CATHODE RAY TOMES

Great Sluggers

Great Sluggers (Japan) (Namco, 1993) · Manual · 15 pages · 5 sections · original scan

Page 1

namcoa

GREAT SLUGGERS™

Operators Manual

Page 2

Operator’s Manual Great Sluggers™

CONTENTS

1.0 Specifications .....csceccsecssecssecssteesseessneesnsessneesnessneessueessneesse 1.1 Game Description ...... 1.1.1 Game Modes... 1.1.2 Game Controls... 1.2 Game Play... 2.0 Game Conversion Overrview. 3.0 Precautions .......ceeeseeeeee 3.1 Installation Precautions . 3.2 Handling Precautions . 4.0 Inspection.. 5.0 Installation 5.1 Electronics 5.1.1 Installing the NAMCO PC board . 5.1.2 Connecting wiring harness .. 5.1.3. Connecting Speakers 5.1.4 Installing the FCC Ferrite 5.2 Player Controls ......ccsssecssecsesesseeess 5.2.1 Modifying the control panel 5.2.2. Wiring the control panel .. 5.3 Graphics ....seseeseeseees 5.3.1 Marquee Panel 5.3.2 Monitor Bezel ... 5.3.3 Cabinet Side Decals . 6.0 Test Mode ...ceececececnes 6.1 Switch Test Screen.. 6.2 Coin Option Screen 6.3. Game Option Screen..

6.4 — Option Settings Table ........cccceccccsseseesseessssseeeseseesssrestonsessansvessasssessnanersnneeeeenies Figures Figure 5-1 Location of connectors and controls on Game PCB . Figure 5-2 Player Control Panel Figure 6-1 Test Menu Screen. Figure 6-2 Switch Test Screen Figure 6-3 Coin Option Screen Figure 6-4 Game Option Screen ..

Tables Table 5-1 JAMMA Connector . Table 6-1 Game Options ...... WCODOODONDDAANNA ERR ARWWWHWNNNH HE

Page 3

Great Sluggers™ Operator's Manual

Great Sluggers™

VIDEO GAME CONVERSION KIT

1.0 SPECIFICATIONS

GAME NAME GREAT SLUGGERS™ MONITOR ORIENTATION: Horizontal CONVERSION OPTIONS: 2-Player upright CONTROL PANEL TYPE: 2-player - 4 buttons per player CONTROLS SUPPLIED WITH KIT: 8-way Joystick 2 Start buttons 2 Game function buttons 6 EDGE CONNECTORS REQUIRED: JAMMA Standard (56-pin edge connector, 3.96 mm pitch) (48-pin edge connector, 2.54 mm pitch Optional for stereo sound) . POWER SUPPLY REQUIRED: +5 Volts DC @ 4.8 Amps +12 Volts DC @ 1.0 Amps

Note: Specifications may change without prior notice. Modification and/or alteration of the Great Sluggers™ game with kits or parts not supplied by NAMCO may void the warranty. Use only a JAMMA standard harness, as any modification, such as filing the edges of the Printed Circuit Board, may cause operational problems and also void the warti anty. Game Description Great Sluggers™ is a one or two-player interactive baseball game. The MLBPA logo on the game proudly displays NAMCO’s right to use all major league players belonging to the Major League Baseball Players Association. A new addition to baseball games is the use of current 1994 team rosters. These up-to-date rosters feature hot new rookies and big trades that aren't included in games with old rosters! Great Sluggers™ features an operator selectable “favorite team” from a list of 28 teams. This is generally the “hometown favorite” (no “favorite team” may also be selected). This feature slightly improves the performance of the selected team... something of a home field advantage! After at least one game has been played, list called “Form of Today’s Key Fielders” and “Form of Today’s Key Pitchers” will appear in Attract mode. This list shows what players are “hot” or “in the zone.” Smart players will keep their eyes on this data to get the edge on their opponent!
Page 4

Operator's Manual

1.2 Great Sluggers™

1.1.1. Game Modes

  • 1-Player Game - Play against the computer. Pay by the inning.
  • 2-Player Game - Play against the computer. Pay by the inning.
  • 1-Player Complete Game - 9-inning discount (max. of 15 innings) for paying before game start. + 2-Player Complete Game - Each receive a 9-inning discount (max. of 15 innings) for paying before game start.
  • Season Mode - All games begin in the 7th inning. Win the final three games of the season, win all the divisional playoffs and go all the way to the World Championship! .

1.1.2 Game Controls Each player has: + One Start button

  • One 8-Way Joystick
  • Three buttons for both at-bat and fielding situations Pitching/Fielding - The joystick and buttons are used to pitch, pickoff runners, move fielders, throw or run to any base, and relieve pitchers. Batting - The joystick and buttons are used to position the batter in the batters box, swing, steal, bunt, advance or return to any base, and call for a pinch hitter or pinch runner.

