After Burner Service Manual (420-5842-01 1st Printing)
After Burner (Sega, 1987) · Manual · 18 pages · 8 sections · original scan
1ST PRINTING-OT Bo ee Ro Ko He Ro Ro Ro Ko Ho te Ro Rr Hr Ho Ho He Hoh Ko Ko Hr Ho Ho Hohe Hohe Ko Mo SH HSB
SEGA
If RN SERVICE MANUAL oS Modo H HHH HHHB
SEGA ENTERPRISES,LTD. EER RRP WD WP WP GP PP WP PPP PPP WP GP GOP AP GP GO AP GP GD AP HP GP GP HP GP PAP GP GP AP GP GDP BP GP GO AP BO
ey Ke Re Ko Ko Ko Ko Ko Ko Ko Ko Ho Hp Hp Ko Ho SoSH FH op Ko Ho Ko Hoo HoH Ho Ho Ho Ho Ho HoH
BRPPPPRPERPREPP PEPE PEER PE EPERERERPREESE MANUAL NO. 420-5842-01
-— TABLE OF CONTENTS
SELF-TEST
VALUE SETTING FOR EACH TYPE
TROUBLE SHOOTING
- TEST OPERATION .-eeeccesceceeeceeeeereeee te eeeeees
- TEST ITEMS & DESCRIPTION ..---++--+++-+---+
- MEMORY TEST eoseeceecectceeeeteeeneeeses
- INPUT TEST -0-ccceceecceereeteesereeteeeseee
- OUTPUT TEST v-eceeeceeceeetessteeeeeseneneees
(A) MOTOR TEST oeeeccecesecscceeeesettreeiee
- SOUND TEST -eeceeececeeeeeeeteereeeeeees
- CRT TEST -o-ceeeeceeeteecessseteeseteneceneeeees
- DIP SWITCH ASSIGNMENTS .«.-----+------+-+
- BOOKKEEPING -eseeseceeesseeeeeseteeeeeeeee
- BACK UP RAM CLEAR ooeteeecerees
- LIMIT SWITCH AND VOLUME (V.R.) «---
- INITIAL FAILURE --e-eeeeeereeee eee cere renee eee n eee
- THE CABINET DOES NOT MOVE PROPERLY §
SELF - TEST
This test mainly checks the operation of game PCB’s, discovers defects if any, and also checks monitor colors and audio quality. In addition, the test indicates dip SW assignment and has a Bookkeeping function.
TEST PROGRAM
a) (2)
(3) (4)
(5)
(6) (2) (8) (9) Memory Test : Checks the EPROM programs and RAM Area. Input Test : Tests the operation of COIN, VULCAN, MISSILE, START, SERVICE switches, ete. Output Test : Tests the operation of each lamp. Motor Test : Checks the operation of the motor and the limit switches, and indicates rolling/pitching VOLUME (V. R. ) values. Sound Test : Checks the quality of the synthesized sound transmitted from the PCB. CRT Test : Checks colors displayed. Dip Switch Assignment : Indicates dip switch assignments. Bookkeeping : Indicates data on average score and play time. Backup RAM Clear : Clears Bookkeeping memory.
- TEST OPERATION
- Push the TEST SW button to display the test menu (Fig. 1).
- Move the handle upward or downward
| wos | . | and bring the arrow to the desired |
DIAGNOSTIC VER. 2.00 = INDIVIDUAL position. Press the TEST SW button MEMORY TEST again to display the desired test. INPUT TEST SUPE UT TEE (3) When each test is finished, press
| MOTOR | TEST | the TEST SW button again to display |
| ili | itl | the test menu (Fig. 1). |
Cc R TY TEST . pip $¥aTcR asst OnMENTS To end the test program, bring the BOOKKEEPING arrow to EXIT and push the TEST BACKUP RAM CLEAR SW button. EXIT SuLueT KY STICK! PUSI TEST BUTTONS
FIG. 1
»* INDIVIDUAL and CONTINUE can be selected by pushing the START button when the arrow is at the top position.
INDIVIDUAL : Indicates only the item which the arrow points to. Push the TEST SW button again to display the test menu (Fig. 1).
CONTINUE : After displaying the item which the arrow points to, push the test SW button again to proceed to the following test in the order as indicated in the Fig. 1 test menu.
