Pole Position TM-218 5th Printing
Pole Position (World) (Namco, 1982) · Technical Manual · 92 pages · 57 sections · original scan
Operation, Maintenance, and Service Manual
Complete with Schematics and Illustrated Parts Lists
If reading through this manual does not lead to solving a certain maintenance problem, call TELEHELP® at the Atari Customer Service office in your geographical area, as shown below.
WEST and CENTRAL U.S.A. Parts and Service
Atari, Inc. California Customer Service Office 1105 N. Fair Oaks Avenue P. O. Box 427, Sunnyvale, CA 94086 Telex 17-1103 (Monday-Friday, 7:30-4:00 pm Facific Time) From California, Alaska, or Hawaii B. (408) 745-2900 Service from anywhere in the area shown in white @ oltre (800) 538-1611
EAST U.S.A. Service only
Atari, Inc. New Jersey Customer Service Office 12A World's Fair Drive, Somerset, NJ 08873 Telex 37-9347 (Monday-Friday, 7:30-4:00 pm Eastern time) From New Jersey @ (201) 469-5993 = From anywhere else in this area toll-free (800) 526-3849
EUROPE
Parts and Service
Atari Ireland Limited European Customer Service Office Tipperary Town, Ireland Telex 28165 TIPPERARY TOWN, (Monday-Friday, 9:00-6:00 pm GMT) IRELAND BZ 06252155
Operation, Maintenance, and Service Manual
Complete with Schematics
and lilustrated Parts Lists
*Pole Position is engineered and designed by Namco Ltd. Manufactured under license by Atari, Inc.
Pole Position
© 1982 by Atari, Inc. All rights reserved. No part of this publication may be reproduced by any mechanical, photographic, or electronic process, or in the form of a phonographic recording, nor may it be stored in a retrieval system, transmitted, or otherwise copied for public or private use, without permission from the publisher. The game play, all graphic designs, this technical manual, its accompanying schematic diagrams, and the display manual are protected by the U.S. Copyright Act of 1976. This Act provides for increased penalties for violating federal copyright laws. Courts can impound infringing articles while legal action is pending. If infringers are convicted, courts can order destruction of the infringing articles. In addition, the Act provides for payment of statutory damages of up to $50,000 in certain cases. Infringers may also have to pay costs and attorneys’ fees, fines up to $25,000, and face an imprisonment of up to one year. Atari will aggressively enforce its copyrights against any infringers. We will use all legal means to immediately halt any manufacture, distribution, or operation of a copy of video games made by us. Anyone who purchases such copies risks forfeiting such a game.
Published by’ ATARI, INC. 790 Sycamore Drive P.O. Box 906 Milpitas, California 95035
Lithographed in the U.S.A, 4M
Notice Regarding Non-ATARI Parts
Use of non-ATARI parts or modifications of your ATARI® game circuitry may adversely affect the safety of your game, and may cause injury to you and your players.
You may void the game warranty (printed on the inside back cover of this manual) if you do any of the following:
substitute non-ATARI parts in the game modify or alter any circuits in the game by using kits or parts not supplied by Atari.
INTERFERENC
to licensed communications services is not permitted by the Federal Communications Commission (FCC). \f you suspect interference from an ATARI® game at your location, check the following: all green ground wires in the game are properly connected as shown in the the game wiring diagram the power cord is properly plugged into a grounded 3-wire outlet the game PCB is properly installed within the Electromagnetic !nterference (EMI) cage the EMI Shield PCB is properly installed and in series with the game PCB harness. Refer to Figure 3-18 to make sure that the game PCB and the Shield PCB are correctly installed. If you are still unable to solve the interference problem, please contact ATARI Customer Service. See the inside front cover for service in your area.
Pole Position
Table of Contents
1 sete Procedures New Features Inspecting the Game ..... Leveling the Sit-Down Cabinet. . Space and Power Requirements .
- Installation Requirements. . .
- Selecting the Voltage Plug . Locating the Switches ....
- Power On/Off Switch .
- Utility Panel Switches .
- Option Switches ...
- Memory Back-Up Jumper . . Setting the Option Switches . Performing the Initial Self-Test Game Play
- Attract Mode . 2.Play Mode ....
- High-Score Mode ..
- Hints for Game Play gom>
m
zom
- Self-Test Procedure A. Commenis on Troubleshooting B. Performing the Self-Test
3 Maintenance, Repair, and Parts
Player Controls ............0s eee eee Fluorescent Tube and Speaker Replacement Video Display oO Utility Panel. Coin Doors .. Printed-Circuit Boards . . Power Supply Assembly ranmoom>
Glossary of Terms .......0..00.0.0 0.0... cee ce eee ce eee es » 110 » 112
- 1-12 » 12 . 143
Cabinet-Mounted Assemblies .............2....000e 1-13
Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4
Figure 1-5 Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4
Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4
Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8
Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12
Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16
Figure 3-17 Figure 3-18 Figure 3-19 Figure 3-20
Figure 3-21 Figure 3-22 Figure 3.23 Figure 3-24
Table 1-1 Table 1-2 Table 1-3 Table 1-4
Table 2-1 Table 2-2 Table 2-3 Table 2-4 Pole Position
List of Illustrations
Game Overview, Upright Cabinet .... 1-2 Game Overview, Sit-Down Cabinet . 1-3 Leveling the Sit-Down Cabinet .. 16 Location of Game Switches 16
Self-Test Display . . 1-11 Self-Test Screen 1: Uprig 23 Self-Test Screen 1: Sit-Down Test Passes . 23 Self-Test Screen 1: Test Fails ........ 23 Self-Test Screen 2.0.0.6... cece eect teens 2-4 Illustrated Parts Lists Cabinet-Mounted Assemblies, Upright Cabinet .............. 32 Cabinet-Mounted Assemblies, Sit-Down Cabinet . 3-4 Control Panel 37 Control Panel Assembly 38
Steering-Wheei Control Assembly .... - 310 Steering-Wheel Control Screw Adjustmen . 312 Steering-Wheel Control Orientation ... - 313 Gear-Shifter Control Assembly... 2.0.0... 000 c cece eee 3-14
Foot-Pedal Control Assembly 3-16 Foot-Pedal Cable Rewinding . » 3-18 Fluorescent Tube and Speaker! Board Rem pright ‘Gabi net 3-20 Fluorescent Tube and Speaker Board Assembly Upright Cabinet 3-21 Sit-Down Cabinet Speaker Removal ............ 0.0.0 0es eee 3-22 Video Display ................ . 3-25 Utility Panel Assembly . .. . . 3-26 Vertically Mounted Coin Door . . 3-28
American-Made Coin Door 3-31 Removing the Printed-Circuit Board: 3-34 Central Processing Unit Printed-Circuit Board Assembly . 3:36 Pole Position Video Printed-Circuit Board Assembly.......... 3-44
Regulator/Audio 11 PCB Assembly, U.S.-Buiit Cabinet ......... 3-49 Regulator/Audio Il PCB Assembly, Ireland-Built Cabinet . 3-50 EMI Shield PCB Assembly... .........6..0.000 eae . 353 Power Supply Assembly
List of Tables
Switch Settings for Game and Price Options ...............- Switch Settings for Game and Play Options . . i9 Self-Test Procedure ........... . 1:10 Qualifying Lap Information ................0005 1-13
Locating Failed Components on the Video PCB ............ 2-2 Locating Failed Components on the CPU PCB ... 22 Locating the Failed ROM .. 2-3 Locating the Failed RAM .. 2-4
Pole Position
vi
NOTICE
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipmeni in a residential area is likely to cause interference in which case the user, at his own expense, will be required to take whatever measures may be required to correct the interference.
Set-Up Procedures
How to Use this Manual
This manual, written for game operators and service technicians, describes the Pole Position game. The manual contains information about the Upright and Sit-Down Pole Position cabinets. Whenever information is unique to the Upright cabinet, this symbol appears: |
Whenever information is unique to the Sit-Down
cabinet, this symbol appears: r 2)
Wherever information is unique to /reland-Built
games, this symbol appears: 7
Chapter 1 describes new features, game setup, settings of option switches, self-test procedures, and game play. Chapter 2 contains self-test procedures. Chapter 3 details maintenance, repair, and parts information. A glossary of terms is in the back of this manual for your convenience. In addition, schematic diagrams of the game circultry are included with this manual. Figures 1-1 and 3-1 illustrate the Upright game cabinet; Figures 1-2 and 322 illustrate the Sit-Down game cabinet. Italicized lettering on these figures refers you to other places in the manual for information about specific cabinet parts.
Set-Up Procedures
ATTRACTION PANEL, FLUORESCENT TUBE AND SPEAKER See Figure 3-11 or 3-12 Pole Position
% GAME IDENTIFICATION LABEL (Serial number appears here on Ireland-Built games)
+ VIDEO DISPLAY See Figure 3-14 ACCESS PANEL > \ DASHBOARD
STEERING-WHEEL See Figure 3-1
CONTROL ASSY. See Figure 35 2 " ASS P Hill GAGE + GAME PCBs 7 ee See Figures 3-18, 3-19 & 3:20
GEAR-SHIFTER CONTROL ASSY. See Figure 3-8 UTILITY PANEL ,GR nor! See Figure 3-15 0 It PCBs
9 CAPACITOR See Figures 3-18,
See Figure 3:24 “ard aee
CONTROL PANEL A See Figures 3-3 & 3-4
SPEAKER See Figure 3-12
- POWER SUPPLY POWER ON/OFF SWITCH COIN DOOR See Figures 3-16 & 3-17 See Figure 324
FOOT-PEDAL ASSEMBLY oo See Figure 3-9
x Items with a serial number label on U.S.-Built cabinets
SHOCK HAZARD This game should only be connected to a grounded 3-wire outlet. lf you have only a 2-wire outlet, we recommend you hire a |icensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded!
Figure 1-1 Game Overview
Upright Cabinet
1-2
Pole Position Set-Up Procedures
- GAME IDENTIFICATION LABEL (Serial number appears on exterior of rear access panel of ireland-bullt games)
- GAME PCBs See Figures 3-18, UTILITY PANEL ASSY. 3-19 & 3-20 See Figure 3-15 SPEAKER EMI CAGE See Figure 3-13 See Figures 3-18 & 3-23
ATTRACTION PANEL / See Figure 32
ACCESS PANEL
% REGULATOR! AUDIO 1] PCBs See Figures 3-78, 321 & 3-22 POWER ON/OFF SWITCH
- POWER SUPPLY
CAPACITOR See Figure 3-24
See Figure 3-24
- VIDEO DISPLAY See Figure 3-14
STEERING-WHEEL CONTROL ASSY. See Figure 3-5
GEAR SHIFTER CONTROL ASSY. See Figure 3-8
CONTROL PANEL See Figures 33 & 3-4
COIN DOOR See Figures 3-16 & 3-17
SHOCK HAZARD See Figure 39 This game should only be connected to a grounded 3-wire outlet. If you have only a 2wire outlet, we recommend you hire a licensed electrician to install a grounded outlet. You may receive an electrical shock if the game is not properly grounded! x Items with a serial number label on U.S.-Built cabinets
Figure 1-2 Game Overview Sit-Down Cabinet
4-3
Set-Up Procedures
A. New Features
The Pole Position game has many new features. Even if you are familiar with ATARI® games, you should note these important differences: @ Electromagnetic Interference (EMI) Cage in U.S.-Built Cabinets Only. Games built after December 1, 1982, will have the CPU and Video Printed-circuit boards (PCBs) mounted inside this cage. The EMI cage reduces interference from the game to television and radio receivers. See Figure 3-18 for details. @ American-Made Coin Door. Your game may be equipped with a new coin door. This door is very similar to the vertically mounted coin door, but does not have lockout coils. When ordering parts for your coin door, please check coin door illustrations In Figures 3-16 and 3-17 carefully to make sure you are ordering the correct part number. @ Steering-Wheel Control. This steering wheel is designed to provide a more realistic response from the race car on the display. @ Foot-Pedal Control (Accelerator and/or Brake). These pedals have been redesigned to accommodate a snap-action switch for the brake anda potentiometer, turned by a spring and cable, for the accelerator. @ Metal Attraction Panel on Sit-Down Game Cabinet. The metal attraction panel mounted on top of the cabinet entices players with its Formula-1 racing graphics. ®@ Quadraphonic Sound in Sit-Down Cabinet. Four 4ohm, 6-ounce, high-fidelity speakers (two under the control panel; two behind the seat) surround the player with the exciting and realistic sounds of Gran Prix racing. New features and other major parts of the game are shown in Figures 1-1 and 1-2. Throughout this manual, wherever a new feature is mentioned, you will see this symbol: Pole Position
B. Inspecting the Game
it
1.
2. Please inspect your game carefully to ensure that was delivered to you in good condition.
Examine the exterior of the game cabinet for dents, chips, or broken parts. Remove the screws that were used as extra security to seal the rear access panel. Unlock and open this panel and the coin door; inspect the interior of the game as follows: a. Ensure that all plug-in connectors (on the game harness) are firmly plugged in. Replug any connectors found unplugged. Do not force connectors together. The connectors are keyed so they only fit in the proper orientation. A reversed edge connector may damage a PCB and will void your warranty. b. Ensure that all plug-in integrated circuits are firmly plugged into their sockets on the printed-circuit boards (PCBs). c. Remove the tie-wrap that secures the coiled power cord inside the cabinet. Inspect the power cord for any cuts or dents in the insulation. Repair or replace it as required. Place the square black plastic strain-relief plate in the wood slot at the bottom of the rear panel opening. d. Note the game serial number printed on a label on the back of the cabinet. Verify that the same serial number is also on the Pole Position game PCBs, Regulator/Audio II PCBs, power supply, and video display. See Figures 1-1 and 1-2 for \ocations of the serialnumbered components. Please mention the serial number whenever you call your distributor for service. e. Inspect major subassemblies, such as the power supply, control panel, and video display. Make sure they are mounted securely.
Pole Position
- For the Sit-Down cabinet, remove the metal attraction panel from the protective wrapping. Remove the three button-head screws and retainer on the front window. Place the attraction panel over the mounting holes. Reinstall the retainer and screws.
C. Leveling the Sit-
C. Leveling the Sit Down Cabinet
The Sit-Down cabinet rolls easily from location to location on 4-inch casters. To level! the cabinet, lift the game up on one side. Place a block of wood, a book, or another object (that is at least 2-inches thick) under the raised cabinet. Partially unscrew the adjustable glides (see Figure 1-3) until they extend beiow the caster. Lower the game and lift it up on the other side; partially unscrew the adjustable glides. Lower the game. To prevent players from moving the game around, be sure to adjust all four glides.
CASTER ADJUSTABLE GLIDE -
Figure 1-3 Leveling the Sit-Down Cabinet Set-Up Procedures
D. Space and Power Requirements
- Installation Requirements
Power 250 W Temperature 0° to +38°C (+ 32° to + 100°F) Humidity Not over 95% relative Upright Cabinet Space Required 62 x 90 cm (25% x 35% in.) Game Height 186 cm (72% in.) Sit-Down Cabinet Space Required 165 x 64 cm (65 x 25% in.) Game Height 194 cm (76 in.)
- Selecting the Voltage Plug
The power supply used in this game operates on the line voltage of almost any country in the world. The power supply comes with either one, two, or three separate voltage-selection plugs. Plug voitages and wire colors are 100 VAC (violet wire color), 120 VAC (yellow wire color), 220 VAC (blue wire color), and 240 VAC (brown wire color). Before plugging in your game, check your line voltage. Next, check the wire color on the voltageselecion piug that is plugged into the game’s power supply. Make sure the voltage-selection plug is cortect for the voltage of your location (see Figure 3-24). Now, plug the game into a grounded 3-wire outlet.
Set-Up Procedures
E. Locating the Switches
Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls. Pole Position
- Power On/Off Switch
The power on/off switch is located on the back of the Upright cabinet on the lower left side. On the Sit- Down cabinet the power on/off switch is located on the lower left side of the cabinet (see Figure 1-4).
OPTION SWITCHES SWITCH AT 9JA (Game and price) SWITCH AT 9L (Game and play)
information.
JUMPER AT 6B (Memory back-up) See CO-218-01 for NAMCO PCB UTILITY PANEL ASSY. See Figure 3-15
POWER ON/OFF SWITCH
Figure 1-4 Location of Game Switches
Pole Position
- Utility Panel Switches The volume Control(s), self-test switch, coin count: er(s), and auxiliary coin switch are located on the utility panel in both the Upright and Sit-Down cabinets (See Figure 3-12). The utility panel is located inside the upper coin door. The volume control(s) adjust the level of sound produced by the game. The Sit-Down cabinet has four volume controls: one for each speaker. The Upright cabinet has two volume controls: one for each speaker. The self-test switch is used to enter and exit the Self-Test Mode. The coin counters) record the number of coins entered into the game. The auxiliary coin switch is used to credit the game without activating the coin counter(s).
- Option Switches Option switches are iocated on the game CPU PCB (see Figure 1-4). Refer to supplement CO-218-01 for switch locations if your game has NAMCO PCBs.
a. Game and price options are at CPU PCB location QJA. b. Game and play options are at CPU PCB location 9L.
- Memory Back-Up Jumper The memory back-up jumper is at CPU PCB location 6B. Position this jumper to the on setting. The memory back-up jumper is positioned on the off setting when shipped from the factory to prevent leakage and to provide ionger life for the battery at location 6A on the CPU PCB. The jumper must be Positioned to the on setting so that the battery can Provide power to the CMOS memory. This memory stores the high-Score table and operator statistics. Set-Up Procedures
The jumper does not affect game play. We recommend you position this jumper to the off setting when you expect extended downtime.
F. Setting the Option Switches
Settings of the game option switches are explained in Tabies 1-1 and 1-2. Options preset at the factory are shown by the < symbols. However, you may change the settings according to your individual needs. To verify option-switch settings, first set the power on/off switch to the off position and then to the on position. Next, set the self-test switch to the on position. Compare the information on the screen to the option switch settings listed in the tables in this section. Then set the self-test switch to the off position. Table 1-1 describes the switch settings for options relating to game price, coin mechanism multipliers, number of laps per game, and number of seconds per lap. These switches are on the game CPU PCB at location QJA. The multipliers (QJA switches 1-5) determine the value of the coin mechanisms to the game’s logic. A coin mechanism is a device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. The mechanism either accepts or rejects the coin. The coin door has two coin mechanisms. The basic unit of measurement is a coin worth $.25 or 1 DM, which equals a multiplier of x1. For example, if you have a2 DM/1 DM coin door, you may want to Set the left multiplier at x2 and the right multiplier at x1.
