CATHODE RAY TOMES

Chopper Parts Catalog (Sept 1974)

Chopper I (US Ver 2) (SNK, 1988) · Parts Catalog · 19 pages · 9 sections · original scan

Page 1

Midwayt GAME NO. 583 SEPTEMBER, 1974

PARTS CATALOG

10750 WEST GRAND AVENUE FRANKLIN PARK, ILLINOIS, 60131, U.S. A.

PHONE: (312) 451-1360 CABLE ADDRESS: MIDCO TELEX NO.: 72-1596

Page 2

TABLE OF CONTENTS

Page No.

GENERAL INSTRUCTIONS 1

GENERAL ADJUSTMENT INFORMATION 2

LAMP & MOTOR REPLACEMENT 3

CABINET BREAKDOWN DETAIL 4

CHOPPER, COMPONENT LAYOUT 5

CONTROL BOX ASSEMBLY 6—7

TOWER ASSEMBLY 8—9

TARGET ASSEMBLY 10—11

TAPE DECK 12—13

PLAYFIELD COMPONENTS 14—15

ADDITIONAL PARTS LIST 16

EQUIPMENT CHART Inside Cover

Page 3

GENERAL INSTRUCTIONS FOR ‘‘CHOPPER’’

  • INSTALLATION: A. Fasten leg levelers to four legs and attach to cabinet with provided bolts. B. Prepare helicopter for flying: . Open both rear doors. . Remove rear scenery panel. Four wood screws hold it in place. . Remove shipping bracket holding helicopter to playfield. . Attach counter weight (shipped in coin box). Position counter weight even with edge of tape and lock in place with nut. This position has been adjusted at the factory for best flying conditions.
  • Reassemble rear scenery panel. C. The power is controlled by a switch located in the rear corner on the bottom of the cabinet. Plug into A.C. only, 115 volts, 60 cycles. In low line areas (100 volts or less), a boost in the output voltage of the transformer may be achieved by removing the wire from the 115 volt tap of the transformer and re-wiring to the 105 volt position. D. In the event the game is tilted or the line cord is removed, any credits accumulated will be reset to zero.
  • EXTENDED PLAY ADJUSTMENT: Located on Logic Board (PC 583-904) and is adjustable from 5 to 14 hits by re-wiring jumper as indicated on the board. Extended play awards 50% additional flying time.
  • COIN ADJUSTMENT: Located on Logic Board (PC 583-904) and may be adjusted from 1 to 4 coins per play be re-wiring jumper as indicated on the board.
  • PLAYS PER COIN: Located on Logic Board (PC 583-904) and may be adjusted to 1 or 2 plays per coin by re-wiring jumper as indicated on the board.
  • TIME ADJUSTMENT: Located on Logic Board (PC 583-904) and may be adjusted at 1 minute to 2 minutes 40 seconds, (that is 1 minute Ist position, 1-20 - 1.40 — 2.00 — 2.20
  • 2.40 last position), by re-wiring as indicated on the board (——» increase).
  • PLAYFIELD SERVICE SWITCHES: Located on mech panel. To service, follow instructions in back-box area.
  • PHOTO-CELL SENSITIVITY CONTROLS: Located on Photo-Cell Detector (PC 583-924) on the lower back door. To increase sensitivity (makes target easier to hit), rotate controls as indicated.
  • VOLUME CONTROLS: Located on Amplifier (PC 583-926) on lower back door. To increase volume, rotate as indicated. PWNHH

10750 WEST GRAND AVENUE FRANKLIN PARK, ILLINOIS

Page 4

GENERAL ADJUSTMENT INFORMATION FOR “CHOPPER”

These adjustments are to be made only if the game malfunctions.

