CATHODE RAY TOMES

Space Dungeon Manual (72-00014-001)

Space Dungeon (Taito America Corporation, 1981) · Manual · 64 pages · 17 sections · original scan

Page 1

aire. J ©1982 Trade Marks of Taito America Corporation 72-00014-001

Page 2

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 3
Scan of page 3

This page is a drawing, shown as the original scan.

Page 4

Reproduction of this publication is forbidden without the written permission of TAITO

AMERICA CORPORATION, Elk Grove Village, Illinois. This manual is only conditionally

issued, and neither receipt nor possession thereof confers or transfers any right in, or

license to use, the subject matter of the manual or any technical information contained

thereof.

For permission requests, write: TAITO AMERICA CORPORATION 1256 Estes Avenue Elk Grove Village, Illinois 60007 Telephone (312) 981-1000 Telex 25-3290

Page 5

1.

2.

3. “SPACE DUNGEON” UPRIGHT

TABLE OF CONTENTS

“SPACE DUNGEON’’™ GAME SET-UP ........... Page 5 4, ILLUSTRATION & PART LISTS..................... 25

1.4 Game Features ..... 2.0.00 cc cece cece ee 6 Figure 1 {ncandescent Panel ...........-..2..4 26

1.2 Introduction .......... 26... 60 ceee eee e eee 6 Figure 2 8-Way Joystick ...... 00.0.0. cece eee 27 1.3 Game Inspection .........- 00. .0.ee eee eee ee 6 Figure 3 Control Panel ...............0.00005 28 1.4 Pre-Game Installation ...................2.004 6 Figure 4 Door AsseMbY ........ ov cseeeeceee 30 1.5 Power On/Off Switch, Interlock Switch, . Memory Protect Switch, Self Test Switch, Figure 5 Coin Door ........ 22. .ee eee ee eee 32 Volume Control, and Service Outiet............. 7 , Figure 6 Coin Door ........... 00. eee eee 34 1.6 Electronic Acceptors ............0.... cece eee 7 Figure 7 Cabinet Assembly Front View .......... 36 1.7 Game Installation.......... 00.0... .0eeeee eee 7 Figure 8 binet Assembly Rear View .......... 1.8 Self Test Procedure ...........seeeceeeeeeeee 8 a Cabinet Assembly Rear View 38

Figure 9 Regulator P.C.B Component Layout ... .40 MAINTENANCE ................00 060... ce eee eee 15 Figure 10 Video Processor Component Layout ....43 . WIS noes ese ee bie eee eile yh age ed ta 16 . 21 Weaning Figure 11 Data/Sound Processor 2.2 Coin Door 0... ..00. cece eee cece eee eee 16 Component Layout ................ 48

2.3 Fuse Replacement ...............-0200002008 16 Figure 12 ROM/I/0 P.C. Assembly Component Layout ................ 52 2.4 Monitor Removal.................--..000 eee 16 Figure 13 Coin Processor Board Layout .........' 56 2.5 Cover Glass Removal ......--..... 000s eee ees 7 2.6 Printed Circuit Board Replacement ............. 7 Figure;14 Goin, Processor. Board Senematic: «<1 7

2.7 Power Supply .....-cecececceveeeeeseeeeese 7 Figure 15 Wiring Diagram

2.8 CMOS RAM............cccccceceeeeeeeeeee 19 Figure 16 Regulator P.C.B. Schematic (Fold Out)

2.9 Test Points..........-. 6... c eee eee neces 19 Figure 17 Video Processor Board Schematic 1 of 2 (Fold Out) fee see 9 ois wre ee 1 THEDRY OF DFERATIONS 2 Figure 18 Video Processor Board Schematic 2 of 2 (Fold Out) 3.1 General... 0... eect eee eee 22 , Figure 19 Data/Sound Processor Board Schematic 3.2 Video Board ........ 00. eee cece eee ee 22 (Fold Out) new Oe Ped 8G a chee eee OF a ome A 23 5.3. Data Sound Board Figure 20 ROM/I/O Board Schematic (Fold Out)

3.4 ROMA/O Board ......... 0... cee eee eee eee 24

Page 6

LIST OF ILLUSTRATIONS

Figure 1-1 Programming Plug.................04 6

Figure 1-2 Power ON/OFF Switch ................ 7

Figure 1-3 Interlock Switch & Memory Protect Switch7

Figure 1-4 Self Test Switches .............-.0005 7

Figure 1-5 Volume Controi Setting ............... 7

Figure 1-6 Self Test Button ..........0.000.0000. 8

Figure 1-7 Video Board (On Service Door) ......... 9

Figure 1-8 = Flow Chart ................0000.000. 10 Figure 1-9 Color Bar «oo... eee eee eee 10 Figure 1-10 Color Bar ...............0.ee ee 10 Figure 1-11 Color Bar .. 2.2... eee eee an

Figure 2-1 Goin Mechanism.................0005 16

Figure 2-2 Fuse Replacement .................. 16

Figure 2-3 Monitor Removal ................00. 16

Figure 2-4 Cover Glass Removal ................ 17

Figure 2-5 Printed Circuit Boards ............... 17

Figure 2-6 Power Supply ..................0008 7

Figure 2-7 Current Limit Adjustment ............. 18

Figure 3-1 Clock Timing................0 02.08 22

Figure 3-2 Dual Port RAM Timing ............... 23 LIST OF TABLES

Table 1-1

Table 1-2

Table 1-3

Table 1-4

Table 1-5

Table 1-6

Table 1-7

Table 1-8

Table 1-9

Table 1-10

Table 2-1

Table 2-2

Table 2-3

Table 2-4

Table 3-1

Table 3-2

Table 3-3 Self Test Switches .................... 7

Hardware Tests ................000005 8

Video Board ROM Checksum ........... 8

Decoding Jumper Location ............. 8

Video Board RAM Checksum ........... 9

Data/Sound Board ROM Checksum....... 9

Screen RAM Content ................. 1

Audit Totals ........ 0.6... cece eee 12

Standard Coin Setting ................ 13

Custom Coin Setting ................ 13

Line Voltage ................0..00008 7

Secondary Fuses ................0004 18

Data/Sound Board Test Points ......... 19

Video Board Test Points .............. 19

Video Board Memory Map........-.... 22

Register Initialization ................. 23

Data/Sound Memory Map ............. 24

Page 7

Game Set-Up

Page 8

“SPACE DUNGEON’™ UPRIGHT

  • GAME SET-UP

1.1 GAME FEATURES TAITO AMERICA CORPORATION'S “SPACE DUNGEONS’ upright game is housed in a compact and highly serviceable cabinet with many added features. A larger security designed cash box has been incorporated into the design of this cabinet. By putting wheels on the cabinet, moving the game from one location to another is made much easier. The Control Panel has a polycarbonate overlay, so cigarette marks and mars can easily be wiped clean. This overlay can be replaced if necessary. The Marquee and Coverglass are made of fully Tempered Glass to minimize breakage. The Back Service Door houses all the P C Boards for the system making servicing of the game, if needed, much easier. Lighted Instructions are provided to further enhance the game and attract players, by making the Instructions easier to read. TAITO AMERICA CORPORATION proudly presents our improved Self-Test capability, making servicing of the game easier, which keeps your game up and running with less down time.

1.2 INTRODUCTION TAITO AMERICA CORPORATION'S ‘‘SPACE DUNGEONS'’™ upright game is designed for one or two players. The object of the game is to search the ‘‘SPACE DUN- GEONS’’™ for treasure. The Dungeon consists of 99 levels or depths of a six by six matrix of squares or rooms with various doors through which the player and the adversaries may leave or enter The player's SHIP may move in eight directions. The Player has the ability to ‘RAPID FIRE” his own laser in eight directions to destroy the enemy while searching the rooms for treasure. Treasure points are scored by entering the COLLECT BONUS area which allows the player to descend to the next level or depth. Some treasures are guarded; thus providing more challenge. In some rooms there are CORNER ZAPPERS that fire laser shots into the space within the room increasing the danger for the player. PIKERS and DEATH- SQUARES will attempt to ram the player. EXECUTIONERS will attempt to shoot the player with highly accurate missiles. The THIEF will steal treasures from the dungeon, but he will drop the treasures if he is shot. A special bonus is awarded if the player completely explores an entire depth, but if the player stays on one depth for too long, the deadly ENFORCER appears. The player should exercise extreme caution in the vicinity of the SPORE CASE because if it is hit it will explode into deadly shrapnel.

1.3 GAME INSPECTION TAITO AMERICA CORPORATION'S “SPACE DUNGEONS’’™ upright game is shipped ready for operation, but a last visual check should be made to insure the game is in good condition. Please verify the following before turning the game on. Check the exterior of the game for shipping damage, chips, dents, or broken parts. Open the Rear Service Door and check for any interior damage. @ Make sure there isn't any damage to the wiring. @ Check Printed Circuit Boards, making sure there is no damage to the components. @ Check fuses making sure they are firmly in their holders. Check for loose foreign objects, especially metal objects which may cause electrical problems. © Check Plug-in Connectors making sure they are firmly in their sockets. @ Check Self Test Switches making sure they are not damaged. The Video Monitor is properly adjusted before shipping. If there are any adjustments necessary, refer to our Video Monitor Manual (72-00020-001) This Manual contains all the Manufacturers recommendations for adjusting the Video Monitor. 1.4 PRE-GAME INSTALLATION The following precautions should be followed when installing the game. Avoid rough handling of the game, the picture tube is fragile. @ Install the game on a level surface. Avoid installing the game where it may receive excessive sunlight or heat, to protect the game from rising internal temperatures. @ Do not install in a damp or dusty location. @ For a short time after connecting the power to the game, the picture may be temporarily distorted. The monitor's purity is affected by the earth’s magnetic field, causing a variation of color. By turning the game on for 10 or 15 seconds and then off for 20 to 30 minutes the automatic degaussing circuit applies a degaussing field around the edges of the monitor. Doing this several times will correct the problem. Another way to correct this problem is to purchase a degaussing coil or bulk tape eraser at any Electronics store. This will help to immediately demagnetize the Video tube. Caution must be used with a degaussing coil so the magnetic field of the degaussing coil is not allowed to become too intense at any one place on the picture tube thereby causing a localized color distortion. If you move the game to another location after degaussing the problem may reappear. Refer to Monitor Manual (72-00020-001) for details. 1.4.1 POWER REQUIRMENTS TAITO AMERICA CORPORATION'S “SPACE DUNGEONS’’™ game is shipped ready for operation at 120 or 240VAC, 60Hz with a Power consumption of approximately 250 Watts. The following line voltages may be selected: 100VAC + 10% 50/60Hz 120VAC +10% 50/60Hz 200VAC +10% 50/60Hz 220VAC +10% 50/60Hz 240VAC + 10% 50/60Hz

A voltage Programming Block is located on the primary side of the Transformer to compensate for high/low conditions. (See Figure 4-1).

FIGURE 1-1 PROGRAMING PLUG

Page 9
CAUTION For safe operation it is recommended the cabinet be grounded. This game is equipped with a three conductor power cable. The third conductor is the ground conductor and when the cable is plugged into an appropriate receptable, the game is grounded. The offset pin on the power cable's three-prong connector is the ground connection. Reset To Factory Setting (Reset Line Lit) Increment Number (Variable Line Lit) Decrement Number Move To Next Line (Will also get you into Electronic Diagnostics) Move To The Next Screen Down Advance Sub-Test

Advance Test

1.5 POWER ON/OFF SWITCH, INTERLOCK SWITCH, MEMORY PROTECT SWITCH, SELF TEST SWITCH, VOLUME CONTROL, AND SERVICE OUTLET To minimize the hazard of electrical shock while servicing the game a Power ON/OFF Switch, and two (2) Interlock Switches are provided. Two (2) Self Test Switches, two (2) Volume Control and a Service Outlet have also been provided. (See Figures 5 and 6 for the location of Switches).

1.5.1 POWER ON/OFF SWITCH, INTERLOCK SWITCH A Power ON/OFF Switch is located in the front of the game at the bottom right hand side of the cabinet. There is two Power Interlock Switches, one is located on the inside of the Coin Door frame and the other is located at the inside rear of the Service Door. This switch removes all the power from the game without unplugging it from the wall outlet. Power may be restored for servicing by pulling out on the Interlock Switch Button. \

FIGURE 1-2 POWER ON/OFF SWITCH 4.5.2 MEMORY PROTECT SWITCH The Memory Protect Switch is used to prevent erroneous writes to locations in the CMOS RAM which store the location program variables. This is the black button above the Power Interlock.

Coin Door Memory Protect Switch

Coin Door Powet Interlock Switch

Back Doot Power Intertcok Switch

FIGURE 1-3 INTERLOCK SWITCH & MEMORY PROTECT SWITCH 1.5.3 SELF TEST SWITCH There are two (2) Self Test Switches and four (4) positions, located on the inside of Coin Door. See Figure 1-4. The “SPACE DUN- GEONS''™ game is capable of testing itself and provides data to demonstrate that the games circuitry and the controls are working Properly. For further information on the Self Test Procedure refer to Section 1.8 and Figure 1-7. 7a mI oy at. ele we | FIGURE 1-4 SELF TEST SWITCHES oN SOEe TABLE 1-1 SELF TEST SWITCHES

1.5.4 VOLUME CONTROL SETTING The Volume Control Setting is located on the Data/Sound P. C. Board, which is on the Service Door. The volume increases when turned clockwise as indicated in Figure 1-5. A second volume control can be found on the inside right of the Coin Door frame. The volume incteases when turned as indicated in Figure 1-5.

FIGURE 1-5 VOLUME CONTROL SETTINGS

1.5.5 SERVICE OUTLET A Power Recepatacle has been provided to further aid servicing. The voltage at this receptacle will be the same as the line voltage the game is set at.

1.6 ELECTRONIC ACCEPTORS This game is equipped with the capability of using 12 VDC electronic Coin Acceptors, such as Third Wave Electronics, Model TW12 or equivalent. Power for these units may be obtained from the Coin Entry Lamp terminals which provide +12 VDC.

1.7 GAME INSTALLATION Qpen the Coin Door and pul! out the bottom Interlock Switch. Turn the game on. See Figure 1-3. The language selection frame should be displayed. ‘f the game is in the game mode, push the Self Test switch toward ADV SUB TEST. The game will go into Self Test. If after a minute, the switch test frame is not displayed, refer to the Manual on Self Test. After the Switch Test is displayed push the Self Test Switch toward ADV TEST four more times. The language selection frame should then be displayed. Push the Self Test Switch toward ADV SUB TEST until the language you want is green. Push the Self Test Switch toward ADV TEST and then all the print should be in the language you select. Push Self Test Switch toward ADV TEST four mote times the game should be in the game mode. For more information on the options the operator can use, see Section 1.8.17 thru 1.8.21

Page 10

1.7.1 GAME ADJUSTMENTS There are several adjustments you can make to the game to make the play easier or more difficult. First, Maximum Credits defines a limit for the machine, which when crossed will disable the coin slots. This will allow the location to set a limit on the amount of games a player will get if there is a line of people waiting. This value ranges from 1 to 99. However, it should not be set so close to 99 that a single coin can overflow the credits issued (maximum 99). A Free Play mode may be selected by setting maximum credits to 0. Next is the number of turns which regulates the number of ships on the playfield. This can be set from 2-6, factory default being 3. Next is the Name Registration for the high score list. ‘‘0”’ will disable Name Registration and a ‘1” will enable Name Registration when a player scores higher than the tenth (10) highest score. Factory setting is a‘“1"". The Bonus Increment can be set anywhere from 1-99, incremented at 1000 points. This is factory set at 10. The Difficulty factor can be set from 0-3, 0 being the easiest and 3 being the most difficult. The game play can be increased or decreased to make the game easier or more difficult to play. This is factory set at ‘1’. The Attract Mode Sound can be set for 0, no sound, or 1, Attract Mode Sound. This is factory set at 1, sound. Next is the Cocktail Table Mode, this should be set at 0, for upright operation, 1 for cocktail operation. The factory default is 0, upright.

