CATHODE RAY TOMES

Atari 2600 Field Service Manual

Atari 2600 (Atari, 1977) · Service Manual · 159 pages · 74 sections · original scan

Page 1

2600/2600 A

VCS DOMESTIC (MAN) Field Service

Manual

FD100133 ® ATARI 1

Page 2

E.C.R. NO. 0021 = ATARI, INC. Consumer Product Services 845 W. Maude Avenue Sunnyvale, CA 94041

ENGINEERING CHANGE REQUEST

Latest ® DATE REQUESTER PART NO. REV. ATARI 1 rrr] Cormneanons Comoe 1-21-83 S. Doyle FD100133 02 PART TITLE 2600/2600A VCS DOMESTIC FSM REASON FOR CHANGE REQUEST:

Error in Flowcharts and Parts Lists

DESCRIPTION OF CHANGE:

Replace cover page with new (Rev. 02) cover page.

Retain this ECN as a record of these changes.

PARTS DISPOSITION:

(SEE pescespriow )

Replace pages 4-25, 6-21, 8-3 and 8-7 with the attached corrected pages.

ENGINEERING CHANGE REQUESTER— PLEASE COMPLETE ABOVE DOTTED LINE

REASON FOR CHANGE OENIAL OR COMMENTS:

£C.R. BECOMES AN €E.C.N. ENGINEERING CHANGE NOTICE WHEN SIGNATURES AND E.C.N. NO. ARE PRESENT THIS E.C.N. NO. 0021

Page 3

ATARI

VIDEO COMPUTER SYSTEMIM

FIELD SERVICE MANUAL

MODEL 2600/2600A DOMESTIC (M/N)

Page 4

Atari believes that the information described in this manual is accurate and reliable, and much care has been taken in its preparation. However, no responsibility, financial or otherwise, shall be accepted for any consequences arising out of the use of this material. Information contained herein is subject to change. Revisions may be issued to advise of such changes and/or additions.

Correspondence regarding this document should be forwarded to Manager of Technica! Support, Consumer Product Service, Atari, Incorporated, 845 W. Maude Sunnyvale, California 94086.

2600/2600A Domestic VCS

Page 5

Table of Contents

Section Title F

INTRODUCTION S

1 THEORY OF OPERATION Introduction Overview Game Console Outer Casting Switchboard Motherboard 2600A Model Differences - All Revisions 2600A Model Differences - Revisions 14 and 15 2600A Model Differences - Revisions 16 and up Summary fl NDDUEFUNNE EE

2 SCHEMATICS AND SILKSCREENS 2-1

3 TESTING AND TROUBLESHOOTING 3 Equipment Requirements 3. Test Procedures and Methods 3-: 2600 Model Modifications 3 2600A Model Modifications 3 Testing with the Diagnostic Test Cartridge 3. (Version 2.6) Initialization 3-7 RAM Test 3-8 Color Bar Test 3-9 Gray Bar Test 3-1 Diagnostic Matrix Test 3-11 Audio Tones Test 3-13 Paddle Control Lines Test 3-14

4 2600 DIAGNOSTIC FLOWCHART 4-1

5 SYMPTOM CHECKLIST 5-1 2600 Symptom Checklist 5-2 2600A Symptom Checklist 5-5

6 2600A DIAGNOSTIC FLOWCHART a i

7 GAME CONTROLLERS Overview Joystick (X-Y) Controller Joystick (X-Y) Controller Check Paddle Controller Paddle Controller Check Driving Controller Driving Controller Check Keyboard Controller Keyboard Controller Check 8 ATARI CX2600 (M/N) PARTS LIST ATARI CX2600A (M/N) PARTS LIST (lee Ome) ° go NN NNN NTS We FONDUE WE EE

iii 2600/2600A Domestic VCS

Page 6

Table of Contents

Section Title Page

9 SERVICE BULLETINS 9-1

List of Illustrations

Figure Title Page

1-1 2600 Functional Diagram 1 1-2 2600 Game Console - 1-3 2600 Switchboard and Motherboard Assembly 1-3 1-4 TV Switchbox 1-4 1-5 2600A Game Console 1-5 1-6 2600A Board Layout 1-6

2-1 2600/2600A IC Pinouts 2-3 2-2 2600 Motherboard Silkscreen 2-4 2-3 2600 Channel 3 Switchboard Silkscreen 2-6 2-4 2600 Channel 3 Switchboard Schematic 2-7 2-5 2600 Channel 2-3 Switchboard Silkscreen 2-8 2-6 2600 Channel 2-3 Switchboard Schematic 2-9 2-7 2600A Motherboard Silkscreen (Revs. 1-13) 2-10 2-8 2600A Motherboard Silkscreen (Revs. 14 and 15) 2-11 2-9 2600A Motherboard Silkscreen (Revs. 16 and up) 2-12

Inserted in Front Pocket of Notebook:

2600 Motherboard Schematic 2600A Motherboard Schematic (Revs. 1-13) 2600A Motherboard Schematic (Revs. 14 and 15) 2600A Motherboard Schematic (Revs. 16 and up)

3-1 2600 Trigger Circuitry with Static Modification 3-3 3-2 2600 Static Modification Zener Diode 3-4 3-3 Location of Colored Dot Over Trace 3-4 3-4 2600 Switchboard Static Modification 3-5 3-5 2600A (Revs. 1-13) Static Modifications 3-6 3-6 Switch Initialization Positions 3-7 3-7 Defective RAM Patterns 3-8 3-8 Color Bars Screen 3-9 3-9 Gray Bars Screen 3-10 3-10 Diagnostic Matrix Screen (Shorting Plugs OUT) 3-11 3-11 Diagnostic Matrix Screen (Shorting Plugs IN) 3-12 3-12 Audio Tone Test Screens 3-13

iv 2600/2600A Domestic VCS

Page 7

List of Uustrations (Continued)

F Cy

Figure Title

Switch Initialization Positions Color Bars Screen Defective RAM Patterns Gray Bars Screen Defective Gray Bars Screen

Diagnostic Matrix Screen (Shorting Plugs OUT) Diagnostic Matrix Screen (Shorting Plugs IN)

Diagnostic Matrix Screen with Defective Pattern Audio Tone Test Screens RC Waveforms STC Address Line Waveforms STC Data Line Waveforms FrrfrrrperSee REF OONDWEUNE Neo FrrrrrrrrrERe FEE FFE EUWUUY AREWNKBDOKWNAY

Joystick (X-Y) Controller Joystick (X-Y) Schematic Paddle Controller Paddle Controller Schematic Driving Controller Driving Controller Schematic Keyboard Controller Keyboard Wiring Diagram Keyboard Schematic YEP PSPS, WONDUEWN Pye ppp, WODEUDUVENE

List of Tables

Title Page

Connected Pins on VCS Motherboard 4-47

v 2600/2600A Domestic VCS

Page 8

INTRODUCTION

The Video Computer system™ (VCS) Field Service Manual is organized in nine

sections:

e THEORY _OF OPERATION - overview of how the VCS works and what the basic assemblies look like.

e SILKSCREENS AND SCHEMATICS - electrical drawings and layouts of the

printed circuit boards.

e TESTING AND TROUBLESHOOTING - overview of the procedures for testing and repairing the VCS unit.

e 2600 DIAGNOSTIC FLOWCHART - thorough flowchart enabling the technician to test and troubleshoot a defective 2600 unit.

e SYMPTOM CHECKLIST - for the experienced technician, a list of the high failure parts and the flowchart entry point for that particular problem.

ry 2600A_ DIAGNOSTIC FLOWCHART - thorough flowchart enabling the technician to test and troubleshoot a defective 2600A unit.

e GAME CONTROLLERS - overview of hand controller construction with electrical schematics and recommended test and repair procedures.

e PARTS LIST - detailed breakdown of all parts used in both the 2600 and . 2600A. e

e SERVICE BULLETINS - section to be used to hold service bulletins released

by the Manager of Technical Support. These bulletins will include changes in recommended repair procedures and required modifications for units in the field.

The manual is designed for use by both experienced and inexperienced service personnel. The Diagnostic Flowcharts (Sections 4 and 6) provide detailed diagnostic and repair procedures for technicians who are not yet completely familiar with the VCS. The Symptom Checklist (Section 5) provides a fast repair reference for the more experienced technician.

vii 2600/2600A Domestic VCS

Page 9

SECTION 1

THEORY OF OPERATION

INTRODUCTION

There are currently four types of ATARI Video Computer Systems. The original model (2600) is composed of two PC Boards connected by a 12-pin ribbon cable with the motherboard surrounded by a heavy aluminum casting.

The other models (2600A: Revisions 1-13, Revisions 14-15, and Revisions 16 and up) are composed of a single board with a light aluminum shield. The single board models differ slightly in the video output circuitry. Component differences are:

e Revisions 1-13 have no diodes on TIA lines LM! and Sync. e Revisions 14-15 have diodes and pull-up resistors on TIA lines LM1 and Sync. e Revisions 16 and up include the above mentioned diodes and resistors as well as a timer chip.

The revision level is etched directly on the PC board.

OVERVIEW

The ATARI Video Computer System (VCS) Models 2600/2600A are state-of-the-art microcomputers. They receive instructions for the operation of different games from individual Read-Only-Memory game cartridges and interpret data from the players’ hand-held controllers. They also allow game players to select both a specific version of each game and the player difficulty (on a per player basis). Figure 1-1 is a block diagram of the functional flow of the VCS Model 2600. Section 7 describes the player controllers.

Q wae vac Figure 1-1. 2600 Functional Diagram

Page 10

GAME CONSOLE

The VCS game console is composed of an outercasting that houses the switchboard and the RF radiation shielded motherboard.

Outer Casting

The casting consists of three pieces of plastic (see Figure 1-2). The pieces include the base, which holds the switchboard and motherboard assembly; the top; and the bezel.

Figure 1-2. 2600 Game Console

Page 11

Switchboard

The switchboard assembly holds the player option switches, the power supply, and the RF modulator (See Figure 1-3).

e PLAYER OPTION SWITCHES 5 Switches S101 thru S104 are double-pole, single-throw. Switches S105 and $106 are double-pole, double-throw. All switches are connected between the switchboard and the motherboard by 12-conductor flexible ribbon cable.

e POWER SUPPLY The power supply is composed of a +5 voltage regulator, filter capacitors, and the power on/off switch. Unregulated DC is supplied to the board from the battery eliminator. A supply of +5 volts is routed through a filter circuit to the RF modulator. The motherboard also receives its power (+5 volts Vcc) from the switchboard via the same 12-conductor ribbon cable referenced above.

e RF MODULATOR The RF modulator. converts the signal received from the Television Interface Adaptor chip on the motherboard to a frequency that a television can receive and interpret. Data between the RF module and the Television Interface Adaptor chip is passed via the 12-conductor ribbon cable which connects the motherboard to the switchboard. A coaxial cable passes this signal from the RF module to the switch box mounted on the back of the television.

Figure 1-3. 2600 Switchboard and Motherboard Assembly

Page 12

Motherboard

The motherboard is composed of a PC board containing a microprocessor (MPU) chip, a combination Random Access Memory - Input/Output (RAM-I/O) chip, and a Television Interface Adaptor (TIA) chip (see Figure 1-3). The board also contains numerous capacitors, resistors, transistors, and other assorted electronic components. These parts are all listed in Section 8, PARTS LIST.

MICROPROCESSOR CHIP The heart of the VCS is the 6507 microprocessor chip (MPU). This device makes decisions for the VCS based upon information it receives from the game cartridge and the RAM-I/O (discussed in the next paragraph).

RANDOM ACCESS MEMORY-INPUT/OUTPUT CHIP Temporary storage of data from the WPU is provided by the 6532 Random Access Memory-Input/Output (RAM-I/O) chip. This chip also scans the option switches and the joystick I/O lines for information and maintains time accounting for the MPU.

TELEVISION INTERFACE ADAPTOR CHIP This ATARI proprietary chip generates audio and video signals which are required by the RF modulator. The Television Interface Adaptor (TIA) chip also contains the analog-to-digital converter circuitry that allows the MPU to understand signals originating in the hand-held paddle controllers.

TIA outputs are processed by additional circuitry into a composite video, sound, and color signal which is routed to the RF module on the switchboard via the 12-conductor ribbon cable. The RF module converts the composite signal to a RF signal acceptable to the television. A coaxial cable transmits this RF signal from the console to a selection box that can be mounted on the T.V. This switchbox (Figure 1-4) allows you to display either a signal received by the antenna (for normal T.V. viewing) or a signal from the VCS (for playing a game).

Figure 1-4. TV Switchbox

Page 13

2600A MODEL DIFFERENCES - ALL REVISIONS

The major difference between the newer single board VCS (2600A) and the original VCS (2600) is that all of the components formerly on the switchboard are now located on the motherboard (See Figure 1-5). This includes the player control function switches (Power ON/OFF, COLOR/BW, GAME SELECT and GAME RESET), RF modulator and power supply circuitry. The single board design eliminates the need for the ribbon cable, which connected the switchboard to the motherboard on the 2600 vcs.

Gone, too, are the luminescence and RF output buffers and the two TIA input buffers, all of which were contained in chip A203. In the oscillator circuit, one of the transistors and its associated network has been eliminated and R227-R230 (paddle control lines) are no longer present. C239, going to pin 7 on J202 and J203, has been replaced by C236 and C237 (See Figure 1-6).

Figure 1-5. 2600A Game Console

Page 14

Up mL lisa J aol] GlgeteU"

ig i Bes is > (2ax] R227 C238 ‘Z200MF 16v oft A202 Se = = ~~. Hee Coke 3 ‘ae gos P, 3 Siie} Be A200 acca G0 aw agiigi g BSE ed as a | gage ab88 © 3 (elF 2/18) RF MOO

Figure 1-6. 2600A Board Layout (Revs 1-1 3)

In addition to the component changes, the physical location of several parts has also been changed. Instead of having the right and left difficulty switches placed on top of the game, they are located at the rear of the console next to the game controller plugs. The channel selector switch is also located at the rear of the console. The game cartridge socket is no longer angled, but is mounted vertically on the board.

2600A MODEL DIFFERENCES - REVISIONS 14 AND 15

Revisions 14 and 15 contain the model differences described above, and in addition have new components on the TIA lines, LMI and Sync. There are two 1N914 diodes to prevent feedback on the lines and two additional pull-up resistors to insure the signal is at +5v. To compensate for any signal loss, R215 and 217 have been changed to 47K (R215) and 24K (R217).

2600A MODEL DIFFERENCES - REVISIONS 16 AND UP

Revisions 16 and up contain the model differences described above; they also include a timer chip (A205) added to the reset circuitry of the MPU chip. This chip eliminates the problem of power-on reset failures.

Page 15

SUMMARY

The VCS is a microcomputer that receives its operational instructions from game cartridges, the game console, and player controllers. The 2600 switchboard and motherboard assemblies are housed within an outer casting and are the principle assemblies addressed in the remainder of this manual. The boards are connected by a 12-conductor ribbon cable which passes not only power, but also data between the two boards.

Three chips of the motherboard allow for the interaction between the game and the player. These chips are the microprocessor (MPU), the Random Access Memory- Input/Output (RAM I/O), and the Television Interface Adapter (TIA) chips.

The 2600A model differs primarily in the location of the components formerly located on the switchboard. They are attached directly to the motherboard and eliminate the need for the switchboard and the ribbon cable. The 2600A Revisions 14 and up include even further additional components to improve the performance of the output circuitry.

Page 16

SECTION 2

SILKSCREENS AND SCHEMATICS

On the following pages are representative silkscreens and switchboard schematics for the ATARI Video Computer System. The motherboard schematics for all 2600/2600A VCS _ models are located in the pocket at the front of this binder. Minor variations in design may be encountered depending on the production date of the game, but these schematics provide all details required for an in-depth understanding of all 2600 units, including the various 2600A model revisions..

