CATHODE RAY TOMES

Bally Midways Standarized General Instructions (M051-00132-0000)

Standardized General Instructions (Bally/Midway) · Manual · 99 pages · 44 sections · original scan

Page 1

Bally/Midway’s

Standardized General

Instructions

‘MIDWAY MFG. CO.

10601'W. Belmont Avenue

> Franklin Park, Iinois 60131

‘MIDCO > TelexNos 72-1596) i ORM NO, M051=00132-0000~

i

Page 2
WARNING THIS GAME MUST BE GROUNDED. FAILURE TO DO SO MAY RESULT IN DESTRUCTION TO ELECTRONIC COMPONENTS.
WARNING: This equipment generates. uses. and can radiate radio frequency energy and if not and used in accordance with the instructions manual. may Cause interference to radio communications. It has been tested and found to comply with the limits for a CLASS A computing device pursuant to SUBPART J of PART 15 of FCC RULES. which are designed to provide reasonable protection against such interference when operated in a commerical environment. Operation of this equipment in a residential area is likely to cause interference in which Case the user at his own expense will be required to take whatever measures may be required tocorrect the interference.

ELECTRICAL BULLETIN: FOR ALL_ APPARATUS COVERED BY THE CANADIAN STANDARDS ASSOCIATION (CSA) STANDARD G22.2 NO. 1, WHICH EMPLOYS A SUPPLY CORD TERMINATED WITH A POLARIZED 2-PRONG ATTACHMENT PLUG.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

eeeeecue BLADES CAN BE FULLY INSERTED TO PREVENT BLADE

ATTENTION: POUR PREVENIR CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR. UNE PRISE DE COURANT OU _UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

Cily|MIDWAY Inwiles You Fo Use OUR TOLL FREE NUMBERS FOR SERVICE INFORMATION CONCERNING THIS GAME, OR ANY OTHER BALLY/MIDWAY™ GAME YOU NOW HAVE ON LOCATION.

CALL US FOR PROMPT, COURTEOUS ANSWERS TO YOUR PROBLEMS

ANSWERS TO YOUR PROBLEMS.

Continental U.S. 800-323-7182 inois Only 1-800-942-0497

© COPYRIGHT MCMLXXXIII BY BALLY/MIDWAY CO. ALL RIGHTS RESERVED. NO PART OF THIS PUBLICATION MAY BE REPRODUCED BY ANY MECHANICAL, PHOTOGRAPHIC, OR ELECTRONIC PROCESS, OR IN THE FORM OF A PHONOGRAPHIC RECORDING, NOR MAY IT BE TRANSMITTED, OR OTHERWISE COPIED FOR PUBLIC OR PRIVATE USE, WITHOUT PERMISSION FROM THE PUBLISHER. THIS MANUAL IS FOR SERVICE USE ONLY, AND NOT FOR GENERAL DISTRIBUTION. FOR PERMISSION REQUESTS, WRITE: MIDWAY MFG. CO., 10750 W. GRAND AVE., FRANKLIN PARK, IL 60131 Printed in U.S.A.

Page 3

TABLE OF CONTENTS

DESCRIPTION

I. Location and Setup Inspection Installation .-.. Game Volume Adjustment Control . Option Switch Settings ............. Cocktail Table Leg Extension Installation

ll. Maintenance and Repair Pa a 0006 | 0) tne 2.2 Cleaning sees 2.3 Fuse Replacement ... 2.4 Opening Control! Panel . 2.4.1 Upright Model .. 2.4.2 Mini Model 2.4.3 Cocktail Model ....... 2.5 Main- Display - Glass Removal 2.5.1 Upright Model 2.5.2 Mini Model 2.5.3 CocktailModel ..... 2.6 T.V.Bezel Assembly Removal . 2.6.1 Upright Model 2.6.2 Mini Model ..... 2.6.3 Cocktail Model ... 2.7 T.V. Monitor Replacement 2.7.1 Upright Model .... 2.7.2 Mini Model . 2.7.3 Cocktail Model . 2.8 Printed Circuit Board (P.C.B. ) Replacement 2.8.1 Upright Model .. 2.8.2 Mini Model . 2.8.3 Cocktail Model « 2.9 Opening the peer traction Panel 2.9.1 Upright Model . 2.9.2 Mini Model 2.10 Replacing the Game Upper Attraction Panel Lighting 2.10.1 Upright Model............. 2.10.2 Mini Model .. wees 2.11 Speaker Replacement . 2.11.1 Upright Model . 2.11.2 MiniModel . 2.11.3 Cocktail Model . 2.12 Opening the Lower Attraction Panel and Servi 2.12.1 Upright Model 2.13 Servicing the Control Panel Lighting seem 2.13.1 Upright Model 2.14 Servicing Auxiliary Lighting .. 2.14.1 Upright Model - Servicing Windshield Fluorescent Light....... 2.14.2 Upright Model - Servicing the Black Light Above Control Console .. 2.14.3 Upright Model - Servicing the Fluorescent Light Behind the Front Service Panel . PAGE

2-10

2-12

2-14 2-15 2-16 2-17 2-19 2-20 2-22 2-23 2-25 2-27 2-29 2-30 2-33 2-35 2-36 2-39 2-40 2-41 2-45 2-46 2-47 2-48 2-49 2-50 2-52 2-53 2-54 2-55

Page 4

TABLE OF CONTENTS (Continued)

DESCRIPTION PAGE

ll. Technical Troubleshooting Introduction a1 General Suggestions ..... 3-1 Harness Component Troubleshooting 31 Transformer and Line Voltage Problems 3-2 AGlossary of Microprocessor Terms 3-3

IV. Coin Door Maintenance Metal Coin Acceptor Mechanisms .....-....-0..0ceseeeeeeeee ae wevew 41 Plastic Coin Acceptor Mechanisms 43

V. T.V. Monitor Manual Introduction..... 5-1 Sympton Diagnosis ...... 5-2 Guide to Schematic Symbols » 53 Troubleshooting ......... . &5 Theory of Operation. . 5-6 Differences Between Monitors 5-7 Controls You May Not Touch 5-8 Parts Interchangeability .... 5-9 Picture Tube Interchangeability . 5-10 Wells Gardner Monitor Schematic - 1 5-12 Wells Gardner Monitor Replacement Parts List . 5-13 Electrohome Monitor Schematic-19”"..... 5-14 Electrohome Monitor Replacement Parts List 5-15, Electrohome Monitor Schematic - 13” ...... 5-16 Electrohome Monitor Replacement Parts List 5-17 Zenith Monitor - Sweep Board Schematic ..... 5-18 Zenith Monitor - Sweep Board Replacement Parts List 5-19 Zenith Monitor Main Board Schematic ............-+ 5-20 Zenith Monitor Main Boarad Replacement Parts List . . 5-21 Zenith Monitor- CRT Socket Board Dead ial Parts List . 5-22 Zenith Monitor - CRT Socket Board Schematic...... 5-23 Zenith Monitor Width Step Assy. Schematic ... . 5-24 Zenith Monitor Interconnect for Video Game Schematic 5-25

Page 5

I. Location and Setup

INSPECTION

  • Remove the game from its shipping crate.
  • Inspect the entire outside of it for any signs of damage. O Any scratches?, dents?, cracks? O Any broken controls? O Any broken glass or plastic? © Just look it over closely and make a note of any signs of damage.
  • Remove the shipping cleats from the bottom of the cabinet. O UPRIGHT MODELS ONLY: In order to help prevent easy theft of your game, you may wish to remove the Caster Wheel Assemblies from the bottom of your cabinet at this time.
  • Install the four levelers, one at each corner of the cabinet. O Level the cabinet.
  • Open the cabinet and inspect the inside of the game tor any signs of damage. See Figure 1-1. D Also check to make sure all plug-in connectors on the wire harness are firmly seated.
NOTE: ALL connectors or plugs are keyed so they will only go together when all pins are Properly lined up. O Replug any connectors found unplugged. DO NOT FORCE PLUGS ONTO CONNECTORS. DO NOT FORCE PLUGS TOGETHER. If it won't go on easily, assuming the keys are lined up, it either does not belong there or is damaged. Make sure all printed circuit boards (P.C.B.'s) are firmly seated in their connectors. See Figure 1-1. These connectors are also keyed. The P.C.B.'s will only go into them one way without being damaged.
Note the location of the game's serial number. See Figure 1-1. Check all major subassemblies to be sure they are mounted securely. These are called out in Figures 1-1 & 1-2. Power supply. Control panel(s). T.V. monitor. . Other P.C.B.'s and/or P.C.B. rack, etc. Power Chassis assembly.
  • Make a note of any problems that can’t be easily corrected.
  • Call your distributor and/or service man about your problem list.
Page 6

SERIAL = 3 ; ON/OFF NUMBER ~__ 7 Switch

Tv. MONITOR INTERLOCK SWITCH

GAME BOARD

INTERLOCK 7 OFF SWITCH Sanen

POWER SUPPLY f CHASSIS

CHASSIS . (NOT SEEN)

UPRIGHT

SERIAL NUMBER:4Ty.
(MAY BE LOCATED;‘ieVe
ON ANY CORNER)‘"aMONITOR

POWER SUPPLY CHASSIS

ix;PailCONTROL PANEL

PANEL (PLAYER 2)

(PLAYER 1) |

GAME BOARD

ON/OFF SWITCH INTERLOCK 7 SWITCH UNDER GAME ON

(INSIDE DOOR)COCKTAILPLAYER 2 SIDE

Figure 1-1 Location of Serial No., Interlock Switch, On/Oft Switch, and Major Sub-Assemblles

1-2

Page 7

CONTROL PANEL

UPRIGHT

Figure 1-2 Major Sub-Assemblles (cont. from Fig. 1-1)

INSTALLATION

  • Location requirements:

O Power: Domestic 110 V @ 60 Hz Foreign 200 V to 240 V @ 50 Hz

O Temperature: 32° to 100°F (0° to 38°C)

D Humidity: Not over 95% relative Ne

O Space required: 7) Upright 32” x 25” (81cm x 63cm) APPROX. ~ Mini 20" x 24” (50cm x 60cm) Cocktail 32” x 22" (81cm x 55cm)

O Game height: Upright 70" (175cm) APPROX. Mini 61" (153cm) Cocktail 29" ( 73cm) Figure 1-3 Interlock Switch Operation

Page 8
  • Voltage Selection: Your game is designed to work properly on the line voltage where you are located. Check your line voltage with a meter to determine what its value is. Then check the power input wires to the main power supply transformer on your game to besure they are connected to taps which correspond to your line voltage value. If the power input wires to the main power supply transformer are not connected to taps which correspond to your local line voltage, move them to the proper taps. If the line voltage in your area falls outside the upper or lower limits of the range of inputs covered by the main power supply transformer, DO NOT PLUG YOUR GAME IN until you have talked with your distributor and/or service man and obtaineda solution to this problem. Otherwise you could damage your game.

|. Interlock and power ON/OFF switches. See Figure 1-1.

O To help prevent the possibility of getting an electric shock while working inside the game cabinet, interlock switches have been installed at each cabinet access door (this DOES NOT include the coin door in the Upright and Mini models).

O When any access door is opened, the interlock switch installed there turns off all power to the game.

O Check each interlock switch for operation. After checking the line voltage in your area and determining that the input wires to the main power supply transformer: of your game are connected properly — or — after obtaining a solution to your over or under voltage problem from your distributor and/or your service man, plug the game into your A.C. wall outlet. The game ON/OFF switches for all models are located as shown in Figure 1-1. Turn the game on and allow it to warmup a few minutes. Slowly open each access door to the game (this does not include the coin door on the Upright and Mini models). As the door is opened approximately 1” (2.54cm) the power to the game should go off (the T.V. monitor, all the lights, and all sounds will stop). If this does not happen, check the interlock switch by this door to see if it has broken loose from its mounting or if it is stuck in the “ON” position. proper If the switch is found to be bad, turn the game off, unplug it, and replace the interlock switch. When done, plug the game back into the wall outlet, close the access door, and turn the game back on. After the game has warmed up, repeat the above interlock switch test. When the interlock switch is working properly and turns the power to the game off, power may be restored to the game with the access door(s) open. Take hold of the interlock switch plunger and gently pull it out to its fully extended position. THIS IS TO BE USED ONLY FOR SERVICING THE GAME. See Figure 1-3.

GAME VOLUME ADJUSTMENT CONTROL

The volume control pot is located on a P.C. board inside the game cabinet. It may be reached through the rear access door on the UPRIGHT and MINI models. On the COCKTAIL TABLE models, you will have to open the table top to reach it.

To make the sounds louder, turn the pot clockwise as you face it (74). To make the sounds less loud, turn the pot counterclockwise as you face it (F\). The exact location of this pot is noted in your game's Parts and Operating Manual.

OPTION SWITCH SETTINGS To change the option switch settings, you DO NOT have to take the CPU board out of the game. They can be easily reached through the rear access door on the Upright and Mini models. On the Cocktail Table model, you do have to open the table top to reach them. When changing any options, ALWAYS check the results by playing the game to be sure the switches have worked properly and that no switches were accidentally moved that were not meant to be. (These switches are small and this can happen.) See your game's Parts and Operating Manual for Option Switch settings and exact location of these switches.

Page 9

COCKTAIL TABLE LEG EXTENSION INSTALLATION There are two ways in which this can be accomplished: 1) the perferred method and 2) the

reali method. Both are completely covered

elow.

  • The perferred method is more labor intensive and requires 3 strong persons. Two to lift up the Cocktail Table while the third installs the Leg Extensions. A. Lift the Cocktail Table off the floor. B. Remove the Glide from each Leg. C. install a Leg Extension in each Cocktail Table Leg that you removed a Glide from. See Figure 1-4. Make sure they are tightly screwed in place. They must not be loose. D. Reinsert the 4 Glides into the bottoms of aD the Leg Extensions you just installed. See Le LEG EXTENSION Figure 1-4. E. Leg Extension installation is now complete.
  • The alternate method is less labor intensive and requires only 1 strong person to tilt the Cocktail Table onto its side without dropping it, This same person can then install the Leg Figure 1-4 Cocktail Table Leg Extension Installation Extensions. A. Tilt the Cocktail Table onto its side and lay . . . i i D. Reinsert the 4 Glides into the bottoms of it gently en the floor. Do not drop it er the Leg Extensions you just installed. See Bounee'itl Figure 1-5. By Remove the lidedromleaen ted: E. Tilt the Cocktail Table back to the upright C. Install a Leg Extension in each Cocktail position and recheck all the leg extensions Table Leg that you removed a Glide from. for tightness. They must not be loose. See Figure 1-5. Make sure they are tightly F. Leg Extension installation is now comscrewed in place. They must not be loose. plete.

LEG EXTENSION

Figure 1-5 Cocktail Table Leg Extension Installation

1-5

Page 10

II. Maintenance and Repair

2.1 INTRODUCTION

Your NEW game needs certain types of maintenance to keep it in good working order. CLEAN, well MAINTAINED games attract players and EARN MORE PROFITS.

The most important thing for you to remember is to play your game thoroughly EVERY TIME you collect money from the coin box. JUST LOOKING at your game WILL NOT tell you if ali its controls and inside parts are working correctly. ONLY being familiar with and playing your game will inform you whether or not it is working the way it should. The second most important thing you should remember is to clean the outside of the game and coin acceptor mechanisms on a regular basis.

2.2 CLEANING The outside of the game cabinet plus the metal can be cleaned with any non-abrasive household cleaner. However, the front of the T.V. monitor tube and both sides of all other glass and plastic on or in the game MUST be cleaned with anti-static cleaner ONLY. For cleaning the coin acceptors: hot soapy water may be used on the plastic ones and any household cleanser may be used on the metal ones. If you wish, special coin machine cleaners that leave no residue may be purchased from your distributor. DO NOT dry-wipe any of the plastic panels, This is because any dust that was on them can scratch their surfaces. If this has happened, anyone looking through this type of damaged plastic would feel he was looking at the game through a fog. This fogging damage CANNOT be repaired or reversed. The ONLY solution is to replace the damaged piece of Plastic.

2.3 FUSE REPLACEMENT This game contains several fuses located as shown in Figure 2-1.

  • UPRIGHT MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Chassis and the Power Supply Board Assemblies.
  • MINI MODEL: As viewed from the back, facing the cabinet, with the rear access door removed; the fuses are located on the Power Chassis and the Power Supply Board Assembiies.
  • COCKTAIL TABLE MODEL: As viewed from the coin door side of the cabinet, with the monitor tilted open to one side; the fuses are located on the Power Chassis and Power Supply Board Assemblies. Replace fuses ONLY with the type and size listed in the Illustrated Parts Breakdown Section of your game manual. See the T.V. Monitor Manual (available on request from your Distributor or the Monitor manufacturer) and/or the T.V. Troubleshooting Section of your game manual! for information on these fuses.

FUSES ON POWER CHASSIS & POWER SUPPLY PCB (TYP. ALL 3 MODELS)

Figure 2-1 Location of Fuses

Page 11

2.4 OPENING THE CONTROL PANEL 2.4.1 Upright Models 2.4.2 Mini Models 2.4.3 Cocktail Models

2-2

Page 12

2.4 OPENING THE CONTROL PANEL(S) UPRIGHT

2.4.1 UPRIGHT MODEL: (See Figure 2-2)

G_ The control panel is held in place by two or three latches. See Figure 2-2. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the front center of the control panel. Once they are released, unhook them from their latch plates To remove the control panel: Raise it up and tilt it toward you until youcan see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it from its cabling and nylon retaining strap. The control panel is now free and can be removed. Q To reinstall the control panel, reverse this procedure.

CERTAIN MODELS ONLY

Figure 2-2 Opening the Control Panel - Upright

Page 13

2.4 OPENING THE CONTROL PANEL(S) (Cont'd) MINI

2.4.2 MINI MODEL: (See Figure 2-3) O The control panel is held in place by two latches. See Figure 2-3. They are spring loaded to provide constant positive pressure on their latch plates. They can be reached through the coin door AFTER turning power to the game off. To release the latches, lift up and toward the center control panel. Once they are released, unhook them from their latch plates. O To remove the control panel: Raise it up and tilt it toward you until you can see the cable behind it. Cradling the control panel between yourself and the cabinet, disconnect it.from its cabling and nylon retaining strap. The control panel is now free and can be removed. O To reinstall the control panel, reverse this procedure.

Figure 2-3 Opening the Control Panel - Mini

2-4

Page 14

2.4 OPENING THE CONTROL PANEL(S) (Cont'd) COCKTAIL

Figure 2-4 Opening the Cocktail Game 2.4.3 COCKTAIL TABLE MODEL: (See Figures 2-4 and 2-5)

O Each control panel is held in place by several screws, two on the inside of the cabinet and LIFT three along the outside bottom edge of the CONTROL UP control panel. Turn power to the game off. | Open the coin box door and release the two REMOVE latches indicated in Figure 2-4. ‘Elen swe.

WARNING: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!

Once they’re released, unhook them from their latch plates. Grasp the table top at "A" and open it as indicated in Figure 2-4. SCREWS

1]

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which secure the control panel in place. See Figure 2-5. QO To remove the control panel(s): Disconnect it from its cabling. The control panel is now free and can be removed. O To reinstall the contro! panel, reverse this procedure. Figure 2-5 Removing the Control Panel - Cocktail

2-5

Page 15

2.5 MAIN—DISPLAY—GLASS REMOVAL

2.5.1 Upright Models 2.5.2 Mini Models 2.5.3 Cocktail Models

2-6

Page 16

2.5 REMOVAL OF THE MAIN-DISPLAY-GLASS UPRIGHT

2.5.1 UPRIGHT MODEL: (See Figure 2-6)

NOTE: In order to do this, the contro! panel MUST be removed first. O Turn the power to the game off and remove the control panel. Q This frees the main-display-glass so it can be lifted up. DISPLAY GLASS

OQ By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. 1 To reinstall the main-display-glass, reverse this procedure.

Figure 2-6 Removing the Main Display Glass - Upright :

Page 17

2.5 REMOVAL OF THE MAIN-DISPLAY-GLASS (Cont'd) UPRIGHT

2.5.1 UPRIGHT MODEL: (Cont'd)

NOTE: In order to do this, the control panel MUST be removed first. See the "Upright Model” procedure. O Turn the pwer to the game off and remove the control panel.

OD Remove the screws which secure the glass DISPLAY

clamping plate. See Figure 2-7. GLASS Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. O By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. See Figure 2-7. QO To reinstall the main-display-glass, reverse this procedure.

GLASS CLAMPING PLATE

Figure 2-7 Removing the Main Display Glass - Upright

2-8

Page 18

2.5 REMOVAL OF THE MAIN-DISPLAY-GLASS (Cont'd) UPRIGHT

2.5.1 UPRIGHT MODEL: (Cont'd)

NOTE: In order to do this, the control panel MUST be removed first. See the “Upright Model” procedure. C Turn the power to the game off and remove the control panel. This frees the main-display-glass so it can be lifted up. Q Grasp the main-display-glass in the bottom center, lift up slightly and pull it toward you about an inch, let it down just farenough so you can get hold of its top edge with your other hand and lift it out of the game. See Figure 2-8. Q To reinstall the main-display-glass, reverse this procedure.

Figure 2-8 Main Display Glass Removal

2-9

Page 19

2.5 REMOVAL OF THE MAIN-DISPLAY-GLASS (Cont'd) MINI

2.5.2 MINI MODEL: (See Figure 2-9.)

NOTE: In order to do this, the control panel MUST be removed first. See the "Mini Model” procedure. QO Turn the power off to the game and remove the control panel. DISPLAY GLASS O Remove the screws which secure the glass clamping plate. Lift out the glass clamping plate. This frees the main-display-glass so it can be lifted up. O By putting your finger in the hole in the middle of the main-display-glass support, you can lift it up and out. O Reverse this procedure to reinstall the maindisplay-glass.

