video if DISPLAY 7 is low.
Binary counter L7 is also used to produce the COMP SYNC, COMP BLANK, and a 256H signal that are all delayed one character's width from their original timing. This delay is used to center the playfield on the monitor's horizontal scan,
Motion Generator The motion generator generates the video for the four moving objects of the Canyon Bomber game. The airplane picture ROM (consisting of ROMs MS Figure 4-6 TV Monitor Display
and N5 for a memory size of 1024 x 8) is programmed to provide 32 bits of data for each of the 16 lines of each of the four plane pictures of a car. The bombs are produced not from ROM, but from the setting of flip-flops R9
The microcomputer RAM provides data for displaying each plane or bomb picture. One byte determines the vertical location of the object, and another determines its horizontal location. Another byte determines the choice for the plane picture.
Vertical position data is received by vertical line comparator H5 and K5. Take for example, the data code for a plane to be displayed beginning on line 120. The RAM byte data code of 01111000 would be loaded into the comparator. When the vertical line comparator reaches the count of 01111000, and when 8H and 256H are all high, the conditions are met for a low logic level at the output of NAND gate K4 (pin 8). One ®2 clock pulse later, a low appears at the pin 5 output of latch J3 (clock input for J3 is located on schematic sheet 3). This initiates one of the eight vertical load pulses.
The RAM byte data code that controls plane selection is capable of addressing any of four different plane pictures. The two bits of data code necessary to do this (DISPLAY 3 and DISPLAY 4) are applied directly to the address input of the plane picture ROM NS5and M5. The least significant address lines applied to the plane picture ROM (inputs AO, A1, A2, and A3) determine which of the 16 lines of the plane is being described by the ROM data output, and which quarter of the plane will be displayed. Another signal, DISPLAY 7, reflects the picture horizontally. When 1H and 2H are both low, the video data output (VID 0 through VID 7) from the plane picture ROM is timed with load vertical pulse LDVTA.
Load vertical pulse LDV1A enables shift register R7 to load the video data from the plane picture ROM. This data is for the left quarter of the plane.
As 1H and 2H count up, the video data output (VID 0 through VID 7) from the airplane picture ROM sequentially loads the remaining shift registers P7, N7, and M7.
In review, the motion generator has received a RAM data code for where the plane is to be displayed vertically and a RAM data code for the proper picture of the plane. The final instruction needed is for the horizontal placement of the plane. The RAM byte that determines this is received by the plane horizontal location counter.
The object horizontal location counter P3 and N3 is loaded each horizontal line by a horizontal pulse LDHx. The counter is preset to a given count by the RAM data code (DISPLAY 0 through DISPLAY 7) during horizontal blanking. At the end of horizontal blanking 256H goes to high, and the counter is enabled to begin counting up ata clock rate of 6 MHz.
Video Output (Schematic Sheet 1) The video output circuit receives ail video signals and gates them together through summing resistors R41, R42, R43, and R44. SHIP 1, SHELL 1 and BLACK PLAYFIELD decrease the video voltage, making black. SHIP 2, SHELL2 and WHITE PLAYFIELD increase video voltage, making white.
Manual Control Interface (Left Side of Schematic Sheet 5) The main component of the manual control interface is multiplexer J8. This component acts as a one-pole 8-position switch, operated by address lines ADRO, ADR1, and ADR2 from the microcomputer MPU. Multiplexer J8 interfaces with two different sources of information—coin information and switch information. All information is received by the microcomputer MPU when the MPU addresses the address decoder for a low SWITCH signal that enables tri-state device H8 for a data output on the D7 data line.
Coin information is a matter of storing in the microcomputer RAM the number of times alow pulse appears on the data lines when the appropriate address input of multiplexer J8 is being addressed. The microcomputer MPU only “looks’’ for coin pulses during the attract mode. The fire buttons are connected to multiplexer K8.
Motor Generator (Top Right of Schematic Sheet 5) The key to the motor generator is the operation of transistor Q1 in conjunction with timer H9. Timer H9 operates as an oscillator with output frequency dependent upon the resistive charge path of capacitor C41.
Varying the collector-to-emitter resistive value of transistor Q1 varies the combined resistive charge path of capacitor C41 through transistor Q1 and resistors R48, R52, and R49. As the combined resistive value decreases, the output frequency of the timer increases. Variable resistor R52 makes it possible for the operator to adjust the frequency for a desirable motor idle sound.
The conductance of transistor Q1 is varied by grounding any combination of voltage-divider resistors R30, R31, R32, and R33. The combinations of these resistors are determined by data (from the microcomputer RAM) applied to the input of latch F8. Table 4-1 lists the approximate voltages at the base of
Table 4-1 Approximate Base Voltage of Transistor Q1 or Q2 for Given Address
Address
Base Voltage of Transistor Q1 or Q2 L AW1dS10.
5.00 VDC 4.25 VDC 4.08 VDC 3.95 VDC 3.77 VDC 3.65 VDC 3.52 VDC 3.42 VDC 3.22 VDC 3.13 VDC 3.03 VDC 2.95 VDC 2,84 VDC 2.77 VDC 2.69 VDC 2.62 VDC ONAUARWNAD Derrrerir@leiteririe-ice| oaAviudsia BITIrrr HK LrrTrrtrerere |ZaAvusia EZETEOEGIIere eee ee |eavusia Doerr rerrotrertirer
a 1s YORE
7 Motorola TV Monitor Schematic Figure 4.
WAVE FORM
(ose
Figure 4-7 TEC TV Monitor Schematic
transistor Q1 (or Q2) for the fifteen different address inputs. These addresses cause a latch condition of latch F8 only if alow MOTOR 1 signal enables latch F8.
To derive a realistic car motor sound, the output of timer H9 is divided into three separate frequencies by divider F9, then summed by resistors R53, R57, and R58. A divide-by-three signal at the QB (pin 11) output of F9is applied to summing resistor R58. Outputs QB and QD (pin 8) are also applied to Exclusive OR gate D8 to provide a divide-by-twelve signal at the QA (pin
- output of F9, which is applied to summing resistor R53.
Whistle Generator A555 (C9) is connected as an oscillator. The frequency is determined by the voltage on pin 5. When WHISTLE 1 goes high, C38 begins charging through R39 and CR3. This voltage is buffered and applied to pin 5 at C9. Therefore, as C38 charges, the oscillator frequency drops. The output is taken from the capacitor, buffered by Q5 and sent to the audio summing circuit. The frequency is adjustable with R59. When WHISTLE 1 goes low, the 555 (C9) is gated off through pin4, and C38is discharged through CR4 and the AND gate C8.
Audio Output The summed signals of the motor generators, and whistle and screech generator are applied to one leg of a 5k ohm potentiometer. Varying the wiper position of the potentiometer varies the signal of audio amplifier A11 or C11, and thus controls left and right speaker volume, respectively. The output of the audio amplifiers are connected to an eight-ohm speaker for each player.