Page 17

NOTES

Page 18

eo)

VOLTAGE REGULATOR (Top View) UU In gnd out peed aa a-8-1-2- 2-1 -F-2-t-8-2 0-2

D

Tousvudowocuououuoue

E-EataE-E- Bee -i-8-8-8-2t—

es

16 9

1 8

5-pin version (Channel 2 or 3) Pin 1” RF Mod. Pin }

Spin version aT (Channel 2 or 3) Pin } RF Mod. Pin

Cathode C__- Anode NAT. LM340 T.I. 78M05C

A201 and A202 (Top View)

A200 (Top View)

A203 (Top View)

RF Modulator (Top View)

RF Modulator (Top View)

Diode

Figure 2-1. 2600/2600A IC Pinouts

2600/2600A Domestic VCS

Page 19

Figure 2-2. 2600 Motherboard Silkscreen

Page 20

The following variations may appear on the 2600 switchboard:

CHANNEL 3 SWITCHBOARD:

C102 may or may not be in place. C103 and/or C104 may or may not be in place. C103 and/or C104 may be mylar dipped .22 uf. C103 and/or C104 may be ceramic .Oluf (See Figures 2-3 and 2-4).

CHANNEL 2 OR 3 SWITCHBOARD:

The holes on the PC board for the GAME RESET and GAME SELECT switches may not be wide enough apart for the switch legs. To correct this the legs of the switch must be bent in so they fit into the holes (See Figures 2-5 and 2-6).

Page 21

S105.

L102

LIOl RE MODULE

is

  • 101 fe

C10G

Aol

Figure 2-3. 2600 Channel 3 Switchboard Silkscreen

Page 22

ee.

SDA BWISewWog yO09Z/009Z “a-Z eanB1g

DREWAYDs PIBOqUoIIMS ¢ [BUUYD 00ST , |tsvec = EGE Game sevect a S55 RESET + $lo4 DIFFICULTY RT. 7 eae ut + RIO!

  • 293 pirricuLTy LT. { o COLOR/ BW. 4 Ba. 1 so All 2 VOLTAG t WRO 6 Icing reauLaroe! TO, [a+ ON/OFF ro T 224k 3 | GND. } T ] { GNO. 5 o {ch 4 clol .

clo2 clos = ate [OWA Li02 1 L¥Moo,. ] ‘Sut , favo. Lidl HSV 2 ! LRH RE MOD. . MoD, 3 pois

Page 23

1TT C103 AOL sor

Figure 2-5. 2600 Channel 2-3 Switchboard Silkscreen

Page 24

6-2 DIFBWAYIS PIBOguoIMS ¢-Z TEUVEYD 009Z *9-Z aANBIy 1 L+§voc s q ee GAME SELECT S105 a od6 RESET } "1 3 DIFF! RT. 5 29? pireicuty ut. | 4 2? coror/a.w. | se! Alo! POWER iA VOLTAGE de 103. |ReauLaTor 220044. ON/OFF 727A 3 | ano. it | J 6 |GXe. q clo! 1o|GNO. 1 en ald cios! Lee L102 = 4.148} | ne eH. LY Moo. ayo. Lior +5V UMPR. oz CH, SELECT 15a. e se A moo, WIRE on i ia Mop. 4 ce a) Ss = SDA DSPWOQ Y009Z/009Z

Page 25

01-2 (€I-1 “SABY) UBEJDSHTIS PAROqaayZOW YODSZ *Z-Z aaNBIy

SDA B1seWOg y009z/009Z | ate | f co Cr Ji l ta a fl = Boo =)

ceeo c230 J200 PWR COL/ew RES 200 $204 $202 CARTRIDGE SOCKET ASSEMBLY

pa EAE — at A203 AG) § aR elefstalsl) RF MOD APEECEE EE) J

CCI ARQ [eee —1

Page 26

11-2 (G1 pue ny “SAaY) UBaIDSHTIS PIeOGIaYIOY YO09Z “8-2 aaNBry 9 Pin DIFF. L. DIFF. R. 9 Pin 3201 + a 23 3203 ) cass soe “18 § 85 as D,

& oor) 231 C220 cms Coo) u 232 <a

S201 $203 S202 PR pouiew [4 Cartridge Socket Assembly a al SEL RES

L~J CC] ‘L203 AP RR ¥ ao a8 () FAC ECR) A202 aan cus

Gat an i Leet @ EJ

R200 R22i A201 R22 R219 27K | R28 Rz20 R211

RF MODULE 10K 7K 24K 47K R217 | 24K c3oz CTD 10K 47K 3.3K 3.3K

R230 R2I5 ca Cpt) 208 CD rzz2| 13K | C209 G7p1) 215 Q500F) R209 1.8K | Cli,

110K cao Coven) R20| 6.8K | R206

R21 R26 R228 R203 SDA DT1sewWog Y009Z/009Z

Page 27

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 28

SECTION 3

TESTING AND TROUBLESHOOTING

EQUIPMENT REQUIREMENTS

You require eight basic pieces of equipment in order to analyze failures in the 2600/2600A Video Computer Systems (VCS). These items include:

e A 15 MHz oscilloscope

e A Video Computer System switchboard assembly that is known to be operating properly (not required for repairing 2600A units)

e A Video Computer System diagnostic test cartridge, version 2.6 (DTC)

e Two blue controller port shorting plugs for use with the 2.6 (DTC) diagnostic cartridge

e Signal Tracing Cartridge (STC or KLUGE)

e VCS Field Service Manual for Domestic Model 2600/2600A

e Color television set (properly adjusted)

e Frequency Counter

Page 29

TEST PROCEDURES AND METHODS

Atari requires each 2600/2600A model returned for service to be checked for certain conditions. In some instances, a unit must be modified to conform to Atari standards. These changes are summarized below.

2600 MODEL MODIFICATIONS

e Each 2600 mode! opened must be modified as shown in Figure 3-1 to provide additional protection from static discharge.. A Zener diode is connected between the trigger lines and ground, and static strips are placed on the switches on the switchboard (See Figures 3-1, 3-2 and 3-4). These modifications are crucial to prevent component damage due to static discharge.

e Each connector and plug should be checked for a tight, secure fit. Intermittent failures frequently result from a loose connector or plug. e Connectors J202 and J203 should be checked for pushed or broken pins.

e If the unit has a green J200 connector, insert cartridge and wiggle it. If the unit shows intermittent problems, replace J200.

e Each board with Molex chip sockets with insertion aids should have the insertion aids removed and the chip reinserted.

e Check that all components (especially those on the perimeter of the

motherboard) are properly soldered. Check for broken or shorted trace lines. :

e Check for an inductor and capacitor over C201 and R206. Cut the inductor and cap out, being careful not to cut the C201 or R206 leads. e If unit has a standup regulator and heatsink, inspect for hairline fractures between the regulator and switchboard. Also ensure that the regulator is firmly secured to the heatsink by a Tinnerman clip or rivet. e Ensure that motherboards (Rev. 8 or lower) have a colored dot over the trace on the upper-left corner of the board. This prevents shorting the board and the casting (See Figure 3-3).

e Two types of 12-conductor cable assemblies have been used on 2600 model units, the flat-wire type and the ribbon type. When a defect is found in the flat-wire type cable assembly or its male connector on the switchboard, the flat-wire cable assembly should be replaced with the ribbon cable assembly and the 12-pin male switchboard connector should be replaced with the 12-pin female switchboard socket.

Page 30

f| ek

ca202

Figure 3-1. 2600 Trigger Circuitry with Static Modification

Install the static modification on all 2600 units. Install CR202 nd CR203 by removing C236 and C237 and inserting the C236/CR202 and C237/CR203 assemblies in their place (See Figure 3-2). CAUTION: Observe the polarity on CR202 and CR203 (the dark band must be toward the J202/J203 connectors). On the switchboard, install the static strips as shown in Figure 3-4.

Page 31

Cezoz e203 ~ (*c0/41E0 -05)

WRAP LEADS I TURN € SOLOER

Figure 3-2. 2600 Static Modification Zener Diode

echoos

sort | B38

L__$33 Erccseesee

Figure 3-3. Location of Colored Dot Over Trace

Page 32

reyd

) +

a \\

Figure 3-4. 2600 Switchboard Static Modification

Page 33

2600A MODEL MODIFICATIONS

Each 2600A (Revs 1-13) model must have static strips placed on the front panel switches (See Figure 3-5).

Check each connector and plug for a tight, secure fit. Intermittent failures frequently result from a loose connector or plug.

Check that all componenets are properly soldered, and check for broken or shorted trace lines.

If a unit exhibits RF interference that does not clean up using normal adjustment methods, or if a series of lines and bright grid distortions on the screen are accompanied by a loud hum even when properly adjusted, a defective or leaking capacitor may be at fault. Replace C241 (1 microfarad) and/or C242 (.1 microfarad) located respectively between the power jack and voltage regulator.

Mount Static Strips onto Front Panel Switches as shown in this drawing.

Figure 3-5. 2600A (Revs. 1-13) Static Modifications

Page 34

TESTING WITH THE DIAGNOSTIC TEST CARTRIDGE (VERSION 2.6)

The 2600 Diagnostic Test Cartridge (version 2.6 DTC) contains a variety of tests to assist the service technician in identifying the source of problems within the VCS switchboard and motherboard hardware. The test cartridge is used in conjunction with the equipment listed at the beginning of this section. Each test is reviewed in the remainder of this section. Detailed procedures for use of the tests are described in Section 4, 2600 Diagnostic Flowchart, and Section 6, 2600A Diagnostic Flowchart. The tests available in the cartridge ares

RAM Test Color Bar Test Gray Bar Test Diagnostic Matrix Test Audio Tones Test Paddle Control Lines Test

The technician also has a Signal Trace Cartridge (STC or KLUGE) available for tracking motherboard problems that are not repairable with the Diagnostic Test Cartridge.

INITIALIZATION

e Purpose: To prepare the VCS unit for testing by the diagnostic cartridge.

e Format: Connect VCS unit to television and battery eliminator. Set television to proper channel (channel 3). Plug in the 2.6 diagnostic cartridge. Set all 2600 switches to the up position. On the 2600A, set all front panel switches up and rear panel switches to the left (See Figure 3-6).

LaFT «660g GAT Gane Came PONER TVTYPE CFRCULTY orncnty joxce A a

lor we 8 6

initially to the left

Figure 3-6. Switch Initialization Positions

Page 35

RAM TEST

e Purpose: To test the 6532 RAM chip for proper operation.

e Format: On power-up the television displays diagonal lines of some type if the RAM is defective. See Figure 3-7 for examples of screens indicating 2 defective RAM.

NOTE: The absence of defective patterns is no assurance that the entire chip is sound, only the RAM. The operation of the I/O and Timer functions is not verified by this test.

L AAs

  • ~

Figure 3-7. Defective RAM Patterns

Page 36

COLOR BAR TEST

Purpose: To test the 6507 microprocessor, 6532 RAM - I/O chip, and TIA chip for correct operation.

Format: Set all switches to initialization position. A screen of horizontal color bars is displayed (See Figure 3-8). The screen should be steady and unchanging. A gray or blue horizontal reference line runs across the screen about three bars from its bottom. This reference line is thinner than the bars around it. R211 (R213 on the 2600A board) should be adjusted so the bars immediately above and below the reference line are within one shade of each other. Proper operation of the unit is indicated by being able to make this adjustment and by consistent color within the entire span of each bar on the screen. Minor glitches on the edges of the color bars are acceptable. Leave this test on for at least ten seconds in order to catch any intermittent problems, such as a bar momentarily changing colors or blanking out.

NOTE: This figure is a black and white representation of a color television screen.

REFERENCE BAR AME COLOR’

Figure 3-8. Color Bars Screen

Page 37

GRAY BAR TEST

Purpose: To test the function of the luminescence lines (LMO, LMI, LM2) from the TIA chip to the RF Module.

Format: Move the Color/Black & White switch to the Black and White position. There should be eight horizontal gray bars displayed, going from black at the top to white at the bottom in even gradations (See Figure 3-9). The screen should be steady and unchanging. These lines may have minor litches on their edges. A thin white line always appears just over the top black) bar. No color should appear anywhere on the screen. The areas above the top (black) bar and below the bottom (white) bar are of no importance to the test. This test should be left on for at least ten seconds to ensure that there is no "flashing" of any color or shifting of the gray bars.

Figure 3-9. Gray Bars Screen

Page 38

DIAGNOSTIC MATRIX TEST

e Purpose: To test the proper function of the Input-Output ports of the VCS unit.

e Format: Set all switches to the initialized position, then move the Left Difficulty switch to the "B" position. The test is performed in two parts:

lL. With the blue shorting plugs removed, the matrix of nine rectangles on the screen should look like Figure 3-10.

  • The shorting plugs are then inserted and the pattern should look like Figure 3-11.
  • Press the GAME SELECT switch. If the switch is properly functioning, that area of the matrix will black out. Release the GAME SELECT switch and repeat the procedure with the GAME RESET switch.

The Matrix jumps once every second.

T oa Pink 2 not Used abe fois eP21s te " elzlele]e|ele|é a} ee: [2 4 3 6332 4 *

ifafe/afatalafa} ETRE [a] HE a] a] {al [2 Geeen Green aledeledzlteTds 12 Pl oF Green ot] ses elelele]eléfe ]F me

  • fa) 14] |2] ) BIB 4 [err ofa) [ay 2) 2

Green Green . -le : Game Game Game Green ae oe ee ne oe ee ee Reset Select Reset Not Used Ela dele pepe] aye Switch Switch Switch

6932 i

Figure 3-10. Diagnostic Matrix Screen (Shorting Plugs OUT)

Page 39

a. Green = Ws ede New 4 Ho Not Used stete]2]2]2¢]s]¢4 Not Used Ri 3 | not Used fjejelejelelel]a Z|rme fe] = 5 oy 3 3

3 3 z 3 3 E 3 2)43)2)4]2 3 3 3 3 b is a i} EI f FH a 3 F] cies , Geeen 2ye]2]2 7272 [2 de Pink oF Green eeeed elé]elelé]é le fF Not Used

on

3 3 3 s 3] |e] da] a BIEL EH] 4 Ht! 3] fal da] da] 2 ae Green ale lels |-l]eds/s Game Gare Came Green = = = r rr ri s s Remt Select Reset Not Used ele]ilé]élé le ]é sonch Seth Scien T

Figure 3-11. Diagnostic Matrix Screen (Shorting Plugs IN)

2600/2600A Domestic VCS

Page 40

AUDIO TONES TEST

e Purpose: To test the function of the audio tone generation and modulation circuitry.

e Format: The VCS unit should be in the initialized mode. Move the Right Difficulty switch to the "B" position. The test displays two alternating patterns on the screen (as shown in Figure 3-12) while two alternating tones are heard. The tones change in sync with the screen. This test pattern continues for one full cycle after the Right Difficulty switch has been returned to the initialized position.

Figure 3-12. Audio Tone Test Screens

Page 41

PADDLE CONTROL LINES TEST

e Purpose: To test the proper operation of the Paddle Control Lines by viewing the analog waveforms at the analog-to-digital conversion inputs of the TIA chip.

e Format: Pins 37, 38, 39, and 40 of the TIA chip are checked with the oscilloscope with the VCS unit in Diagnostic Matrix mode and with the shorting plugs in place. This test is required only if there is a problem with the hand controller lines. The procedure for this test is detailed in Section 4.

Page 42

SECTION 4

2600 DIAGNOSTIC FLOWCHART

The Diagnostic Flowchart is intended to be easy to use and the primary aid when troubleshooting the 2600. Follow the prompts in the order presented. When a question is asked, follow the line from that box which best applies to the unit's condition. The figures referenced in the flowcharts are located at the end of this section. When a line terminates with a letter inside a circle, note that a page number (i.e., pg. 4-3) is near it. Turn to that page, locate the letter in another circle, and continue the diagnosis. The flowchart leaves nothing to chance, it tells you when to perform a specific test, and when to replace components, and even when and how long to "burnin" the unit. "Burn-in" the unit for at least two hours after completing repairs.

