CATHODE RAY TOMES

VS Top Gun

Top Gun (handheld) (Konami, 1989) · Document · 5 pages · 8 sections · original scan

Page 1

fe KONAMI

INSTRUCTION MANUAL

COPYRIGHT © 1987 PARAMOUNT PICTURES CORPORATION. ALL RIGHTS RESERVED. “TOP GUN” LOGO IS A TRADEMARK OF PARAMOUNT PICTURES CORPORATION. KONAMI AUTHORIZED USER. UNDERLYING SOURCE CODE © 1987 KONAMI. “TOP GUN ANTHEM” COPYRIGHT © 1986 BY FAMOUS MUSIC CORPORATION. ALL RIGHTS RESERVED. USED BY PERMISSION.

KONAMI® IS A REGISTERED TRADEMARK OF KONAMI INDUSTRY CO., LTD. DEVELOPED UNDER LICENSE FROM NINTENDO FOR PLAY EXCLUSIVELY ON THE VS. SYSTEM.

Page 2

KONAMI TOP GUN KIT CONTENTS

1 — Top Gun Sub-Board 1 — Top Gun Marquee 1 — Clear Acrylic Marquee (must be cut to size) 1 — Player Instruction Sheet 1 — Instruction Manual

TOP GUN COMES WITH AN OVERSIZE MARQUEE AND MARQUEE PLEXI GLASS BECAUSE IT MAY BE INSTALLED IN ANY VS. CABINET. DUAL-SYSTEM, UNI SYSTEM, AND THE PACMAN VERSION.

MARQUEE

(Wear protective glasses while trimming Marquee)

1/8” Acrylic Marquee should be cut to fit your game. DO NOT remove protective mask until this is done.

One way of cutting your Marquee is as follows: (Be sure to protect painted side of Marquee from any surface which may scratch or mar finish).

CUTTING WITH A KNIFE OR SCRIBER Acrylic sheet up to 3/16” thick may be cut by a method similar to that used for cutting window glass. Use a scriber of some kind—a scribing knife such as the one pictured, a metal scriber, an awl or even a sturdy craft knife—to score the sheet. Draw the scriber several times (7 or 8 times for a 3/16” thick piece) along a straight edge held firmly in place. It is best not to remove the protective masking. Make the cuts carefully using firm, even pressure. For best results make each stroke cleanly off the edge of the sheet. Then clamp the acrylic sheet or hold it rigidly under a straight edge with the scribe mark hanging just over the edge of a table. Protect your hands with a cloth, and apply a sharp downward pressure to the other side of the sheet. It will break along the scratch. Scrape the edges to smooth any sharp corners. This method is not recommended for long breaks or thick material.

Always draw the scribing knife along a straight edge. Break sheet over edge of table after scribing.

HARDWARE INSTALLATION INSTRUCTIONS

*With power OFF, remove the NINTENDO MDS PCB from the cabinet.

*Remove existing eproms, PPU, and CPU from the side you wish to install the Top Gun sub-board.

If the Top Gun is to be installed in a Uni-System, carefully remove the CPU from location 8J (save the CPU-it will be installed on the sub PCB). Remove the PPU location 8F and any eproms from locations 6A, 6B, 6C, 6D, 8A and 8B.

lf Top Gun is to be installed in a dual system, right screen, follow Uni-System instructions. If installed in left screen, carefully remove the CPU from location 2J (save the CPU-it will be installed on the sub-board). Remove the PPU from location 2F and any eproms from locations 1A, 1B, 1C, 1D, 2A and 2B. *Inspect the capacitors in location C3, C11, C30 and C47 on the NINTENDO MDS PCB. They should be bent down to prevent a short circuit with the sub-board.

*Insert the CPU (RP2A03) into the sub-board at location U8 (insure correct polarity).

*Install the sub-board into the NINTENDO MDS PCB by applying pressure with your palm down on the subboard until it sits securely. Inspect both 40 pin sockets for any bent pins. Insure correct polarity. The PPU must sit into location 2F or 8F only.

*Set dip switch on the NINTENDO MDS PCB. SW1 for dual system left monitor. SW2 for uni-system and dual system right monitor.

Page 3

TOP GUN: DIP SWITCH SETTINGS

DIP SW123|45678
COIN/CREDITqwWOFFOFFOFF
112OFFOFFON
113OFFONOFF
2iOFFONON
3ONOFFOFF
4nONOFFON
5/1ONONOFF
FREE PLAYONONON
NUMBER OF LIVES3(Max. 12 lives)OFF
BOUGHT BY COIN2(Max. 9 lives)ON
BONUS1) 30,000OFFOFF

SETTINGS — every 50,000

2) 50,000OFFON

every 100,000

3) 100,000ONOFF

every 150,000

4) 200,000ONON

every 200,000 EASY OFF HARD ON

OFF DEMO SOUND ON ON

WU WL fp

not used for one- monitor game. ‘SW2—Sub Right side for twomonitor game.

: UL)

| i S

NG GUN SUB BOARD

NINTENDO MDS PCB

Page 4

PART # 701400 USER INFORMATION

WARNING

F.C.C. REGULATION COMPLIANCE

THIS KIT IS INTENDED FOR USE ONLY ON COIN-OPERATED VIDEO GAMES MANUFACTURED AFTER OCTOBER 1, 1983 WHICH HAVE BEEN VERIFIED FOR COMPLIANCE WITH RE- QUIREMENTS IN PART 15 OF F.C.C. RULES FOR A CLASS A COMPUTING DEVICE.

IMPROPER CONNECTION OF THIS KIT OR CONNECTION TO ANY OTHER GAME NOT SO MANUFACTURED OR VERIFIED FOR COMPLIANCE MAY CAUSE UNACCEPTABLE INTER- FERENCE TO RADIO AND T.V. RECEPTION, REQUIRING THE OPERATOR TO TAKE WHATEVER STEPS ARE NECESSARY TO CORRECT THE INTERFERENCE.

“a KONAMI"

815 Mittel Drive, Wood Dale, Illinois 60191 Telephone: (312) 595-1443, Telex: 6871385 KONAM UW, Fax: (312) 595-2973

Page 5

S005 Fow 3009 (Beis ar v95 P ‘ye th DIT INVAIAIS| INVN | POL OS Vi alle Sal Sy F778 CHIE ae F441" 934 MAIYNOM ah Woda 519 1) ‘zal ist IS = NOHYONTS anaaaaad EERE RR Gaba) o aaaanass Bi Rowwnnre gas + =s x2 at at as a S S|

> ols) NE5exxet aS roll Et Loe S nenvanre Nos TREN een aT

a t aes Rie ee b9es on an exeest inG a