Off the Wall TM-372 1st Printing
Off the Wall (2/3-player upright) (Atari Games, 1991) · Technical Manual · 56 pages · 58 sections · original scan
1-372 Ist printing
iversal Kit ~< S4 _In allation Instruction v
Cocktail version. aa a Le yy ft , 7 a
- ‘na, & ; ~w 5. ae Saale “ a ex
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
THE WALL.
Conversion kit for two- or three-player upright games
Copyright © 1991 by Atari Games Corporation. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for substantial penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 per infringing transaction in certain cases. Infringers may also have to pay costs and attorneys’ fees and face an imprisonment of up to five years as well as fines of up to $250,000 in the case of individuals and up to $500,000 in the case of corporations. Atari Games Corporation will aggressively enforce its copyrights against infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game. Published by: Atari Games Corporation 675 Sycamore Drive P.O. Box 361110 Milpitas, California 95036 Printed in the U.S.A. 9/91 Produced by the Atari Games Technical Publications Department. Writing and Editing: Andrea Dencker Illustration and Design: Mary Ohanessian Sumner Off the Wali Universal Kit
NOTICE RE.
NON-ATARI
PARTS
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:
- Substitute non-Atari parts in the game.
- Modify or alter any circuits in the game by using kits or parts not supplied by Atari Games Corporation.
- All ground wires in the game are properly connected as shown in the game wiring diagram.
- The power cord is properly plugged into a grounded three-wire outlet.
- On games provided with an Electromagnetic Interference (EMD ground plane, be sure that the game printed-circuit boards (PCBs) are properly installed on the EMI ground plane and that the end board is securely installed with all screws in place and tightened. If you are still unable to solve the interference problem, please contact Customer Service at Atari Games Corporation. See the inside front cover of this manual for service in your area.
Off the Wal! Universal Kit
SAFETY
SUMMARY
The following safety precautions apply to all game operators and service personnel. Specific warnings and cautions will be found in this manual whenever they apply.
iii
CONTENTS
1 Installation How to Use This Manual .. Cabinet Eguipment Requirement Tools Required Inspecting the’ Preparing the Cabinet for the Kit Installation Assembling the:Control Panel.. vo Connecting the JAMMA Harness......: Installing the Off the Wall Game PC! Installing the Bezel, Decals; Labels, and Attraction * Assembly . Setting the Coin and Game Option: Maximizing Earnings Game Play Off the Wall Universal Kit
Sound Board Test Controls Test. RAM Test . ROM Test . Playfield Stamp Test
iplor Purity Test peavergence Test Troubleshooting and Maintenance
‘Troubleshooting Removing and Replacing the Joystick rols Removing and Replacing the Whirly-Gig Controls .OMs and RAMs...
de the List of Ulustrations that foll ee Schematic Diagrams See the List of Illustrations that follows.
Off the Wali Universal Kit
St ‘d t is t a CS SA e et Figure 4-2 oa Short-Throw Joystick
Ive
Figure 1-1 Figure 1-2
Figure 1-3
Figure 1-4
Figure 1-5
Figure 2-1 “Figure 2-2 Figure 2-3 Figure 2-4 “Figure 2-5—
Figure 2-13 Figure 2-12 Figure 4-3. Whirly-Gig (Encoder Pot) Assembly (A049722-01 A).... eo USTRATION S Figure 4-4 Off the Wall Game PCB Assembly with Whirly-Gig Controls (4049727-02 A) and with Joystick Controls (A049727-01 B)... we 16 Figure 4-5 JSA (JAMMA Stand-alone Audio) TI PCB Assembly (4048974-07 A Installed Kit Parts... Locations of Control Panel Holes to be Drilled. Locations of Control Panel Holes to be Drilled (Three-Player Game)......... 1-7 Hole-Cutting Template for Off The ‘Wall Kit Control Panel... Instructions Label for Monitor — Bezel Figure 5-1 1¢ Wall Game PCB Assembly atic Diagram (049726-01 B).... 5-2 _ Figure 5-2
Quick Self-Test Screen Select-“Fest Screen sd. Statistics Screen Histogram Screen. Game-Options-Screen .
Barts for Off the Wall Universal Kit “with Whirly- Gig Controls (A049752-02 D) and with J Controls (171097-002)......
Off the Wall Universai Kit
N o
CHAPTER 1
41S MANUAL
The Off the Wall” conversion kit provides several options. Standard in the kit are two sets of whirly-gig or joystick controls and ail parts necessary to convert an upright game cabinet. % To install three sets of controls in
your wider cabinet, you can order additional controls (see page 1-8 for a list of parts). ¢ In addition, a separate version of this kit is available to install in cocktail games. A separate
supplement to this manual, CO-372-01, describes how to install that version. # This
manual provides information for installing, testing, and troubleshooting the Off the Wall™ conversion kit. # Chapter 1 describes how to install the Off the Wall kit in your cabinet. This chapter also describes game play. + Chapter 2 contains self-test procedures and additional diagnostic tests. The self-test is important in the Off the Wall game. You can
troubleshoot the PC boards, main circuits, and controls using the screens in the self-test.
You shouid regularly test the boards and controls with the self-test to keep your game in peak condition and at top earnings. # Chapter 3 contains troubleshooting and maintenance procedures for the controls. # Chapter 4 contains the kit parts list and parts illustra-
tions. ¢ Chapter 5 contains the schematics for the Off the Wall game PCB.
Installation:
Cabinet Equipment Requirements
Table 1-1 lists the equipment required in the cabinet into which you are installing the Off the Wali kit.
Tools Required
© Drill with a 1/2-inch and 5/16-inch drill bits
- Phillips screwdriver ¢ Flat-blade screwdriver
- Socket wrench set and ratchet
- 5/32" hex wrench
Equipmen: Spec ation
Color RGB monitor Separate positive horizontal and vertical sync or negative composite sync Horizontal mounting Horizontal frequency: 15.750 KHz Vertical frequency: 60 Hz Video input: 1V to 8V peak-topeak positive polarity Video Display
Control Panel Metal only e 8Q, 10W
+5 VDC or +12 VDC
Three-conductor with ground +5 VDC + 0.25V @ 3.0 amps +12 VDC @ 1.0 amp
-5 VDC @ 1.0 amp (optional) Speaker
Coin Counter
Power Cord
Power Supply
Table 1-1 Equipment Requirements
1-2 Off the Wall Universal Kit
- Wire cutters and strippers © Straight edge
- Squeegee ° X-ACTO™ knife
- Insulated wire connectors (if you are installing a new JAMMA harness)
- Carbon paper
° Saber saw
° File
- Bandsaw
¢ Tape or glue
Part No. Deseri
72-6608S #6 x 1/2"-Long, Type AB, Pan-Head, Cross-Recessed Screws (4) 75-5112B #10-24 x 3/4"-Long Black Carriage Bolts (12) 177026-0040 #10-24 Nut/Washer Assemblies (12) 038158-01 Product |.D. Label
039450-01 FCC Compliance Label 047205-01 Attraction Shield 047209-01 Control Panel Cover 049751-01 Control Panel Decal
049750-01 Side Panel Decals (2) 049749-01 Attraction Panel Film 049747-01 Monitor Beze! with Graphics 049743-01 Game Instructions Label for Control Panel
141026-001 5'-Inside-Diameter Ferrite Split Beads (2) 160044-001 Snap-Action Switches (4) A049722-01 Encoder Pot Whirly-Gig Control (2)* 175014-1040 #10 Flat Washers (12)
178032-002 #10 Wire & Cable Tie 178237-001 Red Button Assemblies (2) 178237-005 — Blue Button Assernblies (2) 178265-001 —_L-Style Nylon Standoffs (4)
178283-008 Indicator Plates Labeled “Start/Action” (6)* A046501-01 JAMMA Harness Assy. A049753-01 Off the Wall Kit Game Board Set TM-372 Off the Wall Universal Kit Installation Instructions (with control panel templates) "Your kit may instead include two joystick controls (part no, 174097-002) and six START/TURBO indicator plates (178283-012). Packaging materials are not listed, All parts are a quantity of 1, except as noted in parentheses.