When a problem is extremely difficult to diagnose, the flowchart sends you to the Signal Tracing Cartridge (STC) routine, "D" page 4-47. Due to the repetitive nature of the STC routine, no flowchart is used. Read and follow the instructions as directed. Should the STC procedure fail to isolate the problem, after carefully inspecting the switchboard and motherboard assemblies for shorted and/or open trace lines, and solder bridges swap all three chips (6507, 6532, and TIA). Should the problem still persist, call ATARI, Techline Specialist: Inside California at (800) 672-1466 and Outside California at (800) 538-1535. Be certain to always burn-in the unit for two hours after completing repairs. This helps to ensure that intermittent problems are found and also greatly increases your customer's satisfaction with your repair work.

SWAP OUT PROCEDURES

Many places in the diagnostic flowchart, a box tells you to "swapout" a chip or a number of chips in a particular order. The "swapout" instruction means that you should replace the indicated components one at a time with a known good component of the same type. The VCS should then be tested with the new, known-good component in place to see whether the "swapout" solved the problem being checked. If the swapout did not fix the problem, the known-good component should be left in, and the next component inserted. Once the problem is solved, you then place the suspected bad chips one by one into the system to determine whether or not those you pulled out are truly defective. In this way, you avoid needlessly replacing good components.

CAUTION Extreme care should be taken when handling the integrated circuit chips (A200, A201, A202, A203). They are all very sensitive to static electricity and can easily be damaged by careless handling. Always keep the chips in their plastic carrier tubes or

on conductive foam when not handlin ig them. Make certain you are well grounded

when handling the chips. Atari strongly recommends that you wear a conductive grounding band (which ties from your arm to ground) when handling the chips.

The chips are also susceptible to damage from stress when being removed from or inserted into the sockets. Always use a chip-puller when removing the chips. Do not pry chips out with a screwdriver or any other tool.

Failure to follow the above guidelines results in unusually high chip failure rates and extra expense. ‘

Page 43

2600 Diagnostic Flowchart

No Pg 45 Does any der fective RAM uipicame No warped and ragged Yes paccarry re on left side on screen (see Age) of screen? Py. hs

Yes No

Replace the A202. B ) Ps 3

Does unit now show they No Kreg Tees wait now color bars pattern? 2) A202 bars pattern? ss =z J ves

2600/2600A Domestic VCS

Page 44

2600 Diagnostic Flowchart (Continued)

Are color bars present? (See Figure 4-2). Are color bars properly adjusted? (See Figure 4-2)

screen? (See Figure 4-4, 4-6,4-9).

No No No

r — oe Is any other test ‘Check your No pattern on the switch settings. Are they correct?

Is there "snow" on the screen? (no modulation) Pg. 4-7 Is ANY modulation present on screen? No

Yes

Check VCS connections to TV and channel setting. a Test VCS with known - good battery eliminator.

ee Is "snow" on screen gone? Yes

Pg. 4-9 Pg. 4-5

Pg. 4-6

No

Pg. 4-11

4-3 Pg. 4-2

2600/2600A Domestic VCS

Page 45

Bad Video Troubleshooting

Use swapout procedure to Bad switchboard Pg told identify bad board,

motherboard} Does A203 have No} Repair opentrace, | Yes good Ver (+5v at Does unit now have pin 8) and ground a picture? (at pin 1)?

Yes

Check R238, Is a -5v p-p signal Yes C221, and R233. Present at R236 on Replace as the side toward A203? pe

No

Laapadad Mss} Replace A203. at pin 5 of A203?

No .

Swapout A201.

Does unit now have a test pattern on the TV?

No Pg. 6-2 >. = Check R221, Is it Replace R22) anaes oy i} Yes. OK? (3.3K) ‘the TV?

Yes No

Check that ‘the trace line from A201 pin 2 is not shorted to another line. Pg oe

Isa picture Swapout Isa picture now

now present on = 1) A200 presenton the TV? [J Yes

the TV? 2) A202

D Pg. 45

—<t

A

Pg. 4-2

4-4 . 2600/2600A Domestic VCS

Page 46

Gray Bars Test Procedure

a

e——-

Place color/ black & white switch in B&W position.

Did screen pattern change when switch was moved ?

Yes

rt Is proper gray bar pattern pre nt? (See L Figure 4-4). = Yes

Is a partial segment missing or is any color present? (See Figure 4-5) Pg. 4-7

No Pg. 4-20

Yes Pg. 4-45

2600/2600A Domestic VC

Page 47

Color Bars Test Procedure

Reconnect VCS and initialize.

Are color bars No present on screen?

Yes Pg. 4-2

Adjust R211 so that color is aligned properly. (See Figure 4-2). 1 _i_!

Is VCS tunable Yes to proper shades?

No Pg. 45

Pg. 4-23

Page 48

Defective Switch Troubleshooting Procedure

<2

On 2600 units, use swapuut Bad Switchboard procedure to Pg. 6-38 identify bad board.(See Chart)

Bad Motherboard

With inoperative switch in up position | 1, (open), is +3v present Pg. 3 at 1201 pin for that awitch%See Chart)

Yes

Close the switch Pg. 4-7

Is there an open Repair open trace. Does switch ives |s dv now present between J201 and [Yes now change at the RAM pin No RAM pin? the pattern for that switch? on screen? (See chart) No

Yes c ) pg a7 No

~<e-

Swapout

  • A202
  • A200
  • A201

Yes - Does switch now work?

No Pg. 4-2 CONNECTION CH, G 3201 Pin No. A202 ah enka Black Feet and White . a Left Difficulty 5 7 Right Difficulty zi 16

Select 9 2B

Reset 8 a

4-7 2600/2600A Domestic VC

Page 49

Defective Switch Troubleshooting Procedure (Continued)

Check RAM (A202) pin for Yes the switch for +5v. Is it present? Pg..4-9 No poe be Check for shorted trace line. Repair as necessary.

Does switch now work?

Swapout A202.

a

, Ty. Does switch <3 now work?

No

Check whether capacitor on that RAM ] line is shorted to ground. Replace as necessary. Does switch now work? Yes

  • A201

Pg. 4-2

Page 50

Black or Solid Colored Screen Troubleshooting

Use swapout procedure to identify which Defective switchboard

board is bad.

Pg. M16 Detective Motherboard

Is b-5v pp 42 signal Yes fs present on A202 pin 39?

No Swapout Is 4-5v p-p 1) x200 osc. signal No 2) Q200 present between 3) Q2o1 C203 and R203? 4) Other Clock Circuit Components Yes

Is 4-3v p-p = . signal N en between present on -] C203 and pin 11 Reoair pin L1 A201? A201.

Yes

Is 6-5v pep Ne Y 40 signal a Swap Does unit function? os present on ainaod pin 4 A201? _ 7 lo

Yes

Pin 4 A201 shorted. Is 6-5v pop Repair

40 signal No Open berween

Present on Pin 27 A200 pin 27 A200? and Pin 4 A201.

Yes

No Swapout Yes

bs-sv pel 1) A200 Does unit function? 2 signal 2) A202 present on pin 28 A200? fis

ves Pin 28 A200 is shorted.

Repair Is 6-5v p-p 62 signal present No Open between ‘on A201 pin 26? Pin 26 A201 and Pin 28 A200.

Yes

Open berween Pin 39 A202 and <pin 28 A200.

A

Pg. 4-2

4-9 2600/2600A Domestic VCS

Page 51

Black or Solid Colored Screen Troubleshooting (Continued)

<>

Is 4-5v p-p Open trace

42 signal ie between pin 26

present ca A201 and pin 39

pi ? A202.

Yes

Is there +5v and No ground on all of A200, A201, A202, A203? Open on line to +5 or ground.

i—— Yes . —, —— ey

Reset and ready lines good? Open or shorted line.

Yes

Swapout

  • A200
  • A202
  • A201

Does unit operate properly?

Yes << Pg. 4-45

| Repair

Pg. 4-2

4-10 2600/2600A Domestic VC

Page 52

Snowy Screen Troubleshooting Procedure, Motherboard

Use swapout procedure to identify which board is bad. Bad switchboard.

Pg. 4-12 Bad motherboard.

Is +5v present at J201 Pin 1? Pg. 4-31

No

Swapout 7 Ye Is +9v present 1) A202 Is|modula tion es at J201 Pin 2? FH rH thaIVisesen? No Lt

Is modulation es

evident on the TV screen? Is there continuity across J201 pin 27

No

Check for open masta Nah trace line between (the power jack)? 1204 and 3201. Check at bottom of board. Pg. 411 Pe 4ell

No

Is 1204 OK? Voltage shorted to ground.

Fh

Replace J204,

Pg. 4-2

Page 53

*Caution: Observe polarity of continuity checker. Do Not put + probe on ground. | Snowy Screen Troubleshooting Procedure, Motherboard, (Continued)

a

Is modulation evident on the TV screen? to No

Check replace shorted . caps: C204,C201,C220, C€239,C200,C214. for and Pg. 4-2 | N Yes

  • ; Is there Replace connector. Is modulation oes 1201 1 evident on Pine 13,6 [i the screen? 10,117

Yes

Is there Is there an continuit: No open trace on between ov either +5v line and ground?* or ground?

Yes No |

Check for and repair any shorted traces or solder bridges.

Is modulation evident on the screen?

2600/2600A Domestic VCS

Page 54

Bad/No Color, Bad/No Sound Switchboard

a

  • r == Is RF mod Can unit be

output tuned No 7 tuned to No Replace RF &

to 61.25 MHz? 61.25 MHz modulator. (Channel 3) (+ «15 MHz)?

Yes Yes oe

No Is color ] Yes

~~ (or sound) now OK? |

(=, Short across L101. Does color No Replace RF | (or sound) re- modulator. appear? |

Yes

Replace LIOI.

A Pg. 4-2

Page 55

Gray Bars Troubleshooting Procedure

Is there a 3-5v p-p signal on the A203 side of R222, R223,R224? Check R222-R224 with Ohm meter. Replace any failed or off-value resistors. Pg. 445

Do all of pins 2, Yes} There is an open line 12, and 15 on A203 between A203 and the have a signal present? resistors. Fix it. No Pg. 4-5

Check inputs of Yes A203 (pins 3,11,14). Replace A203. Does each have a signal present? ae Pg. 4-2

Do all of pins 5,7,8 Yes Check for open

on A201 have a signal lines between A201

present? and A203. Fix.

No

Swapout A201 chip.

Pg. 4-15

Page 56

Gray Bars Troubleshooting Procedure (Continued)

ave

Picture Now OK? (See Figure 4-4)

No

Make sure R213, R219, R220 have +5v connected to top side.

T Check R218,R219, R220 for proper values.

Inspect traces around LM lines for shorts or opens.

Is picture now OK? Yes

Yes Go to matrix test.

(See Figure 4-4) SS No

Swapout A200 and then A202.

——L Is picture now OK? Yes (See Figure 4-4)

No

Pg. 4-45 Pg, 4-20

2600/2600A Domestic VCS

Page 57

Colored Screen Troubleshooting Procedure Switchboard

Bad Switchboard

Is +5v at JIOL No Pin 1?

oe Yes Pg. 4-17 = — Is RF mod. output Tune RF mod. If RF mod cannot be tuned to 61.25 MHz No at adjustment tuned to 61.25 MHz, (channel 3, + .15 hole. replace it. MHz)

Yes

Se Is video Check for open trace signal pre- Yes} or bad connection besent at J10! tween J201 and RF pin 12? module pin. a ———— Repair. No

Is J101 pin 12 shorted to ground?

Yes

Check for shorted trace. If none is found, the RF module is shorted and must be replaced. Defective JI0L. Replace.

Pg. 4-2

4-16 2600/2600A Domestic VCS

Page 58

Colored Screen Troubleshooting Procedure, Switchboard, (Continued)

Is +9v present Yes a at J101 Pin 2? [=

Check that J101 pin | or 2 is not shorted to ground. at

Check that C101, C103, or C106 are not shorted. Replace if shorted. Is C101 shorted? Replace C101.

Replace voltage regulator (A101).

If +9v is still Not present at J101 pin 2, then replace the regulator (A101).

Pg. 4-20

Page 59

Snowy Screen Troubleshooting Procedure,

Yes

Is +5v at the RF Switchboard

Is +5v present Ne at J101 pin 1 = on the switchboard?

Pg. 4-19

No | Open between A101

or pin 2 (3 pin mod)? moduleipint3é

Yes

Check for and Ooes RF modulator No repair opens bepin | have continuity to ground?

Make sure RF module output is tuned 10 61.25 MHz. (+ .15 MHz).

If there is still a white screen, check the J102 connector. Replace as required.

If no modulation, the RF module is bad. Replace. RF module pin | and J101 pins 6 and 10 (ground).

Is there modulation?

Pg. 4-2

2600/2600A Domestic VCS

Page 60

Snowy Screen Troubleshooting Procedure, Switchboard, (Continued)

. — —=y Check for and Is +5v at the Yes repair defective output of the voltage 3101 or open trace regulator (A101, pin 3)? between J101 pins and Al0l. ——EE ——— | No

Check for Is unregulated y bad regulator +7.5-9v at voltage = (A101) of open regulator input between ground (A101, Pin 1)? and AJOl.

No aa ae ee — — Is +7.5-9v present [YS Replace Siol. on the J101 side of $101?

Does J101 pin 2 have continuity? No

Is J101 pin 2 shorted to ground? Yes

‘Check that C103 or C106 have not shorted to ground.

Is there modulation?

A Pg. 4-2

Page 61

Matrix Test Procedure

Initialize switches, then push "left" difficulty switch down. TE Does screen No match Figure 4-6?

Yes

Put in shorting plugs.

Does screen match Figure 4-7? No

Yes Pg. 4-23

Push down “Game Select" switch (S106).

Did lower middle No block on screen turn black in center?

Yes

Push down "Reset" switch (S105)

Does lower middle block turn black on left and right ends? No

Yes Pg. 4-7

Page 62

Color Troubleshooting Procedure,

Use swapout procedure to Motherboard

Defective switchboard.

determine which board is bad. a Defective Motherboard X200 frequency correct? (3.546 + .04MHz) No = Defective x2! |, eee

Yes

Is color very weak or not present

Yes

With R211 fully counterclockwise is there 6.5-7.5v on pin 10 A201?

Is there +6-7v on No

at all?

Yes 208,C209,R211 Pg. 4-22

‘Swap

  • A201
  • A200
  • A202

Defective

the cathode of CR201?

—E—

Is there a 3-5v p-p Yes} Defective CR200. [LJ or open trace — between CR201 and pin 10 A201.

signal on cathode CR200?

Is there a 3-5v p-p signal on cathode CR200?

Open or shorted trace to diodes (CR200 or CR201) Defective CR201

Replace or Repair

Pg. 4-2

2600/2600A Domestic VCS

Page 63

Color Troubleshooting Procedure, Motherboard, (Continued)

Swapout

  • A201
  • A202
  • A200

Pg. 4-2

Is 3.5-5v P-P signal prery

| Defective R215. sent between C213 and R215?

Defective C213

signal present Defective C212 pin 9 A201?

No

Pin 9 A201 shorted to another line.

ee ed

Replace or Repair

Pg. 4-2

Page 64

Defective Matrix Troubleshooting Procedure

The pattern may have errors, but all nine blocks are oresent on screen.

Partern is disrupted u Uf dtue oF Diack lines Is blue black grid pattern Swapout Yes are Missing of some disrupted? Bee Figure {Yes 0) A200 {s entire racrix portion of the Mawixf* ~~] 48 for example bad 2) A202 now on screen? fails to appear on the: pattern) 3) A201 TV screen. —— No No

{s upper left block on 5 screen defective? Ad (See Figure 4-6 or 47 for correct pattern) Pg. O45

Pg. Hi6 No %

Are either the middle Swapout Are middie-iett lower or the left lower } Yes 1) A202 and lower-ievel vas. block defective? (See 2.4200 blocks now cor~ Figure 8-6 or 4-7 for 3) azat cect (See Figure Correct pattern) 4-6 of 4-7)?

No No

ts upper-middle 26: Ar block defective?

Ne Pg. 4-27 Pa. 426 v3 Swagout Yes 's middle-middie scr A200 Is middie~niddie dlock detective? 2) A202 block now OK?

  • A201

hy No =

Is lower-middle Yes block defective?

