CATHODE RAY TOMES

Asteroids Caberat TM-155 1st Printing

Asteroids (rev 4) (Atari, 1979) · Technical Manual · 52 pages · 44 sections · original scan

Page 1
Scan of page 1

This page is a drawing, shown as the original scan.

Page 2

GAME SERIAL NUMBER LOCATION

Your-game’s serial number is stamped on.a plate:on the outside-of the game. Q

The same number is also stamped on the chassis of the TV-monitor, onthe Regulator/Audio- PCB andthe Game.PCB.. Please mention-this number whenever calling your distributor for service.

GAME:SERIAL # IDENTIFICATION TAG

Page 3

Operation, Maintenance and Service Manual

Complete with Illustrated Parts Lists

Published by: ATARI INC 1265 Borregas Avenue P. O. Box 427 Sunnyvale, California 94086

Copyright © 1979, 1980 by Atari, Inc. All rights reserved.

No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, cr otherwise copied for ®

public or private use, without permission from the publisher. ATARI

Lithographed inthe U.S.A. 6d Warner Communications Compary (D

Page 4

Table of Contents

1 Location Setup A. New Parts. B. Game Inspection C. Game installation. .

  • Voltage Selection ........
  • Interlock and Power On/Off Switches . D. Self-Test Procedure ..............-. E. GamePlay .......
  • Attract Mode ....
  • Ready-to-Play Mode .
  • PlayMode.........
  • High Score Initial Mode

2 Maintenance and Repair SOODORDRWWwW4

A. Cleaning... 0.0... c cee eee e tenet ee B. Fuse Replacement. . C. Opening the Control Panel

  • Leaf Switch Replacement
  • LED Switch Replacement . TV Monitor Replacement. . Printed-Circuit Board Replacement Fluorescent Tube Replacement . Coin Door Repairs .......... xro™mmp

3 Illustrated Parts Lists Game Operation. ....... 0.0.2 cece eee teen eee

Page 5

Figure 1 Figure 2 Figure 3 Figure 4

Figure 5 Figure 6 Figure 7 Figure 8

Figure 9 Figure 10 Figure 11 Figure 12

Figure 13 Figure 14 Figure 15 Figure 16

Figure 17 Figure 18 Figure 19 Figure 20

Figure 21 Figure 22 Figure 23 List of Illustrations

Overview of Game Installation Requirements . Power Supply .... Interlock and Power Oni ff Switches ...

Location of Self-Test Switch, Volume Control and Option Switches . Self-Test Procedure . ee see . Option Switch Settings : Opening the Control Panel and Replacing Switches .............. 1

TV Monitor Removal. . Game and Regulator/Audio Fluorescent Tube Replacement 7 Removing Coin Mechanism..... 02.0... 00..0 sees e cece eee eee ee 7

Switch and Trip Wire Replacement .. . Coin Door Lamp Replacement... Power Distribution ....... Signal Distribution . .

Illustrated Parts Lists: Cabinet-Mounted Assemblies Control Panel Assembly ......- ccc e cece eee tenets Fluorescent Light Assembly Regulator/Audio PCB Assembly 28

Asteroids Game PCB Assembly ...........0. 00000 e eee ene ees 30 Power Supply Assembly for X-Y Games 34 New Coin Door - 3%

iti

Page 6
NOTE

If reading through this manual does not lead to solving a certain maintenance problem, call Tele-Help™ at the Atari Customer Service office in your geographical area, as shown in one of the two maps below. Order all parts from the California office.

WEST and CENTRAL U.S.A.

Parts for all Atari Customers. Sales and Service

Atari Coin-Op Customer Service 1344 Bordeaux Drive, Sunnyvale, CA 94086 Telex 17-1103 (Monday - Friday, 7:30 - 4:00 pm Pacific Time)

Po From California, Alaska or Hawaii (408) 745-2900

ese From anywhere else in this area toll-free (800) 538-1611

EAST U.S.A.

Sales and Service Only

Atari |nc. New Jersey Customer Service Office Cottontail Lane, Somerset, NJ 08873 Telex 37-9347

(Monday - Friday, 8:30 - 5:00 pm Eastern time)

= From New Jersey (201) 469-5993

From anywhere else in this area ‘toll-free (800) 526-3849

Page 7

A. New Parts

The Asteroids™ game in the cabaret cabinet has four new parts. If you have worked on Atari games in the past, then you should be aware of these important differences. The new parts are: @ Power Supply Assembly. \t covers a wider voltage range than before, has higher reliability, asmaller overall size, and all fuse numbers and fuse amperages are marked directly on the metal chassis. @ Game PCB Circuitry and TV Monitor. Most video games to date have used the raster-scan method of display. This game uses vector generation with X and Y axes to allow greater contrast, a greater number of moving objects on the screen, and lines at any angle to be “drawn” on the screen.

Location Setup

Page 8

XY TV MONITOR

TV MONITOR SHIELD

CONTROL PANEL

ATTRACTION PANEL f | ©. oe, q

COIN DOOR

POWER SUPPLY

POWER ON/OFF SWITCH

Figure 1 Overview of Game Sa GAME SPEAKER

REGULATOR! AUDIO PCB

ACCESS PANEL

Page 9

@ Cabaret Cabinet Design. This more compact cabinet was designed to occupy less than 4 square feet of floor space.

@ New Coin Door. This door will accomodate two or three mechanisms, and up to four coin counters. Its triple-arm locking bar provides added security. For greater ease of access, the selftest switch is now mounted on the door, rather than inside the cabinet. Also, for simpler maintenance the door’s coin mechanisms require no adjustments.

These new parts, as well as all other major parts in the game, are illustrated in Figure 1. Throughout this manual, wherever one of these new parts is mentioned, you will see this symbol in the page margin: oe

B. Game Inspection

This new game is ready to play upon removal from the shipping carton. However, your careful inspection is needed to supply the final touch of quality control. Please follow these steps to help us insure that your new game was delivered to you in good condition.

[donate NOTE ener _| Do not plug the game in yet!

  • Examine the exterior of the game cabinet for dents, chips, or broken parts.
  • Unlock and open the access panel of the cabinet and inspect the interior of the game as follows: a. Check that all plug-in connectors (on the game harness) are firmly seated. Replug any connectors found unplugged. DON’T FORCE CONNECTORS TOGETHER. The conneciors are keyed so they only go on in the proper orientation. A reversed edge connector will damage a PCB! b. Check that all plug-in integrated circuits on the game PCB are firmly seated in their sockets.
WARNING To avoid possibie unpleasant elecirical shock, do not touch internal parts of the TV monitor with your hands or metal objects held in your hands!

c. Note the location of the game’s serial number—it is printed on the special label on the outside of the game cabinet. Verify that the serial numbers also stamped on the Game PCB, Regulator/Audio PCB and TV Monitor are all identical. A drawing of the serial number locations is on the inside front cover of this manual. Please mention this number whenever you call your distributor for service. d. Check all major subassemblies such as the power supply, control panel and TV monitor for secure mounting.

C. Game Installation

Figure 2 Installation Requirements

Power 175 watts Temperature 0 to 38°C (32 to 100°F) Humidity Not over 95% relative Space Required 52x 60 cm (20 3/8 x 23% in) Game Height 140 cm (55 in.)

  • Voltage Selection

Before plugging in your game, make sure that the voltage selection plug on the power supply (see Figure 3) is correct for your location’s line voltage. Check the wire color on the plug and see if it is correct per the list below.

Line Voltage Range Voltage Selection Plug Color 90-110 VAC (100) Violet 105-135 VAC (120) Yellow 200-240 VAC (220) Blue 220-260 VAC (240) Brown

Page 10

Asteroids™ | Cabaret

Figure 3 Power Supply

  • Interlock and Power On/Off @ = If the results of the previous step are satisfac- Switches tory, the interlock switches are operating properly. \f the TV monitor doesn’t go off as oe . . described, check to see if the corresponding in- To minimize the hazard of electrical shock while terlock switch is broken from its mounting or working on the inside of the game cabinet, two inter- stuck in the “on” position. lock switches have been installed (see Figure 4). One is located behind the access panel and one is behind the coin door. These switches remove all AC line power from the game circuitry when a door is opened.