1.8 SELF TEST PROCEDURE 1.8.1 GENERAL The Self Test Procedure is performed using the two (2) Switches located on the right inside corner of the Cabinet, and the SELF TEST Button and the LED'S on the Video PC Board. (See Figure 1-7).

FIGURE 1-6 SELF TEST BUTTON 1.8.2 ENTERING INTO THE SELF TEST MODE To enter the Self Test Mode, press the ADVANCE SUB-TEST Switch located on theCoin Door or the Self Test Button found near the LED display on the Video Board. Al! the LED'S should blink on and off and then Hardware Tests should start. If a continual test of the Video Board is desired, press the Self Test Button once and then again after all the LED’S blink off. in this mode, the machine will continually run the Hardware Test until powered off. If the message ‘OPEN COIN DOOR TO TEST’ appears, the Coin Door must he opened or a jumper connected across J19, 1-2. This is because the CMOS RAM Test cannot be performed with the memory protected in the ON position, by the Coin Door Switch. 1.8.3 HARDWARE TESTS These tests are performed in the following order:

VIDEO BOARD ROM Checksum Communications RAM DATA BOARD ROM Checksum Local RAM Communications RAM Handshake Test CMOS RAM Color RAM Screen RAM

TABLE 1-2 HARDWARE TESTS All LED values are shown Left to Right. 0 is OFF, 1 is ON and X is dependent upon the test results.

1.8.4 VIDEO BOARD ROM CHECKSUM The Rom Checksum calculates the checksum of each Video ROM and compares it to the checksum stored for that ROM. |f it differsfrom the stored value, the machine will halt and the value of the ROM with the bad checksum will be shown on the LED’S.

LED VALUES: TEST IN PROGRESS: FAILURE: 00 0001 01 XXXX

LED VALUE 01 0000 01 0001 01 0010 2732 A000-AFFF B000-BFFF C000-CFFF DO000-DFFF E000-EFFF FOOO-FFFF

TABLE 1-3 VIDEO BOARD ROM CHECKSUM If the Checksum ROM is bad, it will show U10 to be bad first. If this test fails, the ROM indicated on the LED display or the supporting circuits will need to be replaced. The E-PROM Memory ina given game may be implemented as banks of either 2716 or 2732 E-PROMS. The E-PROM type for each bank is selected by the decoding jumper 26-00002-016 for 2716 or 26-00002-032 for 2732. 01 0011 01 0100 01 0101

LOCATION E-PROM BANK VIDEO U1 DATA U22 SOUND u29

TABLE 1-4 DECODING JUMPER LOCATION

1.8.5 COMMUNICATIONS RAM FROM VIDEO BOARD The Communications RAM Test determines the stability of memory shared by the two processors by storing a predefined series of numbers throughout the RAM, then reading it back to insure that it was stored correctly.

LED VALUE: 00 0010

A failure has been detected when the machine halts with the above display. Failure of Communications RAM during Video Board Tests may result from either defective RAM circuitry or failure of the Data Board. To isolate the failure, disconnect the Data Board at J6 and re-enter the test. A failure means trouble in U3, U4 or associated circuits. Passing the retest suggests Data Board problems.

Page 11

1.8.6 VIDEO BOARD CMOS RAM After saving values in another portion of memory, the CMOS RAM is tested in the same manner as the Communications RAM. If the CMOS RAM passes the test, all of the locations are restored to their previous values.

LED VALUE: 00 0011

A failure of the CMOS RAM has been detected when the machine halts with the above LED value displayed. if this occurs U85 and U86 or associated decoding should be checked.

1.8.7 VIDEO BOARD COLOR RAM This tests the system Color RAM by storing predefined sequences of numbers in the Color RAM, then reading them back while testing for accuracy.

LED VALUE: 00 0100

A failure is indicated by the processor halting with the above value displayed on the LED'S. This signifies the need to check US6, U57 and associated multiplexing and decoding.

1.8.8 VIDEO BOARD SCREEN RAM The Screen RAN is tested by writing a pattern to each page on the screen. The results of these writes is then compared to the original pattern. Any discrepancy causes the machine to halt with the LED displaying the faulty RAM.

00 0101 1X XXXX TEST IN PROGRESS: FAILURE: LED VALUE:

LED VALUE | RAM 11 XXXX

70.0000| u3371 0000

10.0001} U32 11 0001

100010| ust41 0010
100011| u30110011
100100| 29{10100
100101| u28110101
100110| u2711.0110
toot| u2611 0ttt
toi000| ut711 1000
to 1001| ut614 1001
101010| U1511 1010
iorott| u1411 1011
101100| U13111100
4o1tor| u124141101

101110} unt iitto | u42 40 1111 [vio {ost | ua TABLE 1-5 VIDEO BOARD RAM CHECKSUM

Upon failure of ascreen RAM, locate the problem RAM and repiace it. Exchange suspected RAM with a known good location to determine if the problem moves with the RAM IC or whether the problem is in the supporting circuitry, further testing can be done with the Color Bar Test. Refer to (1.8.15). It this Diagnostic appears to hait without indicating a RAM failure (00 0101 on LED’S), and the test pattern was cleared off the screen, a failure to begin the next test (Data Hardware) is indicated. The interconnection to the Data Processor must be in place and the Data Processor must be functional to continue. SELF TEST LEDS

90 0000

‘SELF TEST BUTTON ° . | FIGURE 1-7 VIDEO BOARD (ON SERVICE DOOR)

1.8.9 DATA/SOUND BOARD SELF TESTS DATA HARDWARE (ROM CHECKSUM) The ROM Checksum calculates the checksum of each Data ROM and compares it to the checksum stored for that ROM. If it differs from the stored value, the machine will halt and the value of the ROM with the bad checksum will be shown on the LED'S.

LED VALUE: TEST IN PROGRESS: 00 0110

FAILURE: O14 XXXX

LED VALUE | DATA ADDRESS

01 0000‘A000-AFFFU14
01 0001BO00-AFFFU15
01 0010CO00-AFFFU16
01 00110000-AFFFUi7
01 0100C000-AFFFU18
01 0101FO00-AFFFUt9

TABLE 1-6 DATA/SOUND BOARD ROM CHECKSUM If this test fails in the field, the bad ROM will need to be replaced. To aid the technician in diagnosing difficult boards, hold the Self Test Button, located on the Video Board, depressed while the game is being powered on. This will cause the game to enter the diagnostic mode directly upon power up, accessing only one ROM per processor. Games which otherwise will not execute the on board diagnostics will thereby provide more information on ROM failure.

1.8.10 DATA/SOUND BOARD LOCAL MEMORY The Data processor uses a Known sequence of numbers to test the bits in its Local Memory. If a bad bit is found the machine will halt with the following display located at Ui5 and U16. LED VALUE: 00 0111

1.8.11 COMMUNICATIONS RAM ADDRESSING The function of this test is to ensure that both the Data and the Video Processor address the Communicatons RAM in the same manner. The Data Processor requests the Video Processor to fill the RAM with a known pattern then, the Data Processor compares the result to the expected pattern. If it does not match, one of the Processors is probably decoding the address incorrectly as the RAM itself was previously tested for stability by the Video Processor. The machine will halt with the following display.

LED VALUE: 00 1000 9

Page 12

1.8.12 DATA/VIDEO HANDSHAKE This test ensures that the Data Processor can send priority commands via interrupts to the Video Processor. The Video Processor is halted, then restarted by the data Processor after the proper command acknowledgements are received. The machine will halt with the following display at U6, U7, U8, U10.

LED VALUE: 00 1001

1.8.13 SWITCH TEST This screen is used to determine all switches are working order before entering the switch dependent self-test screens. The switch numbers appear in green if the switch is closed and white if it is open. The Advance Test Switch (Switch number 9) is always red in order to set it apart from the others on the screen, switch 29, 30, 31, 32 are used as outputs & stay green. The user should check all other switches before pressing the Advance Test Switch, as this would move him to the next screen. In addition to the switches required, by the game, the User should be sure to test the Advance Sub-Test, UP and DOWN Switches, located on the Coin Door for proper closure as these switches are used to move about in the Location Programming Screens. To advance to the next screen, activate the Advance Test Button located on the coin door.

GAME OVER

ADVANGE SELF TEST aoe NeST

(eseoR mow cnecxsuul oo ovo: — SN couuumicarions maw Y 09 0010 yivEo 5 Soano’ coron paw Y 00 2100

ow cnecxsum [00 or 10S kaa paras | tocar mau Yoo arts rouMt foand | communications mau 00 1000 MaMosHAKe TEST } 00 100

‘switew TEST nay acate coLon anne ALIONMENT- CONVERGENCE LAMQUAGE SELECT LOCATION PRoGrauina man scone 10 oATE SCREEN, Tests

com SLD PROGRAMMING

GAME OVER

FIGURE 1-8 FLOW CHART 1.8.14 COLOR BALANCE AND INTENSITY ADJUST SCREEN This screen is comprised of two sections. The first section provides a method for adjusting the intensity \evel of each color gun, and achieving an initial color balance. Three squares, one blue, one green and one red, are drawn along the top of the screen at minimum intensity or brightness. The color guns should be adjusted so that these squares are barely visible and of equal intensity. To complete the color adjustments, a gray scale is provided at the bottom of the screen. Fine tune the color balance with this scale, then double check that the squares at the top are barely visible. To advance to the next screen, activate the Advance Test a located on the Coin Door. $0000 1.8.15 COLOR BARS The CPU divides the screen RAM into 16 areas corresponding to 16 bars on the screen. Each area is written with a data value from the Table 1-7. Each value exercises one bit in the screen RAM. The Color RAM is written with a pattern which outputs each data value with a recognizable color from the table. All other data values are coded black. This results in a normal screen of 16 colors bars per the following Figure. 2, RS e, PyPoF of eo OC So s SY Sy SS eo So west Nt ‘a Sy KJ ae Pe AS Se Re ye a o ° oe & oe & po oF of SI o srrFF

COLOR BAR DIAGNOSTIC NORMAL FIGURE 1-9 COLOR BAR

BLK BLU BLK

Pus Sah aS a8 oe $0 PP Ororgh dart as o® SoS ms oH SS SR wey we ws wes oo 8 Ars fF “ep “ ROC swiss 22% Noy ‘SOOFF, SEE

COLOR BAR DIAGNOSTIC BIT 03 STUCK LOW IN 1-BANK FIGURE 1-10 COLOR BAR

Page 13

SCREEN RAM DATA CONTENT

° oot

COLOR BAR DIAGNOSTIC BIT § STUCK HIGH ALL BANKS

FIGURE 1-11 COLOR BAR SCREEN RAM CONTENT COLOR RAM ADDRESS

COLOR BINARY | BIT TESTED

Red01 |0000 00010
Orange02 |0000 00101
Yellow04 |0000 01002
Green08 |0000 10003
Blue Green | 10 |0001 00004
Blue20 |0010 00005
Violet40 | 0100 00006
White80 |1000 00007
RedFE111111100
OrangeFO}1111 11011
YellowFB}1111 10112
GreenF7 )1111 O1113

Green Blue | EF | 1110 1111 4

BlueOF | 1101 11115
VioletB7 |1011 11116
WhiteF7 | 0111 11117

Black XX | XXXX XXXX

TABLE 1-7

{f the Self-Test passes, errors in those circuits which affect CPU access are ruled out. This leaves latches U91-U94, shift registers U5, U96 and U105-110, direction select MUX U81 and U104 and the CR side of select U81 and U104 and CR side of the Color RAM MUX USS, U73, and U74. Stuck bits may be indentified by observing abnormal bars. A bit stuck high will result in black bars (two bit high) on the left half of the screen except for the bar associated with the stuck bit. On the right half, the bar associated with the stuck bit will be black. The converse is true of a bit stuck low. An error across the entire bar indicates an error in the shift registers, direction select, or color RAM MUX which affects every pixel. Lines of error running crosswise to the bars indicate an error in one bank of RAM if every eighth pixel. To move to the next screen, activate the Advance Test Button on the Coin Door. If self test fails, the color bars still may by useful. This screen May now be entered without going through on-board self test. Use “Advance Test’’ to enter the high score screen then “‘Down’’ to enter the Switch Test. Advance Test may then be used to access color bars. 1.8.16 ALIGNMENT AND CONVERGENCE TEST This screen is provided to align the color guns and correct the convergence on the screen. The screen is composed of a red anda green rectangle and white grid. Adjust the screen width and length so that the red rectangle is slightly within the boundaries of the tube. The adjustment is to be made on the center of the lines which make up the rectangle. The corners of the rectangle will extend beyond the shadow mask. The green rectangle defines the normal playfield and so should be visible from the players view point. A grid of white squares is provided to help detect and correct any convergence problems the tube may have. Adjust the monitor until the squares are of equal size throughout the screen. To advance to the next screen, activate the Advance Test Button on the Coin Door.

abl

Page 14

1.8.17 LOCATION SELECT SCREEN (LANGUAGE SELECTION) This screen allows the user to select the language in which the Location Select and the game will operate. Four (4) languages are provided. Use the Advance Sub-Test Button to move through the offered languages. When the desired language is green, depress the Advance Test Button, to advance to the next screen.

1.8.18 LOCATION NAME SELECTION This screen allows the user to program the location name. Alpha, numerical and miscellaneous characters are provided. Use the ADVANCE SUB-TEST Button to move to the next character position indicated in green. Use the UP/DOWN switch to reach desired character, set by depressing ADVANCE SUB-TEST BUTTON. Continue until location name is completed, depress ADVANCE TEST Button to advance to next screen.

1.8.19 LOCATION SELECT This screen allows the location to define various game control parameters. The User selects the line to be changed by using, the AD- VANCE SUB-TEST Button until the desired line is changed to green. The value associated with this line is then modified with the UP or DOWN switches. If the machine is to be reset to the factory setting, use the ADVANCE SUB-TEST Button until the reset line is lit in green, then press the UP switch. The values will be reset and the user will be placed back on the first line for further adjustments. Advance test will move to the next screen at any time. The maximum credits defines a limit for the machine, which when crossed will disable the coin slots. This allows the location to set a limit on the amount of games a player will get if there is a line of people waiting. This value ranges from 1 to 99. However, it should not be set so close to 99 that a single coin can overflow the credits issued (maximum 99). A Free Play Mode may be selected by setting maximum credits to 0. The credits per coin are set in the Coin Slot Selection Screen. (1.8.22). The number of turns defines how many turns per credit. This value ranges from 2-6. Table Mode defines what type of cabinet the game is in. Settings are 0 upright, 1 Cocktail Table . Attract Sound defines whether or not the User chooses to have sound produced from the machine during Attract Mode, having 1 as ON and 0 as OFF. The difficulty factor allows the user to set the difficulty from 0-3 using 1 as factory setting. HSTD (High Score to Date) enables the User to disable all HSTD functions, set at 1 for ON and O for OFF. Bonus turn allows the User to choose if a bonus turn should be awarded. 0 disables bonus. Other values set Bonus at that value times 1,000 points. 1.8.20 HIGH SCORE TO DATE SCREEN This screen shows the scores and initials of the players with the ten highest scores. It is used as an audit for the game. To reset the values, press the UP Switch. This will also set the initials to the default values. When the UP Button is activated it resets to default scores. To move to the next screen, activate the ADVANCE TEST BUTTON on the Coin Door.