No’ Pg. 627 Pg. as

Pg, 4-20

Page 65

Audio Test Procedure

Reinitialize switches. Press down the "right difficulty" switch.

Is there a clear tone?

Use scope or frequency counter to measure frequency at emitter of Q202.

Tune audio to 5.5 MHz by adjusting L201.

Adjust to + .06 MHz. Look for stable frequency.

Can unit be adjusted and is sound clear?

Pg. 4-23

2600/2600A Domestic VC

Page 66

Audio Test Procedure (Continued)

Are the two patterns in Figure 4-9 No alternating on the screen?

Yes Pg. 4-24 —— $1, Do the patterns alternate with the tones?

Swapout Are both colors Are patterns and tones con- 1) A201 now correct? sistent en z re (As in Figure 4-9) cye:

Put switches back to initialized positions. = =

YCS will go through one last cycle before changing to color bar test.

= Pg. 30

Changed per ECN #0021 1/29/83

Page 67

Defective I/O Lines Troubleshooting Procedure

<>

Defective A202 Cap. Connector Determine (RAM) Line No. No. Pin No. which lines are —TS C2355 203-Pins defective by 18 C234 3202-Pin 3 referring to I 13 C233. 3202-Pin 2 Figure 4-7. 12 C232 -3202-Pin | = iv C231 3203-Pin & 10 C230 1203-Pin 3 9 €229—-1203-Pin 2

  • Check the lines 8 C2zzg3203-Pin 1 indicated as defective for +5v at 3202 or 3203 (See chart).

‘Swapout Is +5v present Yes 1) Az0z Paes "no bok Yes on the line(s) 2) A200 correct (See just checked? 3) A201 Figure 4-6 or 4-7)?

No No

yeck the RAM Yes] Repair open trace Repair line Ch (A202) pin. Is +5v between A202 pin 5 present there? and the 3203/3203. (check once ine No !

Check trace line(s) from defective pin(s) . for shorts to ground. Repair Are there any shorts?

No

Swapout A202.

Is +5v now Yes present at the A202 pin?

No

Replace the capacitor on that line (see chart).

Does the Diagnostic | No Swapout Marrix screen now ) A200 foo" correct (see Fig. 4-6) 2) A201

Yes

A

Pg. 4-2

4-26 2600/2600A Domestic '

Page 68

<=> Trigger Line Troubleshooting Procedure

Is +5v at pin 6 Check/repair trace lines Check for VMOD of 3203 (right) No_}from: R225 to 1203, pin 6| (+5v) at top of Is trigger line Yes trigger) or 3202 (right), R226 to 1202, R225 (right) or now operating (lett trigger)? pin 6 (left). R226 (left) correctly?

Yes No

ir open trace from: prea nes ro R225 to A203 Is trigger line ws trigger) and pin 9 (eight) now operating left trigger) R226 to A203 properly? (left) 1s ——— Yes TS 4.3-3v ar \ - Tee A203 pin 6 Swapout A203. Row operating (right) and No conc? pin 10 (left)?

Yes No

Swapout A201

‘Does trigger line now work ws

properly?

No

Swapout

  • A200
  • A202

Does trigger line [Yes now work properly?

Check/Repair €236,CR202 ft) ) €237,CR203 (ight)

Pg. 2

2600/2600A Domestic VCS

Page 69

Audio Troubleshooting Procedure, Motherboard

caw D

Switchboard Use swapout procedure | Bad to isolate the bad board.

Bad motherboard — Pg. #13 square wave which Is one fre- No i

Is there a 2v p-p F

Thema bereeen Eee ‘quency appearing No Is +5v at the top Reesk open rece

two frequencies on at the pin? of R208? peewee aaa Yes es Yes

Pin 13 of A201?

Is there continuity No| Repair open between Swapout A201. from R208 to A201 R208 & A201 pin 13? Pin 13.

Yes

‘Swapout A201. AD ] Pg. 4-24

Does square Fix open trace line

wave signal appear O24 between C210 and AD

at C210? pin 12/13 of A201.

te Pg. 4-26

Is there a 4.5 MHz, modulated 1-2v p-p | No audio signal at C211 (either side)?

Pg. 9-29 Yes u 5 Is there now an alter- Nau

  • R216 nating audio tone from the TV’ Yes

No Pg. 0-2

2600/2600A Domestic VCS

Page 70

Audio Troubleshooting Procedure, Motherboard, (Continued)

<>

Check that L201 is good (has continuity and isn't shorted or cracked).

Check/Replace

  • C206, C207
  • Q202
  • L202

If audio is still dead, check the trace lines around C211 for opens and shorts:

Is there now Ee

an alternating Yes audio tone from the TV?

No

AH

Pg. 4-28

4-29 Is there +5v No Repair trace at one end of from VMOD (+5v) L201? to L201.

Yes

Pg. 6-2

2600/2600A Domestic VCS

Page 71

<=>

DTC works, but VCS unit is still suspect.

Plug in customer cartridge, if L available.

Available

Connect, initialize, and turn VCS on with customer's game cartridge.

Does correct N video pattern I Cartridge Test Procedure

Not Available

Pg. 4-31

for that game appear?

Yes

I Play game. Does it play OK?

INo a Pg. 4-31 Check customer Yes cartridge on known Yes

Swapout

  • A201

good game. Is it OK?

No

Replace with good cartridge.

AK

Pg. 4-31

  • A200
  • A202 Does game now operate properly with game cartridge?

No

Pg. 4-45

2600/2600A Domestic VCS

Page 72

Burn-In Procedure

<=>

Place customer cartridge in game, if available. Otherwise, use other game cartridge.

ft Run game for 2 hours, minimum. Do not turn off during this period.

Check game's operation.

Is game working End of test sequence. properly?

Pg. 4-2

Page 73

Defective Switch Troubleshooting Procedure

—2 >

Put inoperative switch in up (open) position.

ls +5v present atthe | no Is wace Yes 1201 pin for that switch line shorted (see connection chart)? to ground? Repair

Yes

Is there continuity across 201 connector? Change 5zu1

Yes

Bur switen in down (closed) position.

Is év now present on 3201 pin for Yes that switch (see chart)? Pg. 6-2

Is one side of switch tied to ground as shown Replace switch. in schematic?

Repair open

ground.

CONNECTION CHART Does pattern Switch 2101 Pin No. on screen No Color /Biack & White change when Left Difficulty switch is Right Difficulty flipped? Select ewe Reset

Pg. 4-2

Page 74

Snowy Screen Troubleshooting Procedure

2600/2600A Domestic VCS AM

Is there dv No on J201 pin 12? re: Yes

Is there Is the re oe No an open line Yes Repair. eesoie between pin . 20 and +5v? —— = Yes No Is there Yes

Swapout A201. FL modulation?

Lag No

Is there continuity No 0 across J201 pin 12? Replace 3201

Yes ~—— — Is 3201 pin 12 Are C221 oF aroma? (eho Nes R223 shorted Yes} Replace 7 ? continuity) * tolgnound?

——! ——! No No Check for ] Swapout A201. solder bridges Repair or trace shorts. L. See el

  • =

Is there No Svepeut

modulation? 2) A202

Yes |g |

A

Pg. 4-2

Page 75
  • ==; Put shorting plugs in. Put VCS into Diagnostic Matrix mode.

aa Paddle Lines Test

No ‘Check 3202/3203 for RC —— repair wavetorm (see Fig. 4-10). }yes Seen alte Asor aia No me barren Do paddle lines now | Yes >

in chart? = — Yes No

Swapout

  • A201 2)A200
  • A202

Is there con= Sinuity, between, No] Check trace lines and tae ) LA resistors for opens. and the A201?

Yes

Replace cap (C215-C218) on the failed line. ara

Does RC waveiorm appear on the appropriate 1202 ‘or 3203 line? (See Chart)

‘Swapout

  • A201
  • A200
  • A202

Does Paddle Yes Line now work?

No {. Paddle Tine is open + Repair A

con Pg. &2

Player A201 3202 203 No. T wo > = Cais 2 39 9 = C26 5 3 —- 35 QI 4 37 = 9 Cals

4-34 2600/2600A Domestic VCS

Page 76
NOTE: The following figures are referenced in the 2600/2600A Diagnostic Flowcharts, Sections 4 and 6, and are included here for your convenience. They can also be found in Section 3, where the tests are described in more detail.

LEFT = CX2600 RIGHT GAME GAME TV TYPE CIFFICULTY GIFFICULTY SELECT e&SET

a-w FOWER oN couse Ay 4 A = =

OFF 8 6 e 7

initially to the left

Figure 4-1. Switch Initialization Positions

Page 77

REFERENCE BAR

Figure 4-2. Color Bars Screen

NOTE: Set all switches to initialized position. A screen of horizontal color bars is displayed (see Figure 4-2). The screen should be steady and unchanging. A gray or blue horizontal reference line runs across the screen about three bars from its bottom. This reference line is thinner than the bars around it. R211 (R213 on the 2600A board) should be adjusted so the bars immediately above and below the reference line are within one shade of each other. Proper operation of the unit is indicated by being able to make this adjustment and by consistent color within the entire span of each bar on the screen. Minor glitches on the edges of the color bars are acceptable. Leave this test on for at least ten seconds in order to catch any intermittent problems, such as a bar momentarily changing colors or blanking out.
Page 78

fo oo

ANY DIAGONAL LINES ON THE SCREEN INDICATE A FAILURE IN THE RAM CHIP (A202).

Figure 4-3. Defective RAM Patterns

Page 79

Figure 4-4. Gray Bars Screen

The gray bars screen has eight horizontal shaded bars. It is normal for the bars to have some uneven areas on their upper and lower edges. The bars must appear (in descending order) as going from black to white in even steps. The screen may not have any color in it. All eight bars must be consistent in their shade across the entire bar. The area of the screen outside the bars is irrelevant. The white line immediately above the top bar (black) is normal. This screen tests the operation of the chip set, especially the TIA (A202).

Page 80

Figure 4-5. Defective Gray Bars Screen

This screen shows an example of a defective gray bars test screen. The appearance of a black rectangle in the middle of a light gray bar means that the data for that part of the screen has failed to be translated properly to the TV. Any disruption of the standard gray bars pattern (See Figure 4-4) or any color in the gray bars screen indicates a failure.

Page 81

T Pink Pinte =

slilatelayat2]a) bee 2) HE a) ja} dal da fas a ajle|dcetec|eleds f= Pik or Green Not Used elelele]é lee fF ne ied

Vda (2) lat | PPABT @ THUY) fel fel fa fe == oat ele dele ]elels]s Rene Sth fom Nove ele jele pele dese Settch Switch Selch

6532 iT

Figure 4-6. Diagnostic Matrix Screen (Shorting Plugs OUT)

The Diagnostic Matrix Screen appears as above, on a black background, when the shorting plugs are not inserted. The three left rectangles and the blue/black grid joining them indicate the status of the I/O line connections to the 6532 RAM chip (A202).

Page 82

9 a

Se ee 13 eves Not Used Right |S | Not Used élejelelepepelé Z| oie |= = 4 oy M 4

s}3d3 3 ls A 3 3] E Fi g{d)a]ayalalala] BVA | ale 3} yay dap ya Ges ceed alzlay«.]=fels | Not Used 2|z|2]s 3 ores elelelelé}éla |@ rag

: : F 3 A 2] | 2 2] |2 g) BE 4 Ly 31 | 3] | a] [a rm as «ts Loe distie ite his oo came — ee ee yelee ws We Bet Nl Reset Select Reset Not Used Els le pepele PS PE Switch Switch Seiten

Figure 4-7. Diagnostic Matrix Screen (Shorting Plugs IN)

2600/2600A Domestic VCS

Page 83

, - i ‘ cece s yee 72,2 ye 73 ]s oe elelele]zelélels ey] me |? q 3

a 3 aya ays | HAH a) ]a] jay 2 oan s cm epee ],2 7272 18 1s Pink ov Green Not Used slelé]e]é]é fa lé Not Uae

a] y3) 72] [2] |] BIBPEH 2 [Bigdsl dal Jat vad da

wes Cecen ale]deo]tse [ele fe ]s Game Game Came Green ele lel ]ele faye Seiten Sten Sch Netbed

on L

Figure 4-8. Diagnostic Matrix Screen with Defective Pattern

Any missing grid lines or disrupted rectangles indicate an I/O line failure (see page 4-26). Any missing or disrupted blue or black reference lines indicate that there has probably been a microprocessor failure (see page 4-23).

Page 84

Figure 4-9. Audio Tone Test Screens

The test displays two alternating patterns on the screen (as shown in Figure 4-9) while two alternating tones are heard. The tones change in sync with the screen. This test pattern continues for one full cycle after the Right Difficulty switch has been switched to stop the test.

Page 85

2ms/div. lv/div. Pin 37 and Pin 39

2ms/div. lv/div. Pin 38 and Pin 40

Figure 4-10. RC Waveforms

Page 86

©

SIGNAL TRACING CARTRIDGE (KLUGE) PROCEDURE

The Signal Tracing Cartridge (STC) is used to locate easily open or shorted traces in the address and data lines of the 2600/2600A. The STC causes the 6507 microprocessor (A200) to cycle through the entire memory space while executing "no operation" instructions. This is valuable because it puts a known signal on each address and data line. Then the signal can be traced through to the J200 connector, the TIA and RAM-I/O chips.

Since the STC procedure is not easily reduced to a flowchart, it is presented as a series of written instructions and illustrations on the following pages.

CAUTION: _The STC procedure requires three known-good chips and_a working clock circuit. The STC should only be used after all other procedures have been tried.

GETTING STARTED

Insert the STC into the 2600/2600A. Turn on the unit. The television screen should be gray or black. If it is "snowy" it indicates that you should return to the start of the Diagnostic Flowchart. Set the scope sweep to .5 microsec/division and set the vertical to | volt/division.

ADDRESS LINES AB@- AB12

Check the address lines at:the microprocessor (A200). Check address lines, starting with pin 5. A signal with a waveform similar to those shown in Figure 4-11 should be seen on the address lines, with each succeeding address line's waveform having a frequency half that of the line before it. For example, Al should be half the frequency of A@. If one or more of the address lines shows no signal, it is likely that the line is either open or shorted to ground or +5v. Check all traces and pins for shorts.

If you have a defective address line and it is not open or shorted, swapout the A200, A202 and A201, in that order.

If all address lines have signals, trace those signals to the J200 and the other chips. Table 4-1 illustrates which address lines connect to which pins on J200, 6532, and the TIA. The signal present on each address line of the microprocessor should also be present on each pin of J200, 6532, and the TIA connected to that line. If the same signal is not found, the trace line and/or solder joints between the microprocessor and the dead pin(s) is (are) broken. Check the trace lines carefully to locate the break.

DATA LINES DB@-7

Set the vertical on your scope to 2v/division. The data lines are tested very much like the address lines. The only difference is that the waveform seen on the data lines is different. The signals you should see are illustrated in Figure 4-12. If any data lines are completely inactive (simply remaining a constant voltage), it probably means that the line is either open or shorted to ground or +5v. Check the traces and pins for shorts. If none are found, one of the three chips or the STC itself probably has an internal short. Try swapping out the 6532, TIA, and the microprocessor. Also carefully check J200 for shorts between pins.

Page 87

If all data lines have signals, trace those signals to J200 and the other chips. Table 4-1 illustrates which lines connect to which pins of J200, 6532 and the TIA. The signal Present on each data line of the microprocessor should also be present on each pin of J200, 6532 and the TIA connected to that line. If the same signal is not found, the trace line and/or solder joints between the microprocessor and the dead pin(s) is(are) broken. Check the trace lines carefully to locate the break.