Figure 2-9 Removing the Main Display Glass - Mini

2-10

Page 20

2.5 REMOVAL OF THE MAIN-DISPLAY-GLASS (Cont'd) COCKTAIL

2.5.3 COCKTAIL TABLE MODEL: (See Figure 2-10)

NOTE: This may be done with the table top in the open or the,closed position. If you decide to open GLass the table top, TURN THE POWER TO THE GAME OFF FIRST. OQ Remove the screws which secure the table top glass clamps in place. O Remove the table top glass. O To reinstall the table top glass, simply reverse this procedure.

Figure 2-10 Removing the Top Glass - Cocktail

Page 21

2.6 T.V. BEZEL ASSEMBLY REMOVAL

2.6.1 Upright Models 2.6.2 Mini Models

2.6.3 Cocktail Models

2-12

Page 22

2.6 T.V. BEZEL ASSEMBLY REMOVAL UPRIGHT

2.6.1 UPRIGHT MODEL: (See Figure 2-11)

NOTE: In order to do this, the main-display-glass MUST be removed first. See the Upright Model procedure. a Loosen the screws which secure the T.V. bezelglass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the above mentioned screws and the bezel with four bezel-glass-clamps may be removed. To reinstall the T.V. bezel assembly, reverse this procedure,

2-13 T.V. BEZEL GLASS CLAMPS

Figure 2-11 Removing the T.V. Bezel - Upright

Page 23

2.6 T.V. BEZEL ASSEMBLY REMOVAL (Cont'd) MINI

2.6.2 MINI MODEL: (See Figure 2-12)

NOTE: In order to do this, the main-display-glass MUST be removed first. See the "Mini Model” Procedure. 1 Remove the screws which secure the T.V. bezel assembly and lift it out.
NOTE: Use the hole in the center of the maindisplay-glass support to grasp it. Reverse this procedure to reinstall the T.V. bezel assembly.

REMOVE: SCREWS

Figure 2-12 Removal of T.V. Bezel Assembly

2-14

Page 24

2.6 T.V. BEZEL ASSEMBLY REMOVAL (Cont'd) COCKTAIL

2.6.3 COCKTAIL TABLE MODEL: (See Figure 2-13)

NOTE: In order to do this, the main-display-glass MUST be removed first. See "Cocktail Model” procedure.

O Loosen the screws which secure the T.V. bezel glass-clamps in place. Move the clamps to the side and the bezel glass may be removed. Remove the screws which secure the bezel assembly to the table top and the bezel with four bezel-glass-clamps may be removed. Q To reinstall the T.V. bezel assembly, simply reverse this procedure.

Figure 2-13 Removing the T.V. Bezel - Cocktail

2-15

Page 25

2.7. T.V. MONITOR REPLACEMENT 2.7.1 Upright Models 2.7.2 Mini Models 2.7.3 Upright Models

Page 26

2.7. T.V. MONITOR REPLACEMENT UPRIGHT

WARNING: High voliages may exist in any tele- REMOVE (4) vision unit, even with the power disconnected. Use EXTREME CAUTION and do noi touch electrical parts or-the T.V. yoke area with your hands or with metal objects held in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such | protection.
DANGER: The TV. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted insfead on the floor of the cabinet). When servicing the monitor ona test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANSFORMER.

2.7.1. UPRIGHT MODEL: (See Figure 2-14) | Turn power off to the game.

O Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE, Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above “Upright Model” procedure. With the removal of only four bolts, the T.V. monitor and its mounting channels will be loose. The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet's right and left sides. The monitor is removed by sliding it out the back of the cabinet. See Figure 2-14. O To reinstall the T.V. monitor, reverse this procedure. Q After replacing the T.V. monitor, be sure to run the game Self-Test.

Figure 2-14 Removing the Monitor - Upright

Page 27

2.7 T.V. MONITOR REPLACEMENT (Cont'd) UPRIGHT

WARNING: High voltages may exist in any television unit, even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held inyour hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The T.V. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANS- FORMER. REMOVE
  • BOLTS 2.7.1 UPRIGHT MODEL: (See Figure 2-15) (Cont'd) QO Turn power off to the game.

Open the rear access door. O Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass MUST be removed. See above "Upright Model” procedure. O With the removal of only four bolts, the T.V. monitor will be loose. a

CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will not fall out of the cabinet. Figure 2-15 Removing the Monitor - Upright

O The monitor mounting channels slide on top of and against two metal guides mounted to the cabinet's right and left sides. The monitor is removed by sliding it out the back of the cabinet. O To reinstall the T.V. monitor, reverse this procedure. O After replacing the T.V. monitor, be sure to run the game Self-Test.

2-18

Page 28

2.7 T.V. MONITOR REPLACEMENT (Cont'd) MINI

WARNING: High voltages may exist in any television unit. even with the power disconnected. Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The T.V. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANS- FORMER. REMOVE
  • BOLTS

2.7.2 MIN! MODEL: (See Figure 2-16) Turn the power off to the game. 1 Open the rear access door. Q Completely disconnect the T.V. monitor from all its cabling. DON’T FORGET THE CHASSIS GROUND WIRE. Before removing the T.V. monitor, the maindisplay-glass and bezel MUST be removed. See above "Mini Model” procedure. With the removal of only four bolts, the T.V. monitor will be loose.

CAUTION: BE SURE to support the T.V. monitor from the rear while removing the four bolts so it will not fall out of the cabinet.

The monitor is removed by supporting it and pulling straight back as shown in Figure 2-16. QO To reinstall the T.V. monitor, reverse this procedure. After replacing the T.V. monitor, be sure to run the game Self-Test. Figure 2-16 Removing the Monitor - Mini

2-19

Page 29

2.7 T.V. MONIOR REPLACEMENT (Cont'd) COCKTAIL

WARNING: High voltages may exist in any tele- | vision unit, even with the power disconnected. J Use EXTREME CAUTION and do not touch electrical parts or the T.V. yoke area with your hands or with metal objects held in your hands! J In addition, BE SURE TO USE HEAVY GLOVES when handling the monitor. You could cut your hands on the metal T.V. chassis without such protection.
DANGER: The T.V. monitor DOES NOT contain an isolation transformer on its chassis (it is mounted instead on the floor of the cabinet). When servicing the monitor on a test bench, YOU MUST ISOLATE THE MONITOR FROM AC VOLTAGE WITH AN ISOLATION TRANS- FORMER.

2.7.3 COCKTAIL TABLE MODEL: (See Figure 2-18)

O Turn the power off to the game.

Q Open the coin box door and release the two latches indicated in Figure 2-17.

WARNING: The sight hand late! the HIGH VOLTAGE on t is very close to monitor.

CLAMPS O Once the latches are released, unhook them from their latch plates. O Grasp the table top at "A" and open it as indicated in Figure 2-17.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

Remove the screws which hold the table top glass clamps in place. Remove the table top glass. Lift out the T.V. bezel assembly. See above “Cocktail” procedure. Completely disconnect the T.V. monitor from all its cabling. DON'T FORGET THE CHASSIS GROUND WIRE.

Remove the screws holding the T.V. monitor chassis to the "L” by the door hinge(s). See Figure 2-18. Close the Cocktail Table and re-latch it.

Remove the screws which secure the T.V. monitor mounting brackets to the edges of the slot cut in the table top. See Figure 2-18.

Pry up the end of each monitor mounting bracket with a screwdriver or similar tool until you can grasp them both.

Figure 2-17 Opening the Cocktail Game

Page 30

2.7 T.V. MONITOR REPLACEMENT (Cont'd) COCKTAIL

C Lift the T.V. monitor straight up and out of the table top being VERY CAREFUL notto bump the ‘ REMOVE 6 neck of the picture tube. pain O To reinstall the T.V. monitor assembly, reverse (3 EACH SIDE) this procedure. STRAGGT Oe, mo Q Be sure to check the clearance of the "L” brackets BEFORE setting the monitor into the table top. O After replacing the T.V. monitor, be sure to run the game in Self-Test.

~ REMOVE 4 SCREWS (2 EACH SIDE)

Figure 2-18 Removing the Monitor - Cocktail

2-21

Page 31

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT 2.8.1 Upright Models 2.8.2 Mini Models

2.8.3 Cocktail Models

2-22

Page 32

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT UPRIGHT

2.8.1 UPRIGHT MODEL: (See Figure 2-19) QO Turn the power to the game off.

O Unlock and open the rear access door (game board) and the coin door (sound board).

Q Disconnect the game board from all its cabling. 0 Disconnect the sound board from allits cabling. O Remove the indicated P.C.B. supports and lift the above P.C.B.'s out of the cabinet. Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 2-19, and slide it out the back of the cabinet. Q To reinstall the above P.C.B.'s, reverse this procedure.

NOTE: P.C.B.'s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connect itto the P.C.B.’s are also keyed and will ONLY go onto their connectors one way without forcing them.

REMOVE REMOVE SUPPORT SUPPORT TO TO SLIDE SLIDE POWER GAME SUPPLY BOARD BOARD OUT OUT

Figure 2-19 Removing P.C.B.’s - Upright

2-23

Page 33

2.8 PRINTED CIRCUIT BOARD (P.C.B) REPLACEMENT (Cont'd) UPRIGHT

NOTE: P.C.B.’s are all keyed and will ONLY fit into their connectors one way without forcing them. The plugs on the cable harness which connect itto the P.C.B.'s are also keyed and will ONLY go onto their connectors one way without forcing them.

2.8.1 UPRIGHT MODEL: (See Figure 2-21) (Cont'd) QO Turn the power to the game off.

O Unlock and open the coin door.

O Reach inside and release the game’s front access door locking latches. See Figure 2-20 and the drawing on top of the coin box lid. O Slide out the utility shelf. See Figure 2-21. O Mounted on the utility shelf is the commercial card rack with six cards in it. 1 Mounted next to the commercial card rack is its power supply P.C.B. O To remove the cards from the commercial card rack, simply lift on their extractors and remove them.

NOTE: BEFORE removing the "GAME PCB", be sure to disconnect it fram all its cabling. O To remove the power supply PCB for the commercial card rack. See Figure 2-21.

Disconnect it from all its cabling, remove the screws which secure the top PCB support to its mounting bracket (be careful not to lose the washers), and lift it out. To reinstall the above P.C.B.’s, reverse this procedure.

  • ACCESS. com sox coven acess

OO ©

COIN DOOR FOR SERVICE ACCESS OPEN LOWER SERVICE DOOR BY RELEASING TWO ACCESS CLAMPS. (Locations as SHOWN) . REMOVE TWO RED SHIPPING BRACKETS AND SLIDE OUT SERVICE SHELF. osr-ceee-0008

Upright

REMOVE THIS BRACKET TO TAKE OUT POWER SUPPLY BOARD

LIFT UP ON EXTRACTORS TO REMOVE CARDS FROM CARD BACK

Figure 2-21 Removing Printed Circuit Boards - Upright

2-24

Page 34

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT (Cont'd) MINI

2.8.2 MINI MODEL: (See Figure 2-22) O Turn the power off to the game.

Unlock and open the rear access door.

Disconnect the game board from all its cabling. Disconnect the sound board from allits cabling. Remove the indicated P.C.B. supports and lift the above P.C.B.’s out of the cabinet. Disconnect the power supply board from its cabling, remove the P.C.B. supports indicated in Figure 2-22 and slide it out the back of the cabinet. O To reinstall the above P.C.B.'s, reverse this procedure. oooa

o

REMOVE P.C.B. LIFT UP ON SUPPORT AND EXTRACTORS TO SLIDE BOARD REMOVE CARDS OUT FROM BACK

Figure 2-22 Removing P.C.B.'s - Mini

2-25

Page 35

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT (Cont'd) MINI

2.8.2 MINI MODEL: (See Figure 2-23) (Cont'd) O Turn the power off to the game.

O Unlock and open the rear access door.

O Disconnect the “GAME PCB” from all its cabling. O To remove any of the PCB's from the commercial card rack, just lift up on their extractors and slide them up and out. They may now be removed from the cabinet. O Disconnect the power supply board from all its cabling, remove the P.C.B. supports indicated in Figure 2-23, and slide it out the back of the cabinet.

Q To reinstall the above P.C.B.’s reverse this procedure.

REMOVE P.C.B, LIFT UP ON SUPPORT AND EXTRACTORS TO SLIDE BOARD OUT REMOVE CARDS FROM BACK

Figure 2-23 Removing Printed Circuit Boards - Mini

2-26

Page 36

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT (Cont'd) COCKTAIL

2.8.3 COCKTAIL TABLE MODEL: (See Figure 0 To remove the power supply board. See Figure 2-24) 2-24. | Turn the power off to the game. Disconnect it from all its cabling. O Open the cabinet. Remove the two smallest P.C.B. supports. Open the coin box door and release the two Once these are removed, the power supply can latches indicated in Figure 2-17. be lifted out the top of the cabinet. , To reinstall the power supply board, reverse this

WARNING: The right hand latch is very close to procedure. the HIGH VOLTAGE on the monitor. | O To remove the game and sound boards. See 5 Figure 2-24. ion piiee released, unhook them from their Disconnect the game board from all its cabling. Disconnect the sound board from allits cabling. O Grasp the table top at "A” and open it as bling indicated in Figure 2-17. ae i O Remove the indicated P.C.B. supports and lift
CAUTION: Due to the weight of the moni the above P.C.B.’s out of the cabinet. EXTREME CARE MUST be taken when opening To reinstall the game and sound boards, reverse the cabinet. this procedure.

REMOVE SUPPORT Se. ee 1 REMOVE SUPPORT TO SLIDE GAME /; ; or : | TO SLIDE POWER BOARD OUT . Be ; : /MB SUPPLY BOARD FROM a, a CABINET

Figure 2-24 Removing P.C.B’s - Cocktail ©

2-27

Page 37

2.8 PRINTED CIRCUIT BOARD (P.C.B.) REPLACEMENT (Cont'd)

2.8.3 COCKTAIL TABLE MODEL: (See Figure 2-25) (Cont'd)

Turn the power off to the game. Open the cabinet: Open the coin box door and release the two latches indicated in Figure 2-17.

WARNING: The right hand latch is very close to the HIGH VOLTAGE on the monitor. BE CAREFUL!!

Once they’re released, unhook them from their latch plates. Grasp the table top at "A" and open it as indicated in Figure 2-17.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

LIFT UP ON EXTRACTORS TO REMOVE CARDS FROM RACK o COCKTAIL

To remove the power supply board. See Figure 2-25. Disconnect it from all its cabling. Remove the two smallest P.C.8. supports. Once these are removed, the power supply can be lifted out the top of the cabinet. To reinstall the power supply board, reverse this procedure.

To remove the PCB's from the commercial card rack, See Figure 2-25. Disconnect the "GAME PCB” from all its cabling. To remove any of the PCB’s from the commercial card rack, just lift up on their extractors and slide them up and out. They may now be removed from the cabinet.

To reinstall these PCB's, reverse this procedure.

REMOVE P.C.B. SUPPORT LOCATED ON THIS SIDE AND SLIDE BOARD UP

Figure 2-25 Removing Printed Circuit Boards - Cocktail

2-28

Page 38

2.9 OPENING THE UPPER ATTRACTION PANEL 2.9.1 Upright Models 2.9.2 Mini Models (THE COCKTAIL MODEL HAS NO BACK—LIT ATTRAC—

TION PANEL)

2-29

Page 39

2.9 OPENING THE ATTRACTION PANEL UPRIGHT

2.9.1 UPRIGHT MODEL: (See Figure 2-26) Oo

a Turn the power to the game off. Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 2-26. Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. To reinstall the attraction panel, reverse this procedure.

2-30 REMOVE TOP BRKT. & SLIDE HEADER UP

Figure 2-26 Opening the Attraction Panel - Upright

Page 40

2.9 OPENING THE ATTRACTION PANEL (Cont'd) UPRIGHT

2.9.1 UPRIGHT MODEL: (See Figure 2-27) (Cont'd) 1 Turn the power to the game off.

OC Opening the attraction panel: Remove the screws which secure the bottom bracket in place. (They are on its bottom side.) See Figure 2-27. Remove the lower bracket and slide down the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. Q To reinstall the attraction panel, reverse this procedure.

SLIDE ATTRACTION REMOVE BOTTOM PANEL DOWN BRACKET

Figure 2-27 Opening the Attraction Panel

  • Upright

2-31

Page 41

2.9 OPENING THE ATTRACTION PANEL (Cont'd) UPRIGHT

2.9.1 UPRIGHT MODEL: (See Figure 2-28) (Cont'd) oO . REMOVE TOP SLIDE ATTRACTION Turn the power to the game off. BRACKET PANEL UP OD Opening the attraction panel: Remove the screws which secure the top bracket in place. (They are on its top side.) See Figure 2-28. Remove the top bracket and slide up the attraction panel. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. O To reinstall the attraction panel, reverse this procedure.

Figure 2-28 Opening the Attraction Panel

  • Upright

2-32

Page 42

2.9 OPENING THE ATTRACTION PANEL (Cont'd) MINI

2.9.2 MINI MODEL: (See Figure 2-29) O Tum the power off to the game. REMOVE TOP BRKT. & SLIDE HEADER UP O Remove the screws which secure the top bracket in place. (They are on its top side.) O Remove the top bracket and slide up the attraction panel. This exposes the attraction panel light bulbs and their mounting board. O To reinstall the attraction panel, reverse this procedure.

Figure 2-29 Opening the Attraction Panel - Min!

2-33

Page 43

2.9 OPENING THE ATTRACTION PANEL MINI

2.9.2 MINI MODEL: (See Figure 2-30) (Cont'd) OQ Turn the power off to the game. O Remove the screws from the top and bottom of the formed attraction panel. 0 Remove the formed attraction panel by pulling it straight away from the cabinet. This exposes the attraction panel light bulbs and their mounting board. QO To reinstall the attraction panel, reverse this procedure.

Figure 2-30 Removing the Attraction Panel - Mini

2-34

Page 44

REPLACING THE GAMES UPPER ATTRACTION PANEL LIGHTING

2.10.1 Upright Models 2.10.2 Mini Models (THE COCKTAIL MODELS HAVE NO BACK-LIT

ATTRACTION PANEL)

2-35

Page 45

2.10 SERVICING ATTRACTION PANEL LIGHTING UPRIGHT

2.10.1. UPRIGHT MODEL: QO Turn the power to the game off. REMOVE SCREWS TO LIGHT BRKT.

NOTE: In order to do this, the attraction panel MUST be removed first. See "Upright Model” procedure.

1 The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.

WARNING: ff you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

OC Replacing the fluorescent light tube starter, See Figure 2-31. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket.

x ‘ing Fi nt O To replace the fluorescent light tube starter, Figure 2-32 Replacing Fluorescent Light Mounting reverse this procedure. Bracket - Upright Remove the screws which secure it and gently QO Replacement of the fluorescent tube mounting Slide it out the front of the cabinet, being careful bracket assembly. See Figure 2-32. not to catch its power cable on anything. Be sure the power is off to the game. O To reinstall the fluorescent tube mounting Disconnect it from its power cable. bracket assembly, reverse this procedure.

1/4 TURN FLUORESCENT TUBE TO REPLACE STARTER

Figure 2-31 Replacing Fluorescent Tube Starter

2-36

Page 46

2.10 SERVICING ATTRACTION PANEL LIGHTING (Cont'd) UPRIGHT

2.10.1 UPRIGHT MODEL: (Cont'd) Turn the power to the game off.

NOTE: !n order to do this, the attraction panel MUST be removed first. See “Upright Model” procedure. O The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.
WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

C1 Replacing the fluorescent light tube starter. See Figure 2-34. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. QC To replace the fluorescent light tube starter, reverse this procedure. O The ultraviolet light tube may be replaced at this time by removing the rear access door of the game and the back scenery panel if necessary. See Figure 2-35. BE CAREFUL NOT TO DROP IT.

WARNING: If you drop an ultraviolet light tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion, Use care when replacing any ultraviolet tube.

QO Replacing the ultraviolet light tube starter. See Figure 2-34. Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. OG To replace the ultraviolet light tube starter, reverse this procedure. O Removing the light board assembly: See Figure 2-33 The attraction panel, the rear access door of the game, and, ifnecessary, the back scenery panel MUST be removed first. This will enable you to reach all the necessary areas where cables MUST be disconnected.

2-37 Disconnect the light board assembly from all its cabling. There is one plug at the upper right and upper left corners of the rear of the cabinet. There is also a small plug right at the ON/OFF switch. And DO NOT FORGET TO DISCON— NECT THE GROUND WIRE LUG FROM THE ON/OFF SWITCH! Remove the screws which secure the light board assembly to the cabinet. The light board assembly is now free and can be slid out through the hole in the front of the game where the attraction panel was mounted. O To reinstall the light board assembly, reverse this procedure. O Replacement of the fluorescent and ultraviolet tube mounting bracket assemblies. Disconnect it from its power cable. Remove the screws which secure them to the speaker board assembly. QO To reinstall the fluorescent ultraviolet tube mounting bracket assemblies, reverse this procedure.