Game Play At game start, the player(s) make the following choices: te

  • Team selection
  • First at-bat
  • Starting pitcher
  • Batting order
  • “Fully-automatic” or “manual” fielding
  • “Traditional” or “Modern” stadium
  • Background music “BGM” or no background music “No BGM” Great Sluggers™ includes some game play secrets for players to learn to get the upper hand on the opponent. Be observant! Standard baseball rules apply. A game will be called if either player is winning by 20 runs. After completed games, the “NAMCO Sports News” reviews the game in summary and displays player statistics.
Page 5

Great Sluggers™ Operator’s Manual

2.0 GAME CONVERSION OVERVIEW

The Great Sluggers™ kit allows conversion of most 2-player upright video game cabinets to a NAMCO Great Sluggers™ game. Conversion consists of several steps, including: + Changing the Game PC Board

  • Modifying the control panel + Replacing the Marquee graphics panel + Replacing the Cabinet side graphics This manual provides step-by-step instructions for the conversion of existing games, and then describes the adjustments, tests, and troubleshooting associated with your new Great Sluggers™ game. Before starting the conversion, familiarize yourself with 5-1 Location of Controls and Connectors on the Game PCB, Figure 5-2 Player Control Panel, and Tables 5-1 JAMMA Connector Wiring and 5-2 Extended Connector Wiring.

3.0 PRECAUTIONS

3.1

3.2 Installation Precautions This game is designed for indoor use only. It should not be installed outdoors or under the following conditions:

  • In areas directly exposed to sunlight, high humidity, direct water contact, dust, high heat, or extreme cold.
  • In areas that would present an obstacle in case of emergency, i.e., near fire equipment or emergency exits.
  • On an unstable surface or subject to floor or other vibration.

Handling Precautions

  • AC Power should always be turned OFF, and the game unplugged, before replacing any parts.
  • When unplugging the game from an electrical outlet, always grasp the plug, not the line cord.
  • The cabinet should be grounded with a securely connected ground line.
  • The monitor includes areas of high voltage. Care should be taken at all times to avoid electrical shock whenever inspecting or adjusting the game.
  • DO NOT attempt to repair the Printed Circuit Board (PCB) on site. It contains sensitive integrated circuit chips that could easily be damaged by even the small internal voltage of a multi-meter. Always return the PCB to your distributor for any repairs.
  • Always return the levelers to the extreme “up” position before moving the game.
  • Adjustment is required whenever the game PCB is replaced.
Page 6

Operator's Manual Great Sluggers™

4.0 INSPECTION

The Great Sluggers™ Kit carton should be inspected carefully upon receipt to insure that the kit is complete and was delivered in good condition. The complete kit should contain the following:

  • NAMCO Game Printed Circuit Board
  • FCC Foil Shield
  • New game controls: a. 8-way joystick b. Start button (white P1) c. Start button (white P2) d. Button 1 - (Red) e. Button 2— (Blue) f. Button 3 - (White) g. Button ID Tags (A, B, & C) Monitor Bezel A NNNNNN

Monitor Bezel Instruction Panel Control Panel

Header Decal

Cabinet side graphics (left and right see)

4 PCB Mounting feet

  • Ferrite Clamps and Housing
  • FCC Label
  • This manual PON ANA

5.0 INSTALLATION

5.1 Electronics

Warning!

Be sure the power cord is disconnected before starting installation!

5.1.1 Installing the game PCB

  • Carefully disconnect the edge connector(s) from the existing game PCB.
  • Remove the existing game PCB from the cabinet.
  • Install the NAMCO Game PCB in the same location as the old PCB, using the mounting feet and hardware supplied with the kit.
  • Connect the JAMMA harness to the game PCB.
  • Install the FCC Foil Shield around the PCB.
Page 7

Great Sluggers™ Operator's Manual

56 Pin Edge Connector (AMMA): Speaker Volume 7 : ean Option Switch (2 places) No 1 ON—Test Mode No 2 ON—Screen Freeze (Normally Both OFF)

Figure 5-1 Location of Controls and Connectors on PCB

5.1.3 Connecting the speakers

  • The Speaker connection on the 56-pin JAMMA connector is for the Left

the wires from pins K and 10 of the JAMMA connector to the Left speaker, using the Yellow/Red wire to the positive (+) terminal, and the Yellow/Green wire to the negative (-) terminal,

  • On stereo cabinets, connect wires from pin Al of the Extended (48-pin) connector to positive (+) terminal of the Right speaker, and from B1 to the negative (-) terminal. Use a DDK 225-100242-2314 connector to mate with the 48-pin connector
  • Ifyou are installing in a mono cabinet, enter Test Mode (by setting DIP SW1 to On) and select “Mono” from the Game Options Screen. Leaving the sound set to Stereo in a mono cabinet will not affect game playability. Refer to Table 5-1 for more information regarding connector wiring.

