CATHODE RAY TOMES

Airwolf

Airwolf (Kyugo, 1987) · Document · 8 pages · 14 sections · original scan

Page 1

Flight Instruction

MANUAL

jar 2 oea0n Age

© 1984 Universal City Studios, Inc. All Rights Reserved. *A trademark of and licensed by Universal City Studios, Inc.

© 1987 Kyugo Trading co., Itd. MCA© 1984 Universal City Studios, Inc. All Rights Reserved ALL AMERICAN RIGHTS HELO BY: A Trademark of and licensed by UNITED ARTISTS THEATRE AMUSEMENTS Universal City Studios, Inc. PALM SPRINGS, CALIFORNIA

ze:

23 UNITED AMUSEM

= 1975 RIVERSIDE DRIVE LOS ANGELES, CA 90039 1 800 722 8258

Page 2

KIT CONTENTS

1. AIR WOLF PC BOARD il aan

  • AIR WOLF MARQUEE SIGN os
  • AIR WOLF MONITOR PLEXI -
  • WIRE HARNESS t, ve 5S. CONTROL PANEL OVERLAY
  • CONTROL PANEL PLEXI
  • B-WAY JOYSTICK ae <a

8. & BUTTONS WITH SWITCH ASSEMBLIES Pes :

  • INSTRUCTION LABELS
  • INSTRUCTION MANUAL

IMPORTANT F.C.C. WARNING

WARNING

This equipment generates, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. As temporarily permitted by regulation it has not been tested for compliance pursuant to subpart J of part 15 of F.C.C. rules, which are designed to provide reasonable protection against such interference. Operation of this equipment in a residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever. measures may be necessary to correct the interference.

Page 3

PREPARING THE CABINET

STEPS:

  • Remove the old F.C. board
  • Remove the control panel
  • Remove the marquee sign 4, Remove front or side decals S. Remove the old wire. harness

Leave all the A.C. wiring to monitor, power supply, flourescent lamps, fuses, on/off switches, and transformer circuitry intact. Remove all remaining wiring from the cabinet.

Clean the cabinet thoroughly and repair any visible damage. Using a coat of paint on an older cabinet can restore a "like new" appearance. If needed, painting should be performed at this time.

A little extra time and effort spent now on enhancing a cabinet's appearance will definitely result in increased earning power later!

SUGGESTED CONTROL PANEL LAYOUT

Loop LOOP O

PILOT 8 WAY JOYSTICK

MACHINE GUN MISSILE MISSILE MACHINE GUN O

PILOT

HORIZONTAL MONITOR MOUNTING = +5, +12, — VOLTS REQUIRED

Page 4

TY MONITOR:

SPECIAL REQUIREMENTS

This game is designed to be used with a

horizontally CX] vertically cod

mounted R.G.B. monitor, with the PCR as a negative polarity video and sink signals.

connection mtal and tive. Your new game requires one sink wire called "composite sink". Tie the hor vertical wires together, this signal is n Most monitors have supply positions for bath negative and positive sink.

FOWER SUPPLY:

The power supply requirements are as follows:

+5 VDC at 7 amps CX] +12 VDC at 1 amps cxI

If the power supply in the game does not meet these requirements, it should be replaced prior to beginning the conversion procedures.

CONTROL PANEL:

The control panel on the game to be converted can be either metal or wood. When selecting a game to convert consider the placement of joystick, push buttons and the monitor position.

Route the wires labeled control 1 (for upright) to your control panel. Cut this down to the required length. Strip and solder the wires to the joystick, and push buttons according to the pin-out assignments.

Page 5

MONITOR WIRING:

Route the wires labelled "VIDEO" or "MONITOR" up to your monitor and cut the excess wire. Refer to the Pin-out assignment at the back of this manual for video outputs.

GRN BLU

+ Vv +H

GND

COMP SI RED wire GREEN wire BLUE wire BLACK wire WHITE wire

K [|

WELLS GARNER The color code is as follows:

orem VIDEO RED VIDEO GREEN VIDEO BLUE VIDEO GROUND NEGATIVE COMP. SINK

  • SINK GROUND

ELECTRO HOME

Page 6

POWER SUPPLY WIRING:

Attach the wire harness connector to the main logic FCB. ¥*¥% CAUTION: Sometimes the connector is not keyed and it is very easy to install it reversed on the logic board. Double check that it is wired and connected properly. The label with the game name should face the component side of the PCH.

Separate the bundle of wires labeled "POWER" and route them to your power supply. Strip about 1/2 " off the insulation and attach them to the power supply screws. The color code is:

RED wire # 18 + S VDC GREEN wire # 18 + 12 VDC BLACK wire 9 0000000 Tee GROUND

NOTE: You can use the -5 VDC to power the lights to the coin door or the lighted push buttons.

COIN SWITCHES:

Most games have two coin outputs. Coin 1 must go to the N.0. (normally open) terminal of the micraswitch, (same as with coin 2) and a ground wire will ga to the common terminal of the microswitch.

If you wish to use a coin meter for both coin mechanisms, connect only one coin output to both coin switches. This will save you the use of two coin meters.

COIN 1 aml I GND — |] NO com

Page 7

<CONNECTION OF HARNESS>

PARTS SIDE

GND

GND

SP OUT

+12V

1P SHOT-2

+5V

1P

2P

2P

1P DOWN

SHOT-—2

SELECT

SELECT

1P RIGHT

1P LEFT

BLUE

GREEN

SYNC COO ADA &F WHY

en 7 one o SOLDER SIDE

GND

GND

GND

SERVICE

+12V

COIN2

+5V

2P UP

1P UP

2P DOWN

CcOIN1

1P SHOT-1

RED

2P RIGHT

2P LEFT

2P SHOT~-1

& 6 AIR GROUND sD VY Pp vovsic. PUSH HTWwo 'O FIRING UTTONS- LOOP CATCH THE GREEN RED PARACHUTE,AND THE FLAG, Bow wee GET AN EXTRA

Page 8

DIP SW Not

SWITCH NO.

NQ OF 4

FIGHTERS 5

TABLE

UP RIGHT S T O P | NORMAL OFF

SOUND, cp NORMAL OFF CONTINUE NORMAL OFF

FREE PLAY) NORMAL OFF

TYPE

DIP SW No2

SWITCH NO.

1PLAY/1COIN

2PLAY/1COIN

3PLAY/1COIN

4PLAY/1COIN

6PLAY/1COIN

1PLAY/2COIN

2PLAY/3COIN

FREE PLAY

I IPLAY/1COIN

2PLAY/1ICOIN

3PLAY/1COIN

4PLAY/3COIN

1PLAY/2COIN

1PLAY/3COIN

1PLAY/4COIN

1PLAY/SCOIN