  • PITCH CONTROL LINK: With the pitch control handle (right handle) at its center position (straight up), adjust the thread portion of the link until the helicopter rises vertically ‘‘only’’, when power is applied (a slow drift is okay).
  • POWER CONTROL POT: A. Disconnect motor speed edge connector (PC 583-913). B. Adjust (5k) copter pot (left handle) for 250 ohms. (D Connect ohm meter between G-R and W-G at pot.
  • Loosen set screw and remove gear.
  • Rotate pot to 250 ohms.
  • Replace gear, tighten set screws and connect jack at PC 583-913. C. Connect D.C. volt meter across copter wipers and adjust trim pot on copter motor speed (PC 583-913) to 2 V.D.C. at zero handle position. With handle at full power, meter should read 5 V.D.C.
  • ae POT ADJUSTMENTS: Remove amplifier edge connector (PC 583-926). "i Adjust pot to 250 ohms (left handle). (D Connect ohm meter between W-B and BLU-W at pot.
  • Loosen set screw and remove gear.
  • Rotate pot to 250 ohms.
  • Replace gear, tighten set screw, and connect jack at PC 583-926.
  • SOUND POT: A. Remove amplifier edge connector PC 583-926. B. Adjust pot to maximum resistance, (approximately 6.25k ohms) (right handle). () Connect ohm meter between wiper (center |ead) and either outside lead,
  • Loosen set screw and remove gear.
  • Rotate pot to 6.25k ohms.
  • Replace gear, tighten set screw, and connect jack at PC 583-926.
  • CREDIT BUTTON: Credit switch must be adjusted to break before make. Failure to adjust switch as indicated will result in permanent damage to Logic Unit (PC 583-904),
  • BOOM COUNTER BALANCE WEIGHT: A. Position dampening pad to its center position. B. Be sure power control pot is set properly. C. Position ‘‘pitch’’ control handle to center position. D. Move ‘‘power’’ contro! handle to its maximum up position (do this slowly). E. Helicopter must rise to its maximum up position (boom hits top cap). Adjust weight in or out to have boom hit its stop within the last 10° of handle travel. F. |f the helicopter has a very sensitive control in the vertical flight, the dampening pad may be adjusted up to apply more pressure. NOTE: Any time time you re-adjust the dampening pad, you must re-adjust the counter balance weight (Item ‘‘E’’).

10750 WEST GRAND AVENUE FRANKLIN PARK, ILLINOIS

Page 5

LAMP_& MOTOR REPLACEMENT LAMP ADJUSTMENT 1S ACCOMPLISHED BY FOCUSING THE LENS.

THIS 1S DONE BY ROTATING THE LENS HOUSING (MARKED "A") 7

INSIDE THE HELICOPTER. TO OBTAIN PROPER FOCUS THE SPOT

OF LIGHT SHOULD BE ADJUSTED AT A DISTANCE OF 3" AT THIS

DISTANCE THE SPOT OF LIGHT SHOULD BE APPROX. |" DIA. DETAIL /"APPROX-

WITH CLEAR, SHARP EDGES. SEE DETAIL :

NOTE: 3 VOLTS MAX. FOR LAMP

  • REMOVE THESE THREE SCREWS TO OBTAIN ACCESS FOR LAMP REPLACEMENT & ADJUSTMENT.

REMOVE THIS SCREW FOR LAMP REPLACEMENT. REMOVE LAMP SOCKET PULL OLD LAMP OUT & REPLACE MOTOR LABEL WITH MIDWAYS /7-3-129 OR G.E. 253.

NOTE: BE SURE LAMP IS IN THE

PROPER MOTOR WIRING

CAUTION: /F WIRED IN- DETENTED POSITION IN SOCKET.

CORRECTLY YOU WILL BURN OUT THE LAMP.

Page 6

CABINET BREAKDOWN DETA/L

NOTE: In rare cases where doorways are under 34/2’’ (width of cabinet), provisions have been made to disassemble upper parts of cabinet.

STEP 1: Remove background scenery “‘E’’.

STEP 2: Remove front and side viewing glass. Remove top cleats ‘‘A’’ (shown in detail), as well as inside members of front corner brackets ‘‘D’’. In order to remove side glass, the rear wooden retaining members ‘‘B’’ must be taken off.