Table 1-2 Contents of Off the Wall Kit
Off the Wall Universal Kit
owores.on| vation Fira 047205-01 =
tems Not Shown ‘04650101
“41c26-001 Spit Fertte Bead ‘7032-002 Cable Te
‘, | osrso01 Silo Panei Decal
A008759-02 Of The Wat Po ay. : (ul Veron) y hoss7s31 = On THe Wal POR Ay,
| ‘ed Deca! | = | (Ways Version) |
ik {rdassa0s
| : | ic | US | non |
Simoot
| xeon Deni | = | pices |
| 160088-001 | ge | tox escrow |
| snap-atton Swicn| | SN | {pieces} |
(places er 2piayer| Sacer payer ‘re2sr001 s Red Bution Assy. De iS (2 places) fom:
| sreaeo.o12| | 178297-006, | i | . |
| START/TURBO| | Groen Btn | i | i |
| indeator Plate | os | i |
(unyatek Veron) (vise (orspiaces)| y7you7002| Way, Shoe Pow Gold Contact, bk Kno 7551128
| ‘is | ck | Nomaat | |
| 2°391e8)| | ——478297.008 | ‘Coniago Bot | |
| onreetet2!) | ete Suton han. | (Gor replaces) | |
| ane | Dee | one | {77028-5000 |
| Ls | ¥ | #10-24 Nut |
4720901 Washer Assy
| ‘cuPanat | Gover} —- | ‘ngora2-01 | or'2paces) |
| auorsi-o1 | why | ‘re0t8-1oa0 |
cot Panel Decal {ErooderPot Assy) | MO Flt Washer
| nar | {eer pines) | {Por 2paces) |
Decsi
| 009743-01| | ‘Blue | | 178237-005 |
1 Panas| | Be, ‘lor Baton Assy Instructions Label sreza7-001 Red Button Assy. (2 places) +176263-008 [STARTIACTION Inieator Pat (4or6 places)
Figure 1-1 Installed Kit Parts
Inspecting the Kit
Check to see that you have al! the parts listed in the kit parts list in Table 1-2. If any part is missing or damaged, contact your distributor with the Off the Wall kit serial number, part number, and description of the missing or damaged parts, and date received. (2 places)
17283-008 ‘STARTIACTION Indeator Pate (Wiry-Gig Vernon) (40r6 places)
Installation Off the Wall Universal Kit
Wire
| Pin Color | Signal | Instructions |
Component Side
| 1 | BN | GND | Connect to the 5V RTN (GND) terminal on the power supply. However, if you have 12V RTN, |
connect one of the BN wires at pin 1, 2, A, or B to the 12V RTN terminal.
| 2 | BN | GND | Same as pin 1. |
| 3 | R | +5V | Connect the red +5V encoder pot wire of the left player to this pin. If you use joysticks, con- |
nect to the +5V terminal on the power supply. However, if your power supply has a +SENSE terminal. connect one of the R wires at pin 3, 4, C, or D to +SENSE instead of +5V.
| 4 | R | +5V | Same as pin 3. |
| 5 | OR | -5V | Connect to the -SV terminal of the power supply. If -5V is not available, connect to the 12V |
RTN or the 5V RTN (GND) or leave it unconnected. NOTE: If you do not have (or use) -5Y, the maximum power to the speaker will be reduced by half.
| 6 | Y | +12V | Connect to the +12V terminal of the power supply. |
If your coin counter(s) require 12V, also connect to the + side of the coin counter(s). 7 Key
| 8 | BUM | COINCTR1 | Connect this wire to one side of the left 12V coin counter. Note: Do not use 24V counters. |
Connect the + side to +5V or +12V on the power supply, as appropriate. 9 Not used
| 10 | BN | SPKR + | Connect to the + terminal on the speaker. (This wire is part of a twisted pair.) |
11 Not used
| 12 | R | RED | Attach to the video display. |
| i3 | BU | BLUE | Attach to the video display. |
| 14 | BK | VIDEO GND | Attach to the video display. |
| 15 | w | SELF-TEST | Use this wire if you want an external self-test switch. However, the kit already has a self-test |
switch on the PCB. (/f you connect an external self-test switch, switch off the switch on the PCB. Connect the wire to the N.O. terminal on the external self-test switch. Connect the common terminal of the switch to a BK/W wire [GND].)
| 16 | Y | LT COIN | Connect to the N.O. terminal of the left coin switch. Connect the common terminal of the |
switch to a BK/W wire. 17 W/BK — JAMMA START1JAMMA start switch (optional)
| 18 | W/BN | LT UP | Connect the orange encoder pot wire “CLK” of the left player to this pin. If you use joysticks, |
this signal is LT JOYST UP. Connect to the N.O. terminal of the switch. Connect the common terminal of the switch to one of the BK/W wires.
| 19 | WIR | LT DN | Same as pin 18. Connect the yellow encoder pot wire “DIR” of the left player to this pin. If you |
use joysticks, this signal is LT JOYST DN.
| 20 | WOR | LT JOYSTLT | Same as pin 18. Used only if joysticks are installed. |
| 21 | Wily | LT JOYST RT | Same as pin 18. Used only if joysticks are installed. |
| 22 | WIGN | _LTSTART/ACTION Connect this wire to the N.O. terminal of both left START/ACTION switches (START/TURBO |
switches if joysticks are installed). Connect the common terminals of the switches to one of the BK/W wires.
| 23 > | W/BU | Notused |
| 24 | WIV | Not used |
| 25 | W/GY | Notused |
| 26 | =«CNV | Not used |
| 27 | BK/W = GND | Connect the green ground encoder pot wire of the left player to this pin. If you use joysticks, |
connect one of the BK/W wires at pin 27, 28, e, and f to the negative sense terminal of the power supply (if it exists) and one to the common terminals of the coin switches, Connect two of these wires to the common terminals of the control switches on the control panel.
| 28 | BK/W | =GND | Same as pin 27. |
Table 1-3 JAMMA Pin and Wire Connections
Off the Wall Universal Kit Installation
Wire
| Pin Color | Signal | Instructions |
Solder Side
| A | BN | GND | Connect to the 5V RTN (GND) terminal on the power supply. However, if you have 12V RTN, |
connect one of the BN wires at pin 1, 2, A, or B to the 12V RTN terminal.
| B | BN | GND | Same as pin A, |
| c | R | +5V | Connect the red +5V encoder pot wire of the right player to this pin. If you use joysticks, con- |
nect to the +5V terminal on the power supply. However, if your power supply has a +SENSE terminal, connect one of the R wires at pin 3, 4, C, or D to +SENSE instead of +5V.
| D | R | +5V | Same as pin C. |
| E | OR | -5V | Connect to the -5V terminal of the power supply. If -5V is not available, connect to the 12V |
RTN or the 5V RTN (GND) or leave it unconnected
| F | Y | +12V | Connect to the +12V terminal of the power supply. |
H Key
| J | VW | COINCTR2 | Connect this wire to one side of the right 12V coin counter. Clip R26 on the game PCB if you |
use a second coin counter. Note: Do not use 24V counters. Connect the + side to +5V or +12V on the power supply, as appropriate. K Not used
| L | WwW | SPKR- | Connect to the - terminal on the speaker. (This wire is one of a twisted pair.) |
M Not used
| N | GN | GREEN | Attach to the video display. |
| P | BN | COMPSYNC | Altach to the video display. |
| R | GY | Service 1 | Optional: attach to the N.O. terminal of the 1st or main service switch. |
s Not used
| T | OR | RT COIN | Connect to the N.O. terminal of the right coin switch. Connect the common terminal of the |
switch to a BK/W wire.
| uU | Y/BK | JAMMA START2JAMMA start switch (optional) | |
| Vv | Y/BN | RT UP | Connect the orange encoder pot wire “CLK” of the right player to this pin. If you use joy- |
sticks, this signal is RT JOYST UP. Connect to the N.O. terminal of the switch. Connect the common terminal of the switch to one of the BK/W wires.
| w | YIR | RT DN | Same as pin V. Connect the yellow encoder pot wire "DIR"of the right player to this pin. If you |
use joysticks, this signal is RT JOYST DN
| x | Y/OR | RT JOYST LT | Same as pin V. Used only if joysticks are installed. |
| Y | YW | RT JOYST RT | Same as pin V. Used only if joysticks are installed. |
| z | YIGN | RT START/ACTION Connect this wire to the N.O. terminal of both right START/ACTION switches (START/TURBO |
switches if joysticks are installed). Connect the common terminal of the switch to one of the BK wires.