HBLANE,
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction torbicden without the Specilic weitten permission of Atari. Inc.. Sunnyvale Calitornia, This drawing is only conditionally issued. and neither receipt nor possession thereat conters or transfers any night im. or license to use the subject matter of the Grawing or any design oF lechnical information shown thereon. nor any right 1o reproduce this crawing or any part thereo!. except for manufacture ay vendors of Atar Incor porated ang for manulacture under ihe corporation's wi {em license. no night to reproduce this crawing ts granted oF Ime subject matter thereo! unless by written agreement win oF written permission trom tne corporation. I: Je Ts |. 1s pioice|b | és ee ea bs ef es sya eT gig Te et Sse Te cm a had Seo ae or ye Ge a. oz as we
is
2383 gG43
veuanex
4 vBLANE | Taran + VBYNG
2238 2838
ese ed an 1pS02 an
wiguest wor ge Siée oo aB5,87 e70 &a ee Sie
[a] vireo oor E]vineo on
ie prpLay = ——"YJng, piseiaya ———Hlas NP piss s ———"nr DmPLAY & Vie oat prspus | 2s gt os 2 Dispur alaa § oe |!
| an | Alas 9 oi fit | cS |
| * | we 8 | Sp ware aerret |
aaers a ey eee
| a | aca | ‘> | sae |
| _ | onecava—Sfoo” | Sait | Eee |
| 25GK | flpy | cy |
o
| noene | la | — | ||
| crs | — | SYNE | Yasin 34 | Re |
| mm | VBumDK | Pe | oz}! | DMAP BLANER |
| 2, | e | re we | | Sista |
p ao
| rm | ota, | a |
an Ld
29 | oy 8), 24,24j40,90 (buccury EM wy gp -E]e 45
| ee | cee | 2a,2nea, | |
| ir | & | ie | Bie |
| te | 44-D]R | Ev | |
| Sys | 1 | bale] | 1 |
2]]= J
ay PEvAS ov i suns fal rRov (oe Res)
| We | wer | Too | ses, |
| T esver | ab | @ev |
| 3 ere iE | I | SYNE. VIDED OUT. PLAYELELD . BOWER |
= ese nem SIE eaves. rary ery
Sheet 1 of 5
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
a NOTICE TO ALL PEASONS RECEIVING THIS DRAWING CONFIDENTIAL Reproduction forbidden without the Specific wrillen permission of Alari. Inc... Sunnyvale California. This arawing is only conditionally issued. and ‘either receipt nor aossession thereo! confers or transters any right in. cr license to Use. the subject matter of the drawing or eny design or technical information shown thereon. norany nghi te repraduce this drawing or any part thereot. except for manutacture by vendors of Atar INCor porated and for manufacture under the corporation s wnt ten license. no right 1o reproduce this Gramngis granted or the subject matter thereo! uniess by written agreement vith or writen permission from the corporation,
Apane
Abas —
o
Apeto ae apes ——2)n0
wore KoTore EXeioee TIME RESET
PLAYER Wess TLel LAMP —_ 7 TR weistLe2 nod uo eh = 5 = i Yoo : BACT Re “
| a | “lis | fis} | - be — |
as} atrencrz 2
| Apes | a[te | ett | PLAYER = |
| ape? ——4}ar | gfe | tae |
avRe ——a
aoe -t aser Ase: 2 ases abea 2 anes 5] sore $ sper
MICROPROCESSOR
Figure 4-8 Canyon Bomber Schemat Sheet 2 of 5 Diagram
BISNALS & PIN NO, UWP FOR 80-7029 Tes B PLACES, EXCEPT WHERE SHOWN, > 2hhe 4
| wart | 2) ZA | + |
ps0 1 DRPTAY fei ¢ 28/7
| weev | aed | ‘a |
| a | co | veuse |
| Teen | 222 | prez ties |
| 5 | noes | ja |e |
a) wav ne Le pbus! peuse beuss
| talar 99-700 | Jus Is | recs | iu dis ls | |
| 19, | arin | he | sacag| M2 |g agcag] He | ge tie |
| Ts)iD* | 90-7020 | 30-7020 | s0-7020 |
anv
| is | AR? | = | 5 | : |
| yD | i | PP | ||
| 5 | is | AoRe |
esen ——" rap pel 28 van —
oan ApRa i
3eu peuse
| pore | nbs} | iu 48 |
us Pe ke ADR e ‘
| in | 90-7020 | 30-7020 [= |
| rae | eh | a |
ppusa -DBUS7
apaio.
DRS
ADee,
ADR7
ADR apes Apa ADR3 ADRE,
ADRt
RO zo —
3 NOTICE TO ALL PERSONS RECEIVING THIS DRAWING ADRIO she ee CONFIDENTIAL: Reproduction forbidden wathout the
| a | BRIS: | Specitic written permission of Alar. Inc. Sunnyval |
California This drawing 18 only conditionally issued. and neither receipt nor possession thereo! conters or transters am om Any night in-or heense fo use the subject matter of the atl Hg , Te[BS + coms drawing or any sign or fechaical information shown
| ‘Same | > | thereon. norany right to reproduce this drawing or any part |
| Fo | RIYA | ‘thereof. except for manufacture by vendors of Atari Incor- |
| 1°}90 | Roma, | poraled and for manufacture under the corparation $ writ- |
foniicensenorgntle reproduce tis drawings grad
{nin + unten permussion trom the corporation fos oe
| luo | 46] | DISPLAY 2. |
p> aa ovsetars
| Sao | 49i!° isPiaye | ro |
| | | the | e2 aseiave |
SEP aya tHE bisPeavs
| 20 | sal | oispeavd |
| TTT | | | + J |
i > LL 7 i
| + | Dy <a | pisPlays |
| 8 | DISPLAY 7 | CL |
“Ty 2 ae avn
| i | ol | x | ls |
| — | f | pause | |
| = | 2 | ut | DEUS |
a= a! KG ie ae pense
| jal | Ste | aus? |
_ Lt om
Tee Javea isjoe! Shes ‘
| a7 | I, | . | Perr | OS coerce Ba oc | i |
| jases elas | 9 | Sarg", | Seceny | bes | rr |
| ADRS alas | 8 | apa ait | gf | | | ADRE |
| poral | pssee 21, | aes | |||
| ose | alt | ne | : |
oe aye
| ae | roms 1° | pong | | |
‘ae _— MEMORY rine SIay gy aszelid, °',, [ut oause 027] 7). sorely, gf! eeu was ale. g
| sea) | 3], | & gale | pave |
| aasl | al, | 9 | |