Check for proper operation of the interlock switches by performing the following steps: @ Unlock and open the access panel and the coin door. @ Plug the AC line power cord into an AC outlet. Close the access panel and coin door. @ Set the power on/off switch to the on position. Within 30 seconds the TV monitor should display a picture. @ Slowly open the access panel. The TV monitor picture should disappear when the panel is opened approximately 2.5 cm (1 inch). Close and lock the access panel and repeat this step with the coin door. e

Page 11

SWITCH COVER

SAFETY INTERLOCK

POWER ON/OFF SWITCH

Figure 4 Interlock and Power On/Off Switches

Page 12
  • Part of the self-test procedure includes a D. Self Test Procedure display of the operator-selectable game options. Therefore, we suggest you run the self-test pro- This game will test itself and provide data to cedure anytime you need to change the game’s demonstrate that the game’s circuitry and con- options. trols are operating properly. The data is provided on the TV monitor and the game speaker; no addi- To run the self-test, follow the instructions outtional equipment is necessary. lined in Figure 6.

VOLUME CONTROL

VOLUME INCREASE: TURN CLOCKWISE OPTION SWITCHES (total of 12) “3

Figure 5 Location of Self-Test Switch, Volume Control and Option Switches

Page 13

Figure 6 Self-Test Procedure

RESULTS IF TEST

INSTRUCTION PASSES RESULTS IF TEST FAILS

1.Set self-testTV monitor displaysRAM FA/LURE is indicated by a sequence of from 1 to 6 tones. A low-
switch to ‘on posi-picture as shown infrequency tone js heard for each good RAM chip. A much lower frequency is
tion (see Figure 5).Figure 7.heard for a failing RAM chip. The test stops with the first failing RAM chip.

To restart the sequence, press the Reset pushbutton on the game PCB or set the self-test switch to off, then again to the on position. Identify the bad RAM chip with table below. Example: Three tones, then a tone of much lower frequency indicates failure of RAM chip R4. TONE # RAM CHIP LOCATION D2 E2 M4 RA N4 P4 ROMIPROM FAILURE is indicated by two columns or lines of numbers in the upper left-hand corner of the display. The number in the left column or first line indicates the failing ROM/PROM chip(s). Identify the bad ROM/PROM with table below. The number in the right column or second line indicates the failing data bit of the failing ROM/PROM. Identify the bad bit with the second table below. If more than one bit is failing, the displayed number(s) are hexadecimal combinations of the numbers shown below. Examples:

  • If bits D2 and D3 fail, C is displayed.
  • If bits D2, D3 and D7 fail, 8C is displayed.
  • If bits D4 and D6 fail, 30 is displayed.
  • If bits D1, D3, D5 and D6 fail, 6A is displayed DORoOns

DISPLAYED NO. FAILING ROM/PROM

$NIPSK4, La

2 F2,H1

3FALF2, Ltwu

4 H2, J1

5DIE1Ha, JM2, M1

6 J2, K1

8ctKi, J2reas

DISPLAYED NO. FAILING BIT 1 Do 2 D1 4 D2 8 D3 10 D4 20 D5 40 Dé 80 o7 RAMSEL SIGNAL FAILURE is indicated by a BANK ERROR or PAGE SELECT ERROR message at lower middle of display.

2.Activate all1 PLAYER START1 PLAYER START and/or 2 PLAYER START LEDs not lighted.

control pane! and and 2 PLAYER

coin door switches.START LEDs areHigh-pitched click sound is not heard for any particular switch.

When satisfied with lighted. Hightest, set self-test pitched click for switch to off posi- each activated tion. switch.

N

Page 14

Figure 7 Option Switch Settings To change toggle positions of the switch assemblies, you need not remove the game PCB. The switch, usually colored blue, is easily accessible when the game PCB is mounted in place. When changing the options, verify proper results on the TV monitor display during self-test. A switch toggle in the on position is indicated by a 0 for that switch on the TV monitor display. A switch in the off position is indicated by the number 1.

Toggle Settings of 8-Toggle Switch ‘on Game PCB

87654321

Option

On On On Off off On Off Off English German French Spanish

On 4Ship Game Off 3Ship Game On Center Coin Mech x 1 Center Coin Mech x 2 (Both settings are for left mech, if a 2mech door) Off

On On Of Off On on off

On On Free Play On Off Off On Off Off

Suggested settings are shown in illustration at right. 2Coins* for 1 Right Coin Mech x 1 Right Coin Mech x 4 Right Coin Mech x 5 Right Coin Mech x &

1 Goin* for 2 Plays 4 Coin* for 1 Play CTA. COIN MECH MULTIPLIER (LEFT

MECH OF A 2MECH DOOR)

swiTcH TOGGLE1 RIGKT COIN MECH MULTIPLIER ‘swiTcH TOGGLE 8

Photograph above shows toggles 1, 2, 47 on, and toggles 3 and 8 olf. Play

  • Note: In the U.S. and Germany only, a “coin” is defined as 25¢ or 1 DM. If your game also has $1, 2 DM or 5 DM mechanisms, you must set the center and right coin mechanism factors as per your choice.

Option

All 3 coin mechanisms are Belgian or French 5 Fr/S5 Fr, Swiss or French 1Fr/1 Fr, same denomination; all Toggle Settings of 4-Toggle Switch on Game PCB

4321For Games Having These Coin Doors:
OnOnThai 1 Baht/1 Baht, German 1 DM/1 DM, U.S. 25¢/25¢,

U.S. 25¢/25¢/25¢, Japanese Y100/Y100, Swedish 1 Kr/1 Kr, U.K. 10 P/O P, Australian 20¢/20¢, or Italian 100 L100 L

OffOnGerman 2 DM/1 DM, German 1 DM/5 DM, U.S.

250/250/$1, or U.S. 250/91

OnOffNo coin door is currently designed for this contigura-

tion.

OifOffGerman 1 DM/2 DM/5 DM

register on one coin counter.

Left and center mechanisms are same denomination; right mech is another denomination. Requires two coin counters.

Left mech is one denomination; center and right mech are another denomination. Requires two coin counters.

Left, center and right mechs are 3 different denominations. Requires three coin counters.

Page 15

E. Game Play

Atari’s Asteroids™ game has five possible modes of operation: Attract, Ready-to-Play, Play, High Score Initial, and Self-Test. Self-test is a special mode for checking the game switches and computer functions. You may enter this mode at any time. When entered, all game credits are cancelled.

  • Attract Mode

The attract mode begins when power is applied to the game, after a play or high score initial mode, or after self-test. This mode is continuous and is only interrupted when a coin is inserted and accepted or when in self-test. In this mode, the TV monitor displays two possible pictures. Both pictures have three score values across the top of the screen and a message that states the number of coins for a game. The middle score represents the high score to date. The left score is for player 1. The right score is for player 2.

One picture displays asteroids and an occasional enemy spaceship “floating” across the screen. The second picture displays up to 10 of the highest scores since the game was last powered up or since the last self-test. These two displays alternate every 16 seconds.

  • Ready-to-Play Mode

This mode begins when sufficient coins have been accepted for a one- or two-player game. It ends when the 1 PLAYER START or 2 PLAYER START pushbutton is pressed. When this mode begins, the message PUSH START flashes immediately below the center score at the top of the screen. The displayed pictures are otherwise the same as those shown in the attract mode.

  • Play Mode

The play mode begins when either start pushbutton is pressed. The mode ends when the player's last ship of the game is lost.

If the 1 PLAYER START pushbutton is pressed, the following picture is displayed: the PLAYER 2’s score disappears; the PLAYER 1’s score becomes 00, and the number of ships (3 or 4, depending on the operator's setting) for the game appears below that score. The message PLAYER 1 aiso appears below the high score to date. Two seconds after pressing the 1 PLAYER START button the PLAYER 1 Asteroids™ ‘ Cabaret

message disappears, and the game ship appears at the center of the display. Four large asteroids appear and drift in from the outer edges of the display.

If the 2 PLAYER START pushbutton is pressed, the following picture is displayed: the PLAYER 1 and PLAYER 2 scores become 00, and the number of ships for the game appears below each score. The player 1 score also flashes as the message PLAYER 1 appears below the high score to date. Two seconds after the 2 PLAYER START pushbutton is pressed, the PLAYER 1 message disappears. The game ship for player 1 appears at the center of the display as four large asteroids appear and drift in from the outer edges of the display.