STEP 3: Remove top portion of cabinet Remove 4 hex. head bolts (2 on each side) from structural members ‘‘C’’ supporting the top. Then the front glass edge re tainers should be removed. This will then allow the entire upper portion of the cabinet to be removed. Remember to disconnect the cable quick-disconnect.

STEP 4: Remove the four fegs. This will then allow the remaining portion of the cabinet to be rotated onto its side and will then fit thru most doorways 28’ wide (minimum width).

Reverse steps for assembly.

10750 WEST GRAND AVENUE FRANKLIN PARK, ILLINOIS

Page 7

foo} L Tens BORbe | gb Tea aN}

mM Dp

7408 7408 CHOPPER Locic PC. 5B3-904-1 commpoNeT UstouT

Page 8

CONTROL BOX

Page 9

NO. 583 CHOPPER — CONTROL BOX ASSEMBLY PRICE LIST ORDER BY PART NUMBER ONLY trem| Part Ne | DESCRIPTION [Price 583-018 CAM ASSEMBLY (2 REQUIRED) 17-7-115 DRIVE PIN 3/16 DIA. (2 REQUIRED) 17-42-97 NYLINER (2 REQUIRED) 583-116 BRACKET — SPEED CONTROL 17- 104-05 LOCKWASHER #1/4 (2 REQUIRED) 17-103-19 LOCKNUT 1/4-20 (2 REQUIRED) 17-17-62 ROLL PIN 17-42-96 GEAR (48 T., 32 P.) 583-704 GEAR PIN 17-101-309 | SET SCREW 8-32 X 1/4 (2 REQUIRED) 583-723 PINION — 16 TOOTH (2 REQUIRED) 17-13-143 POT 5K 17- 100-38 “E” RING (2 REQUIRED) 17-13-21] POT 10K 17-100-25 “E" RING (4 REQUIRED) 601-131-1 SWIVEL BRACKET 10-139 SPRING 583-007 HANDLE ASSEMBLY R.H. 10-179-1 SPRING 10-538-1 WIRE FORM 600-130 LOCK BRACKET PIN STOP (2 REQUIRED) COVER ASSEMBLY CENTERING BRACKET LOCKING SPRING LOCKNUT 1/4-20 (2 REQUIRED) LOCKWASHER #1/4 (2 REQUIRED) ROLLER — SPACER MOUNTING BRACKET PIVOT BRACKET SUB. ASSEMBLY CONTROL BOX SUB. ASSEMBLY 17- 197- 41-32 | GRIP - BLACK R.H. 17-198-41-33 | GRIP - RED L.H. 583-006 HANDLE ASSEMBLY L.H. 17-101-309 | 8-32 X 1/4 SET SCREWS (4 REQUIRED) 583-705 PLUNGER 22-001 STOP BRACKET ASSEMBLY 426-1200 COIL 983-005 GEAR & PIN SUB. ASS'Y. — Part No’s. 7, 8 &9 WOUDMNE wre

PRICES SUBJECT TO CHANGE WITHOUT NOTICE PAGE 7

Page 10

MIDWAY MFG CO 7 ) af teh TOWER ASSEMBLY

Page 11

NO. 583 CHOPPER - TOWER ASSEMBLY PRICE LIST ORDER BY PART NUMBER ONLY rem[ parr we | esceiprion | ice | 17-101-593 | 8-32 X 1/4 SCREW 600-128 TOP 583-719 CONTROL ROD 583-015 BOOM SUPPORT ASSEMBLY 583-027 BOOM ASSEMBLY 583-051 BRACKET & PAD ASSEMBLY 600-127 CUP BOTTOM 17- 104-34 5/8 X 7/16 X 1/16 WASHER 583-016 TOWER TUBE SUB. ASSEMBLY 600-129-1 ENCLOSURE (2 REQUIRED) 17-085-41-40 | GROMMET - RUBBER 583-023 MOTOR ASSEMBLY 583-011 SKID ASSEMBLY 583-022 CHASSIS ASSEMBLY 983-025 HELICOPTER BODY KIT 17-101-302 | 6-32 X 3/16 LG. SET SCREW 17-193-42-37 | HELICOPTER PROP. 583-708 BLOCK, MOTOR PIVOT 583-712 PIVOT PIN 600-733 COLLAR 17-101-302 | 6-32 X 3/16 SET SCREW 583-028 WIPER ASSEMBLY (3 REQUIRED) 17-101-520 | 5-40 X 3/8 PAN H.M.S. WOUMMP WE