| a | Y/BU | Not used | |
| b | YN | Not used | |
| c | YIGY | Service 2 | Optional: attach to the N.O. terminal of the 2nd service switch. |
| d | GYW | —Notused | |
| e | BK/W | GND | Connect the green ground encoder pot wire of the right player to this pin. If you use joysticks, |
connect one of the BK/W wires at pin 27, 28, e, or f to the negative sense terminal of the power supply (if it exists) and one to the common terminals of the coin switches. Connect two of these wires to the common terminals of the control switches on the control panel.
| f | BKW | GND | Same as pine. |
Table 1-3 JAMMA Wire Connections, Continued
Installation Off the Wall Universal Kit
Wire
| Pin Color | Signal | Instructions | |
| 1 | BK | GND | Connect the green ground encoder pot wire of the center player to this pin. If you use joy |
sticks, connect to the common terminal of the center player control switches.
| 2 | Riw | +5V | Connect the red +5V encoder pot wire of the center player to this pin. However, not used |
if joy sticks are installed,
| 3 | Ww/BU | CCNT-CR | Not used. |
| 4 | WIGY | SERVICE 3 | Optional: attach to the N.O. terminal of the 3rd service switch. |
| 5 | wily | COIN CR | Not used. |
| 6 | w | JAMMA START 3 | Optional start software. |
| 7 | BN | UP3 | Connect to the N.O. terminal of the Joystick Up switch. Connect the commen terminal of |
the switch to the GND wire. If you use whirly-gigs, connect the orange encoder pot wire "CLK" of the center player to this pin.
| 8 | R | DN3 | Same as pin 7. If you use whirly-gigs, connect the yellow encoder pot wire “DIR” of the |
center player to this pin.
| 9 | OR | LF3 | Same as pin 7. Not used with whirly-gigs. |
| 10 | RT3 | Same as pin 7. Not used with whirly-gigs. | |
| 11. | GN | START/ACTION — Connect te the N.O. terminal of both START/ACTION or START/TURBO switches. Connect |
the common terminal of the switch to the GND wire.
| 12 | BU | _ | Not used. |
| 13° | OV | _ | Not used. |
15 a
Table 1-4 Third (Center) Player Pin and Wire Connections
1.187" Dia. il these holes wherever
Hi
‘
I t
H
T i
1 | H
H (asm 205 a, Holo | | —-—- -—--4--—--—--—--—-| —-|--| I Suggested distance from the |" 1“ 1.75" Dia. Hole 7 1.50" front of the control panel. (2 places) ' 3.00'—» Check that the whirly-gig/ | joystick controls have sufficient clearance before cutting holes. CL
Figure 1-2 Locations of Control Panel Holes to be Drilled (Two-Player Game)
1-6
Off the Wall Universal Kit
Preparing the Cabinet for
the Kit Installation
Figure 1-1 shows almost all kit parts installed in a typical cabinet. Use this illustration as a guide while you install the parts.
- Turn off power to the game, and unplug the power cord.
- Remove the following from the cabinet: ° Existing PCBs
- Game harness, if it is not Japan Amusement Machinery Manufacturers Association (JAMMA)— compatible
- Control panel decals, labels, and controls
- Side decals, graphics, and adhesive. If the cabinet sides are damaged, repair them before putting on the new decals. Installation
© Video display (monitor) shield, display bezel, attraction shield, and marquee.
- Wipe down and vacuum the cabinet. Paint the cabinet, if required.
Assembling the Control Panel
Parts Needed for this Kit
To assemble the control panel, you need the control panel hole-cutting template, which is printed on page 1-11. (If you would like an actual-size template for three player stations, contact Atari Games Customer Service at one of the locations printed on the inside front cover of this manual). Cut out the template sheet from this manual.
For Two Players If you are installing controls for two players, you will also need the following parts from the kit:
- Clear cover for the control panel
- Contro] panel decal
- Two red and two blue button assemblies
- Four snap-action switches
- 10.38"
- 3.38"— 2.98'— poo poo
! 2" -175 Dia. Hole + (3 places) S|
rd 1.66"
H \ 8.66" MS, ~s, 208 Sq. Hole _///1.187 Dia. Hole _, ss. (4 places) (6 places) “o
“Ne. Suggested distance from front of contro! panel. Make sure that the whirly-gig/joystick controls have sufficient clearance before cutting holes.
Figure 1-3 Locations of Control Panel Holes to be Drilled (Three-Player Game)
Installation, Off the Wall Universal Kit
Because few locations support wide games, Atari Games designed this kit to accommodate two players using joysticks or whirly-gigs. However, if you have a suitable cabinet, you can install this kit for three players. To fit three joysticks or whirly-gigs and sets of buttons onto a control panei, you must have a Street Fighter, Gauntlet, or similar style of cabinet with a wide control panel. Use the two extra START/TURBO or START/ACTION indicator plates already included in your kit.The additional parts required are available from Atari Games Customer Service and are as follows: Order these parts to add a third joystick controk © One joystick control (part no. 171097-002)
- Two green button assembiies (part no. 178237- 006) ° A third-player adaptor harness (part no. A049811-01) ¢ Four #10-24 x 3/4*-long black carriage bolts i (part no. 75-5112B) Parts Needed for Additional (Third) Player Controls ¢ Four #10-24 nut/washer assemblies (part no. 177026-0040)
- Two snap-action switches (pari no. 160044-001) Order these parts to add a third whirly-gig control: ¢ One whirly-gig control (part no. A049722-01),
- Two green button assemblies (part no. 178237- 006) e¢ A third-player adaptor harness (part no. A049811-01) ° Four #10-24 x 3/4"-long black carriage bolts (part no. 75-5112B) e Four #10-24 nut/washer assemblies (part no. 177026-0040)
- Two snap-action switches (part no. 160044-001) The four short wires on each whirly-gig control are connected to the JAMMA harness and 3rd-player harness as shown in Tables 1-3 and 1-4.
¢ Four control-panel indicator plates (labeled “Start/- Turbo” if you have joysticks or “Start/Action” if you have whirly-gigs)
- Two joystick or two whirly-gig controls
- Fight #10-24 x %"-long black carriage bolts, flat washers, and nut/washer assemblies for the joysticks or whirly-gigs ¢ Four #10-24 x %"-long black carriage bolts, flat washers, and nut/washer assemblies for the corners of the control panel cover
For Three Players If you are installing three player controls, you should use the two extra indicator plates included in your kit. The control-panel decai included is wide enough to
1-8 cover a wider control panel. You will need to purchase the additional parts listed in the box above.
Installing the Parts
- Using carbon paper, transfer the whirly-gig/joystick mounting pattern from the template to the contol panel. Save the template. Also refer to Figure 1-2 or 1-3 for the exact locations of all holes. 2, Drill four %" holes in the metal control panel for each whirly-gig’s/joystick’s mounting bolts.
- Using a saber saw, carefully cut out the large holes for the joysticks/whirly-gigs. Deburr the sharp edges with a file.
- Lay the plexiglass cover over the top of the control panel and mark the outside shape of the panel on the plastic. Also mark the button holes as close as possible to the locations shown on the template. Lasily, mark the positions of the four holes that will be used for securing the cover to the control panel. These four holes can be placed anywhere near the corners—wherever space permits.
- Using a bandsaw, cut the control panel cover to its correct outside shape.
Off the Wall Universal Kit
- Tape or glue the template to the plexiglass cover. To start the saber saw cut, drill a 1/2" hole inside the whirly-gig/joystick holes and the button holes. 7, Saw out the two large whirly-gig/joystick holes and the button holes.
- Drill the four 5/16" holes that will be used to mount the cover to the control panel and the 5/16" holes to mount the joysticks or whirly-gigs.
- To prevent injury, carefully deburr all the edges of the plexigiass cover.
- Install the control panel decal on the control panel. Use a sharp X-ACTO knife to trim the outside edge and to cut out the holes for the controls. Punch out the round instruction decals from the sheet and mount them over the whirly-gig/joystick holes: left = red, center (if used) = green, and right = blue. a
- Install the cover on the control panel with the four 3/4"-long carriage bolts, washers, and locknuts.
- Install the joysticks/whirly-gigs using the 3/4"-long carriage bolts and #10-24 nut/washer assemblies.
- Install the button assemblies and indicator plates as shown in Figure 1-1. For maintenance and servicing information on the joystick and whirly-gig controls, refer to Chapter 3 of this manual.
Connecting the JAMMA
Harness
- If your game cabinet does not already have a JAM- MA harness, install the JAMMA harness in the cabinet.
- Install the split beads on the harness as close to the PCB edge connector as possible. Hold the beads on the harness with the tie wraps included in the kit.