SPEAKER BOARD

Figure 2-33 Servicing Attraction Panel Lighting

  • Upright
Page 47

UPRIGHT 2.10 SERVICING ATTRACTION PANEL LIGHTING (Cont'd)

FLUORESCE! TUBE START! we oO < at a wi ° F Y TURN

Figure 2-34 Replacing Fluorescent Tube Starter

Ww c Ww wt or co} cs) Ef oe $a aoc

Figure 2-35 Replacing Black Light

2-38

Page 48

2.10 SERVICING ATTRACTION PANEL LIGHTING (Cont'd) MINI

2.10.2 MINI MODEL: (See Figure 2-36) O Turn the power off to the game. MOUNTING BOARD

NOTE: In order to do this, the attraction panel MUST be removed first. See "Mini Model” Procedure. G To service the light bulbs and their mounting board:

Turn the power to the game back on so you can see which bulbs are burnt out.,

Mark the burnt out bulbs and turn the power to the game back off again. To replace the burnt out bulbs, grasp them gently and pull straight out. The new bulbs are gently pushed into the empty sockets. O To completely replace the light bulb mounting board: Open the cabinet rear access door and unplug the mounting board from its power cable. Remove the screws that hold the mounting board to the cabinet. Gently slide the mounting board out the front of the cabinet being careful not to catch its cable on anything. Figure 2-36 Servicing Attraction Pane! Lighting

O To reinstall the above removed items, reverse this procedure.

2-39

Page 49

SPEAKER REPLACEMENT

2.11.1 Upright Models 2.11.2 Mini Models 2.11.3 Cocktail Models

2-40

Page 50

2.141 SPEAKER REPLACEMENT UPRIGHT

2.11.1. UPRIGHT MODEL: (See Figure 2-37) O Turn the power to the game off. REMOVE SCREWS TO

NOTE: In order to do this, the attraction panel LIGHT BRKT. and fluorescent light fixture MUST be removed first. See “Upright Model” procedure.

O Replacing the speaker. Be sure the power is off to the game. Remove the attraction panel and disconnect the speaker from its cabling. Remove the nuts and bolts which secure the speaker and speaker grill in place and set them REMOVE SPEAKER and the speaker grill aside. FROM FRONT OF Once the bolts which secure the speaker in GAME place are removed, the speaker may be removed through the opening where the attraction panel was. CG Reverse this procedure to reinstall the speaker.

Figure 2-37 Speaker Replacement

2-41

Page 51

2.11 SPEAKER REPLACEMENT (Cont'd) UPRIGHT

2.11.1 UPRIGHT MODEL: (See Figure 2-38) (Cont'd)

NOTE: !n order to do this, the attraction panel MUST be removed first. See "Upright Model” Procedure.

O Replacing the speaker. O Be sure the power is off to the game.

Remove the attraction panel and disconnect the speaker from its cabling. ‘Remove the nuts and bolts which secure the speaker and speaker grill in place and set them and the speaker grill aside. Once the bolts which secure the speaker in place are removed, the speaker may be removed through the opening where the attraction panel was. 0 Reverse this procedure to reinstall the speaker.

MOUNTING

HARDWARE SPEAKER GRILL

Figure 2-38 Speaker Replacement

2-42

Page 52

2.11. SPEAKER REPLACEMENT (Cont'd) UPRIGHT

2.11.1 UPRIGHT MODEL: (Cont'd) O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. O To reinstall the speaker, simply reverse this procedure. MOUNTING HARDWARE

SPEAKER MOUNTING SPEAKER GRILL HARDWARE

ica

Figure 2-39 Speaker Location - Upright

Figure 2-40 Rear View - Speaker Location - Upright

2-43

Page 53

2.11. SPEAKER REPLACEMENT (Cont'd) UPRIGHT

2.11.1 UPRIGHT MODEL: (Cont'd) C Turn the power to the game off.

NOTE: In order to do this, the attraction panel MUST be removed first. See "Upright Model” procedure.

O Removing the speaker board assembly: The attraction panel, the rear access door of the game, and if necessary, the back scenery panel MUST be removed first. This will enable you to reach all the necessary areas where cables MUST be disconnected. Disconnect the speaker board assembly from all its cabling. There is one plug at the upper right and upper left corners of the rear of the cabinet. There is also a small plug right at the ON/OFF switch. And DO NOT FORGET TO DISCON- NECT THE GROUND WIRE LUG FROM THE ON/OFF SWITCH!

SPEAKER BOARD

Figure 2-41 Speaker Replacement - Upright

2-44 o Remove the screws which secure the speaker board assembly to the cabinet. The speaker board assembly is now free and can be slid out through the hole in the front of the game where the attraction panel was mounted.

Replacing the speaker(s). Disconnect the speaker(s) from its cabling. Remove the nuts and bolts which secure the speaker in place and set them aside. Once the bolts which secure the speaker(s) in place are removed, the speaker(s) may be removed from the speaker board assembly. Reverse this procedure to speaker(s). reinstall the

To reinstall the speaker board assembly, reverse this procedure.

MOUNTING HARDWARE

SPEAKER

Figure 2-42 Speaker Replacement - Upright

Page 54

2.11. SPEAKER REPLACEMENT (Cont'd) MINI

2.11.2 MINI MODEL: (See Figure 2-43) REMOVE Q To replace the speaker. SPEAKER FROM REAR Be sure the power is off to the game. OF GAME Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Slide the speaker out through the rear access door. QC To reinstall the speaker, simply reverse this procedure.

i

Figure 2-43 Speaker Removal - Mini

2-45

Page 55

2.11. SPEAKER REPLACEMENT (Cont'd) COCKTAIL

Figure 2-44 Opening the Cocktail Game

2.11.3 COCKTAIL TABLE MODEL:

1 Turn power to the game off. © Open the coin box door and release the two latches indicated in Figure 2-44,

WARNING the HIGH V he right hand latch is very close to TAGE on the monitor.

Once they're released, unhook them from their latch plates. O Grasp the table top at "A” and open it as indicated in Figure 2-44.

CAUTION: Due to the weight of the monitor, EXTREME CARE MUST be taken when opening the cabinet.

O To replace the speaker. Be sure the power is off to the game. Disconnect the speaker from its cabling. Remove the nuts and bolts securing the speaker. Lift the speaker out. SPEAKERS O To reinstall ‘the speaker, simply reverse this —

procedure. Figure 2-45 Speaker Replacement - Cocktail

Page 56

2.12 OPENING THE LOWER ATTRACTION PANEL AND

SERVICING IT’S LIGHTING ASSEMBLY

2.12.1 Upright Models (THE MINI AND COCKTAIL MODELS HAVE NO BACK-

LIT LOWER ATTRACTION PANELS)

2-47

Page 57

2.12 OPENING THE LOWER ATTRACTION PANEL AND SERVICING ITS LIGHTING ASSEMBLY UPRIGHT

2.12.1 UPRIGHT MODEL ONLY O Be sure the power is off to the game. O Remove the control panel as described previously. This exposes the attraction panel fluorescent light tube and its mounting bracket assembly. See Figure 2-46. The fluorescent light tube may be replaced at this time by reaching through the space where the control panel was before you removed it.

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

O Replacing the fluorescent tube starter. See Figure 2-47. Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. O Replacement of the fluorescent tube mounting bracket assembly. See Figure 2-46.

a™ 1/4 TURN TO REPLACE O Be sure the power is off to the game.

O Disconnect it from its power cable.

NOTE: The fluorescent tube mounting bracket is an integral part of the center attraction panel assembly and cannot be replaced unless the center attraction panel assembly is removed from the game cabinet.

O Remove the screws from top support bracket and the screws along its base which secure the mounting bracket and the center attraction panel assembly to the cabinet as shown in Figure 2-46. 0 Thecenter attraction paneiassembly is now free and can be rotated forward and lifted out of the cabinet. O The screws which secure the fluorescent tube mounting bracket to the center attraction panel are now accessible so it can be separated from the center attraction panel and replaced. O To reinstall any of the above removed items, reverse this procedure.

FLUORESCENT LIGHT TUBE

REMOVE SCREWS TO TAKE CENTER ATTRACTION PANEL FROM GAME

FLUORESCENT TUBE STARTER

Figure 2-47 Replacing the Fluorescent Tube Starter - Upright

2-48

Page 58

2.13 SERVICING THE CONTROL PANEL LIGHTING

ASSEMBLY

2.13.1 Upright Models (THE MINI AND COCKTAIL MODELS HAVE NO

CONTROL PANEL LIGHTING ASSEMBLIES)

Page 59

2.13 SERVICING THE CONTROL PANEL LIGHTING ASSEMBLY UPRIGHT

2.13.1 UPRIGHT MODEL ONLY Be sure the power is off to the game. O Remove the control panel as described pre- QO Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket.

viously. This exposes the bottom row of screws which secure the control panel support bracket and the black light protector in place. See Figure 2-48. Remove ail the screws which secure the above items in place and set them aside. The black light tube may be replaced at this time by reaching through the space where the light protector was before you removed. it.

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

Replacing the black light tube starter. See Figure 2-47. Remove the black light tube. Remove the screws which secure the black light tube mounting bracket to the cabinet. See Figure 2-49. The mounting bracket is now loose and can be pulled out and slightly to one side until you can see the black light tube starter.

REMOVE THESE SCREWS To replace the black light tube starter, reverse this procedure. O The black light tube mounting bracket assembly may be replaced at this time by simply disconnecting it from its power cable and removing it from the game. To reinstall any of the above mentioned items, simply reverse this procedure.

Figure 2-49 Replacing the Fluorescent Tube Starter - Upright

" BLACK LIGHT PROTECTOR

CONTROL PANEL SUPPORT BRKT.

Figure 2-48 Servicing Control Panel Lighting Assembly - Upright

2-50

Page 60

2.13 SERVICING THE CONTROL PANEL LIGHTING ASSEMBLY UPRIGHT

“~~

1/4 TURN FLUORESCENT TUBE TO REPLACE STARTER

Figure 2-50 Replacing the Fluorescent Tube Starter - Upright

2-51

Page 61

SERVICING AUXILIARY LIGHTING

2.14.1 Upright Models - Servicing Windshield Fluorescent Light 2.14.2 Upright Models - Servicing The Black Light Above Control Console 2.14.3 Upright Models - Servicing The Fluorescent Light Behind The Front Service Panel

2-52

Page 62

2.14 SERVICING AUXILIARY LIGHTING UPRIGHT

2.14.1 UPRIGHT MODEL: Servicing Windshield Fluorescent Light

O Be sure the power is off to the game.

O Remove the upper rear access door. This exposes the windshield fluorescent light tube mounting bracket assembly. See Figure 2-51. ) Replacing the fluorescent tube starter. See Figure 2-51, Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. To replace the fluorescent light tube starter, reverse this procedure. Q Removal of the fluorescent tube mounting bracket assembly from the cabinet. Be sure the power is off to the game. Disconnect it from its power cable.

FLUORESCENT LIGHT TUBE MTG. BRKT.

STARTER Remove the screws along its base which secure the mounting bracket to the inside of the cabinet as shown in Figure 2-51. Remove the two end screws first and the center one last. The fluorescent tube mounting bracket assembly is now free and can be removed from the cabinet. O The fluorescent light tube may be easily replaced at this time.

WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

O To reinstall any of the above removed items, reverse this procedure.

REMOVE (3) SCREWS

Figure 2-51 Servicing Windshield Fluorescent Light - Upright

2-53

Page 63

2.14 SERVICING AUXILIARY LIGHTING (Cont'd) UPRIGHT

2.14.2 UPRIGHT MODEL: Servicing The Black Light Above Control Console

1 Turn the power to the game off and remove the screws which secure the glass clamping plate in position. See Figure 2-52. Lift out the glass clamping plate. Remove the screws which secure the bottom of the black light shield to the front service panel. Be sure you support the black light shield as you remove these screws so it will not fail on the floor. The black light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT.

WARNING: If you drop a black light tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any black light tube.

DO To reinstall the black light shield, reverse this procedure. Q Replacing the black light tube starter. See Figure 2-53.

NOTE: The main-display-glass MUST be removed in order to do this. See “Upright Model” procedure. Figure 2-52 Removing Glass Clamping Plate

Q Be sure the power to the game has been turned off. Grasp the starter (it is on the back of the mounting bracket, just inside the frame for the maindisplay-glass), give ita quarter turn, and remove it from its socket.

O To replace the black light tube starter, reverse this procedure.

aN

1/4 TURN TO REPLACE FLUORESCENT TUBE STARTER

Figure 2-53 Replacing the Fluorescent Tube Starter - Upright

2-54

Page 64

2.14 SERVICING AUXILIARY LIGHTING (Cont'd) UPRIGHT

2.14.13 UPRIGHT MODEL: Servicing The Fluorescent Light Behind The Front Service Panel

O Remove the front service panel.

O Turn the power to the game off.

NOTE: In order to do this, the following items MUST be removed first, in this ‘order, to make room: 1) the main-display-glass glass clamping plate; 2) the black light shield; and 3) the control panel. See the appropriate sections of this manual for removal instructions. Remove the screws at the top of the front service panel which secure it to the cabinet. O Tilt it back to clear the black light and lift it up and out as shown in Figure 2-54. To reinstall the front service panel, reverse this procedure. QO The fluorescent light tube may be replaced at this time. BE CAREFUL NOT TO DROP IT!
WARNING: If you drop a fluorescent tube and it breaks, IT WILL IMPLODE! Shattered glass can fly six (6) feet or more from the implosion. Use care when replacing any fluorescent tube.

O Replacing the fluorescent light tube starter. See Figure 2-55. Be sure the power to the game has been turned off.

1/4 TURN TO REPLACE SHIELD

FRONT SERVICE PANEL

Figure 2-54 Removing the Front Service Panel

  • Upright

QO Grasp the starter (it is on the back of the mounting bracket), give it a quarter turn, and remove it from its socket. QO To replace the fluorescent light tube starter, reverse this procedure.

FLUORESCENT TUBE STARTER

Figure 2-55 Replacing the Fluorescent Tube Starter - Upright

2-55

Page 65

Il. Technical Troubleshooting

Introduction

The most common problems occur in harness components such as the coin acceptor, player controls, interconnecting wiring, etc. The TV monitor and PCB computer cause their share of problems too, but not as much as the harness and its component parts. TV monitor troubleshooting will not be covered here because it is covered in that section of this manual. As you already know, the PCB computer is a complex device with a number of different circuits. Some circuits remain basically the same among games, but overall there are a great many differences between them. PCB troubleshooting procedures, therefore, can be lengthy and will differ greatly among games. However, some basic Z-80 CPU information is involved in this section.

General Suggestions

The first step in any troubleshooting procedure is correctly identifying the malfunction’s symptoms. This includes not only the circuits or features malfunctioning, but also those still operational. A carefully trained eye will pick up other clues as well. For instance, a game in which the computer functions fail completely just after money was collected may have a quarter shorting the PCB traces. Often, an experienced troubleshooter will be able to spot the cause of the problem even before opening the cabinet. After all the clues are carefully considered, the possible malfunctioning areas can be narrowed down to one or two good suspects. Those areas can be examined by a process of elimination until the cause of the malfunction is discovered.

Harness Component Troubleshooting

Typical problems falling in this category are coin and credit problems, power problems and failure of individual features. NO GAME CREDIT For example, your prospective player inserts his quarter and is not awarded a game. The first item to check is if the quarter is returned. If the quarter is returned, the malfunction most certainly lies in the coin acceptor itself. First, use a set of test coins (both old and new) to ascertain that the player’s coin is not undersize or underweight. If your test coins are also returned, coin acceptor servicing is indicated. Generally, the cause of this particular problem is a maladjusted magnet gate. Normally, this will mean slightly closing the magnet gate alittle by turning the adjusting screw out a bit (see section on coin acceptor for more details). \f the quarter is not returned and there is no game credit, the cause of the malfunction may be in one of several areas. First try operating the coin return button; if the coin is returned, the problem is most likely in the magnet gate. Enlarge the gap according to the coin acceptor service procedures. If this does not cure the problem, remove the coin acceptor, clean it and perform the major adjustment procedure. lf the trapped coin is not returned when the wiper lever is actuated, you may have an acceptor jammed by a slug, gummed up with beer, a jammed coin chute, or mechanical failure of the acceptor mechanism. In this case, first check for the slug that will generally be trapped against the magnet. If so, simply remove the slug and test the acceptor. If the chute is blocked, remove the acceptor and remove the jammed coins. If there is actual failure of the acceptor, remove the unit and repair as indicated in the coin acceptor service procedures. If the coin is making its way through the acceptor (that is, falling into the coin box), yet there is still no game credit, you either have a mechanical failure of the coin switch or electrical failure of the coin and credit circuits. The first place to begin is by checking the coin switch. Most of these switches are the make/break variety of micro switch, which is checked by testing for continuity between the NO, NC, and C terminals. When not actuated, the NC and C terminals should be continuous and the NO terminal open. When operated, the NO and C terminals should close and the NC should be open. If the coin switch checks out, examine the connections to the terminals to make sure there is good contact. If necessary, use the continuity tester and check from the terminal lug on the switch to the assocjated PCB trace. This will tell you if there is a continuous line all the way to the credit circuit.

Page 66

If the coin switch wires do not check out, the problem is in the computer — most likely in the coin and credit circuitry. If you do get game credit when a coin is deposited, but the game will not start when the start switch is pressed, you may have a problem in the start switch, the interconnecting wiring or in the computer. First check the switch. If the switch is OK, proceed to check the wiring. Again, make sure you go from the terminal lug on the switch to the PCB trace. This way, you will check the terminal contact as well as PCB edge connector contact. If the wiring is continuous, proceed to check the PCB credit circuit. If noi, check each section of the wiring, until the discontinuity is located. If the wiring is OK, the problem must lie in the computer.

Transformer and Line Voltage Problems

Your machine must have the correct line voltage to operate properly. If the line voltage drops too low, a circuit in the computer will disable game credit. The point at which the computer will fail to work will vary some from game to game, but no game will work on line voltage that drops below 105 VAC. Low line voltage may have many causes. Line voitage normally fluctuates a certain amount during the day as the total usage varies. Peak usage times occur mainly at dawn or dusk, so if your machine's malfunction seems to be related to the time of day, this may be a factor. A large load connected to the same line as the game (such as a large air conditioner or other device with an exceptionally large motor) may drop the line voltage significantly when starting up. This drop can result in an intermittent credit problem. In addition, poor connections in the location wiring, plug, or line cord may also cause a signiticant drop in power. Cold solder joints in the game’s harness, especially in areas like the transformer connections, interlock switch, or fuse block, may also produce the same results, although probably on a more permanent basis. Sometimes location owners (especially in bars) replace light switches with dimmer rheostats, and the game is sometimes on the same line. Obviously, the voltage available to the game is going to drop dramatically when the dimmer is turned. \n any case, the way to check for correct line voltage is with your VOM. Set the VOM to 250 VAC and stick the probes in the wall receptacle. If it's OK here, check the transformer primary connections. If you do not get 117 VAC, examine the solder joints on the transformer, fuse block, and interlock switch. If you do get 117 VAC, the problem must be either in the transformer, harness connections, or in the PCB power supply. If you suspect the transformer, check its secondaries with the VOM set to 50 VAC and correlate the readings with the legend on the side of the transformer. The transformer must also be correctly grounded, so check the ground potential as well, especially if there is a hum bar rolling up or down the TV screen.

HARNESS PROBLEMS Other harness problems include blowing fuses and malfunctioning controls. The repeating blown-fuse problem can sometimes be quite exasperating to solve, for short circuits have the tendency to occur in areas almost impossible to find. First, try inserting a new fuse, as old fuses age and blow without cause. If the new one also blows, you definitely have a short. The best way to approach this problem is by turning the power off and disconnecting devices that may be causing the problem, such as the TV, transformer, and PCB. Disconnect the devices by pulling off their connectors, but do not allow them to touch. If necessary, insulate them with small pieces of electrical tape. Then, connect your VOM across the terminals of the fuse block (all electrical power shut off), and set it to one of the resistance scales. This will save blowing a fuse each time you want to check the circuit. If the VOM reveals that disconnecting the devices removed the short, reconnect the devices one by one until the short returns. The last device connected is the one that is at fault. If the VOM reads a short even after the devices are disconnected, the fault must lie in the harness itself, and only patient exploration will reveal its location. First, carefully examine all the wiring, looking for terminals that may be touching, metal objects such as coins shorting connections or burned insulation. If necessary, use the VOM to check each suspected wire. MALFUNCTIONING CONTROLS One of the most common problems here is a bad potentiometer. Typically, a bad pot will cause the image to jump as it reaches a certain point. The only cure for this one is to install a new pot. If a feature that is operated by a switch (for example, joysticks, foot pedals, contro! pane! buttons) does not operate at all, check the switch with a VOM or continuity tester to verity its operation. If the switch does not check out, replace it. If the switch is OK, you should suspect the input to the switch from the PCB. In this case, get out the harness and logic schematics and check to see what kind of input it is. in many cases, the inputwill be +5 VDC. liso, use the VOM to check its presence. Normally, the switch is used to pull a +5 VDC line LOW to GND or to pulla LOW line HIGH. If the PCB output is missing, check the wire length from the PCB. It you findthe signal at the PCB trace, the wire !ength or connection is at fault. If not, begin exploring the PCB using the logic schematics.

Page 67

A Glossary of Microprocessor Terms

MICROPROCESSOR — one or several microcircuits that perform the function of a computer's CPU. Sections of the circuit have arithmetic and comparative functions that perform computations and executive instructions.

CPU — central-processing unit. A computing system's “brain”, whose arithmetic, control and logic elements direct functions and perform computations. The microprocessor section of a microcomputer is on one chip or several chips. PROM — programmable read-only memory. User permanently sets binary on-off bits in each cell by selectively fusing or not fusing electrical links. Nonerasable. Used for low-volume applications.

EPROM — erasable, programmable, read-only memory. Can be erased by ultraviolet light bath, then reprogrammed. Frequently used during design and development to get programs debugged, then replaced by ROM for mass production.