17-100-18 “E” RING 601-705-1 LINK - HORIZONTAL 600-724-1 ADJ. LINK BELL CRANK SUB. ASSEMBLY pWor BRACKET S. A. IN 1/4--20 HEX. NUT COUNTER BALANCE WEIGHT MOUNTING BRACKET, SOCKET LAMP G.E. #253 2.5V COVER BRACKET SOCKET LENS TUBE ASSEMBLY CHAIN ASSEMBLY COMPLETE HELICOPTER ASSEMBLY 983-008 601-105 600-707 17- 103-18 600-727 583-141 17-3-129 583-130 17-31-22 583-024 583-026 583-021

PRICES SUBJECT TO CHANGE WITHOUT NOTICE PAGE 9

Page 12

TARGET ASSEMBLY

TARGET 1 TARGET 2 TARGET 3 TARGET 4 NW. NE. SE. SW.

MIDWAY MFG CO

Page 13

NO. 583 CHOPPER - TARGET ASSEMBLY PRICE LIST ORDER BY PART NUMBER ONLY rem] part no | escriprion | PRICE 17-101-569 | 6-32 X 1/2 OVAL HD. SCREW (2 REQUIRED) 17-101-555 | #6 X 5/16 HEX. HD. S/T M.S. (6 REQUIRED) 17-101-527_ | 4-40 ROUND HD. M.S. (4 REQUIRED) 583-049 LIMIT SWITCH ASSEMBLY (TOP) 583-113 LIMIT SWITCH BRACKET 17-21-36 9 POINT MALE AMP HOUSING 17-101-612 | 8-32 X 3/8 PAN HD. — MONEL M.S. 17-3-127 MOTOR - TARGET 583-105 MOTOR PLATE 17-42-02 3/16 CLAMP (2 REQUIRED) 983-036 BRACKET BEARING & MOTOR SUB. ASS'Y.

  • “CE” RING WORM ASSEMBLY #4-40 X 1/8 LG. SOCKET SET SCREW GEAR ASSEMBLY TARGET UNIT SUB. ASSEMBLY LIMIT SWITCH BRACKET LIMIT SWITCH ASSEMBLY (BOTTOM) SWITCH BACKUP STRIP SPACE CREATURE #1 ASSEMBLY SPACE SHIP ASSEMBLY SPACE CREATURE #8 ASSEMBLY SPACE CREATURE #2 ASSEMBLY SLIDE BAR ASSEMBLY SLIDE BAR ASSEMBLY SLIDE BAR ASSEMBLY SLIDE BAR ASSEMBLY MOUNTING BRACKET MOUNTING BRACKET MOUNTING BRACKET MOUNTING BRACKET EXTENSION SPRING EXTENSION SPRING EXTENSION SPRING EXTENSION SPRING STRAIN RELIEF BRACKET COMPLETE #1 TARGET N.W. COMPLETE #2 TARGET N.E. COMPLETE #8 TARGET S.E. COMPLETE #4 TARGET S.W. 583-111 583-047 90-126-1 583-044 583-043 583-046 583-045 583-035 583-032 583-034 983-034 583-125 583-125 583-125 583-125 10-225-1 10-225-2 10-225-1 10-225-1 583-147 583-040 583-039 583-041 583-042 -40 EA. -40 EA. .00 EA. .60 EA. -00 EA. 00 EA. .70 EA. 43.90 EA. 43,90 EA. 43.90 EA. 43.90 EA.