Set-Up Procedures
| Coin | Option | Interconnect | Assembly |
J55A-P55A permits a coin placed in either coin mechanism to register in the same coin counter. The cable connector is located between the coin door harness and the main harness (see the Coin Op-
| tion | Interconnect | Wiring | Diagram | in | ||
| SP-218). | When | it | is | used, | left | coin |
mechanism option switches at 9JA apply to both coin mechanisms. If you want different options for the left and right coin mechanisms, remove Coin
| Option | Interconnect | Assembly | J55A- |
P55A and connect J55 directly to P55. If you have NAMCO game PCBs, refer to CO-218-01 for the location of the option switches. Pole Position
Table 1-1 Switch Settings for Game and Price Options
Sottings of 8-Toggle Switch on Pole Position CPU PCB (at 9A)
| 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 |
Option
On 4 racing iaps * Off 3 racing laps <
Off Off
Off On
On Off On On
On Off On On
Oft Off
On Off On Oft On On On On Off On Off
On Off On Off On 90 seconds per lap <4 100 seconds per lap 110 seconds per lap 120 seconds per lap *
Right Coin Mechanism 1 coin for 1 credit < 2 coins for 1 credit * 3 coins for 2 credits 4 coins for 3 credits
Left Coin Mechanism 1 coin for 1 credit 1 coin for 2 credits 1 coin for 3 credits
2 coins for 1 credit * 3 coins for 1 credit 3 coins for 2 credits 4 coins for 3 credits * Free Play
4Manufacturer’s recommended settings for Upright cabinet % Manufacturer's recommended settings for Sit-Down cabinet *This option setting can be changed to 1 coin for 6 credits by changing the program PROM (136014-160). Contact your distributor for further information,
Pole Position
We recommend that game difficulty for the race laps (EXTENDED RANK) and the qualifying lap (PRACTICE RANK) be increased periodically. These changes will ensure that Pole Position continues to offer maximum excitement and challenge. Except in locations with extremely skillful and advanced players, these settings should not be increased more than one level per month. Set-Up Procedures
Table 1-2 contains option-switch settings for Attract Mode sound and speed (kilometers or miles per hour). These switches are on the game CPU PCB at location 9L. Pole Position leaves the factory with option switches set at the manufacturer’s recommended difficulty level. The game will be exciting and challenging for players at these settings. Table 1-4 lists the manufacturer's recommended qualifying lap times. Table 1-5 lists option-switch settings for additional qualifying lap times. Table 1-6 provides switch settings for racing lap times.
Table 1-2 Switch Settings for Game and Play Options
Refer to CO-218-01 for switch locations if your garne is equipped with NAMCO PCBs.
Settings of 8-Toggle Switch on Pole Position CPU PCB (at 9L)
8 7 6 5 4 3 2 1 Option
Off On
Off On Attract Mode sound off Attract Mode sound on
Kilometers per hour Miles per hour ~<
{Manufacturer's recommended settings
Set-Up Procedures
G. Performing the Initial Self-Test
This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speakers. No additional equipment is necessary. Wait at least 10 seconds after playing a game before switching to the Self-Test Mode. Otherwise, you may erase the top three scores in the high-score table or distort the statistics. All credits will be cancelled when you switch to self-test. Refer to Figure 1-4 for the location of the option switches and Figure 3-15 for the location of the selftest switch. Set the self-test switch to the on position (see Figure 71-5) to see the Self-Test Display in the Self-Test Mode. To exit the Self-Test Mode, set the self-test switch to the off position. Pole Position
The complete self-test procedure is explained in Chapter 2, B. Self-Test Procedure. If a part of the test described in Table 1-3 fails, refer to Chapter 2. We suggest you perform the self-test procedure when you first set up the game, when you collect money from the game, when you change game options, or when you suspect game failure.
Do not depress the accelerator or brake pedal when turning on the game or switching to the Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls,
Table 1-3 Self-Test Procedure
Instruction Test Passes
- Without touching the pedal(s), set the self-test switch to the on position. All credits will be cancelled.
. Press down on the accelerator pedal.
. Press down on the brake pedal of the Sit-Down cabinet.
. Turn the steering wheel clockwise, then counterclockwise.
. Shift the gear shifter.
. Shift the gear shift, press the auxiliary coin switch, and activate the coin switches.
. Press the auxiliary coin switch.
. To end the test, switch the self-test switch to off. Random symbols are displayed on the screen for about five seconds, The self-test display appears. RAMs and ROMs are tested. If the screen is different from the self-test display, or if there are sounds, refer to Chapter 2, Self-Test Procedure.
The numbers to the right of ACCEL increase from 00 to somewhere between 80 and AQ as you press down on the pedal. If the test fails refer to Chapter 2.
The numbers to the right of BRAKE switch from 00 to FF. For the Upright cabinet, the numbers to the right of BRAKE should always read 00. If the test fails, refer to Chapter 2. Rotating the wheel clockwise causes the numbers to the right of STEER- ING to increase. Rotating the wheel counterclockwise causes the numbers to decrease. If the test falis refer to Chapter 2.
The words to the right of SHIFT change from LO (shifter up) to H/ (shifter down) as you shift gears. If the test fails, refer to Chapter 2.
The numbers to the right of SOUND increase from 00 to 20, and a new sound is played with each number. Test all 20 sounds. If the test fails, refer to Chapter 2.
Game statistics appear (for a few seconds) at the bottom of the screen. Press the coin switch each time you want to see the statistics. To erase game statistics, simultaneously press down on the accelerator pedal and press the auxiliary coin switch twice. Statistics will be reset at /999/. To reset the high-score table, simultaneously press down on the accelerator pedal and change gear shifter from low to high. The high-score table will be reset and contain fictitious scores.
1-10
Pole Position Set-Up Procedures
ALL RAMS GOOD ALL ROMS GOOD
ACCELERATOR PEDAL BRAKE PEDAL
STEERING ; : WHEEL STEER SHIFT LO ———— ceansnirten
SOUNDS : LEFT COIN
MECHANISM
RIGHT COIN MECHANISM QUALIFYING au LAP TIME ———— TIM NO. OF LAPS IN THE RACE
RA rE CF DIFFICULTY LEVEL__> EX TENDED QUALIFYING LAP g DIFFICULTY LEVEL (See Table 1-2)
_¢-———. GAME STATISTICS
GAME AUTOMATICALLY STARTS* (When correct number of soing are Inserted) THE COUNT STARTS AT 999(999) AND DECREASES. For example, if you play 10 games, the game subtracts 10 from 99.9, and the display shows 98.9 for the number of games piayed. (Disregard decimal points.)
NO. OF GAMES PLAYED NO. OF POINTS SCORED (x19) NO. OF SECONDS PLAYED NOT APPLICABLE
999. 999, 999. 999, 999, 999. 999. 999. 999, 999, 999, 999. 999. 999. [ne | en | eee NO. OF SECONDS THAT GAME HAS BEEN POWERED ON NO. OF GAMES IN WHICH
NO. OF GAMES IN WHICH PLAYER REACHED FINISH LINE PLAYER HAS QUALIFIED NO. OF GAMES THAT REACHED NO. OF GAMES THAT REACHED THIRD EXTENDED LAP “if screen displays MANUAL START, FIRST EXTENDED LAP
Suspect the game harness. NO. OF GAMES THAT REACHED Refer to the Schematic Package. SECOND EXTENDED LAP
Figure 1-5 Self-Test Display
Set-Up Procedures
H. Game Play
Pole Position is a one-player game using a color raster-scan video display. The game action takes place at Fuji Speedway in Japan. The country around the speedway consists of green meadows, hills, and snow-capped Mt. Fuji. The player drives a Formula-1 race car on the Fuji Speedway. Player controls consist of a steering wheel, a two-position gear shifter, and accelerator and brake pedals on the Sit-Down cabinet (accelerator only on the Upright cabinet). The object of the game is to finish the qualifying lap as quickly as possible. !f the player beats the clock, he qualifies for the Gran Prix at Fuji Speedway; if not, he drives out the remainder of his time along the qualifying course, As a qualifier, the driver is ranked according to his qualifying lap time, from position one (the pole position) to position eight. The player then races against the clock and other cars to finish the four laps (operator-selectable option) of the race as fast as possible and to achieve the highest score possible. The player earns points for passing cars, driving on the track, and finishing the race with time remaining. He is rewarded with an extended-play lap for completing a lap. Pole Position has four modes of operation: Attract, Play, High-Score, and Self-Test. Self-Test is a special mode for checking the game switches and computer functions. You may enter the Self-Test Mode from any other mode. However, all credits will be cancelled. Pole Position
bite
- Attract Mode
The Attract Mode begins when you set the power on/off switch to on or after the Play, High-Score, or Self-Test Modes. The Attract Mode ends when the correct amount of credit for a game is inserted or when the Self-Test Mode begins. When the Attract Mode begins, the game displays a picture with the words POLE POSITION flashing at the top of ihe screen. A map of Fuji Speedway is displayed in the center of the screen. Within the map are the words FUJ/ SPEEDWAY and 71 LAP 3459M. At the bottom of the screen is the copyright message. Then, the Attract Mode simulates game play. Eight cars are at the starting line. The player's car, located in the eighth position, flashes on the screen. The starting lights flash from red to green and the race starts. The race continues until the player’s car crashes into another car and explodes into a red ball of fire. Then, the car reappears on the screen and continues down the track until it hits a sign along the side of the road. Again, the car explodes. During this sequence, the message GAME OVER appears in the center of the screen. Finally, the Attract Mode displays the High-Score Table. The fastest lap time, average game speed, and prize winners appear at the top of the screen. Below this information is a list of the six highest scores. Opposite each score are the initials of the player who achieved that score.
- Play Mode The Play Mode begins when the correct amount of credit for a game is recorded. The game starts with the player’s car behind the starting line and 90 seconds on the clock. (See Section E to select a different clock setting.) The car must finish the qualifying lap within 73 seconds to be in the race. {f the player does not qualify, his car continues on the track until 90 seconds are used up.
Pole Position
Table 1-4 Qualifying Lap Information
POSITION QUALIFYING LAP TIME‘ BONUS POINTS
| 1 | 58” 50 | 4000 |
| 2 | 60” 00 | 2000 |
| 3 | 62” 00 | 1400 |
| 4 | 64” 00 | 1000 |
| 5 | 66" 00 | 800 |
| 6 | 68” 00 | 600 |
| 7 | 70” 00 | 400 |
| 8 | 73” 00 | 200 |
“in seconds and hundredths of a second & The above times apply to manufacturer's recommended settings. Just before the race begins, the player’s car (flashing on the screen) is placed at the starting line with seven other cars. The position of the car depends on the qualifying time as shown in Tables 1-4 or 1-5. The starting lights flash from red to green, and the race begins. Racing hazards are other racing cars, sharp turns, and road signs. As the race progresses, more cars appear on the track. If the driver’s car hits another car or a road sign, the driver's car is destroyed in an explosion. The driver's car reappears in a few seconds and the race continues. Driving through wet puddles or off the track siows down the driver's car. Racing into the first turn, the driver must let up on the accelerator slightly to make the corner. Road signs flash along the side of the track. Depending on how well the player manipulates the controls, he can either roar through the hairpin turns like a champion or spin out in a flaming crash. He jockeys for position with the other racers, while keeping his eye on the clock at the top of the screen. When his time runs out, the race is over. The top score achieved by a player appears at the top of the screen. The time alloted for the lap is displayed under the top score. Increasing lap time (in seconds and hundredths of a second) and the speed of the car appears last. Set-Up Procedures
- High-Score Mode The High-Score Mode begins when a player has earned one of the 300 highest scores. The player has one minute to record his initials. A player rotates the steering wheel to locate his initial. He presses a foot pedal to put his initial on the screen. The third time he presses the pedal his initials are transferred into the high-score table.
- Hints for Game Play © Avoid puddles and the sides of the track because these slow you down. © Accelerate and stay ahead of other racers. Stick to the inside of the track to make the corners. © Successful completion of a turn depends on braking skill.
- When sliding, steer into the skid.
ae
Tang O
ae —— i
1-13
Pole Position Set-Up Procedures
Table 1-5 Switch Settings for Qualifying Lap Times
| 9L | Self-Test | Level | |
| Option | Practice | of | Beat This Many Seconds |
| Switches | Rank | Difficulty | to Qualify for Position: |
1 2 3 1 2 3 4 5 6 7 8
| On Off On | F | Easy | 66 68 70 73 75 7 80 82 |
| Off Off On | E | 65¥%2 67% 70 72%2 7A4ve 76¥2 79 81 | |
| On On On | H | 59% «61 63 66 68 70 72 75 | |
| On On Off | D | 59 61 63 65 67 69 71 74 | |
| Off On Off | c< | 58% 660 62 64 66 68 70 73 | |
| On Off Off | B | 58 60 62 64 66 68 70 72 | |
| Off Off Off | A | S7¥ 69 61 63 65 67 69 71 | |
| Off On On | G | Hard | 57 59 61 63 65 67 69 71 |
4Manufacturer's recommended settings
Table 1-6 Switch Settings for Racing Lap Times
| 9L | A Self-Test | Top Speed | Number of Seconds |
Option Option
Switches Switch Extended
4 5 6 8 Goal Rank MPH KPH Lap1 Lap2 Lap 3 Lap 4 Off Off Off Off 3 A 195 313 75 50 61 - Off Off Off On 4 A 195 313 75 53 58 62 Off On Off Off 3 Cc 195 313 75 48 60 - Off On Off On 4 c 195 313 7 51 57 61 On Off Off Off 3 Ba" 195 313 75 46 59 ml On Off Off On 4 Bat’ 195 313 7 49 56 60 On On Off Off 3 D 195 313 75 44 58 ad On On Off On 4 D 195 313 7 47 55 59 Off Off On Off 3 E 225 360 75 48 60 = Off Off On On 4 E 225 360 7 51 57 61 On Off On Off 3 F 225 360 75 46 59 - On Off On On 4 F 225 360 75 49 56 60 Off On On Off 3 G 244 391 75 48 60 _ Off On On Gn 4 G 244 391 ve) 51 57 61 On On On Off 3 H 244 391 75 46 59 = On On On On 4 H 244 391 75 49 56 60 “<Manufacturer's recommended settings *Upright cabinet **Sit-down cabinet
1-14
Self-Test Procedure
The reference designators for components in this chapter refer to games with Atari® PCBs. If you have Namco Q PCBs, please refer to CO-218-01.
The following self-test procedures should be performed by a qualified electronic technician. This game tests itself when the self-test switch is set to the on position. If there is a failure, the game produces audiovisual aids to help you find the failing portion of the game. The self-test procedure included in Chapter 1 will help you decide if the game is working properly.
Chapter
Self-Test Procedure
A. Comments on Troubleshooting
When troubleshooting, first determine the symptom(s) of the failure. After determining the symptom, look over the wiring diagram and determine what assemblies could cause the failure. Could it be caused by the power supply, Regulator/Audio II printed-circuit board (PCB), or the video display? The next step is to check all harness wires and connectors to the suspected assembly. If you do not find a harness or connector problem, substitute an assembly known to be good for the suspected failing assembly. If the game functions properly, you have successfully isolated the failure. If it doesn’t, repeat the procedure with another assembly. When you have isolated the failing assembly, you must troubleshoot that assembly and make the necessary repairs. If the video display fails, we suggest that a qualified video-display technician handle the troubleshooting and repair. Be sure to refer to The Book—A Guide to Electronic Game Operation and Servicing, published by Atari, Inc., whenever you need help with the techniques, tools, and terminology associated with coinoperated electronic games. To effectively troubleshoot a game PCB, learn as much as you can about the PCB. The diagrams in the Schematic Package (included with the game) show the functions of the circuitry. Again, while troubleshooting a PCB, first determine the symptom of the failure, then locate the suspected area on the schematic diagram. Tables 2-1 and 2-2 are troubleshooting aids, which can be used to locate faulty components.
Table 2-1 Locating Failed Components Pole Position
Table 2:2 Locating Failed Components on the CPU PCB
Custom AtoD
Symptom Area PROM 1C RAM Converter
Audio Voice 9c 9D Screech/Crash 9E Player's Motor 12E,12F Ail Other Sounds 7L,11D 7K,75 Inputs. Brake and/or Accelerator 8d Steering 9K Option Switches 9K,9M All Other Inputs om Control for Audio & Inputs 8H,9H Sync 7M High Scores 7E
on the Video PCB
Symptom Area PROM Custom RAM
Large Car Pictures 12J,130 Large Sign Pictures 12K,13K,12L, 13L Small Cars & Signs 12N,13N All Cars & Signs 12H,11N 13H 9F,10F Alphanumerics 7N,8M 8N Raceway 2L,2M,2N,4L 3N Background 6N,5K Raceway & Background 5L,6L Middle & Sides of Raceway 2B,2C,2D All Video AD,7E,2F Red ME Green 11D Blue alte]
B. Performing the Self-Test
This game will test itself and provide data to show that the game’s circuitry and controls are operating properly. The data is provided on the video display and speaker. No additional equipment is necessary. Video game repair should only be performed by a qualified electronic technician. To begin the Self-Test Mode, set the self-test switch, which is located on the utility panel, to the on position.
Do not depress the accelerator or brake pedal when turning on the game or switching to thé Self-Test Mode. This will cause faulty program initialization and incorrect action of the player controls.
Pole Position
SELF-TEST SCREEN 1—Test Passes: Upright Cabinet. If the test passes, the screen displays the picture in Figure 2-1, Upright Test Passes. See Chapter 1, Section G, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off and immediately back to on.
Figure 2-1 Self-Test Screen 1:
Upright Test Passes
Sit-Down Cabinet. If the test passes, the screen displays the picture in Figure 2-2, Sit-Down Test Passes. See Chapter 1, Section G, Performing the Initial Self-Test for a complete description of this picture. To see self-test screen two, set the self-test switch to off and immediately back to on.
AUTO STi
Figure 2-2 Self-Test Screen 1: Sit-Down Test Passes Self-Test Procedure
SELF-TEST SCREEN 1—Test Fails: If the test fails, the screen may display the picture in Figure 2-3, Test Fails.
Figure 2-3 Self-Test Screen 1: Test Fails
ROM failure is indicated by the word ROM and a pair of alphanumeric characters displayed at the top of the screen.