ROM — read-only memory. The program, or binary on-off bit pattern, is set into ROM during manufacture, usually as part of the last metal layer put onto the chip. Nonerasable. Typical ROM's contain up to 16,000 bits of data to serve as the microprocessor's basic instructions. RAM — random-access memory. Stores binary bits as electrical charges in transistor memory cells. Can be read or modified through the CPU. Stores input instructions and results. Erased when power is turned off. LSI — large scale integration. Formation of hundreds or thousands of so-called gate circuits on semiconductor chips. Very large scale integration (VLS) involves microcircuits with the greatest component density. MOS — metal-oxide semiconductor. A layered construction technique for integrated circuits that achieves high component densities. Variations in MOS chip structures create circuits with speed and low-power requirements, or other advantages (static will damage a MOS chip).

Page 68

IV. Coin Door Maintenance

SPECIAL NOTE: If you have any questions about the coin acceptors in your game(s), please feel free to contact their manufacturers. Each manufacturer’s name is PROMINENTLY imprinted on every acceptor mechanism. Metal mechanisms only: COIN MECHANISMS, INC. 817 Industrial Drive Elmhurst, IL 60126 Phone (312) 279-9150

COIN DOOR MAINTENANCE

METAL COIN ACCEPTOR MECHANISMS

Periodically, the metal coin acceptor mechanism(s) must be removed from the coin door and cleaned.

  • Make sure the power to the game is off.
  • Unlock and open the coin door.

TO REMOVE PUSH LATCHES — DOWN

PLACE PEGS IN SLOTS TO REPLACE PULL MECHANISM OUT Metal and Plastic mechanisms: COINCO COIN ACCEPTORS, INC. 860 Eagle Drive Bensenville, IL 60106 Phone (312) 766-6781

  • Remove the coin acceptor mechanism as shown in Figure 4-1. Push down on the two spring loaded latches. O While holding the latches down, pull the top of the coin acceptor mechanism toward you. O Release the latches and lift out the coin acceptor mechanism.

PUSH MECHANISM IN

Figure 4-1 Removing & Replacing the Coin Acceptor

Page 69
  • Clean the magnet of all foreign particles. See Figure 4-2. O This may be accomplished by swinging the gate open as shown in the above figure.
  • Remove the cradles and undersize levers and clean the bushings. (A pipe cleaner makes a good bushing cleaner.) D Also clean the pivot pin.
  • Whenever needed, the coin acceptor should be cleaned with hot water and cleanser in the following manner: Q Place the coin acceptor in boiling water for about ten minutes.

E CAREFUL NOT TO BURN YOUR-

O Next, use a brush and kitchen cleaner to remove all remaining foreign matter from the unit. O Rinse the coin acceptor in clean boiling water. Q Dry the coin acceptor thoroughly by using filtered compressed air to blow it dry.

NOTE: The reason we recommend using boiling water is that it evaporates faster than cold water and speeds drying time.

GATE OPEN AS SHOWN CLEAN MAGNET BY DRAGGING A SCREWDRIVER BLADE ACROSS SURFACE

Figure 4-2 Cleaning the Metal Coin Acceptor

  • To lubricate the coin acceptor: O Use ONLY powdered graphite and put it ONLY on the moving parts of the coin acceptor. These parts are called out in Figure 4-3. DO Be extremely careful to keep the powdered graphite away from paths that are traveled by the coins.
  • WARNING — DO NOT USE OIL TO LUBRICATE THE COIN ACCEPTOR.
  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 4-1. C Place the two pegs at the coin acceptor’s base into their retaining slots. O Now push the top of the coin acceptor toward the cain door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.

APPLY POWDERED GRAPHITE HERE

UNDERSIZE LEVER

“E” RINGS

CRAOLE

Figure 4-3 Lubricating the Metal Coin Acceptor

4-2

Page 70

SQUEEZE PINS TOGETHER TO UNLOCK SWING BOTH GATES OPEN

HOLDING BOTH GATES TOGETHER, PUSH UP AND PULL OUT

Figure 4-4 Opening the Plastic Coin Acceptor

PLASTIC COIN ACCEPTOR MECHANISMS The plastic coin acceptor mechanism(s) must be removed periodically from the coin door and cleaned,

  • Make sure the power to the game is off.
  • Unlock and open the coin door.
  • Remove the coin acceptor mechanisms(s) as shown in Figure 4-1. Push down on the two spring loaded tatches. O While holding the latches down, pull the top of the acceptor mechanism toward you. 0 Release the latches and lift out the mechanism. 4, Squeeze the two pins indicated in Figure 4-4 together tc open the mechanism and break it down into its three basic parts. 0 Clean the mechanism in hot soapy water. It never rusts. OC Rinse the mechanism in clean hot water and allow it to dry. Q Reassemble the mechanism (it never needs \ubrication).
  • Check the coin chute for obstructions such as: paper, gum, etc.
  • Reinstall the coin acceptor to the coin door. See Figure 4-5. O Place the two pegs at the coin acceptors base into their retaining siots. © Now push the top of the coin acceptor toward the coin door until it snaps in place and is held there by the two spring loaded latches.
  • Close and lock the coin door.
NOTE: See Figure 4-6 for insiructions on how to set the plastic coin acceptor mechanisms to either accept or reject Canadian quarters.

4-3

Page 71

ACCEPTOR CAN BE SET TO ACCEPT U.S. QUARTERS ONLY OR BOTH U.S. AND CANADIAN QUARTERS.

Oo

SLIDE MAGNET TO EXTREME RIGHT (AS SHOWN) TO ACCEPT BOTH U.S, AND CANADIAN QUARTERS.

TO ACCEPT U.S. QUARTERS ONLY, SLIDE MAGNET TO EXTREME LEFT.

Figure 4-5 Changing the Plastic Coin Acceptor to Accept American or Canadian Quarters

4-4

Page 72

V. T.V. Monitor Manual

PLEASE NOTE:

THE INFORMATION CONTAINED IN THIS SECTION IS TOLD IN AN EASY TO UNDERSTAND MANNER AND IS INTENDED TO AID THOSE WITHOUT AN ELECTRONICS DEGREE IN TROUBLESHOOTING AND REPAIRING THEIR GAMES T.V. MONITOR.

IF YOU READ THROUGH THIS SECTION AND STILL HAVE QUESTIONS, PLEASE CONTACT YOUR DISTRIBUTOR OR MIDWAY MANUFACTURING COMPANY AT THE TOLL FREE NUMBER PROVIDED WITH YOUR GAMES PAPERS.

OUR STAFF AND OUR DISTRIBUTORS STAND READY TO HELP YOU!

THANK YOU

Introduction: (How to

use this section of your manual.)

This section has been designed to simply familiarize you with one of the more mystical components in your game — the T.V. monitor. If you are an electronics technician who is quite knowledgeable on the subject, you may decide to just go to the schematics and start troubleshooting the defective monitor. But if you are like most people, a monitor is a T.V. set, and that means a complex doo-dad that means big buck repairs. This isn’t necessarily so. This section of the manual! will acquaint you with the monitor and could just help you repair it if you feel adventurous enough to give it a try. If you have any knowledge of electronics, especially the use of a voltmeter, the repairs you can make are astonishing. Just keep in mind that ELECTRICITY CAN BE VERY DANGEROUS, SO BE CAREFUL!!

If you want to understand how a monitor works, just read the "THEORY OF OPERATION” subsection. If you wish, you can foliow along with the schematics. The information is presented in a very basic manner but a more complete treatment of the subject can be found in the technical sections of bookstores.

|f you want to attempt to repair your monitor, it would be a good idea to read this whole section beginning to end before starting. Pay attention to all warnings and take them seriously. The more equipment you have the better, but alow cost Volt-Ohm-Milliameter can often do the trick. Here are the steps to take:

  • Find the symptom that matches the problems your monitor has in the “SYMPTOM — DIAG- NOSIS” subsection. The diagnosis tells the circuit or area the problem may be in and possibly even the actual component causing it.
  • Once you have the circuit that is causing the trouble, read the “TROUBLESHOOTING” subsection to learn the procedure for finding the bad part.
  • Next, go to the schematic section and find the schematic that matches your monitor. It may be helpful to read the “DIFFERENCES BETWEEN MONITORS” subsection if you are unsure of which monitor you have. Use the schematic to see what parts are in the offending circuit.

That really is all there is to it. Just remember that there are some bizarre or rare symptoms not covered, or that a monitor may have two or more different problems that only a genius, the experienced, or an experienced genius can figure out. But be patient, follow safety precautions, and remember that there is also literature available from the monitor companies through your distributor or from Bally Midway Manufacturing Company on request. (There is a toll free number on the back side of the front cover of this manual.)

Page 73

Symptom Diagnosis

  • Insufficient width or heighth: A. Horizontal line (due to VERTICAL CIR- CUIT DEFECT). O Bad yoke. Q Bad vertical output section. O Open fusible resistor in vertical section. U Bad height control. O Bad flyback. B. Vertical line (due to HORIZONTAL CIR- CUIT DEFECT). 0 Bad yoke. Open width coil. d Open part in horizontal output section.
  • Picture spread out too far or crushed in certain areas: A. Horizontal or vertical output transistor. 8B. Bad Component in output circuitry. C. Vertical linearity or damper control needs adjustment. Line too close with black spacing: A. Problem in vertical section causing poor linearity. Poor focus and convergence: A. Bad high voltage transformer (“flyback”) or control. B. Focus voltage wire not connected to neckboard terminal.
  • Colors missing; check: Intertace color transistors. Color output transistors. Cracked printed circuit board (neck Board). Color circuits. Video input jack. Defective picture tube.
  • Picture noi bright enough: A. Weak emission from picture tube.
  • Silvery effect in white areas; check: A. Beam current transistors. B. Weak picture tube emission.
  • Too much brightness with retrace lines; check: A. Beam limiter transistors. B. Brightness and/or color blanking contro! set too high.
  • Increasing brightness causes an increase in size and poor focus. A. Weak high voltage rectifier or regulation (high voltage unit). B. Bad component in monitor's power supply. 3.

™MOOM> 10.

nn.

12.

13.

14,

15.

16.

17.

18.

19.

20, Small picture and/or poor focus: A. Low B+ voltage (power supply trouble).

Vertical rolling: A. Vertical oscillator in the IC, vertical sync. transistor, or Circuit. B. No sync from logic board. G. Three pin sync. jack is loose or plugged in wrong. Horizontal line across center: A. Vertical output circuit is dead (see symptom No. 1. A,). B. Vertical oscillator is not putting out the right wave form.

Picture bends: A. Horizontal sync needs adjusting. B. Magnetic or electromagnetic interference. Flashing picture, visable retrace lines: A. Broken neck board. B. Internal short circuit in the picture tube (arcing). Unsymmeitrical picture or sides of picture: A. Defective yoke. No brightness, power supply operating — No high voltage for the picture tube; check: A. Horizontal oscillator. B. Horizontal amplifier and output. C. Flyback transformer (high voltage unit).

Ne ie nae high voltage present; check: Heater voltage to the tube at the neck board. B. Screen-grid voltage for the tube. CG. Focus voltage. D. Grid to cathode picture tube bias. No high voltage; check: For AC input to the “flyback”. Horizontal deflection stages. Flyback transformer. Yoke. Power supply. moom>r

No horizontal and vertical hold; check: A. Sync transistors and circuit. B. Wires and jack from logic board to the monitor. Wavey picture — (power supply defect); check: A. Transistors, diodes, electrolytic capacitors in the power supply.

Page 74
  • Moving bars in picture: A. Ground connector off between monitor and logic boards. B. Defect in the power supply (see wavy picture symptom).
  • Washed out picture (see picture not bright enough): A. Check video signal at the cathode pins with an oscilloscope. If there is about 80 volts peak to peak, the picture tube has weak emission.
  • Monitor won't turn on: A. Problem in the power supply: Check fuse, transistors, open fusible resistor.

B. Shorted horizontal output transistor. C. Defective high voltage disabling circuit. D. Crack(s) somewhere on main chassis board.

  • Can't adjust purity or convergence:

A. Use a degausser to demagnetize the picture tube carefully following your degausser’s instructions. B. Picture tube defective. C. Nearby equipment is electromagnetically interferring. D. The poles of the earth are pulling off the purity — see “A” above. E. Poor focus or width of picture. F. Make sure you have the correct CRT number for that brand of monitor.

Guide To Schematic Symbols

THERMISTOR (POLARITY DOESN'T MATTER)

SY W INDUCTOR, COIL, CHOKE (POLARITY DOESN'T MATTER)

(-) CATHODE

(+) ANODE

ZENER DIODE IRON CORE TRANSFORMER (SUCH AS A FLYBACK)

Ls

FUSE (POLARITY DOESN'T MATTER)

CATHODE (-)

ANODE (+)

DIODE

Page 75

COLLECTOR To COLLECTOR a BASE ———- BASE ——— EMITTER eed EMITTER “SY

NPN TRANSISTOR PNP TRANSISTOR

f wn

VARIABLE RESISTOR, POT, CONTROL RESISTOR (POLARITY DOESN'T MATTER) (POLARITY DOESN'T MATTER)

+ +

LINES ARE CONNECTED ELECTROLYTIC CAPACITOR

LINES ARE NOT CONNECTED CAPACITOR (POLARITY DOESN'T MATTER)

Tg

GROUND

5-4

Page 76

Troubleshooting

Troubleshooting monitors requires experience, patience, and luck. The first step is to match the symptom the monitor displays to the diagnosis next to it in the “SYMPTOM-DIAGNOSIS” subsection. This will pinpoint the circuit the problem is probably in, and often the parts to check. Next, the circuit shoud be visually inspected to see if there are any parts broken, burned, or if something is there that shouldn't be, like a loose screw, etc. Some parts go bad before others and should be checked first. In fact, following is the general order in which parts usually go bad:

  • Semiconductors (like transistors, diodes, and integrated circuits).
  • Fusible resistors.
  • Electrolytic capacitors.
  • Resistors.
  • Capacitors and coils. Always remember that a monitor can bite likea snake. Even when it is turned off, capacitors hold voltage and will discharge it to you should you be touching chassis ground. The picture tube or CRT, itself, is a giant capacitor, so avoid the flyback anode plug hole. With the monitor on, the power supply circuit and/or the flyback, which puts out at least 23,000 volts, CAN BE KILLERS! Avoid handling power transistors {usually output transistors) or ICs, yoke terminals, and other high power components when the monitor is on.
WARNING: That picture tube is a bomb! When it breaks, first it implodes, then it explodes. Large pieces of glass have been known to fly in excess of 20 feet in all directions. DO NOT carry it by the long, thin neck. Discharge its voltage to ground by shorting the anode hole to ground. Use a plastic handled screwdriver, connect one end of a wire with an alligator clip at each end to chassis ground and the other end to the metal shaft of the screwdriver. Using ONE HAND ONLY (put the other in your pocket) and touching ONLY the plastic handle of the screwdriver (DO NOT TOUCH THE METAL SHAFT) stick the blade of the screwdriver into the anode hole.
IMPORTANT! The side brackets of the monitor are chassis ground as is the aquadag, the picture tube’s dark conductive coating. BUT, on the ZENITH MONITOR there are metalic mounting parts which ARE NOT chassis ground. Discharging the CRT to these will damage the monitor!

5-5 Be prepared for a fairly loud pop and a flash. The longer the monitor has been turned off, the smaller the pop and dimmer the flash. But BE CARE- FUL, picture tubes will hold a very healthy charge for at least a week if not longer. Even after you've discharged it once, it may still carry a residual charge. It’s better to be too careful than dead, which is why electronic equipment always carries stickers referring servicing to qualified personnel. Handle the side with the viewing screen against your chest when changing it. ALWAYS wear safety goggles when handling the picture tube. To maintain the safety and performance of the monitor, always use exact replacement parts. For instance, the wrong components in the power supply can cause a fire, or the wrong color transistor may give a funny color to the picture. Service your monitor on a nonconduciive firm table like wood, NOT METAL, and take off ail of your jewelry just in case. With all this in mind, you are ready to begin troubleshooting.

Observe the picture carefully. Try to vary the appropriate control that would most likely affect your particular symptom. For example, if there is poor brightness or no picture, try turning up the brightness or contrast control. If the controls have no effect at all, chances are there is trouble with the controi itself, the circuit it controls, or a nearby circuit that may be upsetting voltages. Go to the list of symptoms and determine with the schematic where the bad circuit is.

CAUTION:

Keep in mind that capacitors hold a charge as can the picture tube (for at least a week and usually longer), and could shock you.

First, check for obvious visual defects such as broken or frayed wires, solder where it is not supposed to be, missing components, burned components, or cracked printed circuit boards. If everything looks good up to this point, make sure that diodes, electrolytic capacitors, and transistors have their leads connected in the right polarity as shown on the schematic and the circuit board. Turn on the power and measure the voltages at ihe leads of the active devices such as tubes, transistors, or integrated circuits. Any voltage that does not come within at least 10% to 15% of the voltage specified on the schematic indicates either a problem with that device or a component connected with it in the circuit. The next step is to use the onmmeter to narrow down the field of possible offenders.

Page 77

To test a transistor, one lead of the ohmmeter is placed on the base; and the other lead placed just on the emitter, then on the collector. A normal transistor will read either high resistance (infinite), or little resistance (400 to 900 ohms), depending on the polarity of this type transistor. Then the leads should be switched, one remaining On the base, and the other switched from the emitter to the collector. Now the opposite condition should result: the resistance should be infinite if it was lower when the other lead was on the base. Consistantly infinite readings indicate an open, and a short is demonstrated by 0-30 ohms on most of these test readings. Finally, place one lead on the collector, then the other on the emitter. No matter which lead is used, there should be infinite resistance. Any lower reading, such as 50 ohms (which is typical on a bad transistor), indicates a short. This all sounds pretty confusing, but a little experience on a good transistor will make you an expert in no time. Usually, the lowest ohmmeter setting is used for testing transistors. Once in a great while a transistor may check out good on this test, but may actually be “leaky” or break down only on higher voltages. If in doubt, change it. Itis also wise to check the transistor out of the circuit just in case some component in the circuit is affecting the onmmeter reading. A diode is tested like a transistor except it only has two leads. Again, there shouldbe high resistance one way and little resistance the other. If it tests bad, take one lead out of the circuit in case somecomponentis messing up the ohmmeter reading.

NOTE: DONOT leave soldering equipment on the leads too long since all semiconductors, especially integrated circuits, are easily destroyed by heat.

Without special equipment, integrated circuits are checked by verifying the proper DC voltage on the pins and the correct AC wave form using an oscilliscope. BE CAREFUL: Shorting their pins can easily destroy them. Resistors are checked with an ohmeter and should usually be within ten percent of the value stated on them and on the schematic. You may have to desolder one lead from the printed circuit board. If you wreck the foil on the board, carefully solder a small wire over the break to reconnect the conductive foil. Capacitors are tricky. Their resistance goes up when checked with an ohmmeter which shows a charging action. As they suck up current from the meter, the voltage goes up and so does the resistance. If you are sure a particular circuit is giving you a problem and everything else checks out O.K., Electrolytic capacitors are prime suspects. Substitute a new one and keep your fingers crossed.

Theory of Operation

To understand what goes on inside the monitor, large general groups of circuits will be examined instead of \aboriously analyzing the branches and small circuits that make up these groups. This will help avoid confusion and aid in a basic, concrete, knowledge of what makes up a monitor.

THE POWER SUPPLY — The AC going to the monitor from the game transformer is just like the voltage and current from your wall outlet. It jumps up and down going positive and negative sixty times a second. But a monitor needs nice, smooth DC; direct current, not alternating. So diodes chop up the AC and a big electrolytic capacitor filters it out to make it even smoother. Since the monitor is a big piece of electronic equipment, with many circuits demanding a lot of power from the power supply, there are also zener diodes and transistors to help maintain a nice, constant, smooth voltage so that the monitor circuits don't jump around. And this is what happens when you see a wavy picture. There is AC creeping through the power supply, so it must be malfunctioning. If the voltage from the power supply is too low, the other circuits will be starved for power and you may see asmall, wavy picture, or noneatall. Some circuits receive voltages that are higher than what the power supply should put out. But they come from the flyback transformer which will be discussed later.

THE INTERFACE SECTION OF THE CHASSIS — The interface section of the chassis is fairly easy to identify. It is right by the place where ihe video jack(s) from the logic board(s) plug into. There are sets of transistors that receive the separate red, green, blue, and sync information from the cables that come from the logic boards. The Circuits jack up the voltage and match impedances, or in other words, prepare the logic board outputs for the circuits that will really amplify them for the output devices such as the yoke in the case of the sync, or the picture tube that shows the colors.

Page 78

An interesting aside is that our sync is composite negative sync. That means two things: 1, The sync is a negative going wave form.

  • There are two pulses going at different speeds over the same wire: a. Vertical wave forms at 60 times per second (or Hertz) and b. Horizontal wave forms at about 15,750 times per second (Hz). The sync is amplified by a sync amplifier transistor and sent on its way to the oscillators. The sync or timing information will be explained along with the oscillator shortly. The color information is sent via wires to the neck board where the main amplification occurs. This will also be discussed later.