2, TEST ITEMS AND DESCRIPTION
- Memory Test Checks the game PCB’s 4 main ROMs,
ee BS SS 8S 7 18 RAMs and 5 CUSTOM IC’s. PIAGNOSILC VER. 2. 09 MEMORY TEST ** ROMS TEST ** GOOD means the IC is in “GOOD” cD ic. $8 GOOD D foto} oc re. 68 GooD operating condition. 4* RAMS TEST #* 22 GooD 1c. $1 GOOD Ic. 38 GOOD 23 GOOD Ic, 32 Good 1c. $9 GOOD BE goop rc. §¢ gocn ie bee seen If there exists any malfunctioning of the 32 GOOD 1,134 GOOD iC. 150 Goop IC’s, “BAD” will be indicated. 33 GOOD 1c. 135 GOOD 1c, 151 GOOD custom 1c TEST 30 GOOD 1c, 37 GOOD Ic, 53 GOOD 97 GOOD Ic, 108 GOOD
- INPUT TEST @ Operate each switch. When the “OFF” condition is changed to “ON”, the DIAGNOSTIC VER, 2. 00 corresponding switch is in good working INPUT TEST order.
COIN #1 Of © START oF as Date values should increase when the handle yen, OF ouar one it is moved to the left, and indicate 80H
COIN #2 orn SERVICE OFF grip is moved to the right, decrease when
STICK RIGHT LEFT Bar when released. STICK UP DOWN 30H ae ae SPEED a0H @® Date values should increase when the handle grip is moved upward, decrease when it is moved downward, and indicate 801 when released.
® Date value should increase when the throttle lever is moved forward, decrease when it is moved backward, and indicate 80H when released.
- OUTPUT TEST Each lamp will flash if it is working properly.
DIAGNOSTIC VER. oureutT
- START LAMP.
- WARNING LAMP
- MOTOR TEST (DELUXE, COMMANDER TYPE)
The cabinet can be moved by operating the handle while pulling the handle grip trigger. The motor speed can be changed to 5 levels by pressing the START SW button.
® Indication of motor speed.
® Date values should increase when the cabinet is (// moved to the right, decrease when it is moved to motor TEST the left, and indicate 80H when it is at the center position. MOTOR POWER ore HOMER. DEVEL: to 5 Ol -® Data values should increase when the cabinet is
| woTOR Posi T10N | ep’ --~} | moved upward, decrease when it is moved | |
| uP, | » DOWN | FR | downward, and indicate 80H when it is at the |
| LIMIT SW | grr. 9 | 09 | center position. |
0 (However, if the dip switches are set to “MOVING STD,” the data values will not be indicated.)
RECA Sy @ Indicates limit switch operation. (However, if the dip switches are set to “MOVING STD,” only the right and left ones are indicated.)
- SOUND TEST
DIAGNOSTIC TEST VBR, 2. 00
SOUND TEST
= 1. MAIN MUSIC
2, SUB MUSIC
- BXPROSION
a
3.
1 BURNER
SELECT 8Y STICK
PUSH START BUTTON -!
- C.R.T, TEST
DIAGNOSTIC VER. 2. 00
GR. T. TRST CLEAR
COLOR BAR
| = Red | | >
i} reen
Blue
'
k ® Push the handle upward/downward to move the arrow accordingly. Bring the arrow to the desired item and press the START bution.
The selected test item has various sounds to be selected. Bring the arrow to the desired sound item, press the START button, and the sound will be produced.
Bring the arrow to EXIT and press the START button to return to the initial display.
Cheeks the C. R. T. position. Make sure that the on-screen corners are consistent, and then make size adjustments,
RGB color check. (The color becomes darker from the left to the right.)