Table 2-3 Locating the Failed ROM
Location on Location on ROM No. ATARI CPU PCB = NAMCO CPU PCB
| 0 | 7H | 6H |
| 1 | TF | 5H |
| 2 | SL | 8M |
| 3 | 4L | 8L |
| 4 | 3K | 7™ |
| 5° | 4K | 7L |
6 4M
| 7 | 4E | 4u |
| 8° | 30 | 3M |
| 9° | 4D | 3 |
*Not used
Self-Test Procedure
RAM failure is indicated by the word RAM anda pair of alphanumeric characters displayed at the top of the screen. Table 2-4 lists the failed RAM chip, the printed-circuit board (PCB) the chip is on, and the chip’s location. Replace the failed RAM, and restart the test (set the self-test switch to off, and then to on).
Table 2-4 Locating the Failed RAM Location on Location on
ATARI NAMCO
RAM No. CPU PCB Video PCB CPU PCB Video PCB
| 0, 20, 40 | BF | 7H |
| 4,21, 41 | 7F | 7F |
| 22, 42 | Bu | 5H |
| 23, 43 | A) | SF |
| 2, 24, 44 | 8H | 6H |
| 3, 24, 45 | 7H | 6F |
| 26, 45 | 8K | 4H |
| 27,47 | 7K | 4F |
| 4, 28, 48 | SF | 7B |
| 29, 49 | 4F | 76 |
| 5, 30, 50 | 3E | 8B |
| 31,51 | 4E | 8c |
| 6 | WW | 7H |
| 7 | 7K | 8H |
| 8 | 7E | 4H |
Steering failure is indicated by failure of the numbers to the right of STEERING to properly increase or decrease. As you rotate the wheel clockwise, these numbers should increase; as you rotate the wheel counterclockwise, they should decrease. If the test fails, suspect the Coupler PCB.
Accelerator failure is indicated by failure of the numbers to the right of ACCEL to increase as you press down on the pedal. If no numbers appear, suspect a bad A-D converter on the CPU PCB ora mechanical problem on the foot pedal assembly. Troubleshoot using the information in Chapter 3, Section B, and the game schematics. Pole Position
Brake failure on the Sit-Down cabinet Is indicated by failure of the numbers to the right of BRAKE to change as you press down on the brake pedal. On the Upright cabinet, brake failure is indicated by anything other than 00 appearing to the right of BRAKE. If the test fails, suspect a bad switch, improper mechanical adjustment on the foot pedal assembly, orno ground on the brake edge-connector pin in the harness. Gear-shifter failure is indicated by failure of the words to the right of SH/FT to change from LO (shifter up) to H/ (shifter down) as you shift gears. If the test fails, suspect loose connector wires or a bad switch. Sound failure is indicated by the absence of any sound when the coin switches or gear shifterare activated. Suspect a loose harness or connector wire, the volume control turned off, the custom audio I/O chip, or the Regulator/Audio Ii board. Troubleshoot using the game schematics. To see self-test screen two, set the self-test switch to off and immediately back to on.
SELF-TEST SCREEN 2:
A white crosshatch pattern appears on the screen (see Figure 2-4). Use this pattern for convergence (see the raster-scan video display manual).
Figure 2-4 Self-Test Screen 2
Maintenance, Repair, and Parts
\ This chapter details maintenance and repair information and provides information you need to order parts for your game. Common hardware (screws, nuts, washers, bolts, etc.) has been deleted from most of the parts lists. However, a parts list for the hardware to mount the printed circuit boards (PCBs) to the cabinet has been included. The printed circuit board (PCB) parts lists are arranged in alphabetical order by component. Each component subsection is sorted by reference designator. Other parts lists are arranged alphanumerically by Atari part number. In these parts lists, all A-prefix numbers come first. Following these are numbers in sequence evaluated up to the hyphen, namely 00- through 99-, then 000598-through approximately 201000-. When ordering parts, please give the part number, part name, number of this manual, and serial number of your game. This will aid in filling your order rapidly and correctly. We hope the results will be less downtime and more profit from your game. Atari Customer Service numbers are listed on the inside front cover of this manual.
Maintenance, Repair, and Parts
A. Cabinet-Mounted Assemblies
Fluorescent Tube and Speaker See Figures 3-11 & 3-12 Pole Position
Manuals, Schematics, & Self-Test Label—- See parts list on next page
037332-01
029371-01 (Shield retainer)
Video Display See Figure 3-14
‘A037701-01 78-6900402, _ EMI Cage (Tape) See Figures 3-18
A039420-01 (Dashboard/decal) Steering-Wheel Control Assy. Gear-Shifter Control Assy. See Figure 3-5 See Figure 3-8
178034-024 Control Panel Assy. (T-Molding) See Figures 3-3 & 3-4
148001-001 oo grille) Vy
A038881-01 (Lock)
039119-02 (Access panel) 039376-01 (Access panel)
037742.01 (Bracket)
Game PCB Assy. See Figures 3-18, 3-19, & 3-20 & 323
A039459-01 (Main har. assy) A039499.01 (Main harn. assy) A039459-02
| Utility Panel | (Speaker) | Regulator/Audio I! |
| See Figure 3-15 | 039144-01 | PCB Assy. |
an (Speaker grille) See Figures Coin Door Assy.
| See Figures | ‘A039460-01 | 178048-001 |
| 316 & 3-17 | (Power harn. assy.) | (Caster) |
038870-01 Power Supply (Coin box enclosure— See Figure ah A037453-04 not shown) (Power cord) vais A037454-04
| {Goin box—nel shown) | ‘A039353-01 2 | (Power cord) |
(Cabinet assy) n037470-01 178034-025 (T-Molding) A039353-02 (On/off switch assy.) (Cabinet assy.) (00999201 7aag0t (<p Foot-Pedal Assy. A039353-03 (On/off switch cover) ( See Figure 3-9 (Cabinet assy)
Figure 3-1 Cabinet-Mounted Assemblies U.S.-Built Upright Cabinet lreland-Built Upright Cabinet
3-2 A039352-01 H A039352:02 H
Pole Position Maintenance, Repair, and Parts
Cabinet-Mounted Assemblies Upright Cabinet Parts List Assemblies and components in the following parts list are shown in Figure 3-1.
Part No. Description For U.S.-Built Upright Cabinet A037453.04 Strain-Relief Power Cord (U.S. and Canada) A037701-01 Electromagnetic Interference Cage (includes guides) A039353-01 Cabinet Assembly (includes glides and PCB retainers, but not access panel) A039459-01 Main Harness Assembly (for U.S. PCB) For lreland-Built Upright Cabinet A037454.04 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A039353-02 Cabinet Assembly (includes glides and PCB retainers, but not access panel) (for NAMCO PCB) A039353-03 Cabinet Assembly (includes glides and PCB retainers, but not access panel) (for Atari® PCB) A039459-02 Main Harness Assembly (for Atari® PCB) A039499-01 Main Harness Assembly (for NAMCO PCB) 037742-01 Printed Circuit Board Mounting Bracket 039119-02 Rear Access Panel 72-1620S #6-32 x 1.25-Inch Pan Head Machine Screw 75-016S #6 Flat Washer For U.S.-Built and Ireland-Built Cabinets A037470-01 Power On/Off Switch/Mounting Plate Assembly 4038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 A039420-01 Dashboard Housing and Decal Assembly A039460-01 Power Harness Assembly A039576-01 Coin Option Interconnect Assembly The following nine items are technical information supplements to this game: CO-218-01 Pole Position Supplement. (for NAMCO game PCB removal) SP-218 Pole Position Schematic Package (for Atari® game PCBs) or SP-219 Pole Position Schematic Package (for NAMCO game PCBs) ST-218-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for Atari® game PCBs) ST-219-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for NAMCO game PCBs) TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual! for 19-inch Wells-Gardner Color Raster-Scan Display (use with part no. 92-055) TM-218 Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Singie-Coated Adhesive Tape, #4-Inch Wide x ¥Inch Thick (48 inches required; used on top edge of video display shield, and on top edge of control panel) 78-6900404 Vinyl Foam Single-Coated Adhesive Tape, %4-Inch Wide x “%4-Inch Thick (48 inches required; used on top and bottom of attraction panel) 009992-01 On/Off Switch Cover 037332-01 Ventilation Grille 038091-01 Molded Coin Box (not shown) 038770-01 Metal Coin Box Enclosure (not shown) Acceptable substitute is part no. 038781-01 039144-01 Speaker Grille 039371-01 Video Display Shield Retainer 039376-01 Rear Access Panel (does not include lock) 039417-01 Video Display Shield with Graphics 148001-001 6- x 9-Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (located on front panel) 171034-xxx Over/Under Coin Door Assembly Acceptable substitute is part no. 171027-001. 178034-024 34-Inch Black Plastic T-Molding (/ocated on side panels) 178034-025 %,-Inch Black Plastic T-Molding (located on front panel) 178048-001 2-Inch Rigid Caster
Maintenance, Repair, and Parts Pole Position
A039465-02 (Main har. assy.) A039465-01 A039101-01 (Main harn, assy.) (Cabinet assy.) 039245-01 A039101-02 (Main harn, assy.) —= (Cabinet assy) Game PCB Assy. A039101-03 See Figures 3-18, 3-19 & 3-20 (Cabinet assy)
037990-01 (Vent. Grille)
- 148001013 (Speaker) 178034034 {T-Molding) A037701-01 EM cage) jee Figures 039144.01 3-18 & 3:23 (Grille) 038641-01 148001-001 (Vent. grille) (Speaker)
A038881.01 (Lock) | 178034-024 (T-Molding)
Utility Panel See Figure 3-15
Regulator/Audio Il PCB Assy. See Figures 3-21 & 3-22 \f Power Supply Assy. serine 1 See Figure 3-24 A039246-01 (Power harn. assy.) A037470-01 A037453-03. (On/off switch assy) (Power cord) 009992-01 A037454-03 (Onioff switch cover) (Power cord)
Figure 3-2 Cabinet-Mounted Assemblies U.S.-Built SitDown Cabinet A039100-01 F Ireland-Built Sit-Down Cabinet A039100-02 F
3-4
Pole Position Maintenance, Repair, and Parts
Manuals, Schematics, & Self-Test Label— See parts list on next page
039155-01 —_——— (Metal attraction panel) Gear-Shifter Control Assy. See Figure 3-8
a Video Display See Figure 3-14 Steering-Wheel Control! Assy. See Figure 3-5 037086-01 (Front window retainer)
030141.01 (Front window) (Tape)
039148-01 Control Panel Assy. (Display shield/graphics) See Figures 3-3 & 3-4
a Coin Door Assy. See Figures 3-16 & 3-17
038870-01 (Coin box exciosure) Foot-Pedal Assy. © > See Figure 3-9
178023-001 a (Caster)
(Glide)
Figure 3-2 Cabinet-Mounted Assemblies, continued U.S.-Built Sit-Down Cabinet A039100-01 F lreland-Built Sit-Down Cabinet A039100-02 F
Maintenance, Repair, and Parts Pole Position Cabinet-Mounted Assemblies Sit-Down Cabinet Parts List Assemblies and components in the following parts list are shown in Figure 3-2. Part No. Description For U.S.-Built Cabinet A037453-03 Strain-Relief Power Cord (U.S. and Canada) A037701-01 Electromagnetic Interference (EMI) Cage (includes guides) A039101-01 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039465-01 Main Harness Assembly For Ireland-Built Cabinet A037454-03 Strain-Relief Power Cord (Austria, Belgium, Chile, Denmark, Finland, France, Germany, Greece, Indonesia, Italy, Netherlands, Norway, Spain, Sweden, and Uruguay) A039101-02 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039101.03 Cabinet Assembly (includes glides and PCB retainers, but not the rear access panel) A039245-01 Main Harness Assembly (for NAMCO PCBs) For U.S.-Built and lreland-Built Cabinets A039246-01 Power Harness Assembly A039465-02 Main Harness Assembly (for Atari® PCBs) A037470-01 Power On/Off Switch/Mounting Plate Assembly A038881-01 Lock Assembly (for rear access panel) Acceptable substitute is part no. A038881-03 107001-001 Flat Black Paint The following nine items are technical information supplements to this game: CO-218-01 Pole Position Supplement (for NAMCO game PCB removal) SP-218 Poie Position Schematic Package (for Atari® game PCBs) or SP-219 Pole Position Schematic Package (for NAMCO game PCBs) ST-218-01 Pole Position Label with Self-Test Procedure and Option Switch Settings (for Atari® PCBs) or ST-219-01 Pole Position Label with Self-Test Procedure and Option Switch Setting (for NAMCO PCBs) TM-160 Service Manual for 19-Inch Electrohome Color Raster-Scan Display (use with part no. 92-049) TM-201 Service Manual for 19-Inch Weils-Gardner Color Raster-Scan Display (use with part no. 92-055) TM-218 Pole Position Operation, Maintenance, and Service Manual TM-220 Service Manual for 19-Inch Matsushita Color Raster-Scan Display (use with part no. 139003-1004) 72-1620S #6-32 x 1.25-Inch Pan Head Machine Screw 72-5524 #%-20 x 1.50-Inch Hex Head Machine Screw 75-016S #6 Flat Washer 75-045S %-\nch Split-Lock Washer 78-3201 Adjustable Glide 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, %-Inch Wide x Inch Thick (48 inches required; used on control panel) 78-6900804 Vinyl Foam Single-Coated Adhesive Tape, ¥2-Inch Wide x %Inch Thick (48 inches required; used in top slot of video display cleat, and on top and bottom of front window) 002728-01 Control-Panel Mounting Bracket 009992-01 On/Off Switch Cover 036851-01 Top Panel Hinge 037086-01 Front Window Retainer 037742.01 Printed Circuit Board Mounting Bracket 037990-01 Ventilation Grill (on rear access panel) 038091-01 Molded Coin Box (not shown) 038641-01 Ventilation Grille (on rear access panel) 038870-01 Metal Coin Box Enclosure Acceptable substitute is part no. 038781-01 039141-01 Front Window 039144-01 Speaker Grille (located behind seat) 039145-01 Speaker Grille (located under control panel) 039148-01 Video Display Shield with Graphics 039155-01 Metal Attraction Panel with Graphics 148001-001 6- x 9-Inch Oval, 4-Ohm, 15 W Unshielded High-Fidelity Speaker (not shown—located behind seat) 148001-013 6- x 9-Inch Oval, 4-Ohm, 15 W Shielded High-Fidelity Speaker (located under contro! panel) 171034-xxx Over/Under Coin Door Assembly Acceptable substitute is part no. 171027-001 176015-110 #10 x %Inch Cross-Recessed, Pan-Head Tapping Screw (not shown—for mounting speakers/grilles to seat back) 178034-024 %-Inch Black Plastic T-Molding 178034-034 1-Inch Black Plastic T-Molding (located on seat back) 178023-001 4-Inch Rigid Caster 3-6
Pole Position
B. Player Controls
atid the Control Panel: Unlock and open the rear access panel (see Figure 3-3). Reach through the opening to the top of the control panei.
- Remove the four wing nuts and washers that secure the control panel to the Upright cabinet. Two wing nuts and washers secure the contro! panel to the Sit: Down cabinet.
- Guide or pull the control panel forward to its resting Position. The steering wheel and gear shifter are now accessible for maintenance or repair (see Figure 3-4). Make sure the foam tape is in good condition. This tape is on the control panei of the Upright cabinet, and on the display shield for the Sit-Down cabinet. 4, Reassemble in reverse order.
Figure 3-3 Controi Panel
Maintenance, Repair, and Parts Pole Position
72-JB3814S “2 Gorew) Players may receive an electrical shock if this ; control panel is not properly grounded! After ; servicing any parts on the panel, make sure that the ground wire is firmly attached to the metal tab on the inside of the contro| panel. 75002004. 1 (Washer)
A000608-09 GearShifter Control Assy. See Figure 3-6
(Spacer)
> / BB avsoss101 (Control panel/decal) 039373-01 (Contro! pane!) “ee |?) (Decal) ‘03910801 (Contro} panel/decal)
(Decal) 039143-01 (Control panel) 03915304 03913201 (Spacer) 6\--— \
75-5512B (Carriage bol) NY 75-5524B (Carriage bolt) \ A039229-01 ‘Steering: Wheel Contro! Assy. Assemblies A039107-01 and See Figure 3-5 A039412-01 are used with Atari game PCBs; Assemblies A039107-02 and A039412-02 are used with Namco game PCBs. Figure 3-4 Control Panel Assembly Upright Cabinet A039412-01 & -02 A Sit-Down Cabinet A039107-01 &-02 B
Pole Position Maintenance, Repair, and Parts
Control Panel Assembly Parts List
Assemblies and components in the following parts list are shown in Figure 3-4.
Part No. Description
Upright Cabinet A039411-01 Control Panel with Decal (consists of control panel 039373-01 and decal 039409-04) 75-5112B #%-20 x .75-Inch Black Carriage Bolt 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥-Inch Wide x %-Inch Thick (96 inches required) Sit-Down Cabinet A039108-01 Control Panel with Decal (consists of control pane! 039143-01 and decal 039153-04) 75-035S Y%-Inch Wide Flat Washer 75-5512B #%-20 x 75-Inch Black Carriage Bolt 75-5524B #%-20 x 1.50-Inch Carriage Bolt 039132-01 Control Panel Spacer Upright and Sit-Down Cabinets A039229-01 Steering-Whee! Control Assembly (Namco games use part no. A039229-02) A000608-09 Gear-Shifter Control Assembly 72-JB3814S #8-16 x .87-Inch Screw 005255-04 Shifter Bezel 039154-01 Shifter Spacer 175002-004 #10 Flat Washer 177010-244 #¥%4-20 Hex Locknut
3-9
178099-003 Maintenance, Repair, and Parts Pole Position
039243-01 (Steering wheel) (Label)
039230-01 (Steering cap)
039231-01 (Shaft)
175003-002 (Nylon washer) 178012-002 039234-01 (Retaining ring) (Steering frame)
72-HB3606S (Hex screw)», Oy
A035220-02 178100-001 (Flange bearing) (Coupler PCB assy) 2 178007-001 (Bearing assy.) wa 175002-001 EB (Washer) 175003-002 (Nylon washer) 178012-001 039233-01 (Retaining ring) (Encoder shat)», 178101-002 ee (Gear)
175002-002 ‘(Heavy washer) + 75-040 ‘Space! aN Z pacer) (Washer)
72-8008 (Screw)
= NYOGEL 779 A = SIN-ONE OIL 035938-01 (Encoding whee!)
(Split-ock washes 72-B408
See text for lubrication information.
Figure 3-5 Steering-Wheel Control Assembly A039229-:01 D
3-10
Pole Position Maintenance, Repair, and Parts
Steering-Wheel Control Assembly Parts List
Assemblies and components listed in the following parts list are shown in Figure 3-5.