By pressing the LEFT ROTATE and RIGHT ROTATE pushbuttons on the control panel, the Player may aim a spaceship toward any of the asteroids. By pressing the FIRE pushbutton, the player may shoot at the asteroids.

When shot, each large asteroid divides into two medium-sized asteroids and the game adds twenty points to the player's score. Medium-sized asteroids, when shot, divide into two small-sized asteroids, and the player receives fifty points. Smallsized asteroids, when shot, will completely disappear, and the game awards 100 points to the player. When players have shot all asteroids, a new set of large asteroids again appear and drift in from the outer edges of the TV monitor display. At the beginning of the game, four large asteroids appear. At the beginning of the next cycle when large asteroids reappear, there are six, the next time eight, and thereafter ten—to increase player challenge.

At any time during game play, a flying saucer may appear from either side of the display. The game awards players 200 points for shooting a large saucer and 1000 points for a small saucer. (The latter is a smaller target for players, though not any faster moving than the large one. It also shoots more accurately.)

The player's objective in the game is to shoot and destroy as many asteroids as possible before all his or her spaceships are destroyed. A ship is destroyed if an asteroid or saucer smashes into it, or if a flying saucer shoots it. To prevent losing a ship, the player may press the THRUST pushbutton to move out of the path of an asteroid or saucer. As an emergency maneuver, players can press the HYPERSPACE pushbutton: the ship disappears and reappears at a random location on the display—however, possibly right on top of, or in the path of, an asteroid. The ship may also explode on reentry.

The game awards an extra ship each time a player’s score reaches multiples of 10,000; i.e., one

Page 16

Asteroids ™ / Cabaret

ship is awarded at 10,000 points, another ship at 20,000 points, etc.

When the last ship of the game is destroyed, the message GAME OVER appears below the high score. This message remains for 3 seconds before the high score. initial mode begins.

  • High Score Initial Mode At the beginning of the high score initial mode, the player instructions appear at the top of the screen, and A_____ appears at the lower center of the display. Players enter initials one character at a time. By pressing the LEFT ROTATE pushbutton, the displayed character steps through the alphabet from A to Z. By pressing the RIGHT ROTATE pushbutton, the character steps backwards through the alphabet from A to a b/ank, then from Z to A.

Once the game displays the desired letter, players should press the HYPERSPACE pushbutton to record the letter; then an A appears in the next space.

\f players need only two letters for their initials, they should use the blank between Z and A in one of the three locations. Pressing the HYPERSPACE pushbutton a third time will cause the initials and game score to be transferred to the “10 highest scores” lisiing that appears during the attract mode.

Page 17

All games require certain maintenance to keep them in good working order. Clean, properly maintained games will attract players and earn more profits.

The most important maintenance item is running the self-test every time you collect money from the cash box. Just looking at a game will not tell you if light-emitting-diode switches or leaf switches are broken, or if LEDs have burned out. The self-test will inform you of any of these possible problems.

Second, you should regularly clean the outside of the game and the coin mechanisms. In addition, you will need to regularly clean the leaf switch contacts: for details see this chapter.

Maintenance and Repair

Page 18

A. Cleaning

The exterior of the game cabinet and the metal and acrylic surfaces may be cleaned with any nonabrasive household cleaner. If desired, special coin machine cleaners that leave no residue can be obtained from your distributor. Do not dry-wipe any of the acrylic panels, because any dusican scratch the surface and result in fogging the plastic.

B. Fuse Replacement

This game contains six fuses—all on the power supply assembly (not including the TV monitor fuses). Replace fuses only with the same type as listed in Figure 22 of this manual. See the Quadrascan TV monitor manual, TM-151, for the monitor fuse data.

C. Opening the Control Panel

Prior to repairing or replacing any switch on the control panel or prior to removing the TV monitor, unplug the game. Then open the coin door.

Reach through the opening and remove both sets of carriage bolts, wing nuts, split lock washers, and flat washers, located on the underside of the control panel (see Figure 8). Lift up on the control panel and swing it towards you.

To remove LED switch: @ Remove all wires from the faulty switch. @ Turn the switch counterclockwise while holding the black cone-shaped nut on the outside of the control panel. @ instal! a new switch using the reverse procedure. @ Reconnect the hamess wires. COMMON CONTACT LIGHT-EMITTING DIODE (L.E.0.)

G CONTACTS

>~~~ NORMALLY OPEN \ (N.0.) CONTACT NYLON SPACER NORMALLY CLOSED (N.C) CONTACT

LEAF SWITCH

TURN NUT TO REMOVE WHITE BUTTON

Figure 8 Opening the Control Panel and Replacing Switches

Page 19
  • Leaf Switch Replacement
NOTE Adjust switches for a narrow gap. When a switch button is depressed, the resulting wiping action of the contacts provides a self-cleaning feature.

All five of these leaf switches operate on 5 volts at a very low current. Therefore, pitting of these switches would be extremely rare. Probably the only reason that pitting would occur is in very highhumidity locations.

Don’t burnish the switches. Burnishing them removes their plating, thus increasing the corrosion of the contacts. The best method of cleaning the switch contacts is to wipe them with a non-abrasive surface. A business card works very well.

To replace any switch, remove both of its screws with a Phillips-head screwdriver—see Figure 8.

If the white button itself needs to be replaced, turn the stamped nut with a wrench in a counterclockwise direction, as seen from the inside of the control panel. The white ring on the outside of the contro! panel should not spin, due to its design.

  • LED Switch Replacement

The light-emitting diode (LED) switches on the contro! panel have a very low failure rate. In case a switch should ever be suspect, first test it per the description that follows. To replace the switch, refer to Figure 8.

  • Remove the wires from the suspected switch.
  • Set multimeter to ohms scale. Set ohms scale to Rx 1, then zero the meter.
  • Connect multimeter leads to appropriate LED switch contacts (see Figure 8 for designation of switch contacts and meter lead placement).
  • Check contacts (push and release the switch button) for closed and open continuity. 5, If the contacts do not operate sharply or always remain closed or open, then replace the LED switch as outlined in the figure.
Page 20

° |f you should need to remove the Quadrascan X-Y

D. TV Monitor Replace- TV monitor, follow steps 1 thru 6 as listed on this

ment page. Refer to the accompanying Figure 9.

  • Open the control panel as described in Section C, Opening the Control Panel. Be sure the game is unplugged from its wall outlet!
  • Remove the acrylic TY monitor shield by lifting up and sliding out its lower edge. Remove the High volt CAUTION | . TV small 4” plywood panel that acts as a monitor Moniicn Sarath power disconnected Soe peo (it prevents players from flexing Use extreme caution and do not touch fe shield downwards). . elecrical parts or the TV yoke area with 3. Carefully remove the black cardboard bezel: it your hands or with metal objects in your lies on top of the wood cleats and is attached hands! with staples. If you drop the TV monitor and the pic- 4. Open the rear access panel and unplug the ture tube breaks, it will implode! Shat- 12-pin TV monitor harness connector. tered glass and the yoke can fly 6 feet or 5 more from the implosion. Use care when ° replacing any TV monitor. Remove the four screws that hold down the metal TV chassis.
  • Carefully tilt and lift the TV monitor chassis out the top opening of the game.

Figure 9 TV Monitor Removal

Page 21

E. Printed-Circuit Board Replacement

You may wish to remove the game printed-circuit board (PCB) or the Regulator/Audio PCB for service or inspection. To do this, refer to Figure 10 and proceed as follows:

1. 2. Open the rear access panel. Locate the securing screw that holds down the PCB in its slots, and remove. \f you are removing the game board, first remove the two tie wraps that fasten the edge connector to the game PCB. Then unplug the edge connector on the game PGB. If you are removing the Reguiator/Audio PCB, simply disconnect the three small harness connectors on this board. Carefully slide either PCB straight out of its gray plastic slots. Be careful not to twist the board, as this may loosen connections or components. Replace or repair as required. Reinstall the PCB, making sure that the connectors are properly plugged in. Note that they are keyed to fit on only one way, so if they don’t slip on easily, don’t force them! A reversed connector will probably damage your game and will void the warranty. Replace the securing screw in the PCB. Reinstall the tie wraps used to secure the edge connectors to the PCB. Close and lock the rear access panel. Check that the operation of the game is correct by performing the self-test. This is especially

important with any game when you replace a PCB. Normally the only adjustments on this game are option switch changes (made on the 4-or 8-toggle DIP switches). Unless you are a qualified technician, do not turn any of the knobs near the game PCB’s edge connector. Also do not turn the small knob on the Regulator/Audio PCB,

Figure 10 REGULATOR! AUDIO PCB

ASTEROIDS™

eo GAME PCB

Game and Regulator/Audio PCB Replacement

Page 22

Figure 11 Fluorescent Tube Replacement

F. Fluorescent Tube Replacement font ‘Graphics attraction panel low ine Be cedure (see Figure 11).

A— CAUTION A

\f you drop a fluorescent tube and it breaks, it will implode! Shattered glass can fly 6 feet or more from the implosion. Use care when replacing any fluorescent tube.