1.8.21 AUDIT TOTALS This screen provides the audit totals for the game. Once they are recorded, they may be zeroed by pressing the UP Switch. The following audits are kept. The total number of paid credits issued. This total is never zeroed, but it will wrap around to zero when its total reaches 1,000,000. The only time this total can be zeroed is by physically removing the battery or jumper W1, while the power Total Credits

is off. Left Coins The number of coins dropped into the left slot. Center Coins The number of coins dropped in the center slot. Right Coins The number of coins dropped into the right slot. Paid Credits The number of credits issued for coins. Awarded Credits The number of credits awarded by the game during Free Play Mode. Awarded credits / paid credits + awarded credits * 100 Number of minutes the game has been in play mode. Number of minutes the game has been in extended or awarded play. '% Free Time Awarded minutes / minutes played * 100. Average Game (Sec) | Minutes played / paid credits total credits * 60. The number of times which a player scored high enough to bump someone else from the high score list. % Free Plays

Minutes Played

Minutes Awarded

High Scores

TABLE 1-8 AUDIT TOTALS

The UP Switch is used to zero the audits. To advance to the next screen, activate the Advance Test Button on the Coin Door. Total credits will not turn to zero unless battery voltage is removed from CMOS memory.

1.8.22 COIN SLOT SELECTION This screen allows the user to either select a standard coinage setting for the game or program his own. If a standard setting is desired, use the UP and DOWN Switch to adjust the coinage setting while it is lit in green. The values for the variable will change as this number is altered. When the right selection is set, use Advance Test te return to the game. if a non-standard setting is desired, use Advance Sub-Test Switch to move down to the variables so that they may be programmed individually. Once this switch is pressed, the setting number is set to zero to show that the location has supplied their own settings. As the lower variables are unchanged, the user may minimize his effort by first selecting a setting close to the one he desires. Once in the programming mode, the Advance Sub-Test Switch is used to move among the variables. It will also take you back to the standard settings, if you press it by mistake. The UP and DOWN Switches are used to increment or decrement the values. Advance Test Switch will return to the game when pressed. The coin multiplier tells how many coin units are issued for each coin through a particular slot. Coin units for credit show the number of units necessary before a credit is issued. Coin units for bonus gives the number of units necessary before a bonus credit is issued. Minimum coin is an optional value which will keep the credits from accumulating until the specified minimum amount of coin units is reached. It is not used in any of the standard settings.

Page 15

1.8.23 CMOS MEMORY FAILURE If the message ‘‘Memory Failure - Service Required” appears on the screen, the CMOS RAM which stores all of the location programming has failed. This condition probably indicates a battery failure, or a failure of U85 or U86. Refer to Section 2 on Maintenance 2.7.6 CMOS RAM.

STANDARD COIN SETTINGS TABLE 1-9

a3=4g2

els/*@|S|slsls

56/28)/8le;/S8/s8le COIN DOOR MECHANISMS GREDIT/MONEY

STANDARD17.25, 441or | or | 04 | ov | or | 00 | 00

11.50, 3/81, 6/82 o2 [01 | 04 | 01 | 2 | 04 | 00 17.50 3 | 01 | 04 | 01 | 02 | 00 | 00

1 DM, 5 DM1/1DM, 6/5DM04 | 06 | 00 | o1 | o1 | 00 | 00
1 FRANC, 5 FRANC1/2F, 3/5F ONLY05 | o1 | 16 | 06 | 02 | 00 | 00
25 CENTS, 1 GUILDER1/25, 41606 | o1 | 00 | 04 | 01 | 0 | 00
5 FRANCS, 10 FRANCSWSF, 2/10Fo7 | or | 00 | 02 | 01 | 00 | 00
1V10F08 | or | 00 | o2|02|00 | 00
1 FRANC, 2 FRANCQF, 5/2F9 | 00 | 04 | 01 | o4 | 00 | 00
1 UNIT, 5 UNITS172, 3/5to | or | 00 | 06 | o2 | 00 | 00
TWIN COIN11 COINor | o1 | o4 | or | or | 00 | 00
1/2 COINS03 | o1 | 04]ot | 02]00 | 00

CUSTOM COIN SETTINGS TABLE 1-10

.lZila

2=)=cfgZz

Els|e/e/s|sl\s

elelsls/e]2]e

&|3/8/2/8|8/s

COIN DOOR MECHANISMSCREDIT/MONEYin
| STANDARD1.25, 5/100 | o1 | 04]o1|01 | 04]00
2.50, 51oo]o1[04 | or | or]04 | 02
2.50, 441oo{or | 04]or | or]00}02
17.50, 391, 491.25oo] 03]12{ 03]o4|15]00
1.50, 3/81, 7/8200}12|48{12;14]96]24
25 CENTS, 1 GUILDER17.25, 5/1Goo | o1| 00 | o+|ot]o4 | 00
100 LIRE, 200 LIRE1/200 LIRE00|or}00|o2|02}00 | 00 |
TWIN COIN1/3 COIN, 2/5oo | o2[00 { 02]05]0 | 00
1 UNIT, 5 UNITS11, 55oo | or}oo | 05]0100]00
113, 2/500{oz]oof10]05]00]0
Page 16

NOTES

Page 17

Maintenance

ALL GAMES REQUIRE A CERTAIN AMOUNT OF MAINTENANCE TO KEEP THEM IN GOOD WORKING ORDER. A PERIODIC CHECK OF THE MECHANICAL CONTROLS WOULD BE BENEFICAL TO THE SUCCESS OF YOUR GAME.

Page 18
  • MAINTENANCE AND REPAIR 2.4 MONITOR REMOVAL ; 2.1 CLEANING If you need to remove the Video Monitor, follow the instructions The exterior of the game, all metal parts and all plastic parts canbe _listed below: cleaned with a non-abrasive cleanser. Caution should be used when cleaning the glass, a dry cloth can cause scratches and result CAUTION in a foggy appearance. It is recommended the game be left disconnected for at least one hour before removing the Video Monitor. 2.2 COIN DOOR This will probably discharge the Video tube but EX- The Door used in “SPACE DUNGEONS’’™ UPRIGHT game needs TREME CAUTION is still necessary. little or no maintenance, See Figure 2.1. If desired a special coin mechanism cleanser, that leaves no residue, can be obtained from 1. Disconnect power from the line voltage. your distributor. Refer to the manufacturers documenation if addi- 2. Remove the Control Panel by releasing the two spring tional information is needed. loaded latches.
  • Open back service door. 4, Disconnect the Wiring by separating connector V and all wire to the CRT.
  • Remove the two (2) side bolts, one (1) on each side of the cabinet.
  • Lower the Monitor on the side rails.
  • Remove (4) screws, one on each corner of the Monitor, lift the monitor up and out of the cabinet.
CAUTION Use EXTREME CAUTION and do not touch electrical parts of the Monitor Yoke area with your hands or with any metal object in your hands! High voltages may exist in any Monitor, even with power disconnected.

FIGURE 2-1 COIN DOOR

2.3 FUSE REPLACEMENT This game contains eight (8) fuses. Five (5) fuses can be found on the Regulator PCB and two (2) can be found on the Transformer Assembly. One (1) fuses are located at the bracket where the AC line cord comes into the cabinet.

FIGURE 2-3 MONITOR REMOVAL

CAUTION
Caution must be used with a degaussing coil so the Magnetic field of the degaussing coil is not allowed to become too intense at any on place on the picture tube thereby causing a localized color distortion. FIGURE 2-2 FUSE REPLACEMENT

If you move the game to another location after degaussing the problem may reappear. Refer to Monitor Manual 72-00010-001 for further details.

Page 19

2.5 COVER GLASS REMOVAL To remove the Cover Glass follow the instructions listed below:

  • Remove the contro! panel by reaching up through the Coin Door and unlatching the latching clamps.
  • Remove the (3) Screws on the Cover Glass Bracket.(See Item 2)
  • Remove the (3) Screws on the back Cover Glass Bracket. (See Item 3)
  • Hold Glass firmly and lift up and out.
  • Be sure you are holding the giass firmly to ensure against any chipping or breakage.

FIGURE 2-4 COVER GLASS REMOVAL

2.6 PRINTED CIRCUIT BOARD REPLACEMENT You may wish to remove ‘‘SPACE DUNGEONS’’™ printed circuit board, Video Processor (08M00001-001), Data/Sound Board (08M00002-001), or ROM/IO Board (08M00027-001) for servicing. Refer to Figure 2-5. “SPACE DUNGEONS'’™ Printed Circuit Boards (PCB) are located on the inside of the service door for easy access. To remove the boards the following steps should be followed:

  • Open the Service Door, the power will automatically be removed by the Interlock Switch located on the inside of the door frame.
  • Disconnect the connectors from the board or boards you wish to remove.
  • Disconnect the ribbon cabie, connecting the boards by spreading eject latches on the connector.
  • Remove the screws for the boards you wish to remove. oe ll =

FIGURE 2-5 PRINTED CIRCUIT BOARD

2.7 POWER SUPPLY The Power Supply produces al! the necessary game voltage requirements. Refer to the Power Supply Schematic while reading the following circuit description.

FIGURE 2-6 POWER SUPPLY

2.7.1 AC INPUT The AC Input Voltage is applied to the main Power Supply via the AC Line Cords, Line Filter, Line Fuse, Power Switch and Interlock Switch. Different Line Cord are used for 120V and for 240V. The Line Fuse is located on the Line Cord Assembly near the Strain Relief. A Voltage Programming Block is located on the primary side of the Transformer to compensate for high/low voltage conditions. The following line voltages may be inserting the appropriate Programming Plug.

Line Voltage 100 VAC + 10+4 Line Fuse

3 AMP 50/60Hz 120 VAC + 10+4 | 50/60Hz 3 AMP 200 VAC + 10+4 | 50/60Hz 1.5 AMP 220 VAC + 10+4 | 50/60Hz 1.5 AMP 240 VAC + 10+4 | 50/60Hz 1.5 AMP.

TABLE 2-1 LINE VOLTAGE V7

Page 20
CAUTION For continous protection against fire hazard, replace only with a fuse of the same type having the same electrical rating.

There are five secondary sources. Three go to the Regulator PCB providing +5VDC, +12VDC, —12VDC, and —5VDC. The other two are fused 6.3VAC used for the incandescent lighting and fused 120VAC used for the monitor, and in certain models for a fluorescent lamp and fan. These secondary fuses are located on the bracket adjacent to the Power Transformer.

[cincuiT —_—_—i|. SECONDARY FUSE 120VAC 2.0AMP SLO-BLO 6.3VAG .SAMP

TABLE 2-2 SECONDARY FUSES

2.7.2 —5VDC AND —12VDC REGULATORS The AC Input for the negative voltages comes into the Regulator PCB on J1-5 and J1-6 from the Transformer. Fuse F3 protects against short circuits. The AC voltage is then full wave rectified by BR3 and filtered by C16. The raw DC is then applied to Reg 1, a three terminal —12V Regulator. The output of this Regualtor is the —12VDC output for the system and is also the input voltage for Reg 2,a —5V Regulator. The output of this Regulator is the —5VOC for the system. Capacitors C17, C18, C19 are to improve the transient response and stability of the minus voltage regulator. Diodes D8 and D9 provide protection against C18 and C19 being shorted through the Regulator. Resistors R34 and R35 provide current limiting for LED'S 3 and 4 which will light when there is some voltage present at the regulation outputs.

2.7.3 +5VDC REGULATOR The AC Input for the + 5VDC Regulator circuit comes in on J1-1 and J1-2, via Fi into BR1. BRi1 full wave rectifies the AC Input. This raw DC is applied to the collectors of (2) series pass transistors, mounted on the Heat Sink Assembly. The regulation is done by U3, which is a voltage regulator whose output controls the gain of Q5, which in turn controls the gain of the series of pass transistors. The emitter of the series pass transistor return to the Regulators PCB and through R11 and R12, which serve to force current sharing between the series pass devices. The veltzge at the output of R11 and R12 are the +5VDC for the system. R16 and R18 are voltage set and current foldback adjustments respectively. These are factory adjusted to 5V + .25V at 3.5 AMPS. Q8, D3 and R20 comprise a SCR-Type Crowbar Circuit which will trigger when the DC output voltages rise above 5.8V. Once the SCR fires, the Power Supply has to be turned off to reset the device. R19 is a current limiter for the voltage indicator LED 1. R16 is used to set the output voltage of the Regulator. C8, D2, R13 and O4 delay the start-up of the 5V Regulator to allow the —5VDC Regulator to stabilize first. 2.7.4 + 12VDC REGULATOR This circuit is essentially the same as the 5V Regulator described above. The AC current comes in on J1-3 and J1-4, via fuse F2 into BR2. The AC is rectified by BR2 and filtered by C9. The raw DC is fed toa single series pass transistor on the Heat Sink Assembly and also powers the +12V and +5V Regulator. R28 and R25 are voltage set and current foldback and factory adjusted to 12 Volts +.25V at 4 AMPS. D7, Q9, and R31 are SCR Crowbar Circuits which trigger at 13VDC output which causes supply to go into current foldback. There is an RC delay as in the 5V circuit to delay the +12V rise time.

2.7.5 RESET CIRCUIT The reset circuit will output a 2sec active low MRST pulse at J3-14 J4-14 when the power is first turned ON and whenever power fails for more than 35ms. The reset circuitry is comprised of a Dual Timer (556) and a fullwave type optical coupler across an AC secondary. The output of U1 is the input to one half of the 556 which is configured as a missing pulse detector. C1 and R3 determine the time before the output goes active. This is set for about 35ms. When two or more cycles are missing, the output of the first timer triggers the second timer which drives the MRST low for about 2 seconds. The timer constant for the second timer is set by R4 and C6. Power on reset is generated by C4, and R39 and D12 on the trigger input of the second timer. 3 inverts the signal out of the 556 so it is active low. R7 insures MRST is low while the power is rising.

2.7.6 POWER SUPPLY ADJUSTMENTS VOLTAGE Adjust voltage on +5V and +12V for +5.00V to +5.05V and +12.00V to +12.05V. CURRENT LIMIT Adjust control (5!, 121) counterclockwise until voltage just changes then turn control clockwise until voltage goes back to original value. With pointer, mark position of arrowon potentionmeter then turn control until beginning of 1st notch is aligned with the pointer. On the controls with the Blue Disk turn approximately 30 degrees.

FIGURE 2-7 CURRENT LIMIT ADJUSTMENT

If voltage adjustment will not bring voltage up, set current limit adjustment to 1/2 value.

Page 21

2.8 CMOS RAM If when powering the game up, it will not coin up because the battery is low, the following procedure should be followed. Open the Service Door of the game, pull interlock to power up the game and pull W1 out on the Video Board (Blue jumper). Turn the power off via the interlock. Wait 2 minutes, power back on and insert W1 back in. If the Language Select frame does not come on the CRT, power down, remove W1 again. Short pins 18 and 9 on U85, power back on and insert W1 back in. Leave the game on for 12 hours. If this procedure does not work when you turn the game back on the battery may need to be replaced.

2.9 TEST POINTS The following is a list of Test Points to be used when troubleshooting.

DATA/SOUND

DE (Master Clock) DQ (Master Clock) DMA/BREQ SA 15 (Address Line) DA 15 (Address Line) Voice Clock SBSC (Sound Processor Data Enable) DBSC (Data Processor Data Enable) +5V Ground

TABLE 2-3 DATA/SOUND BOARD TEST POINTS

VIDEO BOARD

Invert 10 MHZ va (Clock Video Processor) VE (Clock Video Processor) Lic Last Instruction Complete DMA/BRK

VBSC (Video Data Enable)

VA 15 (Address Line)

TABLE 2-4 VIDEO BOARD TEST POINTS

If you ground any Data Enable Test Point (DTP7, DTP8, VTP7) the related processor will receive NO OP and the address line will act like a 16 Bit Counter.