Address lines 0, 7-12 Address Lines 1-6 1v/division 1v/division

Figure 4-11. STC Address Line Waveforms

Data Lines 0,2, and 4 Data Lines 1,3,5-7 2v/division 2v/division 2ms./division 2ms./division

Figure 4-12. STC Data Line Waveforms

Page 88

TABLE 4-1

Connected Pins on Motherboard

ADDRESS A200 A201 A202 3200 LINES (MPU) (TIA) (RAM) Connector

ABO 5 32 7 8

ABL 6 31 6 7

AB2 t 30 5 6

AB3 8 29 4 5

AB4 9 28 3 4

ABS 10 27 2 3

AB6 ll - 40 2

AB7 12 21 (CS3) 38 (CS1) L

AB8& 13. - -- 22

AB9 14 _ 36. (RS) 21 AB1O 15 = a 19

ABIL 16 - ip 20

ABL2 17 24 (CSO) 37 (CSO) 18

DATA LINES:

DBO 25 14 33 9

DBL 24 15. a2 10

DB2 23 16 31 ll

DB3 22 \7 30 13

DB4 21 18 29 14

DBS 20 19 23 15

DB6 19 33 27 16

DB7 18 34 26 17

-- Indicates no connection on that line

Page 89

SECTION 5

SYMPTOM CHECKLIST

The Symptom Checklist is designed to assist the experienced technician arrive at a rapid diagnosis of VCS problems. The checklist is not intended to replace the Diagnostic Flowchart as the primary troubleshooting guide, but is designed to supplement the flowchart.

Symptoms have been divided into six general categories of failure:

Logic

Video

Color

Audio

Controller

Other

Each symptom is accompanied by some possible cuases and the best point to enter -the Diagnostic Flowchart to locate the problem.

Page 90

SYMPTOM

Solid colored screen

Vertical lines

SYMPTOM

Snowy screen

Weak picture

Wrong Gray Bars 2600 FAILURES

LOGIC FAILURES

POSSIBLE CAUSE (motherboard) POSSIBLE CAUSE (switchboard) DIAGNOSTIC FLOWCHART ENTRY POINT

A200, A202, TIA X200, Q200, Q201, open or shorted Address or Data line

A200, A201, A202, J200, open or shorted Address or Data line A101, RF Module

N/A

VIDEO FAILURES

POSSIBLE CAUSE (motherboard) POSSIBLE CAUSE (switchboard) J, pg. 4-9

J, pg. 4-9

DIAGNOSTIC FLOWCHART ENTRY POINT

no power, A203 3201, 3204

N/A

A201, A203, R218-R220

5-2 A101, L101, RF Module, J101

L101, RF Module, RF Cable

N/A L, pg. 4-11

X, pg. 4-18

P, pg. 4-14

2600/2600A Domestic VCS

Page 91

SYMPTOM

No color

Only the reference bar appears

Color won't adjust

Weak color

SYMPTOM

No audio

Weak audio

DTC audio test fails 2600 FAILURES (Continued)

COLOR FAILURES

POSSIBLE CAUSE (motherboard)

X200, A201

C208, R211

R211, C208, C209

C212, C213, R215

AUDIO FAILURES

POSSIBLE CAUSE (motherboard)

C206, C207, L201 adjustment, Q202

A201, C206, C207, L201 adjustment, C201

A201, A200, A202 DIAGNOSTIC POSSIBLE CAUSE FLOWCHART

(switchboard) ENTRY POINT

L101, RF Module AA, pg. 4-21 RF Cable

N/A AA, pg. 4-21

N/A - AA, pg. 4-21

RF Module, L101 AA, pg. 4-21 RF Cable

DIAGNOSTIC POSSIBLE CAUSE FLOWCHART

RF module AH, pg. 4-28 adjustment

RF module AH, pg. 4-28 adjustment

N/A AD, pg. 4-24

2600/2600A Domestic VCS

Page 92

SYMPTOM

Fire button does not work

Joystick does not work

Driving Controliers

Paddle Controllers

SYMPTOM

Switches not working 2600 FAILURES (Continued)

CONTROLLER FAILURES

DIAGNOSTIC POSSIBLE CAUSE POSSIBLE CAUSE FLOWCHART

(motherboard) (switchboard) ENTRY POINT

A203, 3202, 1203, N/A AG, pg. 4-27 defective Controller

A202, 3202, 1203, N/A AF, pg. 4-26 defective Joystick

A202, J202, J203 N/A AF, pg. 4-26 defective Controller

A201, C215-C218, N/A pg. 4-34 3202 - 3203, defective controller

OTHER FAILURES

DIAGNOSTIC POSSIBLE CAUSE POSSIBLE CAUSE FLOWCHART

A202, C222-C227 $102-S106, J101 AL, pg. 4-32

Page 93

SYMPTOM

Solid colored screen

Vertical lines

SYMPTOM

Snowy screen

Weak picture

Wrong Gray Bars Revisions 1-13

Wrong Gray Bars Revision 14

Warped picture Revisions 1-13

Warped picture Revision 14 2600A FAILURES

LOGIC FAILURES (2600A)

POSSIBLE CAUSE

A200, A202, A201, X200, Q200, RF Module

A200, A201, A202, 1200, open or shorted Address or Data line

VIDEO FAILURES (2600A)

POSSIBLE CAUSE

A203, S201, RF Module, L205

RF Module, RF Cable

A201, 2218-221, R214-R217

A201, R218-R221, R229, R230, CR202, CR203, R214-R217

A201, R221, R217

A201, R217, R221,R236, R203

5-5 DIAGNOSTIC FLOWCHART ENTRY POINT

I, pg. 6-10

I, pg. 6-10

DIAGNOSTIC FLOWCHART ENTRY POINT

K, pg. 6-12

K, pg. 6-12

M, pg. 6-14

N, pg. 6-15

C, pg. 6-4

Cl, pg. 6-5

2600/2600A Domestic VCS

Page 94

SYMPTOM

No color

Only the reference bar appears

Color won't adjust

Weak color

SYMPTOM

No audio

Weak audio

Diagnostic test cartridge audio test fails 2600A FAILURES (Continued)

COLOR FAILURES (2600A)

POSSIBLE CAUSES DIAGNOSTIC FLOW CHART ENTRY POINT

X200, A201, C210, C211 RF Cable

R213, C205, A201P, pg. 6-16

R213, C205, CR200 CR201

RF Module, C210, C211, R210, RF Cable

AUDIO FAILURES (2600A)

POSSIBLE CAUSES P, pg. 6-16

P, pg. 6-16

P, pg. 6-16

DIAGNOSTIC FLOW CHART ENTRY POINT

C206, C207, Q201, RF Module adjustment

A201, C208, R207, C206, C207, RF Module adjustment

A201, A200, A202

5-6 X, pg 6-24

X, pg. 6-24

X, pg. 6-24

2600/2600A Domestic VCS

Page 95

SYMPTOM

Fire Button does not work

Joystick does not work

Driving Controllers

Paddle Controllers

SYMPTOM

Switches not working 2600A FAILURES (Continued)

CONTROLLER FAILURES (2600A)

POSSIBLE CAUSES

3202, J203 Defective Controller

A202, 3202, 3203, Defective Joystick

A202, 1202, 3203, Defective Controller

A201, C218-C221, 3202, 3203, Defective Controller

OTHER FAILURES (2600A) .

POSSIBLE CAUSES

A202, C231-C235 $202-S206

5-7 DIAGNOSTIC FLOW CHART ENTRY POINT

W, pg. 6-23

V, pg. 6-22

V, pg. 6-22

pg. 6-29

DIAGNOSTIC FLOW CHART ENTRY POINT

G, pg. 6-8

2600/2600A Domestic VCS

Page 96

SECTION 6

2600A DIAGNOSTIC FLOWCHART

The Diagnostic Flowchart is intended to be easy to use and the primary aid when troubleshooting the 2600A. Follow the prompts in the order presented. The figures referenced in the flowcharts are located at the end of Section 4, beginning on page 4-37. When a question is asked, follow the line from that box which best applies to the unit's situation. When a line terminates with a letter inside a circle, note that a page number (ie., pg. 6-3) is near it. Turn to that page, locate the letter in another circle, and continue the diagnosis. The flowchart leaves nothing to chance, it tells you when to perform a specific test, and when to replace components, and even when and how long to "burn-in" the unit. "Burn-in" the unit for at least two hours after completing repairs.

When a problem is extremely difficult to diagnose, the flowchart sends you to the Signal Tracing Cartridge (STC) routine, "D", page 4-47. Due to the repetitive nature of the STC routine, no flowchart is used. Read and follow the instructions as directed. Should the STC procedure fail to isolate the problem, after carefully inspecting the motherboard assembly for shorted and/or open trace lines and solder bridges, swap all three chips (6507, 6532, and TIA). Should the problem still persist, call ATARI, Techline Specialist: Inside California at (800) 672-1466 and Outside California at (800) 538-1535. Be certain to always burn-in the unit for two hours after completing repairs. This helps to ensure that intermittent problems are found and also greatly increases your customer's satisfaction with your repair work.

SWAP OUT PROCEDURES

Many places in the diagnostic flowchart; a box tells you to "swapout" a chip or a number of chips in a particular order. The "swapout" instruction means that you should replace the indicated components one at a time with a known good component of the same type. The VCS should then be tested with the new, known-good component in place to see whether the "swapout" solved the problem being checked. If the swapout did not fix the problem, the known-good component should be left in, and the‘next component inserted. Once the problem is solved, you then place the suspected bad chips one by one into the system to determine whether or not those you pulled out are truly defective. In this way, you avoid needlessly replacing good components.

CAUTION:

Extreme care should be taken when handling the intergrated circuit chips (A200, A201, A202, A203). They are all very sensitive to static electricity and can easily be damaged by careless handling. Always keep the chips in their plastic carrier tubes or on conductive foam when not handling them. Make certain you are well grounded when handling the chips. Atari strongly recommends that you wear a conductive grounding band (which ties from your arm to ground) when handling the chips.

The chips are also susceptible to damage from stress when being removed from or inserted into the sockets. Always use a chip-puller when removing the chips. Do not pry chips out with a screwdriver or any other tool.

Failure to follow the above guidelines results in unusually high chip failure rates and extra expense.

Page 97

2600A Diagnostic Flowchart

Connect VCS to TV battery eliminator. Set TV to channel 3.

Insert Diagnostic Cartridge (DTC), initialize (Figure 4-1) and turnon, -

Does any de~ : 1s picture fective RAM s No | warped and ragged | Yes Pg. 6-4 oF pattern spear on left side Pg. 6-5 Fig. 6-3). otiacreent

C - 2600A Revs. 1-13 y. es No C1 = 26004 Revs. 14 and up

Replace the A202. 8 ) P63

: . Does unit "7

  • roy ‘unit now No cole burs parton? 2) Aros pat
  • A202 bars pattern? Ta = I Yes Pg. 0-45

A

Page 98

2600A Diagnostic Flowchart (Continued)

Are color bars present? (See Figure 4-2).

No

Is any other test pattern on the screen? (See Figure 4-4, 4-6,4-9).

[=

Is there "snow" on the screen? (no modulation) Pg. 6-7

Are color bars properly adjusted? (See Figure 4-2)

Check your switch settings. Are they correct?

Is ANY modulation Present on screen? Pg. 6-6

Pg. 6-3 No

Yes

Check VCS

  • connections to TV and channel setting.

Test VCS with known - good battery eliminator.

le

et Is "snow" on screen gone? Pg. 6-10

a

No

Pg 6-12

6-3 Pg. 6-2

2600/2600A Domestic VCS

Page 99

2600A Bad Video Troubleshooting (Loss of Sync.) (Revisions 1-13)

RF _ module tuned to Can R F_ module be 61.25 MHz? (Channel 3) properly tuned?

Tune R F module

3.5-5V P-P signal on A201 side of R217. Defective R217 or bad A201.

Swapout

  • A201
  • A200
  • A202

vi Good video P—— Replace R F_ module

No

Defective

R221 H Replace

ee

—~<-

Pg. 6-2

6-4 2600/2600A Domestic VCS

Page 100

2600A Bad Video Troubleshooting (Loss of Sync.) (Revisions 14 and up)

Can RF module be properly tuned? RF module tuned to 61.25 MHz , Channel 3? Replace R F module.

Yes

Tune R F module.

——== Defective R217 or defective CR203. or defective A201. 3.5-5V P-P signal Yes on A201 side of R217.

Swapout

  • A201
  • A200
  • A202

Good video YES

Defective R221 or R230 Replace.

Pg. 6-2

Page 101

2600A Gray Bars Test Procedure

>

Place color/ black & white switch in B&W position. [

Did screen pattern change when switch was moved ? err

Is proper gray bar pattern

present? (See

Figure 4-4).

Is a partial segment missing or is any color

Figure 4-5)

6-6 Pg. 6-8

No Pg. 6-13

Yes Pg. 4-45

Pg. 6-14 oF 6-15 M + 2600A Revs. 1-13 N - 2600A Revs. 14 and up

2600/2600A Domestic VCS

Page 102

2600A Color Bars Test Procedure

Reconnect VCS and initialize.

Are color bars present on screen?

a Yes Pg. 6-2

Adjust R213 so that color is aligned properly (See figure 4-2).

Is VCS tunable Yes to proper shades?

No Pg. 6-6

Pg, 6-14 oF 6-15 M - 2600A Revs. 1-13 N - 2600A Revs. 14 and up

6-7 2600/2600A Domestic VCS

Page 103

2600A Defective Switch Troubleshooting

CONNECTION CHART A202 Switch Pin No. Color/Black and White al

Left Difficulty 17

With inoperative switch N Right Difficulty 16

in open position, is there 0, Select 23

+5v present at the A202 eset 24 side of it? Pg. 6-9 Yes

Close the switch.

No

Swapout Y ls Ov now present at the } Ye: 1) A202 Does switch now work? ss RAM pin for that switch? 2) A200 (See chart) 3) A201

No

i Yes Is there an open between | No | Is switch connected to ; A201 and eae switch? ground on other side? Replace switch.

Yes No

a

Repair trace.

Pg. 6-2

2600/2600A Domestic VCS

Page 104

2600A Defective Switch Troubleshooting (Continued)

Is switch internally shorted?

Is cap on that line shorted Y€S¥ Replace cap. to ground? (See chart)

No = Is there +5v on the RAM Swapout pin for that switch? No 1) A202 (See chart) 2) A200

  • A201 CONNECTION CHART A202 Switch Pin No. Yes Color/Black and White Left Difficulty 17

Open between RAM pin Biers Difficulty 3

and inoperative switch. Reese 4

Repair

Pg. 6-2

6-9 2600/2600A Domestic VC:

Page 105

2600A Solid Colored Screen Troubleshooting

SS a

ls %5v pop D2 signal | Yes present on A202 pin 397

No Pg. 6-11

‘Change Is 43y pop onc. signal} Ng 1) x200 present between 2202 and 2) Qzo0 R208? 3) Other clock circuit comoonents

Yes

Ri 1s 625v pep ose. signal [No] Pen between R208 and present on pin 11 Az01? eee

Yes

ls 4=5v p-9 40 signal. | No svanout > bred, 4 Does unit function? Pin 4 A201 shorted. present on pin 4 A201? 24202

Yes

Yes

Pg. 6-2

No Jopen between 27 A200: {3 4-5v p-p DO signal p pin Repair oresent on pin 27 A200? and pin 4 A201.

Swapout Yes

Is 6-5v p-p @2 signar [NO 1) A201 Does unit function? oresent on pin 28 42007 2) A200

jo ves Pin 28 Az00 shorted to ground. Reoair. Is 4-5v pp 02 signal [NO pen bet pin 26 resent on pin 26 A20It go20ll and/pin'23/A200;

Yes

lOpen between pin 39 A202! and pin 28 A200.

2600/2600A Domestic VCS

Page 106

2600A Solid Colored Screen Troubleshooting (Continued)

aS

Is 4-5v p-p 02 signal No present on A201 pin 26? Open trace between pin 26 A201 and pin 39 A202.

Yes r Is there +5v and ground No on all of A200, A201, A202, A203? Open on line to +5v or ground, or bad regulator.

Yes

No Reset ready lines good? Open or shorted line.

Yes

Swapout

  • A200
  • A202
  • A201

Does unit

operate properly?