- Using Table 1-3 for wiring information, connect the JAMMA harness to existing component harnesses. Use crimp splices or butt soldering.
Connecting Power Wires 1, Connect the wires on the JAMMA harness to the wires for the power supply, as shown in Table 1-3. The Off the Wall kit requires +5V and +12V. If -SV is available, it should be used too. Tie off any other voltage wires on the power supply besides +5V, SV, and +12V. There is more than one wire for each voltage in the JAMMA harness. Use more than one wire for each voltage (connecting them as described in Table 1-3) so that the power wiring does not overload and burn.
Connecting Video Display Wires
Connect the wires designated for the red, green and blue video guns along with the sync and ground wires, according to Table 1-3.
Connecting Coin Door Wires
- Connect the wires on the JAMMA harness to the coin switches and meter according to Table 1-3.
- Connect one terminal of the door lamps to one of the BK/W wires. Connect the other terminal of the door lamps to the R wire supplying +5V.
Some games have separate power supply outputs for the coin door lamps. If you choose to use these outputs, make sure you connect both terminals of each lamp to the terminals on the power supply.
1-9
Installation
Connecting the Control Wires Connect the joystick or whirly-gig harness and the button harnesses to the JAMMA harness using crimp splices or butt soldering, according to the information in Tables 1-3 and 1-4.
Installing the Optional Volume Switch(es) If you want to install an easily accessible digital volume control, the Off the Wall game PCB provides pins near its edge for this purpose. You can install either a momentary center-off toggle switch or two pushbutton switches (for volume up and volume down) in an accessible area such as the coin door opening. See page 5-5 in this manual for the wiring diagrams of both types of switches, These switches will control the volume during the attract and game play modes.
Grounding the Cabinet Find the ground lead (green) of the 115V input power line. Connect this lead in daisy-chain fashion to a bare metal part of the coin door, the control panel, the video display, and the power supply. This AC ground must be of #18 AWG wire or larger.
Checking the JAMMA Connections Before plugging in the game PCB, turn on the power to the game, and check +5 Volts on pins 3, 4, C, and D of the JAMMA connector; +12 Volts on pins F and 6; and -5 Volts on pins E and 5. Check that the video display and the attraction lamp have power. Now turn off the power to the game.
Installing the Off the Wall
Game PCB
- After you have checked the power on the JAMMA connector (above), install the Off the Wall game board set in the cabinet. Use the nylon standoffs and four #6 x 1/2” large screws in the kit.
- Connect the JAMMA connector to the PCB,
- Secure the JAMMA harness away from the PCB with cable ties.
- if you have installed three player stations, plug in the 3rd-player adaptor harness into the connector Off the Wall Universal Kit
labeled JPL3-CR on the Game PCB. This adaptor harness is not keyed, so make sure the wires exit from the PCB — they should not be draped over the board. No components will be damaged, however, if you plug the connector in backwards: the center player controls will just not work.
- Turn on the power to the game. Check that the game PCBs function. If a video picture is not present, see Chapter 3.
Installing the Bezel, Decals,
Labels, and Attraction
Assembly
The bezel, decals, labels, and attraction assembly are shown assembled in a cabinet in Figure 1-1.
Installing the Display Bezel Find the cardboard display bezel in the kit. This bezel can accommodate both 19-inch and 25-inch video displays. Follow the instructions on the back of the bezel, and cut the hole and outside edges as required. if the bezel is missing from your kit, you can use a plain black bezel in the cabinet. Then cut out the game insiructions shown in Figure 1-4, and adhere that label to the bottom center of the bezel.
Installing the Product ID and FCC Label Place the product ID label (part no. 038158-01) and FCC compliance label (part no. 039450-01) on the back of the cabinet.
Installing the Side Panel Decals Find the side panel decals in the kit. Wet the left and right side panels of the cabinet with slightly soapy water, Then position the decals as shown in Figure 1-1. Remove any wrinkles in the artwork using a squeegee. Allow the sides to dry.
Installing the Attraction Assembly
Find the Off the Wall attraction shield and the attraction film in the kit. Using the existing shield as a template, cut the shield and film to size, if necessary. Install them on the cabinet as shown in Figure 1-1.
Setting the Coin and Game Options
Set the coin and game options in the self-test. See Chapter 2 for information about the option settings. If
Start/Action Start/Action or Start/Turbo Center or StartTurbo Off the Wall Universal Kit
A.
ATARI
GAMES Figure 1-4 Hole-Cutting Template for Off the Wall” Kit Control Panel
Installation
i
Installation
you have installed three player stations, you must set the game options screen in the self-test to three playess. Otherwise the software will not recognize the third set of controls.
Maximizing Earnings
For maximum earnings, regularly maintain your Off the Wall game following the instructions in Table 3-1, in Chapter 3, When you set up the game and when you collect money, perform the automated self-test and check the controls with the Controls Test in the self-test.
Game Play
This section describes the theme of the Off the Wall game and the game play features.
Introduction
Off the Wall™ is a fun new game with a universal appeal. It’s easy to play, difficult to master, and a real test of reflex and quickness. Players try to keep a ricocheting ball in play while hitting and destroying blocks that protect the goal.
Play Mode Off the Wall is a simultaneous game including a joinin-anytime feature. It’s even expandable to three players just by making a change in self-test and adding another set of controls and harness. The object of the game is to keep one ball in play by ricocheting it off the walls and bricks of the playfield. Bricks are destroyed by hitting them with the ball. Eliminating bricks exposes the exit/goal a little more each time. White-colored bricks are indestructible and cannot be destroyed. The player who puts the ball in the exit scores a bonus for each remaining brick on the playfield.
1-12 Off the Wall Universal Kit
Each player begins the game with three balls. When all balls are exhausted, the game is over. At the beginning of the game, each player launches a ball into the playfield. As long as one ball remains active on the playfield, no one will score a lost ball. Any new ball lost within four seconds of being launched will not result in a lost ball. After a short period, a single ball on the playfield will split in two and double the action! Player controls consist of a whirly-gig and Action button. The whirly-gig controls the direction of a paddle along the player's wall. Pressing the Action button allows for very fast movement of the paddle along the wall. Glowing white bricks release Special Powers when hit with a ball. The power will drift towards the player who last hit the ball. If the ball is moving fast and furiously, the Special Powers will move in various ditections before being captured.
Special Powers
- Extra Ball—an extra life ¢ Catch Ball_the ability to catch, then release the ball
- Invinci-ballthe ball destroys all bricks in its path
- Bigger Paddle—a larger hitting surface
- Slow Ball—slows down the speed of the ball ° Firepower—shooting feature Off the Wall has over 50 waves of variety! Each wave has a different arrangement of bricks on the playfield. A few of these include rotating/moving bricks, regenerating bricks, moving exits, etc. Every four rounds is a Sudden Death Round. This feature is only in multi-player games. One ball is launched and players duel it out to see who is the last survivor.
1-13 Figure 1-5 Instructions Label for Monitor Bezel HOW TO PLAY > Hit glowing bricks to release power-ups.
to advance. Ball Paddle
>» Each player has 3 balls
per game. > To put spin on ball, hit
ball with moving paddle. L) Ball
© Fateh S Slow Ball LY Ball Invinci- -- Firea _ / Power > Press Turbo Button to make paddle move faster. <
NOTE
If you do not have the Off the Wall™ monitor bezel, cut out this game instruction label and adhere it to the bottom center of the monitor bezel. | If you instail whirly-gig controls, be sure to black out the last line of this label, since it no longer applies. Use a permanent black marker or black tape. If you install joystick controls, do not alter this label. Off the Wail Universal Kit Installation
Off the Wall Universal Kit
NOTES
1-14
CHAPTER 2
Self-Test
‘RODU
Use the Off the Wall” self-test to check the
condition of the game circuitry and controls.
You will see the self-test information on the
video display and hear the sound test infor-
mation through. the speakers. You do not
need any additional equipment to perform
the self-test. & You should perform the self-
test when you first set up the game, each
time you collect the money, or when you sus-
pect game failure. ¢ This chapter shows the
screens in the self-test and explains each of
the tests. The screens and explanations are
arranged in the order they appear in the self-
test. Table 2-1 lists all of the self-test screens
and their purposes.
Self-Test
Entering and Exiting the Quick Self-Test
To enter the quick self-test, hold down any button on the control panel and turn on the game power switch. ‘This summary screen shows all the statistics, the controls test, whether joysticks or whirly-gigs are installed, and the volume adjustment band. These items are described in more detail later in this chapter.