5.1.4 Installing the FCC Ferrite Clamp Open the Ferrite Clamp and install it around the JAMMA harness as close to the Game PCB as possible.

Page 8

Operator’s Manual Great Sluggers™

5.2 Player Controls

Player 2, START Button j Player 1, START Button

Player 1, Joystick

Player 1, Button 1 -—~ Player 1, Button 2 Player 1, Button 3

Player 2, Butlon 1 t Player 2, Joystick

Player 2, Butfon 2 |— Player 2, Button 3 7

Figure 5-2 Player Control Panel

5.2.1 Modifying the control panel 1, Remove the overlay from the old control panel to provide a smooth clean surface on which to mount the new overlay,

  • Apply the Control Panel Overlay from the kit, and cut openings in it to match the control panel holes,
  • As an option, cut a piece of acrylic as shown in Figure 5-2, or use the existing cabinet control panel as a guide. 4, Using the Control Panel Overlay as a guide, cut and drill mounting holes for the Start buttons, Joysticks, and Player buttans.
  • Mount the Start Buttons, Joysticks, and Player Buttons as shown in Figure 5-2. Remember to place the Button ID Tags on the Buttons before mounting them. Besure to install the ID Tags because the game instructions refer to them.

§.2.2 Wiring the Control Panel Connect the JAMMA wiring harness to the controls as shown in Table 5-1.

6 © NAMCO-AMERICA, Ine. June 1994

Page 9

Great Sluggers™ Operator’s Manual

Solder Side Component Side

Wire Color

Black

Red

Red

Wire Color Description Terminal Description

GND

GND

Key Blue/Green Coin Counter 2

Blue/Red *Coin Lockout 2 Coin Counter 1 Red/Green

Yellow/Green Left Speaker (-) White/Green Audio Gnd

White . Video Sync

“Tilt switch Rll

ray wn *Coin Lockout 1

Test Mode Green/Blue Coin Switch 2 Bb n Coin Switch 1

Red/Yellow 2P Start Switch

Green/Yellow a N A

B

Cc

D

E

J

K

L

= =

Blue/Yellow

2P Left z[< Ble oo 1P Start Switch Red/White

1P Up Green/White

Black/Yellow

PihieYalow [2° Bovon? | | Orange/Yellow 2P Button 3 Gray/Yellow 2P Button 4 | Yellow/Black Black/White

Violet/White

Yellow/White

1P Button 3 Orange/White

1P Button 4

Undefined

GND

GND Be BIS

NININ

*Service Switch 2 | GND

GND

Table 5-1 JAMMA Connector Wiring

Page 10

Operator’s Manual Great Sluggers™

5.3 Graphics

NOTE:

The pressure sensitive decals have a protective covering on their backs which must be removed before applying. Take care regarding the position of the decals as they stick very tightly and, once they have been applied, cannot be easily removed.

5.3.1 Marquee Panel

  • Remove the existing marquee panel.
  • Trim the NAMCO GREAT SLUGGERS™ marquee to match the size of the existing marquee panel.
  • Place the NAMCO GREAT SLUGGERS™ marquee behind the acrylic marquee panel, and tape it at the top and bottom to secure it in place.
  • Replace the marquee and acrylic and mount securely with the existing cabinet hardware.

5.3.2 Monitor Bezel

  • Remove the glass panel protecting the monitor and remove the existing monitor bezel.
  • The new screen bezel is pre-printed on the back with guidelines for cutting out an opening based on most common game screens. Using the appropriate guidelines, or the old monitor bezel, cut the opening for the monitor.
  • Place the new screen bezel over the monitor face and add the NAMCO GREAT SLUGGERS™ Game Play instructions to the bezel. If possible, locate the instructions on the bezel below the monitor.
  • Replace the protective glass removed in step 1.

5.3.2 Cabinet Side Decals There are two Cabinet Side Decals provided in the kit, one left, and one right. Remove the protective backing from the NNMCO GREAT SLUGGERS™ side decals and carefully apply them to the cabinet.

Page 11

Great Sluggers™ Operator’s Manual

6.0 TEST MODE

The NAMCO GREAT SLUGGERS™ Game PCB includes a built-in Test Mode in help you verify that installation has been performed correctly before putting the game into service. To enter Test Mode, set DIP Switch 1 to the ON position (refer to Figure 5-1 for location). The Test Menu screen will be displayed.