Yes No

Pg. 4-45 =

Repair EE

Pg. 6-2

2600/2600A Domestic VCS

Page 107

2600A Snowy Screen Troubleshooting Procedure

ts -Sv present on ourput [os Is there +5v on pin & [No a ame ad ee Reaanse RE module? 1205 defective? ut ane

Yes Yes

Replace RF module or Repair hes bad RF cable? Replace L205. L {

7.5 unregulated on A203 [Yes Defective A203. Replace input?

No

Yes bopen between 3201 and in - 7.5 unregulated on 3201? put Az03. Repair

No

Yes +5v shorted to ground? Repair

No

Swapout

  • A20L
  • A200
  • A202

Yes Anv modulation?

No

Defective 3201.

Replace

Pg. 6-2

Page 108

2600A Matrix Test Procedure

oe

Initialize switches, then push "left" difficulty switch down.

Does screen No match Figure 4-6?

Yes

Put in shorting, plugs.

Does screen match Figure 4-77

Yes Pg. 6-16

Pusn down, "Game Seiect" switch (S106).

Did lower middle No block on screen turn black in center?

Yes

Push down "Reset" switch (S105)

Does lower middle block turn black on left ana right ends? | No Pg. 6 Yes es

Pg. 6-17

6-13 2600/2600 Domestic YCS

Page 109

2600A Gray Bar Troubleshooting Procedure (Revisions 1-13)

a>

pin corresponding to the resistor that had no signal?

No a Check pullup resistor R218, R219, or R220 on that line to insure resistor is good and one side is connected to +5v.

Resistor Defective?

Swap

  • A201
  • A200
  • A202 pe
  • = ] Ts there 3-5vP-P |] Check R214, R15, and signal on the A201 Yes R216 with meter for side of R214, R215, correct value. | and R216? Replace any defective —E components. No

Is there 3-5v P-P_ [YES] Open between A201 signal on the A201 and that resistor. ah

Pg. 6-2

2600/2600A Domestic VCS

Page 110

2600A Gray Bars Troubleshooting Procedures (Revisions 14 and up)

Is there 3-5v P-P signal on the A201 side of R214, R215, and R216? —E Is there 3-5v P-P signal on the A201 pin corresponding to the resistor that had no signal? Check R214, R15, and R216 with meter for correct value. Replace any defective components.

Open between A201 and that resistor or defective CR202 if LMI is bad. Repair i.

No

Check pullup resistors R218, R219, or R229 on that line to insure resistor is good and one side is connected to +5V.

Resistor Yes

Defective? Replace

Swap 7

  • A201 [No
  • A200 | PBs Hnt5
  • A202

Yes

Pg. 6-2

6-15 2600/2600A Domestic V

Page 111

2600A Color Troubleshooting

=

is any coler visible

bee)?

\s care a 2-250 pp signal! Yes Pp ei7

Peels

Replace C211

Is chare a 4.3-3v p-p signal | Yes Replace C10

No

fo tare a 4.50 ‘Yea | Open berwwan TIA Pin 9 > signal on pin 9 and C210. of TA,

Ne

No Is RZZB good?

Yes

Ne Is R21 good? Repair or Replace

Ye

Swapout A201 < 2202

  • A200

Pg. 6-2 6-16 2600/2600A Domestic VCS

Page 112

2600A Color Troubleshooting (Continued)

SES

5 on cathode of CR291. Detective CR291. \s color constantly No Defective rolling (cycling)? D C295, Replace 2 A291

Yes

Swapout Does voitage vary between} Yes Is ¥200 ‘requency Yes pa 7 & 6v on oin 10 of A201 3.3793 MHz? 2) A200 amen R213 is rotated? 3) A202

No Ne

Turn R213 fully clockwise,| ‘Genlace y2t0:

ts mere 6v on anoae of [°S* | detective R213 ar 00 is tnere 6v on anode tu r o0en R200? cetween R7 and A201. RepairioriReglce

Ne

Yes Yes 5.5v on anode of CR201? ls R212 go0d? Defective CR200.

No ay |

Yes

Oven detween -5 & CR29!

6-17 Repair or Replace

Pe. 6-2 2600/2600A Domestic VCS

Page 113

2600A Color Troubleshooting (Continued)

Y290 frequency No, pereceive; Replace 3.5795 = .200? Sia 2) Q200 & Q20

Yes

No No Is RF frequency Can RF Module be Replace RPimodile. 61.25 MHz = .15? tuned prooerly eo

Yes Tune RF module.

No RS good?

Is RF cable good? Replace &

Yes

Reolace RF Module

Pg. 52

ae 2600/2600A Domestic vc:

Page 114

2600A Defective Matrix Troubleshooting Procedure

The pattern may have but all nine blocks are present 5 on screen.

i Pattern is disrupted

if blue or black lines Is blue black grid pattern Swapout Yes

are missing or some dis uted? (See Figure {Yes 1) A200 Beentire marrix portion of the Matrix" “J 4-8 for example bad 2) A202 now on screen? _— faiis to appear on the pattern) 3) A201 TV screen.

  • No No

Is uppe left block on 5. seen defective? | Yes ‘See Figure 6-6 or 4-7 for correct pattern) Pg. Has,

Pg. 6-22 No Li

Are either the middle Swapout Are middle-ieft

lower or the left lower }Yes 1) A202 and lower-level Yes dlock defective? (See 2) A200 blocks now cor- Figure 4-6 or 4-7 for 3) A201 rect (See Figure Correct pattern) 446 or 4-7)

No No

Is uoper-middle pick : block defective?

No Pg. 6-23, Pg. 6-22

Swapout Yes

Is middle-middle Yes: 1) A200 Is middle-middle block defective? 2) A202 block now OK?

  • A20L

No Ne

Is lower-middie Yes block defective?

No! Pg. 6-8 Pg. w45 beg

L

Pg. 6-13

Page 115

2600A Audio Test Pi rocedure

Reinitialize switches. Slide the right difficulty switch to the right.

Is there a clear tone?

}

Use scope or frequency counter to measure frequency at emitter of Q201.

Tone audio to 4.5 MHz by adjusting L201.

H djust to + .06 MHz. Look for stable frequency.

Can unit be adjusted and is sound clear? Yes

Pg. 6-21

Yes

No

Pg. 6-24

6-20 2600/2600A Domestic VCS

Page 116

2600A Audio Test Procedure (Continued)

Are the two

Figure 4-9 alternating on the screen? | ae

oot Do the patterns alternate with the tones? er) Yes

Are both colors and tones consistent each cycle?

Put switches back to initialized positions. Ss Je =! VCS will go through one last cycle before changing to color bar test.

o| Pg, 6-27 Patterns in No

6-21 Swapout

  • A201
  • A200
  • A202 Are patterns now correct? (As in Figure 4-9) Pg. 6-20

Pg. 4-45

2600/2600A Domestic VCS Changed per ECN #0021 1/29/83

Page 117

2600A Defective I/O Lines Troubleshooting Procedure

st

Defective A202 Cap. Connector Oetermine (RAM) Line No. No. Pin No. which lines are Ss ea Pin & detective by 16 229 3202-Pin 3 referring to 13 C228 3202-Pin 2 Figure 4-7. 12 C227 1202-Pin | i 226 = -3203-Pin 4 10 225 1203-Pin 3 9 C228 = 1203-Pin 2 ‘Check the lines 8 C223 3203-Pin | indicated as defective for +5v at 1202 or 1203 (See chart).

‘Swapout Does Diagnostic Se presen Yves 1) A202 Matrix now look Kes on \the!lunets) 2) A200 correct (See just checked? 3) A201 Figure 4-6 or 4-7)?

No No

‘Check the RAM Repair open trace

Ye open Repair Line

(A202) pin. Is +5v =} berween A202 pin shorted 05 oe present there? and the 1203/3203. (Check trace lines).

No

Check trace line(s) from defective pin(s) | Yes R for shorts to ground. sical Are there any shorts?

No

Swapout A202.

Is +5v now Yes present at the A202 pin?

No

Replace the ‘capacitor on that line (see chart).

Does the Diagnostic | No Swapout Matrix screen now ) A200 Jook correct (see Fig. 4-6) 2) A201

Yes <+

A

Pg. 6-2

6-22 2600/2600A Domestic VC

Page 118

2600A Trigger Line Troubleshooting Procedure

<>

Swapout Yes i) zo Does trigger line work | No} R223 or R226 is shorted Reclce Is there +5v at pin 6 of 2) A200 properly now? to +5v. P 3202 (Left Trigger) or 3) A202 3203 (Right Trigger)? Les

No

No Replace Are R226 (Left Trigger) R203 (Right Trigee) defective resistor. good and connect to Sv?

Yes

Check continuity -<tbetween 9-Pins (1202 é 3203) and resistors (R225 and R228).

; No ; Continuity good? Repair Trace

Yes

Open R224, R225 or shorted C216, C217.

Replace

—+

A

Pg. 6-2

6-23 2600/2600A Domestic VC

Page 119

2600A Audio Troubleshooting

Is RF module tuned to | NO 61.25 MHz? Pg. 6-25 (Chane! 3)

Yes

Yes] Is there a defective A201 | Yes| 7 Is oftly one audio or open A201 pin 12 and Repak; tone present? A201 pin 13?

Pg. <= Ta Bg. 6-2

Is there a 2v p-p square wave that alternates} No Parr between two frequencies B 6-25 on pin 13 of A201?

Yes

i Is there a 4.5 MHz, Does square wave signal | Y€5| modulated, 1-2v p-p audiof No Pg. 6-26 appear at C208? signal at C211 (either side)

ike Yes

Fix open trace line between C208 and beat Pin 12/13 of A201. 2) R207

=)

Is there now an alternating audio tone from the TY? Yes,

Pg. 6-2

Page 120

2600A Audio Troubleshooting (Continued)

<>

Can RF module be Is 65 present at the side off No properly tuned? Tune RF module. R206 closest to L201? between +5 & R206 bam

No Yes

Replace RF module. Is there continuity from | No | Repair open between R206 to A201 pin 137 R206 and A201 pin 13.

Swapour A201.

an

Pg. 62

6-25 2600/2600A Domestic VCS

Page 121

2600A Audio Troubleshooting (Continued)

<=>

Fix open trace line between C208 and Pin 12/13 of AzGl.

Ne fs there -5v at one end at L201? Repair race fram -5v so L201.

Yes

Check that L201 is good. (Has continuity and 1s not shorted or cracked.)

Checks Revlace

  • C206, C207
  • L201
  • L202

If audio is still dead, check. » Jtne trace lines around C21 i for opens and snorts.

ls tnere now an alternating audio tone trom the TV?

Pg. 6-24 Pg. 6-2

2600/2600A Domestic VC

Page 122

<> 2600A Cartridge Test Procedure

DTC works, but VCS unit is still suspect.

Plug in customer cartridge, if available. Not Available

Available

Connect, initialize, and turn VCS on with customer's game cartridge.

Does correct video pattern for that game appear? No

Yes

Play game. Does it play OK? Yes

No

Check customer cartridge on known good game. Is it OK? Pg. 6-28

Yes

No

Replace with good cartridge.

AC

Pg. 6-28 Pg. 6-28

Yes

Swapout Does game

  • A201 now operate
  • A200 properly with
  • A202 game cartridge?

No

ip)

Pg. 4-45

6-27 2600/2600A Domestic VCS

Page 123

2600A Burn-In Procedure

< AC >

| Place customer cartridge in game, if available. Otherwise, use other game cartridge.

Run game for 2 hours, minimum. Do not turn off during this period.

Check game's operation.

Is game working properly? End of test sequence.

No

Pg. 6-2

Page 124

< Start >

Put shorting plugs in. Put VCS into Diagnostic Matrix mode. 2600A Paddle Lines Test

Check 3202/3203 for RC Jwavetorm (see Fig. 4-10). | ves ls waveform present on each of the pins shown in chart?

No = No

x 7 Repair open

shown in the chart? Az0 lane 202! wore OS 3203.

Yes

‘Swapout

  • A201
  • A200 =
  • A202

Is there continuity between Ne the 1202 o 1203 Check trace lines and resistors for opens. Realy pin (see chart) and the A201?

Yes

[Repiace cao (c2Z15-Cz18) on the failed line.

Dges RC wavetorm appear| Yes ‘on the appropriate 1202 or 3203 line? (See Chart)

No

‘Swapout

  • A201
  • A200
  • A202

Does Paddle yes

Line now work?

No

Paddle line is open or shorted. i

Repair

T _— Connection Chart

Pin Pin Pin Cap Player A201 3202 203 No T 0 35 = C25 Pg. 6-2 2 ao +S) -— C26 3 3 = $5 C27 4 37 - 9 Cas

$-29 2600/2600A Domestic VCS

Page 125

SECTION 7

GAME CONTROLLERS

OVERVIEW

The following pages contain descriptions, schematics, and test procedures for the four game controllers used with the Video Computer System.

JOYSTICK (X-Y) CONTROLLER Inside each joystick is a small PC board that has five calculator-type keypads mounted on it. Two versions of the PC board exist in current joystick models; see Figure 7-1. Four of the keypads are positioned beneath the stick in a square shaped pattern, and the fifth is located beneath the pushbutton. When the stick is pushed forward, the bottom surface of the stick presses against the forward keypad, causing it to make contact, and complete the circuit that is connected to it. In the same way, pushing the stick back, left and right causes the respective keypad underneath that position to close and complete the circuit.

NOTE: The earliest models of the joystick had five spring-loaded buttons instead of the present configurations. These earlier models cannot be repaired.

Earlier Version Figure 7-1. Joystick (X-Y) Controllers

Page 126

If the stick is pushed forward and to the right at the same time (that is, in a northeastern direction), both the forward and right keypad close simultaneously, which causes the 6532 to see two switch closures happening at once. The result is that the object being controlled on the screen moves diagonally. With the four keypads, $ different directions can be attained. The pushbutton determines whether the keypad beneath it is either open or closed. See Figure 7-2 for Joystick Schematics.

Pin

Fire/Orange o— — —s

  • Up/White , '

—— Down/Blue O———_ Hi?

  • Left/Green 4 D
  • Right/Brown :

Black

Figure 7-2. Joystick Schematic

Page 127

JOYSTICK (X-Y CONTROLLER) CHECK

Equipment Needea

e T.V. set

e@ Known good VCS unit

e@ Combat cartridge

Procedure

  • Check for cosmetic damage.
  • Plug in cartridge and plug controller to he tested into the left olaver oort.
  • Turn on unit and press GAME SELECT until game #18 appears.
  • Press GAME RESET.
  • Push the joystick handle away from vou and the plane should go down.
  • Pull the joystick handle toward you and the plane should go up.
  • Move the joystick right and plane should speed up. Move it left and plane should slow down.
  • Push the Red button and the plane should fire.
  • This completes the (X-Y controller) check.
Page 128

PADDLE CONTROLLER

Each game paddle consists of a | Megohm potentiometer that, when varied, causes different values to be seen and acted upon by the TIA. Also contained in the paddle is a simple spring loaded push-to-make pushbutton switch. There are two game paddles connected to each I/O plug. Figure 7-3 illustrates the paddle controller assembly and Figure 7-4 the paddle controller schematic.

&

Figure 7-3. Paddle Controller

Page 129

"Y" CABLE DUAL 4 CONDUCTOR BUTTON | coiogio contro GREEN 9° S0T 1 VIOLET, oN: PINS

= 5 VOLTS YELLOW PRT

PINS.

BUTTON oo 5 G—_ CONTROL 2 BROWN Ama __Por2 RED Pas a Vee 5 VOLTS GND

Figure 7-4. Paddle Controller Schematic

PADDLE CONTROLLER CHECK

Eguioment Needed

T.V. Set

Known good VCS unit Casino ™ cartridge

Procedure

lL.

2.

3. Check for cosmetic damage.

Plug in cartridge and plug controllers to be tested into the left player port.

Press game reset.

Press the button on one of the controllers. A oair of numbers should appear.

When you turn the knob, one set of numbers should go between 20 and 290 by steps of 20. The numbers should not advance greater than a step of 20.

Repeat steps 3, 4, & 5 for the other controller.