Part No. Description
A035220-02 Coupler Printed-Circuit Board Assembly (includes Radial Optical Coupler) 72-8008 #10-32 x 0.50-Inch Steel Socket-Head Cap Screw 72-8012 #10-32 x 0.75-Inch Steel Socket-Head Cap Screw 72-8408 #4-40 x 0.50-Inch Steel Socket-Head Cap Screw 72-HB3606S #6-32 x 0.38-Inch Zinc-Plated Steel Hex Washer-Head Screw 75-018S #8 Flat Washer 75-040S #10 Split-Lock Washer 75-044S #4 Split-Lock Washer 75-07014 #4 Flat Washer 79-58356 4-Position Connector with Locking Ramp (located on the Coupler PCB Assembly) 030369-01 Radial Optical Coupler (located on the Coupler PCB Assembly) 035221-01 1002, +5%, %4W Resistor (located on the Coupler PCB Assembly) 039230-01 Steering Cap 039231-01 Steering Shaft 039232-01 Spacer 040264-01 Encoder Shaft Acceptable substitute is part no. 039233-01 039234-01 Steering Frame 039243-01 Steering Cap Label 035938-01 Encoding Wheel 107013-001 3-in-One® Oil 175002-001 Flat Washer 175002-002 #10 Heavy Flat Washer 175009-170 Nylon Flat Washer 178012-001 Retaining Ring for 0.75-Inch Shaft 178012-003 Retaining Ring for 0.25-Inch Shaft 178027-001 Nyogel 779 Lubricant 178097-001 Bearing for 0.25-Inch Shaft 178099-003 Steering Wheel 178100-001 Bearing Flange for 0.75-Inch Shaft 178101-001 24 Diametral Pitch x 20° Pressure Angle x 2.500 Pitch Diameter Spur Gear 178101-002 24 Diametral Pitch x 20° Pressure Angle x 0.583 Pitch Diameter Spur Gear 178118-001 Sleeve Bearing
Maintenance, Repair, and Parts
Before you remove or repair any player control, turn the game off.
Removing the Coupler PCB, Encoding Wheel, and Steering Wheel:
- Open the control panel (see Figure 3-3).
- To remove the steering-wheel control assembly, disconnect the green ground wire from the grounding hardware. Remove the hardware which secures the steering-wheel contro! assembly to the control panel (see Figure 3-4). Pole Position
Unplug the harness connector on the Coupler PCB. To remove the Coupler PCB, remove the hardware securing the PCB to the steering frame. To remove the encoding-wheel assembly, hold the shaft of the encoding wheel in a fixed position with a wrench. Usean Allen wrench to remove the cap screw, encoding wheel, washers, spacer, and bearing. To remove the encoder shaft, pry off the retaining ring. To remove the steering wheel, hold the steering wheel shaft in a fixed position. Remove the cap screw, washers, and gear. Pry off the retaining ring and remove the heavy washer. Reassemble in reverse order.
OPEN-END WRENCH ALLEN WRENCH.
ENCODING WHEEL
Figure 3-6 Steering-Wheel! Control Screw Adjustment
Pole Position
Lubricating the Steering-Wheel Control:
Periodic maintenance of the steering-wheel control assembly must include the folowing procedures: 1. Check that the #4-40 x ¥2-inch socket-head cap screw (part no. 72-8408) on the encoder shaft is secure (see Figure 3-6). \f the screw needs tightening, hold the encoder shaft (part no. 039233-01) with a %,-inch openend wrench while tightening the screw with a %,-inch Allen wrench. Check that the #10-32 x ¥2-inch socket-head cap screw (part no. 72-8008) on the steering-wheel shaft is tight (see Figure 3-5). if the screw needs tightening, hold the steering wheei still while using a 5%-inch Allen wrench to tighten the screw. Check, and if necessary, lubricate the encoder shaft (part no. 039233-01) and the two flat nylon washers (part no. 175003-002) as shown in Figure 3-5. Use ONLY the recommended lubricant, Nyogel 779 (part no. 178027-001). Nyogel 779 is a damping grease and will aid in the smooth operation of the control. Make sure a HEAVY film of this lubricant is applied to the encoder shaft and both surfaces of the nylon washers. Check for a grinding feeling caused by inadequate !ubrication or by the gears being too close together. To correct this condition, lubricate with Nyogel 779, and/or loosen the locknut on the bearing assembly Maintenance, Repair, and Parts
(part no. 178097-001) and move the bearing away from the main steering shaft toward the coupler PCB assembly. This movement may be very small, but it can make a difference. Check, and if necessary, lubricate the bronze flange bearings (part no. 178100-001) in the steering frame (part no. 039234-01), using a few drops of a light machine oil, such as 3-in-One oi! (part no. 107013-001) (see Figure 3-5). The steering-wheel control assembly should be positioned as follows (see Figure 3-7): a. Open the control panel. b. Disconnect the green ground wire from the grounding hardware. Remove the four carriage bolts that secure the steering-wheel control assembly to the control panel. c. Rotate the steering-wheel control assembly 90° so that the encoding wheel assembly and the encoder shaft are on the bottom (nearest the floor). All new Pole Position games will be assembled in this manner. d. Reinsert the four carriage bolts that secure the steering-wheel control assembly to the control panel. Reconnect the green ground wire.
STEERING-WHEEL CONTROL aa COUPLER PCB GEAR-SHIFTER CONTROL
CONTROL PANEL
Figure 3-7 Steering-Wheel Control! Orientation
3413
Maintenance, Repair, and Parts Pole Position
005255-04 OS (Bezel) N\
ye See text for lubrication information.
000610-02 (Shifter handle)
039705-01 (Spring)
76-11375S, (Bali bearing) 000609-02 (Shift housing)
72-1412 (crew)
(Switch) (Shift detent)
NN (Hex nut) 035301-02 (Actuator pin)
Figure 3-8 Gear-Shifter Control Assembly A000608-09 AB
3-14
Pole Position Maintenance, Repair, and Parts
- To remove the switch, remove the two screws and locknuts that secure the switch to the housing. Be careful not to lose the small actuator pin that sits above the switch actuator.
- Reassemble in reverse order. Before you remove or repair any player control, turn the game off.
Removing the Gear-Shifter Control Assembly:
- Open the control panel (see Figure 3-3).
- To remove the gear-shifter contro! assembly (see Lubricating the Gear-Shifter Control: Figure 3-4), disconnect the plug-in connectors from the switch. Remove the hardware that secures the To lubricate the gear-shifter control assembly, open the control panel (see Figure 3-3) and remove the gear-shifter gear-shifter control assembly to the control panel. control assembly using the procedure above. Apply a light-
- To open the gear-shifter assembly, remove the six duty lubricant (such as Nyogel 779) every six months to the screws that secure the two halves of the housing (see spherical part of the handle and the detent. Figure 3-8).
Gear-Shifter Control Assembly Parts List
Assemblies and components listed in the following parts list are shown in Figure 3-8.
Part No. Description 000610-02 Gear-Shifter Handle 65021A Single-Pole Single-Throw Low-Force Miniature Switch 72-JB3606 #6 x 0.38-Inch Steel Plastite Screw Acceptable substitutes are part nos. 72-JB3608, 72-JA4608, and 72-JB16068 72-14128 #4-40 x 0.75-Inch Cross-Recessed Pan-Head Steel Machine Screw
76-11375S % Inch Ball Bearing 75-9448 #4-40 Self-Locking Polymer Hex Nut 78-3002003 Spring 000609-02 Gear-Shifter Housing (two required) 005255-04 Shifter Bezel 035792-01 Shift Detent 035301-02 Actuator Pin 178027-001 Nyogel 779 Lubricant (not shown)
3-15
Maintenance, Repalr, and Parts Pole Position
an 039241-01 (Safety tread) ‘See text for lubrication information.
039240-01 039236-01 (Foot pedal—accelerator) (Pivot pin)
040028-01 (Compression spring)
178012-004, 03924201 (Retaining ring) (Cable)
(Pulley)
039704-01 (Extension spring) SS (co screw) Cap screw of pulley must be in this position when pedal is fully open (at rest). 039703-01 (Cable spring) 039239-01 (Base plate) renpans* 19-9026 (Screw) (Potentiometer) = 160023-001* (witch)
*For Sit-Down cabinet (dual foot-pedal assembly)
**For Upright cabinet (single foot-pedal assembly)
'039142-01° . oe Mounting plate) 039379-01** (Mounting plate)
4 = NYOGEL 779 &d = WD-40 75-040S** (Washer)
Figure 3-9 Foot-Pedal Control Assembly
3-16
Pole Position Maintenance, Repair, and Parts
Foot-Pedal Control Assembly Upright A039413-01 B Sit-Down A039109-01 C Parts List
Assemblies and components in the following parts list are shown in Figure 3-9.
Part No. Description Sit Down Cabinet A039247-01 Dual Foot-Pedal Control Harness Assembly 72-HB3410S #4-40 x .62-Inch Thread-Forming Hex Washer-Head Screw 75-010S #10 Tooth Internal Lock Washer 160023-001 SPDT Snap Switch with Actuator Upright Cabinet A039463-01 Single Foot-Pedal Control Pedal Harness Assembly 75-035S %-Inch Flat Washer 75-040S #10 Tooth Internal Lock Washer 75-5520B #%-20 x 1.25-Inch Black Carriage Bolt (not shown) 75-915S #%-20 Hex Nut 039379-01 Single Foot-Pedal Control Mounting Plate Upright and Sit-Down Cabinets 19-9026 5 kQ Potentiometer 72-8606 #6-32 x .38-Inch Hex Socket-Head Cap Screw 75-9415 #10-24 Hex Locknut
| 040028-01 | Compression Spring | (for pedal) |
039236-01 Pivot Pin 039238-01 Pulley 039239-01 Foot-Pedal Control Base Plate 039240-01 Foot Pedal 039241-01 Safety Tread 039242-01 Cable 107012-001 Dry Teflon Spray Lubricant (not shown) 178012-004 External Retaining Ring for ¥-Inch Diameter Shaft
| 178026-005 | Extension Spring | (for cable) |
| 178026-006 | Extension Spring | (for pedal) |
3-17
Maintenance, Repair, and Parts
Before you remove or repair any player control, turn the game off.
Removing the Foot-Pedal Control Assembly:
- Unlock and open the rear access panel. Reach through the opening to the top of the foot-pedal control.
- Remove the two locknuts located on the top two footpedal mounting screws.
- From the front of the Upright cabinet or in the player area of the Sit-Down cabinet, remove the foot-pedal mounting screws and lift out the foot-pedal control assembly. Pole Position
Foot-Pedal Control Maintenance:
Periodic maintenance of the foot-pedal controls must include the following procedures:
- The only maintenance required on this newly designed foot-pedal contro! is lubrication every four months (see Figure 3-9). Lubricate the pivot pin and surround-
- Place the foot-pedal control assembly upside down on a work surface in front of you with the pedal in a fully open position and the hinged end away from you.
CABLE
- Wrap the cable one quarter-turn around the pulley and bring it out through the notch toward the cap screw.
- Thread the cable up through the opening in the base plate.
LARGER EYELET
- Rotate the pulley until the cap screw points straight up.
PULLEY
- Hook the larger eyelet of the cable to the foot-pedal bracket.
BRACKET
Figure 3-10 Foot-Pedal Pulley Cable Rewinding
3-18
Pole Position Maintenance, Repair, and Parts
ing area, the spring cable, and pulley with dry teflon 3. If the pulley cable needs rewinding, adjust as shown in spray. If needed, apply a light-duty lubricant like WD-40 to the potentiometer shaft only.
- If your accelerator pedal fails to return to its uppermost position, check for the foliowing conditions: Figure 3-10.
| a. | Inadequate lubrication of the peda! assembly. Lu- | Ifitis ne |
: ecessary to disassemble the foot-pedal bricate as necessary. control assembly and remove the pulley cable
| b. | A broken extension spring (part no. 039704-01). | (part no. 038242-01), MAKE SURE the cable is |
Replace if necessary. wound as illustrated in Figure 310. BE . : i fray the cable in the
| c. | A broken or inadequately lubricated compression | CAREFUL not to cut or |
spring (part no. 000592-01), Replace and/or lubri- feet badet eosembly Hustbe renewed oe bis cate II necessary. . . game Cabinet in order to wrap the cable cor-
| d. | Inadequate lubrication of the potentiometer shaft | rectly. |
(part no. 19-9026). Lubricate as necessary with a light-duty lubricant, such as WD-40 (part no. 78-1701).
- Wrap the cable twice around the cap screw in a clockwise direction.
- Attach the smaller eyelet on the cable to the cable spring. NOTE: You may find it helpful to compress the base plate slightly and extend the cabie spring during this step,
- Bring the cable back through the notch and wrap it around the pulley ‘one and one-half times.
CABLE SPRING
SMALLER EYELET
Figure 3-10 Foot-Pedal Pulley Cable Rewinding, continued
3-19
Maintenance, Repair, and Parts
C. Fluorescent Tube and Speaker Replacement
Upright Cabinet
Removing the Tube and Speaker Board:
- From the back of the game, unlock and open the rear access panel. Unplug the tube and speaker's 5-pin harness connector (see Figure 3-11).
- From the front of the game, remove the three buttonhead screws and lock washers that secure the upper attraction-panel retainer to the cabinet. Loosen the screws and washers that secure the iower attractionpanel retainer to the cabinet.
- Remove the attraction glass. 4, Remove the lower retainer, Pole Position
Remove the two wood screws that secure the tube and speaker board to the cabinet. Slide this board out of the cabinet. After making necessary repairs or replacements, make sure that the tube and speaker board is pushed all the way back on the tube and speaker panel when you reinstall the board.
Replacing the Fluorescent Tube:
- Check that the green ground wire is securely attached to the large metal bracket and the baliast transformer on the wood panel. If the tube is not grounded, it may not start.
- Remove the cardboard locking tab at each end of the tube (see Figure 3-12). Slightly rotate the tube up or down and carefully remove it from the tube holder.
- Replace it with a new tube. Do not snap in the tube vigorously— you may break it, causing an implosion! Replace the locking tabs.
Replacing the Upper Speaker:
- Disconnect the two plug-in connectors on the speaker.
- Remove the screws that attach the speaker to the board (see Figure 3-12). Replace with a new speaker and reinstall the tube and speaker board.
Replacing the Lower Speaker: From the back of the game, unlock and open the rear access panel. Refer to upper speaker removal procedure in Figure 3-12).
78-6900402 (Tape) oseateo1——__ (Attraction glass! graphics)
039144-01 148001-001 (Speaker grille) é (Speaker) f
003053-01 (Retainer)
Figure 3-11 Fluorescent Tube and Speaker Board Removal
3-20
Pole Position Maintenance, Repair, and Parts
148001-013 70-304 99-11006 (Speaker) (Tube) (Tab)
179035-001 (Tube holder) e162 ‘A037457-01 | jar (G) (Screw) (Harness)
142028-001 (Transformer) 142028-002 (Transformer)
$9-11003. (Starter)
99-1109 (Socket) 037469-01 (Bracket)
Figure 3-12 Fluorescent Tube and Speaker Board Assembly U.S.-Built Upright Cabinet A039415-01 A lreland-Built Upright Cabinet A039415-02 A Parts List
Part No. Description
For U.S-Built Upright Cabinet 142028-001 60 Hz, 118 V, Ballast Transformer (used on A037458-01 assembly) For ireland-Built Upright Cabinet 142028-002 50 Hz, 118 V, Ballast Transformer (used on A037458-02 assembly) For U.S- and Ireland-Built Upright Cabinet A037457-01 Tube and Speaker Harness Assembly A037540-01 Ground Wire with Ring Lug 70-304 18-Inch, 15 W, Cool White Fluorescent Tube 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥-Inch Wide x %-Inch Thick 79-561816P. Spring-Connector Wire Nut for 16- to 18-Gauge Wires 99-11003 Fluorescent Tube Starter 99-11006 Fluorescent Tube Locking Tab (tab consists of two pieces) 99-11009 Starter Socket 003053-01 Upper and Lower Attraction Glass Retainer 037469-01 Steel Tube Bracket 039418-01 Attraction Glass with Graphics 003053-01 Upper and Lower Attraction Glass Retainer 039144-01 Speaker Grille 148001-013 6 x 9-Inch Oval, 4-Ohm, 6-Ounce, Shielded High-Fidelity Speaker 176015-112 #10 x %-Inch Pan Head Machine Screw 179035-001 2-Pin Fluorescent Tube Holder 179125-001 Grounding Clip (not shown)
*148001-001 6 x 9:Inch Oval, 4-Ohm, 6-Ounce, High-Fidelity Speaker—mounted to the cabinet near the coin door, behind speaker grille part no, 039144-01
3-21
Maintenance, Repair, and Parts
SitDown Cabinet
Replacing the Front Speakers:
- For the right speaker, unlock and open the rear access panel (see Figure 3-13). For the left speaker, open the control panel (see Figure 3-3).
- Unplug the two plug-in connectors.
- Remove the two screws that secure the speaker to the wood speaker panel. Replacing the Seat-Panel Speakers: 4.
5. Pole Position
“SS Remove the six wood screws that secure the seatback panel to the cabinet (see Figure 3-13). Lean the seat-back panel forward. Disconnect the two plug-in connectors on each speaker. Remove the seat-back panel from the player area of the cabinet. Remove the four screws that secure each speaker to the seat-back panel. Reassemble in reverse order.
Figure 3-13 Sit-Down Cabinet Speaker Removal
3-22
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
Maintenance, Repair, and Parts
D. Video Display
Removing the Video Display From the Upright Cabinet:
- From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-14).
- Remove the four sets of hardware that secure the video display to the wood display shelf.
- Open the control panel (see Figure 3-3).
- Remove the three wing nuts (located on the displayshield support) that secure the dashboard panel to the cabinet.
- From the front of the cabinet, lift off the dashboard panel.
- Remove the hardware that secures the display-shield retainer. Lift the display shield up and out of the cabinet.
- Remove any staples that may secure the bezel to the cabinet. Then, carefully remove the cardboard bezel.
- Carefully pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.
3-24 Pole Position
Removing the Video Display From the Sit-Down Cabinet:
- From the back of the cabinet, unlock and open the rear access panel. Unplug the 6-pin connector from the video chassis, the 2-pin 110-VAC connector, and disconnect the ground wire (see Figure 3-14).
- Remove the four sets of hardware that secure the video display to the wood display shelf.
- Open the contro! panel (see Figure 3-3).
- Move to the player area of ihe cabinet. Grasp the bottom edge of the video display shield and slide the shield out and down. Make sure the foam tape on the bottom of the shield is in good condition.