| jasee| | 7]. | usd |
oa! ula, forall, eco Te
Figure 4-8 Canyon Bomber Schematic Diagram Sheet 3 of 5
bisPLay 7 ———¥ DISPLAY 6 ———SHar DISPLAYS, 4 BisPAYS fee
rev wav zy tev
DISPLAY 3 ‘gfe biseunv2 ——Sfar BSP Lay! Tae DISPLAYe e
av av zy Vv NOVICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL Reproduction forbidden without the specific written permussion of Atari Inc Sunnyvale Calforma This atawing is only condiionally issued. an neither recerp! nor posession thereof canters o lranslers any right i. oF icense to use, the subject matter of Ihe drawing oF any design oF technical inlormation shown thereon. nor any righ! to reproduce this drawing or any part thereot. except for manuilaclure by vendors of Aton INcor porated and for manulacture under the corporation swt fenlicense.noright 1oreproduce this drawing isaranted or the subject matier thereo! unless by watlen agreement vals oF Wwatten permission Iram the corporation
DigpLaye ———# S186 DISPLAY? a en ails
ss pisetaye = DIsPLays: DisPLaya, H DisPcAYS Tr piercaye id yea eth DisPLAY? ap \ UMPER:
cars [=> et, omnes de
2H
i ie we r etd. Tere
we ah
BS ws Je Ewe
io HERE Tan pe ce 5]52 p< SRE
wp
ving
vine
vide
vio™
aie pee Ta[ go) — ASE WN sss gees 5344, $543 Bee elz tee wea ald 2228 ooba'4 baba
sels lols AAAS {[ Pe bree Pree [pen fees Pe
| p | lees | oe | |
| ole, | PS | 1s | 3 |
| 2sex —> | ET eee TC | e | ref |
ewe —fp—Efar VEN? ee Be al 2 03 wa at ae ap we Tate ep eyejetcpe 9 sumeee 813] eee). ree | [53 win
| Boum | e | r | ay |
BsEe Waees 4448 354 5r 5558 beeg aaa aA eeu e re anon
Fi eee
| + | leer | He |
Ae er LS1e3 0 a1 @2 a Ge o1 a7 04 me
| i | jaqehenry™ | mejepeneyi 5 |
| F | sure | —2|53 4 — sar wine |
= S49! S538 ao 225 ly gee $55 5/8 Ban aly i _) Ly slo 2 La ls le Lo ae Ba BES Pe ° loce
| it | f | - | 4 | ||||
| vin? | ua | vio? | aa | + | re 2 | ther MO x | |
| Wee | Bes | ViDe- | ae oul? | t | es | ce Lelez | ae |
| Woe | val | viba | ae | a | ose az ae me) BO! | 2 | |
| Wide | aa | yee | Fiera | he fey | hate te 1 Yr | i | |
| vide: | IF | Vibe: | ie | _ | auBb | ||
| v1 | —2]e | Ver | ae | ag Ge | * | ||
| WiD0- | is, | vibe | : | ecu | 7 | yeon | |
| Tova, | be | UBVEA, | i | Eee | 252% | ||
| Bex | Ziee | 40840 | 3445 | ||||
| ia | Ih | gece | Rega | ||||
| cas | ole | Sov wD | Peas |
ab B ao bh AB f= + iF
| sle|s Jule | als [s lols | 2 | |||||||
| vio | n | \ | In | ||||||
| vio? | als | vee | vz] | j[Pe rs Fe Pe be | j[berire eee] | 882 —— 5 | |||
| wis | east | Vos | He | ant | Pace? | 5 | jeer | ase | ——= |
| ving | 4D 7 | Vibg | ge Pu | Wher PA ye FEI peer NG | bs | £ | |||
| vio! | Ae | le | een | aa | |||||
| vio | isles | Vide) | ale sie | fb 2p csios | eter LEGS | ||||
| vive | me | ve | se | It | 36 a1 G2 42 wR | 98 61 a? a3 wt | ||||
| wel, | a | you | zh, | Tare yey | fafa ety | ||||
| wis | f | Bay | |||||||
| 2 | Ba Be | . |
S) 9 a
wo7 vibe vibe viea vise Vine: vio Vib ie
MOTION
mM in
| vio? | : | yio7 | IK | |
| vibe | #7 | Jo | Woe | HtHals Me |
| Vins | e | > | vos | axl |
ra ig
| VIDS | P LsiesS | vide | > | ||
| ving | BS | | Vins tae sce] | |||
| wba | Fay | vibe | Fa | Bz | |
| vidi | An | vid | la. | w33e | sHiP2 |
| __vibo | ne | ving: | eH | ||
| ibys | Hse | coven. | ssh |
emne—tfehcx Gwe Pf aler i he
she wine — Figure 4-8 Canyon Bomber Schemati Sheet 4 of 5 ic Diagram
const
a)
| 1 | ea | ne |
1 er
ean _ vetank 2 peus7
2 e771) > |
| = | ol | 3 |
“Tepe Ree i Soft lE — peut STARTH NG — ad
| = | ~sv | 2 | 3 |
| . | i | x | pause |
cad | 1 Woe fia} La} | StAM
| Test
lox BPRS
Tete WA EER tA
TreUSt | noes THRUST 2,
Ape shee steke 2 s Fine Fieee
pause
beust
| 2 | Eee | is | NOTICE TO ALL PERSONS RECEIVING TH'S DRAWING |
| = | [oie ow | a | CONFIDENTIAL: Rearoduction forbidden without the |
SPTIONS Specific writien permssion of tar. inc... Sunnyvale California. This drawing it anly conditionally issued. and eit receipt nor possession tnerect confers ortrensiers fany right in oF license to use. the subject matter of the ‘raving of any design or technical information shown thereon. orany rightto reproduce hisdrawing orany part thereot except for manufacture by Vendors of Atari incor: porated and or manulactuve under the corporation sw Tenlicense.norightto reproduce this diawingis granted ef
| I | = | tne subject matter erect unless by writen ageasment | ||||
| - | —— | with'or writen petenssion fram the corperation, | ||||
| ay | L 4 | un | a | |||
| im | 12 | TSYBEN2 | ys | a | ||
| 2, | < | zl | oslt | |||
| be | wee | pes | —4f, | al | Lime PBF | oeion |
| ce | : | a | >Los | |||
| 5h" | oe | peuss—S}pe 7S aif | —_,_ | ad | rain 3 9x, | |
| ‘ | oe ® | evs | 7—E)p. 48 oso | 3 | a | |
| f | 1 | i | , | |||
| avt-Siee | are | DBUSe | we ale | Hi | a | |
| af? | . | 722K | ||||
| ale. | 5 | i) |
ExPLOBE — a gst avTRettt 2a 35 + avTeacte 120
2a BBO
Rae VAX AIS B33
220K
woToR 1
nat oak
peusa—}n peusi Sh, o,f? 228 vause—410s e6 asf 2 7 f 1s re Re pauss——Soy os 220%
woror &
45v
WHISTLE rl ese esok
WHISTLES 12 2 13 ATTRACT!