Each color has 8 levels of brightness
Brightness from white to black
- DIP SWITCH ASSIGNMENTS
DIAGNOSTIC
Dip switci 1 od os ok ob of ot off DIPSW. A OFF OFF OFF OFF OFF ORF OFF OFF a DiPSW, GB OFF OFF OFF OFF OFF OFF OFF OFF VER, 2
ASSIGNMENTS = 00
TOTAL TIME 15H 2
PUSH START BUTTO 8M L1S——
Not +A 1234 COLIN SWHL 1 COIN 1 CREDIT. ® .A $678 COIN SWH2 1 COIN { cREDIT
| -BoL2 | CABINET TYP® | MOVING Dx] © | |
| .BO3 | SLOTLE LEVER | with | ® |
sb SHIPS PER CREDIT 38uLPS———7y
| .BOS | SHIP INCREASE | YES ————_—_ © | |
| +B 6 | CONTINUE GA | ES | @ |
. B18 GAME DIFELCULTY NORMAL ae ©
- Bookkeeping
DIAGNOSTIC YER. 2. 00 oO BOOKKEEPING COIN CHUTE #1 8 — ® coms cuure we —| _@ COIN CREDITS Mai SERVICE CREDITS 5127 —- -— © TOTAL CREDITS 5888 ——__} __ © | —® Present setting of each dip switch
Coin switch setting
Cabinet type
Inclusion of throttle lever
Number of player’s planes per credit
Awarding player’s additional plane(s)
To continue game or not Game difficulty
Operation frequency of coin chute 1
Operation frequency of coin chute 2
Number of coin credits
Usage frequency of service switch
Number of credits in total
Total working time (OO H ©O M OO 8)
Press the START button to display the following :
DIAGNOSTIC VER, 2. BOOK KEEPING
NUMBER OF GAME AVE, SCORE TOP-SCORE LCW-SCORE
** GAME TOTAL AVERAGE LONGEST
PUSH START BUTTON TIME * felis OOHOOM! oa ®
® 2037 ® rae 29456 | —-® b4g2h ®
. _-® ge leek Total number of game plays
All players’ average score
Highest score
Lowest score
Total game play time
Average game play time
Longest game play time
- BACK UP RAM CLEAR
Bookkeeping data is stored for at least 3 days after the power is turned off. When clearing, bring the arrow to YES and push the TEST button.
DIAGNOSTIC VER. 2, 00
BACKUP RAM CLEAR
No
~ YES
SELECT BY STICK
PUSH TEST BUTTON !
- LIMIT SWITCH AND VOLUME (V.R.) VALUE SETTINGS
The limit switch and volume (V.R.) value settings are as follows :
DELUXE | COMMANDER } UPRIGHT
HANDLE, left Under 25H | Under 25H | Under 35H a
| HANDLE, right | Over DBH | Over DBH | Over CBH |
al HANDLE, upward Under 40H | Under 40H | Under 40H
| HANDLE, downward | Over BBH | Over BBH | Over BBH | |
| LIMIT, left | Over 40H | Over 40H | — |
| LIMIT, right | Under COH | Under COH | — | |
| LIMIT, upward | Over 20H | — | ——_ |
| LIMIT, downward | Under BOH | — | — |
TROUBLE SHOOTING
bad
3.
4, INITIAL FAULT
The cabinet does not move properly :
- Refer to “THE CABINET DOES NOT MOVE PROPERLY.”
On-screen trouble exists :
- Nothing appears on the screen :
%* On-screen images become whitish :
- The on-screen picture is disfigured.
Sound is irregular :
- Volume is low.
%* The connector is loose.
- No sound can be heard.
Credit is not registering properly :
- IC board dip switch setting is
wrong :
- Connectors are loose : Check the monitor’s power supply (FUSE 100 V 5A).
Check the monitor’s signal connectors and cables.
Replace the IC board.
Make adjustment to the desired volume.
Check the connectors of the power
amplifier, IC board, speaker, etc.
The power amplifier or the IC board is defective and should be replaced.
Set it in the TEST MODE (DIP SW).
Check the Coin Chute Tower connector.
- Coin chute micro SW is damaged :
- Complete failure to register :
- Game dose not start :
%* Connector connection is wrong :
- The START SW is damaged : Check the switch function in the TEST MODE (INPUT TEST). If damaged, replace the switch.
The IC board is defective and should
be replaced.
Check the control panel connectors.
Check the switch operation in the TEST MODE (INPUT TEST ).
If damaged, replace it.
yy THE CABINET DOES NOT MOVE PROPERLY
(DELUXE AND COMMANDER TYPES)
2.
3. Slow movement.
- Input voltage decreases :
%* One of the Triacs on the Triac
board is damaged : = Make sure that the power supply is separated from that of the other machine.
=> Replace the defective one.
(After a certain working time has elapsed, the gearbox teeth face becomes fully accustomed to the operation and causes the movements to become faster, but this is not irregular.)
Insufficient movement.
%* Limit switch working position > deviation :
- Handle unit VOLUME (V. R. ) 2 deviation :
- The handle’s working angular > width is small :
Sound is heard when the cabinet moves.
»* When the cabinet moves, =>
a friction sound is heard :
%* When the cabinet moves, 2
a rattling sound is heard :
%* When the cabinet moves, >
a clattering sound is heard : Check and make adjustment in the TEST MODE ( MOTOR TEST).
Check and make adjustment in the TEST MODE (INPUT TEST).
Check and make adjustment in the TEST MODE (INPUT TEST).
The protector which is attached to the edge of the step or cover is entangled. Open the cover and properly reattach it.