- Remove any staples that may secure the bezel to the cabinet. Then, carefully grasp the bottom edge of the cardboard bezel and remove it from the cabinet.
- Pull the display out through the front of the cabinet. Place the display in a protected location. After servicing the display, reinstall in reverse order.
Pole Position Maintenance, Repair, and Parts
03914801 039371-01 (Gree) be dahl Bezel carat 039417-01 Gezel (Shield) 039407.01 ! (Bezel) 92.049 (Electrohome display)
¢ 039363-02 i ul i 7ee900402 a / (Tape) 039123-02 $ 78-6900804 (Shelf : (Tape) A
Figure 3-14 Video Display Upright and Sit-Down Cabinets Parts List
Part No. Description For Upright Cabinet 039363-02 Display Shelf 039371-01 Retainer 039407-01 Display Bezel 039417-01 Display Shield 78-6900402 Vinyl Foam Single-Coated Adhesive Tape, ¥4-Inch Wide x Inch Thick For Sit-Down Cabinet 039123-02 Display Shelf 03914801 Display Shield 039149.01 lay Bezel 78-6900804 Vinyl Foam Single-Coated Adhesive Tape, ¥2-Inch Wide x j-Inch Thick For Upright and Sit-Down Cabinets 92-049 19-Inch Electrohome Color Raster-Scan Display Alternate display is part no. 139003-1004—19-Inch Matsushita Color Raster-Scan Display
Maintenance, Repair, and Parts Pole Position
sis. The utility panel is located inside the upper coin door. E. Utility Panel This panel includes the volume controls), self-test switch, auxiliary coin switch, and the coin counter(s) (see Figure 3-1). The auxiliary coin switch is used to credit the game without tripping the coin counter. Before removing or repairing the utility panel, turn the game off. Players may receive an electrical shock if the NOTE Only Ireland-Built cabinets have two coin counters. If using both coin counters, the pad utility panel is not properly grounded! After servicing any parts on the panel, make sure that the ground wire is firmly attached to the CPI metal screw on the back of the coin counter. Be ae tet andl 12-00 tha GP ,ROe must be split.
03025401 (Dual component 039457-01 haynes) (utility panel— U.S.-Built Upright only) oon era 039295-01 2 Be (Utility pane!) ~ hamess)
(Coin counter) \ y A039248-01 .\ (Vol. control 479070-001 (Vol. control harness) (Vol. contro! knob)
(Vol. control)
176018-002 (Screw) ,, > 75-916S oe bali uid (Hex nut) 75-9810W0 62.041 (Stamped nut) (Auxiliary coin switeh)
SWITCH NOT USED
Figure 3-15 Utility Panel Assembly A039391-xx F
3-26
Pole Position Maintenance, Repair, and Parts
Utility Panel Assembly Parts List
Part No. Description For U.S.-Built Upright Cabinet 039457-01 Utility Panel (for 2 volume controls) For Ireland-Built Upright Cabinet 039295-01 Utility Panel (for 4 volume controls) For U.S.- and lreland-Built Upright Cabinet A039254-01 Dual Component Harness Assembly For U.S.- and Ireland-Built Sit-Down Cabinet A038004-01 Utility Panel Harness Assembly A039248-01 Volume Control Harness Assembly 039295-01 Utility Panel (for 4 volume controls) For U.S.- and Ireland-Built Upright and Sit-Down Cabinets A002465-01 6 V Coin Counter 19-9032 50 Q, 12.5 W Volume Control 62-041 SPST Momentary-Contact Pushbutton Auxiliary Coin Switch with Black Cap 69-001 DPDT Self-Test Switch 176018-002 #6-32 x ¥2-Inch Thread-Forming Screw 75-916S #6-32 Steel Machine Hex Nut 75-9910W0 #15/32-32 Stamped Nut 178070-001 Volume Control Knob
3-27
Maintenance, Repair, and Parts
FE. Coin Doors
179047-001 (Lamp Base)
99-15056 (Screw for Bezel)
99-15025 (Coin Inlet) F
99-15055 (Retaining Screw) Pole Position
170000-001 (Lamp)
99-15023 (Base Plate)
99-15026 (Coin Inlet)
2 9915054 (Pivot for Lever)
75-9148 | oat YL (Hex Nut! (HeKNe) T6056 bx SN (Lock Wash.) SS
99-15075 (Sw. Adjuster)
99-15029 (Bracket)
3-28 [<—(Coin Return Box)
SSerew for Bezel)
(Switch)
7214148 (Screw)
Figure 3-16 Vertically Mounted Coin Door 171034-xxx
Maintenance, Repair, and Parts Pole Position
99-15038 (Bezel for Button) A037542-01 (Harness—not shown)
99-15001 thru 99-15011 (Return Button)
99-15071 (Clamp)
(Lower Door) (Spring for Button)
9915039 (Bezel for Cover}
99-15036 99-15073 (Upper Door)
99-15063 (Screw)
99-15067 sy.) (Lock As:
(Doors and Frame) (Coin Box) 038091-01
99-15072 (Door Frame)
171034-011 — German 1 MIS M Coin Door 171034015 — French 2 Fi F Coin Door 171034009 — German 2 Mi1 M Coin Door 171034.010 — German 2 M/5 M Coin Door 171034-006 — U.K. 20 P/50 P Coin Door 171034-901 — U.S. 25e/25¢ Coin Door 171034-003 — Canadlan 25¢/25¢ Coin Door 171034-005 — U.K, 10 P/50 P Coin Door
continued 3-16 Vertically Mounted Coin Door, Figure 171034-xxx
3-29
Maintenance, Repair, and Parts Pole Position
Vertically Mounted Coin Door Parts List
Part No. Description A037542-01 Harness Assembly 7214148 #4-40 x %Inch Cross-Recessed Pan-Head Steel Machine Screw 75-056 #6 Internal-Tooth Zinc-Plated Steel Lock Washer 75-9145 #4-40 Steel Machine Hex Nut 75-3414S #4-40 x %-Inch 82° Cross-Recessed Flat-Head Steel Machine Screw 99-15001 Coin Return Button with U.S. 25¢ Price Plate 99-15002 Coin Return Button with U.S. $1 Price Plate 99-15003 Coin Return Button with German 1 DM Price Plate 99-15004 Coin Return Button with German 2 DM Price Plate 99-15005 Coin Return Button with German 5 DM Price Plate 99-15006 Coin Return Button with Belgian 5 Fr Price Piate 99-15007 Coin Return Button with French 1 Fr Price Plate 99-15008, Coin Return Button with Japanese 100 Yen Price Plate 99-15009 Coin Retum Button with British 10 Pence Price Plate 99-15010 Coin Return Button with Australian 20¢ Price Plate 99-15011 Coin Return Button with Italian 100 Lire Price Plate 99-15023 Base Plate 99-15025 Left Half of Coin Inlet 99-15026 Right Half of Coin Inlet 99-15027 Side Plate of Coin Return Box 99-15028 Base Plate of Coin Return Box 99-15029 Switch Bracket 99-15036 Metal Coin Return Cover 99-15038 Bezel for Coin Return Button 99-15039 Metal Bezel for Coin Return Cover 99-5040 Coin Return Lever 99-15042 Coin Switch for U.S, 25¢ 99-15052 Spring for Coin Return Button 99-15054 Pivot for Coin Return Lever 99-15055, Retaining Screw 99-15056 #4-40 x %.-Inch Cross-Recessed Pan-Head Steel Machine Screw 99-15060 Switch Cover 99-15063 ‘Screw for Hinge 99-15066, Screw for Clamp 99-15067 Lock Assembly 99-15070 Doors and Frame 99-15071 Clamp for Frame 99-15072 Door Frame 99-15073 Upper Door 99-15074 Lower Door 99-15075 Switch Adjuster 038091-01 Coin Box (Not included in assembly) Acceptable substitute is part number A037491-01 170000-001 6.3 V Miniature Wedge-Base Incandescent Lamp 171006-035 Metal Coin Mechanism 179047-001 Lamp Base
3-30
Pole Position Maintenance, Repair, and Parts
99-10140 (Panel assy.)
75-948S (Locknut) 99-10116 (Lever)
99-10151 (Left coin inlet),
99-1080 (Lamp socket),
70-11-47 (Lamp)
/ (Bar retainer) 9406S 72: (Screw) 99-10147 (Harness)
99-10154 (Bracket assy.)
99-10042 thru 99-10045 (Coin switch assy.) 99-10153 WD (Coin return box) Sq to ( | 65-441 _ ee (Coin switch) =o — 99-10075 thru 99-10078 (Switch wire) 99-1008 (Retainer) 99-10150 (Switch cover)
75-1412S (Screw)
Figure 3-17 American-Made Coin Door 171027-001 A
3-31
Maintenance, Repair, and Parts aD Pole Position
99-10148 (Lock)
72-HA1404C (Screw) 99-10142 (Button housing)
99-10139 (Coin door —>| 99-10134 (Cover)
99-10118 (Button)
99-10115 (Spring)
S 4 99-10141 “cm aS | § > (Coin return cover)
® 99-10117 (Coin return door)
99-1014 L |x—-(Channel clip)
- Se 72-JA1405B (Screw)
99-10149 (Service door)
038091.01 (Coin box)
99-10143 (Frame)
Figure 3-17 American-Made Coin Door, continued 171027-001 A
3-32
Pole Position Maintenance, Repair, and Parts
American-Made Coin Door Parts List Assemblies and components in the following parts list are shown in Figure 3-17.
Part No. Description A039576-01 Coin Option Interconnect Assembly (not shown) 171006-035 Meta! Coin Mechanism for U.S. $.25 65-4410 Coin Switch 70-11-47 Miniature Bayonet Lamp 72-9406S #4-40 x %-Inch Truss-Head Screw 72-HA1404C, #4-40 x %4-Inch Pan-Head Screw 72-JA1405B #4-40 x .31-Inch Pan-Head Screw 75-1412S #4-40 x %4-Inch Pan-Head Screw 75-994S #4-40 Lock Nut 99-10008 Retainer 99-10042 Coin Switch Assembly for Belgium 5 Fr and U.S. $.25 99-10043 Coin Switch Assembly for German 1 DM, Japanese 100 Yen, Swiss 1 Fr 99-10044 Coin Switch Assembly for German 2 DM, Italian 100 L, U.S. $1.00 99-10045 Coin Switch Assembly for Australian $.20, German 5 DM, British 10 P 99-10068 Coin Return Chute 99-10075 Switch wire included in coin switch assembly) 99-10076 Switch wire (included in coin switch assembly) 99-10077 Switch wire (included in coin switch assembly) 99-10078 Switch wire (included in coin switch assembly) 99-10080 Lamp socket 99-10081 Key holder 99-10096 Fastener 99-10104 Bar retainer 99-10105 Bar 99-10115 Spring 99-10116 Piastic Coin Return Lever 99-10117 Steel Coin Return Door 99-10118 Amber Coin Return Button 99-10119 Amber Coin Button for U.S. $.25 99-10134 Coin Button Cover 99-10139 Coin Door 99-10140 Coin Door Inner-Panel Assembly . 99-10141 Diecast Coin Return Cover 99-10142 Diecast Button Housing 99-10143 Coin Door Frame 99-10144 Coin Door Channel Clip 99-10145, Offset Cam (includes 99-10148—Lock) 99-10146 Coin Inlet Chute Assembly 99-10147 American-Made Coin Door Harness 99-10149 Service Door 99-10150 Switch Cover 99-10151 Left Coin Inlet 99-10152 Right Coin Inlet 99-10153 Coin Return Box 99-10154 Bracket Assembly
3-33
Maintenance, Repair, and Parts Pole Position
G. Printed-Circuit Boards
039378-03 (Retainer) A037767-01 (EMI Shield PCB)
178015-110 Shield PCB 037873-01 (Screw) (Spacer)
A039431-01 (End PCB)
034536-03 (Screw) (Foam pad) A037701-01 (EMI cage) LG (Screw)
178044-242 A038187-21 A039185-21 (Pole Position Video PCB) (Grommet) (Pole Position CPU PCB) : " 175009-221 Washer) NOTE 178045-442 The FCC requires that the game (Fastener) PCB be housed in the EMI cage with the Shield PCB attached.
A035435-01 176015-110 A035435-05, (Screw) (Regulator! 175004-708 Audio i PCB) (Washer)
*Steps 1, 10, and 11 are not illustrated.
Figure 3-18 Removing the Printed-Circuit Boards
3:34
Pole Position
Before you remove or repair any printed-circuit board, turn the game off. Maintenance, Repalr, and Parts
- Unplug the End PCB that connects the two game PCBs.
- Determine which PCB you need to repair or replace, and remove the two pan-head screws that connect that PCB to the spacers. Replace or repair as required, and reinstall the PCBs. (Make sure the foam vibration damper is placed between the game PCBs.) Removing the Printed-Circuit Boards: Removing a Regulator! Audio II PCB: Removing the Game PCBs from the EMI Cage 8. To remove a Regulator/Audio !| PCB, disconnect the
- Open the rear access panel. small harness connectors on the board.
- The game printed-circuit boards (PCBs) are located in- 9 Remove the hardware that secures the Regulator/Audio || PCB to the cabinet, and carefully lift the board from the retainer. Do not twist the board, as this may loosen connections or components. Replace or repair as required and reinstall the PCB. side the electromagnetic interference (EMI) cage (see Figure 3-18). The EMI cage is located on the cabinet wall of the Upright game and on the inside of the rear access panel of the Sit-Down game. Unpiug the two harness edge-connectors from the EMI Shield PCB.
- To remove the game PCBs, pull the eight nylon snap-in fasteners on the EMI Shield PCB to the unlocked position. Carefully slide the Shield PCB and attached PCBs straight out of their guides. Be careful not to twist the boards, as this may loosen connections or components, Removing the EMI Shield PCB from the Game PCBs
- Remove the two pan-head screws that connect the EMI Shield PCB to the spacers.
- Push the EMI Shield PCB off the game PCBs by applying pressure with your thumbs to the edge connec-
Make sure that the connectors on each PCB are properly plugged in. Note that they are keyed to fit only one way. If they do not slip on easily, do not force them. A reversed connector may damage your game and void the warranty.
- Close and lock the rear access panel. tors. 11, Important: Perform the self-test.
Printed-Circuit Board Mounting Hardware Parts List Assemblies and components in the following parts list are shown in Figure 3-18.
Part No. Description
U.S-Built Upright and Sit-Down Cabinets A037701-01 Electromagnetic Interference (EMI) Cage (includes guides) 721404F #4-40 x Va-Inch Cross-Recessed Steel Screw 72-1604F #6-32 x Ya-Inch Cross-Recessed Steel Screw 034536-03 Foam Pad 037873-01 Spacer 039378-03 Dual-Slotted Retainer 175004-708 #8 Fiber Washer 175009-221 Plastic Spacer (for EM/ shield PCB) 72-6812S #8 x ¥-Inch Steel Machine Screw 178044-242 Grommet 178045-442 Snap-In Fastener
Jreland-Built Upright and Sit-Down Cabinets* 72-6624S #6 x 1 %2-Inch Cross-Recessed Pan-Head Tapping Screw 74-5608NN #6-32 x Y2-Inch Spacer 75-99516 #6-32 Nut/Washer Assembly 034536-02 Foam Pad 039157-02 Dual-Slotted PCB Retainer 175004-706 #6 Fiber Washer 175004-708 #8 Fiber Washer 72-6812S #8 x ¥-Inch Steel Machine Screw 178020-750 Nylon Spacer
*Not shown in illustration
3-35
3-36 Figure 3-19 Central Processing Unit (CPU) Printed-Circuit Board Assembly A039185-21 B o
a
rs
o
n /
i tH F) i
a
He ue Oy ae it j q
R
“Tal
ee
= a
cm gag = e ue BN
- a eed | ioe! Ta gp el Ts oy
(a=! 2 & u g LJ EE
ae i a 7 Be El aie) &
Apoidea “WiLN3OI jOS3d TIV OL 391 Maintenance, Repair, and Parts Pole Position
Pole Position Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List
Assemblies and components in the following parts list are shown in Figure 3-19.