s Lh J. Ro Seg No
| 41, | 92 | fl |
2A @8.2¢ Ob ia fu To novoe. 1 SO 2a
Att
+3y sv
fe te s fe Sy 4 En he“ 2 09° [is wad, 72 re eaasacen| = ACTS |S py an Motor 2 SuD a4 TOK R7O Cae
YON ae
42ov Une
LOsi0N—W—9- é
| EXPLOSION | 3K | bli hehs > | $6? |
vou 158.uk
| ROE peo 652. | an | 2, | ty Fl avovo + |
| 13} reainca | [i | cS? |
se orf iat
| = | cot | FET? Fees | = |
= {f 201 Si somree, aupiot
| leone | cae | css | She | faily] 2 eve |
root awPuiReR tl
| i | Leopt 1 | L | = |
are | perms TeKe ot ; ISEE a. tov one expLosion AVY 4 ft fo ewes ar 9e, your 5 2Nseas Mae
| zee C8 | a | t | TH] VEL 2. |
pers cu SAA) tekinoe [a
+ cod ERED Jecwe
261 01 coe [ cet 59 Heat LS 220xt +1 v
INPUT. AUDIO
Figure 4-8 Canyon Bomber Schematic Diagram Sheet 5 of 5
UH POSITION EDGE CONNECTOR
Mov UNRES. MiBES _GeD BZAST
Vises, NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specitic written permission of Atari, Inc.. Sunnyvale, California. This drawing is only conditionally issued. and neither receipt nor possession thereat confers or transfers any right in, of license to use, the subject matter of the ‘drawing or ‘any design or technical information shown thereon nor any right i reproduce this drawing or any part thereof, except for manufacture by vendors ol Atar incor and for manufacture under the corparation’s writ. ‘no right to reproduce this drawingis granted oF t mailer thereof unless by written agisement with or written permission from the corporation
Re |
Heer No. FIRES NO.
StART ENG, Smet N oO | LOE fea Ii ie fn} [Oks |
Beene
ETN.
Test NS,
Higa SCORE OIA IESE
STAM NO.
Saree Sstaet ce | FSCO con COUNTER Lt ‘
' i SWITCHES LockouT! #2 CoML | SLAM i '
'
SIZIBIE}
Figure 4-9 Harness Schematic
ILLUSTRATED PARTS CATALOG
This parts catalog constitutes Chapter 5 of Canyon Bomber™ Operation, Maintenance and Service Manual. The purpose of this catalog is to provide you with the necessary information for ordering replacement parts for the Canyon Bomber game.
When ordering parts from your distributor, give the part number, part name, applicable page number of this catalog, and the serial number of your Canyon Bomber game (see inside front cover of this manual}. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.
lf there are any questions about this catalog, please contact our Customer Service Department. You may call them Monday through Friday from 7:30 a.m. to 4:00 p.m. Pacific Time at one of the following numbers:
from inside California, Alaska or Hawaii, call (408) 984-1900
from the remaining 47 states, call toll-free (800) 538-6892
er
a9 23.0 EA. eS
2, Be, |
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL Reproduction forbidden without the Specie watten permission of Atari. Inc. Sunnyvale California. This drawing 1s only conditionally issued. and neither eceipi nor possession inereo! conlers or transfers any aght in. oF license to use the subject matter of the Graming or any cesign oF technical information shown thereon -orany nightto feproduce this Grawing or any part thereat except for manulacture by vendors of Alan Incorporated ang lor manufacture under the corporation Swrittonlicense no nghttoreproduce this drawing isgranted or the subject matter thereo! uniess by writen agreement smith oe waten permission from the corporation DETAIL A pean |
Canyon Bomber Final Assembly A008911-01 D
Figure 5-1 Canyon Bomber Final Assembly A008911-01 D
- (0 Be.
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL. Reproduction forbidden without the specific written permission of Atari Inc. Sunnyvale California, This drawing ig only conditionally issued. and neither receipt nor possession thereof confers or teansfers any ight in. of license to Use, Ihe supject matter of the Grawing oF any design oF technical formation shown thereon, norany right to reproduce nis drawing or any part thereof, except for manufacture by vendors of AtarsIncor porated and for manulacture under the corporation s writ: fenlicense, no right reproduce this drawingis granted o¢ the subject matter thereo! unless by written agreement with oF written permission from the corporation.
Figure 5-1 Canyon Bomber Final Assembly Parts List
ATARI’
| Item | Part Number | Qty. | Description |
| 1 | A006871-04 | 1 | Cabinet Assembly W/Graphics |
| 2 | A007197-01 | 1 | Power Supply Assembly, Type B |
| 3 | A008913-01 | 1 | Control Panel Assembly |
| 4 | A006877-02 | 1 | Lower Rear Door Assembly W/Lock |
| 5 | A006917-07 | 1 | Fluorescent Light Assembly |
| 6 | A006885-01 | 1 | T.V. Shelf Assembly |
7 1
| 8 | A009002-XxX | 1 | Shipping Container Assembly |
| 9 | A009083-01 | 1 | Coin Door Assembly |
| 10 | A009262-03 | 1 | R.F. Shield Box Assembly |
| 1L | A007784-01 | 1 | Power Cord Assembly, Strain Relief |
| 12 | A009512-01 | 1 | R.F. Shield P.C.B. Assembly |
| 13 | A008314-02 | 1 | P.C.Bd. Assembly, Canyon Bomber |
| 14 | 006305-01 | 1 | Printed Poly Bag |
| 15 | 'TM-097 | 1 | Tech. Manual/ Illustrated Parts Catalog |
| 16 | 006873-01 | i | Retainer, Plexiglas |
| 17 | 008917-01 | 1 | Plexiglas Shield W/Graphics |
| 18 | 009010-02 | 1 | Bezel, Cardboard |
| 19 | 009011-01 | 1 | Speaker, Grill Cover |
| 20 | 005233-01 | 1 | Rear Door Seal |
| 21 | 006319-02 | 1 | Copyright Decal |
| 23 | A007902-01 | 1 | Cash Box Assembly |
| 24 | ST-097 | 1 | Self Test Chart |
| 25 | 006870-01 | 1 | Coin Box Bracket |