Page 22

NOTES

Page 23

Operation

THIS SECTION PROVIDES A TECHNICAL DESCRIPTION OF THE “SPACE DUN- GEON’’™ GAME. THE GAME ELECTRONICALLY CONSISTS OF PRINTED CIRCUIT BOARDS, POWER SUPPLY, AND SPEAKERS WHICH ARE DESCRIBED IN DETAIL IN THE FOLLOWING TEXT.

Page 24
  • THEORY OF OPERATION 3.1 GENERAL The TAITO AMERICA CORPORATION’S arcade video system game is an advanced multiprocessor based circuit utilizing the Motorola 6809E microprocessor. The system is organized in three logical blocks:

A. The Data Processor, which supervises the operation of the entire system. B. The Video Processor, which performs all screen based functions, such as playfield image motion, line drawing, etc. C. The Sound Processor, which generates sounds under the direct control of the Data Processor. In order to facilitate easy inter-system communications, the Data and the Video microprocessors run synchronously using clock and timing signals developed on the Video Board. For this reason, discussion will begin by examining the Video Board.

3.2 VIDEO BOARD 3.2.1 SYSTEM CLOCK : The fundamental system clock is developed by the 20MHz crystal, inverters U24 and U39, and components. The 20MHz signal is divided by the high speed flip flop U38 to obtain a 10MHz main clock with a precise 50 percent duty cycle. This 10MHz signal generates all other fundamental timing signals for the video system, including the Data Processor. 1C23 divides the 10MHz signal to obtain 5MHz, 2.5MHz and CCLK, and their respective inversions. \C’s U9, U37, and U38 combine these signals, presenting them to U25, which synchronizes the output signal to the system 10MHz clock. This circuit produces waveforms whose active edges are synchronized to 15ns worse case, 2ns average. The characteristics of the clock circuit may be noted by reference to the Timing Diagram, Fiaure 3-1.

' \ ome J \ swear | 7 1 \ . asa r 7 use I com IT ° i \ a 4 7 _ . 7 5 f 1 r

m i v amr LL wo P | co 7 + as . is “T\ i sous onus = =

it FIGURE 3-1 CLOCK TIMING 3.2.2 SCREEN RAM The Video Processor controls a Screen RAM of 256 x 256 pixels with 8 bits per pixel. In order to access this information, the screen is divided into two pages, top and bottom, chosen under software control. These pages are both addressed at 0000 - 7FFF with address 0 corresponding to the lower left corner of the screen (horizontal scan). All CRT accesses to this RAM are transparent to the processor and the RAM may be read or written any time. The timing of the Screen RAM and the eventual scan is controlled by a 6845/6545/46505 CRT Controller Chip. It's address outputs are gated by U19, U20, U50, and U51 for inversion when when in cocktail table mode. The scan addresses are multiplexed with the address present on the microprocessor data bus by U35, U52, U53, and U54 for standard RAS-CAS accessing. The desired bank of memory is addressed by U87, a one of four decoder. Data written into the Screen RAM comes directly from the system data bus, buffered by 33 Ohm resistors. If a processor read is taking place, the data is placed on the data bus by U77, U78, U79, and U80. Screen reads are latched by 374’s U91, U92, U93, and U94. A second screen read is then performed, and this data, together with the data from the screen read previously performed and latched by the 374’s is presented to the eight (8) 74.S299 shift registers. These registers may be shifted in either direction for cocktail table implementation. The byte stream then proceeds to the Color RAM.

VIDEO BOARD MEMORY MAP Dual Port RAM CMOS Battery Backup Memory LED Output and Color RAM Page Select Data FIRQ Activation Address Video FIRQ Deactivation Address Color RAM Address Latch Hi-Byte Address Latch Lo-Byte Address Latch Indexed Screen Location Scan Line Readback Location CRT Controller Base Address

TABLE 3-1 VIDEO BOARD MEMORY MAP

3.2.3 DUAL PORT RAM This RAM may be accessed in its entirety by either processor. This is arbitrated as follows:

  • The Data Processor runs in quadrature with (one quarter clock cycle ahead of) the Video Processor. In other words, E is inverted for use as DQ, and Q becomes DE. Refer to Timing Diagram. Figure 3-2.
  • The Data Processor, by nature of this timing, accesses the Dual Port RAM +2 cycle before the Video Processor. At this point the Video Processor is guaranteed to not be accessing the RAM. The Data Processor access is flagged by U36, which causes a cycle tobe stolen from the Video Processor’s main clock, VQand VE.
  • The Video Processor is unable to access the Dual Port RAM unless the Data Processor is not accessing it as it will not be receiving clocks during that time. The cycle steal is accomplished by the generation of signal DPMUX by U36. This signal directly steals the cycle, and also folds over multiplexers US, U6, and U21, switching the address lines, R/W and gating signals. U1 and U2 gate the data to or from the desired processor. U22 insures that no spurious writes are generated during foldover.
Page 25

: 4 [a So a T Pe

a, {——— mes f i 1 r FIGURE 3-2 DUAL PORT RAM TIMING

3.2.4 CMOS RAM The CMOS RAM is implemented for use as both a battery back-up storage area and a work area for the Video Processor. The gating U100, U101, U102, and U103 insure that writes to the block RAM from $8700 - 87FF cannot be performed unless the Coin Door is open (J19-2 grounded). The 3.6V NiCAD battery is trickle charged by Q8, R64, and R65 when the system is powered. When turned off, supply current for U85, U86, and U100 is provided by this battery. U100 is included to solidly gate the MRST signal and prevent invalid operations during power Up and Down. LED and Color RAM Page Latch, U72is addressed at address $8800. The upper six bits drive LED'S on the circuit board for diagnostics which cannot be done through the screen. The lower 2 bits select the Color RAM page and will be discussed later.

3.2.5 BI DIRECTIONAL FIRQ CAPABILITY To provide for immediate intet-system communication on demand a Bi-Directional FIRQ Capability has been provided. Any access of address $8C00 by the Video Processor will generate a FIRQ to the Data Processor. Any access of $8C01 by the Video Processor will remove a FIRQ generated by the Data Processor to the Video Processor. This is accomplished by U7, U8, and U9.

3.2.6 COLOR RAM The Color RAM is used as a translation matrix so that a number of different pixel values may access a given color, or to change the color of a given area of the screen without rewriting the Screen RAM. The serial bit stream, eight bits wide, comes from the shift registers of the Screen RAM to be presented to multiplexers U55, U73, and U74. These select between the Video Processor bus and the serial bit stream. As processor access times are considerably greater than the basic bit time (200ns), it is necessary to access this register only during retrace times. Bus read/write occur through U75, and serial output is latched by U76. This Data Stream is converted to a color pallet of 64 colors and four intensities. When the serial bit is selected for access, the two high order bits are provided by the LED output latch. This allows the Programmer to select between four pages of RAM rapidly. 3.2.7 ADDRESS LATCH CIRCUITRY Two methods of Screen Memory Address are provided:

  • A 16 bit address may be written into latch U70 and U7? addressed at $9402 and $9403. The addressed location may be accessed by reference to location $9400.
  • The high order bit of the latch selects one of two pages which May be directly addressed by reference to locations $0000 - $7FFF. U36, U70, and U71 latch the address. U36 is used in conjunction with U70 as U70 and U71 are tri-stated when inactive. The screen address deposited on the LA bus by U84 and U98 for Processor Bus accesses, and by U70 and U71 for latched address. Decoding is performed by U87 and U88.

3.2.8 SCAN LINE READBACK When read, this location is the number of the scan line currently being drawn by the beam. U34 latches the last row address drawn, and U101 prevents erratic updating at the end of a horizontal line. There are 256 valid scan lines 00 - FF.

3.2.9 CRT CONTROLLER The 6845/6545/46505 is a software programmable sync and scan generator. It has two ports based at $9C00 and $9C01. It is recommended that the reader consult Motorola, Hitachi, Rockwell, or Synertek supplied documentation. Register initialization is as follows:

Register | Description Initialization (decimal)

ROHorizontal total-138
R1Horizontal displayed32
R2Horizontal sync position34
R3Sync pluse width03
R4Vertical total-131
R5Vertical hold adjust1
R6Vertical displayed30
R7Vertical sync position30
RQScan lines per row-107

TABLE 3-2 REGISTER INITIALIZATION

All other registers are cleared. The interlace capability which differentiates the various types is not used in this application.

3.3 DATA‘SOUND BOARD The Data Processor runs synchronously to the Video Processor, as was described in this (Section Dual) Port Memory. All basic timing signals originate on the Video Processor Board and are bussed

  • onto the Data Processor Board. The Sound Processor and Amplifier circuitry also resides on this Board.
Page 26

3.3.1 MEMORY MAP The following devices are available for access to the Data Processor.

Dual Port Memory Local Memory ACIA Base Address Video FIRQ Activation Address Data FIRQ Deactivation Address Sound PIA Game PIA 1. Game PIA 2. Game PIA 3.

TABLE 3-3 DATA/SOUND MEMORY MAP

3.3.2 DUAL PORT MEMORY See discussion of Dual Port Memory under Video Processor Heading (Section 3.2).

3.3.3 LOCAL MEMORY This is a 1K block of memory, U15 and U16, provided for scratch and work area for the Data Processor.

3.3.4 ACIA A Motorola 6850 ACIA has been provided for diagnostic and other communications. Timing is generated by crystal oscillator Y1- U23 and prescaled by U27 and U26. SW1 may be configured to allow one of eight baud rates (2 speeds may be software selected in the ACIA). Correct RS-232 levels are provided by U25 and U21.

3.3.5 BI-DIRECTIONAL FIRQ CAPABILITY Any access of $8C00 will generate a FIRQ to the Video Processor. Any access of $8C01 will remove FIRQ generated by the Video Processor to the Data Processor. This is accomplished by U7, U8, and U9, which resides on the Video Board.

3.3.6 SOUND PIA Both ports of PIA U20 have been dedicated to the control of the Sound Processor. Port A is used to select a sound number, which is initiated by strobbing the U20 (CA2) - U8 (CA1) interrupt line. Responses can be made using the reverse U8 (CA2) - U20 (CA1) interrupt. Port B is used to control the amplitude of the generated sound to two Stereo Amplifiers. The output of side B goes to U24 and U28, which vary the ratio of the voltage divider across the non-inverting inputs of U29 and U30. This allows spatial positioning of a sound to coincide with real time events occurring on the screen, as well as a time based envelope control.

3.3.7 GAME PIA’S Three 6820's are provided for interfacing with Play Controls and Coin Door Switches. These are located on the Game Board and are accessed through a Jumper Cable J16 and J15 respectively. 3.3.8 SOUND PROCESSOR A Motorola 6802 also resides on the Data Board for sound generation. This Processor runs at 3.68MHz and accesses only two devices, PIA’S U7 and U8. U8 as mentioned previously, interface to the Data Processor. It also is the digital to analog output of the Sound Processor. Data from Port B is presented to U13. The current based output is converted to a voltage output by Q1, and controlled in amplitude by a potentiometer placed across J8. Speech circuitry is mixed with sound by R9, and the sum is sent to the Amplifiers. U7 controls the speech synthesis chip U19. The speech signal is shaped and filtered by the multipole bandpass filter U18.

3.4 ROM//0 BOARD This board contains the Program ROM for both the Data, Video and Sound Processors, along with the PIA'S needed to interface control, coils, iamps, etc.

3.4.1 GAME PIA’S Three Game PIA’S are located on this board $9400, $9900, $9C00. These devices, U11, U20, and U30 respectively, interface through Noise control circuits A or B filters for those lines dedicated to inputs. Eleven (11) High Current Drivers have been provided utilizing circuit C. Each of these is capable of switching a 1.5AMP/ 24Volt DC load to ground.

3.4.2 ROM’S Eight ROM locations are provided for the Data Processor, U12 - U19. These are selected by U21. Eight ROM’S, U3 - U10 selected by U2 are dedicated to the Video Processor. Sounds are supported by ROM'S U25, U26, and U27, with select U28. ROM Bank U3 - U10 may consist of either 2716 or 2732 type EPROMS as determined by a jumper plug inserted in U1. It is assumed that all such EPROMS in the bank are of the same type. Likewise, ROM Bank U12 - U19 is determined by jumper plug at U22 ROM Bank jumpering for 2716's is as follows: Pin 1-14, 2-13, 3-12, 4-11 and 5-10. The highest address EPROM is U10, U19, or U27 in each bank with addresses of adjacent sockets progressing downward in $800 byte blocks. Jumpering for 2732's is as follows: Pin 2-14, 3-13, 4-12, 5-11, and 6-10. The highest address EPROM is U10, U19, or U27 in each yank with addresses of adjacent sockets progressing downward in $1000 byte blocks.

Page 27

Illustration

&

Parts Lists

Page 28

INCANDESCENT PANEL

TAITO ITEM PART NO. DESCRIPTION 1 27-00006-001 | Lamp #47 2 26B00009-001 | Bayonet Socket 3 61D00112-001 | Marquee Lighting Plate

Page 29

8 WAY JOYSTICK

TAITO lo ITEM PART NO. DESCRIPTION 1 63B00071-001 | Ball & Shaft 2 63-00074-001 | Mask 3 63C00069-004 | Mounting Plate 4 63A00073-001 | Spacer 5 62C00004-001 | Shock Mount Pad 6 61A00227-001 | Spacer, Metal 7 58-00006-001 | Spring 8 63C00028-001 | Switch Plate 9 51-01002-011 | Screw 6X1 PRPH 10 63A00075-001 | Actuator "1 59-00020-019 | E-Ring 12 51-01001-006 | Screw 4X¥% PRPH 13 61A00018-001 | ‘‘L" BRACKET 14 29B00016-002 | Leaf Switch 15 51-01001-009 | Screw 4X3 PRPH 16 63A00026-001 | Spacer, Switch —|

Page 30

CONTROL PANEL

TAITO PART NO. DESCRIPTION 29B00016-001 Leaf Switch 54A07001-008 Nut, Stamped 63B00025-001 63B00024-001 Push Button Housing Push Button, White 42B00108-001 Cleat 63-00092-001 8-Way Control 61-00015-001 Strike Hook 42000017-001 61D00247-001 Control Panel, Wood Control Panel, Metal 63000091-001 Lexan

Page 31

CONTROL PANEL

Page 32

DOOR ASSEMBLY

TAITO PART NO. DESCRIPTION 42-00134-001 Back Door _ [oamoooc1-001 Video P.C.B. 08M00027-001 ROM/I0 P.C.B. W/PROMS 08M00039-003 Coin Door Processor W/PROMS 08M00002-004 Data/Sound P.C.B. 61D00079-001 P.C.B. Mounting Plate 61A00111-001 Bracket, Lock Rod 61B00142-001 Lock Rod Assembly 45000002-001 Lock Assembly Includes The Following +*|OlelN|olalslofrm}a 45B10001-001 Lock Barrel 45B02001-001 Lock Cylinder 45B03001-002 Key 45A04001-001 = Cam, Stop 04M00037-002 Lock Kit Includes The Following 45-00002-005 Nut %/:6 24N6 45-00002-006 Washer */16 External Tooth SPW4 45-00002-004 Plate, Anchor AP1 45-00002-009 Nut % 24N1 08-00042-001 P.C.B. Set Includes Items 2,3, And 5 12" 09-00234-002 Main Harness 09-00002-001 50 Pin Ribbon Cable (long) 09-00001-001 50 Pin Ribbon Cabie (short)