| Designator | Description | Part No. |
Capacitors
| C2-C5 | 0.01,F, 100 V Radial-Lead Mylar Capacitor | 21-101103 | |
| cé | 33 pF, 100 V Radial-Lead Epoxy-Dipped Mica Capacitor | 128002-330 | |
| c7 | 0.1nF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| cg | 10pF, 25 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250106. | |
| C10 | O.1pnF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| cH | 47F, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-160476 | |
| C12 | 0.1nF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| C13 | 0.01pF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 | |
| C14, C15 | O.1nF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| C16-C23 | 0.01pF, +80%, -20%, 25 V Cerami | isc Axial-Lead Capacitor | 122005-103 |
| C24, C25 | 0.1,nF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 | |
| C26 | 47yF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-160476 | |
| C27, C28 | 0.0022uF, +10%, 100 V Radial-Lead Plastic Film Capacitor | 121022-222 | |
| C29, C30 | 0.022nF, 100 V Radial-Lead Mylar Capacitor | 21-101223 | |
| C31, C32 | 0.01pF, +80%, -20%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122005-103 | |
| C33, C34 | 0.047yF, 100 V Radial-Lead Mylar Capacitor | 21101473 | |
| C35 | 0.022uF, 100 V Radial-Lead Mylar Capacitor | 21-101223 | |
| C36 | 0,0047yF, 100 V Radial-Lead Mylar Capacitor | 21-101472 | |
| C37 | 0.001,F, 100 V Radial-Lead Mylar Capacitor | 21-101102 | |
| C38 | 0.0047,F, 100 V Radial-Lead Mylar Capacitor | 21-101472 | |
| C39, C40 | 0.01yF, 100 V Radial-Lead Mylar Capacitor | 21-101103 | |
| C41 | 47yF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-160476 | |
| C42, C43 | 0,0047yF, 100 V Radial-Lead Mylar Capacitor | 21-101472 | |
| C44, C45 | 0.001,F, 100 V Radial-Lead Mylar Capacitor | 21-101102 | |
| C46 | 470uF, 16 V Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 | |
| C47-C56 | 22uF, 35 V Aluminum Electrolytic Fixed Axial-Lead Capacitor Acceptable | 24-350226 |
substitute is part no. 24-100477
| C57-C84 | O.1pF, +10%, 25 V Ceramic-Disc Axial-Lead Capacitor | 122002-104 |
| c82 | 0.001yF, 100 V Radial-Lead Mylar Capacitor | 21-101102 |
Diodes
| CRI | Type-MV5053 Light-Emitting Diode | 38-MV5053 |
| CcR2 | 6.2 V, +5%, 1 W Type-1N4735A Zener Diode | 131009-001 |
| CR3-CR5 | 100 V, Type-1N914 Switching Diode | 31-1N914 |
| CR6 | 3.9 V +5%, Type-1N748A Zener Diode | 131000-002 |
| CR7-CR12 | 100 V, Type-1N914 Switching Diode | 31-1N914 |
Integrated Circuits
| 2N | Type-12L6 Programmable-Array Logic 1 | 137316-001 |
| 3A | Type-Z8002 16-Bit Microprocessor | 137275-001 |
| 3C | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 3F,3H | Custom Integrated Circuit 10 | 137281-001 |
(Continued on next page)
Maintenance, Repair, and Parts Pole Position
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 3M, 4C | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 4F, 4H | Custom Integrated Circuit 10 | 137281-001 |
| 4M | Type-74LS373 Integrated Circuit | S7-74LS373 |
| 4N | Type-Z8002 16-Bit Microprocessor | 137275-001 |
| 5A | Type-74LS74 Integrated Circuit | S7-TALS74 |
| 5C | Type-12L6 Programmable-Array Logic 1 | 137280-001 |
| 5D | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 5E | Type-74LS244 Integrated Circuit | S7-T4LS244 |
| 5d | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 5K | Type-74LS244 Integrated Circuit | 37-74LS244 |
| 5L | Type-74LS368 Integrated Circuit | 137168-001 |
| 5M | Type-74LS158 Integrated Circuit | 137203-001 |
| 5N | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 6A | Type-74LS161 Integrated Circuit | 37-74LS161 |
| 6C | Type-74LS74 Integrated Circuit | S7-74LS74 |
| 6D-6F | Type-74LS367 Integrated Circuit | 37-74LS367 |
< 6H > Custom Integrated Circuit 08 137186-001
| 6J, 6K | Type-74LS157 Integrated Circuit | 37-74LS157 |
| 6L | Type-74LS109 Integrated Circuit | 37-74LS109 |
| 6M | Type-74LS00 integrated Circuit | 37-74LS00 |
| 6N | Type-74S163 Integrated Circuit | 137274-001 |
| 7c | Type-10L8 Programmable-Array Logic 3 | 137279-001 |
| 7D | Type-Z80A 8-Bit Microprocessor | 137194-001 |
| 7M | Custom Integrated Circuit 07 | 137193-001 |
| 7N | Type-74S04 Integrated Circuit | 37-74S04 |
| 8D | Type-74LS138 Integrated Circuit | 137177-001 |
| 8E | Type-74LS259 Integrated Circuit | 37-74LS259 |
| 8F | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 8H | Custom Integrated Circuit 08 | 137186-001 |
| 8J | Type-ADC0804 Integrated Circuit | 137273-001 |
| 8K | Type-4066 Integrated Circuit | 37-4066 |
| 8L | Type-4584B Integrated Circuit | 37-4584B |
| 8M | Type-74S04 Integrated Circuit | 37-74S04 |
| 9E | Custom Integrated Circuit 52 | 137284-001 |
| SFA | Custom Integrated Circuit 54 | 137285-001 |
| 9FB | Type-LM324 Integrated Circuit | 37-LM324 |
| 9H | Custom Integrated Circuit 06 | 137192-001 |
| 9K | Custom Integrated Circuit 53 | 137188-001 |
| 9M | Custom Integrated Circuit 51 | 137187-001 |
| 10A | Type-74LS138 Integrated Circuit | 137177-001 |
| 10C | Type-74LS374 Integrated Circuit | 37-74LS374 |
| 10D | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 10E, 10F | Type-74LS283 Integrated Circuit | 137204-001 |
| 10H, 10J | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 10K, 10L | Type-4066 Integrated Circuit | 37-4066 |
| 1A | Type-74LS174 Integrated Circuit | S7-74LS174 |
| 11C | Type-7497 Integrated Circuit | 37-7497 |
| NE | Type-74LS273 Integrated Circuit | 37-74LS273 |
(Continued on next page)
3-38
Maintenance, Repair, and Parts Pole Position
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 11F | Type-4051 Integrated Circuit | 137277-001 |
| 11H | Type-74LS174 Integrated Circuit | S7-74LS174 |
| tJ | Type-74LS273 Integrated Circuit | 37-TALS273 |
| 11K-11M | Type-4066 Integrated Circuit | 37-4066 |
| 12A | Type-74LS174 Integrated Circuit | S7-74LS174 |
| 12B | Type-7497 Integrated Circuit | 37-7497 |
| 12C | Type-74LS161 Integrated Circuit | S7-74LS161 |
| 12D | Type-74LS393 Integrated Circuit | 37-74LS393 |
| 12H, 12J, 12M | Type-LM324 Integrated Circuit | 37-LM324 |
Random-Access Memories
| 7E | CMOS Random-Access Memory | 137278-001 |
| 7), 7K | Random-Access Memory | 137199-001 |
Read-Only Memories
| cg | Electrically Programmable Read-Only Memory* | 136014-106 |
| 3E | Electrically Programmable Read-Only Memory* | 136014-103 |
| 3L | Electrically Programmable Read-Only Memory* | 136014-101 |
| 4E | Electrically Programmable Read-Only Memory* | 136014-104 |
| 4L | Electrically Programmable Read-Only Memory* | 136014-102 |
| 7F | Electrically Programmable Read-Only Memory | 136014-116 |
| 7H | Electrically Programmable Read-Only Memory* | 136014-105 |
| 7L | Programmable Read-Only Memory | 136014-117 |
| 11D | Programmable Read-Only Memory | 136014-118 |
| 12E | Electrically Programmable Read-Only Memory* | 136014-111 |
| 12F | Electrically Programmable Read-Only Memory* | 136014-110 |
Resistors
| R41 | 2200, +5%, % W Resistor | 110000-221 |
| R2-R8 | 2.2k2, +5%, V4 W Resistor | 110000-222 |
| RQ | 1k@, +5%, VY W Resistor | 110000-102 |
| R10-R16 | 2.2kQ, +5%, Ya W Resistor | 110000-222 |
| R17-R20 | 1kQ, 45%, % W Resistor | 110000-102 |
| R21-R26 | 1kQ, +5%, Ya W Resistor | 110000-102 |
| R27-R34 | 2.2kQ, +5%, Ys W Resistor | 110000-222 |
| R35 | 1kQ, 45%, % W Resistor | 110000-102 |
| R36-R38 | 2.2kQ, +5%, V4 W Resistor | 110000-222 |
| R39-R43 | 1kQ, +5%, Vv W Resistor | 110000-102 |
| R45 | 479, +5%, %4 W Resistor | 110000-470 |
| R46, R47 | 1kO, 45%, Ya W Resistor | 110000-102 |
| R49 | 2200, +5%, Vs W Resistor | 110000-221 |
| Rs0 | 1kQ, +5%, %s W Resistor | 110000-102 |
| R51 | 2200, +5%, v4 W Resistor | 110000-221 |
| R52 | 4700, +5%, Ya W Resistor | 110000-471 |
| R53 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R54 | 4700, +5%, Y% W Resistor | 110000-471 |
| R55, R56 | 1kO, 45%, Ys W Resistor | 110000-102 |
| R57-R60 | 4700, +5%, v4 W Resistor | 110000-471 |
(Continued on next page)
3-39
Maintenance, Repair, and Parts Pole Position
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R61 | 4.7kQ, +5%, V4 W Resistor | 110000-472 |
| R62 | 10 kQ, +5%, Ys W Resistor | 110000-103 |
| R63 | 22 kf, +5%, % W Resistor | 110000-223 |
| R64 | 47 kQ, +5%, 4 W Resistor | 110000-473 |
| R65 | 4.7kQ, +5%, Ys W Resistor | 110000-472 |
| R66 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R67 | 22 kQ, +5%, %4 W Resistor | 110000-223 |
| R68 | 47 kQ, +5%, Va W Resistor | 110000-473 |
| R69 | 4.7kQ, +5%, Ys W Resistor | 110000-472 |
| R70 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R71 | 22 kQ, +5%, Vs W Resistor | 110000-223 |
| R72 | 47kQ, +5%, vs W Resistor | 110000-473 |
| R73 | 4.7 kQ, +5%, Ys W Resistor | 110000-472 |
| R74 | 10 kQ, +5%, V4 W Resistor | 110000-103 |
| R75 | 22 kQ, +5%, Va W Resistor | 110000-472 |
| R76 | 47kQ, +5%, Ya W Resistor | 110000-473 |
| R77-R80 | 1kQ, +5%, % W Resistor | 110000-102 |
| R81 | 2200, +5%, Ys W Resistor | 110000-221 |
| R82 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R83 | 4702, +5%, Ya W Resistor | 110000-471 |
| R84 | 1kQ, +5%, Ya W Resistor | 110000-102 |
| R85 | 2.2kQ, +5%, V4 W Resistor | 110000-222 |
| R86 | 3302, +5%, % W Resistor | 110000-331 |
| R87 | 1kQ, +5%, % W Resistor | 110000-102 |
| R88 | 22 kQ, +5%, Vs W Resistor | 110000-223 |
| R89 | 100 k2, +5%, % W Resistor | 110000-104 |
| R90-R92 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R93, R94 | 3300, +5%, V4 W Resistor | 110000-331 |
| R95 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R96 | 4.7kQ, +5%, Va W Resistor | 110000-472 |
| R97 | 2200, +5%, ¥% W Resistor | 110000-221 |
| R98 | 4.7kQ, +5%, Va W Resistor | 410000-472 |
| R99 | 2200, +5%, 4 W Resistor | 110000-221 |
| R101 | 2.2 kQ, +5%, Ys W Resistor | 110000-222 |
| R102, Ri04 | 1kQ, 45%, V4 W Resistor | 110000-102 |
| R103 | 4.7 kQ, +5%, Va W Resistor | 110000-472 |
| R106 | 1kQ, +5%, Y4 W Resistor | 110000-102 |
| R107 | 4.7kQ, +5%, Vs W Resistor | 110000-472 |
| 108-115 | 1kQ, +5%, % W Resistor | 110000-102 |
| R16 | 1.5k0, +5%, Ys W Resistor | 110000-152 |
| Rt17 | 1kQ, +5%, Vs W Resistor | 110000-102 |
| R18 | 4.7kQ, +5%, VY W Resistor | 110000-472 |
| R119 | 10 kQ, +5%, Y% W Resistor | 110000-103 |
| R120, R121 | 22 kQ, +5%, % W Resistor | 110000-223 |
| R122 | 120 kQ, +5%, ¥4 W Resistor | 110000-124 |
| R123 | 4702, +5%, Va W Resistor | 110000-471 |
| R124 | 47 kQ, +5%, % W Resistor | 110000-473 |
| R125 | 12 kQ, +5%, % W Resistor | 110000-123 |
(Continued on next page)
3-40
Pole Position Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R126 | 4.7kQ, +5%, % W Resistor | 110000-472 |
| R127, R128 | 2.2kQ, +5%, Va W Resistor | 110000-222 |
| R129, R130 | 3.3kQ, +5%, Vs W Resistor | 110000-332 |
| R131 | 10 kQ, 45%, Y% W Resistor | 110000-103 |
| R132 | 22kQ, +5%, Ya W Resistor | 110000-223 |
| R133 | 15 kQ, +5%, V4 W Resistor | 110000-153 |
| R134 | 120 kQ, +5%, Ys W Resistor | 110000-124 |
| R135 | 4702, +5%, % W Resistor | 110000-471 |
| R136 | 47 k&, +5%, 4 W Resistor | 110000-473 |
| R137 | 15 kQ, +5%, Ya W Resistor | 110000-153 |
| R138 | 10 kO, +5%, % W Resistor | 110000-103 |
| R139 | 22 kQ, +5%, V4 W Resistor | 110000-223 |
| R140 | 180 kQ, +5%, % W Resistor | 110000-184 |
| R141 | 4700, +5%, % W Resistor | 110000-471 |
| A142, R143 | 22 kQ, +5%, v4 W Resistor | 110000-223, |
| R144-R151 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R152 | 47 k2, +5%, Ya W Resistor | 110000-473 |
| R153 | 4700, +5%, % W Resistor | 110000-471 |
| R154 | 10kQ, +5%, % W Resistor | 110000-103 |
| R155 | 82k, +5%, Ys W Resistor | 110000-823 |
| R156, R157 | 47 kQ, +5%, V4 W Resistor | 110000-473 |
| R158 | 22kQ, +5%, Ys W Resistor | 110000-223 |
| R159 | 47k2, +5%, Vs W Resistor | 110000-473 |
| R160 | 100 KO, +5%, % W Resistor | 110000-104. |
| R161-R165 | 2.2kQ, +5%, Ya W Resistor | 110000-222 |
| R166 | 1kQ, +5%, % W Resistor | 110000-102 |
| R167 | 2.2kQ, +5%, v4 W Resistor | 110000-222 |
| R168 | 4.7kQ, +5%, Vs W Resistor | 410000-472 |
| R169 | 220 kO, +5%, % W Resistor | 110000-224 |
| R170 | 390 kO, +5%, vs W Resistor | 110000-394 |
| R171 | 4.7 kQ, +5%, V4 W Resistor | 110000-472 |
| R172 | 15kQ, +5%, Vs W Resistor | 110000-153 |
| R173 | 47kQ, +5%, % W Resistor | 110000-473 |
| R174 | 33kQ, +5%, V4 W Resistor | 110000-333 |
| R175 | 10kQ, +5%, % W Resistor | 110000-103 |
| R176 | 47 kQ, +5%, Ys W Resistor | 110000-473 |
| R177 | 1kQ, +5%, % W Resistor | 110000-102 |
| R178 | 75 kQ, +5%, Ya W Resistor | 110000-752 |
| R179 | 330 k@, +5%, % W Resistor | 110000-334 |
| R180, R181 | 47 kf, +5%, % W Resistor | 110000-473 |
| R182 | 1kQ, +5%, V4 W Resistor | 110000-102 |
| R183 | 22kQ, +5%, Vs W Resistor | 110000-223 |
| R184 | 15 kQ, +5%, Vs W Resistor | 110000-153 |
| R185, | 10 kO, +5%, % W Resistor | 110000-103 |
| R186 | 1kQ, +5%, % W Resistor | 110000-102 |
| R187 | 330kQ, +5%, 4 W Resistor | 110000-334 |
| R188 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R189, R190 | 47 kQ, +5%, Ya W Resistor | 110000-473 |
(Continued on next page)
Maintenance, Repair, and Parts Pole Position
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| Ri91 | 1k, +5%, 4 W Resistor | 110000-102 |
| R192 | 75kQ, +5%, V4 W Resistor | 110000-753 |
| R193 | 15 kQ, +5%, Ya W Resistor | 110000-153 |
| R194 | 47 kQ, +5%, Ya W Resistor | 110000-473 |
| R195 | 10 kQ, +5%, %4 W Resistor | 110000-103 |
| R196 | 1kQ, +5%, % W Resistor | 110000-102 |
| R197, R198 | 47 kQ, +5%, v4 W Resistor | 110000-473 |
| R199 | 1kQ, +5%, Vs W Resistor | 110000-102 |
| R200 | 47 kQ, +5%, Ya W Resistor | 110000-473 |
| R201 | 15 kQ, +5%, Ya W Resistor | 110000-153 |
| R202 | 10 k2, +5%, V4 W Resistor | 110000-103 |
| R203 | 1kQ, +5%, % W Resistor | 110000-102 |
| R204, R205 | 47 kQ, +5%, Ys W Resistor | 110000-473 |
| R206 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R207 | 20 kQ, +5%, Va W Resistor | 110000-203 |
| R208 | 10 kQ, +5%, Ys W Resistor | 110000-103 |
| R209 | 20 k®, +5%, % W Resistor | 110000-203 |
| R210 | 10 kO, +5%, Y% W Resistor | 110000-103 |
| Ratt | 20k, +5%, Ys W Resistor | 110000-203 |
| R2i2 | 10 kQ, +5%, Y% W Resistor | 110000-103 |
| R213 | 20 kQ, +5%, Va W Resistor | 110000-203 |
| R214 | 10 kQ, +5%, V4 W Resistor | 110000-103 |
| R215 | 20 kQ, +5%, Ya W Resistor | 110000-203 |
| R216 | 10 kQ, +5%, % W Resistor | 10000-103 |
| R217 | 20 kQ, +5%, % W Resistor | 110000-203 |
| R218 | 10 kQ, +5%, Ya W Resistor | 110000-103 |
| R219 | 20 kQ, +5%, Ya W Resistor | 110000-203 |
| R220 | 27k, +5%, V4 W Resistor | 110000-273 |
| R223 | 1kQ, +5%, % W Resistor | 110000-102 |
| R225-R231 | 1kQ, +5%, Ya W Resistor | 410000-102 |
| R231-R238 | 2.2k0, +5%, % W Resistor | 110000-222 |
| R239-R244 | 1kQ, +5%, Ys W Resistor | 110000-102 |
| R245 | 1002, +5%, % W Resistor | 110000-101 |
| R246 | 150 kQ, +5%, Va W Resistor | 110000-154 |
| 1E | 2.2kQ, +2%, Dual-Inline-Package Resistor Network | 118003-222 |
| ON | 1k, +2%, Dual-Inline-Package Resistor Network | 118003-102 |
Sockets
| 3A | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| 3E, 3F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 3H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 3b | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4E, 4F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4b | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4N | 40-Contact Medium-Insertion-Force integrated Circuit Socket | 79-42C40 |
(Continued on next page)
Pole Position Maintenance, Repair, and Parts
Central Processing Unit Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No, |
| 6H-9H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 7D | 40-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C40 |
| 7E, 7F | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 7H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 7M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 8A | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42028 |
| 8C | 28-Contact Medium-Iinsertion-Force Integrated Circuit Socket | 79-42C28 |
| 9c | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 9E | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C42 |
| OFA | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 9K | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42042 |
| 9M | 42-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C42 |
| 12E, 12F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
Switches
| JA | 8-Station, SingleThrow, Dual-Inline-Package Bit Switch | 66-118PIT |
| 9L | 8-Station, SingleThrow, Dual-Inline-Package Bit Switch | 66-118P IT |
Transistors
| Qi | Type-2N3906 40 V, 1 W, PNP Transistor | 33-2N3906 |
| Q2 | Type-2N3904 60 V, 350 mW, NPN Transistor | 34-2N3904 |
| Q3 | Type-MPS-A92 300 V, 500 mA, PNP Transistor | 33-MPSA92 |
| Q4 | Type-2N3904 60 V, 350 mW, NPN Transistor | 34-2N3904 |
| Q5, Q6 | Type-2N6044 80 V, 8 A, Darlington NPN Transistor | 34-2N6044 |
Miscellaneous
| BT | 3.6 V, 100 mA Nickel-Cadmium Battery | 171028-001 |
| wi | Lead-Spring Socket Terminal | 179131-001 |
Test Point Acceptable substitute is part no. 020670-01 179051-001 Jumper Staple 150009-001
| Q5, Q6 | Nylon Snap-In Fastener | 81-4302 |
- Acceptable substitute is part no. 137276-003.