FLIP [OFF] SWITCH Test SOUND Test COIN Options GAME Options UARTS Test OBJECT Test SCROLL Test A.D.S. COLOR Test CONVERGENCE Test RS 232 Test

. Figure 6-1 Test Menu Screen Use the Player 1 Joystick to select the desired item from the menu, then press the Player 1 A pushbutton to activate that choice. Press the Player 1 B Button to return to the Test Menu. Set the DIP Switch to the OFF position to return to normal game play. FLIP — Inverts the screen image, for use with cabinets with image-inverting mirrors. SWITCH Test — Selecting this option causes the Switch Test Screen to be displayed. SOUND Test ~ Selecting this option causes the Sound Test Screen to be displayed. COIN Options — Selecting this option causes the Coin Options Screen to be displayed. Game Options — Selecting this option causes the Game Options Screen to be displayed. UARTS Test — Not used. OBJECT Test — Selecting this option causes the Object Test Screen to be displayed. SCROLL Test — Selecting this option causes the Scroll Test Screen to be displayed. A.D.S. - Selecting this option causes the Game Data Screen to be displayed. Color Test — Selecting this option causes the Color Test Screen to be displayed for monitor adjustment. Convergence Test — Selecting this option causes the cross-hatch pattern screen to be displayed for monitor convergence adjustment. RS-232C Test — Not used.

Page 12

Operator's Manual Great Sluggers™

6.1 Switch Test Screen The switch test screen can be used to verify that installation has been performed correctly, or to diagnose and locate problems with the player controls.

0000 0000 +++ +44 +et +e+ +++ 0 +44 +++ 0 +44 ANALOGO: OOFF SERVICE SW: + ANALOG1 : OOFF TEST SW: + ANALOG2 : OOFF DIP 1: + ANALOG3 : OOFF

DIP 2: + ANALOG4 : OOFF

ANALOGS : OOFF ANALOG6 : OOFF ANALOG7 : OOFF

PADDLEO: 0000 PADDLE1 : 0000

Figure 6-2 Switch Test Screen

Page 13

Great Sluggers™ Operator’s Manual

6.2 Coin Options Screen The Coin Options Screen controls options related to game cost and the coin mechanisms. Numbers refer to items in Table 6-1.

COIN Options {Defaults in GREEN] Game Cost 2 Coin 1 Credit Discount to Continue Yes Coinl Mech Value 1 Coin Counts as 1 Coin Coin2 Mech Value 1 Coin Counts as 1 Coin Coin3 Mech Value 1 Coin Counts as 1 Coin Coin4 Mech Value 1 Coin Counts as 1 Coin Bonus for Quantity Buy In NONE FREE PLAY NO

Figure 6-3 Coin Options Screen

Page 14

Operator’s Manual

6.3 Game Options Screen Great Sluggers™

The Game Option Screen controls options related to game play such as difficulty level, music in attract mode, etc. Numbers refer to Table 6-1

t Difficulty Level: Medium Music in Attract: Yes Speaker Out: Stereo Credit Mode: Common Coin Counter: Type A Continue Inning 1 Inning Continue Inning 1 Inning Complete Credit 4 credits Complete Credit 8 credits Favorite Team None Watch Mode No <1

<2

<1

<2 >)

GAME Options [Defaults in GREEN]

Player>

Player>

Player>

Players>

Figure 6-4 Game Options Screen

Page 15

Great Sluggers™ Operator’s Manual

6.5 Option Settings Table | [item Description (<< indicates factory setting) Number of coins required for one game (1 credit) 1-9 (default is 2) 2 | Discount 50% Discount when continuing a game Coin 1 Mech | Count per coin 1-9 (default is 1) Coin 2 Mech Count per coin 1-9 (default is 1) [5 [conde [Soeued———Se

One additional coin per the specified number of coins

| 8 | Free Play NOx<< YES G Difficulty Medium<< (Easy - Medium - Hard) Attract Sound YES<< NO (B.G. music erasable only) Stereo << Mono COMMON (Credit is common to both players) EACH ONE << (Credit is separate for P1 and P2) A= 1 counter / B=2 counters<< Continue Inning 1-Player 1-3 Innings (default is 1 inning)

1-3 Innings (default is 1 inning)

Complete Credit 1-Player Complete Credit 2-Player Favorite Team NONE << (Atlanta - Toronto, 28 teams) Watch Mode NOx< YES 1-9 Credits (default is 4)

1-9 Credits (default is 8)

Table 6-1 Option Settings Table