The gearbox may be damaged. Replace it or the motor unit.
This results from the motor unit’s motor
deviating from its axis’ proper position with the gearbox rotation axis center. Make the necessary adjustments,
- When the cabinet rapidly makes => The motor unit tire is slipping. Add reverse turns, a creaking sound spacers if the spring which presses the is heard : tire is weak. If the tire is worn out, replace it.
4, Awkward movements :
- The motor brushes are worn out : => Replace them.
- The motor is burnt out : = Replace the motor or motor unit.
- The gearbox is damaged : = Replace the gearbox or motor unit.
- Does not warm up properly.
- Deviation in the limit switch => Check and make adjustment in the working position ; TEST MODE (MOTOR TEST).
- Limit switch damage : => Check it in the TEST MODE (MOTOR TEST) and if it is damaged, replace it.
- VOLUME (V.R.) variation : => Make sure that the volume value is 80 H.
- VOLUME is damaged : => Check the VOLUME function in the TEST MODE and if it is damaged, replace it.
- The drive wheel slips : => The motor unit tire slips when making reverse turns. Add spacers if the spring which presses against the tire is weak. Also, if the tire is worn out, replace it.
- Warming up is properly done but the cabinet does not move during game play.
- Handle VOLUME deviation :
- Handle VOLUME damage :
- Suddenly becomes immovable.
- The mat switch is working :
- Fail-safe software is functioning :
- The breaker functions :
- The Triac is damaged :
- VOLUME (the cabinet or the handle) deviation : => Make sure in the TEST MODE CINPUT TEST) that the VOLUME value is 80H.
Check in the TEST MODE (INPUT TEST) and if damaged, replace it.
When stepping or putting items on it, the mat switch functions and the
cabinet will not move. Make sure that
nothing is put on it. (See “Mat Switch”.)
Turn off the power and then put it
back on again. (See “Fail—safe”.)
Check if the breaker is functioning. If it is, then push the breaker to reset. When it functions often, the Triac may be damaged. (See “Breaker’s working conditions”.)
Replace the Triac board or the triac. (See “Concerning the Triac”.)
Check in the TEST MODE (INPUT TEST, MOTOR TEST J and make adjustment.
- Totally immovable.
The drive board connectors are loose
- Motor connectors are loose
- The breaker is functioning : Check the connectors.
Check the connectors, (When the power is turned ON without the motor connector connection, the breaker may function.)
Reset the breaker.
Cheek in the TEST MODE [ DIP SW J
- DIP SW mode is not properly set and set to “MOVING DX.”
Breaker’s working conditions.
Each of the 8A breakers attached to the AC unit is in series with the corresponding DC motor and it functions due to overcurrent when the motor is subjected to overload or damage. The functioning characteristics (at the normal environmental temperature) in relation to the overcurrent energized period are : 16A/5 second, 32A/1 second and 80A/0.1 second. When resetting the breaker, make sure that the reason which caused the breaker to function has been eliminated.
Concerning the Triac
In these types of machines, the DC motor is subjected to an all— wave rectified control by 2 Triacs. When only one of the two is damaged and its circuit is open, the DC motor will be under a half—wave rectified control. This results in insufficient power for the motor, causing the cabinet movement to become slow. In this case, it is difficult for the breaker to function and the Triac’s damage can hardly be noticed. Therefore, care should be taken as concerns this point.
- Checking the Triac
TRIAC Turn the power off and check for the
YA, presence of conductivity between T1
o and T2 out of the 3 Triac pins by using
a tester. If conductivity is present, then the Triac is damaged.
1 DANGER! Be sure to turn the power vi off before performing the Triac check. T2 G
- MAT SW
When the mat which is put on the floor within the cradle hoop is subjected to a certain amount of load (as when putting the feet on lightly), the switch is actuated causing the cabinet to return to stop. The cabinet starts to move again when the load is removed.
- = Fail—safe
In the case where the cabinet does not move for a certain period of time (approximately 1.5 second), even though the electric current is running through the motor, (judging from the angular detecting VOLUME), the Fail—safe function shuts off the current to the motor in order to protect it by determining that the motor is being subjected to an abnormal load. Therefore, the cabinet does not move when the Fail—safe works. The Fail—safe will stop functioning and clear when the game ends.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
SEGA ENTERPRISES, LTD. No. 2—12, Haneda 1—chome Ohta-ku, Tokyo 144, Japan OTel. : (03) 743 — 7438 OFAX: (03) 743 — 5539
OTLX : J22357 SEGASTAR
© SEGA 1987
Printed in Japan