Page 130

DRIVING CONTROLLER

The heart of the driving controller is a switching device that generates a full two-bit gray code for each quarter turn of the controller knob. The output of both the gray

code generator and the pushbutton switch is detected by the 6532, causing the program to respond accordingly. Unlike the non-linear resistive game paddles, the driving controller gives the user precise linear positional control over the complete turning range of the knob. As with the game paddles, there is a simple push-to-make pushbutton switch located on the side of the controller. The driving controller assembly is illustrated in Figure 7-5; the sc: ~atic in Figure 7-6.

Figure 7-5. Driving Controller

Page 131

TRUTH TABLE ] aN PIN 2 PIN is cores ° At 2 are PI + Is cowecz ©9344

  • . 4 BLUE PN2 a = | SAO. cia PINe EE PING 2 SIT Gray CODE a re CLOCKWISE ROTATION X. NO_ CONNECTION 0 GNO |, OCCURS 4 TIMES PER REV. . |. PIM | and 3 ARE INTERNALLY CONMEETED OM coiaao2

Figure 7-6. Driving Controller Schematic

DRIVING CONTROLLER CHECK

Equipment Needed

e T.V. set

@ Known good VCS unit

e Indy 500 cartridge

Procedure

1.

2.

3. Plug in Indy 500 cartridge and plug in driving controller to be tested in left hand port.

Press game reset switch.

Turn controller knob and insure that car turns in the same direction as the knob. Insure that car doesn't skip position or wobble between positions. There should be 16 different positions for the car.

Press down on the knob and lightly wiggle it back and forth. The car should not move at all.

+ Press down on the red button. The car should move forward.

If the controller fails any of the above tests it is defective.

Page 132

KEYBOARD CONTROLLER

The keyboard controller (Figure 7-7) is a 12 button calculator-type switch array that functions like a small computer keyboard. When one of the pushbuttons is pressed, the corresponding set of sense lines is closed, completing the circuit. The closure is detected by the 6532 and appropriate action is taken by the program. Figure 7-8 illustrates the keyboard wiring and Figure 7-9 the keyboard schematic.

. Figure 7-7. Keyboard Controller

Page 133

= VIOLET PINT ; GREEN pee WHITE, pINe Ray PINe si? s2Z. S37 BROWN prt s4 Press ff 6 RED PiInz s7z sag $99 ORANGE mais 0% suf s2f | wventow | leva BLE PING CONTROLLER | <-> CABLE L|

Figure 7-9. Keyboard Schematic

Page 134

KEYBOARD CONTROLLER CHECK

Equipment Needed

e T.V. set

@ Known good VCS unit

e@ Brain Games cartridge

@ One good keyboard controller

Procedure

« Check for cosmetic damage.

  • Plug in Brain Games cartridge and plug the known good keyboard into the right-hand plug.
  • Plug the controller to be tested into the left-hand plug.
  • Press game select until game #19 appears and press game reset.
  • If an audio tone sounds, the controller is defective.
  • Starting with the "lL" key, press the keys in the following order: |, 2, 3, 4, 5, 6, 7,8,9, *, 0, #. Each key should generate a tone lower than the key before it.
  • Test completed.
Page 135

Assy

Bezel Console Console Console Console Final Final Final Final Final Final Final Final

Final

Final Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother

Mother SECTION 8&

CX2600 DOMESTIC (M/N) VCS

Part No.

CA010873 88-1004 C010307-01 011925 CA010869 C016353 CA010112 CA010800 CA012758-01 CA012759-03 CA012760-06 CA012994-03 CA014034

CA018200-01

CA018201-01 14-5101 14-5102 14-5103 14-5123 14-5182 14-5183 14-5221 14-5243 14-5270 14-5332 14-5471 14-5472 14-5473 14-5681 14-5682 14-5912 19-411504 21-101104M 2A-008 2A-018 2B-004

2B-007 PARTS LIST

Description

Bezel Assy Rubber Feet Console Top Console Base Console Base Assy AC Power Adaptor TV Switch Box CX2600 VCS Keyboard Controller Driving Controller Paddle Controller X-Y Controller AC Power Adaptor

AC Power Adaptor

TV Switch Box Resistor 1/4W 100 Ohm Resistor 1/4W 1K Resistor 1/4W 10K Resistor 1/4W 12K Resistor 1/4W 1800 Ohm Resistor 1/4W 18K Resistor 1/4W 220 Ohm Resistor 1/4W 24K Resistor 1/4W 27 Ohm Resistor 1/4W 3300 Ohm Resistor 1/4W 470 Ohm Resistor 1/4W 4700 Ohm Resistor 1/4W 47K Resistor 1/4W 680 Ohm Resistor 1/4W 6800 Ohm Resistor 1/4W 9100 Ohm Resistor Variable 500K Cap. Mylar Dipped .luF (1!00V) Cap. Ceramic Disc 47pF (50V) Cap. Ceramic Disc 22pF (50V) Cap. Ceramic Disc 220pF (50V)

Cap. Ceramic Disc. 01uF (50V)

8-1 Locator

Not Packaged Not Packaged Not packaged Packaged Packaged Packaged Packaged Packaged (Alternate listed) Packaged (Alternate for P/N CA014034) Packaged (CX262 Pack) R202,205 R208,212,214 R225,226,234 R222 R203,216,227-321 R209,233 R204 R206,217,223 R200 R218-221 R201 R207 ,232 R224 R213 R215 R210 R211 C204 C211,212 C213 C236,237 (Alternate for P/N C014180-05) C€200,202,205,208, 214,223-227,239,240

2600/2600A Domestic VCS

Page 136

Assy

Mother

Mother Mother Mother Mother Mother

Mother

Mother Mother Mother Mother Mother

Mother Mother Mother Mother

Mother

Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother

Mother Mother Mother Mother Mother

Mother Mother Mother Mother Part No.

2B-008

2B-009 2C-001 31-1N914 33-2N3906 34-2N3563

34-MPS3563

79-5918 CA010434 CA010808 CA018263 010177

C010314 C010336 C010444 C010448

010727

010745 010750 010776 C010806 010812 010816 010821 010822 010823 010887 C012776 C014180-05

C0143 53 C0143 84 C014386-08 C014386-09 C015510

016035 017654 C018991 CA010434 CX2600 DOMESTIC (M/N) VCS

PARTS LIST (Continued)

Description

Cap. Ceramic Disc .001uF (50V)

Cap. Ceramic Disc 150pF (50V) Cap. Ceramic Disc. 1uF (50V) Diode 1N914 Transistor 2N3906 Transistor 2N3563

Transistor MPS3563

Jack CX2600 PC Board Cartridge Socket Assy Zener Diode/Axial Wrap Assy Crystal 3.579575 Mhz

Socket Cartridge Cap. Electrolytic 4.7uF (35V) IC TIA Socket Controller (9 Pin)

Socket Controller (9 Pin)

IC CPU (6507) IC RAM (6532) Dust Cover Socket Connector (12/24) Pad Cartridge Socket IC Hex Buffer (4050B) Cap. Polystyrene 820pF (50V) Inductor 2uF Inductor 12 1/2 Turn Socket Assy (AID) Cable Ribbon (12 conductor) Cap. Axial 200pF (50V)

Cap. Epoxy Dipped .068uF (100V) Ferrite Bead Socket IC (28 Pin) Socket IC (40 Pin) Crystal 3.579575 Mhz

Rivet Diode Zener 1N4736 (6.2V) Transistor 2N3906 CX2600 PC Board (MOTHER)

8-2 Locator

€203,209,222,228- 235,238 C221 €210,219,220 CR200,201 200,201 Q202 (Alternate Listed) Q202 (Alternate for P/N 34-2N3563) 3204

3200

X200 (Alternate Listed)

C201 A201 J202,203 (Alternate Listed) J202,203 (Alternate for P/N C010448) A200 A202

3200

A203 206,207 L202 L201

C236,237 (Alternate listed) C215-218 200,203 A200 A201,202 X200 (Alternate for P/N CO10177)

CR202,203 200,201

2600/2600A Domestic VCS

Page 137

Assy

Mother Mother Mother Paddle Paddle Paddle Paddle Paddle Paddle Paddle Paddle Paddle Paddle Paddle Paddle Paddle Paddle Paddle Switch Switch Switch Switch Switch Switch Switch

Switch

Switch Switch Switch Switch

Switch

Switch

Switch Switch Switch Switch Switch Switch Part No.

CA010793 CA010808 CA018263 81-4004 C010416 010417 010457 C010464 010737 010738 010739 C010810 010970 C012766 CA010837 CA010933 CA010953-03 CA011620-01 13-5680 21-101224M 2B-007 78-06019 79-5903 C010301-05 010373

010388

010813 010820 C011695 C012241

012242

C0143438

C014372 C014373 C014778-03 C017294 017297 019025 CX2600 DOMESTIC (M/N) VCS

PARTS LIST (Continued)

Description

Electronic Module Assy Cartridge Socket Assy Zener Diode/Axial Wrap Assy Speed Clip Fastener Nut Lockwasher Knob Resistor Variable 1 Meg Top Cover Bottom Cover Fire Button Cable Y Control Sleeve Paddle Label Control Knob Assy Control Cable Assy Paddle Control Assy Switch Resistor 2W 680 Ohm Cap. Poly Film .22uF (100V) Cap. Ceramic Disc .0luF (50V) Heat Sink Socket Phono Jumper (11 AWG) Switch Slide

Switch DPST - Spring Return

Switch Dust Cover Inductor 15uH Heat Sink Switch SPDT

Switch SPDT

Regulator 78M05 (TO-220)

Cap. Electrolytic 4.7uF (35V) Cap. Elect Axial 2200uF (16V) Socket (12 Pin in-line) 3 Switch Static Strip 2 Switch Static Strip Switch Slide Locator

3200 CR202, 203

R101 (Ch 3 version) C103,104 €101,102 (Ch 3 version) 3102

$101-104 (Alternate listed) $105,106 (Alternate listed)

L101,102 (Ch 2-3 version) $107 (Alternate listed)

$107 (Alternate for P/N C012241) listed) Alol

C105 C106 J101

S101-104 (Alternate for P/N C010373)

2600/2600A Domestic VCS Changed per ECN #0021 1/799124

Page 138

Assy

Switch

Switch

Switch

Switch

X-Y Cntl X-Y Cntl X-Y Cntl CX2600 DOMESTIC (M/N) VCS

Part No.

019026

CA012174

CA012175

CA012233

010726 C012107-02 C012108-02 012109 C012110 C012114 C012116 C012951 CA015396 CA016741 PARTS LIST (Continued)

Description Locator

Switch DPST $105,106 (Alternate for P/N C010388) RF Module Assy 5 Pin (Ch 2-3 version) RF Module Assy 3 Pin (Ch 3 version) PC Board Assy (Switch)

Cable Top Cover Bottom Case Boot Retainer Ring Fire Button Handle Spring PC Board (Two-Edged Connection) PC Board (Single-Edge Connection)

Page 139

Assy

Bezel Bezel Bezel Console Console Console Console

Console Fina! Final Final Final Final Final Final

Final Final Final

Final Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother Mother CX2600A DOMESTIC (M/N) VCS

Part No.

015572 C015901 CA015908-01 88-1004 015570 C016398 C016398-01

CA015909-01 C016353 CA010112 CA012758-01 CA0127 59-03 CA012760-06 CA012994-03 CA014034

CA015799 CA015907 CA018200-01

CA018201-01 14-5102 14-5103 14-5114 14-5153 14-5182 14-5183 14-5221 14-5222 14-5241 14-5243 14-5273 14-5332 14-5472 14-5473 14-5474 14-5682 14-5821 14-5910 14-5912 19-411504 21-101104 21-101224M 2A-003 PARTS LIST

Description

Bezel Bezel Label Bezel Assy Rubber Feet Console Top Console Base Console Base

Console Base Assy AC Power Adaptor TV Switch Box Keyboard Controller Driving Controller Paddle Controller X-Y Controller AC Power Adaptor

CX2600A VCS CX2600A VCS AC Power Adaptor

TV Switch Box Resistor 1/4W 1K Resistor 1/4W 10K Resistor 1/4W 110K Resistor 1/4W 15K Resistor 1/4W 1.8K Resistor 1/4W 18K Resistor 14W 220 Ohm Resistor 1/4W 2.2K Resistor 1/4W 240 Ohm Resistor 1/4W 24K Resistor 1/4W 27K Resistor 1/4W 3300 Ohm Resistor 1/4W 4.7K Resistor 1/4W 47 Ohm Resistor 1/4W 470K Resistor 1/4W 6800 Ohm Resistor 1/4W 820 Ohm Resistor 1/4W 91 Ohm Resistor 1/4W 9100 Ohm Resistor Variable 500K Cap. Poly Film .luF (100V) Cap. Poly Film .22uF (100V) Cap. Ceramic Disc 10pF (50V) Locator

(Alternate listed) (Alternate for P/N C016398)

(Not Packaged) (Not Packaged) (Packaged) (Packaged) (Packaged) (Packaged) Packaged (Alternate listed) (Packaged) (Not packaged) Packaged (Alternate for P/N CA014034) Packaged (CX262 Pack) R202,206,21 1,228 R223,226,229,230 R216 R222 R209 R207 R204,224,225,232 R203 R205 R217,227 R214 R218,220 R201,212,219,221 R215 R233 R210 R234 R231 R208 R213 C241 C204 C202 (Alternate listed)

2600/2600A Domestic VCS

Page 140

Assy

Mother Mother

Mother

Mother

Mother

Mother

Mother

Mother Mother Mother Mother Mother Mother

Mother Mother Mother Mother

Mother

Mother Mother Mother Mother Mother Mother Mother Mother Mother

Mother

Mother

Mother CX2600A DOMESTIC (M/N) VCS

Part No.

2A-008 2A-018

2B-003

2B-007

2B-008

2B-009

2C-001

31-I1N914 34-2N3563 79-5903 79-5918 A003647 010177

C010373 C010388 C010444 C010448

010727

C010745 010750 010776 C010812 C010813 C010821 010823 012241 C014179-01

C014179-03

C014179-05

C014180-04 PARTS LIST (Continued)

Description

Cap. Ceramic Disc 47pF (50V) Cap. Ceramic Axial 22pF (50V)

Cap. Ceramic Disc 470pF (50V)

Cap. Ceramic Disc .01uF (50V)

Cap. Ceramic Disc .001uF (50V)

Cap. Ceramic Disc 1 50pF (50V)

Cap. Ceramic Disc .l uF (50V)

Diode IN914 Transistor 2N3563 Connector Phono Jack Connector Jack (3.5mm) RF Cable Assy Crystal 3.579575 Mhz

Switch Slide (DPDT) Switch Slide (DP Spring Return) IC TIA Socket Controller (9 Pin)

Socket Controller (9 Pin)

IC MPU (6507) IC (6532) Dust Cover Socket Pad Cartridge Socket Dust Cover Cap. Polystyrene 820pF (50V) Inductor Variable 0.85-1.2uH Switch Slide (PCB) Cap. Ceramic Axial 22pF (50V)

Cap. Ceramic Axial 10pF (50V)

Cap. Ceramic Axial 47pF (50V)

Cap. Ceramic Axial 150pF (50V)

8-6 Locator

209,210 C211 (Alternate listed) C216,217 (Alternate listed) C203,205,21 2,236, 237,240,244 (Alternate listed) C213,223-235 (Alternate listed) C215 (Alternate listed) C200,208,222,238, 239,245 (Alternate listed) CR200-203 Q202 3204 3201

X200 (Alternate for P/N C015510) $201,204 $202,203 A201 J202,203 (Alternate listed) 202,203 (Alternate for P/N C010448) A200 A202 3200 (Part of) 3200 (Part of) Used on Switches 206,207 L201 §200,205,206 C211 (Alternate for P/N 2A-018) €202 (Alternate for P/N 2A-003) 209,210 (Alternate for P/N 2A-008) C215 (Alternate for P/N 2B-009)

2600/2600A Domestic VCS

Page 141

Assy

Mother

Mother

Mother

Mother

Mother

Mother Mother Mother Mother Mother Mother Mother

Mother

Mother Mother Mother Mother Mother Mother Mother

Mother Mother Mother Mother Mother Mother Mother Mother Paddle Paddle Paddle Paddle Paddle CX2600A DOMESTIC (M/N) VCS

PARTS LIST (Continued)

Part No.