PRICES SUBJECT TO CHANGE WITHOUT NOTICE PAGE 11

Page 14

NO.583 CHOPPER -_ TAPE DECK CHASSIS COVER 2 CHANNEL - CARTRIDGE TYPE

52-15

(COMPLETE TAPE UNIT 52-017)

HEAD MTG. ASS'Y. 52-003

52-103

, DRIVE BELT \ 17-243-41-17 10-212-1 FLYWHEEL ASS'Y 52-001

"CHOPPER" TAPE CARTRIOGE 52-701 17-3-131 (NOT SHOWN) > 52-703 (3-REQD.)

17-O80- MOTOR - TAPE DECK* 40-40905 (50 € 60C.) THIS MOTOR REPLACES 52-706

WHEN CHANGING TO B®) NEW STYLE MOTOR, BE SURE TO ORDER CORRECT PULLEY § HEX. HD. NYLON SCRI CHASSIS ASS'Y 10-32 X 1/4 52-008

52-709 (60C.) 52-710 (50C)

SET SCREW 6-32 x 1/4

17-226

XI7-100-21

Page 15

NO. 583 CHOPPER — TAPE DECK (2 CHANNEL) PRICE LIST ORDER BY PART NUMBER ONLY

10-2121 SPRING — DETENT 17-3-131 TAPE CARTRIDGE 17-080-41-13 | RUBBER GROMMET X17-100-21 “E" RING (7/32") 17-226-42-16 | PLASTIC SNAP BUSHING 40-40905 MOTOR — TAPE DECK (50 & 60C.) 1600 RPM 52-001 FLYWHEEL ASSEMBLY 52-003 HEAD MOUNTING ASSEMBLY 52-008 CHASSIS ASSEMBLY 52-009 BEARING PLATE ASSEMBLY 52-017 COMPLETE TAPE UNIT W/O CARTRIDGE 52-102 TOP PLATE 52-103 TAPE GUIDE 52-115 CHASSIS COVER 52-701 MOUNTING POST (2~11/16" LG.) 52-703 MOTOR MOUNTING POST (3 REQUIRED) 52-706 MOUNTING POST (1-1/2” LG.) 52-709 MOTOR PULLEY (60C.) 52-710 MOTOR PULLEY (50C.) 52-901 WASHER - SPECIAL 568-048 TAPE DECK MOUNTING BRACKET ASSEMBLY (2 REQUIRED) NOT SHOWN 583-923-88 | TAPE DECK PRE-AMP P.C.

PRICES SUBJECT TO CHANGE WITHOUT NOTICE DESCRIPTION | price | .20 EA. 8.00 EA. .20 EA. .20 EA. .20 EA. 16.00 EA. 9.50 EA. 5.80 EA. 7.20 EA. 10.00 EA. 95.00 EA. 1.20 EA. -80 EA. 3.20 EA. 1.20 EA. .60 EA. 1.70 EA. 2.60 EA. 2.80 EA. .20 EA. .70 EA.

36.00 EA.

Page 16

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 17

NO. 583 CHOPPER — PLAYFIELD COMPONENTS PRICE LIST ORDER BY PART NUMBER ONLY

DESCRIPTION

983-917VACUUM FORMED PLAYFIELD35.00 EA.
583-918-1BUILDING, VACUUM FORMED — N.W.8.00 EA.
583-918-2BUILDING, VACUUM FORMED - N.8.00 EA.
583-918-3BUILDING, VACUUM FORMED — N.E.8.00 EA.
583-9 18-4BUILDING, VACUUM FORMED — S.E.8.00 EA.
583-918-5BUILDING, VACUUM FORMED - S.W.8.00 EA.
17-9-96LYCHEN, GREEN (NOT SHOWN).20 EA,
17-9-98TREE (NOT SHOWN)-60 EA.
17-9-99TREE (NOT SHOWN).60 EA.
17-9-100TREE (2 REQUIRED) (NOT SHOWN).60 EA.
17-9-101TREE (NOT SHOWN)-60 EA.
17-9-151TOY CARS (NOT SHOWN)1.40 EA.
17-9-152TOY CARS (NOT SHOWN)1.40 EA.
17-9-153TOY CARS (NOT SHOWN)1.40 EA.