| 26 | 006852-01 | 1 | Upper Service Panel |
| 28 | 48-004 | 2 | Speakers, 5" |
| 29 | 73-77004 | 6 | Rivets, 3/16" O.D. x .68 Lg. (.250 x .500 Grip) |
| 30 | 46-201302 | 2 | Fuses, 3 AMP |
| 31 | 78-6601216 | 1 | Alum. Foil, 1" Wide x 5" Long |
| 32 | 78-6601216 | 1 | Alum. Foil, 1" Wide x 15" Lg. Approx |
| 33 | 82-8016 | 3 | Screws, Button Hd. Socket Cap #10-32 x 1.00 Lg. |
| 34 | 75-99090006 | 3 | Well Nuts, Blind Hole Fastener #10-32 |
| 36 | 75-5516B | Carriage Bolts, #% x 1.00 Lg (Black), | |
| 38 | 75-015S | Washers, Flat #5 | |
| 39 | 75-990505S | Hex Nuts, 4-20, Nylon Locking |
© 4 warner Communications Company
Figure 5-1 Canyon Bomber Final Assembly Parts List
[en part nusber {ory DESCRIPTION A006548-01 Test Switch Assembly 82-1824 Wood Screws, #8 x 1s Lg. Ft. Hd. Phil. 72-6610 Screw, Sm. Pan. Hd. Phil #6 x 5/8 Lg. 72-6608 Screws, Sm. Pan. Hd. Phil #6 x % Lg. 72-6808 Screw, Sm. Pan. Hd. Phil #8 x 4 Lg. 72-6812 Screw, Sm. Pan. Hd. Phil #8 x 3/4 Lg. 78-25001 Screw Down Tie Wraps 75-5120B Carriage Bolts, #10-24 x 1.25 Lg. 75-5132N Carriage Bolts, #10-24 x 2.00 Lg. 75-040 Washers, Split-Lock, #10 75-010S Washers, Flat #10 75-911S Hex Nuts, #10-24 75-9318 Wing Nuts, #10-24 A009511-01 Power Switches & Harness Assembly A009268-01 Main Harness Assembly HN BPE BRNADNNFORPARDOH
B 009024-01 Vacuum Formed Overlay with Graphics
4B
2 REQD ° O° O°
2)
| Fora
° ©
Figure 5-2 Power Supply Assembly A007197-01 D NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL, Reproduction forbidéen without the Specific written oermission of Atari. inc. Sunnyvale. California. This drawing is only conditionally issued. and neither receipt nor possession thereof conters or transters any right in. oF license to use. the subject matter of the drawing or any design or technical information shown {nereon. nor any right to reproduce this drawing or any part thereot. excep! for manulscture by vendors of Atari Incor porated and for manufacture under the corporation s writ Ten license, no right to reproduce this drawingis granted or the subject matter thereat uniess by written agreement ‘wth or written permission from the corporation
ATARI’ Figure 5-2 Power Supply Assembly Parts List
© 4 warmer Communications Company ‘Type B"
| Item | Part Number | Qty. | Description |
| 1 | A009266-01 | 1 | Power Supply Base Weldment Assemb]) |
| 2 | A006886-01 | 1 | Transformer Termination Assemb1 |
| 3 | 29-053 | 1 | Cap., Sprague Electrolytic 26,000uf @ 15V |
| 4 | 78-70501SC | 1 | Brkt., Cap. Mtg. Sprague #4586~-48 |
| 5 | A006555-01 | 1 | P.c. Board Rectifier |
| 7 | 79-4411004 | 5 | Fuse Holder, Panel Mounting |
| 8 | 41-2003 | 1 | Filter, Power Line, 5 AMP |
| 9 | A006958-01 | A/R | Voit Sel Block 95V |
| 10 | A006958-02 | " | Volt Sel Block 110V |
| 11 | A006958~-03 | or | Volt Sel Block 205V |
| 12 | A006958-04 | " | Volt Sel Block 220V |
| 13 | 78-2708 | 1 | Grommet ,Plastic |
| 14 | 72-1810S | 9 | Screw Pan Hd., #8-32 x 5/8"Lg. |
15.
| 16 | 75-048 | 9 | Washer, Split-Lock #8 |
| 17 | 75-918S | 9 | Nut Hex #8 |
| 18 | 75-0185 | 4 | Washer Flat #8 |
| 19 | A007192-01 | 1 | Power Switch Termination |
| 20 | A007444-01 | 1 | Power In Harness |
| 21 | 46-203801 | 1 | Fuse, 8 AMP, 125V, 3 AG Fast Acting |
| 22 | 46-201251 | 2 | Fuse, 24 AMP, 125V, Slow Acting |
(ow) 4a
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale. California, This d*awing is only conditionally issued. aad neither receipt nor possession thereof conters or transfers: any right in, 2° license to use. the subject matter of the ‘Srawing or any design or technical information shown thereon, norany right to reproduce thisdrawing or any part thereof, excest for manutacture by vendors of Alan Incorporated and for manufacture under the corporation's writ ten license. no right toreproduce this drawingis granted or the subject matter thereot uniess by written agreement with or written permission from the corporation. joa
WAT (Wouista 3595 WS HoH) uu
Figure 5-3 Control Panel Assembly em A008913-01 D
A. ATARI’ Figure 5-3 Control Panel Assembly Parts List
| Item | Part Number | Qty. | Description |
| 1 | 008915-01 | 1 | Control Panel W/Graphics |
| 2 | 001856-01 | 3 | Bushing, Alum |
| 3 | 62-002 | 2 | Led Switches, Lighted |
| 4 | A009338-01 | 2 | Fire Button Assembly See Figure 5-4 |
| 5 | A009269-01 | 1 | Control Harness Assembly, Canyon Bomber |
| 6 | 62-009 | 1 | Switch, Licon (Blk. Cap) |
| 7 | 75-5120BX | 2 | Carriage Bolts, #10-24 x 1.25 Black |
| 8 | 75-040 | 2 | Lock Washer, #% Split |
| i) | 75-9118 | 2 | Hex Nuts, #10-24 |
© 4 warmer Communications Company
CONTROL PANEL (REF)
(SYS) GEA. REDD)
(EA. REA'D)
NOTICE TO ALL PERSONS RECEIVING TalS DRAWING CONFIDENTIAL: Reproduction fordidcien without the specitic written permission of Atari. Inc., Sunnyvale, California, This drawing is only conditionally ‘either receipt nor possession inereo! confers or transfers: any right in. oF license to use. the subject matter af the ‘drawing oF any design or technical iatormation shown thereon. 0r any right to reproduce this drawing or any pa thereof. except for manufacture by vendors of Atari porated and or manufacture under the corporation's writ- {en license. norightto reproduce this crawingis granted or the subject maver thereof uniess by writlen agreement with or written permission from the Corporation.