C014180-07

C014181-01

C014181-02

C014181-03

014348

014353 C014369 014373 C014384 C014386-08 C014386-09 C015510

C015519

015573 C015574 015575 015752 015902 017297 017549

C018991 C019748 CA011824 CA012174 CA015796 CAO15911 CA015913-01 CA018263 81-4004 CO010416 C010417 010457 010464 Description

Cap. Ceramic Axial 470pF (50V)

Cap. Ceramic Axial .001uF (25V)

Cap. Ceramic Axial .01uF (25V)

Cap. Ceramic Axial .luf (25V)

Voltage Regulator 78M05 (5V)

Cap. Epoxy Dipped .068uF (100V) Cap. Elec 4.7uF (35V) Cap. Elec 2200uF (16V) Inductor Ferrite Bead Socket IC (28 Pin) Socket IC (40 Pin) Crystal 3.579575 Mhz

PC Board

Socket Cartridge Shield Top Shield Bottom Inductor 1.8uH Connector 12/14 2 Switch Static Strip Switch Slide (PCB)

Transistor 2N3906 IC Timer (555) Dust Cover Assy RF Module Socket Assy (Cartridge) CX2600A PC Board Assy PCB/Shield Assy Zener Diode/Axial Wrap Assy Speed Clip Fastener Nut Lockwasher Knob Resistor Variable 1 Meg Locator

C216,217 (Alternate for P/N 2B-003) C213,223-235 (Alternate for P/N 2B-008) €203,205,21 2,236, 237,240,244 (Alternate for P/N 2B-007) C200,208,222,238, 239,242,245 (Alternate for P/N 2C-001) A203

C218-221 C214 C243 L200,203-205 XA200 XA201,202 X200 (Alternate listed) (Use Rev 16 or above) J200 (Part of)

L202 3200 (Part of)

200,205,206, (Alternate for P/N C012241) 200,201 A205

5 Pin Version 3200

Changed per ECN #0021 1/99/23

Page 142

CX2600A DOMESTIC (M/N) VCS

PARTS LIST (Continued)

Assy Part No. Description Locator

Paddle 010737 Cover Top Paddle 010738 Cover Bottom Paddle 010739 Fire Button Paddle 010810 Cable Y Control

Paddle 010970 Sleeve

Paddle 012766 Label Paddle

Paddle CA010837 Control Knob Assy Paddle CA010933 Control Cable Assy Paddle CA010953-03 Paddle Control Assy Paddle CA011620-01 = Switch X-Y Cntl 010726 Cable X-Y Cntl C012107-02 Cover Top X-Y Cntl C012108-02 Case Bottom X-Y Cntl 012109 Boot X-Y Cntl 012110 Retainer Ring X-Y Cntl CO12114 Fire Button X-Y Cntl C012116 Handle X-Y Cntl C012951 Spring @ X-Y Cntl CA015396 PC Board (Two-Edged Connection) @ X-Y Cntl CA016741 PC Board (Single-Edge Connection)

Page 143

SECTION 6

INDEX

AUDIO TONES

BATTERY ELIMINATOR

BLOCK DIAGRAM

COLOR BAR TEST

CONSOLE

DEFECTIVE RAM PROCEDURES

DIAGNOSTIC FLOWCHART

DIAGNOSTIC MATRIX

DIAGNOSTIC MATRIX TEST

DISPLAY, NO

DRIVING CONTROLLER

GAME PADDLE

GRAY BAR TEST

JOYSTICK

KEYBOARD CONTROLLER

MOTHER BOARD

MPU

OPTION SWITCHES

PADDLE CONTROL LINES

PADDLE CONTROLLER

PADDLE LINES TEST

PARTS LIST

POWER SUPPLY

RAM, DEFECTIVE PROCEDURES

RAM, 1/0

RF CABLE

RF MODULE

RIBBON CABLE

STATIC MODIFICATIONS 3-12, 3A-9, 3C-9

1-2

1-4

3-10, 3A-4, 3C-4

1-1

3A-1, 3C-1

3-3, Acl

3-12

3A-7, 3C-7

3A-3

4-8

4-5

3-11, 3A-5, 3C-5

4-2

4-11

1-2, 2-4, 2-5

1-2

1-2

3-5

4-5

3A-25, 3C-20

5-1

1-2, 2-4, 2-5

3A-1, 3C-1

1-2

1-2

1-2

1-2

3-3

NTSC

Page 144

SECTION 7 o

TECHNICAL TIPS

TECH TIP #1

Green J200

On early production 2600's the J200 is green. We found that it is a very unreliable connector after many insertions. This appears to you as a game that sometimes does not work with a cartridge. Replace the connector.

TECH TIP #2

Audio Failures

On Audio Failures the primary suspects are the two polystyrene caps C206/C207. By putting pressure on the sound caps the audio may come on again. Always replace both caps when you replace one.

TECH TIP #3

Kludge

In some of the early production games you notice a inductor and cap over C201 & R206. This was to cure a problem on a cartridge then, but is now no longer needed. Cut the inductor and cap out being careful not to cut the R206 lead.

TECH TIP #4

Molex Sockets

Chip sockets made by Molex have a low retention value in some cases. This may cause an intermittent color or graphics problem. All sockets with insertion aids should have the insertion aid removed and the chip reinserted.

T= NTSC

Page 145

TECH TIP #5

Floating Ground on 2600

If the ground signal has a lot of noise on it (approx. 1 v.) check continuity on pins 3, 6, and 10 on the J101. ss

TECH TIP #6

Left Paddle Failure

Early production 2600 mother boards (Rev 8 and lower) had an artwork error which was corrected by placing a dot over the trace. This insulates the trace from the casting and should always be on the board. The dot is located under the J200 upper left corner, and the trace should be completely covered.

TECH TIP #7

Indy 500

If a unit works on everything except Indy 500 then pin 23 of the A202 is probably shorted to a data line.

TECH TIP #8

Power Jacks

All power jacks should be tested for a snug fit. When the game is on, lightly move power plug in a small circle, if the picture goes off, replace the jack with a new one.

TECH TIP #9

9-Pins

Check all 9-Pin connectors (J202, J203) for pushed or broken pins. Replace all showing problems.

fs2) NTSC

Page 146

TECH TIP #10

  • R-220

Check that R220 is properly soldered. If they aren't, they will cause intermittent gray bar problems. i

TECH TIP #11

Solder Check

Check solder on the following components: C210, C211, C203, C220, C212, C208, and C209. Long miscues on these caps prevented them from being soldered properly, causing intermittent problems on the board.

TECH TIP #12

Hex Buffers

The 4050 (A203) on the 2600 should be one of the first things checked for any of the following problems: any trigger problem, no Sync., lose of lum lines. This is the reason for a high percentage of returns.

TECH TIP #13

J201 and J101 on the 2600

Both of these connectors should be checked for a good, secure fit.

TECH TIP #14

Crooked Switches

Inspect switches on 2600 switchboard to insure that they set flat and perpendicular to the board. Reset all switches which are not.

13 NTSC

Page 147

TECH TIP #15 .

L200 and Chicklets on 2600/2600A

Be sure when assembling the mother board into the casting that the L200 and chicklets are back under the shroud of the casting.

TECH TIP #16

L201

Make sure the L201 core has a snug fit or else when 4.5 MHz is set, the core can slip in handling. Also, some L201 cores be frozen or cracked in the jacket. Replacement is necessary only if the audio carrier frequency cannot be adjusted to 4.5 MHz.

TECH TIP #17

Reassembly

When assembling the 2600 mother board into casting make sure C220 and C239 are pushed away from J200 shroud.

TECH TIP #18

Excess Lead Length

Check lead length on model 2600 Taiwan games. Trim excessive lead length

on the bottom of the mother board to avoid shorting on casting.

TECH TIP #19

Regulator

On early production 2600 units with standup regulator and heatsink assemblies, inspect for hairline fractures between the regulator and the switchboard. Also insure that on early domestically produced units the regulator is firmly secured to the heatsink by a tinnerman clip.

7-4 NTSC

Page 148

} Consumer Product Service

Manager of Tehnical Support

ATARI FIELD CHANGE ORDER number

MODEL: 2600A ATARI Video Computer System DATE:

PRIORITY LEVEL:

Mandatory on all 2600As received for service that have 12 volt capacitors in either C241 or C242. Replace all 12V capacitors at C241 and C242 even if no symptoms of failure are apparent.

DIFFICULTY REPORTING:

If you have any problems or questions concerning the implementation of this Field Change Order, contact the ATARI Tech Line Specialist.

Inside California (800) 672-1466

Outside California (800) 538-1535

(Go ee Commencanere Comeney 102192 (3/82)

Page 149

y) Consumer Product Service

Manager of Tehnical Support

ATARI FIELD CHANGE ORDER number 1A _ MODEL:2600A ATARI Video Computer System [ DATE: July 19, 1982 | '

SUBJECT:

Changing 12V radial lead capacitors at C241 and C242.

DESCRIPTION:

Some capacitors for these locations are not rated at an acceptable voltage. The incorrect capacitors are 12 volt radial lead type (see Figure 1). An easy way to identify a problem at C241 or C242 is to look at the screen with the diagnostic cartridge running COLOR BAR. The color is very grainy with faint vertical bars. (COLOR BARS look like COLOR SQUARES.)

Figure 1. Incorrect Capacitor

PARTS: OLD REPLACE PART WITH PART LOCATION NUMBER NUMBER DESCRIPTION

C241 2C-001 21-101104 -luf Axial Lead Polycap - 100v

C242 2C-001 CO14181-03 -luf Axial Lead Ceramic - 25v

INSTALLATION PROCEDURES:

Desolder and remove 2C-001 from C241. Insert and solder 21-101104 into C241.

Desolder and remove 2C-001 from C242. Insert and solder C014181-03 into C242.

TESTING PROCEDURES:

Use standard testing procedures as outlined in the 2600/2600A Field Service Manual! (C018040).

(Qa rene comnsnconenn Comsery 10192 (3/82)

Page 150

Consumer Product Service

Manager of Tehnical Support

ATARI TECH TIP a a

MODEL: CX2800 DATE: 11/17/82

SUBJECT:

Blanking Resistor

DESCRIPTION:

The Rev. 4 CX2800 PCB has an 820 Ohm resistor soldered across pins 6 and 9 of U2 (TIA) on the soldered side (bottom). This resistor improves the game color and must not be removed. Rev. 5 and above CX2800 PCB have this resistor incorporated in their design.

DIFFICULTY REPORTING:

If you need further clarification concerning this Tech Tip, call the ATARI Tech-Line Specialist.

Inside California (800) 672-1466

Outside California (800) 538-1535

QA verer Commurncetans Comceny 10191 (3/82)

Page 151

ATARI

Consumer Product Service

Manager of Tehnical Support

TECH TIP

number 3

MODEL: CX2200 DATE: 11/17/32

SUBJECT:

Switchcaps

DESCRIPTION:

to correct this problem.

DIFFICULTY REPORTING:

Specialist:

Inside California (800) 672-1466

Outside California (800) 538-1535

Light Pipe If at power-up two switches are activated at the same time (indicated by both the Joystick and Paddle, or Novice and Expert LED's "on" at the same time), you must shorten the switchcap hand ends with sand paper, to eliminate binding.

If the switchcaps seem to be binding when activated on Rev. 4 PCBs, tilt the momentary switches (S2-S9) toward the player port side of the board so that there is a -030 inch gap between the board and the leading edge of the switch bottom (a manual approximation is usually successful). Some Rev. 4 PCB's have a shim glued to the PCB

If you need further clarification concerning this Tech Tip, call the ATARI Tech-Line

a

a rey

(A vere: conmancanene Comeary 1¢191 (3/82)

Page 152

Consumer Product Service

Manager of Tehnical Support

ATARI TECH TIP ounber__ 4

MODEL: 2600A BATE? UW/17/82

SUBJECT:

Blanking Resistor

DESCRIPTION:

Some 2600A PCBs have an 820 1/4 W 5% resistor (P/N 14-5821) installed on the solder side (bottom). The resistor is located between pins 6 and 9 of A201 (TIA) and improves the color reproduction of the unit.

The resistor may be added to existing 2600A units at your discretion and the customer's expense. The addition will result in improved color saturation.

Rev. 16 PCBs and above will have the resistor incorporated into their design.

DIFFICULTY REPORTING:

If you need further clarification concerning this Tech Tip, call the ATARI Tech-Line Specialist:

Inside California (800) 672-1466

Outside California (800) 538-1535

(QA weomer Commurncoera Comsary 16191 (3/82)

Page 153

Consumer Product Service

Manager of: Tehnical Support

ATARI TECH TIP number.

mopeL: ©%2800 pate: 11/17/82

SUBJECT:

Switch Shorting

DESCRIPTION:

The Rev. 4 CX2800 PCB switch SI (On/Off) has a metal standoff that may short to the trace beneath the switch. To prevent shorting, place a small piece of insulating tape on the board beneath the switch. PCB to Rev. 4 and above have the traces rerouted.

DIFFICULTY REPORTING;

If you need further clarification concerning this Tech Tip, call the ATARI Tech-Line Specialist:

Inside California (300) 672-1466

Outside California (800) 538-1535

Metal Standoff ~ switcs Eee te

16191 (3/82) Qi vere commons conser,

Page 154

Consumer Product Service

AK VCS Manager of Technical Support

ATARI SERVICE BULLETIN

MODEL: 2600 Video Computer System DATE:DEC 9, 1981

PROBLEM Compatability problems between the cable and connectors linking 2600 Mother Board to the switch board.

CAUSE Two types of 12-conductor cable assemblies have been used on Model 2600 units:

° A flat-wire type cable, with female connector (see Figure 8-1) which plugs into a male 12-pin in-line connector on the switch board.

A ribbon cable with a male connector which plugs into a female, 12-pin in-line socket on the switch board.

AM Figure 8-l. Flat-wire Type Cable

SOLUTION When a defect is found in the flat-wire type cable assembly or its male connector on the switch board, the flat-wire cable assembly should be replaced with the ribbon cable assembly (part number CO12776) and the 12-pin male switch board connector should be replaced with the 12-pin female switch board socket (part number CO14778-03).

8-1 1174 (12/81)

Page 155

Consumer Product Service

M. VCS Manager of Technical Support

ATARY SERVICE BULLETIN

MODEL: 2600A Video Computer System DATE: February V7, 1982

PROBLEM

-- RF Interference that does not clear up using normal adjustment methods.

-- A series of lines and bright grid distortions on the screen accompanied by a loud hum on the audio carrier even when the audio and video are properly adjusted.

The above problems may temporarily disappear when the unit is turned off for a few minutes and then turned on again.

CAUSE

These 2600A problems have been diagnosed by Atari as being caused by a leaking or defective C241 (.1 microfarad) and/or C242 (.1 microfarad) located between the power jack and voltage regulator.

SOLUTION

Replace the defective components with ones from your kit. Make certain the replacement components are rated at a value 50V or greater.

1¢174 (12/81)

Page 156

Consumer Product Service

M. VCS Manager of Technical Support

ATARI SERVICE BULLETIN

MODEL: 2600 Video Computer System

DATE: February 18, 1982

PROBLEM

Damage to Hex Buffer, and other components

CAUSE

Static discharge

SOLUTION

FIELD SERVICE MANUAL DOMESTIC MODEL 2600/2600A.)

8, 1982.

Assembly. To provide protection from static discharge a Zener diode must be placed between the trigger lines and ground. Also, static strips must be placed on the switches of the switchboard. (Refer to pages 3-3 thru 3-5 of your ATARI VIDEO COMPUTER

The part number for the Zener Diode/Axial Cap. Assembly is CA018263 and can be ordered (at no charge to you) from Sales Order Processing, Sunnyvale, after March

You should have the static strips (Part Numbers C017294 and C017297) in current parts inventory. If you do not, please order them when you order the Zener/Axial

10174 (12/81)

Page 157

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 158

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 159

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.