L JANA START STARTITURBO. Button 2 Button 3 Off the Wall Universal Kit
QUICK SELF TEST Statistics Idle minutes 4 Player Mins 2 Player Mins 2 Player Mins 1 Player Mins © Player Mins
R Player Mins
Error Count
Controls Test Pregs.buttons and move controls c YAMMA START START/TURBO. Button 2. Button 3. Audio Volume R JANA START. ‘STARTITURBO. Button 2 Button 3
TECPLELEELELELLLEL
Adjust Volume while pressing LEFT START EXIT: press 2 START buttons
Figure 2-1 Quick Self-Test Screen This quick self-test screen stays on until 60 seconds after you last press a button or move a control. Then the true. attract mode appears. You can also press two start buttons to exit this quick self-test.
Screen Use or Purpose
Select Test Use to select from the full list of available self-test screens.
Adjust Volume Statistics Statistics Display Histogram Dispiay Game Options Displays the game statistics. Display a horizontal bar graph of game times. Use to set and check the game options settings. Displays the game sound level adjustment.
Coin Options Use to set and check the coin options settings. Sound Board Test Use to check the audio circuits and the coin switches. Controls Test Use to test the control panel switches and joysticks or whirly-gigs. RAM Tests Video RAM (looping) Use to check the video RAM. Color RAM (looping) Use to check the color RAM. All RAM (looping) Use to check all RAM. ROM Test Use to check the program ROMs.
Playfield Stamp Test Use to check ihe alphanumeric and graphic displays, Motion Object Test Use to test the movement and color of game objects. Monitor Tests Color Test Purity Test Red Color Purity Green Color Purity Blue Color Purity White Color Purity Grey Color Purity Convergence Test White Convergence Violet Convergence Green Convergence Use to check the video display color circuits.
Use to check the red color purity in the video display. Use to check the green color purity in the video display. Use to check the blue color purity in the video dispiay. Use to check the white color in the video display. Use to check the grey color in the video display.
Use to check and adjust video display convergence of red, blue, and green. Use to check and adjust video display convergence of red to blue. Use to check and adjust video display convergence of red and blue to green.
Table 2-1 Summary of All Self-Test Screens
2-2
Off the Wall Universal Kit
Entering and Exiting
the Self-Test
To enter the complete self-test, turn on the self-test switch on the game PCB. Exit the self-test by switching off the self-test switch.
Select Test Menu
Choose which test or screen you want to see from this menu, shown in Figure 2-2. Move up and down the list by moving the left control; the corresponding test is highlighted in white. Choose the screen by pressing either left-player start button. Pressing the right start button also lets you advance to the next item in the list.
Adjust Volume
This game has digital volume control — not a potentiometer. The screen has 32 grey vertical bars that become filled with green as you increase volume, To raise the volume, move the left control. To forget any changes, push the right start button. To save this setting and return to the test menu, press the left start button, An average volume level is when the left half of the bars is filled with green.
SELECT TEST then ptess START button
ADJUST VOLUME STATISTICS GAME OPTIONS COIN OPTIONS SOUND BOARD TEST CONTROLS TEST RAM TESTS ROM TEST PLAYFIELD STAMP TEST MOTION OBJECT TEST MONITOR TESTS
Figure 2-2 Select Test Screen Self-Test
Statistics
Statistics Display Use the information shown on the statistics screen, in Figure 2-3, and on the histogram screens to keep track of your game use and maximize your profits. Record the information on the Off the Wall statistics page in the back of this manual. The statistics are collected from the last time the statistics were cleared. Follow the instructions at the bottom of the screen to clear the statistic or to exit from this screen and go to the histogram. ° Left Coins show the number of coins counted in the left coin mechanism.
- Right Coins show the number of coins counted in the right coin mechanism.
- Aux Coins shows the number of coins counted on the auxiliary service coin inputs.
Left Coins Right Coins Aux Coins New games ‘Continues Total Games Sessions idle minutes. 4 Player Mins 2 Player Mins 3 Player Ming L Player Mins C Player Mins R Player Ming Error Count Total Coins ‘Avg Time/Coin. p secs
To clear statistics press RIGHT START button
For next screen press LEFT START button
Figure 2-3 Statistics Screen
Self-Test Off the Wall Universal Kit
Option Settings
| Restore Factory Options | Yes | Now | Lets you set all the game options to the factory options or lets you |
use your own settings. Make sure you set this to “no” to use your own chosen settings.
| Game Difficulty | Easy | Moderate W | Starting ball speed and maximum ball speed determine the game |
| Hard | Very Hard | difficulty. |
Number of Players Allowed Twow Three Lets you set the software to correspond with how many player stations are installed on the control panel.
| Music in Attract (Mode) | Yes | No |
Lets you turn the sound on or off in the attract mode. Note that if set to “On”, the music only turns on for about 30 seconds every 10 minutes—not constantly.
| Clear High Score Table | Yes | Now |
Lets you clear the high score tabie. Auto High-Score-Table Reset Yes ¥ No Automatically resets the high scores to the factory defaults after 2000 games, unless any players have entered their initials within the previous 200 games. V Manufacturers recommended settings. These settings are shown in green on the screen,
Table 2-2 Game Option Settings
- New Games is the number of games played before continuation. © Continues is the number of games played during *add-a-coin” (continuation).
- Total Games is the number of games played (one game per player).
- Sessions is the number of sessions played. For example, one 2-player game counts as One session.
- Idle Mins shows the number of minutes the game was not being played.
- 1-Player/2-Player/3-Player Mins are the number of minutes the game was played by one player alone, two players simultaneously, or three players simultaneously, © Left/Center/Right Player Mins are the number of min- utes the game was played at the left, center Cif installed), and right player stations.
- Error Count shows the number of errors counted in the erasable memory. If you have an error count, the statistics may be wrong. If you consistently have errors counted for several weeks, replace the EEROM at 19L on the game PCB. © Avg Time/Coin is the average number of seconds played per coin. Press the left start button to see the histogram screen, Histogram Display The histogram (horizontal bar graph) screen is shown in Figure 2-4; it displays the game times in seconds. Use it to keep track of your game use and to maximize your profits. The red highlighted time span is the median value (the midpoint), meaning half the games were below this value and half were above. Follow the instructions at the bottom of the screen to clear the histogram or to exit from this screen and return to the select test screen.
GAME TIMES.
600 & up
To clear histogran move control and press RIGHT START button,
Figure 2-4 Histogram Screen
Off the Wall Universal Kit Self-Test
| Option | Settings | Explanation | |
| Free Play | Now | Yes | Set this to “Yes" for demonstrating the game. |
| Discount to Continue | Now | Yes | Lets you offer a reduced price per credit when players want to |
continue a game.
| Game Cost | 1 coin 1 credit v | Sets the number of coins required for one credit. |
- coins 1 credit
8 coins 1 credit
Bonus for Quantity Buy-in Nonew
2 coins give 1 (extra coin)
9 coins give 3 (extra coins) Lets you choose various levels of bonus coins or no bonus.
| Right Mech Vaiue | 1 coin counts as 1 coinw” | Is the number of coins each coin counts as in the right coin |
a mechanism. 1 coin counts as 8 coins
| Left Mech Value | 1 coin counts as | 1coinW | _Is the number of coins each coin counts as in the left coin |
1 coin counts as 8 coins mechanism,
v Manufacturer's recommended settings. These settings are shown in green on the screen.
Table 2-3 Coin Option Settings
Game Options
Check and select the coin options on this screen, shown in Figure 2-5. To move through the options, move the left control. Change the option highlighted in blue. The factory default settings are shown in green. To change a setting, move the control. Follow the instructions at the bottom of the screen to restore the original settings or save revised settings. Press the left start button to exit.
GAME OPTIONS
RESTORE FACTORY OPTIONS NO DIFFICULTY LEVEL MODERATE NUMBER OF PLAYERS ALLOWED TWO Music IN ATTRACT YES CLEAR HIGH SCORE TABLE ON AUTO HIGH SCORE TABLE RESET ON
To restore original setting press RIGHT START button To SAVE this setting and EXIT, press LEFT START button
Figure 2-5 Game Options Screen The game option settings with factory defaults are shown in Table 2-2,
Coin Options
Check and select the coin options on this screen, shown in Figure 2-6.