Figure 5-4 Fire Button Assembly A009338-01 C
Figure 5-4 Fire Button Assembly Parts List
ATARI"
| Item | Part Number | Qty. | Description | | |
| 1 | 006530-01 | 1 | BEZEL | |
| 2 | 006535-01 | 1 | BUTTON | |
| 3 | 006532-01 | 1 | CHASSIS | |
| 4 | 006533-02 | 1 | SWITCH, MOUNTING PLATE | |
| 5 | 62-020 | 1 | SWITCH, CHERRY E68-50A | |
| 6 | 72-1603 | 4 | MACH., SCREW #6-32 x 3/16 LG PAN HD PHIL | |
| 7 | 82-8808B | 4 | MACH., SCREW #8-32 x 1/2 L& ALLEN SOCKET HEAD | |
| 8 | 75-918s | 4 | NUT, 8-32 | |
| 9 | 75-048 | 4 | WASHER, #8 SPLIT LOCK | |
| 10 | 75-046 | 4 | WASHER, #6 SPLIT LOCK |
© 4 warner Communications Company
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Figure 5-5 Fluorescent Light Assembly Parts List
ATARI
Part Number Description
| 1 | 93-102 | 1 | Gibson Fluorescent Fixture 24 Inch |
| 2 | 70-301 | 1 | Fluorescent Tube 24 Inch |
| 3 | A006916-05 | i | Fluorescent Light Harness, 18" |
| 4 | 78-2652 | 1 | Grommet, Rubber |
| 5 | 78-24001 | B/R | Tie Wrap |
| 6 | 79-561816 | 2 | Wire Nut, Ideal 71-B |
© 4 warner Communications Company
BEA.REQ'D. NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL, Reproduction ferbidden witnout ine Specitic written permission of Alari, Inc,. Sunnyvale California. This drawing is only conditionally issued. ana either receipt nar possession theraaf conters or transters any Fightin, oF license to use, the subjeet matter of the ‘acawing oF any design er technical infarmation shown thereon. nor any right to reproduce this drawing orany part thereo! except for manutacture by vendors of Kari Incorporated and or manutacture under the corporalicn's writ-
- tenlicense, norghtto reproducethis drawingis granted ot the subject maitor thereot uniess ay written agreement with oF written permission from the corporation.
APPLY ITEM 8 OUER SOLES 'N TUL SHELF, AS SHOWN, ON ONE SIDE.
ZX APPLY RLU. SILI@NE: RUBBER (GE IDB OR EQUIV.) WRERE SROWN.
Figure 5-6 TV Shelf Assembly A006885-01 C
ATART Figure 5-6 TV Shelf Assembly Parts List
© ‘Warner Communications Company (Approx. )
| Item | Part Number | Qty. | Description |
| 1 | 006857-01 | 1 | T.V. Mounting Board |
| 2 | 92-032 | 1 | T.V. Monitor, 23" |
| 3 | 006874-01 | a | Plexiglas Retainer |
| 4 | 75-5120B | 5 | Carriage Bolts, #10-24 x ls Lg. |
| 5 | 75-040 | 5 | Washers, Split-Lock #10 |
| 6 | 75-0108 | 5 | Washers, Flat, #10 |
| 7 | 75-911S | 5: | Hex Nuts, #10-24 |
| 8 | 78-6601216 | 1 | Alum. Foil, 1" Wide xlo" Lg. |
| 9 | 75-0158 | 2 | Flat Washer, #% |
- 2 PLoS,
- tees at) 2 pLes
- eves
Gojerics (a, 4 recs
Biz res
wus “ q
On/aiK,
remo)
Figure 5-7 Coin Door Assembly NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Aeprocuction forbidden wilhout the spocilic written pormission of Alani. Inc. Sunayvate California, This drawing is only conditionally issued. ana nether receipt nor possession theraot confers or transfers ‘any right in. oF license ‘o use, the subject matter of tne tawing oF any design ot technical information shown tereon. gran} right to reproduce this drawing or any part thereat. except for maa uiacture by vendors of Atari Ineo” porated and for manutacture under tne corporation s weten icense. no rignttoreproduceths drawing granted or the subject matter thereo! unless by written agreement ‘wll or written permission fram the corporatien.
A006794-01 through -07. C
Figure 5-7 Coin Door Assembly Parts List
(D * Warner Communications Company Door Door Door Door Door Door Assy. Assy. Assy. Assy. Assy. Assy. Part Number Qty. Description
| A007637-01 | 1 | Pront Bezel Assy. - Used oly |
A007637-02 Ref.| Front Bezel Assy. - Used only on -02 Coin A007637-03 Ref.| Front Bezel Assy. - Used only om -03 Coin A007637-04 Ref£.] Front Bezel Assy. - Used only on -04 Coin A007637-05 Ref.| Pront Bezel Assy. - Used only on -05 Coin A007637-06 Ref.] Front Pezel Assy. ~ Used only on -06 Coin A007637-07 Ref.) Pront Bezel Assy. - Used only on -07 Coin
| 75-9165 | 4 | Nut 6-32 |
| 007639-01 | 1 | Coin Lock-Out Assembly |
| 007640-01 | 2 | Coin Switch Assembly |
| 4002465-01 | 1 | Coin Counter Assembly |
| 004320-01 | 1l | Coin Door Weldment |
| 004341-01 | 2 | Secondary Coin Chute |
| 004344-01 | 1 | Key Loop |
| 004340-01 | 2 | Spring-Return |
| 004337-01 | 2 | Bracket, Wire Form |
| 004338-01 | 1 | LockyOut, Wire Form, R.H. |
| 004336-01 | 1 | Lock-Out, Wire Form, L.H. |
| 004326-01 | 2 | Button, Scavenger |
| 75-046 | 4 | Lock Washer, #6 |
| 006904-01 | 2 | Spacer |
| 007359-01 | 1 | Lamp Socket |
| 70-11-47 | 1 | Lamp |
| 73-3008 | 2 | Retaining "C" Ring, Truarc #5103-25 |
| 75-9914001 | 6 | Sel£-Threading Nut, Tinnerman #SR188006 |
| 75-026S | 4 | Washer #6 |
| 75-00516 | 13 | Kepnut, Style 842, Stl., 6-32 |
| 008629-01 | 2 | Spring |
| 71-2118 | i | Lock Assembly, Hudson Lock |
| 71-1225CU | 2 | Coin Mechanism for American Quarter only |
T1-125FB Ref.} Coin Mechanism for Belgian 5 Francs Only 71-121MG Ref.| Coin Mechanism for German Mark only 71-121KS Ref.] Coin Mechanism for Swedish Krona Only 71-12100Y Ref.| Coin Mechanism for Japanese 100 Yen Only 71-1210PE Ref.] Coin Mechanism for English 10 Pence Only 71-1220CA Ref.! Coin Mechanism for Australian 20-Cent Piece only
| 007753-01 | L | Plate, Anti~Probe |
A007638-01 Switch Assembly - Slam 4006921-01 Harness Assembly
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc.. Suncyvale California, This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in. or license to use. the subject matter of the rawing oF any design or technical information shown thereon, norany right to reproduce this drawing or any part thereot. except for manulacture by vendors of Atar incor orated and for manutacture under the corporation # writtenlicense. no rightio reproduce this drawing is granted or the subject matter thereat unless by writen agreement with oF written permission trom the corporation.