  • ITEM IS NOT SHOWN ON DRAWING.
Page 33

DOOR ASSEMBLY

Page 34

COIN DOOR

TAITO ITEM PART NO. DESCRIPTION 1 07-00027-001 | Inner Panel With Levers Sub Assy. 54-03013-001 | Nut #8-32

  • 09-00017-001 | Custom Harness Assy. (SGL Coin)
  • 09-00017-002 | Custom Harness Assy. (Dual Coin) 3 61B00113-001 | Service Switch Bracket 4 29-00022-001 | Service Switch 5 54-03011-001 | Nut #4-40 6 63-00014-001 | Switch Cover 7 §1-02052-001 | Screw #6-32X3/16 SS PH 8 23-00001-001 | C.R.£.M. Coil Assembly f 9 51-02052-001 | Screw #6-32X3/16 SS PH 10 59-00019-001 | Retainer 11 28-00029-001 | Silver Switch Wire For U.S. .25 12 29-00007-001 | Switch 13 61-00044-001 | Coin Chute 14 61-00045-001 | Coin Return Box 15 61-00025-001 | Switch & C.R.E.M. Coil Bracket 16 59-00018-001 | .25 Acceptor 17 §1-02051-006 | Screw #4-40X3/8 SS PH 18 27-00003-001 | Minature Bayonet Base Lamp
  • 26-00006-001 | Lamp Socket 19 27-00008-001 | #1815 Lamp (12 Volt) 20 61-00048-001 | Coin Inlet Chute 21 61-00047-001 | Right Half of Coin Inlet Chute 22 54-00001-001 | “‘U’' Type Fastener 23 51-02051-006 | Screw #4-40X¥2 SS PH 24 29-06006-001 | Slam Switch Assembly 25 998325 Coin Meter
  • ITEMS NOT SHOWN ON DRAWING.
Page 35

COIN DOOR

Page 36

COIN DOOR

TAITO EM PART NO. DESCRIPTION 1 61-00042-001 | Coin Door Only (2 Coins) 2 07-00023-001 | Coin Door Return Button Assy. For U.S. .25 Coin 3 63-00015-001 | Coin Return Button 4 79-50004-001 | U.S. .25 Price Decal 5 63-00016-001 | Coin Return Button Cover For U.S. -25 Coin 07-00025-001 Lock Assembly 07-00025-001 Lock Assembly 51-01051-003 Screw #4-/16 SL PH Type B 51-01051-003 Screw #4-5/16 SL PH Type B 63-00011-001 Coin Button Housing 51092051-002 Screw #4-40X%4 SL PH 63-00012-001 Coin Return Bezel 63-00013-001 Coin Return Cover 61-00040-001 Coin Door Frame 11 % X 13 % Mounts in a 10 % X 12 */16 Opening 54-01005-001 Hex Nut 14-20

51A03003-113 Carriage Bolt 07-00026-001 Lock Arm Assembly

Page 37

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 38

CABINET ASSEMBLY FRONT VIEW

TAITO

ITEMPART NO.DESCRIPTION

1 07M00055-006 | Light Box Assembly 2 63-00006-003 }''U"' Channel

347-00012-011|Marquee, Screened

4 61-00115-001 | Marquee, Retaining Bracket 5 61D00012-001 |‘‘Z" Bracket, Coverglass Lower 6 07M00052-003 | Control Panel Assembly 7 07-00115-001 | Coin Door w/Counter 8 61B00113-001 | Service Switch Bracket

929-00022-001|Slide, Center Return Switch

10 07M00057-001 | Service Switch Assembly Includes. Items 8 And 9. a 29B800015-001 | Interlock Switch

  • 59-00046-001 | Interlock Switch Barrier 12 61B00114-001 | Interlock Switch Bracket
1359-00008-001|Latching Clamp

14 63B00002-004 |“‘T'' Molding 15 29A00023-001 | Power On/Off Switch 16 41D00015-006 | Finished Cabinet

1761-00212-001|Volume Control Bracket

18 11-60002-502 {Volume Control Pot.

  • ITEM NOT SHOWN ON DRAWING
Page 39

CABINET ASSEMBLY FRONT VIEW

Page 40

CABINET ASSEMBLY REAR VIEW

TAITO (TEM PART NO. DESCRIPTION 1 21-00003-001 | Speaker

  • 09-00006-001 | Speaker Cable 2 61B00009-001 | Speaker Grill 3 41-00015-006 | Finished Cabinet 4 63D00035-001 | Monitor Shroud 5 47-00013-010 | Coverglass, Screened 6 27-00006-001 | #47 Lamp 7 26-00010-001 | Lamp Socket 8 07M00042-001] A/C Line Cord/Filter Assy. 7 59-00045-001 | Interlock Switch Barrier 9 61B00030-002 | Interlock Bracket, Single 10 29B00015-001 | Interlock Switch 11 63-00005-004 | ‘‘L’’ Molding 12 63-00005-012 | “‘L’’ Molding 13 08-00007-001 | Regulator P.C.B
  • 18-00003-001 | Transformer 7 07-00041-001 | Heatsink 14 61C00054-001 | Cash Box Lid 15 61D00060-001 | Cash Box 16 63R00010-001 | Cash Box Tray (Only) 17 63-00019-001 | Cash Tray Separator 18 61B00039-001 | Cash Tray Handle 19 07M00054-001) Cash Tray Assembly 20 42-00013-001 | Wood Cleat 21 61-00208-001 | CRT Wire Form Mounting 22 31-00012-001 | 19” Color Monitor (Vertical) 23 61-00006-001 | Bracket, Coverglass Upper 24 SEE FIGURE 4 | Back Door 25 44-00001-001 | Wheel Assembly ° 26° 79-50017-001 | Instruction Card
  • ITEMS NOT SHOWN ON DRAWING.
Page 41

CABINET ASSEMBLY REAR VIEW

Page 42

REGULATOR P.C.B. COMPONENT LAYOUT

es

FL 08-00007-001 MADE IN U.S.A. BRS l

Oa Ba QE) 0 Dog Wy Ce 2]

sas atell age | port © cle

+51 +5V +12v +20

arr ERO) cD ‘Our

Page 43

REGULATOR P.C.B.

TAITO SYM | PART NO. DESCRIPTION R1 | 11-00001-102 Resistor 1.0K 5% YaW 5% TAITO SYM | PART NO. DESCRIPTION C5 | 12-10001-102 Capacitor, .001uf R2_| 11-00001-512 Resistor 5.1K %W 5% C6 | 12-30001-106 Capacitor, Tantalum 10uf R3_| 11-00001-183 Resistor 18K %W 5% C7 | 12-20003-509 Capacitor, Electrolytic 50,000uf R4 | 11-00001-224 Resistor 220K %4W 5% C8 | 12-30001-105 Capacitor, Tantalum 1.uf 35V RS | 11-00001-472 Resistor 4.7K YW 5% R6 | 11-00001-222 Resistor 2.2K YW 5% C9 | 12-20003-209 Capacitor, Electrolytic 20,000uf C10_| 12-10001-332 Capacitor, Ceramic .0033uf R7__| 11-10001-101 Resistor 100 %4W 5% C11 | 12-30001-476 Capacitor, Tantalum 47uf R8__| 11-00001-102 Resistor 10K %W 5% C12 | 12-30001-105 Capacitor, Tantalum 1.ut 35V RQ _| 11-00001-472 Resistor 4.7K YaW 5% C13 | 12-10004-103 Capacitor, Ceramic .01uf Rid | 11-10001-101 Resistor 100 YW 5% C14 | 12-10001-102 Capacitor, .001uf 11-30001-015 11-30001-015 Resistor .15 4W 5% Resistor .15 4W 5% C15 | 12-30001-476 Capacitor, Tantalum 47uf C16 | 12-20002-108 Capacitor, Electrolytic 1,000uf 11-00001-472 Resistor 4.7K Y4W 5% C17 | 12-30001-225 Capacitor, Tantalum 2.2uf 25V 11-00001-222 Resistor 2.2K %4W 5% C18 | 12-30001-225 Capacitor, Tantalum 2.2uf 25V 11-00001-222 Resistor 2.2K %4W 5% C19 | 12-30001-105 Capacitor, Tantalum 1.uf 35V 11-60001-252 Pot 2.5K %4W 20% Fi | 24-00003-010 10A Fuse 11-00001-222 Resistor 2.2K YW 5% F2 | 24-00003-010 10A Fuse 11-60001-102 Pot 1.0K YaW 20% F3__ | 24-00003-003 Fuse, 2A 11-00001-511 | Resistor 510 YW 5% F4 | 24-00003-004 |Fuse, 4A 11-10001-470 | Resistor 47 YW 5% F5 | 24-00003-004 | Fuse, 4A Resistor 1.6K YW 5% BR1 | 13-00100-025 | Diode Bridge 25A, 100V Resistor 10K %W 5% BR2 | 13-00100-012 | Diode Bridge 12A, 100V Resistor 4.7K YW 34 BR3 | 13-00100-002 Diode Bridge 2A, 100V

12-30001-225 Capacitor, Tantalum 2.2uf 25V Resistor 2.2K YW 5% D1 | 13-14002-001 | Diode IN4002 Pot 1.0K 4W 5% D2 | 13-14002-001 | Diode IN4002 11-00001-472 | Resistor 407K YW 5% D3_| 13-10752-001 | Diode, Zener IN752 11-00001-222 | Resistor 2.2K YW 5% D4 | 13-14002-001 | Diode IN4002 11-60001-252 | Pot 2.5K YW 20% D5 | 13-14002-001 | Diode IN4002 11-00001-472 | Resistor 4.7K YW 5% D6 _| 13-14002-001 | Diode IN4002 11-00001-122 | Resistor 1.2K YW 5% D7 _| 13-10964-001 | Diode, Zener IN964 R31_|11-10001-470 | Resistor 47 4W 5% D8 | 13-14002-001 | Diode IN4002

R32_|11-30001-015 | Resistor .15 4W 5%D9 | 13-14002-001 | Diode IN4002
R33_|11-00001-222 | Resistor 2.2K “4W 5%D10 | 13-14002-001 | Diode IN4002
R34_|11-00001-122 | Resistor 1.2K %4W 5%D11 | 13-14002-001 | Diode IN4002

11-00001-511 | Resistor 510 4W 5% D12_ | 13-14002-001 | Diode IN4002 11-00001-222 | Resistor 2.2K 4W 5% LED1} 13-00001-001 | LED (Red) 11-00001-104 | Resistor 100K LED2} 13-00001-001 | LED (Red) 11-00001-103 | Resistor 10K YW 5% LED3} 13-00001-001 | LED (Red) 11-00001-224 | Resistor 220L %4«W 5% LED4} 13-00001-001 | LED (Red) U1 | 15-62500-001 Opto Coupler H11AA2 12-10004-103 Capacitor, Ceramic .O1uf U2_| 15-50556-001 Timer (Dual) 556 12-10004-103 C4 | 12-30001-105 apacitor, Tantalum 1.uf 35V Voltage Regulator 723 U3 | 15-50723-001 tr 15-50723-001 Voltage Regulator 723

at

Page 44

REGULATOR P.C.B.

TAITO SYM | PART NO. DESCRIPTION REG1 | 15-57912-001 Voltage Regulator 7912 REG2 | 15-57905-001 Voltage Regulator 79L05 Q1 | 14-22905-001 | Transistor 2N2905 Q2 | 14-22905-001 | Transistor 2N2905 Q3 | 14-22905-001 | Transistor 2N2905 Q4 | 14-22905-001 | Transistor 2N2905 Q5 | 14-23055-001 | Transistor 2N3055 Q6 | 14-22905-001 | Transistor 2N2905 Q7 | 14-20030-001 | Transistor TIP-30A Q8 | 14-26401-001 | SCR 2N6401 Q9 | 14-26401-001 | SCR 2N6401 J1_ |25-00022-006 | Connector, 1-380999-0 6Pin J2 — |25-00022-008 | Connector, 350212-1 8Pin J3 | 25-00002-014 | Connector, 09-60-1141 14Pin J4 — |25-00002-014 | Connector, 09-60-1140 14Pin 24-10001-001 | Fuse Clips 30-00220-002 | Heat Sink Dual To-220 30-00003-001 | Heat Sink Single To-3 30-00001-001 | Heat sink

Page 45

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 46

VIDEO PROCESSOR

[aay TANTO SYM] PART NO. _ | DESCRIPTION SYM |PARTNO. | DESCRIPTION

C1| 12-10002-104 | Capacitor Ceramic, .1uf,S50V, +80/—20%C55 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%

2 _ | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/-20% | 656 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C3 | 12-19002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C57 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% |

[ca12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%C58 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%

C5 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C59 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—36 C6 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C60 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/--20% | G7 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C61 | 12-30001-106 | Capacitor Tant, 10uf, 16V C8 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C62 | 12-10002-104 | Capacitor Ceramic, .1uf,SOV, +80/—20% CQ | 12-30001-106 | Capacitor Tant, 10uf, 16V C63 | 12-30001-106 | Capacitor Tant, 10uf, 16V C10 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/--20% C64 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C11 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C65 | 12-10001-471 | Capacitor Ceramic, 470uf,50V,10% X7R 12 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% Axial Lead 13 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | C66 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20%

14 | 42-10003-101 | Capacitor Ceramic, 100pf, 10% NPO Axial LeadC67_|12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—20%
Cis | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20%| C68_|#2-10002-104 | Capacitor Ceramic, 1uf,50V. + 80/—20%

Cie | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% Ceg | 12-10002-104 | Capacitor Ceramic, .iuf,50V, +80/—20% C17 | 12-10002-104 | Capacitor Ceramic, .1ut,50V, +80/—20% C70 _| 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20%

ct | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% |C71_|12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20%

Cig | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/-20% C72 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—26% lc20 | 12-10002-104 Capacitor Ceramic, .1uf,50V, +80/—20% C73 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% C21_|12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/— 20% [674 | 12-10002-104 | Capacitor Ceramic, .tuf,S0V, +80/—20% 22 | 12-30001-106 | Capacitor Tant, 10uf, tev C75 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/--20%

€23 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/-20% __|C76_|12-10002-104 | Capacitor Geramic, .1ut,50V, +80/—20%
26 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/- 20%C77_|12-30001-106 | Capacitor Tant, 10uf, 16V

27 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20% C78 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%

28 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%|.¢79_|12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/-20%
€29 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/— 20%£80_|12-30001-106 | Capacitor Tant, 70uf,16V

30 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% | C81 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% €31 | 12-10003-101 | Capacitor Disk 100pf. 10% NPO 82 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20%

32_[12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20%C83 | 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—36

33 | 12-10002-104 | Capacitor Ceramic, .1uf,50V. +80/—20% | 84 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/— 20% 34 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/-20% C85 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 35 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C86 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% €36 | 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/—20% C87 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% | 37 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/— 20% C88 | 12-20001-107 Capacitor Flecrrohc 100ut,25V, as | 12-10902-104 | Gapaction Ceramic, tut, SOV,,+80/—20% 689 | 12-20001-107 | Capacitor Electrolytic, 100ut,25V, C39 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% +100/—20% C40 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20% | C90 | 12-20001-107 | Capacitor Electrolytic, 100uf,25V, C41 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% +100/—20% 42 | 12-10002-104 | Capacitor Tant, 15uf,16V C91 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 43 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/~20% 692 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20% C44 | 12-30001-106 | Capacitor Tant, 10uf, 16V C93 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% C45 | 12-30001-106 | Capacitor Tant, 10uf, 16V C94 | 12-10002-104 | Capacitor Ceramic, .1uf,50V. +80/—20% 50 | 12-10002-104 | Capacitor Ceramic, 1uf,50V, +80/—20% | C95 | 12-10002-104 | Capacitor Ceramic, .tuf,50V, +80/—20%

fest12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20%96 | 12-10001-471 | Capacitor Ceramic, 470pf,50V,10% X7R_ |