  • Open the goin door. Remove the two Y-shaped connectors from the ends of the fluorescent tube. Now carefully remove the tube from its clamps by pulling it towards you.
  • Replace with a new tube. Do not snap the tube in vigorously—you may break it, causing an implosion!
  • Close the coin door and lock it.
Page 23

G. Coin Door Repairs

The new Atari coin door has been totally redesigned, as described on page 3 of this manual. For ease of maintenance, the coin door mechanisms require no adjustments. For plastic mechs, use only hot soapy water to clean them: boiling water is not needed nor even recommended, as this would soften the plastic.

COIN MECHANISM To remove any mechanisms, or to replace the small lamps, switches or trip wires, follow the illustrations and instructions given in Figures 12 through

  • To obtain part numbers for ordering purposes, refer to the detailed exploded drawing of the coin door and parts list in Figure 23.

STUDS

@ Open coin door. To clean or replace a mechanism, locate the black spring clip above the coin switch. Pull this clip towards you, then swivel it up 90°. @ Push the mechanism towards the right, then pull it out. @ When reinserting the mechanism, be certain that no wires get caught up in it. Align the mechanism between the top and bottom pairs of vertical tabs in the inner door panel. @ Push the part of the mechanism closest to you to the left, so both of its round studs slip into the curved notches on the inlet and return chutes. © Turn the black spring clip down again to secure the mechanism in place.

SPRING CLIP

Figure 12 Removing Coin Mechanism

Page 24

SWITCH COVER

QUICK-DISCONNECT WIRES Va »

QUICK-DISCONNECT WIRES Remove the plastic switch cover by squeezing together Its two prongs (just underneath the switch). Tilt the bottom edge of the cover out to the right while pulling down on it. Unplug the quick-disconnect wires on the switch and lockout coil. Use a longer-style 4" socket wrench, so you won’t damage the trip wire, and remove both nuts that secure the coin return chute onto the inner panel. Now hold the return chute subassembly together in one hand, and replace the defective switch. The trip wire can be replaced by caretully prying up the black intemal-tooth retainer with a small flat screwdriver. Then remove the wire from the brasscolored stud. Be sure to replace the wire with another of the proper color (four are available, depending on coin denomination). li the new wire is loose when placed on the stud, squeeze the stud’s two halves together with a pair of pliers to secure the wire. Then replace the retainer. Make certain that the wire projects thru the entire width of the coin slot: otherwise no credits will be granted, even for genuine coins. The wire's normal rest position is against the top of the curved slot.

TRIP WIRE

SWITCH RETAINER

Figure 13 Switch and Trip Wire Replacement

Page 25

COIN INLET CHUTE

LAMP BRACKET

Remove the screw that secures the lamp and its “Z” bracket to the coin inlet chute. Replace the burned-out bulb. Then mount the lamp holder bracket back on the coin inlet chute.

Figure 14 Coin Door Lamp Replacement

H. Game Operation

With this manual you received two large sheets that contain the wiring and schematic diagrams for your game. Sheet 1, Side A, includes information that shows the arrangement of these diagrams. These diagrams include information that explains the functions of the circuits and defines inputs and outputs.

Atari Asteroids™ is a microprocessor-controlled game. The microprocessor is contained on the game PCB. The game PCB receives switch inputs from the control panel and coin door. These inputs are processed by the game PCB and output to the TV monitor, Regulator/Audio PCB, and control panel.

The TV monitor is an X-Y monitor. Therefore, the monitor receives signals for the X, Y and Z axes. Since the location of the beam in the monitor is totally controlled by the X- and Y-axis outputs of the game PCB, the game PCB does not contain a standard sync circuit. The X- and Y-axis inputs to the monitor step in increments of 1024 steps for the X (horizontal) axis, and 768 steps for the Y (vertical) axis. The Z axis merely controls the intensity of the beam.

The Regulator/Audio PCB performs two functions: 1) it regulates the + 10.3 VDC from the power supply to +5 VDC, and 2) it amplifies the audio output from the game PCB. The +5 VOC from the Regulator/Audio PCB provides most logic power to the game PCB. The audio output from the Regulator/Audio PCB directly drives the game speaker and is controlled by the volume control, mounted inside the coin door.

The Power Supply is the source of all voltages in the game. These voltages are protected by five fuses in the fuse block on the power supply chassis. The primary winding of the power supply transformer is protected by the cartridge-type fuse in the power supply chassis.

Figure 15 illustrates the distribution of power in this game. Figure 16 il\ustrates the distribution of signals.

Page 26

TV MONITOR

FLUORESCENT LAMP.

s) POWER INTERLOCK ER INTERL \Ler REGULATORIAUDIO PCB

| GAME PCB “SS Ss

LINE VOLTAGE

+5 VDC q 5 N gi gS =| 3] 2 ol | g i ma ss a SS al g| 3 3] 8 3 BY ( Quine VOLTAGE q POWER SUPPLY oe A

IN Ss AC POWER CORD

N POWER ONIOFF SWITCH

Figure 15 Power Distribution

Page 27

CONTROL PANEL

VOLUME CONTROL

FIRE

COIN DOOR

SELF-TEST SWITCH

THRUST

HYPERSPACE

ROTATE RIGHT ‘START2 LED

‘START2 W TV MONITOR

‘START1LED

Figure 16 Signal Distribution

AUDION&2

GAME SPEAKER

REGULATOR/AUDIO PCB

XouT. Your Zour

Page 28

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 29

Illus

trated Parts Lists

The purpose of this chapter is to provide you with ihe necessary information for ordering replacement parts for your Asteroids™ game. Please note that, for simplicity, common hardware has been deleted from most of these parts lists. This includes screws, nuts, washers, bolts, etc.

The parts lists have been arranged in alphanumeric order. For example, all “A-” prefix numbers come first. Following this are numbers in sequence evaluated up to the hyphen, namely 00-thru 99-, then 000598- thru approximately 110000-.

When ordering parts from your distibutor, give the part number, part name, applicable figure number of this manual, and serial number of your game. This will help to avoid confusion and mistakes in your order. We hope the results will be less downtime and more profit from your game.

Page 30

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING. CONFIDENTIAL: Reproduction forbiaden without tne specific wiltlen permission of Atari, Inc,, Sunnyvale, A. This drawing is only conditionally issued, and neitmer receipt for possession thereof confers o: vansiers any right in, or license to use, the subject matier of the drawing or any design or technical infor: mation shown thereon, nor any right to reproduce this Grawing of any part thereo!. Except for manufacture by vendors at Alarl, Inc., and for msnulacture under 036221.01 the corporation's wien ‘license, no right fo reproduce this drawing Is qranied or ihe subject mat- (Trim Cap) 92.045 ter Inet urices By wien agreement wih or writ 036220.91 03622801 (Monitor) ten permission from the corporation 03622401 5 (Shield Support) (Mon, Shield)

036225-01 it 0027 28-0 ‘Grile) (Ctrl. Panel Brkt.) Control Panel Assy.— See Figure 18 48-004 (Speaker) 036219-01 Fluorescent Light— See Figure 19 (Attract. Panel) ig oas7 "70304 (Fluor. Tube) (PCB Retainer)

‘A036210-01 (Access Panel)

035745-02 (PCB Retainer) l A036189.01 (Switch)

006870-01 {Coin Box Brkt)

A021700-01, -02, -03 a“ $2114 (Coin Box) (Lock)

007882-02 Reg/Audio PCB Assy.- {Switch Cover) See Figure 20 Geparator)