PRICES SUBJECT TO CHANGE WITHOUT NOTICE PAGE 15

Page 18

NO. 583 CHOPPER — ADDITIONAL PARTS LIST PRICE LIST ORDER BY PART NUMBER ONLY rem] parr wo] pescririon | ice

CD-24-300COIL2.40 EA.

G-30-2000D | LOCK & HIT KELAY COILS (2 REQUIRED) 2.00 EA.

M-34-2400RELAY COILS (6 REQUIRED)2.40 EA.
M-645-120PROGRAM UNIT6.00 EA.
MT-4360 CYCLE TRANSFORMER35.00 EA.
MT-4450 CYCLE TRANSFORMER39.00 EA.
17-3-1026V. ENM COUNTER10.80 EA.
17-3-130FLUORESCENT LAMP 30”5.20 EA.
17-41-576GASKET-20 EA.

17-034-32-05 | ON/OFF SWITCH .90 EA. 17-050-5-46 | LOCK (1350) WITH KEYS 3.40 EA. 17-093-102-48] LEG LEVELERS WITH NUTS (4 REQUIRED) . 40 EA. 17-175-3-32 | 4"’ DIAMETER SPEAKER (2 REQUIRED) 5.40 EA. 17-257-3-65 | A.C. LINE CORD (16 FT.) 4.60 EA.

549-128GRILL (2 REQUIRED)1.00 EA.
552-170GAME LEGS24.00 EA.
567- 106-1SWITCH PLATE.60 EA.
582-100VENT GRILL0 EA.

583-054 STEP-UP DRUM UNIT ASSEMBLY COMPLETE | 18.90 EA.

583-073REFLECTOR & FLUORESCENT ASSEMBLY22.00 EA.
583-107SCORE BILLBOARD FRAME1.90 EA.
583-145COIN BOX COVER1.40 EA.
583-146COIN BOX6.40 EA.
583-900GLASS (FRONT)16.60 EA.
583-900-1GLASS (SIDES)14.40 EA.
583-901SCORE PLEX.4.60 EA.

583-904-1-88 | GAME LOGIC BOARD 200.00 EA. 583-913-88 | COPTER MOTOR SPEED 59.00 EA.

583-919SCENERY BACKGROUND20.40 EA.

583-922-88 | TARGET MOTOR SPEED 114.00 EA. 583-924-1-88 | PHOTO DETECTOR 64.80 EA. 983-925-88 | POWER SUPPLY 48.00 EA. 583-926-88 | AMPLIFIER 67.00 EA.

MIOWAY MFG. CO. PAGE 16 ~— prices SUBJECT TO CHANGE WITHOUT NOTICE

Page 19

CHOPPER EQUIPMENT CHART COIL oe APPLICATION

A-26-12001_|Handle Release Coil.
CD-24-3001_|Program Unit ADVANCE Coil.

G-30-200 DC. | 2 | Lock and Hit Relay Coils. M-34-2400 DC| 6 | #1, #2, #3, #4 Target, Program and Extended Play Relay Coils. MISCELLANEOUS MT-43 1_ | 60 Cycle Transformer

MT-441_|50 Cycle Transformer

17-3-127 4 | Target Motors 6000 RPM. D.C. 40-40905 1 | Tape Deck Motor 1600 RPM.

583-0231_|Copter Motor 3000 RPM. D.C.

PRINTED CIRCUITS M-465-120 1_ | Program Unit

583-9041_|Logic Serial #101 - #177
583-904-11_|Logic Serial #178
583-9131_|Copter Motor Speed
983-9221_|Target Motor Speed
583-9231_|Pre-Amp
583-9241_|Photo Detector
583-9251}Power Supply
583-9261_|Amplifier