da 6s a wall
Ades b Wall v y
| wo | oO | oo | oon |
| > | oO | foe} | oo |
e is} os—
| » | 1 | cos] | on |
| N | | | ae} | or |
® joe +
| . | lo | oO % | ||
| S | |O | co | oor | |
| = | Oo | 20 | oF | fe) |
| cS | 9 | co | Of | |
| a | a | oO | ov | |
| x | lo | co | of | |
| a | lo. | co | ow | |
| € | jo | co | o4 | |
| a | ° | oo | Of | |
| > | o—w | O¢ |
Saree x oO a N
ie} QO
Figure 5-8 RF Shield PCB Assembly A009512-01 D
Figure 5-8 RF Shield PCB Assembly Parts List ATARI’
| Item | | Part Number | Qty. | ‘Description |
| } | 006549-01 | \ | P.C. Board |
| 2 | 79=517222 | 1 | Connector, 44 Pin P.C. Mount |
| 3 | 27-250104 | 7 | Cap, Cer Disc Q.1pf 25V (Large) |
| 4 | 27-A250104 | 9 | Cap, Cer Disc O.lpf 25V (Small, Bottom Row) |
| 5 | 41-3003 | 2 | Inductor, 100uh (Large) |
| 6 | 41-3004 | 9 | Inductor, 100uh (Small, Bottom Row) |
| 7 | 52-003 | 1 | Jumper, -60 Centers |
| 8 | 52-004 | 4 | Jumper, «30 Centers |
NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction forbidden without the written. permission of Atari. Inc. Sunnyvale, a This drawing Is only conditionally issued. receipt nor possession thereof conters or tanslers {any night in-or license to use. the subject matter of the drawing thereon. nar eny right to reproduce this drawing or any part thereot. except tar manutacture by vendors of Atar\Incorporated and for manutacture under the corporation's writ tenlicense.no right to reproduce this drawingis granted or the subject matter tnereot uniess by wntten agreement vwith'oF written permission ‘rom the corporation SNOIS2t9A 1o-
antereneay igi
28) +7 Sinn — Figure 5-9 Canyon Bomber PCB Assembly A008313-01 D
Figure 5-9 Canyon Bomber PCB Assembly Parts List \ PROM Version ATARI
Item Part Number Qty. Description 1 008313-01 1 P.C. BOARD |
2 10-5101 2 RES. CARBON, 5%, kW, 100 OHM R16,17
3 10-5102 13 7 " " “ 1K 7 R1,2,4,7,26 40 ,61,63,67 68,80,90 , 91
4 10-5103 35 " " " " 10K " R8-15,18-25 27,28,45-48 50,51,53,54 57,58, 70-72, 84,86 ,75 78
5 10-5104 z " " " " 100K" R74,77
6 10-5105 2 " " " " iM " R30, 37
7 10-5182 3 " " " " 1.8K " R41,43,44
9 10-5222 1 " " " 7 2.2K " R79
10 10-5224 2 " " " " 220K ia R33,36
11 10-5225 2 7 " " : 2.2M ” R31,38
12 10-5331 3 " " " " 330 " R3,6,42
13 10-5392 1 " : " “ 3.9K" R81
14 10-5335 2 " " " " 3.3M s+" R49,55
15 10-5471 1 " " " m 470 . RS
16 10-5474 2 " " " " 470K 7 R32,35
17 10-5562 2 " " " " 5.6K” R62,64
18 10-5683 4 " " " " 68K ™ R29,34,39,65
19 1LO- £822 1 ™ " " ” 8.2K " R82
20 19-315502 2 FRIMPOT, 5K OHM R83,88
21 19=315254 2 TRIMPOT, 250K OHM R52,56 22 19-sD9W2PO 1 RES, WIREWOUND 20W, > OHM R89
© 4 Warner Communications Company
PROM Version Figure 5-9 Canyon Bomber PCB Assembly Parts List
—_—_—_—$ $$$ ——————— item | Pan Number | Qty Description Tem | Part Number [@t~ Description
56 | 37-7408 2. || nmeorateperecure aos ce,a9 4 || mes, CARBON, WH, 58 39K OH —-R73,76,60,66 St | areata * : ‘ To 4 2 || remot aoox om 259,69 58 x maa 1 || capyetacrmonvere Sut 25 C51 58 4 7020 2 ||. " ont (ean ae 60 a 7430 1 22008 35. ot 5 7432 2 o00u# ces.€7 a * a Tout cos. 8 “ 4,078 | Ba 2 aut 36,37 «4 1 TALSOO BS
6 2 74835 x5 so} 27-250102 2 || ene, comnmte orse ce4.69 a 3 TaBE gerES OG 33 | 27-250203 elf . F142, 44,45, id 2 ast oA
52,62 6 2 7492 09,F9 a4 | 27-250108 45 ale ey a waist
ro | 37-7a153 2 ass 35 | 27250224 Fy azut m | 37-7ars163 8 yarsi63 e n 2 raiea
pb 8 7aK65 1 || cap bree mica, to0p¢ 1000 2g 2 || cap puree mica, 2z0p¢ oov c5a,60 1” 3 a7 33,K3,c6 2 || capmmar, oluf,1000 49,50 6 4 74175 16,A8,£8,F8
6 1 7a195 Ko 7 2 9301 F6,m8 43 | si-aar 2 || prone sae cr7.8 % 5 9316 05,85, 16,K6,27 4a | sansa 6 || rome, wos cnl-6 cy 2 9321 B5,ee 45 80 5 9322 p2,82,F2,"5,R5 48 a 2 93347 ° a 2 eres ra,04 as | s3-2msca0 2 || ananstszor, 2ua644 ae 93 6 997 A2,52,C2,P3,49 49 | 24-2n3643 a || meansrstos, ansea3 93-6 Be 0 84 4 555 59,C9,20,49 51 s 2 || aupro awe roalood a/BiL C11 52 % a |} seouratoe 323 53 2. || twracraren crrcurt 7400 A619 a7 sa 1 . : 402 x7 = 55 2 7408 Fa, BT ea Ce
Figure 5-9 Canyon Bomber PCB Assembly Parts List PROM Version
A ATARI’ Tem [Part Number | Qty.
Description
———$—<$—$— Sm c“r ‘Part Number
Description 30 | 52-004 6 sa | 2003 cy 96 | 62-0 a 95 | e6-n1arr7 1 os 99 | 77-1608 2 75-016 2 75-056 2 75-9160 2 os aos} 79-0600 2 107 | 909470-01 2 108 | 72-23016 aR 19 | 72-2605, a ue un a2 113 | 79-42040 1 as us ur | 90-202 1 ne us aa | 90-010 1 az2 | 90-7012 2 123 | 90-7020 .