A036189-01 (aen Game PCB Assy.— See Figure 21 New Coin Door— See Figure 23 034536-03 Power Supply Assy. (Foam) See Figure 21

009992-01 (Switch Cover)

A034631-01 (On/Off Switch)

A034841-02 OR A034863-02 (Power Cord)

Figure 17 Cabinet-Mounted Assemblies A036218-xx A

Page 31

Figure 17 Cabinet-Mounted Assemblies Parts List

Part No. Description

A021700-01Coin Box Assembly(for all the same coins)
A021700-02Coin Box Assembly(for two different coin denominations—has one separator)
A021700-03Coin Box Assembly(for three different coin denominations—has two separators)

A030169-02 Volume Control/Bracket Assembly A034631-01 On/Off Switch Assembly

A034841-02Strain Relief Power Cord(domestic)

OR

A034863-02Strain Relief Power Cord(German)

A036189-01 Interlock Switch & Bracket Assembly (modified for safety) A036210-01 Access Panel Assembly DP-155-01 Asteroids™/Cabaret Schematic Drawings, Sheet 1 DP-155-02 Asteroids/Cabaret Schematic Drawings, Sheet 2 TM-151 Instruction and Service Manual for QuadraScan™ Model GO5-805 Monochrome X-Y Monitor TM-155 Asteroids/Cabaret™ Operation, Maintenance, Service Manual 48-004 5" 8-Ohm 5-Watt High-Fidelity Speaker 70-304 18” 15-Watt Cool White Fluorescent Lamp 71-2114 Panel Cartridge Lock Mechanism (for access panel)

78-240125" Beaded Nylon Tie Wrap(for securing edge connector to Game PCB)

92-045 15” QuadraScan™ X-Y Monitor 002728-01 Control-Panel Mounting Bracket 006870-01 Coin Box Bracket 00788202 Interlock Switch Cover 009992-01 On/Off Switch Cover 030249-01 Coin Box Separator 034536-03 Foam Vibration Damper 035723-01 Product Identification Label 035745-02 18”-Long Plastic PCB Retainer 035745-03 10”-Long Plastic PCB Retainer 036219-01 Attraction Panel with Graphics 036220-01 Monitor Shield (smoke color) 036221-01 Rounded Trim Cap 036224-01 Support for Monitor Shield 036225-01 Speaker Grille 036228-01 Cardboard Bezel (for monitor)

Page 32

A036046-01

036223-01

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without ihe specitic written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally’ issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, hor any sight to reproduce th's drawing or any part thereof. Except for manufacture by vendors of Atari Inc., and for manufacture under the corporation’s writien license, no right to reproduce this drawing Is granted or the subject matter thereof unless by written agreement with or written permission from the corporation. 75-07054 033127-01 / 62.039 —t

75-9910W0

cs of 75-9910NO 160004-001 a —* os ~ SES 160001-001

Figure 18 Control Panel Assembly A036226-01 A Parts List

Part No. Description

A036046-01 Button Assembly A036254-01 Control Panel Harness Assembly 62-039 SPDT Momentary Pushbutton Switch, with Red Cap and Light-Emitting Diode 75-07054 Flat Nylon Washer, 0.470” inside diameter x 0.968” outside diameter x 0.075” thick 75-9910NO 5/8-11 Steel Stamped Nut 75-9910W0 15/32-32 Steel Stamped Nut 033127-01 Black Molded Switch Bushing 036223-01 Control Panel with Graphics 160001-001 Leaf Switch with Button Holder 160004 -001 Leaf Switch Only

Page 33

70-304 (Not part of this assembly, but listed here for your convenience)

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the Specific written permission of Atati, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereot confers or transters any right in, 9° license ‘0 use, the subject matter af the drawing or any design or technical infor: Maton shown thereon, nor any right fo reproduce this drawing or any part thereo!. Except for manufacture by vendors of Alat, inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the sublect matter thereot unless by written agreement with or writ ten permission from the corporation,

Figure 19 Fluorescent Light Assembly A036205-01

Parts List A 035835-01

79-561816P

Part No. Description

A005493-01 Fluorescent Light Harness Assembly 70-304 18” 15-Watt Cool White Fluorescent Lamp (not part of this assembly, but listed here for your convenience) 79-561816P Wire Nut for 16- to 18-Guage Wires 99-11003 Fluorescent Lamp Starter 99-11008 Ballast Transformer 99-11009 Starter Socket 99-11011 1¥2" Clamp 035835-01 Y-Lead Connector

Page 34

we jeer

NOTICE TO ALL PERSONS

rd { { —————* Y © Oe 2s awa0ss, Oo

©

ING THIS DRAWING

D A034485-01 Figure 20 Regulator/Audio PCB Assembly

Page 35

Figure 20 Regulator/Audio PCB Assembly Parts List

ItemPart No.Description (Reference Designations in Bold)
2110000-0101 Ohm, + 5%, YW Resistor(R10, 19)
3110000-10010 Ohm, + 5%, %W Resistor(R11, 20)
4110000-33033 Ohm, + 5%, %4W Resistor(R3)
5110000-101100 Ohm, + 5%, %4W Resistor(R4, 12, 17, 18, 22)
6110000-271270 Ohm, + 5%, %4W Resistor(R1)
7110000-1021K Ohm, + 5%, %W Resistor(R2)
8110000-2722.7K Ohm, + 5%, YW Resistor(R23)
i)110000-7527.5K Ohm, + 5%, Y4W Resistor(R7)
10110000-10310K Ohm, + 5%, YW Resistor(R13, 14)
W110000-3923.9K Ohm, + 5%, %W Resistor(R6)
13110001-221220 Ohm, + 5%, %W Resistor(R9, 21)
1512-52P72.7 Ohm, + 5%, 1W Resistor(R5)
1619-100P10151 Ohm, + 3%, 7W Wirewound Resistor(R24)
1719-3151021K Ohm Vertical PCB-Mounting Cermet Trimpot, Bournes Series 3352V-1-1K(R8)
2024-25010610 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C6, 15)
2224-250477470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C1, 4, 12)
2324-250108.100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C9, 10, 13)
2527-250103.01 uf Ceramic-Disc 25V Radial-Lead Capacitor(C5, C14)
2627-250104.1 uf Ceramic-Disc 25V Radial-Lead Capacitor (C3, C11)
2727-250224.22 uf Ceramic-Disc 25V Radial-Lead Capacitor (C8, 17)
2927-250102.001 uf Ceramic-Disc 25V Radial-Lead Capacitor(C2, 7, 16)
3131-A14F50V 2.5A Miniature Axial-Lead High-Current Rectifier (CR1, CR4)
3231-1N400750V Silicon Rectifier 1N4001 Diode (CR2-3)
3433-TIP32PNP Power Transistor, Type TIP32 (Q2)
35,34-2N3055,NPN Silicon Transistor, Type 2N3055Q3)
3634-2N3904NPN Silicon Transistor, Type 2N3904(Q4, 6)
3837-LM3055V Linear Voltage Regulator (Q1)
39137151-002Type TDA2002A 8W Linear Audio Amplifier Integrated Circuit(Q5, 7)
4479-580089-Position Connector Receptacle(J7)
4579-580926-Position Connector Receptacle(J6)
4679-580594-Position Connector Receptacle(J8)
4779-20230Female PCB-Mounting Terminal
48034531-01Heat Sink
4972-1608C#6-32 x 2” Cross-Recessed Pan-Head Corrosion-Resistant Steel Machine Screw
5075-99516#6-32 Nut/Washer Assembly
5175-056#6 Internal-Tooth Steel Lock Washer
52020670-01Test Point
5375-F60805#6-32 x ¥2" Binder-Head Nylon Screw
5778-16008Thermally Conductive Compound for the 2N3055
5878-16014Thermally Conductive Compound for TDA2002A and TIP32
6052-003Teflon-Insulated Solder-Plated Solid Copper PCB-Mounting Jumper Wire with

.6" Centers

6152-004Teflon-Insulated Solder-Plated Solid Copper PCB-Mounting Jumper Wire with .3”

Centers

Page 36

IgG 723, 2auseas at a2 “Sgauon ers AM 635498 AT PZ 784 veesow

chow) Seiad TTT TH eee ee a

Ear

BS = 2° = fs Ss 82 = 53 = = «= 22 = 3) = g

Be ° ¥o. i gaat ct E8s

mee Ta] a 286 et gaz ; = Est = ges

tt 2d we = io 23 -

: pes Eyes oa BSS Pas! oget DOS asa USE RES NETWoRES, 2018 RP2, ITEM 34, ONLY Th INSTACUING TEiSIIo POS Fane oy