Pole Position Maintenance, Repair, and Parts
a fs #8. ' eas} 2 eG [™ me) fee] Gao ; = ce) bee: Bier] Ze] feel (phe i moe x fee | fee H cao ' 2 ss EE ies) F s iue2s7 ae | E es fisses) fEeSe*) D a ies] SS] c Ss ps] rater) B
eat A
Figure 3-20 Pole Position Video Printed-Circuit Board Assembly A039187-21 B
3-44
Pole Position Maintenance, Repair, and Parts
Pole Position Video Printed-Circuit Board Assembly Parts List
| Designator | Description | Part No. |
Capacitors
| C2 | 470 uF, 25 V Aluminum Electrolytic Axial-Lead Capacitor | 24-250477 |
C3-C17 22 uF, 16 V Aluminum Electrolytic Axial-Lead Capacitor Accepiable substitute is part no. 24-250226 24-160226
| C18-C57 | 0.1 uF, + 80, -20%, 50 V Ceramic Disk Radial-Lead Capacitor | 122002-104 |
| C58. | 68 pF, 100 V, Mica Capacitor | 128002-680 |
| C59 | 22 pF, 100 V, Mica Capacitor | 128002-220 |
Diodes
| CR1 | Type-MV5053 Light-Emitting Diode | 38-MV5053 |
| CR2 | Type-1N4735A, 6.2 V, 1 W Zener Diode | 131009-001 |
Inductors
| L1-L3 | 1H, V2 W Inductor | 141007-001 |
| L4 | 100 wH, + 10% Inductor | 141002-001 |
Integrated Circuits
| 2A | Type-74LS138 Integrated Circuit | 137177-001 |
| 2E | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 2H | Type-74LS139 Integrated Circuit | 37-74LS139 |
| 2d | Type-74LS10 Integrated Circuit | 37-74LS10 |
| 2K | Type-74LS368 Integrated Circuit | 137168-001 |
| 3B | Type-74LS283 Integrated Circuit | 137204-001 |
| 3c | Type-74LS283 integrated Circuit | 137204-001 |
| 3D | Type-74LS283 Integrated Circuit | 137204001 |
| 3H | Type-74LS175 Integrated Circuit | 37-74LS175 |
| SJ, 4d | Type-74LS174 Integrated Circuit | 37-7ALS174 |
| 3K | Type-74LS283 Integrated Circuit | 137204-001 |
| 3L | Type-74LS283 Integrated Circuit | 137204-001 |
| 3M | Type-74LS02 Integrated Circuit | 37-74LS02 |
| 4B | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 4c | Type-74LS367 Integrated Circuit | 37-74LS367 |
| 4H | Type-74L$157 Integrated Circuit | 37-74LS157 |
| 4k | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 4M, 5M | Type-74LS298 Integrated Circuit | 137201-001 |
| AN, 5N | Type-74LS283 Integrated Circuit | 137204-001 |
| 5B | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 5C | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 5D | Type-74LS174 Integrated Circuit | 37-74LS174 |
| SE | Type-74LS245 Integrated Circuit | 37-74LS245 |
| SF, 6F | Type-74LS245 Integrated Circuit | 37-74LS245 |
| 5H | Type-74LS175 Integrated Circuit | 37-74LS175, |
| 5d | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 6A | Type-74S04 integrated Circuit | 37-74S04 |
| 6B | Type-74LS368 Integrated Circuit | 137168-001 |
| 6C | Type-74LS08 Integrated Circuit | 37-74LS08 |
| 6H | Type-74LS245 Integrated Circuit | 37-74LS245 |
| 6d | Type-74LS245 Integrated Circuit | 37-74LS245 |
| 6K | Type-74LS245 integrated Circuit | 37-74LS245 |
| 6M, 7M | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 7B | Type-74S163 Integrated Circuit Acceptable substitute is part no. | 137274-001 |
137287-001 or -002
| 7c | Type-74S04 Integrated Circuit | 37-74S04 |
| 7D | Type-74LS32 Integrated Circuit | 37-74LS32 |
(Continued on next page)
3-45
Maintenance, Repair, and Parts Pole Position
Pole Position Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| 7L | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 8B | Type-74S00 Integrated Circuit | 37-74S00 |
| 8C,9C | Type-74LS157 Integrated Circuit | 37-74LS157 |
| 8D | Type-74S8158 Integrated Circuit | 137312-000 |
| 8E | Type-74LS 158 Integrated Circuit | 137203-001 |
| 8L,9L | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 9B | Type-74LS20 Integrated Circuit | 37-74LS20 |
| 9D | Type-74LS298 Integrated Circuit | 137201-001 |
| 9E, 10E | Type-74LS257 Integrated Circuit | 37-74LS257 |
| 9H | Type-748161 Integrated Circuit | 137287-001 |
| ou | Type-74S161 integrated Circuit | 137287-001 |
| 9K | Type-7497 Integrated Circuit | 37-7497 |
| 9M, 10M | Type-74LS283 Integrated Circuit | 137204-001 |
| ON | Type-74LS85 Integrated Circuit | 37-74LS85 |
| 10B | Type-74LS74 Integrated Circuit | 37-74LS74 |
| 100 | Type-74LS174 Integrated Circuit | 37-74LS 174 |
| 10D | Type-74LS368 Integrated Circuit | 137 168-001 |
| 10H | Type-74S161 Integrated Circuit | 137287-001 |
| 100 | Type-74S161 Integrated Circuit | 137287-001 |
| 10K | Type-74S161 Integrated Circuit | 137287-001 |
| 40L | Type-74S161 Integrated Circuit | 137287-001 |
| 10N | Type-74LS85 integrated Circuit | 37-74LS85 |
| 11B | Type-74107 Integrated Circuit Acceptable substitute is part no. | 37-74107 |
137169-001
| 11F | Type-74LS174 Integrated Circuit | 37-74LS174 |
| 1H | Type-74LS174 Integrated Circuit | 37-74LS 174 |
| WW | Type-74LS273 Integrated Circuit | 37-74LS273 |
| 11K | Type-74LS139 Integrated Circuit | 37-74LS139 |
| ML | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 11M | Type-74LS373 Integrated Circuit | 37-74LS373 |
| 12B | Type-74LS08 Integrated Circuit | 37-74LS08 |
| 12F | Type-74LS86 Integrated Circuit | 37-74LS86 |
| 13F | Type-74LS20 Integrated Circuit | 37-74LS20 |
For -21 version only
| 2F | Type-07 Custom Integrated Circuit | 137193-001 |
| 3N | Type-02 Custom Integrated Circuit | 137190-001 |
| 4D | Type-09 Custom Integrated Circuit | 137282-001 |
| BL, 6L | Type-03 Custom Integrated Circuit | 137283-001 |
| 7E | Type-04 Custom Integrated Circuit | 137191-001 |
| 8N | Type-02 Custom Integrated Circuit | (437190-001 |
| 13H | Type-02 Custom Integrated Circuit | 1377907001 |
Random-Access Memories
| 3E, 4E | Random-Access Memory (200 ns) Acceptable substitute is part no. | 137198-001 |
137211-001 (150 ns)
| SF, 4F | Random-Access Memory (200 ns) Acceptable substitute is part no. | 137198-001 |
137211-001 (150 ns)
| 7F, 8F | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| 7H, 8H | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| TJ, Bd | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| 7K, 8K | Type-2114-2 (200 ns) Random-Access Memory | 90-7036 |
| OF, 10F | 55 ns Random-Access Memory | 137 199-001 |
(Continued on next page)
3-46
Pole Position
Pole Position Video Printed-Circuit Board Assembly Parts List, continued Maintenance, Repair, and Parts
| Designator | Description | Part No. |
Programmable Read-Only Memories
| 2B | Type-82S129(17) Programmable Read-Only Memory | 136014-144 |
| 2c | Type-82S 129(16) Programmable Read-Only Memory | 136014-143 |
| 2D | Type-82S 129(15) Programmable Read-Only Memory | 136014-142 |
| 4L | Type-82S137(12) Programmable Read-Only Memory | 136014-145, |
| 5K | Type-82S 129(11) Programmabie Read-Only Memory | 136014-141 |
| 6D | Type-82S123(14) Programmable Read-Only Memory | 136014-136 |
| 6E | Type-82$123(13) Programmable Read-Only Memory | 136014-135 |
| 8M | Type-82$129(10) Programmable Read-Only Memory | 136014-140 |
| 11C | Type-82S129(9) Programmable Read-Only Memory | 136014-139 |
| 11D | Type-82S129(8) Programmable Read-Only Memory | 136014-138, |
| NE | Type-82S129(7) Programmable Read-Only Memory | 136014-137 |
| 12H | Type-828137(6) Programmable Read-Only Memory | 136014-146 |
For -27 version only
| 2b | Electrically Programmable Read-Only Memory Acceptable | 136014-127 |
substitute is part no. 136014-158
| 2M | Electrically Programmable Read-Only Memory Acceptable | 136014-128 |
substitute is part no, 136014-159
| 2N | Electrically Programmable Read-Only Memory | Acceptable | 136014-134 |
substitute is part no. 137205-001 a =
| 6N | Electrically Programmable Read-Only Memory | Acceptable | Cc | 136014-133 7 |
substitute is part no. 137205-007 me
| 7N | Electrically Programmable Read-Only Memory | Acceptable | 136014-132 |
substitute is part no. 137205-001
| TiN | Electrically Programmable Read-Only Memory Acceptable | 136014-231 |
substitute is part no. 136014-131
| 12d | Electrically Programmable Read-Only Memory Acceptable | 136014-120 |
substitute is part no, 136014-151
| 12K | Electrically Programmable Read-Only Memory Acceptable | 136014-122 |
substitute is part no. 136014-153
| 12L | Electrically Programmable Read-Only Memory Acceptable | 136014-124 |
Substitute is part no. 136014-155
| 12N | Electrically Programmable Read-Only Memory Acceptable | 136014-126 |
substitute is part no. 136014-157
| 13J | Electrically Programmable Read-Only Memory Acceptable | 136014-119 |
substitute is part no. 136014-150
| 13K | Electrically Programmable Read-Only Memory Acceptable | 136014-121 |
substitute is part no. 136014-152
| 13L | Electrically Programmable Read-Only Memory Acceptable | 136014-123 |
substitute is part no. 136014-154
| 13N | Electricaily Programmable Read-Only Memory Acceptable | 136014-125 |
substitute is part no. 136014-156 Resistors
| R1-RQ | 2.2 kQ, +5%, Ya W Resistor | 110000-222 |
| R10-R24 | 1kQ, +5%, Y%4 W Resistor | 110000-102 |
| R25-R40 | 470 Q, +5%, % W Resistor | 110000-471 |
| R41-R48 | 4.7 kQ, +5%, Ya W Resistor | 110000-472 |
| R49-R52 | 1kQ, +5%, % W Resistor | 110000-102 |
| RS55-R58 | 1kQ, +5%, % W Resistor | 116000-102 |
| R59 | 220 2, +5%, % W Resistor | 110000-221 |
| R60 | 470 Q, +5%, % W Resistor | 110000-471 |
(Continued on next page)
3-47
Maintenance, Repair, and Parts Pole Position
Pole Position Video Printed-Circuit Board Assembly Parts List, continued
| Designator | Description | Part No. |
| R61 | 1kQ, +5%, Y% W Resistor | 110000-102 |
| R62 | 2.2 kQ, +5%, Va W Resistor | 110000-222 |
| R63 | 1kQ, +5%, % W Resistor | 110000-102 |
| R64, R65 | 82 2, +5%, % W Resistor | 110000-820 |
| R66 | 220 0, +5%, v4 W Resistor | 110000-221 |
| R67 | 470 0, + 5%, v4 W Resistor | 110000-471 |
| R68 | 1k, +5%, % W Resistor | 110000-102 |
| R69 | 2.2 kQ, +5%, Ys W Resistor | 110000-222 |
| R70 | 1kQ, +5%, % W Resistor | 110000-102 |
| R71, R72 | 82 0, +5%, % W Resistor | 110000-820 |
| R73 | 220 2, +5%, %4 W Resistor | 110000-221 |
| R74 | 470 2, +5%, % W Resistor | 110000-471 |
| R75 | 1kQ, +5%, % W Resistor | 110000-102 |
| R76 | 2.2 kQ, +5%, Ya W Resistor | 110000-222 |
| R78, R79 | 82 0, +5%, % W Resistor | 110000-820 |
| R80 | 1kQ, +5%, % W Resistor | 110000-102 |
| Rat | 100 2, +5%, % W Resistor | 110000-101 |
| R82-R85 | 1kQ, +5%, % W Resistor | 110000-102 |
| R86 | 220 9, +5%, ¥ W Resistor | 110000-221 |
| R87,-R98 | 1kQ +5%, % W Resistor | 110000-102 |
| R99 | 10 kQ, +5%, % W Resistor | 110000-103 |
| R100 | 220 0, +5%, V4 W Resistor | 110000-221 |
| R101 | 10 kQ, +5%, ¥4 W Resistor | 110000-103 |
| R102 | 1.5 kQ, +5%, % W Resistor | 110000-152 |
| R103-R105 | 82 0, +5%, V4 W Resistor | 110000-820 |
| 1B | 2.2 kQ, +2%, 15-Element, Duat-Inline Package Resistor Pack | 118003-222 |
| 1K | 2.2 kQ, +2%, 15-Element, Dual-inline Package Resistor Pack | 118003-222 |
Sockets
| 2F | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| aL | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 2M | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 2N | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| 3E, 4E | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C24 |
| SF, 4F | 24-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C24 |
| 3N | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 4D | 24-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C24 |
| 5L, 6L | 18-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C018 |
| 6N, 7N | 24-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-420 24 |
| 7E | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 8N | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 11N | 24-Contact Medium-Insertion-Force integrated Circuit Socket | 79-42C24 |
| 12J, 13d | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 |
| 12K, 13K | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 12L, 13L | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
| 12N, 13N | 28-Contact Medium-insertion-Force Integrated Circuit Socket | 79-42C28 |
| 13H | 28-Contact Medium-Insertion-Force Integrated Circuit Socket | 79-42C28 |
Transistor
| Q1-Q4 | Type-2N3904, 60 V, 1 W, NPN Transistor | 34-2N3904 |
| Q5-Q7 | Type-2N3906, 40V, 1W, PNP Transistor | 33-2N3906 |
Miscellaneous Test Points Acceptable substitute is part no. 020670-01 179051-002
| Y1B | 24.576 MHz Crystal Acceptable substitute is part no. 144004-002 | 144004-003 |
3-48
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific wilten permission of Alar, Inc., Sunnyvale, CA. This drawing is ‘only conditionally issued, ‘and neither receipt ‘nor possession theteot confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right {o reproduce this drawing or ay part there. Except for manufacture by vendors of Alar! Inc. and for manufacture under the corporation's writen license, ‘no right to reproduce this drawing is granted or the subject mat ter thereof unless by written agreement with or waitten permission from the corporation. Maintenance, Repair, and Parts
R24,10,7W]
220 | Rel, \/2w cle yb 4zo_*
Goci aoc Rt
Figure 3-21 Regulator/Audio I! PCB Assembly U.S.-Built Cabinet A035435-01 G
3-49
Maintenance, Repair, and Parts
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This <drawing is only conditionally Issued, and neither receipt nor Possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design oF technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof uniess by written agreement with or written permission from the corporation. Pole Position
R24,10,7W
Figure 3-22 Regulator/Audio Il PCB Assembly lreland-Built Cabinet A035435-05 A
3-50
Pole Position Maintenance, Repair, and Parts
Regulator/Audio Il PCB Assembly Parts List
Assemblies and components in the following parts list are shown in Figures 3-21 and 3-22.
| Designator | Description | Part No. |
Capacitors
For -01* and -05** versions
| C1 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| C2 | 0.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 |
| C8 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| C13 | 1000 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250108 |
For -01 version
| C3 | 0.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 29-088 |
| C4 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| C5 | 0.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable | 100015-103 |
substitute is part no. 122005-103
| ce | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| C7 | 0.001 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 |
| C9, C10 | 3300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-350338, |
| ci | 0.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 29-088 |
| C12 | 470 uF, 25 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-250477 |
| C14 | 0.01 uF, 25 V Minimum, Ceramic-Disc Axial-Lead Capacitor Acceptable | 100015-103 |
substitute is part no. 122005-103
| C15 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| foals} | 0.001 pF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122002-102 |
| C17 | 0.22 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 122004-224 |
| C18, C19 | 3300 uF, 35 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-350338 |
| C20, C21 | 0.1 uF, 25 V, Ceramic-Disc Axial-Lead Capacitor | 29-088 |
| C22, C23 | 1 uF, 50 V, Aluminum Electrolytic Fixed Axial-Lead Capacitor | 24-500105 |
Diodes
For -01 and -05 versions
| cR1 | Type-1N4002, 1 A, 100 V Silicon Rectifier Diode | 31-1N4002 |
| CR4 | Type-1N4002, 1 A, 100 V Silicon Rectifier Diode | 31-1N4002 |
Integrated Circuits
For -01 and -05 versions
| Qi | Type-LM305, 5 V, Linear Voltage Regulator | 37-LM305, |
For -01 version
| Q5 | TypeTDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit | 137151-002 |
| Q7 | Type-TDA2002A, 8 W, Linear Audio Amplifier Integrated Circuit | 137151-002 |
(Continued on next page)
*Acceptable substitutes are A035435-02 or -04. **Acceptable substitutes are A035435-01, -02, or -04.