52 | 12-10002-104 | Capacitor Ceramic, tuf,50V, +80/ 20% Axial Lead 053 [12-10002-104 | Capacitor Ceramic, uf SOV, +80/—20% G7 | 12 naa taea capac ioy avamle, Op} aOveTtee:AZR C54 | 12-10002-104 | Capacitor Ceramic, “tuf,60V, +80/- 20% 98 | 12-10001-471 | Capacitor Ceramic, 470pf,50V, 10% X7R Axial Lead

Page 47

VIDEO PROCESSOR

TAITO TAITO sym | PART NO. | DESCRIPTION sym | PART NO. _| DESCRIPTION

099 | 12-10002-104 | Capacitor Ceramic, .Tuf,S0V, +80/—20%R37Pt. OHM, AW, 5%
100] 12-10002-104 | Capacitor Ceramic, 1uf,50V, +-80/—20%36_|17-00001-332 | Resistor 3300 ORM, YAW, 5%

C101 12-10003-100 | Capacitor Ceramic, 1Opf. 10% NPO Axial| [R39 | 11-00001-331 | Resistor 330 OHM, HW, 5% bale Ra0_[11-00007-331 [Resistor 380 OHM, YW, 5% 102] 12-10002-104 | Capacitor Ceramic, .1ui,50V, +80/—-20% R41 | 11-00001-331 | Resistor 330 OHM, %W, 5% C103] 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% 71-00001-331 | Resistor 330 OHM, %W, 5% €104| 12-18002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% R43 | 11-00001-331 | Resistor 330 OHM, YW, 5%

C105] 12-10002-104 | Capactor Ceramic, tu Sv, 80-20% |[pag | ¥-0000%-381[Resistor 380 OHNE, iW, 5% ———
C106! 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20%Ras44.00001-471 | Resistor 470 OHM, %4W, 5%

C107} 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/—20% R46 | 11-00001-820 | Resistor 82 OHM, %W, 5%

C108 | 12-10002-104 | Capacitor Ceramic, .1uf,50V, +80/-20%R47 | 11-00001-471 | Resistor 470 OHM, %4W, 5%——

113 Y2-0001-471 | Capacitor Ceramic, OV, 10% 47OPF wae 1 11-00001-181 | Resistor 160 OHM, VW 5%

Aiaoa San | Reaktor 3 OHNE TNT SERag | 17-00001-271 | Resistor 270 OHM, YW, 5%
aa}1-00001-1652 | Resistor 1K. HW. 5xeR50 | 11-00001-473 | Resistor 47K OHM, YAW, 5%
R3_|11-00001-271 | Resistor 270 OHM, YAW. 5%RSTODOT S90 | Resist SS OHMS Ya 32
aaTi-oo0ot=271 | Resistor 270 OM HW 5%m52_|11-00001-330 | Resistor 33 OHM, YAW, 5%
R5_|11-00001-271 | Resistor 270 OHM, YAW, 5%P53 _| 11-00001-850 | Resistor 33° OHM, YAW. 5%

6 _| 11-00001-332 | Resistor 3.3K, YAW, 5% ce

R7_ | 11-00001-221 | Resistor 220 OHM, YAW, 5%R55_|11-00001-330 | Resistor 33 OHM, YW, 5%
aa 1 7100007-222 | Resistor 2.2K, GW. 3656_|17-00001-330 | Resistor 33 OHM, YAW, 5%
so11-00001-330 | Resetor 33 OM, Tw.RS7_|17-00001-330 | Resistor 33 OHM, YAW, 5%
wid | 11-00007-330 | Resistor 3 OHM” RW 5%R5B_|11-00001-230 | Resistor 33 OHM, ‘AW, 5%

R11 | 11-00001-390 | Resistor 33 OHM, Y4W, 5% Be | Too Tess PResisir SK OHM Wl. 2k

R12 | 11-00001-330 | Resistor 33 OHM, “AW, 5%R60]11-00001-382 | lesistor. $300 OHM, AW, 5%
R13 | 17-00001-820 | Resistor 82 OHM, YAW, 5%ETLOUTSResistor Se Wat

4 | 11-00001-181 | Resistor 180 OHM, YaW, 5% iL

Rts | 11-00001-271 | Resistor 270 OHM, YW, 5%Gd | 71-go00i-102[Resistor 1K, “AW, 5%=]

R16 | 11-00001-471 | Resistor 470 OHM, 1aWl, 5% R64 | 11-Q0001%124 | iesetor 120, CHM, SANs SY

Ri7_|11-00001-471 | Resistor 470 OHM. %W, 5%aEE
{Rie | 11-00001-271 | Resistor 270 OHM, YAW, 5%R66_|11-00001-392 | Resistor 3.34, WW, 5%—

Rig | 11-00001-181 | Resistor 180 OHM, Yaw, 5% R67 _} 11-00001-332 | Resistor 3300 OHM, %W, 5%

R20 | 11-00001-820 | Resistor 82 OHM, YAW, 5%|i11-00001-982 | Resistor 3.9K, WW, 5%

R2i_|11-00001-330 | Resistor 33 OHM, %4W, 5% R69 | 11-00001-332 | Resistor 3.3K, MW, 5%

R22_|11-00001-330 | Resistor 33 OHM, YAW, 5%FB1_|17-00001-001 | Ferrite Bead
[R23_| 11-00001-330 | Resistor 33 OHM, YAW, 5%62:{'17-Do001-001 | Femite Beat
R24 | 11-00001-330 | Resistor 33 OHM, YAW, 5%FB3_|17-00001-001 | Ferrite Bead

R25 | 11-00001-380 | Resistor 33 OHM, ‘AW, 5% FEA | 17-00001-00 | Ferrite Bead [R26 | 11-00001-390 | Resistor 33 OHM, AW, 5% 85 | 17-00001-001 | Ferrite Bead

R27_|11-00001-330 | Resistor 33 OHM, YAW, 5%Fed17-00001-001 | rernite Bead
R28_|11-00001-181 | Resistor 180 OHM, %W, 5%FB7_{17-00001-001 | Ferrite Bead——|

R29 | 11-0000%-471 | Resistor 470 OHM, AW, 5% F8_|17-00001-001 | Fert Bead

R30_|11-00001-471 | Resistor 470 OHM, YAW, 5%FBS. | 17-00001-001 re Bead
R3i_|11-00001-471 | Resistor 470 OHM, AW, 5%|FB10 | 17700001001"Ferrite Bead

R32_[11-00001-471 | Resistor 470 OHM, YAW, 5% F149 17:000010001| Ferme Bend

R33_|11-00001-471 | Resistor 470 OHM, YW, 5%Qi14-23904-001 | Transistor NPN Silicon (2N3904)
faa’11-00007-681 T Resistor 680 OHM. Taw 5%a2 _| 14-23904-007 | Transistor NPN Silicon (2N3904)
R35 | 11-00001-391 | Resistor 390 OHM, YAW, 5%Q3__|14-23904-001 | Transistor NPN Silicon (2N3904)
R36 | 1¥-00001-330 | Resistor 33 OHM, %W, 5%|Q4 | 14-23904-001 | Transistor NPN Silicon (2N3904)
Page 48

TAITO TAITO

‘SYM | PART NO.DESCRIPTIONSYM | PART NO.DESCRIPTION

Q5 | 14-23904-001 | Transistor NPN Silicon (2N3904) U11 |15-10001-001 | RAM 16K x 1 Dynamic (4116) Q6 | 14-23904-001 | Transistor NPN Silicon (2N3904) 26-00001-016 | Socket DIP 16 Pin for U11 Q7 = | 14-23904-001 | Transistor NPN Silicon (2N3904) U2 [15-10001-001 [RAM 16K x 1 Dynamic (4116)

Q8 | 14-23905-001[Transistor NPN Silicon (2N3905)}26-00001-016 | Socket DIP 16 Pin for U12
LED1 |13-00001-001|L.E.D. RED, TL-1%U13 [15-10001-001 | RAM 16K x 1 Dynamic (4116)
LED2 | 13-00001-001|L.E.D. RED, TL-1%26-00001-016 | Socket DIP 16 Pin for U13
LED3 |13-00001-001|L.E.D. RED, TL-1%U14 [15-10001-001 | RAM 16K x 1 Dynamic (4116)
LED4 |13-00001-001|L.£.D. RED, TL-1%26-00001-016 | Socket DIP 16 Pin for U14
LEDS [13-00001-001[L.E.D. RED, TL-1%U15 [15-10001-001 | RAM 16K x 1 Dynamic (4116)
LED6 |13-00001-001|L.E.D. RED, TL-1%|26-00001-016 | Socket DIP 16 Pin for U15
Y1 — |19-00003-001|CRYSTAL, 20,000MHZU16 |15-10001-001 | RAM 16K x 1 Dynamic (4116)

BATT |20-00001-001 | Battery, NICAD, 3.6V, 1/3 AA 26-00001-016 | Socket DIP 16 Pin for U16

SW1|29-00017-001 | Switch MomentaryU17 |15-10001-001 | RAM 16K x 1 Dynamic (4116)
TP1|59-00021-001 | Test Point26-00001-016 | Socket DIP 16 Pin for U17
TP2|59-00021-001 |Test PointU18 | 15-00003-001 | CRT CONTROLLER 68A45
TP3|59-00021-001 | Test Point26-00001-040 | Socket DIP 40 Pin for U18
TP4|59-00021-001|Test PointU19 | 15-20086-001 | Quad 2 Input Exclusive or (74LS86)
TP5}59-00021-001 | Test PointU20 |15-20086-001 | Quad 2 Input Exclusive or (74LS86)
TP6|59-00021-001 | Test Point[oz 15-20157-001 | Multiplexer Quad 2-Input (74LS157)
TP7|59-00021-001 |Test PointU22 }15-20032-001 | Quad 2 (nput or (74LS157)
TP8|59-00021-001|Test PointU23 |15-20161-001 | Counter, 4 Bit Presetable (74LS161)
RP1|11-50001-102|1K OHM Resistor Sip PackU24 |15-20004-001 | Inverter, HEX (74LS04)

RP2 | 11-50001-473 |47K OHM Resistor Sip Pack U25 |15-70374-001 | Latch, Octal Shockey (74LS374) [RP3_[11-50001-332 [3.3K Resistor Sip Pack U26 |15-10001-001 | RAM 16K x1 Dynamic (4116)

RP4|11-50001-332 |3.3K Resistor Sip Pack26-00001-016 | Socket DIP 16 Pin for U26

RP5_|11-50001-332 {3.3K Resistor Sip Pack U27 |15-10001-001 | RAM 16K x1 Dynamic (4116)

Ji{25-00001-014 | Connector, 14 Pin .156 Center26-00001-016 | Socket DIP 16 Pin for U27

|s2 _ [25-00002-014 Connector, 14 Pin .156 Center U28 |15-10001-001 | RAM 16K x1 Dynamic (4116)

J3|25-00001-001 | Connector, 50 Pin Header Vertical26-00001-016 | Socket DIP 16 Pin for U28

J6 — |25-00001-001 | Connector, 50 Pin Header Vertical U29 |15-10001-001 | RAM 16K x1 Dynamic (4116)

J19_|25-00002-002 | Connector, 2 Pin .156 Center26-00001-016 | Socket DIP 16 Pin for U29
W1_[25-00021-002 [Connector .1 Center for W1U30 | 15-10001-001 | RAM 16K x1 Dynamic (4116)
[wi26-00007-001 | Shorting Pin26-00001-016 | Socket DIP 16 Pin for U30
132-00001-001|P.C.B. Video Processor BoardU31 |15-10001-001 | RAM 16K x1 Dynamic (4116)
U1|15-20245-001|Bus Transiciever, Octal (74LS245)26-00001-016 | Socket DIP 16 Pin for U31
U2|15-20245-001|Bus Transiciever, Octal (74LS245)U32 | 15-10001-001 | RAM 16K x1 Dynamic (4116)
U3|15-10003-001|Ram 1K x 4 NMOS Static (2114)26-00001-016 | Socket DIP 16 Pin for U32

126-00001-018 | Socket DIP 18 Pin for U3 U33 | 15-10001-001 | RAM 16K x1 Dynamic (4116)

U4_}15-10003-001|Ram 1K x 4 NMOS Static (2114)26-00001-016 | Socket DIP 16 Pin for U33

126-00001-018 |Socket DIP 18 Pin for U4 U34 | 15-20374-001 | Latch, Octal (74LS374) '15-20157-001 | Multiplexer Quad 2-Input (74LS157) U35 {15-20153-001 | Multiplexer, Dual 4-Input (74LS153) 15-20157-001 | Multiplexer Quad 2-Input (74LS157) U36 | 15-20074-001 | Flip Flop Dual-D (74LS74)

15-20074-001|Flip Flop, Dual D (74LS74)U37 | 15-20008-001 | Quad, 2-Input and (74LS08)

'15-20032-001 [ouad 2 Input or (74LS32) U38 | 15-70113-001 | Flip Flop JK Schottky (74LS113) 15-20032-001 | Quad 2 Input or (74LS32) U39 | 15-20004-001 | Inverter, HEX (74LS04) {15-10001-001_|RAM 16K x 1 Dynamic (4116) U40 | 15-30017-001 | Buffer/Driver, HEX (7417) 26-00001-016 |Socket DIP 16 Pin for U10 U41 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) 26-00001-016 | Socket DIP 16 Pin for U41