SUNPER .30 CENTERS JUMPER «60 CENTEI SWITCH, SPS, woMEWTARY wa SWITCH, SpST xB, DIP om, SCREWS, PAN HD PHIL, #6-32 x 4 1g, eres wexrsrex (24323) HRARSENK (TDA1004) CEMENT (7DAL004 HEATSENK) STLPAD (1323) SOCKET, 40 PIN, MSD INSERTION ©3 CRYSIAL, 22.096 Miz cy ROEORATED CTRCUIT 3 aM, 2001, aM, 212028,
09491 oos4s2 09505 03506 009457 09498 009499 209500 009501 009502 009503 ons04
(CANYON BOMBER SYNC PROM CANYON BOMBER GRAPHICS PROM CANYON BOMBER PICTURE PROM 15 CanYON BOMBER PICTURE PROM MSB [CANYON BOMBER PROGRAM PROM
oa eu dune ns ws M5 u a m a m PL RL
Figure 5-9 Canyon Bomber PCB Assembly Parts List ROM Version
ATARI
Item Part Number Qty. Description
1 008313-01 1 P.C. BOARD
2 10-5101 2 RES. CARBON, 53, 4W, 100 OHM R16,17
| 3 10-5102 13 " " " " 1K “ R1,2,4,7,26 | 40,61,63,67 68,80,90, 91
4 10-5103 35 " " " " 10K " R8-15,18-25 | 27,28,45-48 1 50,51,53,54 57,58,70-72 84 ,86,75,78 5 10-5104 2 " " 7 4 100K" R74,77
6 10-5105 2 " " " : im 7 R30, 37
7 10-5182 3 " " " " 1.8K" R41,43,44
9 10-5222 1 " " " i 2.2K" R79
10 10-5224 2 : " ” m 220K CO” R33,36 far 10-5225 2 7 " s 2.2m " R31,38
j 12 10-5331 3 " a " " 330 B R3,6,42
13 10-5392 1 " " iW : 3.9K" R81 14 10-5335 2 " " " . 3.3M—=«" R49,55
1s 10-5471 1 " # " " 470 . R5
| 16 10-5474 2 : a " " 470K" R32,35
17 10-5562 2 2 " " " 5.6K" R62,64
18 10-5683 4 7 " " " 68K a R29,34,39,65
19 10-5822 1 " " " " 8.2K" R82
20 19-315502 2 =RIMPOT, 5K OHM R83,88 21 19-315254 2 | TRIMPOT, 250K OHM R52,56 22 19-8D9W2PO0 1 RES, WIREWOUND 20W, 2 OHM R89
ee © » v2rr2r communications Company
Figure 5-9 Canyon Bomber PCB Assembly Parts List ROM Version
pu ny Tem | Par Nomber [90 Deseripion Tom | Par Number Descntion
36 | s7-7000 ‘wrbonateDonncuz® Tae 68.09 a |) es. enanow, sx, 24 32K om #5476 , 60,66 s | a-ra0 ne rao 38 2 || samen, roox om 19,65 se | ara yas 33 ‘ (CAP, ELECTROLYTIC — Suf 25v 0 CSL. a 13,14 ,56,K9 Ps | cn ca8.39 6 rao 1 2aout os a 506,388.89 a sovout css.67 e 1 4700u8 ces 33 HA,IT-RS | Pe a we exe. oa j
“5 2 2 || cx, emmame sxse 6 3 5.08 | ” t 4
6 2 v.89 ae | ar-asoioe 6 6 1 x0
1 2 F as] sv-asoaza 1 vate na a vom pe = n 2 A138 2 | asanion 1 |] ca oxpesn mica, 2000 100v C24 ” i ween. 26 Ro as | aeiorzas exe orpreD with, 22096 300 C34,60 Py 3 vee ao | 22-1103 2 |] cre, omar, .oluf, 100v 49,50 6 J« Le,A8 28,78 a 16 1 x9 “a 7 2 F6.m9 a | ema > || oxooe mer cn. 7 : soca ne ne,e7 a | nmr © |) orooe, wore ens is ; ae ° 80 5 22 82-72 75,25
- a 2 7
e 2 oe 2 || rmaaszston, axasca oa - ‘ mara a || snaserston, anaes ons =
se ‘ 558 u0,c9,0.89 os | oaioos va1n.c1, 6 1 |] secoaron oa 2 |jssmeceanen concur 1400.9 7 1 ss nor 7 26 2 so aca 28,07 °
-9 Canyon Bomber PCB Assembly Figure 5: Parts List ROM Version
Description SUNPER -30 CENTERS JUNPEA «60 CENTER SWITCH, SPST, NOMENTARE SwrTcH, sper xe, DIP
wa sn. SCREWS, PAN MD PUTL,#6-32 xb Ig, Cres
stares SILPAD (1M323),
SOCKET, 40 PIN, MED INSERTION
CRESTAL, 12.996 itz a
a
CANYON BOMBER SNC FROM ‘CANYON BOMBER GRAPHICS PROM Ne CCAWox SOMBER DICTURE PROM ISB NS CChWYOR BOMBER PICTURE PROM MSB MS CANON BORER. PROGRAM ROM 3 a " . m4 bp
TM-097 2nd PRINTING
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A. If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name Firm C] Distributor Operator Address U1 Other
City State Zip
First Fold
First Class Permit #1004 Sunnyvale, CA eee eee i hk er is a ee
g
= Atari, Inc. g P.O. Box 9027 3 Sunnyvale, California 94086 &
Attn.: Publications Group, Coin-Op Engineering
TTT TT Becond Fo CSCiC“~s~—~s‘“=s“<“< CO
980%6 VO ‘ajeakuung 4206 XO ‘O'd “our ‘yeyy
a6pz siy, ede,
WARRANTY
Seller warrants that its printed circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its television monitors (in games supplied with monitors) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
If the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such produets are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits, loss of use, incidental or consequential damages.
EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BE- TWEEN SELLER AND BUYER WHIGH GONTRACT SUPERSEDES THE TERMS OF THIS ORDER, THIS WARRANTY IS EXPRESSED IN LIEU OF ALL OTHER WARRANTIES EX- PRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES GF MERCHANTA- BILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND OF ALL OTHER OBLIGA- TIONS OR LIABILITIES ON-THE SELLER'S PART, AND IT NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR THE SELLER ANY OTHER LIABILITIES IN CONNECTION WITH THE SALE OF PRODUCTS UNDER THIS OR- DER,
This document is and contains confidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Ine.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc.
ATARI INC # 1265 BORREGAS AVENUE SUNNYVALE, CALIFORNIA 94086, 4087: 1000 * TELEX 35-7488