3-51
Maintenance, Repair, and Parts Pole Position
Regulator/Audio || PCB Assembly Parts List, continued
| Designator | Description | Part No. |
Resistors
For -01 and -05 versions
| R1 | 270 2, +5%, % W Resistor | 110000-271 |
| R3 | 33 2, +5%, % W Resistor | 110000-330 |
| R4 | 100 2, +5%, % W Resistor | 110000-101 |
| R5 | 2.7 2, +5%, 1 W Resistor | 110009-027 |
| R6 | 3.9 kQ, +5%, V4 W Resistor | 110000-392 |
| R7 | 7.5 kQ, +5%, % W Resistor | 110000-752 |
| R8 | 1 kQ Vertical PCB-Mounting Cermet Potentiometer Acceptable | 19-315102 |
substitute is part no. 119002-102
| R24 | 0.1 2, +3%, 7 W Wirewound Resistor | 19-100P1015 |
| R29, R30 | 10 2, +5%, % W Resistor | 110000-100 |
For -01 version
| RQ | 220 2, +5%, V2 W Resistor | 110001-221 |
| R10 | 12, +5%, % W Resistor | 110000-010 |
| R11 | 10 2, +5%, % W Resistor | 110000-100 |
| R12 | 100 2, +5%, % W Resistor | 110000-101 |
| R13, R14 | 10 k2, +5%, % W Resistor | 110000-103 |
| R19 | 12, +5%, % W Resistor | 110000-010 |
| R20 | 10 2, +5%, 4 W Resistor | 110000-100 |
| R21 | 220 2, +5%, Ye W Resistor | 110001-221 |
| R22 | 100 2, +5%, % W Resistor | 110000-101 |
| R27, R28 | 1kQ, +5%, % W Resistor | 110000-102 |
Transistors
For -01 and -05 versions
| Q2 | Type-TIP32 PNP Power Transistor | 33-TIP32 |
| Q3 | Type-2N3055 NPN Silicon Transistor | 34-2N3055 |
Mechanical Parts
For -01 and -05 versions
| J6 | 6-Position Connector Receptacle | 79-58306 |
| J7 | 9-Position Connector Receptacle | 79-58308 |
| Q3 | #6-32 x ¥2-Inch Cross-Recessed Pan-Head Corrosion-Resistant Steel | 72-1608C |
Machine Screw
| Q2, Q3 | #6-32 Nut/Washer Assembly | 75-99516 |
| Q2 | Thermally Conductive Silicon Insulator | 78-16014 |
| Q3 | Thermally Conductive Silicon Insulator | 78-16008 |
| Q5 | #6-32 x %4-Inch Binder-Head Nylon Screw | 75-F60405 |
Heat Sink 034531-01 Test Point Acceptable substitute is part no. 020670-01 179051-001
For -01 version
| J8 | 4-Position Connector Receptacle | 79-58354 |
| Q8 | #6 x %Inch Cross-Recessed Pan-Head Thread-Forming Type-AB Zinc- | 72-6606S, |
Plated-Steel Screw
3-52
Pole Position
NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specitic written permission of Atari Inc., Sunnyvale, CA. This drawing is ‘only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical intor- ‘mation shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of ‘Atari, Inc.,.and for manufacture under the corporation's written license, no right to reproduce this drawing is granted or the subject matter thereof unless by writlen agreement with or written permission from the corporation
Opn
Figure 3-23 EMI Shield PCB Assembly Maintenance, Repair, and Parts
Goer Go c22 Cl Go czs CO oO c2a4 Ci} Toes cas Cor (Sica eo {co oO oo co on ts Con cs! Cop Ceciz, ca2z Gi+ cocs <33 CD Corie 3+ 150 cs co fet cre co Gaz ton oD tsa co cs9 cen | J co o40 CT} Coc2!
ocai foc Gocas eas, 470°F S45 cae, ,.470FF 151647 4707 Goc4
7 Gocs4 Gocss f
fl
A037667-01 A
3-53
Maintenance, Repair, and Parts Pole Position
EMI Shield PCB Assembly Parts List
Components in the following parts list are shown in Figure 3-23.
| Designator | Description | Part No. |
Capacitors
| C1-C5 | 0.1 pF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
C6, C7 0.01 pF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor Acceptable substitute is part no. 122005-104 122005-103
| C8-C10 | 0.01 pF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C12 | 0.01 pF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C13-C15, | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C16 | 0.01 wF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C17-C24 | 0.1 zF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C25 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
C27 0.01 »F, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor Acceptable substitute is part no. 122005-104 122005-103
| C28-C31 | 0.01 pF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C32, C33 | 0.1 nF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C34-C39 | 0.01 uF, +80, -20%, 25 V Ceramic-Disk Radial-Lead Capacitor | 122005-103 |
| C40-C43, | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C44 | 0.471 uF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-471 |
| C45 | 0.001 pF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-102 |
| C46, C47 | 0.471 nF, +80, -20%, 100 V Ceramic-Disk Radial-Lead Capacitor | 122016-471 |
| C48 | 0.1 uF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
| C54, C55 | 0.1 wF, +80, -20%, 50 V Ceramic-Disk Radial-Lead Capacitor | 122002-104 |
Connectors P19 30-Pin Card-Edge Connector Acceptable substitute is part number 179046-030 179073-030 P20 44-Pin Card-Edge Connector Acceptable substitute is part number 179046-044 179073-044
3-54
Pole Position Maintenance, Repair, and Parts
H. Power Supply Assembly
A021084-xx (Voltage plugs)
29-053 ccnsctoo— D 03454401 (Fuse block cover)
79-4411001 (Fuse post)
78-70501SC. (Capacitor bracket) 46-2017002 (Fuse)
29-053 (Capacitor) ‘A095891.02 (Fuse harness assy.) \ 034482-02 (Chassis)
46-301203 (Fuse) A
037639-01 (Label)
78-2708 (Bushing)
A034630-01 (Filter Assy.) (Fuse block) 037641-01 ‘ 46-2014002 78-70501SC (Label) ( (Fuses) (Bracket)
79-15021001 ‘A035890-01 (Terminal block) \ (Power harness) ‘A034629-01 3A-MDA3501 (AC harness) (Rectifier)
Figure 3-24 Power Supply Assembly A0376721-04 &-05 G
3-55
Maintenance, Repair, and Parts Pole Position
Power Supply Assembly Parts List
Assemblies and components in the following parts list are shown in Figure 3-24.
Part No, Description (Reference Designations in Bold)
| A021084-01 | Voltage Plug for 100V | (90-110 VAC) | (violet) |
| A021084-02 | Voltage Plug for 120V | (105-135 VAC) | (yellow) |
| A021084-04 | Voltage Plug for 220V | (200-240 VAC) | (blue) |
| A021084-05. | Voltage Plug for 240V | (220-260 VAC) | (brown) |
A034629-01 AC Harness Assembly
| A034630-01 | RF! Filter Assembly | _(FL1—designation not marked) |
A035888-01 Upright and Cabaret Transformer Assembly (11) Acceptable substitute is part no. A035888-02 A035890-01 Power Harness Assembly (J2) A035891-02 Fuse Harness Assembly (F2-F6) 29-053 27,000 uF 15V DC Electrolytic Capacitor (C1) 3A-MDA3501 Bridge Rectifier, Type MDA 3501 (CR1) 46-2014002 4A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse (F2, F4-F6) 46-2017002 7 A, 250 V, 3AG Slow-Blow Glass Cartridge-Type Fuse (F1) 46-301253 25 A, 32 V, 3AG Slow-Blow Glass Cartridge-Type Fuse (F3) 78-2708 Nylon Type 6/6 Hole Bushing with %-Inch Inside Diameter x %,-Inch Outside Diameter x 14-Inch Thick 78-70501SC 2-Inch Diameter Capacitor Mounting Bracket (C1)
| 79-15021001 | 2-Circuit Single-Row Terminal Block | (located under F4) |
79-3206 5-Position 3AG Fuse Block with %4-Inch Quick-Disconnect Terminals (F2-F6) 79-4411001 Panel-Mounting Non-Indicating 3AG Cartridge-Type Fuse Post (F1) 03448202 Power Supply Chassis 03454401 Fuse Block Cover (F2-F6)
| 037639-03, -04 | Label for Fuse Value | (F1) |
| 037641-01 | Label for Fuse Values | (F2-F6) |
A037671-04 power supply has the 120 V plug. A037671-05 has the 100 V, 220 V and 240 V plugs. A037671-06 has the 220 V and 240 V plugs.
3-56
Pole Position
Glossary of Terms
AC Alternating current; from zero it rises. to a maximum positive level, then passes through zero again to a maximum negative level. ACTIVE STATE The true state of a signal. For example: The active state for START is low.
ADDRESS A value that identifies a specific location of data in memory; normally expressed in hexadecimal notation. ANALOG Measurable in an absolute quantity (as opposed to on or off). Analog devices are volume controls, light dimmers, stereo amplifiers, etc. ANODE The positive (arrow) end of a diode. AMPLIFIER A device used to increase the strength of an applied signal. AMPLITUDE The maximum instantaneous value of a waveform pulse from zero. ASTABLE Having no normal state. An astable device will free-run or oscillate as long as operating voltage is applied. The oscillation frequency is usually controlled by external circuitry. AUXILIARY COIN SWITCH A momentary-contact pushbutton switch with a black cap located on the utility panel. The auxiliary coin switch adds credits to the game without activating the coin counter. BEZEL A cut, formed, or machined retention device, such as the conical device used to mount a pushbutton switch to a control panel, or the formed device used to frame the video display screen. BIDIRECTIONAL Able to send or receive data on the same line (e.g., the data bus of a microprocessor). BINARY A number system that expresses all values by using two digits (0 and 1). BIT A binary digit; expressed as a 1 or ao. BLANKING Turning off the beam on a cathoderay tube during retrace. BLOCK DIAGRAM A drawing in which functional circuitry units are represented by blocks. Very useful during initial troubleshooting. BUFFER
- An isolating circuit designed to eliminate the reaction of a driven circuit on the circuits driving it (e.g., a buffer amplifier).
- A device used to supply additional drive capability. BUS An electrical path over which information is transferred from any of several sources to any of several destinations.
CAPACITOR A device capable of storing electrical energy. A capacitor blocks the flow of DC current while allowing AC current to pass.
CATHODE The negative end of a diode. CHIP An integrated circuit comprising many circuits on a single wafer slice. CLOCK A repetitive timing signal for synchronizing system functions.
COINCIDENCE Occurring at the same time. COIN COUNTER A 6-digit electro-mechanical device that counts the coins inserted in the coin mechanism(s). COIN MECHANISM A device on the inside of the coin door that inspects the coin to determine if the correct coin has been inserted. COMPLEMENTARY Having opposite states, such as the outputs of a flip-flop. COMPOSITE SYNC Horizontal and vertical synchronization pulses that are bused together into a single signal. This signal provides the timing necessary to keep the display in synchronization with the game circuitry. Glossary
COMPOSITE VIDEO Complete video signal from the game system to drive the display circuitry, usually comprising H SYNC, V SYNG, and the video. CREDIT One play for one person based on the game switch settings. CRT Cathode-ray tube. DATA General term for the numbers, letters, and symbols that serve as input for device processing. DARLINGTON A two-transistor amplifier that provides extremely high gain. Dc Direct current, meaning current flowing in one direction and of a fixed value. DEFLECTION YOKE Electro-magnetic coils around the neck of a cathode-ray tube. One set of coils deflects the electron beam horizontally and the other set deflects the beam vertically. DIAGNOSTICS A programmed routine for checking circuitry. For example: the self-test is a diagnostic routine. DIODE A semiconductor device that conducts in only one direction. DISCRETE Non-integrated components, such as resistors, capacitors, and transistors. DMA Direct memory access. DMA is a process of accessing memory that bypasses the microprocessor logic. DMA is normally used for transferring data between the input/output ports and memory. DOWN TIME The period during which a game is malfunctioning or not operating correctly due to machine failure. EAROM Electrically alterable read-only memory (see ROM). The EAROM is a memory that can be changed by the application of high voltage. FLYBACK A step-up transformer used in a display to provide the high voltage.
Glossary
GATE
- A circuit with one output that responds when and only when a certain combination of pulses is present at the inputs.
- A circuit in which one signal switches another signal on and off.
- To contro! the passage of a pulse or signal. HARNESS A prefabricated assembly of insulated wires and terminals ready to be attached to a piece of equipment. HEXADECIMAL A number system using the equivalent of the decimal number 16 as a base. The symbols 0-9 and A-F are usually used. IMPLODE To burst inward; the inward collapse of a vacuum tube.
Input/Output. IRQ Interrupt request. IRQ is a control signal to the microprocessor that is generated by external logic. This signal tells the microprocessor that external logic needs attention. Depending on the program, the processor may or may not respond. LED The abbreviation for a light-emitting diode. LOCKOUT COIL Directs coins into the coin return box when there is no power to the game. LOGIC STATE The binary (1 or 0} value at the node of a logic element or integrated circuit during a particular time. Also called the logic level. The list below shows the voltage levels corresponding to the logic states (levels) in a TTL system. Logic 0, Low = 0 VDC to +0.8 VDC Grey Area (Tri-State Level) = +0.8 VDC to +2.4 VDC Logic 1, High = +24 VDC to +5 VDC MULTIPLEXER A device that takes several lowspeed inputs and combines them into one high-speed data stream for simuitaneous transmission on a single line.
GL2 NMI Non-maskable interrupt. NMI is a request for service by the microprocessor from external logic. The microprocessor cannot ignore this interrupt request. PAGE A subsection of memory. A read-only memory device (see ROM) is broken into discrete blocks of data. These blocks are called pages. Each block has X number of bytes. PCB The abbreviation for a printed-circuit board. PHOTOTRANSISTOR A transistor that is activated by an external light source. POTENTIOMETER
- A resistor that has a continuously moving contact which is generally mounted on a moving shaft. Used chiefly as a voltage divider. Also called a pot (slang).
- An instrument for measuring a voltage by balancing it against a known voltage. RAM Random-access memory. A device for the temporary storage of data. RASTER-SCAN DISPLAY Adisplay system whereby images are displayed by continuously scanning the cathode-ray tube horizontally and vertically with an electron beam. The display system controls the intensity of the electron beam. RETRACE In a raster-scan display, retrace is the time during which the cathoderay tube electron beam is resetting either from right to left or from bottom to top. RESISTOR A device designed to have a definite amount of resistance. Used in circuits to limit current flow or to provide a voltage drop. ROM Read-only memory. A device for the Permanent storage of data. SIGNATURE ANALYSIS A process of isolating digital logic faults at the component level by means of special test equipment called signature analyzers. Basically, signature analyzers (e.g., the ATARI® CAT Box) converi lengthy bit Pole Position
streams into four-digit hexadecimal signatures. The signature read by the analyzer at each circuit node is then compared with the known good signature for that node. This process continues until a fault is located. TROUBLESHOOT The process of locating and repairing a fault. VECTOR A line segment drawn between specific X and Y coordinates on a cathode-ray tube. WATCHDOG A counter circuit designed to protect the microprocessor from self-destruction if a program malfunction occurs. If a malfunction does occur, the counter applies continuous pulses to the reset line of the microprocessor, which causes the microprocessor to keep resetting. X-Y DISPLAY A display system whereby images are displayed with vectors. ZENER DIODE A special diode used as a regulator. Its main characteristic is breaking down at a specified reverse-bias (Zener) voltage.
Pole Position 5th printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below. No postage stamp is necessary if mailed in the U.S.A.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm O Distributor
Address 0) Operator
City State Zip Ui Other. Area Code Phone
First told
Necessary
[ BUSINESS REPLY MAIL
BEST CLASS PERMIT NO. 1004 SUNNYVA i
POSTAGE WILL BE PAID BY ADDRESSEE if mailed in the United States
Atari, Inc. Attn.: Field Service/Coin-Op Division P. O. Box 427 Sunnyvale, California 94086
Second fold
wol4 aBpa siy) ade,
Pole Position 8th printing
YOUR COMMENTS, PLEASE!
Your comments will assist Atari in improving our publications. The comments are an important part of preparing for revisions of game manuals. Please write in the space below.
If you have any technical questions about certain ATARI games products, or are requesting additional publications, we will immediately forward your note to the appropriate person.
Page: Comments:
Fill in if you wish a reply:
Name.
Firm © Distributor
Address OC Operator
City State Zip C Other.
Area Code Phone
First fold
Atari Ireland Limited Attn.: Field Service/Coin-Op Division Tipperary Town, Ireland Attach Necessary Postage
Second told
eBpe sy) odey ‘wold
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
This page carries no recoverable text. It is a drawing or a photograph. See the original scan.
RR RE EE
> > >
Pidsee Sates, Nahas alee Sates, Silas Natee Naha? | Na
Warranty
Seller warrants that its printed-circuit boards and parts thereon are free from defects in material and workmanship under normal use and service for a period of ninety (90) days from date of shipment. Seller warrants that its video displays (in games supplied with displays) are free from defects in material and workmanship under normal use and service for a period of thirty (30) days from date of shipment. None of the Seller's other products or parts thereof are warranted.
\f the products described in this manual fail to conform to this warranty, Sellers’ sole liability shall be, at its option, to repair, replace, or credit Buyer's account for such products which are returned to Seller during said warranty period, provided:
- Seller is promptly notified in writing upon discovery by Buyer that said products are defective;
- Such products are returned prepaid to Sellers’ plant; and
- Seller's examination of said products discloses to Seller's satisfaction that such alleged defects existed and were not caused by accident, misuse, neglect, alteration, improper repair, installation or improper testing.
In no event shall Seller be liable for loss of profits. loss of use, incidental or consequential damages.
Except for any express warranty set forth in a written contract between Seller and Buyer which contract supersedes the terms of this order, this warranty is expressed in lieu of all other warranties expressed or implied, including the implied warranties of merchantability and fitness for a particular purpose, and of all other obligations or liabilities on the Seller's part, and it neither assumes nor authorizes any other person to assume for the Seller any other liabilities in connection with the sale of products under this order.
The use of any non-Atari parts may void your warranty, according to the terms of the warranty. The use of any non-Atari parts may also adversely affect the safety of your game and cause injury to yourself and others. Be very cautious in using non-Atari-supplied components with our games, in order to insure your safety.
Atari distributors are independent, being privately owned and operated. In their judgment they may sell parts or accessories other than Atari parts or accessories. Atari cannot be responsible for the quality, suitability or safety of any non-Atari part or any modification including labor which is performed by such distributor.
This document is and contains contidential trade secret information of Atari, Inc.
This document is loaned under confidential custody for the sole purpose of operation, maintenance or repair of Atari equipment and may not be used by or disclosed to any person for any other purpose whatever, and remains the property of Atari, Inc.
Neither it nor the information it contains may be reproduced, used, or disclosed to persons not having a need to know consistent with the purpose of the loan, without written consent of Atari, Inc. : : : : : : :
ATARI, INC. 790 SYCAMORE DRIVE ® P.O. BOX 906 MILPITAS, CALIFORNIA 95035 408/942-3100 ¢ TELEX 35-7488