To move through the options, move the left control. Change the option highlighted in blue. The factory default settings are shown in green. To change a setting, move the right control. Follow the instructions at the
COIN OPTIONS FREE PLAY: No DISCOUNT TO CONTINUE: NO GAME COST: 1 COIN 1 CREDIT: BONUS FOR QUANTITY BUY-IN: NONE RIGHT MECH VALUE: 1 COIN COUNTS AS 1 COIN LEFT MECH VALUE: 1 COIN COUNTS AS 1 COIN
To restore original setting press RIGHT START bution To SAVE this setting and EX! press LEFT START button
Figure 2-6 Coin Options Screen
Self-Test
bottom of the screen to restore the original settings or save revised settings. Press the left start button to exit. The coin option settings and factory defaults are explained in Table 2-3.
Sound Board Test
The sound board test indicates the condition of the sound effects circuit on the JSA Audio I PCB. You can also test the coin switches in this screen. This test appears in Figure 2-7. Press any two start buttons to return to the select test menu.
Controls Test
The controls test screen is shown in Figure 2-8, You can test all the control panel switches and joysticks or whirly-gigs. If you have joysticks, your display will look like the left screen in Figure 2-8. As you press each button, the grey switch name changes to white. The joystick switch markers (small grey asterisks) move in the same direction as the joystick. A red ERROR message means two opposing switches are simultaneously activated. If the asterisks do not appear correctly or you see the ERROR message, check the connections, switches, and joystick control. If you have whirly-gigs instead of joysticks, your display will look like the right screen in Figure 2-8. As you turn the whirly-gig clockwise, the “raw” reading should increase and the “delta” reading should be a positive number. As you turn it counter-clockwise, the raw reading should decrease and the delta reading should be a negative number. Simultaneously press two start buttons to return to the select test screen, When you first enter self-test the joy-
Press buttons.and move controls. c JAMMA START STARTTURBO, Button 2 Button 3 JAMMA START. STARTTURBO. Button 2 Button 3. JAMMA: START: STARTTURBO. Button.2 Buttons
- £ :
JOYSTICKS
To return to menu press 2 START buttons Off the Wall Universal Kit
SOUND BOARD TEST
NUMBER OF SOUNDS SOUND. CPU STATUS
‘COIN MECH SWITCHES: LEFT. RIGHT: 0 To return.to. menu press 2 START Buttons
Figure 2-7 Sound Board Test Screen
sticks control screen will be displayed. Whirly-gigs are detected automatically when they are used.
RAM Tests
Use this selection screen, shown in Figure 2-9, to choose which RAM test you want to perform. Use the different tests according to Table 2-4. if you have serious RAM problems, you may see only a colored sereen, Press the left start button (and hold it, if the test is looping) to leave the individual RAM test and return to the Select RAM Test screen. Press the left start button once more to return to the select test screen.
ROM Test
The ROM test screen is shown in Figure 2-10. The checksum information appears. If the game has no ROM errors, you see the message ALL ROMS are OK.
Press buttons’ and move controls. Cc JAMMA START START/TURBO Button 2 Button. 3 JAMMA-START START/TURBO. Button 2 Button 3 JAMMA START STARTITURBO Button 2 Button 3
Delta Raw Delta Raw Delta. Raw Q 60 0 cs 9 56
WHIRLY-GIGS
To return to menu press 2 START buttons
Figure 2-8 Controls Joysticks/Whirly-Gigs) Test Screen
2-6
Off the Wall Universal Kit
Location of Problem eof Test RAMs Tested
Playfield is erratic or Video RAM 7K, 9K looks wrong, motion objects are not working properly, or game play is erratic or game is locked up.
Colors look wrong. Color RAM 3E, 6E
Table 2-4 When to Run the RAM Tests
SELECT RAM TEST
then press left START button
Video RAM (looping) Color RAM (looping) All RAM (re-start) Exit RAM tests
To stop a LOOPING test press and HOLD the LEFT START button until results are displayed
Figure 2-9 RAM Tests Menu
ROM TEST Location Checksum Location . Checksum 17E (OH) 7756 17J (OL) DS5A0
ALL ROMS are OK
To return to menu press LEFT START Button
Figure 2-10 ROM Test Screen
If the game does have ROM errors, the location of the bad ROM(s) will be displayed. Note: the OS (operating system) and program dates in your game will be dif- Jerent from those shown in Figure 2-10. Press the left start button again to return to the select test screen. Self-Test
Playfield Stamp Test
This test, shown in Figure 2-11, checks the condition of the playfield graphics ROMs in the game. Scroll through the stamps with the left control. If you see an error on the screen or large numbers of stamps missing, this indicates an error with the playfield ROMs located at 14P, 18P, 14S, 18S. Press the left start button to go to the select test screen.
Motion Object Test
‘This test, shown in Figure 2-12, checks the tansparency, movement, and color of various objects in the game. Select the test function with the right start button. Use the joystick or whirly-gig to move objects, change pictures, change object size, change object palette, and toggle the horizontal flip. If there is an error, check the motion object ROMs at 14P, 18P, 14M, and 18M. Simultaneously press any two start buttons to go to the select test screen.
Monitor Tests
These tests indicate the accuracy of three types of monitor adjustments. You select the test from the monitor test selection menu.
Color Test
This test shows the dynamic range of the video display color circuit. The screen is shown in Figure 2-13. The screen should be four bands (black/white, red, green, and blue from top to bottom), each with a color scale from dark to bright, left to right. If the screen
= 8 mD sc7 5 ¢ # mo M wee ROHS m =
o ' wt t cect tvea er renee ty
Figure 2-11 Playfield Stamp Test Screen
Self-Test
‘Motion Object Te Select menu item with RIGHT START button then use contro!
To return to menu
Press 2 START Buttons
Figure 2-13 Color Test Screen
does not match this description, adjust the video display as described in the video display manual. Pressing the left start button causes 32 or 64 steps for each color band. to be displayed. In addition, pressing the right start button causes the white border to be turned on or off, Return to the select monitor test screen by pressing any two start buttons,
Color Purity Test The color purity test has five screens. Each screen is a solid rectangle of color. The first screen is red. The Off the Wall Universal Kit
other screens, which you can see by pressing the right start button, are green, blue, white, and grey. These screens show the adjustment of the color purity of the video display. Each screen should display a rectangle of color, with no curving at the corners, no unevenness of color, and no lines in the display. If the screens are not correct, adjust the video display as described in the video display manual. Return to the select monitor test screen by pressing the feft start button.
Convergence Test The convergence test has three screens: first white, then violet, and finally green. The white screen is shown in Figure 2-14. To see the violet and green screens, press the right start button. Press the left start button to go to the select monitor test screen.
{> Convergence Test
‘To change colors press RIGHT START Button To return to menu press LEFT.START Button
Figure 2-14 Convergence Test Screen
Check the following on the screens: « The grid lines should be straight within 3 mm, and the lines should not piricushion or barrel.
- The convergence of the lines on the violet and white screens should be within 2 mm. If these screens do not meet these criteria, adjust the video display as described in the video display manual. Return to the select monitor test screen by pressing the left start button.
CHAPTER 3
Troubleshooting
and Maintenance
INTRODUCTIO!
This chapter contains troubleshooting tables
and repair procedures for your Off the Wall”
game. The chapter has two parts. The first
part contains three troubleshooting tables.
The tables contain general troubleshooting
information, the voltage levels and test points
on the printed-circuit boards, and a list of
ROM-caused problems, with specific ROMs to
check and replace. # The last part of the
chapter has information about connecting the
video display (if it requires separate positive
sync) and repair information for the joystick
and. whirly-gig controls.
Troubleshooting and Maintenance Off the Wall Universal Kit
Problem uggested Action Coin Mechanism Problem
- Check the wiring to the coin switch and counter.
- Test the ccin switch with the sound test screen in the self-test.
Game Play Problem . Check the harness and connectors. . Perform the seif-test. . Check the voltage levels on the PCB. See Table 3-2, Voltage Inputs and Test Points. . Check What ROM Problems Look Like, Table 3-3, for specific ROM problems. kona
Joystick/Whirly-Gig Problems 1, Has the joystick been lubricated? If not, lubricate it at the location shown in Figure 4-2
- Check the harnesses and connectors.
- Check the switches on the joystick or the encoder pot on the whirly-gig control by using the Controls Test in the self-test procedure.
- If you took the control apart, have you reassembled it correctly?
- Make sure all the parts on the control are in good repair. Repair or replace parts.