G Figure 21 Asteroids Game PCB Assembly A034986-03 and -04

Page 37

Figure 21 Asteroids Game PCB Assembly Parts List

ItemPart No.Description(Reference Designations and Locations in Bold)
2100000-27027 Ohm, +5%, YW Resistor(R72)
3100000-68068 Ohm, +5%, %4W Resistor (R71)
4100000-121120 Ohm, +5%, YaW Resistor (R105, 109)
5100000-151150 Ohm, +5%, %4W Resistor (R55)
6100000-331330 Ohm, +5%, %4W Resistor (R30, 31, 115)
7100000-471470 Ohm, +5%, %4W Resistor (R32, 87-99)
8100000-681680 Ohm, +5%, %W Resistor (R57, 61)
9100000-1021K Ohm, +5%, %4W Resistor (R27, 29, 53, 73, 85, 86, 132, 134)
10100000-271270 Ohm, +5%, %4W Resistor (R112, 113)
onl100000-1221.2K Ohm, +5%, %4W Resistor (R35, 100)
12100000-2222.2K Ohm, +5%, V4W Resistor (R36, 75, 117, 123, 133, 141)
13100000-2722.7K Ohm, +5%, YW Resistor (R66)
14100000-3323.3K Ohm, +5%, “%W Resistor (R56, 65, 74, 142)
15100000-3923.9K Ohm, +5%, %4W Resistor (R39, 64, 106-108)
16100000-4724.7K Ohm, +5%, YW Resistor (R37, 82, 102, 137, 140, 144)
17100000-5625.6K Ohm, +5%, YW Resistor(R40, 62, 67)
18100000-6826.8K Ohm, +5%, %4W Resistor(R49, 104, 128, 129)
20100000-10310K Ohm, +5%, ‘4W Resistor (R9-26, 28, 33, 38, 54, 58-60, 63, 69, 70, 79,

80, 103, 110, 111, 116, 122, 130, 131, 135, 136, 138, 139)

at100000-12312K Ohm, +5%, %4W Resistor (R43)
22100000-153,15K Ohm, +5%, %4W Resistor (R68)
23100000-18318K Ohm, +5%, YW Resistor (R51, 146)
24100000-22322K Ohm, +5%, YW Resistor (R1-8, 34, 41, 45, 50)
25100000-33333K Ohm, +5%, Y4W Resistor (R52)
26100000-47347K Ohm, +5%, %4W Resistor (R42, 44, 48, 76, 78, 83, 114)
27100000-563,56K Ohm, +5%, %4W Resistor (R145)
28100000-104100K Ohm, +5%, %4W Resistor (R46, 81, 84, 143)
29100000-224220K Ohm, +5%, YaW Resistor(R47)
30100000-274270K Ohm, +5%, ‘4W Resistor (R101)
33100000-393,39K Ohm, +5%, %4W Resistor (R77)
3419-00710K Ohm, 8-Pin Resistor Network. Use with the LS170 only, item 120. (RP1, 2)
3519-31510310K Ohm Vertical PCB-Mounting Cermet Trimpot, Bournes Series

3352V-1-10K (R120, 126)

3921-101104-1uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor(C84, 67-69)
4021-101224.22 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C33)
421-101473.047 uf, + 10%, Radial-Lead Epoxy-Dipped 100V Mylar Capacitor (C46)
4424-2501051.0 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor (C25, 70, 90, 92,

93)

4524-250107100 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C19)
4624-250477470 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C86, 87)
4724-25022622 uf Aluminum Electrolytic Fixed Axial-Lead 25V Capacitor(C117)
4927-250102.001 uf Ceramic-Disc 25V Radial-Lead Capacitor (C56)
5027-250103.01 uf Ceramic-Disc 25V Radial-Lead Capacitor(C27, 32, 36, 40, 55, 58)
5129-088-1 uf Ceramic-Disc 25V Radial-Lead Capacitor(C1-18, 20-23, 26, 28-31, 34, 37,

41-44, 49, 51-54, 57, 60, 61, 63, 65, 66, 71-85, 91, 94-96, 99, 100, 103, 104, 107, 108, 144, 112, 114-116, 120-123)

5328-10110010 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C97, 105)
5428-10168068 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C102, 110)
55.28-101101100 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C89)
5628-101221220 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor (C98, 106, 118, 119)
5728-101271270 pf Radiai-Lead Epoxy-Dipped 100V Mica Capacitor(C59)
5828-101391390 pf Radial-Lead Epoxy-Dipped 100V Mica Capacitor(C88)
6129-0061.0 uf,+10%, 35V Tantalum Capacitor (C24, 35, 47, 50, 62, 113)
6329-046,10 uf, 10%, 20V Tantalum Capacitor(C38, 39, 45, 48)
6531-1N100100V Type-1N100 Switching Diode(CR16)
6631-1N91475V Type-1N914 Switching Diode(CR1-4, 6-8, 15)
6731-1N400150V Type-1N4001 Silicon Rectifier Diode(CR9-12)
Page 38

Figure 21 Asteroids Game PCB Assembly, continued Parts List

ItemPart No.Description(Reference Designations and Locations in Bold)
6831-1N756A8.2V, +5%, 1N756A Zener Diode(CR13, 14)
7133-2N3906Type-2N3906 PNP Switching and Amplifying Transistor (Q1-5, 7, 10, 16, 17)
7234-2N3643Type-2N3643 NPN Silicon Transistor (Q6)
7334-2N3904,Type-2N3904 NPN 60V 1-Watt Transistor (Q8, 9)
7434-2N6044Type-2N6044 Darlington NPN Transistor(Q11-13)
re)34-MPSA06SType-MPSA06S NPN 80V 500ma Transistor (Q14, 15)
7837-74LS00Type 74LSO00 Integrated Circuit(N5, C6)
7937-74LS02Type 74LS02 Integrated Circuit(D6)
8037-7404Type 7404 Integrated Circuit(H10)
8137-74LS04Type 74LS04 Integrated Circuit(B5, 15)
8237-7406Type 7406 Integrated Circuit(N9)
8337-74LS08Type 74LS08 Integrated Circuit(E6, K6, R7, B8)
8437-74LS10Type 74LS10 Integrated Circuit(A8)
8537-74LS14Type 74LS14 Integrated Circuit(B6)
8637-74LS20Type 74L820 Integrated Circuit(E5)
8737-74LS32Type 74LS32 Integrated Circuit(M5, N6, BS)
8837-74LS42Type 74LS42 Integrated Circuit(L6, E7, E8)
8937-74LS74Type 74LS74 Integrated Circuit(D4, A7, R&)
137-74LS83Type 74LS83 Integrated Circuit (M6)
9237-74LS86Type 74LS886 Integrated Circuit(P5)
9337-7497Type 7497 Integrated Circuit(F8, H8, J8, K8)
9437-74LS109Type 74LS109 Integrated Circuit(A9)
9537-74LS139Type 74LS139 Integrated Circuit (L3, £4)
9737-74LS157Type 74LS157 Integrated Circuit(F3, H3, J3, K3, F6, A10, B/C10, C10, D/E10, £10,

FIH10)

9837-74LS161Type 74LS161 Integrated Circuit(D7)
9937-74LS164Type 74LS164 Integrated Circuit(K9, P9, R9)
10137-74LS174Type 74LS174 Integrated Circuit(N7, P7, D8, N11, F10)
10237-74LS175Type 74LS175 Integrated Circuit(M7)
10437-74LS191Type 74LS191 Integrated Circuit(K5, C9, 09, E9, F9, H9, J9)
10537-74LS193Type 74LS193 Integrated Circuit(F5, HS, J5)
10637-74LS244Type 74LS244 Integrated Circuit(B2, C2)
10737-74LS245Type 74LS245 Integrated Circuit(R2, £3)