VERTICAL AND HORIZONTAL DEFLECTION— After the sync signal is amplified by the sync amp, it goes to two different sections, the vertical and horizontal circuits. Basically, the sync signals are for timing so the picture doesn’t mess up since it is assembled like an orderly jigsaw puzzle, but so fast that you can't see the electron beams for each color painting the picture on the screen. This will all become clear soon. For now, we will follow the 60 cycle component of the syne as it goes on its journey to the deflection yoke. The 60 cycle pulse goes to the vertical oscillator to make sure this circuit goes back and forth (or oscillates) at 60 times a second. Without this pulse keeping the circuit at the correct speed, it may get lazy and oscillate at 58 cycles or lower, or get ambitious and oscillate at 62 cycles or higher. At the wrong speed, the picture will start to roll up or down. A Wells Gardner 13” (K4806) or 19” (K4906, K4956) color monitor uses an integrated circuit for its sync section. An Electrohome 13” or 19” color monitor uses an integrated circuit |C501 for its sync section. The Zenith monitor (CD19MXRFO06) also uses an IC for the sync processing. Wells Gardner uses HA11423, Electrohome uses HA11244, and Zenith uses 221-175 (their part number). These ARE NOT interchangeable! The idea is all the same. The output to the vertical amplifying transistors for all monitors must form a sawtooth wave form, sort of like a bunch of pyramids, racing through the yoke’s vertical coils at 60 times a second

Along the way to the output transistors, the 60 cycle pulse is shaped and amplified to do the job: the yoke magnetically pushes the electron beam to fill the screen out sideways looking at the screen with the greatest length going up and down. Or viewing the screen sitting like a home television set, the amplified vertical output fills the screen up and down. Watching a monitor like this, seeing only a horizontal jine means a problem with the vertical coils of the yoke or

5-7 anything from the vertical output section on back to the oscillator. The horizontal section is very similar with a few exceptions. The horizontal wave shape is more like a square and has a frequency of 15,750 cycles a second. Both Wells Gardner and Electrohome use the other side of their respective integrated circuits for the horizontal circuitry. If the oscillator isn't going at the correct speed, the picture may move sideways, start to slant, or tear up with slanted thin figures. With both the vertical and horizontal of all monitors, there are variable resistors that change the speed of the oscillators up and down. This way you have controls that can make the correct frequencies to keep the electronic jigsaw puzzle nicely locked in place. If you're driving in a car and next to you someone else is driving their car at exactly the same speed, it will appear that they are not moving. And this is why the sync frequency and the oscillator’s frequency must match, so the picture doesn’t appear to move. The correct wave form is shaped and amplified in the circuitry just like in the vertical section. But the horizontal output transistor is a!arge power transistor and not only serves to give current to the horizontal yoke windings, it also feeds the flyback transformer.

THE FLYBACK TRANSFORMER (OR HIGH VOLTAGE UNIT) — The picture tube needs high voltage to light up, and the power supply can't meet this demand. The flyback transformer receives current alternating at about 15,750 times per second from the horizontai output transistor. The “flyback” jacks up its input voltage and puts Out a higher voltage alternating at the same speed. But, in your “flyback” there are diodes that chop up the alternating voltage to makeit asmooth DC output just like in the power supply. This is what goes through that thick red wire to your picture tube. THIS AREA HAS ABOUT 24,000 VOLTS ON IT AND IT CAN KILL YOU! The “flyback” may be dangerous, but it is also generous. It has extra output windings which give voltage to the heater pins of the picture tube, voltage for the vertical deflection circuits, and picture tube screen-grid voitage. So in a way, the high voltage “flyback” is like a second power supply. COLOR CIRCUITS — The color circuits are pretty straight forward. The signals go into the interface section where some amplification and impedance matching occurs. These circuits are pretty sparse and simple. Each color just has two transistors and a diode with some resistors and capacitors. From here, the AC color signal is sent by wires to the neck board. The color output circuits are on the neck board. The color signais going to the transistors are controlled by two variable resistors called drive controls. There are only two, one for the red and one for the green on

Page 79

Wells Gardner and €lectrohome monitors. Zenith monitors have all three: red, blue and green. The Wells Gardner and Electrohome monitor have another variable resistor in their emitter part of their color output transistors. These “cutoff controls” vary the amount of A.C. signal that the transistor amplifies and sends to the cathodes of the picture tube. The Zenith monitor has its cutoff controls in the interface section to vary the amount of signal going to the output transistors. The more signal, the more color. If you think this is confusing, here is another little hitch. The Electrohome and Zenith monitors both have the actual A.C. picture information signal going through the emitters of the color output transistors. The Wells Gardner has the A.C. signal going to the base of the transistors. The blanking and beam limiting signals which come from the blanking and beam limiting transistors in the interface section go into the color output transistor base in the Electrohome and Zenith monitors, but enters into the emitter of the’Wells Gardner monitor's color output transistor. Should you feel adventurous enough to look at this signal on an oscilloscope, it should look like a square. The beam limiter helps controi the brightness level, and the blanking transistor rapidly turns the picture tube on and off so that retrace lines don’t show up on the screen. By turning up the brightness on a good monitor, these four to six retrace lines can be seen slanting diagonally across the picture.

PROTECTION CIRCUIT —

To protect the high voltage section against voltages that are too high coming from the power supply which could cause X-rays to be emitted from the “flyback”, a Circuit senses the higher power supply voltage and turns off the horizontal! oscillator. Since the horizontal oscillator doesn’t work, the horizontal output transistor has nothing to feed the “flyback” which in turn has nothing to feed the picture tube. The monitor will be silent, have no picture, and will appear to be off. But don't be fooled. There is still that excessive amount of voltage coming from the power supply. To find out, check at pin two of Wells Gardner's 1C501 and emitter of X04 for the Electrohome monitor. Check the 95 volt test point (located near the “flyback”) for the Zenith monitor. Here are the voltages you should receive: Wells Gardner = 130VDC Electrohome = 120VDC Zenith = 95VDC

The best place to measure this voitage on an Electrohome monitor is at a pin marked B1 on the chassis. This is because a 13 inch color Electrohome monitor, The GO07-FBO or G0O7-802, has an integrated circuit and very little else in the power supply. Still, there should be 120VDC at B1.

5-8 THE PICTURE TUBE (OR CRT) —

ATTENTION! For information on picture tube replacement types, go to the last section, “PICTURE TUBE INTERCHANGEABILITY”.

The picture tube or CRT is an output device. In other words, the end result of the circuit's work is displayed by this part. Actually, the output of other circuits is in the neck of the picture tube. First, there is the heater. The heater boils off electrons from the cathodes so that they (the electrons) shoot up to the screen to excite the phosphors so that the three phosphors emit three colors of light. _ The cathodes are next, and again they emit electrons to turn on the tube phosphors, making it glow. A defective cathode may cause the particular color it handles to be missing. Next come the grids. The first grid is grounded. The following grid is the screen grid which receives about 300VDC depending on the brightness setting. The next grid closest to the picture tube screen is the focus grid which gets about one fifth the amount of voltage that is applied to the picture tube anode. After jetting from the cathode through all these grids, the electrons speed through a mask, a sheet of material with tiny holes, and then excite the tiny dots of phosphor in the inside surface of the picture tube screen. The green electron gun (or cathode and circuitry) spits out electrons which head for the green phosphors only. The same goes for the red and blue guns. The way the phosphor light blends determines the color seen. Should these electron beams become too intense, they may burn the phosphor. With the monitor off, this can be seen as a dark permanent image of the video information on the tube screen.

Differences Between Monitors

The easiest way to identify the brand of monitor you are working with is to find the manufacturer's name or modei number printed on the chassis or chassis base. But what if the monitor was in a Texas dust siorm or buried in volcanic ash and this information is no longer there? Fear not! Each monitor has its own peculiarities and the following should help to identity them: The ELECTROHOME G07-904 (19”) and GO7-902 (13”) have their horizontat and vertical processing IC hidden under a silver can. A shiny metal top behind the “VERTICAL HEIGHT” and “HORIZONTAL FRE- QUENCY" control prove this is an Electronome monitor.

Page 80

The WELLS GARDNER K4906 (19) and K4806 (13”) have their horizontal and vertical processing IC out in the open directly behind the “VERTICAL HOLD” control. The ZENITH CO19MXRFO6 (19") monitor has its horizontal and vertical processing IC way in back by the picture tube. The monitor also has large white cables going trom the main board to the neck board. K4906 (1st TYPE) — This monitor's identifying tags have BLACK ink printed on a white background. There is NO Vertical Damping Control. (This Control would be next to the Vertical Hold Control but this area is jumpered with a small wire instead. 4906 (2nd TYPE) — This monitor's identifying tags have RED ink printed on a white background. There 1S a Vertical Damping Contro! next to the Vertical Hold Centrol. The Damping Control provides a few more lines on the top of the monitor screen (monitor viewed as a normal T.V. would be) for any video game that may need these lines to fit the picture on the screen. Moving the Control may distort the top part of your picture (or the side, depending onthe game and how the monitor is mounted) so go ahead and move it if you are having this type of problem. To accommodate this new feature, there are a few circuit changes. ONE MAJOR DIFFERENCE BETWEEN THESE TWO VERSIONS OF THE K4906 IS THE YOKE. They look the same but notice the part numbers: K4906 WITHOUT the Damper Control: 2021111201 K4906 WITH the Damper Control: 2021111258 Since the companies like to change part numbers at the drop of a hat, the best thing to do is to request whatever part number is written on your yoke. If you should get the wrong yoke, the results will be: Picture distortion. Excessive brightness. Too much or too little vertical picture size.

CONTROLS YOU MAY NOT TOUCH Basically, on the Electrohome monitor, you can move any control you want EXCEPT for the B1 control. This sets the power supply voltage (ideally at 120 VDC) and is located right behind VERTICAL HOLD. The 13" Electrohome DOES NOT have this control. It may also be wise not to move the VERTICAL LIN- EARITY since this distorts the picture and is hard to reset perfectly. If you do move it, turn on the Cross Hatch Test Pattern of your game and try to get the squares to the point where they are equal in size by readjusting this Linearity Control. On the Wells Gardner monitor, brightness is adjusted by the “BLACK LEVEL” Control which is right next to the Horizontal Frequency Control. Under the Focus Control is the “SCREEN” Control which youDO NOT touch. Yes, this contro! does adjust the brightness,

5-9 but it is used to set the CRT bias andis adjusted at the factory. When Wells Gardner sets it, they mark the position with a black mark on the knob. lf you moveit, be sure to realign the mark and THEN set the BLACK LEVEL Control to the brightness you desire. So, other than the SCREEN control, you may adjust any of the controls. The Zenith monitor has a 95 volt adjustment control. It is green and located behind the jack labeled 3D3. To discourage you from moving it, Zenith has placed a little glue on top of this control

Parts Interchangeability

Some parts can be interchanged on all of the monitors. Here are the rules:

  • You CAN swap any resistor between monitors that has the same resistance, wattage rating, and tolerance. You CAN swap any capacitor between monitors that has the same capacitance and voitage rating.

. You CAN swap many of the parts between the 19" and the 13” versions of each manufacturer's monitor. BUT, be certain to compare the manufacturers’ part numbers to be positive the parts you want to interchange are identical. BE SURE you have read the section DIFFERENCES BE- TWEEN MONITORS which was covered earlier.

You MAY BE ABLE to swap picture tubes between monitors. In the past you could swap any picture tube, but due to rampant engineering changes and new monitor models being introduced, you would need a computer to keep track of what could be swapped. For more information on this subject, go to “PICTURE TUBE INTERCHANGEABILITY”.

You CANNOT change any part that is a safety part, one that is shaded in gray on the schematic; it MUST be IDENTICAL to the original. To do otherwise IS DANGEROUS. For instance, the 13 inch Electrohome (G07-902) monitor “flyback” looks identical to the 19 inch Electrohome (G07- 904) monitor “flyback”. In fact, there is even a 19 inch Electrohome (G07-905) monitor (which is an obsolete model) with a similar looking “flyback". NONE OF THESE ARE INTER- CHANGEABLE!

You CAN change any of the parts between the G07-904 and GO7-907. They're essentially the same monitor except that the G07-907 has a vertically mounted picture tube.

Page 81

if there is any doubt about what parts can be swapped between each manufacturer's 19 inch and 13 inch models, compare the manufacturer's part number between each one. If they match up, they are the same part.

Picture Tube Interchangeability

13” MONITORS

There are currently two 13” monitors being used: the Wells Gardner K4806 and the Electrohome G07-902. The picture tubes used are NOT interchangeable. The pins on the neck of the CRT will not fit in the socket should you use the wrong CRT.

Here is a chart for all the 13” color monitors Bally Midway uses. ELECTROHOME — G07-902 — 370ESB22 WELLS GARDNER K4806 —370KSB22

19” MONITORS. Here it gets a little tricky. All of the picture tubes will fit no matter which is used. But if you use the wrong one, you will have problems with purity and/or dynamic convergence. Purity trouble means that the color won't be true. If you turn up the color control for one color, instead of seeing that solid color it will show blotches or blobs of other colors on the screen.

Trouble with dynamic convergence means that there will be color fringing around solid lines at the edges of the screen.

The only way to ensure that you avoid these problems is to get the right picture tube or the right substitute.

Here is a list of the 19” monitors and the CORRECT CRT numbers.

ALL ELECTROHOME G07-904 — 19VMNP22 RCA 19VMJP22 RAULAND 510UJB22 HITACHI

WELLS GARDNER K4906 — IOVLTP22 RCA 19VMLP22 ZENITH 19VMKP22 PHILLIPS

ZENITH CD19MXRFO6 — 19VMLP22 ZENITH 19VLTP22 RCA 19VMKP22 PHILLIPS The factory recommended CRT type could change in the future for one reason or another, but the listed picture tubes will work. As a matter of fact, you can call another picture tube company to see if they have a replacement number to recommend...but caveat emptor — let the buyer beware.

Page 82

his

Schematics

Page 83

19” COLOR MONITOR SCHEMATIC DIAGRAM

MODELS 19K4901, 19K4906, 19K4951, 19K4956 Power Supply Voltage and Symbols

[]"
||ci
|_Symbol_|Voltage |Operating CircuitOSCILLOSCOPE WAVEFORM PATTERN
|®|15vVert. Osc.:The waveforms shown are as observed on the wide band
|SyncX-RAY RADIATION PRECAUTION:REPLACE SAFETY CRITICAL COM.oscilloscope with the monitor turned to a reasonably
BlankingPONENTS ONLY WITH MANUFAC-strong signal and a normal picture. The voltages shown
|CRT Cut-OffTHIS PRODUCT CONTAINS sunita|TURER'S RECOMMENDED PARTS.on each waveform are the approximate peak ampli-
T‘ELECTRICAL AND MECHANICAL PARTAVERTISSEMENT:POUR MAINTENIRtudes.
||:'4
e130VHore oe©ESSENTIALFOR X-RAY RADIATION |oe rAcee teat CaNoenisIf the waveforms are observed on the oscilloscope with
||Hqhigh frequency response, the corner of the
|jHorz. Output::|DONT LE FONCTIONNEMENT ESTa poor2
||Vert. Output__FOR REPLACEMENT PURPOSES, USE| CRITIQUE POUR LA SECURITE QUE PARa wil ai Se eee
LY TYPE PARTS SHOWN IN THE=DES PIECES RECOMMANDEES PAR LEandthe amplitude of any high frequency pulse will
©175V_ | Video OutputDante “er:FABRICANT.tend to be less.

Q351 COLLECTOR

94019.402,0493
RED OUTGREEN OUT_@LUE OUT.

2SC2088 B/L86K 2SC2068.8/L 89K 25C2068L 6/ 88K 2SCIIABVC/CVC 2SCISI4BVCKVC 2SCISI4BVC/CVE

Bet age

oz

1VIDIV 200uSECIDIV20VIDIV 10uSECIDIVO.5/DIV SMSECIDIV2sciei5v/GR_

BSCaa5 tone: | n2oe <a te 7 2 2scieisanzy Os 2SC P45, jal Rae | Bot21 op TP-31 DC COUPLED 1402-3 BOTTOM LINE=0 VOC

[G.ORIVE] [R.CUTORF] [G.COTOFF]

SYNC AME :

2VIDIV 200MSECIDIVO.5/DIV 20u SECIDIV)[zseieisyloor a esse7358352
lzscoasveeee,SoS
LC. 901, PIN 31.6. 301, PIN 15©cae2spe69

bis HOR.ORIVE = * OHSS) oeeaae2BK ah 2808988 ZSCZEIOBK

coh ws)

kevioov VERT * Sse f i

,——|“i
1301aellcae33K Servees |g R702

1VIDIV SMSECIDIV 1VIDIV 20u SECIDIV

P82 ‘1P-31, AC COUPLED

SYNC AMP vosc HOSC_—4haeimerLy(ad vei
a=MOex;gure

: cows mee

[VeRT?- 3»i
“=eKa
Bie)“rao”om centre)
1.6. 201, FIN 13NEGATIVE SIDE OF C303iiei2|eaecama |[%YLT
-2.033\z3!T382
20VIDIV SMSECIDIVAVIDIV 200uSEC/DIV2VIDIV 10uSECIDIV

acr2ov ‘sone coz #380

gL

5-121VDIV 200uSECIDIV2VIDIV SMSECIDIV1VDIV 2MSEC/OIV
DeRAUESING CON,:.K4901D, K49060, K4951D 5833

| ~ K4956B

Page 84

REPLACEMENT PARTS LIST

This monitor contains circuits and components Included specifically for safety purposes. For continued protection no changes sho :id be made to the original gesign, and components shown in shaded arsas of schematic, ov ¢ & on parts list should be replaced with exact factory replacement parts. The use of substitute parts may create a shock, fire, radiation c: other hazard. Service should be performed by qualified personnel only.

MAIN BOARD

Rat. No.Part No.DegoriptionRe}. No.Part No.Description

RESISTORS RESISTORS (CONT)

R201203x6500-6454K Ohm, 5%. 1/4W CarbonR369203x6802-32080K Ohm, 5%, 1/2W Comp.
R262203%6500-52330 Ohm, 5%, 1/4W CarbonF370203X6501-00233K Ohm, 5%, 1/4W Carbon
R203203X6500-405100 Ohm, 5%, 1/4W CarbonR371203X9014-5841K Ohm, 5%,1W MetaiOxide
R204203X6700-327100 Ohm, 5%, 1/2W CarbonR972208X9101-11942K Ohm, 5%, 1W Metal Oxide
205203X8700-421270 Ohm, 5%, 1/2W CarbonRATE203x6700-763,88K Ohm, 5%,1/2W Carbon
R206203X6500-540390 Ohm,8%, 1/4W CarbonR378203x9104-404270 Ohm, 5%, 2W Metal Oxide
R2073402201934260 Ohm, 5%, 1/4W CarbonR377203X6500-447450 Ohm, 5%, 1/4W Carbon
R208203X6500-540380 Ohn,5%, 1/4W CarbonR378203X6500-88610K Chm, 5%, 1/4W Carbon
F209340X2201-994200 Orim, 5%, 1/4W CartonR379203X6500-88640K Ohm, 5%, 1/4W Carbon
R210203X6500-540390 Ohm, 5%, 1/4W EarbonR380203%6500-8658.2K Ohm, 5%, 1/4W Carbon
Ratt340X2201-934200 Ohm, 5%, 1/4W CarbonA381203X6500-7242.2K Ohm, 5%, 1W Metal Oxide
R214203X6500-6451K Ohm, 5%, iW CarbonF383203X9014-387150 Ohm, 5%, 1W Metal Oxide
A215203X8501-126100K Ohm, 5%, 1/4W CarbonR502203X6500-88610K Ohm, 8%, 1/4W Carbon
R216203X6500-6451K Ohm, 5%, 1/4W CarbonR503204X1706-535,150 Ohm, 5%, 15W Metal Oxide
R217203X6500-405100 Ohm. 5%, 1/4W GarbonR504203X9014-26747 Ohm, 5%, 1W Metal Oxide
R218203X6500-6451K Onm, 5%, 1/4W CarbonR508,203X6801-2092.2K Ohm, 5%. 1/4W Carbon
R219203X6501-126100K Ohm, 5%, 1/4W CarbonR506203X9104-105,15 Ohm, 5%, 2W Metal Oxide
220203X6500-6451K Ohm, 5%, 1/4W CarbonR507203X5602-185330K Ohm, 5%, 1/2W Comp.
R221203X6500-405100 Ohm, 5%, 1/4W CarbonA*REO1204X1625-0583.3 Ohm, 5%, 10W WW
R222203X6500-7623.3 Ohm, 8%, 1/4W CarbonR701203X9105-1412.2 Ohm, 5%, 2 Metal Oxide
224203X6500-169,10 Ohm, 5%, 1/4W CarbonR702203X6206-4412.2 Ohm, 5%, 1/2W Carbon
R225203X6500-16910 Ohm, 5%, 1/4W CarbonR201204x2070-0722K Ohm-B Semi-Fixed
R226203X6500-169410 Ohm, 5%, 1/W CarbonR301204X2070-0845K Ohm-8 Semi-Fixed
Rea?203X6501-04447K Ohm, 5%, 1/4W CarbonVR303204X2070-055
R228203X6500-6451K Ohm, 5%. 1/4W CarbonR351204x2070-0722K Ohm-B Semi-Fixed
R229203X6700-421270 Ohm, 5%, /2W CarbonR352204x2070-0722K Ohm-B Semi-Fixed
R230203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R231203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R232203X6500-8638.2K Ohm, 5%, 1/2W Comp.
R233203X6500-468180 Ohm, 5%, 1/4W Carbon
A234340X2820-03482 Ohm, 5%, 1/4W CarbonCAPACITORS
R235340X2820-93482 Ohm, 5%, 1/4W Carbonc201203X0014-0881000 uF, 16V, Electrolytic
R236340X2820-93482 Ohm, 5%, V4W CarbonC202202X7200-084330 pF, 500V, Ceramic
R301203X6500.508270 Ohm,5%, 1/4W CarbonC203202X7200-043220 pF, 50QV, Geramic
R302203X6500-8636.2K Ohm, 5%, 1/4W CarbonC204202X7200-043220 pF, 500V. Ceramic
R303203X6500-8638.2K Ohm, 5%, 1/4W Carbon205203X0014-076470 uF, 16V, Electrolytic
R304203X6500-7242.2K Onm, 5%, 1/4W CarbonC208203X1810-1490.1 uF, 125V Mylar
F305203x6500-8426.8K Ohm, 5%, 1/4W CarbonC207349X2232-109022 uF, 100V Mylar
R306203X6003-2017.5K Ohm, 2%, 1/4W CarbonC301203X0014-065330 uF, SQV Electrolytic
R307203X6500-82558K Ohm, 5%, 1/4W CarbonC302203X1600-5630.033 uF, 50V Mylar
R309203X6500-865,22K Ohm, 5%, 1/4W Carbon303203X0629-0373.3 uF, 50V Electrolytic
R310203X6500-988,39K Ohm, 5%, 1/4W CarbonC304203X1800-3660.068 pF, 50V Mylar
R311203X6500-7623.3K Ohm, 5%, 1/4W CarbonC306203K0412.0122.2 uf, 16V Tantal
R312203X9014-7414.7K Ohm, 5%, \4W Carbon307203X1600-6340.033 UF, 50V Mylar
313204X 1450-5374K Ohm, 5%, 5W Carbon308203X0025-1743.3 uF, 50V Electrolytic
R314203X6500-481220 Ohm, 5%, 1/4W CarbonC309203x1207-1000.068 uF, 100V PP
R315203X6500-16910 Ohm, 5%. 1/4W CarbonC310203X0629-06110 uF, 100V Electrolytic
R316203X6500-7623.3K Ohm, 5%, 1/4W CarbonC311203X0041-02510 uF, 160V Electrolytic
R317203X6700-10712 Ohin, 5%, V/2W CarbonC312202X7050-2484000 pF. 500V Ceramic
R3182036500540390 Ohm, 5%, 1/4W Carbon6313203X0040-05247 uF, 160V Electrolytic
R318203X6500-6451K Ohm, 5%, 1/4W Carbon314203X1201-2650.033 uF, 200V PP
R320203X6501-00233K Chm, 5%, t/4W CarbonC315203x0629-0231 uF, 50V Electrolytic
R321203X6501-224270K Ohm, 5%, 1/2W CarbonC351203x0629-0231 uF, 50V Electrolytic
322203X6500-88640K Ohm, 5%, 1/4W CarbonC352203X0619-04547 uF, 2V Electrolytic
8351203X6500-88610K Ohm, 5%, 1/4W CarbonC353203X1190-0150.0082 pF, SOV Mylar-PP
R352203X6500-7853.9K Ohm, 5%, 1/4W CarbonC354203X0619-04547 uF, 25V Electrolytic
R353203X6501-08668K Ohm, 5%, 1/4W CarbonC355203X1600-3660.0068 pF, SOV Mylar
R354203X6500-7623.3K Ohm. 5%, 1/4W CarbonC356202X7050-4830.01 uF, 500V Ceramic
R355203X9205-1436.8K Ohm, 5%, 3W Metal OxideC359202X8065-606100 pF, 500V Ceramic
R358203X5601-87858K Ohm, 5%, 1/2W CarbonC360202X7050-3660.0033 pF, 500V Ceramic
360203X8600-561470 Ohm, 5%, 1/4W CarbonC361202X7050-4830.01 uF, 500 Ceramic
R361203X6500-88610K Ohm, 5%, 1/4W CarbonC362202X7209-0320.01 uF, 60V Ceramic
R362203X9014-645,1.8K Ohm, 5%, 1W Metal OxideA*C363203X1270-9118700 pF, 1.5 KV PP
R363204x 1527-7513.9K Ohm,5%, 7W Metal OxideWC365203X1201-2650.33 uF, 200V PP
R364203X6500-24622 Ohm, 5%, 1/4W CarbonC366203X0019-02822 uF, 25V Electrolytic
R3652036501-00233K Ohm, 5%, 1/4W CarbonC367202X8065-1626 pF, 500V Ceramic
R367203X6500-88610K Ohm, 5%, 1/4W CarbonC368202X7203-0320.01 uF, 50V Ceramic
R368203X5602-185330K Ohm, 5%, 1/2W Comp.car2203X1207-1250.1 uF. 100V PP