Page 49

TAITO TAITO PART NO. DESCRIPTION ‘SYM |PART NO. DESCRIPTION 15-10001-001 | RAM 16K x 1 Dynamic (4116) 15-20157-001 | Multiplexer Quad 2-Input (74LS157) 26-00001-016 | Socket DIP 16 Pin for U42 15-00002-001 | Microprocessor 68A09E 15-10001-001 | RAM 16K x 1 Dynamic (4116) 126-00001-040 | Socket DIP 40 Pin for U82 26-00001-016 | Socket DIP 16 Pin for U43 15-10001-001 | RAM 16K x 1 Dynamic (4116) 15-20244-001 ‘octal, Buffer (74LS244) 15-20244-001 Octal, Buffer (74LS244) 26-00001-016 | Socket DIP 16 Pin for U44 1 5-10002-001 RAM 1K x 4 CMOS Static (6514) 15-10001-001 | RAM 16K x 1 Dynamic (4116) 26-00001-016 | Socket DIP 16 Pin for U45 126-00001-018 | Socket DIP 18 Pin for U85 15-10002-001 | RAM 1K x 4 CMOS Static (6514) oS 15-10001-001 | RAM 16K x 1 Dynamic (4116) J26-00001-018 Socket DIP 18 Pin for U86 26-00001-016 | Socket DIP 16 Pin for U46 '15-20139-001 Decoder Dual 1 of 4 (74LS139) 15-10001-001 | RAM 16K x 1 Dynamic (4116) j15-20032-001 Quad 2-Input of (74LS32) 26-00001-016 | Socket DIP 16 Pin for U47 '15-20074-001 Flip Flop, Dual-D (74LS74) 15-10001-001 | RAM 16K x 1 Dynamic (4116) {is2m00eon Inverter, HEX (74LS04) 26-00001-016 | Socket DIP 16 Pin for U48 '15-20374-001 Latch, Octal (74LS374) 15-20032-001 | Quad 2-Input or (74LS32) 15-20374-001 Latch, Octal (74LS374) ugg |15-20374-001 Latch, Octal (74LS374) | 18-20086-009 Quad 2-input Exclusive or (74.S86) 15-20086-001 | Quad 2-Input Exclusive or (74LS86) 15-20374-001 Latch, Octal (74L5374) 15-20153-001 | Multiplexer, Dual 4-Input (74LS153) 15-20299-001 Shift Register 8 Bit (74LS299) 15-20153-001 | Multiplexer, Dual 4-Input (741S153) 96 [15-20299-001 Shift Register 8 Bit (741299) 54 |15-20153-001 Multiplexer, Dual 4-Input (74LS153) 15-20244-001 Buffer, Octal (74LS244) a 15-20167-001 | Multiplexer, Quad 2-Input (74LS157) 15-20244-001 Buffer, Octal (74.8244) 15-10008-001 | RAM 1K x 4 HMOS Static (2148) 15-20138-001 Decoder, 1 of 8 (74LS138) 26-00001-018 | Socket DIP 18 Pin for U56 15-40000-001 Quad 2-Input NOR (74C00) 15-10008-001 | RAM 1K x 4 HMOS Static (2148) 15-20008-001 | Quad 2-Input AND (74LS08) 26-00001-018 | Socket DIP 18 Pin for U57 U102}15-20010-001 | Tripie 3-Input AND (74LS10) 15-30017-001 | Bufter/Driver, HEX (7417) U103}15-20000-001 | Quad 2-Input NAND (74LS00) 15-10001-001 | RAM 16K x 1 Dynamic (4116) U104115-20187-007 [Multiplexer Quad 2-Input (74LS157) U60 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U105|15-20299-001 Shift Register 8 Bit (74LS299) U61 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U106]15-20299-001 Shift Register 8 Bit (74LS299) U62 | 15-10001-001 | RAM 16K x 1 Dynamic (4116) U107/15-20299-001 Shift Register 8 Bit (74LS299) U108}15-20299-001 Shift Register 8 Bit (74LS299) 15-10001-001 | RAM 16K x 1 Dynamic (4116) U109}15-20299-001 Shift Register 8 Bit (74LS299) U63 | 15-10001-001 [fa 16K x 1 Dynamic (4116) [15-10007-001 RAM 16K x 1 Dynamic (4116) U110}15-20299-001 Shift Register 8 Bit (74LS299) 15-10001-001 | RAM 16K x 1 Dynamic (4116) 15-20032-001 | Quad 2-Input or (741532) 15-20244-001 | Octal Buffer (74LS244) 15-20245-001 | BUS Transciever, Octal (74LS245) 15-20374-001 | Latch, Octal (74LS374) 15-20374-001 | Latch, Octal (74LS374) 15-20374-001 | Latch, Octal (741S374) 15-20157-001 | Multiplexer Quad 2-Input (74LS157) 15-20157-001 | Multiplexer Quad 2-Input (74LS157)

15-20273-001 | Register 8 Bit (7415273) 15-20245-001 | BUS Transciever, Octal (74LS245)

15-20373-001 | Latch, Octal (74LS373) 15-20373-001 | Latch, Octal (74LS373) 15-20373-001 | Latch, Octal (7418373) 15-20373-001 | Latch, Octal (74LS373)

al

Page 50

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 51

DATA/SOUND PROCESSOR

TAITO TAITO SYM | PART NO. DESCRIPTION PART NO. DESCRIPTION

R1__|11-00001-473 | Resistor 47K %4W +5%17-00001-001 | Ferrite Bead
R2__|11-00001-332 | Resistor 3.3K ¥4W +5%17-00001-001 | Ferrite Bead
R3_|11-00001-332 | Resistor 3.3K %4W +5%17-00001-001 | Ferrite Bead
R4__|11-00001-332 | Resistor 3300 OHM %4W +5%17-00001-001 | Ferrite Bead

R5 | 11-00001-472 | Resistor 4.7K %W +5% 17-00001-001 | Ferrite Bead

R6__|11-00001-103 | Resistor 4.7K ¥4W +5%17-00001-001 | Ferrite Bead

R7 | 11-00001-103 | Resistor 10K %4W +5% 17-00001-001 | Ferrite Bead R8 | 11-00001-332 | Resistor 3.3K OHM %4W +5% 17-00001-001 | Ferrite Bead RQ | 11-60001-502 | Pot, P.C. Mount 5K 17-00001-001 | Ferrite Bead R10 | 11-00001-473 | Resistor 47K %4W +5% 17-00001-001 | Ferrite Bead R11 | 11-00001-473 | Resistor 47K YW +5% 17-00001-001 | Ferrite Bead R12 | 11-00001-332 | Resistor 3.3K %W +5% 17-00001-001 | Ferrite Bead

R13_|11-00001-332 | Resistor 3.3K %4W +5%17-00001-001 | Ferrite Bead
[ava11-00001-332 | Resistor 3.3K “W +5%12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead

R15 | 11-00001-332 | Resistor 3.3K %4W +5% 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R16 | 11-00001-332 | Resistor 3.3K %4W +5% 12-10002-104 | Capacitcr Ceramic .1uf 50V Axial Lead R17_ | 11-00001-332 | Resistor 3300 OHM YW +5% 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R18 | 11-00001-124 | Resistor 120K %4W +5% 12-10002-104 | Capacitor Ceramic .tuf 50V Axial Lead R19 | 11-00001-472 | Resistor 4.7K %W +5% 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead R20 | 11-00001-221 | Resistor 220 OHM %W +5% 12-20001-107 | Capacitor Electrolytic 100uf 16V R21_ | 11-00001-221 | Resistor 220 OHM %4W +5% 12-20001-107 | Capacitor Electrolytic 100uf 16V R22 | 11-00001-332 | Resistor 3.3K %4W +5% 12-20001-107 | Capacitor Electrolytic 100uf 16V 11-00001-182 | Resistor 1.8K %4W +5% 12-20001-107 | Capacitor Electrolytic 100uf 16V 11-60001-104 | POT, P.C. Mount 100K C11 | 12-20001-107 | Capacitor Electrolytic 100uf 16V 11-00001-103 | Resistor 10K %4W +5% C12 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 11-00001-103 | Resistor 10K %4W +5% C13 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 11-00001-223 | Resistor 22K YW +5% C14 | 12-10002-104 { Capacitor Ceramic .1uf 50V Axial Lead 11-00001-562 | Resistor 5.6K %4W +5% C15 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 11-00001-332 | Resistor 3.3K YW +5% C16 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 11-00001-020 | Resistor 2.2 OHM %W +5% C17 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 11-00001-010 | Resistor 1 OHM %2W +5% C18 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead 11-00001-020 | Resistor 2.2 OHM %4W +5% C19 | 12-10003-470 | Capacitor 47pf 10% NPO Axial Lead 11-00001-010 | Resistor 1 OHM %W +5% C20 | 12-20001-105 | Capacitor Electrolytic 1uf 11-00001-102 | Resistor 1.0K OHM %W +5% C21_ | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 11-00001-332 | Resistor 3.3K %4W +5% C22 | 12-20001-807 | Capacitor Electrolytic 800uf, 16V 11-00001-152 | Resistor 1.5K ¥4W +5% C23 | 12-20001-807 | Capacitor Electrolytic 800uf, 16V

11-00001-222 | Resistor 2.2K 4W +5%C24_|12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead

11-00001-221 | Resistor 220 OHM %W +5% C25 _| 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead 11-00001-332 | Resistor 3.3K %4W +5% C26 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead 11-00001-562 | Resistor 5.6K 4W +5% €27 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead 11-00001-223 | Resistor 22K Y4W +5% €28 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead 11-00001-103 | Resistor 10K %4W +5% C30 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead 11-00001-103 | Resistor 10K %4W +5% C31 | 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead

11-00001-103 | Resistor 10K YW +5%C32_|12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead

11-00001-472 | Resistor 4.7K %4W +5% 33. | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 17-00001-001 | Ferrite Bead C34 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 17-00001-001 | Ferrite Bead C35 | 12-10002-104 | Capacitor Ceramic .tuf 50V Axial Lead 17-00001-001 | Ferrite Bead C36 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 17-00001-001 | Ferrite Bead

Page 52

DATA/SOUND PROCESSOR

TAITO TAITO [oes

SYM | PART NO.DESCRIPTIONSYM|PARTNO. — | DESCRIPTION

12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead TP3_ | 59-00021-001 | Test Point 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead TP4 | 59-00021-001 | Test Point 12-10001-123 | Capacitor Ceramic .012 50V Axial Lead TPS | 59-00021-001 | Test Point 12-10001-183 | Capacitor Ceramic .018 50V Axial Lead TP6 } 59-00021-001 } Test Point 12-10004-103 | Capacitor Ceramic .01uf 50V Axial Lead TP7 | 59-00021-001 | Test Point C42 | 12-10001-332 | Capacitor Ceramic .0033uf 50V Axial Lead TP8 | 59-00021-001 | Test Point

C43 | 12-10001-153 | Capacitor Ceramic .015uf 50V Axial LeadTP9 | 59-00021-001 | Test Point|
caa_| 12-1001 863Capacitor Ceramic .056uf SOV Axia! LeadTP10 | 59-00021-001 | Test Point

C45 | 12-10003-100 | Capacitor 10pf NPO Axial Lead f P11 | 59-00021-061 | Test Point C46 | 12-10002-104 } Capacitor Ceramic .1uf 50V Axial Lead RP1 | 11-50001-332 | Resistor Sip Pack 3.3K

oat _{asCapacitor Electrolytic 1uf Axial LeadRP2 | 11-50001-332 | Resistor Sip Pack 3.3K

C48 | 12-20001-105 } Capacitor Electrolytic 1uf Axial Lead RP3 | 11-50001-471 | Resistor Sip Pack 47K C49 | 12-10001-471 | Capacitor Ceramic 470uf 50V Axial Lead RP4 | 11-50001-471 | Resistor Sip Pack 47K C50 | 12-10001-471 | Capacitor Ceramic 470pf SOV Axial Lead RP5 | 11-50001-103 | Resistor Sip Pack 10K C51 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead RP6 | 11-50001-332 | Resistor Sip Pack 3.3K 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead U1 | 15-20244-001 | Octal Buffer (74LS244) 12-10002-104 | Capacitor Ceramic .tuf SOV Axial Lead U2 | 15-00002-001 | Microprocessor 68AQ9E C54 | 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead al 26-00001-040 | Socket 40P DIP-For 68AQ9E

[ss12-20001-105 | Capacitor Electrolytic 1ufU3__|15-20244-001 | Octal Buffer (7415244)
C56 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axiai LeadU4 | 15-20244-001 | Octal Buffer (74LS244).|

C57 | 12-20001-477 { Capacitor Electrolytic 470uf, 16V U5 | 15-00007-001 | Microprocessor 6802 C58 | 12-20001-477 | Capacitor Electrolytic 470uf, 16V 26-00001-040 | Socket 49P DIP for 6802

Cc12-10002-104 | Capacitor Ceramic .1uf 50V Axial LeadU6 | 15-20244-001 | Octal Buffer (74LS244)
C60 | 12-10002-104 | Capacitor Ceramic .1uf SOV Axial LeadU7 __} 15-00004-002 | Parallel 1/0 68217

C61 | 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead U8 | 15-00004-002 | Parallel 1/0 6821 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead U9 | 15-20245-001 | BUS Tranciever, Octal (74LS245) 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U10 | 15-20244-001 | Octal Buffer (74LS244)

12-10001-471 | Capacitor Ceramic 470pt 50V 10% Axial LeadU11_{15-20245-001 | BUS Tranciever, Octal (74LS245)

12-10001-471 | Capacitor Ceramic 470pt 50V 10% Axial Lead U12_ | 15-20244-001 | Octal Buffer (741244) 12-10001-471 | Capacitor Ceramic 470pf SOV 10% Axial Lead U13_ | 15-50001-001 | Digital to Analog Converter 8 Bit (1408) 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U14 | 15-20032-001 | Quad 2-Input or (74LS32) 12-10002-104 | Capacitor Ceramic .tuf SOV Axial Lead U15 | 15-10003-001 | RAM 1K x 4 NMOS Static (2114) 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead 26-00001-018 | Socket 18P DIP for 2114 12-10002-104 | Capacitor Ceramic .1uf SOV Axial Lead U16 | 15-10003-001 | RAM 1K x 4 NMOS Static (2114) 12-10002-104 } Capacitor Ceramic .1uf 50V Axial Lead 26-00001-018 | Socket 18P DIP for 2114

12-10003-101 | Capacitor 100pf 10% NPO Axial LeadU17_|15-20138-001 | Decoder 1 of 8 (7415138)

12-10003-221 | Capacitor 220pf 10% NPO Axial Lead U18 | 15-50003-007 | Quad OP AMP LM324 12-10002-104 | Capacitor Ceramic . 1uf 50V Axial Lead U19 | 15-60004-001 | Speech Synthesis TMS5200 12-20001-105 | Capacitor Electrolytic tut 26-00001-028 | Socket 28P DIP for TMS5200 12-20001-105 | Capacitor Electrolytic tut U20 | 15-09004-001 | Parallel 1/0 68A21 12-10002-104 | Capacitor Ceramic .1uf 50V Axial Lead U21_ | 15-60002-001 | Line Driver (MC1488) 12-10002-104 | Capacitor Ceramic .tuf 50V Axial Lead U22 | 15-00005-002 | Serial /0 68A50

12-10002-104 | Capacitor Ceramic . 1uf 50V Axial Lead26-00001-024 | Socket 24P DIP for 68A50‘|

12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U23_ | 15-20004-001 | Inverter, HEX (74LS04) 12-10001-471 | Capacitor Ceramic 470pf 50V 10% Axial Lead U24 | 15-44066-001 | Quad Analog Multiplexer (4066) 12-10003-100 | Capacitor 10pf NPO Axial Lead U25 | 15-60001-001 | Line Receiver (MC 1489)

§9-00021-001 | Test PointU26_|15-20161-001 | Counter 4-Bit Presettable (7415161)

TP2_{59-00021-001 | Test Point U27 | 15-20092-001 | Counter Divide By Twelve (74LS92) U28 | 15-44066-001 | Quad Analog Multiplexer (4066)

Page 53

DATA/SOUND PROCESSOR

TAITO PART NO. DESCRIPTION 15-50002-001 Audio Amplifier (2002) 30-00001-001 Heatsink to 220

15-50002-001 Audio Amplifier (2002) 30-00001-001 Heatsink to 220

29-00001-001 Switch, DIP 4 Pole 19-00002-001 Crystal 7.3728 MHZ 14-23904-001 Transistor NPN, Silcon 2N3904 25-00002-004 Connector 14 PIN Locking 25-00001-001 Connector Header 50 PIN 25-00001-001 Connector Header 50 PIN 25-00002-005 Connector 5 PIN Locking 25-00002-005 Connector 5 PIN Locking 25-00003-001 Connector RS232

Page 54

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 55

ROM//0 P.C. ASSEMBLY

TAITO TAITO

SYM | PART NO.DESCRIPTIONSYM} PART NO.DESCRIPTION
R1 | 11-00001-562 | Resistor 5.6K, 4W +5%R51 | 11-00001-471|Resistor 470 CHM %W +5%

R2 | 11-00001-471 | Resistor 470 OHM %W +5% R52 | 11-00001-562 | Resistor 5.6K, %4W +5%