' OR

10837-8304BType 83048 Integrated Circuit—substitute for item 107 (P2, £3)
11037-74LS251Type 74LS251 Integrated Circuit(J10, L10)
11437-74LS253Type 74LS253 Integrated Circuit (P6)
11237-74LS259Type 74LS259 Integrated Circuit(M10)
11337-74LS273Type 74LS273 Integrated Circuit(F7, H7, J7, K7)
11437-74LS367Type 74LS367 Integrated Circuit(H6, J6)
11637-74LS393Type 74LS393 Integrated Circuit(B4, DS)
737-74LS374Type 74LS374 Integrated Circuit(B10, D10)

OR

11837-74LS273Type 74LS273 Integrated Circuit—substitute for item 117 (B10, D10)
11937-74LS670Type 74LS670 Integrated Circuit (F4, H4, J4)

OR

12037-74LS170Type 74LS170 Integrated Circuit—substitute for item 119(F4, H4, J4)
12137-9316Type 9316 Integrated Circuit(C4, C5, P8, B7, C7)
12237-LM324Type LM324 Integrated Circuit(L8, P11)
12437-555Type 555 Timer Integrated Circuit(M8, N8, L9, R10)
12537-566Type 566 Function Generator Integrated Circuit(P10)
12737-4016BType 4016B Integrated Circuit(M9, N10, R11, B12, D12)
12837-TLO82CPType TLO82CP integrated Circuit(A12, C12)
12937-AD561dType AD561¥ Integrated Circuit (B11, D11)
130137108-001Type TLO81CP Operational Amplifier Integrated Circuit(B/C12, E12)
13237-7805+5V Voltage Regulator (VR3)
Page 39

Figure 21 Asteroids Game PCB Assembly, continued Parts List

ItemPart No.Description (Reference Designations and Locations in Bold)
13337-7812+12V Voltage Regulator (VR1)
13437-7815+15V Voltage Regulator (VR4)
13537-7915— 15V Voltage Regulator (VR2)
13738-MV5053Type MV5053 Light-Emitting Diode (CR5)
13941-3003100 uH, +5%, Hot-Molded Plastic Fixed R.F. Choke (L1-15)
14162-001SPST Pushbutton Switch (A6)
14266-118P1T8-Station Single-Throw, Dual-Inline-Package Bit Switch (R6)
14366-114P1T4-Station Single-Throw, Dual-Inline-Package Bit Switch (M12)
14479-42C4040-Contact Medium-Insertion-Force Integrated Circuit Socket (C3)
14681-4302Nylon Snap-In Fastener
148020670-01Test Point
15090-10212.096 MHz, +.005%, Crystal (¥1)
15190-6013Microprocessor (C3)
15290-7033Random-Access Memory (D2, E2, M4, N4, P4, R4)
155034602-01Programmable Read-Only Memory (C8)
157035127-01Read-Only Memory _ (N/P3)

OR THE FOLLOWING TWO ITEMS:

159035129-01Programmable Read-Only Memory, MSB—substitute for half of item 157 (K4)
159035130-01Programmable Read-Only Memory, LSB—substitute for half of item 157 (L4)
18779-42C01818-Contact Medium-Insertion-Force Integrated Circuit Socket (F2, H1, H2, J1,

J2, K1, K4, L1, L2, L4, M1, M2, N1, N2—used only on A034986-03 PCB assembly)

18879-42C2424-Contact Medium-Insertion-Force Integrated Circuit Socket (C1, D/E1, F1, N/P3)

For remaining memory components and their part numbers, see listing below.

Memory Components and Their Equivalents (Locations Shown in Bold)

-01 P.C. Boards Alternate -01 P.C. Boards -02 P.C. Boards (PROMs) (PROMs) (ROMs)

03513102 J2 035150-02 J2 03513202 N2 03514302 C1 035137-02 K1 035153-02 K1 035138-02 N1

035133-02 H2 03515102 H2 03513402 M2 03514402 DIE1 035139-02 J1 03515402 J1 035140-02 M1

03513502 F2 03515202 F2 035136-02 L2 03514502 F1 035141-02 H1 035155-02 H1 035142-02 L1

Page 40

RB 034482-01 79-4411006 46-2017002 034544-01 46-2013002

TOP VIEW 78-2708

NOTICE TO ALL PERSONS RECEIVING THIS ORAWING CONFIDENTIAL: Reproduction forbidden without the Speers wiiten permission of Alar, Ine. Sunnyvals GA This drawing Is only conditionally Issued, and nether reseipt nor possession thereat confers. oF TTansforg ny ight itor icenoe {0 tse. the "uoject imaiter of ine drawing er any design or technical lor. allonshown irereon, ror any tht to reproduce his Grawing or any putt thereat. Except for manutactuse By vendors of alae, Ine, and for manutacture under tRe “corporation's. writen’ Veenge, no. rght to (ebteduce Me drawing s arte a ne Subject mat {er thenoo! unless by writen agreement wit oF wrt 442000-001 ‘Gn pormssion from the corporation

BOTTOM VIEW

A034629-01

Figure 22 Power Supply Assembly for X-Y Games A034561-03 E

Page 41

Figure 22 Power Supply Assembly for X-Y Games Parts List

Part No. Description

A006555-01 Rectifier Printed Circuit Board Assembly A034623-03 Power Supply Harness Assembly, includes Shielded Power Transformer A034629-01 A.C, Harness Assembly A034630-01 RFI Filter Assembly A035674-01 Voltage Plug Assembly (set of four plugs) 29-053 26,000 uf 15 V Electrolytic Capacitor 46-2013002 3-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse 46-2017002 7-Amp. 250 V 3AG Slow-Blow Glass Cartridge-Type Fuse

78-2708 Nylon Type 6/6 Hole Bushing with 5/8” Inside Diameter x 55/64” Outside Diameter x 14" Thick 78-70501SC 2" Diameter Capacitor Mounting Bracket 79-15021001 2-Circuit Single-Row Terminal Block 79-3206 5-Position 3AG Fuse Block with 4” Quick-Disconnect Terminals 79-4411006 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post 034482-01 Power Supply Chassis 034544-01 Fuse Block Cover 142000-001 Shielded Power Transformer

Page 42

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific writ 40103 ten permission of Atari, Inc., Sunnyvale, CA. This drawing is only 98) ‘conditionally issued, and neither receipt nor possession thereot confers or transfers any right in, or license to use, the subject mat- 75-948S, ter of the drawing or any design or technical information shown 940096 thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari Inc., and for manutacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by wrtten agreement with or written permission from the corporation. 99-10071 99-10095

99-10073

PART OF 99-10095,

99-10064

COIN INLET CHUTE S 99-10097 99-10101

70-11-47

99-10080

99-10105

COIN MECHANISM SEE PARTS LIST (71-1210)

99-10102 COIN RETURN{ 99-0065 SWITCH WIRE CHUTE 99-10068 J SEE PARTS LIST ae (99-10075 thru Stina COIN switcn aséy, | 9°7°78) PART OF '¢9-10047 99-1008 SEE PARTS LIST 99-1082 (99-1022 thru 7514128 99-10045)

Figure 23 New Coin Door 71 -10xxxx

Page 43

REJECT BUTTON COVER SEE PARTS LIST (99-10055 thru $9-10059) PRICE PLATE SEE PARTS LIST

COIN RETURN BUTTON ASSY —@)

SEE PARTS LIST (99-10070, 99-10083 99-10074 (9-10012 thru 9910022) thru $8-10082) 9910062 72-JA1405B COIN DOOR ONLY SEE PARTS LIST 99-10054 (99-10009 thru 99-10010) 72-HA1404C

PART OF 99-1074 [}

75-5520B

NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transters any right in, or license to use,

the subject matter of the drawing of any design of

technical information shown thereon, nor any right to reproduce this drawing or any part thereo| Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's writ: ten license, no right to reproduce this drawing is granted or the subject matter thereo! unless by written agreement with or written permission from the corporation. 99-10066