Ret. No.

A C380 C501 4 cs02 4 C503 4 C504 C505 C507 cro2 C703 MAIN BOARD (CONT)

Part Ne. Description

Part No.DescriptionRet. No.

CAPACITORS (CONT.)

202X7200.087470 uF, 500V Ceramic206
203X1810-1490.1 uF, 125V Mylar207
202X7050-2821600 pF, S00V Cerantic208
202X7810-2142200 pF, 125V Ceramic209
202X7810-2142200 pF, 125V Ceramic210
203x0220.075560 uF, 200V ElectrolyticQ301
203X0040-03422 UF, 180V Electrolytic9302
203X0041-057,47 uF, 160V ElectrolyticQ303
203x0010.0921000 UF, 25V Electrolytic951
203x0634.06110 uF, 100V Electrolytic352
202X7080-2481000 pF, S00V CeramicI¢301

A% (C501 SEMICONDUCTORS 201X2010-159 Diode, 1S2076-27 201X2010-159 Diode, 1$2076-27

201X2010-159Diode, 12076-271351
201X2010-189Diode, {2076-27L362
201X2010-159,Diode, 1$2076-27L701
201X2010-189Diode, 18207627ee
201X2010-159Diode, 1$2076-27AwT352

201X2010-165 Diode, 1S$81 201X2010-159 Diode, 1$2076-27

201X2010-159.Diode, 1S2076-27AF5O1
201X2120-009Diode, RH-IVJ402
201X2120-009Diode, RH-IVP201
201X2010-159Diode, 1S2076-27P202
201X3120-216Diode, RM-1AVP4071
201X3120-216Diode, AM-1AV501
201X3120-216Diode, RM-1AVP6O1
201X3120-216Diode, RM-1AVTHS501

201X3120-216 Diode, RM-1AV 201X3120-216 Diode, RM-1AV. 201X2130-234 Diode, RU-2V 201X2120-009 Diode, RH-1V 200X3181-523 Transistor (NPN) 2SC1815GR 200%3181-523 Transistor (NPN) 2SC1815GR 200X4056-260 Transistor (PNP) 2SA562-Y-TM 200X4056-260 Transistor (PNP) 2SA562-Y-TM 200X4056-260 Transistor (PNP) 2SA562-Y-TM

NECK BOARD RESISTORS

203X6000-729220 Ohm, 5% 1!4W Carbon401
203X6500-540390 Ohm, 5% 1/4W CarbonC402
203X6000-661820 Ohm, 5% 1/4W CarbonC403
203X6000-723220 Ohm, 5% 1/4W Carbon.404
203X6500-540390 Ohm, 5% 1/4W CarbonC405

2036000-661 820 Ohm, 5% +/4W Carbon 203X6000-729 470 Ohm, 5% 1/4\W Carbon 203X6000-998 270 Ohm, 5% 1/4W Carbon

203X6000-661820 Onm, 5% 1/4W Carbon401
203X9104-82415K Ohm, 5% 2W M.O. FormingQa02
203X9104-82415K Ohm, 5% 2W M.O. Forming403

203X9104-824 15K Ohm, 5% 2W M.O. Forming 203X6000-998 2.7K Ohm, 5% 1/2W Comp. 203X6000-998 2.7K Ohm, 5% 1/2W Comp.

203X6000-9982.7K Ohm, 5% 1/2W Comp.401
203X9105-1542.2 Ohm, 5% 2W Metal OxideP402
203X6500-7412.7K Ohm, 5% 1/4W CarbonP403
203X6500-7412.7K Ohm, 5% 1/4W CarbonP701

203X6500-741 2.7K Ohm, 5% 1/4W Carbon 204X2115-014 500 Ohm, -B Semi-Fixed 204X2115-014 500 Ohm, -B Semi-Fixed 204X2115-006 5K Ohm, -B Semi-Fixed 204%2115-006 5K Ohm. -B Semi-Fixed 204X2115-006 5K Ohm, -B Semi-Fixed SEMICONDUCTORS (CONT) 200X3181-529 200X3181-523 200X3181-523 200X3181-523 200X3181-523 200X3181-523 Transistor (NPN) 28C1815G" Transistor (NPN) 26C1815GR Transistor (NPN) 25C1815GR Transistor (NPN) 2801851GR Transistor (NPN) 28C1851GR. Transistor (NPN) 25C1851GR 200X3207-306 Transistor (NPN) 28C2073L8Gi2 200X3207-308 Transistor (NPN) 28C2073LBG1.2 200X3248-217 Transistor (NPN) 28C2482BK 200x4589-802 Transistor (NPN) 2608988 200X2300.033 IC HA11423 200X2600-183 IC STR381 TRANSFORMERS & COILS 201X4710-134 Coil, (RF Choke) 201X5000-083 Coll, Horiz. Size 611X0004-007 Coil, Adg. 202X 1300-080 Transformer, Hor, Drive 200x9720-301 HV-Unit M-11 MISCELLANEOUS 204x7120-073 Fuse, 4 Amp. 125V 206X5008-632 Recep W Wire 3P-M-BG 204X9600-486 Plug, PWB 3P-J 204X9601-477 Plug, PWB 6P-Q 204x9600:298, Plug, PWB 4P-8 204x9600-249 Plug, PWB 2P-B 204X9600-304 Plug, PWB 4P.C 201X0100-112 Thermistor FINAL ASSEMBLY PARTS AW 88X0138-506 205X9800-158 A We 202X1111-201 204X9301.255 49VLTP22 Pix Tube Lateral/Purity Assembly Yoke Detlection CRT Socket 291X5004-262 Automatic Degaussing Coil Unit

CAPACITORS 202X7050-269 1200 pF, 500V Ceramic 202X7050-248 1000 pF, 500V Ceramic 202X7050-248 1000 pF, 500V Ceramic 202X7050-282 1500 pF, 1.5KV Ceramic 202x7950-483 2.01 uF, 500V Ceramic SEMICONDUCTORS 200X3206-800 Transistor (NPN} 28C2068LB 200X3206-800 Transistor (NPN) 28C2068L8 200X3206-800 Transistor (NPN) 2SC2068LB MISCELLANEOUS 206X5009-296 RECEP W Wire 4P-€ 204X9600-254 Plug, PWB 3P-A 204X9600-98 Plug, Pin 1P-D 204x9601-020 Plug, PWB 4P-E

$-13

Page 85

+ lus onten Rep X101.XI03 ond XI0S VIDEO AMR. 25C484C

wea rvensme Qt | Pek 308

X303 OEAM LIMITER 2SA673 Tesa,xsce.nsoaxsoe | syn jescoat or aaciee:

%304 BLANKING 28C484C or ascicee

X901 POWER DRIVE 252686 X 902 ERROR AMP 2SC1890 ° Xi02.X104 ond XI06 VIDEO AMP. 28A673C or B8cisiaV 03 R,GB VIDEO OUTPUT

Bocca 2sciesa R REGULATOR vr 9)

wy Fs ae at, BIBER foce ca cur we rn HRI

HES)

SU-1133A MAIN PCB ASSY

28c4a54¢ or 2sci6es

ACIZOV 6OHs/50Hz 10% BSczen or 882Esi0aK 250869 230820 7 x50 H.R HOUT X7Ot JCRAY PROTECTOR. Beth WE, ascasrv S000 oF te ay-s0328 BEFLecTiON YoxE

00-4147-04 G07-CBO Schematic Notes Unless otherwise specified Resistance: (Q.) (K->KQ, M->MQ), 1/4 (W) carbon resistor Capacitance: 1 or higher—> (pF), less than 1-> (yF) working voltage > 50 (V) ceramic capacitor Inductance: (/ H) Electrolytic Cap: Capacitance Value (v F)/working voltage (V), NP — non-polar (or bipolar) electrolytic cap. Refer to the parts list for additional component information. 2 indicates test point connection ah indicates chassis ground unless otherwise specified Hz _ indicates cycles per second For safety purposes (and continuing reliability) A replace all components marked with safety syrnbol with identical type. NOJE: FR — fusible resistor ——e22—-

Parts identification on circuit boards: e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

Page 86

REPLACEMENT PARTS LIST—-ELECTROHOME 19" MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics

important to safety.

DO NOT degrade the safety of the set through improper servicing.

Abbreviations for Resistors and Capacitors

Resistor Capacitor

CR:Carbon ResistorC Cap.:Ceramic Capacitor
Comp. R:Composition ResistorM Cap.:Mylar Capacitor
OMR:Oxide Metal Film ResistorE Cap.:Electrolytic Capacitor
VR:Variable ResistorBPECap.:Bi-Polar (or Non-Polar)
MFR:Metal Film ResistorElectrolytic Capacitor
CMF R:Coating Metal Film ResistorMM Cap.:Metalized Myiar Capacitor
UNF R:Nonflammable ResistorPP Cap.:Polypropylene Capacitor
FR:Fusible ResistorMPP Cap.:Metalized PP Capacitor
PS Cap.:Polystyroi Capacitor
Tan. Cap.:Tanta! Capacitor
NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, and model number. Complete information will help expedite the order.

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, fire or other hazards. For maximum reliability and performance, ali parts should be replaced by those having identical specifications.

SERVICE REPLACEMENT PARTS LIST

SymboiDescriptionPart Number

Main PC.B. Ass'y SU-1133A CRT Socket PC.B. Ass'y SU-3032A Purity Shield Ass'y 07-220083-03

Outside of the P.C.B. Ass'y Symbol —_ Description Part Number Picture Tube 19" 17-7198-03

AA\Deflection YokeA29779-D=21-141-01

PC Magnet A75034-B=29-32-01

AA\Flyback Transf.A29951-B
AAHVRA46600-A
ROSUNF Resistor 2202,25W KQRF258K-221

co4 C Capacitor 150pF, AC1.5KV —_ QCZ0101-005

X01Si. Transistor2SD870
x02Si. Transistor2SC1106A
scScrew #8-%31-610818-06
scScrew % x % Pix Tube Mig.(4)31-601418-12
WAPyramidal Lock Washer (4)33-255-01

Nut Retainer, Pix Tube Mtg. (4) 33-494-01 Clip—P.C.B. Support 33-629-02 Standoff 33-670-010R-02 Wire Terminal (Gnd. Strap) 34-228-03 Terminal Lug (Gnd.) 34-33-04 Groundstrap Assy. 34-574-02 Grounding Spring 35-212-03 Wire Hook (Gnd. Strap) 35-3053-02 Purity Shield Holddown Clamp 35-2348-01 Support Brkt. RH 35-3890-01 Support Brkt. LH 35-3890-02 Chassis Base 38-449-02 Yoke Wedge (3) 39-1233-01 Purity Shield Ass'y. Parts List

SymbolDescriptionPart Number

Degaussing Coil 21-1007-30 D911,

D912Rectifier 1 Amp 600V (2)28-22-27

Pin Terminal (2) 34-708-01 Pin Terminal Housing 34-709-01 Purity Shield (2 pcs.) 35-3847-01 Purity Shield (2 pcs.) 35-3847-02

C911Capacitor 100nF 10% 400V48-171544-62
R921Resistor, Wirewound 332, 4W42-113301-03

Fire Retardant Term, Strip4 Lug — 34-492-09

CRT Socket P.C.B. Ass'y (SU-3032A) Parts List

Resistors

SymbolDescriptionPart Number
3105VvR200QVZ3234-022
R3106vR200QVZ3234-022
R3113vR5KQVZ3234-053
R3114VvR5KQVZ3234-053
R3115vR5KQVZ3234-053
R3116OMR10K22WJQRGO29J-103
R3117OMR10K22WJQRGO29J-103
R3118OMR10K22W JQRG029J-103
R3119Comp.R3.3KQ%W KQRZ0039-332
R3120Comp.R3.3KQ%W KQRZ0039-332
R3121Comp.R3.3KQ%W KQRZ0039-332

Capacitors

SymbolDescriptionPart Number
3107ECap.10uF 250VAQEWS3EA-106
C3108CCap.1000pF DC1400VPQCZ9001-102M

CRT Socket P.C.B. Ass'y (SU-3032A) Parts List (Cont.)

Colls Symboi L3101

Somisenductors Symbol 3101 X3102 X3103

Miscellaneous Symbol A Description Peaking Coil

Description Si. Transistor Si. Transistor Si. Transistor

Description ASCRT Socket

Main PCB Ass'y (SU-1133A) Parts List Resistors Symbot R1406 R1408 R1410 R144 R1415 R1421 R1422 AFR1401 AR1503 R1504 R1509 R1512 RI514 R1515 R1522 R1523 R1528 R1534 VR1501 AR1703 AR1704 AR1901 R1902 R1903 R1904 R1905 AQ1908 A\R1909 R1910 A\FR1901

Capacitors Symbol C1301 1402 1407 C1411 C1412 C1508 Aci512 AC1513 Ac1514 C1515 C1520 C1523 C1524 AC1531 Ac1532 C1904 C1905 Description

vy-R2002
voR2008
CMFR6801WJ
OMR33K21WJ
OMR27KQ1WJ
OMR12K22WJ

VR 10K AF R 6822W K

ACMFR11.8KQYW+1%

VOR 5KQ

OMR10KQ2WJ

OM R 62kKQ2WJ

OMR82022WJ
CMFR8.201WJ
CMFR4.701WJ
OMR6822WJ
OMR39001WJ

ZN R ZN OR

ACMFR392%W+1%
ACMFR7.68KQY¥W+1%

A’Posistor

UNFR227WK

CMF R 4.723WJ

OMR10K22W J
OMR18K21WJ
ACMFR472%W+1%
vR2KQ
ACMFR2.74KQ%W+1%
AFR2202%WK

Description BPE Cap. 3.3uF 50V A Tan Cap. 2.2uF 16V K E Cap. 4.7uF 6.3VA E Cap. 100uF 160V A E Cap. 3.3uF 160V A PP Cap. 5600uF 50V J APP Cap. 2000pF DC1500V J APP Cap. 2000pF DC1500V J APP Cap. 2000pF DC1500V J PP Cap. 0.53uF DC1200V J BPE Cap. 3.3uF 50V A E Cap. 1uF 160VA M_ Cap. 0.1uF 200V K APP Cap. 2000pF DC1500V J APP Cap. 1500pF DC1500V J E Cap. E Cap. 10uF 250V A Part Number QQLO43K-101

Part Number 28C1514VC 28C1514VC 28C1514VC

Part Number A76068

Part Number QVZ3230-002 QVZ3230-002 QRX019J-6R8 QRGO19J-332 QRGO19J-272 QRGO026J-123Z, QVZ3230-014 QRH024K-680M QRV142F-1182 QVZ3230-053 QRGO26J-103Z QRGO26J-822Z QRGO26J-821Z QRX019J-8R2 QRX019J-4R7 QRG026J-680Z QRGO19J-391 ERZ-CO5ZK471 ERZ-CO5ZK271 QRV122F-3902 QRV142F-7681 A75414 QRFO76K-2RO QRX039J-4R7 QRGO026J-103Z QRGO19J-183. QRV122F-470Z QVP5AOB-023E QRV142F-2741 QRH124K-221M

Part Number QEN61HA-335Z QEES1CK-225B QEW51JA-475 QEW52CA-107 QEWS2CA-335 QFP31HJ-562 QFZ0082-202 QFZ0082-202 QFZ0082-202 QFZ0067-534 QEN61HA-335Z QEW62CA-105Z QFM720K-104M QFZ0082-202 QFZ0082-152 QEY0034-001 QEWS2EA-106 Main PCB Ass'y (SU-1133A) Parts List (Cont.) Coils Symbol L1502 L1503 L1504

Transformers Symbol 71501 T1503

Semiconductors Symbol 11501 X1101 x1102 X1103 X1104 X1105 X1106 X1301 X1302 X1303 X1304 X1305 X1401 x1402 X1501 X1901 x1902 D1101 D1102 D1103 01301 D1401 1402 D1503 D1504 D1505 D1506 D1507 D1508, Ap1701 A\D1901 AD1902 401903 AD1904 A\D1905

Miscellaneous Symbol A\F1901 AF1902 Description Linarity. Coil Width Coil Heater Choke

Hor. Drive Transf. Side Pin Transf.

Description Ic Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Transistor Si. Diode Si. Diode Si. Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Zener Diode Si. Diode Si. Diode Si. Diode AdZener Diode ASi. Diode ASi. Diode ASi. Diode ASi. Diode AZener Diode

Description AfFuse 1.254 ANUL Fuse 3A Part Number AS39835, C30380-A C30445-A

Part Number A46022-BM C39050-A

Part Number HA11244 2SC1685(R) 2S8A673(C) 2SC1685(R) 2SA673(C) 2SC1685(R) 2S8A673(C) 28C1685(R) 2SC1685(R) 2SA673(C) 28C1685(R) 28C1685(R) 28D478 28D478 28C2610BK 2SC2688 (K.L.M.) 2SC1890A (E.F) wo6A woeA woeA 1SZ473H 18Z473H RD10F(C) HF-1 VO9E RD11E(B) Wo6A 18881 1SZ473H RD20EV2 181887A 181887A 1$1887A 181887A RD6.8EV3

Part Number QMF53U1-1R25S QMF66U1-3ROS

Page 87

fot XiGl X108 ene KiO8 VIDEO AMP 28C484C 2801603

>= SU-11034 _. MAIN PCB ASSY

Schematic Notes Unless otherwise specified Resistance: (Q) (K-*KQ, M--MQ), 1/4 (W) carbon resistor i 2 Capacitance: 1 or higher (pF), less than 1 (yF) REFLECTION voKE working voltege—» 50 (V) ceramic capacitor inductance: (» H) “ 4 Electrolytic Cap: Capacitance Value (y F)/working voltage (V), ¥701_ X-RAY. PHOTECTOR ASO MORNE ospiy out t ssc sonne Y) Vascor meanen NP - non-polar (or bipolar) electrolytic cap. 2SCASAC or 25C 1055 28C2611 or BSC26I08K Refer to the parts list for additional component information. Acev éomieon 2 indicates test point connection sion zh indicates chassis ground unless otherwise specified

Hz _ indicates cycles per second For safety purposes (and continuing reliability) A replace all components marked with safety symbol with identical type.