Sound Problem 1, Is the speaker volume turned up? (Volume is adjusted digitally in the self-test.)
- Check the voltage on the game PCB edge connector.
- Check the wiring from the PCB to the speaker.
- Check the voltage level to the PCB. See Table 3-2, Voltage Inputs and Test Points.
- Replace the speaker.
Video Display Problem Screen is dark. 1, Is the game plugged in?
- \s the game turned on?
- Are the connections good?
- Is the line fuse good?
- Is the display brightness turned up?
- Are the solder connections on the line filter and transforrner good?
- Is the game PCB edge connecter tightly connected?
- Check all of the items below. If you answer no to any question, you have a problem with the video display, not with the game circuitry. See your video display service manual. a. Do you have power to the video display? b. Are the video display’s filaments lit? c. Do you have high voltage to the video display?
- Are the voltage levels to the video display PCB correct? (Power voltage is 100 VAC or 110 VAC, depending on the type of video display. Video signal voltage is 0.5 to 3.5 Volts.) 10.If the level is not correct, check the connectors and the harness.
Only a colored screen appears. You probably have a serious RAM problem. Display area wavers or is too small.
- Do you have correct power voltage to the video display PCB?
- Do you have correct high voltage to the video display? Picture is wavy.
- \s the monitor ground connected to the monitor?
- Are the sync inputs connected properly? Picture is upside down. When you serviced the display, you connected the wires incorrectly. Switch the horizontai or vertical yoke wires on the display. Convergence, purity or color problems. Use the screens in the self-test to adjust the video display. Use the adjustment procedures in your video display manual. Picture is not centered Use the centering procedures in your video display manual.
Table 3-1 Troubleshooting Table
Off the Wall Universal Kit
Voltage Test Point or LED
+5 + 0.25 VDC +5V1 Source and Purpose Troubleshooting and Maintenance
Logic power from the switching power supply. CRS5 LED (Game PCB) open. Lights when 5 V is appiied to the PCB and the reset (RST) jumper is
CR9 LED (JSA Audio If PCB) Lights when the +12V supply is good, CR3 LED (JSA Audio lil PCB) Lights when the -5 V supply is good,
Table 3-2 Voltage Inputs and Test Points on the PCBs
Problem ROM Causing the Problem Check the ROM at:
Program works, but motion objects or Graphics ROMs playfield is wrang. High: 18M, 18P, 18S (Game PCB) Low: 14M, 14P, 14S (Game PCB) Garbage on screen; program doesn’t work. Processor 13F (Game PCB) Game program is erratic. Program ROMs High: 17E. Low: 17J (Game PCB) No sound or erratic sound Audio Program 12C (USA Audio !il PCB)
Table 3-3. What ROM Problems Look Like
Video Display Sync
Problems
This game board provides separate positive horizontal and vertical syne on a separate connector, for monitors that will not work with the composite negative sync signal provided at the JAMMA edge connector. This connector (labeled “Sync”) is located near the edge connector. Pin 1 is horizontal syne, Pin 2 is vertical sync, and Pin 3 is ground.
Troubleshooting
The tables in this chapter (3-1, 3-2, and 3-3) can help you troubleshoot problems in your game. The troubleshooting table lists possible sources of problems in various parts of the game. The voltage inputs and test points can help you troubleshoot PCB problems: The ROM problems table can help determine exactly which ROM might be causing game play problems.
Removing and Replacing the Whirly-Gig Control
Removing and Replacing the Joystick Control
The joystick control is shown in Figure 4-2. If you want to repair the joystick control, disassemble it by removing it from the control panel. To repair the joystick, disassemble it by removing the retaining ring at the bottom of the shaft. To replace any of the four switches, remove the two screws that secure each switch.
The whirly-gig (encoder pot) control is shown in Figure 4-3. If you want to repair the whirly-gig control, disassemble it by removing the flanged knob from the control panel. Then remove the fastening hardware. To repair the whirly-gig, dis~ assemble it by removing the split lock washer, nut, and washer from the top of the plate.
ROMs and RAMs
If you have think you have bad ROMs or RAMs, perform the ROM test in the self-test. If you have a ROM problem, see Table 3-3.
Troubleshooting and Maintenance Off the Wall Universal Kit
CHAPTER 4
Parts lustrat
NTRODU ION
This chapter provides information you need
to order replacement parts for your kit. Com-
mon hardware parts, such as screws, nuts,
washers, and so on, are included in these
parts illustrations. When you order parts, give
the part number, part name, the number of
this manual, and the serial number of your
game. With this information, we can fill
your order rapidly and correctly. We hope
this will create less downtime and more prof-
it from your games. Atari Games Customer
Service phone numbers are listed on the
inside front cover of this manual.
Parts Ilustrations Off the Wall Universal Kit
049749-01 > Items Not Shown ‘Attraction Fiim| ‘A046501-01 a7205-01) VAMUIA Hames Assy. Attection Shield | Off The Wall Universal
| 049747-01 | © | Kit installation Instructions |
Bezel WiGraphics| ss 141026-001 a Spit Ferrite Bead 178032-002 Cable Tie
: . Coat | 049750.01
: | | Side Panel Decal
/A049753-02 4 Off The Wall
| ai | (J | =. | ==> | | PCB Assy. |
tie ¢ fs = (Winiriy-Gig Vorsion)
| é | i | = | s | /A049753-01 |
: ff The Wall : ve PCB Assy.
| Red Deca! | cs | (oystick Version) |
g - 178265-001
| Q | = | a | LSiylo Nylon |
ee : Standoff Green Decal : paces) 160044-001 i #6 x 1/2 Scrow
| ‘Snap-Action Switch | : | (4 places) |
(4 places for 2-player| 6 places for S-player) 178237-001
| Red Button ASsy.| | Bue pe | = |
(2 places) cat - z
| 178283-012| | _178237-006! | my |
| START/TURBO| | Green Button | i |
Indicator Plate ‘Assy. 2 (Joystick Version)| (2 places) (4 or6 places) | y74997-002 8-Way, Short Throw Gold Contacts, Blk Knob 75-5112B Wico Joystick 410-24 x 3/4"
| (2013 places) | 178237-005 | Carriage Bolt |
| 049751-01) | Bye Button Assy. | (Bor 12 places) |
| Ctl Panel Decal | (places) | 17028-0040 |
#10-24 Nut- 047209-01 Washer Assy. Ctl Panel Gover} —- A049722-01 (8 or 12 places)
| 049751-01, | Whirly-Gig | 175014-1040 |
Ctl Pane! Decal (Encoder Pot Assy.) | #10 Flat Washor ed (@ 0r3 places) (8 oF 12 places) [Decal
(049743-01 Ctl Panel’ Instructions Label Je
178237-001 Red Button Assy. (2 places) 178289-008 STARTACTION Indicator Plate (40r6 piaces) | 178297-005 Blue Button Assy. (2 places)
178283.008 START/ACTION —| Indicator Plate (Whitly-Gig Version) (406 places)
Figure 4-1 Parts for Off the Wall Universal Kit with Whirly-Gig Controls (4049752-02 D) and with Joystick Controls (4049752-01 D)
Off the Wall Universal Kit
Base Assy. W/Gold Switch
TR-HAASIES w6x1" Tapping Screw “160044-007; Snap-Switch Ta-Hnas12s #4 x 3/4 Pana Tapping Screw
e— — _|99-080026 12" Washer
‘99-080049 Top Plate
175614-1061 Stee! Washer
‘99-080030 Compression Spring
99080047 icroswitch Actuator
| 99-0s0043 | gie* Retaining Ring Parts Illustrations
99-980048 ~] Black Joystick Assy.
Figure 4-2 Wico 8-Way Short-Throw Joystick Assembly 171097-002
Parts Illustrations Off the Wall Universal Kit
178157-002 Flanged Knob
75-5112B #10-24 x 3/4” Carriage Bolt (4 places)
049724-01 Encoder Pot Adapter Plate 175014-1040 #10 Flat Washer (4 places)
177026-0040 #10-24 Nut-Washer Assy. (4 places)
138009-001 Optical Encoder Pot (600EN-128-CBL Clarostat)
Red - +5V. Orange - CLK
Figure 4-3 Whirly-Gig (Encoder Pot) Assembly A049722-01 A
4-4
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Parts Ilustrations
4-6 Off the Wall Universal Kit
am 0 eg ie] [by s3a3 8 ava
ous = as oor Dp eo] oO.