R3__|11-00001-471 | Resistor 470 OHM YW +5%R53 | 11-00001-562 | Resistor 5.6K, %4W +5%

R4 | 11-00001-471 | Resistor 470 OHM %4W +5% R54 | 11-00001-471 | Resistor 470 OHM %W +5% RS | 11-00001-471 | Resistor 470 OHM %4W +5% R55 | 11-00001-471 | Resistor 470 OHM YW +5% R6 | 11-00001-471 | Resistor 470 OHM YW +5% R56 | 11-00001-471 | Resistor 470 OHM %4W =5%

R7__|11-00001-471 | Resistor 470 OHM %W +5%R57 | 11-00001-471 | Resistor 470 OHM %4W +5%
R8__|11-00001-471 | Resistor 470 OHM YW +5%R58 | 11-00001-471 | Resistor 470 OHM %4W +5%

RQ | 11-00001-471 | Resistor 470 OHM YW +5% R59 | 11-00001-471 | Resistor 470 OHM %4W +5%

R10 | 11-00001-471 | Resistor 470 OHM YW =5%R6O | 11-00001-471|Resistor 470 OHM Y%4W +5%
R11 | 11-00001-471 | Resistor 470 OHM YW +5%R61 | 11-00001-471|Resistor 470 OHM %W +5%

R12 | 11-00001-471 | Resistor 470 OHM %W +5% R62 | 11-00001-471 | Resistor 470 OHM %W +5% R13 | 11-00001-471 | Resistor 470 OHM Y4W +5% R63 | 11-00001-471 | Resistor 470 OHM %W +5% R14 | 11-00001-471 | Resistor 470 OHM %W +5% C1 | 12-10002-104 \Capacitor Ceramic .1uf Axial Lead R15 | 11-00001-471 | Resistor 470 OHM %W +5% C2 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R16 | 11-00001-471 | Resistor 470 OHM %W +5% C3 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead

R17_|11-00001-471 | Resistor 470 OHM YW +5%C4 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
R18 | 11-00001-471 | Resistor 470 OHM YW +5%C5 | 12-10001-471|Capacitor Ceramic 470pf Axial Lead
R19 | 11-00001-471 | Resistor 470 OHM %4W +5%C6 | 12-10001-471|Capacitor Ceramic 470pf Axial Lead

R20 | 11-00001-562 | Resistor 5.6K, %4W +5% C7 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R21 | 11-00001-562 | Resistor 5.6K, %4W +5% C8 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R22 | 11-00001-562 | Resistor 5.6K, 4W +5% C9 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R23 | 11-00001-562 | Resistor 5.6K, %W +5% C10 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R24 | 11-00001-562 | Resistor 5.6K, %4W +5% C11 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R25 | 11-00001-562 | Resistor 5.6K, ¥4W +5% C12 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R26 | 11-00001-562 | Resistor 5.6K, Y4W +5% C13 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead

R27 | 11-00001-562 | Resistor 5.6K, %W +5%C15 | 12-10001-471|Capacitor Ceramic 470pf Axial Lead

R28 | 11-00001-471 | Resistor 470 OHM YW +5% C16 | 12-10001-471 | Rapacitor Ceramic 470pf Axial Lead R29 | 11-00001-471 | Resistor 470 OHM %W +5% C17 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R30_ | 11-00001-471 | Resistor 470 OHM %4W +5% C18 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R31_ | 11-00001-471 | Resistor 470 OHM %4W +5% C19 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead

R32_|11-00001-471 | Resistor 470 OHM %4W +5%C20 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead
R33_|11-00001-471 | Resistor 470 OHM YW +5%C21_|12-10001-471 | Capacitor Ceramic 470pf Axial Lead
R34_|11-00001-471 | Resistor 470 OHM %&W +5%C22 | 12-10001-471Capacitor Ceramic 470pf Axial Lead

R35 | 11-00001-471 | Resistor 470 OHM %W +5% C23 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R36 | 11-00001-471 | Resistor 470 OHM %“W +5% C24 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R37_ | 11-00001-471 | Resistor 470 OHM %4W +5% C25 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R38 | 11-00001-471 |Resistor 470 OHM %W +5% C26 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R39 | 11-00001-471 | Resistor 470 OHM %W +5% C27 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R40 | 11-00001-562 | Resistor 5.6K, YW +5% C28 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R41 | 11-00001-562 | Resistor 5.6K, %W +5% C29 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R42 | 11-00001-562 | Resistor 5.6K, %4W +5% C30 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R43 | 11-00001-562 | Resistor 5.6K, ¥4W +5% C31 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead

R44 | 11-00001-471 | Resistor 470 OHM YW +5%€32_|12-10002-104 | Capacitor Ceramic .1uf Axial Lead
R45_|11-00001-471 | Resistor 470 OHM %W +5%€33_|12-10002-104 | Capacitor Ceramic .1ut Axial Lead

R46 | 11-00001-471 | Resistor 470 OHM %4W +5% C34 } 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R47 | 11-00001-471 | Resistor 470 OHM %4W +5% C35 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead R49 | 11-00001-471 | Resistor 470 OHM %“W +5% C36 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead R50 | 11-00001-471 | Resistor 470 OHM YW +5%

Page 56

ROM/I/0 P.C. ASSEMBLY

TAITO TAITO

SYM | PART NO.DESCRIPTIONSYM | PART NO.DESCRIPTION
C37 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadC85|12-10001-471|Capacitor Ceramic 470pf Axial Lead
C38 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadC86 | 12-10001-471|Capacitor Ceramic 470pf Axial Lead
C39 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadC87|12-10001-471 | Capacitor Ceramic 470pf Axial Lead

C40 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C88 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead

C41 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadC89|12-10001-471 | Capacitor Ceramic 470pf Axial Lead

C42 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead C90 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead

C43 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadC91|12-10001-471 | Capacitor Ceramic 470pf Axial Lead
C44 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadC92|12-10001-471|Capacitor Ceramic 470pf Axial Lead
C45 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadFB1 | 17-00001-001|Ferrite Bead
C46 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead|FB2|17-09001-001 | Ferrite Bead

C47 | 12-10001-471 | Capacitor Ceramic 470pf Axia! Lead FB3_ | 17-00001-001 | Ferrite Bead

C48 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadFB4|17-00001-001 | Ferrite Bead
C49 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadFBS | 17-00001-001|Ferrite Bead
C50 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadFB6 | 17-00001-001|Ferrite Bead
C51 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadFB7 | 17-00001-001|Ferrite Bead
C52 | 12-10002-104 | Capacitor Ceramic .1uf Axial LeadFB8 | 17-00001-001|Ferrite Bead
C53 | 12-10002-104 | Capacitor Ceramic .1uf Axial LeadFB9 | 17-00001-001|Ferrite Bead
C54 | 12-10002-104 | Capacitor Ceramic .1uf Axial LeadFB10 | 17-00001-001|Ferrite Bead
C55 | 12-10002-104 | Capacitor Ceramic .1uf Axial LeadFB11 | 17-00001-001|Ferrite Bead

€56 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB12 | 17-00001-001 | Ferrite Bead

C57 | 12-10002-104 | Capacitor Ceramic .1uf Axial LeadFB13 | 17-00001-001|Ferrite Bead

C58 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB14 | 17-00001-001 | Ferrite Bead C59 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB15 | 17-00001-001 | Ferrite Bead

C60 | 12-10002-104 | Capacitor Ceramic .1uf Axial LeadFB16 | 17-00001-001|Ferrite Bead
C61 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadFB17 | 17-00001-001|Ferrite Bead

C62 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB18 | 17-00001-001 | Ferrite Bead C63 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB19 | 17-00001-001 | Ferrite Bead C64 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB20 | 17-00001-001 | Ferrite Bead | Ges | 12-10001-471 Capacitor Ceramic 470pf Axial Lead | FB21 | 17-00001-001 | Ferrite Bead C66 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB23 | 17-00001-001 | Ferrite Bead C67 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB24 | 17-00001-001 | Ferrite Bead C68 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB25 | 17-00001-001 | Ferrite Bead [c69 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB26 | 17-00001-001 | Ferrite Bead C70 | 12-20001-107 | Capacitor Electrolytic 100uf FB27 | 17-00001-001 | Ferrite Bead C71 | 12-10001-471 | Capicitor Ceramic 470pf Axial Lead FB28 | 17-00001-001 | Ferrite Bead C72 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB29 | 17-00001-001 | Ferrite Bead C73 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB30 | 17-00001-001 | Ferrite Bead C74 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB31 | 17-00001-001 | Ferrite Bead C75 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB32 | 17-00001-001 | Ferrite Bead C76 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB33 | 17-00001-001 | Ferrite Bead C77 | 12-10002-104 | Capacitor Ceramic .1uf Axial Lead FB34 | 17-00001-001 | Ferrite Bead

C78 | 12-10001-471 | Capacitor Ceramic 470pf Axial LeadFB35 | 17-00001-001|Ferrite Bead

C79 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB36 | 17-00001-001 | Ferrite Bead C80 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB37 | 17-00001-001 | Ferrite Bead C81 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB38 | 17-00001-001 | Ferrite Bead C82_| 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB39 | 17-00001-001 | Ferrite Bead C83 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB40 | 17-00001-001 | Ferrite Bead C84 | 12-10001-471 | Capacitor Ceramic 470pf Axial Lead FB41 | 17-00001-001 | Ferrite Bead

Page 57

ROM/V/0 P.C. ASSEMBLY

TAITOFTAITO
SYM | PART NO.DESCRIPTIONSYM | PART NO.DESCRIPTION
FB42 |17-00001-001 | Ferrite BeadU6E-PROM ‘SPACE DUNGEON'™

FB43 | 17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U6

FB44 |17-00001-001 | Fertite BeadU7E-PROM “SPACE DUNGEON'™

FB45 |17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U7

FB46 |17-00001-001 | Ferrite BeadU8E-PROM “SPACE DUNGEON’’™

FB47 |17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U8

FB48 |17-00001-001 | Ferrite BeadugE-PROM “SPACE DUNGEON”™

FB49 |17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U9

FB50 |17-00001-001 | Ferrite BeadU10E-PROM “SPACE DUNGEON'’’™

FB51 |17-00001-001 | Ferrite Bead 26-00001-024 | Socket 24 Pin Dip for U10 FB52 | 17-00001-001 | Ferrite Bead U11 | 15-00004-001 | Paralell 1/0 68A21

FB53 | 17-00001-001 | Ferrite BeadU12E-PROM “‘SPACE DUNGEON'’™

Dt | 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U12

D2 | 13-14001-001 [Diode Wa004U13E-PROM ‘SPACE DUNGEON'’™
D3}13-14001-001 | Diode IN400126-00001-024 | Socket 24 Pin Dip for U13
D4 | 13-14001-001 | Diode IN4001u14E-PROM ‘‘SPACE DUNGEON''™

D5 | 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U14

D6 | 13-14001-001 | Diode IN4001U15E-PROM “SPACE DUNGEON"'™
D7_|13-14001-001 | Diode IN400126-00001-024 | Socket 24P Dip Used For E-PROM
D8 =| 13-14001-001 { Diode IN4001U16E-PROM ‘SPACE DUNGEON'™

D9 | 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U16

D10 | 13-14001-001 | Diode IN4001U17E-PROM ‘SPACE DUNGEON"™

D11 | 13-14001-001 | Diode IN4001 26-00001-024 | Socket 24 Pin Dip for U17

D12 | 13-14001-001 | Diode IN4001U18E-PROM “SPACE DUNGEON’’™

Q1 — |14-00001-001 | Transistor NPN Darlington TIP120 26-00001-024 | Socket 24 Pin Dip for U18

Q2 | 14-00001-001 | Transistor NPN Darlington TIP120u19E-PROM ‘SPACE DUNGEON''™

Q3 | 14-00001-001 | Transistor NPN Darlington TIP120 26-00001-024 | Socket 24 Pin Dip for U19 Q4 | 14-00001-001 | Transistor NPN Darlington TIP120 U20 | 15-00004-001 | Paralell 1/0 68A21 Q5 | 14-00001-001 | Transistor NPN Darlington TIP120 U21_ | 15-20138-001 | Decoder 1 of 8 (138) Q6 | 14-00001-001 | Transistor NPN Darlington TIP120 U22 | 26-00002-016 | ROM Select

Q7—_{14-00001-001 | Transistor NPN Darlington TIP12026-00001-014 | Socket 24P Dip for U22

Q8 | 14-00001-001 | Transistor NPN Darlington TIP120 U23_ | 15-20004-001 | Inverter, HEX (74LS04)

a9Not UsedU24Not Used
Q10 | 14-00001-001 | Transistor NPN Darlington TIP120U25Not Used
Q11|14-00001-001 | Transistor NPN Darlington TIP120U26Not Used
Q12_ | 14-00001-001 | Transistor NPN Darlington TIP120U27E-PROM “SPACE DUNGEON’'™

ui __|26-00002-016 ROM Select 26-00001-014 |Socket 14P Dip for U27 26-00001-014 | Socket 14P Dip. for U1 U28_ | 15-20138-001 | Decoder 1 of 8 (138)

U2__|15-20138-001 | Decoder 1 of 8 (138)u29ROM Select
U3E-PROM “SPACE DUNGEON''™26-00001-014 | Socket 14P Dip Used For ROM Select

26-00001-024 | Socket 24 Pin Dip for U3 15-00004-001 | Paralell 1/0 6821

U4E-PROM “SPACE DUNGEON'’™25-00001-001 | Connector Header 50PIN

26-00001-024 | Socket 24 Pin Dip for U4 25-00001-001 | Connector Header 50PiN

U5E-PROM “‘SPACE DUNGEON’™25-00001-001 | Connector Header 5OPIN

26-00001-024 | Socket 24 Pin Dip for U5 25-00002-014 |Connector 14 Pin Header .156 Center 25-00002-014 {Connector 14 Pin Header .156 Center 25-00002-014 | Connector 14 Pin Header .156 Center 25-00002-014 {Connector 14 Pin Header .156 Center

Page 58

COIN PROCESSOR BOARD LAYOUT

RXX KOE 005054 KKK bad Fy z

15-00010-001 KERN BEGEE KKK

AY

Page 59

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 60

COIN. DOOR, ie Tea Ne

2 os | -

NOTE ~ # DENOTE AAVERS FIRE JoRSTICN,

1 i | VIDEO PROCESSOR Eis 8) ROB a 08-90001-001 ‘ON, DOOR

PROCESSOR

aa serermnen as l i L a ~ _ FRavsrommen 8

Page 61

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 62

NOTES

Page 63

WARRANTY

TAITO AMERICA CORPORATION warrants that its printed circuit boards and parts are free from defects in material and workmanship under nomal use and service for a period of ninety (90) days from the date of shipment. Seller warrants that its monitors are free from defects in material and workmanship under normai use for a period of thirty (30) days from the date of shipment. The factory also warrants all socketed parts for a period of ninety (90) days when furnished with the game serial number. If the above products fail to conform to this Warranty Taito America Corporation has the option to repair, replace, or credit the Buyer’s account. The Buyer must notify Taito America Corporation in writing upon finding the defective product. Buyer must also return the defective product prepaid to Taito America Corporation's factory located in Elk Grove Village, Illinois. \f Taito America Corporation determines upon examining the returned product that damage was caused by accident, misuse, neglect, modification, or improper repair or testing, this Warranty will be void. Inno event will Taito America Corporation be held for loss of profits to Buyer.

Page 64

TAITO AMERICA CORPORATION 1256 Estes Avenue, Elk Grove Village, IL 60007 Telephone (312) 981-1000 Telex 25-3290