NOTE: FR - fusible resistor ——¢3-'

G07-FBO Parts identification on circuit boards: 00-4147-03 e.g. SU1126A (R107 = R1107) SU3030A (R113 = R3113)

5-16

Page 88

REPLACEMENT PARTS LIST—ELECTROHOME 13" MONITOR

Components identified by the A symbol in the PARTS LIST and on the Schematic have special characteristics Main P.C.B. Ass'y (SU-1103A) Parts List CRT Socket P.C.B. Ass'y (SU-3016A) Parts List Capacitors Resistors

important to safety.SymbolDescriptionPart NumberSymbolDescriptionPart Number
.ooC1402Tan. Cap. 2.2uF 16V KQEES1CK-225BR3105VR 2002QVZ3234-022
DO NOT degrade the safety of the set through improper servicing.C141£Cap. 100uF 160V AQEWS52CA-107R3106VR 2002QVZ3234-022
C1412ECap.3.3uF 160V AQEW52CA-335R3113VvR5KaQQVZ3234-053
1508PP Cap. 5600pF 50V JQFP31HJ-562R3114VR SKQVZ3234-053
iatii151ap.pI¥-
Abbrevlationsitor, Resistors end CapecttorsAcis13APP Cap, 2000pF DC1500V J QFZ0082-202R3117OM R 10Ka2WJQRGO29J-103
.Acis14APP Cap. 2500pF DC1500V. J QFZ0082-252R3118OM R 10Ka2W JQRGO29J-103
ResistorCapacitorC1515PP Cap. 0.53uF DC1200V K QFZ0067-534R3119Comp. R.3.3K2%W KQRZ0039-332
|..C1520BPE Cap. 1uF SOV AQEN61HA-105Z3120Comp. R 3.3KQ%4W KQRZ0039-332
CR:Carbon ResistorC Cap.Ceramic CapacitorC1524M_Cap. 0.1uF 200V KQFM72DK-682MR3121Comp. R’3.3K2%W KQRZ0039-332
Comp.RComposition Resist.MCap.Mylar CapacitorC1904ECap.QEY0034-001
OM RGhide Mi tal Film Rosi StE pia pElectrolyti CapacitorC1905ECap. 10uF 250V AQEWS52EA-108Capacitors
ideMetalFilmResistorp.'icCapacitorAc1907_AMM Cap. 0.1uF AC150VZ — QFZ9008-104SymbolDescriptionPart Number
VR:Variable ResistorBP E Cap.Bi-Polar (or Non-Polar)C3107E Cap. 10uF 250V AQEWS52EA-106
MFR:Metal Film ResistorElectrolytic CapacitorCoils.C3108CCap. 1000pF DC1400VP= QCZ9001-102M
CMF RCoating Metal Film ResistorMM Cap.Metalized Mylar CapacitorSymbolDesorptionPart Number;
.‘11501Peaking CoilA75360-6Coils
UNF R:Nonflammable ResistorPP Cap.Polypropylene Capacitor1502Liniarty Coil439934SymbolDescriptionPart Number
FR:Fusible ResistorMPP Cap.Metalized PP CapacitorL609Width Coit ,€80980-13101Peaking coilQQL043K-101
iL16jeaterChoke
ic meBiit a ucclior11901Line FilterA30475-JSemiconductors
.Gap.PitransformersSymbol_ DescriptionPart Number
7iiinthislistiiX3101Si. Transistor2802611
NOTE: When ordering replacement parts please specify the part number as shown in this list including part name, andSymbolDescriptionPart NumberoeSi yensietorSczel1
model number. Comriete information will help expedite the order.T1501Hor. Drive Transf.A46022-BMX3103Si. Transistor2802611
'.7aeT1503Side Pin Transf.C39050-A

Use of substitute replacement parts which do not have the same safety characteristics as specified, may create shock, Miscellaneous

fire or other hazards. For maximum reliability and performance, all parts should be replaced by those having identicalenerSymbolDescriptionPart Number
specifications.SymbolDescriptionPart NumberACRT SocketA75522
IC1501LC.HA11244
SERVICE REPLACEMENT PARTS LISTMain P.C.B. Ass'y (SU-1103A) Parts Listxis”Siianeisiorgencrsicl’
X1103Si. Transistor28C1685(R)f
ResistorsX1104Si. Transistor28A673(C)
Symbol DescriptionPart NumberSymbolDescriptionPart NumberX1105Si. Transistor2SC1685(R)
Main PCB. AssySU-1103AR1406voR 2002QVzZ3230-022X1106Si. Transistor2S8A673(C)
CRT Socket P.C.B. AssySU-3016AR1408Vv-R 2002QVZ3230-022x1301Si. Transistor2S8C1685(R)
R1410CMF R 6801WJQRX019J-6R8X1302Si. Transistor28C1685(R)
Outside of the P.C.B. Ass'yR1414OMR 3.3KQ1WJQRGO19J-3321303Si, Transistor28A673(C)
Symbol DescriptionPart NumberR1415OMR 27Ka1WJQRGO19J-272X1304Si. Transistor28C1685(R)
AVO1—Aficture Tube 13"370ESB22(E)R1421OMR 12Ka2WJQRGO29J-123xie0s(Gi Transistorespe7e
ADYO1 Abeflection Yoke€29123-VR1422«VOR 10KQVz3224-014Hciaoe, | Si hansiorsepia
PC MagnetA76366-AAFRi401AF= R 6822WKQRH024K-680MX1501Si. Transistor28C2610BK
Wedge30006AR1503.ACMF R 11.82%W +1%QRV142F-1182X1701Si. Transistor28C1685(P-S)
A\Flyback Transf.A19183-AR1504VvR 5KQQVZ3230-053D1101Si. DiodeWO6A
Ar11AFocusVRA46606-AR1509OMR 10KQ2WJQRGO29J-10301102Si. DiodeWO6A
AROS—_UNF Resistor 220.,25W. KQRF258K-221R1511OMR 5.6Ka2WJQRGO29J-562D1103Si. DiodewosA
Aco4.AC Capacitor 150pFAC1.5KV —_ QCZ0101-005R1514OmR 68022WJQRGO29J-68101301Si. Diode182473H
X01 _ Si, Transistor2SD869R1515CMF R 8201WJQRX019J-8R21401Si. Diodejeeerar
1CO1IC RegulatorSTR3831822.CMF _R 4.701WJQRX019J-4R7pie | UaeRDIOF(C)
LotDegaussing Coil21-1007-31R1523OMR S5602WJORGO29J-560beesSi. DiodeVO9E
Degaussing Coil Pin Terminal (2) 34-708-01R1528OMR 39021WJORGO19J-3911805Zener DiodeRD11E(B)
Degaussing Coil Pin TerminalR1534ZNRERZ-CO5ZK4711506Si. Diodewoes
Housing34-709-01vriso1ZNRERZ-COSDK271D1507Si. Diode18881
Groundstrap Assy34-697-04AR1703.ACMF R 39KQ%W +1%QRV122F-390201508Si. Diode182473H
Groundstrap Wire Terminal34-228-03AR1704 - ACMF R 7.68KQYW+1%= QRV142F-7681AD1701_ — AXZener DiodeD20Ev2
Groundstrap Spring (2)35-3560-014R1901 ~— A\PosistorA75414Abi901_—Assi, Diode181887A
BRSupport Bracket RH35-3919-01R1902UNF R 207WKQRFO76K-2ROAp 1902ASi. Diode1918874
BRSupport Bracket LH35-3919-02R1903,CMF R 5.623WJQRX039J-5RERionASi. Diode181887A
scSCREW 10-¥ Pix Tube Mtg. (4)31-631018-08R1904omR 10Ka2wJQRGO26J-103Z’
WAPyramidal Lockwasher (4)33-255-01AFR1901AF= R_ 2202%WKQRH124K-221MMiscellaneous
Clip P.C.B. Support (2)33-628-02SymbolDescriptionPart Number
Ground LugSsa04AF1901Fuse 1AQMF53U1-1ROS5-17
CHChassis Base38-452-01AF1902 — AUL Fuse 3AQMF66U1-3ROS
Page 89

10 YOKE

! vent. so4 TWIST CABLE ASSY 7

; ag tom, it 1xg208 Tr, witout DRIVER ‘SWEEP #0323 | exa229

|121-373oxcranesooee

SHUTDOWN e208 ! < KY ffcn l VOLTAGE

«| @ 2 sav se, BY i star 33] Ue voc] oy gate

Ld1feedeie pragoe

foov iz" ime Ff ae ‘cR3203 en I \ - _

_—s i a | i

tvovirey gS] dost

~ ——— aa _ sayy

\439;
Foca}-——s2—_|_omngoaet—aLoe9-186-03|
f—bo__aae]
~on—a~awore\

5-18 Siheawse SpecirteD, 93 EB 3R3 1 To 9- 186-03 R329

REFERENCE ONLY

ss

RGB COL SCHEMATIC FOR ~

g- 1a6- G3 2

SWEEP BOARD

OR MONITOR

ZENITH

RADIO CORP. CHICAGO, ILL. ISSUE

B | 3-186 M05 1-00087-A021

NOTES: (USED WITH CIRCUIT REFERENCE DF-SIONATORS)

SUMPER wie USED INSTEAD. SEE BARTS LIST FOR APPLICADLE USAGE, ©. -@ ¥ @— PROVISION ON PRITEE CIRCLIT BomRe,

Page 90

ZENITH MONITOR — SWEEP BOARD REPLACEMENT PARTS LIST

SWEEP BOARD (9-186-03)

Ref. No.PartNo.DescriptionRef. No.Part No.Description

CAPACITORS TRANSFORMERS & COILS

0213122-750847 MF, 38V, +20% Electrolytic3207149-454Core, Ferrite Bead
0215222-7508-01C + 22MF, 35V, +20% Electrolytic13220F-13834Core & Sleeving Assy. (149-509-01)
320122-7410-0510 MF, 100V, +20% ElectrolyticLXx326120-3976Coil Width
Cx320222-710-01C1 MF, SOV, +50%-10% ElectrolyticLX326220-3975Coil, Linearity, with 205-271 Hot Melt
6320322-7711-08C47 MF, 63V, +50% 10% Electrolytic320595-3344Transformer, Horizontal Driver
©x320422-7773-24A0.1 MF, 100V, +5% PolyesterTX320495-3581-01Transformer, Sweep
Cx320522-7523-010.01 MF, 2KV, +20% Disc
C320622-7708-04C4.7 MF, 25V, +50%-10% ElectrolyticRESISTORS
320722-5665330 PF, 1000V, +10% Disc74
6320922-72420.0018 MF, 200V, +10% DiscReisfeeceyed,aFCONa, Pedawn
321122-7777-20B0.047 MF, 200V, + 10% PolyesterR21163-9919-833K Onm, £2% 1/4W Film
0321222-7234560 PF, 500V, + 10% DiscRota63-9919-9610K Ohm, +2% 1/4W Film
321322-775-16A0.022 MF, 100V, +20% PolyesterRX320463-9921-802.2K Ohm, #5% 1/4W Film
0321422-7775-10A0.0068 MF, 100V, +20% PolyesterRX320663-78053.3K Ohm’ +5% 1/2W Carbon
0321622-5684470 PF, SOOV, +20% DiscRX320763-9921-3222 Ohm, +5% 1/4W Film
03217oo470 PF, SOOV, £20% DiscRX320863-10235-802.2K Ohm, +5% 1/4W Film
321822-7774-15C0.018 MF, 100V, +10% Polyesterxa200eaauEss 72Oban 28% WAW Film
C322222-742-100.001 MF, SOV, £10% AxialRX321063-78053.3K Ohm, +5% 1/2W Carbon
Cx322822-6486530 PF, 3KV, £10% DiscRXx321163-10810-073K Ohm, +1% 1/2W Film
x322922-7672-070.013 MF, 1.6KV, +5% PolypropyleneAX321463-10233-812.4K Ohm, +2% 1/4W Film
6323322-17280.68 MF, 200V, +10% PolyesterAXa21663-10810-06-12K Ohm. +1% 1/2W Film
C324422-7566-240.1 MF, 250V, +10% PolyesterRX321763-7760270 Ohm 5% 1/2W Carbon
C326122-7683-010.68 MF, 200V, +5% PolypropyleneRX3215.63-10235-9812K Ohm, 5% 1/4W Film
RX3218,63-10235-822.7K Ohm, +5% 1/4W Film
SEMICONDUCTORSRRX321963-10235-884.7K Ohm, +5% 1/4W Film
cR3202103-142-01Diode, Low Voltage322463-9946-884.7K Ohm, +5% 1/2W Film
R3203103-330ADiode, Low Voltage3225,63-10836-68 — 680 Ohm, +5% 2W Wire Wound
CRX3204103-308ADiode, Zener322663-10235-741.2K Ohm, +5% 1/4W Film
CR3205103-305Diode, Damper322763-10235-802.2K Ohm, +5% 1/4W Film
CR3206103-2848Diode, Low VoltageRX323563-10810-081.2K Ohm, +1% 1/2W Film
CR3207103-295-018Diode, Low VoltageX3240,53-10657-0410 Meg Ohm, +20% 1/2W Carbon
(used with 149-454)R324263-10243-802.2K Ohm, +5% 1/2W Film
cR3208103-295-01ADiode, Low Voltage324363-10243-802.2K Ohm, +5% 1/2W Film
CR3209103-142-01Diode, Low Voltage324463-7868100K Ohm, +5% 1/2W Carbon
R3210103-142-01Diode, Low Voltage326163-10444-86390 Ohm, +10% 5W Wire Wound
cR3211103-142-01Diode, Low Voltage326263-10565-65510 Ohin, +10% 1/2W Film
Qx3202121-975Transistor, NPN326363-10565-65510 Ohm, +10% 1/2W Film
0x3204121-973Transistor, PNP, Shutdown328263-10235-9610K Ohm, +5% 1/4W Film
3206121-1037Transistor, NPN, Forward Driver
Qx3207121-975Transistor, NPN, Shutdown
3209121-1040Transistor, NPN, Reverse Driver
Page 91

This page reads as a drawing: its text was drawn rather than typeset, and comes out in fragments. See the original scan.

Page 92

ZENITH MONITOR — MAIN BOARD REPLACEMENT PARTS LIST MAIN BOARD (Continued)

BoardBoardBoard
9-2279-2279-227
9-227-01Ref.No. PartNo.Description9-227-01Ref.No. PartNo.Description9-227-01Ref.No. PartNo.Description
RESISTORSRESISTORS (Continued).RESISTORS (Continued)
xX—RX210163-10565-3222 Ohm, +5%, 1/2W FilmXR261863-10235-731.1K Ohm, +5%, 1/4W FilmxXR322263-10235-40 47 Ohm, +5%, 1/4W Film
xXR2102 — 63-10243-56220 Ohm, +5%, 1/2W FilmxR251963-10235-937.5K Ohm, +5%, 1/4W FilmxX323163-99821 Ohm, +10%, 2W Wirewound
xXR210363-10235-88 4.7K Ohm, +5%, 1/2W FilmX251963-10235-822.7K Ohm, +5%, 1/4W FilmxX323363-10565-14 3.9Ohm, 5%, 1/2W Film
xX—-RX2104 63-10243-113 Ohm, +5%, 1/2W FilmxR252063-10235-802.2K Ohm, +5%, 1/4W FilmxXR3234—63-10565-14 3.9Ohm, +5%, 1/2W Film
xXRX2105 63-10243-113 Ohm, +5%, 1/2W FilmxR2521—63-10235-50120 Ohm, +5%, 1/4W FilmxX8323963-10244-20100K Ohm, +5%, 1/2W Film
xXR210663-10235-721K Ohm, +5%, 1/4W FiimX—-R252163-10235-48100 Ohm, +5%, 1/4W FilmxXR324163-82464 Ohm, 10W Wirewound
xXR210763-10235-66 560 Ohm, +5%, 1/4W FilmxR252263-10235-741.2K Ohm, +5%, 1/4W FilmxXR3244—63-10840-40 47 Ohm, +5%, 3W Film,
xX210863-10235-66 560 Ohm, +5%, 1/4W FilmxR252363-10236-28220K Onm, +5%, 1/4W FilmTin Oxide
xXR210963-105651 Ohm, +5%, 1/2W FilmXR252363-10236-52 2.2 Meg Ohm, +5%, 1/4W FilmxXR324563-10710A_—Thermistor
xXR211063-105651 Ohm, +5%, 1/2W FilmxXR252463-10235-90 5.6K Ohm, +5%, 1/4W FilmxXRX3246 63-10657-031.2 Meg Ohm, +20%,
xXR2t1163-105651 Ohm, +5%, 1/2W FilmxR252563-10235-56 220 Ohm, +5%, 1/4W Film1/2W Carbon
xXR211263-105651 Ohm, +5%, 1/2W FilmXR252563-10235-58 270 Ohm, +5%, 1/4W FilmXR326063-10243-9610K Ohm, +5%, 1/2W Film
xXR2113_83-10243-60 330 Ohm, +5%, 1/2W FilmxR252663-10235-80 2.2K Ohm, +5%, 1/4W FilmXR326163-10244-24150K Ohm, +5%, 1/4W Film
xXR211463-10235-721K Ohm, +5%, 1/4W FilmXR252663-10235-69 750 Ohm, +5%, 1/4W FilmX326263-10235-68680 Onm, +5%, 1/4W Film
xXR211563-10285-88 4.7K Ohm, +5%, 1/4W FilmxR2527—63-10857-315K Ohm,Control-RotaryxX340163-10236-461.2 Meg Ohm, +5%, 1/4W Film
xXR211663-10235-80 330 Ohm, +5%, 1/4W FilmSingie-BluexX340263-10236-22120K Ohm, +5%, 1/4W Film
xXR211763-10235-80 2.2K Ohm, +5%, 1/4W FilmX—R2527_—63-10857-26800 Ohm, Control-RotaryxXR340363-10235-86 3.9K Ohm,+5%, 1/4W Film
xXR2118—63-10235-88 4.7K Ohm, +5%, 1/4W FilmSingle-Blue Cut-OffxXR340463-10235-86 3.9K Ohm, +5%, 1/4W Film
xX211963-10235-54180 Ohm, +5%, 1/4W FilmxR252863-10857-301K Ohm, Control-RotaryxXR3405—63-10236-08 33K Ohm, +5%, 1/4W Film
xX = R212063-10565-082.2 Ohm, +5%, 1/2W FilmSingle-YellowxX340663-10235-68 680 Ohm, +5%, 1/4W Film
xXR212163-10243-52150 Onm, +5%, 1/2W FilmX—R252863-10857-26800 Ohm, Control-RotaryxX340763-10236-18 82K Ohm, +5%, 1/4W Film
xXR212263-10243-52150 Ohm, +5%, 1/2W FilmSingle-Blue DrivexXR340863-10236-0422K Ohm, +5%, 1/4W Film
xXR212563-9023-02550 Ohm, +20%, Control-xR252963-10235-76 1.5K Ohm, +5%, 1/4W FilmxXR340963-10857-17100K Ohm, Control-Rotary
Rotary Single-GRAXR252963-10235-751.3K Ohm, +5%, 1/4W FilmSingle-Green
XR212663-10243-66 560 Ohm, +5%, 1/2W FilmxR253063-10235-937.5K Ohm, +5%, 1/4W FilmxX341063-10236-31300K Ohm, +5%, 1/4W Film
xR212663-10243-53 160 Ohm, +5%, 1/2W FilmX253063-10235-822.7K Ohm, +5%, 1/4W FilmxX—R3411—63-10236-03 20K Ohm, +5%, 1/4W Film
X212763-10243-69750 Ohm, +5%, 1W CarbonxR253163-10235-80 2.2K Ohm, +5%, 1/4W FilmxX341263-10236-13 51K Ohm, +5%, 1/4W Film
xR212863-10243-66560 Ohm, +5%, 1/2W FilmxR253263-10235-50120 Ohm, +5%, 1/4W FilmxX341363-10236-0730K Ohm, +5%, 1/4W Film
XR212863-6058510 Ohm,. 1W CarbonXR253263-10235-48100 Ohm, +5%, 1/4W FilmxXR341463-10235-9812K Ohm, +5%, 1/4W Film
XR212963-10243-65510 Ohm, +5%, 1/2W CarbonxR253363-10235-741.2K Ohm, +5%, 1/4W FilmxXR341563-10236-0248K Ohm, +5%, 1/4W Film
xR250163-10236-28220K Ohm, +5%, 1/4W FilmR2534—63-10235-52150 Ohm, +5%. 1/4W FilmxXR341763-10243-60330 Ohm, +5%, 1/2W Film
XR250163-10236-52 2.2 Meg Ohm, +5%, 1/4W FilmxR253563-10235-52 150 Ohm, +5%, 1/4W FilmxX3418—63-10857-082K Ohm, Control-Rotary
xXR250263-10235-90 5.6K Ohm, +5%, 1/4W FilmxR253663-10235-52150 Ohm, +5%, 1/4W FilmSingle-Yeliow
xR250363-10235-56 220 Ohm, +5%, 1/4W Filmx253763-10235-52150 Ohm, +5%, 1/4W FilmxXR341963-10235-84 3.3K Ohm, +5%, 1/4W Film
XR250363-10235-58270 Ohm, +5%, 1/4W FilmxR253863-10235-56 +220 Ohm, +5%, 1/4W FilmxXR342063-10236-10 39K Ohm, +5%, 1/4W Film
xR250463-10235-802.2K Ohm, +5%, 1/4W FilmXR2538—63-10235-48+100 Ohm, +5%, 1/4W FilmxX342163-10235-731.1K Ohm, +5%, 1/4W Film
XR250463-10235-69750 Ohm, +5%, 1/4W FilmxR253963-10235-56 220 Ohm, +5%, 1/4W FilmxXR342263-10243-60 330 Ohm, +5%, 1/2W Film
xR250563-10857-115K Ohm, Contrc!-RotaryXR253963-10235-48100 Ohm, +5%, 1/4W FilmxXR342363-10243-60 330 Ohm, +5%, 1/2W Film
Single-REDxR254063-10235-56220 Ohm, +5%, 1/4W FitmxXR342463-10235-721K Ohm, +5%, 1/4W Film
XR250563-10857-27800 Ohm, Controi-RotaryXR254063-10235-48100 Ohm, +5%, 1/4W FilmxXR342563-10235-884.7K Ohm, +5%, 1/4W Film
Single-Red Cut-OffX254163-10235-54 180.0hm, +5%, 1/4W FilmxX342863-10235-82 2.7K Onm, +5%, 1/4W Film
xR250663-10857-301K Ohm, Control-RotaryXR254263-10235-53160 Ohm, +5%, 1/4W FilmxX342963-10235-761.5K Ohm, +5%, 1/4W Film
Single- YellowX254363-10235-54180 Ohm, +5%, 1/4W FilmxX343163-10235-80 2.2K Ohm, +5%, 1/4W Film
XR250663-10857-27800 Ohm, Control-RotaryXR2544—63-10235-54180 Ohm, +5%, 1/4W FilmxR343263-10235-55 200 Ohm, +5%, 1/4W Film
Single-Red DriveXR254563-10235-54180 Ohm, +5%, 1/4W FilmXR343263-10235-79 2K Ohm, +5%, 1/4W Film
xR250763-10235-761.5K Ohm, +5%, 1/4W FilmXR254663-10235-53160 Ohm, +5%, 1/4W FilmxXR343363-10236-20100K Ohm, +5%, 1/4W Film
XR250?63-10235-751.3K Ohm, +5%, 1/4W FilmXR254863-10235-67620 Ohm, +5%, 1/4W FilmxXR3434 — 63-10236-22120K Ohm, +5%, 1/4W Film
XR250863-10235-937.5K Ohm, +5%, 1/4W FilmXR254963-10235-67620 Ohm, +5%, 1/4W FilmxX343563-10235-63430 Ohm, +5%, 1/4W Film
xR250863-10235-822.7K Ohm, +5%, 1/4W FilmXR2550—63-10235-32 22 Ohm, +5%, 1/4W FilmxX — R3436—63-10235-721K Ohm, +5%, 1/4W Film
xR250963-10235-802.2K Ohm, +5%, 1/4W FilmXR255263-10235-32 22 Ohm, +5%, 1/4W FilmxXR343963-10243-79 2K Ohm, +5%, 1/2W Film
xXR251063-10235-50120 Ohm, +5%, 1/4W FilmXR2554—63-10235-32 22 Ohm, +5%, 1/4W FilmxXR344063-10235-86 3.9K Ohm, +5%, 1/4W Film
XR251063-10235-48100 Ohm, +5%, 1/4W FilmxX320163-10235-59 +300 Ohm, +5%, 1/4W FilmxR344163-10857100 Ohm, Control-Rotary
xR251163-10235-741.2K Ohm, +5%, 1/4W FilmxXR320263-10235-4468 Ohm, +5%, 1/4W FilmSingle-Horizontal Center
XR251163-10235-67620 Ohm, +5%, 1/4W FilmxXR320363-10235-52150 Ohm, +5%, 1/4W FilmXR3441 — 63-10857-02250 Ohm, Control-Rotary
xA251263-10236-28 220K Ohm, +5%, 1/4W FilmxXR320563-7781820 Ohm, +5%, 1/2W CarbonSingle-Horizontal Center
X251263-10236-522.2 Meg Ohm, +5%, 1/4W FilmxR3206F-1185112 Ohm, +10%, 10W ResistorxX344263-10235-86 3.9K Ohm, +5%, 1/4W Film
xXR251363-10235-905.6K Ohm, +5%, 1/4W Film& Splice Assy.xR344363-10235-65 510 Ohm, +5%, 1/4W Film
xR2514 — 63-10235-56220 Ohm, +5%, 1/4W FilmXR320663-10460-5012 Ohm, +10%, 10WXR3443—_63-10235-80 2.2K Ohm, +5%, 1/4W Film
XR251463-10235-58 270 Ohm, +5%, 1/4W FilmWirewoundxX—R3444—_63-10235-60 330 Ohm, +5%, 1/4W Film
xR251563-10235-802.2K Ohm, +5%, 1/4W FilmxXR3210—63-10420-312 Ohm, +5%, 2W WirewoundxX344563-10235-80 2.2K Ohm, +5%, 1/4W Film
R251563-10235-71910 Ohm, +5%, 1/4W FilmxX321263-10235-761.5K Ohm, +5%, 1/4W FilmX344663-10235-721K Ohm,+5%, 1/4W Film
xR251663-10857-325K Ohm, Control-RotaryxR321363-10235-833K Ohm, +5%, 1/4W FilmxR3449 — 63-10235-761.5K Ohm, +5%, 1/4W Film
Sing\e-GreenX321363-10235-86 3.9K Ohm, +5%, 1/4W FilmxR3451 — 63-10235-822.7K Ohm, +5%, 1/4W Film
XR251663-10857-25 800 Ohm, Control-RotaryxXR3214 — 63-10235-741.2K Ohm, +5%, 1/4W FilmXR3451_63-10235-88 4.7K Ohm, +5%, 1/4W Film
Single-Green Cut-OffxR321563-10244-38560K Ohm, +5%, 1/2W FilmxXR345263-10235-92 6.8K Ohm, +5%, 1/4W Film
xR251763-10857-301K Ohm, Control-RotaryXR321563-10244-40 680K Ohm,+5%, 1/2W FilmXR345363-10235-751.3K Ohm, +5%, 1/4W Film
Single-YellowxXR321663-10244-25160K Ohm, +5%, 1/2W FilmxXR3461 — 63-1023615K Ohm, +5%, 1/4W Film
XR251763-10857-25800 Ohm, Control-RotaryxXR321763-10244-33 360K Ohm,+5%, 1/2W FilmxXR3462—-63-10236-1351K Ohm, +5%, 1/4W Film
Single-Green DrivexXR321863-10235-802.2K Ohm, +5%, 1/4W Film
xR251863-10235-761.5K Ohm, +5%, 1/4W FilmX—R3219_—_63-10244-38560K Ohm, +5%, 1/2W Film
Ref. No.Part No.Description