Figure 4-5 JSA AMMA Stand-alone Audio) Ii PCB Assembly A048974-07 A
CHAPTER 5
chematic
This chapter contains the schematic diagrams
for your Off the Wall” game PCB and audio
PCB. The game PCB and JSA Audio III PCB
assembly drawings are illustrated in Chapter
4, Parts Illustrations.
Schematic Diagrams
com> ror) cow) ron cD cone? ney oom > cc-Locnt> CSPRRL* > Cue > ‘CRED? cave? vio on cSELFTEsT> cco) cstaRTe> CUPLAD Jere cooaLa> currnad eRIGHTLAD CLBUTTON > CLpurTONe > CLBUTTONI> cuerna> cRIGHTLBD coo? coo?
sme 1 o—aHsmc.ouT 2 os ustac aut 30 —oe cons com> reer 250) c-993 cota) key CooNTRRD €C=LOCKR? CSreai-) ‘¢RuD OND? ‘CCREEN} came) cseRvICeD ernur come? cSTARTRD ‘CUPRA cOOmNRAD CLEFTRAD cRiouTAAD cReurToN > CRBUTTONE > saees-AA O———— ACTA CROUTTONS) Jae#-B8 0 acTE? CLEFTRBD JARWR-CC O———# /SERVICER, RIGHTRS) sNeH-D0 O- 70) con
sean pce. = f2a0er ont a cure cont-ce et __§ sans -sye tft a ing SY Off the Wall Universal Kit
Off the Wall Universal Kit
Th Ja lw” Ta T 1 ia «00
AP —o #8 wae OS ee +f fee |-O FB ae 5% ayo © Fé ae © OS ve
i 3 mr ORG mar OR ae
sseRvICE, ssenvictz «| — ‘ssEevICE3 | SERVICES
SeLFTEST & Schematic Diagrams
smacR
Wo osc 2 o———seerma 1 ore 10 O————#RT3 ‘303 8 os 7 oor 6 o——esrare, 30-———=coner 3 + eenvices 30———$ecor-c 20-0 {ooo
Bo yo 439 O———+ cr 12 oer Abo erry 10 0———=RT¥ Ore 80+ 7 ou $6 o0———esrars 53 0——«coIna § o——+ senvices 30 ———scaenr-k 20———s-0 o_o
Figure 5-1 Off the Wall Game PCB Assembly Schematic Diagram. 049726-01 B
5-3
Schematic Diagrams Off the Wall Universal Kit
sw 20 ssettde | a
| scree | s0 | 2 | ||
| pares | aa aye Be | Z | ||
| rere | By | 7 owe | vere | noc |
| rein | Ron | ‘aren | ||
| Pinte» | FN | ors | ‘score | |
| erate | By | 3 | TSB ES scons | |
| sre | 3 | wooe—He | TebEa nttn | ||
| Steva | a8 | Sele Feb a ysiarus |
fate—Hle Tab SES vous Tae ow
| ad | 1 | ins |
asi neo & aioe is woz ara 470 eo She vegttoonr i i
| cree | : | 0 | Hl | so 4g BO, | |
| aot | Sen | HS | ue | 3 tens] | |
| paki | EIETETA | z= ayLt 92 | (or | bali) | |
| scree | 7 | eT | i | uk | |
| rane | rrcieres | S28 | ot | usu | |
| t | i | meee | art | ||
| sue | t | 1 | an | His ls oo | t01 |
| Lepeabewcew ten beslewlen * | TEST | ssvsmes |
SEPP cc estes CEE EET...
oPT/sH uo tro § Ara 7a ara & We F ora Fare F ove mace |
| vee | - | saa 58 | ca |
| ie | al | rad wv | |
| one | E : | eT | me |
| : | | | H | 1 |
| cee | t — | a aa oh | ——H8 : |
tis + ies t TsesT
axe meee mes are 7
| woot | se | He, | |
| ve} | ik | ae | En |
| uF | cus | 28 | |
| we | i | pea we tT] | oe es Li |
| bie | mage ak | 32 | |
| me | - | feos |
Leys Les Lew Lose Leys Les Lote. TSF PEPPER PP Ly pe ow
| eid er | To DIRS & CLK3 | + |
| VERT 98 | To DIR2 & CLK2 | . |
ver a] @7, 20 DIRI &CLKI ;
| wv |voRE PUP | To DIRO & CLKO | —t | = |
| wo | |e |e] | me |
z zo— 20-4?
| soo] | 3 | 3 | 3 |
| To DIRS & CLK3 | = | —{}—_1 | |
war a) e710 DIR2 & CLK2 . : veri] @/_TODIR1&cLKi jf = mu | wor ez) _@f To DIRO & CLKO . 7a [won #4 | .
5-4
Off the Wall Universal Kit Schematic Diagrams
w mo gr Fit0 ase & HSTNC.OUT
| ow | 1,70 | J |
roy Ch oa ae
| i. | Toe | os | |
| wen | toe | T | sinc ou |
Boor fa oo
sinus e184 reels, as ssehes 2H ro wy 2207
Stestetija ar} 06 180-2 £28 = 1 0s
vruorrae—2 fia TEST
+ ip red ae satus fe 1K ras
| Shwe | wes | aces | Ea |
a parc
| 2 | ot 20 | | | Maamy | _Rovcowe ttle |
7 Gace a
| 30 | cat | cersue | Sian | ay] |
¢ teow Zhi oo Ft TSe5T
UP o——j1| VUP
GND o——3| VDN
VON 2) GN
Two optional momentary Optional ‘SPDT. momentary push-button switches action-switch
Figure 5-1 Off the Wall Game PCB Assembly Schematic Diagram 049726-01 B
Schematic Diagrams Off the Wall Universal Kit
Le yalit aor hone Can 4 Sime tes ns i peste
GND AND AGND TIED INTERNALLY NEAR MSM6295
yw a
This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.
Schematic Di Off the Wall Universal Kit
mas FeDID : aa Roca ris6 lass
- "Zeows eet so ie [EE pats nee
a718K =
& seen ‘* Spd SOCKET SRREERRLZARAPARVEZ Ey
a
a S888) nine BB Bel
usra a our arm tor, Lsa78 LaaTS CaaS Bo! oy
Su at vee as Bd vag 2M ter . 51916 poseens| JB wor z0K6 | less "a eas Bee Bae fs a
| a | , | me |
| Ea | I | fat |
reer a ca me ¢ ’ eee a iy
| goes | orev | les wor | |
| ord | me | mt | |
| Sei BS | FE | sR | |
| wae § | sl | s 8 | |
| URTRES | RESET As. | by | As 3] |
| TH: | a Ae | be] | Re ne |
| Ww | D mo | ba | | Aa. o1| |
| tT | De | ne De |
st oF
wa oo
Off the Wall Universal Kit Schematic Diagrams
a 34 its suse 34a dP wr foete{s Sol Soc fect ott Ste Seti sett iota oe ; toot, pte sire ied ah RESET
wre Gh Sie She ome moe Ba am fore—Z/m foe — Ores mooie ee ee Soe SLs oe SE wre users ow ua RESET
4s ey ae oh? 1 e asyaK 2[, PF ls sib abe axime—2pox opt tex] usr wer_|usra =
2c moo cc 18 os Ste yor $0 TRE 16 70, AE eoxiies 15 10s ORS 141700 Sa Rone 1703 FE 32 1702 [= row no Pew SEREERES
Figure 5-2 JSA Audio II Assembly Schematic Diagram 048973-01 C
Schematic Diagrams Off the Wall Universal Kit
= ome He Ti t roe i
- C4 xo __| serxer Titer pe wer dase tin ate
m Me wee
Off the Wall Universal Kit Schematic Diagrams
sore titan Soares soso
Figure 5-2 JSA Audio Ill Assembly Schematic Diagram 048973-01 C
5-11
Schematic Diagrams Off the Wall Universal Kit
A ATARI GAMES
Off the Wall’ Statistics Sheet
Date Recorded: Location:
Meter:
Statistics Screen
Left Coins: Right Coins: Auxiliary Coins: New Games:
Continues: Total Games:
Sessions: Idle Minutes: 1-Player Minutes: 2-Player Minutes: 3-Player Minutes: Left-Player Minutes: Center-Player Minutes: Right-Player Minutes: Error Count: Total Coins: PEP Average Time/Coin: sec.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Atari Games Corporation 675 Sycamore Drive
P.O. Box 361110