72-JA1405B

99-10051

Figure 23 New Coin Door 71-10xXxxx

Page 44

oo Figure 23 New Coin Door, continued Parts List

Part No. Description

31-1N4002 100V Silicon Rectifier 1N4002 Diode 65-441C General-usage low-force miniature switch 70-11-47 Miniature bayonet-base incandescent lamp, type #47 71-1201ADU U.S. $1.00 coin mechanism 71-1201FCH Swiss 1 Fr coin mechanism 71-1201MG German 1 DM coin mechanism 71-1202MG German 2 DM coin mechanism 71-1205FB Belgian 5 Fr coin mechanism 71-1205MG German 5 DM coin mechanism 74-1210PE U.K. 10 P coin mechanism 71-1220CA Australian 20¢ coin mechanism 71-1225CU U.S. 25¢ coin mechanism 71-12100LI Italian 100 Lire coin mechanism 71-12100YJ Japanese Y100 coin mechanism 72-HA1404C #4x%4” Slotted pan-head thread-rolling tri-fluted “Taptite" cadmium-plated screw 72-JA1405B, #4x5/16" Slotted pan-head thread-rolling tri-fluted “‘Plastite” black screw 72-9406S #4-40x3/8” Slotted truss-head steel machine screw 72-9603S #6-32x3/16" Slotied truss-head steel machine screw 75-915S #14-20 Standard pattern cadmium-plated steel hex nut 75-918S #8-32 Standard pattern cadmium-plated steel hex nut 75-9448, #4-40 Polymer self-locking steel hex nut 75-948S #8-32 Polymer self-locking Steel hex nut 75-1408S #4-40x /2” Slotted pan-head steel machine screw 75-1412S, #4-40x 34" Slotted pan-head steel machine screw 75-5520B #%-20x114”" Round-head square-neck steel bolt with black finish 99-10008 Switch wire retainer 99-10009 2-Mech coin door only 99-10010 3-Mech coin door only 99-10011 Inner panel 99-10012 U.S. 25¢ coin return button assembly 99-10013 U.S. $1.00 coin return button assembly 99-10014 German 1 DM coin return button assembly 99-10015 German 2 DM coin return button assembly 99-10016 German 5 DM coin return button assembly 99-10017 Belgian 5 Fr coin return button assembly 99-10018 Swiss 1 Fr coin return button assembly 99-10019 Japanese Y100 coin return button assembly 99-10020 U.K. 10 P coin return button assembly 99-10021 Australian 20¢ coin return button assembly 99-10022 Italian 100 Lire coin return button assembly 99-10040 Coin inlet chute assembly 99-10041 Coin counter assembly 99-10042 Coin switch assembly for U.S. 25¢ and Belgian 5 Fr coins (silver wire) 99-10043 Coin switch assembly for German 1 DM, Swiss 1 Fr, and Japanese Y100 coins (black wire) 99-10044 Coin switch assembly for U.S. $1.00, German 2 DM, and Italian 100.Lire coins (gold wire)

Page 45

Asteroids™/ Cabaret

Figure 23 New Coin Door, continued Parts List

Part No. Description

99-10045 Coin switch assembly for German 5 DM, U.K. 10 P, and Australian 20¢ coins (green wire) 99-10047 Lockout coil assembly 99-10048 Coin door harness assembly 99-10049 Locking arm assembly 99-10051 Coin door frame 99-10054 Coin button housing 99-10055 Coin return button cover for Japanese Y100 coin 99-10056 Coin return button cover for German 1 DM and Swiss 1 Fr coins 99-10057 Coin return button cover for U.S. 25¢ and Belgian 5 Fr coins 99-10058 Coin return button cover for U.S. $1.00, German 2 DM, and Italian 100 Lire coins 99-10059 Coin return button cover for German 5 DM, U.K. 10 P, and Australian 20¢ coins 99-10061 Coin return bezel 99-10062 Coin return button 99-10063 Right half of coin inlet chute 99-10064 Left half of coin inlet chute 99-10065 Coin return box 99-10066 Coin return cover 99-10070 U.S. 25¢ price plate 99-10071 Slam switch assembly 99-10073 Test switch decal 99-10074 Lock assembly 99-10075, Black switch wire—for German 1DM, Swiss 1Fr and Japanese Y100 coins 99-10076 Silver switch wire—for U.S. 25¢ and Belgian 5Fr coins 99-10077 Gold switch wire—for U.S. $1.00, German 2DM and Italian 100 Lire coins 99-10078 Green switch wire—for German 5DM, U.K. 10P and Australian 20¢ coins 99-10080 Miniature bayonet-base lamp socket 99-10081 Wire key holder 99-10082 Switch cover 99-10083 US. $1.00 price plate 99-10084 German 1 DM price plate 99-10085 German 2 DM price plate 99-10086 German 5 DM price plate 99-10087 Belgian 5 Fr price plate 99-10088 Swiss 1 Fr price plate 99-10089 Japanese Y100 price plate 99-10090 U.K. 10 P price plate 99-10091 Australian 20¢ price-plate 99-10092 Italian 100 Lire price piate 99-10094 Fish paper insulation 99-10095, Toggle switch 99-10096 “U”-type fastener 99-10097 Fish paper insulation 99-10101 Coin inlet chute sub-assembly 99-10102 Switch and lockout coil bracket sub-assembly 99-10103 Inner panel with levers sub-assembly 99-10104 Anti-penny-flip bar retainer 99-10105. Anti-penny-flip bar

Page 46

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 47

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 48

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.

Page 49

oe YOUR COMMENTS, PLEASE!

Your comments will assist Atari in improving the usefulness of our publications. They are an important part of preparing for revisions of manuals and parts catalogs. No postage stamp is necessary if mailed in the U.S.A.

If you have any technical questions about certain Atari or Kee Games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.

Page: Comments:

Fill in if you wish a reply:

Name Firm 0 Distributor O Operator Address OC) Other

City = State Zip

TM-155 ‘1st printing

Page 50

First fold.

SI

SS REPLY MAIL

FIRST CLASS PERMIT NO. 1004 SUNNYVALE, CA

POSTAGE WILL BE PAID BY ADDRESSEE

Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086 No Postage Necessary if mailed in the United States

Second fold

Cut along this line

Page 51

Seller warrants that its printed circuit boards and parts thereon‘are free from defects:in material and workmanship under normal use -and service for a petiod of ninety (90) days from:date-of shipment. Seller. warrants that its ‘television monitors (in games supplied with monitors) are free. from defects:in- material and-workmanship under normal use and service for a period of thirty.

  • days from:date of shipment: None of the: Seller's othe products ‘OF Parts thereof are-war-~ ranted: =

If the: products-described’in this manual fail:to:conform to.this: warranty, Sellers~ sole-liability. shail-be,at its option, to repair, replace,.or credit Buyer's account-for such’ gestae whichare returned {6 Seller during said warranty period, provided: (ay Seller is promptly notified in writing upon discovery: by. ce thatsaid products are detective;

  • Such ‘products are-returned prepaid’ to Sellers’ plant:and (c): Selfer's-examination of said products discloses’ to Seller's “Salisfaction that such alleged defects exisied-and were notcaused by accident, misuse, neglect, alteration, mproner Epa installation Or, improper Lae INIA: event shall Seller be liable for:loss “of profits,loss: of use, incidenial or consequential damages: Except for any express warranty set forth in a written contract between Seller and Buyer which contract Supersedes the terms of this order, this warranty is. expressed.in lieu of all other-warranties expressed or implied, including the implied warranties of merchantabil:—— ity-and fitness-for a particular-purpose, and of all-other obligations or liabilities on ‘the. ‘Seller's part, and it neither assumes hor authorizes any other person to assume-for the Seller-any other liabilities in connection with the sale-of products under this order.

The-use of-any non-Atari parts‘ may. “wold your warranty, according to-the terms.of the warranty- The use of any non-Atari parts may. also: adversely-aftect the safely of your.game and calise in: jury. to-yourself-and others. Be-very-cautious: in using noh-Atari+ peupplled components with our games;-in order to insure your safety, Atari disributors are independent, being privately owned and Saas Inctheir judgment-they: may sell ‘paris oraccessories olherthan Atari paris:or accessories. Atari cannot be tesponsible for the-quality, suitability. or safety of any non-Atarl part or any modification including labor which is performed By Such distributor. This: document is and contains confidential trade. secret information of Atafi, Inc. This: document is-loaned-under contidential- custody for the-sole purpose- of operation, maintenance or repair.of Atari equipment and may not be used by or disclosed to-any. Reson for any other purpose whatever, and remains the. property os Atari,-Inc. Neitherit nor the information it-contains: maybe’ reproduced, used, or. disclosed to persons: nol having aneed to-know: consistent with the purpose of the loan, without written consent of Atati, Inc.

Page 52

This page carries no recoverable text. It is a drawing or a photograph. See the original scan.