CAPACITORS

210122-7775-10A0.0088 MF, 100V +20% Polyester
C210222-7775-24A0.1 MF, 100V +20% Polyester
6210322-7709-09C100 MF, 35V +50%~10% Electrolytic
C210422-7613-24D0.01 MF, 50V +10% Disc
210522-7390-020.47 MF, 50V +20% Electrolytic

C2106 22-7710-07C — 33MF, 50V +50%-10% Electrolytic

C210722-7615-03D0.0033 MF, SOV +80%~10% Disc
211022-7742-100.001 MF, 50V +10% Polyester
C21122-7774-17A0.027 MF, 100V +10% Polyester
C217622-7725680 MF, SOV +100%~10% Electrolytic
C250122-7621-42C220 PF, SOV +5% Disc
250222-7621-42C220 PF, 50V +5% Disc
C250322-7621-42C220 PF, SOV +5% Disc
320122-1775-24A0.1 MF, 100V +20% Polyester
C320422-76034.7 ME, 315V +100%~-10% Electrolytic
C320522-35120.01 MF, 1KV +40%-20% Disc
C320622-7603-01A10 MF, 315V +100%-10% Electrolytic
C320722-7742-100.001 MF, SOV +10% Axial
C320822-7742-100.001 MF, 50V +10% Axial
320922-7395470 PF, 500V +5% Disc
C323422-7395470 PF, 500V +5% Disc
C323622-7861-142200 MF, 35V +20% Electrolytic
C324622-7603-01A10 MF, 315V +100%-10% Electrolytic
C324722-7860-12470 MF, 25V +20% Electrolytic
324922-7431-08(0.0047 MF, +20% Disc
Cx325022-7431-06(0.0047 MF, +20% Disc
325122-78110.001 MF, 1KV +10% Disc
6325222-78110.001 MF, 1KV +10% Disc
C325322-78110.001 MF, 1KV +10% Disc
0325422-7404-0622 MF, 16V +20% Electrolytic
6325622-7508-05B2200 MF, 35V +50%—10% Electrolytic
C325722-7395470 PF, 500V +5% Disc
340122-7613-24D0.01 MF, 50V +10% Disc
c340222-7406-011.0 MF, 35V +20% Electrolytic
C340322-7773-18A0.033 MF, 100V +5% Polyester
C340422-7773-17A0.027 MF, 100V +5% Polyester
C340522-7775-10A0.0068 MF, 100V +20% Polyester
340722-7710-01A1.0 MF, 50V +50%~10% Electrolytic
C340922-7709-09C100 MF, 35V +100%~-10% Electrolytic
C341022-7404-06A22 MF, 16V +20% Electrolytic NP
c34i122-7708-09100 MF, 25V +50%~10% Electrolytic
C341222-7710-01C1.0 MF, SOV +50%~10% Electrolytic
C341322-7562-320.47 MF, 100V +5% Polyester
C341422-7774-16A0.022 MF, 100V +10% Polyester
C341922-7751-39180 PF, 50V +5% Axial
342022-7710-01C1.0 MF, 50V +50%~10% Electrolytic
342122-7773-18B0.033 MF, 100V +5% Polyester
342222-7613-24D0.01 MF, S0V +10% Disc
342322-7613-08D470 PF, 50V +10% Disc
C342422-7742-05390 PF, 50V +10% Axial
C342522-7742-100.001 MF, SOV +10% Axial
C342622-7742-100.01 MF, SOV +10% Axial
C342722-7647-35C150 PF, +10% Axial
C342822-7774-120.01 MF, 100V +10% Polyester
342822-7774-20A0.047 MF, 100V +10% Polyester

(on-01 version)

342922-7405-044.7 MF, 25V +20% Electrolytic NP
342922-74060.47 MF, 35V +20% Electrolytic NP

(on-01 version)

343022-7613-24D0.01 MF, 50V +10% Disc
C343122-7774-16A0,022 MF, 100V +10% Polyester
C343422-7742-08470 PF, SOV +10% Axial
C343622-7613-24C0.01 MF, 100V +10% Disc
0345022-7739-29A0.27 MF, 100V +10% Polyester
345022-7619-41C200 PF, SCV +5% Disc

(on-01 version)

346122-7710-01C1.0 MF, SOV +50%-10% Electrolytic
C346222-7710-01C1.0 MF, SOV +50%~10% Electrolytic
C346222-7739-090.0056 MF, 100V +10% Polyester

(on-01 version)

C346322-750847 MF, 35V +20% Electrolytic
Page 93

MAIN BOARD (Continued)

Ref. No.Part No.Description

SEMICONDUCTORS

cR2104103-142-01Diode, Low Voltage
CR2105103-254-01Diode, Low Voltage
CR2106103-254-01Diode, Low Voltage
cR2107103-254-01Diode, Low Voltage
CR2501103-142-01Diode, Low Voltage
R2502103-142-01Diode, Low Voltage
CR2503,103-142-01Diode, Low Voltage
CR3202103-330Diode, Low Voltage
CR3205,103-309-01Diode, Zener 10V 1W
CR3206,103-254-01Diode, Low Voltage
CR3208103-326ADiode, Low Voltage
CR3210103-254-01Diode, Low Voltage
CR3211103-254-01Diode, Low Voltage
CR3214103-284-ADiode, Low Voltage
CR3217103-326ADiode, Low Voltage
cR3219103-330ADiode, Low Voltage
CR3223103-330ADiode, Low Voltage
cR3224103-330ADiode, Low Voltage
CR3231103-315-06ADiode
CR3232103-315-06ADiode
CR3233,103-315-06ADiode
CR3234103-315-06ADiode
CR3235,103-2844Diode, Low Voltage
CR3401103-142-01Diode, Low Voltage
CR3404103-143-01Diode. Low Voltage
CR3405103-142-01Diode, Low Voltage
CR3406103-142-01Diode, Low Voltage
CR3408103-279-14Diode, Zener 6.8V 1/2W
2101F-10896Transistor & Heat Sink Assy.
2102F-10896Transistor & Heat Sink Assy.
2103121-975Transistor NPN
Q2104121-1064Transistor PNP
25014121-1019Transistor PNP
2502121-895Transistor NPN
2502121-551Transistor NPN

(on-01 version)

2503121-1019Transistor PNP
Q2504121-895Transistor NPN
2504421-551Transistor NPN

(on-01 version)

2505121-1019Transistor PNP
2506121-895Transistor NPN
Q2506121-551Transistor NPN

(on-01 version)

2507121-1019Transistor
02508121-1019Transistor
Q2509121-1019Transistor
Q3200F-12737Transistor & Heat Sink Assy.
93201121-499-01Transistor NPN Regular Feed Back
Q3202121-1034Transistor NPN
Q3203121-1059Transistor PNP
Q3401121-895Transistor NPN
Q3402121-986Transistor PNP
Q3403121-985Transistor NPN
3404121-895Transistor NPN
93405121-895Transistor NPN

TRANSFORMERS & COILS

L250220-3887-01Coil Peaking1.2UH
1250320-3887-01Coil Peaking 1.2UH
1.250420-3887-01Coil Peaking1.2UH
320120-2021Coil Peaking 100 UH
Lx320295-3501-01Transformer Choke 60 UH
340120-3831Coil Peaking 663 UH
340220-3998Coil Peaking 39 UH
340220-4026Coil Turnable 39UH

(on-01 version) ZENITH MONITOR — CRT SOCKET BOARD

REPLACEMENT PARTS LIST

Ref. No.

C5101 C5102

15102 15103 15104

Q5101 Q5102 Q5103

R5101 5102 5103 5104 R5105, R5106 R5107 R5108 R5109 R5110. R5111 R5112 R5113 R5114 R5115,

5A2 5c2

5X7

cn CRT SOCKET (9-155-10)

Part No. Description

CAPACITORS 22-4671 0.01 MF, 1.5KV, +80%—20% Disc 22-3512 0.01 MF, 1KV, +40%-—10% Disc

TRANSFORMERS & COILS 20-3887-28E 220MH Peaking 20-3887-28E 220MH Peaking 20-3887-28E 220MH Peaking

SEMICONDUCTORS F7510. Transistor, NPN, Video Out, Blue F7510 Transistor, NPN, Video Out, Red F7510 Transistor, NPN, Video Out, Green

RESISTORS 63-10840-88 4.7K Ohm, +5%, 3W Film 63-7785 1K Ohm, £10%, 1/2W Carbon 63-7785 1K Ohm, +10%, 1/2W Carbon 63-10235-54 180 Ohm, +5%, 1/4W Film 63-10235-48 100 Ohm, +5%, 1/4W Film 63-7785 1K Ohm, +10%, 1/2W Carbon, 63-7785 1K Ohm, +10%, 1/2W Carbon 63-7785 1K Ohm, +10%, 1/2W Carbon 63-7785 1K Ohm, +10%, 1/2W Carbon 63-7785 1K Ohm, +10%, 1/2W Carbon 63-7799 2.2K Ohm, +10%, 1/2W Carbon 63-10840-88 4.7K Ohm, +5%, 3W Carbon 63-10840-88 4.7K Ohm, +5%, 3W Carbon 63-10235-54 180 Ohm, +5%, 1/4W Film 63-10235-54 180 Ohm, +5%, 1/4W Film

MISCELLANEOUS 86-799 Stake Connector 4/.156 86-799 Stake Connector4/.156 86-799 Stake Connector 2/.156 86-799 Stake Connector 1/.312 A-10008 CRT Socket

ey xy

Page 94

9-155-10 \ (204-960) I

| 1

QS101 121-1034 BLUE QUT. psio2 | 1K 1 |

\Rsi01aaa| {

4.7K wi Hi ic Lsioz 7 ee RS104

|180.!
|1744Hl

TH

| £5103 i "200K

!||

S113 $R5112

'Q5103)4.7K4.7K|

L5101 rgirios * it

Q5102

i+7121-1034 |

\ RED OUT | . es10z Jc [e +01

|lodRS115

| 180

'1/40|

/ S114 oe cs

174HWe1

' \

'A8|

! 1 ' |

| Sc2 5A2

|we|“GROUND

i “Gi [ BASE +140 VOC

NOTE: 1, ALL RESISTORS ARE 1/2WATT UNLESS OTHERWISE SPECIFIED.

NOTES: (USED WITH CIRCUIT REFERENCE DESIGNATORS) PA. = SEE PARTS LIST FOR APPLICABLE USACE. @—e- = JUMPER WIRE USED INSTEAD. —@ = © = PROVISION ON PRINTED CIRCUIT BOARO.

5-23

Page 95

TO H.O.T. ASSY

A-|0530

73-3059

ia] C2 Le PF 1

NOTE: M05 1-00087-A023 WIRE HOLES #22GA. SCHEMATIC FOR A-10539 a WIDTH STEF ASSY ( 9-136-03 ZENITH | SWEEP MODULE RADIO CORP.| B A-|0530 CHICAGO, ILL.

5-24

Page 96

3v3 [oo] MAIN MODULE | _ (SEE CHART) |

[-}363t12
alyab2y

;/ooo000 | & i

3W3rt33—|~-
aooo}|
|B303|||
aof||
foaooco—|
—{is}an|0
_or)|D.C. GROUNC
eleAG4
a'WC-
ul|oeOR
.SWEEP MODULE_.
(SEE CHART)|!
Exie
aoo0000apo3833R3or~
ooooo' |:

: te SIT 1 tt tt 4+—-. IMPORTANT sven SERED CELE, IADER,

MikeIme PaTHe OR SINAL UE
2a52853F33183883R8arn

20 3 ON FROM THE ZENITH RACIC CCR-

oooo0aooo0ooa[20oo Ooo oOLi» 6ALL ZOMPONENTS SHOULC SE RE-
+[216}(Th THBES IUENTICAL, TO

EMTs AN Teac UGenriowe wirdnig AN

fi}iHy BoweET GNEORM” TC LORIE LNAL

pouePly, CAYLUP etn" SMe “ETIUN CF REPAIRS Cepecime iRcuiTs age aS ICEL Yo ERE

YOKE(SEE CHART)1 VENT SHC<K ANE ETRE: HAIARC, THELC AREAS

w10 ARE SHADE CN THE cchENATIE FoR ERST AIR | Teentirieariow, THe certer Tn THE, [fe NUMBER LESTONATE 1 MEONENT. DU PAPE’ ABER y CEVIATIONS ARE ALL CWEL | WITHOUT FRIGR APPRUVAL SY THE PRUCUCT

TO DEGAUSSERLofy]| SAFETY eNSINECR ING LEFARTHENT .
cxy(s]ee ee eeeaeoo

nC TL TAGKAW itt C _ mre RT in ken ~ Threenays ime tem PATIL Ce Ie CATeST SAEED Ac PERE ORMAIOE. IMPROVEMENT BRANGEC INTC. THe SET Ic NUT GLA

  • UNTI_ THE MEW SERVICE LITERAT the
_=oaPRINTEC
=363[2]
pha} e-o-0s|;6+ ASSEMBLY

= WIDTH STEP

{2}a—t(SEE CHART)
{L___

\

\ao[|

VIDEO OUT (SEE CHART) SH3

[e 90 |5x3etnM05 1-00087-A025
;-a

LL 8

8=FOR

| rrOO al Li OD K JL one

TTeeTe1S3J€

LE { Y) bag <> ir 5-25 RATE | CHICASL, fu.

Page 97

4 1k s i mt

ae = oon

  • at = aoe L| 7 = ra

LE 1st coms

Ta Shas ete ed MT. 1958 _ om m1 44 im vey 4 na sen se 1d ie i m4 ma na mt mt mt a snap sip-no® we Lyt oles ms i

os is Let

tos

f f we ee SE eee ye ee ee eee ee eee be oe ee ee ce ee ee ne 4

:POWER CHASSIS *70VA - UPRIGHTBALLY / MIDWAY
1-5 rena BARRIER STR OLMISMSV ~ GORE10601 W BELMONT AVE.
aPART NO. A945- 00036-0002FRANKLIN" PARC IL 6013!

7 OWG. NO. MOS! - 00945 -BO5I_ INGREAGED FUSE VALUES] WO Was SaMP “now aaup™ | 315-63 Was AMP — Now SAMP ADDED PART NO. (U.L.) FEV | INCREASED Flise VALUE WAS. Sane “NOW ‘SAME

Page 98

ar aa

Se fee Lit " 2 baw so-80

TWOREASED FUSE VALUES WAS 3AMP = NOW 4AMP WAS 4aMP — NOW SAMP ADDED _PART_NO._(U.L.) INCREASED FUSE “VALUE WAS. 3AMP = NOW AMP PART NO. A845 -00036-0000 DWG NO. “MO5I-00945-B046 POWER CHASSIS *70VA BALLY, / MIDWAY coc! 060! iu Narceme MODEL Frat Paes 6D

Page 99

FF

i : we

REV. @] NGREASED FUSE VALUES | WB WAS SAMP'- NOW 4AMP- | 3-15-63, ADDED PART NO. (UL) REV. ©) | INCREASED FUSE VALUE | MB WAS 3AMP— Now aame | 3-24-83

POWER CHASSIS "125 VA

SV, = GOH, PART NO, A945 - 5 A945 - 00020-0000 DWG. NO. MOSI - 00945 -BO37 BALLY / M IDWAY. I 10601 W. BELMONT AVE. FRANKLIN PARK, IL. 60131